p += scnprintf(buf + p, bufsz - p, "Statistics Flag(0x%X):\n",
le32_to_cpu(il->_3945.stats.flag));
if (le32_to_cpu(il->_3945.stats.flag) &
- UCODE_STATISTICS_CLEAR_MSK)
+ UCODE_STATS_CLEAR_MSK)
p += scnprintf(buf + p, bufsz - p,
"\tStatistics have been cleared\n");
p += scnprintf(buf + p, bufsz - p, "\tOperational Frequency: %s\n",
(le32_to_cpu(il->_3945.stats.flag) &
- UCODE_STATISTICS_FREQUENCY_MSK)
+ UCODE_STATS_FREQUENCY_MSK)
? "2.4 GHz" : "5.2 GHz");
p += scnprintf(buf + p, bufsz - p, "\tTGj Narrow Band: %s\n",
(le32_to_cpu(il->_3945.stats.flag) &
- UCODE_STATISTICS_NARROW_BAND_MSK)
+ UCODE_STATS_NARROW_BAND_MSK)
? "enabled" : "disabled");
return p;
}
* stats request from the host as well as for the periodic
* stats notifications (after received beacons) from the uCode.
*/
- il->rx_handlers[REPLY_STATISTICS_CMD] = il3945_reply_stats;
- il->rx_handlers[STATISTICS_NOTIFICATION] = il3945_hw_rx_stats;
+ il->rx_handlers[REPLY_STATS_CMD] = il3945_reply_stats;
+ il->rx_handlers[STATS_NOTIFICATION] = il3945_hw_rx_stats;
il_setup_rx_scan_handlers(il);
il->rx_handlers[CARD_STATE_NOTIFICATION] = il3945_rx_card_state_notif;
* Ucode should set SEQ_RX_FRAME bit if ucode-originated,
* but apparently a few don't get set; catch them here. */
reclaim = !(pkt->hdr.sequence & SEQ_RX_FRAME) &&
- pkt->hdr.cmd != STATISTICS_NOTIFICATION &&
+ pkt->hdr.cmd != STATS_NOTIFICATION &&
pkt->hdr.cmd != REPLY_TX;
/* Based on type of command response or notification,
struct il_rx_pkt *pkt = rxb_addr(rxb);
__le32 *flag = (__le32 *)&pkt->u.raw;
- if (le32_to_cpu(*flag) & UCODE_STATISTICS_CLEAR_MSK) {
+ if (le32_to_cpu(*flag) & UCODE_STATS_CLEAR_MSK) {
#ifdef CONFIG_IWLEGACY_DEBUGFS
memset(&il->_3945.accum_stats, 0,
sizeof(struct il3945_notif_stats));
stat_band24 = !!(((struct il_notif_stats *)
stat_resp)->flag &
- STATISTICS_REPLY_FLG_BAND_24G_MSK);
+ STATS_REPLY_FLG_BAND_24G_MSK);
stat_chnum = le32_to_cpu(((struct il_notif_stats *)
stat_resp)->flag) >> 16;
flag = le32_to_cpu(il->_4965.stats.flag);
p += scnprintf(buf + p, bufsz - p, "Statistics Flag(0x%X):\n", flag);
- if (flag & UCODE_STATISTICS_CLEAR_MSK)
+ if (flag & UCODE_STATS_CLEAR_MSK)
p += scnprintf(buf + p, bufsz - p,
"\tStatistics have been cleared\n");
p += scnprintf(buf + p, bufsz - p, "\tOperational Frequency: %s\n",
- (flag & UCODE_STATISTICS_FREQUENCY_MSK)
+ (flag & UCODE_STATS_FREQUENCY_MSK)
? "2.4 GHz" : "5.2 GHz");
p += scnprintf(buf + p, bufsz - p, "\tTGj Narrow Band: %s\n",
- (flag & UCODE_STATISTICS_NARROW_BAND_MSK)
+ (flag & UCODE_STATS_NARROW_BAND_MSK)
? "enabled" : "disabled");
return p;
change = ((il->_4965.stats.general.common.temperature !=
pkt->u.stats.general.common.temperature) ||
((il->_4965.stats.flag &
- STATISTICS_REPLY_FLG_HT40_MODE_MSK) !=
+ STATS_REPLY_FLG_HT40_MODE_MSK) !=
(pkt->u.stats.flag &
- STATISTICS_REPLY_FLG_HT40_MODE_MSK)));
+ STATS_REPLY_FLG_HT40_MODE_MSK)));
#ifdef CONFIG_IWLEGACY_DEBUGFS
il4965_accumulative_stats(il, (__le32 *)&pkt->u.stats);
#endif
memcpy(&il->_4965.stats, &pkt->u.stats,
sizeof(il->_4965.stats));
- set_bit(S_STATISTICS, &il->status);
+ set_bit(S_STATS, &il->status);
/* Reschedule the stats timer to occur in
* REG_RECALIB_PERIOD seconds to ensure we get a
msecs_to_jiffies(REG_RECALIB_PERIOD * 1000));
if (unlikely(!test_bit(S_SCANNING, &il->status)) &&
- (pkt->hdr.cmd == STATISTICS_NOTIFICATION)) {
+ (pkt->hdr.cmd == STATS_NOTIFICATION)) {
il4965_rx_calc_noise(il);
queue_work(il->workqueue, &il->run_time_calib_work);
}
{
struct il_rx_pkt *pkt = rxb_addr(rxb);
- if (le32_to_cpu(pkt->u.stats.flag) & UCODE_STATISTICS_CLEAR_MSK) {
+ if (le32_to_cpu(pkt->u.stats.flag) & UCODE_STATS_CLEAR_MSK) {
#ifdef CONFIG_IWLEGACY_DEBUGFS
memset(&il->_4965.accum_stats, 0,
sizeof(struct il_notif_stats));
* This callback is provided in order to send a stats request.
*
* This timer function is continually reset to execute within
- * REG_RECALIB_PERIOD seconds since the last STATISTICS_NOTIFICATION
+ * REG_RECALIB_PERIOD seconds since the last STATS_NOTIFICATION
* was received. We need to ensure we receive the stats in order
* to update the temperature used for calibrating the TXPOWER.
*/
* stats request from the host as well as for the periodic
* stats notifications (after received beacons) from the uCode.
*/
- il->rx_handlers[REPLY_STATISTICS_CMD] = il4965_reply_stats;
- il->rx_handlers[STATISTICS_NOTIFICATION] = il4965_rx_stats;
+ il->rx_handlers[REPLY_STATS_CMD] = il4965_reply_stats;
+ il->rx_handlers[STATS_NOTIFICATION] = il4965_rx_stats;
il_setup_rx_scan_handlers(il);
(pkt->hdr.cmd != REPLY_RX) &&
(pkt->hdr.cmd != REPLY_RX_MPDU_CMD) &&
(pkt->hdr.cmd != REPLY_COMPRESSED_BA) &&
- (pkt->hdr.cmd != STATISTICS_NOTIFICATION) &&
+ (pkt->hdr.cmd != STATS_NOTIFICATION) &&
(pkt->hdr.cmd != REPLY_TX);
/* Based on type of command response or notification,
if (test_bit(S_TEMPERATURE, &il->status) &&
(il->_4965.stats.flag &
- STATISTICS_REPLY_FLG_HT40_MODE_MSK)) {
+ STATS_REPLY_FLG_HT40_MODE_MSK)) {
D_TEMP("Running HT40 temperature calibration\n");
R1 = (s32)le32_to_cpu(il->card_alive_init.therm_r1[1]);
R2 = (s32)le32_to_cpu(il->card_alive_init.therm_r2[1]);
{
int temp_diff;
- if (!test_bit(S_STATISTICS, &il->status)) {
+ if (!test_bit(S_STATS, &il->status)) {
D_TEMP("Temperature not updated -- no stats.\n");
return 0;
}
* uCode provides all 4 values to the driver via the "initialize alive"
* notification (see struct il4965_init_alive_resp). After the runtime uCode
* image loads, uCode updates the R4 value via stats notifications
- * (see STATISTICS_NOTIFICATION), which occur after each received beacon
- * when associated, or can be requested via REPLY_STATISTICS_CMD.
+ * (see STATS_NOTIFICATION), which occur after each received beacon
+ * when associated, or can be requested via REPLY_STATS_CMD.
*
* NOTE: uCode provides the R4 value as a 23-bit signed value. Driver
* must sign-extend to 32 bits before applying formula below.
REPLY_BT_CONFIG = 0x9b,
/* Statistics */
- REPLY_STATISTICS_CMD = 0x9c,
- STATISTICS_NOTIFICATION = 0x9d,
+ REPLY_STATS_CMD = 0x9c,
+ STATS_NOTIFICATION = 0x9d,
/* RF-KILL commands and notifications */
CARD_STATE_NOTIFICATION = 0xa1,
#define IL_PROBE_STATUS_FAIL_TTL BIT(1)
#define IL_PROBE_STATUS_FAIL_BT BIT(2)
-#define NUMBER_OF_STATISTICS 1 /* first __le32 is good CRC */
+#define NUMBER_OF_STATS 1 /* first __le32 is good CRC */
/*
* SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
*/
u8 num_probe_not_sent; /* not enough time to send */
__le32 tsf_low;
__le32 tsf_high;
- __le32 stats[NUMBER_OF_STATISTICS];
+ __le32 stats[NUMBER_OF_STATS];
} __packed;
/*
__le32 reserved3;
} __packed;
-#define UCODE_STATISTICS_CLEAR_MSK (0x1 << 0)
-#define UCODE_STATISTICS_FREQUENCY_MSK (0x1 << 1)
-#define UCODE_STATISTICS_NARROW_BAND_MSK (0x1 << 2)
+#define UCODE_STATS_CLEAR_MSK (0x1 << 0)
+#define UCODE_STATS_FREQUENCY_MSK (0x1 << 1)
+#define UCODE_STATS_NARROW_BAND_MSK (0x1 << 2)
/*
- * REPLY_STATISTICS_CMD = 0x9c,
+ * REPLY_STATS_CMD = 0x9c,
* all devices identical.
*
* This command triggers an immediate response containing uCode stats.
- * The response is in the same format as STATISTICS_NOTIFICATION 0x9d, below.
+ * The response is in the same format as STATS_NOTIFICATION 0x9d, below.
*
* If the CLEAR_STATS configuration flag is set, uCode will clear its
* internal copy of the stats (counters) after issuing the response.
- * This flag does not affect STATISTICS_NOTIFICATIONs after beacons (see below).
+ * This flag does not affect STATS_NOTIFICATIONs after beacons (see below).
*
* If the DISABLE_NOTIF configuration flag is set, uCode will not issue
- * STATISTICS_NOTIFICATIONs after received beacons (see below). This flag
- * does not affect the response to the REPLY_STATISTICS_CMD 0x9c itself.
+ * STATS_NOTIFICATIONs after received beacons (see below). This flag
+ * does not affect the response to the REPLY_STATS_CMD 0x9c itself.
*/
#define IL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
#define IL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
} __packed;
/*
- * STATISTICS_NOTIFICATION = 0x9d (notification only, not a command)
+ * STATS_NOTIFICATION = 0x9d (notification only, not a command)
*
* By default, uCode issues this notification after receiving a beacon
* while associated. To disable this behavior, set DISABLE_NOTIF flag in the
- * REPLY_STATISTICS_CMD 0x9c, above.
+ * REPLY_STATS_CMD 0x9c, above.
*
* Statistics counters continue to increment beacon after beacon, but are
- * cleared when changing channels or when driver issues REPLY_STATISTICS_CMD
+ * cleared when changing channels or when driver issues REPLY_STATS_CMD
* 0x9c with CLEAR_STATS bit set (see above).
*
* uCode also issues this notification during scans. uCode clears stats
* appropriately so that each notification contains stats for only the
* one channel that has just been scanned.
*/
-#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
-#define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
+#define STATS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
+#define STATS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
struct il3945_notif_stats {
__le32 flag;
* time listening, not transmitting). Driver must adjust sensitivity so that
* the ratio of actual false alarms to actual Rx time falls within this range.
*
- * While associated, uCode delivers STATISTICS_NOTIFICATIONs after each
+ * While associated, uCode delivers STATS_NOTIFICATIONs after each
* received beacon. These provide information to the driver to analyze the
* sensitivity. Don't analyze stats that come in from scanning, or any
* other non-associated-network source. Pertinent stats include:
* This command sets the relative gains of 4965 device's 3 radio receiver chains.
*
* After the first association, driver should accumulate signal and noise
- * stats from the STATISTICS_NOTIFICATIONs that follow the first 20
+ * stats from the STATS_NOTIFICATIONs that follow the first 20
* beacons from the associated network (don't collect stats that come
* in from scanning, or any other non-network source).
*
};
if (flags & CMD_ASYNC)
- return il_send_cmd_pdu_async(il, REPLY_STATISTICS_CMD,
+ return il_send_cmd_pdu_async(il, REPLY_STATS_CMD,
sizeof(struct il_stats_cmd),
&stats_cmd, NULL);
else
- return il_send_cmd_pdu(il, REPLY_STATISTICS_CMD,
+ return il_send_cmd_pdu(il, REPLY_STATS_CMD,
sizeof(struct il_stats_cmd),
&stats_cmd);
}
#define S_TEMPERATURE 8
#define S_GEO_CONFIGURED 9
#define S_EXIT_PENDING 10
-#define S_STATISTICS 12
+#define S_STATS 12
#define S_SCANNING 13
#define S_SCAN_ABORTING 14
#define S_SCAN_HW 15
test_bit(S_GEO_CONFIGURED, &il->status));
pos += scnprintf(buf + pos, bufsz - pos, "S_EXIT_PENDING:\t %d\n",
test_bit(S_EXIT_PENDING, &il->status));
- pos += scnprintf(buf + pos, bufsz - pos, "S_STATISTICS:\t %d\n",
- test_bit(S_STATISTICS, &il->status));
+ pos += scnprintf(buf + pos, bufsz - pos, "S_STATS:\t %d\n",
+ test_bit(S_STATS, &il->status));
pos += scnprintf(buf + pos, bufsz - pos, "S_SCANNING:\t %d\n",
test_bit(S_SCANNING, &il->status));
pos += scnprintf(buf + pos, bufsz - pos, "S_SCAN_ABORTING:\t %d\n",
IL_CMD(REPLY_TX_BEACON);
IL_CMD(REPLY_TX_PWR_TBL_CMD);
IL_CMD(REPLY_BT_CONFIG);
- IL_CMD(REPLY_STATISTICS_CMD);
- IL_CMD(STATISTICS_NOTIFICATION);
+ IL_CMD(REPLY_STATS_CMD);
+ IL_CMD(STATS_NOTIFICATION);
IL_CMD(CARD_STATE_NOTIFICATION);
IL_CMD(MISSED_BEACONS_NOTIFICATION);
IL_CMD(REPLY_CT_KILL_CONFIG_CMD);
projects / mirror_ubuntu-zesty-kernel.git / commitdiff