+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-rm9200dk.c
- *
- * Copyright (C) 2005 SAN People
- *
- * Epson S1D framebuffer glue code is:
- * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91rm9200_mc.h>
-#include <mach/at91_ramc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-
-
-static void __init dk_init_early(void)
-{
- /* Initialize processor: 18.432 MHz crystal */
- at91_initialize(18432000);
-}
-
-static struct macb_platform_data __initdata dk_eth_data = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-};
-
-static struct at91_usbh_data __initdata dk_usbh_data = {
- .ports = 2,
- .vbus_pin = {-EINVAL, -EINVAL},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-static struct at91_udc_data __initdata dk_udc_data = {
- .vbus_pin = AT91_PIN_PD4,
- .pullup_pin = AT91_PIN_PD5,
-};
-
-static struct at91_cf_data __initdata dk_cf_data = {
- .irq_pin = -EINVAL,
- .det_pin = AT91_PIN_PB0,
- .vcc_pin = -EINVAL,
- .rst_pin = AT91_PIN_PC5,
-};
-
-#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct mci_platform_data __initdata dk_mci0_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = -EINVAL,
- .wp_pin = -EINVAL,
- },
-};
-#endif
-
-static struct spi_board_info dk_spi_devices[] = {
- { /* DataFlash chip */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- },
- { /* UR6HCPS2-SP40 PS2-to-SPI adapter */
- .modalias = "ur6hcps2",
- .chip_select = 1,
- .max_speed_hz = 250 * 1000,
- },
- { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
- .modalias = "tlv1504",
- .chip_select = 2,
- .max_speed_hz = 20 * 1000 * 1000,
- },
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 3,
- .max_speed_hz = 15 * 1000 * 1000,
- }
-#endif
-};
-
-static struct i2c_board_info __initdata dk_i2c_devices[] = {
- {
- I2C_BOARD_INFO("ics1523", 0x26),
- },
- {
- I2C_BOARD_INFO("x9429", 0x28),
- },
- {
- I2C_BOARD_INFO("24c1024", 0x50),
- }
-};
-
-static struct mtd_partition __initdata dk_nand_partition[] = {
- {
- .name = "NAND Partition 1",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct atmel_nand_data __initdata dk_nand_data = {
- .ale = 22,
- .cle = 21,
- .det_pin = AT91_PIN_PB1,
- .rdy_pin = AT91_PIN_PC2,
- .enable_pin = -EINVAL,
- .ecc_mode = NAND_ECC_SOFT,
- .on_flash_bbt = 1,
- .parts = dk_nand_partition,
- .num_parts = ARRAY_SIZE(dk_nand_partition),
-};
-
-#define DK_FLASH_BASE AT91_CHIPSELECT_0
-#define DK_FLASH_SIZE SZ_2M
-
-static struct physmap_flash_data dk_flash_data = {
- .width = 2,
-};
-
-static struct resource dk_flash_resource = {
- .start = DK_FLASH_BASE,
- .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device dk_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &dk_flash_data,
- },
- .resource = &dk_flash_resource,
- .num_resources = 1,
-};
-
-static struct gpio_led dk_leds[] = {
- {
- .name = "led0",
- .gpio = AT91_PIN_PB2,
- .active_low = 1,
- .default_trigger = "heartbeat",
- }
-};
-
-static void __init dk_board_init(void)
-{
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
- at91_add_device_serial();
- /* Ethernet */
- at91_add_device_eth(&dk_eth_data);
- /* USB Host */
- at91_add_device_usbh(&dk_usbh_data);
- /* USB Device */
- at91_add_device_udc(&dk_udc_data);
- at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
- /* Compact Flash */
- at91_add_device_cf(&dk_cf_data);
- /* I2C */
- at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
- /* SPI */
- at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- /* DataFlash card */
- at91_set_gpio_output(AT91_PIN_PB7, 0);
-#else
- /* MMC */
- at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
- at91_add_device_mci(0, &dk_mci0_data);
-#endif
- /* NAND */
- at91_add_device_nand(&dk_nand_data);
- /* NOR Flash */
- platform_device_register(&dk_flash);
- /* LEDs */
- at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
- /* VGA */
-// dk_add_device_video();
-}
-
-MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
- /* Maintainer: SAN People/Atmel */
- .init_time = at91rm9200_timer_init,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = dk_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = dk_board_init,
-MACHINE_END
projects / mirror_ubuntu-zesty-kernel.git / commitdiff