--- /dev/null
+AMCC NDFC (NanD Flash Controller)
+
+Required properties:
+- compatible : "ibm,ndfc".
+- reg : should specify chip select and size used for the chip (0x2000).
+
+Optional properties:
+- ccr : NDFC config and control register value (default 0).
+- bank-settings : NDFC bank configuration register value (default 0).
+
+Notes:
+- partition(s) - follows the OF MTD standard for partitions
+
+Example:
+
+ndfc@1,0 {
+ compatible = "ibm,ndfc";
+ reg = <0x00000001 0x00000000 0x00002000>;
+ ccr = <0x00001000>;
+ bank-settings = <0x80002222>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nand {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x00000000 0x00200000>;
+ };
+ partition@200000 {
+ label = "root";
+ reg = <0x00200000 0x03E00000>;
+ };
+ };
+};
+
+
--- /dev/null
+ 4xx/Axon EMAC ethernet nodes
+
+ The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
+ the Axon bridge. To operate this needs to interact with a this
+ special McMAL DMA controller, and sometimes an RGMII or ZMII
+ interface. In addition to the nodes and properties described
+ below, the node for the OPB bus on which the EMAC sits must have a
+ correct clock-frequency property.
+
+ i) The EMAC node itself
+
+ Required properties:
+ - device_type : "network"
+
+ - compatible : compatible list, contains 2 entries, first is
+ "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
+ 405gp, Axon) and second is either "ibm,emac" or
+ "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon",
+ "ibm,emac4"
+ - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
+ - interrupt-parent : optional, if needed for interrupt mapping
+ - reg : <registers mapping>
+ - local-mac-address : 6 bytes, MAC address
+ - mal-device : phandle of the associated McMAL node
+ - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated
+ with this EMAC
+ - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated
+ with this EMAC
+ - cell-index : 1 cell, hardware index of the EMAC cell on a given
+ ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
+ each Axon chip)
+ - max-frame-size : 1 cell, maximum frame size supported in bytes
+ - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
+ operations.
+ For Axon, 2048
+ - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
+ operations.
+ For Axon, 2048.
+ - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate
+ thresholds).
+ For Axon, 0x00000010
+ - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
+ in bytes.
+ For Axon, 0x00000100 (I think ...)
+ - phy-mode : string, mode of operations of the PHY interface.
+ Supported values are: "mii", "rmii", "smii", "rgmii",
+ "tbi", "gmii", rtbi", "sgmii".
+ For Axon on CAB, it is "rgmii"
+ - mdio-device : 1 cell, required iff using shared MDIO registers
+ (440EP). phandle of the EMAC to use to drive the
+ MDIO lines for the PHY used by this EMAC.
+ - zmii-device : 1 cell, required iff connected to a ZMII. phandle of
+ the ZMII device node
+ - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII
+ channel or 0xffffffff if ZMII is only used for MDIO.
+ - rgmii-device : 1 cell, required iff connected to an RGMII. phandle
+ of the RGMII device node.
+ For Axon: phandle of plb5/plb4/opb/rgmii
+ - rgmii-channel : 1 cell, required iff connected to an RGMII. Which
+ RGMII channel is used by this EMAC.
+ Fox Axon: present, whatever value is appropriate for each
+ EMAC, that is the content of the current (bogus) "phy-port"
+ property.
+
+ Optional properties:
+ - phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
+ a search is performed.
+ - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY
+ for, used if phy-address is absent. bit 0x00000001 is
+ MDIO address 0.
+ For Axon it can be absent, though my current driver
+ doesn't handle phy-address yet so for now, keep
+ 0x00ffffff in it.
+ - phy-handle : Used to describe configurations where a external PHY
+ is used. Please refer to:
+ Documentation/devicetree/bindings/net/ethernet.txt
+ - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
+ operations (if absent the value is the same as
+ rx-fifo-size). For Axon, either absent or 2048.
+ - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
+ operations (if absent the value is the same as
+ tx-fifo-size). For Axon, either absent or 2048.
+ - tah-device : 1 cell, optional. If connected to a TAH engine for
+ offload, phandle of the TAH device node.
+ - tah-channel : 1 cell, optional. If appropriate, channel used on the
+ TAH engine.
+ - fixed-link : Fixed-link subnode describing a link to a non-MDIO
+ managed entity. See
+ Documentation/devicetree/bindings/net/fixed-link.txt
+ for details.
+ - mdio subnode : When the EMAC has a phy connected to its local
+ mdio, which us supported by the kernel's network
+ PHY library in drivers/net/phy, there must be device
+ tree subnode with the following required properties:
+ - #address-cells: Must be <1>.
+ - #size-cells: Must be <0>.
+
+ For PHY definitions: Please refer to
+ Documentation/devicetree/bindings/net/phy.txt and
+ Documentation/devicetree/bindings/net/ethernet.txt
+
+ Examples:
+
+ EMAC0: ethernet@40000800 {
+ device_type = "network";
+ compatible = "ibm,emac-440gp", "ibm,emac";
+ interrupt-parent = <&UIC1>;
+ interrupts = <1c 4 1d 4>;
+ reg = <40000800 70>;
+ local-mac-address = [00 04 AC E3 1B 1E];
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0 1>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <5dc>;
+ rx-fifo-size = <1000>;
+ tx-fifo-size = <800>;
+ phy-mode = "rmii";
+ phy-map = <00000001>;
+ zmii-device = <&ZMII0>;
+ zmii-channel = <0>;
+ };
+
+ EMAC1: ethernet@ef600c00 {
+ device_type = "network";
+ compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
+ interrupt-parent = <&EMAC1>;
+ interrupts = <0 1>;
+ #interrupt-cells = <1>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
+ 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
+ reg = <0xef600c00 0x000000c4>;
+ local-mac-address = [000000000000]; /* Filled in by U-Boot */
+ mal-device = <&MAL0>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <9000>;
+ rx-fifo-size = <16384>;
+ tx-fifo-size = <2048>;
+ fifo-entry-size = <10>;
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ phy-map = <0x00000000>;
+ rgmii-device = <&RGMII0>;
+ rgmii-channel = <0>;
+ tah-device = <&TAH0>;
+ tah-channel = <0>;
+ has-inverted-stacr-oc;
+ has-new-stacr-staopc;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+ };
+ };
+
+
+ ii) McMAL node
+
+ Required properties:
+ - device_type : "dma-controller"
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
+ emac) and the second is either "ibm,mcmal" or
+ "ibm,mcmal2".
+ For Axon, "ibm,mcmal-axon","ibm,mcmal2"
+ - interrupts : <interrupt mapping for the MAL interrupts sources:
+ 5 sources: tx_eob, rx_eob, serr, txde, rxde>.
+ For Axon: This is _different_ from the current
+ firmware. We use the "delayed" interrupts for txeob
+ and rxeob. Thus we end up with mapping those 5 MPIC
+ interrupts, all level positive sensitive: 10, 11, 32,
+ 33, 34 (in decimal)
+ - dcr-reg : < DCR registers range >
+ - dcr-parent : if needed for dcr-reg
+ - num-tx-chans : 1 cell, number of Tx channels
+ - num-rx-chans : 1 cell, number of Rx channels
+
+ iii) ZMII node
+
+ Required properties:
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,zmii-CHIP" where CHIP is the host ASIC (like
+ EMAC) and the second is "ibm,zmii".
+ For Axon, there is no ZMII node.
+ - reg : <registers mapping>
+
+ iv) RGMII node
+
+ Required properties:
+ - compatible : compatible list, containing 2 entries, first is
+ "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
+ EMAC) and the second is "ibm,rgmii".
+ For Axon, "ibm,rgmii-axon","ibm,rgmii"
+ - reg : <registers mapping>
+ - revision : as provided by the RGMII new version register if
+ available.
+ For Axon: 0x0000012a
+++ /dev/null
- 4xx/Axon EMAC ethernet nodes
-
- The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
- the Axon bridge. To operate this needs to interact with a this
- special McMAL DMA controller, and sometimes an RGMII or ZMII
- interface. In addition to the nodes and properties described
- below, the node for the OPB bus on which the EMAC sits must have a
- correct clock-frequency property.
-
- i) The EMAC node itself
-
- Required properties:
- - device_type : "network"
-
- - compatible : compatible list, contains 2 entries, first is
- "ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
- 405gp, Axon) and second is either "ibm,emac" or
- "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon",
- "ibm,emac4"
- - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
- - reg : <registers mapping>
- - local-mac-address : 6 bytes, MAC address
- - mal-device : phandle of the associated McMAL node
- - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated
- with this EMAC
- - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated
- with this EMAC
- - cell-index : 1 cell, hardware index of the EMAC cell on a given
- ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
- each Axon chip)
- - max-frame-size : 1 cell, maximum frame size supported in bytes
- - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
- operations.
- For Axon, 2048
- - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
- operations.
- For Axon, 2048.
- - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate
- thresholds).
- For Axon, 0x00000010
- - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
- in bytes.
- For Axon, 0x00000100 (I think ...)
- - phy-mode : string, mode of operations of the PHY interface.
- Supported values are: "mii", "rmii", "smii", "rgmii",
- "tbi", "gmii", rtbi", "sgmii".
- For Axon on CAB, it is "rgmii"
- - mdio-device : 1 cell, required iff using shared MDIO registers
- (440EP). phandle of the EMAC to use to drive the
- MDIO lines for the PHY used by this EMAC.
- - zmii-device : 1 cell, required iff connected to a ZMII. phandle of
- the ZMII device node
- - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII
- channel or 0xffffffff if ZMII is only used for MDIO.
- - rgmii-device : 1 cell, required iff connected to an RGMII. phandle
- of the RGMII device node.
- For Axon: phandle of plb5/plb4/opb/rgmii
- - rgmii-channel : 1 cell, required iff connected to an RGMII. Which
- RGMII channel is used by this EMAC.
- Fox Axon: present, whatever value is appropriate for each
- EMAC, that is the content of the current (bogus) "phy-port"
- property.
-
- Optional properties:
- - phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
- a search is performed.
- - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY
- for, used if phy-address is absent. bit 0x00000001 is
- MDIO address 0.
- For Axon it can be absent, though my current driver
- doesn't handle phy-address yet so for now, keep
- 0x00ffffff in it.
- - phy-handle : Used to describe configurations where a external PHY
- is used. Please refer to:
- Documentation/devicetree/bindings/net/ethernet.txt
- - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
- operations (if absent the value is the same as
- rx-fifo-size). For Axon, either absent or 2048.
- - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
- operations (if absent the value is the same as
- tx-fifo-size). For Axon, either absent or 2048.
- - tah-device : 1 cell, optional. If connected to a TAH engine for
- offload, phandle of the TAH device node.
- - tah-channel : 1 cell, optional. If appropriate, channel used on the
- TAH engine.
- - fixed-link : Fixed-link subnode describing a link to a non-MDIO
- managed entity. See
- Documentation/devicetree/bindings/net/fixed-link.txt
- for details.
- - mdio subnode : When the EMAC has a phy connected to its local
- mdio, which us supported by the kernel's network
- PHY library in drivers/net/phy, there must be device
- tree subnode with the following required properties:
- - #address-cells: Must be <1>.
- - #size-cells: Must be <0>.
-
- For PHY definitions: Please refer to
- Documentation/devicetree/bindings/net/phy.txt and
- Documentation/devicetree/bindings/net/ethernet.txt
-
- Examples:
-
- EMAC0: ethernet@40000800 {
- device_type = "network";
- compatible = "ibm,emac-440gp", "ibm,emac";
- interrupt-parent = <&UIC1>;
- interrupts = <1c 4 1d 4>;
- reg = <40000800 70>;
- local-mac-address = [00 04 AC E3 1B 1E];
- mal-device = <&MAL0>;
- mal-tx-channel = <0 1>;
- mal-rx-channel = <0>;
- cell-index = <0>;
- max-frame-size = <5dc>;
- rx-fifo-size = <1000>;
- tx-fifo-size = <800>;
- phy-mode = "rmii";
- phy-map = <00000001>;
- zmii-device = <&ZMII0>;
- zmii-channel = <0>;
- };
-
- EMAC1: ethernet@ef600c00 {
- device_type = "network";
- compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
- interrupt-parent = <&EMAC1>;
- interrupts = <0 1>;
- #interrupt-cells = <1>;
- #address-cells = <0>;
- #size-cells = <0>;
- interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
- 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
- reg = <0xef600c00 0x000000c4>;
- local-mac-address = [000000000000]; /* Filled in by U-Boot */
- mal-device = <&MAL0>;
- mal-tx-channel = <0>;
- mal-rx-channel = <0>;
- cell-index = <0>;
- max-frame-size = <9000>;
- rx-fifo-size = <16384>;
- tx-fifo-size = <2048>;
- fifo-entry-size = <10>;
- phy-mode = "rgmii";
- phy-handle = <&phy0>;
- phy-map = <0x00000000>;
- rgmii-device = <&RGMII0>;
- rgmii-channel = <0>;
- tah-device = <&TAH0>;
- tah-channel = <0>;
- has-inverted-stacr-oc;
- has-new-stacr-staopc;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy0: ethernet-phy@0 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- };
- };
- };
-
-
- ii) McMAL node
-
- Required properties:
- - device_type : "dma-controller"
- - compatible : compatible list, containing 2 entries, first is
- "ibm,mcmal-CHIP" where CHIP is the host ASIC (like
- emac) and the second is either "ibm,mcmal" or
- "ibm,mcmal2".
- For Axon, "ibm,mcmal-axon","ibm,mcmal2"
- - interrupts : <interrupt mapping for the MAL interrupts sources:
- 5 sources: tx_eob, rx_eob, serr, txde, rxde>.
- For Axon: This is _different_ from the current
- firmware. We use the "delayed" interrupts for txeob
- and rxeob. Thus we end up with mapping those 5 MPIC
- interrupts, all level positive sensitive: 10, 11, 32,
- 33, 34 (in decimal)
- - dcr-reg : < DCR registers range >
- - dcr-parent : if needed for dcr-reg
- - num-tx-chans : 1 cell, number of Tx channels
- - num-rx-chans : 1 cell, number of Rx channels
-
- iii) ZMII node
-
- Required properties:
- - compatible : compatible list, containing 2 entries, first is
- "ibm,zmii-CHIP" where CHIP is the host ASIC (like
- EMAC) and the second is "ibm,zmii".
- For Axon, there is no ZMII node.
- - reg : <registers mapping>
-
- iv) RGMII node
-
- Required properties:
- - compatible : compatible list, containing 2 entries, first is
- "ibm,rgmii-CHIP" where CHIP is the host ASIC (like
- EMAC) and the second is "ibm,rgmii".
- For Axon, "ibm,rgmii-axon","ibm,rgmii"
- - reg : <registers mapping>
- - revision : as provided by the RGMII new version register if
- available.
- For Axon: 0x0000012a
+++ /dev/null
-AMCC NDFC (NanD Flash Controller)
-
-Required properties:
-- compatible : "ibm,ndfc".
-- reg : should specify chip select and size used for the chip (0x2000).
-
-Optional properties:
-- ccr : NDFC config and control register value (default 0).
-- bank-settings : NDFC bank configuration register value (default 0).
-
-Notes:
-- partition(s) - follows the OF MTD standard for partitions
-
-Example:
-
-ndfc@1,0 {
- compatible = "ibm,ndfc";
- reg = <0x00000001 0x00000000 0x00002000>;
- ccr = <0x00001000>;
- bank-settings = <0x80002222>;
- #address-cells = <1>;
- #size-cells = <1>;
-
- nand {
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "kernel";
- reg = <0x00000000 0x00200000>;
- };
- partition@200000 {
- label = "root";
- reg = <0x00200000 0x03E00000>;
- };
- };
-};
-
-
projects / mirror_ubuntu-focal-kernel.git / commitdiff