Use codespell to fix lots of typos over frontends.
Manually verified to avoid false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
return value / resolution + (value % resolution > 0 ? 1 : 0);
}
-/* Retrieve the Initialzation Registers */
+/* Retrieve the Initialization Registers */
static u16 MXL_GetInitRegister(struct dvb_frontend *fe, u8 *RegNum,
u8 *RegVal, int *count)
{
struct dvb_frontend *fe;
u32 lpf_freq; /* LPF frequency[kHz]. Default: symbol rate */
- bool half_step; /* use PLL frequency step of 500Hz istead of 1000Hz */
+ bool half_step; /* use PLL frequency step of 500Hz instead of 1000Hz */
};
/* special values indicating to use the default in qm1d1b0004_config */
/*
* record IMC results by input gain/phase location then adjust
- * gain or phase positive 1 step and negtive 1 step,
+ * gain or phase positive 1 step and negative 1 step,
* both record results
*/
}
/*
- * Disables IMR callibration. That emulates the same behaviour
+ * Disables IMR calibration. That emulates the same behaviour
* as what is done by rtl-sdr userspace library. Useful for testing
*/
if (no_imr_cal) {
* Standby modes, EP3 [7:5]
*
* | SM || SM_LT || SM_XT || mode description
- * |=====\\=======\\=======\\===================================
+ * |=====\\=======\\=======\\====================================
* | 0 || 0 || 0 || normal mode
- * |-----||-------||-------||-----------------------------------
+ * |-----||-------||-------||------------------------------------
* | || || || standby mode w/ slave tuner output
- * | 1 || 0 || 0 || & loop thru & xtal oscillator on
- * |-----||-------||-------||-----------------------------------
+ * | 1 || 0 || 0 || & loop through & xtal oscillator on
+ * |-----||-------||-------||------------------------------------
* | 1 || 1 || 0 || standby mode w/ xtal oscillator on
- * |-----||-------||-------||-----------------------------------
+ * |-----||-------||-------||------------------------------------
* | 1 || 1 || 1 || power off
*
*/
if (tda_fail(ret))
goto fail;
- tda_dbg("%s mode: xtal oscillator %s, slave tuner loop thru %s\n",
+ tda_dbg("%s mode: xtal oscillator %s, slave tuner loop through %s\n",
standby ? "standby" : "active",
priv->output_opt & TDA18271_OUTPUT_XT_OFF ? "off" : "on",
priv->output_opt & TDA18271_OUTPUT_LT_OFF ? "off" : "on");
};
enum tda18271_output_options {
- /* slave tuner output & loop thru & xtal oscillator always on */
+ /* slave tuner output & loop through & xtal oscillator always on */
TDA18271_OUTPUT_LT_XT_ON = 0,
- /* slave tuner output loop thru off */
+ /* slave tuner output loop through off */
TDA18271_OUTPUT_LT_OFF = 1,
/* xtal oscillator off */
if (rc < 0)
goto ret;
- /* Informations from real testing of DVB-T and radio part,
- coeficient for one dB is 0xff.
+ /* Information from real testing of DVB-T and radio part,
+ coefficient for one dB is 0xff.
*/
tuner_dbg("Signal strength: -%ddB (%05d)\n", value >> 8, value);