vmpoff= [KNL,S390] Perform z/VM CP command after power off.
Format: <command>
+ vsyscall= [X86-64]
+ Controls the behavior of vsyscalls (i.e. calls to
+ fixed addresses of 0xffffffffff600x00 from legacy
+ code). Most statically-linked binaries and older
+ versions of glibc use these calls. Because these
+ functions are at fixed addresses, they make nice
+ targets for exploits that can control RIP.
+
+ emulate [default] Vsyscalls turn into traps and are
+ emulated reasonably safely.
+
+ native Vsyscalls are native syscall instructions.
+ This is a little bit faster than trapping
+ and makes a few dynamic recompilers work
+ better than they would in emulation mode.
+ It also makes exploits much easier to write.
+
+ none Vsyscalls don't work at all. This makes
+ them quite hard to use for exploits but
+ might break your system.
+
vt.cur_default= [VT] Default cursor shape.
Format: 0xCCBBAA, where AA, BB, and CC are the same as
the parameters of the <Esc>[?A;B;Cc escape sequence;
This option was added in bonding version 3.4.0.
+all_slaves_active
+
+ Specifies that duplicate frames (received on inactive ports) should be
+ dropped (0) or delivered (1).
+
+ Normally, bonding will drop duplicate frames (received on inactive
+ ports), which is desirable for most users. But there are some times
+ it is nice to allow duplicate frames to be delivered.
+
+ The default value is 0 (drop duplicate frames received on inactive
+ ports).
+
arp_interval
Specifies the ARP link monitoring frequency in milliseconds.
determined. See the High Availability section for additional
information. The default value is 0.
+min_links
+
+ Specifies the minimum number of links that must be active before
+ asserting carrier. It is similar to the Cisco EtherChannel min-links
+ feature. This allows setting the minimum number of member ports that
+ must be up (link-up state) before marking the bond device as up
+ (carrier on). This is useful for situations where higher level services
+ such as clustering want to ensure a minimum number of low bandwidth
+ links are active before switchover. This option only affect 802.3ad
+ mode.
+
+ The default value is 0. This will cause carrier to be asserted (for
+ 802.3ad mode) whenever there is an active aggregator, regardless of the
+ number of available links in that aggregator. Note that, because an
+ aggregator cannot be active without at least one available link,
+ setting this option to 0 or to 1 has the exact same effect.
+
mode
Specifies one of the bonding policies. The default is
--- /dev/null
+Scaling in the Linux Networking Stack
+
+
+Introduction
+============
+
+This document describes a set of complementary techniques in the Linux
+networking stack to increase parallelism and improve performance for
+multi-processor systems.
+
+The following technologies are described:
+
+ RSS: Receive Side Scaling
+ RPS: Receive Packet Steering
+ RFS: Receive Flow Steering
+ Accelerated Receive Flow Steering
+ XPS: Transmit Packet Steering
+
+
+RSS: Receive Side Scaling
+=========================
+
+Contemporary NICs support multiple receive and transmit descriptor queues
+(multi-queue). On reception, a NIC can send different packets to different
+queues to distribute processing among CPUs. The NIC distributes packets by
+applying a filter to each packet that assigns it to one of a small number
+of logical flows. Packets for each flow are steered to a separate receive
+queue, which in turn can be processed by separate CPUs. This mechanism is
+generally known as “Receive-side Scaling” (RSS). The goal of RSS and
+the other scaling techniques to increase performance uniformly.
+Multi-queue distribution can also be used for traffic prioritization, but
+that is not the focus of these techniques.
+
+The filter used in RSS is typically a hash function over the network
+and/or transport layer headers-- for example, a 4-tuple hash over
+IP addresses and TCP ports of a packet. The most common hardware
+implementation of RSS uses a 128-entry indirection table where each entry
+stores a queue number. The receive queue for a packet is determined
+by masking out the low order seven bits of the computed hash for the
+packet (usually a Toeplitz hash), taking this number as a key into the
+indirection table and reading the corresponding value.
+
+Some advanced NICs allow steering packets to queues based on
+programmable filters. For example, webserver bound TCP port 80 packets
+can be directed to their own receive queue. Such “n-tuple” filters can
+be configured from ethtool (--config-ntuple).
+
+==== RSS Configuration
+
+The driver for a multi-queue capable NIC typically provides a kernel
+module parameter for specifying the number of hardware queues to
+configure. In the bnx2x driver, for instance, this parameter is called
+num_queues. A typical RSS configuration would be to have one receive queue
+for each CPU if the device supports enough queues, or otherwise at least
+one for each cache domain at a particular cache level (L1, L2, etc.).
+
+The indirection table of an RSS device, which resolves a queue by masked
+hash, is usually programmed by the driver at initialization. The
+default mapping is to distribute the queues evenly in the table, but the
+indirection table can be retrieved and modified at runtime using ethtool
+commands (--show-rxfh-indir and --set-rxfh-indir). Modifying the
+indirection table could be done to give different queues different
+relative weights.
+
+== RSS IRQ Configuration
+
+Each receive queue has a separate IRQ associated with it. The NIC triggers
+this to notify a CPU when new packets arrive on the given queue. The
+signaling path for PCIe devices uses message signaled interrupts (MSI-X),
+that can route each interrupt to a particular CPU. The active mapping
+of queues to IRQs can be determined from /proc/interrupts. By default,
+an IRQ may be handled on any CPU. Because a non-negligible part of packet
+processing takes place in receive interrupt handling, it is advantageous
+to spread receive interrupts between CPUs. To manually adjust the IRQ
+affinity of each interrupt see Documentation/IRQ-affinity. Some systems
+will be running irqbalance, a daemon that dynamically optimizes IRQ
+assignments and as a result may override any manual settings.
+
+== Suggested Configuration
+
+RSS should be enabled when latency is a concern or whenever receive
+interrupt processing forms a bottleneck. Spreading load between CPUs
+decreases queue length. For low latency networking, the optimal setting
+is to allocate as many queues as there are CPUs in the system (or the
+NIC maximum, if lower). Because the aggregate number of interrupts grows
+with each additional queue, the most efficient high-rate configuration
+is likely the one with the smallest number of receive queues where no
+CPU that processes receive interrupts reaches 100% utilization. Per-cpu
+load can be observed using the mpstat utility.
+
+
+RPS: Receive Packet Steering
+============================
+
+Receive Packet Steering (RPS) is logically a software implementation of
+RSS. Being in software, it is necessarily called later in the datapath.
+Whereas RSS selects the queue and hence CPU that will run the hardware
+interrupt handler, RPS selects the CPU to perform protocol processing
+above the interrupt handler. This is accomplished by placing the packet
+on the desired CPU’s backlog queue and waking up the CPU for processing.
+RPS has some advantages over RSS: 1) it can be used with any NIC,
+2) software filters can easily be added to hash over new protocols,
+3) it does not increase hardware device interrupt rate (although it does
+introduce inter-processor interrupts (IPIs)).
+
+RPS is called during bottom half of the receive interrupt handler, when
+a driver sends a packet up the network stack with netif_rx() or
+netif_receive_skb(). These call the get_rps_cpu() function, which
+selects the queue that should process a packet.
+
+The first step in determining the target CPU for RPS is to calculate a
+flow hash over the packet’s addresses or ports (2-tuple or 4-tuple hash
+depending on the protocol). This serves as a consistent hash of the
+associated flow of the packet. The hash is either provided by hardware
+or will be computed in the stack. Capable hardware can pass the hash in
+the receive descriptor for the packet; this would usually be the same
+hash used for RSS (e.g. computed Toeplitz hash). The hash is saved in
+skb->rx_hash and can be used elsewhere in the stack as a hash of the
+packet’s flow.
+
+Each receive hardware queue has an associated list of CPUs to which
+RPS may enqueue packets for processing. For each received packet,
+an index into the list is computed from the flow hash modulo the size
+of the list. The indexed CPU is the target for processing the packet,
+and the packet is queued to the tail of that CPU’s backlog queue. At
+the end of the bottom half routine, IPIs are sent to any CPUs for which
+packets have been queued to their backlog queue. The IPI wakes backlog
+processing on the remote CPU, and any queued packets are then processed
+up the networking stack.
+
+==== RPS Configuration
+
+RPS requires a kernel compiled with the CONFIG_RPS kconfig symbol (on
+by default for SMP). Even when compiled in, RPS remains disabled until
+explicitly configured. The list of CPUs to which RPS may forward traffic
+can be configured for each receive queue using a sysfs file entry:
+
+ /sys/class/net/<dev>/queues/rx-<n>/rps_cpus
+
+This file implements a bitmap of CPUs. RPS is disabled when it is zero
+(the default), in which case packets are processed on the interrupting
+CPU. Documentation/IRQ-affinity.txt explains how CPUs are assigned to
+the bitmap.
+
+== Suggested Configuration
+
+For a single queue device, a typical RPS configuration would be to set
+the rps_cpus to the CPUs in the same cache domain of the interrupting
+CPU. If NUMA locality is not an issue, this could also be all CPUs in
+the system. At high interrupt rate, it might be wise to exclude the
+interrupting CPU from the map since that already performs much work.
+
+For a multi-queue system, if RSS is configured so that a hardware
+receive queue is mapped to each CPU, then RPS is probably redundant
+and unnecessary. If there are fewer hardware queues than CPUs, then
+RPS might be beneficial if the rps_cpus for each queue are the ones that
+share the same cache domain as the interrupting CPU for that queue.
+
+
+RFS: Receive Flow Steering
+==========================
+
+While RPS steers packets solely based on hash, and thus generally
+provides good load distribution, it does not take into account
+application locality. This is accomplished by Receive Flow Steering
+(RFS). The goal of RFS is to increase datacache hitrate by steering
+kernel processing of packets to the CPU where the application thread
+consuming the packet is running. RFS relies on the same RPS mechanisms
+to enqueue packets onto the backlog of another CPU and to wake up that
+CPU.
+
+In RFS, packets are not forwarded directly by the value of their hash,
+but the hash is used as index into a flow lookup table. This table maps
+flows to the CPUs where those flows are being processed. The flow hash
+(see RPS section above) is used to calculate the index into this table.
+The CPU recorded in each entry is the one which last processed the flow.
+If an entry does not hold a valid CPU, then packets mapped to that entry
+are steered using plain RPS. Multiple table entries may point to the
+same CPU. Indeed, with many flows and few CPUs, it is very likely that
+a single application thread handles flows with many different flow hashes.
+
+rps_sock_table is a global flow table that contains the *desired* CPU for
+flows: the CPU that is currently processing the flow in userspace. Each
+table value is a CPU index that is updated during calls to recvmsg and
+sendmsg (specifically, inet_recvmsg(), inet_sendmsg(), inet_sendpage()
+and tcp_splice_read()).
+
+When the scheduler moves a thread to a new CPU while it has outstanding
+receive packets on the old CPU, packets may arrive out of order. To
+avoid this, RFS uses a second flow table to track outstanding packets
+for each flow: rps_dev_flow_table is a table specific to each hardware
+receive queue of each device. Each table value stores a CPU index and a
+counter. The CPU index represents the *current* CPU onto which packets
+for this flow are enqueued for further kernel processing. Ideally, kernel
+and userspace processing occur on the same CPU, and hence the CPU index
+in both tables is identical. This is likely false if the scheduler has
+recently migrated a userspace thread while the kernel still has packets
+enqueued for kernel processing on the old CPU.
+
+The counter in rps_dev_flow_table values records the length of the current
+CPU's backlog when a packet in this flow was last enqueued. Each backlog
+queue has a head counter that is incremented on dequeue. A tail counter
+is computed as head counter + queue length. In other words, the counter
+in rps_dev_flow_table[i] records the last element in flow i that has
+been enqueued onto the currently designated CPU for flow i (of course,
+entry i is actually selected by hash and multiple flows may hash to the
+same entry i).
+
+And now the trick for avoiding out of order packets: when selecting the
+CPU for packet processing (from get_rps_cpu()) the rps_sock_flow table
+and the rps_dev_flow table of the queue that the packet was received on
+are compared. If the desired CPU for the flow (found in the
+rps_sock_flow table) matches the current CPU (found in the rps_dev_flow
+table), the packet is enqueued onto that CPU’s backlog. If they differ,
+the current CPU is updated to match the desired CPU if one of the
+following is true:
+
+- The current CPU's queue head counter >= the recorded tail counter
+ value in rps_dev_flow[i]
+- The current CPU is unset (equal to NR_CPUS)
+- The current CPU is offline
+
+After this check, the packet is sent to the (possibly updated) current
+CPU. These rules aim to ensure that a flow only moves to a new CPU when
+there are no packets outstanding on the old CPU, as the outstanding
+packets could arrive later than those about to be processed on the new
+CPU.
+
+==== RFS Configuration
+
+RFS is only available if the kconfig symbol CONFIG_RFS is enabled (on
+by default for SMP). The functionality remains disabled until explicitly
+configured. The number of entries in the global flow table is set through:
+
+ /proc/sys/net/core/rps_sock_flow_entries
+
+The number of entries in the per-queue flow table are set through:
+
+ /sys/class/net/<dev>/queues/tx-<n>/rps_flow_cnt
+
+== Suggested Configuration
+
+Both of these need to be set before RFS is enabled for a receive queue.
+Values for both are rounded up to the nearest power of two. The
+suggested flow count depends on the expected number of active connections
+at any given time, which may be significantly less than the number of open
+connections. We have found that a value of 32768 for rps_sock_flow_entries
+works fairly well on a moderately loaded server.
+
+For a single queue device, the rps_flow_cnt value for the single queue
+would normally be configured to the same value as rps_sock_flow_entries.
+For a multi-queue device, the rps_flow_cnt for each queue might be
+configured as rps_sock_flow_entries / N, where N is the number of
+queues. So for instance, if rps_flow_entries is set to 32768 and there
+are 16 configured receive queues, rps_flow_cnt for each queue might be
+configured as 2048.
+
+
+Accelerated RFS
+===============
+
+Accelerated RFS is to RFS what RSS is to RPS: a hardware-accelerated load
+balancing mechanism that uses soft state to steer flows based on where
+the application thread consuming the packets of each flow is running.
+Accelerated RFS should perform better than RFS since packets are sent
+directly to a CPU local to the thread consuming the data. The target CPU
+will either be the same CPU where the application runs, or at least a CPU
+which is local to the application thread’s CPU in the cache hierarchy.
+
+To enable accelerated RFS, the networking stack calls the
+ndo_rx_flow_steer driver function to communicate the desired hardware
+queue for packets matching a particular flow. The network stack
+automatically calls this function every time a flow entry in
+rps_dev_flow_table is updated. The driver in turn uses a device specific
+method to program the NIC to steer the packets.
+
+The hardware queue for a flow is derived from the CPU recorded in
+rps_dev_flow_table. The stack consults a CPU to hardware queue map which
+is maintained by the NIC driver. This is an auto-generated reverse map of
+the IRQ affinity table shown by /proc/interrupts. Drivers can use
+functions in the cpu_rmap (“CPU affinity reverse map”) kernel library
+to populate the map. For each CPU, the corresponding queue in the map is
+set to be one whose processing CPU is closest in cache locality.
+
+==== Accelerated RFS Configuration
+
+Accelerated RFS is only available if the kernel is compiled with
+CONFIG_RFS_ACCEL and support is provided by the NIC device and driver.
+It also requires that ntuple filtering is enabled via ethtool. The map
+of CPU to queues is automatically deduced from the IRQ affinities
+configured for each receive queue by the driver, so no additional
+configuration should be necessary.
+
+== Suggested Configuration
+
+This technique should be enabled whenever one wants to use RFS and the
+NIC supports hardware acceleration.
+
+XPS: Transmit Packet Steering
+=============================
+
+Transmit Packet Steering is a mechanism for intelligently selecting
+which transmit queue to use when transmitting a packet on a multi-queue
+device. To accomplish this, a mapping from CPU to hardware queue(s) is
+recorded. The goal of this mapping is usually to assign queues
+exclusively to a subset of CPUs, where the transmit completions for
+these queues are processed on a CPU within this set. This choice
+provides two benefits. First, contention on the device queue lock is
+significantly reduced since fewer CPUs contend for the same queue
+(contention can be eliminated completely if each CPU has its own
+transmit queue). Secondly, cache miss rate on transmit completion is
+reduced, in particular for data cache lines that hold the sk_buff
+structures.
+
+XPS is configured per transmit queue by setting a bitmap of CPUs that
+may use that queue to transmit. The reverse mapping, from CPUs to
+transmit queues, is computed and maintained for each network device.
+When transmitting the first packet in a flow, the function
+get_xps_queue() is called to select a queue. This function uses the ID
+of the running CPU as a key into the CPU-to-queue lookup table. If the
+ID matches a single queue, that is used for transmission. If multiple
+queues match, one is selected by using the flow hash to compute an index
+into the set.
+
+The queue chosen for transmitting a particular flow is saved in the
+corresponding socket structure for the flow (e.g. a TCP connection).
+This transmit queue is used for subsequent packets sent on the flow to
+prevent out of order (ooo) packets. The choice also amortizes the cost
+of calling get_xps_queues() over all packets in the connection. To avoid
+ooo packets, the queue for a flow can subsequently only be changed if
+skb->ooo_okay is set for a packet in the flow. This flag indicates that
+there are no outstanding packets in the flow, so the transmit queue can
+change without the risk of generating out of order packets. The
+transport layer is responsible for setting ooo_okay appropriately. TCP,
+for instance, sets the flag when all data for a connection has been
+acknowledged.
+
+==== XPS Configuration
+
+XPS is only available if the kconfig symbol CONFIG_XPS is enabled (on by
+default for SMP). The functionality remains disabled until explicitly
+configured. To enable XPS, the bitmap of CPUs that may use a transmit
+queue is configured using the sysfs file entry:
+
+/sys/class/net/<dev>/queues/tx-<n>/xps_cpus
+
+== Suggested Configuration
+
+For a network device with a single transmission queue, XPS configuration
+has no effect, since there is no choice in this case. In a multi-queue
+system, XPS is preferably configured so that each CPU maps onto one queue.
+If there are as many queues as there are CPUs in the system, then each
+queue can also map onto one CPU, resulting in exclusive pairings that
+experience no contention. If there are fewer queues than CPUs, then the
+best CPUs to share a given queue are probably those that share the cache
+with the CPU that processes transmit completions for that queue
+(transmit interrupts).
+
+
+Further Information
+===================
+RPS and RFS were introduced in kernel 2.6.35. XPS was incorporated into
+2.6.38. Original patches were submitted by Tom Herbert
+(therbert@google.com)
+
+Accelerated RFS was introduced in 2.6.35. Original patches were
+submitted by Ben Hutchings (bhutchings@solarflare.com)
+
+Authors:
+Tom Herbert (therbert@google.com)
+Willem de Bruijn (willemb@google.com)
F: drivers/macintosh/
LINUX FOR POWERPC EMBEDDED MPC5XXX
-M: Grant Likely <grant.likely@secretlab.ca>
+M: Anatolij Gustschin <agust@denx.de>
L: linuxppc-dev@lists.ozlabs.org
-T: git git://git.secretlab.ca/git/linux-2.6.git
+T: git git://git.denx.de/linux-2.6-agust.git
S: Maintained
F: arch/powerpc/platforms/512x/
F: arch/powerpc/platforms/52xx/
M: Linus Torvalds <torvalds@linux-foundation.org>
L: linux-kernel@vger.kernel.org
Q: http://patchwork.kernel.org/project/LKML/list/
-T: git git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
S: Buried alive in reporters
F: *
F: */
The base address of exception vectors.
config ARM_PATCH_PHYS_VIRT
- bool "Patch physical to virtual translations at runtime (EXPERIMENTAL)"
- depends on EXPERIMENTAL
+ bool "Patch physical to virtual translations at runtime"
depends on !XIP_KERNEL && MMU
depends on !ARCH_REALVIEW || !SPARSEMEM
help
@ enable access to CP0 and CP1
XSC(mrc p15, 0, r4, c15, c1, 0)
- XSC(orr r4, r4, #0xf)
+ XSC(orr r4, r4, #0x3)
XSC(mcr p15, 0, r4, c15, c1, 0)
PJ4(mrc p15, 0, r4, c1, c0, 2)
- PJ4(orr r4, r4, #0x3)
+ PJ4(orr r4, r4, #0xf)
PJ4(mcr p15, 0, r4, c1, c0, 2)
mov r0, #0 @ nothing to load
teq r2, r3 @ next task owns it?
movne pc, lr @ no: leave Concan disabled
-1: @ flip Conan access
+1: @ flip Concan access
XSC(eor r1, r1, #0x3)
XSC(mcr p15, 0, r1, c15, c1, 0)
PJ4(eor r1, r1, #0xf)
#endif
s = find_mod_section(hdr, sechdrs, ".alt.smp.init");
if (s && !is_smp())
+#ifdef CONFIG_SMP_ON_UP
fixup_smp((void *)s->sh_addr, s->sh_size);
+#else
+ return -EINVAL;
+#endif
return 0;
}
__raw_writel(__raw_readl(CRM_BASE+0x64) | (1 << 7) | (1 << 0),
CRM_BASE + 0x64);
+ /* Clock source for gpt is ahb_div */
+ __raw_writel(__raw_readl(CRM_BASE+0x64) & ~(1 << 5), CRM_BASE + 0x64);
+
mxc_timer_init(&gpt_clk, MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), 54);
return 0;
#include <linux/input.h>
#include <linux/gpio.h>
#include <linux/delay.h>
+#include <sound/tlv320aic32x4.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
.invert = 0,
};
+static struct aic32x4_pdata visstrim_m10_aic32x4_pdata = {
+ .power_cfg = AIC32X4_PWR_MICBIAS_2075_LDOIN |
+ AIC32X4_PWR_AVDD_DVDD_WEAK_DISABLE |
+ AIC32X4_PWR_AIC32X4_LDO_ENABLE |
+ AIC32X4_PWR_CMMODE_LDOIN_RANGE_18_36 |
+ AIC32X4_PWR_CMMODE_HP_LDOIN_POWERED,
+ .micpga_routing = AIC32X4_MICPGA_ROUTE_LMIC_IN2R_10K |
+ AIC32X4_MICPGA_ROUTE_RMIC_IN1L_10K,
+ .swapdacs = false,
+};
+
static struct i2c_board_info visstrim_m10_i2c_devices[] = {
{
I2C_BOARD_INFO("pca9555", 0x20),
},
{
I2C_BOARD_INFO("tlv320aic32x4", 0x18),
+ .platform_data = &visstrim_m10_aic32x4_pdata,
}
};
#endif
};
-static void mxc_init_i2c(void)
+static void __init mxc_init_i2c(void)
{
i2c_register_board_info(1, mx31ads_i2c1_devices,
ARRAY_SIZE(mx31ads_i2c1_devices));
MX31_PIN_STXD5__STXD5,
};
-static void mxc_init_audio(void)
+static void __init mxc_init_audio(void)
{
imx31_add_imx_ssi(0, NULL);
mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi");
.portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
};
-static void lilly1131_usb_init(void)
+static void __init lilly1131_usb_init(void)
{
imx31_add_mxc_ehci_hs(1, &usbh1_pdata);
#include <mach/gpio.h>
#include <mach/pxa168.h>
#include <mach/mfp-pxa168.h>
-#include <mach/mfp-gplugd.h>
#include "common.h"
static unsigned long gplugd_pin_config[] __initdata = {
/* UART3 */
- GPIO8_UART3_SOUT,
- GPIO9_UART3_SIN,
- GPI1O_UART3_CTS,
- GPI11_UART3_RTS,
+ GPIO8_UART3_TXD,
+ GPIO9_UART3_RXD,
+ GPIO1O_UART3_CTS,
+ GPIO11_UART3_RTS,
+
+ /* USB OTG PEN */
+ GPIO18_GPIO,
/* MMC2 */
GPIO28_MMC2_CMD,
GPIO105_CI2C_SDA,
GPIO106_CI2C_SCL,
+ /* SPI NOR Flash on SSP2 */
+ GPIO107_SSP2_RXD,
+ GPIO108_SSP2_TXD,
+ GPIO110_GPIO, /* SPI_CSn */
+ GPIO111_SSP2_CLK,
+
/* Select JTAG */
GPIO109_GPIO,
"frequency\n");
} else {
gpio_direction_output(35, 1);
- gpio_free(104);
+ gpio_free(35);
}
if (unlikely(gpio_request(85, "DISP_FREQ_SEL_2"))) {
"frequency\n");
} else {
gpio_direction_output(85, 0);
- gpio_free(104);
+ gpio_free(85);
}
}
+++ /dev/null
-/*
- * linux/arch/arm/mach-mmp/include/mach/mfp-gplugd.h
- *
- * MFP definitions used in gplugD
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_MFP_GPLUGD_H
-#define __MACH_MFP_GPLUGD_H
-
-#include <plat/mfp.h>
-#include <mach/mfp.h>
-
-/* UART3 */
-#define GPIO8_UART3_SOUT MFP_CFG(GPIO8, AF2)
-#define GPIO9_UART3_SIN MFP_CFG(GPIO9, AF2)
-#define GPI1O_UART3_CTS MFP_CFG(GPIO10, AF2)
-#define GPI11_UART3_RTS MFP_CFG(GPIO11, AF2)
-
-/* MMC2 */
-#define GPIO28_MMC2_CMD MFP_CFG_DRV(GPIO28, AF6, FAST)
-#define GPIO29_MMC2_CLK MFP_CFG_DRV(GPIO29, AF6, FAST)
-#define GPIO30_MMC2_DAT0 MFP_CFG_DRV(GPIO30, AF6, FAST)
-#define GPIO31_MMC2_DAT1 MFP_CFG_DRV(GPIO31, AF6, FAST)
-#define GPIO32_MMC2_DAT2 MFP_CFG_DRV(GPIO32, AF6, FAST)
-#define GPIO33_MMC2_DAT3 MFP_CFG_DRV(GPIO33, AF6, FAST)
-
-/* I2S */
-#undef GPIO114_I2S_FRM
-#undef GPIO115_I2S_BCLK
-
-#define GPIO114_I2S_FRM MFP_CFG_DRV(GPIO114, AF1, FAST)
-#define GPIO115_I2S_BCLK MFP_CFG_DRV(GPIO115, AF1, FAST)
-#define GPIO116_I2S_TXD MFP_CFG_DRV(GPIO116, AF1, FAST)
-
-/* MMC4 */
-#define GPIO125_MMC4_DAT3 MFP_CFG_DRV(GPIO125, AF7, FAST)
-#define GPIO126_MMC4_DAT2 MFP_CFG_DRV(GPIO126, AF7, FAST)
-#define GPIO127_MMC4_DAT1 MFP_CFG_DRV(GPIO127, AF7, FAST)
-#define GPIO0_2_MMC4_DAT0 MFP_CFG_DRV(GPIO0_2, AF7, FAST)
-#define GPIO1_2_MMC4_CMD MFP_CFG_DRV(GPIO1_2, AF7, FAST)
-#define GPIO2_2_MMC4_CLK MFP_CFG_DRV(GPIO2_2, AF7, FAST)
-
-/* OTG GPIO */
-#define GPIO_USB_OTG_PEN 18
-#define GPIO_USB_OIDIR 20
-
-/* Other GPIOs are 35, 84, 85 */
-#endif /* __MACH_MFP_GPLUGD_H */
#define GPIO33_CF_nCD2 MFP_CFG(GPIO33, AF3)
/* UART */
+#define GPIO8_UART3_TXD MFP_CFG(GPIO8, AF2)
+#define GPIO9_UART3_RXD MFP_CFG(GPIO9, AF2)
+#define GPIO1O_UART3_CTS MFP_CFG(GPIO10, AF2)
+#define GPIO11_UART3_RTS MFP_CFG(GPIO11, AF2)
#define GPIO88_UART2_TXD MFP_CFG(GPIO88, AF2)
#define GPIO89_UART2_RXD MFP_CFG(GPIO89, AF2)
#define GPIO107_UART1_TXD MFP_CFG_DRV(GPIO107, AF1, FAST)
#define GPIO53_MMC1_CD MFP_CFG(GPIO53, AF1)
#define GPIO46_MMC1_WP MFP_CFG(GPIO46, AF1)
+/* MMC2 */
+#define GPIO28_MMC2_CMD MFP_CFG_DRV(GPIO28, AF6, FAST)
+#define GPIO29_MMC2_CLK MFP_CFG_DRV(GPIO29, AF6, FAST)
+#define GPIO30_MMC2_DAT0 MFP_CFG_DRV(GPIO30, AF6, FAST)
+#define GPIO31_MMC2_DAT1 MFP_CFG_DRV(GPIO31, AF6, FAST)
+#define GPIO32_MMC2_DAT2 MFP_CFG_DRV(GPIO32, AF6, FAST)
+#define GPIO33_MMC2_DAT3 MFP_CFG_DRV(GPIO33, AF6, FAST)
+
+/* MMC4 */
+#define GPIO125_MMC4_DAT3 MFP_CFG_DRV(GPIO125, AF7, FAST)
+#define GPIO126_MMC4_DAT2 MFP_CFG_DRV(GPIO126, AF7, FAST)
+#define GPIO127_MMC4_DAT1 MFP_CFG_DRV(GPIO127, AF7, FAST)
+#define GPIO0_2_MMC4_DAT0 MFP_CFG_DRV(GPIO0_2, AF7, FAST)
+#define GPIO1_2_MMC4_CMD MFP_CFG_DRV(GPIO1_2, AF7, FAST)
+#define GPIO2_2_MMC4_CLK MFP_CFG_DRV(GPIO2_2, AF7, FAST)
+
/* LCD */
#define GPIO84_LCD_CS MFP_CFG(GPIO84, AF1)
#define GPIO60_LCD_DD0 MFP_CFG(GPIO60, AF1)
#define GPIO106_CI2C_SCL MFP_CFG(GPIO106, AF1)
/* I2S */
-#define GPIO113_I2S_MCLK MFP_CFG(GPIO113,AF6)
-#define GPIO114_I2S_FRM MFP_CFG(GPIO114,AF1)
-#define GPIO115_I2S_BCLK MFP_CFG(GPIO115,AF1)
-#define GPIO116_I2S_RXD MFP_CFG(GPIO116,AF2)
-#define GPIO117_I2S_TXD MFP_CFG(GPIO117,AF2)
+#define GPIO113_I2S_MCLK MFP_CFG(GPIO113, AF6)
+#define GPIO114_I2S_FRM MFP_CFG(GPIO114, AF1)
+#define GPIO115_I2S_BCLK MFP_CFG(GPIO115, AF1)
+#define GPIO116_I2S_RXD MFP_CFG(GPIO116, AF2)
+#define GPIO116_I2S_TXD MFP_CFG(GPIO116, AF1)
+#define GPIO117_I2S_TXD MFP_CFG(GPIO117, AF2)
/* PWM */
#define GPIO96_PWM3_OUT MFP_CFG(GPIO96, AF1)
#define GPIO101_MII_MDIO MFP_CFG(GPIO101, AF5)
#define GPIO103_RX_DV MFP_CFG(GPIO103, AF5)
+/* SSP2 */
+#define GPIO107_SSP2_RXD MFP_CFG(GPIO107, AF4)
+#define GPIO108_SSP2_TXD MFP_CFG(GPIO108, AF4)
+#define GPIO111_SSP2_CLK MFP_CFG(GPIO111, AF4)
+#define GPIO112_SSP2_FRM MFP_CFG(GPIO112, AF4)
+
#endif /* __ASM_MACH_MFP_PXA168_H */
{
int delay = 100;
- __raw_writel(1, TIMERS_VIRT_BASE + TMR_CVWR(0));
+ __raw_writel(1, TIMERS_VIRT_BASE + TMR_CVWR(1));
while (delay--)
cpu_relax();
- return __raw_readl(TIMERS_VIRT_BASE + TMR_CVWR(0));
+ return __raw_readl(TIMERS_VIRT_BASE + TMR_CVWR(1));
}
unsigned long long notrace sched_clock(void)
{
struct clock_event_device *c = dev_id;
- /* disable and clear pending interrupt status */
- __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(0));
- __raw_writel(0x1, TIMERS_VIRT_BASE + TMR_ICR(0));
+ /*
+ * Clear pending interrupt status.
+ */
+ __raw_writel(0x01, TIMERS_VIRT_BASE + TMR_ICR(0));
+
+ /*
+ * Disable timer 0.
+ */
+ __raw_writel(0x02, TIMERS_VIRT_BASE + TMR_CER);
+
c->event_handler(c);
+
return IRQ_HANDLED;
}
static int timer_set_next_event(unsigned long delta,
struct clock_event_device *dev)
{
- unsigned long flags, next;
+ unsigned long flags;
local_irq_save(flags);
- /* clear pending interrupt status and enable */
+ /*
+ * Disable timer 0.
+ */
+ __raw_writel(0x02, TIMERS_VIRT_BASE + TMR_CER);
+
+ /*
+ * Clear and enable timer match 0 interrupt.
+ */
__raw_writel(0x01, TIMERS_VIRT_BASE + TMR_ICR(0));
__raw_writel(0x01, TIMERS_VIRT_BASE + TMR_IER(0));
- next = timer_read() + delta;
- __raw_writel(next, TIMERS_VIRT_BASE + TMR_TN_MM(0, 0));
+ /*
+ * Setup new clockevent timer value.
+ */
+ __raw_writel(delta - 1, TIMERS_VIRT_BASE + TMR_TN_MM(0, 0));
+
+ /*
+ * Enable timer 0.
+ */
+ __raw_writel(0x03, TIMERS_VIRT_BASE + TMR_CER);
local_irq_restore(flags);
+
return 0;
}
static void __init timer_config(void)
{
uint32_t ccr = __raw_readl(TIMERS_VIRT_BASE + TMR_CCR);
- uint32_t cer = __raw_readl(TIMERS_VIRT_BASE + TMR_CER);
- uint32_t cmr = __raw_readl(TIMERS_VIRT_BASE + TMR_CMR);
- __raw_writel(cer & ~0x1, TIMERS_VIRT_BASE + TMR_CER); /* disable */
+ __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_CER); /* disable */
- ccr &= (cpu_is_mmp2()) ? TMR_CCR_CS_0(0) : TMR_CCR_CS_0(3);
+ ccr &= (cpu_is_mmp2()) ? (TMR_CCR_CS_0(0) | TMR_CCR_CS_1(0)) :
+ (TMR_CCR_CS_0(3) | TMR_CCR_CS_1(3));
__raw_writel(ccr, TIMERS_VIRT_BASE + TMR_CCR);
- /* free-running mode */
- __raw_writel(cmr | 0x01, TIMERS_VIRT_BASE + TMR_CMR);
+ /* set timer 0 to periodic mode, and timer 1 to free-running mode */
+ __raw_writel(0x2, TIMERS_VIRT_BASE + TMR_CMR);
- __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_PLCR(0)); /* free-running */
+ __raw_writel(0x1, TIMERS_VIRT_BASE + TMR_PLCR(0)); /* periodic */
__raw_writel(0x7, TIMERS_VIRT_BASE + TMR_ICR(0)); /* clear status */
__raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(0));
- /* enable timer counter */
- __raw_writel(cer | 0x01, TIMERS_VIRT_BASE + TMR_CER);
+ __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_PLCR(1)); /* free-running */
+ __raw_writel(0x7, TIMERS_VIRT_BASE + TMR_ICR(1)); /* clear status */
+ __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(1));
+
+ /* enable timer 1 counter */
+ __raw_writel(0x2, TIMERS_VIRT_BASE + TMR_CER);
}
static struct irqaction timer_irq = {
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x2000000),
- .irq = irq_to_gpio(CPUIMX51_QUARTD_GPIO),
+ .irq = gpio_to_irq(CPUIMX51_QUARTD_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
ARRAY_SIZE(mx51babbage_pads));
imx51_add_imx_uart(0, &uart_pdata);
- imx51_add_imx_uart(1, &uart_pdata);
+ imx51_add_imx_uart(1, NULL);
imx51_add_imx_uart(2, &uart_pdata);
babbage_fec_reset();
gpio_request(EFIKAMX_PCBID2, "pcbid2");
gpio_direction_input(EFIKAMX_PCBID2);
- id = gpio_get_value(EFIKAMX_PCBID0);
- id |= gpio_get_value(EFIKAMX_PCBID1) << 1;
- id |= gpio_get_value(EFIKAMX_PCBID2) << 2;
+ id = gpio_get_value(EFIKAMX_PCBID0) ? 1 : 0;
+ id |= (gpio_get_value(EFIKAMX_PCBID1) ? 1 : 0) << 1;
+ id |= (gpio_get_value(EFIKAMX_PCBID2) ? 1 : 0) << 2;
switch (id) {
case 7:
{
.code = KEY_POWER,
.gpio = EFIKASB_PWRKEY,
- .type = EV_PWR,
+ .type = EV_KEY,
.desc = "Power Button",
.wakeup = 1,
- .debounce_interval = 10, /* ms */
+ .active_low = 1,
},
{
.code = SW_LID,
.gpio = EFIKASB_LID,
.type = EV_SW,
.desc = "Lid Switch",
+ .active_low = 1,
},
{
- /* SW_RFKILLALL vs KEY_RFKILL ? */
- .code = SW_RFKILL_ALL,
+ .code = KEY_RFKILL,
.gpio = EFIKASB_RFKILL,
- .type = EV_SW,
+ .type = EV_KEY,
.desc = "rfkill",
+ .active_low = 1,
},
};
gpio_request(EFIKASB_PCBID1, "pcb id1");
gpio_direction_input(EFIKASB_PCBID1);
- id = gpio_get_value(EFIKASB_PCBID0);
- id |= gpio_get_value(EFIKASB_PCBID1) << 1;
+ id = gpio_get_value(EFIKASB_PCBID0) ? 1 : 0;
+ id |= (gpio_get_value(EFIKASB_PCBID1) ? 1 : 0) << 1;
switch (id) {
default:
int i = 0;
pllbase = _get_pll_base(clk);
- reg = __raw_readl(pllbase + MXC_PLL_DP_CTL) | MXC_PLL_DP_CTL_UPEN;
+ reg = __raw_readl(pllbase + MXC_PLL_DP_CTL);
+ if (reg & MXC_PLL_DP_CTL_UPEN)
+ return 0;
+
+ reg |= MXC_PLL_DP_CTL_UPEN;
__raw_writel(reg, pllbase + MXC_PLL_DP_CTL);
/* Wait for lock */
mdelay(10);
- return mx51_initialize_usb_hw(0, MXC_EHCI_ITC_NO_THRESHOLD);
+ return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_ITC_NO_THRESHOLD);
}
static struct mxc_usbh_platform_data usbh1_config = {
default y
select AEABI
select REGULATOR
- select PM
select PM_RUNTIME
select VFP
select NEON if ARCH_OMAP3 || ARCH_OMAP4
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
-#else
-#define board_mux NULL
#endif
static void __init am3517_crane_init_early(void)
/* Custom OPP enabled for all xM versions */
if (cpu_is_omap3630()) {
- struct omap_hwmod *mh = omap_hwmod_lookup("mpu");
- struct omap_hwmod *dh = omap_hwmod_lookup("iva");
- struct device *dev;
+ struct device *mpu_dev, *iva_dev;
- if (!mh || !dh) {
+ mpu_dev = omap2_get_mpuss_device();
+ iva_dev = omap2_get_iva_device();
+
+ if (!mpu_dev || !iva_dev) {
pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
- __func__, mh, dh);
+ __func__, mpu_dev, iva_dev);
return;
}
/* Enable MPU 1GHz and lower opps */
- dev = &mh->od->pdev.dev;
- r = opp_enable(dev, 800000000);
+ r = opp_enable(mpu_dev, 800000000);
/* TODO: MPU 1GHz needs SR and ABB */
/* Enable IVA 800MHz and lower opps */
- dev = &dh->od->pdev.dev;
- r |= opp_enable(dev, 660000000);
+ r |= opp_enable(iva_dev, 660000000);
/* TODO: DSP 800MHz needs SR and ABB */
if (r) {
pr_err("%s: failed to enable higher opp %d\n",
* Cleanup - disable the higher freqs - we dont care
* about the results
*/
- dev = &mh->od->pdev.dev;
- opp_disable(dev, 800000000);
- dev = &dh->od->pdev.dev;
- opp_disable(dev, 660000000);
+ opp_disable(mpu_dev, 800000000);
+ opp_disable(iva_dev, 660000000);
}
}
return;
extern void omap4_cminst_clkdm_force_wakeup(u8 part, s16 inst, u16 cdoffs);
extern int omap4_cminst_wait_module_ready(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs);
-extern int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs);
+
+# ifdef CONFIG_ARCH_OMAP4
+extern int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs,
+ u16 clkctrl_offs);
extern void omap4_cminst_module_enable(u8 mode, u8 part, u16 inst, s16 cdoffs,
u16 clkctrl_offs);
extern void omap4_cminst_module_disable(u8 part, u16 inst, s16 cdoffs,
u16 clkctrl_offs);
+# else
+
+static inline int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs,
+ u16 clkctrl_offs)
+{
+ return 0;
+}
+
+static inline void omap4_cminst_module_enable(u8 mode, u8 part, u16 inst,
+ s16 cdoffs, u16 clkctrl_offs)
+{
+}
+
+static inline void omap4_cminst_module_disable(u8 part, u16 inst, s16 cdoffs,
+ u16 clkctrl_offs)
+{
+}
+
+# endif
+
/*
* In an ideal world, we would not export these low-level functions,
* but this will probably take some time to fix properly
if (!omap_mux_options)
return;
- options = kmalloc(strlen(omap_mux_options) + 1, GFP_KERNEL);
+ options = kstrdup(omap_mux_options, GFP_KERNEL);
if (!options)
return;
- strcpy(options, omap_mux_options);
next_opt = options;
while ((token = strsep(&next_opt, ",")) != NULL) {
for (i = 0; i < OMAP_MUX_NR_MODES; i++) {
if (src->muxnames[i]) {
- dst->muxnames[i] =
- kmalloc(strlen(src->muxnames[i]) + 1,
- GFP_KERNEL);
+ dst->muxnames[i] = kstrdup(src->muxnames[i],
+ GFP_KERNEL);
if (!dst->muxnames[i])
goto free;
- strcpy(dst->muxnames[i], src->muxnames[i]);
}
}
#ifdef CONFIG_DEBUG_FS
for (i = 0; i < OMAP_MUX_NR_SIDES; i++) {
if (src->balls[i]) {
- dst->balls[i] =
- kmalloc(strlen(src->balls[i]) + 1,
- GFP_KERNEL);
+ dst->balls[i] = kstrdup(src->balls[i], GFP_KERNEL);
if (!dst->balls[i])
goto free;
- strcpy(dst->balls[i], src->balls[i]);
}
}
#endif
sr_v2_disable(sr);
}
- pm_runtime_put_sync(&sr->pdev->dev);
+ pm_runtime_put_sync_suspend(&sr->pdev->dev);
}
/**
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
pm_runtime_enable(&pdev->dev);
+ pm_runtime_irq_safe(&pdev->dev);
sr_info->pdev = pdev;
sr_info->srid = pdev->id;
pr_info("OMAP clocksource: GPTIMER%d at %lu Hz\n",
gptimer_id, clksrc.rate);
- __omap_dm_timer_load_start(clksrc.io_base, OMAP_TIMER_CTRL_ST, 0, 1);
+ __omap_dm_timer_load_start(clksrc.io_base,
+ OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR, 0, 1);
init_sched_clock(&cd, dmtimer_update_sched_clock, 32, clksrc.rate);
if (clocksource_register_hz(&clocksource_gpt, clksrc.rate))
omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
}
-static struct twl4030_usb_data omap4_usb_pdata = {
- .phy_init = omap4430_phy_init,
- .phy_exit = omap4430_phy_exit,
- .phy_power = omap4430_phy_power,
- .phy_set_clock = omap4430_phy_set_clk,
- .phy_suspend = omap4430_phy_suspend,
-};
-
+#if defined(CONFIG_ARCH_OMAP3)
static struct twl4030_usb_data omap3_usb_pdata = {
.usb_mode = T2_USB_MODE_ULPI,
};
.consumer_supplies = omap3_vpll2_supplies,
};
+void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
+ u32 pdata_flags, u32 regulators_flags)
+{
+ if (!pmic_data->irq_base)
+ pmic_data->irq_base = TWL4030_IRQ_BASE;
+ if (!pmic_data->irq_end)
+ pmic_data->irq_end = TWL4030_IRQ_END;
+
+ /* Common platform data configurations */
+ if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
+ pmic_data->usb = &omap3_usb_pdata;
+
+ if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci)
+ pmic_data->bci = &omap3_bci_pdata;
+
+ if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc)
+ pmic_data->madc = &omap3_madc_pdata;
+
+ if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio)
+ pmic_data->audio = &omap3_audio_pdata;
+
+ /* Common regulator configurations */
+ if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
+ pmic_data->vdac = &omap3_vdac_idata;
+
+ if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2)
+ pmic_data->vpll2 = &omap3_vpll2_idata;
+}
+#endif /* CONFIG_ARCH_OMAP3 */
+
+#if defined(CONFIG_ARCH_OMAP4)
+static struct twl4030_usb_data omap4_usb_pdata = {
+ .phy_init = omap4430_phy_init,
+ .phy_exit = omap4430_phy_exit,
+ .phy_power = omap4430_phy_power,
+ .phy_set_clock = omap4430_phy_set_clk,
+ .phy_suspend = omap4430_phy_suspend,
+};
+
static struct regulator_init_data omap4_vdac_idata = {
.constraints = {
.min_uV = 1800000,
!pmic_data->clk32kg)
pmic_data->clk32kg = &omap4_clk32kg_idata;
}
-
-void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags)
-{
- if (!pmic_data->irq_base)
- pmic_data->irq_base = TWL4030_IRQ_BASE;
- if (!pmic_data->irq_end)
- pmic_data->irq_end = TWL4030_IRQ_END;
-
- /* Common platform data configurations */
- if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
- pmic_data->usb = &omap3_usb_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci)
- pmic_data->bci = &omap3_bci_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc)
- pmic_data->madc = &omap3_madc_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio)
- pmic_data->audio = &omap3_audio_pdata;
-
- /* Common regulator configurations */
- if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
- pmic_data->vdac = &omap3_vdac_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2)
- pmic_data->vpll2 = &omap3_vpll2_idata;
-}
+#endif /* CONFIG_ARCH_OMAP4 */
#include <plat/iic.h>
#include <plat/pm.h>
-#include <sound/wm8915.h>
+#include <sound/wm8996.h>
#include <sound/wm8962.h>
#include <sound/wm9081.h>
.disable_touch = true,
};
-static struct wm8915_retune_mobile_config wm8915_retune[] = {
+static struct wm8996_retune_mobile_config wm8996_retune[] = {
{
.name = "Sub LPF",
.rate = 48000,
},
};
-static struct wm8915_pdata wm8915_pdata __initdata = {
+static struct wm8996_pdata wm8996_pdata __initdata = {
.ldo_ena = S3C64XX_GPN(7),
.gpio_base = CODEC_GPIO_BASE,
.micdet_def = 1,
- .inl_mode = WM8915_DIFFERRENTIAL_1,
- .inr_mode = WM8915_DIFFERRENTIAL_1,
+ .inl_mode = WM8996_DIFFERRENTIAL_1,
+ .inr_mode = WM8996_DIFFERRENTIAL_1,
.irq_flags = IRQF_TRIGGER_RISING,
0x020e, /* GPIO5 == CLKOUT */
},
- .retune_mobile_cfgs = wm8915_retune,
- .num_retune_mobile_cfgs = ARRAY_SIZE(wm8915_retune),
+ .retune_mobile_cfgs = wm8996_retune,
+ .num_retune_mobile_cfgs = ARRAY_SIZE(wm8996_retune),
};
static struct wm8962_pdata wm8962_pdata __initdata = {
.platform_data = &glenfarclas_pmic_pdata },
{ I2C_BOARD_INFO("wm1250-ev1", 0x27) },
- { I2C_BOARD_INFO("wm8915", 0x1a),
- .platform_data = &wm8915_pdata,
+ { I2C_BOARD_INFO("wm8996", 0x1a),
+ .platform_data = &wm8996_pdata,
.irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2,
},
{ I2C_BOARD_INFO("wm9081", 0x6c),
#include <asm/mach-types.h>
#include <mach/nanoengine.h>
+#include <mach/hardware.h>
static DEFINE_SPINLOCK(nano_lock);
#include <linux/sched.h>
#include <linux/uaccess.h>
+#include <asm/system.h>
#include <asm/unaligned.h>
#include "fault.h"
"signal+warn"
};
+/* Return true if and only if the ARMv6 unaligned access model is in use. */
+static bool cpu_is_v6_unaligned(void)
+{
+ return cpu_architecture() >= CPU_ARCH_ARMv6 && (cr_alignment & CR_U);
+}
+
+static int safe_usermode(int new_usermode, bool warn)
+{
+ /*
+ * ARMv6 and later CPUs can perform unaligned accesses for
+ * most single load and store instructions up to word size.
+ * LDM, STM, LDRD and STRD still need to be handled.
+ *
+ * Ignoring the alignment fault is not an option on these
+ * CPUs since we spin re-faulting the instruction without
+ * making any progress.
+ */
+ if (cpu_is_v6_unaligned() && !(new_usermode & (UM_FIXUP | UM_SIGNAL))) {
+ new_usermode |= UM_FIXUP;
+
+ if (warn)
+ printk(KERN_WARNING "alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode.\n");
+ }
+
+ return new_usermode;
+}
+
static int alignment_proc_show(struct seq_file *m, void *v)
{
seq_printf(m, "User:\t\t%lu\n", ai_user);
if (get_user(mode, buffer))
return -EFAULT;
if (mode >= '0' && mode <= '5')
- ai_usermode = mode - '0';
+ ai_usermode = safe_usermode(mode - '0', true);
}
return count;
}
if (ai_usermode & UM_FIXUP)
goto fixup;
- if (ai_usermode & UM_SIGNAL)
- force_sig(SIGBUS, current);
- else {
+ if (ai_usermode & UM_SIGNAL) {
+ siginfo_t si;
+
+ si.si_signo = SIGBUS;
+ si.si_errno = 0;
+ si.si_code = BUS_ADRALN;
+ si.si_addr = (void __user *)addr;
+
+ force_sig_info(si.si_signo, &si, current);
+ } else {
/*
* We're about to disable the alignment trap and return to
* user space. But if an interrupt occurs before actually
return -ENOMEM;
#endif
- /*
- * ARMv6 and later CPUs can perform unaligned accesses for
- * most single load and store instructions up to word size.
- * LDM, STM, LDRD and STRD still need to be handled.
- *
- * Ignoring the alignment fault is not an option on these
- * CPUs since we spin re-faulting the instruction without
- * making any progress.
- */
- if (cpu_architecture() >= CPU_ARCH_ARMv6 && (cr_alignment & CR_U)) {
+ if (cpu_is_v6_unaligned()) {
cr_alignment &= ~CR_A;
cr_no_alignment &= ~CR_A;
set_cr(cr_alignment);
- ai_usermode = UM_FIXUP;
+ ai_usermode = safe_usermode(ai_usermode, false);
}
hook_fault_code(1, do_alignment, SIGBUS, BUS_ADRALN,
static inline void poison_init_mem(void *s, size_t count)
{
u32 *p = (u32 *)s;
- while ((count = count - 4))
+ for (; count != 0; count -= 4)
*p++ = 0xe7fddef0;
}
.long 0x41009460
.long 0xff00fff0
.long 0
+ .long 0
b __arm946_setup
.long cpu_arch_name
.long cpu_elf_name
.long arm946_processor_functions
.long 0
.long 0
- .long arm940_cache_fns
+ .long arm946_cache_fns
.size __arm946_proc_info, . - __arm946_proc_info
#define UART_PADDR MX51_UART1_BASE_ADDR
#endif
+/* iMX50/53 have same addresses, but not iMX51 */
+#if defined(CONFIG_SOC_IMX50) || defined(CONFIG_SOC_IMX53)
+#ifdef UART_PADDR
+#error "CONFIG_DEBUG_LL is incompatible with multiple archs"
+#endif
+#define UART_PADDR MX53_UART1_BASE_ADDR
+#endif
+
#define UART_VADDR IMX_IO_ADDRESS(UART_PADDR)
.macro addruart, rp, rv
#define MX53_SDHC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_HIGH | \
PAD_CTL_SRE_FAST)
+#define PAD_CTRL_I2C (PAD_CTL_SRE_FAST | PAD_CTL_ODE | PAD_CTL_PKE | \
+ PAD_CTL_PUE | PAD_CTL_DSE_HIGH | PAD_CTL_PUS_100K_UP \
+ | PAD_CTL_HYS)
#define _MX53_PAD_GPIO_19__KPP_COL_5 IOMUX_PAD(0x348, 0x20, 0, 0x840, 0, 0)
#define _MX53_PAD_GPIO_19__GPIO4_5 IOMUX_PAD(0x348, 0x20, 1, 0x0, 0, 0)
#define MX53_PAD_KEY_COL3__GPIO4_12 (_MX53_PAD_KEY_COL3__GPIO4_12 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_COL3__USBOH3_H2_DP (_MX53_PAD_KEY_COL3__USBOH3_H2_DP | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_COL3__SPDIF_IN1 (_MX53_PAD_KEY_COL3__SPDIF_IN1 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_KEY_COL3__I2C2_SCL (_MX53_PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_KEY_COL3__I2C2_SCL (_MX53_PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_KEY_COL3__ECSPI1_SS3 (_MX53_PAD_KEY_COL3__ECSPI1_SS3 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_COL3__FEC_CRS (_MX53_PAD_KEY_COL3__FEC_CRS | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_COL3__USBPHY1_SIECLOCK (_MX53_PAD_KEY_COL3__USBPHY1_SIECLOCK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_ROW3__GPIO4_13 (_MX53_PAD_KEY_ROW3__GPIO4_13 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_ROW3__USBOH3_H2_DM (_MX53_PAD_KEY_ROW3__USBOH3_H2_DM | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_ROW3__CCM_ASRC_EXT_CLK (_MX53_PAD_KEY_ROW3__CCM_ASRC_EXT_CLK | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_KEY_ROW3__I2C2_SDA (_MX53_PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_KEY_ROW3__I2C2_SDA (_MX53_PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_KEY_ROW3__OSC32K_32K_OUT (_MX53_PAD_KEY_ROW3__OSC32K_32K_OUT | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_ROW3__CCM_PLL4_BYP (_MX53_PAD_KEY_ROW3__CCM_PLL4_BYP | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_KEY_ROW3__USBPHY1_LINESTATE_0 (_MX53_PAD_KEY_ROW3__USBPHY1_LINESTATE_0 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT8__KPP_COL_7 (_MX53_PAD_CSI0_DAT8__KPP_COL_7 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT8__ECSPI2_SCLK (_MX53_PAD_CSI0_DAT8__ECSPI2_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC (_MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_CSI0_DAT8__I2C1_SDA (_MX53_PAD_CSI0_DAT8__I2C1_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_CSI0_DAT8__I2C1_SDA (_MX53_PAD_CSI0_DAT8__I2C1_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_CSI0_DAT8__EMI_EMI_DEBUG_37 (_MX53_PAD_CSI0_DAT8__EMI_EMI_DEBUG_37 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT8__TPIU_TRACE_5 (_MX53_PAD_CSI0_DAT8__TPIU_TRACE_5 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT9__IPU_CSI0_D_9 (_MX53_PAD_CSI0_DAT9__IPU_CSI0_D_9 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT9__KPP_ROW_7 (_MX53_PAD_CSI0_DAT9__KPP_ROW_7 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT9__ECSPI2_MOSI (_MX53_PAD_CSI0_DAT9__ECSPI2_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT9__USBOH3_USBH3_PWR (_MX53_PAD_CSI0_DAT9__USBOH3_USBH3_PWR | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_CSI0_DAT9__I2C1_SCL (_MX53_PAD_CSI0_DAT9__I2C1_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_CSI0_DAT9__I2C1_SCL (_MX53_PAD_CSI0_DAT9__I2C1_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_CSI0_DAT9__EMI_EMI_DEBUG_38 (_MX53_PAD_CSI0_DAT9__EMI_EMI_DEBUG_38 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT9__TPIU_TRACE_6 (_MX53_PAD_CSI0_DAT9__TPIU_TRACE_6 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_CSI0_DAT10__IPU_CSI0_D_10 (_MX53_PAD_CSI0_DAT10__IPU_CSI0_D_10 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_EB2__CCM_DI1_EXT_CLK (_MX53_PAD_EIM_EB2__CCM_DI1_EXT_CLK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_EB2__IPU_SER_DISP1_CS (_MX53_PAD_EIM_EB2__IPU_SER_DISP1_CS | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_EB2__ECSPI1_SS0 (_MX53_PAD_EIM_EB2__ECSPI1_SS0 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_EB2__I2C2_SCL (_MX53_PAD_EIM_EB2__I2C2_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_EB2__I2C2_SCL (_MX53_PAD_EIM_EB2__I2C2_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D16__EMI_WEIM_D_16 (_MX53_PAD_EIM_D16__EMI_WEIM_D_16 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D16__GPIO3_16 (_MX53_PAD_EIM_D16__GPIO3_16 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D16__IPU_DI0_PIN5 (_MX53_PAD_EIM_D16__IPU_DI0_PIN5 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D16__IPU_DISPB1_SER_CLK (_MX53_PAD_EIM_D16__IPU_DISPB1_SER_CLK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D16__ECSPI1_SCLK (_MX53_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_D16__I2C2_SDA (_MX53_PAD_EIM_D16__I2C2_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_D16__I2C2_SDA (_MX53_PAD_EIM_D16__I2C2_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D17__EMI_WEIM_D_17 (_MX53_PAD_EIM_D17__EMI_WEIM_D_17 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D17__GPIO3_17 (_MX53_PAD_EIM_D17__GPIO3_17 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D17__IPU_DI0_PIN6 (_MX53_PAD_EIM_D17__IPU_DI0_PIN6 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D17__IPU_DISPB1_SER_DIN (_MX53_PAD_EIM_D17__IPU_DISPB1_SER_DIN | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D17__ECSPI1_MISO (_MX53_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_D17__I2C3_SCL (_MX53_PAD_EIM_D17__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_D17__I2C3_SCL (_MX53_PAD_EIM_D17__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D18__EMI_WEIM_D_18 (_MX53_PAD_EIM_D18__EMI_WEIM_D_18 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D18__GPIO3_18 (_MX53_PAD_EIM_D18__GPIO3_18 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D18__IPU_DI0_PIN7 (_MX53_PAD_EIM_D18__IPU_DI0_PIN7 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D18__IPU_DISPB1_SER_DIO (_MX53_PAD_EIM_D18__IPU_DISPB1_SER_DIO | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D18__ECSPI1_MOSI (_MX53_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_D18__I2C3_SDA (_MX53_PAD_EIM_D18__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_D18__I2C3_SDA (_MX53_PAD_EIM_D18__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D18__IPU_DI1_D0_CS (_MX53_PAD_EIM_D18__IPU_DI1_D0_CS | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D19__EMI_WEIM_D_19 (_MX53_PAD_EIM_D19__EMI_WEIM_D_19 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D19__GPIO3_19 (_MX53_PAD_EIM_D19__GPIO3_19 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D21__IPU_DI0_PIN17 (_MX53_PAD_EIM_D21__IPU_DI0_PIN17 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK (_MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D21__CSPI_SCLK (_MX53_PAD_EIM_D21__CSPI_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_D21__I2C1_SCL (_MX53_PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_D21__I2C1_SCL (_MX53_PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D21__USBOH3_USBOTG_OC (_MX53_PAD_EIM_D21__USBOH3_USBOTG_OC | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D22__EMI_WEIM_D_22 (_MX53_PAD_EIM_D22__EMI_WEIM_D_22 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D22__GPIO3_22 (_MX53_PAD_EIM_D22__GPIO3_22 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D28__UART2_CTS (_MX53_PAD_EIM_D28__UART2_CTS | MUX_PAD_CTRL(MX53_UART_PAD_CTRL))
#define MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO (_MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D28__CSPI_MOSI (_MX53_PAD_EIM_D28__CSPI_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_EIM_D28__I2C1_SDA (_MX53_PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_EIM_D28__I2C1_SDA (_MX53_PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_EIM_D28__IPU_EXT_TRIG (_MX53_PAD_EIM_D28__IPU_EXT_TRIG | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D28__IPU_DI0_PIN13 (_MX53_PAD_EIM_D28__IPU_DI0_PIN13 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_EIM_D29__EMI_WEIM_D_29 (_MX53_PAD_EIM_D29__EMI_WEIM_D_29 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_9__SCC_FAIL_STATE (_MX53_PAD_GPIO_9__SCC_FAIL_STATE | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_3__ESAI1_HCKR (_MX53_PAD_GPIO_3__ESAI1_HCKR | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_3__GPIO1_3 (_MX53_PAD_GPIO_3__GPIO1_3 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_GPIO_3__I2C3_SCL (_MX53_PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_GPIO_3__I2C3_SCL (_MX53_PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_GPIO_3__DPLLIP1_TOG_EN (_MX53_PAD_GPIO_3__DPLLIP1_TOG_EN | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_3__CCM_CLKO2 (_MX53_PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_3__OBSERVE_MUX_OBSRV_INT_OUT0 (_MX53_PAD_GPIO_3__OBSERVE_MUX_OBSRV_INT_OUT0 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_3__MLB_MLBCLK (_MX53_PAD_GPIO_3__MLB_MLBCLK | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_6__ESAI1_SCKT (_MX53_PAD_GPIO_6__ESAI1_SCKT | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_6__GPIO1_6 (_MX53_PAD_GPIO_6__GPIO1_6 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_GPIO_6__I2C3_SDA (_MX53_PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_GPIO_6__I2C3_SDA (_MX53_PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_GPIO_6__CCM_CCM_OUT_0 (_MX53_PAD_GPIO_6__CCM_CCM_OUT_0 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_6__CSU_CSU_INT_DEB (_MX53_PAD_GPIO_6__CSU_CSU_INT_DEB | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_6__OBSERVE_MUX_OBSRV_INT_OUT1 (_MX53_PAD_GPIO_6__OBSERVE_MUX_OBSRV_INT_OUT1 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_5__CCM_CLKO (_MX53_PAD_GPIO_5__CCM_CLKO | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_5__CSU_CSU_ALARM_AUT_2 (_MX53_PAD_GPIO_5__CSU_CSU_ALARM_AUT_2 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_5__OBSERVE_MUX_OBSRV_INT_OUT4 (_MX53_PAD_GPIO_5__OBSERVE_MUX_OBSRV_INT_OUT4 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_GPIO_5__I2C3_SCL (_MX53_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_GPIO_5__I2C3_SCL (_MX53_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_GPIO_5__CCM_PLL1_BYP (_MX53_PAD_GPIO_5__CCM_PLL1_BYP | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_7__ESAI1_TX4_RX1 (_MX53_PAD_GPIO_7__ESAI1_TX4_RX1 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_7__GPIO1_7 (_MX53_PAD_GPIO_7__GPIO1_7 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_16__TZIC_PWRFAIL_INT (_MX53_PAD_GPIO_16__TZIC_PWRFAIL_INT | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_16__RTC_CE_RTC_EXT_TRIG1 (_MX53_PAD_GPIO_16__RTC_CE_RTC_EXT_TRIG1 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_16__SPDIF_IN1 (_MX53_PAD_GPIO_16__SPDIF_IN1 | MUX_PAD_CTRL(NO_PAD_CTRL))
-#define MX53_PAD_GPIO_16__I2C3_SDA (_MX53_PAD_GPIO_16__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL))
+#define MX53_PAD_GPIO_16__I2C3_SDA (_MX53_PAD_GPIO_16__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C))
#define MX53_PAD_GPIO_16__SJC_DE_B (_MX53_PAD_GPIO_16__SJC_DE_B | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_17__ESAI1_TX0 (_MX53_PAD_GPIO_17__ESAI1_TX0 | MUX_PAD_CTRL(NO_PAD_CTRL))
#define MX53_PAD_GPIO_17__GPIO7_12 (_MX53_PAD_GPIO_17__GPIO7_12 | MUX_PAD_CTRL(NO_PAD_CTRL))
bool "TI OMAP1"
select CLKDEV_LOOKUP
select CLKSRC_MMIO
+ select GENERIC_IRQ_CHIP
help
"Systems based on omap7xx, omap15xx or omap16xx"
#define OMAP36XX_DMA_UART4_TX 81 /* S_DMA_80 */
#define OMAP36XX_DMA_UART4_RX 82 /* S_DMA_81 */
+
+/* Only for AM35xx */
+#define AM35XX_DMA_UART4_TX 54
+#define AM35XX_DMA_UART4_RX 55
+
/*----------------------------------------------------------------------------*/
#define OMAP1_DMA_TOUT_IRQ (1 << 0)
#define INT_35XX_EMAC_C0_TX_PULSE_IRQ 69
#define INT_35XX_EMAC_C0_MISC_PULSE_IRQ 70
#define INT_35XX_USBOTG_IRQ 71
+#define INT_35XX_UART4 84
#define INT_35XX_CCDC_VD0_IRQ 88
#define INT_35XX_CCDC_VD1_IRQ 92
#define INT_35XX_CCDC_VD2_IRQ 93
#define TI816X_UART2_BASE 0x48022000
#define TI816X_UART3_BASE 0x48024000
+/* AM3505/3517 UART4 */
+#define AM35XX_UART4_BASE 0x4809E000 /* Only on AM3505/3517 */
+
/* External port on Zoom2/3 */
#define ZOOM_UART_BASE 0x10000000
#define ZOOM_UART_VIRT 0xfa400000
{
unsigned int i;
struct scatterlist *sg;
- void *va;
-
- va = phys_to_virt(pa);
for_each_sg(sgt->sgl, sg, sgt->nents, i) {
unsigned bytes;
uemd MACH_UEMD UEMD 3281
ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282
rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283
-nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284
+encore MACH_ENCORE ENCORE 3284
hkdkc100 MACH_HKDKC100 HKDKC100 3285
ts42xx MACH_TS42XX TS42XX 3286
aebl MACH_AEBL AEBL 3287
asm goto("1:\n\t"
"nop\n\t"
".pushsection __jump_table, \"aw\"\n\t"
- ".align 4\n\t"
JUMP_ENTRY_TYPE "1b, %l[l_yes], %c0\n\t"
".popsection \n\t"
: : "i" (key) : : l_yes);
jump_label_t code;
jump_label_t target;
jump_label_t key;
- jump_label_t pad;
};
#endif /* _ASM_POWERPC_JUMP_LABEL_H */
#include <asm/page.h>
-/*
- * If CONFIG_RELOCATABLE is enabled we can place the kdump kernel anywhere.
- * To keep enough space in the RMO for the first stage kernel on 64bit, we
- * place it at 64MB. If CONFIG_RELOCATABLE is not enabled we must place
- * the second stage at 32MB.
- */
-#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_PPC64)
-#define KDUMP_KERNELBASE 0x4000000
-#else
#define KDUMP_KERNELBASE 0x2000000
-#endif
/* How many bytes to reserve at zero for kdump. The reserve limit should
* be greater or equal to the trampoline's end address.
#define PV_970 0x0039
#define PV_POWER5 0x003A
#define PV_POWER5p 0x003B
-#define PV_POWER7 0x003F
#define PV_970FX 0x003C
#define PV_POWER6 0x003E
#define PV_POWER7 0x003F
#define mtmsrd(v) __mtmsrd((v), 0)
#define mtmsr(v) mtmsrd(v)
#else
-#define mtmsr(v) asm volatile("mtmsr %0" : : "r" (v) : "memory")
+#define mtmsr(v) asm volatile("mtmsr %0" : \
+ : "r" ((unsigned long)(v)) \
+ : "memory")
#endif
#define mfspr(rn) ({unsigned long rval; \
asm volatile("mfspr %0," __stringify(rn) \
: "=r" (rval)); rval;})
-#define mtspr(rn, v) asm volatile("mtspr " __stringify(rn) ",%0" : : "r" (v)\
+#define mtspr(rn, v) asm volatile("mtspr " __stringify(rn) ",%0" : \
+ : "r" ((unsigned long)(v)) \
: "memory")
#ifdef __powerpc64__
static struct cpu_spec the_cpu_spec;
-static void __init setup_cpu_spec(unsigned long offset, struct cpu_spec *s)
+static struct cpu_spec * __init setup_cpu_spec(unsigned long offset,
+ struct cpu_spec *s)
{
struct cpu_spec *t = &the_cpu_spec;
struct cpu_spec old;
t->cpu_setup(offset, t);
}
#endif /* CONFIG_PPC64 || CONFIG_BOOKE */
+
+ return t;
}
struct cpu_spec * __init identify_cpu(unsigned long offset, unsigned int pvr)
s = PTRRELOC(s);
for (i = 0; i < ARRAY_SIZE(cpu_specs); i++,s++) {
- if ((pvr & s->pvr_mask) == s->pvr_value) {
- setup_cpu_spec(offset, s);
- return s;
- }
+ if ((pvr & s->pvr_mask) == s->pvr_value)
+ return setup_cpu_spec(offset, s);
}
BUG();
EXPORT_SYMBOL(ioport_map);
EXPORT_SYMBOL(ioport_unmap);
+#ifdef CONFIG_PCI
void __iomem *pci_iomap(struct pci_dev *dev, int bar, unsigned long max)
{
resource_size_t start = pci_resource_start(dev, bar);
EXPORT_SYMBOL(pci_iomap);
EXPORT_SYMBOL(pci_iounmap);
+#endif /* CONFIG_PCI */
crashk_res.start = KDUMP_KERNELBASE;
#else
if (!crashk_res.start) {
+#ifdef CONFIG_PPC64
/*
- * unspecified address, choose a region of specified size
- * can overlap with initrd (ignoring corruption when retained)
- * ppc64 requires kernel and some stacks to be in first segemnt
+ * On 64bit we split the RMO in half but cap it at half of
+ * a small SLB (128MB) since the crash kernel needs to place
+ * itself and some stacks to be in the first segment.
*/
+ crashk_res.start = min(0x80000000ULL, (ppc64_rma_size / 2));
+#else
crashk_res.start = KDUMP_KERNELBASE;
+#endif
}
crash_base = PAGE_ALIGN(crashk_res.start);
((unsigned long)ptr & 7))
return -EFAULT;
- if (!__get_user_inatomic(*ret, ptr))
+ pagefault_disable();
+ if (!__get_user_inatomic(*ret, ptr)) {
+ pagefault_enable();
return 0;
+ }
+ pagefault_enable();
return read_user_stack_slow(ptr, ret, 8);
}
((unsigned long)ptr & 3))
return -EFAULT;
- if (!__get_user_inatomic(*ret, ptr))
+ pagefault_disable();
+ if (!__get_user_inatomic(*ret, ptr)) {
+ pagefault_enable();
return 0;
+ }
+ pagefault_enable();
return read_user_stack_slow(ptr, ret, 4);
}
*/
static int read_user_stack_32(unsigned int __user *ptr, unsigned int *ret)
{
+ int rc;
+
if ((unsigned long)ptr > TASK_SIZE - sizeof(unsigned int) ||
((unsigned long)ptr & 3))
return -EFAULT;
- return __get_user_inatomic(*ret, ptr);
+ pagefault_disable();
+ rc = __get_user_inatomic(*ret, ptr);
+ pagefault_enable();
+
+ return rc;
}
static inline void perf_callchain_user_64(struct perf_callchain_entry *entry,
}
if (addr == 0)
return 0;
- RELOC(alloc_bottom) = addr;
+ RELOC(alloc_bottom) = addr + size;
prom_debug(" -> %x\n", addr);
prom_debug(" alloc_bottom : %x\n", RELOC(alloc_bottom));
if (room > DEVTREE_CHUNK_SIZE)
room = DEVTREE_CHUNK_SIZE;
if (room < PAGE_SIZE)
- prom_panic("No memory for flatten_device_tree (no room)");
+ prom_panic("No memory for flatten_device_tree "
+ "(no room)\n");
chunk = alloc_up(room, 0);
if (chunk == 0)
- prom_panic("No memory for flatten_device_tree (claim failed)");
- *mem_end = RELOC(alloc_top);
+ prom_panic("No memory for flatten_device_tree "
+ "(claim failed)\n");
+ *mem_end = chunk + room;
}
ret = (void *)*mem_start;
/*
* Check how much room we have between alloc top & bottom (+/- a
- * few pages), crop to 4Mb, as this is our "chuck" size
+ * few pages), crop to 1MB, as this is our "chunk" size
*/
room = RELOC(alloc_top) - RELOC(alloc_bottom) - 0x4000;
if (room > DEVTREE_CHUNK_SIZE)
mem_start = (unsigned long)alloc_up(room, PAGE_SIZE);
if (mem_start == 0)
prom_panic("Can't allocate initial device-tree chunk\n");
- mem_end = RELOC(alloc_top);
+ mem_end = mem_start + room;
/* Get root of tree */
root = call_prom("peer", 1, 1, (phandle)0);
reg = 0
.rept 32
li r6,reg*16+VCPU_VSRS
- stxvd2x reg,r6,r3
+ STXVD2X(reg,r6,r3)
reg = reg + 1
.endr
FTR_SECTION_ELSE
reg = 0
.rept 32
li r7,reg*16+VCPU_VSRS
- lxvd2x reg,r7,r4
+ LXVD2X(reg,r7,r4)
reg = reg + 1
.endr
FTR_SECTION_ELSE
config KVM_GUEST
bool "KVM Guest support"
- default y
+ default n
---help---
This option enables various optimizations for running under the KVM
hypervisor. Overhead for the kernel when not running inside KVM should
lppaca_of(dtl->cpu).dtl_enable_mask = 0x0;
- unregister_dtl(hwcpu, __pa(dtl->buf));
+ unregister_dtl(hwcpu);
}
static u64 dtl_current_index(struct dtl *dtl)
get_lppaca()->idle = 0;
if (get_preferred_offline_state(cpu) == CPU_STATE_ONLINE) {
- unregister_slb_shadow(hwcpu, __pa(get_slb_shadow()));
+ unregister_slb_shadow(hwcpu);
/*
* Call to start_secondary_resume() will not return.
WARN_ON(get_preferred_offline_state(cpu) != CPU_STATE_OFFLINE);
set_cpu_current_state(cpu, CPU_STATE_OFFLINE);
- unregister_slb_shadow(hwcpu, __pa(get_slb_shadow()));
+ unregister_slb_shadow(hwcpu);
rtas_stop_self();
/* Should never get here... */
struct device_node *np;
ioei_check_exception_token = rtas_token("check-exception");
- if (ioei_check_exception_token == RTAS_UNKNOWN_SERVICE) {
- pr_warning("IO Event IRQ not supported on this system !\n");
+ if (ioei_check_exception_token == RTAS_UNKNOWN_SERVICE)
return -ENODEV;
- }
+
np = of_find_node_by_path("/event-sources/ibm,io-events");
if (np) {
request_event_sources_irqs(np, ioei_interrupt, "IO_EVENT");
+ pr_info("IBM I/O event interrupts enabled\n");
of_node_put(np);
} else {
- pr_err("io_event_irq: No ibm,io-events on system! "
- "IO Event interrupt disabled.\n");
return -ENODEV;
}
return 0;
{
/* Don't risk a hypervisor call if we're crashing */
if (firmware_has_feature(FW_FEATURE_SPLPAR) && !crash_shutdown) {
- unsigned long addr;
+ int ret;
+ int cpu = smp_processor_id();
+ int hwcpu = hard_smp_processor_id();
- addr = __pa(get_slb_shadow());
- if (unregister_slb_shadow(hard_smp_processor_id(), addr))
- printk("SLB shadow buffer deregistration of "
- "cpu %u (hw_cpu_id %d) failed\n",
- smp_processor_id(),
- hard_smp_processor_id());
+ if (get_lppaca()->dtl_enable_mask) {
+ ret = unregister_dtl(hwcpu);
+ if (ret) {
+ pr_err("WARNING: DTL deregistration for cpu "
+ "%d (hw %d) failed with %d\n",
+ cpu, hwcpu, ret);
+ }
+ }
+
+ ret = unregister_slb_shadow(hwcpu);
+ if (ret) {
+ pr_err("WARNING: SLB shadow buffer deregistration "
+ "for cpu %d (hw %d) failed with %d\n",
+ cpu, hwcpu, ret);
+ }
- addr = __pa(get_lppaca());
- if (unregister_vpa(hard_smp_processor_id(), addr)) {
- printk("VPA deregistration of cpu %u (hw_cpu_id %d) "
- "failed\n", smp_processor_id(),
- hard_smp_processor_id());
+ ret = unregister_vpa(hwcpu);
+ if (ret) {
+ pr_err("WARNING: VPA deregistration for cpu %d "
+ "(hw %d) failed with %d\n", cpu, hwcpu, ret);
}
}
}
ret = register_vpa(hwcpu, addr);
if (ret) {
- printk(KERN_ERR "WARNING: vpa_init: VPA registration for "
- "cpu %d (hw %d) of area %lx returns %ld\n",
- cpu, hwcpu, addr, ret);
+ pr_err("WARNING: VPA registration for cpu %d (hw %d) of area "
+ "%lx failed with %ld\n", cpu, hwcpu, addr, ret);
return;
}
/*
if (firmware_has_feature(FW_FEATURE_SPLPAR)) {
ret = register_slb_shadow(hwcpu, addr);
if (ret)
- printk(KERN_ERR
- "WARNING: vpa_init: SLB shadow buffer "
- "registration for cpu %d (hw %d) of area %lx "
- "returns %ld\n", cpu, hwcpu, addr, ret);
+ pr_err("WARNING: SLB shadow buffer registration for "
+ "cpu %d (hw %d) of area %lx failed with %ld\n",
+ cpu, hwcpu, addr, ret);
}
/*
dtl->enqueue_to_dispatch_time = DISPATCH_LOG_BYTES;
ret = register_dtl(hwcpu, __pa(dtl));
if (ret)
- pr_warn("DTL registration failed for cpu %d (%ld)\n",
- cpu, ret);
+ pr_err("WARNING: DTL registration of cpu %d (hw %d) "
+ "failed with %ld\n", smp_processor_id(),
+ hwcpu, ret);
lppaca_of(cpu).dtl_enable_mask = 2;
}
}
unsigned long ptel;
} ptes[4];
long lpar_rc;
- int i, j;
+ unsigned long i, j;
/* Read in batches of 4,
* invalidate only valid entries not in the VRMA
return plpar_hcall_norets(H_REGISTER_VPA, flags, cpu, vpa);
}
-static inline long unregister_vpa(unsigned long cpu, unsigned long vpa)
+static inline long unregister_vpa(unsigned long cpu)
{
- return vpa_call(0x5, cpu, vpa);
+ return vpa_call(0x5, cpu, 0);
}
static inline long register_vpa(unsigned long cpu, unsigned long vpa)
return vpa_call(0x1, cpu, vpa);
}
-static inline long unregister_slb_shadow(unsigned long cpu, unsigned long vpa)
+static inline long unregister_slb_shadow(unsigned long cpu)
{
- return vpa_call(0x7, cpu, vpa);
+ return vpa_call(0x7, cpu, 0);
}
static inline long register_slb_shadow(unsigned long cpu, unsigned long vpa)
return vpa_call(0x3, cpu, vpa);
}
-static inline long unregister_dtl(unsigned long cpu, unsigned long vpa)
+static inline long unregister_dtl(unsigned long cpu)
{
- return vpa_call(0x6, cpu, vpa);
+ return vpa_call(0x6, cpu, 0);
}
static inline long register_dtl(unsigned long cpu, unsigned long vpa)
dtl->enqueue_to_dispatch_time = DISPATCH_LOG_BYTES;
ret = register_dtl(hard_smp_processor_id(), __pa(dtl));
if (ret)
- pr_warn("DTL registration failed for boot cpu %d (%d)\n",
- smp_processor_id(), ret);
+ pr_err("WARNING: DTL registration of cpu %d (hw %d) failed "
+ "with %d\n", smp_processor_id(),
+ hard_smp_processor_id(), ret);
get_paca()->lppaca_ptr->dtl_enable_mask = 2;
return 0;
static struct ppc4xx_pciex_hwops *ppc4xx_pciex_hwops;
-#ifdef CONFIG_44x
-
static int __init ppc4xx_pciex_wait_on_sdr(struct ppc4xx_pciex_port *port,
unsigned int sdr_offset,
unsigned int mask,
return 0;
}
+
static void __init ppc4xx_pciex_check_link_sdr(struct ppc4xx_pciex_port *port)
{
printk(KERN_INFO "PCIE%d: Checking link...\n", port->index);
printk(KERN_INFO "PCIE%d: No device detected.\n", port->index);
}
+#ifdef CONFIG_44x
+
/* Check various reset bits of the 440SPe PCIe core */
static int __init ppc440spe_pciex_check_reset(struct device_node *np)
{
{
unsigned long hv_ret, major, minor;
- hv_ret = sun4v_get_version(HV_GRP_REBOOT_DATA, &major, &minor);
- if (hv_ret == HV_EOK) {
- pr_info("SUN4V: Reboot data supported (maj=%lu,min=%lu).\n",
- major, minor);
- reboot_data_supported = 1;
+ if (tlb_type == hypervisor) {
+ hv_ret = sun4v_get_version(HV_GRP_REBOOT_DATA, &major, &minor);
+ if (hv_ret == HV_EOK) {
+ pr_info("SUN4V: Reboot data supported (maj=%lu,min=%lu).\n",
+ major, minor);
+ reboot_data_supported = 1;
+ }
}
-
kthread_run(ds_thread, NULL, "kldomd");
return vio_register_driver(&ds_driver);
desc->base2 = (info->base_addr & 0xff000000) >> 24;
/*
- * Don't allow setting of the lm bit. It is useless anyway
- * because 64bit system calls require __USER_CS:
+ * Don't allow setting of the lm bit. It would confuse
+ * user_64bit_mode and would get overridden by sysret anyway.
*/
desc->l = 0;
}
* Vectors 0 ... 31 : system traps and exceptions - hardcoded events
* Vectors 32 ... 127 : device interrupts
* Vector 128 : legacy int80 syscall interface
- * Vector 204 : legacy x86_64 vsyscall emulation
* Vectors 129 ... INVALIDATE_TLB_VECTOR_START-1 except 204 : device interrupts
* Vectors INVALIDATE_TLB_VECTOR_START ... 255 : special interrupts
*
#ifdef CONFIG_X86_32
# define SYSCALL_VECTOR 0x80
#endif
-#ifdef CONFIG_X86_64
-# define VSYSCALL_EMU_VECTOR 0xcc
-#endif
/*
* Vectors 0x30-0x3f are used for ISA interrupts.
#include <asm/desc_defs.h>
#include <asm/kmap_types.h>
+#include <asm/pgtable_types.h>
struct page;
struct thread_struct;
struct pv_info {
unsigned int kernel_rpl;
int shared_kernel_pmd;
+
+#ifdef CONFIG_X86_64
+ u16 extra_user_64bit_cs; /* __USER_CS if none */
+#endif
+
int paravirt_enabled;
const char *name;
};
#ifdef __KERNEL__
#include <linux/init.h>
+#ifdef CONFIG_PARAVIRT
+#include <asm/paravirt_types.h>
+#endif
struct cpuinfo_x86;
struct task_struct;
#endif
}
+#ifdef CONFIG_X86_64
+static inline bool user_64bit_mode(struct pt_regs *regs)
+{
+#ifndef CONFIG_PARAVIRT
+ /*
+ * On non-paravirt systems, this is the only long mode CPL 3
+ * selector. We do not allow long mode selectors in the LDT.
+ */
+ return regs->cs == __USER_CS;
+#else
+ /* Headers are too twisted for this to go in paravirt.h. */
+ return regs->cs == __USER_CS || regs->cs == pv_info.extra_user_64bit_cs;
+#endif
+}
+#endif
+
/*
* X86_32 CPUs don't save ss and esp if the CPU is already in kernel mode
* when it traps. The previous stack will be directly underneath the saved
asmlinkage void machine_check(void);
#endif /* CONFIG_X86_MCE */
asmlinkage void simd_coprocessor_error(void);
-asmlinkage void emulate_vsyscall(void);
dotraplinkage void do_divide_error(struct pt_regs *, long);
dotraplinkage void do_debug(struct pt_regs *, long);
dotraplinkage void do_machine_check(struct pt_regs *, long);
#endif
dotraplinkage void do_simd_coprocessor_error(struct pt_regs *, long);
-dotraplinkage void do_emulate_vsyscall(struct pt_regs *, long);
#ifdef CONFIG_X86_32
dotraplinkage void do_iret_error(struct pt_regs *, long);
#endif
__SYSCALL(__NR_sendmmsg, sys_sendmmsg)
#define __NR_setns 308
__SYSCALL(__NR_setns, sys_setns)
+#define __NR_getcpu 309
+__SYSCALL(__NR_getcpu, sys_getcpu)
#ifndef __NO_STUBS
#define __ARCH_WANT_OLD_READDIR
extern void map_vsyscall(void);
+/*
+ * Called on instruction fetch fault in vsyscall page.
+ * Returns true if handled.
+ */
+extern bool emulate_vsyscall(struct pt_regs *regs, unsigned long address);
+
#endif /* __KERNEL__ */
#endif /* _ASM_X86_VSYSCALL_H */
CFLAGS_REMOVE_early_printk.o = -pg
endif
-#
-# vsyscalls (which work on the user stack) should have
-# no stack-protector checks:
-#
-nostackp := $(call cc-option, -fno-stack-protector)
-CFLAGS_vsyscall_64.o := $(PROFILING) -g0 $(nostackp)
-CFLAGS_hpet.o := $(nostackp)
-CFLAGS_paravirt.o := $(nostackp)
-GCOV_PROFILE_vsyscall_64.o := n
-GCOV_PROFILE_hpet.o := n
-GCOV_PROFILE_tsc.o := n
-GCOV_PROFILE_paravirt.o := n
-
obj-y := process_$(BITS).o signal.o entry_$(BITS).o
obj-y += traps.o irq.o irq_$(BITS).o dumpstack_$(BITS).o
obj-y += time.o ioport.o ldt.o dumpstack.o
break;
case 42: /* SandyBridge */
+ case 45: /* SandyBridge, "Romely-EP" */
memcpy(hw_cache_event_ids, snb_hw_cache_event_ids,
sizeof(hw_cache_event_ids));
zeroentry coprocessor_error do_coprocessor_error
errorentry alignment_check do_alignment_check
zeroentry simd_coprocessor_error do_simd_coprocessor_error
-zeroentry emulate_vsyscall do_emulate_vsyscall
/* Reload gs selector with exception handling */
.paravirt_enabled = 0,
.kernel_rpl = 0,
.shared_kernel_pmd = 1, /* Only used when CONFIG_X86_PAE is set */
+
+#ifdef CONFIG_X86_64
+ .extra_user_64bit_cs = __USER_CS,
+#endif
};
struct pv_init_ops pv_init_ops = {
#ifdef CONFIG_X86_64
case 0x40 ... 0x4f:
- if (regs->cs != __USER_CS)
+ if (!user_64bit_mode(regs))
/* 32-bit mode: register increment */
return 0;
/* 64-bit mode: REX prefix */
set_bit(SYSCALL_VECTOR, used_vectors);
#endif
-#ifdef CONFIG_X86_64
- BUG_ON(test_bit(VSYSCALL_EMU_VECTOR, used_vectors));
- set_system_intr_gate(VSYSCALL_EMU_VECTOR, &emulate_vsyscall);
- set_bit(VSYSCALL_EMU_VECTOR, used_vectors);
-#endif
-
/*
* Should be a barrier for any external CPU state:
*/
text PT_LOAD FLAGS(5); /* R_E */
data PT_LOAD FLAGS(6); /* RW_ */
#ifdef CONFIG_X86_64
- user PT_LOAD FLAGS(5); /* R_E */
#ifdef CONFIG_SMP
percpu PT_LOAD FLAGS(6); /* RW_ */
#endif
#ifdef CONFIG_X86_64
-#define VSYSCALL_ADDR (-10*1024*1024)
-
-#define VLOAD_OFFSET (VSYSCALL_ADDR - __vsyscall_0 + LOAD_OFFSET)
-#define VLOAD(x) (ADDR(x) - VLOAD_OFFSET)
-
-#define VVIRT_OFFSET (VSYSCALL_ADDR - __vsyscall_0)
-#define VVIRT(x) (ADDR(x) - VVIRT_OFFSET)
-
- . = ALIGN(4096);
- __vsyscall_0 = .;
-
- . = VSYSCALL_ADDR;
- .vsyscall : AT(VLOAD(.vsyscall)) {
- *(.vsyscall_0)
-
- . = 1024;
- *(.vsyscall_1)
-
- . = 2048;
- *(.vsyscall_2)
-
- . = 4096; /* Pad the whole page. */
- } :user =0xcc
- . = ALIGN(__vsyscall_0 + PAGE_SIZE, PAGE_SIZE);
-
-#undef VSYSCALL_ADDR
-#undef VLOAD_OFFSET
-#undef VLOAD
-#undef VVIRT_OFFSET
-#undef VVIRT
-
+ . = ALIGN(PAGE_SIZE);
__vvar_page = .;
.vvar : AT(ADDR(.vvar) - LOAD_OFFSET) {
+ /* work around gold bug 13023 */
+ __vvar_beginning_hack = .;
- /* Place all vvars at the offsets in asm/vvar.h. */
-#define EMIT_VVAR(name, offset) \
- . = offset; \
+ /* Place all vvars at the offsets in asm/vvar.h. */
+#define EMIT_VVAR(name, offset) \
+ . = __vvar_beginning_hack + offset; \
*(.vvar_ ## name)
#define __VVAR_KERNEL_LDS
#include <asm/vvar.h>
* use the vDSO.
*/
-/* Disable profiling for userspace code: */
-#define DISABLE_BRANCH_PROFILING
-
#include <linux/time.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <asm/vgtod.h>
#include <asm/traps.h>
+#define CREATE_TRACE_POINTS
+#include "vsyscall_trace.h"
+
DEFINE_VVAR(int, vgetcpu_mode);
DEFINE_VVAR(struct vsyscall_gtod_data, vsyscall_gtod_data) =
{
.lock = __SEQLOCK_UNLOCKED(__vsyscall_gtod_data.lock),
};
+static enum { EMULATE, NATIVE, NONE } vsyscall_mode = EMULATE;
+
+static int __init vsyscall_setup(char *str)
+{
+ if (str) {
+ if (!strcmp("emulate", str))
+ vsyscall_mode = EMULATE;
+ else if (!strcmp("native", str))
+ vsyscall_mode = NATIVE;
+ else if (!strcmp("none", str))
+ vsyscall_mode = NONE;
+ else
+ return -EINVAL;
+
+ return 0;
+ }
+
+ return -EINVAL;
+}
+early_param("vsyscall", vsyscall_setup);
+
void update_vsyscall_tz(void)
{
unsigned long flags;
printk("%s%s[%d] %s ip:%lx cs:%lx sp:%lx ax:%lx si:%lx di:%lx\n",
level, tsk->comm, task_pid_nr(tsk),
- message, regs->ip - 2, regs->cs,
+ message, regs->ip, regs->cs,
regs->sp, regs->ax, regs->si, regs->di);
}
return nr;
}
-void dotraplinkage do_emulate_vsyscall(struct pt_regs *regs, long error_code)
+bool emulate_vsyscall(struct pt_regs *regs, unsigned long address)
{
struct task_struct *tsk;
unsigned long caller;
int vsyscall_nr;
long ret;
- local_irq_enable();
-
/*
- * Real 64-bit user mode code has cs == __USER_CS. Anything else
- * is bogus.
+ * No point in checking CS -- the only way to get here is a user mode
+ * trap to a high address, which means that we're in 64-bit user code.
*/
- if (regs->cs != __USER_CS) {
- /*
- * If we trapped from kernel mode, we might as well OOPS now
- * instead of returning to some random address and OOPSing
- * then.
- */
- BUG_ON(!user_mode(regs));
- /* Compat mode and non-compat 32-bit CS should both segfault. */
- warn_bad_vsyscall(KERN_WARNING, regs,
- "illegal int 0xcc from 32-bit mode");
- goto sigsegv;
+ WARN_ON_ONCE(address != regs->ip);
+
+ if (vsyscall_mode == NONE) {
+ warn_bad_vsyscall(KERN_INFO, regs,
+ "vsyscall attempted with vsyscall=none");
+ return false;
}
- /*
- * x86-ism here: regs->ip points to the instruction after the int 0xcc,
- * and int 0xcc is two bytes long.
- */
- vsyscall_nr = addr_to_vsyscall_nr(regs->ip - 2);
+ vsyscall_nr = addr_to_vsyscall_nr(address);
+
+ trace_emulate_vsyscall(vsyscall_nr);
+
if (vsyscall_nr < 0) {
warn_bad_vsyscall(KERN_WARNING, regs,
- "illegal int 0xcc (exploit attempt?)");
+ "misaligned vsyscall (exploit attempt or buggy program) -- look up the vsyscall kernel parameter if you need a workaround");
goto sigsegv;
}
if (get_user(caller, (unsigned long __user *)regs->sp) != 0) {
- warn_bad_vsyscall(KERN_WARNING, regs, "int 0xcc with bad stack (exploit attempt?)");
+ warn_bad_vsyscall(KERN_WARNING, regs,
+ "vsyscall with bad stack (exploit attempt?)");
goto sigsegv;
}
regs->ip = caller;
regs->sp += 8;
- local_irq_disable();
- return;
+ return true;
sigsegv:
- regs->ip -= 2; /* The faulting instruction should be the int 0xcc. */
force_sig(SIGSEGV, current);
- local_irq_disable();
+ return true;
}
/*
void __init map_vsyscall(void)
{
- extern char __vsyscall_0;
- unsigned long physaddr_page0 = __pa_symbol(&__vsyscall_0);
+ extern char __vsyscall_page;
+ unsigned long physaddr_vsyscall = __pa_symbol(&__vsyscall_page);
extern char __vvar_page;
unsigned long physaddr_vvar_page = __pa_symbol(&__vvar_page);
- /* Note that VSYSCALL_MAPPED_PAGES must agree with the code below. */
- __set_fixmap(VSYSCALL_FIRST_PAGE, physaddr_page0, PAGE_KERNEL_VSYSCALL);
+ __set_fixmap(VSYSCALL_FIRST_PAGE, physaddr_vsyscall,
+ vsyscall_mode == NATIVE
+ ? PAGE_KERNEL_VSYSCALL
+ : PAGE_KERNEL_VVAR);
+ BUILD_BUG_ON((unsigned long)__fix_to_virt(VSYSCALL_FIRST_PAGE) !=
+ (unsigned long)VSYSCALL_START);
+
__set_fixmap(VVAR_PAGE, physaddr_vvar_page, PAGE_KERNEL_VVAR);
- BUILD_BUG_ON((unsigned long)__fix_to_virt(VVAR_PAGE) != (unsigned long)VVAR_ADDRESS);
+ BUILD_BUG_ON((unsigned long)__fix_to_virt(VVAR_PAGE) !=
+ (unsigned long)VVAR_ADDRESS);
}
static int __init vsyscall_init(void)
*/
#include <linux/linkage.h>
+
#include <asm/irq_vectors.h>
+#include <asm/page_types.h>
+#include <asm/unistd_64.h>
+
+__PAGE_ALIGNED_DATA
+ .globl __vsyscall_page
+ .balign PAGE_SIZE, 0xcc
+ .type __vsyscall_page, @object
+__vsyscall_page:
+
+ mov $__NR_gettimeofday, %rax
+ syscall
+ ret
-/* The unused parts of the page are filled with 0xcc by the linker script. */
+ .balign 1024, 0xcc
+ mov $__NR_time, %rax
+ syscall
+ ret
-.section .vsyscall_0, "a"
-ENTRY(vsyscall_0)
- int $VSYSCALL_EMU_VECTOR
-END(vsyscall_0)
+ .balign 1024, 0xcc
+ mov $__NR_getcpu, %rax
+ syscall
+ ret
-.section .vsyscall_1, "a"
-ENTRY(vsyscall_1)
- int $VSYSCALL_EMU_VECTOR
-END(vsyscall_1)
+ .balign 4096, 0xcc
-.section .vsyscall_2, "a"
-ENTRY(vsyscall_2)
- int $VSYSCALL_EMU_VECTOR
-END(vsyscall_2)
+ .size __vsyscall_page, 4096
--- /dev/null
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM vsyscall
+
+#if !defined(__VSYSCALL_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
+#define __VSYSCALL_TRACE_H
+
+#include <linux/tracepoint.h>
+
+TRACE_EVENT(emulate_vsyscall,
+
+ TP_PROTO(int nr),
+
+ TP_ARGS(nr),
+
+ TP_STRUCT__entry(__field(int, nr)),
+
+ TP_fast_assign(
+ __entry->nr = nr;
+ ),
+
+ TP_printk("nr = %d", __entry->nr)
+);
+
+#endif
+
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH ../../arch/x86/kernel
+#define TRACE_INCLUDE_FILE vsyscall_trace
+#include <trace/define_trace.h>
* but for now it's good enough to assume that long
* mode only uses well known segments or kernel.
*/
- return (!user_mode(regs)) || (regs->cs == __USER_CS);
+ return (!user_mode(regs) || user_64bit_mode(regs));
#endif
case 0x60:
/* 0x64 thru 0x67 are valid prefixes in all modes. */
if (is_errata100(regs, address))
return;
+#ifdef CONFIG_X86_64
+ /*
+ * Instruction fetch faults in the vsyscall page might need
+ * emulation.
+ */
+ if (unlikely((error_code & PF_INSTR) &&
+ ((address & ~0xfff) == VSYSCALL_START))) {
+ if (emulate_vsyscall(regs, address))
+ return;
+ }
+#endif
+
if (unlikely(show_unhandled_signals))
show_signal_msg(regs, error_code, address, tsk);
vdso_start:
.incbin "arch/x86/vdso/vdso.so"
vdso_end:
+ .align PAGE_SIZE /* extra data here leaks to userspace. */
.previous
.paravirt_enabled = 1,
.shared_kernel_pmd = 0,
+#ifdef CONFIG_X86_64
+ .extra_user_64bit_cs = FLAT_USER_CS64,
+#endif
+
.name = "Xen",
};
# endif
#else
case VSYSCALL_LAST_PAGE ... VSYSCALL_FIRST_PAGE:
+ case VVAR_PAGE:
#endif
case FIX_TEXT_POKE0:
case FIX_TEXT_POKE1:
#ifdef CONFIG_X86_64
/* Replicate changes to map the vsyscall page into the user
pagetable vsyscall mapping. */
- if (idx >= VSYSCALL_LAST_PAGE && idx <= VSYSCALL_FIRST_PAGE) {
+ if ((idx >= VSYSCALL_LAST_PAGE && idx <= VSYSCALL_FIRST_PAGE) ||
+ idx == VVAR_PAGE) {
unsigned long vaddr = __fix_to_virt(idx);
set_pte_vaddr_pud(level3_user_vsyscall, vaddr, pte);
}
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/delay.h>
+#include <linux/dma-mapping.h>
#include <linux/dmapool.h>
#include <linux/dmaengine.h>
#include <linux/amba/bus.h>
fp->disable_tpa = ((bp->flags & TPA_ENABLE_FLAG) == 0);
#ifdef BCM_CNIC
- /* We don't want TPA on FCoE, FWD and OOO L2 rings */
- bnx2x_fcoe(bp, disable_tpa) = 1;
+ /* We don't want TPA on an FCoE L2 ring */
+ if (IS_FCOE_FP(fp))
+ fp->disable_tpa = 1;
#endif
}
u16 bnx2x_select_queue(struct net_device *dev, struct sk_buff *skb)
{
struct bnx2x *bp = netdev_priv(dev);
+
#ifdef BCM_CNIC
- if (NO_FCOE(bp))
- return skb_tx_hash(dev, skb);
- else {
+ if (!NO_FCOE(bp)) {
struct ethhdr *hdr = (struct ethhdr *)skb->data;
u16 ether_type = ntohs(hdr->h_proto);
return bnx2x_fcoe_tx(bp, txq_index);
}
#endif
- /* Select a none-FCoE queue: if FCoE is enabled, exclude FCoE L2 ring
- */
+ /* select a non-FCoE queue */
return __skb_tx_hash(dev, skb, BNX2X_NUM_ETH_QUEUES(bp));
}
bp->num_queues += NON_ETH_CONTEXT_USE;
}
+/**
+ * bnx2x_set_real_num_queues - configure netdev->real_num_[tx,rx]_queues
+ *
+ * @bp: Driver handle
+ *
+ * We currently support for at most 16 Tx queues for each CoS thus we will
+ * allocate a multiple of 16 for ETH L2 rings according to the value of the
+ * bp->max_cos.
+ *
+ * If there is an FCoE L2 queue the appropriate Tx queue will have the next
+ * index after all ETH L2 indices.
+ *
+ * If the actual number of Tx queues (for each CoS) is less than 16 then there
+ * will be the holes at the end of each group of 16 ETh L2 indices (0..15,
+ * 16..31,...) with indicies that are not coupled with any real Tx queue.
+ *
+ * The proper configuration of skb->queue_mapping is handled by
+ * bnx2x_select_queue() and __skb_tx_hash().
+ *
+ * bnx2x_setup_tc() takes care of the proper TC mappings so that __skb_tx_hash()
+ * will return a proper Tx index if TC is enabled (netdev->num_tc > 0).
+ */
static inline int bnx2x_set_real_num_queues(struct bnx2x *bp)
{
int rc, tx, rx;
void bnx2x_dcbx_set_state(struct bnx2x *bp, bool dcb_on, u32 dcbx_enabled)
{
- if (!CHIP_IS_E1x(bp)) {
+ if (!CHIP_IS_E1x(bp) && !CHIP_IS_E3(bp)) {
bp->dcb_state = dcb_on;
bp->dcbx_enabled = dcbx_enabled;
} else {
DP(BNX2X_MSG_MCP, "starting common init func %d\n", BP_ABS_FUNC(bp));
+ /*
+ * take the UNDI lock to protect undi_unload flow from accessing
+ * registers while we're resetting the chip
+ */
+ bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
+
bnx2x_reset_common(bp);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0xffffffff);
}
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, val);
+ bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_UNDI);
+
bnx2x_init_block(bp, BLOCK_MISC, PHASE_COMMON);
if (!CHIP_IS_E1x(bp)) {
/* clean indirect addresses */
pci_write_config_dword(bp->pdev, PCICFG_GRC_ADDRESS,
PCICFG_VENDOR_ID_OFFSET);
- REG_WR(bp, PXP2_REG_PGL_ADDR_88_F0 + BP_PORT(bp)*16, 0);
- REG_WR(bp, PXP2_REG_PGL_ADDR_8C_F0 + BP_PORT(bp)*16, 0);
- REG_WR(bp, PXP2_REG_PGL_ADDR_90_F0 + BP_PORT(bp)*16, 0);
- REG_WR(bp, PXP2_REG_PGL_ADDR_94_F0 + BP_PORT(bp)*16, 0);
+ /* Clean the following indirect addresses for all functions since it
+ * is not used by the driver.
+ */
+ REG_WR(bp, PXP2_REG_PGL_ADDR_88_F0, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_8C_F0, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_90_F0, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_94_F0, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_88_F1, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_8C_F1, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_90_F1, 0);
+ REG_WR(bp, PXP2_REG_PGL_ADDR_94_F1, 0);
/*
* Enable internal target-read (in case we are probed after PF FLR).
/* [R 6] Debug only: Number of used entries in the data FIFO */
#define PXP2_REG_HST_DATA_FIFO_STATUS 0x12047c
/* [R 7] Debug only: Number of used entries in the header FIFO */
-#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
-#define PXP2_REG_PGL_ADDR_88_F0 0x120534
-#define PXP2_REG_PGL_ADDR_8C_F0 0x120538
-#define PXP2_REG_PGL_ADDR_90_F0 0x12053c
-#define PXP2_REG_PGL_ADDR_94_F0 0x120540
+#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
+#define PXP2_REG_PGL_ADDR_88_F0 0x120534
+/* [R 32] GRC address for configuration access to PCIE config address 0x88.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_88_F1 0x120544
+#define PXP2_REG_PGL_ADDR_8C_F0 0x120538
+/* [R 32] GRC address for configuration access to PCIE config address 0x8c.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_8C_F1 0x120548
+#define PXP2_REG_PGL_ADDR_90_F0 0x12053c
+/* [R 32] GRC address for configuration access to PCIE config address 0x90.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_90_F1 0x12054c
+#define PXP2_REG_PGL_ADDR_94_F0 0x120540
+/* [R 32] GRC address for configuration access to PCIE config address 0x94.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_94_F1 0x120550
#define PXP2_REG_PGL_CONTROL0 0x120490
#define PXP2_REG_PGL_CONTROL1 0x120514
#define PXP2_REG_PGL_DEBUG 0x120520
skb->ip_summed = CHECKSUM_UNNECESSARY;
memcpy(skb_put(skb, sizeof(struct can_frame)),
&cf, sizeof(struct can_frame));
- netif_rx(skb);
+ netif_rx_ni(skb);
sl->dev->stats.rx_packets++;
sl->dev->stats.rx_bytes += cf.can_dlc;
| FLAG_HAS_AMT
| FLAG_HAS_CTRLEXT_ON_LOAD,
.flags2 = FLAG2_CHECK_PHY_HANG
- | FLAG2_DISABLE_ASPM_L0S,
+ | FLAG2_DISABLE_ASPM_L0S
+ | FLAG2_NO_DISABLE_RX,
.pba = 32,
.max_hw_frame_size = DEFAULT_JUMBO,
.get_variants = e1000_get_variants_82571,
| FLAG_HAS_AMT
| FLAG_HAS_JUMBO_FRAMES
| FLAG_HAS_CTRLEXT_ON_LOAD,
- .flags2 = FLAG2_DISABLE_ASPM_L0S,
+ .flags2 = FLAG2_DISABLE_ASPM_L0S
+ | FLAG2_NO_DISABLE_RX,
.pba = 32,
.max_hw_frame_size = DEFAULT_JUMBO,
.get_variants = e1000_get_variants_82571,
#define FLAG2_DISABLE_ASPM_L0S (1 << 7)
#define FLAG2_DISABLE_AIM (1 << 8)
#define FLAG2_CHECK_PHY_HANG (1 << 9)
+#define FLAG2_NO_DISABLE_RX (1 << 10)
#define E1000_RX_DESC_PS(R, i) \
(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
rx_ring->next_to_clean = 0;
rctl = er32(RCTL);
- ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
ew32(RDBAL, ((u64) rx_ring->dma & 0xFFFFFFFF));
ew32(RDBAH, ((u64) rx_ring->dma >> 32));
ew32(RDLEN, rx_ring->size);
/* Check for LOM (vs. NIC) or one of two valid mezzanine cards */
if (!((nvm_data & NVM_COMPAT_LOM) ||
(hw->adapter->pdev->device == E1000_DEV_ID_82571EB_SERDES_DUAL) ||
- (hw->adapter->pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)))
+ (hw->adapter->pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD) ||
+ (hw->adapter->pdev->device == E1000_DEV_ID_82571EB_SERDES)))
goto out;
ret_val = e1000_read_nvm(hw, NVM_ALT_MAC_ADDR_PTR, 1,
goto out;
}
- if (nvm_alt_mac_addr_offset == 0xFFFF) {
+ if ((nvm_alt_mac_addr_offset == 0xFFFF) ||
+ (nvm_alt_mac_addr_offset == 0x0000))
/* There is no Alternate MAC Address */
goto out;
- }
if (hw->bus.func == E1000_FUNC_1)
nvm_alt_mac_addr_offset += E1000_ALT_MAC_ADDRESS_OFFSET_LAN1;
#define DRV_EXTRAVERSION "-k"
-#define DRV_VERSION "1.3.16" DRV_EXTRAVERSION
+#define DRV_VERSION "1.4.4" DRV_EXTRAVERSION
char e1000e_driver_name[] = "e1000e";
const char e1000e_driver_version[] = DRV_VERSION;
/* disable receives while setting up the descriptors */
rctl = er32(RCTL);
- ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
e1e_flush();
usleep_range(10000, 20000);
/* disable receives in the hardware */
rctl = er32(RCTL);
- ew32(RCTL, rctl & ~E1000_RCTL_EN);
+ if (!(adapter->flags2 & FLAG2_NO_DISABLE_RX))
+ ew32(RCTL, rctl & ~E1000_RCTL_EN);
/* flush and sleep below */
netif_stop_queue(netdev);
tctl = er32(TCTL);
tctl &= ~E1000_TCTL_EN;
ew32(TCTL, tctl);
+
/* flush both disables and wait for them to finish */
e1e_flush();
usleep_range(10000, 20000);
/* Caller must hold etsects->lock. */
static void set_fipers(struct etsects *etsects)
{
- u32 tmr_ctrl = gfar_read(&etsects->regs->tmr_ctrl);
-
- gfar_write(&etsects->regs->tmr_ctrl, tmr_ctrl & (~TE));
- gfar_write(&etsects->regs->tmr_prsc, etsects->tmr_prsc);
+ set_alarm(etsects);
gfar_write(&etsects->regs->tmr_fiper1, etsects->tmr_fiper1);
gfar_write(&etsects->regs->tmr_fiper2, etsects->tmr_fiper2);
- set_alarm(etsects);
- gfar_write(&etsects->regs->tmr_ctrl, tmr_ctrl|TE);
}
/*
gfar_write(&etsects->regs->tmr_fiper1, etsects->tmr_fiper1);
gfar_write(&etsects->regs->tmr_fiper2, etsects->tmr_fiper2);
set_alarm(etsects);
- gfar_write(&etsects->regs->tmr_ctrl, tmr_ctrl|FS|RTPE|TE);
+ gfar_write(&etsects->regs->tmr_ctrl, tmr_ctrl|FS|RTPE|TE|FRD);
spin_unlock_irqrestore(&etsects->lock, flags);
* - DMA transfer support
* - FIFO mode support
*/
+#include <linux/io.h>
+#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
* published by the Free Software Foundation.
*/
+#include <linux/io.h>
+#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
static int sh_sir_read_data(struct sh_sir_self *self)
{
- u16 val;
+ u16 val = 0;
int timeout = 1024;
while (timeout--) {
/*
* VLB I/O addresses
*/
-static unsigned int pcnet32_portlist[] __initdata =
+static unsigned int pcnet32_portlist[] =
{ 0x300, 0x320, 0x340, 0x360, 0 };
static int pcnet32_debug;
#define PAGESEL 0x13
#define LAYER4 0x02
#define LAYER2 0x01
-#define MAX_RXTS 4
-#define MAX_TXTS 4
+#define MAX_RXTS 64
#define N_EXT_TS 1
#define PSF_PTPVER 2
#define PSF_EVNT 0x4000
rxts->seqid = p->seqid;
rxts->msgtype = (p->msgtype >> 12) & 0xf;
rxts->hash = p->msgtype & 0x0fff;
- rxts->tmo = jiffies + HZ;
+ rxts->tmo = jiffies + 2;
}
static u64 phy2txts(struct phy_txts *p)
memcpy(skb_put(skb, count), sl->rbuff, count);
skb_reset_mac_header(skb);
skb->protocol = htons(ETH_P_IP);
- netif_rx(skb);
+ netif_rx_ni(skb);
dev->stats.rx_packets++;
}
usb_set_intfdata(intf, NULL);
if (dev) {
set_bit(RTL8150_UNPLUG, &dev->flags);
- tasklet_disable(&dev->tl);
tasklet_kill(&dev->tl);
unregister_netdev(dev->netdev);
unlink_all_urbs(dev);
if (dma_mapping_error(ah->dev, bf->skbaddr)) {
ATH5K_ERR(ah, "beacon DMA mapping failed\n");
+ dev_kfree_skb_any(skb);
+ bf->skb = NULL;
return -EIO;
}
ath5k_txbuf_free_skb(ah, avf->bbuf);
avf->bbuf->skb = skb;
ret = ath5k_beacon_setup(ah, avf->bbuf);
- if (ret)
- avf->bbuf->skb = NULL;
out:
return ret;
}
struct ath5k_vif *avf;
struct ath5k_buf *bf;
struct sk_buff *skb;
+ int err;
ATH5K_DBG_UNLIMIT(ah, ATH5K_DEBUG_BEACON, "in beacon_send\n");
avf = (void *)vif->drv_priv;
bf = avf->bbuf;
- if (unlikely(bf->skb == NULL || ah->opmode == NL80211_IFTYPE_STATION ||
- ah->opmode == NL80211_IFTYPE_MONITOR)) {
- ATH5K_WARN(ah, "bf=%p bf_skb=%p\n", bf, bf ? bf->skb : NULL);
- return;
- }
/*
* Stop any current dma and put the new frame on the queue.
/* refresh the beacon for AP or MESH mode */
if (ah->opmode == NL80211_IFTYPE_AP ||
- ah->opmode == NL80211_IFTYPE_MESH_POINT)
- ath5k_beacon_update(ah->hw, vif);
+ ah->opmode == NL80211_IFTYPE_MESH_POINT) {
+ err = ath5k_beacon_update(ah->hw, vif);
+ if (err)
+ return;
+ }
+
+ if (unlikely(bf->skb == NULL || ah->opmode == NL80211_IFTYPE_STATION ||
+ ah->opmode == NL80211_IFTYPE_MONITOR)) {
+ ATH5K_WARN(ah, "bf=%p bf_skb=%p\n", bf, bf->skb);
+ return;
+ }
trace_ath5k_tx(ah, bf->skb, &ah->txqs[ah->bhalq]);
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 1) } },
- { { CTL(60, 1), CTL(60, 0), CTL(0, 0), CTL(0, 0) } },
+ { { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 1) } },
- { { CTL(60, 1), CTL(60, 0), CTL(0, 0), CTL(0, 0) } },
+ { { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 1) } },
- { { CTL(60, 1), CTL(60, 0), CTL(0, 0), CTL(0, 0) } },
+ { { CTL(60, 1), CTL(60, 0), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
{ { CTL(60, 0), CTL(60, 1), CTL(60, 0), CTL(60, 0) } },
}
} else {
reg_pmu_set = (5 << 1) | (7 << 4) |
- (1 << 8) | (2 << 14) |
+ (2 << 8) | (2 << 14) |
(6 << 17) | (1 << 20) |
(3 << 24) | (1 << 28);
}
#define AR_PHY_TPC_11_B1 (AR_SM1_BASE + 0x220)
#define AR_PHY_PDADC_TAB_1 (AR_SM1_BASE + 0x240)
#define AR_PHY_TX_IQCAL_STATUS_B1 (AR_SM1_BASE + 0x48c)
-#define AR_PHY_TX_IQCAL_CORR_COEFF_B1(_i) (AR_SM_BASE + 0x450 + ((_i) << 2))
+#define AR_PHY_TX_IQCAL_CORR_COEFF_B1(_i) (AR_SM1_BASE + 0x450 + ((_i) << 2))
/*
* Channel 2 Register Map
u32 tmp;
u16 mmio_base;
- tmp = b43_read32(dev, SSB_TMSHIGH);
- if (tmp & SSB_TMSHIGH_DMA64)
- return DMA_BIT_MASK(64);
+ switch (dev->dev->bus_type) {
+#ifdef CONFIG_B43_BCMA
+ case B43_BUS_BCMA:
+ tmp = bcma_aread32(dev->dev->bdev, BCMA_IOST);
+ if (tmp & BCMA_IOST_DMA64)
+ return DMA_BIT_MASK(64);
+ break;
+#endif
+#ifdef CONFIG_B43_SSB
+ case B43_BUS_SSB:
+ tmp = ssb_read32(dev->dev->sdev, SSB_TMSHIGH);
+ if (tmp & SSB_TMSHIGH_DMA64)
+ return DMA_BIT_MASK(64);
+ break;
+#endif
+ }
+
mmio_base = b43_dmacontroller_base(0, 0);
b43_write32(dev, mmio_base + B43_DMA32_TXCTL, B43_DMA32_TXADDREXT_MASK);
tmp = b43_read32(dev, mmio_base + B43_DMA32_TXCTL);
{ USB_DEVICE(0x07d1, 0x3c16) },
/* Draytek */
{ USB_DEVICE(0x07fa, 0x7712) },
+ /* DVICO */
+ { USB_DEVICE(0x0fe9, 0xb307) },
/* Edimax */
{ USB_DEVICE(0x7392, 0x7711) },
{ USB_DEVICE(0x7392, 0x7717) },
/* Buffalo */
{ USB_DEVICE(0x0411, 0x00d8) },
{ USB_DEVICE(0x0411, 0x00d9) },
+ { USB_DEVICE(0x0411, 0x00e6) },
{ USB_DEVICE(0x0411, 0x00f4) },
{ USB_DEVICE(0x0411, 0x0116) },
{ USB_DEVICE(0x0411, 0x0119) },
{RTL_USB_DEVICE(USB_VENDER_ID_REALTEK, 0x817d, rtl92cu_hal_cfg)},
/* 8188CE-VAU USB minCard (b/g mode only) */
{RTL_USB_DEVICE(USB_VENDER_ID_REALTEK, 0x817e, rtl92cu_hal_cfg)},
+ /* 8188RU in Alfa AWUS036NHR */
+ {RTL_USB_DEVICE(USB_VENDER_ID_REALTEK, 0x817f, rtl92cu_hal_cfg)},
/* 8188 Combo for BC4 */
{RTL_USB_DEVICE(USB_VENDER_ID_REALTEK, 0x8754, rtl92cu_hal_cfg)},
{RTL_USB_DEVICE(0x0eb0, 0x9071, rtl92cu_hal_cfg)}, /*NO Brand - Etop*/
/* HP - Lite-On ,8188CUS Slim Combo */
{RTL_USB_DEVICE(0x103c, 0x1629, rtl92cu_hal_cfg)},
+ {RTL_USB_DEVICE(0x13d3, 0x3357, rtl92cu_hal_cfg)}, /* AzureWave */
{RTL_USB_DEVICE(0x2001, 0x3308, rtl92cu_hal_cfg)}, /*D-Link - Alpha*/
{RTL_USB_DEVICE(0x2019, 0xab2a, rtl92cu_hal_cfg)}, /*Planex - Abocom*/
{RTL_USB_DEVICE(0x2019, 0xed17, rtl92cu_hal_cfg)}, /*PCI - Edimax*/
{RTL_USB_DEVICE(0x20f4, 0x648b, rtl92cu_hal_cfg)}, /*TRENDnet - Cameo*/
{RTL_USB_DEVICE(0x7392, 0x7811, rtl92cu_hal_cfg)}, /*Edimax - Edimax*/
- {RTL_USB_DEVICE(0x3358, 0x13d3, rtl92cu_hal_cfg)}, /*Azwave 8188CE-VAU*/
+ {RTL_USB_DEVICE(0x13d3, 0x3358, rtl92cu_hal_cfg)}, /*Azwave 8188CE-VAU*/
/* Russian customer -Azwave (8188CE-VAU b/g mode only) */
- {RTL_USB_DEVICE(0x3359, 0x13d3, rtl92cu_hal_cfg)},
+ {RTL_USB_DEVICE(0x13d3, 0x3359, rtl92cu_hal_cfg)},
+ {RTL_USB_DEVICE(0x4855, 0x0090, rtl92cu_hal_cfg)}, /* Feixun */
+ {RTL_USB_DEVICE(0x4855, 0x0091, rtl92cu_hal_cfg)}, /* NetweeN-Feixun */
+ {RTL_USB_DEVICE(0x9846, 0x9041, rtl92cu_hal_cfg)}, /* Netgear Cameo */
/****** 8192CU ********/
{RTL_USB_DEVICE(0x0586, 0x341f, rtl92cu_hal_cfg)}, /*Zyxel -Abocom*/
{RTL_USB_DEVICE(0x07aa, 0x0056, rtl92cu_hal_cfg)}, /*ATKK-Gemtek*/
{RTL_USB_DEVICE(0x07b8, 0x8178, rtl92cu_hal_cfg)}, /*Funai -Abocom*/
- {RTL_USB_DEVICE(0x07b8, 0x8178, rtl92cu_hal_cfg)}, /*Abocom -Abocom*/
{RTL_USB_DEVICE(0x2001, 0x3307, rtl92cu_hal_cfg)}, /*D-Link-Cameo*/
{RTL_USB_DEVICE(0x2001, 0x3309, rtl92cu_hal_cfg)}, /*D-Link-Alpha*/
{RTL_USB_DEVICE(0x2001, 0x330a, rtl92cu_hal_cfg)}, /*D-Link-Alpha*/
auth->sleep_auth = sleep_auth;
ret = wl1251_cmd_configure(wl, ACX_SLEEP_AUTH, auth, sizeof(*auth));
- if (ret < 0)
- return ret;
out:
kfree(auth);
ret = wl1251_cmd_configure(wl, ACX_CCA_THRESHOLD,
detection, sizeof(*detection));
- if (ret < 0) {
+ if (ret < 0)
wl1251_warning("failed to set cca threshold: %d", ret);
- return ret;
- }
out:
kfree(detection);
if (ret < 0) {
wl1251_error("tx %s cmd for channel %d failed",
enable ? "start" : "stop", channel);
- return ret;
+ goto out;
}
wl1251_debug(DEBUG_BOOT, "tx %s cmd channel %d",
for(count = 0; count < Patch_Count; count++) {
AR_DEBUG_PRINTF(ATH_DEBUG_ERR,("Freeing Patch Buffer %d \r\n",count));
- kfree(RamPatch[Patch_Count].Data);
+ kfree(RamPatch[count].Data);
}
for(count = 0; count < Tag_Count; count++) {
#include <linux/stringify.h>
#include <linux/delay.h>
#include <linux/kthread.h>
+#include <linux/slab.h>
#include <media/v4l2-dev.h>
#include <media/v4l2-ioctl.h>
#include <media/videobuf2-dma-contig.h>
#include <linux/string.h>
#include <linux/vmalloc.h>
#include <linux/netdevice.h>
+#include <asm/io.h>
#include <asm/uaccess.h>
#include "ft1000.h"
#include <drm/drmP.h>
#include <drm/drm.h>
-/**
- * Initialize an already allocated GEM object of the specified size with
- * no GEM provided backing store. Instead the caller is responsible for
- * backing the object and handling it.
- */
-int drm_gem_private_object_init(struct drm_device *dev,
- struct drm_gem_object *obj, size_t size)
-{
- BUG_ON((size & (PAGE_SIZE - 1)) != 0);
-
- obj->dev = dev;
- obj->filp = NULL;
-
- kref_init(&obj->refcount);
- atomic_set(&obj->handle_count, 0);
- obj->size = size;
-
- return 0;
-}
-
void drm_gem_object_release_wrap(struct drm_gem_object *obj)
{
/* Remove the list map if one is present */
kfree(list->map);
list->map = NULL;
}
- if (obj->filp)
- drm_gem_object_release(obj);
+ drm_gem_object_release(obj);
}
/**
extern void drm_gem_object_release_wrap(struct drm_gem_object *obj);
-extern int drm_gem_private_object_init(struct drm_device *dev,
- struct drm_gem_object *obj, size_t size);
extern int gem_create_mmap_offset(struct drm_gem_object *obj);
page_buf = alloc_page(GFP_KERNEL);
if (!page_buf) {
- kmem_cache_free(blkvsc_req->dev->request_pool, blkvsc_req);
+ kmem_cache_free(blkdev->request_pool, blkvsc_req);
return -ENOMEM;
}
__free_page(page_buf);
- kmem_cache_free(blkvsc_req->dev->request_pool, blkvsc_req);
+ kmem_cache_free(blkdev->request_pool, blkvsc_req);
return ret;
}
mutex_lock(&indio_dev->mlock);
addr = adis16203_addresses[chan->address][0];
ret = adis16203_spi_read_reg_16(indio_dev, addr, &val16);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
if (val16 & ADIS16203_ERROR_ACTIVE) {
ret = adis16203_check_status(indio_dev);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
}
val16 = val16 & ((1 << chan->scan_type.realbits) - 1);
if (chan->scan_type.sign == 's')
mutex_lock(&indio_dev->mlock);
addr = adis16204_addresses[chan->address][0];
ret = adis16204_spi_read_reg_16(indio_dev, addr, &val16);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
if (val16 & ADIS16204_ERROR_ACTIVE) {
ret = adis16204_check_status(indio_dev);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
}
val16 = val16 & ((1 << chan->scan_type.realbits) - 1);
if (chan->scan_type.sign == 's')
mutex_lock(&indio_dev->mlock);
addr = adis16209_addresses[chan->address][0];
ret = adis16209_spi_read_reg_16(indio_dev, addr, &val16);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
if (val16 & ADIS16209_ERROR_ACTIVE) {
ret = adis16209_check_status(indio_dev);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
}
val16 = val16 & ((1 << chan->scan_type.realbits) - 1);
if (chan->scan_type.sign == 's')
mutex_lock(&indio_dev->mlock);
addr = adis16240_addresses[chan->address][0];
ret = adis16240_spi_read_reg_16(indio_dev, addr, &val16);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
if (val16 & ADIS16240_ERROR_ACTIVE) {
ret = adis16240_check_status(indio_dev);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
}
val16 = val16 & ((1 << chan->scan_type.realbits) - 1);
if (chan->scan_type.sign == 's')
mutex_lock(&indio_dev->mlock);
addr = adis16260_addresses[chan->address][0];
ret = adis16260_spi_read_reg_16(indio_dev, addr, &val16);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
if (val16 & ADIS16260_ERROR_ACTIVE) {
ret = adis16260_check_status(indio_dev);
- if (ret)
+ if (ret) {
+ mutex_unlock(&indio_dev->mlock);
return ret;
+ }
}
val16 = val16 & ((1 << chan->scan_type.realbits) - 1);
if (chan->scan_type.sign == 's')
- add compile as module support
- move nvec devices to mfd cells?
- adjust to kernel style
-
-
+ - fix clk usage
+ should not be using clk_get_sys(), but clk_get(&pdev->dev, conn)
+ where conn is either NULL if the device only has one clock, or
+ the device specific name if it has multiple clocks.
}
-
-
-
-
-
-
+MODULE_FIRMWARE("RTL8192U/boot.img");
+MODULE_FIRMWARE("RTL8192U/main.img");
+MODULE_FIRMWARE("RTL8192U/data.img");
module_param(msi_en, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(msi_en, "enable msi");
-/* These are used to make sure the module doesn't unload before all the
- * threads have exited.
- */
-static atomic_t total_threads = ATOMIC_INIT(0);
-static DECLARE_COMPLETION(threads_gone);
-
static irqreturn_t rtsx_interrupt(int irq, void *dev_id);
/***********************************************************************
/* enqueue the command and wake up the control thread */
srb->scsi_done = done;
chip->srb = srb;
- up(&(dev->sema));
+ complete(&dev->cmnd_ready);
return 0;
}
current->flags |= PF_NOFREEZE;
for (;;) {
- if (down_interruptible(&dev->sema))
+ if (wait_for_completion_interruptible(&dev->cmnd_ready))
break;
/* lock the device pointers */
mutex_unlock(&dev->dev_mutex);
} /* for (;;) */
- scsi_host_put(host);
-
/* notify the exit routine that we're actually exiting now
*
* complete()/wait_for_completion() is similar to up()/down(),
* This is important in preemption kernels, which transfer the flow
* of execution immediately upon a complete().
*/
- complete_and_exit(&threads_gone, 0);
+ complete_and_exit(&dev->control_exit, 0);
}
{
struct rtsx_dev *dev = (struct rtsx_dev *)__dev;
struct rtsx_chip *chip = dev->chip;
- struct Scsi_Host *host = rtsx_to_host(dev);
struct sd_info *sd_card = &(chip->sd_card);
struct xd_info *xd_card = &(chip->xd_card);
struct ms_info *ms_card = &(chip->ms_card);
mutex_unlock(&dev->dev_mutex);
}
- scsi_host_put(host);
- complete_and_exit(&threads_gone, 0);
+ complete_and_exit(&dev->polling_exit, 0);
}
/*
{
printk(KERN_INFO "-- %s\n", __func__);
+ /* Tell the control thread to exit. The SCSI host must
+ * already have been removed so it won't try to queue
+ * any more commands.
+ */
+ printk(KERN_INFO "-- sending exit command to thread\n");
+ complete(&dev->cmnd_ready);
+ if (dev->ctl_thread)
+ wait_for_completion(&dev->control_exit);
+ if (dev->polling_thread)
+ wait_for_completion(&dev->polling_exit);
+
+ wait_timeout(200);
+
if (dev->rtsx_resv_buf) {
- dma_free_coherent(&(dev->pci->dev), HOST_CMDS_BUF_LEN,
+ dma_free_coherent(&(dev->pci->dev), RTSX_RESV_BUF_LEN,
dev->rtsx_resv_buf, dev->rtsx_resv_buf_addr);
dev->chip->host_cmds_ptr = NULL;
dev->chip->host_sg_tbl_ptr = NULL;
}
- pci_disable_device(dev->pci);
- pci_release_regions(dev->pci);
-
- if (dev->irq > 0) {
+ if (dev->irq > 0)
free_irq(dev->irq, (void *)dev);
- }
- if (dev->chip->msi_en) {
+ if (dev->chip->msi_en)
pci_disable_msi(dev->pci);
- }
+ if (dev->remap_addr)
+ iounmap(dev->remap_addr);
- /* Tell the control thread to exit. The SCSI host must
- * already have been removed so it won't try to queue
- * any more commands.
- */
- printk(KERN_INFO "-- sending exit command to thread\n");
- up(&dev->sema);
+ pci_disable_device(dev->pci);
+ pci_release_regions(dev->pci);
+
+ rtsx_release_chip(dev->chip);
+ kfree(dev->chip);
}
/* First stage of disconnect processing: stop all commands and remove
scsi_unlock(host);
mutex_unlock(&dev->dev_mutex);
wake_up(&dev->delay_wait);
+ wait_for_completion(&dev->scanning_done);
/* Wait some time to let other threads exist */
wait_timeout(100);
/* Should we unbind if no devices were detected? */
}
- scsi_host_put(rtsx_to_host(dev));
- complete_and_exit(&threads_gone, 0);
+ complete_and_exit(&dev->scanning_done, 0);
}
static void rtsx_init_options(struct rtsx_chip *chip)
spin_lock_init(&dev->reg_lock);
mutex_init(&(dev->dev_mutex));
- sema_init(&(dev->sema), 0);
+ init_completion(&dev->cmnd_ready);
+ init_completion(&dev->control_exit);
+ init_completion(&dev->polling_exit);
init_completion(&(dev->notify));
+ init_completion(&dev->scanning_done);
init_waitqueue_head(&dev->delay_wait);
dev->pci = pci;
pci_set_master(pci);
synchronize_irq(dev->irq);
- err = scsi_add_host(host, &pci->dev);
- if (err) {
- printk(KERN_ERR "Unable to add the scsi host\n");
- goto errout;
- }
-
rtsx_init_chip(dev->chip);
/* Start up our control thread */
- th = kthread_create(rtsx_control_thread, dev, CR_DRIVER_NAME);
+ th = kthread_run(rtsx_control_thread, dev, CR_DRIVER_NAME);
if (IS_ERR(th)) {
printk(KERN_ERR "Unable to start control thread\n");
err = PTR_ERR(th);
goto errout;
}
+ dev->ctl_thread = th;
- /* Take a reference to the host for the control thread and
- * count it among all the threads we have launched. Then
- * start it up. */
- scsi_host_get(rtsx_to_host(dev));
- atomic_inc(&total_threads);
- wake_up_process(th);
+ err = scsi_add_host(host, &pci->dev);
+ if (err) {
+ printk(KERN_ERR "Unable to add the scsi host\n");
+ goto errout;
+ }
/* Start up the thread for delayed SCSI-device scanning */
th = kthread_create(rtsx_scan_thread, dev, "rtsx-scan");
goto errout;
}
- /* Take a reference to the host for the scanning thread and
- * count it among all the threads we have launched. Then
- * start it up. */
- scsi_host_get(rtsx_to_host(dev));
- atomic_inc(&total_threads);
wake_up_process(th);
/* Start up the thread for polling thread */
- th = kthread_create(rtsx_polling_thread, dev, "rtsx-polling");
+ th = kthread_run(rtsx_polling_thread, dev, "rtsx-polling");
if (IS_ERR(th)) {
printk(KERN_ERR "Unable to start the device-polling thread\n");
quiesce_and_remove_host(dev);
err = PTR_ERR(th);
goto errout;
}
-
- /* Take a reference to the host for the polling thread and
- * count it among all the threads we have launched. Then
- * start it up. */
- scsi_host_get(rtsx_to_host(dev));
- atomic_inc(&total_threads);
- wake_up_process(th);
+ dev->polling_thread = th;
pci_set_drvdata(pci, dev);
pci_unregister_driver(&driver);
- /* Don't return until all of our control and scanning threads
- * have exited. Since each thread signals threads_gone as its
- * last act, we have to call wait_for_completion the right number
- * of times.
- */
- while (atomic_read(&total_threads) > 0) {
- wait_for_completion(&threads_gone);
- atomic_dec(&total_threads);
- }
-
printk(KERN_INFO "%s module exit\n", CR_DRIVER_NAME);
}
/* locks */
spinlock_t reg_lock;
+ struct task_struct *ctl_thread; /* the control thread */
+ struct task_struct *polling_thread; /* the polling thread */
+
/* mutual exclusion and synchronization structures */
- struct semaphore sema; /* to sleep thread on */
+ struct completion cmnd_ready; /* to sleep thread on */
+ struct completion control_exit; /* control thread exit */
+ struct completion polling_exit; /* polling thread exit */
struct completion notify; /* thread begin/end */
+ struct completion scanning_done; /* wait for scan thread */
+
wait_queue_head_t delay_wait; /* wait during scan, reset */
struct mutex dev_mutex;
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/interrupt.h>
+#include <linux/slab.h>
#include <linux/videodev2.h>
#include "solo6x10.h"
#include "tw28.h"
*/
#include <linux/kernel.h>
+#include <linux/slab.h>
#include "solo6x10.h"
#include "osd-font.h"
#include <linux/mempool.h>
#include <linux/poll.h>
#include <linux/kthread.h>
+#include <linux/slab.h>
#include <linux/freezer.h>
#include <sound/core.h>
#include <sound/initval.h>
*/
#include <linux/kernel.h>
+#include <linux/slab.h>
#include <linux/scatterlist.h>
#include "solo6x10.h"
#include <linux/list.h>
#include <linux/wait.h>
#include <linux/delay.h>
+#include <linux/slab.h>
#include <asm/io.h>
#include <linux/atomic.h>
#include <linux/videodev2.h>
{
size_t count = nbytes;
const char *ptr = buffer;
- int bytes;
+ size_t bytes;
unsigned long flags;
u_char buf[256];
+
if (synth == NULL)
return -ENODEV;
while (count > 0) {
- bytes = min_t(size_t, count, sizeof(buf));
+ bytes = min(count, sizeof(buf));
if (copy_from_user(buf, ptr, bytes))
return -EFAULT;
count -= bytes;
-zcache-y := tmem.o
+zcache-y := zcache-main.o tmem.o
obj-$(CONFIG_ZCACHE) += zcache.o
--- /dev/null
+/*
+ * zcache.c
+ *
+ * Copyright (c) 2010,2011, Dan Magenheimer, Oracle Corp.
+ * Copyright (c) 2010,2011, Nitin Gupta
+ *
+ * Zcache provides an in-kernel "host implementation" for transcendent memory
+ * and, thus indirectly, for cleancache and frontswap. Zcache includes two
+ * page-accessible memory [1] interfaces, both utilizing lzo1x compression:
+ * 1) "compression buddies" ("zbud") is used for ephemeral pages
+ * 2) xvmalloc is used for persistent pages.
+ * Xvmalloc (based on the TLSF allocator) has very low fragmentation
+ * so maximizes space efficiency, while zbud allows pairs (and potentially,
+ * in the future, more than a pair of) compressed pages to be closely linked
+ * so that reclaiming can be done via the kernel's physical-page-oriented
+ * "shrinker" interface.
+ *
+ * [1] For a definition of page-accessible memory (aka PAM), see:
+ * http://marc.info/?l=linux-mm&m=127811271605009
+ */
+
+#include <linux/module.h>
+#include <linux/cpu.h>
+#include <linux/highmem.h>
+#include <linux/list.h>
+#include <linux/lzo.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/atomic.h>
+#include <linux/math64.h>
+#include "tmem.h"
+
+#include "../zram/xvmalloc.h" /* if built in drivers/staging */
+
+#if (!defined(CONFIG_CLEANCACHE) && !defined(CONFIG_FRONTSWAP))
+#error "zcache is useless without CONFIG_CLEANCACHE or CONFIG_FRONTSWAP"
+#endif
+#ifdef CONFIG_CLEANCACHE
+#include <linux/cleancache.h>
+#endif
+#ifdef CONFIG_FRONTSWAP
+#include <linux/frontswap.h>
+#endif
+
+#if 0
+/* this is more aggressive but may cause other problems? */
+#define ZCACHE_GFP_MASK (GFP_ATOMIC | __GFP_NORETRY | __GFP_NOWARN)
+#else
+#define ZCACHE_GFP_MASK \
+ (__GFP_FS | __GFP_NORETRY | __GFP_NOWARN | __GFP_NOMEMALLOC)
+#endif
+
+#define MAX_POOLS_PER_CLIENT 16
+
+#define MAX_CLIENTS 16
+#define LOCAL_CLIENT ((uint16_t)-1)
+
+MODULE_LICENSE("GPL");
+
+struct zcache_client {
+ struct tmem_pool *tmem_pools[MAX_POOLS_PER_CLIENT];
+ struct xv_pool *xvpool;
+ bool allocated;
+ atomic_t refcount;
+};
+
+static struct zcache_client zcache_host;
+static struct zcache_client zcache_clients[MAX_CLIENTS];
+
+static inline uint16_t get_client_id_from_client(struct zcache_client *cli)
+{
+ BUG_ON(cli == NULL);
+ if (cli == &zcache_host)
+ return LOCAL_CLIENT;
+ return cli - &zcache_clients[0];
+}
+
+static inline bool is_local_client(struct zcache_client *cli)
+{
+ return cli == &zcache_host;
+}
+
+/**********
+ * Compression buddies ("zbud") provides for packing two (or, possibly
+ * in the future, more) compressed ephemeral pages into a single "raw"
+ * (physical) page and tracking them with data structures so that
+ * the raw pages can be easily reclaimed.
+ *
+ * A zbud page ("zbpg") is an aligned page containing a list_head,
+ * a lock, and two "zbud headers". The remainder of the physical
+ * page is divided up into aligned 64-byte "chunks" which contain
+ * the compressed data for zero, one, or two zbuds. Each zbpg
+ * resides on: (1) an "unused list" if it has no zbuds; (2) a
+ * "buddied" list if it is fully populated with two zbuds; or
+ * (3) one of PAGE_SIZE/64 "unbuddied" lists indexed by how many chunks
+ * the one unbuddied zbud uses. The data inside a zbpg cannot be
+ * read or written unless the zbpg's lock is held.
+ */
+
+#define ZBH_SENTINEL 0x43214321
+#define ZBPG_SENTINEL 0xdeadbeef
+
+#define ZBUD_MAX_BUDS 2
+
+struct zbud_hdr {
+ uint16_t client_id;
+ uint16_t pool_id;
+ struct tmem_oid oid;
+ uint32_t index;
+ uint16_t size; /* compressed size in bytes, zero means unused */
+ DECL_SENTINEL
+};
+
+struct zbud_page {
+ struct list_head bud_list;
+ spinlock_t lock;
+ struct zbud_hdr buddy[ZBUD_MAX_BUDS];
+ DECL_SENTINEL
+ /* followed by NUM_CHUNK aligned CHUNK_SIZE-byte chunks */
+};
+
+#define CHUNK_SHIFT 6
+#define CHUNK_SIZE (1 << CHUNK_SHIFT)
+#define CHUNK_MASK (~(CHUNK_SIZE-1))
+#define NCHUNKS (((PAGE_SIZE - sizeof(struct zbud_page)) & \
+ CHUNK_MASK) >> CHUNK_SHIFT)
+#define MAX_CHUNK (NCHUNKS-1)
+
+static struct {
+ struct list_head list;
+ unsigned count;
+} zbud_unbuddied[NCHUNKS];
+/* list N contains pages with N chunks USED and NCHUNKS-N unused */
+/* element 0 is never used but optimizing that isn't worth it */
+static unsigned long zbud_cumul_chunk_counts[NCHUNKS];
+
+struct list_head zbud_buddied_list;
+static unsigned long zcache_zbud_buddied_count;
+
+/* protects the buddied list and all unbuddied lists */
+static DEFINE_SPINLOCK(zbud_budlists_spinlock);
+
+static LIST_HEAD(zbpg_unused_list);
+static unsigned long zcache_zbpg_unused_list_count;
+
+/* protects the unused page list */
+static DEFINE_SPINLOCK(zbpg_unused_list_spinlock);
+
+static atomic_t zcache_zbud_curr_raw_pages;
+static atomic_t zcache_zbud_curr_zpages;
+static unsigned long zcache_zbud_curr_zbytes;
+static unsigned long zcache_zbud_cumul_zpages;
+static unsigned long zcache_zbud_cumul_zbytes;
+static unsigned long zcache_compress_poor;
+static unsigned long zcache_mean_compress_poor;
+
+/* forward references */
+static void *zcache_get_free_page(void);
+static void zcache_free_page(void *p);
+
+/*
+ * zbud helper functions
+ */
+
+static inline unsigned zbud_max_buddy_size(void)
+{
+ return MAX_CHUNK << CHUNK_SHIFT;
+}
+
+static inline unsigned zbud_size_to_chunks(unsigned size)
+{
+ BUG_ON(size == 0 || size > zbud_max_buddy_size());
+ return (size + CHUNK_SIZE - 1) >> CHUNK_SHIFT;
+}
+
+static inline int zbud_budnum(struct zbud_hdr *zh)
+{
+ unsigned offset = (unsigned long)zh & (PAGE_SIZE - 1);
+ struct zbud_page *zbpg = NULL;
+ unsigned budnum = -1U;
+ int i;
+
+ for (i = 0; i < ZBUD_MAX_BUDS; i++)
+ if (offset == offsetof(typeof(*zbpg), buddy[i])) {
+ budnum = i;
+ break;
+ }
+ BUG_ON(budnum == -1U);
+ return budnum;
+}
+
+static char *zbud_data(struct zbud_hdr *zh, unsigned size)
+{
+ struct zbud_page *zbpg;
+ char *p;
+ unsigned budnum;
+
+ ASSERT_SENTINEL(zh, ZBH);
+ budnum = zbud_budnum(zh);
+ BUG_ON(size == 0 || size > zbud_max_buddy_size());
+ zbpg = container_of(zh, struct zbud_page, buddy[budnum]);
+ ASSERT_SPINLOCK(&zbpg->lock);
+ p = (char *)zbpg;
+ if (budnum == 0)
+ p += ((sizeof(struct zbud_page) + CHUNK_SIZE - 1) &
+ CHUNK_MASK);
+ else if (budnum == 1)
+ p += PAGE_SIZE - ((size + CHUNK_SIZE - 1) & CHUNK_MASK);
+ return p;
+}
+
+/*
+ * zbud raw page management
+ */
+
+static struct zbud_page *zbud_alloc_raw_page(void)
+{
+ struct zbud_page *zbpg = NULL;
+ struct zbud_hdr *zh0, *zh1;
+ bool recycled = 0;
+
+ /* if any pages on the zbpg list, use one */
+ spin_lock(&zbpg_unused_list_spinlock);
+ if (!list_empty(&zbpg_unused_list)) {
+ zbpg = list_first_entry(&zbpg_unused_list,
+ struct zbud_page, bud_list);
+ list_del_init(&zbpg->bud_list);
+ zcache_zbpg_unused_list_count--;
+ recycled = 1;
+ }
+ spin_unlock(&zbpg_unused_list_spinlock);
+ if (zbpg == NULL)
+ /* none on zbpg list, try to get a kernel page */
+ zbpg = zcache_get_free_page();
+ if (likely(zbpg != NULL)) {
+ INIT_LIST_HEAD(&zbpg->bud_list);
+ zh0 = &zbpg->buddy[0]; zh1 = &zbpg->buddy[1];
+ spin_lock_init(&zbpg->lock);
+ if (recycled) {
+ ASSERT_INVERTED_SENTINEL(zbpg, ZBPG);
+ SET_SENTINEL(zbpg, ZBPG);
+ BUG_ON(zh0->size != 0 || tmem_oid_valid(&zh0->oid));
+ BUG_ON(zh1->size != 0 || tmem_oid_valid(&zh1->oid));
+ } else {
+ atomic_inc(&zcache_zbud_curr_raw_pages);
+ INIT_LIST_HEAD(&zbpg->bud_list);
+ SET_SENTINEL(zbpg, ZBPG);
+ zh0->size = 0; zh1->size = 0;
+ tmem_oid_set_invalid(&zh0->oid);
+ tmem_oid_set_invalid(&zh1->oid);
+ }
+ }
+ return zbpg;
+}
+
+static void zbud_free_raw_page(struct zbud_page *zbpg)
+{
+ struct zbud_hdr *zh0 = &zbpg->buddy[0], *zh1 = &zbpg->buddy[1];
+
+ ASSERT_SENTINEL(zbpg, ZBPG);
+ BUG_ON(!list_empty(&zbpg->bud_list));
+ ASSERT_SPINLOCK(&zbpg->lock);
+ BUG_ON(zh0->size != 0 || tmem_oid_valid(&zh0->oid));
+ BUG_ON(zh1->size != 0 || tmem_oid_valid(&zh1->oid));
+ INVERT_SENTINEL(zbpg, ZBPG);
+ spin_unlock(&zbpg->lock);
+ spin_lock(&zbpg_unused_list_spinlock);
+ list_add(&zbpg->bud_list, &zbpg_unused_list);
+ zcache_zbpg_unused_list_count++;
+ spin_unlock(&zbpg_unused_list_spinlock);
+}
+
+/*
+ * core zbud handling routines
+ */
+
+static unsigned zbud_free(struct zbud_hdr *zh)
+{
+ unsigned size;
+
+ ASSERT_SENTINEL(zh, ZBH);
+ BUG_ON(!tmem_oid_valid(&zh->oid));
+ size = zh->size;
+ BUG_ON(zh->size == 0 || zh->size > zbud_max_buddy_size());
+ zh->size = 0;
+ tmem_oid_set_invalid(&zh->oid);
+ INVERT_SENTINEL(zh, ZBH);
+ zcache_zbud_curr_zbytes -= size;
+ atomic_dec(&zcache_zbud_curr_zpages);
+ return size;
+}
+
+static void zbud_free_and_delist(struct zbud_hdr *zh)
+{
+ unsigned chunks;
+ struct zbud_hdr *zh_other;
+ unsigned budnum = zbud_budnum(zh), size;
+ struct zbud_page *zbpg =
+ container_of(zh, struct zbud_page, buddy[budnum]);
+
+ spin_lock(&zbpg->lock);
+ if (list_empty(&zbpg->bud_list)) {
+ /* ignore zombie page... see zbud_evict_pages() */
+ spin_unlock(&zbpg->lock);
+ return;
+ }
+ size = zbud_free(zh);
+ ASSERT_SPINLOCK(&zbpg->lock);
+ zh_other = &zbpg->buddy[(budnum == 0) ? 1 : 0];
+ if (zh_other->size == 0) { /* was unbuddied: unlist and free */
+ chunks = zbud_size_to_chunks(size) ;
+ spin_lock(&zbud_budlists_spinlock);
+ BUG_ON(list_empty(&zbud_unbuddied[chunks].list));
+ list_del_init(&zbpg->bud_list);
+ zbud_unbuddied[chunks].count--;
+ spin_unlock(&zbud_budlists_spinlock);
+ zbud_free_raw_page(zbpg);
+ } else { /* was buddied: move remaining buddy to unbuddied list */
+ chunks = zbud_size_to_chunks(zh_other->size) ;
+ spin_lock(&zbud_budlists_spinlock);
+ list_del_init(&zbpg->bud_list);
+ zcache_zbud_buddied_count--;
+ list_add_tail(&zbpg->bud_list, &zbud_unbuddied[chunks].list);
+ zbud_unbuddied[chunks].count++;
+ spin_unlock(&zbud_budlists_spinlock);
+ spin_unlock(&zbpg->lock);
+ }
+}
+
+static struct zbud_hdr *zbud_create(uint16_t client_id, uint16_t pool_id,
+ struct tmem_oid *oid,
+ uint32_t index, struct page *page,
+ void *cdata, unsigned size)
+{
+ struct zbud_hdr *zh0, *zh1, *zh = NULL;
+ struct zbud_page *zbpg = NULL, *ztmp;
+ unsigned nchunks;
+ char *to;
+ int i, found_good_buddy = 0;
+
+ nchunks = zbud_size_to_chunks(size) ;
+ for (i = MAX_CHUNK - nchunks + 1; i > 0; i--) {
+ spin_lock(&zbud_budlists_spinlock);
+ if (!list_empty(&zbud_unbuddied[i].list)) {
+ list_for_each_entry_safe(zbpg, ztmp,
+ &zbud_unbuddied[i].list, bud_list) {
+ if (spin_trylock(&zbpg->lock)) {
+ found_good_buddy = i;
+ goto found_unbuddied;
+ }
+ }
+ }
+ spin_unlock(&zbud_budlists_spinlock);
+ }
+ /* didn't find a good buddy, try allocating a new page */
+ zbpg = zbud_alloc_raw_page();
+ if (unlikely(zbpg == NULL))
+ goto out;
+ /* ok, have a page, now compress the data before taking locks */
+ spin_lock(&zbpg->lock);
+ spin_lock(&zbud_budlists_spinlock);
+ list_add_tail(&zbpg->bud_list, &zbud_unbuddied[nchunks].list);
+ zbud_unbuddied[nchunks].count++;
+ zh = &zbpg->buddy[0];
+ goto init_zh;
+
+found_unbuddied:
+ ASSERT_SPINLOCK(&zbpg->lock);
+ zh0 = &zbpg->buddy[0]; zh1 = &zbpg->buddy[1];
+ BUG_ON(!((zh0->size == 0) ^ (zh1->size == 0)));
+ if (zh0->size != 0) { /* buddy0 in use, buddy1 is vacant */
+ ASSERT_SENTINEL(zh0, ZBH);
+ zh = zh1;
+ } else if (zh1->size != 0) { /* buddy1 in use, buddy0 is vacant */
+ ASSERT_SENTINEL(zh1, ZBH);
+ zh = zh0;
+ } else
+ BUG();
+ list_del_init(&zbpg->bud_list);
+ zbud_unbuddied[found_good_buddy].count--;
+ list_add_tail(&zbpg->bud_list, &zbud_buddied_list);
+ zcache_zbud_buddied_count++;
+
+init_zh:
+ SET_SENTINEL(zh, ZBH);
+ zh->size = size;
+ zh->index = index;
+ zh->oid = *oid;
+ zh->pool_id = pool_id;
+ zh->client_id = client_id;
+ /* can wait to copy the data until the list locks are dropped */
+ spin_unlock(&zbud_budlists_spinlock);
+
+ to = zbud_data(zh, size);
+ memcpy(to, cdata, size);
+ spin_unlock(&zbpg->lock);
+ zbud_cumul_chunk_counts[nchunks]++;
+ atomic_inc(&zcache_zbud_curr_zpages);
+ zcache_zbud_cumul_zpages++;
+ zcache_zbud_curr_zbytes += size;
+ zcache_zbud_cumul_zbytes += size;
+out:
+ return zh;
+}
+
+static int zbud_decompress(struct page *page, struct zbud_hdr *zh)
+{
+ struct zbud_page *zbpg;
+ unsigned budnum = zbud_budnum(zh);
+ size_t out_len = PAGE_SIZE;
+ char *to_va, *from_va;
+ unsigned size;
+ int ret = 0;
+
+ zbpg = container_of(zh, struct zbud_page, buddy[budnum]);
+ spin_lock(&zbpg->lock);
+ if (list_empty(&zbpg->bud_list)) {
+ /* ignore zombie page... see zbud_evict_pages() */
+ ret = -EINVAL;
+ goto out;
+ }
+ ASSERT_SENTINEL(zh, ZBH);
+ BUG_ON(zh->size == 0 || zh->size > zbud_max_buddy_size());
+ to_va = kmap_atomic(page, KM_USER0);
+ size = zh->size;
+ from_va = zbud_data(zh, size);
+ ret = lzo1x_decompress_safe(from_va, size, to_va, &out_len);
+ BUG_ON(ret != LZO_E_OK);
+ BUG_ON(out_len != PAGE_SIZE);
+ kunmap_atomic(to_va, KM_USER0);
+out:
+ spin_unlock(&zbpg->lock);
+ return ret;
+}
+
+/*
+ * The following routines handle shrinking of ephemeral pages by evicting
+ * pages "least valuable" first.
+ */
+
+static unsigned long zcache_evicted_raw_pages;
+static unsigned long zcache_evicted_buddied_pages;
+static unsigned long zcache_evicted_unbuddied_pages;
+
+static struct tmem_pool *zcache_get_pool_by_id(uint16_t cli_id,
+ uint16_t poolid);
+static void zcache_put_pool(struct tmem_pool *pool);
+
+/*
+ * Flush and free all zbuds in a zbpg, then free the pageframe
+ */
+static void zbud_evict_zbpg(struct zbud_page *zbpg)
+{
+ struct zbud_hdr *zh;
+ int i, j;
+ uint32_t pool_id[ZBUD_MAX_BUDS], client_id[ZBUD_MAX_BUDS];
+ uint32_t index[ZBUD_MAX_BUDS];
+ struct tmem_oid oid[ZBUD_MAX_BUDS];
+ struct tmem_pool *pool;
+
+ ASSERT_SPINLOCK(&zbpg->lock);
+ BUG_ON(!list_empty(&zbpg->bud_list));
+ for (i = 0, j = 0; i < ZBUD_MAX_BUDS; i++) {
+ zh = &zbpg->buddy[i];
+ if (zh->size) {
+ client_id[j] = zh->client_id;
+ pool_id[j] = zh->pool_id;
+ oid[j] = zh->oid;
+ index[j] = zh->index;
+ j++;
+ zbud_free(zh);
+ }
+ }
+ spin_unlock(&zbpg->lock);
+ for (i = 0; i < j; i++) {
+ pool = zcache_get_pool_by_id(client_id[i], pool_id[i]);
+ if (pool != NULL) {
+ tmem_flush_page(pool, &oid[i], index[i]);
+ zcache_put_pool(pool);
+ }
+ }
+ ASSERT_SENTINEL(zbpg, ZBPG);
+ spin_lock(&zbpg->lock);
+ zbud_free_raw_page(zbpg);
+}
+
+/*
+ * Free nr pages. This code is funky because we want to hold the locks
+ * protecting various lists for as short a time as possible, and in some
+ * circumstances the list may change asynchronously when the list lock is
+ * not held. In some cases we also trylock not only to avoid waiting on a
+ * page in use by another cpu, but also to avoid potential deadlock due to
+ * lock inversion.
+ */
+static void zbud_evict_pages(int nr)
+{
+ struct zbud_page *zbpg;
+ int i;
+
+ /* first try freeing any pages on unused list */
+retry_unused_list:
+ spin_lock_bh(&zbpg_unused_list_spinlock);
+ if (!list_empty(&zbpg_unused_list)) {
+ /* can't walk list here, since it may change when unlocked */
+ zbpg = list_first_entry(&zbpg_unused_list,
+ struct zbud_page, bud_list);
+ list_del_init(&zbpg->bud_list);
+ zcache_zbpg_unused_list_count--;
+ atomic_dec(&zcache_zbud_curr_raw_pages);
+ spin_unlock_bh(&zbpg_unused_list_spinlock);
+ zcache_free_page(zbpg);
+ zcache_evicted_raw_pages++;
+ if (--nr <= 0)
+ goto out;
+ goto retry_unused_list;
+ }
+ spin_unlock_bh(&zbpg_unused_list_spinlock);
+
+ /* now try freeing unbuddied pages, starting with least space avail */
+ for (i = 0; i < MAX_CHUNK; i++) {
+retry_unbud_list_i:
+ spin_lock_bh(&zbud_budlists_spinlock);
+ if (list_empty(&zbud_unbuddied[i].list)) {
+ spin_unlock_bh(&zbud_budlists_spinlock);
+ continue;
+ }
+ list_for_each_entry(zbpg, &zbud_unbuddied[i].list, bud_list) {
+ if (unlikely(!spin_trylock(&zbpg->lock)))
+ continue;
+ list_del_init(&zbpg->bud_list);
+ zbud_unbuddied[i].count--;
+ spin_unlock(&zbud_budlists_spinlock);
+ zcache_evicted_unbuddied_pages++;
+ /* want budlists unlocked when doing zbpg eviction */
+ zbud_evict_zbpg(zbpg);
+ local_bh_enable();
+ if (--nr <= 0)
+ goto out;
+ goto retry_unbud_list_i;
+ }
+ spin_unlock_bh(&zbud_budlists_spinlock);
+ }
+
+ /* as a last resort, free buddied pages */
+retry_bud_list:
+ spin_lock_bh(&zbud_budlists_spinlock);
+ if (list_empty(&zbud_buddied_list)) {
+ spin_unlock_bh(&zbud_budlists_spinlock);
+ goto out;
+ }
+ list_for_each_entry(zbpg, &zbud_buddied_list, bud_list) {
+ if (unlikely(!spin_trylock(&zbpg->lock)))
+ continue;
+ list_del_init(&zbpg->bud_list);
+ zcache_zbud_buddied_count--;
+ spin_unlock(&zbud_budlists_spinlock);
+ zcache_evicted_buddied_pages++;
+ /* want budlists unlocked when doing zbpg eviction */
+ zbud_evict_zbpg(zbpg);
+ local_bh_enable();
+ if (--nr <= 0)
+ goto out;
+ goto retry_bud_list;
+ }
+ spin_unlock_bh(&zbud_budlists_spinlock);
+out:
+ return;
+}
+
+static void zbud_init(void)
+{
+ int i;
+
+ INIT_LIST_HEAD(&zbud_buddied_list);
+ zcache_zbud_buddied_count = 0;
+ for (i = 0; i < NCHUNKS; i++) {
+ INIT_LIST_HEAD(&zbud_unbuddied[i].list);
+ zbud_unbuddied[i].count = 0;
+ }
+}
+
+#ifdef CONFIG_SYSFS
+/*
+ * These sysfs routines show a nice distribution of how many zbpg's are
+ * currently (and have ever been placed) in each unbuddied list. It's fun
+ * to watch but can probably go away before final merge.
+ */
+static int zbud_show_unbuddied_list_counts(char *buf)
+{
+ int i;
+ char *p = buf;
+
+ for (i = 0; i < NCHUNKS; i++)
+ p += sprintf(p, "%u ", zbud_unbuddied[i].count);
+ return p - buf;
+}
+
+static int zbud_show_cumul_chunk_counts(char *buf)
+{
+ unsigned long i, chunks = 0, total_chunks = 0, sum_total_chunks = 0;
+ unsigned long total_chunks_lte_21 = 0, total_chunks_lte_32 = 0;
+ unsigned long total_chunks_lte_42 = 0;
+ char *p = buf;
+
+ for (i = 0; i < NCHUNKS; i++) {
+ p += sprintf(p, "%lu ", zbud_cumul_chunk_counts[i]);
+ chunks += zbud_cumul_chunk_counts[i];
+ total_chunks += zbud_cumul_chunk_counts[i];
+ sum_total_chunks += i * zbud_cumul_chunk_counts[i];
+ if (i == 21)
+ total_chunks_lte_21 = total_chunks;
+ if (i == 32)
+ total_chunks_lte_32 = total_chunks;
+ if (i == 42)
+ total_chunks_lte_42 = total_chunks;
+ }
+ p += sprintf(p, "<=21:%lu <=32:%lu <=42:%lu, mean:%lu\n",
+ total_chunks_lte_21, total_chunks_lte_32, total_chunks_lte_42,
+ chunks == 0 ? 0 : sum_total_chunks / chunks);
+ return p - buf;
+}
+#endif
+
+/**********
+ * This "zv" PAM implementation combines the TLSF-based xvMalloc
+ * with lzo1x compression to maximize the amount of data that can
+ * be packed into a physical page.
+ *
+ * Zv represents a PAM page with the index and object (plus a "size" value
+ * necessary for decompression) immediately preceding the compressed data.
+ */
+
+#define ZVH_SENTINEL 0x43214321
+
+struct zv_hdr {
+ uint32_t pool_id;
+ struct tmem_oid oid;
+ uint32_t index;
+ DECL_SENTINEL
+};
+
+/* rudimentary policy limits */
+/* total number of persistent pages may not exceed this percentage */
+static unsigned int zv_page_count_policy_percent = 75;
+/*
+ * byte count defining poor compression; pages with greater zsize will be
+ * rejected
+ */
+static unsigned int zv_max_zsize = (PAGE_SIZE / 8) * 7;
+/*
+ * byte count defining poor *mean* compression; pages with greater zsize
+ * will be rejected until sufficient better-compressed pages are accepted
+ * driving the man below this threshold
+ */
+static unsigned int zv_max_mean_zsize = (PAGE_SIZE / 8) * 5;
+
+static unsigned long zv_curr_dist_counts[NCHUNKS];
+static unsigned long zv_cumul_dist_counts[NCHUNKS];
+
+static struct zv_hdr *zv_create(struct xv_pool *xvpool, uint32_t pool_id,
+ struct tmem_oid *oid, uint32_t index,
+ void *cdata, unsigned clen)
+{
+ struct page *page;
+ struct zv_hdr *zv = NULL;
+ uint32_t offset;
+ int alloc_size = clen + sizeof(struct zv_hdr);
+ int chunks = (alloc_size + (CHUNK_SIZE - 1)) >> CHUNK_SHIFT;
+ int ret;
+
+ BUG_ON(!irqs_disabled());
+ BUG_ON(chunks >= NCHUNKS);
+ ret = xv_malloc(xvpool, alloc_size,
+ &page, &offset, ZCACHE_GFP_MASK);
+ if (unlikely(ret))
+ goto out;
+ zv_curr_dist_counts[chunks]++;
+ zv_cumul_dist_counts[chunks]++;
+ zv = kmap_atomic(page, KM_USER0) + offset;
+ zv->index = index;
+ zv->oid = *oid;
+ zv->pool_id = pool_id;
+ SET_SENTINEL(zv, ZVH);
+ memcpy((char *)zv + sizeof(struct zv_hdr), cdata, clen);
+ kunmap_atomic(zv, KM_USER0);
+out:
+ return zv;
+}
+
+static void zv_free(struct xv_pool *xvpool, struct zv_hdr *zv)
+{
+ unsigned long flags;
+ struct page *page;
+ uint32_t offset;
+ uint16_t size = xv_get_object_size(zv);
+ int chunks = (size + (CHUNK_SIZE - 1)) >> CHUNK_SHIFT;
+
+ ASSERT_SENTINEL(zv, ZVH);
+ BUG_ON(chunks >= NCHUNKS);
+ zv_curr_dist_counts[chunks]--;
+ size -= sizeof(*zv);
+ BUG_ON(size == 0);
+ INVERT_SENTINEL(zv, ZVH);
+ page = virt_to_page(zv);
+ offset = (unsigned long)zv & ~PAGE_MASK;
+ local_irq_save(flags);
+ xv_free(xvpool, page, offset);
+ local_irq_restore(flags);
+}
+
+static void zv_decompress(struct page *page, struct zv_hdr *zv)
+{
+ size_t clen = PAGE_SIZE;
+ char *to_va;
+ unsigned size;
+ int ret;
+
+ ASSERT_SENTINEL(zv, ZVH);
+ size = xv_get_object_size(zv) - sizeof(*zv);
+ BUG_ON(size == 0);
+ to_va = kmap_atomic(page, KM_USER0);
+ ret = lzo1x_decompress_safe((char *)zv + sizeof(*zv),
+ size, to_va, &clen);
+ kunmap_atomic(to_va, KM_USER0);
+ BUG_ON(ret != LZO_E_OK);
+ BUG_ON(clen != PAGE_SIZE);
+}
+
+#ifdef CONFIG_SYSFS
+/*
+ * show a distribution of compression stats for zv pages.
+ */
+
+static int zv_curr_dist_counts_show(char *buf)
+{
+ unsigned long i, n, chunks = 0, sum_total_chunks = 0;
+ char *p = buf;
+
+ for (i = 0; i < NCHUNKS; i++) {
+ n = zv_curr_dist_counts[i];
+ p += sprintf(p, "%lu ", n);
+ chunks += n;
+ sum_total_chunks += i * n;
+ }
+ p += sprintf(p, "mean:%lu\n",
+ chunks == 0 ? 0 : sum_total_chunks / chunks);
+ return p - buf;
+}
+
+static int zv_cumul_dist_counts_show(char *buf)
+{
+ unsigned long i, n, chunks = 0, sum_total_chunks = 0;
+ char *p = buf;
+
+ for (i = 0; i < NCHUNKS; i++) {
+ n = zv_cumul_dist_counts[i];
+ p += sprintf(p, "%lu ", n);
+ chunks += n;
+ sum_total_chunks += i * n;
+ }
+ p += sprintf(p, "mean:%lu\n",
+ chunks == 0 ? 0 : sum_total_chunks / chunks);
+ return p - buf;
+}
+
+/*
+ * setting zv_max_zsize via sysfs causes all persistent (e.g. swap)
+ * pages that don't compress to less than this value (including metadata
+ * overhead) to be rejected. We don't allow the value to get too close
+ * to PAGE_SIZE.
+ */
+static ssize_t zv_max_zsize_show(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ char *buf)
+{
+ return sprintf(buf, "%u\n", zv_max_zsize);
+}
+
+static ssize_t zv_max_zsize_store(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int err;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+ err = strict_strtoul(buf, 10, &val);
+ if (err || (val == 0) || (val > (PAGE_SIZE / 8) * 7))
+ return -EINVAL;
+ zv_max_zsize = val;
+ return count;
+}
+
+/*
+ * setting zv_max_mean_zsize via sysfs causes all persistent (e.g. swap)
+ * pages that don't compress to less than this value (including metadata
+ * overhead) to be rejected UNLESS the mean compression is also smaller
+ * than this value. In other words, we are load-balancing-by-zsize the
+ * accepted pages. Again, we don't allow the value to get too close
+ * to PAGE_SIZE.
+ */
+static ssize_t zv_max_mean_zsize_show(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ char *buf)
+{
+ return sprintf(buf, "%u\n", zv_max_mean_zsize);
+}
+
+static ssize_t zv_max_mean_zsize_store(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int err;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+ err = strict_strtoul(buf, 10, &val);
+ if (err || (val == 0) || (val > (PAGE_SIZE / 8) * 7))
+ return -EINVAL;
+ zv_max_mean_zsize = val;
+ return count;
+}
+
+/*
+ * setting zv_page_count_policy_percent via sysfs sets an upper bound of
+ * persistent (e.g. swap) pages that will be retained according to:
+ * (zv_page_count_policy_percent * totalram_pages) / 100)
+ * when that limit is reached, further puts will be rejected (until
+ * some pages have been flushed). Note that, due to compression,
+ * this number may exceed 100; it defaults to 75 and we set an
+ * arbitary limit of 150. A poor choice will almost certainly result
+ * in OOM's, so this value should only be changed prudently.
+ */
+static ssize_t zv_page_count_policy_percent_show(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ char *buf)
+{
+ return sprintf(buf, "%u\n", zv_page_count_policy_percent);
+}
+
+static ssize_t zv_page_count_policy_percent_store(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ const char *buf, size_t count)
+{
+ unsigned long val;
+ int err;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+ err = strict_strtoul(buf, 10, &val);
+ if (err || (val == 0) || (val > 150))
+ return -EINVAL;
+ zv_page_count_policy_percent = val;
+ return count;
+}
+
+static struct kobj_attribute zcache_zv_max_zsize_attr = {
+ .attr = { .name = "zv_max_zsize", .mode = 0644 },
+ .show = zv_max_zsize_show,
+ .store = zv_max_zsize_store,
+};
+
+static struct kobj_attribute zcache_zv_max_mean_zsize_attr = {
+ .attr = { .name = "zv_max_mean_zsize", .mode = 0644 },
+ .show = zv_max_mean_zsize_show,
+ .store = zv_max_mean_zsize_store,
+};
+
+static struct kobj_attribute zcache_zv_page_count_policy_percent_attr = {
+ .attr = { .name = "zv_page_count_policy_percent",
+ .mode = 0644 },
+ .show = zv_page_count_policy_percent_show,
+ .store = zv_page_count_policy_percent_store,
+};
+#endif
+
+/*
+ * zcache core code starts here
+ */
+
+/* useful stats not collected by cleancache or frontswap */
+static unsigned long zcache_flush_total;
+static unsigned long zcache_flush_found;
+static unsigned long zcache_flobj_total;
+static unsigned long zcache_flobj_found;
+static unsigned long zcache_failed_eph_puts;
+static unsigned long zcache_failed_pers_puts;
+
+/*
+ * Tmem operations assume the poolid implies the invoking client.
+ * Zcache only has one client (the kernel itself): LOCAL_CLIENT.
+ * RAMster has each client numbered by cluster node, and a KVM version
+ * of zcache would have one client per guest and each client might
+ * have a poolid==N.
+ */
+static struct tmem_pool *zcache_get_pool_by_id(uint16_t cli_id, uint16_t poolid)
+{
+ struct tmem_pool *pool = NULL;
+ struct zcache_client *cli = NULL;
+
+ if (cli_id == LOCAL_CLIENT)
+ cli = &zcache_host;
+ else {
+ if (cli_id >= MAX_CLIENTS)
+ goto out;
+ cli = &zcache_clients[cli_id];
+ if (cli == NULL)
+ goto out;
+ atomic_inc(&cli->refcount);
+ }
+ if (poolid < MAX_POOLS_PER_CLIENT) {
+ pool = cli->tmem_pools[poolid];
+ if (pool != NULL)
+ atomic_inc(&pool->refcount);
+ }
+out:
+ return pool;
+}
+
+static void zcache_put_pool(struct tmem_pool *pool)
+{
+ struct zcache_client *cli = NULL;
+
+ if (pool == NULL)
+ BUG();
+ cli = pool->client;
+ atomic_dec(&pool->refcount);
+ atomic_dec(&cli->refcount);
+}
+
+int zcache_new_client(uint16_t cli_id)
+{
+ struct zcache_client *cli = NULL;
+ int ret = -1;
+
+ if (cli_id == LOCAL_CLIENT)
+ cli = &zcache_host;
+ else if ((unsigned int)cli_id < MAX_CLIENTS)
+ cli = &zcache_clients[cli_id];
+ if (cli == NULL)
+ goto out;
+ if (cli->allocated)
+ goto out;
+ cli->allocated = 1;
+#ifdef CONFIG_FRONTSWAP
+ cli->xvpool = xv_create_pool();
+ if (cli->xvpool == NULL)
+ goto out;
+#endif
+ ret = 0;
+out:
+ return ret;
+}
+
+/* counters for debugging */
+static unsigned long zcache_failed_get_free_pages;
+static unsigned long zcache_failed_alloc;
+static unsigned long zcache_put_to_flush;
+static unsigned long zcache_aborted_preload;
+static unsigned long zcache_aborted_shrink;
+
+/*
+ * Ensure that memory allocation requests in zcache don't result
+ * in direct reclaim requests via the shrinker, which would cause
+ * an infinite loop. Maybe a GFP flag would be better?
+ */
+static DEFINE_SPINLOCK(zcache_direct_reclaim_lock);
+
+/*
+ * for now, used named slabs so can easily track usage; later can
+ * either just use kmalloc, or perhaps add a slab-like allocator
+ * to more carefully manage total memory utilization
+ */
+static struct kmem_cache *zcache_objnode_cache;
+static struct kmem_cache *zcache_obj_cache;
+static atomic_t zcache_curr_obj_count = ATOMIC_INIT(0);
+static unsigned long zcache_curr_obj_count_max;
+static atomic_t zcache_curr_objnode_count = ATOMIC_INIT(0);
+static unsigned long zcache_curr_objnode_count_max;
+
+/*
+ * to avoid memory allocation recursion (e.g. due to direct reclaim), we
+ * preload all necessary data structures so the hostops callbacks never
+ * actually do a malloc
+ */
+struct zcache_preload {
+ void *page;
+ struct tmem_obj *obj;
+ int nr;
+ struct tmem_objnode *objnodes[OBJNODE_TREE_MAX_PATH];
+};
+static DEFINE_PER_CPU(struct zcache_preload, zcache_preloads) = { 0, };
+
+static int zcache_do_preload(struct tmem_pool *pool)
+{
+ struct zcache_preload *kp;
+ struct tmem_objnode *objnode;
+ struct tmem_obj *obj;
+ void *page;
+ int ret = -ENOMEM;
+
+ if (unlikely(zcache_objnode_cache == NULL))
+ goto out;
+ if (unlikely(zcache_obj_cache == NULL))
+ goto out;
+ if (!spin_trylock(&zcache_direct_reclaim_lock)) {
+ zcache_aborted_preload++;
+ goto out;
+ }
+ preempt_disable();
+ kp = &__get_cpu_var(zcache_preloads);
+ while (kp->nr < ARRAY_SIZE(kp->objnodes)) {
+ preempt_enable_no_resched();
+ objnode = kmem_cache_alloc(zcache_objnode_cache,
+ ZCACHE_GFP_MASK);
+ if (unlikely(objnode == NULL)) {
+ zcache_failed_alloc++;
+ goto unlock_out;
+ }
+ preempt_disable();
+ kp = &__get_cpu_var(zcache_preloads);
+ if (kp->nr < ARRAY_SIZE(kp->objnodes))
+ kp->objnodes[kp->nr++] = objnode;
+ else
+ kmem_cache_free(zcache_objnode_cache, objnode);
+ }
+ preempt_enable_no_resched();
+ obj = kmem_cache_alloc(zcache_obj_cache, ZCACHE_GFP_MASK);
+ if (unlikely(obj == NULL)) {
+ zcache_failed_alloc++;
+ goto unlock_out;
+ }
+ page = (void *)__get_free_page(ZCACHE_GFP_MASK);
+ if (unlikely(page == NULL)) {
+ zcache_failed_get_free_pages++;
+ kmem_cache_free(zcache_obj_cache, obj);
+ goto unlock_out;
+ }
+ preempt_disable();
+ kp = &__get_cpu_var(zcache_preloads);
+ if (kp->obj == NULL)
+ kp->obj = obj;
+ else
+ kmem_cache_free(zcache_obj_cache, obj);
+ if (kp->page == NULL)
+ kp->page = page;
+ else
+ free_page((unsigned long)page);
+ ret = 0;
+unlock_out:
+ spin_unlock(&zcache_direct_reclaim_lock);
+out:
+ return ret;
+}
+
+static void *zcache_get_free_page(void)
+{
+ struct zcache_preload *kp;
+ void *page;
+
+ kp = &__get_cpu_var(zcache_preloads);
+ page = kp->page;
+ BUG_ON(page == NULL);
+ kp->page = NULL;
+ return page;
+}
+
+static void zcache_free_page(void *p)
+{
+ free_page((unsigned long)p);
+}
+
+/*
+ * zcache implementation for tmem host ops
+ */
+
+static struct tmem_objnode *zcache_objnode_alloc(struct tmem_pool *pool)
+{
+ struct tmem_objnode *objnode = NULL;
+ unsigned long count;
+ struct zcache_preload *kp;
+
+ kp = &__get_cpu_var(zcache_preloads);
+ if (kp->nr <= 0)
+ goto out;
+ objnode = kp->objnodes[kp->nr - 1];
+ BUG_ON(objnode == NULL);
+ kp->objnodes[kp->nr - 1] = NULL;
+ kp->nr--;
+ count = atomic_inc_return(&zcache_curr_objnode_count);
+ if (count > zcache_curr_objnode_count_max)
+ zcache_curr_objnode_count_max = count;
+out:
+ return objnode;
+}
+
+static void zcache_objnode_free(struct tmem_objnode *objnode,
+ struct tmem_pool *pool)
+{
+ atomic_dec(&zcache_curr_objnode_count);
+ BUG_ON(atomic_read(&zcache_curr_objnode_count) < 0);
+ kmem_cache_free(zcache_objnode_cache, objnode);
+}
+
+static struct tmem_obj *zcache_obj_alloc(struct tmem_pool *pool)
+{
+ struct tmem_obj *obj = NULL;
+ unsigned long count;
+ struct zcache_preload *kp;
+
+ kp = &__get_cpu_var(zcache_preloads);
+ obj = kp->obj;
+ BUG_ON(obj == NULL);
+ kp->obj = NULL;
+ count = atomic_inc_return(&zcache_curr_obj_count);
+ if (count > zcache_curr_obj_count_max)
+ zcache_curr_obj_count_max = count;
+ return obj;
+}
+
+static void zcache_obj_free(struct tmem_obj *obj, struct tmem_pool *pool)
+{
+ atomic_dec(&zcache_curr_obj_count);
+ BUG_ON(atomic_read(&zcache_curr_obj_count) < 0);
+ kmem_cache_free(zcache_obj_cache, obj);
+}
+
+static struct tmem_hostops zcache_hostops = {
+ .obj_alloc = zcache_obj_alloc,
+ .obj_free = zcache_obj_free,
+ .objnode_alloc = zcache_objnode_alloc,
+ .objnode_free = zcache_objnode_free,
+};
+
+/*
+ * zcache implementations for PAM page descriptor ops
+ */
+
+static atomic_t zcache_curr_eph_pampd_count = ATOMIC_INIT(0);
+static unsigned long zcache_curr_eph_pampd_count_max;
+static atomic_t zcache_curr_pers_pampd_count = ATOMIC_INIT(0);
+static unsigned long zcache_curr_pers_pampd_count_max;
+
+/* forward reference */
+static int zcache_compress(struct page *from, void **out_va, size_t *out_len);
+
+static void *zcache_pampd_create(char *data, size_t size, bool raw, int eph,
+ struct tmem_pool *pool, struct tmem_oid *oid,
+ uint32_t index)
+{
+ void *pampd = NULL, *cdata;
+ size_t clen;
+ int ret;
+ unsigned long count;
+ struct page *page = virt_to_page(data);
+ struct zcache_client *cli = pool->client;
+ uint16_t client_id = get_client_id_from_client(cli);
+ unsigned long zv_mean_zsize;
+ unsigned long curr_pers_pampd_count;
+ u64 total_zsize;
+
+ if (eph) {
+ ret = zcache_compress(page, &cdata, &clen);
+ if (ret == 0)
+ goto out;
+ if (clen == 0 || clen > zbud_max_buddy_size()) {
+ zcache_compress_poor++;
+ goto out;
+ }
+ pampd = (void *)zbud_create(client_id, pool->pool_id, oid,
+ index, page, cdata, clen);
+ if (pampd != NULL) {
+ count = atomic_inc_return(&zcache_curr_eph_pampd_count);
+ if (count > zcache_curr_eph_pampd_count_max)
+ zcache_curr_eph_pampd_count_max = count;
+ }
+ } else {
+ curr_pers_pampd_count =
+ atomic_read(&zcache_curr_pers_pampd_count);
+ if (curr_pers_pampd_count >
+ (zv_page_count_policy_percent * totalram_pages) / 100)
+ goto out;
+ ret = zcache_compress(page, &cdata, &clen);
+ if (ret == 0)
+ goto out;
+ /* reject if compression is too poor */
+ if (clen > zv_max_zsize) {
+ zcache_compress_poor++;
+ goto out;
+ }
+ /* reject if mean compression is too poor */
+ if ((clen > zv_max_mean_zsize) && (curr_pers_pampd_count > 0)) {
+ total_zsize = xv_get_total_size_bytes(cli->xvpool);
+ zv_mean_zsize = div_u64(total_zsize,
+ curr_pers_pampd_count);
+ if (zv_mean_zsize > zv_max_mean_zsize) {
+ zcache_mean_compress_poor++;
+ goto out;
+ }
+ }
+ pampd = (void *)zv_create(cli->xvpool, pool->pool_id,
+ oid, index, cdata, clen);
+ if (pampd == NULL)
+ goto out;
+ count = atomic_inc_return(&zcache_curr_pers_pampd_count);
+ if (count > zcache_curr_pers_pampd_count_max)
+ zcache_curr_pers_pampd_count_max = count;
+ }
+out:
+ return pampd;
+}
+
+/*
+ * fill the pageframe corresponding to the struct page with the data
+ * from the passed pampd
+ */
+static int zcache_pampd_get_data(char *data, size_t *bufsize, bool raw,
+ void *pampd, struct tmem_pool *pool,
+ struct tmem_oid *oid, uint32_t index)
+{
+ int ret = 0;
+
+ BUG_ON(is_ephemeral(pool));
+ zv_decompress(virt_to_page(data), pampd);
+ return ret;
+}
+
+/*
+ * fill the pageframe corresponding to the struct page with the data
+ * from the passed pampd
+ */
+static int zcache_pampd_get_data_and_free(char *data, size_t *bufsize, bool raw,
+ void *pampd, struct tmem_pool *pool,
+ struct tmem_oid *oid, uint32_t index)
+{
+ int ret = 0;
+
+ BUG_ON(!is_ephemeral(pool));
+ zbud_decompress(virt_to_page(data), pampd);
+ zbud_free_and_delist((struct zbud_hdr *)pampd);
+ atomic_dec(&zcache_curr_eph_pampd_count);
+ return ret;
+}
+
+/*
+ * free the pampd and remove it from any zcache lists
+ * pampd must no longer be pointed to from any tmem data structures!
+ */
+static void zcache_pampd_free(void *pampd, struct tmem_pool *pool,
+ struct tmem_oid *oid, uint32_t index)
+{
+ struct zcache_client *cli = pool->client;
+
+ if (is_ephemeral(pool)) {
+ zbud_free_and_delist((struct zbud_hdr *)pampd);
+ atomic_dec(&zcache_curr_eph_pampd_count);
+ BUG_ON(atomic_read(&zcache_curr_eph_pampd_count) < 0);
+ } else {
+ zv_free(cli->xvpool, (struct zv_hdr *)pampd);
+ atomic_dec(&zcache_curr_pers_pampd_count);
+ BUG_ON(atomic_read(&zcache_curr_pers_pampd_count) < 0);
+ }
+}
+
+static void zcache_pampd_free_obj(struct tmem_pool *pool, struct tmem_obj *obj)
+{
+}
+
+static void zcache_pampd_new_obj(struct tmem_obj *obj)
+{
+}
+
+static int zcache_pampd_replace_in_obj(void *pampd, struct tmem_obj *obj)
+{
+ return -1;
+}
+
+static bool zcache_pampd_is_remote(void *pampd)
+{
+ return 0;
+}
+
+static struct tmem_pamops zcache_pamops = {
+ .create = zcache_pampd_create,
+ .get_data = zcache_pampd_get_data,
+ .get_data_and_free = zcache_pampd_get_data_and_free,
+ .free = zcache_pampd_free,
+ .free_obj = zcache_pampd_free_obj,
+ .new_obj = zcache_pampd_new_obj,
+ .replace_in_obj = zcache_pampd_replace_in_obj,
+ .is_remote = zcache_pampd_is_remote,
+};
+
+/*
+ * zcache compression/decompression and related per-cpu stuff
+ */
+
+#define LZO_WORKMEM_BYTES LZO1X_1_MEM_COMPRESS
+#define LZO_DSTMEM_PAGE_ORDER 1
+static DEFINE_PER_CPU(unsigned char *, zcache_workmem);
+static DEFINE_PER_CPU(unsigned char *, zcache_dstmem);
+
+static int zcache_compress(struct page *from, void **out_va, size_t *out_len)
+{
+ int ret = 0;
+ unsigned char *dmem = __get_cpu_var(zcache_dstmem);
+ unsigned char *wmem = __get_cpu_var(zcache_workmem);
+ char *from_va;
+
+ BUG_ON(!irqs_disabled());
+ if (unlikely(dmem == NULL || wmem == NULL))
+ goto out; /* no buffer, so can't compress */
+ from_va = kmap_atomic(from, KM_USER0);
+ mb();
+ ret = lzo1x_1_compress(from_va, PAGE_SIZE, dmem, out_len, wmem);
+ BUG_ON(ret != LZO_E_OK);
+ *out_va = dmem;
+ kunmap_atomic(from_va, KM_USER0);
+ ret = 1;
+out:
+ return ret;
+}
+
+
+static int zcache_cpu_notifier(struct notifier_block *nb,
+ unsigned long action, void *pcpu)
+{
+ int cpu = (long)pcpu;
+ struct zcache_preload *kp;
+
+ switch (action) {
+ case CPU_UP_PREPARE:
+ per_cpu(zcache_dstmem, cpu) = (void *)__get_free_pages(
+ GFP_KERNEL | __GFP_REPEAT,
+ LZO_DSTMEM_PAGE_ORDER),
+ per_cpu(zcache_workmem, cpu) =
+ kzalloc(LZO1X_MEM_COMPRESS,
+ GFP_KERNEL | __GFP_REPEAT);
+ break;
+ case CPU_DEAD:
+ case CPU_UP_CANCELED:
+ free_pages((unsigned long)per_cpu(zcache_dstmem, cpu),
+ LZO_DSTMEM_PAGE_ORDER);
+ per_cpu(zcache_dstmem, cpu) = NULL;
+ kfree(per_cpu(zcache_workmem, cpu));
+ per_cpu(zcache_workmem, cpu) = NULL;
+ kp = &per_cpu(zcache_preloads, cpu);
+ while (kp->nr) {
+ kmem_cache_free(zcache_objnode_cache,
+ kp->objnodes[kp->nr - 1]);
+ kp->objnodes[kp->nr - 1] = NULL;
+ kp->nr--;
+ }
+ kmem_cache_free(zcache_obj_cache, kp->obj);
+ free_page((unsigned long)kp->page);
+ break;
+ default:
+ break;
+ }
+ return NOTIFY_OK;
+}
+
+static struct notifier_block zcache_cpu_notifier_block = {
+ .notifier_call = zcache_cpu_notifier
+};
+
+#ifdef CONFIG_SYSFS
+#define ZCACHE_SYSFS_RO(_name) \
+ static ssize_t zcache_##_name##_show(struct kobject *kobj, \
+ struct kobj_attribute *attr, char *buf) \
+ { \
+ return sprintf(buf, "%lu\n", zcache_##_name); \
+ } \
+ static struct kobj_attribute zcache_##_name##_attr = { \
+ .attr = { .name = __stringify(_name), .mode = 0444 }, \
+ .show = zcache_##_name##_show, \
+ }
+
+#define ZCACHE_SYSFS_RO_ATOMIC(_name) \
+ static ssize_t zcache_##_name##_show(struct kobject *kobj, \
+ struct kobj_attribute *attr, char *buf) \
+ { \
+ return sprintf(buf, "%d\n", atomic_read(&zcache_##_name)); \
+ } \
+ static struct kobj_attribute zcache_##_name##_attr = { \
+ .attr = { .name = __stringify(_name), .mode = 0444 }, \
+ .show = zcache_##_name##_show, \
+ }
+
+#define ZCACHE_SYSFS_RO_CUSTOM(_name, _func) \
+ static ssize_t zcache_##_name##_show(struct kobject *kobj, \
+ struct kobj_attribute *attr, char *buf) \
+ { \
+ return _func(buf); \
+ } \
+ static struct kobj_attribute zcache_##_name##_attr = { \
+ .attr = { .name = __stringify(_name), .mode = 0444 }, \
+ .show = zcache_##_name##_show, \
+ }
+
+ZCACHE_SYSFS_RO(curr_obj_count_max);
+ZCACHE_SYSFS_RO(curr_objnode_count_max);
+ZCACHE_SYSFS_RO(flush_total);
+ZCACHE_SYSFS_RO(flush_found);
+ZCACHE_SYSFS_RO(flobj_total);
+ZCACHE_SYSFS_RO(flobj_found);
+ZCACHE_SYSFS_RO(failed_eph_puts);
+ZCACHE_SYSFS_RO(failed_pers_puts);
+ZCACHE_SYSFS_RO(zbud_curr_zbytes);
+ZCACHE_SYSFS_RO(zbud_cumul_zpages);
+ZCACHE_SYSFS_RO(zbud_cumul_zbytes);
+ZCACHE_SYSFS_RO(zbud_buddied_count);
+ZCACHE_SYSFS_RO(zbpg_unused_list_count);
+ZCACHE_SYSFS_RO(evicted_raw_pages);
+ZCACHE_SYSFS_RO(evicted_unbuddied_pages);
+ZCACHE_SYSFS_RO(evicted_buddied_pages);
+ZCACHE_SYSFS_RO(failed_get_free_pages);
+ZCACHE_SYSFS_RO(failed_alloc);
+ZCACHE_SYSFS_RO(put_to_flush);
+ZCACHE_SYSFS_RO(aborted_preload);
+ZCACHE_SYSFS_RO(aborted_shrink);
+ZCACHE_SYSFS_RO(compress_poor);
+ZCACHE_SYSFS_RO(mean_compress_poor);
+ZCACHE_SYSFS_RO_ATOMIC(zbud_curr_raw_pages);
+ZCACHE_SYSFS_RO_ATOMIC(zbud_curr_zpages);
+ZCACHE_SYSFS_RO_ATOMIC(curr_obj_count);
+ZCACHE_SYSFS_RO_ATOMIC(curr_objnode_count);
+ZCACHE_SYSFS_RO_CUSTOM(zbud_unbuddied_list_counts,
+ zbud_show_unbuddied_list_counts);
+ZCACHE_SYSFS_RO_CUSTOM(zbud_cumul_chunk_counts,
+ zbud_show_cumul_chunk_counts);
+ZCACHE_SYSFS_RO_CUSTOM(zv_curr_dist_counts,
+ zv_curr_dist_counts_show);
+ZCACHE_SYSFS_RO_CUSTOM(zv_cumul_dist_counts,
+ zv_cumul_dist_counts_show);
+
+static struct attribute *zcache_attrs[] = {
+ &zcache_curr_obj_count_attr.attr,
+ &zcache_curr_obj_count_max_attr.attr,
+ &zcache_curr_objnode_count_attr.attr,
+ &zcache_curr_objnode_count_max_attr.attr,
+ &zcache_flush_total_attr.attr,
+ &zcache_flobj_total_attr.attr,
+ &zcache_flush_found_attr.attr,
+ &zcache_flobj_found_attr.attr,
+ &zcache_failed_eph_puts_attr.attr,
+ &zcache_failed_pers_puts_attr.attr,
+ &zcache_compress_poor_attr.attr,
+ &zcache_mean_compress_poor_attr.attr,
+ &zcache_zbud_curr_raw_pages_attr.attr,
+ &zcache_zbud_curr_zpages_attr.attr,
+ &zcache_zbud_curr_zbytes_attr.attr,
+ &zcache_zbud_cumul_zpages_attr.attr,
+ &zcache_zbud_cumul_zbytes_attr.attr,
+ &zcache_zbud_buddied_count_attr.attr,
+ &zcache_zbpg_unused_list_count_attr.attr,
+ &zcache_evicted_raw_pages_attr.attr,
+ &zcache_evicted_unbuddied_pages_attr.attr,
+ &zcache_evicted_buddied_pages_attr.attr,
+ &zcache_failed_get_free_pages_attr.attr,
+ &zcache_failed_alloc_attr.attr,
+ &zcache_put_to_flush_attr.attr,
+ &zcache_aborted_preload_attr.attr,
+ &zcache_aborted_shrink_attr.attr,
+ &zcache_zbud_unbuddied_list_counts_attr.attr,
+ &zcache_zbud_cumul_chunk_counts_attr.attr,
+ &zcache_zv_curr_dist_counts_attr.attr,
+ &zcache_zv_cumul_dist_counts_attr.attr,
+ &zcache_zv_max_zsize_attr.attr,
+ &zcache_zv_max_mean_zsize_attr.attr,
+ &zcache_zv_page_count_policy_percent_attr.attr,
+ NULL,
+};
+
+static struct attribute_group zcache_attr_group = {
+ .attrs = zcache_attrs,
+ .name = "zcache",
+};
+
+#endif /* CONFIG_SYSFS */
+/*
+ * When zcache is disabled ("frozen"), pools can be created and destroyed,
+ * but all puts (and thus all other operations that require memory allocation)
+ * must fail. If zcache is unfrozen, accepts puts, then frozen again,
+ * data consistency requires all puts while frozen to be converted into
+ * flushes.
+ */
+static bool zcache_freeze;
+
+/*
+ * zcache shrinker interface (only useful for ephemeral pages, so zbud only)
+ */
+static int shrink_zcache_memory(struct shrinker *shrink,
+ struct shrink_control *sc)
+{
+ int ret = -1;
+ int nr = sc->nr_to_scan;
+ gfp_t gfp_mask = sc->gfp_mask;
+
+ if (nr >= 0) {
+ if (!(gfp_mask & __GFP_FS))
+ /* does this case really need to be skipped? */
+ goto out;
+ if (spin_trylock(&zcache_direct_reclaim_lock)) {
+ zbud_evict_pages(nr);
+ spin_unlock(&zcache_direct_reclaim_lock);
+ } else
+ zcache_aborted_shrink++;
+ }
+ ret = (int)atomic_read(&zcache_zbud_curr_raw_pages);
+out:
+ return ret;
+}
+
+static struct shrinker zcache_shrinker = {
+ .shrink = shrink_zcache_memory,
+ .seeks = DEFAULT_SEEKS,
+};
+
+/*
+ * zcache shims between cleancache/frontswap ops and tmem
+ */
+
+static int zcache_put_page(int cli_id, int pool_id, struct tmem_oid *oidp,
+ uint32_t index, struct page *page)
+{
+ struct tmem_pool *pool;
+ int ret = -1;
+
+ BUG_ON(!irqs_disabled());
+ pool = zcache_get_pool_by_id(cli_id, pool_id);
+ if (unlikely(pool == NULL))
+ goto out;
+ if (!zcache_freeze && zcache_do_preload(pool) == 0) {
+ /* preload does preempt_disable on success */
+ ret = tmem_put(pool, oidp, index, page_address(page),
+ PAGE_SIZE, 0, is_ephemeral(pool));
+ if (ret < 0) {
+ if (is_ephemeral(pool))
+ zcache_failed_eph_puts++;
+ else
+ zcache_failed_pers_puts++;
+ }
+ zcache_put_pool(pool);
+ preempt_enable_no_resched();
+ } else {
+ zcache_put_to_flush++;
+ if (atomic_read(&pool->obj_count) > 0)
+ /* the put fails whether the flush succeeds or not */
+ (void)tmem_flush_page(pool, oidp, index);
+ zcache_put_pool(pool);
+ }
+out:
+ return ret;
+}
+
+static int zcache_get_page(int cli_id, int pool_id, struct tmem_oid *oidp,
+ uint32_t index, struct page *page)
+{
+ struct tmem_pool *pool;
+ int ret = -1;
+ unsigned long flags;
+ size_t size = PAGE_SIZE;
+
+ local_irq_save(flags);
+ pool = zcache_get_pool_by_id(cli_id, pool_id);
+ if (likely(pool != NULL)) {
+ if (atomic_read(&pool->obj_count) > 0)
+ ret = tmem_get(pool, oidp, index, page_address(page),
+ &size, 0, is_ephemeral(pool));
+ zcache_put_pool(pool);
+ }
+ local_irq_restore(flags);
+ return ret;
+}
+
+static int zcache_flush_page(int cli_id, int pool_id,
+ struct tmem_oid *oidp, uint32_t index)
+{
+ struct tmem_pool *pool;
+ int ret = -1;
+ unsigned long flags;
+
+ local_irq_save(flags);
+ zcache_flush_total++;
+ pool = zcache_get_pool_by_id(cli_id, pool_id);
+ if (likely(pool != NULL)) {
+ if (atomic_read(&pool->obj_count) > 0)
+ ret = tmem_flush_page(pool, oidp, index);
+ zcache_put_pool(pool);
+ }
+ if (ret >= 0)
+ zcache_flush_found++;
+ local_irq_restore(flags);
+ return ret;
+}
+
+static int zcache_flush_object(int cli_id, int pool_id,
+ struct tmem_oid *oidp)
+{
+ struct tmem_pool *pool;
+ int ret = -1;
+ unsigned long flags;
+
+ local_irq_save(flags);
+ zcache_flobj_total++;
+ pool = zcache_get_pool_by_id(cli_id, pool_id);
+ if (likely(pool != NULL)) {
+ if (atomic_read(&pool->obj_count) > 0)
+ ret = tmem_flush_object(pool, oidp);
+ zcache_put_pool(pool);
+ }
+ if (ret >= 0)
+ zcache_flobj_found++;
+ local_irq_restore(flags);
+ return ret;
+}
+
+static int zcache_destroy_pool(int cli_id, int pool_id)
+{
+ struct tmem_pool *pool = NULL;
+ struct zcache_client *cli = NULL;
+ int ret = -1;
+
+ if (pool_id < 0)
+ goto out;
+ if (cli_id == LOCAL_CLIENT)
+ cli = &zcache_host;
+ else if ((unsigned int)cli_id < MAX_CLIENTS)
+ cli = &zcache_clients[cli_id];
+ if (cli == NULL)
+ goto out;
+ atomic_inc(&cli->refcount);
+ pool = cli->tmem_pools[pool_id];
+ if (pool == NULL)
+ goto out;
+ cli->tmem_pools[pool_id] = NULL;
+ /* wait for pool activity on other cpus to quiesce */
+ while (atomic_read(&pool->refcount) != 0)
+ ;
+ atomic_dec(&cli->refcount);
+ local_bh_disable();
+ ret = tmem_destroy_pool(pool);
+ local_bh_enable();
+ kfree(pool);
+ pr_info("zcache: destroyed pool id=%d, cli_id=%d\n",
+ pool_id, cli_id);
+out:
+ return ret;
+}
+
+static int zcache_new_pool(uint16_t cli_id, uint32_t flags)
+{
+ int poolid = -1;
+ struct tmem_pool *pool;
+ struct zcache_client *cli = NULL;
+
+ if (cli_id == LOCAL_CLIENT)
+ cli = &zcache_host;
+ else if ((unsigned int)cli_id < MAX_CLIENTS)
+ cli = &zcache_clients[cli_id];
+ if (cli == NULL)
+ goto out;
+ atomic_inc(&cli->refcount);
+ pool = kmalloc(sizeof(struct tmem_pool), GFP_KERNEL);
+ if (pool == NULL) {
+ pr_info("zcache: pool creation failed: out of memory\n");
+ goto out;
+ }
+
+ for (poolid = 0; poolid < MAX_POOLS_PER_CLIENT; poolid++)
+ if (cli->tmem_pools[poolid] == NULL)
+ break;
+ if (poolid >= MAX_POOLS_PER_CLIENT) {
+ pr_info("zcache: pool creation failed: max exceeded\n");
+ kfree(pool);
+ poolid = -1;
+ goto out;
+ }
+ atomic_set(&pool->refcount, 0);
+ pool->client = cli;
+ pool->pool_id = poolid;
+ tmem_new_pool(pool, flags);
+ cli->tmem_pools[poolid] = pool;
+ pr_info("zcache: created %s tmem pool, id=%d, client=%d\n",
+ flags & TMEM_POOL_PERSIST ? "persistent" : "ephemeral",
+ poolid, cli_id);
+out:
+ if (cli != NULL)
+ atomic_dec(&cli->refcount);
+ return poolid;
+}
+
+/**********
+ * Two kernel functionalities currently can be layered on top of tmem.
+ * These are "cleancache" which is used as a second-chance cache for clean
+ * page cache pages; and "frontswap" which is used for swap pages
+ * to avoid writes to disk. A generic "shim" is provided here for each
+ * to translate in-kernel semantics to zcache semantics.
+ */
+
+#ifdef CONFIG_CLEANCACHE
+static void zcache_cleancache_put_page(int pool_id,
+ struct cleancache_filekey key,
+ pgoff_t index, struct page *page)
+{
+ u32 ind = (u32) index;
+ struct tmem_oid oid = *(struct tmem_oid *)&key;
+
+ if (likely(ind == index))
+ (void)zcache_put_page(LOCAL_CLIENT, pool_id, &oid, index, page);
+}
+
+static int zcache_cleancache_get_page(int pool_id,
+ struct cleancache_filekey key,
+ pgoff_t index, struct page *page)
+{
+ u32 ind = (u32) index;
+ struct tmem_oid oid = *(struct tmem_oid *)&key;
+ int ret = -1;
+
+ if (likely(ind == index))
+ ret = zcache_get_page(LOCAL_CLIENT, pool_id, &oid, index, page);
+ return ret;
+}
+
+static void zcache_cleancache_flush_page(int pool_id,
+ struct cleancache_filekey key,
+ pgoff_t index)
+{
+ u32 ind = (u32) index;
+ struct tmem_oid oid = *(struct tmem_oid *)&key;
+
+ if (likely(ind == index))
+ (void)zcache_flush_page(LOCAL_CLIENT, pool_id, &oid, ind);
+}
+
+static void zcache_cleancache_flush_inode(int pool_id,
+ struct cleancache_filekey key)
+{
+ struct tmem_oid oid = *(struct tmem_oid *)&key;
+
+ (void)zcache_flush_object(LOCAL_CLIENT, pool_id, &oid);
+}
+
+static void zcache_cleancache_flush_fs(int pool_id)
+{
+ if (pool_id >= 0)
+ (void)zcache_destroy_pool(LOCAL_CLIENT, pool_id);
+}
+
+static int zcache_cleancache_init_fs(size_t pagesize)
+{
+ BUG_ON(sizeof(struct cleancache_filekey) !=
+ sizeof(struct tmem_oid));
+ BUG_ON(pagesize != PAGE_SIZE);
+ return zcache_new_pool(LOCAL_CLIENT, 0);
+}
+
+static int zcache_cleancache_init_shared_fs(char *uuid, size_t pagesize)
+{
+ /* shared pools are unsupported and map to private */
+ BUG_ON(sizeof(struct cleancache_filekey) !=
+ sizeof(struct tmem_oid));
+ BUG_ON(pagesize != PAGE_SIZE);
+ return zcache_new_pool(LOCAL_CLIENT, 0);
+}
+
+static struct cleancache_ops zcache_cleancache_ops = {
+ .put_page = zcache_cleancache_put_page,
+ .get_page = zcache_cleancache_get_page,
+ .flush_page = zcache_cleancache_flush_page,
+ .flush_inode = zcache_cleancache_flush_inode,
+ .flush_fs = zcache_cleancache_flush_fs,
+ .init_shared_fs = zcache_cleancache_init_shared_fs,
+ .init_fs = zcache_cleancache_init_fs
+};
+
+struct cleancache_ops zcache_cleancache_register_ops(void)
+{
+ struct cleancache_ops old_ops =
+ cleancache_register_ops(&zcache_cleancache_ops);
+
+ return old_ops;
+}
+#endif
+
+#ifdef CONFIG_FRONTSWAP
+/* a single tmem poolid is used for all frontswap "types" (swapfiles) */
+static int zcache_frontswap_poolid = -1;
+
+/*
+ * Swizzling increases objects per swaptype, increasing tmem concurrency
+ * for heavy swaploads. Later, larger nr_cpus -> larger SWIZ_BITS
+ */
+#define SWIZ_BITS 4
+#define SWIZ_MASK ((1 << SWIZ_BITS) - 1)
+#define _oswiz(_type, _ind) ((_type << SWIZ_BITS) | (_ind & SWIZ_MASK))
+#define iswiz(_ind) (_ind >> SWIZ_BITS)
+
+static inline struct tmem_oid oswiz(unsigned type, u32 ind)
+{
+ struct tmem_oid oid = { .oid = { 0 } };
+ oid.oid[0] = _oswiz(type, ind);
+ return oid;
+}
+
+static int zcache_frontswap_put_page(unsigned type, pgoff_t offset,
+ struct page *page)
+{
+ u64 ind64 = (u64)offset;
+ u32 ind = (u32)offset;
+ struct tmem_oid oid = oswiz(type, ind);
+ int ret = -1;
+ unsigned long flags;
+
+ BUG_ON(!PageLocked(page));
+ if (likely(ind64 == ind)) {
+ local_irq_save(flags);
+ ret = zcache_put_page(LOCAL_CLIENT, zcache_frontswap_poolid,
+ &oid, iswiz(ind), page);
+ local_irq_restore(flags);
+ }
+ return ret;
+}
+
+/* returns 0 if the page was successfully gotten from frontswap, -1 if
+ * was not present (should never happen!) */
+static int zcache_frontswap_get_page(unsigned type, pgoff_t offset,
+ struct page *page)
+{
+ u64 ind64 = (u64)offset;
+ u32 ind = (u32)offset;
+ struct tmem_oid oid = oswiz(type, ind);
+ int ret = -1;
+
+ BUG_ON(!PageLocked(page));
+ if (likely(ind64 == ind))
+ ret = zcache_get_page(LOCAL_CLIENT, zcache_frontswap_poolid,
+ &oid, iswiz(ind), page);
+ return ret;
+}
+
+/* flush a single page from frontswap */
+static void zcache_frontswap_flush_page(unsigned type, pgoff_t offset)
+{
+ u64 ind64 = (u64)offset;
+ u32 ind = (u32)offset;
+ struct tmem_oid oid = oswiz(type, ind);
+
+ if (likely(ind64 == ind))
+ (void)zcache_flush_page(LOCAL_CLIENT, zcache_frontswap_poolid,
+ &oid, iswiz(ind));
+}
+
+/* flush all pages from the passed swaptype */
+static void zcache_frontswap_flush_area(unsigned type)
+{
+ struct tmem_oid oid;
+ int ind;
+
+ for (ind = SWIZ_MASK; ind >= 0; ind--) {
+ oid = oswiz(type, ind);
+ (void)zcache_flush_object(LOCAL_CLIENT,
+ zcache_frontswap_poolid, &oid);
+ }
+}
+
+static void zcache_frontswap_init(unsigned ignored)
+{
+ /* a single tmem poolid is used for all frontswap "types" (swapfiles) */
+ if (zcache_frontswap_poolid < 0)
+ zcache_frontswap_poolid =
+ zcache_new_pool(LOCAL_CLIENT, TMEM_POOL_PERSIST);
+}
+
+static struct frontswap_ops zcache_frontswap_ops = {
+ .put_page = zcache_frontswap_put_page,
+ .get_page = zcache_frontswap_get_page,
+ .flush_page = zcache_frontswap_flush_page,
+ .flush_area = zcache_frontswap_flush_area,
+ .init = zcache_frontswap_init
+};
+
+struct frontswap_ops zcache_frontswap_register_ops(void)
+{
+ struct frontswap_ops old_ops =
+ frontswap_register_ops(&zcache_frontswap_ops);
+
+ return old_ops;
+}
+#endif
+
+/*
+ * zcache initialization
+ * NOTE FOR NOW zcache MUST BE PROVIDED AS A KERNEL BOOT PARAMETER OR
+ * NOTHING HAPPENS!
+ */
+
+static int zcache_enabled;
+
+static int __init enable_zcache(char *s)
+{
+ zcache_enabled = 1;
+ return 1;
+}
+__setup("zcache", enable_zcache);
+
+/* allow independent dynamic disabling of cleancache and frontswap */
+
+static int use_cleancache = 1;
+
+static int __init no_cleancache(char *s)
+{
+ use_cleancache = 0;
+ return 1;
+}
+
+__setup("nocleancache", no_cleancache);
+
+static int use_frontswap = 1;
+
+static int __init no_frontswap(char *s)
+{
+ use_frontswap = 0;
+ return 1;
+}
+
+__setup("nofrontswap", no_frontswap);
+
+static int __init zcache_init(void)
+{
+ int ret = 0;
+
+#ifdef CONFIG_SYSFS
+ ret = sysfs_create_group(mm_kobj, &zcache_attr_group);
+ if (ret) {
+ pr_err("zcache: can't create sysfs\n");
+ goto out;
+ }
+#endif /* CONFIG_SYSFS */
+#if defined(CONFIG_CLEANCACHE) || defined(CONFIG_FRONTSWAP)
+ if (zcache_enabled) {
+ unsigned int cpu;
+
+ tmem_register_hostops(&zcache_hostops);
+ tmem_register_pamops(&zcache_pamops);
+ ret = register_cpu_notifier(&zcache_cpu_notifier_block);
+ if (ret) {
+ pr_err("zcache: can't register cpu notifier\n");
+ goto out;
+ }
+ for_each_online_cpu(cpu) {
+ void *pcpu = (void *)(long)cpu;
+ zcache_cpu_notifier(&zcache_cpu_notifier_block,
+ CPU_UP_PREPARE, pcpu);
+ }
+ }
+ zcache_objnode_cache = kmem_cache_create("zcache_objnode",
+ sizeof(struct tmem_objnode), 0, 0, NULL);
+ zcache_obj_cache = kmem_cache_create("zcache_obj",
+ sizeof(struct tmem_obj), 0, 0, NULL);
+ ret = zcache_new_client(LOCAL_CLIENT);
+ if (ret) {
+ pr_err("zcache: can't create client\n");
+ goto out;
+ }
+#endif
+#ifdef CONFIG_CLEANCACHE
+ if (zcache_enabled && use_cleancache) {
+ struct cleancache_ops old_ops;
+
+ zbud_init();
+ register_shrinker(&zcache_shrinker);
+ old_ops = zcache_cleancache_register_ops();
+ pr_info("zcache: cleancache enabled using kernel "
+ "transcendent memory and compression buddies\n");
+ if (old_ops.init_fs != NULL)
+ pr_warning("zcache: cleancache_ops overridden");
+ }
+#endif
+#ifdef CONFIG_FRONTSWAP
+ if (zcache_enabled && use_frontswap) {
+ struct frontswap_ops old_ops;
+
+ old_ops = zcache_frontswap_register_ops();
+ pr_info("zcache: frontswap enabled using kernel "
+ "transcendent memory and xvmalloc\n");
+ if (old_ops.init != NULL)
+ pr_warning("ktmem: frontswap_ops overridden");
+ }
+#endif
+out:
+ return ret;
+}
+
+module_init(zcache_init)
+++ /dev/null
-/*
- * zcache.c
- *
- * Copyright (c) 2010,2011, Dan Magenheimer, Oracle Corp.
- * Copyright (c) 2010,2011, Nitin Gupta
- *
- * Zcache provides an in-kernel "host implementation" for transcendent memory
- * and, thus indirectly, for cleancache and frontswap. Zcache includes two
- * page-accessible memory [1] interfaces, both utilizing lzo1x compression:
- * 1) "compression buddies" ("zbud") is used for ephemeral pages
- * 2) xvmalloc is used for persistent pages.
- * Xvmalloc (based on the TLSF allocator) has very low fragmentation
- * so maximizes space efficiency, while zbud allows pairs (and potentially,
- * in the future, more than a pair of) compressed pages to be closely linked
- * so that reclaiming can be done via the kernel's physical-page-oriented
- * "shrinker" interface.
- *
- * [1] For a definition of page-accessible memory (aka PAM), see:
- * http://marc.info/?l=linux-mm&m=127811271605009
- */
-
-#include <linux/cpu.h>
-#include <linux/highmem.h>
-#include <linux/list.h>
-#include <linux/lzo.h>
-#include <linux/slab.h>
-#include <linux/spinlock.h>
-#include <linux/types.h>
-#include <linux/atomic.h>
-#include "tmem.h"
-
-#include "../zram/xvmalloc.h" /* if built in drivers/staging */
-
-#if (!defined(CONFIG_CLEANCACHE) && !defined(CONFIG_FRONTSWAP))
-#error "zcache is useless without CONFIG_CLEANCACHE or CONFIG_FRONTSWAP"
-#endif
-#ifdef CONFIG_CLEANCACHE
-#include <linux/cleancache.h>
-#endif
-#ifdef CONFIG_FRONTSWAP
-#include <linux/frontswap.h>
-#endif
-
-#if 0
-/* this is more aggressive but may cause other problems? */
-#define ZCACHE_GFP_MASK (GFP_ATOMIC | __GFP_NORETRY | __GFP_NOWARN)
-#else
-#define ZCACHE_GFP_MASK \
- (__GFP_FS | __GFP_NORETRY | __GFP_NOWARN | __GFP_NOMEMALLOC)
-#endif
-
-#define MAX_POOLS_PER_CLIENT 16
-
-#define MAX_CLIENTS 16
-#define LOCAL_CLIENT ((uint16_t)-1)
-struct zcache_client {
- struct tmem_pool *tmem_pools[MAX_POOLS_PER_CLIENT];
- struct xv_pool *xvpool;
- bool allocated;
- atomic_t refcount;
-};
-
-static struct zcache_client zcache_host;
-static struct zcache_client zcache_clients[MAX_CLIENTS];
-
-static inline uint16_t get_client_id_from_client(struct zcache_client *cli)
-{
- BUG_ON(cli == NULL);
- if (cli == &zcache_host)
- return LOCAL_CLIENT;
- return cli - &zcache_clients[0];
-}
-
-static inline bool is_local_client(struct zcache_client *cli)
-{
- return cli == &zcache_host;
-}
-
-/**********
- * Compression buddies ("zbud") provides for packing two (or, possibly
- * in the future, more) compressed ephemeral pages into a single "raw"
- * (physical) page and tracking them with data structures so that
- * the raw pages can be easily reclaimed.
- *
- * A zbud page ("zbpg") is an aligned page containing a list_head,
- * a lock, and two "zbud headers". The remainder of the physical
- * page is divided up into aligned 64-byte "chunks" which contain
- * the compressed data for zero, one, or two zbuds. Each zbpg
- * resides on: (1) an "unused list" if it has no zbuds; (2) a
- * "buddied" list if it is fully populated with two zbuds; or
- * (3) one of PAGE_SIZE/64 "unbuddied" lists indexed by how many chunks
- * the one unbuddied zbud uses. The data inside a zbpg cannot be
- * read or written unless the zbpg's lock is held.
- */
-
-#define ZBH_SENTINEL 0x43214321
-#define ZBPG_SENTINEL 0xdeadbeef
-
-#define ZBUD_MAX_BUDS 2
-
-struct zbud_hdr {
- uint16_t client_id;
- uint16_t pool_id;
- struct tmem_oid oid;
- uint32_t index;
- uint16_t size; /* compressed size in bytes, zero means unused */
- DECL_SENTINEL
-};
-
-struct zbud_page {
- struct list_head bud_list;
- spinlock_t lock;
- struct zbud_hdr buddy[ZBUD_MAX_BUDS];
- DECL_SENTINEL
- /* followed by NUM_CHUNK aligned CHUNK_SIZE-byte chunks */
-};
-
-#define CHUNK_SHIFT 6
-#define CHUNK_SIZE (1 << CHUNK_SHIFT)
-#define CHUNK_MASK (~(CHUNK_SIZE-1))
-#define NCHUNKS (((PAGE_SIZE - sizeof(struct zbud_page)) & \
- CHUNK_MASK) >> CHUNK_SHIFT)
-#define MAX_CHUNK (NCHUNKS-1)
-
-static struct {
- struct list_head list;
- unsigned count;
-} zbud_unbuddied[NCHUNKS];
-/* list N contains pages with N chunks USED and NCHUNKS-N unused */
-/* element 0 is never used but optimizing that isn't worth it */
-static unsigned long zbud_cumul_chunk_counts[NCHUNKS];
-
-struct list_head zbud_buddied_list;
-static unsigned long zcache_zbud_buddied_count;
-
-/* protects the buddied list and all unbuddied lists */
-static DEFINE_SPINLOCK(zbud_budlists_spinlock);
-
-static LIST_HEAD(zbpg_unused_list);
-static unsigned long zcache_zbpg_unused_list_count;
-
-/* protects the unused page list */
-static DEFINE_SPINLOCK(zbpg_unused_list_spinlock);
-
-static atomic_t zcache_zbud_curr_raw_pages;
-static atomic_t zcache_zbud_curr_zpages;
-static unsigned long zcache_zbud_curr_zbytes;
-static unsigned long zcache_zbud_cumul_zpages;
-static unsigned long zcache_zbud_cumul_zbytes;
-static unsigned long zcache_compress_poor;
-static unsigned long zcache_mean_compress_poor;
-
-/* forward references */
-static void *zcache_get_free_page(void);
-static void zcache_free_page(void *p);
-
-/*
- * zbud helper functions
- */
-
-static inline unsigned zbud_max_buddy_size(void)
-{
- return MAX_CHUNK << CHUNK_SHIFT;
-}
-
-static inline unsigned zbud_size_to_chunks(unsigned size)
-{
- BUG_ON(size == 0 || size > zbud_max_buddy_size());
- return (size + CHUNK_SIZE - 1) >> CHUNK_SHIFT;
-}
-
-static inline int zbud_budnum(struct zbud_hdr *zh)
-{
- unsigned offset = (unsigned long)zh & (PAGE_SIZE - 1);
- struct zbud_page *zbpg = NULL;
- unsigned budnum = -1U;
- int i;
-
- for (i = 0; i < ZBUD_MAX_BUDS; i++)
- if (offset == offsetof(typeof(*zbpg), buddy[i])) {
- budnum = i;
- break;
- }
- BUG_ON(budnum == -1U);
- return budnum;
-}
-
-static char *zbud_data(struct zbud_hdr *zh, unsigned size)
-{
- struct zbud_page *zbpg;
- char *p;
- unsigned budnum;
-
- ASSERT_SENTINEL(zh, ZBH);
- budnum = zbud_budnum(zh);
- BUG_ON(size == 0 || size > zbud_max_buddy_size());
- zbpg = container_of(zh, struct zbud_page, buddy[budnum]);
- ASSERT_SPINLOCK(&zbpg->lock);
- p = (char *)zbpg;
- if (budnum == 0)
- p += ((sizeof(struct zbud_page) + CHUNK_SIZE - 1) &
- CHUNK_MASK);
- else if (budnum == 1)
- p += PAGE_SIZE - ((size + CHUNK_SIZE - 1) & CHUNK_MASK);
- return p;
-}
-
-/*
- * zbud raw page management
- */
-
-static struct zbud_page *zbud_alloc_raw_page(void)
-{
- struct zbud_page *zbpg = NULL;
- struct zbud_hdr *zh0, *zh1;
- bool recycled = 0;
-
- /* if any pages on the zbpg list, use one */
- spin_lock(&zbpg_unused_list_spinlock);
- if (!list_empty(&zbpg_unused_list)) {
- zbpg = list_first_entry(&zbpg_unused_list,
- struct zbud_page, bud_list);
- list_del_init(&zbpg->bud_list);
- zcache_zbpg_unused_list_count--;
- recycled = 1;
- }
- spin_unlock(&zbpg_unused_list_spinlock);
- if (zbpg == NULL)
- /* none on zbpg list, try to get a kernel page */
- zbpg = zcache_get_free_page();
- if (likely(zbpg != NULL)) {
- INIT_LIST_HEAD(&zbpg->bud_list);
- zh0 = &zbpg->buddy[0]; zh1 = &zbpg->buddy[1];
- spin_lock_init(&zbpg->lock);
- if (recycled) {
- ASSERT_INVERTED_SENTINEL(zbpg, ZBPG);
- SET_SENTINEL(zbpg, ZBPG);
- BUG_ON(zh0->size != 0 || tmem_oid_valid(&zh0->oid));
- BUG_ON(zh1->size != 0 || tmem_oid_valid(&zh1->oid));
- } else {
- atomic_inc(&zcache_zbud_curr_raw_pages);
- INIT_LIST_HEAD(&zbpg->bud_list);
- SET_SENTINEL(zbpg, ZBPG);
- zh0->size = 0; zh1->size = 0;
- tmem_oid_set_invalid(&zh0->oid);
- tmem_oid_set_invalid(&zh1->oid);
- }
- }
- return zbpg;
-}
-
-static void zbud_free_raw_page(struct zbud_page *zbpg)
-{
- struct zbud_hdr *zh0 = &zbpg->buddy[0], *zh1 = &zbpg->buddy[1];
-
- ASSERT_SENTINEL(zbpg, ZBPG);
- BUG_ON(!list_empty(&zbpg->bud_list));
- ASSERT_SPINLOCK(&zbpg->lock);
- BUG_ON(zh0->size != 0 || tmem_oid_valid(&zh0->oid));
- BUG_ON(zh1->size != 0 || tmem_oid_valid(&zh1->oid));
- INVERT_SENTINEL(zbpg, ZBPG);
- spin_unlock(&zbpg->lock);
- spin_lock(&zbpg_unused_list_spinlock);
- list_add(&zbpg->bud_list, &zbpg_unused_list);
- zcache_zbpg_unused_list_count++;
- spin_unlock(&zbpg_unused_list_spinlock);
-}
-
-/*
- * core zbud handling routines
- */
-
-static unsigned zbud_free(struct zbud_hdr *zh)
-{
- unsigned size;
-
- ASSERT_SENTINEL(zh, ZBH);
- BUG_ON(!tmem_oid_valid(&zh->oid));
- size = zh->size;
- BUG_ON(zh->size == 0 || zh->size > zbud_max_buddy_size());
- zh->size = 0;
- tmem_oid_set_invalid(&zh->oid);
- INVERT_SENTINEL(zh, ZBH);
- zcache_zbud_curr_zbytes -= size;
- atomic_dec(&zcache_zbud_curr_zpages);
- return size;
-}
-
-static void zbud_free_and_delist(struct zbud_hdr *zh)
-{
- unsigned chunks;
- struct zbud_hdr *zh_other;
- unsigned budnum = zbud_budnum(zh), size;
- struct zbud_page *zbpg =
- container_of(zh, struct zbud_page, buddy[budnum]);
-
- spin_lock(&zbpg->lock);
- if (list_empty(&zbpg->bud_list)) {
- /* ignore zombie page... see zbud_evict_pages() */
- spin_unlock(&zbpg->lock);
- return;
- }
- size = zbud_free(zh);
- ASSERT_SPINLOCK(&zbpg->lock);
- zh_other = &zbpg->buddy[(budnum == 0) ? 1 : 0];
- if (zh_other->size == 0) { /* was unbuddied: unlist and free */
- chunks = zbud_size_to_chunks(size) ;
- spin_lock(&zbud_budlists_spinlock);
- BUG_ON(list_empty(&zbud_unbuddied[chunks].list));
- list_del_init(&zbpg->bud_list);
- zbud_unbuddied[chunks].count--;
- spin_unlock(&zbud_budlists_spinlock);
- zbud_free_raw_page(zbpg);
- } else { /* was buddied: move remaining buddy to unbuddied list */
- chunks = zbud_size_to_chunks(zh_other->size) ;
- spin_lock(&zbud_budlists_spinlock);
- list_del_init(&zbpg->bud_list);
- zcache_zbud_buddied_count--;
- list_add_tail(&zbpg->bud_list, &zbud_unbuddied[chunks].list);
- zbud_unbuddied[chunks].count++;
- spin_unlock(&zbud_budlists_spinlock);
- spin_unlock(&zbpg->lock);
- }
-}
-
-static struct zbud_hdr *zbud_create(uint16_t client_id, uint16_t pool_id,
- struct tmem_oid *oid,
- uint32_t index, struct page *page,
- void *cdata, unsigned size)
-{
- struct zbud_hdr *zh0, *zh1, *zh = NULL;
- struct zbud_page *zbpg = NULL, *ztmp;
- unsigned nchunks;
- char *to;
- int i, found_good_buddy = 0;
-
- nchunks = zbud_size_to_chunks(size) ;
- for (i = MAX_CHUNK - nchunks + 1; i > 0; i--) {
- spin_lock(&zbud_budlists_spinlock);
- if (!list_empty(&zbud_unbuddied[i].list)) {
- list_for_each_entry_safe(zbpg, ztmp,
- &zbud_unbuddied[i].list, bud_list) {
- if (spin_trylock(&zbpg->lock)) {
- found_good_buddy = i;
- goto found_unbuddied;
- }
- }
- }
- spin_unlock(&zbud_budlists_spinlock);
- }
- /* didn't find a good buddy, try allocating a new page */
- zbpg = zbud_alloc_raw_page();
- if (unlikely(zbpg == NULL))
- goto out;
- /* ok, have a page, now compress the data before taking locks */
- spin_lock(&zbpg->lock);
- spin_lock(&zbud_budlists_spinlock);
- list_add_tail(&zbpg->bud_list, &zbud_unbuddied[nchunks].list);
- zbud_unbuddied[nchunks].count++;
- zh = &zbpg->buddy[0];
- goto init_zh;
-
-found_unbuddied:
- ASSERT_SPINLOCK(&zbpg->lock);
- zh0 = &zbpg->buddy[0]; zh1 = &zbpg->buddy[1];
- BUG_ON(!((zh0->size == 0) ^ (zh1->size == 0)));
- if (zh0->size != 0) { /* buddy0 in use, buddy1 is vacant */
- ASSERT_SENTINEL(zh0, ZBH);
- zh = zh1;
- } else if (zh1->size != 0) { /* buddy1 in use, buddy0 is vacant */
- ASSERT_SENTINEL(zh1, ZBH);
- zh = zh0;
- } else
- BUG();
- list_del_init(&zbpg->bud_list);
- zbud_unbuddied[found_good_buddy].count--;
- list_add_tail(&zbpg->bud_list, &zbud_buddied_list);
- zcache_zbud_buddied_count++;
-
-init_zh:
- SET_SENTINEL(zh, ZBH);
- zh->size = size;
- zh->index = index;
- zh->oid = *oid;
- zh->pool_id = pool_id;
- zh->client_id = client_id;
- /* can wait to copy the data until the list locks are dropped */
- spin_unlock(&zbud_budlists_spinlock);
-
- to = zbud_data(zh, size);
- memcpy(to, cdata, size);
- spin_unlock(&zbpg->lock);
- zbud_cumul_chunk_counts[nchunks]++;
- atomic_inc(&zcache_zbud_curr_zpages);
- zcache_zbud_cumul_zpages++;
- zcache_zbud_curr_zbytes += size;
- zcache_zbud_cumul_zbytes += size;
-out:
- return zh;
-}
-
-static int zbud_decompress(struct page *page, struct zbud_hdr *zh)
-{
- struct zbud_page *zbpg;
- unsigned budnum = zbud_budnum(zh);
- size_t out_len = PAGE_SIZE;
- char *to_va, *from_va;
- unsigned size;
- int ret = 0;
-
- zbpg = container_of(zh, struct zbud_page, buddy[budnum]);
- spin_lock(&zbpg->lock);
- if (list_empty(&zbpg->bud_list)) {
- /* ignore zombie page... see zbud_evict_pages() */
- ret = -EINVAL;
- goto out;
- }
- ASSERT_SENTINEL(zh, ZBH);
- BUG_ON(zh->size == 0 || zh->size > zbud_max_buddy_size());
- to_va = kmap_atomic(page, KM_USER0);
- size = zh->size;
- from_va = zbud_data(zh, size);
- ret = lzo1x_decompress_safe(from_va, size, to_va, &out_len);
- BUG_ON(ret != LZO_E_OK);
- BUG_ON(out_len != PAGE_SIZE);
- kunmap_atomic(to_va, KM_USER0);
-out:
- spin_unlock(&zbpg->lock);
- return ret;
-}
-
-/*
- * The following routines handle shrinking of ephemeral pages by evicting
- * pages "least valuable" first.
- */
-
-static unsigned long zcache_evicted_raw_pages;
-static unsigned long zcache_evicted_buddied_pages;
-static unsigned long zcache_evicted_unbuddied_pages;
-
-static struct tmem_pool *zcache_get_pool_by_id(uint16_t cli_id,
- uint16_t poolid);
-static void zcache_put_pool(struct tmem_pool *pool);
-
-/*
- * Flush and free all zbuds in a zbpg, then free the pageframe
- */
-static void zbud_evict_zbpg(struct zbud_page *zbpg)
-{
- struct zbud_hdr *zh;
- int i, j;
- uint32_t pool_id[ZBUD_MAX_BUDS], client_id[ZBUD_MAX_BUDS];
- uint32_t index[ZBUD_MAX_BUDS];
- struct tmem_oid oid[ZBUD_MAX_BUDS];
- struct tmem_pool *pool;
-
- ASSERT_SPINLOCK(&zbpg->lock);
- BUG_ON(!list_empty(&zbpg->bud_list));
- for (i = 0, j = 0; i < ZBUD_MAX_BUDS; i++) {
- zh = &zbpg->buddy[i];
- if (zh->size) {
- client_id[j] = zh->client_id;
- pool_id[j] = zh->pool_id;
- oid[j] = zh->oid;
- index[j] = zh->index;
- j++;
- zbud_free(zh);
- }
- }
- spin_unlock(&zbpg->lock);
- for (i = 0; i < j; i++) {
- pool = zcache_get_pool_by_id(client_id[i], pool_id[i]);
- if (pool != NULL) {
- tmem_flush_page(pool, &oid[i], index[i]);
- zcache_put_pool(pool);
- }
- }
- ASSERT_SENTINEL(zbpg, ZBPG);
- spin_lock(&zbpg->lock);
- zbud_free_raw_page(zbpg);
-}
-
-/*
- * Free nr pages. This code is funky because we want to hold the locks
- * protecting various lists for as short a time as possible, and in some
- * circumstances the list may change asynchronously when the list lock is
- * not held. In some cases we also trylock not only to avoid waiting on a
- * page in use by another cpu, but also to avoid potential deadlock due to
- * lock inversion.
- */
-static void zbud_evict_pages(int nr)
-{
- struct zbud_page *zbpg;
- int i;
-
- /* first try freeing any pages on unused list */
-retry_unused_list:
- spin_lock_bh(&zbpg_unused_list_spinlock);
- if (!list_empty(&zbpg_unused_list)) {
- /* can't walk list here, since it may change when unlocked */
- zbpg = list_first_entry(&zbpg_unused_list,
- struct zbud_page, bud_list);
- list_del_init(&zbpg->bud_list);
- zcache_zbpg_unused_list_count--;
- atomic_dec(&zcache_zbud_curr_raw_pages);
- spin_unlock_bh(&zbpg_unused_list_spinlock);
- zcache_free_page(zbpg);
- zcache_evicted_raw_pages++;
- if (--nr <= 0)
- goto out;
- goto retry_unused_list;
- }
- spin_unlock_bh(&zbpg_unused_list_spinlock);
-
- /* now try freeing unbuddied pages, starting with least space avail */
- for (i = 0; i < MAX_CHUNK; i++) {
-retry_unbud_list_i:
- spin_lock_bh(&zbud_budlists_spinlock);
- if (list_empty(&zbud_unbuddied[i].list)) {
- spin_unlock_bh(&zbud_budlists_spinlock);
- continue;
- }
- list_for_each_entry(zbpg, &zbud_unbuddied[i].list, bud_list) {
- if (unlikely(!spin_trylock(&zbpg->lock)))
- continue;
- list_del_init(&zbpg->bud_list);
- zbud_unbuddied[i].count--;
- spin_unlock(&zbud_budlists_spinlock);
- zcache_evicted_unbuddied_pages++;
- /* want budlists unlocked when doing zbpg eviction */
- zbud_evict_zbpg(zbpg);
- local_bh_enable();
- if (--nr <= 0)
- goto out;
- goto retry_unbud_list_i;
- }
- spin_unlock_bh(&zbud_budlists_spinlock);
- }
-
- /* as a last resort, free buddied pages */
-retry_bud_list:
- spin_lock_bh(&zbud_budlists_spinlock);
- if (list_empty(&zbud_buddied_list)) {
- spin_unlock_bh(&zbud_budlists_spinlock);
- goto out;
- }
- list_for_each_entry(zbpg, &zbud_buddied_list, bud_list) {
- if (unlikely(!spin_trylock(&zbpg->lock)))
- continue;
- list_del_init(&zbpg->bud_list);
- zcache_zbud_buddied_count--;
- spin_unlock(&zbud_budlists_spinlock);
- zcache_evicted_buddied_pages++;
- /* want budlists unlocked when doing zbpg eviction */
- zbud_evict_zbpg(zbpg);
- local_bh_enable();
- if (--nr <= 0)
- goto out;
- goto retry_bud_list;
- }
- spin_unlock_bh(&zbud_budlists_spinlock);
-out:
- return;
-}
-
-static void zbud_init(void)
-{
- int i;
-
- INIT_LIST_HEAD(&zbud_buddied_list);
- zcache_zbud_buddied_count = 0;
- for (i = 0; i < NCHUNKS; i++) {
- INIT_LIST_HEAD(&zbud_unbuddied[i].list);
- zbud_unbuddied[i].count = 0;
- }
-}
-
-#ifdef CONFIG_SYSFS
-/*
- * These sysfs routines show a nice distribution of how many zbpg's are
- * currently (and have ever been placed) in each unbuddied list. It's fun
- * to watch but can probably go away before final merge.
- */
-static int zbud_show_unbuddied_list_counts(char *buf)
-{
- int i;
- char *p = buf;
-
- for (i = 0; i < NCHUNKS; i++)
- p += sprintf(p, "%u ", zbud_unbuddied[i].count);
- return p - buf;
-}
-
-static int zbud_show_cumul_chunk_counts(char *buf)
-{
- unsigned long i, chunks = 0, total_chunks = 0, sum_total_chunks = 0;
- unsigned long total_chunks_lte_21 = 0, total_chunks_lte_32 = 0;
- unsigned long total_chunks_lte_42 = 0;
- char *p = buf;
-
- for (i = 0; i < NCHUNKS; i++) {
- p += sprintf(p, "%lu ", zbud_cumul_chunk_counts[i]);
- chunks += zbud_cumul_chunk_counts[i];
- total_chunks += zbud_cumul_chunk_counts[i];
- sum_total_chunks += i * zbud_cumul_chunk_counts[i];
- if (i == 21)
- total_chunks_lte_21 = total_chunks;
- if (i == 32)
- total_chunks_lte_32 = total_chunks;
- if (i == 42)
- total_chunks_lte_42 = total_chunks;
- }
- p += sprintf(p, "<=21:%lu <=32:%lu <=42:%lu, mean:%lu\n",
- total_chunks_lte_21, total_chunks_lte_32, total_chunks_lte_42,
- chunks == 0 ? 0 : sum_total_chunks / chunks);
- return p - buf;
-}
-#endif
-
-/**********
- * This "zv" PAM implementation combines the TLSF-based xvMalloc
- * with lzo1x compression to maximize the amount of data that can
- * be packed into a physical page.
- *
- * Zv represents a PAM page with the index and object (plus a "size" value
- * necessary for decompression) immediately preceding the compressed data.
- */
-
-#define ZVH_SENTINEL 0x43214321
-
-struct zv_hdr {
- uint32_t pool_id;
- struct tmem_oid oid;
- uint32_t index;
- DECL_SENTINEL
-};
-
-/* rudimentary policy limits */
-/* total number of persistent pages may not exceed this percentage */
-static unsigned int zv_page_count_policy_percent = 75;
-/*
- * byte count defining poor compression; pages with greater zsize will be
- * rejected
- */
-static unsigned int zv_max_zsize = (PAGE_SIZE / 8) * 7;
-/*
- * byte count defining poor *mean* compression; pages with greater zsize
- * will be rejected until sufficient better-compressed pages are accepted
- * driving the man below this threshold
- */
-static unsigned int zv_max_mean_zsize = (PAGE_SIZE / 8) * 5;
-
-static unsigned long zv_curr_dist_counts[NCHUNKS];
-static unsigned long zv_cumul_dist_counts[NCHUNKS];
-
-static struct zv_hdr *zv_create(struct xv_pool *xvpool, uint32_t pool_id,
- struct tmem_oid *oid, uint32_t index,
- void *cdata, unsigned clen)
-{
- struct page *page;
- struct zv_hdr *zv = NULL;
- uint32_t offset;
- int alloc_size = clen + sizeof(struct zv_hdr);
- int chunks = (alloc_size + (CHUNK_SIZE - 1)) >> CHUNK_SHIFT;
- int ret;
-
- BUG_ON(!irqs_disabled());
- BUG_ON(chunks >= NCHUNKS);
- ret = xv_malloc(xvpool, alloc_size,
- &page, &offset, ZCACHE_GFP_MASK);
- if (unlikely(ret))
- goto out;
- zv_curr_dist_counts[chunks]++;
- zv_cumul_dist_counts[chunks]++;
- zv = kmap_atomic(page, KM_USER0) + offset;
- zv->index = index;
- zv->oid = *oid;
- zv->pool_id = pool_id;
- SET_SENTINEL(zv, ZVH);
- memcpy((char *)zv + sizeof(struct zv_hdr), cdata, clen);
- kunmap_atomic(zv, KM_USER0);
-out:
- return zv;
-}
-
-static void zv_free(struct xv_pool *xvpool, struct zv_hdr *zv)
-{
- unsigned long flags;
- struct page *page;
- uint32_t offset;
- uint16_t size = xv_get_object_size(zv);
- int chunks = (size + (CHUNK_SIZE - 1)) >> CHUNK_SHIFT;
-
- ASSERT_SENTINEL(zv, ZVH);
- BUG_ON(chunks >= NCHUNKS);
- zv_curr_dist_counts[chunks]--;
- size -= sizeof(*zv);
- BUG_ON(size == 0);
- INVERT_SENTINEL(zv, ZVH);
- page = virt_to_page(zv);
- offset = (unsigned long)zv & ~PAGE_MASK;
- local_irq_save(flags);
- xv_free(xvpool, page, offset);
- local_irq_restore(flags);
-}
-
-static void zv_decompress(struct page *page, struct zv_hdr *zv)
-{
- size_t clen = PAGE_SIZE;
- char *to_va;
- unsigned size;
- int ret;
-
- ASSERT_SENTINEL(zv, ZVH);
- size = xv_get_object_size(zv) - sizeof(*zv);
- BUG_ON(size == 0);
- to_va = kmap_atomic(page, KM_USER0);
- ret = lzo1x_decompress_safe((char *)zv + sizeof(*zv),
- size, to_va, &clen);
- kunmap_atomic(to_va, KM_USER0);
- BUG_ON(ret != LZO_E_OK);
- BUG_ON(clen != PAGE_SIZE);
-}
-
-#ifdef CONFIG_SYSFS
-/*
- * show a distribution of compression stats for zv pages.
- */
-
-static int zv_curr_dist_counts_show(char *buf)
-{
- unsigned long i, n, chunks = 0, sum_total_chunks = 0;
- char *p = buf;
-
- for (i = 0; i < NCHUNKS; i++) {
- n = zv_curr_dist_counts[i];
- p += sprintf(p, "%lu ", n);
- chunks += n;
- sum_total_chunks += i * n;
- }
- p += sprintf(p, "mean:%lu\n",
- chunks == 0 ? 0 : sum_total_chunks / chunks);
- return p - buf;
-}
-
-static int zv_cumul_dist_counts_show(char *buf)
-{
- unsigned long i, n, chunks = 0, sum_total_chunks = 0;
- char *p = buf;
-
- for (i = 0; i < NCHUNKS; i++) {
- n = zv_cumul_dist_counts[i];
- p += sprintf(p, "%lu ", n);
- chunks += n;
- sum_total_chunks += i * n;
- }
- p += sprintf(p, "mean:%lu\n",
- chunks == 0 ? 0 : sum_total_chunks / chunks);
- return p - buf;
-}
-
-/*
- * setting zv_max_zsize via sysfs causes all persistent (e.g. swap)
- * pages that don't compress to less than this value (including metadata
- * overhead) to be rejected. We don't allow the value to get too close
- * to PAGE_SIZE.
- */
-static ssize_t zv_max_zsize_show(struct kobject *kobj,
- struct kobj_attribute *attr,
- char *buf)
-{
- return sprintf(buf, "%u\n", zv_max_zsize);
-}
-
-static ssize_t zv_max_zsize_store(struct kobject *kobj,
- struct kobj_attribute *attr,
- const char *buf, size_t count)
-{
- unsigned long val;
- int err;
-
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- err = strict_strtoul(buf, 10, &val);
- if (err || (val == 0) || (val > (PAGE_SIZE / 8) * 7))
- return -EINVAL;
- zv_max_zsize = val;
- return count;
-}
-
-/*
- * setting zv_max_mean_zsize via sysfs causes all persistent (e.g. swap)
- * pages that don't compress to less than this value (including metadata
- * overhead) to be rejected UNLESS the mean compression is also smaller
- * than this value. In other words, we are load-balancing-by-zsize the
- * accepted pages. Again, we don't allow the value to get too close
- * to PAGE_SIZE.
- */
-static ssize_t zv_max_mean_zsize_show(struct kobject *kobj,
- struct kobj_attribute *attr,
- char *buf)
-{
- return sprintf(buf, "%u\n", zv_max_mean_zsize);
-}
-
-static ssize_t zv_max_mean_zsize_store(struct kobject *kobj,
- struct kobj_attribute *attr,
- const char *buf, size_t count)
-{
- unsigned long val;
- int err;
-
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- err = strict_strtoul(buf, 10, &val);
- if (err || (val == 0) || (val > (PAGE_SIZE / 8) * 7))
- return -EINVAL;
- zv_max_mean_zsize = val;
- return count;
-}
-
-/*
- * setting zv_page_count_policy_percent via sysfs sets an upper bound of
- * persistent (e.g. swap) pages that will be retained according to:
- * (zv_page_count_policy_percent * totalram_pages) / 100)
- * when that limit is reached, further puts will be rejected (until
- * some pages have been flushed). Note that, due to compression,
- * this number may exceed 100; it defaults to 75 and we set an
- * arbitary limit of 150. A poor choice will almost certainly result
- * in OOM's, so this value should only be changed prudently.
- */
-static ssize_t zv_page_count_policy_percent_show(struct kobject *kobj,
- struct kobj_attribute *attr,
- char *buf)
-{
- return sprintf(buf, "%u\n", zv_page_count_policy_percent);
-}
-
-static ssize_t zv_page_count_policy_percent_store(struct kobject *kobj,
- struct kobj_attribute *attr,
- const char *buf, size_t count)
-{
- unsigned long val;
- int err;
-
- if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
-
- err = strict_strtoul(buf, 10, &val);
- if (err || (val == 0) || (val > 150))
- return -EINVAL;
- zv_page_count_policy_percent = val;
- return count;
-}
-
-static struct kobj_attribute zcache_zv_max_zsize_attr = {
- .attr = { .name = "zv_max_zsize", .mode = 0644 },
- .show = zv_max_zsize_show,
- .store = zv_max_zsize_store,
-};
-
-static struct kobj_attribute zcache_zv_max_mean_zsize_attr = {
- .attr = { .name = "zv_max_mean_zsize", .mode = 0644 },
- .show = zv_max_mean_zsize_show,
- .store = zv_max_mean_zsize_store,
-};
-
-static struct kobj_attribute zcache_zv_page_count_policy_percent_attr = {
- .attr = { .name = "zv_page_count_policy_percent",
- .mode = 0644 },
- .show = zv_page_count_policy_percent_show,
- .store = zv_page_count_policy_percent_store,
-};
-#endif
-
-/*
- * zcache core code starts here
- */
-
-/* useful stats not collected by cleancache or frontswap */
-static unsigned long zcache_flush_total;
-static unsigned long zcache_flush_found;
-static unsigned long zcache_flobj_total;
-static unsigned long zcache_flobj_found;
-static unsigned long zcache_failed_eph_puts;
-static unsigned long zcache_failed_pers_puts;
-
-/*
- * Tmem operations assume the poolid implies the invoking client.
- * Zcache only has one client (the kernel itself): LOCAL_CLIENT.
- * RAMster has each client numbered by cluster node, and a KVM version
- * of zcache would have one client per guest and each client might
- * have a poolid==N.
- */
-static struct tmem_pool *zcache_get_pool_by_id(uint16_t cli_id, uint16_t poolid)
-{
- struct tmem_pool *pool = NULL;
- struct zcache_client *cli = NULL;
-
- if (cli_id == LOCAL_CLIENT)
- cli = &zcache_host;
- else {
- if (cli_id >= MAX_CLIENTS)
- goto out;
- cli = &zcache_clients[cli_id];
- if (cli == NULL)
- goto out;
- atomic_inc(&cli->refcount);
- }
- if (poolid < MAX_POOLS_PER_CLIENT) {
- pool = cli->tmem_pools[poolid];
- if (pool != NULL)
- atomic_inc(&pool->refcount);
- }
-out:
- return pool;
-}
-
-static void zcache_put_pool(struct tmem_pool *pool)
-{
- struct zcache_client *cli = NULL;
-
- if (pool == NULL)
- BUG();
- cli = pool->client;
- atomic_dec(&pool->refcount);
- atomic_dec(&cli->refcount);
-}
-
-int zcache_new_client(uint16_t cli_id)
-{
- struct zcache_client *cli = NULL;
- int ret = -1;
-
- if (cli_id == LOCAL_CLIENT)
- cli = &zcache_host;
- else if ((unsigned int)cli_id < MAX_CLIENTS)
- cli = &zcache_clients[cli_id];
- if (cli == NULL)
- goto out;
- if (cli->allocated)
- goto out;
- cli->allocated = 1;
-#ifdef CONFIG_FRONTSWAP
- cli->xvpool = xv_create_pool();
- if (cli->xvpool == NULL)
- goto out;
-#endif
- ret = 0;
-out:
- return ret;
-}
-
-/* counters for debugging */
-static unsigned long zcache_failed_get_free_pages;
-static unsigned long zcache_failed_alloc;
-static unsigned long zcache_put_to_flush;
-static unsigned long zcache_aborted_preload;
-static unsigned long zcache_aborted_shrink;
-
-/*
- * Ensure that memory allocation requests in zcache don't result
- * in direct reclaim requests via the shrinker, which would cause
- * an infinite loop. Maybe a GFP flag would be better?
- */
-static DEFINE_SPINLOCK(zcache_direct_reclaim_lock);
-
-/*
- * for now, used named slabs so can easily track usage; later can
- * either just use kmalloc, or perhaps add a slab-like allocator
- * to more carefully manage total memory utilization
- */
-static struct kmem_cache *zcache_objnode_cache;
-static struct kmem_cache *zcache_obj_cache;
-static atomic_t zcache_curr_obj_count = ATOMIC_INIT(0);
-static unsigned long zcache_curr_obj_count_max;
-static atomic_t zcache_curr_objnode_count = ATOMIC_INIT(0);
-static unsigned long zcache_curr_objnode_count_max;
-
-/*
- * to avoid memory allocation recursion (e.g. due to direct reclaim), we
- * preload all necessary data structures so the hostops callbacks never
- * actually do a malloc
- */
-struct zcache_preload {
- void *page;
- struct tmem_obj *obj;
- int nr;
- struct tmem_objnode *objnodes[OBJNODE_TREE_MAX_PATH];
-};
-static DEFINE_PER_CPU(struct zcache_preload, zcache_preloads) = { 0, };
-
-static int zcache_do_preload(struct tmem_pool *pool)
-{
- struct zcache_preload *kp;
- struct tmem_objnode *objnode;
- struct tmem_obj *obj;
- void *page;
- int ret = -ENOMEM;
-
- if (unlikely(zcache_objnode_cache == NULL))
- goto out;
- if (unlikely(zcache_obj_cache == NULL))
- goto out;
- if (!spin_trylock(&zcache_direct_reclaim_lock)) {
- zcache_aborted_preload++;
- goto out;
- }
- preempt_disable();
- kp = &__get_cpu_var(zcache_preloads);
- while (kp->nr < ARRAY_SIZE(kp->objnodes)) {
- preempt_enable_no_resched();
- objnode = kmem_cache_alloc(zcache_objnode_cache,
- ZCACHE_GFP_MASK);
- if (unlikely(objnode == NULL)) {
- zcache_failed_alloc++;
- goto unlock_out;
- }
- preempt_disable();
- kp = &__get_cpu_var(zcache_preloads);
- if (kp->nr < ARRAY_SIZE(kp->objnodes))
- kp->objnodes[kp->nr++] = objnode;
- else
- kmem_cache_free(zcache_objnode_cache, objnode);
- }
- preempt_enable_no_resched();
- obj = kmem_cache_alloc(zcache_obj_cache, ZCACHE_GFP_MASK);
- if (unlikely(obj == NULL)) {
- zcache_failed_alloc++;
- goto unlock_out;
- }
- page = (void *)__get_free_page(ZCACHE_GFP_MASK);
- if (unlikely(page == NULL)) {
- zcache_failed_get_free_pages++;
- kmem_cache_free(zcache_obj_cache, obj);
- goto unlock_out;
- }
- preempt_disable();
- kp = &__get_cpu_var(zcache_preloads);
- if (kp->obj == NULL)
- kp->obj = obj;
- else
- kmem_cache_free(zcache_obj_cache, obj);
- if (kp->page == NULL)
- kp->page = page;
- else
- free_page((unsigned long)page);
- ret = 0;
-unlock_out:
- spin_unlock(&zcache_direct_reclaim_lock);
-out:
- return ret;
-}
-
-static void *zcache_get_free_page(void)
-{
- struct zcache_preload *kp;
- void *page;
-
- kp = &__get_cpu_var(zcache_preloads);
- page = kp->page;
- BUG_ON(page == NULL);
- kp->page = NULL;
- return page;
-}
-
-static void zcache_free_page(void *p)
-{
- free_page((unsigned long)p);
-}
-
-/*
- * zcache implementation for tmem host ops
- */
-
-static struct tmem_objnode *zcache_objnode_alloc(struct tmem_pool *pool)
-{
- struct tmem_objnode *objnode = NULL;
- unsigned long count;
- struct zcache_preload *kp;
-
- kp = &__get_cpu_var(zcache_preloads);
- if (kp->nr <= 0)
- goto out;
- objnode = kp->objnodes[kp->nr - 1];
- BUG_ON(objnode == NULL);
- kp->objnodes[kp->nr - 1] = NULL;
- kp->nr--;
- count = atomic_inc_return(&zcache_curr_objnode_count);
- if (count > zcache_curr_objnode_count_max)
- zcache_curr_objnode_count_max = count;
-out:
- return objnode;
-}
-
-static void zcache_objnode_free(struct tmem_objnode *objnode,
- struct tmem_pool *pool)
-{
- atomic_dec(&zcache_curr_objnode_count);
- BUG_ON(atomic_read(&zcache_curr_objnode_count) < 0);
- kmem_cache_free(zcache_objnode_cache, objnode);
-}
-
-static struct tmem_obj *zcache_obj_alloc(struct tmem_pool *pool)
-{
- struct tmem_obj *obj = NULL;
- unsigned long count;
- struct zcache_preload *kp;
-
- kp = &__get_cpu_var(zcache_preloads);
- obj = kp->obj;
- BUG_ON(obj == NULL);
- kp->obj = NULL;
- count = atomic_inc_return(&zcache_curr_obj_count);
- if (count > zcache_curr_obj_count_max)
- zcache_curr_obj_count_max = count;
- return obj;
-}
-
-static void zcache_obj_free(struct tmem_obj *obj, struct tmem_pool *pool)
-{
- atomic_dec(&zcache_curr_obj_count);
- BUG_ON(atomic_read(&zcache_curr_obj_count) < 0);
- kmem_cache_free(zcache_obj_cache, obj);
-}
-
-static struct tmem_hostops zcache_hostops = {
- .obj_alloc = zcache_obj_alloc,
- .obj_free = zcache_obj_free,
- .objnode_alloc = zcache_objnode_alloc,
- .objnode_free = zcache_objnode_free,
-};
-
-/*
- * zcache implementations for PAM page descriptor ops
- */
-
-static atomic_t zcache_curr_eph_pampd_count = ATOMIC_INIT(0);
-static unsigned long zcache_curr_eph_pampd_count_max;
-static atomic_t zcache_curr_pers_pampd_count = ATOMIC_INIT(0);
-static unsigned long zcache_curr_pers_pampd_count_max;
-
-/* forward reference */
-static int zcache_compress(struct page *from, void **out_va, size_t *out_len);
-
-static void *zcache_pampd_create(char *data, size_t size, bool raw, int eph,
- struct tmem_pool *pool, struct tmem_oid *oid,
- uint32_t index)
-{
- void *pampd = NULL, *cdata;
- size_t clen;
- int ret;
- unsigned long count;
- struct page *page = virt_to_page(data);
- struct zcache_client *cli = pool->client;
- uint16_t client_id = get_client_id_from_client(cli);
- unsigned long zv_mean_zsize;
- unsigned long curr_pers_pampd_count;
-
- if (eph) {
- ret = zcache_compress(page, &cdata, &clen);
- if (ret == 0)
- goto out;
- if (clen == 0 || clen > zbud_max_buddy_size()) {
- zcache_compress_poor++;
- goto out;
- }
- pampd = (void *)zbud_create(client_id, pool->pool_id, oid,
- index, page, cdata, clen);
- if (pampd != NULL) {
- count = atomic_inc_return(&zcache_curr_eph_pampd_count);
- if (count > zcache_curr_eph_pampd_count_max)
- zcache_curr_eph_pampd_count_max = count;
- }
- } else {
- curr_pers_pampd_count =
- atomic_read(&zcache_curr_pers_pampd_count);
- if (curr_pers_pampd_count >
- (zv_page_count_policy_percent * totalram_pages) / 100)
- goto out;
- ret = zcache_compress(page, &cdata, &clen);
- if (ret == 0)
- goto out;
- /* reject if compression is too poor */
- if (clen > zv_max_zsize) {
- zcache_compress_poor++;
- goto out;
- }
- /* reject if mean compression is too poor */
- if ((clen > zv_max_mean_zsize) && (curr_pers_pampd_count > 0)) {
- zv_mean_zsize = xv_get_total_size_bytes(cli->xvpool) /
- curr_pers_pampd_count;
- if (zv_mean_zsize > zv_max_mean_zsize) {
- zcache_mean_compress_poor++;
- goto out;
- }
- }
- pampd = (void *)zv_create(cli->xvpool, pool->pool_id,
- oid, index, cdata, clen);
- if (pampd == NULL)
- goto out;
- count = atomic_inc_return(&zcache_curr_pers_pampd_count);
- if (count > zcache_curr_pers_pampd_count_max)
- zcache_curr_pers_pampd_count_max = count;
- }
-out:
- return pampd;
-}
-
-/*
- * fill the pageframe corresponding to the struct page with the data
- * from the passed pampd
- */
-static int zcache_pampd_get_data(char *data, size_t *bufsize, bool raw,
- void *pampd, struct tmem_pool *pool,
- struct tmem_oid *oid, uint32_t index)
-{
- int ret = 0;
-
- BUG_ON(is_ephemeral(pool));
- zv_decompress(virt_to_page(data), pampd);
- return ret;
-}
-
-/*
- * fill the pageframe corresponding to the struct page with the data
- * from the passed pampd
- */
-static int zcache_pampd_get_data_and_free(char *data, size_t *bufsize, bool raw,
- void *pampd, struct tmem_pool *pool,
- struct tmem_oid *oid, uint32_t index)
-{
- int ret = 0;
-
- BUG_ON(!is_ephemeral(pool));
- zbud_decompress(virt_to_page(data), pampd);
- zbud_free_and_delist((struct zbud_hdr *)pampd);
- atomic_dec(&zcache_curr_eph_pampd_count);
- return ret;
-}
-
-/*
- * free the pampd and remove it from any zcache lists
- * pampd must no longer be pointed to from any tmem data structures!
- */
-static void zcache_pampd_free(void *pampd, struct tmem_pool *pool,
- struct tmem_oid *oid, uint32_t index)
-{
- struct zcache_client *cli = pool->client;
-
- if (is_ephemeral(pool)) {
- zbud_free_and_delist((struct zbud_hdr *)pampd);
- atomic_dec(&zcache_curr_eph_pampd_count);
- BUG_ON(atomic_read(&zcache_curr_eph_pampd_count) < 0);
- } else {
- zv_free(cli->xvpool, (struct zv_hdr *)pampd);
- atomic_dec(&zcache_curr_pers_pampd_count);
- BUG_ON(atomic_read(&zcache_curr_pers_pampd_count) < 0);
- }
-}
-
-static void zcache_pampd_free_obj(struct tmem_pool *pool, struct tmem_obj *obj)
-{
-}
-
-static void zcache_pampd_new_obj(struct tmem_obj *obj)
-{
-}
-
-static int zcache_pampd_replace_in_obj(void *pampd, struct tmem_obj *obj)
-{
- return -1;
-}
-
-static bool zcache_pampd_is_remote(void *pampd)
-{
- return 0;
-}
-
-static struct tmem_pamops zcache_pamops = {
- .create = zcache_pampd_create,
- .get_data = zcache_pampd_get_data,
- .get_data_and_free = zcache_pampd_get_data_and_free,
- .free = zcache_pampd_free,
- .free_obj = zcache_pampd_free_obj,
- .new_obj = zcache_pampd_new_obj,
- .replace_in_obj = zcache_pampd_replace_in_obj,
- .is_remote = zcache_pampd_is_remote,
-};
-
-/*
- * zcache compression/decompression and related per-cpu stuff
- */
-
-#define LZO_WORKMEM_BYTES LZO1X_1_MEM_COMPRESS
-#define LZO_DSTMEM_PAGE_ORDER 1
-static DEFINE_PER_CPU(unsigned char *, zcache_workmem);
-static DEFINE_PER_CPU(unsigned char *, zcache_dstmem);
-
-static int zcache_compress(struct page *from, void **out_va, size_t *out_len)
-{
- int ret = 0;
- unsigned char *dmem = __get_cpu_var(zcache_dstmem);
- unsigned char *wmem = __get_cpu_var(zcache_workmem);
- char *from_va;
-
- BUG_ON(!irqs_disabled());
- if (unlikely(dmem == NULL || wmem == NULL))
- goto out; /* no buffer, so can't compress */
- from_va = kmap_atomic(from, KM_USER0);
- mb();
- ret = lzo1x_1_compress(from_va, PAGE_SIZE, dmem, out_len, wmem);
- BUG_ON(ret != LZO_E_OK);
- *out_va = dmem;
- kunmap_atomic(from_va, KM_USER0);
- ret = 1;
-out:
- return ret;
-}
-
-
-static int zcache_cpu_notifier(struct notifier_block *nb,
- unsigned long action, void *pcpu)
-{
- int cpu = (long)pcpu;
- struct zcache_preload *kp;
-
- switch (action) {
- case CPU_UP_PREPARE:
- per_cpu(zcache_dstmem, cpu) = (void *)__get_free_pages(
- GFP_KERNEL | __GFP_REPEAT,
- LZO_DSTMEM_PAGE_ORDER),
- per_cpu(zcache_workmem, cpu) =
- kzalloc(LZO1X_MEM_COMPRESS,
- GFP_KERNEL | __GFP_REPEAT);
- break;
- case CPU_DEAD:
- case CPU_UP_CANCELED:
- free_pages((unsigned long)per_cpu(zcache_dstmem, cpu),
- LZO_DSTMEM_PAGE_ORDER);
- per_cpu(zcache_dstmem, cpu) = NULL;
- kfree(per_cpu(zcache_workmem, cpu));
- per_cpu(zcache_workmem, cpu) = NULL;
- kp = &per_cpu(zcache_preloads, cpu);
- while (kp->nr) {
- kmem_cache_free(zcache_objnode_cache,
- kp->objnodes[kp->nr - 1]);
- kp->objnodes[kp->nr - 1] = NULL;
- kp->nr--;
- }
- kmem_cache_free(zcache_obj_cache, kp->obj);
- free_page((unsigned long)kp->page);
- break;
- default:
- break;
- }
- return NOTIFY_OK;
-}
-
-static struct notifier_block zcache_cpu_notifier_block = {
- .notifier_call = zcache_cpu_notifier
-};
-
-#ifdef CONFIG_SYSFS
-#define ZCACHE_SYSFS_RO(_name) \
- static ssize_t zcache_##_name##_show(struct kobject *kobj, \
- struct kobj_attribute *attr, char *buf) \
- { \
- return sprintf(buf, "%lu\n", zcache_##_name); \
- } \
- static struct kobj_attribute zcache_##_name##_attr = { \
- .attr = { .name = __stringify(_name), .mode = 0444 }, \
- .show = zcache_##_name##_show, \
- }
-
-#define ZCACHE_SYSFS_RO_ATOMIC(_name) \
- static ssize_t zcache_##_name##_show(struct kobject *kobj, \
- struct kobj_attribute *attr, char *buf) \
- { \
- return sprintf(buf, "%d\n", atomic_read(&zcache_##_name)); \
- } \
- static struct kobj_attribute zcache_##_name##_attr = { \
- .attr = { .name = __stringify(_name), .mode = 0444 }, \
- .show = zcache_##_name##_show, \
- }
-
-#define ZCACHE_SYSFS_RO_CUSTOM(_name, _func) \
- static ssize_t zcache_##_name##_show(struct kobject *kobj, \
- struct kobj_attribute *attr, char *buf) \
- { \
- return _func(buf); \
- } \
- static struct kobj_attribute zcache_##_name##_attr = { \
- .attr = { .name = __stringify(_name), .mode = 0444 }, \
- .show = zcache_##_name##_show, \
- }
-
-ZCACHE_SYSFS_RO(curr_obj_count_max);
-ZCACHE_SYSFS_RO(curr_objnode_count_max);
-ZCACHE_SYSFS_RO(flush_total);
-ZCACHE_SYSFS_RO(flush_found);
-ZCACHE_SYSFS_RO(flobj_total);
-ZCACHE_SYSFS_RO(flobj_found);
-ZCACHE_SYSFS_RO(failed_eph_puts);
-ZCACHE_SYSFS_RO(failed_pers_puts);
-ZCACHE_SYSFS_RO(zbud_curr_zbytes);
-ZCACHE_SYSFS_RO(zbud_cumul_zpages);
-ZCACHE_SYSFS_RO(zbud_cumul_zbytes);
-ZCACHE_SYSFS_RO(zbud_buddied_count);
-ZCACHE_SYSFS_RO(zbpg_unused_list_count);
-ZCACHE_SYSFS_RO(evicted_raw_pages);
-ZCACHE_SYSFS_RO(evicted_unbuddied_pages);
-ZCACHE_SYSFS_RO(evicted_buddied_pages);
-ZCACHE_SYSFS_RO(failed_get_free_pages);
-ZCACHE_SYSFS_RO(failed_alloc);
-ZCACHE_SYSFS_RO(put_to_flush);
-ZCACHE_SYSFS_RO(aborted_preload);
-ZCACHE_SYSFS_RO(aborted_shrink);
-ZCACHE_SYSFS_RO(compress_poor);
-ZCACHE_SYSFS_RO(mean_compress_poor);
-ZCACHE_SYSFS_RO_ATOMIC(zbud_curr_raw_pages);
-ZCACHE_SYSFS_RO_ATOMIC(zbud_curr_zpages);
-ZCACHE_SYSFS_RO_ATOMIC(curr_obj_count);
-ZCACHE_SYSFS_RO_ATOMIC(curr_objnode_count);
-ZCACHE_SYSFS_RO_CUSTOM(zbud_unbuddied_list_counts,
- zbud_show_unbuddied_list_counts);
-ZCACHE_SYSFS_RO_CUSTOM(zbud_cumul_chunk_counts,
- zbud_show_cumul_chunk_counts);
-ZCACHE_SYSFS_RO_CUSTOM(zv_curr_dist_counts,
- zv_curr_dist_counts_show);
-ZCACHE_SYSFS_RO_CUSTOM(zv_cumul_dist_counts,
- zv_cumul_dist_counts_show);
-
-static struct attribute *zcache_attrs[] = {
- &zcache_curr_obj_count_attr.attr,
- &zcache_curr_obj_count_max_attr.attr,
- &zcache_curr_objnode_count_attr.attr,
- &zcache_curr_objnode_count_max_attr.attr,
- &zcache_flush_total_attr.attr,
- &zcache_flobj_total_attr.attr,
- &zcache_flush_found_attr.attr,
- &zcache_flobj_found_attr.attr,
- &zcache_failed_eph_puts_attr.attr,
- &zcache_failed_pers_puts_attr.attr,
- &zcache_compress_poor_attr.attr,
- &zcache_mean_compress_poor_attr.attr,
- &zcache_zbud_curr_raw_pages_attr.attr,
- &zcache_zbud_curr_zpages_attr.attr,
- &zcache_zbud_curr_zbytes_attr.attr,
- &zcache_zbud_cumul_zpages_attr.attr,
- &zcache_zbud_cumul_zbytes_attr.attr,
- &zcache_zbud_buddied_count_attr.attr,
- &zcache_zbpg_unused_list_count_attr.attr,
- &zcache_evicted_raw_pages_attr.attr,
- &zcache_evicted_unbuddied_pages_attr.attr,
- &zcache_evicted_buddied_pages_attr.attr,
- &zcache_failed_get_free_pages_attr.attr,
- &zcache_failed_alloc_attr.attr,
- &zcache_put_to_flush_attr.attr,
- &zcache_aborted_preload_attr.attr,
- &zcache_aborted_shrink_attr.attr,
- &zcache_zbud_unbuddied_list_counts_attr.attr,
- &zcache_zbud_cumul_chunk_counts_attr.attr,
- &zcache_zv_curr_dist_counts_attr.attr,
- &zcache_zv_cumul_dist_counts_attr.attr,
- &zcache_zv_max_zsize_attr.attr,
- &zcache_zv_max_mean_zsize_attr.attr,
- &zcache_zv_page_count_policy_percent_attr.attr,
- NULL,
-};
-
-static struct attribute_group zcache_attr_group = {
- .attrs = zcache_attrs,
- .name = "zcache",
-};
-
-#endif /* CONFIG_SYSFS */
-/*
- * When zcache is disabled ("frozen"), pools can be created and destroyed,
- * but all puts (and thus all other operations that require memory allocation)
- * must fail. If zcache is unfrozen, accepts puts, then frozen again,
- * data consistency requires all puts while frozen to be converted into
- * flushes.
- */
-static bool zcache_freeze;
-
-/*
- * zcache shrinker interface (only useful for ephemeral pages, so zbud only)
- */
-static int shrink_zcache_memory(struct shrinker *shrink,
- struct shrink_control *sc)
-{
- int ret = -1;
- int nr = sc->nr_to_scan;
- gfp_t gfp_mask = sc->gfp_mask;
-
- if (nr >= 0) {
- if (!(gfp_mask & __GFP_FS))
- /* does this case really need to be skipped? */
- goto out;
- if (spin_trylock(&zcache_direct_reclaim_lock)) {
- zbud_evict_pages(nr);
- spin_unlock(&zcache_direct_reclaim_lock);
- } else
- zcache_aborted_shrink++;
- }
- ret = (int)atomic_read(&zcache_zbud_curr_raw_pages);
-out:
- return ret;
-}
-
-static struct shrinker zcache_shrinker = {
- .shrink = shrink_zcache_memory,
- .seeks = DEFAULT_SEEKS,
-};
-
-/*
- * zcache shims between cleancache/frontswap ops and tmem
- */
-
-static int zcache_put_page(int cli_id, int pool_id, struct tmem_oid *oidp,
- uint32_t index, struct page *page)
-{
- struct tmem_pool *pool;
- int ret = -1;
-
- BUG_ON(!irqs_disabled());
- pool = zcache_get_pool_by_id(cli_id, pool_id);
- if (unlikely(pool == NULL))
- goto out;
- if (!zcache_freeze && zcache_do_preload(pool) == 0) {
- /* preload does preempt_disable on success */
- ret = tmem_put(pool, oidp, index, page_address(page),
- PAGE_SIZE, 0, is_ephemeral(pool));
- if (ret < 0) {
- if (is_ephemeral(pool))
- zcache_failed_eph_puts++;
- else
- zcache_failed_pers_puts++;
- }
- zcache_put_pool(pool);
- preempt_enable_no_resched();
- } else {
- zcache_put_to_flush++;
- if (atomic_read(&pool->obj_count) > 0)
- /* the put fails whether the flush succeeds or not */
- (void)tmem_flush_page(pool, oidp, index);
- zcache_put_pool(pool);
- }
-out:
- return ret;
-}
-
-static int zcache_get_page(int cli_id, int pool_id, struct tmem_oid *oidp,
- uint32_t index, struct page *page)
-{
- struct tmem_pool *pool;
- int ret = -1;
- unsigned long flags;
- size_t size = PAGE_SIZE;
-
- local_irq_save(flags);
- pool = zcache_get_pool_by_id(cli_id, pool_id);
- if (likely(pool != NULL)) {
- if (atomic_read(&pool->obj_count) > 0)
- ret = tmem_get(pool, oidp, index, page_address(page),
- &size, 0, is_ephemeral(pool));
- zcache_put_pool(pool);
- }
- local_irq_restore(flags);
- return ret;
-}
-
-static int zcache_flush_page(int cli_id, int pool_id,
- struct tmem_oid *oidp, uint32_t index)
-{
- struct tmem_pool *pool;
- int ret = -1;
- unsigned long flags;
-
- local_irq_save(flags);
- zcache_flush_total++;
- pool = zcache_get_pool_by_id(cli_id, pool_id);
- if (likely(pool != NULL)) {
- if (atomic_read(&pool->obj_count) > 0)
- ret = tmem_flush_page(pool, oidp, index);
- zcache_put_pool(pool);
- }
- if (ret >= 0)
- zcache_flush_found++;
- local_irq_restore(flags);
- return ret;
-}
-
-static int zcache_flush_object(int cli_id, int pool_id,
- struct tmem_oid *oidp)
-{
- struct tmem_pool *pool;
- int ret = -1;
- unsigned long flags;
-
- local_irq_save(flags);
- zcache_flobj_total++;
- pool = zcache_get_pool_by_id(cli_id, pool_id);
- if (likely(pool != NULL)) {
- if (atomic_read(&pool->obj_count) > 0)
- ret = tmem_flush_object(pool, oidp);
- zcache_put_pool(pool);
- }
- if (ret >= 0)
- zcache_flobj_found++;
- local_irq_restore(flags);
- return ret;
-}
-
-static int zcache_destroy_pool(int cli_id, int pool_id)
-{
- struct tmem_pool *pool = NULL;
- struct zcache_client *cli = NULL;
- int ret = -1;
-
- if (pool_id < 0)
- goto out;
- if (cli_id == LOCAL_CLIENT)
- cli = &zcache_host;
- else if ((unsigned int)cli_id < MAX_CLIENTS)
- cli = &zcache_clients[cli_id];
- if (cli == NULL)
- goto out;
- atomic_inc(&cli->refcount);
- pool = cli->tmem_pools[pool_id];
- if (pool == NULL)
- goto out;
- cli->tmem_pools[pool_id] = NULL;
- /* wait for pool activity on other cpus to quiesce */
- while (atomic_read(&pool->refcount) != 0)
- ;
- atomic_dec(&cli->refcount);
- local_bh_disable();
- ret = tmem_destroy_pool(pool);
- local_bh_enable();
- kfree(pool);
- pr_info("zcache: destroyed pool id=%d, cli_id=%d\n",
- pool_id, cli_id);
-out:
- return ret;
-}
-
-static int zcache_new_pool(uint16_t cli_id, uint32_t flags)
-{
- int poolid = -1;
- struct tmem_pool *pool;
- struct zcache_client *cli = NULL;
-
- if (cli_id == LOCAL_CLIENT)
- cli = &zcache_host;
- else if ((unsigned int)cli_id < MAX_CLIENTS)
- cli = &zcache_clients[cli_id];
- if (cli == NULL)
- goto out;
- atomic_inc(&cli->refcount);
- pool = kmalloc(sizeof(struct tmem_pool), GFP_KERNEL);
- if (pool == NULL) {
- pr_info("zcache: pool creation failed: out of memory\n");
- goto out;
- }
-
- for (poolid = 0; poolid < MAX_POOLS_PER_CLIENT; poolid++)
- if (cli->tmem_pools[poolid] == NULL)
- break;
- if (poolid >= MAX_POOLS_PER_CLIENT) {
- pr_info("zcache: pool creation failed: max exceeded\n");
- kfree(pool);
- poolid = -1;
- goto out;
- }
- atomic_set(&pool->refcount, 0);
- pool->client = cli;
- pool->pool_id = poolid;
- tmem_new_pool(pool, flags);
- cli->tmem_pools[poolid] = pool;
- pr_info("zcache: created %s tmem pool, id=%d, client=%d\n",
- flags & TMEM_POOL_PERSIST ? "persistent" : "ephemeral",
- poolid, cli_id);
-out:
- if (cli != NULL)
- atomic_dec(&cli->refcount);
- return poolid;
-}
-
-/**********
- * Two kernel functionalities currently can be layered on top of tmem.
- * These are "cleancache" which is used as a second-chance cache for clean
- * page cache pages; and "frontswap" which is used for swap pages
- * to avoid writes to disk. A generic "shim" is provided here for each
- * to translate in-kernel semantics to zcache semantics.
- */
-
-#ifdef CONFIG_CLEANCACHE
-static void zcache_cleancache_put_page(int pool_id,
- struct cleancache_filekey key,
- pgoff_t index, struct page *page)
-{
- u32 ind = (u32) index;
- struct tmem_oid oid = *(struct tmem_oid *)&key;
-
- if (likely(ind == index))
- (void)zcache_put_page(LOCAL_CLIENT, pool_id, &oid, index, page);
-}
-
-static int zcache_cleancache_get_page(int pool_id,
- struct cleancache_filekey key,
- pgoff_t index, struct page *page)
-{
- u32 ind = (u32) index;
- struct tmem_oid oid = *(struct tmem_oid *)&key;
- int ret = -1;
-
- if (likely(ind == index))
- ret = zcache_get_page(LOCAL_CLIENT, pool_id, &oid, index, page);
- return ret;
-}
-
-static void zcache_cleancache_flush_page(int pool_id,
- struct cleancache_filekey key,
- pgoff_t index)
-{
- u32 ind = (u32) index;
- struct tmem_oid oid = *(struct tmem_oid *)&key;
-
- if (likely(ind == index))
- (void)zcache_flush_page(LOCAL_CLIENT, pool_id, &oid, ind);
-}
-
-static void zcache_cleancache_flush_inode(int pool_id,
- struct cleancache_filekey key)
-{
- struct tmem_oid oid = *(struct tmem_oid *)&key;
-
- (void)zcache_flush_object(LOCAL_CLIENT, pool_id, &oid);
-}
-
-static void zcache_cleancache_flush_fs(int pool_id)
-{
- if (pool_id >= 0)
- (void)zcache_destroy_pool(LOCAL_CLIENT, pool_id);
-}
-
-static int zcache_cleancache_init_fs(size_t pagesize)
-{
- BUG_ON(sizeof(struct cleancache_filekey) !=
- sizeof(struct tmem_oid));
- BUG_ON(pagesize != PAGE_SIZE);
- return zcache_new_pool(LOCAL_CLIENT, 0);
-}
-
-static int zcache_cleancache_init_shared_fs(char *uuid, size_t pagesize)
-{
- /* shared pools are unsupported and map to private */
- BUG_ON(sizeof(struct cleancache_filekey) !=
- sizeof(struct tmem_oid));
- BUG_ON(pagesize != PAGE_SIZE);
- return zcache_new_pool(LOCAL_CLIENT, 0);
-}
-
-static struct cleancache_ops zcache_cleancache_ops = {
- .put_page = zcache_cleancache_put_page,
- .get_page = zcache_cleancache_get_page,
- .flush_page = zcache_cleancache_flush_page,
- .flush_inode = zcache_cleancache_flush_inode,
- .flush_fs = zcache_cleancache_flush_fs,
- .init_shared_fs = zcache_cleancache_init_shared_fs,
- .init_fs = zcache_cleancache_init_fs
-};
-
-struct cleancache_ops zcache_cleancache_register_ops(void)
-{
- struct cleancache_ops old_ops =
- cleancache_register_ops(&zcache_cleancache_ops);
-
- return old_ops;
-}
-#endif
-
-#ifdef CONFIG_FRONTSWAP
-/* a single tmem poolid is used for all frontswap "types" (swapfiles) */
-static int zcache_frontswap_poolid = -1;
-
-/*
- * Swizzling increases objects per swaptype, increasing tmem concurrency
- * for heavy swaploads. Later, larger nr_cpus -> larger SWIZ_BITS
- */
-#define SWIZ_BITS 4
-#define SWIZ_MASK ((1 << SWIZ_BITS) - 1)
-#define _oswiz(_type, _ind) ((_type << SWIZ_BITS) | (_ind & SWIZ_MASK))
-#define iswiz(_ind) (_ind >> SWIZ_BITS)
-
-static inline struct tmem_oid oswiz(unsigned type, u32 ind)
-{
- struct tmem_oid oid = { .oid = { 0 } };
- oid.oid[0] = _oswiz(type, ind);
- return oid;
-}
-
-static int zcache_frontswap_put_page(unsigned type, pgoff_t offset,
- struct page *page)
-{
- u64 ind64 = (u64)offset;
- u32 ind = (u32)offset;
- struct tmem_oid oid = oswiz(type, ind);
- int ret = -1;
- unsigned long flags;
-
- BUG_ON(!PageLocked(page));
- if (likely(ind64 == ind)) {
- local_irq_save(flags);
- ret = zcache_put_page(LOCAL_CLIENT, zcache_frontswap_poolid,
- &oid, iswiz(ind), page);
- local_irq_restore(flags);
- }
- return ret;
-}
-
-/* returns 0 if the page was successfully gotten from frontswap, -1 if
- * was not present (should never happen!) */
-static int zcache_frontswap_get_page(unsigned type, pgoff_t offset,
- struct page *page)
-{
- u64 ind64 = (u64)offset;
- u32 ind = (u32)offset;
- struct tmem_oid oid = oswiz(type, ind);
- int ret = -1;
-
- BUG_ON(!PageLocked(page));
- if (likely(ind64 == ind))
- ret = zcache_get_page(LOCAL_CLIENT, zcache_frontswap_poolid,
- &oid, iswiz(ind), page);
- return ret;
-}
-
-/* flush a single page from frontswap */
-static void zcache_frontswap_flush_page(unsigned type, pgoff_t offset)
-{
- u64 ind64 = (u64)offset;
- u32 ind = (u32)offset;
- struct tmem_oid oid = oswiz(type, ind);
-
- if (likely(ind64 == ind))
- (void)zcache_flush_page(LOCAL_CLIENT, zcache_frontswap_poolid,
- &oid, iswiz(ind));
-}
-
-/* flush all pages from the passed swaptype */
-static void zcache_frontswap_flush_area(unsigned type)
-{
- struct tmem_oid oid;
- int ind;
-
- for (ind = SWIZ_MASK; ind >= 0; ind--) {
- oid = oswiz(type, ind);
- (void)zcache_flush_object(LOCAL_CLIENT,
- zcache_frontswap_poolid, &oid);
- }
-}
-
-static void zcache_frontswap_init(unsigned ignored)
-{
- /* a single tmem poolid is used for all frontswap "types" (swapfiles) */
- if (zcache_frontswap_poolid < 0)
- zcache_frontswap_poolid =
- zcache_new_pool(LOCAL_CLIENT, TMEM_POOL_PERSIST);
-}
-
-static struct frontswap_ops zcache_frontswap_ops = {
- .put_page = zcache_frontswap_put_page,
- .get_page = zcache_frontswap_get_page,
- .flush_page = zcache_frontswap_flush_page,
- .flush_area = zcache_frontswap_flush_area,
- .init = zcache_frontswap_init
-};
-
-struct frontswap_ops zcache_frontswap_register_ops(void)
-{
- struct frontswap_ops old_ops =
- frontswap_register_ops(&zcache_frontswap_ops);
-
- return old_ops;
-}
-#endif
-
-/*
- * zcache initialization
- * NOTE FOR NOW zcache MUST BE PROVIDED AS A KERNEL BOOT PARAMETER OR
- * NOTHING HAPPENS!
- */
-
-static int zcache_enabled;
-
-static int __init enable_zcache(char *s)
-{
- zcache_enabled = 1;
- return 1;
-}
-__setup("zcache", enable_zcache);
-
-/* allow independent dynamic disabling of cleancache and frontswap */
-
-static int use_cleancache = 1;
-
-static int __init no_cleancache(char *s)
-{
- use_cleancache = 0;
- return 1;
-}
-
-__setup("nocleancache", no_cleancache);
-
-static int use_frontswap = 1;
-
-static int __init no_frontswap(char *s)
-{
- use_frontswap = 0;
- return 1;
-}
-
-__setup("nofrontswap", no_frontswap);
-
-static int __init zcache_init(void)
-{
-#ifdef CONFIG_SYSFS
- int ret = 0;
-
- ret = sysfs_create_group(mm_kobj, &zcache_attr_group);
- if (ret) {
- pr_err("zcache: can't create sysfs\n");
- goto out;
- }
-#endif /* CONFIG_SYSFS */
-#if defined(CONFIG_CLEANCACHE) || defined(CONFIG_FRONTSWAP)
- if (zcache_enabled) {
- unsigned int cpu;
-
- tmem_register_hostops(&zcache_hostops);
- tmem_register_pamops(&zcache_pamops);
- ret = register_cpu_notifier(&zcache_cpu_notifier_block);
- if (ret) {
- pr_err("zcache: can't register cpu notifier\n");
- goto out;
- }
- for_each_online_cpu(cpu) {
- void *pcpu = (void *)(long)cpu;
- zcache_cpu_notifier(&zcache_cpu_notifier_block,
- CPU_UP_PREPARE, pcpu);
- }
- }
- zcache_objnode_cache = kmem_cache_create("zcache_objnode",
- sizeof(struct tmem_objnode), 0, 0, NULL);
- zcache_obj_cache = kmem_cache_create("zcache_obj",
- sizeof(struct tmem_obj), 0, 0, NULL);
- ret = zcache_new_client(LOCAL_CLIENT);
- if (ret) {
- pr_err("zcache: can't create client\n");
- goto out;
- }
-#endif
-#ifdef CONFIG_CLEANCACHE
- if (zcache_enabled && use_cleancache) {
- struct cleancache_ops old_ops;
-
- zbud_init();
- register_shrinker(&zcache_shrinker);
- old_ops = zcache_cleancache_register_ops();
- pr_info("zcache: cleancache enabled using kernel "
- "transcendent memory and compression buddies\n");
- if (old_ops.init_fs != NULL)
- pr_warning("zcache: cleancache_ops overridden");
- }
-#endif
-#ifdef CONFIG_FRONTSWAP
- if (zcache_enabled && use_frontswap) {
- struct frontswap_ops old_ops;
-
- old_ops = zcache_frontswap_register_ops();
- pr_info("zcache: frontswap enabled using kernel "
- "transcendent memory and xvmalloc\n");
- if (old_ops.init != NULL)
- pr_warning("ktmem: frontswap_ops overridden");
- }
-#endif
-out:
- return ret;
-}
-
-module_init(zcache_init)
dev_err(dev, "usb_bulk_msg returned %d\n", rv);
goto exit;
}
- } while ((actual = max_size) &&
+ } while ((actual == max_size) &&
(n < USBTMC_MAX_READS_TO_CLEAR_BULK_IN));
if (actual == max_size) {
}
if (usb_endpoint_xfer_isoc(&ep->desc))
- max_tx = ep->desc.wMaxPacketSize * (desc->bMaxBurst + 1) *
- (desc->bmAttributes + 1);
+ max_tx = (desc->bMaxBurst + 1) * (desc->bmAttributes + 1) *
+ le16_to_cpu(ep->desc.wMaxPacketSize);
else if (usb_endpoint_xfer_int(&ep->desc))
- max_tx = ep->desc.wMaxPacketSize * (desc->bMaxBurst + 1);
+ max_tx = le16_to_cpu(ep->desc.wMaxPacketSize) *
+ (desc->bMaxBurst + 1);
else
max_tx = 999999;
if (le16_to_cpu(desc->wBytesPerInterval) > max_tx) {
"config %d interface %d altsetting %d ep %d: "
"setting to %d\n",
usb_endpoint_xfer_isoc(&ep->desc) ? "Isoc" : "Int",
- desc->wBytesPerInterval,
+ le16_to_cpu(desc->wBytesPerInterval),
cfgno, inum, asnum, ep->desc.bEndpointAddress,
max_tx);
- ep->ss_ep_comp.wBytesPerInterval = max_tx;
+ ep->ss_ep_comp.wBytesPerInterval = cpu_to_le16(max_tx);
}
}
# musb builds in ../musb along with host support
config USB_GADGET_MUSB_HDRC
tristate "Inventra HDRC USB Peripheral (TI, ADI, ...)"
- depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG)
+ depends on USB_MUSB_HDRC
select USB_GADGET_DUALSPEED
help
This OTG-capable silicon IP is used in dual designs including
#include <linux/list.h>
#include <linux/interrupt.h>
#include <linux/proc_fs.h>
+#include <linux/prefetch.h>
#include <linux/clk.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
cdev->desc.bMaxPacketSize0 =
cdev->gadget->ep0->maxpacket;
if (gadget_is_superspeed(gadget)) {
- if (gadget->speed >= USB_SPEED_SUPER)
+ if (gadget->speed >= USB_SPEED_SUPER) {
cdev->desc.bcdUSB = cpu_to_le16(0x0300);
- else
+ cdev->desc.bMaxPacketSize0 = 9;
+ } else {
cdev->desc.bcdUSB = cpu_to_le16(0x0210);
+ }
}
value = min(w_length, (u16) sizeof cdev->desc);
case ((USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_INTERFACE) << 8
| USB_REQ_GET_DESCRIPTOR):
switch (value >> 8) {
+ case HID_DT_HID:
+ VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: HID\n");
+ length = min_t(unsigned short, length,
+ hidg_desc.bLength);
+ memcpy(req->buf, &hidg_desc, length);
+ goto respond;
+ break;
case HID_DT_REPORT:
VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: REPORT\n");
length = min_t(unsigned short, length,
}
}
-#if 0
-static void fusb300_dbg_fifo(struct fusb300_ep *ep,
- u8 entry, u16 length)
-{
- u32 reg;
- u32 i = 0;
- u32 j = 0;
-
- reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_GTM);
- reg &= ~(FUSB300_GTM_TST_EP_ENTRY(0xF) |
- FUSB300_GTM_TST_EP_NUM(0xF) | FUSB300_GTM_TST_FIFO_DEG);
- reg |= (FUSB300_GTM_TST_EP_ENTRY(entry) |
- FUSB300_GTM_TST_EP_NUM(ep->epnum) | FUSB300_GTM_TST_FIFO_DEG);
- iowrite32(reg, ep->fusb300->reg + FUSB300_OFFSET_GTM);
-
- for (i = 0; i < (length >> 2); i++) {
- if (i * 4 == 1024)
- break;
- reg = ioread32(ep->fusb300->reg +
- FUSB300_OFFSET_BUFDBG_START + i * 4);
- printk(KERN_DEBUG" 0x%-8x", reg);
- j++;
- if ((j % 4) == 0)
- printk(KERN_DEBUG "\n");
- }
-
- if (length % 4) {
- reg = ioread32(ep->fusb300->reg +
- FUSB300_OFFSET_BUFDBG_START + i * 4);
- printk(KERN_DEBUG " 0x%x\n", reg);
- }
-
- if ((j % 4) != 0)
- printk(KERN_DEBUG "\n");
-
- fusb300_disable_bit(ep->fusb300, FUSB300_OFFSET_GTM,
- FUSB300_GTM_TST_FIFO_DEG);
-}
-
-static void fusb300_cmp_dbg_fifo(struct fusb300_ep *ep,
- u8 entry, u16 length, u8 *golden)
-{
- u32 reg;
- u32 i = 0;
- u32 golden_value;
- u8 *tmp;
-
- tmp = golden;
-
- printk(KERN_DEBUG "fusb300_cmp_dbg_fifo (entry %d) : start\n", entry);
-
- reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_GTM);
- reg &= ~(FUSB300_GTM_TST_EP_ENTRY(0xF) |
- FUSB300_GTM_TST_EP_NUM(0xF) | FUSB300_GTM_TST_FIFO_DEG);
- reg |= (FUSB300_GTM_TST_EP_ENTRY(entry) |
- FUSB300_GTM_TST_EP_NUM(ep->epnum) | FUSB300_GTM_TST_FIFO_DEG);
- iowrite32(reg, ep->fusb300->reg + FUSB300_OFFSET_GTM);
-
- for (i = 0; i < (length >> 2); i++) {
- if (i * 4 == 1024)
- break;
- golden_value = *tmp | *(tmp + 1) << 8 |
- *(tmp + 2) << 16 | *(tmp + 3) << 24;
-
- reg = ioread32(ep->fusb300->reg +
- FUSB300_OFFSET_BUFDBG_START + i*4);
-
- if (reg != golden_value) {
- printk(KERN_DEBUG "0x%x : ", (u32)(ep->fusb300->reg +
- FUSB300_OFFSET_BUFDBG_START + i*4));
- printk(KERN_DEBUG " golden = 0x%x, reg = 0x%x\n",
- golden_value, reg);
- }
- tmp += 4;
- }
-
- switch (length % 4) {
- case 1:
- golden_value = *tmp;
- case 2:
- golden_value = *tmp | *(tmp + 1) << 8;
- case 3:
- golden_value = *tmp | *(tmp + 1) << 8 | *(tmp + 2) << 16;
- default:
- break;
-
- reg = ioread32(ep->fusb300->reg + FUSB300_OFFSET_BUFDBG_START + i*4);
- if (reg != golden_value) {
- printk(KERN_DEBUG "0x%x:", (u32)(ep->fusb300->reg +
- FUSB300_OFFSET_BUFDBG_START + i*4));
- printk(KERN_DEBUG " golden = 0x%x, reg = 0x%x\n",
- golden_value, reg);
- }
- }
-
- printk(KERN_DEBUG "fusb300_cmp_dbg_fifo : end\n");
- fusb300_disable_bit(ep->fusb300, FUSB300_OFFSET_GTM,
- FUSB300_GTM_TST_FIFO_DEG);
-}
-#endif
-
static void fusb300_rdfifo(struct fusb300_ep *ep,
struct fusb300_request *req,
u32 length)
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/ioport.h>
-#include <linux/irq.h>
#include <linux/kernel.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/pci.h>
#include <linux/platform_device.h>
+#include <linux/prefetch.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/timer.h>
static const struct platform_device_id s3c_udc_ids[] = {
{ "s3c2410-usbgadget", },
{ "s3c2440-usbgadget", },
+ { }
};
MODULE_DEVICE_TABLE(platform, s3c_udc_ids);
if (!selector || selector > 5)
goto error;
ehci_quiesce(ehci);
+
+ /* Put all enabled ports into suspend */
+ while (ports--) {
+ u32 __iomem *sreg =
+ &ehci->regs->port_status[ports];
+
+ temp = ehci_readl(ehci, sreg) & ~PORT_RWC_BITS;
+ if (temp & PORT_PE)
+ ehci_writel(ehci, temp | PORT_SUSPEND,
+ sreg);
+ }
ehci_halt(ehci);
+ temp = ehci_readl(ehci, status_reg);
temp |= selector << 16;
ehci_writel(ehci, temp, status_reg);
break;
#include <linux/usb/ulpi.h>
#include <linux/slab.h>
+#include <mach/hardware.h>
#include <mach/mxc_ehci.h>
#include <asm/mach-types.h>
}
}
+static void disable_put_regulator(
+ struct ehci_hcd_omap_platform_data *pdata)
+{
+ int i;
+
+ for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
+ if (pdata->regulator[i]) {
+ regulator_disable(pdata->regulator[i]);
+ regulator_put(pdata->regulator[i]);
+ }
+ }
+}
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
omap_usbhs_disable(dev);
err_enable:
+ disable_put_regulator(pdata);
usb_put_hcd(hcd);
err_io:
+ iounmap(regs);
return ret;
}
usb_remove_hcd(hcd);
omap_usbhs_disable(dev);
+ disable_put_regulator(dev->platform_data);
+ iounmap(hcd->regs);
usb_put_hcd(hcd);
return 0;
}
int retval = 0;
spin_lock_irqsave(&priv->lock, spinflags);
+ retval = usb_hcd_check_unlink_urb(hcd, urb, status);
+ if (retval)
+ goto out;
qh = urb->ep->hcpriv;
if (!qh) {
iounmap(base);
}
-static const struct dmi_system_id __initconst ehci_dmi_nohandoff_table[] = {
+static const struct dmi_system_id __devinitconst ehci_dmi_nohandoff_table[] = {
{
/* Pegatron Lucid (ExoPC) */
.matches = {
/* If the BIOS owns the HC, signal that the OS wants it, and wait */
if (val & XHCI_HC_BIOS_OWNED) {
- writel(val & XHCI_HC_OS_OWNED, base + ext_cap_offset);
+ writel(val | XHCI_HC_OS_OWNED, base + ext_cap_offset);
/* Wait for 5 seconds with 10 microsecond polling interval */
timeout = handshake(base + ext_cap_offset, XHCI_HC_BIOS_OWNED,
spin_lock_irqsave(&xhci->lock, flags);
temp = xhci_readl(xhci, &xhci->op_regs->status);
xhci_dbg(xhci, "op reg status = 0x%x\n", temp);
- if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING)) {
+ if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING) ||
+ (xhci->xhc_state & XHCI_STATE_HALTED)) {
xhci_dbg(xhci, "HW died, polling stopped.\n");
spin_unlock_irqrestore(&xhci->lock, flags);
return;
return 0;
}
+ xhci = hcd_to_xhci(hcd);
+ if (xhci->xhc_state & XHCI_STATE_HALTED)
+ return -ENODEV;
+
if (check_virt_dev) {
- xhci = hcd_to_xhci(hcd);
if (!udev->slot_id || !xhci->devs
|| !xhci->devs[udev->slot_id]) {
printk(KERN_DEBUG "xHCI %s called with unaddressed "
xhci_urb_free_priv(xhci, urb_priv);
return ret;
}
- if (xhci->xhc_state & XHCI_STATE_DYING) {
+ if ((xhci->xhc_state & XHCI_STATE_DYING) ||
+ (xhci->xhc_state & XHCI_STATE_HALTED)) {
xhci_dbg(xhci, "Ep 0x%x: URB %p to be canceled on "
"non-responsive xHCI host.\n",
urb->ep->desc.bEndpointAddress, urb);
int i, ret;
ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
- if (ret <= 0)
+ /* If the host is halted due to driver unload, we still need to free the
+ * device.
+ */
+ if (ret <= 0 && ret != -ENODEV)
return;
virt_dev = xhci->devs[udev->slot_id];
spin_lock_irqsave(&xhci->lock, flags);
/* Don't disable the slot if the host controller is dead. */
state = xhci_readl(xhci, &xhci->op_regs->status);
- if (state == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING)) {
+ if (state == 0xffffffff || (xhci->xhc_state & XHCI_STATE_DYING) ||
+ (xhci->xhc_state & XHCI_STATE_HALTED)) {
xhci_free_virt_device(xhci, udev->slot_id);
spin_unlock_irqrestore(&xhci->lock, flags);
return;
# for silicon based on Mentor Graphics INVENTRA designs
#
-comment "Enable Host or Gadget support to see Inventra options"
- depends on !USB && USB_GADGET=n
-
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
config USB_MUSB_HDRC
depends on USB && USB_GADGET
is_on = !!is_on;
+ pm_runtime_get_sync(musb->controller);
+
/* NOTE: this assumes we are sensing vbus; we'd rather
* not pullup unless the B-session is active.
*/
musb_pullup(musb, is_on);
}
spin_unlock_irqrestore(&musb->lock, flags);
+
+ pm_runtime_put(musb->controller);
+
return 0;
}
u32 reg = musb_readl(chdat->tbase, TUSB_DMA_EP_MAP);
if (reg != 0) {
- dev_dbg(musb->controller, "ep%i dmareq0 is busy for ep%i\n",
+ dev_dbg(chdat->musb->controller, "ep%i dmareq0 is busy for ep%i\n",
chdat->epnum, reg & 0xf);
return -EAGAIN;
}
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*
*/
+#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/platform_device.h>
struct usbhsg_gpriv, mod)
#define __usbhsg_for_each_uep(start, pos, g, i) \
- for (i = start, pos = (g)->uep; \
+ for (i = start, pos = (g)->uep + i; \
i < (g)->uep_size; \
i++, pos = (g)->uep + i)
* /sys/bus/usb/ftdi_sio/new_id, then send patch/report!
*/
static struct usb_device_id id_table_combined [] = {
+ { USB_DEVICE(FTDI_VID, FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CTI_MINI_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CTI_NANO_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_AMC232_PID) },
case FT2232H: /* FT2232H chip */
case FT4232H: /* FT4232H chip */
case FT232H: /* FT232H chip */
- if ((baud <= 12000000) & (baud >= 1200)) {
+ if ((baud <= 12000000) && (baud >= 1200)) {
div_value = ftdi_2232h_baud_to_divisor(baud);
} else if (baud < 1200) {
div_value = ftdi_232bm_baud_to_divisor(baud);
urb_index_value = get_ftdi_divisor(tty, port);
urb_value = (__u16)urb_index_value;
urb_index = (__u16)(urb_index_value >> 16);
- if (priv->interface) { /* FT2232C */
+ if ((priv->chip_type == FT2232C) || (priv->chip_type == FT2232H) ||
+ (priv->chip_type == FT4232H) || (priv->chip_type == FT232H)) {
+ /* Probably the BM type needs the MSB of the encoded fractional
+ * divider also moved like for the chips above. Any infos? */
urb_index = (__u16)((urb_index << 8) | priv->interface);
}
/* USB-Nano-485*/
#define FTDI_CTI_NANO_PID 0xF60B
-
+/*
+ * ZeitControl cardsystems GmbH rfid-readers http://zeitconrol.de
+ */
+/* TagTracer MIFARE*/
+#define FTDI_ZEITCONTROL_TAGTRACE_MIFARE_PID 0xF7C0
#define HUAWEI_PRODUCT_K4505 0x1464
#define HUAWEI_PRODUCT_K3765 0x1465
#define HUAWEI_PRODUCT_E14AC 0x14AC
+#define HUAWEI_PRODUCT_K3770 0x14C9
+#define HUAWEI_PRODUCT_K3771 0x14CA
+#define HUAWEI_PRODUCT_K4510 0x14CB
+#define HUAWEI_PRODUCT_K4511 0x14CC
#define HUAWEI_PRODUCT_ETS1220 0x1803
#define HUAWEI_PRODUCT_E353 0x1506
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3765, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_ETS1220, 0xff, 0xff, 0xff) },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E14AC, 0xff, 0xff, 0xff) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x31) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3770, 0xff, 0x02, 0x32) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3771, 0xff, 0x02, 0x31) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K3771, 0xff, 0x02, 0x32) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4510, 0xff, 0x01, 0x31) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4510, 0xff, 0x01, 0x32) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4511, 0xff, 0x01, 0x31) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4511, 0xff, 0x01, 0x32) },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E353, 0xff, 0x01, 0x01) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V640) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V620) },
{USB_DEVICE(0x05c6, 0x9203)}, /* Generic Gobi Modem device */
{USB_DEVICE(0x05c6, 0x9222)}, /* Generic Gobi Modem device */
{USB_DEVICE(0x05c6, 0x9008)}, /* Generic Gobi QDL device */
+ {USB_DEVICE(0x05c6, 0x9009)}, /* Generic Gobi Modem device */
{USB_DEVICE(0x05c6, 0x9201)}, /* Generic Gobi QDL device */
{USB_DEVICE(0x05c6, 0x9221)}, /* Generic Gobi QDL device */
{USB_DEVICE(0x05c6, 0x9231)}, /* Generic Gobi QDL device */
{USB_DEVICE(0x1199, 0x9008)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{USB_DEVICE(0x1199, 0x9009)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{USB_DEVICE(0x1199, 0x900a)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {USB_DEVICE(0x1199, 0x9011)}, /* Sierra Wireless Gobi 2000 Modem device (MC8305) */
{USB_DEVICE(0x16d8, 0x8001)}, /* CMDTech Gobi 2000 QDL device (VU922) */
{USB_DEVICE(0x16d8, 0x8002)}, /* CMDTech Gobi 2000 Modem device (VU922) */
{USB_DEVICE(0x05c6, 0x9204)}, /* Gobi 2000 QDL device */
"Micro Mini 1GB",
USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NOT_LOCKABLE ),
+/*
+ * Nick Bowler <nbowler@elliptictech.com>
+ * SCSI stack spams (otherwise harmless) error messages.
+ */
+UNUSUAL_DEV( 0xc251, 0x4003, 0x0100, 0x0100,
+ "Keil Software, Inc.",
+ "V2M MotherBoard",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_NOT_LOCKABLE),
+
/* Reported by Andrew Simmons <andrew.simmons@gmail.com> */
UNUSUAL_DEV( 0xed06, 0x4500, 0x0001, 0x0001,
"DataStor",
/* #define DEBUG */
-#ifdef DEBUG
-#define DPRINTK(fmt, args...) \
-do { \
- printk(KERN_DEBUG "pid %d: %s: " fmt "\n", \
- current->pid, __func__, ##args); \
-} while (0)
-#else
-#define DPRINTK(fmt, args...) do {} while (0)
-#endif
-
-#define AUTOFS_WARN(fmt, args...) \
-do { \
+#define DPRINTK(fmt, ...) \
+ pr_debug("pid %d: %s: " fmt "\n", \
+ current->pid, __func__, ##__VA_ARGS__)
+
+#define AUTOFS_WARN(fmt, ...) \
printk(KERN_WARNING "pid %d: %s: " fmt "\n", \
- current->pid, __func__, ##args); \
-} while (0)
+ current->pid, __func__, ##__VA_ARGS__)
-#define AUTOFS_ERROR(fmt, args...) \
-do { \
+#define AUTOFS_ERROR(fmt, ...) \
printk(KERN_ERR "pid %d: %s: " fmt "\n", \
- current->pid, __func__, ##args); \
-} while (0)
+ current->pid, __func__, ##__VA_ARGS__)
/* Unified info structure. This is pointed to by both the dentry and
inode structures. Each file in the filesystem has an instance of this
size_t pktsz;
DPRINTK("wait id = 0x%08lx, name = %.*s, type=%d",
- wq->wait_queue_token, wq->name.len, wq->name.name, type);
+ (unsigned long) wq->wait_queue_token, wq->name.len, wq->name.name, type);
memset(&pkt,0,sizeof pkt); /* For security reasons */
COMPATIBLE_IOCTL(PPPIOCDISCONN)
COMPATIBLE_IOCTL(PPPIOCATTCHAN)
COMPATIBLE_IOCTL(PPPIOCGCHAN)
+COMPATIBLE_IOCTL(PPPIOCGL2TPSTATS)
/* PPPOX */
COMPATIBLE_IOCTL(PPPOEIOCSFWD)
COMPATIBLE_IOCTL(PPPOEIOCDFWD)
config ECRYPT_FS
tristate "eCrypt filesystem layer support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && KEYS && CRYPTO
+ depends on EXPERIMENTAL && KEYS && CRYPTO && (ENCRYPTED_KEYS || ENCRYPTED_KEYS=n)
select CRYPTO_ECB
select CRYPTO_CBC
select CRYPTO_MD5
{
struct ecryptfs_msg_ctx *msg_ctx = NULL;
char *payload = NULL;
- size_t payload_len;
+ size_t payload_len = 0;
struct ecryptfs_message *msg;
int rc;
ecryptfs_opt_encrypted_view, ecryptfs_opt_fnek_sig,
ecryptfs_opt_fn_cipher, ecryptfs_opt_fn_cipher_key_bytes,
ecryptfs_opt_unlink_sigs, ecryptfs_opt_mount_auth_tok_only,
+ ecryptfs_opt_check_dev_ruid,
ecryptfs_opt_err };
static const match_table_t tokens = {
{ecryptfs_opt_fn_cipher_key_bytes, "ecryptfs_fn_key_bytes=%u"},
{ecryptfs_opt_unlink_sigs, "ecryptfs_unlink_sigs"},
{ecryptfs_opt_mount_auth_tok_only, "ecryptfs_mount_auth_tok_only"},
+ {ecryptfs_opt_check_dev_ruid, "ecryptfs_check_dev_ruid"},
{ecryptfs_opt_err, NULL}
};
* ecryptfs_parse_options
* @sb: The ecryptfs super block
* @options: The options passed to the kernel
+ * @check_ruid: set to 1 if device uid should be checked against the ruid
*
* Parse mount options:
* debug=N - ecryptfs_verbosity level for debug output
*
* Returns zero on success; non-zero on error
*/
-static int ecryptfs_parse_options(struct ecryptfs_sb_info *sbi, char *options)
+static int ecryptfs_parse_options(struct ecryptfs_sb_info *sbi, char *options,
+ uid_t *check_ruid)
{
char *p;
int rc = 0;
char *cipher_key_bytes_src;
char *fn_cipher_key_bytes_src;
+ *check_ruid = 0;
+
if (!options) {
rc = -EINVAL;
goto out;
mount_crypt_stat->flags |=
ECRYPTFS_GLOBAL_MOUNT_AUTH_TOK_ONLY;
break;
+ case ecryptfs_opt_check_dev_ruid:
+ *check_ruid = 1;
+ break;
case ecryptfs_opt_err:
default:
printk(KERN_WARNING
const char *err = "Getting sb failed";
struct inode *inode;
struct path path;
+ uid_t check_ruid;
int rc;
sbi = kmem_cache_zalloc(ecryptfs_sb_info_cache, GFP_KERNEL);
goto out;
}
- rc = ecryptfs_parse_options(sbi, raw_data);
+ rc = ecryptfs_parse_options(sbi, raw_data, &check_ruid);
if (rc) {
err = "Error parsing options";
goto out;
"known incompatibilities\n");
goto out_free;
}
+
+ if (check_ruid && path.dentry->d_inode->i_uid != current_uid()) {
+ rc = -EPERM;
+ printk(KERN_ERR "Mount of device (uid: %d) not owned by "
+ "requested user (uid: %d)\n",
+ path.dentry->d_inode->i_uid, current_uid());
+ goto out_free;
+ }
+
ecryptfs_set_superblock_lower(s, path.dentry->d_sb);
s->s_maxbytes = path.dentry->d_sb->s_maxbytes;
s->s_blocksize = path.dentry->d_sb->s_blocksize;
int ecryptfs_write_lower(struct inode *ecryptfs_inode, char *data,
loff_t offset, size_t size)
{
- struct ecryptfs_inode_info *inode_info;
+ struct file *lower_file;
mm_segment_t fs_save;
ssize_t rc;
- inode_info = ecryptfs_inode_to_private(ecryptfs_inode);
- BUG_ON(!inode_info->lower_file);
+ lower_file = ecryptfs_inode_to_private(ecryptfs_inode)->lower_file;
+ if (!lower_file)
+ return -EIO;
fs_save = get_fs();
set_fs(get_ds());
- rc = vfs_write(inode_info->lower_file, data, size, &offset);
+ rc = vfs_write(lower_file, data, size, &offset);
set_fs(fs_save);
mark_inode_dirty_sync(ecryptfs_inode);
return rc;
int ecryptfs_read_lower(char *data, loff_t offset, size_t size,
struct inode *ecryptfs_inode)
{
- struct ecryptfs_inode_info *inode_info =
- ecryptfs_inode_to_private(ecryptfs_inode);
+ struct file *lower_file;
mm_segment_t fs_save;
ssize_t rc;
- BUG_ON(!inode_info->lower_file);
+ lower_file = ecryptfs_inode_to_private(ecryptfs_inode)->lower_file;
+ if (!lower_file)
+ return -EIO;
fs_save = get_fs();
set_fs(get_ds());
- rc = vfs_read(inode_info->lower_file, data, size, &offset);
+ rc = vfs_read(lower_file, data, size, &offset);
set_fs(fs_save);
return rc;
}
struct files_struct *displaced;
bool clear_in_exec;
int retval;
+ const struct cred *cred = current_cred();
+
+ /*
+ * We move the actual failure in case of RLIMIT_NPROC excess from
+ * set*uid() to execve() because too many poorly written programs
+ * don't check setuid() return code. Here we additionally recheck
+ * whether NPROC limit is still exceeded.
+ */
+ if ((current->flags & PF_NPROC_EXCEEDED) &&
+ atomic_read(&cred->user->processes) > rlimit(RLIMIT_NPROC)) {
+ retval = -EAGAIN;
+ goto out_ret;
+ }
+
+ /* We're below the limit (still or again), so we don't want to make
+ * further execve() calls fail. */
+ current->flags &= ~PF_NPROC_EXCEEDED;
retval = unshare_files(&displaced);
if (retval)
/*
* For non-fast symlinks, we just allocate inode and put it on
* orphan list in the first transaction => we need bitmap,
- * group descriptor, sb, inode block, quota blocks.
+ * group descriptor, sb, inode block, quota blocks, and
+ * possibly selinux xattr blocks.
*/
- credits = 4 + EXT3_MAXQUOTAS_INIT_BLOCKS(dir->i_sb);
+ credits = 4 + EXT3_MAXQUOTAS_INIT_BLOCKS(dir->i_sb) +
+ EXT3_XATTR_TRANS_BLOCKS;
} else {
/*
* Fast symlink. We have to add entry to directory
/*
* For non-fast symlinks, we just allocate inode and put it on
* orphan list in the first transaction => we need bitmap,
- * group descriptor, sb, inode block, quota blocks.
+ * group descriptor, sb, inode block, quota blocks, and
+ * possibly selinux xattr blocks.
*/
- credits = 4 + EXT4_MAXQUOTAS_INIT_BLOCKS(dir->i_sb);
+ credits = 4 + EXT4_MAXQUOTAS_INIT_BLOCKS(dir->i_sb) +
+ EXT4_XATTR_TRANS_BLOCKS;
} else {
/*
* Fast symlink. We have to add entry to directory
depends on NFS_FS && NFS_V4 && EXPERIMENTAL
select SUNRPC_BACKCHANNEL
select PNFS_FILE_LAYOUT
- select PNFS_BLOCK
- select MD
- select BLK_DEV_DM
help
This option enables support for minor version 1 of the NFSv4 protocol
- (RFC 5661 and RFC 5663) in the kernel's NFS client.
+ (RFC 5661) in the kernel's NFS client.
If unsure, say N.
config PNFS_BLOCK
tristate
+ depends on NFS_FS && NFS_V4_1 && BLK_DEV_DM
+ default m
config PNFS_OBJLAYOUT
- tristate "Provide support for the pNFS Objects Layout Driver for NFSv4.1 pNFS (EXPERIMENTAL)"
+ tristate
depends on NFS_FS && NFS_V4_1 && SCSI_OSD_ULD
- help
- Say M here if you want your pNFS client to support the Objects Layout Driver.
- Requires the SCSI osd initiator library (SCSI_OSD_INITIATOR) and
- upper level driver (SCSI_OSD_ULD).
-
- If unsure, say N.
+ default m
config ROOT_NFS
bool "Root file system on NFS"
bp->b_flags |= flags & (XBF_READ | XBF_ASYNC | XBF_READ_AHEAD);
status = xfs_buf_iorequest(bp);
- if (status || XFS_BUF_ISERROR(bp) || (flags & XBF_ASYNC))
+ if (status || bp->b_error || (flags & XBF_ASYNC))
return status;
return xfs_buf_iowait(bp);
}
/* set up the buffer for a read IO */
XFS_BUF_SET_ADDR(bp, daddr);
XFS_BUF_READ(bp);
- XFS_BUF_BUSY(bp);
xfsbdstrat(mp, bp);
error = xfs_buf_iowait(bp);
/*
* No need to wait until the buffer is unpinned, we aren't flushing it.
*/
- XFS_BUF_ERROR(bp, EIO);
+ xfs_buf_ioerror(bp, EIO);
/*
* We're calling xfs_buf_ioend, so delete XBF_DONE flag.
xfs_bioerror_relse(
struct xfs_buf *bp)
{
- int64_t fl = XFS_BUF_BFLAGS(bp);
+ int64_t fl = bp->b_flags;
/*
* No need to wait until the buffer is unpinned.
* We aren't flushing it.
* There's no reason to mark error for
* ASYNC buffers.
*/
- XFS_BUF_ERROR(bp, EIO);
+ xfs_buf_ioerror(bp, EIO);
XFS_BUF_FINISH_IOWAIT(bp);
} else {
xfs_buf_relse(bp);
struct page *page;
if (bp->b_flags & XBF_MAPPED)
- return XFS_BUF_PTR(bp) + offset;
+ return bp->b_addr + offset;
offset += bp->b_offset;
page = bp->b_pages[offset >> PAGE_SHIFT];
if (set_blocksize(btp->bt_bdev, sectorsize)) {
xfs_warn(btp->bt_mount,
"Cannot set_blocksize to %u on device %s\n",
- sectorsize, XFS_BUFTARG_NAME(btp));
+ sectorsize, xfs_buf_target_name(btp));
return EINVAL;
}
list_for_each_entry_safe(bp, n, dwq, b_list) {
ASSERT(bp->b_flags & XBF_DELWRI);
- if (!XFS_BUF_ISPINNED(bp) && xfs_buf_trylock(bp)) {
+ if (!xfs_buf_ispinned(bp) && xfs_buf_trylock(bp)) {
if (!force &&
time_before(jiffies, bp->b_queuetime + age)) {
xfs_buf_unlock(bp);
extern int xfs_buf_init(void);
extern void xfs_buf_terminate(void);
-#define xfs_buf_target_name(target) \
- ({ char __b[BDEVNAME_SIZE]; bdevname((target)->bt_bdev, __b); __b; })
+static inline const char *
+xfs_buf_target_name(struct xfs_buftarg *target)
+{
+ static char __b[BDEVNAME_SIZE];
+
+ return bdevname(target->bt_bdev, __b);
+}
-#define XFS_BUF_BFLAGS(bp) ((bp)->b_flags)
#define XFS_BUF_ZEROFLAGS(bp) \
((bp)->b_flags &= ~(XBF_READ|XBF_WRITE|XBF_ASYNC|XBF_DELWRI| \
XBF_SYNCIO|XBF_FUA|XBF_FLUSH))
#define XFS_BUF_UNDELAYWRITE(bp) xfs_buf_delwri_dequeue(bp)
#define XFS_BUF_ISDELAYWRITE(bp) ((bp)->b_flags & XBF_DELWRI)
-#define XFS_BUF_ERROR(bp,no) xfs_buf_ioerror(bp,no)
-#define XFS_BUF_GETERROR(bp) xfs_buf_geterror(bp)
-#define XFS_BUF_ISERROR(bp) (xfs_buf_geterror(bp) ? 1 : 0)
-
#define XFS_BUF_DONE(bp) ((bp)->b_flags |= XBF_DONE)
#define XFS_BUF_UNDONE(bp) ((bp)->b_flags &= ~XBF_DONE)
#define XFS_BUF_ISDONE(bp) ((bp)->b_flags & XBF_DONE)
-#define XFS_BUF_BUSY(bp) do { } while (0)
-#define XFS_BUF_UNBUSY(bp) do { } while (0)
-#define XFS_BUF_ISBUSY(bp) (1)
-
#define XFS_BUF_ASYNC(bp) ((bp)->b_flags |= XBF_ASYNC)
#define XFS_BUF_UNASYNC(bp) ((bp)->b_flags &= ~XBF_ASYNC)
#define XFS_BUF_ISASYNC(bp) ((bp)->b_flags & XBF_ASYNC)
-#define XFS_BUF_HOLD(bp) xfs_buf_hold(bp)
#define XFS_BUF_READ(bp) ((bp)->b_flags |= XBF_READ)
#define XFS_BUF_UNREAD(bp) ((bp)->b_flags &= ~XBF_READ)
#define XFS_BUF_ISREAD(bp) ((bp)->b_flags & XBF_READ)
#define XFS_BUF_UNWRITE(bp) ((bp)->b_flags &= ~XBF_WRITE)
#define XFS_BUF_ISWRITE(bp) ((bp)->b_flags & XBF_WRITE)
-#define XFS_BUF_SET_START(bp) do { } while (0)
-
-#define XFS_BUF_PTR(bp) (xfs_caddr_t)((bp)->b_addr)
-#define XFS_BUF_SET_PTR(bp, val, cnt) xfs_buf_associate_memory(bp, val, cnt)
#define XFS_BUF_ADDR(bp) ((bp)->b_bn)
#define XFS_BUF_SET_ADDR(bp, bno) ((bp)->b_bn = (xfs_daddr_t)(bno))
#define XFS_BUF_OFFSET(bp) ((bp)->b_file_offset)
#define XFS_BUF_SET_VTYPE_REF(bp, type, ref) xfs_buf_set_ref(bp, ref)
#define XFS_BUF_SET_VTYPE(bp, type) do { } while (0)
-#define XFS_BUF_ISPINNED(bp) atomic_read(&((bp)->b_pin_count))
+static inline int xfs_buf_ispinned(struct xfs_buf *bp)
+{
+ return atomic_read(&bp->b_pin_count);
+}
#define XFS_BUF_FINISH_IOWAIT(bp) complete(&bp->b_iowait);
-#define XFS_BUF_SET_TARGET(bp, target) ((bp)->b_target = (target))
-#define XFS_BUF_TARGET(bp) ((bp)->b_target)
-#define XFS_BUFTARG_NAME(target) xfs_buf_target_name(target)
-
static inline void xfs_buf_relse(xfs_buf_t *bp)
{
xfs_buf_unlock(bp);
* between there and here.
*/
bp = xfs_getsb(mp, 0);
- if (XFS_BUF_ISPINNED(bp))
+ if (xfs_buf_ispinned(bp))
xfs_log_force(mp, 0);
return xfs_bwrite(mp, bp);
int curid, i;
ASSERT(tp);
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(xfs_buf_islocked(bp));
- d = (xfs_dqblk_t *)XFS_BUF_PTR(bp);
+ d = bp->b_addr;
/*
* ID of the first dquot in the block - id's are zero based.
dqp->q_blkno,
mp->m_quotainfo->qi_dqchunklen,
0);
- if (!bp || (error = XFS_BUF_GETERROR(bp)))
+ if (!bp || (error = xfs_buf_geterror(bp)))
goto error1;
/*
* Make a chunk of dquots out of this buffer and log
return XFS_ERROR(error);
}
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(xfs_buf_islocked(bp));
/*
* calculate the location of the dquot inside the buffer.
*/
- ddq = (struct xfs_disk_dquot *)(XFS_BUF_PTR(bp) + dqp->q_bufoffset);
+ ddq = bp->b_addr + dqp->q_bufoffset;
/*
* A simple sanity check in case we got a corrupted dquot...
xfs_trans_brelse(tp, bp);
return XFS_ERROR(EIO);
}
- XFS_BUF_BUSY(bp); /* We dirtied this */
}
*O_bpp = bp;
* this particular dquot was repaired. We still aren't afraid to
* brelse it because we have the changes incore.
*/
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(xfs_buf_islocked(bp));
xfs_trans_brelse(tp, bp);
/*
* Calculate the location of the dquot inside the buffer.
*/
- ddqp = (struct xfs_disk_dquot *)(XFS_BUF_PTR(bp) + dqp->q_bufoffset);
+ ddqp = bp->b_addr + dqp->q_bufoffset;
/*
* A simple sanity check in case we got a corrupted dquot..
* If the buffer is pinned then push on the log so we won't
* get stuck waiting in the write for too long.
*/
- if (XFS_BUF_ISPINNED(bp)) {
+ if (xfs_buf_ispinned(bp)) {
trace_xfs_dqflush_force(dqp);
xfs_log_force(mp, 0);
}
goto out_lock;
if (XFS_BUF_ISDELAYWRITE(bp)) {
- if (XFS_BUF_ISPINNED(bp))
+ if (xfs_buf_ispinned(bp))
xfs_log_force(mp, 0);
xfs_buf_delwri_promote(bp);
wake_up_process(bp->b_target->bt_task);
do_div(j, sizeof(xfs_dqblk_t));
ASSERT(mp->m_quotainfo->qi_dqperchunk == j);
#endif
- ddq = (xfs_disk_dquot_t *)XFS_BUF_PTR(bp);
+ ddq = bp->b_addr;
for (j = 0; j < mp->m_quotainfo->qi_dqperchunk; j++) {
/*
* Do a sanity check, and if needed, repair the dqblk. Don't
/* disk block (xfs_daddr_t) in the AG */
#define XFS_AGF_DADDR(mp) ((xfs_daddr_t)(1 << (mp)->m_sectbb_log))
#define XFS_AGF_BLOCK(mp) XFS_HDR_BLOCK(mp, XFS_AGF_DADDR(mp))
-#define XFS_BUF_TO_AGF(bp) ((xfs_agf_t *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_AGF(bp) ((xfs_agf_t *)((bp)->b_addr))
extern int xfs_read_agf(struct xfs_mount *mp, struct xfs_trans *tp,
xfs_agnumber_t agno, int flags, struct xfs_buf **bpp);
/* disk block (xfs_daddr_t) in the AG */
#define XFS_AGI_DADDR(mp) ((xfs_daddr_t)(2 << (mp)->m_sectbb_log))
#define XFS_AGI_BLOCK(mp) XFS_HDR_BLOCK(mp, XFS_AGI_DADDR(mp))
-#define XFS_BUF_TO_AGI(bp) ((xfs_agi_t *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_AGI(bp) ((xfs_agi_t *)((bp)->b_addr))
extern int xfs_read_agi(struct xfs_mount *mp, struct xfs_trans *tp,
xfs_agnumber_t agno, struct xfs_buf **bpp);
#define XFS_AGFL_DADDR(mp) ((xfs_daddr_t)(3 << (mp)->m_sectbb_log))
#define XFS_AGFL_BLOCK(mp) XFS_HDR_BLOCK(mp, XFS_AGFL_DADDR(mp))
#define XFS_AGFL_SIZE(mp) ((mp)->m_sb.sb_sectsize / sizeof(xfs_agblock_t))
-#define XFS_BUF_TO_AGFL(bp) ((xfs_agfl_t *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_AGFL(bp) ((xfs_agfl_t *)((bp)->b_addr))
typedef struct xfs_agfl {
__be32 agfl_bno[1]; /* actually XFS_AGFL_SIZE(mp) */
XFS_FSS_TO_BB(mp, 1), 0, &bp);
if (error)
return error;
- ASSERT(bp);
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
XFS_BUF_SET_VTYPE_REF(bp, B_FS_AGFL, XFS_AGFL_REF);
*bpp = bp;
return 0;
if (!*bpp)
return 0;
- ASSERT(!XFS_BUF_GETERROR(*bpp));
+ ASSERT(!(*bpp)->b_error);
agf = XFS_BUF_TO_AGF(*bpp);
/*
return error;
if (!*bpp)
return 0;
- ASSERT(!XFS_BUF_GETERROR(*bpp));
+ ASSERT(!(*bpp)->b_error);
agf = XFS_BUF_TO_AGF(*bpp);
pag = xfs_perag_get(mp, agno);
bp = xfs_buf_get(mp->m_ddev_targp, dblkno, blkcnt,
XBF_LOCK | XBF_DONT_BLOCK);
- ASSERT(bp);
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
tmp = (valuelen < XFS_BUF_SIZE(bp)) ? valuelen :
XFS_BUF_SIZE(bp);
ASSERT(args.len == 1);
*firstblock = args.fsbno;
bp = xfs_btree_get_bufl(args.mp, tp, args.fsbno, 0);
- memcpy((char *)XFS_BUF_PTR(bp), ifp->if_u1.if_data,
- ifp->if_bytes);
+ memcpy(bp->b_addr, ifp->if_u1.if_data, ifp->if_bytes);
xfs_trans_log_buf(tp, bp, 0, ifp->if_bytes - 1);
xfs_bmap_forkoff_reset(args.mp, ip, whichfork);
xfs_idata_realloc(ip, -ifp->if_bytes, whichfork);
return error;
}
new->bc_bufs[i] = bp;
- ASSERT(bp);
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
} else
new->bc_bufs[i] = NULL;
}
ASSERT(fsbno != NULLFSBLOCK);
d = XFS_FSB_TO_DADDR(mp, fsbno);
bp = xfs_trans_get_buf(tp, mp->m_ddev_targp, d, mp->m_bsize, lock);
- ASSERT(bp);
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
return bp;
}
ASSERT(agbno != NULLAGBLOCK);
d = XFS_AGB_TO_DADDR(mp, agno, agbno);
bp = xfs_trans_get_buf(tp, mp->m_ddev_targp, d, mp->m_bsize, lock);
- ASSERT(bp);
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
return bp;
}
mp->m_bsize, lock, &bp))) {
return error;
}
- ASSERT(!bp || !XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
if (bp)
XFS_BUF_SET_VTYPE_REF(bp, B_FS_MAP, refval);
*bpp = bp;
*bpp = xfs_trans_get_buf(cur->bc_tp, mp->m_ddev_targp, d,
mp->m_bsize, flags);
- ASSERT(*bpp);
- ASSERT(!XFS_BUF_GETERROR(*bpp));
+ ASSERT(!xfs_buf_geterror(*bpp));
*block = XFS_BUF_TO_BLOCK(*bpp);
return 0;
if (error)
return error;
- ASSERT(*bpp != NULL);
- ASSERT(!XFS_BUF_GETERROR(*bpp));
+ ASSERT(!xfs_buf_geterror(*bpp));
xfs_btree_set_refs(cur, *bpp);
*block = XFS_BUF_TO_BLOCK(*bpp);
/*
* Convert from buffer to btree block header.
*/
-#define XFS_BUF_TO_BLOCK(bp) ((struct xfs_btree_block *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_BLOCK(bp) ((struct xfs_btree_block *)((bp)->b_addr))
/*
bp = bip->bli_buf;
ASSERT(XFS_BUF_COUNT(bp) > 0);
- ASSERT(XFS_BUF_PTR(bp) != NULL);
+ ASSERT(bp->b_addr != NULL);
orig = bip->bli_orig;
- buffer = XFS_BUF_PTR(bp);
+ buffer = bp->b_addr;
for (x = 0; x < XFS_BUF_COUNT(bp); x++) {
if (orig[x] != buffer[x] && !btst(bip->bli_logged, x)) {
xfs_emerg(bp->b_mount,
{
struct xfs_buf_log_item *bip = BUF_ITEM(lip);
- ASSERT(XFS_BUF_ISBUSY(bip->bli_buf));
ASSERT(atomic_read(&bip->bli_refcount) > 0);
ASSERT((bip->bli_flags & XFS_BLI_LOGGED) ||
(bip->bli_flags & XFS_BLI_STALE));
struct xfs_buf_log_item *bip = BUF_ITEM(lip);
struct xfs_buf *bp = bip->bli_buf;
- if (XFS_BUF_ISPINNED(bp))
+ if (xfs_buf_ispinned(bp))
return XFS_ITEM_PINNED;
if (!xfs_buf_trylock(bp))
return XFS_ITEM_LOCKED;
/* take a reference to the buffer. */
- XFS_BUF_HOLD(bp);
+ xfs_buf_hold(bp);
ASSERT(!(bip->bli_flags & XFS_BLI_STALE));
trace_xfs_buf_item_trylock(bip);
* to have logged.
*/
bip->bli_orig = (char *)kmem_alloc(XFS_BUF_COUNT(bp), KM_SLEEP);
- memcpy(bip->bli_orig, XFS_BUF_PTR(bp), XFS_BUF_COUNT(bp));
+ memcpy(bip->bli_orig, bp->b_addr, XFS_BUF_COUNT(bp));
bip->bli_logged = (char *)kmem_zalloc(XFS_BUF_COUNT(bp) / NBBY, KM_SLEEP);
#endif
{
xfs_log_item_t *head_lip;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(xfs_buf_islocked(bp));
lip->li_cb = cb;
static ulong lasttime;
static xfs_buftarg_t *lasttarg;
- if (likely(!XFS_BUF_GETERROR(bp)))
+ if (likely(!xfs_buf_geterror(bp)))
goto do_callbacks;
/*
goto do_callbacks;
}
- if (XFS_BUF_TARGET(bp) != lasttarg ||
+ if (bp->b_target != lasttarg ||
time_after(jiffies, (lasttime + 5*HZ))) {
lasttime = jiffies;
xfs_alert(mp, "Device %s: metadata write error block 0x%llx",
- XFS_BUFTARG_NAME(XFS_BUF_TARGET(bp)),
+ xfs_buf_target_name(bp->b_target),
(__uint64_t)XFS_BUF_ADDR(bp));
}
- lasttarg = XFS_BUF_TARGET(bp);
+ lasttarg = bp->b_target;
/*
* If the write was asynchronous then no one will be looking for the
* around.
*/
if (XFS_BUF_ISASYNC(bp)) {
- XFS_BUF_ERROR(bp, 0); /* errno of 0 unsets the flag */
+ xfs_buf_ioerror(bp, 0); /* errno of 0 unsets the flag */
if (!XFS_BUF_ISSTALE(bp)) {
XFS_BUF_DELAYWRITE(bp);
XFS_BUF_DONE(bp);
- XFS_BUF_SET_START(bp);
}
ASSERT(bp->b_iodone != NULL);
trace_xfs_buf_item_iodone_async(bp, _RET_IP_);
XFS_BUF_UNDELAYWRITE(bp);
trace_xfs_buf_error_relse(bp, _RET_IP_);
- xfs_force_shutdown(mp, SHUTDOWN_META_IO_ERROR);
do_callbacks:
xfs_buf_do_callbacks(bp);
case 0:
bp = xfs_trans_get_buf(trans, mp->m_ddev_targp,
mappedbno, nmapped, 0);
- error = bp ? XFS_BUF_GETERROR(bp) : XFS_ERROR(EIO);
+ error = bp ? bp->b_error : XFS_ERROR(EIO);
break;
case 1:
case 2:
dabuf->nbuf = 1;
bp = bps[0];
dabuf->bbcount = (short)BTOBB(XFS_BUF_COUNT(bp));
- dabuf->data = XFS_BUF_PTR(bp);
+ dabuf->data = bp->b_addr;
dabuf->bps[0] = bp;
} else {
dabuf->nbuf = nbuf;
dabuf->data = kmem_alloc(BBTOB(dabuf->bbcount), KM_SLEEP);
for (i = off = 0; i < nbuf; i++, off += XFS_BUF_COUNT(bp)) {
bp = bps[i];
- memcpy((char *)dabuf->data + off, XFS_BUF_PTR(bp),
+ memcpy((char *)dabuf->data + off, bp->b_addr,
XFS_BUF_COUNT(bp));
}
}
for (i = off = 0; i < dabuf->nbuf;
i++, off += XFS_BUF_COUNT(bp)) {
bp = dabuf->bps[i];
- memcpy(XFS_BUF_PTR(bp), (char *)dabuf->data + off,
- XFS_BUF_COUNT(bp));
+ memcpy(bp->b_addr, dabuf->data + off,
+ XFS_BUF_COUNT(bp));
}
}
}
ASSERT(dabuf->nbuf && dabuf->data && dabuf->bbcount && dabuf->bps[0]);
if (dabuf->nbuf == 1) {
- ASSERT(dabuf->data == (void *)XFS_BUF_PTR(dabuf->bps[0]));
+ ASSERT(dabuf->data == dabuf->bps[0]->b_addr);
xfs_trans_log_buf(tp, dabuf->bps[0], first, last);
return;
}
be32_to_cpu((dip)->di_nextents) : \
be16_to_cpu((dip)->di_anextents))
-#define XFS_BUF_TO_DINODE(bp) ((xfs_dinode_t *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_DINODE(bp) ((xfs_dinode_t *)((bp)->b_addr))
/*
* For block and character special files the 32bit dev_t is stored at the
fbuf = xfs_trans_get_buf(tp, mp->m_ddev_targp, d,
mp->m_bsize * blks_per_cluster,
XBF_LOCK);
- ASSERT(fbuf);
- ASSERT(!XFS_BUF_GETERROR(fbuf));
+ ASSERT(!xfs_buf_geterror(fbuf));
/*
* Initialize all inodes in this buffer and then log them.
if (error)
return error;
- ASSERT(*bpp && !XFS_BUF_GETERROR(*bpp));
+ ASSERT(!xfs_buf_geterror(*bpp));
agi = XFS_BUF_TO_AGI(*bpp);
/*
if (bp->b_iodone) {
XFS_BUF_UNDONE(bp);
XFS_BUF_STALE(bp);
- XFS_BUF_ERROR(bp,EIO);
+ xfs_buf_ioerror(bp, EIO);
xfs_buf_ioend(bp, 0);
} else {
XFS_BUF_STALE(bp);
* If the buffer is pinned then push on the log now so we won't
* get stuck waiting in the write for too long.
*/
- if (XFS_BUF_ISPINNED(bp))
+ if (xfs_buf_ispinned(bp))
xfs_log_force(mp, 0);
/*
/*
* Race to shutdown the filesystem if we see an error.
*/
- if (XFS_TEST_ERROR((XFS_BUF_GETERROR(bp)), l->l_mp,
+ if (XFS_TEST_ERROR((xfs_buf_geterror(bp)), l->l_mp,
XFS_ERRTAG_IODONE_IOERR, XFS_RANDOM_IODONE_IOERR)) {
xfs_ioerror_alert("xlog_iodone", l->l_mp, bp, XFS_BUF_ADDR(bp));
XFS_BUF_STALE(bp);
if (!bp)
goto out_free_log;
bp->b_iodone = xlog_iodone;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(xfs_buf_islocked(bp));
log->l_xbuf = bp;
iclog->ic_callback_tail = &(iclog->ic_callback);
iclog->ic_datap = (char *)iclog->ic_data + log->l_iclog_hsize;
- ASSERT(XFS_BUF_ISBUSY(iclog->ic_bp));
ASSERT(xfs_buf_islocked(iclog->ic_bp));
init_waitqueue_head(&iclog->ic_force_wait);
init_waitqueue_head(&iclog->ic_write_wait);
struct xlog_in_core *iclog = bp->b_fspriv;
if (iclog->ic_state & XLOG_STATE_IOERROR) {
- XFS_BUF_ERROR(bp, EIO);
+ xfs_buf_ioerror(bp, EIO);
XFS_BUF_STALE(bp);
xfs_buf_ioend(bp, 0);
/*
XFS_BUF_SET_COUNT(bp, count);
bp->b_fspriv = iclog;
XFS_BUF_ZEROFLAGS(bp);
- XFS_BUF_BUSY(bp);
XFS_BUF_ASYNC(bp);
bp->b_flags |= XBF_SYNCIO;
if (split) {
bp = iclog->ic_log->l_xbuf;
XFS_BUF_SET_ADDR(bp, 0); /* logical 0 */
- XFS_BUF_SET_PTR(bp, (xfs_caddr_t)((__psint_t)&(iclog->ic_header)+
- (__psint_t)count), split);
+ xfs_buf_associate_memory(bp,
+ (char *)&iclog->ic_header + count, split);
bp->b_fspriv = iclog;
XFS_BUF_ZEROFLAGS(bp);
- XFS_BUF_BUSY(bp);
XFS_BUF_ASYNC(bp);
bp->b_flags |= XBF_SYNCIO;
if (log->l_mp->m_flags & XFS_MOUNT_BARRIER)
bp->b_flags |= XBF_FUA;
- dptr = XFS_BUF_PTR(bp);
+ dptr = bp->b_addr;
/*
* Bump the cycle numbers at the start of each block
* since this part of the buffer is at the start of
xfs_daddr_t offset = blk_no & ((xfs_daddr_t)log->l_sectBBsize - 1);
ASSERT(BBTOB(offset + nbblks) <= XFS_BUF_SIZE(bp));
- return XFS_BUF_PTR(bp) + BBTOB(offset);
+ return bp->b_addr + BBTOB(offset);
}
XFS_BUF_SET_ADDR(bp, log->l_logBBstart + blk_no);
XFS_BUF_READ(bp);
- XFS_BUF_BUSY(bp);
XFS_BUF_SET_COUNT(bp, BBTOB(nbblks));
- XFS_BUF_SET_TARGET(bp, log->l_mp->m_logdev_targp);
xfsbdstrat(log->l_mp, bp);
error = xfs_buf_iowait(bp);
xfs_buf_t *bp,
xfs_caddr_t offset)
{
- xfs_caddr_t orig_offset = XFS_BUF_PTR(bp);
+ xfs_caddr_t orig_offset = bp->b_addr;
int orig_len = bp->b_buffer_length;
int error, error2;
- error = XFS_BUF_SET_PTR(bp, offset, BBTOB(nbblks));
+ error = xfs_buf_associate_memory(bp, offset, BBTOB(nbblks));
if (error)
return error;
error = xlog_bread_noalign(log, blk_no, nbblks, bp);
/* must reset buffer pointer even on error */
- error2 = XFS_BUF_SET_PTR(bp, orig_offset, orig_len);
+ error2 = xfs_buf_associate_memory(bp, orig_offset, orig_len);
if (error)
return error;
return error2;
XFS_BUF_SET_ADDR(bp, log->l_logBBstart + blk_no);
XFS_BUF_ZEROFLAGS(bp);
- XFS_BUF_BUSY(bp);
- XFS_BUF_HOLD(bp);
+ xfs_buf_hold(bp);
xfs_buf_lock(bp);
XFS_BUF_SET_COUNT(bp, BBTOB(nbblks));
- XFS_BUF_SET_TARGET(bp, log->l_mp->m_logdev_targp);
if ((error = xfs_bwrite(log->l_mp, bp)))
xfs_ioerror_alert("xlog_bwrite", log->l_mp,
xlog_recover_iodone(
struct xfs_buf *bp)
{
- if (XFS_BUF_GETERROR(bp)) {
+ if (bp->b_error) {
/*
* We're not going to bother about retrying
* this during recovery. One strike!
*/
ealign = round_down(end_block, sectbb);
if (j == 0 && (start_block + endcount > ealign)) {
- offset = XFS_BUF_PTR(bp) + BBTOB(ealign - start_block);
+ offset = bp->b_addr + BBTOB(ealign - start_block);
error = xlog_bread_offset(log, ealign, sectbb,
bp, offset);
if (error)
bp = xfs_buf_read(mp->m_ddev_targp, buf_f->blf_blkno, buf_f->blf_len,
buf_flags);
- if (XFS_BUF_ISERROR(bp)) {
+ if (!bp)
+ return XFS_ERROR(ENOMEM);
+ error = bp->b_error;
+ if (error) {
xfs_ioerror_alert("xlog_recover_do..(read#1)", mp,
bp, buf_f->blf_blkno);
- error = XFS_BUF_GETERROR(bp);
xfs_buf_relse(bp);
return error;
}
- error = 0;
if (buf_f->blf_flags & XFS_BLF_INODE_BUF) {
error = xlog_recover_do_inode_buffer(mp, item, bp, buf_f);
} else if (buf_f->blf_flags &
bp = xfs_buf_read(mp->m_ddev_targp, in_f->ilf_blkno, in_f->ilf_len,
XBF_LOCK);
- if (XFS_BUF_ISERROR(bp)) {
+ if (!bp) {
+ error = ENOMEM;
+ goto error;
+ }
+ error = bp->b_error;
+ if (error) {
xfs_ioerror_alert("xlog_recover_do..(read#2)", mp,
bp, in_f->ilf_blkno);
- error = XFS_BUF_GETERROR(bp);
xfs_buf_relse(bp);
goto error;
}
- error = 0;
ASSERT(in_f->ilf_fields & XFS_ILOG_CORE);
dip = (xfs_dinode_t *)xfs_buf_offset(bp, in_f->ilf_boffset);
/*
* Check for header wrapping around physical end-of-log
*/
- offset = XFS_BUF_PTR(hbp);
+ offset = hbp->b_addr;
split_hblks = 0;
wrapped_hblks = 0;
if (blk_no + hblks <= log->l_logBBsize) {
} else {
/* This log record is split across the
* physical end of log */
- offset = XFS_BUF_PTR(dbp);
+ offset = dbp->b_addr;
split_bblks = 0;
if (blk_no != log->l_logBBsize) {
/* some data is before the physical
XFS_BUF_UNDELAYWRITE(sbp);
XFS_BUF_WRITE(sbp);
XFS_BUF_UNASYNC(sbp);
- ASSERT(XFS_BUF_TARGET(sbp) == mp->m_ddev_targp);
+ ASSERT(sbp->b_target == mp->m_ddev_targp);
xfsbdstrat(mp, sbp);
error = xfs_buf_iowait(sbp);
if (error)
xfs_buf_lock(bp);
}
- XFS_BUF_HOLD(bp);
+ xfs_buf_hold(bp);
ASSERT(XFS_BUF_ISDONE(bp));
return bp;
}
xfs_trans_cancel(tp, cancelflags);
goto error;
}
- memset(XFS_BUF_PTR(bp), 0, mp->m_sb.sb_blocksize);
+ memset(bp->b_addr, 0, mp->m_sb.sb_blocksize);
xfs_trans_log_buf(tp, bp, 0, mp->m_sb.sb_blocksize - 1);
/*
* Commit the transaction.
if (error) {
return error;
}
- ASSERT(bp && !XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
*bpp = bp;
return 0;
}
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
/*
* Compute the starting word's address, and starting bit.
*/
if (error) {
return error;
}
- b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ b = bufp = bp->b_addr;
word = 0;
} else {
/*
if (error) {
return error;
}
- b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ b = bufp = bp->b_addr;
word = 0;
} else {
/*
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
/*
* Get the first word's index & point to it.
*/
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
word = XFS_BLOCKWMASK(mp);
b = &bufp[word];
} else {
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
word = XFS_BLOCKWMASK(mp);
b = &bufp[word];
} else {
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
/*
* Get the first word's index & point to it.
*/
if (error) {
return error;
}
- b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ b = bufp = bp->b_addr;
word = 0;
} else {
/*
if (error) {
return error;
}
- b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ b = bufp = bp->b_addr;
word = 0;
} else {
/*
if (error) {
return error;
}
- bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ bufp = bp->b_addr;
/*
* Compute the starting word's address, and starting bit.
*/
if (error) {
return error;
}
- first = b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ first = b = bufp = bp->b_addr;
word = 0;
} else {
/*
if (error) {
return error;
}
- first = b = bufp = (xfs_rtword_t *)XFS_BUF_PTR(bp);
+ first = b = bufp = bp->b_addr;
word = 0;
} else {
/*
*/
sp = XFS_SUMPTR(mp, bp, so);
*sp += delta;
- xfs_trans_log_buf(tp, bp, (uint)((char *)sp - (char *)XFS_BUF_PTR(bp)),
- (uint)((char *)sp - (char *)XFS_BUF_PTR(bp) + sizeof(*sp) - 1));
+ xfs_trans_log_buf(tp, bp, (uint)((char *)sp - (char *)bp->b_addr),
+ (uint)((char *)sp - (char *)bp->b_addr + sizeof(*sp) - 1));
return 0;
}
#define XFS_SUMOFFSTOBLOCK(mp,s) \
(((s) * (uint)sizeof(xfs_suminfo_t)) >> (mp)->m_sb.sb_blocklog)
#define XFS_SUMPTR(mp,bp,so) \
- ((xfs_suminfo_t *)((char *)XFS_BUF_PTR(bp) + \
+ ((xfs_suminfo_t *)((bp)->b_addr + \
(((so) * (uint)sizeof(xfs_suminfo_t)) & XFS_BLOCKMASK(mp))))
#define XFS_BITTOBLOCK(mp,bi) ((bi) >> (mp)->m_blkbit_log)
xfs_alert(mp,
"I/O error occurred: meta-data dev %s block 0x%llx"
" (\"%s\") error %d buf count %zd",
- XFS_BUFTARG_NAME(XFS_BUF_TARGET(bp)),
+ xfs_buf_target_name(bp->b_target),
(__uint64_t)blkno, func,
- XFS_BUF_GETERROR(bp), XFS_BUF_COUNT(bp));
+ bp->b_error, XFS_BUF_COUNT(bp));
}
/*
bp = xfs_buf_read(target, blkno, len, flags);
if (!bp)
return XFS_ERROR(EIO);
- error = XFS_BUF_GETERROR(bp);
- if (bp && !error && !XFS_FORCED_SHUTDOWN(mp)) {
+ error = bp->b_error;
+ if (!error && !XFS_FORCED_SHUTDOWN(mp)) {
*bpp = bp;
} else {
*bpp = NULL;
#define XFS_SB_DADDR ((xfs_daddr_t)0) /* daddr in filesystem/ag */
#define XFS_SB_BLOCK(mp) XFS_HDR_BLOCK(mp, XFS_SB_DADDR)
-#define XFS_BUF_TO_SBP(bp) ((xfs_dsb_t *)XFS_BUF_PTR(bp))
+#define XFS_BUF_TO_SBP(bp) ((xfs_dsb_t *)((bp)->b_addr))
#define XFS_HDR_BLOCK(mp,d) ((xfs_agblock_t)XFS_BB_TO_FSBT(mp,d))
#define XFS_DADDR_TO_FSB(mp,d) XFS_AGB_TO_FSB(mp, \
* Splice the log item list into the AIL at the given LSN. We splice to the
* tail of the given LSN to maintain insert order for push traversals. The
* cursor is optional, allowing repeated updates to the same LSN to avoid
- * repeated traversals.
+ * repeated traversals. This should not be called with an empty list.
*/
static void
xfs_ail_splice(
struct list_head *list,
xfs_lsn_t lsn)
{
- struct xfs_log_item *lip = cur ? cur->item : NULL;
- struct xfs_log_item *next_lip;
+ struct xfs_log_item *lip;
+
+ ASSERT(!list_empty(list));
/*
- * Get a new cursor if we don't have a placeholder or the existing one
- * has been invalidated.
+ * Use the cursor to determine the insertion point if one is
+ * provided. If not, or if the one we got is not valid,
+ * find the place in the AIL where the items belong.
*/
- if (!lip || (__psint_t)lip & 1) {
+ lip = cur ? cur->item : NULL;
+ if (!lip || (__psint_t) lip & 1)
lip = __xfs_trans_ail_cursor_last(ailp, lsn);
- if (!lip) {
- /* The list is empty, so just splice and return. */
- if (cur)
- cur->item = NULL;
- list_splice(list, &ailp->xa_ail);
- return;
- }
- }
+ /*
+ * If a cursor is provided, we know we're processing the AIL
+ * in lsn order, and future items to be spliced in will
+ * follow the last one being inserted now. Update the
+ * cursor to point to that last item, now while we have a
+ * reliable pointer to it.
+ */
+ if (cur)
+ cur->item = list_entry(list->prev, struct xfs_log_item, li_ail);
/*
- * Our cursor points to the item we want to insert _after_, so we have
- * to update the cursor to point to the end of the list we are splicing
- * in so that it points to the correct location for the next splice.
- * i.e. before the splice
- *
- * lsn -> lsn -> lsn + x -> lsn + x ...
- * ^
- * | cursor points here
- *
- * After the splice we have:
- *
- * lsn -> lsn -> lsn -> lsn -> .... -> lsn -> lsn + x -> lsn + x ...
- * ^ ^
- * | cursor points here | needs to move here
- *
- * So we set the cursor to the last item in the list to be spliced
- * before we execute the splice, resulting in the cursor pointing to
- * the correct item after the splice occurs.
+ * Finally perform the splice. Unless the AIL was empty,
+ * lip points to the item in the AIL _after_ which the new
+ * items should go. If lip is null the AIL was empty, so
+ * the new items go at the head of the AIL.
*/
- if (cur) {
- next_lip = list_entry(list->prev, struct xfs_log_item, li_ail);
- cur->item = next_lip;
- }
- list_splice(list, &lip->li_ail);
+ if (lip)
+ list_splice(list, &lip->li_ail);
+ else
+ list_splice(list, &ailp->xa_ail);
}
/*
int i;
LIST_HEAD(tmp);
+ ASSERT(nr_items > 0); /* Not required, but true. */
mlip = xfs_ail_min(ailp);
for (i = 0; i < nr_items; i++) {
list_add(&lip->li_ail, &tmp);
}
- xfs_ail_splice(ailp, cur, &tmp, lsn);
+ if (!list_empty(&tmp))
+ xfs_ail_splice(ailp, cur, &tmp, lsn);
if (!mlip_changed) {
spin_unlock(&ailp->xa_lock);
list_for_each_entry(lidp, &tp->t_items, lid_trans) {
blip = (struct xfs_buf_log_item *)lidp->lid_item;
if (blip->bli_item.li_type == XFS_LI_BUF &&
- XFS_BUF_TARGET(blip->bli_buf) == target &&
+ blip->bli_buf->b_target == target &&
XFS_BUF_ADDR(blip->bli_buf) == blkno &&
XFS_BUF_COUNT(blip->bli_buf) == len)
return blip->bli_buf;
{
struct xfs_buf_log_item *bip;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == NULL);
/*
return NULL;
}
- ASSERT(!XFS_BUF_GETERROR(bp));
+ ASSERT(!bp->b_error);
_xfs_trans_bjoin(tp, bp, 1);
trace_xfs_trans_get_buf(bp->b_fspriv);
return (flags & XBF_TRYLOCK) ?
EAGAIN : XFS_ERROR(ENOMEM);
- if (XFS_BUF_GETERROR(bp) != 0) {
+ if (bp->b_error) {
+ error = bp->b_error;
xfs_ioerror_alert("xfs_trans_read_buf", mp,
bp, blkno);
- error = XFS_BUF_GETERROR(bp);
xfs_buf_relse(bp);
return error;
}
ASSERT(xfs_buf_islocked(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bp->b_fspriv != NULL);
- ASSERT((XFS_BUF_ISERROR(bp)) == 0);
+ ASSERT(!bp->b_error);
if (!(XFS_BUF_ISDONE(bp))) {
trace_xfs_trans_read_buf_io(bp, _RET_IP_);
ASSERT(!XFS_BUF_ISASYNC(bp));
return (flags & XBF_TRYLOCK) ?
0 : XFS_ERROR(ENOMEM);
}
- if (XFS_BUF_GETERROR(bp) != 0) {
- XFS_BUF_SUPER_STALE(bp);
- error = XFS_BUF_GETERROR(bp);
-
+ if (bp->b_error) {
+ error = bp->b_error;
+ XFS_BUF_SUPER_STALE(bp);
xfs_ioerror_alert("xfs_trans_read_buf", mp,
bp, blkno);
if (tp->t_flags & XFS_TRANS_DIRTY)
if (XFS_BUF_ISSTALE(bp) && XFS_BUF_ISDELAYWRITE(bp))
xfs_notice(mp, "about to pop assert, bp == 0x%p", bp);
#endif
- ASSERT((XFS_BUF_BFLAGS(bp) & (XBF_STALE|XBF_DELWRI)) !=
+ ASSERT((bp->b_flags & (XBF_STALE|XBF_DELWRI)) !=
(XBF_STALE|XBF_DELWRI));
trace_xfs_trans_read_buf_shut(bp, _RET_IP_);
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(!(bip->bli_flags & XFS_BLI_STALE));
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(!(bip->bli_flags & XFS_BLI_STALE));
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT((first <= last) && (last < XFS_BUF_COUNT(bp)));
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(atomic_read(&bip->bli_refcount) > 0);
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(atomic_read(&bip->bli_refcount) > 0);
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(atomic_read(&bip->bli_refcount) > 0);
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(atomic_read(&bip->bli_refcount) > 0);
{
xfs_buf_log_item_t *bip = bp->b_fspriv;
- ASSERT(XFS_BUF_ISBUSY(bp));
ASSERT(bp->b_transp == tp);
ASSERT(bip != NULL);
ASSERT(type == XFS_BLF_UDQUOT_BUF ||
bp = xfs_buf_read(mp->m_ddev_targp, d, BTOBB(byte_cnt),
XBF_LOCK | XBF_MAPPED | XBF_DONT_BLOCK);
- error = XFS_BUF_GETERROR(bp);
+ if (!bp)
+ return XFS_ERROR(ENOMEM);
+ error = bp->b_error;
if (error) {
xfs_ioerror_alert("xfs_readlink",
ip->i_mount, bp, XFS_BUF_ADDR(bp));
byte_cnt = pathlen;
pathlen -= byte_cnt;
- memcpy(link, XFS_BUF_PTR(bp), byte_cnt);
+ memcpy(link, bp->b_addr, byte_cnt);
xfs_buf_relse(bp);
}
byte_cnt = XFS_FSB_TO_B(mp, mval[n].br_blockcount);
bp = xfs_trans_get_buf(tp, mp->m_ddev_targp, d,
BTOBB(byte_cnt), 0);
- ASSERT(bp && !XFS_BUF_GETERROR(bp));
+ ASSERT(!xfs_buf_geterror(bp));
if (pathlen < byte_cnt) {
byte_cnt = pathlen;
}
pathlen -= byte_cnt;
- memcpy(XFS_BUF_PTR(bp), cur_chunk, byte_cnt);
+ memcpy(bp->b_addr, cur_chunk, byte_cnt);
cur_chunk += byte_cnt;
xfs_trans_log_buf(tp, bp, 0, byte_cnt - 1);
mp, bp, XFS_BUF_ADDR(bp));
break;
}
- memset(XFS_BUF_PTR(bp) +
+ memset(bp->b_addr +
(offset - XFS_FSB_TO_B(mp, imap.br_startoff)),
0, lastoffset - offset + 1);
XFS_BUF_UNDONE(bp);
* since nobody else can modify it.
*/
#define current_cred() \
- (*(__force struct cred **)¤t->cred)
+ rcu_dereference_protected(current->cred, 1)
/**
* __task_cred - Access a task's objective credentials
#define get_current_user() \
({ \
struct user_struct *__u; \
- struct cred *__cred; \
+ const struct cred *__cred; \
__cred = current_cred(); \
__u = get_uid(__cred->user); \
__u; \
#define get_current_groups() \
({ \
struct group_info *__groups; \
- struct cred *__cred; \
+ const struct cred *__cred; \
__cred = current_cred(); \
__groups = get_group_info(__cred->group_info); \
__groups; \
#ifdef CONFIG_MMU
extern int handle_mm_fault(struct mm_struct *mm, struct vm_area_struct *vma,
unsigned long address, unsigned int flags);
+extern int fixup_user_fault(struct task_struct *tsk, struct mm_struct *mm,
+ unsigned long address, unsigned int fault_flags);
#else
static inline int handle_mm_fault(struct mm_struct *mm,
struct vm_area_struct *vma, unsigned long address,
BUG();
return VM_FAULT_SIGBUS;
}
+static inline int fixup_user_fault(struct task_struct *tsk,
+ struct mm_struct *mm, unsigned long address,
+ unsigned int fault_flags)
+{
+ /* should never happen if there's no MMU */
+ BUG();
+ return -EFAULT;
+}
#endif
extern int make_pages_present(unsigned long addr, unsigned long end);
int get_user_pages_fast(unsigned long start, int nr_pages, int write,
struct page **pages);
struct page *get_dump_page(unsigned long addr);
-extern int fixup_user_fault(struct task_struct *tsk, struct mm_struct *mm,
- unsigned long address, unsigned int fault_flags);
extern int try_to_release_page(struct page * page, gfp_t gfp_mask);
extern void do_invalidatepage(struct page *page, unsigned long offset);
#define MAX_LINKS 32
struct sockaddr_nl {
- sa_family_t nl_family; /* AF_NETLINK */
+ __kernel_sa_family_t nl_family; /* AF_NETLINK */
unsigned short nl_pad; /* zero */
__u32 nl_pid; /* port ID */
__u32 nl_groups; /* multicast groups mask */
return -ENOSYS;
}
+static inline const void *of_get_property(const struct device_node *node,
+ const char *name,
+ int *lenp)
+{
+ return NULL;
+}
+
#endif /* CONFIG_OF */
static inline int of_property_read_u32(const struct device_node *np,
#define PF_DUMPCORE 0x00000200 /* dumped core */
#define PF_SIGNALED 0x00000400 /* killed by a signal */
#define PF_MEMALLOC 0x00000800 /* Allocating memory */
+#define PF_NPROC_EXCEEDED 0x00001000 /* set_user noticed that RLIMIT_NPROC was exceeded */
#define PF_USED_MATH 0x00002000 /* if unset the fpu must be initialized before use */
#define PF_FREEZING 0x00004000 /* freeze in progress. do not account to load */
#define PF_NOFREEZE 0x00008000 /* this thread should not be frozen */
#define _K_SS_ALIGNSIZE (__alignof__ (struct sockaddr *))
/* Implementation specific desired alignment */
+typedef unsigned short __kernel_sa_family_t;
+
struct __kernel_sockaddr_storage {
- unsigned short ss_family; /* address family */
+ __kernel_sa_family_t ss_family; /* address family */
/* Following field(s) are implementation specific */
char __data[_K_SS_MAXSIZE - sizeof(unsigned short)];
/* space to achieve desired size, */
extern void socket_seq_show(struct seq_file *seq);
#endif
-typedef unsigned short sa_family_t;
+typedef __kernel_sa_family_t sa_family_t;
/*
* 1003.1g requires sa_family_t and that sa_data is char.
{
__u8 flags = 0;
- if (inet_sk(sk)->transparent)
+ if (inet_sk(sk)->transparent || inet_sk(sk)->hdrincl)
flags |= FLOWI_FLAG_ANYSRC;
if (sk->sk_protocol == IPPROTO_TCP)
flags |= FLOWI_FLAG_PRECOW_METRICS;
+++ /dev/null
-/*
- * linux/sound/wm8915.h -- Platform data for WM8915
- *
- * Copyright 2011 Wolfson Microelectronics. PLC.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __LINUX_SND_WM8903_H
-#define __LINUX_SND_WM8903_H
-
-enum wm8915_inmode {
- WM8915_DIFFERRENTIAL_1 = 0, /* IN1xP - IN1xN */
- WM8915_INVERTING = 1, /* IN1xN */
- WM8915_NON_INVERTING = 2, /* IN1xP */
- WM8915_DIFFERENTIAL_2 = 3, /* IN2xP - IN2xP */
-};
-
-/**
- * ReTune Mobile configurations are specified with a label, sample
- * rate and set of values to write (the enable bits will be ignored).
- *
- * Configurations are expected to be generated using the ReTune Mobile
- * control panel in WISCE - see http://www.wolfsonmicro.com/wisce/
- */
-struct wm8915_retune_mobile_config {
- const char *name;
- int rate;
- u16 regs[20];
-};
-
-#define WM8915_SET_DEFAULT 0x10000
-
-struct wm8915_pdata {
- int irq_flags; /** Set IRQ trigger flags; default active low */
-
- int ldo_ena; /** GPIO for LDO1; -1 for none */
-
- int micdet_def; /** Default MICDET_SRC/HP1FB_SRC/MICD_BIAS */
-
- enum wm8915_inmode inl_mode;
- enum wm8915_inmode inr_mode;
-
- u32 spkmute_seq; /** Value for register 0x802 */
-
- int gpio_base;
- u32 gpio_default[5];
-
- int num_retune_mobile_cfgs;
- struct wm8915_retune_mobile_config *retune_mobile_cfgs;
-};
-
-#endif
--- /dev/null
+/*
+ * linux/sound/wm8996.h -- Platform data for WM8996
+ *
+ * Copyright 2011 Wolfson Microelectronics. PLC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_SND_WM8996_H
+#define __LINUX_SND_WM8996_H
+
+enum wm8996_inmode {
+ WM8996_DIFFERRENTIAL_1 = 0, /* IN1xP - IN1xN */
+ WM8996_INVERTING = 1, /* IN1xN */
+ WM8996_NON_INVERTING = 2, /* IN1xP */
+ WM8996_DIFFERENTIAL_2 = 3, /* IN2xP - IN2xP */
+};
+
+/**
+ * ReTune Mobile configurations are specified with a label, sample
+ * rate and set of values to write (the enable bits will be ignored).
+ *
+ * Configurations are expected to be generated using the ReTune Mobile
+ * control panel in WISCE - see http://www.wolfsonmicro.com/wisce/
+ */
+struct wm8996_retune_mobile_config {
+ const char *name;
+ int rate;
+ u16 regs[20];
+};
+
+#define WM8996_SET_DEFAULT 0x10000
+
+struct wm8996_pdata {
+ int irq_flags; /** Set IRQ trigger flags; default active low */
+
+ int ldo_ena; /** GPIO for LDO1; -1 for none */
+
+ int micdet_def; /** Default MICDET_SRC/HP1FB_SRC/MICD_BIAS */
+
+ enum wm8996_inmode inl_mode;
+ enum wm8996_inmode inr_mode;
+
+ u32 spkmute_seq; /** Value for register 0x802 */
+
+ int gpio_base;
+ u32 gpio_default[5];
+
+ int num_retune_mobile_cfgs;
+ struct wm8996_retune_mobile_config *retune_mobile_cfgs;
+};
+
+#endif
kthread.o wait.o kfifo.o sys_ni.o posix-cpu-timers.o mutex.o \
hrtimer.o rwsem.o nsproxy.o srcu.o semaphore.o \
notifier.o ksysfs.o pm_qos_params.o sched_clock.o cred.o \
- async.o range.o jump_label.o
+ async.o range.o
obj-y += groups.o
ifdef CONFIG_FUNCTION_TRACER
obj-$(CONFIG_USER_RETURN_NOTIFIER) += user-return-notifier.o
obj-$(CONFIG_PADATA) += padata.o
obj-$(CONFIG_CRASH_DUMP) += crash_dump.o
+obj-$(CONFIG_JUMP_LABEL) += jump_label.o
ifneq ($(CONFIG_SCHED_OMIT_FRAME_POINTER),y)
# According to Alan Modra <alan@linuxcare.com.au>, the -fno-omit-frame-pointer is
key_fsgid_changed(task);
/* do it
- * - What if a process setreuid()'s and this brings the
- * new uid over his NPROC rlimit? We can check this now
- * cheaply with the new uid cache, so if it matters
- * we should be checking for it. -DaveM
+ * RLIMIT_NPROC limits on user->processes have already been checked
+ * in set_user().
*/
alter_cred_subscribers(new, 2);
if (new->user != old->user)
p->real_cred->user != INIT_USER)
goto bad_fork_free;
}
+ current->flags &= ~PF_NPROC_EXCEEDED;
retval = copy_creds(p, clone_flags);
if (retval < 0)
return 0;
/* For historical reasons, accept CAP_SYS_ADMIN too, with a warning */
if (capable(CAP_SYS_ADMIN)) {
- WARN_ONCE(1, "Attempt to access syslog with CAP_SYS_ADMIN "
- "but no CAP_SYSLOG (deprecated).\n");
+ printk_once(KERN_WARNING "%s (%d): "
+ "Attempt to access syslog with CAP_SYS_ADMIN "
+ "but no CAP_SYSLOG (deprecated).\n",
+ current->comm, task_pid_nr(current));
return 0;
}
return -EPERM;
if (!new_user)
return -EAGAIN;
+ /*
+ * We don't fail in case of NPROC limit excess here because too many
+ * poorly written programs don't check set*uid() return code, assuming
+ * it never fails if called by root. We may still enforce NPROC limit
+ * for programs doing set*uid()+execve() by harmlessly deferring the
+ * failure to the execve() stage.
+ */
if (atomic_read(&new_user->processes) >= rlimit(RLIMIT_NPROC) &&
- new_user != INIT_USER) {
- free_uid(new_user);
- return -EAGAIN;
- }
+ new_user != INIT_USER)
+ current->flags |= PF_NPROC_EXCEEDED;
+ else
+ current->flags &= ~PF_NPROC_EXCEEDED;
free_uid(new->user);
new->user = new_user;
power:power_frequency
This is for userspace compatibility
and will vanish after 5 kernel iterations,
- namely 2.6.41.
+ namely 3.1.
config CONTEXT_SWITCH_TRACER
bool
#define FLUSHING_CACHED_CHARGE (0)
};
static DEFINE_PER_CPU(struct memcg_stock_pcp, memcg_stock);
+static DEFINE_MUTEX(percpu_charge_mutex);
/*
* Try to consume stocked charge on this cpu. If success, one page is consumed
for_each_online_cpu(cpu) {
struct memcg_stock_pcp *stock = &per_cpu(memcg_stock, cpu);
- if (mem_cgroup_same_or_subtree(root_mem, stock->cached) &&
- test_bit(FLUSHING_CACHED_CHARGE, &stock->flags))
+ if (test_bit(FLUSHING_CACHED_CHARGE, &stock->flags))
flush_work(&stock->work);
}
out:
*/
static void drain_all_stock_async(struct mem_cgroup *root_mem)
{
+ /*
+ * If someone calls draining, avoid adding more kworker runs.
+ */
+ if (!mutex_trylock(&percpu_charge_mutex))
+ return;
drain_all_stock(root_mem, false);
+ mutex_unlock(&percpu_charge_mutex);
}
/* This is a synchronous drain interface. */
static void drain_all_stock_sync(struct mem_cgroup *root_mem)
{
/* called when force_empty is called */
+ mutex_lock(&percpu_charge_mutex);
drain_all_stock(root_mem, true);
+ mutex_unlock(&percpu_charge_mutex);
}
/*
return check_bytes8(start, value, bytes);
value64 = value | value << 8 | value << 16 | value << 24;
- value64 = value64 | value64 << 32;
+ value64 = (value64 & 0xffffffff) | value64 << 32;
prefix = 8 - ((unsigned long)start) % 8;
if (prefix) {
new.frozen = 0;
- if (!new.inuse && n->nr_partial < s->min_partial)
+ if (!new.inuse && n->nr_partial > s->min_partial)
m = M_FREE;
else if (new.freelist) {
m = M_PARTIAL;
slab_empty:
if (prior) {
/*
- * Slab still on the partial list.
+ * Slab on the partial list.
*/
remove_partial(n, page);
stat(s, FREE_REMOVE_PARTIAL);
- }
+ } else
+ /* Slab must be on the full list */
+ remove_full(s, page);
spin_unlock_irqrestore(&n->list_lock, flags);
stat(s, FREE_SLAB);
int br_del_if(struct net_bridge *br, struct net_device *dev)
{
struct net_bridge_port *p;
+ bool changed_addr;
p = br_port_get_rtnl(dev);
if (!p || p->br != br)
del_nbp(p);
spin_lock_bh(&br->lock);
- br_stp_recalculate_bridge_id(br);
+ changed_addr = br_stp_recalculate_bridge_id(br);
spin_unlock_bh(&br->lock);
+ if (changed_addr)
+ call_netdevice_notifiers(NETDEV_CHANGEADDR, br->dev);
+
netdev_update_features(br->dev);
return 0;
struct net_device *dev = ptr;
struct net_bridge_port *p;
struct net_bridge *br;
+ bool changed_addr;
int err;
/* register of bridge completed, add sysfs entries */
case NETDEV_CHANGEADDR:
spin_lock_bh(&br->lock);
br_fdb_changeaddr(p, dev->dev_addr);
- br_stp_recalculate_bridge_id(br);
+ changed_addr = br_stp_recalculate_bridge_id(br);
spin_unlock_bh(&br->lock);
+
+ if (changed_addr)
+ call_netdevice_notifiers(NETDEV_CHANGEADDR, br->dev);
+
break;
case NETDEV_CHANGE:
if (table->check && table->check(newinfo, table->valid_hooks)) {
BUGPRINT("The table doesn't like its own initial data, lol\n");
- return ERR_PTR(-EINVAL);
+ ret = -EINVAL;
+ goto free_chainstack;
}
table->private = newinfo;
goto error;
cred->uid = cred->euid = p->creds.uid;
- cred->gid = cred->egid = p->creds.uid;
+ cred->gid = cred->egid = p->creds.gid;
put_cred(p->cred);
p->cred = cred;
}
newskb->pkt_type = PACKET_LOOPBACK;
newskb->ip_summed = CHECKSUM_UNNECESSARY;
WARN_ON(!skb_dst(newskb));
+ skb_dst_force(newskb);
netif_rx_ni(newskb);
return 0;
}
*/
static int do_ip_getsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int __user *optlen)
+ char __user *optval, int __user *optlen, unsigned flags)
{
struct inet_sock *inet = inet_sk(sk);
int val;
msg.msg_control = optval;
msg.msg_controllen = len;
- msg.msg_flags = 0;
+ msg.msg_flags = flags;
if (inet->cmsg_flags & IP_CMSG_PKTINFO) {
struct in_pktinfo info;
{
int err;
- err = do_ip_getsockopt(sk, level, optname, optval, optlen);
+ err = do_ip_getsockopt(sk, level, optname, optval, optlen, 0);
#ifdef CONFIG_NETFILTER
/* we need to exclude all possible ENOPROTOOPTs except default case */
if (err == -ENOPROTOOPT && optname != IP_PKTOPTIONS &&
return compat_mc_getsockopt(sk, level, optname, optval, optlen,
ip_getsockopt);
- err = do_ip_getsockopt(sk, level, optname, optval, optlen);
+ err = do_ip_getsockopt(sk, level, optname, optval, optlen,
+ MSG_CMSG_COMPAT);
#ifdef CONFIG_NETFILTER
/* we need to exclude all possible ENOPROTOOPTs except default case */
struct rtable *rt;
struct flowi4 fl4 = {};
__be32 saddr = iph->saddr;
- __u8 flags = 0;
+ __u8 flags = skb->sk ? inet_sk_flowi_flags(skb->sk) : 0;
unsigned int hh_len;
- if (!skb->sk && addr_type != RTN_LOCAL) {
- if (addr_type == RTN_UNSPEC)
- addr_type = inet_addr_type(net, saddr);
- if (addr_type == RTN_LOCAL || addr_type == RTN_UNICAST)
- flags |= FLOWI_FLAG_ANYSRC;
- else
- saddr = 0;
- }
+ if (addr_type == RTN_UNSPEC)
+ addr_type = inet_addr_type(net, saddr);
+ if (addr_type == RTN_LOCAL || addr_type == RTN_UNICAST)
+ flags |= FLOWI_FLAG_ANYSRC;
+ else
+ saddr = 0;
/* some non-standard hacks like ipt_REJECT.c:send_reset() can cause
* packets with foreign saddr to appear on the NF_INET_LOCAL_OUT hook.
fl4.flowi4_tos = RT_TOS(iph->tos);
fl4.flowi4_oif = skb->sk ? skb->sk->sk_bound_dev_if : 0;
fl4.flowi4_mark = skb->mark;
- fl4.flowi4_flags = skb->sk ? inet_sk_flowi_flags(skb->sk) : flags;
+ fl4.flowi4_flags = flags;
rt = ip_route_output_key(net, &fl4);
if (IS_ERR(rt))
return -1;
flowi4_init_output(&fl4, ipc.oif, sk->sk_mark, tos,
RT_SCOPE_UNIVERSE,
inet->hdrincl ? IPPROTO_RAW : sk->sk_protocol,
- FLOWI_FLAG_CAN_SLEEP, daddr, saddr, 0, 0);
+ inet_sk_flowi_flags(sk) | FLOWI_FLAG_CAN_SLEEP,
+ daddr, saddr, 0, 0);
if (!inet->hdrincl) {
err = raw_probe_proto_opt(&fl4, msg);
{
return ((((__force u32)rt1->rt_key_dst ^ (__force u32)rt2->rt_key_dst) |
((__force u32)rt1->rt_key_src ^ (__force u32)rt2->rt_key_src) |
- (rt1->rt_iif ^ rt2->rt_iif)) == 0);
+ (rt1->rt_route_iif ^ rt2->rt_route_iif)) == 0);
}
static inline int compare_keys(struct rtable *rt1, struct rtable *rt2)
((__force u32)rt1->rt_key_src ^ (__force u32)rt2->rt_key_src) |
(rt1->rt_mark ^ rt2->rt_mark) |
(rt1->rt_key_tos ^ rt2->rt_key_tos) |
- (rt1->rt_oif ^ rt2->rt_oif) |
- (rt1->rt_iif ^ rt2->rt_iif)) == 0;
+ (rt1->rt_route_iif ^ rt2->rt_route_iif) |
+ (rt1->rt_oif ^ rt2->rt_oif)) == 0;
}
static inline int compare_netns(struct rtable *rt1, struct rtable *rt2)
rth = rcu_dereference(rth->dst.rt_next)) {
if ((((__force u32)rth->rt_key_dst ^ (__force u32)daddr) |
((__force u32)rth->rt_key_src ^ (__force u32)saddr) |
- (rth->rt_iif ^ iif) |
- rth->rt_oif |
+ (rth->rt_route_iif ^ iif) |
(rth->rt_key_tos ^ tos)) == 0 &&
rth->rt_mark == skb->mark &&
net_eq(dev_net(rth->dst.dev), net) &&
int mss;
struct rtable *rt;
__u8 rcv_wscale;
- bool ecn_ok;
+ bool ecn_ok = false;
if (!sysctl_tcp_syncookies || !th->ack || th->rst)
goto out;
int mss;
struct dst_entry *dst;
__u8 rcv_wscale;
- bool ecn_ok;
+ bool ecn_ok = false;
if (!sysctl_tcp_syncookies || !th->ack || th->rst)
goto out;
}
break;
case NF_STOLEN:
+ break;
default:
kfree_skb(skb);
}
entry = kzalloc(sizeof(*entry), GFP_ATOMIC);
if (entry == NULL)
- return -ENOMEM;
+ goto out_entry;
if (domain != NULL) {
entry->domain = kstrdup(domain, GFP_ATOMIC);
if (entry->domain == NULL)
- goto cfg_cipsov4_map_add_failure;
+ goto out_domain;
}
if (addr == NULL && mask == NULL) {
} else if (addr != NULL && mask != NULL) {
addrmap = kzalloc(sizeof(*addrmap), GFP_ATOMIC);
if (addrmap == NULL)
- goto cfg_cipsov4_map_add_failure;
+ goto out_addrmap;
INIT_LIST_HEAD(&addrmap->list4);
INIT_LIST_HEAD(&addrmap->list6);
addrinfo = kzalloc(sizeof(*addrinfo), GFP_ATOMIC);
if (addrinfo == NULL)
- goto cfg_cipsov4_map_add_failure;
+ goto out_addrinfo;
addrinfo->type_def.cipsov4 = doi_def;
addrinfo->type = NETLBL_NLTYPE_CIPSOV4;
addrinfo->list.addr = addr->s_addr & mask->s_addr;
entry->type = NETLBL_NLTYPE_ADDRSELECT;
} else {
ret_val = -EINVAL;
- goto cfg_cipsov4_map_add_failure;
+ goto out_addrmap;
}
ret_val = netlbl_domhsh_add(entry, audit_info);
return 0;
cfg_cipsov4_map_add_failure:
- cipso_v4_doi_putdef(doi_def);
+ kfree(addrinfo);
+out_addrinfo:
+ kfree(addrmap);
+out_addrmap:
kfree(entry->domain);
+out_domain:
kfree(entry);
- kfree(addrmap);
- kfree(addrinfo);
+out_entry:
+ cipso_v4_doi_putdef(doi_def);
return ret_val;
}
for (prio = 0; prio < q->bands; prio++) {
struct Qdisc *qdisc = q->queues[prio];
- struct sk_buff *skb = qdisc->dequeue(qdisc);
+ struct sk_buff *skb = qdisc_dequeue_peeked(qdisc);
if (skb) {
qdisc_bstats_update(sch, skb);
sch->q.qlen--;
head->r.index++)
if (ns->profile_ptr[head->r.index])
break;
- if (head->r.index == TOMOYO_MAX_PROFILES)
+ if (head->r.index == TOMOYO_MAX_PROFILES) {
+ head->r.eof = true;
return;
+ }
head->r.step++;
break;
case 2:
tomoyo_io_printf(head, "%u-COMMENT=", index);
tomoyo_set_string(head, comment ? comment->name : "");
tomoyo_set_lf(head);
+ tomoyo_print_namespace(head);
tomoyo_io_printf(head, "%u-PREFERENCE={ ", index);
for (i = 0; i < TOMOYO_MAX_PREF; i++)
tomoyo_io_printf(head, "%s=%u ",
mutex_unlock(®ister_mutex);
} else {
timer = timeri->timer;
+ if (snd_BUG_ON(!timer))
+ goto out;
/* wait, until the active callback is finished */
spin_lock_irq(&timer->lock);
while (timeri->flags & SNDRV_TIMER_IFLG_CALLBACK) {
}
mutex_unlock(®ister_mutex);
}
+ out:
if (timeri->private_free)
timeri->private_free(timeri);
kfree(timeri->owner);
if (err < 0)
return err;
timer = timeri->timer;
+ if (!timer)
+ return -EINVAL;
spin_lock_irqsave(&timer->lock, flags);
timeri->cticks = timeri->ticks;
timeri->pticks = 0;
if (pcm_channels & 2)
{
- foo = ((CLOCK_TICK_RATE / 2) + (arg / 2)) / arg;
- arg = ((CLOCK_TICK_RATE / 2) + (foo / 2)) / foo;
+ foo = ((PIT_TICK_RATE / 2) + (arg / 2)) / arg;
+ arg = ((PIT_TICK_RATE / 2) + (foo / 2)) / foo;
}
else
{
- foo = (CLOCK_TICK_RATE + (arg / 2)) / arg;
- arg = (CLOCK_TICK_RATE + (foo / 2)) / foo;
+ foo = (PIT_TICK_RATE + (arg / 2)) / arg;
+ arg = (PIT_TICK_RATE + (foo / 2)) / foo;
}
pcm_speed = arg;
if (pss_cdrom_port == -1) { /* If cdrom port enablation wasn't requested */
printk(KERN_INFO "PSS: CDROM port not enabled.\n");
- } else if (check_region(pss_cdrom_port, 2)) {
+ } else if (!request_region(pss_cdrom_port, 2, "PSS CDROM")) {
+ pss_cdrom_port = -1;
printk(KERN_ERR "PSS: CDROM I/O port conflict.\n");
} else {
set_io_base(devc, CONF_CDROM, pss_cdrom_port);
if(pssmpu)
unload_pss_mpu(&cfg_mpu);
unload_pss(&cfg);
- }
+ } else if (pss_cdrom_port != -1)
+ release_region(pss_cdrom_port, 2);
if(!pss_keep_settings) /* Keep hardware settings if asked */
{
# ALSA PCI drivers
+config SND_TEA575X
+ tristate
+ depends on SND_FM801_TEA575X_BOOL || SND_ES1968_RADIO || RADIO_SF16FMR2
+ default SND_FM801 || SND_ES1968 || RADIO_SF16FMR2
+
menuconfig SND_PCI
bool "PCI sound devices"
depends on PCI
FM801 chip with a TEA5757 tuner (MediaForte SF256-PCS, SF256-PCP and
SF64-PCR) into the snd-fm801 driver.
-config SND_TEA575X
- tristate
- depends on SND_FM801_TEA575X_BOOL || SND_ES1968_RADIO || RADIO_SF16FMR2
- default SND_FM801 || SND_ES1968 || RADIO_SF16FMR2
-
source "sound/pci/hda/Kconfig"
config SND_HDSP
if (!p_cache)
return NULL;
- p_cache->p_info =
- kmalloc(sizeof(*p_cache->p_info) * control_count, GFP_KERNEL);
+ p_cache->p_info = kzalloc(sizeof(*p_cache->p_info) * control_count,
+ GFP_KERNEL);
if (!p_cache->p_info) {
kfree(p_cache);
return NULL;
}
- memset(p_cache->p_info, 0, sizeof(*p_cache->p_info) * control_count);
p_cache->cache_size_in_bytes = size_in_bytes;
p_cache->control_count = control_count;
p_cache->p_cache = p_dsp_control_buffer;
SND_PCI_QUIRK(0x1043, 0x1653, "ASUS U50", ALC269_AMIC),
SND_PCI_QUIRK(0x1043, 0x1693, "ASUS F50N", ALC269_AMIC),
SND_PCI_QUIRK(0x1043, 0x16a3, "ASUS F5Q", ALC269_AMIC),
- SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_DMIC),
SND_PCI_QUIRK(0x1043, 0x1723, "ASUS P80", ALC269_AMIC),
SND_PCI_QUIRK(0x1043, 0x1743, "ASUS U80", ALC269_AMIC),
SND_PCI_QUIRK(0x1043, 0x1773, "ASUS U20A", ALC269_AMIC),
SND_PCI_QUIRK(0x1043, 0x1883, "ASUS F81Se", ALC269_AMIC),
- SND_PCI_QUIRK(0x1043, 0x831a, "ASUS Eeepc P901",
- ALC269_DMIC),
- SND_PCI_QUIRK(0x1043, 0x834a, "ASUS Eeepc S101",
- ALC269_DMIC),
- SND_PCI_QUIRK(0x1043, 0x8398, "ASUS P1005HA", ALC269_DMIC),
- SND_PCI_QUIRK(0x1043, 0x83ce, "ASUS P1005HA", ALC269_DMIC),
SND_PCI_QUIRK(0x104d, 0x9071, "Sony VAIO", ALC269_AUTO),
SND_PCI_QUIRK(0x10cf, 0x1475, "Lifebook ICH9M-based", ALC269_LIFEBOOK),
SND_PCI_QUIRK(0x152d, 0x1778, "Quanta ON1", ALC269_DMIC),
spec->stream_analog_capture = &alc269_44k_pcm_analog_capture;
}
+static void alc269_fixup_stereo_dmic(struct hda_codec *codec,
+ const struct alc_fixup *fix, int action)
+{
+ int coef;
+
+ if (action != ALC_FIXUP_ACT_INIT)
+ return;
+ /* The digital-mic unit sends PDM (differential signal) instead of
+ * the standard PCM, thus you can't record a valid mono stream as is.
+ * Below is a workaround specific to ALC269 to control the dmic
+ * signal source as mono.
+ */
+ coef = alc_read_coef_idx(codec, 0x07);
+ alc_write_coef_idx(codec, 0x07, coef | 0x80);
+}
+
enum {
ALC269_FIXUP_SONY_VAIO,
ALC275_FIXUP_SONY_VAIO_GPIO2,
ALC275_FIXUP_SONY_HWEQ,
ALC271_FIXUP_DMIC,
ALC269_FIXUP_PCM_44K,
+ ALC269_FIXUP_STEREO_DMIC,
};
static const struct alc_fixup alc269_fixups[] = {
.type = ALC_FIXUP_FUNC,
.v.func = alc269_fixup_pcm_44k,
},
+ [ALC269_FIXUP_STEREO_DMIC] = {
+ .type = ALC_FIXUP_FUNC,
+ .v.func = alc269_fixup_stereo_dmic,
+ },
};
static const struct snd_pci_quirk alc269_fixup_tbl[] = {
SND_PCI_QUIRK(0x1043, 0x1a13, "Asus G73Jw", ALC269_FIXUP_ASUS_G73JW),
+ SND_PCI_QUIRK(0x1043, 0x16e3, "ASUS UX50", ALC269_FIXUP_STEREO_DMIC),
+ SND_PCI_QUIRK(0x1043, 0x831a, "ASUS P901", ALC269_FIXUP_STEREO_DMIC),
+ SND_PCI_QUIRK(0x1043, 0x834a, "ASUS S101", ALC269_FIXUP_STEREO_DMIC),
+ SND_PCI_QUIRK(0x1043, 0x8398, "ASUS P1005", ALC269_FIXUP_STEREO_DMIC),
+ SND_PCI_QUIRK(0x1043, 0x83ce, "ASUS P1005", ALC269_FIXUP_STEREO_DMIC),
SND_PCI_QUIRK(0x104d, 0x9073, "Sony VAIO", ALC275_FIXUP_SONY_VAIO_GPIO2),
SND_PCI_QUIRK(0x104d, 0x907b, "Sony VAIO", ALC275_FIXUP_SONY_HWEQ),
SND_PCI_QUIRK(0x104d, 0x9084, "Sony VAIO", ALC275_FIXUP_SONY_HWEQ),
struct via_spec *spec = codec->spec;
struct nid_path *path;
bool check_dac;
- hda_nid_t pin, dac;
+ hda_nid_t pin, dac = 0;
int err;
pin = spec->autocfg.speaker_pins[0];
break;
case MADIface:
freq_const = 131072000000000ULL;
+ break;
+ default:
+ snd_BUG();
+ return 0;
}
return div_u64(freq_const, period);
switch (hdspm->io_type) {
case MADIface:
- n = 131072000000000ULL; /* 125 MHz */
- break;
+ n = 131072000000000ULL; /* 125 MHz */
+ break;
case MADI:
case AES32:
- n = 110069313433624ULL; /* 105 MHz */
- break;
+ n = 110069313433624ULL; /* 105 MHz */
+ break;
case RayDAT:
case AIO:
- n = 104857600000000ULL; /* 100 MHz */
- break;
+ n = 104857600000000ULL; /* 100 MHz */
+ break;
+ default:
+ snd_BUG();
+ return;
}
n = div_u64(n, rate);
select SND_SOC_WM8900 if I2C
select SND_SOC_WM8903 if I2C
select SND_SOC_WM8904 if I2C
- select SND_SOC_WM8915 if I2C
select SND_SOC_WM8940 if I2C
select SND_SOC_WM8955 if I2C
select SND_SOC_WM8960 if I2C
select SND_SOC_WM8993 if I2C
select SND_SOC_WM8994 if MFD_WM8994
select SND_SOC_WM8995 if SND_SOC_I2C_AND_SPI
+ select SND_SOC_WM8996 if I2C
select SND_SOC_WM9081 if I2C
select SND_SOC_WM9090 if I2C
select SND_SOC_WM9705 if SND_SOC_AC97_BUS
config SND_SOC_WM8904
tristate
-config SND_SOC_WM8915
- tristate
-
config SND_SOC_WM8940
tristate
config SND_SOC_WM8995
tristate
+config SND_SOC_WM8996
+ tristate
+
config SND_SOC_WM9081
tristate
snd-soc-wm8900-objs := wm8900.o
snd-soc-wm8903-objs := wm8903.o
snd-soc-wm8904-objs := wm8904.o
-snd-soc-wm8915-objs := wm8915.o
+snd-soc-wm8996-objs := wm8996.o
snd-soc-wm8940-objs := wm8940.o
snd-soc-wm8955-objs := wm8955.o
snd-soc-wm8960-objs := wm8960.o
obj-$(CONFIG_SND_SOC_WM8900) += snd-soc-wm8900.o
obj-$(CONFIG_SND_SOC_WM8903) += snd-soc-wm8903.o
obj-$(CONFIG_SND_SOC_WM8904) += snd-soc-wm8904.o
-obj-$(CONFIG_SND_SOC_WM8915) += snd-soc-wm8915.o
+obj-$(CONFIG_SND_SOC_WM8996) += snd-soc-wm8996.o
obj-$(CONFIG_SND_SOC_WM8940) += snd-soc-wm8940.o
obj-$(CONFIG_SND_SOC_WM8955) += snd-soc-wm8955.o
obj-$(CONFIG_SND_SOC_WM8960) += snd-soc-wm8960.o
#define SGTL5000_DAP_REG_OFFSET 0x0100
#define SGTL5000_MAX_REG_OFFSET 0x013A
-/* default value of sgtl5000 registers except DAP */
-static const u16 sgtl5000_regs[SGTL5000_MAX_REG_OFFSET >> 1] = {
- 0xa011, /* 0x0000, CHIP_ID. 11 stand for revison 17 */
- 0x0000, /* 0x0002, CHIP_DIG_POWER. */
- 0x0008, /* 0x0004, CHIP_CKL_CTRL */
- 0x0010, /* 0x0006, CHIP_I2S_CTRL */
- 0x0000, /* 0x0008, reserved */
- 0x0008, /* 0x000A, CHIP_SSS_CTRL */
- 0x0000, /* 0x000C, reserved */
- 0x020c, /* 0x000E, CHIP_ADCDAC_CTRL */
- 0x3c3c, /* 0x0010, CHIP_DAC_VOL */
- 0x0000, /* 0x0012, reserved */
- 0x015f, /* 0x0014, CHIP_PAD_STRENGTH */
- 0x0000, /* 0x0016, reserved */
- 0x0000, /* 0x0018, reserved */
- 0x0000, /* 0x001A, reserved */
- 0x0000, /* 0x001E, reserved */
- 0x0000, /* 0x0020, CHIP_ANA_ADC_CTRL */
- 0x1818, /* 0x0022, CHIP_ANA_HP_CTRL */
- 0x0111, /* 0x0024, CHIP_ANN_CTRL */
- 0x0000, /* 0x0026, CHIP_LINREG_CTRL */
- 0x0000, /* 0x0028, CHIP_REF_CTRL */
- 0x0000, /* 0x002A, CHIP_MIC_CTRL */
- 0x0000, /* 0x002C, CHIP_LINE_OUT_CTRL */
- 0x0404, /* 0x002E, CHIP_LINE_OUT_VOL */
- 0x7060, /* 0x0030, CHIP_ANA_POWER */
- 0x5000, /* 0x0032, CHIP_PLL_CTRL */
- 0x0000, /* 0x0034, CHIP_CLK_TOP_CTRL */
- 0x0000, /* 0x0036, CHIP_ANA_STATUS */
- 0x0000, /* 0x0038, reserved */
- 0x0000, /* 0x003A, CHIP_ANA_TEST2 */
- 0x0000, /* 0x003C, CHIP_SHORT_CTRL */
- 0x0000, /* reserved */
-};
-
-/* default value of dap registers */
-static const u16 sgtl5000_dap_regs[] = {
- 0x0000, /* 0x0100, DAP_CONTROL */
- 0x0000, /* 0x0102, DAP_PEQ */
- 0x0040, /* 0x0104, DAP_BASS_ENHANCE */
- 0x051f, /* 0x0106, DAP_BASS_ENHANCE_CTRL */
- 0x0000, /* 0x0108, DAP_AUDIO_EQ */
- 0x0040, /* 0x010A, DAP_SGTL_SURROUND */
- 0x0000, /* 0x010C, DAP_FILTER_COEF_ACCESS */
- 0x0000, /* 0x010E, DAP_COEF_WR_B0_MSB */
- 0x0000, /* 0x0110, DAP_COEF_WR_B0_LSB */
- 0x0000, /* 0x0112, reserved */
- 0x0000, /* 0x0114, reserved */
- 0x002f, /* 0x0116, DAP_AUDIO_EQ_BASS_BAND0 */
- 0x002f, /* 0x0118, DAP_AUDIO_EQ_BAND0 */
- 0x002f, /* 0x011A, DAP_AUDIO_EQ_BAND2 */
- 0x002f, /* 0x011C, DAP_AUDIO_EQ_BAND3 */
- 0x002f, /* 0x011E, DAP_AUDIO_EQ_TREBLE_BAND4 */
- 0x8000, /* 0x0120, DAP_MAIN_CHAN */
- 0x0000, /* 0x0122, DAP_MIX_CHAN */
- 0x0510, /* 0x0124, DAP_AVC_CTRL */
- 0x1473, /* 0x0126, DAP_AVC_THRESHOLD */
- 0x0028, /* 0x0128, DAP_AVC_ATTACK */
- 0x0050, /* 0x012A, DAP_AVC_DECAY */
- 0x0000, /* 0x012C, DAP_COEF_WR_B1_MSB */
- 0x0000, /* 0x012E, DAP_COEF_WR_B1_LSB */
- 0x0000, /* 0x0130, DAP_COEF_WR_B2_MSB */
- 0x0000, /* 0x0132, DAP_COEF_WR_B2_LSB */
- 0x0000, /* 0x0134, DAP_COEF_WR_A1_MSB */
- 0x0000, /* 0x0136, DAP_COEF_WR_A1_LSB */
- 0x0000, /* 0x0138, DAP_COEF_WR_A2_MSB */
- 0x0000, /* 0x013A, DAP_COEF_WR_A2_LSB */
+/* default value of sgtl5000 registers */
+static const u16 sgtl5000_regs[SGTL5000_MAX_REG_OFFSET] = {
+ [SGTL5000_CHIP_CLK_CTRL] = 0x0008,
+ [SGTL5000_CHIP_I2S_CTRL] = 0x0010,
+ [SGTL5000_CHIP_SSS_CTRL] = 0x0008,
+ [SGTL5000_CHIP_DAC_VOL] = 0x3c3c,
+ [SGTL5000_CHIP_PAD_STRENGTH] = 0x015f,
+ [SGTL5000_CHIP_ANA_HP_CTRL] = 0x1818,
+ [SGTL5000_CHIP_ANA_CTRL] = 0x0111,
+ [SGTL5000_CHIP_LINE_OUT_VOL] = 0x0404,
+ [SGTL5000_CHIP_ANA_POWER] = 0x7060,
+ [SGTL5000_CHIP_PLL_CTRL] = 0x5000,
+ [SGTL5000_DAP_BASS_ENHANCE] = 0x0040,
+ [SGTL5000_DAP_BASS_ENHANCE_CTRL] = 0x051f,
+ [SGTL5000_DAP_SURROUND] = 0x0040,
+ [SGTL5000_DAP_EQ_BASS_BAND0] = 0x002f,
+ [SGTL5000_DAP_EQ_BASS_BAND1] = 0x002f,
+ [SGTL5000_DAP_EQ_BASS_BAND2] = 0x002f,
+ [SGTL5000_DAP_EQ_BASS_BAND3] = 0x002f,
+ [SGTL5000_DAP_EQ_BASS_BAND4] = 0x002f,
+ [SGTL5000_DAP_MAIN_CHAN] = 0x8000,
+ [SGTL5000_DAP_AVC_CTRL] = 0x0510,
+ [SGTL5000_DAP_AVC_THRESHOLD] = 0x1473,
+ [SGTL5000_DAP_AVC_ATTACK] = 0x0028,
+ [SGTL5000_DAP_AVC_DECAY] = 0x0050,
};
/* regulator supplies for sgtl5000, VDDD is an optional external supply */
static int sgtl5000_restore_regs(struct snd_soc_codec *codec)
{
u16 *cache = codec->reg_cache;
- int i;
- int regular_regs = SGTL5000_CHIP_SHORT_CTRL >> 1;
+ u16 reg;
/* restore regular registers */
- for (i = 0; i < regular_regs; i++) {
- int reg = i << 1;
+ for (reg = 0; reg <= SGTL5000_CHIP_SHORT_CTRL; reg += 2) {
/* this regs depends on the others */
if (reg == SGTL5000_CHIP_ANA_POWER ||
reg == SGTL5000_CHIP_CLK_CTRL)
continue;
- snd_soc_write(codec, reg, cache[i]);
+ snd_soc_write(codec, reg, cache[reg]);
}
/* restore dap registers */
- for (i = SGTL5000_DAP_REG_OFFSET >> 1;
- i < SGTL5000_MAX_REG_OFFSET >> 1; i++) {
- int reg = i << 1;
-
- snd_soc_write(codec, reg, cache[i]);
- }
+ for (reg = SGTL5000_DAP_REG_OFFSET; reg < SGTL5000_MAX_REG_OFFSET; reg += 2)
+ snd_soc_write(codec, reg, cache[reg]);
/*
* restore power and other regs according
* to set_power() and set_clock()
*/
snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL,
- cache[SGTL5000_CHIP_LINREG_CTRL >> 1]);
+ cache[SGTL5000_CHIP_LINREG_CTRL]);
snd_soc_write(codec, SGTL5000_CHIP_ANA_POWER,
- cache[SGTL5000_CHIP_ANA_POWER >> 1]);
+ cache[SGTL5000_CHIP_ANA_POWER]);
snd_soc_write(codec, SGTL5000_CHIP_CLK_CTRL,
- cache[SGTL5000_CHIP_CLK_CTRL >> 1]);
+ cache[SGTL5000_CHIP_CLK_CTRL]);
snd_soc_write(codec, SGTL5000_CHIP_REF_CTRL,
- cache[SGTL5000_CHIP_REF_CTRL >> 1]);
+ cache[SGTL5000_CHIP_REF_CTRL]);
snd_soc_write(codec, SGTL5000_CHIP_LINE_OUT_CTRL,
- cache[SGTL5000_CHIP_LINE_OUT_CTRL >> 1]);
+ cache[SGTL5000_CHIP_LINE_OUT_CTRL]);
return 0;
}
if (!sgtl5000)
return -ENOMEM;
- /*
- * copy DAP default values to default value array.
- * sgtl5000 register space has a big hole, merge it
- * at init phase makes life easy.
- * FIXME: should we drop 'const' of sgtl5000_regs?
- */
- memcpy((void *)(&sgtl5000_regs[0] + (SGTL5000_DAP_REG_OFFSET >> 1)),
- sgtl5000_dap_regs,
- SGTL5000_MAX_REG_OFFSET - SGTL5000_DAP_REG_OFFSET);
-
i2c_set_clientdata(client, sgtl5000);
ret = snd_soc_register_codec(&client->dev,
+++ /dev/null
-/*
- * wm8915.c - WM8915 audio codec interface
- *
- * Copyright 2011 Wolfson Microelectronics PLC.
- * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/completion.h>
-#include <linux/delay.h>
-#include <linux/pm.h>
-#include <linux/gcd.h>
-#include <linux/gpio.h>
-#include <linux/i2c.h>
-#include <linux/regulator/consumer.h>
-#include <linux/slab.h>
-#include <linux/workqueue.h>
-#include <sound/core.h>
-#include <sound/jack.h>
-#include <sound/pcm.h>
-#include <sound/pcm_params.h>
-#include <sound/soc.h>
-#include <sound/initval.h>
-#include <sound/tlv.h>
-#include <trace/events/asoc.h>
-
-#include <sound/wm8915.h>
-#include "wm8915.h"
-
-#define WM8915_AIFS 2
-
-#define HPOUT1L 1
-#define HPOUT1R 2
-#define HPOUT2L 4
-#define HPOUT2R 8
-
-#define WM8915_NUM_SUPPLIES 4
-static const char *wm8915_supply_names[WM8915_NUM_SUPPLIES] = {
- "DBVDD",
- "AVDD1",
- "AVDD2",
- "CPVDD",
-};
-
-struct wm8915_priv {
- struct snd_soc_codec *codec;
-
- int ldo1ena;
-
- int sysclk;
- int sysclk_src;
-
- int fll_src;
- int fll_fref;
- int fll_fout;
-
- struct completion fll_lock;
-
- u16 dcs_pending;
- struct completion dcs_done;
-
- u16 hpout_ena;
- u16 hpout_pending;
-
- struct regulator_bulk_data supplies[WM8915_NUM_SUPPLIES];
- struct notifier_block disable_nb[WM8915_NUM_SUPPLIES];
-
- struct wm8915_pdata pdata;
-
- int rx_rate[WM8915_AIFS];
- int bclk_rate[WM8915_AIFS];
-
- /* Platform dependant ReTune mobile configuration */
- int num_retune_mobile_texts;
- const char **retune_mobile_texts;
- int retune_mobile_cfg[2];
- struct soc_enum retune_mobile_enum;
-
- struct snd_soc_jack *jack;
- bool detecting;
- bool jack_mic;
- wm8915_polarity_fn polarity_cb;
-
-#ifdef CONFIG_GPIOLIB
- struct gpio_chip gpio_chip;
-#endif
-};
-
-/* We can't use the same notifier block for more than one supply and
- * there's no way I can see to get from a callback to the caller
- * except container_of().
- */
-#define WM8915_REGULATOR_EVENT(n) \
-static int wm8915_regulator_event_##n(struct notifier_block *nb, \
- unsigned long event, void *data) \
-{ \
- struct wm8915_priv *wm8915 = container_of(nb, struct wm8915_priv, \
- disable_nb[n]); \
- if (event & REGULATOR_EVENT_DISABLE) { \
- wm8915->codec->cache_sync = 1; \
- } \
- return 0; \
-}
-
-WM8915_REGULATOR_EVENT(0)
-WM8915_REGULATOR_EVENT(1)
-WM8915_REGULATOR_EVENT(2)
-WM8915_REGULATOR_EVENT(3)
-
-static const u16 wm8915_reg[WM8915_MAX_REGISTER] = {
- [WM8915_SOFTWARE_RESET] = 0x8915,
- [WM8915_POWER_MANAGEMENT_7] = 0x10,
- [WM8915_DAC1_HPOUT1_VOLUME] = 0x88,
- [WM8915_DAC2_HPOUT2_VOLUME] = 0x88,
- [WM8915_DAC1_LEFT_VOLUME] = 0x2c0,
- [WM8915_DAC1_RIGHT_VOLUME] = 0x2c0,
- [WM8915_DAC2_LEFT_VOLUME] = 0x2c0,
- [WM8915_DAC2_RIGHT_VOLUME] = 0x2c0,
- [WM8915_OUTPUT1_LEFT_VOLUME] = 0x80,
- [WM8915_OUTPUT1_RIGHT_VOLUME] = 0x80,
- [WM8915_OUTPUT2_LEFT_VOLUME] = 0x80,
- [WM8915_OUTPUT2_RIGHT_VOLUME] = 0x80,
- [WM8915_MICBIAS_1] = 0x39,
- [WM8915_MICBIAS_2] = 0x39,
- [WM8915_LDO_1] = 0x3,
- [WM8915_LDO_2] = 0x13,
- [WM8915_ACCESSORY_DETECT_MODE_1] = 0x4,
- [WM8915_HEADPHONE_DETECT_1] = 0x20,
- [WM8915_MIC_DETECT_1] = 0x7600,
- [WM8915_MIC_DETECT_2] = 0xbf,
- [WM8915_CHARGE_PUMP_1] = 0x1f25,
- [WM8915_CHARGE_PUMP_2] = 0xab19,
- [WM8915_DC_SERVO_5] = 0x2a2a,
- [WM8915_CONTROL_INTERFACE_1] = 0x8004,
- [WM8915_CLOCKING_1] = 0x10,
- [WM8915_AIF_RATE] = 0x83,
- [WM8915_FLL_CONTROL_4] = 0x5dc0,
- [WM8915_FLL_CONTROL_5] = 0xc84,
- [WM8915_FLL_EFS_2] = 0x2,
- [WM8915_AIF1_TX_LRCLK_1] = 0x80,
- [WM8915_AIF1_TX_LRCLK_2] = 0x8,
- [WM8915_AIF1_RX_LRCLK_1] = 0x80,
- [WM8915_AIF1TX_DATA_CONFIGURATION_1] = 0x1818,
- [WM8915_AIF1RX_DATA_CONFIGURATION] = 0x1818,
- [WM8915_AIF1TX_TEST] = 0x7,
- [WM8915_AIF2_TX_LRCLK_1] = 0x80,
- [WM8915_AIF2_TX_LRCLK_2] = 0x8,
- [WM8915_AIF2_RX_LRCLK_1] = 0x80,
- [WM8915_AIF2TX_DATA_CONFIGURATION_1] = 0x1818,
- [WM8915_AIF2RX_DATA_CONFIGURATION] = 0x1818,
- [WM8915_AIF2TX_TEST] = 0x1,
- [WM8915_DSP1_TX_LEFT_VOLUME] = 0xc0,
- [WM8915_DSP1_TX_RIGHT_VOLUME] = 0xc0,
- [WM8915_DSP1_RX_LEFT_VOLUME] = 0xc0,
- [WM8915_DSP1_RX_RIGHT_VOLUME] = 0xc0,
- [WM8915_DSP1_TX_FILTERS] = 0x2000,
- [WM8915_DSP1_RX_FILTERS_1] = 0x200,
- [WM8915_DSP1_RX_FILTERS_2] = 0x10,
- [WM8915_DSP1_DRC_1] = 0x98,
- [WM8915_DSP1_DRC_2] = 0x845,
- [WM8915_DSP1_RX_EQ_GAINS_1] = 0x6318,
- [WM8915_DSP1_RX_EQ_GAINS_2] = 0x6300,
- [WM8915_DSP1_RX_EQ_BAND_1_A] = 0xfca,
- [WM8915_DSP1_RX_EQ_BAND_1_B] = 0x400,
- [WM8915_DSP1_RX_EQ_BAND_1_PG] = 0xd8,
- [WM8915_DSP1_RX_EQ_BAND_2_A] = 0x1eb5,
- [WM8915_DSP1_RX_EQ_BAND_2_B] = 0xf145,
- [WM8915_DSP1_RX_EQ_BAND_2_C] = 0xb75,
- [WM8915_DSP1_RX_EQ_BAND_2_PG] = 0x1c5,
- [WM8915_DSP1_RX_EQ_BAND_3_A] = 0x1c58,
- [WM8915_DSP1_RX_EQ_BAND_3_B] = 0xf373,
- [WM8915_DSP1_RX_EQ_BAND_3_C] = 0xa54,
- [WM8915_DSP1_RX_EQ_BAND_3_PG] = 0x558,
- [WM8915_DSP1_RX_EQ_BAND_4_A] = 0x168e,
- [WM8915_DSP1_RX_EQ_BAND_4_B] = 0xf829,
- [WM8915_DSP1_RX_EQ_BAND_4_C] = 0x7ad,
- [WM8915_DSP1_RX_EQ_BAND_4_PG] = 0x1103,
- [WM8915_DSP1_RX_EQ_BAND_5_A] = 0x564,
- [WM8915_DSP1_RX_EQ_BAND_5_B] = 0x559,
- [WM8915_DSP1_RX_EQ_BAND_5_PG] = 0x4000,
- [WM8915_DSP2_TX_LEFT_VOLUME] = 0xc0,
- [WM8915_DSP2_TX_RIGHT_VOLUME] = 0xc0,
- [WM8915_DSP2_RX_LEFT_VOLUME] = 0xc0,
- [WM8915_DSP2_RX_RIGHT_VOLUME] = 0xc0,
- [WM8915_DSP2_TX_FILTERS] = 0x2000,
- [WM8915_DSP2_RX_FILTERS_1] = 0x200,
- [WM8915_DSP2_RX_FILTERS_2] = 0x10,
- [WM8915_DSP2_DRC_1] = 0x98,
- [WM8915_DSP2_DRC_2] = 0x845,
- [WM8915_DSP2_RX_EQ_GAINS_1] = 0x6318,
- [WM8915_DSP2_RX_EQ_GAINS_2] = 0x6300,
- [WM8915_DSP2_RX_EQ_BAND_1_A] = 0xfca,
- [WM8915_DSP2_RX_EQ_BAND_1_B] = 0x400,
- [WM8915_DSP2_RX_EQ_BAND_1_PG] = 0xd8,
- [WM8915_DSP2_RX_EQ_BAND_2_A] = 0x1eb5,
- [WM8915_DSP2_RX_EQ_BAND_2_B] = 0xf145,
- [WM8915_DSP2_RX_EQ_BAND_2_C] = 0xb75,
- [WM8915_DSP2_RX_EQ_BAND_2_PG] = 0x1c5,
- [WM8915_DSP2_RX_EQ_BAND_3_A] = 0x1c58,
- [WM8915_DSP2_RX_EQ_BAND_3_B] = 0xf373,
- [WM8915_DSP2_RX_EQ_BAND_3_C] = 0xa54,
- [WM8915_DSP2_RX_EQ_BAND_3_PG] = 0x558,
- [WM8915_DSP2_RX_EQ_BAND_4_A] = 0x168e,
- [WM8915_DSP2_RX_EQ_BAND_4_B] = 0xf829,
- [WM8915_DSP2_RX_EQ_BAND_4_C] = 0x7ad,
- [WM8915_DSP2_RX_EQ_BAND_4_PG] = 0x1103,
- [WM8915_DSP2_RX_EQ_BAND_5_A] = 0x564,
- [WM8915_DSP2_RX_EQ_BAND_5_B] = 0x559,
- [WM8915_DSP2_RX_EQ_BAND_5_PG] = 0x4000,
- [WM8915_OVERSAMPLING] = 0xd,
- [WM8915_SIDETONE] = 0x1040,
- [WM8915_GPIO_1] = 0xa101,
- [WM8915_GPIO_2] = 0xa101,
- [WM8915_GPIO_3] = 0xa101,
- [WM8915_GPIO_4] = 0xa101,
- [WM8915_GPIO_5] = 0xa101,
- [WM8915_PULL_CONTROL_2] = 0x140,
- [WM8915_INTERRUPT_STATUS_1_MASK] = 0x1f,
- [WM8915_INTERRUPT_STATUS_2_MASK] = 0x1ecf,
- [WM8915_RIGHT_PDM_SPEAKER] = 0x1,
- [WM8915_PDM_SPEAKER_MUTE_SEQUENCE] = 0x69,
- [WM8915_PDM_SPEAKER_VOLUME] = 0x66,
- [WM8915_WRITE_SEQUENCER_0] = 0x1,
- [WM8915_WRITE_SEQUENCER_1] = 0x1,
- [WM8915_WRITE_SEQUENCER_3] = 0x6,
- [WM8915_WRITE_SEQUENCER_4] = 0x40,
- [WM8915_WRITE_SEQUENCER_5] = 0x1,
- [WM8915_WRITE_SEQUENCER_6] = 0xf,
- [WM8915_WRITE_SEQUENCER_7] = 0x6,
- [WM8915_WRITE_SEQUENCER_8] = 0x1,
- [WM8915_WRITE_SEQUENCER_9] = 0x3,
- [WM8915_WRITE_SEQUENCER_10] = 0x104,
- [WM8915_WRITE_SEQUENCER_12] = 0x60,
- [WM8915_WRITE_SEQUENCER_13] = 0x11,
- [WM8915_WRITE_SEQUENCER_14] = 0x401,
- [WM8915_WRITE_SEQUENCER_16] = 0x50,
- [WM8915_WRITE_SEQUENCER_17] = 0x3,
- [WM8915_WRITE_SEQUENCER_18] = 0x100,
- [WM8915_WRITE_SEQUENCER_20] = 0x51,
- [WM8915_WRITE_SEQUENCER_21] = 0x3,
- [WM8915_WRITE_SEQUENCER_22] = 0x104,
- [WM8915_WRITE_SEQUENCER_23] = 0xa,
- [WM8915_WRITE_SEQUENCER_24] = 0x60,
- [WM8915_WRITE_SEQUENCER_25] = 0x3b,
- [WM8915_WRITE_SEQUENCER_26] = 0x502,
- [WM8915_WRITE_SEQUENCER_27] = 0x100,
- [WM8915_WRITE_SEQUENCER_28] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_32] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_36] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_40] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_44] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_48] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_52] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_56] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_60] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_64] = 0x1,
- [WM8915_WRITE_SEQUENCER_65] = 0x1,
- [WM8915_WRITE_SEQUENCER_67] = 0x6,
- [WM8915_WRITE_SEQUENCER_68] = 0x40,
- [WM8915_WRITE_SEQUENCER_69] = 0x1,
- [WM8915_WRITE_SEQUENCER_70] = 0xf,
- [WM8915_WRITE_SEQUENCER_71] = 0x6,
- [WM8915_WRITE_SEQUENCER_72] = 0x1,
- [WM8915_WRITE_SEQUENCER_73] = 0x3,
- [WM8915_WRITE_SEQUENCER_74] = 0x104,
- [WM8915_WRITE_SEQUENCER_76] = 0x60,
- [WM8915_WRITE_SEQUENCER_77] = 0x11,
- [WM8915_WRITE_SEQUENCER_78] = 0x401,
- [WM8915_WRITE_SEQUENCER_80] = 0x50,
- [WM8915_WRITE_SEQUENCER_81] = 0x3,
- [WM8915_WRITE_SEQUENCER_82] = 0x100,
- [WM8915_WRITE_SEQUENCER_84] = 0x60,
- [WM8915_WRITE_SEQUENCER_85] = 0x3b,
- [WM8915_WRITE_SEQUENCER_86] = 0x502,
- [WM8915_WRITE_SEQUENCER_87] = 0x100,
- [WM8915_WRITE_SEQUENCER_88] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_92] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_96] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_100] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_104] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_108] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_112] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_116] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_120] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_124] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_128] = 0x1,
- [WM8915_WRITE_SEQUENCER_129] = 0x1,
- [WM8915_WRITE_SEQUENCER_131] = 0x6,
- [WM8915_WRITE_SEQUENCER_132] = 0x40,
- [WM8915_WRITE_SEQUENCER_133] = 0x1,
- [WM8915_WRITE_SEQUENCER_134] = 0xf,
- [WM8915_WRITE_SEQUENCER_135] = 0x6,
- [WM8915_WRITE_SEQUENCER_136] = 0x1,
- [WM8915_WRITE_SEQUENCER_137] = 0x3,
- [WM8915_WRITE_SEQUENCER_138] = 0x106,
- [WM8915_WRITE_SEQUENCER_140] = 0x61,
- [WM8915_WRITE_SEQUENCER_141] = 0x11,
- [WM8915_WRITE_SEQUENCER_142] = 0x401,
- [WM8915_WRITE_SEQUENCER_144] = 0x50,
- [WM8915_WRITE_SEQUENCER_145] = 0x3,
- [WM8915_WRITE_SEQUENCER_146] = 0x102,
- [WM8915_WRITE_SEQUENCER_148] = 0x51,
- [WM8915_WRITE_SEQUENCER_149] = 0x3,
- [WM8915_WRITE_SEQUENCER_150] = 0x106,
- [WM8915_WRITE_SEQUENCER_151] = 0xa,
- [WM8915_WRITE_SEQUENCER_152] = 0x61,
- [WM8915_WRITE_SEQUENCER_153] = 0x3b,
- [WM8915_WRITE_SEQUENCER_154] = 0x502,
- [WM8915_WRITE_SEQUENCER_155] = 0x100,
- [WM8915_WRITE_SEQUENCER_156] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_160] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_164] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_168] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_172] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_176] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_180] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_184] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_188] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_192] = 0x1,
- [WM8915_WRITE_SEQUENCER_193] = 0x1,
- [WM8915_WRITE_SEQUENCER_195] = 0x6,
- [WM8915_WRITE_SEQUENCER_196] = 0x40,
- [WM8915_WRITE_SEQUENCER_197] = 0x1,
- [WM8915_WRITE_SEQUENCER_198] = 0xf,
- [WM8915_WRITE_SEQUENCER_199] = 0x6,
- [WM8915_WRITE_SEQUENCER_200] = 0x1,
- [WM8915_WRITE_SEQUENCER_201] = 0x3,
- [WM8915_WRITE_SEQUENCER_202] = 0x106,
- [WM8915_WRITE_SEQUENCER_204] = 0x61,
- [WM8915_WRITE_SEQUENCER_205] = 0x11,
- [WM8915_WRITE_SEQUENCER_206] = 0x401,
- [WM8915_WRITE_SEQUENCER_208] = 0x50,
- [WM8915_WRITE_SEQUENCER_209] = 0x3,
- [WM8915_WRITE_SEQUENCER_210] = 0x102,
- [WM8915_WRITE_SEQUENCER_212] = 0x61,
- [WM8915_WRITE_SEQUENCER_213] = 0x3b,
- [WM8915_WRITE_SEQUENCER_214] = 0x502,
- [WM8915_WRITE_SEQUENCER_215] = 0x100,
- [WM8915_WRITE_SEQUENCER_216] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_220] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_224] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_228] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_232] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_236] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_240] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_244] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_248] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_252] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_256] = 0x60,
- [WM8915_WRITE_SEQUENCER_258] = 0x601,
- [WM8915_WRITE_SEQUENCER_260] = 0x50,
- [WM8915_WRITE_SEQUENCER_262] = 0x100,
- [WM8915_WRITE_SEQUENCER_264] = 0x1,
- [WM8915_WRITE_SEQUENCER_266] = 0x104,
- [WM8915_WRITE_SEQUENCER_267] = 0x100,
- [WM8915_WRITE_SEQUENCER_268] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_272] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_276] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_280] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_284] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_288] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_292] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_296] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_300] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_304] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_308] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_312] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_316] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_320] = 0x61,
- [WM8915_WRITE_SEQUENCER_322] = 0x601,
- [WM8915_WRITE_SEQUENCER_324] = 0x50,
- [WM8915_WRITE_SEQUENCER_326] = 0x102,
- [WM8915_WRITE_SEQUENCER_328] = 0x1,
- [WM8915_WRITE_SEQUENCER_330] = 0x106,
- [WM8915_WRITE_SEQUENCER_331] = 0x100,
- [WM8915_WRITE_SEQUENCER_332] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_336] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_340] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_344] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_348] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_352] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_356] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_360] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_364] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_368] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_372] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_376] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_380] = 0x2fff,
- [WM8915_WRITE_SEQUENCER_384] = 0x60,
- [WM8915_WRITE_SEQUENCER_386] = 0x601,
- [WM8915_WRITE_SEQUENCER_388] = 0x61,
- [WM8915_WRITE_SEQUENCER_390] = 0x601,
- [WM8915_WRITE_SEQUENCER_392] = 0x50,
- [WM8915_WRITE_SEQUENCER_394] = 0x300,
- [WM8915_WRITE_SEQUENCER_396] = 0x1,
- [WM8915_WRITE_SEQUENCER_398] = 0x304,
- [WM8915_WRITE_SEQUENCER_400] = 0x40,
- [WM8915_WRITE_SEQUENCER_402] = 0xf,
- [WM8915_WRITE_SEQUENCER_404] = 0x1,
- [WM8915_WRITE_SEQUENCER_407] = 0x100,
-};
-
-static const DECLARE_TLV_DB_SCALE(inpga_tlv, 0, 100, 0);
-static const DECLARE_TLV_DB_SCALE(sidetone_tlv, -3600, 150, 0);
-static const DECLARE_TLV_DB_SCALE(digital_tlv, -7200, 75, 1);
-static const DECLARE_TLV_DB_SCALE(out_digital_tlv, -1200, 150, 0);
-static const DECLARE_TLV_DB_SCALE(out_tlv, -900, 75, 0);
-static const DECLARE_TLV_DB_SCALE(spk_tlv, -900, 150, 0);
-static const DECLARE_TLV_DB_SCALE(eq_tlv, -1200, 100, 0);
-
-static const char *sidetone_hpf_text[] = {
- "2.9kHz", "1.5kHz", "735Hz", "403Hz", "196Hz", "98Hz", "49Hz"
-};
-
-static const struct soc_enum sidetone_hpf =
- SOC_ENUM_SINGLE(WM8915_SIDETONE, 7, 6, sidetone_hpf_text);
-
-static const char *hpf_mode_text[] = {
- "HiFi", "Custom", "Voice"
-};
-
-static const struct soc_enum dsp1tx_hpf_mode =
- SOC_ENUM_SINGLE(WM8915_DSP1_TX_FILTERS, 3, 3, hpf_mode_text);
-
-static const struct soc_enum dsp2tx_hpf_mode =
- SOC_ENUM_SINGLE(WM8915_DSP2_TX_FILTERS, 3, 3, hpf_mode_text);
-
-static const char *hpf_cutoff_text[] = {
- "50Hz", "75Hz", "100Hz", "150Hz", "200Hz", "300Hz", "400Hz"
-};
-
-static const struct soc_enum dsp1tx_hpf_cutoff =
- SOC_ENUM_SINGLE(WM8915_DSP1_TX_FILTERS, 0, 7, hpf_cutoff_text);
-
-static const struct soc_enum dsp2tx_hpf_cutoff =
- SOC_ENUM_SINGLE(WM8915_DSP2_TX_FILTERS, 0, 7, hpf_cutoff_text);
-
-static void wm8915_set_retune_mobile(struct snd_soc_codec *codec, int block)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct wm8915_pdata *pdata = &wm8915->pdata;
- int base, best, best_val, save, i, cfg, iface;
-
- if (!wm8915->num_retune_mobile_texts)
- return;
-
- switch (block) {
- case 0:
- base = WM8915_DSP1_RX_EQ_GAINS_1;
- if (snd_soc_read(codec, WM8915_POWER_MANAGEMENT_8) &
- WM8915_DSP1RX_SRC)
- iface = 1;
- else
- iface = 0;
- break;
- case 1:
- base = WM8915_DSP1_RX_EQ_GAINS_2;
- if (snd_soc_read(codec, WM8915_POWER_MANAGEMENT_8) &
- WM8915_DSP2RX_SRC)
- iface = 1;
- else
- iface = 0;
- break;
- default:
- return;
- }
-
- /* Find the version of the currently selected configuration
- * with the nearest sample rate. */
- cfg = wm8915->retune_mobile_cfg[block];
- best = 0;
- best_val = INT_MAX;
- for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
- if (strcmp(pdata->retune_mobile_cfgs[i].name,
- wm8915->retune_mobile_texts[cfg]) == 0 &&
- abs(pdata->retune_mobile_cfgs[i].rate
- - wm8915->rx_rate[iface]) < best_val) {
- best = i;
- best_val = abs(pdata->retune_mobile_cfgs[i].rate
- - wm8915->rx_rate[iface]);
- }
- }
-
- dev_dbg(codec->dev, "ReTune Mobile %d %s/%dHz for %dHz sample rate\n",
- block,
- pdata->retune_mobile_cfgs[best].name,
- pdata->retune_mobile_cfgs[best].rate,
- wm8915->rx_rate[iface]);
-
- /* The EQ will be disabled while reconfiguring it, remember the
- * current configuration.
- */
- save = snd_soc_read(codec, base);
- save &= WM8915_DSP1RX_EQ_ENA;
-
- for (i = 0; i < ARRAY_SIZE(pdata->retune_mobile_cfgs[best].regs); i++)
- snd_soc_update_bits(codec, base + i, 0xffff,
- pdata->retune_mobile_cfgs[best].regs[i]);
-
- snd_soc_update_bits(codec, base, WM8915_DSP1RX_EQ_ENA, save);
-}
-
-/* Icky as hell but saves code duplication */
-static int wm8915_get_retune_mobile_block(const char *name)
-{
- if (strcmp(name, "DSP1 EQ Mode") == 0)
- return 0;
- if (strcmp(name, "DSP2 EQ Mode") == 0)
- return 1;
- return -EINVAL;
-}
-
-static int wm8915_put_retune_mobile_enum(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct wm8915_pdata *pdata = &wm8915->pdata;
- int block = wm8915_get_retune_mobile_block(kcontrol->id.name);
- int value = ucontrol->value.integer.value[0];
-
- if (block < 0)
- return block;
-
- if (value >= pdata->num_retune_mobile_cfgs)
- return -EINVAL;
-
- wm8915->retune_mobile_cfg[block] = value;
-
- wm8915_set_retune_mobile(codec, block);
-
- return 0;
-}
-
-static int wm8915_get_retune_mobile_enum(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int block = wm8915_get_retune_mobile_block(kcontrol->id.name);
-
- ucontrol->value.enumerated.item[0] = wm8915->retune_mobile_cfg[block];
-
- return 0;
-}
-
-static const struct snd_kcontrol_new wm8915_snd_controls[] = {
-SOC_DOUBLE_R_TLV("Capture Volume", WM8915_LEFT_LINE_INPUT_VOLUME,
- WM8915_RIGHT_LINE_INPUT_VOLUME, 0, 31, 0, inpga_tlv),
-SOC_DOUBLE_R("Capture ZC Switch", WM8915_LEFT_LINE_INPUT_VOLUME,
- WM8915_RIGHT_LINE_INPUT_VOLUME, 5, 1, 0),
-
-SOC_DOUBLE_TLV("DAC1 Sidetone Volume", WM8915_DAC1_MIXER_VOLUMES,
- 0, 5, 24, 0, sidetone_tlv),
-SOC_DOUBLE_TLV("DAC2 Sidetone Volume", WM8915_DAC2_MIXER_VOLUMES,
- 0, 5, 24, 0, sidetone_tlv),
-SOC_SINGLE("Sidetone LPF Switch", WM8915_SIDETONE, 12, 1, 0),
-SOC_ENUM("Sidetone HPF Cut-off", sidetone_hpf),
-SOC_SINGLE("Sidetone HPF Switch", WM8915_SIDETONE, 6, 1, 0),
-
-SOC_DOUBLE_R_TLV("DSP1 Capture Volume", WM8915_DSP1_TX_LEFT_VOLUME,
- WM8915_DSP1_TX_RIGHT_VOLUME, 1, 96, 0, digital_tlv),
-SOC_DOUBLE_R_TLV("DSP2 Capture Volume", WM8915_DSP2_TX_LEFT_VOLUME,
- WM8915_DSP2_TX_RIGHT_VOLUME, 1, 96, 0, digital_tlv),
-
-SOC_SINGLE("DSP1 Capture Notch Filter Switch", WM8915_DSP1_TX_FILTERS,
- 13, 1, 0),
-SOC_DOUBLE("DSP1 Capture HPF Switch", WM8915_DSP1_TX_FILTERS, 12, 11, 1, 0),
-SOC_ENUM("DSP1 Capture HPF Mode", dsp1tx_hpf_mode),
-SOC_ENUM("DSP1 Capture HPF Cutoff", dsp1tx_hpf_cutoff),
-
-SOC_SINGLE("DSP2 Capture Notch Filter Switch", WM8915_DSP2_TX_FILTERS,
- 13, 1, 0),
-SOC_DOUBLE("DSP2 Capture HPF Switch", WM8915_DSP2_TX_FILTERS, 12, 11, 1, 0),
-SOC_ENUM("DSP2 Capture HPF Mode", dsp2tx_hpf_mode),
-SOC_ENUM("DSP2 Capture HPF Cutoff", dsp2tx_hpf_cutoff),
-
-SOC_DOUBLE_R_TLV("DSP1 Playback Volume", WM8915_DSP1_RX_LEFT_VOLUME,
- WM8915_DSP1_RX_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
-SOC_SINGLE("DSP1 Playback Switch", WM8915_DSP1_RX_FILTERS_1, 9, 1, 1),
-
-SOC_DOUBLE_R_TLV("DSP2 Playback Volume", WM8915_DSP2_RX_LEFT_VOLUME,
- WM8915_DSP2_RX_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
-SOC_SINGLE("DSP2 Playback Switch", WM8915_DSP2_RX_FILTERS_1, 9, 1, 1),
-
-SOC_DOUBLE_R_TLV("DAC1 Volume", WM8915_DAC1_LEFT_VOLUME,
- WM8915_DAC1_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
-SOC_DOUBLE_R("DAC1 Switch", WM8915_DAC1_LEFT_VOLUME,
- WM8915_DAC1_RIGHT_VOLUME, 9, 1, 1),
-
-SOC_DOUBLE_R_TLV("DAC2 Volume", WM8915_DAC2_LEFT_VOLUME,
- WM8915_DAC2_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
-SOC_DOUBLE_R("DAC2 Switch", WM8915_DAC2_LEFT_VOLUME,
- WM8915_DAC2_RIGHT_VOLUME, 9, 1, 1),
-
-SOC_SINGLE("Speaker High Performance Switch", WM8915_OVERSAMPLING, 3, 1, 0),
-SOC_SINGLE("DMIC High Performance Switch", WM8915_OVERSAMPLING, 2, 1, 0),
-SOC_SINGLE("ADC High Performance Switch", WM8915_OVERSAMPLING, 1, 1, 0),
-SOC_SINGLE("DAC High Performance Switch", WM8915_OVERSAMPLING, 0, 1, 0),
-
-SOC_SINGLE("DAC Soft Mute Switch", WM8915_DAC_SOFTMUTE, 1, 1, 0),
-SOC_SINGLE("DAC Slow Soft Mute Switch", WM8915_DAC_SOFTMUTE, 0, 1, 0),
-
-SOC_DOUBLE_TLV("Digital Output 1 Volume", WM8915_DAC1_HPOUT1_VOLUME, 0, 4,
- 8, 0, out_digital_tlv),
-SOC_DOUBLE_TLV("Digital Output 2 Volume", WM8915_DAC2_HPOUT2_VOLUME, 0, 4,
- 8, 0, out_digital_tlv),
-
-SOC_DOUBLE_R_TLV("Output 1 Volume", WM8915_OUTPUT1_LEFT_VOLUME,
- WM8915_OUTPUT1_RIGHT_VOLUME, 0, 12, 0, out_tlv),
-SOC_DOUBLE_R("Output 1 ZC Switch", WM8915_OUTPUT1_LEFT_VOLUME,
- WM8915_OUTPUT1_RIGHT_VOLUME, 7, 1, 0),
-
-SOC_DOUBLE_R_TLV("Output 2 Volume", WM8915_OUTPUT2_LEFT_VOLUME,
- WM8915_OUTPUT2_RIGHT_VOLUME, 0, 12, 0, out_tlv),
-SOC_DOUBLE_R("Output 2 ZC Switch", WM8915_OUTPUT2_LEFT_VOLUME,
- WM8915_OUTPUT2_RIGHT_VOLUME, 7, 1, 0),
-
-SOC_DOUBLE_TLV("Speaker Volume", WM8915_PDM_SPEAKER_VOLUME, 0, 4, 8, 0,
- spk_tlv),
-SOC_DOUBLE_R("Speaker Switch", WM8915_LEFT_PDM_SPEAKER,
- WM8915_RIGHT_PDM_SPEAKER, 3, 1, 1),
-SOC_DOUBLE_R("Speaker ZC Switch", WM8915_LEFT_PDM_SPEAKER,
- WM8915_RIGHT_PDM_SPEAKER, 2, 1, 0),
-
-SOC_SINGLE("DSP1 EQ Switch", WM8915_DSP1_RX_EQ_GAINS_1, 0, 1, 0),
-SOC_SINGLE("DSP2 EQ Switch", WM8915_DSP2_RX_EQ_GAINS_1, 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new wm8915_eq_controls[] = {
-SOC_SINGLE_TLV("DSP1 EQ B1 Volume", WM8915_DSP1_RX_EQ_GAINS_1, 11, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP1 EQ B2 Volume", WM8915_DSP1_RX_EQ_GAINS_1, 6, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP1 EQ B3 Volume", WM8915_DSP1_RX_EQ_GAINS_1, 1, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP1 EQ B4 Volume", WM8915_DSP1_RX_EQ_GAINS_2, 11, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP1 EQ B5 Volume", WM8915_DSP1_RX_EQ_GAINS_2, 6, 31, 0,
- eq_tlv),
-
-SOC_SINGLE_TLV("DSP2 EQ B1 Volume", WM8915_DSP2_RX_EQ_GAINS_1, 11, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP2 EQ B2 Volume", WM8915_DSP2_RX_EQ_GAINS_1, 6, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP2 EQ B3 Volume", WM8915_DSP2_RX_EQ_GAINS_1, 1, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP2 EQ B4 Volume", WM8915_DSP2_RX_EQ_GAINS_2, 11, 31, 0,
- eq_tlv),
-SOC_SINGLE_TLV("DSP2 EQ B5 Volume", WM8915_DSP2_RX_EQ_GAINS_2, 6, 31, 0,
- eq_tlv),
-};
-
-static int cp_event(struct snd_soc_dapm_widget *w,
- struct snd_kcontrol *kcontrol, int event)
-{
- switch (event) {
- case SND_SOC_DAPM_POST_PMU:
- msleep(5);
- break;
- default:
- BUG();
- return -EINVAL;
- }
-
- return 0;
-}
-
-static int rmv_short_event(struct snd_soc_dapm_widget *w,
- struct snd_kcontrol *kcontrol, int event)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(w->codec);
-
- /* Record which outputs we enabled */
- switch (event) {
- case SND_SOC_DAPM_PRE_PMD:
- wm8915->hpout_pending &= ~w->shift;
- break;
- case SND_SOC_DAPM_PRE_PMU:
- wm8915->hpout_pending |= w->shift;
- break;
- default:
- BUG();
- return -EINVAL;
- }
-
- return 0;
-}
-
-static void wait_for_dc_servo(struct snd_soc_codec *codec, u16 mask)
-{
- struct i2c_client *i2c = to_i2c_client(codec->dev);
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int i, ret;
- unsigned long timeout = 200;
-
- snd_soc_write(codec, WM8915_DC_SERVO_2, mask);
-
- /* Use the interrupt if possible */
- do {
- if (i2c->irq) {
- timeout = wait_for_completion_timeout(&wm8915->dcs_done,
- msecs_to_jiffies(200));
- if (timeout == 0)
- dev_err(codec->dev, "DC servo timed out\n");
-
- } else {
- msleep(1);
- if (--i) {
- timeout = 0;
- break;
- }
- }
-
- ret = snd_soc_read(codec, WM8915_DC_SERVO_2);
- dev_dbg(codec->dev, "DC servo state: %x\n", ret);
- } while (ret & mask);
-
- if (timeout == 0)
- dev_err(codec->dev, "DC servo timed out for %x\n", mask);
- else
- dev_dbg(codec->dev, "DC servo complete for %x\n", mask);
-}
-
-static void wm8915_seq_notifier(struct snd_soc_dapm_context *dapm,
- enum snd_soc_dapm_type event, int subseq)
-{
- struct snd_soc_codec *codec = container_of(dapm,
- struct snd_soc_codec, dapm);
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- u16 val, mask;
-
- /* Complete any pending DC servo starts */
- if (wm8915->dcs_pending) {
- dev_dbg(codec->dev, "Starting DC servo for %x\n",
- wm8915->dcs_pending);
-
- /* Trigger a startup sequence */
- wait_for_dc_servo(codec, wm8915->dcs_pending
- << WM8915_DCS_TRIG_STARTUP_0_SHIFT);
-
- wm8915->dcs_pending = 0;
- }
-
- if (wm8915->hpout_pending != wm8915->hpout_ena) {
- dev_dbg(codec->dev, "Applying RMV_SHORTs %x->%x\n",
- wm8915->hpout_ena, wm8915->hpout_pending);
-
- val = 0;
- mask = 0;
- if (wm8915->hpout_pending & HPOUT1L) {
- val |= WM8915_HPOUT1L_RMV_SHORT;
- mask |= WM8915_HPOUT1L_RMV_SHORT;
- } else {
- mask |= WM8915_HPOUT1L_RMV_SHORT |
- WM8915_HPOUT1L_OUTP |
- WM8915_HPOUT1L_DLY;
- }
-
- if (wm8915->hpout_pending & HPOUT1R) {
- val |= WM8915_HPOUT1R_RMV_SHORT;
- mask |= WM8915_HPOUT1R_RMV_SHORT;
- } else {
- mask |= WM8915_HPOUT1R_RMV_SHORT |
- WM8915_HPOUT1R_OUTP |
- WM8915_HPOUT1R_DLY;
- }
-
- snd_soc_update_bits(codec, WM8915_ANALOGUE_HP_1, mask, val);
-
- val = 0;
- mask = 0;
- if (wm8915->hpout_pending & HPOUT2L) {
- val |= WM8915_HPOUT2L_RMV_SHORT;
- mask |= WM8915_HPOUT2L_RMV_SHORT;
- } else {
- mask |= WM8915_HPOUT2L_RMV_SHORT |
- WM8915_HPOUT2L_OUTP |
- WM8915_HPOUT2L_DLY;
- }
-
- if (wm8915->hpout_pending & HPOUT2R) {
- val |= WM8915_HPOUT2R_RMV_SHORT;
- mask |= WM8915_HPOUT2R_RMV_SHORT;
- } else {
- mask |= WM8915_HPOUT2R_RMV_SHORT |
- WM8915_HPOUT2R_OUTP |
- WM8915_HPOUT2R_DLY;
- }
-
- snd_soc_update_bits(codec, WM8915_ANALOGUE_HP_2, mask, val);
-
- wm8915->hpout_ena = wm8915->hpout_pending;
- }
-}
-
-static int dcs_start(struct snd_soc_dapm_widget *w,
- struct snd_kcontrol *kcontrol, int event)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(w->codec);
-
- switch (event) {
- case SND_SOC_DAPM_POST_PMU:
- wm8915->dcs_pending |= 1 << w->shift;
- break;
- default:
- BUG();
- return -EINVAL;
- }
-
- return 0;
-}
-
-static const char *sidetone_text[] = {
- "IN1", "IN2",
-};
-
-static const struct soc_enum left_sidetone_enum =
- SOC_ENUM_SINGLE(WM8915_SIDETONE, 0, 2, sidetone_text);
-
-static const struct snd_kcontrol_new left_sidetone =
- SOC_DAPM_ENUM("Left Sidetone", left_sidetone_enum);
-
-static const struct soc_enum right_sidetone_enum =
- SOC_ENUM_SINGLE(WM8915_SIDETONE, 1, 2, sidetone_text);
-
-static const struct snd_kcontrol_new right_sidetone =
- SOC_DAPM_ENUM("Right Sidetone", right_sidetone_enum);
-
-static const char *spk_text[] = {
- "DAC1L", "DAC1R", "DAC2L", "DAC2R"
-};
-
-static const struct soc_enum spkl_enum =
- SOC_ENUM_SINGLE(WM8915_LEFT_PDM_SPEAKER, 0, 4, spk_text);
-
-static const struct snd_kcontrol_new spkl_mux =
- SOC_DAPM_ENUM("SPKL", spkl_enum);
-
-static const struct soc_enum spkr_enum =
- SOC_ENUM_SINGLE(WM8915_RIGHT_PDM_SPEAKER, 0, 4, spk_text);
-
-static const struct snd_kcontrol_new spkr_mux =
- SOC_DAPM_ENUM("SPKR", spkr_enum);
-
-static const char *dsp1rx_text[] = {
- "AIF1", "AIF2"
-};
-
-static const struct soc_enum dsp1rx_enum =
- SOC_ENUM_SINGLE(WM8915_POWER_MANAGEMENT_8, 0, 2, dsp1rx_text);
-
-static const struct snd_kcontrol_new dsp1rx =
- SOC_DAPM_ENUM("DSP1RX", dsp1rx_enum);
-
-static const char *dsp2rx_text[] = {
- "AIF2", "AIF1"
-};
-
-static const struct soc_enum dsp2rx_enum =
- SOC_ENUM_SINGLE(WM8915_POWER_MANAGEMENT_8, 4, 2, dsp2rx_text);
-
-static const struct snd_kcontrol_new dsp2rx =
- SOC_DAPM_ENUM("DSP2RX", dsp2rx_enum);
-
-static const char *aif2tx_text[] = {
- "DSP2", "DSP1", "AIF1"
-};
-
-static const struct soc_enum aif2tx_enum =
- SOC_ENUM_SINGLE(WM8915_POWER_MANAGEMENT_8, 6, 3, aif2tx_text);
-
-static const struct snd_kcontrol_new aif2tx =
- SOC_DAPM_ENUM("AIF2TX", aif2tx_enum);
-
-static const char *inmux_text[] = {
- "ADC", "DMIC1", "DMIC2"
-};
-
-static const struct soc_enum in1_enum =
- SOC_ENUM_SINGLE(WM8915_POWER_MANAGEMENT_7, 0, 3, inmux_text);
-
-static const struct snd_kcontrol_new in1_mux =
- SOC_DAPM_ENUM("IN1 Mux", in1_enum);
-
-static const struct soc_enum in2_enum =
- SOC_ENUM_SINGLE(WM8915_POWER_MANAGEMENT_7, 4, 3, inmux_text);
-
-static const struct snd_kcontrol_new in2_mux =
- SOC_DAPM_ENUM("IN2 Mux", in2_enum);
-
-static const struct snd_kcontrol_new dac2r_mix[] = {
-SOC_DAPM_SINGLE("Right Sidetone Switch", WM8915_DAC2_RIGHT_MIXER_ROUTING,
- 5, 1, 0),
-SOC_DAPM_SINGLE("Left Sidetone Switch", WM8915_DAC2_RIGHT_MIXER_ROUTING,
- 4, 1, 0),
-SOC_DAPM_SINGLE("DSP2 Switch", WM8915_DAC2_RIGHT_MIXER_ROUTING, 1, 1, 0),
-SOC_DAPM_SINGLE("DSP1 Switch", WM8915_DAC2_RIGHT_MIXER_ROUTING, 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dac2l_mix[] = {
-SOC_DAPM_SINGLE("Right Sidetone Switch", WM8915_DAC2_LEFT_MIXER_ROUTING,
- 5, 1, 0),
-SOC_DAPM_SINGLE("Left Sidetone Switch", WM8915_DAC2_LEFT_MIXER_ROUTING,
- 4, 1, 0),
-SOC_DAPM_SINGLE("DSP2 Switch", WM8915_DAC2_LEFT_MIXER_ROUTING, 1, 1, 0),
-SOC_DAPM_SINGLE("DSP1 Switch", WM8915_DAC2_LEFT_MIXER_ROUTING, 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dac1r_mix[] = {
-SOC_DAPM_SINGLE("Right Sidetone Switch", WM8915_DAC1_RIGHT_MIXER_ROUTING,
- 5, 1, 0),
-SOC_DAPM_SINGLE("Left Sidetone Switch", WM8915_DAC1_RIGHT_MIXER_ROUTING,
- 4, 1, 0),
-SOC_DAPM_SINGLE("DSP2 Switch", WM8915_DAC1_RIGHT_MIXER_ROUTING, 1, 1, 0),
-SOC_DAPM_SINGLE("DSP1 Switch", WM8915_DAC1_RIGHT_MIXER_ROUTING, 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dac1l_mix[] = {
-SOC_DAPM_SINGLE("Right Sidetone Switch", WM8915_DAC1_LEFT_MIXER_ROUTING,
- 5, 1, 0),
-SOC_DAPM_SINGLE("Left Sidetone Switch", WM8915_DAC1_LEFT_MIXER_ROUTING,
- 4, 1, 0),
-SOC_DAPM_SINGLE("DSP2 Switch", WM8915_DAC1_LEFT_MIXER_ROUTING, 1, 1, 0),
-SOC_DAPM_SINGLE("DSP1 Switch", WM8915_DAC1_LEFT_MIXER_ROUTING, 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dsp1txl[] = {
-SOC_DAPM_SINGLE("IN1 Switch", WM8915_DSP1_TX_LEFT_MIXER_ROUTING,
- 1, 1, 0),
-SOC_DAPM_SINGLE("DAC Switch", WM8915_DSP1_TX_LEFT_MIXER_ROUTING,
- 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dsp1txr[] = {
-SOC_DAPM_SINGLE("IN1 Switch", WM8915_DSP1_TX_RIGHT_MIXER_ROUTING,
- 1, 1, 0),
-SOC_DAPM_SINGLE("DAC Switch", WM8915_DSP1_TX_RIGHT_MIXER_ROUTING,
- 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dsp2txl[] = {
-SOC_DAPM_SINGLE("IN1 Switch", WM8915_DSP2_TX_LEFT_MIXER_ROUTING,
- 1, 1, 0),
-SOC_DAPM_SINGLE("DAC Switch", WM8915_DSP2_TX_LEFT_MIXER_ROUTING,
- 0, 1, 0),
-};
-
-static const struct snd_kcontrol_new dsp2txr[] = {
-SOC_DAPM_SINGLE("IN1 Switch", WM8915_DSP2_TX_RIGHT_MIXER_ROUTING,
- 1, 1, 0),
-SOC_DAPM_SINGLE("DAC Switch", WM8915_DSP2_TX_RIGHT_MIXER_ROUTING,
- 0, 1, 0),
-};
-
-
-static const struct snd_soc_dapm_widget wm8915_dapm_widgets[] = {
-SND_SOC_DAPM_INPUT("IN1LN"),
-SND_SOC_DAPM_INPUT("IN1LP"),
-SND_SOC_DAPM_INPUT("IN1RN"),
-SND_SOC_DAPM_INPUT("IN1RP"),
-
-SND_SOC_DAPM_INPUT("IN2LN"),
-SND_SOC_DAPM_INPUT("IN2LP"),
-SND_SOC_DAPM_INPUT("IN2RN"),
-SND_SOC_DAPM_INPUT("IN2RP"),
-
-SND_SOC_DAPM_INPUT("DMIC1DAT"),
-SND_SOC_DAPM_INPUT("DMIC2DAT"),
-
-SND_SOC_DAPM_SUPPLY_S("SYSCLK", 1, WM8915_AIF_CLOCKING_1, 0, 0, NULL, 0),
-SND_SOC_DAPM_SUPPLY_S("SYSDSPCLK", 2, WM8915_CLOCKING_1, 1, 0, NULL, 0),
-SND_SOC_DAPM_SUPPLY_S("AIFCLK", 2, WM8915_CLOCKING_1, 2, 0, NULL, 0),
-SND_SOC_DAPM_SUPPLY_S("Charge Pump", 2, WM8915_CHARGE_PUMP_1, 15, 0, cp_event,
- SND_SOC_DAPM_POST_PMU),
-
-SND_SOC_DAPM_SUPPLY("LDO2", WM8915_POWER_MANAGEMENT_2, 1, 0, NULL, 0),
-SND_SOC_DAPM_MICBIAS("MICB2", WM8915_POWER_MANAGEMENT_1, 9, 0),
-SND_SOC_DAPM_MICBIAS("MICB1", WM8915_POWER_MANAGEMENT_1, 8, 0),
-
-SND_SOC_DAPM_PGA("IN1L PGA", WM8915_POWER_MANAGEMENT_2, 5, 0, NULL, 0),
-SND_SOC_DAPM_PGA("IN1R PGA", WM8915_POWER_MANAGEMENT_2, 4, 0, NULL, 0),
-
-SND_SOC_DAPM_MUX("IN1L Mux", SND_SOC_NOPM, 0, 0, &in1_mux),
-SND_SOC_DAPM_MUX("IN1R Mux", SND_SOC_NOPM, 0, 0, &in1_mux),
-SND_SOC_DAPM_MUX("IN2L Mux", SND_SOC_NOPM, 0, 0, &in2_mux),
-SND_SOC_DAPM_MUX("IN2R Mux", SND_SOC_NOPM, 0, 0, &in2_mux),
-
-SND_SOC_DAPM_PGA("IN1L", WM8915_POWER_MANAGEMENT_7, 2, 0, NULL, 0),
-SND_SOC_DAPM_PGA("IN1R", WM8915_POWER_MANAGEMENT_7, 3, 0, NULL, 0),
-SND_SOC_DAPM_PGA("IN2L", WM8915_POWER_MANAGEMENT_7, 6, 0, NULL, 0),
-SND_SOC_DAPM_PGA("IN2R", WM8915_POWER_MANAGEMENT_7, 7, 0, NULL, 0),
-
-SND_SOC_DAPM_SUPPLY("DMIC2", WM8915_POWER_MANAGEMENT_7, 9, 0, NULL, 0),
-SND_SOC_DAPM_SUPPLY("DMIC1", WM8915_POWER_MANAGEMENT_7, 8, 0, NULL, 0),
-
-SND_SOC_DAPM_ADC("DMIC2L", NULL, WM8915_POWER_MANAGEMENT_3, 5, 0),
-SND_SOC_DAPM_ADC("DMIC2R", NULL, WM8915_POWER_MANAGEMENT_3, 4, 0),
-SND_SOC_DAPM_ADC("DMIC1L", NULL, WM8915_POWER_MANAGEMENT_3, 3, 0),
-SND_SOC_DAPM_ADC("DMIC1R", NULL, WM8915_POWER_MANAGEMENT_3, 2, 0),
-
-SND_SOC_DAPM_ADC("ADCL", NULL, WM8915_POWER_MANAGEMENT_3, 1, 0),
-SND_SOC_DAPM_ADC("ADCR", NULL, WM8915_POWER_MANAGEMENT_3, 0, 0),
-
-SND_SOC_DAPM_MUX("Left Sidetone", SND_SOC_NOPM, 0, 0, &left_sidetone),
-SND_SOC_DAPM_MUX("Right Sidetone", SND_SOC_NOPM, 0, 0, &right_sidetone),
-
-SND_SOC_DAPM_AIF_IN("DSP2RXL", NULL, 0, WM8915_POWER_MANAGEMENT_3, 11, 0),
-SND_SOC_DAPM_AIF_IN("DSP2RXR", NULL, 1, WM8915_POWER_MANAGEMENT_3, 10, 0),
-SND_SOC_DAPM_AIF_IN("DSP1RXL", NULL, 0, WM8915_POWER_MANAGEMENT_3, 9, 0),
-SND_SOC_DAPM_AIF_IN("DSP1RXR", NULL, 1, WM8915_POWER_MANAGEMENT_3, 8, 0),
-
-SND_SOC_DAPM_MIXER("DSP2TXL", WM8915_POWER_MANAGEMENT_5, 11, 0,
- dsp2txl, ARRAY_SIZE(dsp2txl)),
-SND_SOC_DAPM_MIXER("DSP2TXR", WM8915_POWER_MANAGEMENT_5, 10, 0,
- dsp2txr, ARRAY_SIZE(dsp2txr)),
-SND_SOC_DAPM_MIXER("DSP1TXL", WM8915_POWER_MANAGEMENT_5, 9, 0,
- dsp1txl, ARRAY_SIZE(dsp1txl)),
-SND_SOC_DAPM_MIXER("DSP1TXR", WM8915_POWER_MANAGEMENT_5, 8, 0,
- dsp1txr, ARRAY_SIZE(dsp1txr)),
-
-SND_SOC_DAPM_MIXER("DAC2L Mixer", SND_SOC_NOPM, 0, 0,
- dac2l_mix, ARRAY_SIZE(dac2l_mix)),
-SND_SOC_DAPM_MIXER("DAC2R Mixer", SND_SOC_NOPM, 0, 0,
- dac2r_mix, ARRAY_SIZE(dac2r_mix)),
-SND_SOC_DAPM_MIXER("DAC1L Mixer", SND_SOC_NOPM, 0, 0,
- dac1l_mix, ARRAY_SIZE(dac1l_mix)),
-SND_SOC_DAPM_MIXER("DAC1R Mixer", SND_SOC_NOPM, 0, 0,
- dac1r_mix, ARRAY_SIZE(dac1r_mix)),
-
-SND_SOC_DAPM_DAC("DAC2L", NULL, WM8915_POWER_MANAGEMENT_5, 3, 0),
-SND_SOC_DAPM_DAC("DAC2R", NULL, WM8915_POWER_MANAGEMENT_5, 2, 0),
-SND_SOC_DAPM_DAC("DAC1L", NULL, WM8915_POWER_MANAGEMENT_5, 1, 0),
-SND_SOC_DAPM_DAC("DAC1R", NULL, WM8915_POWER_MANAGEMENT_5, 0, 0),
-
-SND_SOC_DAPM_AIF_IN("AIF2RX1", "AIF2 Playback", 1,
- WM8915_POWER_MANAGEMENT_4, 9, 0),
-SND_SOC_DAPM_AIF_IN("AIF2RX0", "AIF2 Playback", 2,
- WM8915_POWER_MANAGEMENT_4, 8, 0),
-
-SND_SOC_DAPM_AIF_IN("AIF2TX1", "AIF2 Capture", 1,
- WM8915_POWER_MANAGEMENT_6, 9, 0),
-SND_SOC_DAPM_AIF_IN("AIF2TX0", "AIF2 Capture", 2,
- WM8915_POWER_MANAGEMENT_6, 8, 0),
-
-SND_SOC_DAPM_AIF_IN("AIF1RX5", "AIF1 Playback", 5,
- WM8915_POWER_MANAGEMENT_4, 5, 0),
-SND_SOC_DAPM_AIF_IN("AIF1RX4", "AIF1 Playback", 4,
- WM8915_POWER_MANAGEMENT_4, 4, 0),
-SND_SOC_DAPM_AIF_IN("AIF1RX3", "AIF1 Playback", 3,
- WM8915_POWER_MANAGEMENT_4, 3, 0),
-SND_SOC_DAPM_AIF_IN("AIF1RX2", "AIF1 Playback", 2,
- WM8915_POWER_MANAGEMENT_4, 2, 0),
-SND_SOC_DAPM_AIF_IN("AIF1RX1", "AIF1 Playback", 1,
- WM8915_POWER_MANAGEMENT_4, 1, 0),
-SND_SOC_DAPM_AIF_IN("AIF1RX0", "AIF1 Playback", 0,
- WM8915_POWER_MANAGEMENT_4, 0, 0),
-
-SND_SOC_DAPM_AIF_OUT("AIF1TX5", "AIF1 Capture", 5,
- WM8915_POWER_MANAGEMENT_6, 5, 0),
-SND_SOC_DAPM_AIF_OUT("AIF1TX4", "AIF1 Capture", 4,
- WM8915_POWER_MANAGEMENT_6, 4, 0),
-SND_SOC_DAPM_AIF_OUT("AIF1TX3", "AIF1 Capture", 3,
- WM8915_POWER_MANAGEMENT_6, 3, 0),
-SND_SOC_DAPM_AIF_OUT("AIF1TX2", "AIF1 Capture", 2,
- WM8915_POWER_MANAGEMENT_6, 2, 0),
-SND_SOC_DAPM_AIF_OUT("AIF1TX1", "AIF1 Capture", 1,
- WM8915_POWER_MANAGEMENT_6, 1, 0),
-SND_SOC_DAPM_AIF_OUT("AIF1TX0", "AIF1 Capture", 0,
- WM8915_POWER_MANAGEMENT_6, 0, 0),
-
-/* We route as stereo pairs so define some dummy widgets to squash
- * things down for now. RXA = 0,1, RXB = 2,3 and so on */
-SND_SOC_DAPM_PGA("AIF1RXA", SND_SOC_NOPM, 0, 0, NULL, 0),
-SND_SOC_DAPM_PGA("AIF1RXB", SND_SOC_NOPM, 0, 0, NULL, 0),
-SND_SOC_DAPM_PGA("AIF1RXC", SND_SOC_NOPM, 0, 0, NULL, 0),
-SND_SOC_DAPM_PGA("AIF2RX", SND_SOC_NOPM, 0, 0, NULL, 0),
-SND_SOC_DAPM_PGA("DSP2TX", SND_SOC_NOPM, 0, 0, NULL, 0),
-
-SND_SOC_DAPM_MUX("DSP1RX", SND_SOC_NOPM, 0, 0, &dsp1rx),
-SND_SOC_DAPM_MUX("DSP2RX", SND_SOC_NOPM, 0, 0, &dsp2rx),
-SND_SOC_DAPM_MUX("AIF2TX", SND_SOC_NOPM, 0, 0, &aif2tx),
-
-SND_SOC_DAPM_MUX("SPKL", SND_SOC_NOPM, 0, 0, &spkl_mux),
-SND_SOC_DAPM_MUX("SPKR", SND_SOC_NOPM, 0, 0, &spkr_mux),
-SND_SOC_DAPM_PGA("SPKL PGA", WM8915_LEFT_PDM_SPEAKER, 4, 0, NULL, 0),
-SND_SOC_DAPM_PGA("SPKR PGA", WM8915_RIGHT_PDM_SPEAKER, 4, 0, NULL, 0),
-
-SND_SOC_DAPM_PGA_S("HPOUT2L PGA", 0, WM8915_POWER_MANAGEMENT_1, 7, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2L_DLY", 1, WM8915_ANALOGUE_HP_2, 5, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2L_DCS", 2, WM8915_DC_SERVO_1, 2, 0, dcs_start,
- SND_SOC_DAPM_POST_PMU),
-SND_SOC_DAPM_PGA_S("HPOUT2L_OUTP", 3, WM8915_ANALOGUE_HP_2, 6, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2L_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT2L, 0,
- rmv_short_event,
- SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
-
-SND_SOC_DAPM_PGA_S("HPOUT2R PGA", 0, WM8915_POWER_MANAGEMENT_1, 6, 0,NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2R_DLY", 1, WM8915_ANALOGUE_HP_2, 1, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2R_DCS", 2, WM8915_DC_SERVO_1, 3, 0, dcs_start,
- SND_SOC_DAPM_POST_PMU),
-SND_SOC_DAPM_PGA_S("HPOUT2R_OUTP", 3, WM8915_ANALOGUE_HP_2, 2, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT2R_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT2R, 0,
- rmv_short_event,
- SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
-
-SND_SOC_DAPM_PGA_S("HPOUT1L PGA", 0, WM8915_POWER_MANAGEMENT_1, 5, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1L_DLY", 1, WM8915_ANALOGUE_HP_1, 5, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1L_DCS", 2, WM8915_DC_SERVO_1, 0, 0, dcs_start,
- SND_SOC_DAPM_POST_PMU),
-SND_SOC_DAPM_PGA_S("HPOUT1L_OUTP", 3, WM8915_ANALOGUE_HP_1, 6, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1L_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT1L, 0,
- rmv_short_event,
- SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
-
-SND_SOC_DAPM_PGA_S("HPOUT1R PGA", 0, WM8915_POWER_MANAGEMENT_1, 4, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1R_DLY", 1, WM8915_ANALOGUE_HP_1, 1, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1R_DCS", 2, WM8915_DC_SERVO_1, 1, 0, dcs_start,
- SND_SOC_DAPM_POST_PMU),
-SND_SOC_DAPM_PGA_S("HPOUT1R_OUTP", 3, WM8915_ANALOGUE_HP_1, 2, 0, NULL, 0),
-SND_SOC_DAPM_PGA_S("HPOUT1R_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT1R, 0,
- rmv_short_event,
- SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
-
-SND_SOC_DAPM_OUTPUT("HPOUT1L"),
-SND_SOC_DAPM_OUTPUT("HPOUT1R"),
-SND_SOC_DAPM_OUTPUT("HPOUT2L"),
-SND_SOC_DAPM_OUTPUT("HPOUT2R"),
-SND_SOC_DAPM_OUTPUT("SPKDAT"),
-};
-
-static const struct snd_soc_dapm_route wm8915_dapm_routes[] = {
- { "AIFCLK", NULL, "SYSCLK" },
- { "SYSDSPCLK", NULL, "SYSCLK" },
- { "Charge Pump", NULL, "SYSCLK" },
-
- { "MICB1", NULL, "LDO2" },
- { "MICB2", NULL, "LDO2" },
-
- { "IN1L PGA", NULL, "IN2LN" },
- { "IN1L PGA", NULL, "IN2LP" },
- { "IN1L PGA", NULL, "IN1LN" },
- { "IN1L PGA", NULL, "IN1LP" },
-
- { "IN1R PGA", NULL, "IN2RN" },
- { "IN1R PGA", NULL, "IN2RP" },
- { "IN1R PGA", NULL, "IN1RN" },
- { "IN1R PGA", NULL, "IN1RP" },
-
- { "ADCL", NULL, "IN1L PGA" },
-
- { "ADCR", NULL, "IN1R PGA" },
-
- { "DMIC1L", NULL, "DMIC1DAT" },
- { "DMIC1R", NULL, "DMIC1DAT" },
- { "DMIC2L", NULL, "DMIC2DAT" },
- { "DMIC2R", NULL, "DMIC2DAT" },
-
- { "DMIC2L", NULL, "DMIC2" },
- { "DMIC2R", NULL, "DMIC2" },
- { "DMIC1L", NULL, "DMIC1" },
- { "DMIC1R", NULL, "DMIC1" },
-
- { "IN1L Mux", "ADC", "ADCL" },
- { "IN1L Mux", "DMIC1", "DMIC1L" },
- { "IN1L Mux", "DMIC2", "DMIC2L" },
-
- { "IN1R Mux", "ADC", "ADCR" },
- { "IN1R Mux", "DMIC1", "DMIC1R" },
- { "IN1R Mux", "DMIC2", "DMIC2R" },
-
- { "IN2L Mux", "ADC", "ADCL" },
- { "IN2L Mux", "DMIC1", "DMIC1L" },
- { "IN2L Mux", "DMIC2", "DMIC2L" },
-
- { "IN2R Mux", "ADC", "ADCR" },
- { "IN2R Mux", "DMIC1", "DMIC1R" },
- { "IN2R Mux", "DMIC2", "DMIC2R" },
-
- { "Left Sidetone", "IN1", "IN1L Mux" },
- { "Left Sidetone", "IN2", "IN2L Mux" },
-
- { "Right Sidetone", "IN1", "IN1R Mux" },
- { "Right Sidetone", "IN2", "IN2R Mux" },
-
- { "DSP1TXL", "IN1 Switch", "IN1L Mux" },
- { "DSP1TXR", "IN1 Switch", "IN1R Mux" },
-
- { "DSP2TXL", "IN1 Switch", "IN2L Mux" },
- { "DSP2TXR", "IN1 Switch", "IN2R Mux" },
-
- { "AIF1TX0", NULL, "DSP1TXL" },
- { "AIF1TX1", NULL, "DSP1TXR" },
- { "AIF1TX2", NULL, "DSP2TXL" },
- { "AIF1TX3", NULL, "DSP2TXR" },
- { "AIF1TX4", NULL, "AIF2RX0" },
- { "AIF1TX5", NULL, "AIF2RX1" },
-
- { "AIF1RX0", NULL, "AIFCLK" },
- { "AIF1RX1", NULL, "AIFCLK" },
- { "AIF1RX2", NULL, "AIFCLK" },
- { "AIF1RX3", NULL, "AIFCLK" },
- { "AIF1RX4", NULL, "AIFCLK" },
- { "AIF1RX5", NULL, "AIFCLK" },
-
- { "AIF2RX0", NULL, "AIFCLK" },
- { "AIF2RX1", NULL, "AIFCLK" },
-
- { "DSP1RXL", NULL, "SYSDSPCLK" },
- { "DSP1RXR", NULL, "SYSDSPCLK" },
- { "DSP2RXL", NULL, "SYSDSPCLK" },
- { "DSP2RXR", NULL, "SYSDSPCLK" },
- { "DSP1TXL", NULL, "SYSDSPCLK" },
- { "DSP1TXR", NULL, "SYSDSPCLK" },
- { "DSP2TXL", NULL, "SYSDSPCLK" },
- { "DSP2TXR", NULL, "SYSDSPCLK" },
-
- { "AIF1RXA", NULL, "AIF1RX0" },
- { "AIF1RXA", NULL, "AIF1RX1" },
- { "AIF1RXB", NULL, "AIF1RX2" },
- { "AIF1RXB", NULL, "AIF1RX3" },
- { "AIF1RXC", NULL, "AIF1RX4" },
- { "AIF1RXC", NULL, "AIF1RX5" },
-
- { "AIF2RX", NULL, "AIF2RX0" },
- { "AIF2RX", NULL, "AIF2RX1" },
-
- { "AIF2TX", "DSP2", "DSP2TX" },
- { "AIF2TX", "DSP1", "DSP1RX" },
- { "AIF2TX", "AIF1", "AIF1RXC" },
-
- { "DSP1RXL", NULL, "DSP1RX" },
- { "DSP1RXR", NULL, "DSP1RX" },
- { "DSP2RXL", NULL, "DSP2RX" },
- { "DSP2RXR", NULL, "DSP2RX" },
-
- { "DSP2TX", NULL, "DSP2TXL" },
- { "DSP2TX", NULL, "DSP2TXR" },
-
- { "DSP1RX", "AIF1", "AIF1RXA" },
- { "DSP1RX", "AIF2", "AIF2RX" },
-
- { "DSP2RX", "AIF1", "AIF1RXB" },
- { "DSP2RX", "AIF2", "AIF2RX" },
-
- { "DAC2L Mixer", "DSP2 Switch", "DSP2RXL" },
- { "DAC2L Mixer", "DSP1 Switch", "DSP1RXL" },
- { "DAC2L Mixer", "Right Sidetone Switch", "Right Sidetone" },
- { "DAC2L Mixer", "Left Sidetone Switch", "Left Sidetone" },
-
- { "DAC2R Mixer", "DSP2 Switch", "DSP2RXR" },
- { "DAC2R Mixer", "DSP1 Switch", "DSP1RXR" },
- { "DAC2R Mixer", "Right Sidetone Switch", "Right Sidetone" },
- { "DAC2R Mixer", "Left Sidetone Switch", "Left Sidetone" },
-
- { "DAC1L Mixer", "DSP2 Switch", "DSP2RXL" },
- { "DAC1L Mixer", "DSP1 Switch", "DSP1RXL" },
- { "DAC1L Mixer", "Right Sidetone Switch", "Right Sidetone" },
- { "DAC1L Mixer", "Left Sidetone Switch", "Left Sidetone" },
-
- { "DAC1R Mixer", "DSP2 Switch", "DSP2RXR" },
- { "DAC1R Mixer", "DSP1 Switch", "DSP1RXR" },
- { "DAC1R Mixer", "Right Sidetone Switch", "Right Sidetone" },
- { "DAC1R Mixer", "Left Sidetone Switch", "Left Sidetone" },
-
- { "DAC1L", NULL, "DAC1L Mixer" },
- { "DAC1R", NULL, "DAC1R Mixer" },
- { "DAC2L", NULL, "DAC2L Mixer" },
- { "DAC2R", NULL, "DAC2R Mixer" },
-
- { "HPOUT2L PGA", NULL, "Charge Pump" },
- { "HPOUT2L PGA", NULL, "DAC2L" },
- { "HPOUT2L_DLY", NULL, "HPOUT2L PGA" },
- { "HPOUT2L_DCS", NULL, "HPOUT2L_DLY" },
- { "HPOUT2L_OUTP", NULL, "HPOUT2L_DCS" },
- { "HPOUT2L_RMV_SHORT", NULL, "HPOUT2L_OUTP" },
-
- { "HPOUT2R PGA", NULL, "Charge Pump" },
- { "HPOUT2R PGA", NULL, "DAC2R" },
- { "HPOUT2R_DLY", NULL, "HPOUT2R PGA" },
- { "HPOUT2R_DCS", NULL, "HPOUT2R_DLY" },
- { "HPOUT2R_OUTP", NULL, "HPOUT2R_DCS" },
- { "HPOUT2R_RMV_SHORT", NULL, "HPOUT2R_OUTP" },
-
- { "HPOUT1L PGA", NULL, "Charge Pump" },
- { "HPOUT1L PGA", NULL, "DAC1L" },
- { "HPOUT1L_DLY", NULL, "HPOUT1L PGA" },
- { "HPOUT1L_DCS", NULL, "HPOUT1L_DLY" },
- { "HPOUT1L_OUTP", NULL, "HPOUT1L_DCS" },
- { "HPOUT1L_RMV_SHORT", NULL, "HPOUT1L_OUTP" },
-
- { "HPOUT1R PGA", NULL, "Charge Pump" },
- { "HPOUT1R PGA", NULL, "DAC1R" },
- { "HPOUT1R_DLY", NULL, "HPOUT1R PGA" },
- { "HPOUT1R_DCS", NULL, "HPOUT1R_DLY" },
- { "HPOUT1R_OUTP", NULL, "HPOUT1R_DCS" },
- { "HPOUT1R_RMV_SHORT", NULL, "HPOUT1R_OUTP" },
-
- { "HPOUT2L", NULL, "HPOUT2L_RMV_SHORT" },
- { "HPOUT2R", NULL, "HPOUT2R_RMV_SHORT" },
- { "HPOUT1L", NULL, "HPOUT1L_RMV_SHORT" },
- { "HPOUT1R", NULL, "HPOUT1R_RMV_SHORT" },
-
- { "SPKL", "DAC1L", "DAC1L" },
- { "SPKL", "DAC1R", "DAC1R" },
- { "SPKL", "DAC2L", "DAC2L" },
- { "SPKL", "DAC2R", "DAC2R" },
-
- { "SPKR", "DAC1L", "DAC1L" },
- { "SPKR", "DAC1R", "DAC1R" },
- { "SPKR", "DAC2L", "DAC2L" },
- { "SPKR", "DAC2R", "DAC2R" },
-
- { "SPKL PGA", NULL, "SPKL" },
- { "SPKR PGA", NULL, "SPKR" },
-
- { "SPKDAT", NULL, "SPKL PGA" },
- { "SPKDAT", NULL, "SPKR PGA" },
-};
-
-static int wm8915_readable_register(struct snd_soc_codec *codec,
- unsigned int reg)
-{
- /* Due to the sparseness of the register map the compiler
- * output from an explicit switch statement ends up being much
- * more efficient than a table.
- */
- switch (reg) {
- case WM8915_SOFTWARE_RESET:
- case WM8915_POWER_MANAGEMENT_1:
- case WM8915_POWER_MANAGEMENT_2:
- case WM8915_POWER_MANAGEMENT_3:
- case WM8915_POWER_MANAGEMENT_4:
- case WM8915_POWER_MANAGEMENT_5:
- case WM8915_POWER_MANAGEMENT_6:
- case WM8915_POWER_MANAGEMENT_7:
- case WM8915_POWER_MANAGEMENT_8:
- case WM8915_LEFT_LINE_INPUT_VOLUME:
- case WM8915_RIGHT_LINE_INPUT_VOLUME:
- case WM8915_LINE_INPUT_CONTROL:
- case WM8915_DAC1_HPOUT1_VOLUME:
- case WM8915_DAC2_HPOUT2_VOLUME:
- case WM8915_DAC1_LEFT_VOLUME:
- case WM8915_DAC1_RIGHT_VOLUME:
- case WM8915_DAC2_LEFT_VOLUME:
- case WM8915_DAC2_RIGHT_VOLUME:
- case WM8915_OUTPUT1_LEFT_VOLUME:
- case WM8915_OUTPUT1_RIGHT_VOLUME:
- case WM8915_OUTPUT2_LEFT_VOLUME:
- case WM8915_OUTPUT2_RIGHT_VOLUME:
- case WM8915_MICBIAS_1:
- case WM8915_MICBIAS_2:
- case WM8915_LDO_1:
- case WM8915_LDO_2:
- case WM8915_ACCESSORY_DETECT_MODE_1:
- case WM8915_ACCESSORY_DETECT_MODE_2:
- case WM8915_HEADPHONE_DETECT_1:
- case WM8915_HEADPHONE_DETECT_2:
- case WM8915_MIC_DETECT_1:
- case WM8915_MIC_DETECT_2:
- case WM8915_MIC_DETECT_3:
- case WM8915_CHARGE_PUMP_1:
- case WM8915_CHARGE_PUMP_2:
- case WM8915_DC_SERVO_1:
- case WM8915_DC_SERVO_2:
- case WM8915_DC_SERVO_3:
- case WM8915_DC_SERVO_5:
- case WM8915_DC_SERVO_6:
- case WM8915_DC_SERVO_7:
- case WM8915_DC_SERVO_READBACK_0:
- case WM8915_ANALOGUE_HP_1:
- case WM8915_ANALOGUE_HP_2:
- case WM8915_CHIP_REVISION:
- case WM8915_CONTROL_INTERFACE_1:
- case WM8915_WRITE_SEQUENCER_CTRL_1:
- case WM8915_WRITE_SEQUENCER_CTRL_2:
- case WM8915_AIF_CLOCKING_1:
- case WM8915_AIF_CLOCKING_2:
- case WM8915_CLOCKING_1:
- case WM8915_CLOCKING_2:
- case WM8915_AIF_RATE:
- case WM8915_FLL_CONTROL_1:
- case WM8915_FLL_CONTROL_2:
- case WM8915_FLL_CONTROL_3:
- case WM8915_FLL_CONTROL_4:
- case WM8915_FLL_CONTROL_5:
- case WM8915_FLL_CONTROL_6:
- case WM8915_FLL_EFS_1:
- case WM8915_FLL_EFS_2:
- case WM8915_AIF1_CONTROL:
- case WM8915_AIF1_BCLK:
- case WM8915_AIF1_TX_LRCLK_1:
- case WM8915_AIF1_TX_LRCLK_2:
- case WM8915_AIF1_RX_LRCLK_1:
- case WM8915_AIF1_RX_LRCLK_2:
- case WM8915_AIF1TX_DATA_CONFIGURATION_1:
- case WM8915_AIF1TX_DATA_CONFIGURATION_2:
- case WM8915_AIF1RX_DATA_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_0_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_1_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_2_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_3_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_4_CONFIGURATION:
- case WM8915_AIF1TX_CHANNEL_5_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_0_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_1_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_2_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_3_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_4_CONFIGURATION:
- case WM8915_AIF1RX_CHANNEL_5_CONFIGURATION:
- case WM8915_AIF1RX_MONO_CONFIGURATION:
- case WM8915_AIF1TX_TEST:
- case WM8915_AIF2_CONTROL:
- case WM8915_AIF2_BCLK:
- case WM8915_AIF2_TX_LRCLK_1:
- case WM8915_AIF2_TX_LRCLK_2:
- case WM8915_AIF2_RX_LRCLK_1:
- case WM8915_AIF2_RX_LRCLK_2:
- case WM8915_AIF2TX_DATA_CONFIGURATION_1:
- case WM8915_AIF2TX_DATA_CONFIGURATION_2:
- case WM8915_AIF2RX_DATA_CONFIGURATION:
- case WM8915_AIF2TX_CHANNEL_0_CONFIGURATION:
- case WM8915_AIF2TX_CHANNEL_1_CONFIGURATION:
- case WM8915_AIF2RX_CHANNEL_0_CONFIGURATION:
- case WM8915_AIF2RX_CHANNEL_1_CONFIGURATION:
- case WM8915_AIF2RX_MONO_CONFIGURATION:
- case WM8915_AIF2TX_TEST:
- case WM8915_DSP1_TX_LEFT_VOLUME:
- case WM8915_DSP1_TX_RIGHT_VOLUME:
- case WM8915_DSP1_RX_LEFT_VOLUME:
- case WM8915_DSP1_RX_RIGHT_VOLUME:
- case WM8915_DSP1_TX_FILTERS:
- case WM8915_DSP1_RX_FILTERS_1:
- case WM8915_DSP1_RX_FILTERS_2:
- case WM8915_DSP1_DRC_1:
- case WM8915_DSP1_DRC_2:
- case WM8915_DSP1_DRC_3:
- case WM8915_DSP1_DRC_4:
- case WM8915_DSP1_DRC_5:
- case WM8915_DSP1_RX_EQ_GAINS_1:
- case WM8915_DSP1_RX_EQ_GAINS_2:
- case WM8915_DSP1_RX_EQ_BAND_1_A:
- case WM8915_DSP1_RX_EQ_BAND_1_B:
- case WM8915_DSP1_RX_EQ_BAND_1_PG:
- case WM8915_DSP1_RX_EQ_BAND_2_A:
- case WM8915_DSP1_RX_EQ_BAND_2_B:
- case WM8915_DSP1_RX_EQ_BAND_2_C:
- case WM8915_DSP1_RX_EQ_BAND_2_PG:
- case WM8915_DSP1_RX_EQ_BAND_3_A:
- case WM8915_DSP1_RX_EQ_BAND_3_B:
- case WM8915_DSP1_RX_EQ_BAND_3_C:
- case WM8915_DSP1_RX_EQ_BAND_3_PG:
- case WM8915_DSP1_RX_EQ_BAND_4_A:
- case WM8915_DSP1_RX_EQ_BAND_4_B:
- case WM8915_DSP1_RX_EQ_BAND_4_C:
- case WM8915_DSP1_RX_EQ_BAND_4_PG:
- case WM8915_DSP1_RX_EQ_BAND_5_A:
- case WM8915_DSP1_RX_EQ_BAND_5_B:
- case WM8915_DSP1_RX_EQ_BAND_5_PG:
- case WM8915_DSP2_TX_LEFT_VOLUME:
- case WM8915_DSP2_TX_RIGHT_VOLUME:
- case WM8915_DSP2_RX_LEFT_VOLUME:
- case WM8915_DSP2_RX_RIGHT_VOLUME:
- case WM8915_DSP2_TX_FILTERS:
- case WM8915_DSP2_RX_FILTERS_1:
- case WM8915_DSP2_RX_FILTERS_2:
- case WM8915_DSP2_DRC_1:
- case WM8915_DSP2_DRC_2:
- case WM8915_DSP2_DRC_3:
- case WM8915_DSP2_DRC_4:
- case WM8915_DSP2_DRC_5:
- case WM8915_DSP2_RX_EQ_GAINS_1:
- case WM8915_DSP2_RX_EQ_GAINS_2:
- case WM8915_DSP2_RX_EQ_BAND_1_A:
- case WM8915_DSP2_RX_EQ_BAND_1_B:
- case WM8915_DSP2_RX_EQ_BAND_1_PG:
- case WM8915_DSP2_RX_EQ_BAND_2_A:
- case WM8915_DSP2_RX_EQ_BAND_2_B:
- case WM8915_DSP2_RX_EQ_BAND_2_C:
- case WM8915_DSP2_RX_EQ_BAND_2_PG:
- case WM8915_DSP2_RX_EQ_BAND_3_A:
- case WM8915_DSP2_RX_EQ_BAND_3_B:
- case WM8915_DSP2_RX_EQ_BAND_3_C:
- case WM8915_DSP2_RX_EQ_BAND_3_PG:
- case WM8915_DSP2_RX_EQ_BAND_4_A:
- case WM8915_DSP2_RX_EQ_BAND_4_B:
- case WM8915_DSP2_RX_EQ_BAND_4_C:
- case WM8915_DSP2_RX_EQ_BAND_4_PG:
- case WM8915_DSP2_RX_EQ_BAND_5_A:
- case WM8915_DSP2_RX_EQ_BAND_5_B:
- case WM8915_DSP2_RX_EQ_BAND_5_PG:
- case WM8915_DAC1_MIXER_VOLUMES:
- case WM8915_DAC1_LEFT_MIXER_ROUTING:
- case WM8915_DAC1_RIGHT_MIXER_ROUTING:
- case WM8915_DAC2_MIXER_VOLUMES:
- case WM8915_DAC2_LEFT_MIXER_ROUTING:
- case WM8915_DAC2_RIGHT_MIXER_ROUTING:
- case WM8915_DSP1_TX_LEFT_MIXER_ROUTING:
- case WM8915_DSP1_TX_RIGHT_MIXER_ROUTING:
- case WM8915_DSP2_TX_LEFT_MIXER_ROUTING:
- case WM8915_DSP2_TX_RIGHT_MIXER_ROUTING:
- case WM8915_DSP_TX_MIXER_SELECT:
- case WM8915_DAC_SOFTMUTE:
- case WM8915_OVERSAMPLING:
- case WM8915_SIDETONE:
- case WM8915_GPIO_1:
- case WM8915_GPIO_2:
- case WM8915_GPIO_3:
- case WM8915_GPIO_4:
- case WM8915_GPIO_5:
- case WM8915_PULL_CONTROL_1:
- case WM8915_PULL_CONTROL_2:
- case WM8915_INTERRUPT_STATUS_1:
- case WM8915_INTERRUPT_STATUS_2:
- case WM8915_INTERRUPT_RAW_STATUS_2:
- case WM8915_INTERRUPT_STATUS_1_MASK:
- case WM8915_INTERRUPT_STATUS_2_MASK:
- case WM8915_INTERRUPT_CONTROL:
- case WM8915_LEFT_PDM_SPEAKER:
- case WM8915_RIGHT_PDM_SPEAKER:
- case WM8915_PDM_SPEAKER_MUTE_SEQUENCE:
- case WM8915_PDM_SPEAKER_VOLUME:
- return 1;
- default:
- return 0;
- }
-}
-
-static int wm8915_volatile_register(struct snd_soc_codec *codec,
- unsigned int reg)
-{
- switch (reg) {
- case WM8915_SOFTWARE_RESET:
- case WM8915_CHIP_REVISION:
- case WM8915_LDO_1:
- case WM8915_LDO_2:
- case WM8915_INTERRUPT_STATUS_1:
- case WM8915_INTERRUPT_STATUS_2:
- case WM8915_INTERRUPT_RAW_STATUS_2:
- case WM8915_DC_SERVO_READBACK_0:
- case WM8915_DC_SERVO_2:
- case WM8915_DC_SERVO_6:
- case WM8915_DC_SERVO_7:
- case WM8915_FLL_CONTROL_6:
- case WM8915_MIC_DETECT_3:
- case WM8915_HEADPHONE_DETECT_1:
- case WM8915_HEADPHONE_DETECT_2:
- return 1;
- default:
- return 0;
- }
-}
-
-static int wm8915_reset(struct snd_soc_codec *codec)
-{
- return snd_soc_write(codec, WM8915_SOFTWARE_RESET, 0x8915);
-}
-
-static const int bclk_divs[] = {
- 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96
-};
-
-static void wm8915_update_bclk(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int aif, best, cur_val, bclk_rate, bclk_reg, i;
-
- /* Don't bother if we're in a low frequency idle mode that
- * can't support audio.
- */
- if (wm8915->sysclk < 64000)
- return;
-
- for (aif = 0; aif < WM8915_AIFS; aif++) {
- switch (aif) {
- case 0:
- bclk_reg = WM8915_AIF1_BCLK;
- break;
- case 1:
- bclk_reg = WM8915_AIF2_BCLK;
- break;
- }
-
- bclk_rate = wm8915->bclk_rate[aif];
-
- /* Pick a divisor for BCLK as close as we can get to ideal */
- best = 0;
- for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
- cur_val = (wm8915->sysclk / bclk_divs[i]) - bclk_rate;
- if (cur_val < 0) /* BCLK table is sorted */
- break;
- best = i;
- }
- bclk_rate = wm8915->sysclk / bclk_divs[best];
- dev_dbg(codec->dev, "Using BCLK_DIV %d for actual BCLK %dHz\n",
- bclk_divs[best], bclk_rate);
-
- snd_soc_update_bits(codec, bclk_reg,
- WM8915_AIF1_BCLK_DIV_MASK, best);
- }
-}
-
-static int wm8915_set_bias_level(struct snd_soc_codec *codec,
- enum snd_soc_bias_level level)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int ret;
-
- switch (level) {
- case SND_SOC_BIAS_ON:
- break;
-
- case SND_SOC_BIAS_PREPARE:
- if (codec->dapm.bias_level == SND_SOC_BIAS_STANDBY) {
- snd_soc_update_bits(codec, WM8915_POWER_MANAGEMENT_1,
- WM8915_BG_ENA, WM8915_BG_ENA);
- msleep(2);
- }
- break;
-
- case SND_SOC_BIAS_STANDBY:
- if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
- ret = regulator_bulk_enable(ARRAY_SIZE(wm8915->supplies),
- wm8915->supplies);
- if (ret != 0) {
- dev_err(codec->dev,
- "Failed to enable supplies: %d\n",
- ret);
- return ret;
- }
-
- if (wm8915->pdata.ldo_ena >= 0) {
- gpio_set_value_cansleep(wm8915->pdata.ldo_ena,
- 1);
- msleep(5);
- }
-
- codec->cache_only = false;
- snd_soc_cache_sync(codec);
- }
-
- snd_soc_update_bits(codec, WM8915_POWER_MANAGEMENT_1,
- WM8915_BG_ENA, 0);
- break;
-
- case SND_SOC_BIAS_OFF:
- codec->cache_only = true;
- if (wm8915->pdata.ldo_ena >= 0)
- gpio_set_value_cansleep(wm8915->pdata.ldo_ena, 0);
- regulator_bulk_disable(ARRAY_SIZE(wm8915->supplies),
- wm8915->supplies);
- break;
- }
-
- codec->dapm.bias_level = level;
-
- return 0;
-}
-
-static int wm8915_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
-{
- struct snd_soc_codec *codec = dai->codec;
- int aifctrl = 0;
- int bclk = 0;
- int lrclk_tx = 0;
- int lrclk_rx = 0;
- int aifctrl_reg, bclk_reg, lrclk_tx_reg, lrclk_rx_reg;
-
- switch (dai->id) {
- case 0:
- aifctrl_reg = WM8915_AIF1_CONTROL;
- bclk_reg = WM8915_AIF1_BCLK;
- lrclk_tx_reg = WM8915_AIF1_TX_LRCLK_2;
- lrclk_rx_reg = WM8915_AIF1_RX_LRCLK_2;
- break;
- case 1:
- aifctrl_reg = WM8915_AIF2_CONTROL;
- bclk_reg = WM8915_AIF2_BCLK;
- lrclk_tx_reg = WM8915_AIF2_TX_LRCLK_2;
- lrclk_rx_reg = WM8915_AIF2_RX_LRCLK_2;
- break;
- default:
- BUG();
- return -EINVAL;
- }
-
- switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
- case SND_SOC_DAIFMT_NB_NF:
- break;
- case SND_SOC_DAIFMT_IB_NF:
- bclk |= WM8915_AIF1_BCLK_INV;
- break;
- case SND_SOC_DAIFMT_NB_IF:
- lrclk_tx |= WM8915_AIF1TX_LRCLK_INV;
- lrclk_rx |= WM8915_AIF1RX_LRCLK_INV;
- break;
- case SND_SOC_DAIFMT_IB_IF:
- bclk |= WM8915_AIF1_BCLK_INV;
- lrclk_tx |= WM8915_AIF1TX_LRCLK_INV;
- lrclk_rx |= WM8915_AIF1RX_LRCLK_INV;
- break;
- }
-
- switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
- case SND_SOC_DAIFMT_CBS_CFS:
- break;
- case SND_SOC_DAIFMT_CBS_CFM:
- lrclk_tx |= WM8915_AIF1TX_LRCLK_MSTR;
- lrclk_rx |= WM8915_AIF1RX_LRCLK_MSTR;
- break;
- case SND_SOC_DAIFMT_CBM_CFS:
- bclk |= WM8915_AIF1_BCLK_MSTR;
- break;
- case SND_SOC_DAIFMT_CBM_CFM:
- bclk |= WM8915_AIF1_BCLK_MSTR;
- lrclk_tx |= WM8915_AIF1TX_LRCLK_MSTR;
- lrclk_rx |= WM8915_AIF1RX_LRCLK_MSTR;
- break;
- default:
- return -EINVAL;
- }
-
- switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
- case SND_SOC_DAIFMT_DSP_A:
- break;
- case SND_SOC_DAIFMT_DSP_B:
- aifctrl |= 1;
- break;
- case SND_SOC_DAIFMT_I2S:
- aifctrl |= 2;
- break;
- case SND_SOC_DAIFMT_LEFT_J:
- aifctrl |= 3;
- break;
- default:
- return -EINVAL;
- }
-
- snd_soc_update_bits(codec, aifctrl_reg, WM8915_AIF1_FMT_MASK, aifctrl);
- snd_soc_update_bits(codec, bclk_reg,
- WM8915_AIF1_BCLK_INV | WM8915_AIF1_BCLK_MSTR,
- bclk);
- snd_soc_update_bits(codec, lrclk_tx_reg,
- WM8915_AIF1TX_LRCLK_INV |
- WM8915_AIF1TX_LRCLK_MSTR,
- lrclk_tx);
- snd_soc_update_bits(codec, lrclk_rx_reg,
- WM8915_AIF1RX_LRCLK_INV |
- WM8915_AIF1RX_LRCLK_MSTR,
- lrclk_rx);
-
- return 0;
-}
-
-static const int dsp_divs[] = {
- 48000, 32000, 16000, 8000
-};
-
-static int wm8915_hw_params(struct snd_pcm_substream *substream,
- struct snd_pcm_hw_params *params,
- struct snd_soc_dai *dai)
-{
- struct snd_soc_codec *codec = dai->codec;
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int bits, i, bclk_rate;
- int aifdata = 0;
- int lrclk = 0;
- int dsp = 0;
- int aifdata_reg, lrclk_reg, dsp_shift;
-
- switch (dai->id) {
- case 0:
- if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
- (snd_soc_read(codec, WM8915_GPIO_1)) & WM8915_GP1_FN_MASK) {
- aifdata_reg = WM8915_AIF1RX_DATA_CONFIGURATION;
- lrclk_reg = WM8915_AIF1_RX_LRCLK_1;
- } else {
- aifdata_reg = WM8915_AIF1TX_DATA_CONFIGURATION_1;
- lrclk_reg = WM8915_AIF1_TX_LRCLK_1;
- }
- dsp_shift = 0;
- break;
- case 1:
- if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
- (snd_soc_read(codec, WM8915_GPIO_2)) & WM8915_GP2_FN_MASK) {
- aifdata_reg = WM8915_AIF2RX_DATA_CONFIGURATION;
- lrclk_reg = WM8915_AIF2_RX_LRCLK_1;
- } else {
- aifdata_reg = WM8915_AIF2TX_DATA_CONFIGURATION_1;
- lrclk_reg = WM8915_AIF2_TX_LRCLK_1;
- }
- dsp_shift = WM8915_DSP2_DIV_SHIFT;
- break;
- default:
- BUG();
- return -EINVAL;
- }
-
- bclk_rate = snd_soc_params_to_bclk(params);
- if (bclk_rate < 0) {
- dev_err(codec->dev, "Unsupported BCLK rate: %d\n", bclk_rate);
- return bclk_rate;
- }
-
- wm8915->bclk_rate[dai->id] = bclk_rate;
- wm8915->rx_rate[dai->id] = params_rate(params);
-
- /* Needs looking at for TDM */
- bits = snd_pcm_format_width(params_format(params));
- if (bits < 0)
- return bits;
- aifdata |= (bits << WM8915_AIF1TX_WL_SHIFT) | bits;
-
- for (i = 0; i < ARRAY_SIZE(dsp_divs); i++) {
- if (dsp_divs[i] == params_rate(params))
- break;
- }
- if (i == ARRAY_SIZE(dsp_divs)) {
- dev_err(codec->dev, "Unsupported sample rate %dHz\n",
- params_rate(params));
- return -EINVAL;
- }
- dsp |= i << dsp_shift;
-
- wm8915_update_bclk(codec);
-
- lrclk = bclk_rate / params_rate(params);
- dev_dbg(dai->dev, "Using LRCLK rate %d for actual LRCLK %dHz\n",
- lrclk, bclk_rate / lrclk);
-
- snd_soc_update_bits(codec, aifdata_reg,
- WM8915_AIF1TX_WL_MASK |
- WM8915_AIF1TX_SLOT_LEN_MASK,
- aifdata);
- snd_soc_update_bits(codec, lrclk_reg, WM8915_AIF1RX_RATE_MASK,
- lrclk);
- snd_soc_update_bits(codec, WM8915_AIF_CLOCKING_2,
- WM8915_DSP1_DIV_SHIFT << dsp_shift, dsp);
-
- return 0;
-}
-
-static int wm8915_set_sysclk(struct snd_soc_dai *dai,
- int clk_id, unsigned int freq, int dir)
-{
- struct snd_soc_codec *codec = dai->codec;
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int lfclk = 0;
- int ratediv = 0;
- int src;
- int old;
-
- if (freq == wm8915->sysclk && clk_id == wm8915->sysclk_src)
- return 0;
-
- /* Disable SYSCLK while we reconfigure */
- old = snd_soc_read(codec, WM8915_AIF_CLOCKING_1) & WM8915_SYSCLK_ENA;
- snd_soc_update_bits(codec, WM8915_AIF_CLOCKING_1,
- WM8915_SYSCLK_ENA, 0);
-
- switch (clk_id) {
- case WM8915_SYSCLK_MCLK1:
- wm8915->sysclk = freq;
- src = 0;
- break;
- case WM8915_SYSCLK_MCLK2:
- wm8915->sysclk = freq;
- src = 1;
- break;
- case WM8915_SYSCLK_FLL:
- wm8915->sysclk = freq;
- src = 2;
- break;
- default:
- dev_err(codec->dev, "Unsupported clock source %d\n", clk_id);
- return -EINVAL;
- }
-
- switch (wm8915->sysclk) {
- case 6144000:
- snd_soc_update_bits(codec, WM8915_AIF_RATE,
- WM8915_SYSCLK_RATE, 0);
- break;
- case 24576000:
- ratediv = WM8915_SYSCLK_DIV;
- case 12288000:
- snd_soc_update_bits(codec, WM8915_AIF_RATE,
- WM8915_SYSCLK_RATE, WM8915_SYSCLK_RATE);
- break;
- case 32000:
- case 32768:
- lfclk = WM8915_LFCLK_ENA;
- break;
- default:
- dev_warn(codec->dev, "Unsupported clock rate %dHz\n",
- wm8915->sysclk);
- return -EINVAL;
- }
-
- wm8915_update_bclk(codec);
-
- snd_soc_update_bits(codec, WM8915_AIF_CLOCKING_1,
- WM8915_SYSCLK_SRC_MASK | WM8915_SYSCLK_DIV_MASK,
- src << WM8915_SYSCLK_SRC_SHIFT | ratediv);
- snd_soc_update_bits(codec, WM8915_CLOCKING_1, WM8915_LFCLK_ENA, lfclk);
- snd_soc_update_bits(codec, WM8915_AIF_CLOCKING_1,
- WM8915_SYSCLK_ENA, old);
-
- wm8915->sysclk_src = clk_id;
-
- return 0;
-}
-
-struct _fll_div {
- u16 fll_fratio;
- u16 fll_outdiv;
- u16 fll_refclk_div;
- u16 fll_loop_gain;
- u16 fll_ref_freq;
- u16 n;
- u16 theta;
- u16 lambda;
-};
-
-static struct {
- unsigned int min;
- unsigned int max;
- u16 fll_fratio;
- int ratio;
-} fll_fratios[] = {
- { 0, 64000, 4, 16 },
- { 64000, 128000, 3, 8 },
- { 128000, 256000, 2, 4 },
- { 256000, 1000000, 1, 2 },
- { 1000000, 13500000, 0, 1 },
-};
-
-static int fll_factors(struct _fll_div *fll_div, unsigned int Fref,
- unsigned int Fout)
-{
- unsigned int target;
- unsigned int div;
- unsigned int fratio, gcd_fll;
- int i;
-
- /* Fref must be <=13.5MHz */
- div = 1;
- fll_div->fll_refclk_div = 0;
- while ((Fref / div) > 13500000) {
- div *= 2;
- fll_div->fll_refclk_div++;
-
- if (div > 8) {
- pr_err("Can't scale %dMHz input down to <=13.5MHz\n",
- Fref);
- return -EINVAL;
- }
- }
-
- pr_debug("FLL Fref=%u Fout=%u\n", Fref, Fout);
-
- /* Apply the division for our remaining calculations */
- Fref /= div;
-
- if (Fref >= 3000000)
- fll_div->fll_loop_gain = 5;
- else
- fll_div->fll_loop_gain = 0;
-
- if (Fref >= 48000)
- fll_div->fll_ref_freq = 0;
- else
- fll_div->fll_ref_freq = 1;
-
- /* Fvco should be 90-100MHz; don't check the upper bound */
- div = 2;
- while (Fout * div < 90000000) {
- div++;
- if (div > 64) {
- pr_err("Unable to find FLL_OUTDIV for Fout=%uHz\n",
- Fout);
- return -EINVAL;
- }
- }
- target = Fout * div;
- fll_div->fll_outdiv = div - 1;
-
- pr_debug("FLL Fvco=%dHz\n", target);
-
- /* Find an appropraite FLL_FRATIO and factor it out of the target */
- for (i = 0; i < ARRAY_SIZE(fll_fratios); i++) {
- if (fll_fratios[i].min <= Fref && Fref <= fll_fratios[i].max) {
- fll_div->fll_fratio = fll_fratios[i].fll_fratio;
- fratio = fll_fratios[i].ratio;
- break;
- }
- }
- if (i == ARRAY_SIZE(fll_fratios)) {
- pr_err("Unable to find FLL_FRATIO for Fref=%uHz\n", Fref);
- return -EINVAL;
- }
-
- fll_div->n = target / (fratio * Fref);
-
- if (target % Fref == 0) {
- fll_div->theta = 0;
- fll_div->lambda = 0;
- } else {
- gcd_fll = gcd(target, fratio * Fref);
-
- fll_div->theta = (target - (fll_div->n * fratio * Fref))
- / gcd_fll;
- fll_div->lambda = (fratio * Fref) / gcd_fll;
- }
-
- pr_debug("FLL N=%x THETA=%x LAMBDA=%x\n",
- fll_div->n, fll_div->theta, fll_div->lambda);
- pr_debug("FLL_FRATIO=%x FLL_OUTDIV=%x FLL_REFCLK_DIV=%x\n",
- fll_div->fll_fratio, fll_div->fll_outdiv,
- fll_div->fll_refclk_div);
-
- return 0;
-}
-
-static int wm8915_set_fll(struct snd_soc_codec *codec, int fll_id, int source,
- unsigned int Fref, unsigned int Fout)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct i2c_client *i2c = to_i2c_client(codec->dev);
- struct _fll_div fll_div;
- unsigned long timeout;
- int ret, reg;
-
- /* Any change? */
- if (source == wm8915->fll_src && Fref == wm8915->fll_fref &&
- Fout == wm8915->fll_fout)
- return 0;
-
- if (Fout == 0) {
- dev_dbg(codec->dev, "FLL disabled\n");
-
- wm8915->fll_fref = 0;
- wm8915->fll_fout = 0;
-
- snd_soc_update_bits(codec, WM8915_FLL_CONTROL_1,
- WM8915_FLL_ENA, 0);
-
- return 0;
- }
-
- ret = fll_factors(&fll_div, Fref, Fout);
- if (ret != 0)
- return ret;
-
- switch (source) {
- case WM8915_FLL_MCLK1:
- reg = 0;
- break;
- case WM8915_FLL_MCLK2:
- reg = 1;
- break;
- case WM8915_FLL_DACLRCLK1:
- reg = 2;
- break;
- case WM8915_FLL_BCLK1:
- reg = 3;
- break;
- default:
- dev_err(codec->dev, "Unknown FLL source %d\n", ret);
- return -EINVAL;
- }
-
- reg |= fll_div.fll_refclk_div << WM8915_FLL_REFCLK_DIV_SHIFT;
- reg |= fll_div.fll_ref_freq << WM8915_FLL_REF_FREQ_SHIFT;
-
- snd_soc_update_bits(codec, WM8915_FLL_CONTROL_5,
- WM8915_FLL_REFCLK_DIV_MASK | WM8915_FLL_REF_FREQ |
- WM8915_FLL_REFCLK_SRC_MASK, reg);
-
- reg = 0;
- if (fll_div.theta || fll_div.lambda)
- reg |= WM8915_FLL_EFS_ENA | (3 << WM8915_FLL_LFSR_SEL_SHIFT);
- else
- reg |= 1 << WM8915_FLL_LFSR_SEL_SHIFT;
- snd_soc_write(codec, WM8915_FLL_EFS_2, reg);
-
- snd_soc_update_bits(codec, WM8915_FLL_CONTROL_2,
- WM8915_FLL_OUTDIV_MASK |
- WM8915_FLL_FRATIO_MASK,
- (fll_div.fll_outdiv << WM8915_FLL_OUTDIV_SHIFT) |
- (fll_div.fll_fratio));
-
- snd_soc_write(codec, WM8915_FLL_CONTROL_3, fll_div.theta);
-
- snd_soc_update_bits(codec, WM8915_FLL_CONTROL_4,
- WM8915_FLL_N_MASK | WM8915_FLL_LOOP_GAIN_MASK,
- (fll_div.n << WM8915_FLL_N_SHIFT) |
- fll_div.fll_loop_gain);
-
- snd_soc_write(codec, WM8915_FLL_EFS_1, fll_div.lambda);
-
- snd_soc_update_bits(codec, WM8915_FLL_CONTROL_1,
- WM8915_FLL_ENA, WM8915_FLL_ENA);
-
- /* The FLL supports live reconfiguration - kick that in case we were
- * already enabled.
- */
- snd_soc_write(codec, WM8915_FLL_CONTROL_6, WM8915_FLL_SWITCH_CLK);
-
- /* Wait for the FLL to lock, using the interrupt if possible */
- if (Fref > 1000000)
- timeout = usecs_to_jiffies(300);
- else
- timeout = msecs_to_jiffies(2);
-
- /* Allow substantially longer if we've actually got the IRQ */
- if (i2c->irq)
- timeout *= 1000;
-
- ret = wait_for_completion_timeout(&wm8915->fll_lock, timeout);
-
- if (ret == 0 && i2c->irq) {
- dev_err(codec->dev, "Timed out waiting for FLL\n");
- ret = -ETIMEDOUT;
- } else {
- ret = 0;
- }
-
- dev_dbg(codec->dev, "FLL configured for %dHz->%dHz\n", Fref, Fout);
-
- wm8915->fll_fref = Fref;
- wm8915->fll_fout = Fout;
- wm8915->fll_src = source;
-
- return ret;
-}
-
-#ifdef CONFIG_GPIOLIB
-static inline struct wm8915_priv *gpio_to_wm8915(struct gpio_chip *chip)
-{
- return container_of(chip, struct wm8915_priv, gpio_chip);
-}
-
-static void wm8915_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- struct wm8915_priv *wm8915 = gpio_to_wm8915(chip);
- struct snd_soc_codec *codec = wm8915->codec;
-
- snd_soc_update_bits(codec, WM8915_GPIO_1 + offset,
- WM8915_GP1_LVL, !!value << WM8915_GP1_LVL_SHIFT);
-}
-
-static int wm8915_gpio_direction_out(struct gpio_chip *chip,
- unsigned offset, int value)
-{
- struct wm8915_priv *wm8915 = gpio_to_wm8915(chip);
- struct snd_soc_codec *codec = wm8915->codec;
- int val;
-
- val = (1 << WM8915_GP1_FN_SHIFT) | (!!value << WM8915_GP1_LVL_SHIFT);
-
- return snd_soc_update_bits(codec, WM8915_GPIO_1 + offset,
- WM8915_GP1_FN_MASK | WM8915_GP1_DIR |
- WM8915_GP1_LVL, val);
-}
-
-static int wm8915_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
- struct wm8915_priv *wm8915 = gpio_to_wm8915(chip);
- struct snd_soc_codec *codec = wm8915->codec;
- int ret;
-
- ret = snd_soc_read(codec, WM8915_GPIO_1 + offset);
- if (ret < 0)
- return ret;
-
- return (ret & WM8915_GP1_LVL) != 0;
-}
-
-static int wm8915_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
-{
- struct wm8915_priv *wm8915 = gpio_to_wm8915(chip);
- struct snd_soc_codec *codec = wm8915->codec;
-
- return snd_soc_update_bits(codec, WM8915_GPIO_1 + offset,
- WM8915_GP1_FN_MASK | WM8915_GP1_DIR,
- (1 << WM8915_GP1_FN_SHIFT) |
- (1 << WM8915_GP1_DIR_SHIFT));
-}
-
-static struct gpio_chip wm8915_template_chip = {
- .label = "wm8915",
- .owner = THIS_MODULE,
- .direction_output = wm8915_gpio_direction_out,
- .set = wm8915_gpio_set,
- .direction_input = wm8915_gpio_direction_in,
- .get = wm8915_gpio_get,
- .can_sleep = 1,
-};
-
-static void wm8915_init_gpio(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int ret;
-
- wm8915->gpio_chip = wm8915_template_chip;
- wm8915->gpio_chip.ngpio = 5;
- wm8915->gpio_chip.dev = codec->dev;
-
- if (wm8915->pdata.gpio_base)
- wm8915->gpio_chip.base = wm8915->pdata.gpio_base;
- else
- wm8915->gpio_chip.base = -1;
-
- ret = gpiochip_add(&wm8915->gpio_chip);
- if (ret != 0)
- dev_err(codec->dev, "Failed to add GPIOs: %d\n", ret);
-}
-
-static void wm8915_free_gpio(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int ret;
-
- ret = gpiochip_remove(&wm8915->gpio_chip);
- if (ret != 0)
- dev_err(codec->dev, "Failed to remove GPIOs: %d\n", ret);
-}
-#else
-static void wm8915_init_gpio(struct snd_soc_codec *codec)
-{
-}
-
-static void wm8915_free_gpio(struct snd_soc_codec *codec)
-{
-}
-#endif
-
-/**
- * wm8915_detect - Enable default WM8915 jack detection
- *
- * The WM8915 has advanced accessory detection support for headsets.
- * This function provides a default implementation which integrates
- * the majority of this functionality with minimal user configuration.
- *
- * This will detect headset, headphone and short circuit button and
- * will also detect inverted microphone ground connections and update
- * the polarity of the connections.
- */
-int wm8915_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack,
- wm8915_polarity_fn polarity_cb)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
-
- wm8915->jack = jack;
- wm8915->detecting = true;
- wm8915->polarity_cb = polarity_cb;
-
- if (wm8915->polarity_cb)
- wm8915->polarity_cb(codec, 0);
-
- /* Clear discarge to avoid noise during detection */
- snd_soc_update_bits(codec, WM8915_MICBIAS_1,
- WM8915_MICB1_DISCH, 0);
- snd_soc_update_bits(codec, WM8915_MICBIAS_2,
- WM8915_MICB2_DISCH, 0);
-
- /* LDO2 powers the microphones, SYSCLK clocks detection */
- snd_soc_dapm_force_enable_pin(&codec->dapm, "LDO2");
- snd_soc_dapm_force_enable_pin(&codec->dapm, "SYSCLK");
-
- /* We start off just enabling microphone detection - even a
- * plain headphone will trigger detection.
- */
- snd_soc_update_bits(codec, WM8915_MIC_DETECT_1,
- WM8915_MICD_ENA, WM8915_MICD_ENA);
-
- /* Slowest detection rate, gives debounce for initial detection */
- snd_soc_update_bits(codec, WM8915_MIC_DETECT_1,
- WM8915_MICD_RATE_MASK,
- WM8915_MICD_RATE_MASK);
-
- /* Enable interrupts and we're off */
- snd_soc_update_bits(codec, WM8915_INTERRUPT_STATUS_2_MASK,
- WM8915_IM_MICD_EINT, 0);
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(wm8915_detect);
-
-static void wm8915_micd(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int val, reg;
-
- val = snd_soc_read(codec, WM8915_MIC_DETECT_3);
-
- dev_dbg(codec->dev, "Microphone event: %x\n", val);
-
- if (!(val & WM8915_MICD_VALID)) {
- dev_warn(codec->dev, "Microphone detection state invalid\n");
- return;
- }
-
- /* No accessory, reset everything and report removal */
- if (!(val & WM8915_MICD_STS)) {
- dev_dbg(codec->dev, "Jack removal detected\n");
- wm8915->jack_mic = false;
- wm8915->detecting = true;
- snd_soc_jack_report(wm8915->jack, 0,
- SND_JACK_HEADSET | SND_JACK_BTN_0);
- snd_soc_update_bits(codec, WM8915_MIC_DETECT_1,
- WM8915_MICD_RATE_MASK,
- WM8915_MICD_RATE_MASK);
- return;
- }
-
- /* If the measurement is very high we've got a microphone but
- * do a little debounce to account for mechanical issues.
- */
- if (val & 0x400) {
- dev_dbg(codec->dev, "Microphone detected\n");
- snd_soc_jack_report(wm8915->jack, SND_JACK_HEADSET,
- SND_JACK_HEADSET | SND_JACK_BTN_0);
- wm8915->jack_mic = true;
- wm8915->detecting = false;
-
- /* Increase poll rate to give better responsiveness
- * for buttons */
- snd_soc_update_bits(codec, WM8915_MIC_DETECT_1,
- WM8915_MICD_RATE_MASK,
- 5 << WM8915_MICD_RATE_SHIFT);
- }
-
- /* If we detected a lower impedence during initial startup
- * then we probably have the wrong polarity, flip it. Don't
- * do this for the lowest impedences to speed up detection of
- * plain headphones.
- */
- if (wm8915->detecting && (val & 0x3f0)) {
- reg = snd_soc_read(codec, WM8915_ACCESSORY_DETECT_MODE_2);
- reg ^= WM8915_HPOUT1FB_SRC | WM8915_MICD_SRC |
- WM8915_MICD_BIAS_SRC;
- snd_soc_update_bits(codec, WM8915_ACCESSORY_DETECT_MODE_2,
- WM8915_HPOUT1FB_SRC | WM8915_MICD_SRC |
- WM8915_MICD_BIAS_SRC, reg);
-
- if (wm8915->polarity_cb)
- wm8915->polarity_cb(codec,
- (reg & WM8915_MICD_SRC) != 0);
-
- dev_dbg(codec->dev, "Set microphone polarity to %d\n",
- (reg & WM8915_MICD_SRC) != 0);
-
- return;
- }
-
- /* Don't distinguish between buttons, just report any low
- * impedence as BTN_0.
- */
- if (val & 0x3fc) {
- if (wm8915->jack_mic) {
- dev_dbg(codec->dev, "Mic button detected\n");
- snd_soc_jack_report(wm8915->jack,
- SND_JACK_HEADSET | SND_JACK_BTN_0,
- SND_JACK_HEADSET | SND_JACK_BTN_0);
- } else {
- dev_dbg(codec->dev, "Headphone detected\n");
- snd_soc_jack_report(wm8915->jack,
- SND_JACK_HEADPHONE,
- SND_JACK_HEADSET |
- SND_JACK_BTN_0);
-
- /* Increase the detection rate a bit for
- * responsiveness.
- */
- snd_soc_update_bits(codec, WM8915_MIC_DETECT_1,
- WM8915_MICD_RATE_MASK,
- 7 << WM8915_MICD_RATE_SHIFT);
-
- wm8915->detecting = false;
- }
- }
-}
-
-static irqreturn_t wm8915_irq(int irq, void *data)
-{
- struct snd_soc_codec *codec = data;
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- int irq_val;
-
- irq_val = snd_soc_read(codec, WM8915_INTERRUPT_STATUS_2);
- if (irq_val < 0) {
- dev_err(codec->dev, "Failed to read IRQ status: %d\n",
- irq_val);
- return IRQ_NONE;
- }
- irq_val &= ~snd_soc_read(codec, WM8915_INTERRUPT_STATUS_2_MASK);
-
- if (irq_val & (WM8915_DCS_DONE_01_EINT | WM8915_DCS_DONE_23_EINT)) {
- dev_dbg(codec->dev, "DC servo IRQ\n");
- complete(&wm8915->dcs_done);
- }
-
- if (irq_val & WM8915_FIFOS_ERR_EINT)
- dev_err(codec->dev, "Digital core FIFO error\n");
-
- if (irq_val & WM8915_FLL_LOCK_EINT) {
- dev_dbg(codec->dev, "FLL locked\n");
- complete(&wm8915->fll_lock);
- }
-
- if (irq_val & WM8915_MICD_EINT)
- wm8915_micd(codec);
-
- if (irq_val) {
- snd_soc_write(codec, WM8915_INTERRUPT_STATUS_2, irq_val);
-
- return IRQ_HANDLED;
- } else {
- return IRQ_NONE;
- }
-}
-
-static irqreturn_t wm8915_edge_irq(int irq, void *data)
-{
- irqreturn_t ret = IRQ_NONE;
- irqreturn_t val;
-
- do {
- val = wm8915_irq(irq, data);
- if (val != IRQ_NONE)
- ret = val;
- } while (val != IRQ_NONE);
-
- return ret;
-}
-
-static void wm8915_retune_mobile_pdata(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct wm8915_pdata *pdata = &wm8915->pdata;
-
- struct snd_kcontrol_new controls[] = {
- SOC_ENUM_EXT("DSP1 EQ Mode",
- wm8915->retune_mobile_enum,
- wm8915_get_retune_mobile_enum,
- wm8915_put_retune_mobile_enum),
- SOC_ENUM_EXT("DSP2 EQ Mode",
- wm8915->retune_mobile_enum,
- wm8915_get_retune_mobile_enum,
- wm8915_put_retune_mobile_enum),
- };
- int ret, i, j;
- const char **t;
-
- /* We need an array of texts for the enum API but the number
- * of texts is likely to be less than the number of
- * configurations due to the sample rate dependency of the
- * configurations. */
- wm8915->num_retune_mobile_texts = 0;
- wm8915->retune_mobile_texts = NULL;
- for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
- for (j = 0; j < wm8915->num_retune_mobile_texts; j++) {
- if (strcmp(pdata->retune_mobile_cfgs[i].name,
- wm8915->retune_mobile_texts[j]) == 0)
- break;
- }
-
- if (j != wm8915->num_retune_mobile_texts)
- continue;
-
- /* Expand the array... */
- t = krealloc(wm8915->retune_mobile_texts,
- sizeof(char *) *
- (wm8915->num_retune_mobile_texts + 1),
- GFP_KERNEL);
- if (t == NULL)
- continue;
-
- /* ...store the new entry... */
- t[wm8915->num_retune_mobile_texts] =
- pdata->retune_mobile_cfgs[i].name;
-
- /* ...and remember the new version. */
- wm8915->num_retune_mobile_texts++;
- wm8915->retune_mobile_texts = t;
- }
-
- dev_dbg(codec->dev, "Allocated %d unique ReTune Mobile names\n",
- wm8915->num_retune_mobile_texts);
-
- wm8915->retune_mobile_enum.max = wm8915->num_retune_mobile_texts;
- wm8915->retune_mobile_enum.texts = wm8915->retune_mobile_texts;
-
- ret = snd_soc_add_controls(codec, controls, ARRAY_SIZE(controls));
- if (ret != 0)
- dev_err(codec->dev,
- "Failed to add ReTune Mobile controls: %d\n", ret);
-}
-
-static int wm8915_probe(struct snd_soc_codec *codec)
-{
- int ret;
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct i2c_client *i2c = to_i2c_client(codec->dev);
- struct snd_soc_dapm_context *dapm = &codec->dapm;
- int i, irq_flags;
-
- wm8915->codec = codec;
-
- init_completion(&wm8915->dcs_done);
- init_completion(&wm8915->fll_lock);
-
- dapm->idle_bias_off = true;
- dapm->bias_level = SND_SOC_BIAS_OFF;
-
- ret = snd_soc_codec_set_cache_io(codec, 16, 16, SND_SOC_I2C);
- if (ret != 0) {
- dev_err(codec->dev, "Failed to set cache I/O: %d\n", ret);
- goto err;
- }
-
- for (i = 0; i < ARRAY_SIZE(wm8915->supplies); i++)
- wm8915->supplies[i].supply = wm8915_supply_names[i];
-
- ret = regulator_bulk_get(codec->dev, ARRAY_SIZE(wm8915->supplies),
- wm8915->supplies);
- if (ret != 0) {
- dev_err(codec->dev, "Failed to request supplies: %d\n", ret);
- goto err;
- }
-
- wm8915->disable_nb[0].notifier_call = wm8915_regulator_event_0;
- wm8915->disable_nb[1].notifier_call = wm8915_regulator_event_1;
- wm8915->disable_nb[2].notifier_call = wm8915_regulator_event_2;
- wm8915->disable_nb[3].notifier_call = wm8915_regulator_event_3;
-
- /* This should really be moved into the regulator core */
- for (i = 0; i < ARRAY_SIZE(wm8915->supplies); i++) {
- ret = regulator_register_notifier(wm8915->supplies[i].consumer,
- &wm8915->disable_nb[i]);
- if (ret != 0) {
- dev_err(codec->dev,
- "Failed to register regulator notifier: %d\n",
- ret);
- }
- }
-
- ret = regulator_bulk_enable(ARRAY_SIZE(wm8915->supplies),
- wm8915->supplies);
- if (ret != 0) {
- dev_err(codec->dev, "Failed to enable supplies: %d\n", ret);
- goto err_get;
- }
-
- if (wm8915->pdata.ldo_ena >= 0) {
- gpio_set_value_cansleep(wm8915->pdata.ldo_ena, 1);
- msleep(5);
- }
-
- ret = snd_soc_read(codec, WM8915_SOFTWARE_RESET);
- if (ret < 0) {
- dev_err(codec->dev, "Failed to read ID register: %d\n", ret);
- goto err_enable;
- }
- if (ret != 0x8915) {
- dev_err(codec->dev, "Device is not a WM8915, ID %x\n", ret);
- ret = -EINVAL;
- goto err_enable;
- }
-
- ret = snd_soc_read(codec, WM8915_CHIP_REVISION);
- if (ret < 0) {
- dev_err(codec->dev, "Failed to read device revision: %d\n",
- ret);
- goto err_enable;
- }
-
- dev_info(codec->dev, "revision %c\n",
- (ret & WM8915_CHIP_REV_MASK) + 'A');
-
- if (wm8915->pdata.ldo_ena >= 0) {
- gpio_set_value_cansleep(wm8915->pdata.ldo_ena, 0);
- } else {
- ret = wm8915_reset(codec);
- if (ret < 0) {
- dev_err(codec->dev, "Failed to issue reset\n");
- goto err_enable;
- }
- }
-
- codec->cache_only = true;
-
- /* Apply platform data settings */
- snd_soc_update_bits(codec, WM8915_LINE_INPUT_CONTROL,
- WM8915_INL_MODE_MASK | WM8915_INR_MODE_MASK,
- wm8915->pdata.inl_mode << WM8915_INL_MODE_SHIFT |
- wm8915->pdata.inr_mode);
-
- for (i = 0; i < ARRAY_SIZE(wm8915->pdata.gpio_default); i++) {
- if (!wm8915->pdata.gpio_default[i])
- continue;
-
- snd_soc_write(codec, WM8915_GPIO_1 + i,
- wm8915->pdata.gpio_default[i] & 0xffff);
- }
-
- if (wm8915->pdata.spkmute_seq)
- snd_soc_update_bits(codec, WM8915_PDM_SPEAKER_MUTE_SEQUENCE,
- WM8915_SPK_MUTE_ENDIAN |
- WM8915_SPK_MUTE_SEQ1_MASK,
- wm8915->pdata.spkmute_seq);
-
- snd_soc_update_bits(codec, WM8915_ACCESSORY_DETECT_MODE_2,
- WM8915_MICD_BIAS_SRC | WM8915_HPOUT1FB_SRC |
- WM8915_MICD_SRC, wm8915->pdata.micdet_def);
-
- /* Latch volume update bits */
- snd_soc_update_bits(codec, WM8915_LEFT_LINE_INPUT_VOLUME,
- WM8915_IN1_VU, WM8915_IN1_VU);
- snd_soc_update_bits(codec, WM8915_RIGHT_LINE_INPUT_VOLUME,
- WM8915_IN1_VU, WM8915_IN1_VU);
-
- snd_soc_update_bits(codec, WM8915_DAC1_LEFT_VOLUME,
- WM8915_DAC1_VU, WM8915_DAC1_VU);
- snd_soc_update_bits(codec, WM8915_DAC1_RIGHT_VOLUME,
- WM8915_DAC1_VU, WM8915_DAC1_VU);
- snd_soc_update_bits(codec, WM8915_DAC2_LEFT_VOLUME,
- WM8915_DAC2_VU, WM8915_DAC2_VU);
- snd_soc_update_bits(codec, WM8915_DAC2_RIGHT_VOLUME,
- WM8915_DAC2_VU, WM8915_DAC2_VU);
-
- snd_soc_update_bits(codec, WM8915_OUTPUT1_LEFT_VOLUME,
- WM8915_DAC1_VU, WM8915_DAC1_VU);
- snd_soc_update_bits(codec, WM8915_OUTPUT1_RIGHT_VOLUME,
- WM8915_DAC1_VU, WM8915_DAC1_VU);
- snd_soc_update_bits(codec, WM8915_OUTPUT2_LEFT_VOLUME,
- WM8915_DAC2_VU, WM8915_DAC2_VU);
- snd_soc_update_bits(codec, WM8915_OUTPUT2_RIGHT_VOLUME,
- WM8915_DAC2_VU, WM8915_DAC2_VU);
-
- snd_soc_update_bits(codec, WM8915_DSP1_TX_LEFT_VOLUME,
- WM8915_DSP1TX_VU, WM8915_DSP1TX_VU);
- snd_soc_update_bits(codec, WM8915_DSP1_TX_RIGHT_VOLUME,
- WM8915_DSP1TX_VU, WM8915_DSP1TX_VU);
- snd_soc_update_bits(codec, WM8915_DSP2_TX_LEFT_VOLUME,
- WM8915_DSP2TX_VU, WM8915_DSP2TX_VU);
- snd_soc_update_bits(codec, WM8915_DSP2_TX_RIGHT_VOLUME,
- WM8915_DSP2TX_VU, WM8915_DSP2TX_VU);
-
- snd_soc_update_bits(codec, WM8915_DSP1_RX_LEFT_VOLUME,
- WM8915_DSP1RX_VU, WM8915_DSP1RX_VU);
- snd_soc_update_bits(codec, WM8915_DSP1_RX_RIGHT_VOLUME,
- WM8915_DSP1RX_VU, WM8915_DSP1RX_VU);
- snd_soc_update_bits(codec, WM8915_DSP2_RX_LEFT_VOLUME,
- WM8915_DSP2RX_VU, WM8915_DSP2RX_VU);
- snd_soc_update_bits(codec, WM8915_DSP2_RX_RIGHT_VOLUME,
- WM8915_DSP2RX_VU, WM8915_DSP2RX_VU);
-
- /* No support currently for the underclocked TDM modes and
- * pick a default TDM layout with each channel pair working with
- * slots 0 and 1. */
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_0_CONFIGURATION,
- WM8915_AIF1RX_CHAN0_SLOTS_MASK |
- WM8915_AIF1RX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN0_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_1_CONFIGURATION,
- WM8915_AIF1RX_CHAN1_SLOTS_MASK |
- WM8915_AIF1RX_CHAN1_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN1_SLOTS_SHIFT | 1);
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_2_CONFIGURATION,
- WM8915_AIF1RX_CHAN2_SLOTS_MASK |
- WM8915_AIF1RX_CHAN2_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN2_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_3_CONFIGURATION,
- WM8915_AIF1RX_CHAN3_SLOTS_MASK |
- WM8915_AIF1RX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN3_SLOTS_SHIFT | 1);
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_4_CONFIGURATION,
- WM8915_AIF1RX_CHAN4_SLOTS_MASK |
- WM8915_AIF1RX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN4_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1RX_CHANNEL_5_CONFIGURATION,
- WM8915_AIF1RX_CHAN5_SLOTS_MASK |
- WM8915_AIF1RX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1RX_CHAN5_SLOTS_SHIFT | 1);
-
- snd_soc_update_bits(codec, WM8915_AIF2RX_CHANNEL_0_CONFIGURATION,
- WM8915_AIF2RX_CHAN0_SLOTS_MASK |
- WM8915_AIF2RX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF2RX_CHAN0_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF2RX_CHANNEL_1_CONFIGURATION,
- WM8915_AIF2RX_CHAN1_SLOTS_MASK |
- WM8915_AIF2RX_CHAN1_START_SLOT_MASK,
- 1 << WM8915_AIF2RX_CHAN1_SLOTS_SHIFT | 1);
-
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_0_CONFIGURATION,
- WM8915_AIF1TX_CHAN0_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN0_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_1_CONFIGURATION,
- WM8915_AIF1TX_CHAN1_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN1_SLOTS_SHIFT | 1);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_2_CONFIGURATION,
- WM8915_AIF1TX_CHAN2_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN2_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_3_CONFIGURATION,
- WM8915_AIF1TX_CHAN3_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN3_SLOTS_SHIFT | 1);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_4_CONFIGURATION,
- WM8915_AIF1TX_CHAN4_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN4_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_5_CONFIGURATION,
- WM8915_AIF1TX_CHAN5_SLOTS_MASK |
- WM8915_AIF1TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN5_SLOTS_SHIFT | 1);
-
- snd_soc_update_bits(codec, WM8915_AIF2TX_CHANNEL_0_CONFIGURATION,
- WM8915_AIF2TX_CHAN0_SLOTS_MASK |
- WM8915_AIF2TX_CHAN0_START_SLOT_MASK,
- 1 << WM8915_AIF2TX_CHAN0_SLOTS_SHIFT | 0);
- snd_soc_update_bits(codec, WM8915_AIF1TX_CHANNEL_1_CONFIGURATION,
- WM8915_AIF2TX_CHAN1_SLOTS_MASK |
- WM8915_AIF2TX_CHAN1_START_SLOT_MASK,
- 1 << WM8915_AIF1TX_CHAN1_SLOTS_SHIFT | 1);
-
- if (wm8915->pdata.num_retune_mobile_cfgs)
- wm8915_retune_mobile_pdata(codec);
- else
- snd_soc_add_controls(codec, wm8915_eq_controls,
- ARRAY_SIZE(wm8915_eq_controls));
-
- /* If the TX LRCLK pins are not in LRCLK mode configure the
- * AIFs to source their clocks from the RX LRCLKs.
- */
- if ((snd_soc_read(codec, WM8915_GPIO_1)))
- snd_soc_update_bits(codec, WM8915_AIF1_TX_LRCLK_2,
- WM8915_AIF1TX_LRCLK_MODE,
- WM8915_AIF1TX_LRCLK_MODE);
-
- if ((snd_soc_read(codec, WM8915_GPIO_2)))
- snd_soc_update_bits(codec, WM8915_AIF2_TX_LRCLK_2,
- WM8915_AIF2TX_LRCLK_MODE,
- WM8915_AIF2TX_LRCLK_MODE);
-
- regulator_bulk_disable(ARRAY_SIZE(wm8915->supplies), wm8915->supplies);
-
- wm8915_init_gpio(codec);
-
- if (i2c->irq) {
- if (wm8915->pdata.irq_flags)
- irq_flags = wm8915->pdata.irq_flags;
- else
- irq_flags = IRQF_TRIGGER_LOW;
-
- irq_flags |= IRQF_ONESHOT;
-
- if (irq_flags & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING))
- ret = request_threaded_irq(i2c->irq, NULL,
- wm8915_edge_irq,
- irq_flags, "wm8915", codec);
- else
- ret = request_threaded_irq(i2c->irq, NULL, wm8915_irq,
- irq_flags, "wm8915", codec);
-
- if (ret == 0) {
- /* Unmask the interrupt */
- snd_soc_update_bits(codec, WM8915_INTERRUPT_CONTROL,
- WM8915_IM_IRQ, 0);
-
- /* Enable error reporting and DC servo status */
- snd_soc_update_bits(codec,
- WM8915_INTERRUPT_STATUS_2_MASK,
- WM8915_IM_DCS_DONE_23_EINT |
- WM8915_IM_DCS_DONE_01_EINT |
- WM8915_IM_FLL_LOCK_EINT |
- WM8915_IM_FIFOS_ERR_EINT,
- 0);
- } else {
- dev_err(codec->dev, "Failed to request IRQ: %d\n",
- ret);
- }
- }
-
- return 0;
-
-err_enable:
- if (wm8915->pdata.ldo_ena >= 0)
- gpio_set_value_cansleep(wm8915->pdata.ldo_ena, 0);
-
- regulator_bulk_disable(ARRAY_SIZE(wm8915->supplies), wm8915->supplies);
-err_get:
- regulator_bulk_free(ARRAY_SIZE(wm8915->supplies), wm8915->supplies);
-err:
- return ret;
-}
-
-static int wm8915_remove(struct snd_soc_codec *codec)
-{
- struct wm8915_priv *wm8915 = snd_soc_codec_get_drvdata(codec);
- struct i2c_client *i2c = to_i2c_client(codec->dev);
- int i;
-
- snd_soc_update_bits(codec, WM8915_INTERRUPT_CONTROL,
- WM8915_IM_IRQ, WM8915_IM_IRQ);
-
- if (i2c->irq)
- free_irq(i2c->irq, codec);
-
- wm8915_free_gpio(codec);
-
- for (i = 0; i < ARRAY_SIZE(wm8915->supplies); i++)
- regulator_unregister_notifier(wm8915->supplies[i].consumer,
- &wm8915->disable_nb[i]);
- regulator_bulk_free(ARRAY_SIZE(wm8915->supplies), wm8915->supplies);
-
- return 0;
-}
-
-static struct snd_soc_codec_driver soc_codec_dev_wm8915 = {
- .probe = wm8915_probe,
- .remove = wm8915_remove,
- .set_bias_level = wm8915_set_bias_level,
- .seq_notifier = wm8915_seq_notifier,
- .reg_cache_size = WM8915_MAX_REGISTER + 1,
- .reg_word_size = sizeof(u16),
- .reg_cache_default = wm8915_reg,
- .volatile_register = wm8915_volatile_register,
- .readable_register = wm8915_readable_register,
- .compress_type = SND_SOC_RBTREE_COMPRESSION,
- .controls = wm8915_snd_controls,
- .num_controls = ARRAY_SIZE(wm8915_snd_controls),
- .dapm_widgets = wm8915_dapm_widgets,
- .num_dapm_widgets = ARRAY_SIZE(wm8915_dapm_widgets),
- .dapm_routes = wm8915_dapm_routes,
- .num_dapm_routes = ARRAY_SIZE(wm8915_dapm_routes),
- .set_pll = wm8915_set_fll,
-};
-
-#define WM8915_RATES (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\
- SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_48000)
-#define WM8915_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE |\
- SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S24_LE |\
- SNDRV_PCM_FMTBIT_S32_LE)
-
-static struct snd_soc_dai_ops wm8915_dai_ops = {
- .set_fmt = wm8915_set_fmt,
- .hw_params = wm8915_hw_params,
- .set_sysclk = wm8915_set_sysclk,
-};
-
-static struct snd_soc_dai_driver wm8915_dai[] = {
- {
- .name = "wm8915-aif1",
- .playback = {
- .stream_name = "AIF1 Playback",
- .channels_min = 1,
- .channels_max = 6,
- .rates = WM8915_RATES,
- .formats = WM8915_FORMATS,
- },
- .capture = {
- .stream_name = "AIF1 Capture",
- .channels_min = 1,
- .channels_max = 6,
- .rates = WM8915_RATES,
- .formats = WM8915_FORMATS,
- },
- .ops = &wm8915_dai_ops,
- },
- {
- .name = "wm8915-aif2",
- .playback = {
- .stream_name = "AIF2 Playback",
- .channels_min = 1,
- .channels_max = 2,
- .rates = WM8915_RATES,
- .formats = WM8915_FORMATS,
- },
- .capture = {
- .stream_name = "AIF2 Capture",
- .channels_min = 1,
- .channels_max = 2,
- .rates = WM8915_RATES,
- .formats = WM8915_FORMATS,
- },
- .ops = &wm8915_dai_ops,
- },
-};
-
-static __devinit int wm8915_i2c_probe(struct i2c_client *i2c,
- const struct i2c_device_id *id)
-{
- struct wm8915_priv *wm8915;
- int ret;
-
- wm8915 = kzalloc(sizeof(struct wm8915_priv), GFP_KERNEL);
- if (wm8915 == NULL)
- return -ENOMEM;
-
- i2c_set_clientdata(i2c, wm8915);
-
- if (dev_get_platdata(&i2c->dev))
- memcpy(&wm8915->pdata, dev_get_platdata(&i2c->dev),
- sizeof(wm8915->pdata));
-
- if (wm8915->pdata.ldo_ena > 0) {
- ret = gpio_request_one(wm8915->pdata.ldo_ena,
- GPIOF_OUT_INIT_LOW, "WM8915 ENA");
- if (ret < 0) {
- dev_err(&i2c->dev, "Failed to request GPIO %d: %d\n",
- wm8915->pdata.ldo_ena, ret);
- goto err;
- }
- }
-
- ret = snd_soc_register_codec(&i2c->dev,
- &soc_codec_dev_wm8915, wm8915_dai,
- ARRAY_SIZE(wm8915_dai));
- if (ret < 0)
- goto err_gpio;
-
- return ret;
-
-err_gpio:
- if (wm8915->pdata.ldo_ena > 0)
- gpio_free(wm8915->pdata.ldo_ena);
-err:
- kfree(wm8915);
-
- return ret;
-}
-
-static __devexit int wm8915_i2c_remove(struct i2c_client *client)
-{
- struct wm8915_priv *wm8915 = i2c_get_clientdata(client);
-
- snd_soc_unregister_codec(&client->dev);
- if (wm8915->pdata.ldo_ena > 0)
- gpio_free(wm8915->pdata.ldo_ena);
- kfree(i2c_get_clientdata(client));
- return 0;
-}
-
-static const struct i2c_device_id wm8915_i2c_id[] = {
- { "wm8915", 0 },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, wm8915_i2c_id);
-
-static struct i2c_driver wm8915_i2c_driver = {
- .driver = {
- .name = "wm8915",
- .owner = THIS_MODULE,
- },
- .probe = wm8915_i2c_probe,
- .remove = __devexit_p(wm8915_i2c_remove),
- .id_table = wm8915_i2c_id,
-};
-
-static int __init wm8915_modinit(void)
-{
- int ret;
-
- ret = i2c_add_driver(&wm8915_i2c_driver);
- if (ret != 0) {
- printk(KERN_ERR "Failed to register WM8915 I2C driver: %d\n",
- ret);
- }
-
- return ret;
-}
-module_init(wm8915_modinit);
-
-static void __exit wm8915_exit(void)
-{
- i2c_del_driver(&wm8915_i2c_driver);
-}
-module_exit(wm8915_exit);
-
-MODULE_DESCRIPTION("ASoC WM8915 driver");
-MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
-MODULE_LICENSE("GPL");
+++ /dev/null
-/*
- * wm8915.h - WM8915 audio codec interface
- *
- * Copyright 2011 Wolfson Microelectronics PLC.
- * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef _WM8915_H
-#define _WM8915_H
-
-#define WM8915_SYSCLK_MCLK1 1
-#define WM8915_SYSCLK_MCLK2 2
-#define WM8915_SYSCLK_FLL 3
-
-#define WM8915_FLL_MCLK1 1
-#define WM8915_FLL_MCLK2 2
-#define WM8915_FLL_DACLRCLK1 3
-#define WM8915_FLL_BCLK1 4
-
-typedef void (*wm8915_polarity_fn)(struct snd_soc_codec *codec, int polarity);
-
-int wm8915_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack,
- wm8915_polarity_fn polarity_cb);
-
-/*
- * Register values.
- */
-#define WM8915_SOFTWARE_RESET 0x00
-#define WM8915_POWER_MANAGEMENT_1 0x01
-#define WM8915_POWER_MANAGEMENT_2 0x02
-#define WM8915_POWER_MANAGEMENT_3 0x03
-#define WM8915_POWER_MANAGEMENT_4 0x04
-#define WM8915_POWER_MANAGEMENT_5 0x05
-#define WM8915_POWER_MANAGEMENT_6 0x06
-#define WM8915_POWER_MANAGEMENT_7 0x07
-#define WM8915_POWER_MANAGEMENT_8 0x08
-#define WM8915_LEFT_LINE_INPUT_VOLUME 0x10
-#define WM8915_RIGHT_LINE_INPUT_VOLUME 0x11
-#define WM8915_LINE_INPUT_CONTROL 0x12
-#define WM8915_DAC1_HPOUT1_VOLUME 0x15
-#define WM8915_DAC2_HPOUT2_VOLUME 0x16
-#define WM8915_DAC1_LEFT_VOLUME 0x18
-#define WM8915_DAC1_RIGHT_VOLUME 0x19
-#define WM8915_DAC2_LEFT_VOLUME 0x1A
-#define WM8915_DAC2_RIGHT_VOLUME 0x1B
-#define WM8915_OUTPUT1_LEFT_VOLUME 0x1C
-#define WM8915_OUTPUT1_RIGHT_VOLUME 0x1D
-#define WM8915_OUTPUT2_LEFT_VOLUME 0x1E
-#define WM8915_OUTPUT2_RIGHT_VOLUME 0x1F
-#define WM8915_MICBIAS_1 0x20
-#define WM8915_MICBIAS_2 0x21
-#define WM8915_LDO_1 0x28
-#define WM8915_LDO_2 0x29
-#define WM8915_ACCESSORY_DETECT_MODE_1 0x30
-#define WM8915_ACCESSORY_DETECT_MODE_2 0x31
-#define WM8915_HEADPHONE_DETECT_1 0x34
-#define WM8915_HEADPHONE_DETECT_2 0x35
-#define WM8915_MIC_DETECT_1 0x38
-#define WM8915_MIC_DETECT_2 0x39
-#define WM8915_MIC_DETECT_3 0x3A
-#define WM8915_CHARGE_PUMP_1 0x40
-#define WM8915_CHARGE_PUMP_2 0x41
-#define WM8915_DC_SERVO_1 0x50
-#define WM8915_DC_SERVO_2 0x51
-#define WM8915_DC_SERVO_3 0x52
-#define WM8915_DC_SERVO_5 0x54
-#define WM8915_DC_SERVO_6 0x55
-#define WM8915_DC_SERVO_7 0x56
-#define WM8915_DC_SERVO_READBACK_0 0x57
-#define WM8915_ANALOGUE_HP_1 0x60
-#define WM8915_ANALOGUE_HP_2 0x61
-#define WM8915_CHIP_REVISION 0x100
-#define WM8915_CONTROL_INTERFACE_1 0x101
-#define WM8915_WRITE_SEQUENCER_CTRL_1 0x110
-#define WM8915_WRITE_SEQUENCER_CTRL_2 0x111
-#define WM8915_AIF_CLOCKING_1 0x200
-#define WM8915_AIF_CLOCKING_2 0x201
-#define WM8915_CLOCKING_1 0x208
-#define WM8915_CLOCKING_2 0x209
-#define WM8915_AIF_RATE 0x210
-#define WM8915_FLL_CONTROL_1 0x220
-#define WM8915_FLL_CONTROL_2 0x221
-#define WM8915_FLL_CONTROL_3 0x222
-#define WM8915_FLL_CONTROL_4 0x223
-#define WM8915_FLL_CONTROL_5 0x224
-#define WM8915_FLL_CONTROL_6 0x225
-#define WM8915_FLL_EFS_1 0x226
-#define WM8915_FLL_EFS_2 0x227
-#define WM8915_AIF1_CONTROL 0x300
-#define WM8915_AIF1_BCLK 0x301
-#define WM8915_AIF1_TX_LRCLK_1 0x302
-#define WM8915_AIF1_TX_LRCLK_2 0x303
-#define WM8915_AIF1_RX_LRCLK_1 0x304
-#define WM8915_AIF1_RX_LRCLK_2 0x305
-#define WM8915_AIF1TX_DATA_CONFIGURATION_1 0x306
-#define WM8915_AIF1TX_DATA_CONFIGURATION_2 0x307
-#define WM8915_AIF1RX_DATA_CONFIGURATION 0x308
-#define WM8915_AIF1TX_CHANNEL_0_CONFIGURATION 0x309
-#define WM8915_AIF1TX_CHANNEL_1_CONFIGURATION 0x30A
-#define WM8915_AIF1TX_CHANNEL_2_CONFIGURATION 0x30B
-#define WM8915_AIF1TX_CHANNEL_3_CONFIGURATION 0x30C
-#define WM8915_AIF1TX_CHANNEL_4_CONFIGURATION 0x30D
-#define WM8915_AIF1TX_CHANNEL_5_CONFIGURATION 0x30E
-#define WM8915_AIF1RX_CHANNEL_0_CONFIGURATION 0x30F
-#define WM8915_AIF1RX_CHANNEL_1_CONFIGURATION 0x310
-#define WM8915_AIF1RX_CHANNEL_2_CONFIGURATION 0x311
-#define WM8915_AIF1RX_CHANNEL_3_CONFIGURATION 0x312
-#define WM8915_AIF1RX_CHANNEL_4_CONFIGURATION 0x313
-#define WM8915_AIF1RX_CHANNEL_5_CONFIGURATION 0x314
-#define WM8915_AIF1RX_MONO_CONFIGURATION 0x315
-#define WM8915_AIF1TX_TEST 0x31A
-#define WM8915_AIF2_CONTROL 0x320
-#define WM8915_AIF2_BCLK 0x321
-#define WM8915_AIF2_TX_LRCLK_1 0x322
-#define WM8915_AIF2_TX_LRCLK_2 0x323
-#define WM8915_AIF2_RX_LRCLK_1 0x324
-#define WM8915_AIF2_RX_LRCLK_2 0x325
-#define WM8915_AIF2TX_DATA_CONFIGURATION_1 0x326
-#define WM8915_AIF2TX_DATA_CONFIGURATION_2 0x327
-#define WM8915_AIF2RX_DATA_CONFIGURATION 0x328
-#define WM8915_AIF2TX_CHANNEL_0_CONFIGURATION 0x329
-#define WM8915_AIF2TX_CHANNEL_1_CONFIGURATION 0x32A
-#define WM8915_AIF2RX_CHANNEL_0_CONFIGURATION 0x32B
-#define WM8915_AIF2RX_CHANNEL_1_CONFIGURATION 0x32C
-#define WM8915_AIF2RX_MONO_CONFIGURATION 0x32D
-#define WM8915_AIF2TX_TEST 0x32F
-#define WM8915_DSP1_TX_LEFT_VOLUME 0x400
-#define WM8915_DSP1_TX_RIGHT_VOLUME 0x401
-#define WM8915_DSP1_RX_LEFT_VOLUME 0x402
-#define WM8915_DSP1_RX_RIGHT_VOLUME 0x403
-#define WM8915_DSP1_TX_FILTERS 0x410
-#define WM8915_DSP1_RX_FILTERS_1 0x420
-#define WM8915_DSP1_RX_FILTERS_2 0x421
-#define WM8915_DSP1_DRC_1 0x440
-#define WM8915_DSP1_DRC_2 0x441
-#define WM8915_DSP1_DRC_3 0x442
-#define WM8915_DSP1_DRC_4 0x443
-#define WM8915_DSP1_DRC_5 0x444
-#define WM8915_DSP1_RX_EQ_GAINS_1 0x480
-#define WM8915_DSP1_RX_EQ_GAINS_2 0x481
-#define WM8915_DSP1_RX_EQ_BAND_1_A 0x482
-#define WM8915_DSP1_RX_EQ_BAND_1_B 0x483
-#define WM8915_DSP1_RX_EQ_BAND_1_PG 0x484
-#define WM8915_DSP1_RX_EQ_BAND_2_A 0x485
-#define WM8915_DSP1_RX_EQ_BAND_2_B 0x486
-#define WM8915_DSP1_RX_EQ_BAND_2_C 0x487
-#define WM8915_DSP1_RX_EQ_BAND_2_PG 0x488
-#define WM8915_DSP1_RX_EQ_BAND_3_A 0x489
-#define WM8915_DSP1_RX_EQ_BAND_3_B 0x48A
-#define WM8915_DSP1_RX_EQ_BAND_3_C 0x48B
-#define WM8915_DSP1_RX_EQ_BAND_3_PG 0x48C
-#define WM8915_DSP1_RX_EQ_BAND_4_A 0x48D
-#define WM8915_DSP1_RX_EQ_BAND_4_B 0x48E
-#define WM8915_DSP1_RX_EQ_BAND_4_C 0x48F
-#define WM8915_DSP1_RX_EQ_BAND_4_PG 0x490
-#define WM8915_DSP1_RX_EQ_BAND_5_A 0x491
-#define WM8915_DSP1_RX_EQ_BAND_5_B 0x492
-#define WM8915_DSP1_RX_EQ_BAND_5_PG 0x493
-#define WM8915_DSP2_TX_LEFT_VOLUME 0x500
-#define WM8915_DSP2_TX_RIGHT_VOLUME 0x501
-#define WM8915_DSP2_RX_LEFT_VOLUME 0x502
-#define WM8915_DSP2_RX_RIGHT_VOLUME 0x503
-#define WM8915_DSP2_TX_FILTERS 0x510
-#define WM8915_DSP2_RX_FILTERS_1 0x520
-#define WM8915_DSP2_RX_FILTERS_2 0x521
-#define WM8915_DSP2_DRC_1 0x540
-#define WM8915_DSP2_DRC_2 0x541
-#define WM8915_DSP2_DRC_3 0x542
-#define WM8915_DSP2_DRC_4 0x543
-#define WM8915_DSP2_DRC_5 0x544
-#define WM8915_DSP2_RX_EQ_GAINS_1 0x580
-#define WM8915_DSP2_RX_EQ_GAINS_2 0x581
-#define WM8915_DSP2_RX_EQ_BAND_1_A 0x582
-#define WM8915_DSP2_RX_EQ_BAND_1_B 0x583
-#define WM8915_DSP2_RX_EQ_BAND_1_PG 0x584
-#define WM8915_DSP2_RX_EQ_BAND_2_A 0x585
-#define WM8915_DSP2_RX_EQ_BAND_2_B 0x586
-#define WM8915_DSP2_RX_EQ_BAND_2_C 0x587
-#define WM8915_DSP2_RX_EQ_BAND_2_PG 0x588
-#define WM8915_DSP2_RX_EQ_BAND_3_A 0x589
-#define WM8915_DSP2_RX_EQ_BAND_3_B 0x58A
-#define WM8915_DSP2_RX_EQ_BAND_3_C 0x58B
-#define WM8915_DSP2_RX_EQ_BAND_3_PG 0x58C
-#define WM8915_DSP2_RX_EQ_BAND_4_A 0x58D
-#define WM8915_DSP2_RX_EQ_BAND_4_B 0x58E
-#define WM8915_DSP2_RX_EQ_BAND_4_C 0x58F
-#define WM8915_DSP2_RX_EQ_BAND_4_PG 0x590
-#define WM8915_DSP2_RX_EQ_BAND_5_A 0x591
-#define WM8915_DSP2_RX_EQ_BAND_5_B 0x592
-#define WM8915_DSP2_RX_EQ_BAND_5_PG 0x593
-#define WM8915_DAC1_MIXER_VOLUMES 0x600
-#define WM8915_DAC1_LEFT_MIXER_ROUTING 0x601
-#define WM8915_DAC1_RIGHT_MIXER_ROUTING 0x602
-#define WM8915_DAC2_MIXER_VOLUMES 0x603
-#define WM8915_DAC2_LEFT_MIXER_ROUTING 0x604
-#define WM8915_DAC2_RIGHT_MIXER_ROUTING 0x605
-#define WM8915_DSP1_TX_LEFT_MIXER_ROUTING 0x606
-#define WM8915_DSP1_TX_RIGHT_MIXER_ROUTING 0x607
-#define WM8915_DSP2_TX_LEFT_MIXER_ROUTING 0x608
-#define WM8915_DSP2_TX_RIGHT_MIXER_ROUTING 0x609
-#define WM8915_DSP_TX_MIXER_SELECT 0x60A
-#define WM8915_DAC_SOFTMUTE 0x610
-#define WM8915_OVERSAMPLING 0x620
-#define WM8915_SIDETONE 0x621
-#define WM8915_GPIO_1 0x700
-#define WM8915_GPIO_2 0x701
-#define WM8915_GPIO_3 0x702
-#define WM8915_GPIO_4 0x703
-#define WM8915_GPIO_5 0x704
-#define WM8915_PULL_CONTROL_1 0x720
-#define WM8915_PULL_CONTROL_2 0x721
-#define WM8915_INTERRUPT_STATUS_1 0x730
-#define WM8915_INTERRUPT_STATUS_2 0x731
-#define WM8915_INTERRUPT_RAW_STATUS_2 0x732
-#define WM8915_INTERRUPT_STATUS_1_MASK 0x738
-#define WM8915_INTERRUPT_STATUS_2_MASK 0x739
-#define WM8915_INTERRUPT_CONTROL 0x740
-#define WM8915_LEFT_PDM_SPEAKER 0x800
-#define WM8915_RIGHT_PDM_SPEAKER 0x801
-#define WM8915_PDM_SPEAKER_MUTE_SEQUENCE 0x802
-#define WM8915_PDM_SPEAKER_VOLUME 0x803
-#define WM8915_WRITE_SEQUENCER_0 0x3000
-#define WM8915_WRITE_SEQUENCER_1 0x3001
-#define WM8915_WRITE_SEQUENCER_2 0x3002
-#define WM8915_WRITE_SEQUENCER_3 0x3003
-#define WM8915_WRITE_SEQUENCER_4 0x3004
-#define WM8915_WRITE_SEQUENCER_5 0x3005
-#define WM8915_WRITE_SEQUENCER_6 0x3006
-#define WM8915_WRITE_SEQUENCER_7 0x3007
-#define WM8915_WRITE_SEQUENCER_8 0x3008
-#define WM8915_WRITE_SEQUENCER_9 0x3009
-#define WM8915_WRITE_SEQUENCER_10 0x300A
-#define WM8915_WRITE_SEQUENCER_11 0x300B
-#define WM8915_WRITE_SEQUENCER_12 0x300C
-#define WM8915_WRITE_SEQUENCER_13 0x300D
-#define WM8915_WRITE_SEQUENCER_14 0x300E
-#define WM8915_WRITE_SEQUENCER_15 0x300F
-#define WM8915_WRITE_SEQUENCER_16 0x3010
-#define WM8915_WRITE_SEQUENCER_17 0x3011
-#define WM8915_WRITE_SEQUENCER_18 0x3012
-#define WM8915_WRITE_SEQUENCER_19 0x3013
-#define WM8915_WRITE_SEQUENCER_20 0x3014
-#define WM8915_WRITE_SEQUENCER_21 0x3015
-#define WM8915_WRITE_SEQUENCER_22 0x3016
-#define WM8915_WRITE_SEQUENCER_23 0x3017
-#define WM8915_WRITE_SEQUENCER_24 0x3018
-#define WM8915_WRITE_SEQUENCER_25 0x3019
-#define WM8915_WRITE_SEQUENCER_26 0x301A
-#define WM8915_WRITE_SEQUENCER_27 0x301B
-#define WM8915_WRITE_SEQUENCER_28 0x301C
-#define WM8915_WRITE_SEQUENCER_29 0x301D
-#define WM8915_WRITE_SEQUENCER_30 0x301E
-#define WM8915_WRITE_SEQUENCER_31 0x301F
-#define WM8915_WRITE_SEQUENCER_32 0x3020
-#define WM8915_WRITE_SEQUENCER_33 0x3021
-#define WM8915_WRITE_SEQUENCER_34 0x3022
-#define WM8915_WRITE_SEQUENCER_35 0x3023
-#define WM8915_WRITE_SEQUENCER_36 0x3024
-#define WM8915_WRITE_SEQUENCER_37 0x3025
-#define WM8915_WRITE_SEQUENCER_38 0x3026
-#define WM8915_WRITE_SEQUENCER_39 0x3027
-#define WM8915_WRITE_SEQUENCER_40 0x3028
-#define WM8915_WRITE_SEQUENCER_41 0x3029
-#define WM8915_WRITE_SEQUENCER_42 0x302A
-#define WM8915_WRITE_SEQUENCER_43 0x302B
-#define WM8915_WRITE_SEQUENCER_44 0x302C
-#define WM8915_WRITE_SEQUENCER_45 0x302D
-#define WM8915_WRITE_SEQUENCER_46 0x302E
-#define WM8915_WRITE_SEQUENCER_47 0x302F
-#define WM8915_WRITE_SEQUENCER_48 0x3030
-#define WM8915_WRITE_SEQUENCER_49 0x3031
-#define WM8915_WRITE_SEQUENCER_50 0x3032
-#define WM8915_WRITE_SEQUENCER_51 0x3033
-#define WM8915_WRITE_SEQUENCER_52 0x3034
-#define WM8915_WRITE_SEQUENCER_53 0x3035
-#define WM8915_WRITE_SEQUENCER_54 0x3036
-#define WM8915_WRITE_SEQUENCER_55 0x3037
-#define WM8915_WRITE_SEQUENCER_56 0x3038
-#define WM8915_WRITE_SEQUENCER_57 0x3039
-#define WM8915_WRITE_SEQUENCER_58 0x303A
-#define WM8915_WRITE_SEQUENCER_59 0x303B
-#define WM8915_WRITE_SEQUENCER_60 0x303C
-#define WM8915_WRITE_SEQUENCER_61 0x303D
-#define WM8915_WRITE_SEQUENCER_62 0x303E
-#define WM8915_WRITE_SEQUENCER_63 0x303F
-#define WM8915_WRITE_SEQUENCER_64 0x3040
-#define WM8915_WRITE_SEQUENCER_65 0x3041
-#define WM8915_WRITE_SEQUENCER_66 0x3042
-#define WM8915_WRITE_SEQUENCER_67 0x3043
-#define WM8915_WRITE_SEQUENCER_68 0x3044
-#define WM8915_WRITE_SEQUENCER_69 0x3045
-#define WM8915_WRITE_SEQUENCER_70 0x3046
-#define WM8915_WRITE_SEQUENCER_71 0x3047
-#define WM8915_WRITE_SEQUENCER_72 0x3048
-#define WM8915_WRITE_SEQUENCER_73 0x3049
-#define WM8915_WRITE_SEQUENCER_74 0x304A
-#define WM8915_WRITE_SEQUENCER_75 0x304B
-#define WM8915_WRITE_SEQUENCER_76 0x304C
-#define WM8915_WRITE_SEQUENCER_77 0x304D
-#define WM8915_WRITE_SEQUENCER_78 0x304E
-#define WM8915_WRITE_SEQUENCER_79 0x304F
-#define WM8915_WRITE_SEQUENCER_80 0x3050
-#define WM8915_WRITE_SEQUENCER_81 0x3051
-#define WM8915_WRITE_SEQUENCER_82 0x3052
-#define WM8915_WRITE_SEQUENCER_83 0x3053
-#define WM8915_WRITE_SEQUENCER_84 0x3054
-#define WM8915_WRITE_SEQUENCER_85 0x3055
-#define WM8915_WRITE_SEQUENCER_86 0x3056
-#define WM8915_WRITE_SEQUENCER_87 0x3057
-#define WM8915_WRITE_SEQUENCER_88 0x3058
-#define WM8915_WRITE_SEQUENCER_89 0x3059
-#define WM8915_WRITE_SEQUENCER_90 0x305A
-#define WM8915_WRITE_SEQUENCER_91 0x305B
-#define WM8915_WRITE_SEQUENCER_92 0x305C
-#define WM8915_WRITE_SEQUENCER_93 0x305D
-#define WM8915_WRITE_SEQUENCER_94 0x305E
-#define WM8915_WRITE_SEQUENCER_95 0x305F
-#define WM8915_WRITE_SEQUENCER_96 0x3060
-#define WM8915_WRITE_SEQUENCER_97 0x3061
-#define WM8915_WRITE_SEQUENCER_98 0x3062
-#define WM8915_WRITE_SEQUENCER_99 0x3063
-#define WM8915_WRITE_SEQUENCER_100 0x3064
-#define WM8915_WRITE_SEQUENCER_101 0x3065
-#define WM8915_WRITE_SEQUENCER_102 0x3066
-#define WM8915_WRITE_SEQUENCER_103 0x3067
-#define WM8915_WRITE_SEQUENCER_104 0x3068
-#define WM8915_WRITE_SEQUENCER_105 0x3069
-#define WM8915_WRITE_SEQUENCER_106 0x306A
-#define WM8915_WRITE_SEQUENCER_107 0x306B
-#define WM8915_WRITE_SEQUENCER_108 0x306C
-#define WM8915_WRITE_SEQUENCER_109 0x306D
-#define WM8915_WRITE_SEQUENCER_110 0x306E
-#define WM8915_WRITE_SEQUENCER_111 0x306F
-#define WM8915_WRITE_SEQUENCER_112 0x3070
-#define WM8915_WRITE_SEQUENCER_113 0x3071
-#define WM8915_WRITE_SEQUENCER_114 0x3072
-#define WM8915_WRITE_SEQUENCER_115 0x3073
-#define WM8915_WRITE_SEQUENCER_116 0x3074
-#define WM8915_WRITE_SEQUENCER_117 0x3075
-#define WM8915_WRITE_SEQUENCER_118 0x3076
-#define WM8915_WRITE_SEQUENCER_119 0x3077
-#define WM8915_WRITE_SEQUENCER_120 0x3078
-#define WM8915_WRITE_SEQUENCER_121 0x3079
-#define WM8915_WRITE_SEQUENCER_122 0x307A
-#define WM8915_WRITE_SEQUENCER_123 0x307B
-#define WM8915_WRITE_SEQUENCER_124 0x307C
-#define WM8915_WRITE_SEQUENCER_125 0x307D
-#define WM8915_WRITE_SEQUENCER_126 0x307E
-#define WM8915_WRITE_SEQUENCER_127 0x307F
-#define WM8915_WRITE_SEQUENCER_128 0x3080
-#define WM8915_WRITE_SEQUENCER_129 0x3081
-#define WM8915_WRITE_SEQUENCER_130 0x3082
-#define WM8915_WRITE_SEQUENCER_131 0x3083
-#define WM8915_WRITE_SEQUENCER_132 0x3084
-#define WM8915_WRITE_SEQUENCER_133 0x3085
-#define WM8915_WRITE_SEQUENCER_134 0x3086
-#define WM8915_WRITE_SEQUENCER_135 0x3087
-#define WM8915_WRITE_SEQUENCER_136 0x3088
-#define WM8915_WRITE_SEQUENCER_137 0x3089
-#define WM8915_WRITE_SEQUENCER_138 0x308A
-#define WM8915_WRITE_SEQUENCER_139 0x308B
-#define WM8915_WRITE_SEQUENCER_140 0x308C
-#define WM8915_WRITE_SEQUENCER_141 0x308D
-#define WM8915_WRITE_SEQUENCER_142 0x308E
-#define WM8915_WRITE_SEQUENCER_143 0x308F
-#define WM8915_WRITE_SEQUENCER_144 0x3090
-#define WM8915_WRITE_SEQUENCER_145 0x3091
-#define WM8915_WRITE_SEQUENCER_146 0x3092
-#define WM8915_WRITE_SEQUENCER_147 0x3093
-#define WM8915_WRITE_SEQUENCER_148 0x3094
-#define WM8915_WRITE_SEQUENCER_149 0x3095
-#define WM8915_WRITE_SEQUENCER_150 0x3096
-#define WM8915_WRITE_SEQUENCER_151 0x3097
-#define WM8915_WRITE_SEQUENCER_152 0x3098
-#define WM8915_WRITE_SEQUENCER_153 0x3099
-#define WM8915_WRITE_SEQUENCER_154 0x309A
-#define WM8915_WRITE_SEQUENCER_155 0x309B
-#define WM8915_WRITE_SEQUENCER_156 0x309C
-#define WM8915_WRITE_SEQUENCER_157 0x309D
-#define WM8915_WRITE_SEQUENCER_158 0x309E
-#define WM8915_WRITE_SEQUENCER_159 0x309F
-#define WM8915_WRITE_SEQUENCER_160 0x30A0
-#define WM8915_WRITE_SEQUENCER_161 0x30A1
-#define WM8915_WRITE_SEQUENCER_162 0x30A2
-#define WM8915_WRITE_SEQUENCER_163 0x30A3
-#define WM8915_WRITE_SEQUENCER_164 0x30A4
-#define WM8915_WRITE_SEQUENCER_165 0x30A5
-#define WM8915_WRITE_SEQUENCER_166 0x30A6
-#define WM8915_WRITE_SEQUENCER_167 0x30A7
-#define WM8915_WRITE_SEQUENCER_168 0x30A8
-#define WM8915_WRITE_SEQUENCER_169 0x30A9
-#define WM8915_WRITE_SEQUENCER_170 0x30AA
-#define WM8915_WRITE_SEQUENCER_171 0x30AB
-#define WM8915_WRITE_SEQUENCER_172 0x30AC
-#define WM8915_WRITE_SEQUENCER_173 0x30AD
-#define WM8915_WRITE_SEQUENCER_174 0x30AE
-#define WM8915_WRITE_SEQUENCER_175 0x30AF
-#define WM8915_WRITE_SEQUENCER_176 0x30B0
-#define WM8915_WRITE_SEQUENCER_177 0x30B1
-#define WM8915_WRITE_SEQUENCER_178 0x30B2
-#define WM8915_WRITE_SEQUENCER_179 0x30B3
-#define WM8915_WRITE_SEQUENCER_180 0x30B4
-#define WM8915_WRITE_SEQUENCER_181 0x30B5
-#define WM8915_WRITE_SEQUENCER_182 0x30B6
-#define WM8915_WRITE_SEQUENCER_183 0x30B7
-#define WM8915_WRITE_SEQUENCER_184 0x30B8
-#define WM8915_WRITE_SEQUENCER_185 0x30B9
-#define WM8915_WRITE_SEQUENCER_186 0x30BA
-#define WM8915_WRITE_SEQUENCER_187 0x30BB
-#define WM8915_WRITE_SEQUENCER_188 0x30BC
-#define WM8915_WRITE_SEQUENCER_189 0x30BD
-#define WM8915_WRITE_SEQUENCER_190 0x30BE
-#define WM8915_WRITE_SEQUENCER_191 0x30BF
-#define WM8915_WRITE_SEQUENCER_192 0x30C0
-#define WM8915_WRITE_SEQUENCER_193 0x30C1
-#define WM8915_WRITE_SEQUENCER_194 0x30C2
-#define WM8915_WRITE_SEQUENCER_195 0x30C3
-#define WM8915_WRITE_SEQUENCER_196 0x30C4
-#define WM8915_WRITE_SEQUENCER_197 0x30C5
-#define WM8915_WRITE_SEQUENCER_198 0x30C6
-#define WM8915_WRITE_SEQUENCER_199 0x30C7
-#define WM8915_WRITE_SEQUENCER_200 0x30C8
-#define WM8915_WRITE_SEQUENCER_201 0x30C9
-#define WM8915_WRITE_SEQUENCER_202 0x30CA
-#define WM8915_WRITE_SEQUENCER_203 0x30CB
-#define WM8915_WRITE_SEQUENCER_204 0x30CC
-#define WM8915_WRITE_SEQUENCER_205 0x30CD
-#define WM8915_WRITE_SEQUENCER_206 0x30CE
-#define WM8915_WRITE_SEQUENCER_207 0x30CF
-#define WM8915_WRITE_SEQUENCER_208 0x30D0
-#define WM8915_WRITE_SEQUENCER_209 0x30D1
-#define WM8915_WRITE_SEQUENCER_210 0x30D2
-#define WM8915_WRITE_SEQUENCER_211 0x30D3
-#define WM8915_WRITE_SEQUENCER_212 0x30D4
-#define WM8915_WRITE_SEQUENCER_213 0x30D5
-#define WM8915_WRITE_SEQUENCER_214 0x30D6
-#define WM8915_WRITE_SEQUENCER_215 0x30D7
-#define WM8915_WRITE_SEQUENCER_216 0x30D8
-#define WM8915_WRITE_SEQUENCER_217 0x30D9
-#define WM8915_WRITE_SEQUENCER_218 0x30DA
-#define WM8915_WRITE_SEQUENCER_219 0x30DB
-#define WM8915_WRITE_SEQUENCER_220 0x30DC
-#define WM8915_WRITE_SEQUENCER_221 0x30DD
-#define WM8915_WRITE_SEQUENCER_222 0x30DE
-#define WM8915_WRITE_SEQUENCER_223 0x30DF
-#define WM8915_WRITE_SEQUENCER_224 0x30E0
-#define WM8915_WRITE_SEQUENCER_225 0x30E1
-#define WM8915_WRITE_SEQUENCER_226 0x30E2
-#define WM8915_WRITE_SEQUENCER_227 0x30E3
-#define WM8915_WRITE_SEQUENCER_228 0x30E4
-#define WM8915_WRITE_SEQUENCER_229 0x30E5
-#define WM8915_WRITE_SEQUENCER_230 0x30E6
-#define WM8915_WRITE_SEQUENCER_231 0x30E7
-#define WM8915_WRITE_SEQUENCER_232 0x30E8
-#define WM8915_WRITE_SEQUENCER_233 0x30E9
-#define WM8915_WRITE_SEQUENCER_234 0x30EA
-#define WM8915_WRITE_SEQUENCER_235 0x30EB
-#define WM8915_WRITE_SEQUENCER_236 0x30EC
-#define WM8915_WRITE_SEQUENCER_237 0x30ED
-#define WM8915_WRITE_SEQUENCER_238 0x30EE
-#define WM8915_WRITE_SEQUENCER_239 0x30EF
-#define WM8915_WRITE_SEQUENCER_240 0x30F0
-#define WM8915_WRITE_SEQUENCER_241 0x30F1
-#define WM8915_WRITE_SEQUENCER_242 0x30F2
-#define WM8915_WRITE_SEQUENCER_243 0x30F3
-#define WM8915_WRITE_SEQUENCER_244 0x30F4
-#define WM8915_WRITE_SEQUENCER_245 0x30F5
-#define WM8915_WRITE_SEQUENCER_246 0x30F6
-#define WM8915_WRITE_SEQUENCER_247 0x30F7
-#define WM8915_WRITE_SEQUENCER_248 0x30F8
-#define WM8915_WRITE_SEQUENCER_249 0x30F9
-#define WM8915_WRITE_SEQUENCER_250 0x30FA
-#define WM8915_WRITE_SEQUENCER_251 0x30FB
-#define WM8915_WRITE_SEQUENCER_252 0x30FC
-#define WM8915_WRITE_SEQUENCER_253 0x30FD
-#define WM8915_WRITE_SEQUENCER_254 0x30FE
-#define WM8915_WRITE_SEQUENCER_255 0x30FF
-#define WM8915_WRITE_SEQUENCER_256 0x3100
-#define WM8915_WRITE_SEQUENCER_257 0x3101
-#define WM8915_WRITE_SEQUENCER_258 0x3102
-#define WM8915_WRITE_SEQUENCER_259 0x3103
-#define WM8915_WRITE_SEQUENCER_260 0x3104
-#define WM8915_WRITE_SEQUENCER_261 0x3105
-#define WM8915_WRITE_SEQUENCER_262 0x3106
-#define WM8915_WRITE_SEQUENCER_263 0x3107
-#define WM8915_WRITE_SEQUENCER_264 0x3108
-#define WM8915_WRITE_SEQUENCER_265 0x3109
-#define WM8915_WRITE_SEQUENCER_266 0x310A
-#define WM8915_WRITE_SEQUENCER_267 0x310B
-#define WM8915_WRITE_SEQUENCER_268 0x310C
-#define WM8915_WRITE_SEQUENCER_269 0x310D
-#define WM8915_WRITE_SEQUENCER_270 0x310E
-#define WM8915_WRITE_SEQUENCER_271 0x310F
-#define WM8915_WRITE_SEQUENCER_272 0x3110
-#define WM8915_WRITE_SEQUENCER_273 0x3111
-#define WM8915_WRITE_SEQUENCER_274 0x3112
-#define WM8915_WRITE_SEQUENCER_275 0x3113
-#define WM8915_WRITE_SEQUENCER_276 0x3114
-#define WM8915_WRITE_SEQUENCER_277 0x3115
-#define WM8915_WRITE_SEQUENCER_278 0x3116
-#define WM8915_WRITE_SEQUENCER_279 0x3117
-#define WM8915_WRITE_SEQUENCER_280 0x3118
-#define WM8915_WRITE_SEQUENCER_281 0x3119
-#define WM8915_WRITE_SEQUENCER_282 0x311A
-#define WM8915_WRITE_SEQUENCER_283 0x311B
-#define WM8915_WRITE_SEQUENCER_284 0x311C
-#define WM8915_WRITE_SEQUENCER_285 0x311D
-#define WM8915_WRITE_SEQUENCER_286 0x311E
-#define WM8915_WRITE_SEQUENCER_287 0x311F
-#define WM8915_WRITE_SEQUENCER_288 0x3120
-#define WM8915_WRITE_SEQUENCER_289 0x3121
-#define WM8915_WRITE_SEQUENCER_290 0x3122
-#define WM8915_WRITE_SEQUENCER_291 0x3123
-#define WM8915_WRITE_SEQUENCER_292 0x3124
-#define WM8915_WRITE_SEQUENCER_293 0x3125
-#define WM8915_WRITE_SEQUENCER_294 0x3126
-#define WM8915_WRITE_SEQUENCER_295 0x3127
-#define WM8915_WRITE_SEQUENCER_296 0x3128
-#define WM8915_WRITE_SEQUENCER_297 0x3129
-#define WM8915_WRITE_SEQUENCER_298 0x312A
-#define WM8915_WRITE_SEQUENCER_299 0x312B
-#define WM8915_WRITE_SEQUENCER_300 0x312C
-#define WM8915_WRITE_SEQUENCER_301 0x312D
-#define WM8915_WRITE_SEQUENCER_302 0x312E
-#define WM8915_WRITE_SEQUENCER_303 0x312F
-#define WM8915_WRITE_SEQUENCER_304 0x3130
-#define WM8915_WRITE_SEQUENCER_305 0x3131
-#define WM8915_WRITE_SEQUENCER_306 0x3132
-#define WM8915_WRITE_SEQUENCER_307 0x3133
-#define WM8915_WRITE_SEQUENCER_308 0x3134
-#define WM8915_WRITE_SEQUENCER_309 0x3135
-#define WM8915_WRITE_SEQUENCER_310 0x3136
-#define WM8915_WRITE_SEQUENCER_311 0x3137
-#define WM8915_WRITE_SEQUENCER_312 0x3138
-#define WM8915_WRITE_SEQUENCER_313 0x3139
-#define WM8915_WRITE_SEQUENCER_314 0x313A
-#define WM8915_WRITE_SEQUENCER_315 0x313B
-#define WM8915_WRITE_SEQUENCER_316 0x313C
-#define WM8915_WRITE_SEQUENCER_317 0x313D
-#define WM8915_WRITE_SEQUENCER_318 0x313E
-#define WM8915_WRITE_SEQUENCER_319 0x313F
-#define WM8915_WRITE_SEQUENCER_320 0x3140
-#define WM8915_WRITE_SEQUENCER_321 0x3141
-#define WM8915_WRITE_SEQUENCER_322 0x3142
-#define WM8915_WRITE_SEQUENCER_323 0x3143
-#define WM8915_WRITE_SEQUENCER_324 0x3144
-#define WM8915_WRITE_SEQUENCER_325 0x3145
-#define WM8915_WRITE_SEQUENCER_326 0x3146
-#define WM8915_WRITE_SEQUENCER_327 0x3147
-#define WM8915_WRITE_SEQUENCER_328 0x3148
-#define WM8915_WRITE_SEQUENCER_329 0x3149
-#define WM8915_WRITE_SEQUENCER_330 0x314A
-#define WM8915_WRITE_SEQUENCER_331 0x314B
-#define WM8915_WRITE_SEQUENCER_332 0x314C
-#define WM8915_WRITE_SEQUENCER_333 0x314D
-#define WM8915_WRITE_SEQUENCER_334 0x314E
-#define WM8915_WRITE_SEQUENCER_335 0x314F
-#define WM8915_WRITE_SEQUENCER_336 0x3150
-#define WM8915_WRITE_SEQUENCER_337 0x3151
-#define WM8915_WRITE_SEQUENCER_338 0x3152
-#define WM8915_WRITE_SEQUENCER_339 0x3153
-#define WM8915_WRITE_SEQUENCER_340 0x3154
-#define WM8915_WRITE_SEQUENCER_341 0x3155
-#define WM8915_WRITE_SEQUENCER_342 0x3156
-#define WM8915_WRITE_SEQUENCER_343 0x3157
-#define WM8915_WRITE_SEQUENCER_344 0x3158
-#define WM8915_WRITE_SEQUENCER_345 0x3159
-#define WM8915_WRITE_SEQUENCER_346 0x315A
-#define WM8915_WRITE_SEQUENCER_347 0x315B
-#define WM8915_WRITE_SEQUENCER_348 0x315C
-#define WM8915_WRITE_SEQUENCER_349 0x315D
-#define WM8915_WRITE_SEQUENCER_350 0x315E
-#define WM8915_WRITE_SEQUENCER_351 0x315F
-#define WM8915_WRITE_SEQUENCER_352 0x3160
-#define WM8915_WRITE_SEQUENCER_353 0x3161
-#define WM8915_WRITE_SEQUENCER_354 0x3162
-#define WM8915_WRITE_SEQUENCER_355 0x3163
-#define WM8915_WRITE_SEQUENCER_356 0x3164
-#define WM8915_WRITE_SEQUENCER_357 0x3165
-#define WM8915_WRITE_SEQUENCER_358 0x3166
-#define WM8915_WRITE_SEQUENCER_359 0x3167
-#define WM8915_WRITE_SEQUENCER_360 0x3168
-#define WM8915_WRITE_SEQUENCER_361 0x3169
-#define WM8915_WRITE_SEQUENCER_362 0x316A
-#define WM8915_WRITE_SEQUENCER_363 0x316B
-#define WM8915_WRITE_SEQUENCER_364 0x316C
-#define WM8915_WRITE_SEQUENCER_365 0x316D
-#define WM8915_WRITE_SEQUENCER_366 0x316E
-#define WM8915_WRITE_SEQUENCER_367 0x316F
-#define WM8915_WRITE_SEQUENCER_368 0x3170
-#define WM8915_WRITE_SEQUENCER_369 0x3171
-#define WM8915_WRITE_SEQUENCER_370 0x3172
-#define WM8915_WRITE_SEQUENCER_371 0x3173
-#define WM8915_WRITE_SEQUENCER_372 0x3174
-#define WM8915_WRITE_SEQUENCER_373 0x3175
-#define WM8915_WRITE_SEQUENCER_374 0x3176
-#define WM8915_WRITE_SEQUENCER_375 0x3177
-#define WM8915_WRITE_SEQUENCER_376 0x3178
-#define WM8915_WRITE_SEQUENCER_377 0x3179
-#define WM8915_WRITE_SEQUENCER_378 0x317A
-#define WM8915_WRITE_SEQUENCER_379 0x317B
-#define WM8915_WRITE_SEQUENCER_380 0x317C
-#define WM8915_WRITE_SEQUENCER_381 0x317D
-#define WM8915_WRITE_SEQUENCER_382 0x317E
-#define WM8915_WRITE_SEQUENCER_383 0x317F
-#define WM8915_WRITE_SEQUENCER_384 0x3180
-#define WM8915_WRITE_SEQUENCER_385 0x3181
-#define WM8915_WRITE_SEQUENCER_386 0x3182
-#define WM8915_WRITE_SEQUENCER_387 0x3183
-#define WM8915_WRITE_SEQUENCER_388 0x3184
-#define WM8915_WRITE_SEQUENCER_389 0x3185
-#define WM8915_WRITE_SEQUENCER_390 0x3186
-#define WM8915_WRITE_SEQUENCER_391 0x3187
-#define WM8915_WRITE_SEQUENCER_392 0x3188
-#define WM8915_WRITE_SEQUENCER_393 0x3189
-#define WM8915_WRITE_SEQUENCER_394 0x318A
-#define WM8915_WRITE_SEQUENCER_395 0x318B
-#define WM8915_WRITE_SEQUENCER_396 0x318C
-#define WM8915_WRITE_SEQUENCER_397 0x318D
-#define WM8915_WRITE_SEQUENCER_398 0x318E
-#define WM8915_WRITE_SEQUENCER_399 0x318F
-#define WM8915_WRITE_SEQUENCER_400 0x3190
-#define WM8915_WRITE_SEQUENCER_401 0x3191
-#define WM8915_WRITE_SEQUENCER_402 0x3192
-#define WM8915_WRITE_SEQUENCER_403 0x3193
-#define WM8915_WRITE_SEQUENCER_404 0x3194
-#define WM8915_WRITE_SEQUENCER_405 0x3195
-#define WM8915_WRITE_SEQUENCER_406 0x3196
-#define WM8915_WRITE_SEQUENCER_407 0x3197
-#define WM8915_WRITE_SEQUENCER_408 0x3198
-#define WM8915_WRITE_SEQUENCER_409 0x3199
-#define WM8915_WRITE_SEQUENCER_410 0x319A
-#define WM8915_WRITE_SEQUENCER_411 0x319B
-#define WM8915_WRITE_SEQUENCER_412 0x319C
-#define WM8915_WRITE_SEQUENCER_413 0x319D
-#define WM8915_WRITE_SEQUENCER_414 0x319E
-#define WM8915_WRITE_SEQUENCER_415 0x319F
-#define WM8915_WRITE_SEQUENCER_416 0x31A0
-#define WM8915_WRITE_SEQUENCER_417 0x31A1
-#define WM8915_WRITE_SEQUENCER_418 0x31A2
-#define WM8915_WRITE_SEQUENCER_419 0x31A3
-#define WM8915_WRITE_SEQUENCER_420 0x31A4
-#define WM8915_WRITE_SEQUENCER_421 0x31A5
-#define WM8915_WRITE_SEQUENCER_422 0x31A6
-#define WM8915_WRITE_SEQUENCER_423 0x31A7
-#define WM8915_WRITE_SEQUENCER_424 0x31A8
-#define WM8915_WRITE_SEQUENCER_425 0x31A9
-#define WM8915_WRITE_SEQUENCER_426 0x31AA
-#define WM8915_WRITE_SEQUENCER_427 0x31AB
-#define WM8915_WRITE_SEQUENCER_428 0x31AC
-#define WM8915_WRITE_SEQUENCER_429 0x31AD
-#define WM8915_WRITE_SEQUENCER_430 0x31AE
-#define WM8915_WRITE_SEQUENCER_431 0x31AF
-#define WM8915_WRITE_SEQUENCER_432 0x31B0
-#define WM8915_WRITE_SEQUENCER_433 0x31B1
-#define WM8915_WRITE_SEQUENCER_434 0x31B2
-#define WM8915_WRITE_SEQUENCER_435 0x31B3
-#define WM8915_WRITE_SEQUENCER_436 0x31B4
-#define WM8915_WRITE_SEQUENCER_437 0x31B5
-#define WM8915_WRITE_SEQUENCER_438 0x31B6
-#define WM8915_WRITE_SEQUENCER_439 0x31B7
-#define WM8915_WRITE_SEQUENCER_440 0x31B8
-#define WM8915_WRITE_SEQUENCER_441 0x31B9
-#define WM8915_WRITE_SEQUENCER_442 0x31BA
-#define WM8915_WRITE_SEQUENCER_443 0x31BB
-#define WM8915_WRITE_SEQUENCER_444 0x31BC
-#define WM8915_WRITE_SEQUENCER_445 0x31BD
-#define WM8915_WRITE_SEQUENCER_446 0x31BE
-#define WM8915_WRITE_SEQUENCER_447 0x31BF
-#define WM8915_WRITE_SEQUENCER_448 0x31C0
-#define WM8915_WRITE_SEQUENCER_449 0x31C1
-#define WM8915_WRITE_SEQUENCER_450 0x31C2
-#define WM8915_WRITE_SEQUENCER_451 0x31C3
-#define WM8915_WRITE_SEQUENCER_452 0x31C4
-#define WM8915_WRITE_SEQUENCER_453 0x31C5
-#define WM8915_WRITE_SEQUENCER_454 0x31C6
-#define WM8915_WRITE_SEQUENCER_455 0x31C7
-#define WM8915_WRITE_SEQUENCER_456 0x31C8
-#define WM8915_WRITE_SEQUENCER_457 0x31C9
-#define WM8915_WRITE_SEQUENCER_458 0x31CA
-#define WM8915_WRITE_SEQUENCER_459 0x31CB
-#define WM8915_WRITE_SEQUENCER_460 0x31CC
-#define WM8915_WRITE_SEQUENCER_461 0x31CD
-#define WM8915_WRITE_SEQUENCER_462 0x31CE
-#define WM8915_WRITE_SEQUENCER_463 0x31CF
-#define WM8915_WRITE_SEQUENCER_464 0x31D0
-#define WM8915_WRITE_SEQUENCER_465 0x31D1
-#define WM8915_WRITE_SEQUENCER_466 0x31D2
-#define WM8915_WRITE_SEQUENCER_467 0x31D3
-#define WM8915_WRITE_SEQUENCER_468 0x31D4
-#define WM8915_WRITE_SEQUENCER_469 0x31D5
-#define WM8915_WRITE_SEQUENCER_470 0x31D6
-#define WM8915_WRITE_SEQUENCER_471 0x31D7
-#define WM8915_WRITE_SEQUENCER_472 0x31D8
-#define WM8915_WRITE_SEQUENCER_473 0x31D9
-#define WM8915_WRITE_SEQUENCER_474 0x31DA
-#define WM8915_WRITE_SEQUENCER_475 0x31DB
-#define WM8915_WRITE_SEQUENCER_476 0x31DC
-#define WM8915_WRITE_SEQUENCER_477 0x31DD
-#define WM8915_WRITE_SEQUENCER_478 0x31DE
-#define WM8915_WRITE_SEQUENCER_479 0x31DF
-#define WM8915_WRITE_SEQUENCER_480 0x31E0
-#define WM8915_WRITE_SEQUENCER_481 0x31E1
-#define WM8915_WRITE_SEQUENCER_482 0x31E2
-#define WM8915_WRITE_SEQUENCER_483 0x31E3
-#define WM8915_WRITE_SEQUENCER_484 0x31E4
-#define WM8915_WRITE_SEQUENCER_485 0x31E5
-#define WM8915_WRITE_SEQUENCER_486 0x31E6
-#define WM8915_WRITE_SEQUENCER_487 0x31E7
-#define WM8915_WRITE_SEQUENCER_488 0x31E8
-#define WM8915_WRITE_SEQUENCER_489 0x31E9
-#define WM8915_WRITE_SEQUENCER_490 0x31EA
-#define WM8915_WRITE_SEQUENCER_491 0x31EB
-#define WM8915_WRITE_SEQUENCER_492 0x31EC
-#define WM8915_WRITE_SEQUENCER_493 0x31ED
-#define WM8915_WRITE_SEQUENCER_494 0x31EE
-#define WM8915_WRITE_SEQUENCER_495 0x31EF
-#define WM8915_WRITE_SEQUENCER_496 0x31F0
-#define WM8915_WRITE_SEQUENCER_497 0x31F1
-#define WM8915_WRITE_SEQUENCER_498 0x31F2
-#define WM8915_WRITE_SEQUENCER_499 0x31F3
-#define WM8915_WRITE_SEQUENCER_500 0x31F4
-#define WM8915_WRITE_SEQUENCER_501 0x31F5
-#define WM8915_WRITE_SEQUENCER_502 0x31F6
-#define WM8915_WRITE_SEQUENCER_503 0x31F7
-#define WM8915_WRITE_SEQUENCER_504 0x31F8
-#define WM8915_WRITE_SEQUENCER_505 0x31F9
-#define WM8915_WRITE_SEQUENCER_506 0x31FA
-#define WM8915_WRITE_SEQUENCER_507 0x31FB
-#define WM8915_WRITE_SEQUENCER_508 0x31FC
-#define WM8915_WRITE_SEQUENCER_509 0x31FD
-#define WM8915_WRITE_SEQUENCER_510 0x31FE
-#define WM8915_WRITE_SEQUENCER_511 0x31FF
-
-#define WM8915_REGISTER_COUNT 706
-#define WM8915_MAX_REGISTER 0x31FF
-
-/*
- * Field Definitions.
- */
-
-/*
- * R0 (0x00) - Software Reset
- */
-#define WM8915_SW_RESET_MASK 0xFFFF /* SW_RESET - [15:0] */
-#define WM8915_SW_RESET_SHIFT 0 /* SW_RESET - [15:0] */
-#define WM8915_SW_RESET_WIDTH 16 /* SW_RESET - [15:0] */
-
-/*
- * R1 (0x01) - Power Management (1)
- */
-#define WM8915_MICB2_ENA 0x0200 /* MICB2_ENA */
-#define WM8915_MICB2_ENA_MASK 0x0200 /* MICB2_ENA */
-#define WM8915_MICB2_ENA_SHIFT 9 /* MICB2_ENA */
-#define WM8915_MICB2_ENA_WIDTH 1 /* MICB2_ENA */
-#define WM8915_MICB1_ENA 0x0100 /* MICB1_ENA */
-#define WM8915_MICB1_ENA_MASK 0x0100 /* MICB1_ENA */
-#define WM8915_MICB1_ENA_SHIFT 8 /* MICB1_ENA */
-#define WM8915_MICB1_ENA_WIDTH 1 /* MICB1_ENA */
-#define WM8915_HPOUT2L_ENA 0x0080 /* HPOUT2L_ENA */
-#define WM8915_HPOUT2L_ENA_MASK 0x0080 /* HPOUT2L_ENA */
-#define WM8915_HPOUT2L_ENA_SHIFT 7 /* HPOUT2L_ENA */
-#define WM8915_HPOUT2L_ENA_WIDTH 1 /* HPOUT2L_ENA */
-#define WM8915_HPOUT2R_ENA 0x0040 /* HPOUT2R_ENA */
-#define WM8915_HPOUT2R_ENA_MASK 0x0040 /* HPOUT2R_ENA */
-#define WM8915_HPOUT2R_ENA_SHIFT 6 /* HPOUT2R_ENA */
-#define WM8915_HPOUT2R_ENA_WIDTH 1 /* HPOUT2R_ENA */
-#define WM8915_HPOUT1L_ENA 0x0020 /* HPOUT1L_ENA */
-#define WM8915_HPOUT1L_ENA_MASK 0x0020 /* HPOUT1L_ENA */
-#define WM8915_HPOUT1L_ENA_SHIFT 5 /* HPOUT1L_ENA */
-#define WM8915_HPOUT1L_ENA_WIDTH 1 /* HPOUT1L_ENA */
-#define WM8915_HPOUT1R_ENA 0x0010 /* HPOUT1R_ENA */
-#define WM8915_HPOUT1R_ENA_MASK 0x0010 /* HPOUT1R_ENA */
-#define WM8915_HPOUT1R_ENA_SHIFT 4 /* HPOUT1R_ENA */
-#define WM8915_HPOUT1R_ENA_WIDTH 1 /* HPOUT1R_ENA */
-#define WM8915_BG_ENA 0x0001 /* BG_ENA */
-#define WM8915_BG_ENA_MASK 0x0001 /* BG_ENA */
-#define WM8915_BG_ENA_SHIFT 0 /* BG_ENA */
-#define WM8915_BG_ENA_WIDTH 1 /* BG_ENA */
-
-/*
- * R2 (0x02) - Power Management (2)
- */
-#define WM8915_OPCLK_ENA 0x0800 /* OPCLK_ENA */
-#define WM8915_OPCLK_ENA_MASK 0x0800 /* OPCLK_ENA */
-#define WM8915_OPCLK_ENA_SHIFT 11 /* OPCLK_ENA */
-#define WM8915_OPCLK_ENA_WIDTH 1 /* OPCLK_ENA */
-#define WM8915_INL_ENA 0x0020 /* INL_ENA */
-#define WM8915_INL_ENA_MASK 0x0020 /* INL_ENA */
-#define WM8915_INL_ENA_SHIFT 5 /* INL_ENA */
-#define WM8915_INL_ENA_WIDTH 1 /* INL_ENA */
-#define WM8915_INR_ENA 0x0010 /* INR_ENA */
-#define WM8915_INR_ENA_MASK 0x0010 /* INR_ENA */
-#define WM8915_INR_ENA_SHIFT 4 /* INR_ENA */
-#define WM8915_INR_ENA_WIDTH 1 /* INR_ENA */
-#define WM8915_LDO2_ENA 0x0002 /* LDO2_ENA */
-#define WM8915_LDO2_ENA_MASK 0x0002 /* LDO2_ENA */
-#define WM8915_LDO2_ENA_SHIFT 1 /* LDO2_ENA */
-#define WM8915_LDO2_ENA_WIDTH 1 /* LDO2_ENA */
-
-/*
- * R3 (0x03) - Power Management (3)
- */
-#define WM8915_DSP2RXL_ENA 0x0800 /* DSP2RXL_ENA */
-#define WM8915_DSP2RXL_ENA_MASK 0x0800 /* DSP2RXL_ENA */
-#define WM8915_DSP2RXL_ENA_SHIFT 11 /* DSP2RXL_ENA */
-#define WM8915_DSP2RXL_ENA_WIDTH 1 /* DSP2RXL_ENA */
-#define WM8915_DSP2RXR_ENA 0x0400 /* DSP2RXR_ENA */
-#define WM8915_DSP2RXR_ENA_MASK 0x0400 /* DSP2RXR_ENA */
-#define WM8915_DSP2RXR_ENA_SHIFT 10 /* DSP2RXR_ENA */
-#define WM8915_DSP2RXR_ENA_WIDTH 1 /* DSP2RXR_ENA */
-#define WM8915_DSP1RXL_ENA 0x0200 /* DSP1RXL_ENA */
-#define WM8915_DSP1RXL_ENA_MASK 0x0200 /* DSP1RXL_ENA */
-#define WM8915_DSP1RXL_ENA_SHIFT 9 /* DSP1RXL_ENA */
-#define WM8915_DSP1RXL_ENA_WIDTH 1 /* DSP1RXL_ENA */
-#define WM8915_DSP1RXR_ENA 0x0100 /* DSP1RXR_ENA */
-#define WM8915_DSP1RXR_ENA_MASK 0x0100 /* DSP1RXR_ENA */
-#define WM8915_DSP1RXR_ENA_SHIFT 8 /* DSP1RXR_ENA */
-#define WM8915_DSP1RXR_ENA_WIDTH 1 /* DSP1RXR_ENA */
-#define WM8915_DMIC2L_ENA 0x0020 /* DMIC2L_ENA */
-#define WM8915_DMIC2L_ENA_MASK 0x0020 /* DMIC2L_ENA */
-#define WM8915_DMIC2L_ENA_SHIFT 5 /* DMIC2L_ENA */
-#define WM8915_DMIC2L_ENA_WIDTH 1 /* DMIC2L_ENA */
-#define WM8915_DMIC2R_ENA 0x0010 /* DMIC2R_ENA */
-#define WM8915_DMIC2R_ENA_MASK 0x0010 /* DMIC2R_ENA */
-#define WM8915_DMIC2R_ENA_SHIFT 4 /* DMIC2R_ENA */
-#define WM8915_DMIC2R_ENA_WIDTH 1 /* DMIC2R_ENA */
-#define WM8915_DMIC1L_ENA 0x0008 /* DMIC1L_ENA */
-#define WM8915_DMIC1L_ENA_MASK 0x0008 /* DMIC1L_ENA */
-#define WM8915_DMIC1L_ENA_SHIFT 3 /* DMIC1L_ENA */
-#define WM8915_DMIC1L_ENA_WIDTH 1 /* DMIC1L_ENA */
-#define WM8915_DMIC1R_ENA 0x0004 /* DMIC1R_ENA */
-#define WM8915_DMIC1R_ENA_MASK 0x0004 /* DMIC1R_ENA */
-#define WM8915_DMIC1R_ENA_SHIFT 2 /* DMIC1R_ENA */
-#define WM8915_DMIC1R_ENA_WIDTH 1 /* DMIC1R_ENA */
-#define WM8915_ADCL_ENA 0x0002 /* ADCL_ENA */
-#define WM8915_ADCL_ENA_MASK 0x0002 /* ADCL_ENA */
-#define WM8915_ADCL_ENA_SHIFT 1 /* ADCL_ENA */
-#define WM8915_ADCL_ENA_WIDTH 1 /* ADCL_ENA */
-#define WM8915_ADCR_ENA 0x0001 /* ADCR_ENA */
-#define WM8915_ADCR_ENA_MASK 0x0001 /* ADCR_ENA */
-#define WM8915_ADCR_ENA_SHIFT 0 /* ADCR_ENA */
-#define WM8915_ADCR_ENA_WIDTH 1 /* ADCR_ENA */
-
-/*
- * R4 (0x04) - Power Management (4)
- */
-#define WM8915_AIF2RX_CHAN1_ENA 0x0200 /* AIF2RX_CHAN1_ENA */
-#define WM8915_AIF2RX_CHAN1_ENA_MASK 0x0200 /* AIF2RX_CHAN1_ENA */
-#define WM8915_AIF2RX_CHAN1_ENA_SHIFT 9 /* AIF2RX_CHAN1_ENA */
-#define WM8915_AIF2RX_CHAN1_ENA_WIDTH 1 /* AIF2RX_CHAN1_ENA */
-#define WM8915_AIF2RX_CHAN0_ENA 0x0100 /* AIF2RX_CHAN0_ENA */
-#define WM8915_AIF2RX_CHAN0_ENA_MASK 0x0100 /* AIF2RX_CHAN0_ENA */
-#define WM8915_AIF2RX_CHAN0_ENA_SHIFT 8 /* AIF2RX_CHAN0_ENA */
-#define WM8915_AIF2RX_CHAN0_ENA_WIDTH 1 /* AIF2RX_CHAN0_ENA */
-#define WM8915_AIF1RX_CHAN5_ENA 0x0020 /* AIF1RX_CHAN5_ENA */
-#define WM8915_AIF1RX_CHAN5_ENA_MASK 0x0020 /* AIF1RX_CHAN5_ENA */
-#define WM8915_AIF1RX_CHAN5_ENA_SHIFT 5 /* AIF1RX_CHAN5_ENA */
-#define WM8915_AIF1RX_CHAN5_ENA_WIDTH 1 /* AIF1RX_CHAN5_ENA */
-#define WM8915_AIF1RX_CHAN4_ENA 0x0010 /* AIF1RX_CHAN4_ENA */
-#define WM8915_AIF1RX_CHAN4_ENA_MASK 0x0010 /* AIF1RX_CHAN4_ENA */
-#define WM8915_AIF1RX_CHAN4_ENA_SHIFT 4 /* AIF1RX_CHAN4_ENA */
-#define WM8915_AIF1RX_CHAN4_ENA_WIDTH 1 /* AIF1RX_CHAN4_ENA */
-#define WM8915_AIF1RX_CHAN3_ENA 0x0008 /* AIF1RX_CHAN3_ENA */
-#define WM8915_AIF1RX_CHAN3_ENA_MASK 0x0008 /* AIF1RX_CHAN3_ENA */
-#define WM8915_AIF1RX_CHAN3_ENA_SHIFT 3 /* AIF1RX_CHAN3_ENA */
-#define WM8915_AIF1RX_CHAN3_ENA_WIDTH 1 /* AIF1RX_CHAN3_ENA */
-#define WM8915_AIF1RX_CHAN2_ENA 0x0004 /* AIF1RX_CHAN2_ENA */
-#define WM8915_AIF1RX_CHAN2_ENA_MASK 0x0004 /* AIF1RX_CHAN2_ENA */
-#define WM8915_AIF1RX_CHAN2_ENA_SHIFT 2 /* AIF1RX_CHAN2_ENA */
-#define WM8915_AIF1RX_CHAN2_ENA_WIDTH 1 /* AIF1RX_CHAN2_ENA */
-#define WM8915_AIF1RX_CHAN1_ENA 0x0002 /* AIF1RX_CHAN1_ENA */
-#define WM8915_AIF1RX_CHAN1_ENA_MASK 0x0002 /* AIF1RX_CHAN1_ENA */
-#define WM8915_AIF1RX_CHAN1_ENA_SHIFT 1 /* AIF1RX_CHAN1_ENA */
-#define WM8915_AIF1RX_CHAN1_ENA_WIDTH 1 /* AIF1RX_CHAN1_ENA */
-#define WM8915_AIF1RX_CHAN0_ENA 0x0001 /* AIF1RX_CHAN0_ENA */
-#define WM8915_AIF1RX_CHAN0_ENA_MASK 0x0001 /* AIF1RX_CHAN0_ENA */
-#define WM8915_AIF1RX_CHAN0_ENA_SHIFT 0 /* AIF1RX_CHAN0_ENA */
-#define WM8915_AIF1RX_CHAN0_ENA_WIDTH 1 /* AIF1RX_CHAN0_ENA */
-
-/*
- * R5 (0x05) - Power Management (5)
- */
-#define WM8915_DSP2TXL_ENA 0x0800 /* DSP2TXL_ENA */
-#define WM8915_DSP2TXL_ENA_MASK 0x0800 /* DSP2TXL_ENA */
-#define WM8915_DSP2TXL_ENA_SHIFT 11 /* DSP2TXL_ENA */
-#define WM8915_DSP2TXL_ENA_WIDTH 1 /* DSP2TXL_ENA */
-#define WM8915_DSP2TXR_ENA 0x0400 /* DSP2TXR_ENA */
-#define WM8915_DSP2TXR_ENA_MASK 0x0400 /* DSP2TXR_ENA */
-#define WM8915_DSP2TXR_ENA_SHIFT 10 /* DSP2TXR_ENA */
-#define WM8915_DSP2TXR_ENA_WIDTH 1 /* DSP2TXR_ENA */
-#define WM8915_DSP1TXL_ENA 0x0200 /* DSP1TXL_ENA */
-#define WM8915_DSP1TXL_ENA_MASK 0x0200 /* DSP1TXL_ENA */
-#define WM8915_DSP1TXL_ENA_SHIFT 9 /* DSP1TXL_ENA */
-#define WM8915_DSP1TXL_ENA_WIDTH 1 /* DSP1TXL_ENA */
-#define WM8915_DSP1TXR_ENA 0x0100 /* DSP1TXR_ENA */
-#define WM8915_DSP1TXR_ENA_MASK 0x0100 /* DSP1TXR_ENA */
-#define WM8915_DSP1TXR_ENA_SHIFT 8 /* DSP1TXR_ENA */
-#define WM8915_DSP1TXR_ENA_WIDTH 1 /* DSP1TXR_ENA */
-#define WM8915_DAC2L_ENA 0x0008 /* DAC2L_ENA */
-#define WM8915_DAC2L_ENA_MASK 0x0008 /* DAC2L_ENA */
-#define WM8915_DAC2L_ENA_SHIFT 3 /* DAC2L_ENA */
-#define WM8915_DAC2L_ENA_WIDTH 1 /* DAC2L_ENA */
-#define WM8915_DAC2R_ENA 0x0004 /* DAC2R_ENA */
-#define WM8915_DAC2R_ENA_MASK 0x0004 /* DAC2R_ENA */
-#define WM8915_DAC2R_ENA_SHIFT 2 /* DAC2R_ENA */
-#define WM8915_DAC2R_ENA_WIDTH 1 /* DAC2R_ENA */
-#define WM8915_DAC1L_ENA 0x0002 /* DAC1L_ENA */
-#define WM8915_DAC1L_ENA_MASK 0x0002 /* DAC1L_ENA */
-#define WM8915_DAC1L_ENA_SHIFT 1 /* DAC1L_ENA */
-#define WM8915_DAC1L_ENA_WIDTH 1 /* DAC1L_ENA */
-#define WM8915_DAC1R_ENA 0x0001 /* DAC1R_ENA */
-#define WM8915_DAC1R_ENA_MASK 0x0001 /* DAC1R_ENA */
-#define WM8915_DAC1R_ENA_SHIFT 0 /* DAC1R_ENA */
-#define WM8915_DAC1R_ENA_WIDTH 1 /* DAC1R_ENA */
-
-/*
- * R6 (0x06) - Power Management (6)
- */
-#define WM8915_AIF2TX_CHAN1_ENA 0x0200 /* AIF2TX_CHAN1_ENA */
-#define WM8915_AIF2TX_CHAN1_ENA_MASK 0x0200 /* AIF2TX_CHAN1_ENA */
-#define WM8915_AIF2TX_CHAN1_ENA_SHIFT 9 /* AIF2TX_CHAN1_ENA */
-#define WM8915_AIF2TX_CHAN1_ENA_WIDTH 1 /* AIF2TX_CHAN1_ENA */
-#define WM8915_AIF2TX_CHAN0_ENA 0x0100 /* AIF2TX_CHAN0_ENA */
-#define WM8915_AIF2TX_CHAN0_ENA_MASK 0x0100 /* AIF2TX_CHAN0_ENA */
-#define WM8915_AIF2TX_CHAN0_ENA_SHIFT 8 /* AIF2TX_CHAN0_ENA */
-#define WM8915_AIF2TX_CHAN0_ENA_WIDTH 1 /* AIF2TX_CHAN0_ENA */
-#define WM8915_AIF1TX_CHAN5_ENA 0x0020 /* AIF1TX_CHAN5_ENA */
-#define WM8915_AIF1TX_CHAN5_ENA_MASK 0x0020 /* AIF1TX_CHAN5_ENA */
-#define WM8915_AIF1TX_CHAN5_ENA_SHIFT 5 /* AIF1TX_CHAN5_ENA */
-#define WM8915_AIF1TX_CHAN5_ENA_WIDTH 1 /* AIF1TX_CHAN5_ENA */
-#define WM8915_AIF1TX_CHAN4_ENA 0x0010 /* AIF1TX_CHAN4_ENA */
-#define WM8915_AIF1TX_CHAN4_ENA_MASK 0x0010 /* AIF1TX_CHAN4_ENA */
-#define WM8915_AIF1TX_CHAN4_ENA_SHIFT 4 /* AIF1TX_CHAN4_ENA */
-#define WM8915_AIF1TX_CHAN4_ENA_WIDTH 1 /* AIF1TX_CHAN4_ENA */
-#define WM8915_AIF1TX_CHAN3_ENA 0x0008 /* AIF1TX_CHAN3_ENA */
-#define WM8915_AIF1TX_CHAN3_ENA_MASK 0x0008 /* AIF1TX_CHAN3_ENA */
-#define WM8915_AIF1TX_CHAN3_ENA_SHIFT 3 /* AIF1TX_CHAN3_ENA */
-#define WM8915_AIF1TX_CHAN3_ENA_WIDTH 1 /* AIF1TX_CHAN3_ENA */
-#define WM8915_AIF1TX_CHAN2_ENA 0x0004 /* AIF1TX_CHAN2_ENA */
-#define WM8915_AIF1TX_CHAN2_ENA_MASK 0x0004 /* AIF1TX_CHAN2_ENA */
-#define WM8915_AIF1TX_CHAN2_ENA_SHIFT 2 /* AIF1TX_CHAN2_ENA */
-#define WM8915_AIF1TX_CHAN2_ENA_WIDTH 1 /* AIF1TX_CHAN2_ENA */
-#define WM8915_AIF1TX_CHAN1_ENA 0x0002 /* AIF1TX_CHAN1_ENA */
-#define WM8915_AIF1TX_CHAN1_ENA_MASK 0x0002 /* AIF1TX_CHAN1_ENA */
-#define WM8915_AIF1TX_CHAN1_ENA_SHIFT 1 /* AIF1TX_CHAN1_ENA */
-#define WM8915_AIF1TX_CHAN1_ENA_WIDTH 1 /* AIF1TX_CHAN1_ENA */
-#define WM8915_AIF1TX_CHAN0_ENA 0x0001 /* AIF1TX_CHAN0_ENA */
-#define WM8915_AIF1TX_CHAN0_ENA_MASK 0x0001 /* AIF1TX_CHAN0_ENA */
-#define WM8915_AIF1TX_CHAN0_ENA_SHIFT 0 /* AIF1TX_CHAN0_ENA */
-#define WM8915_AIF1TX_CHAN0_ENA_WIDTH 1 /* AIF1TX_CHAN0_ENA */
-
-/*
- * R7 (0x07) - Power Management (7)
- */
-#define WM8915_DMIC2_FN 0x0200 /* DMIC2_FN */
-#define WM8915_DMIC2_FN_MASK 0x0200 /* DMIC2_FN */
-#define WM8915_DMIC2_FN_SHIFT 9 /* DMIC2_FN */
-#define WM8915_DMIC2_FN_WIDTH 1 /* DMIC2_FN */
-#define WM8915_DMIC1_FN 0x0100 /* DMIC1_FN */
-#define WM8915_DMIC1_FN_MASK 0x0100 /* DMIC1_FN */
-#define WM8915_DMIC1_FN_SHIFT 8 /* DMIC1_FN */
-#define WM8915_DMIC1_FN_WIDTH 1 /* DMIC1_FN */
-#define WM8915_ADC_DMIC_DSP2R_ENA 0x0080 /* ADC_DMIC_DSP2R_ENA */
-#define WM8915_ADC_DMIC_DSP2R_ENA_MASK 0x0080 /* ADC_DMIC_DSP2R_ENA */
-#define WM8915_ADC_DMIC_DSP2R_ENA_SHIFT 7 /* ADC_DMIC_DSP2R_ENA */
-#define WM8915_ADC_DMIC_DSP2R_ENA_WIDTH 1 /* ADC_DMIC_DSP2R_ENA */
-#define WM8915_ADC_DMIC_DSP2L_ENA 0x0040 /* ADC_DMIC_DSP2L_ENA */
-#define WM8915_ADC_DMIC_DSP2L_ENA_MASK 0x0040 /* ADC_DMIC_DSP2L_ENA */
-#define WM8915_ADC_DMIC_DSP2L_ENA_SHIFT 6 /* ADC_DMIC_DSP2L_ENA */
-#define WM8915_ADC_DMIC_DSP2L_ENA_WIDTH 1 /* ADC_DMIC_DSP2L_ENA */
-#define WM8915_ADC_DMIC_SRC2_MASK 0x0030 /* ADC_DMIC_SRC2 - [5:4] */
-#define WM8915_ADC_DMIC_SRC2_SHIFT 4 /* ADC_DMIC_SRC2 - [5:4] */
-#define WM8915_ADC_DMIC_SRC2_WIDTH 2 /* ADC_DMIC_SRC2 - [5:4] */
-#define WM8915_ADC_DMIC_DSP1R_ENA 0x0008 /* ADC_DMIC_DSP1R_ENA */
-#define WM8915_ADC_DMIC_DSP1R_ENA_MASK 0x0008 /* ADC_DMIC_DSP1R_ENA */
-#define WM8915_ADC_DMIC_DSP1R_ENA_SHIFT 3 /* ADC_DMIC_DSP1R_ENA */
-#define WM8915_ADC_DMIC_DSP1R_ENA_WIDTH 1 /* ADC_DMIC_DSP1R_ENA */
-#define WM8915_ADC_DMIC_DSP1L_ENA 0x0004 /* ADC_DMIC_DSP1L_ENA */
-#define WM8915_ADC_DMIC_DSP1L_ENA_MASK 0x0004 /* ADC_DMIC_DSP1L_ENA */
-#define WM8915_ADC_DMIC_DSP1L_ENA_SHIFT 2 /* ADC_DMIC_DSP1L_ENA */
-#define WM8915_ADC_DMIC_DSP1L_ENA_WIDTH 1 /* ADC_DMIC_DSP1L_ENA */
-#define WM8915_ADC_DMIC_SRC1_MASK 0x0003 /* ADC_DMIC_SRC1 - [1:0] */
-#define WM8915_ADC_DMIC_SRC1_SHIFT 0 /* ADC_DMIC_SRC1 - [1:0] */
-#define WM8915_ADC_DMIC_SRC1_WIDTH 2 /* ADC_DMIC_SRC1 - [1:0] */
-
-/*
- * R8 (0x08) - Power Management (8)
- */
-#define WM8915_AIF2TX_SRC_MASK 0x00C0 /* AIF2TX_SRC - [7:6] */
-#define WM8915_AIF2TX_SRC_SHIFT 6 /* AIF2TX_SRC - [7:6] */
-#define WM8915_AIF2TX_SRC_WIDTH 2 /* AIF2TX_SRC - [7:6] */
-#define WM8915_DSP2RX_SRC 0x0010 /* DSP2RX_SRC */
-#define WM8915_DSP2RX_SRC_MASK 0x0010 /* DSP2RX_SRC */
-#define WM8915_DSP2RX_SRC_SHIFT 4 /* DSP2RX_SRC */
-#define WM8915_DSP2RX_SRC_WIDTH 1 /* DSP2RX_SRC */
-#define WM8915_DSP1RX_SRC 0x0001 /* DSP1RX_SRC */
-#define WM8915_DSP1RX_SRC_MASK 0x0001 /* DSP1RX_SRC */
-#define WM8915_DSP1RX_SRC_SHIFT 0 /* DSP1RX_SRC */
-#define WM8915_DSP1RX_SRC_WIDTH 1 /* DSP1RX_SRC */
-
-/*
- * R16 (0x10) - Left Line Input Volume
- */
-#define WM8915_IN1_VU 0x0080 /* IN1_VU */
-#define WM8915_IN1_VU_MASK 0x0080 /* IN1_VU */
-#define WM8915_IN1_VU_SHIFT 7 /* IN1_VU */
-#define WM8915_IN1_VU_WIDTH 1 /* IN1_VU */
-#define WM8915_IN1L_ZC 0x0020 /* IN1L_ZC */
-#define WM8915_IN1L_ZC_MASK 0x0020 /* IN1L_ZC */
-#define WM8915_IN1L_ZC_SHIFT 5 /* IN1L_ZC */
-#define WM8915_IN1L_ZC_WIDTH 1 /* IN1L_ZC */
-#define WM8915_IN1L_VOL_MASK 0x001F /* IN1L_VOL - [4:0] */
-#define WM8915_IN1L_VOL_SHIFT 0 /* IN1L_VOL - [4:0] */
-#define WM8915_IN1L_VOL_WIDTH 5 /* IN1L_VOL - [4:0] */
-
-/*
- * R17 (0x11) - Right Line Input Volume
- */
-#define WM8915_IN1_VU 0x0080 /* IN1_VU */
-#define WM8915_IN1_VU_MASK 0x0080 /* IN1_VU */
-#define WM8915_IN1_VU_SHIFT 7 /* IN1_VU */
-#define WM8915_IN1_VU_WIDTH 1 /* IN1_VU */
-#define WM8915_IN1R_ZC 0x0020 /* IN1R_ZC */
-#define WM8915_IN1R_ZC_MASK 0x0020 /* IN1R_ZC */
-#define WM8915_IN1R_ZC_SHIFT 5 /* IN1R_ZC */
-#define WM8915_IN1R_ZC_WIDTH 1 /* IN1R_ZC */
-#define WM8915_IN1R_VOL_MASK 0x001F /* IN1R_VOL - [4:0] */
-#define WM8915_IN1R_VOL_SHIFT 0 /* IN1R_VOL - [4:0] */
-#define WM8915_IN1R_VOL_WIDTH 5 /* IN1R_VOL - [4:0] */
-
-/*
- * R18 (0x12) - Line Input Control
- */
-#define WM8915_INL_MODE_MASK 0x000C /* INL_MODE - [3:2] */
-#define WM8915_INL_MODE_SHIFT 2 /* INL_MODE - [3:2] */
-#define WM8915_INL_MODE_WIDTH 2 /* INL_MODE - [3:2] */
-#define WM8915_INR_MODE_MASK 0x0003 /* INR_MODE - [1:0] */
-#define WM8915_INR_MODE_SHIFT 0 /* INR_MODE - [1:0] */
-#define WM8915_INR_MODE_WIDTH 2 /* INR_MODE - [1:0] */
-
-/*
- * R21 (0x15) - DAC1 HPOUT1 Volume
- */
-#define WM8915_DAC1R_HPOUT1R_VOL_MASK 0x00F0 /* DAC1R_HPOUT1R_VOL - [7:4] */
-#define WM8915_DAC1R_HPOUT1R_VOL_SHIFT 4 /* DAC1R_HPOUT1R_VOL - [7:4] */
-#define WM8915_DAC1R_HPOUT1R_VOL_WIDTH 4 /* DAC1R_HPOUT1R_VOL - [7:4] */
-#define WM8915_DAC1L_HPOUT1L_VOL_MASK 0x000F /* DAC1L_HPOUT1L_VOL - [3:0] */
-#define WM8915_DAC1L_HPOUT1L_VOL_SHIFT 0 /* DAC1L_HPOUT1L_VOL - [3:0] */
-#define WM8915_DAC1L_HPOUT1L_VOL_WIDTH 4 /* DAC1L_HPOUT1L_VOL - [3:0] */
-
-/*
- * R22 (0x16) - DAC2 HPOUT2 Volume
- */
-#define WM8915_DAC2R_HPOUT2R_VOL_MASK 0x00F0 /* DAC2R_HPOUT2R_VOL - [7:4] */
-#define WM8915_DAC2R_HPOUT2R_VOL_SHIFT 4 /* DAC2R_HPOUT2R_VOL - [7:4] */
-#define WM8915_DAC2R_HPOUT2R_VOL_WIDTH 4 /* DAC2R_HPOUT2R_VOL - [7:4] */
-#define WM8915_DAC2L_HPOUT2L_VOL_MASK 0x000F /* DAC2L_HPOUT2L_VOL - [3:0] */
-#define WM8915_DAC2L_HPOUT2L_VOL_SHIFT 0 /* DAC2L_HPOUT2L_VOL - [3:0] */
-#define WM8915_DAC2L_HPOUT2L_VOL_WIDTH 4 /* DAC2L_HPOUT2L_VOL - [3:0] */
-
-/*
- * R24 (0x18) - DAC1 Left Volume
- */
-#define WM8915_DAC1L_MUTE 0x0200 /* DAC1L_MUTE */
-#define WM8915_DAC1L_MUTE_MASK 0x0200 /* DAC1L_MUTE */
-#define WM8915_DAC1L_MUTE_SHIFT 9 /* DAC1L_MUTE */
-#define WM8915_DAC1L_MUTE_WIDTH 1 /* DAC1L_MUTE */
-#define WM8915_DAC1_VU 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_MASK 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_SHIFT 8 /* DAC1_VU */
-#define WM8915_DAC1_VU_WIDTH 1 /* DAC1_VU */
-#define WM8915_DAC1L_VOL_MASK 0x00FF /* DAC1L_VOL - [7:0] */
-#define WM8915_DAC1L_VOL_SHIFT 0 /* DAC1L_VOL - [7:0] */
-#define WM8915_DAC1L_VOL_WIDTH 8 /* DAC1L_VOL - [7:0] */
-
-/*
- * R25 (0x19) - DAC1 Right Volume
- */
-#define WM8915_DAC1R_MUTE 0x0200 /* DAC1R_MUTE */
-#define WM8915_DAC1R_MUTE_MASK 0x0200 /* DAC1R_MUTE */
-#define WM8915_DAC1R_MUTE_SHIFT 9 /* DAC1R_MUTE */
-#define WM8915_DAC1R_MUTE_WIDTH 1 /* DAC1R_MUTE */
-#define WM8915_DAC1_VU 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_MASK 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_SHIFT 8 /* DAC1_VU */
-#define WM8915_DAC1_VU_WIDTH 1 /* DAC1_VU */
-#define WM8915_DAC1R_VOL_MASK 0x00FF /* DAC1R_VOL - [7:0] */
-#define WM8915_DAC1R_VOL_SHIFT 0 /* DAC1R_VOL - [7:0] */
-#define WM8915_DAC1R_VOL_WIDTH 8 /* DAC1R_VOL - [7:0] */
-
-/*
- * R26 (0x1A) - DAC2 Left Volume
- */
-#define WM8915_DAC2L_MUTE 0x0200 /* DAC2L_MUTE */
-#define WM8915_DAC2L_MUTE_MASK 0x0200 /* DAC2L_MUTE */
-#define WM8915_DAC2L_MUTE_SHIFT 9 /* DAC2L_MUTE */
-#define WM8915_DAC2L_MUTE_WIDTH 1 /* DAC2L_MUTE */
-#define WM8915_DAC2_VU 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_MASK 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_SHIFT 8 /* DAC2_VU */
-#define WM8915_DAC2_VU_WIDTH 1 /* DAC2_VU */
-#define WM8915_DAC2L_VOL_MASK 0x00FF /* DAC2L_VOL - [7:0] */
-#define WM8915_DAC2L_VOL_SHIFT 0 /* DAC2L_VOL - [7:0] */
-#define WM8915_DAC2L_VOL_WIDTH 8 /* DAC2L_VOL - [7:0] */
-
-/*
- * R27 (0x1B) - DAC2 Right Volume
- */
-#define WM8915_DAC2R_MUTE 0x0200 /* DAC2R_MUTE */
-#define WM8915_DAC2R_MUTE_MASK 0x0200 /* DAC2R_MUTE */
-#define WM8915_DAC2R_MUTE_SHIFT 9 /* DAC2R_MUTE */
-#define WM8915_DAC2R_MUTE_WIDTH 1 /* DAC2R_MUTE */
-#define WM8915_DAC2_VU 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_MASK 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_SHIFT 8 /* DAC2_VU */
-#define WM8915_DAC2_VU_WIDTH 1 /* DAC2_VU */
-#define WM8915_DAC2R_VOL_MASK 0x00FF /* DAC2R_VOL - [7:0] */
-#define WM8915_DAC2R_VOL_SHIFT 0 /* DAC2R_VOL - [7:0] */
-#define WM8915_DAC2R_VOL_WIDTH 8 /* DAC2R_VOL - [7:0] */
-
-/*
- * R28 (0x1C) - Output1 Left Volume
- */
-#define WM8915_DAC1_VU 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_MASK 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_SHIFT 8 /* DAC1_VU */
-#define WM8915_DAC1_VU_WIDTH 1 /* DAC1_VU */
-#define WM8915_HPOUT1L_ZC 0x0080 /* HPOUT1L_ZC */
-#define WM8915_HPOUT1L_ZC_MASK 0x0080 /* HPOUT1L_ZC */
-#define WM8915_HPOUT1L_ZC_SHIFT 7 /* HPOUT1L_ZC */
-#define WM8915_HPOUT1L_ZC_WIDTH 1 /* HPOUT1L_ZC */
-#define WM8915_HPOUT1L_VOL_MASK 0x000F /* HPOUT1L_VOL - [3:0] */
-#define WM8915_HPOUT1L_VOL_SHIFT 0 /* HPOUT1L_VOL - [3:0] */
-#define WM8915_HPOUT1L_VOL_WIDTH 4 /* HPOUT1L_VOL - [3:0] */
-
-/*
- * R29 (0x1D) - Output1 Right Volume
- */
-#define WM8915_DAC1_VU 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_MASK 0x0100 /* DAC1_VU */
-#define WM8915_DAC1_VU_SHIFT 8 /* DAC1_VU */
-#define WM8915_DAC1_VU_WIDTH 1 /* DAC1_VU */
-#define WM8915_HPOUT1R_ZC 0x0080 /* HPOUT1R_ZC */
-#define WM8915_HPOUT1R_ZC_MASK 0x0080 /* HPOUT1R_ZC */
-#define WM8915_HPOUT1R_ZC_SHIFT 7 /* HPOUT1R_ZC */
-#define WM8915_HPOUT1R_ZC_WIDTH 1 /* HPOUT1R_ZC */
-#define WM8915_HPOUT1R_VOL_MASK 0x000F /* HPOUT1R_VOL - [3:0] */
-#define WM8915_HPOUT1R_VOL_SHIFT 0 /* HPOUT1R_VOL - [3:0] */
-#define WM8915_HPOUT1R_VOL_WIDTH 4 /* HPOUT1R_VOL - [3:0] */
-
-/*
- * R30 (0x1E) - Output2 Left Volume
- */
-#define WM8915_DAC2_VU 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_MASK 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_SHIFT 8 /* DAC2_VU */
-#define WM8915_DAC2_VU_WIDTH 1 /* DAC2_VU */
-#define WM8915_HPOUT2L_ZC 0x0080 /* HPOUT2L_ZC */
-#define WM8915_HPOUT2L_ZC_MASK 0x0080 /* HPOUT2L_ZC */
-#define WM8915_HPOUT2L_ZC_SHIFT 7 /* HPOUT2L_ZC */
-#define WM8915_HPOUT2L_ZC_WIDTH 1 /* HPOUT2L_ZC */
-#define WM8915_HPOUT2L_VOL_MASK 0x000F /* HPOUT2L_VOL - [3:0] */
-#define WM8915_HPOUT2L_VOL_SHIFT 0 /* HPOUT2L_VOL - [3:0] */
-#define WM8915_HPOUT2L_VOL_WIDTH 4 /* HPOUT2L_VOL - [3:0] */
-
-/*
- * R31 (0x1F) - Output2 Right Volume
- */
-#define WM8915_DAC2_VU 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_MASK 0x0100 /* DAC2_VU */
-#define WM8915_DAC2_VU_SHIFT 8 /* DAC2_VU */
-#define WM8915_DAC2_VU_WIDTH 1 /* DAC2_VU */
-#define WM8915_HPOUT2R_ZC 0x0080 /* HPOUT2R_ZC */
-#define WM8915_HPOUT2R_ZC_MASK 0x0080 /* HPOUT2R_ZC */
-#define WM8915_HPOUT2R_ZC_SHIFT 7 /* HPOUT2R_ZC */
-#define WM8915_HPOUT2R_ZC_WIDTH 1 /* HPOUT2R_ZC */
-#define WM8915_HPOUT2R_VOL_MASK 0x000F /* HPOUT2R_VOL - [3:0] */
-#define WM8915_HPOUT2R_VOL_SHIFT 0 /* HPOUT2R_VOL - [3:0] */
-#define WM8915_HPOUT2R_VOL_WIDTH 4 /* HPOUT2R_VOL - [3:0] */
-
-/*
- * R32 (0x20) - MICBIAS (1)
- */
-#define WM8915_MICB1_RATE 0x0020 /* MICB1_RATE */
-#define WM8915_MICB1_RATE_MASK 0x0020 /* MICB1_RATE */
-#define WM8915_MICB1_RATE_SHIFT 5 /* MICB1_RATE */
-#define WM8915_MICB1_RATE_WIDTH 1 /* MICB1_RATE */
-#define WM8915_MICB1_MODE 0x0010 /* MICB1_MODE */
-#define WM8915_MICB1_MODE_MASK 0x0010 /* MICB1_MODE */
-#define WM8915_MICB1_MODE_SHIFT 4 /* MICB1_MODE */
-#define WM8915_MICB1_MODE_WIDTH 1 /* MICB1_MODE */
-#define WM8915_MICB1_LVL_MASK 0x000E /* MICB1_LVL - [3:1] */
-#define WM8915_MICB1_LVL_SHIFT 1 /* MICB1_LVL - [3:1] */
-#define WM8915_MICB1_LVL_WIDTH 3 /* MICB1_LVL - [3:1] */
-#define WM8915_MICB1_DISCH 0x0001 /* MICB1_DISCH */
-#define WM8915_MICB1_DISCH_MASK 0x0001 /* MICB1_DISCH */
-#define WM8915_MICB1_DISCH_SHIFT 0 /* MICB1_DISCH */
-#define WM8915_MICB1_DISCH_WIDTH 1 /* MICB1_DISCH */
-
-/*
- * R33 (0x21) - MICBIAS (2)
- */
-#define WM8915_MICB2_RATE 0x0020 /* MICB2_RATE */
-#define WM8915_MICB2_RATE_MASK 0x0020 /* MICB2_RATE */
-#define WM8915_MICB2_RATE_SHIFT 5 /* MICB2_RATE */
-#define WM8915_MICB2_RATE_WIDTH 1 /* MICB2_RATE */
-#define WM8915_MICB2_MODE 0x0010 /* MICB2_MODE */
-#define WM8915_MICB2_MODE_MASK 0x0010 /* MICB2_MODE */
-#define WM8915_MICB2_MODE_SHIFT 4 /* MICB2_MODE */
-#define WM8915_MICB2_MODE_WIDTH 1 /* MICB2_MODE */
-#define WM8915_MICB2_LVL_MASK 0x000E /* MICB2_LVL - [3:1] */
-#define WM8915_MICB2_LVL_SHIFT 1 /* MICB2_LVL - [3:1] */
-#define WM8915_MICB2_LVL_WIDTH 3 /* MICB2_LVL - [3:1] */
-#define WM8915_MICB2_DISCH 0x0001 /* MICB2_DISCH */
-#define WM8915_MICB2_DISCH_MASK 0x0001 /* MICB2_DISCH */
-#define WM8915_MICB2_DISCH_SHIFT 0 /* MICB2_DISCH */
-#define WM8915_MICB2_DISCH_WIDTH 1 /* MICB2_DISCH */
-
-/*
- * R40 (0x28) - LDO 1
- */
-#define WM8915_LDO1_MODE 0x0020 /* LDO1_MODE */
-#define WM8915_LDO1_MODE_MASK 0x0020 /* LDO1_MODE */
-#define WM8915_LDO1_MODE_SHIFT 5 /* LDO1_MODE */
-#define WM8915_LDO1_MODE_WIDTH 1 /* LDO1_MODE */
-#define WM8915_LDO1_VSEL_MASK 0x0006 /* LDO1_VSEL - [2:1] */
-#define WM8915_LDO1_VSEL_SHIFT 1 /* LDO1_VSEL - [2:1] */
-#define WM8915_LDO1_VSEL_WIDTH 2 /* LDO1_VSEL - [2:1] */
-#define WM8915_LDO1_DISCH 0x0001 /* LDO1_DISCH */
-#define WM8915_LDO1_DISCH_MASK 0x0001 /* LDO1_DISCH */
-#define WM8915_LDO1_DISCH_SHIFT 0 /* LDO1_DISCH */
-#define WM8915_LDO1_DISCH_WIDTH 1 /* LDO1_DISCH */
-
-/*
- * R41 (0x29) - LDO 2
- */
-#define WM8915_LDO2_MODE 0x0020 /* LDO2_MODE */
-#define WM8915_LDO2_MODE_MASK 0x0020 /* LDO2_MODE */
-#define WM8915_LDO2_MODE_SHIFT 5 /* LDO2_MODE */
-#define WM8915_LDO2_MODE_WIDTH 1 /* LDO2_MODE */
-#define WM8915_LDO2_VSEL_MASK 0x001E /* LDO2_VSEL - [4:1] */
-#define WM8915_LDO2_VSEL_SHIFT 1 /* LDO2_VSEL - [4:1] */
-#define WM8915_LDO2_VSEL_WIDTH 4 /* LDO2_VSEL - [4:1] */
-#define WM8915_LDO2_DISCH 0x0001 /* LDO2_DISCH */
-#define WM8915_LDO2_DISCH_MASK 0x0001 /* LDO2_DISCH */
-#define WM8915_LDO2_DISCH_SHIFT 0 /* LDO2_DISCH */
-#define WM8915_LDO2_DISCH_WIDTH 1 /* LDO2_DISCH */
-
-/*
- * R48 (0x30) - Accessory Detect Mode 1
- */
-#define WM8915_JD_MODE_MASK 0x0003 /* JD_MODE - [1:0] */
-#define WM8915_JD_MODE_SHIFT 0 /* JD_MODE - [1:0] */
-#define WM8915_JD_MODE_WIDTH 2 /* JD_MODE - [1:0] */
-
-/*
- * R49 (0x31) - Accessory Detect Mode 2
- */
-#define WM8915_HPOUT1FB_SRC 0x0004 /* HPOUT1FB_SRC */
-#define WM8915_HPOUT1FB_SRC_MASK 0x0004 /* HPOUT1FB_SRC */
-#define WM8915_HPOUT1FB_SRC_SHIFT 2 /* HPOUT1FB_SRC */
-#define WM8915_HPOUT1FB_SRC_WIDTH 1 /* HPOUT1FB_SRC */
-#define WM8915_MICD_SRC 0x0002 /* MICD_SRC */
-#define WM8915_MICD_SRC_MASK 0x0002 /* MICD_SRC */
-#define WM8915_MICD_SRC_SHIFT 1 /* MICD_SRC */
-#define WM8915_MICD_SRC_WIDTH 1 /* MICD_SRC */
-#define WM8915_MICD_BIAS_SRC 0x0001 /* MICD_BIAS_SRC */
-#define WM8915_MICD_BIAS_SRC_MASK 0x0001 /* MICD_BIAS_SRC */
-#define WM8915_MICD_BIAS_SRC_SHIFT 0 /* MICD_BIAS_SRC */
-#define WM8915_MICD_BIAS_SRC_WIDTH 1 /* MICD_BIAS_SRC */
-
-/*
- * R52 (0x34) - Headphone Detect 1
- */
-#define WM8915_HP_HOLDTIME_MASK 0x00E0 /* HP_HOLDTIME - [7:5] */
-#define WM8915_HP_HOLDTIME_SHIFT 5 /* HP_HOLDTIME - [7:5] */
-#define WM8915_HP_HOLDTIME_WIDTH 3 /* HP_HOLDTIME - [7:5] */
-#define WM8915_HP_CLK_DIV_MASK 0x0018 /* HP_CLK_DIV - [4:3] */
-#define WM8915_HP_CLK_DIV_SHIFT 3 /* HP_CLK_DIV - [4:3] */
-#define WM8915_HP_CLK_DIV_WIDTH 2 /* HP_CLK_DIV - [4:3] */
-#define WM8915_HP_STEP_SIZE 0x0002 /* HP_STEP_SIZE */
-#define WM8915_HP_STEP_SIZE_MASK 0x0002 /* HP_STEP_SIZE */
-#define WM8915_HP_STEP_SIZE_SHIFT 1 /* HP_STEP_SIZE */
-#define WM8915_HP_STEP_SIZE_WIDTH 1 /* HP_STEP_SIZE */
-#define WM8915_HP_POLL 0x0001 /* HP_POLL */
-#define WM8915_HP_POLL_MASK 0x0001 /* HP_POLL */
-#define WM8915_HP_POLL_SHIFT 0 /* HP_POLL */
-#define WM8915_HP_POLL_WIDTH 1 /* HP_POLL */
-
-/*
- * R53 (0x35) - Headphone Detect 2
- */
-#define WM8915_HP_DONE 0x0080 /* HP_DONE */
-#define WM8915_HP_DONE_MASK 0x0080 /* HP_DONE */
-#define WM8915_HP_DONE_SHIFT 7 /* HP_DONE */
-#define WM8915_HP_DONE_WIDTH 1 /* HP_DONE */
-#define WM8915_HP_LVL_MASK 0x007F /* HP_LVL - [6:0] */
-#define WM8915_HP_LVL_SHIFT 0 /* HP_LVL - [6:0] */
-#define WM8915_HP_LVL_WIDTH 7 /* HP_LVL - [6:0] */
-
-/*
- * R56 (0x38) - Mic Detect 1
- */
-#define WM8915_MICD_BIAS_STARTTIME_MASK 0xF000 /* MICD_BIAS_STARTTIME - [15:12] */
-#define WM8915_MICD_BIAS_STARTTIME_SHIFT 12 /* MICD_BIAS_STARTTIME - [15:12] */
-#define WM8915_MICD_BIAS_STARTTIME_WIDTH 4 /* MICD_BIAS_STARTTIME - [15:12] */
-#define WM8915_MICD_RATE_MASK 0x0F00 /* MICD_RATE - [11:8] */
-#define WM8915_MICD_RATE_SHIFT 8 /* MICD_RATE - [11:8] */
-#define WM8915_MICD_RATE_WIDTH 4 /* MICD_RATE - [11:8] */
-#define WM8915_MICD_DBTIME 0x0002 /* MICD_DBTIME */
-#define WM8915_MICD_DBTIME_MASK 0x0002 /* MICD_DBTIME */
-#define WM8915_MICD_DBTIME_SHIFT 1 /* MICD_DBTIME */
-#define WM8915_MICD_DBTIME_WIDTH 1 /* MICD_DBTIME */
-#define WM8915_MICD_ENA 0x0001 /* MICD_ENA */
-#define WM8915_MICD_ENA_MASK 0x0001 /* MICD_ENA */
-#define WM8915_MICD_ENA_SHIFT 0 /* MICD_ENA */
-#define WM8915_MICD_ENA_WIDTH 1 /* MICD_ENA */
-
-/*
- * R57 (0x39) - Mic Detect 2
- */
-#define WM8915_MICD_LVL_SEL_MASK 0x00FF /* MICD_LVL_SEL - [7:0] */
-#define WM8915_MICD_LVL_SEL_SHIFT 0 /* MICD_LVL_SEL - [7:0] */
-#define WM8915_MICD_LVL_SEL_WIDTH 8 /* MICD_LVL_SEL - [7:0] */
-
-/*
- * R58 (0x3A) - Mic Detect 3
- */
-#define WM8915_MICD_LVL_MASK 0x07FC /* MICD_LVL - [10:2] */
-#define WM8915_MICD_LVL_SHIFT 2 /* MICD_LVL - [10:2] */
-#define WM8915_MICD_LVL_WIDTH 9 /* MICD_LVL - [10:2] */
-#define WM8915_MICD_VALID 0x0002 /* MICD_VALID */
-#define WM8915_MICD_VALID_MASK 0x0002 /* MICD_VALID */
-#define WM8915_MICD_VALID_SHIFT 1 /* MICD_VALID */
-#define WM8915_MICD_VALID_WIDTH 1 /* MICD_VALID */
-#define WM8915_MICD_STS 0x0001 /* MICD_STS */
-#define WM8915_MICD_STS_MASK 0x0001 /* MICD_STS */
-#define WM8915_MICD_STS_SHIFT 0 /* MICD_STS */
-#define WM8915_MICD_STS_WIDTH 1 /* MICD_STS */
-
-/*
- * R64 (0x40) - Charge Pump (1)
- */
-#define WM8915_CP_ENA 0x8000 /* CP_ENA */
-#define WM8915_CP_ENA_MASK 0x8000 /* CP_ENA */
-#define WM8915_CP_ENA_SHIFT 15 /* CP_ENA */
-#define WM8915_CP_ENA_WIDTH 1 /* CP_ENA */
-
-/*
- * R65 (0x41) - Charge Pump (2)
- */
-#define WM8915_CP_DISCH 0x8000 /* CP_DISCH */
-#define WM8915_CP_DISCH_MASK 0x8000 /* CP_DISCH */
-#define WM8915_CP_DISCH_SHIFT 15 /* CP_DISCH */
-#define WM8915_CP_DISCH_WIDTH 1 /* CP_DISCH */
-
-/*
- * R80 (0x50) - DC Servo (1)
- */
-#define WM8915_DCS_ENA_CHAN_3 0x0008 /* DCS_ENA_CHAN_3 */
-#define WM8915_DCS_ENA_CHAN_3_MASK 0x0008 /* DCS_ENA_CHAN_3 */
-#define WM8915_DCS_ENA_CHAN_3_SHIFT 3 /* DCS_ENA_CHAN_3 */
-#define WM8915_DCS_ENA_CHAN_3_WIDTH 1 /* DCS_ENA_CHAN_3 */
-#define WM8915_DCS_ENA_CHAN_2 0x0004 /* DCS_ENA_CHAN_2 */
-#define WM8915_DCS_ENA_CHAN_2_MASK 0x0004 /* DCS_ENA_CHAN_2 */
-#define WM8915_DCS_ENA_CHAN_2_SHIFT 2 /* DCS_ENA_CHAN_2 */
-#define WM8915_DCS_ENA_CHAN_2_WIDTH 1 /* DCS_ENA_CHAN_2 */
-#define WM8915_DCS_ENA_CHAN_1 0x0002 /* DCS_ENA_CHAN_1 */
-#define WM8915_DCS_ENA_CHAN_1_MASK 0x0002 /* DCS_ENA_CHAN_1 */
-#define WM8915_DCS_ENA_CHAN_1_SHIFT 1 /* DCS_ENA_CHAN_1 */
-#define WM8915_DCS_ENA_CHAN_1_WIDTH 1 /* DCS_ENA_CHAN_1 */
-#define WM8915_DCS_ENA_CHAN_0 0x0001 /* DCS_ENA_CHAN_0 */
-#define WM8915_DCS_ENA_CHAN_0_MASK 0x0001 /* DCS_ENA_CHAN_0 */
-#define WM8915_DCS_ENA_CHAN_0_SHIFT 0 /* DCS_ENA_CHAN_0 */
-#define WM8915_DCS_ENA_CHAN_0_WIDTH 1 /* DCS_ENA_CHAN_0 */
-
-/*
- * R81 (0x51) - DC Servo (2)
- */
-#define WM8915_DCS_TRIG_SINGLE_3 0x8000 /* DCS_TRIG_SINGLE_3 */
-#define WM8915_DCS_TRIG_SINGLE_3_MASK 0x8000 /* DCS_TRIG_SINGLE_3 */
-#define WM8915_DCS_TRIG_SINGLE_3_SHIFT 15 /* DCS_TRIG_SINGLE_3 */
-#define WM8915_DCS_TRIG_SINGLE_3_WIDTH 1 /* DCS_TRIG_SINGLE_3 */
-#define WM8915_DCS_TRIG_SINGLE_2 0x4000 /* DCS_TRIG_SINGLE_2 */
-#define WM8915_DCS_TRIG_SINGLE_2_MASK 0x4000 /* DCS_TRIG_SINGLE_2 */
-#define WM8915_DCS_TRIG_SINGLE_2_SHIFT 14 /* DCS_TRIG_SINGLE_2 */
-#define WM8915_DCS_TRIG_SINGLE_2_WIDTH 1 /* DCS_TRIG_SINGLE_2 */
-#define WM8915_DCS_TRIG_SINGLE_1 0x2000 /* DCS_TRIG_SINGLE_1 */
-#define WM8915_DCS_TRIG_SINGLE_1_MASK 0x2000 /* DCS_TRIG_SINGLE_1 */
-#define WM8915_DCS_TRIG_SINGLE_1_SHIFT 13 /* DCS_TRIG_SINGLE_1 */
-#define WM8915_DCS_TRIG_SINGLE_1_WIDTH 1 /* DCS_TRIG_SINGLE_1 */
-#define WM8915_DCS_TRIG_SINGLE_0 0x1000 /* DCS_TRIG_SINGLE_0 */
-#define WM8915_DCS_TRIG_SINGLE_0_MASK 0x1000 /* DCS_TRIG_SINGLE_0 */
-#define WM8915_DCS_TRIG_SINGLE_0_SHIFT 12 /* DCS_TRIG_SINGLE_0 */
-#define WM8915_DCS_TRIG_SINGLE_0_WIDTH 1 /* DCS_TRIG_SINGLE_0 */
-#define WM8915_DCS_TRIG_SERIES_3 0x0800 /* DCS_TRIG_SERIES_3 */
-#define WM8915_DCS_TRIG_SERIES_3_MASK 0x0800 /* DCS_TRIG_SERIES_3 */
-#define WM8915_DCS_TRIG_SERIES_3_SHIFT 11 /* DCS_TRIG_SERIES_3 */
-#define WM8915_DCS_TRIG_SERIES_3_WIDTH 1 /* DCS_TRIG_SERIES_3 */
-#define WM8915_DCS_TRIG_SERIES_2 0x0400 /* DCS_TRIG_SERIES_2 */
-#define WM8915_DCS_TRIG_SERIES_2_MASK 0x0400 /* DCS_TRIG_SERIES_2 */
-#define WM8915_DCS_TRIG_SERIES_2_SHIFT 10 /* DCS_TRIG_SERIES_2 */
-#define WM8915_DCS_TRIG_SERIES_2_WIDTH 1 /* DCS_TRIG_SERIES_2 */
-#define WM8915_DCS_TRIG_SERIES_1 0x0200 /* DCS_TRIG_SERIES_1 */
-#define WM8915_DCS_TRIG_SERIES_1_MASK 0x0200 /* DCS_TRIG_SERIES_1 */
-#define WM8915_DCS_TRIG_SERIES_1_SHIFT 9 /* DCS_TRIG_SERIES_1 */
-#define WM8915_DCS_TRIG_SERIES_1_WIDTH 1 /* DCS_TRIG_SERIES_1 */
-#define WM8915_DCS_TRIG_SERIES_0 0x0100 /* DCS_TRIG_SERIES_0 */
-#define WM8915_DCS_TRIG_SERIES_0_MASK 0x0100 /* DCS_TRIG_SERIES_0 */
-#define WM8915_DCS_TRIG_SERIES_0_SHIFT 8 /* DCS_TRIG_SERIES_0 */
-#define WM8915_DCS_TRIG_SERIES_0_WIDTH 1 /* DCS_TRIG_SERIES_0 */
-#define WM8915_DCS_TRIG_STARTUP_3 0x0080 /* DCS_TRIG_STARTUP_3 */
-#define WM8915_DCS_TRIG_STARTUP_3_MASK 0x0080 /* DCS_TRIG_STARTUP_3 */
-#define WM8915_DCS_TRIG_STARTUP_3_SHIFT 7 /* DCS_TRIG_STARTUP_3 */
-#define WM8915_DCS_TRIG_STARTUP_3_WIDTH 1 /* DCS_TRIG_STARTUP_3 */
-#define WM8915_DCS_TRIG_STARTUP_2 0x0040 /* DCS_TRIG_STARTUP_2 */
-#define WM8915_DCS_TRIG_STARTUP_2_MASK 0x0040 /* DCS_TRIG_STARTUP_2 */
-#define WM8915_DCS_TRIG_STARTUP_2_SHIFT 6 /* DCS_TRIG_STARTUP_2 */
-#define WM8915_DCS_TRIG_STARTUP_2_WIDTH 1 /* DCS_TRIG_STARTUP_2 */
-#define WM8915_DCS_TRIG_STARTUP_1 0x0020 /* DCS_TRIG_STARTUP_1 */
-#define WM8915_DCS_TRIG_STARTUP_1_MASK 0x0020 /* DCS_TRIG_STARTUP_1 */
-#define WM8915_DCS_TRIG_STARTUP_1_SHIFT 5 /* DCS_TRIG_STARTUP_1 */
-#define WM8915_DCS_TRIG_STARTUP_1_WIDTH 1 /* DCS_TRIG_STARTUP_1 */
-#define WM8915_DCS_TRIG_STARTUP_0 0x0010 /* DCS_TRIG_STARTUP_0 */
-#define WM8915_DCS_TRIG_STARTUP_0_MASK 0x0010 /* DCS_TRIG_STARTUP_0 */
-#define WM8915_DCS_TRIG_STARTUP_0_SHIFT 4 /* DCS_TRIG_STARTUP_0 */
-#define WM8915_DCS_TRIG_STARTUP_0_WIDTH 1 /* DCS_TRIG_STARTUP_0 */
-#define WM8915_DCS_TRIG_DAC_WR_3 0x0008 /* DCS_TRIG_DAC_WR_3 */
-#define WM8915_DCS_TRIG_DAC_WR_3_MASK 0x0008 /* DCS_TRIG_DAC_WR_3 */
-#define WM8915_DCS_TRIG_DAC_WR_3_SHIFT 3 /* DCS_TRIG_DAC_WR_3 */
-#define WM8915_DCS_TRIG_DAC_WR_3_WIDTH 1 /* DCS_TRIG_DAC_WR_3 */
-#define WM8915_DCS_TRIG_DAC_WR_2 0x0004 /* DCS_TRIG_DAC_WR_2 */
-#define WM8915_DCS_TRIG_DAC_WR_2_MASK 0x0004 /* DCS_TRIG_DAC_WR_2 */
-#define WM8915_DCS_TRIG_DAC_WR_2_SHIFT 2 /* DCS_TRIG_DAC_WR_2 */
-#define WM8915_DCS_TRIG_DAC_WR_2_WIDTH 1 /* DCS_TRIG_DAC_WR_2 */
-#define WM8915_DCS_TRIG_DAC_WR_1 0x0002 /* DCS_TRIG_DAC_WR_1 */
-#define WM8915_DCS_TRIG_DAC_WR_1_MASK 0x0002 /* DCS_TRIG_DAC_WR_1 */
-#define WM8915_DCS_TRIG_DAC_WR_1_SHIFT 1 /* DCS_TRIG_DAC_WR_1 */
-#define WM8915_DCS_TRIG_DAC_WR_1_WIDTH 1 /* DCS_TRIG_DAC_WR_1 */
-#define WM8915_DCS_TRIG_DAC_WR_0 0x0001 /* DCS_TRIG_DAC_WR_0 */
-#define WM8915_DCS_TRIG_DAC_WR_0_MASK 0x0001 /* DCS_TRIG_DAC_WR_0 */
-#define WM8915_DCS_TRIG_DAC_WR_0_SHIFT 0 /* DCS_TRIG_DAC_WR_0 */
-#define WM8915_DCS_TRIG_DAC_WR_0_WIDTH 1 /* DCS_TRIG_DAC_WR_0 */
-
-/*
- * R82 (0x52) - DC Servo (3)
- */
-#define WM8915_DCS_TIMER_PERIOD_23_MASK 0x0F00 /* DCS_TIMER_PERIOD_23 - [11:8] */
-#define WM8915_DCS_TIMER_PERIOD_23_SHIFT 8 /* DCS_TIMER_PERIOD_23 - [11:8] */
-#define WM8915_DCS_TIMER_PERIOD_23_WIDTH 4 /* DCS_TIMER_PERIOD_23 - [11:8] */
-#define WM8915_DCS_TIMER_PERIOD_01_MASK 0x000F /* DCS_TIMER_PERIOD_01 - [3:0] */
-#define WM8915_DCS_TIMER_PERIOD_01_SHIFT 0 /* DCS_TIMER_PERIOD_01 - [3:0] */
-#define WM8915_DCS_TIMER_PERIOD_01_WIDTH 4 /* DCS_TIMER_PERIOD_01 - [3:0] */
-
-/*
- * R84 (0x54) - DC Servo (5)
- */
-#define WM8915_DCS_SERIES_NO_23_MASK 0x7F00 /* DCS_SERIES_NO_23 - [14:8] */
-#define WM8915_DCS_SERIES_NO_23_SHIFT 8 /* DCS_SERIES_NO_23 - [14:8] */
-#define WM8915_DCS_SERIES_NO_23_WIDTH 7 /* DCS_SERIES_NO_23 - [14:8] */
-#define WM8915_DCS_SERIES_NO_01_MASK 0x007F /* DCS_SERIES_NO_01 - [6:0] */
-#define WM8915_DCS_SERIES_NO_01_SHIFT 0 /* DCS_SERIES_NO_01 - [6:0] */
-#define WM8915_DCS_SERIES_NO_01_WIDTH 7 /* DCS_SERIES_NO_01 - [6:0] */
-
-/*
- * R85 (0x55) - DC Servo (6)
- */
-#define WM8915_DCS_DAC_WR_VAL_3_MASK 0xFF00 /* DCS_DAC_WR_VAL_3 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_3_SHIFT 8 /* DCS_DAC_WR_VAL_3 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_3_WIDTH 8 /* DCS_DAC_WR_VAL_3 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_2_MASK 0x00FF /* DCS_DAC_WR_VAL_2 - [7:0] */
-#define WM8915_DCS_DAC_WR_VAL_2_SHIFT 0 /* DCS_DAC_WR_VAL_2 - [7:0] */
-#define WM8915_DCS_DAC_WR_VAL_2_WIDTH 8 /* DCS_DAC_WR_VAL_2 - [7:0] */
-
-/*
- * R86 (0x56) - DC Servo (7)
- */
-#define WM8915_DCS_DAC_WR_VAL_1_MASK 0xFF00 /* DCS_DAC_WR_VAL_1 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_1_SHIFT 8 /* DCS_DAC_WR_VAL_1 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_1_WIDTH 8 /* DCS_DAC_WR_VAL_1 - [15:8] */
-#define WM8915_DCS_DAC_WR_VAL_0_MASK 0x00FF /* DCS_DAC_WR_VAL_0 - [7:0] */
-#define WM8915_DCS_DAC_WR_VAL_0_SHIFT 0 /* DCS_DAC_WR_VAL_0 - [7:0] */
-#define WM8915_DCS_DAC_WR_VAL_0_WIDTH 8 /* DCS_DAC_WR_VAL_0 - [7:0] */
-
-/*
- * R87 (0x57) - DC Servo Readback 0
- */
-#define WM8915_DCS_CAL_COMPLETE_MASK 0x0F00 /* DCS_CAL_COMPLETE - [11:8] */
-#define WM8915_DCS_CAL_COMPLETE_SHIFT 8 /* DCS_CAL_COMPLETE - [11:8] */
-#define WM8915_DCS_CAL_COMPLETE_WIDTH 4 /* DCS_CAL_COMPLETE - [11:8] */
-#define WM8915_DCS_DAC_WR_COMPLETE_MASK 0x00F0 /* DCS_DAC_WR_COMPLETE - [7:4] */
-#define WM8915_DCS_DAC_WR_COMPLETE_SHIFT 4 /* DCS_DAC_WR_COMPLETE - [7:4] */
-#define WM8915_DCS_DAC_WR_COMPLETE_WIDTH 4 /* DCS_DAC_WR_COMPLETE - [7:4] */
-#define WM8915_DCS_STARTUP_COMPLETE_MASK 0x000F /* DCS_STARTUP_COMPLETE - [3:0] */
-#define WM8915_DCS_STARTUP_COMPLETE_SHIFT 0 /* DCS_STARTUP_COMPLETE - [3:0] */
-#define WM8915_DCS_STARTUP_COMPLETE_WIDTH 4 /* DCS_STARTUP_COMPLETE - [3:0] */
-
-/*
- * R96 (0x60) - Analogue HP (1)
- */
-#define WM8915_HPOUT1L_RMV_SHORT 0x0080 /* HPOUT1L_RMV_SHORT */
-#define WM8915_HPOUT1L_RMV_SHORT_MASK 0x0080 /* HPOUT1L_RMV_SHORT */
-#define WM8915_HPOUT1L_RMV_SHORT_SHIFT 7 /* HPOUT1L_RMV_SHORT */
-#define WM8915_HPOUT1L_RMV_SHORT_WIDTH 1 /* HPOUT1L_RMV_SHORT */
-#define WM8915_HPOUT1L_OUTP 0x0040 /* HPOUT1L_OUTP */
-#define WM8915_HPOUT1L_OUTP_MASK 0x0040 /* HPOUT1L_OUTP */
-#define WM8915_HPOUT1L_OUTP_SHIFT 6 /* HPOUT1L_OUTP */
-#define WM8915_HPOUT1L_OUTP_WIDTH 1 /* HPOUT1L_OUTP */
-#define WM8915_HPOUT1L_DLY 0x0020 /* HPOUT1L_DLY */
-#define WM8915_HPOUT1L_DLY_MASK 0x0020 /* HPOUT1L_DLY */
-#define WM8915_HPOUT1L_DLY_SHIFT 5 /* HPOUT1L_DLY */
-#define WM8915_HPOUT1L_DLY_WIDTH 1 /* HPOUT1L_DLY */
-#define WM8915_HPOUT1R_RMV_SHORT 0x0008 /* HPOUT1R_RMV_SHORT */
-#define WM8915_HPOUT1R_RMV_SHORT_MASK 0x0008 /* HPOUT1R_RMV_SHORT */
-#define WM8915_HPOUT1R_RMV_SHORT_SHIFT 3 /* HPOUT1R_RMV_SHORT */
-#define WM8915_HPOUT1R_RMV_SHORT_WIDTH 1 /* HPOUT1R_RMV_SHORT */
-#define WM8915_HPOUT1R_OUTP 0x0004 /* HPOUT1R_OUTP */
-#define WM8915_HPOUT1R_OUTP_MASK 0x0004 /* HPOUT1R_OUTP */
-#define WM8915_HPOUT1R_OUTP_SHIFT 2 /* HPOUT1R_OUTP */
-#define WM8915_HPOUT1R_OUTP_WIDTH 1 /* HPOUT1R_OUTP */
-#define WM8915_HPOUT1R_DLY 0x0002 /* HPOUT1R_DLY */
-#define WM8915_HPOUT1R_DLY_MASK 0x0002 /* HPOUT1R_DLY */
-#define WM8915_HPOUT1R_DLY_SHIFT 1 /* HPOUT1R_DLY */
-#define WM8915_HPOUT1R_DLY_WIDTH 1 /* HPOUT1R_DLY */
-
-/*
- * R97 (0x61) - Analogue HP (2)
- */
-#define WM8915_HPOUT2L_RMV_SHORT 0x0080 /* HPOUT2L_RMV_SHORT */
-#define WM8915_HPOUT2L_RMV_SHORT_MASK 0x0080 /* HPOUT2L_RMV_SHORT */
-#define WM8915_HPOUT2L_RMV_SHORT_SHIFT 7 /* HPOUT2L_RMV_SHORT */
-#define WM8915_HPOUT2L_RMV_SHORT_WIDTH 1 /* HPOUT2L_RMV_SHORT */
-#define WM8915_HPOUT2L_OUTP 0x0040 /* HPOUT2L_OUTP */
-#define WM8915_HPOUT2L_OUTP_MASK 0x0040 /* HPOUT2L_OUTP */
-#define WM8915_HPOUT2L_OUTP_SHIFT 6 /* HPOUT2L_OUTP */
-#define WM8915_HPOUT2L_OUTP_WIDTH 1 /* HPOUT2L_OUTP */
-#define WM8915_HPOUT2L_DLY 0x0020 /* HPOUT2L_DLY */
-#define WM8915_HPOUT2L_DLY_MASK 0x0020 /* HPOUT2L_DLY */
-#define WM8915_HPOUT2L_DLY_SHIFT 5 /* HPOUT2L_DLY */
-#define WM8915_HPOUT2L_DLY_WIDTH 1 /* HPOUT2L_DLY */
-#define WM8915_HPOUT2R_RMV_SHORT 0x0008 /* HPOUT2R_RMV_SHORT */
-#define WM8915_HPOUT2R_RMV_SHORT_MASK 0x0008 /* HPOUT2R_RMV_SHORT */
-#define WM8915_HPOUT2R_RMV_SHORT_SHIFT 3 /* HPOUT2R_RMV_SHORT */
-#define WM8915_HPOUT2R_RMV_SHORT_WIDTH 1 /* HPOUT2R_RMV_SHORT */
-#define WM8915_HPOUT2R_OUTP 0x0004 /* HPOUT2R_OUTP */
-#define WM8915_HPOUT2R_OUTP_MASK 0x0004 /* HPOUT2R_OUTP */
-#define WM8915_HPOUT2R_OUTP_SHIFT 2 /* HPOUT2R_OUTP */
-#define WM8915_HPOUT2R_OUTP_WIDTH 1 /* HPOUT2R_OUTP */
-#define WM8915_HPOUT2R_DLY 0x0002 /* HPOUT2R_DLY */
-#define WM8915_HPOUT2R_DLY_MASK 0x0002 /* HPOUT2R_DLY */
-#define WM8915_HPOUT2R_DLY_SHIFT 1 /* HPOUT2R_DLY */
-#define WM8915_HPOUT2R_DLY_WIDTH 1 /* HPOUT2R_DLY */
-
-/*
- * R256 (0x100) - Chip Revision
- */
-#define WM8915_CHIP_REV_MASK 0x000F /* CHIP_REV - [3:0] */
-#define WM8915_CHIP_REV_SHIFT 0 /* CHIP_REV - [3:0] */
-#define WM8915_CHIP_REV_WIDTH 4 /* CHIP_REV - [3:0] */
-
-/*
- * R257 (0x101) - Control Interface (1)
- */
-#define WM8915_AUTO_INC 0x0004 /* AUTO_INC */
-#define WM8915_AUTO_INC_MASK 0x0004 /* AUTO_INC */
-#define WM8915_AUTO_INC_SHIFT 2 /* AUTO_INC */
-#define WM8915_AUTO_INC_WIDTH 1 /* AUTO_INC */
-
-/*
- * R272 (0x110) - Write Sequencer Ctrl (1)
- */
-#define WM8915_WSEQ_ENA 0x8000 /* WSEQ_ENA */
-#define WM8915_WSEQ_ENA_MASK 0x8000 /* WSEQ_ENA */
-#define WM8915_WSEQ_ENA_SHIFT 15 /* WSEQ_ENA */
-#define WM8915_WSEQ_ENA_WIDTH 1 /* WSEQ_ENA */
-#define WM8915_WSEQ_ABORT 0x0200 /* WSEQ_ABORT */
-#define WM8915_WSEQ_ABORT_MASK 0x0200 /* WSEQ_ABORT */
-#define WM8915_WSEQ_ABORT_SHIFT 9 /* WSEQ_ABORT */
-#define WM8915_WSEQ_ABORT_WIDTH 1 /* WSEQ_ABORT */
-#define WM8915_WSEQ_START 0x0100 /* WSEQ_START */
-#define WM8915_WSEQ_START_MASK 0x0100 /* WSEQ_START */
-#define WM8915_WSEQ_START_SHIFT 8 /* WSEQ_START */
-#define WM8915_WSEQ_START_WIDTH 1 /* WSEQ_START */
-#define WM8915_WSEQ_START_INDEX_MASK 0x007F /* WSEQ_START_INDEX - [6:0] */
-#define WM8915_WSEQ_START_INDEX_SHIFT 0 /* WSEQ_START_INDEX - [6:0] */
-#define WM8915_WSEQ_START_INDEX_WIDTH 7 /* WSEQ_START_INDEX - [6:0] */
-
-/*
- * R273 (0x111) - Write Sequencer Ctrl (2)
- */
-#define WM8915_WSEQ_BUSY 0x0100 /* WSEQ_BUSY */
-#define WM8915_WSEQ_BUSY_MASK 0x0100 /* WSEQ_BUSY */
-#define WM8915_WSEQ_BUSY_SHIFT 8 /* WSEQ_BUSY */
-#define WM8915_WSEQ_BUSY_WIDTH 1 /* WSEQ_BUSY */
-#define WM8915_WSEQ_CURRENT_INDEX_MASK 0x007F /* WSEQ_CURRENT_INDEX - [6:0] */
-#define WM8915_WSEQ_CURRENT_INDEX_SHIFT 0 /* WSEQ_CURRENT_INDEX - [6:0] */
-#define WM8915_WSEQ_CURRENT_INDEX_WIDTH 7 /* WSEQ_CURRENT_INDEX - [6:0] */
-
-/*
- * R512 (0x200) - AIF Clocking (1)
- */
-#define WM8915_SYSCLK_SRC_MASK 0x0018 /* SYSCLK_SRC - [4:3] */
-#define WM8915_SYSCLK_SRC_SHIFT 3 /* SYSCLK_SRC - [4:3] */
-#define WM8915_SYSCLK_SRC_WIDTH 2 /* SYSCLK_SRC - [4:3] */
-#define WM8915_SYSCLK_INV 0x0004 /* SYSCLK_INV */
-#define WM8915_SYSCLK_INV_MASK 0x0004 /* SYSCLK_INV */
-#define WM8915_SYSCLK_INV_SHIFT 2 /* SYSCLK_INV */
-#define WM8915_SYSCLK_INV_WIDTH 1 /* SYSCLK_INV */
-#define WM8915_SYSCLK_DIV 0x0002 /* SYSCLK_DIV */
-#define WM8915_SYSCLK_DIV_MASK 0x0002 /* SYSCLK_DIV */
-#define WM8915_SYSCLK_DIV_SHIFT 1 /* SYSCLK_DIV */
-#define WM8915_SYSCLK_DIV_WIDTH 1 /* SYSCLK_DIV */
-#define WM8915_SYSCLK_ENA 0x0001 /* SYSCLK_ENA */
-#define WM8915_SYSCLK_ENA_MASK 0x0001 /* SYSCLK_ENA */
-#define WM8915_SYSCLK_ENA_SHIFT 0 /* SYSCLK_ENA */
-#define WM8915_SYSCLK_ENA_WIDTH 1 /* SYSCLK_ENA */
-
-/*
- * R513 (0x201) - AIF Clocking (2)
- */
-#define WM8915_DSP2_DIV_MASK 0x0018 /* DSP2_DIV - [4:3] */
-#define WM8915_DSP2_DIV_SHIFT 3 /* DSP2_DIV - [4:3] */
-#define WM8915_DSP2_DIV_WIDTH 2 /* DSP2_DIV - [4:3] */
-#define WM8915_DSP1_DIV_MASK 0x0003 /* DSP1_DIV - [1:0] */
-#define WM8915_DSP1_DIV_SHIFT 0 /* DSP1_DIV - [1:0] */
-#define WM8915_DSP1_DIV_WIDTH 2 /* DSP1_DIV - [1:0] */
-
-/*
- * R520 (0x208) - Clocking (1)
- */
-#define WM8915_LFCLK_ENA 0x0020 /* LFCLK_ENA */
-#define WM8915_LFCLK_ENA_MASK 0x0020 /* LFCLK_ENA */
-#define WM8915_LFCLK_ENA_SHIFT 5 /* LFCLK_ENA */
-#define WM8915_LFCLK_ENA_WIDTH 1 /* LFCLK_ENA */
-#define WM8915_TOCLK_ENA 0x0010 /* TOCLK_ENA */
-#define WM8915_TOCLK_ENA_MASK 0x0010 /* TOCLK_ENA */
-#define WM8915_TOCLK_ENA_SHIFT 4 /* TOCLK_ENA */
-#define WM8915_TOCLK_ENA_WIDTH 1 /* TOCLK_ENA */
-#define WM8915_AIFCLK_ENA 0x0004 /* AIFCLK_ENA */
-#define WM8915_AIFCLK_ENA_MASK 0x0004 /* AIFCLK_ENA */
-#define WM8915_AIFCLK_ENA_SHIFT 2 /* AIFCLK_ENA */
-#define WM8915_AIFCLK_ENA_WIDTH 1 /* AIFCLK_ENA */
-#define WM8915_SYSDSPCLK_ENA 0x0002 /* SYSDSPCLK_ENA */
-#define WM8915_SYSDSPCLK_ENA_MASK 0x0002 /* SYSDSPCLK_ENA */
-#define WM8915_SYSDSPCLK_ENA_SHIFT 1 /* SYSDSPCLK_ENA */
-#define WM8915_SYSDSPCLK_ENA_WIDTH 1 /* SYSDSPCLK_ENA */
-
-/*
- * R521 (0x209) - Clocking (2)
- */
-#define WM8915_TOCLK_DIV_MASK 0x0700 /* TOCLK_DIV - [10:8] */
-#define WM8915_TOCLK_DIV_SHIFT 8 /* TOCLK_DIV - [10:8] */
-#define WM8915_TOCLK_DIV_WIDTH 3 /* TOCLK_DIV - [10:8] */
-#define WM8915_DBCLK_DIV_MASK 0x00F0 /* DBCLK_DIV - [7:4] */
-#define WM8915_DBCLK_DIV_SHIFT 4 /* DBCLK_DIV - [7:4] */
-#define WM8915_DBCLK_DIV_WIDTH 4 /* DBCLK_DIV - [7:4] */
-#define WM8915_OPCLK_DIV_MASK 0x0007 /* OPCLK_DIV - [2:0] */
-#define WM8915_OPCLK_DIV_SHIFT 0 /* OPCLK_DIV - [2:0] */
-#define WM8915_OPCLK_DIV_WIDTH 3 /* OPCLK_DIV - [2:0] */
-
-/*
- * R528 (0x210) - AIF Rate
- */
-#define WM8915_SYSCLK_RATE 0x0001 /* SYSCLK_RATE */
-#define WM8915_SYSCLK_RATE_MASK 0x0001 /* SYSCLK_RATE */
-#define WM8915_SYSCLK_RATE_SHIFT 0 /* SYSCLK_RATE */
-#define WM8915_SYSCLK_RATE_WIDTH 1 /* SYSCLK_RATE */
-
-/*
- * R544 (0x220) - FLL Control (1)
- */
-#define WM8915_FLL_OSC_ENA 0x0002 /* FLL_OSC_ENA */
-#define WM8915_FLL_OSC_ENA_MASK 0x0002 /* FLL_OSC_ENA */
-#define WM8915_FLL_OSC_ENA_SHIFT 1 /* FLL_OSC_ENA */
-#define WM8915_FLL_OSC_ENA_WIDTH 1 /* FLL_OSC_ENA */
-#define WM8915_FLL_ENA 0x0001 /* FLL_ENA */
-#define WM8915_FLL_ENA_MASK 0x0001 /* FLL_ENA */
-#define WM8915_FLL_ENA_SHIFT 0 /* FLL_ENA */
-#define WM8915_FLL_ENA_WIDTH 1 /* FLL_ENA */
-
-/*
- * R545 (0x221) - FLL Control (2)
- */
-#define WM8915_FLL_OUTDIV_MASK 0x3F00 /* FLL_OUTDIV - [13:8] */
-#define WM8915_FLL_OUTDIV_SHIFT 8 /* FLL_OUTDIV - [13:8] */
-#define WM8915_FLL_OUTDIV_WIDTH 6 /* FLL_OUTDIV - [13:8] */
-#define WM8915_FLL_FRATIO_MASK 0x0007 /* FLL_FRATIO - [2:0] */
-#define WM8915_FLL_FRATIO_SHIFT 0 /* FLL_FRATIO - [2:0] */
-#define WM8915_FLL_FRATIO_WIDTH 3 /* FLL_FRATIO - [2:0] */
-
-/*
- * R546 (0x222) - FLL Control (3)
- */
-#define WM8915_FLL_THETA_MASK 0xFFFF /* FLL_THETA - [15:0] */
-#define WM8915_FLL_THETA_SHIFT 0 /* FLL_THETA - [15:0] */
-#define WM8915_FLL_THETA_WIDTH 16 /* FLL_THETA - [15:0] */
-
-/*
- * R547 (0x223) - FLL Control (4)
- */
-#define WM8915_FLL_N_MASK 0x7FE0 /* FLL_N - [14:5] */
-#define WM8915_FLL_N_SHIFT 5 /* FLL_N - [14:5] */
-#define WM8915_FLL_N_WIDTH 10 /* FLL_N - [14:5] */
-#define WM8915_FLL_LOOP_GAIN_MASK 0x000F /* FLL_LOOP_GAIN - [3:0] */
-#define WM8915_FLL_LOOP_GAIN_SHIFT 0 /* FLL_LOOP_GAIN - [3:0] */
-#define WM8915_FLL_LOOP_GAIN_WIDTH 4 /* FLL_LOOP_GAIN - [3:0] */
-
-/*
- * R548 (0x224) - FLL Control (5)
- */
-#define WM8915_FLL_FRC_NCO_VAL_MASK 0x1F80 /* FLL_FRC_NCO_VAL - [12:7] */
-#define WM8915_FLL_FRC_NCO_VAL_SHIFT 7 /* FLL_FRC_NCO_VAL - [12:7] */
-#define WM8915_FLL_FRC_NCO_VAL_WIDTH 6 /* FLL_FRC_NCO_VAL - [12:7] */
-#define WM8915_FLL_FRC_NCO 0x0040 /* FLL_FRC_NCO */
-#define WM8915_FLL_FRC_NCO_MASK 0x0040 /* FLL_FRC_NCO */
-#define WM8915_FLL_FRC_NCO_SHIFT 6 /* FLL_FRC_NCO */
-#define WM8915_FLL_FRC_NCO_WIDTH 1 /* FLL_FRC_NCO */
-#define WM8915_FLL_REFCLK_DIV_MASK 0x0018 /* FLL_REFCLK_DIV - [4:3] */
-#define WM8915_FLL_REFCLK_DIV_SHIFT 3 /* FLL_REFCLK_DIV - [4:3] */
-#define WM8915_FLL_REFCLK_DIV_WIDTH 2 /* FLL_REFCLK_DIV - [4:3] */
-#define WM8915_FLL_REF_FREQ 0x0004 /* FLL_REF_FREQ */
-#define WM8915_FLL_REF_FREQ_MASK 0x0004 /* FLL_REF_FREQ */
-#define WM8915_FLL_REF_FREQ_SHIFT 2 /* FLL_REF_FREQ */
-#define WM8915_FLL_REF_FREQ_WIDTH 1 /* FLL_REF_FREQ */
-#define WM8915_FLL_REFCLK_SRC_MASK 0x0003 /* FLL_REFCLK_SRC - [1:0] */
-#define WM8915_FLL_REFCLK_SRC_SHIFT 0 /* FLL_REFCLK_SRC - [1:0] */
-#define WM8915_FLL_REFCLK_SRC_WIDTH 2 /* FLL_REFCLK_SRC - [1:0] */
-
-/*
- * R549 (0x225) - FLL Control (6)
- */
-#define WM8915_FLL_REFCLK_SRC_STS_MASK 0x000C /* FLL_REFCLK_SRC_STS - [3:2] */
-#define WM8915_FLL_REFCLK_SRC_STS_SHIFT 2 /* FLL_REFCLK_SRC_STS - [3:2] */
-#define WM8915_FLL_REFCLK_SRC_STS_WIDTH 2 /* FLL_REFCLK_SRC_STS - [3:2] */
-#define WM8915_FLL_SWITCH_CLK 0x0001 /* FLL_SWITCH_CLK */
-#define WM8915_FLL_SWITCH_CLK_MASK 0x0001 /* FLL_SWITCH_CLK */
-#define WM8915_FLL_SWITCH_CLK_SHIFT 0 /* FLL_SWITCH_CLK */
-#define WM8915_FLL_SWITCH_CLK_WIDTH 1 /* FLL_SWITCH_CLK */
-
-/*
- * R550 (0x226) - FLL EFS 1
- */
-#define WM8915_FLL_LAMBDA_MASK 0xFFFF /* FLL_LAMBDA - [15:0] */
-#define WM8915_FLL_LAMBDA_SHIFT 0 /* FLL_LAMBDA - [15:0] */
-#define WM8915_FLL_LAMBDA_WIDTH 16 /* FLL_LAMBDA - [15:0] */
-
-/*
- * R551 (0x227) - FLL EFS 2
- */
-#define WM8915_FLL_LFSR_SEL_MASK 0x0006 /* FLL_LFSR_SEL - [2:1] */
-#define WM8915_FLL_LFSR_SEL_SHIFT 1 /* FLL_LFSR_SEL - [2:1] */
-#define WM8915_FLL_LFSR_SEL_WIDTH 2 /* FLL_LFSR_SEL - [2:1] */
-#define WM8915_FLL_EFS_ENA 0x0001 /* FLL_EFS_ENA */
-#define WM8915_FLL_EFS_ENA_MASK 0x0001 /* FLL_EFS_ENA */
-#define WM8915_FLL_EFS_ENA_SHIFT 0 /* FLL_EFS_ENA */
-#define WM8915_FLL_EFS_ENA_WIDTH 1 /* FLL_EFS_ENA */
-
-/*
- * R768 (0x300) - AIF1 Control
- */
-#define WM8915_AIF1_TRI 0x0004 /* AIF1_TRI */
-#define WM8915_AIF1_TRI_MASK 0x0004 /* AIF1_TRI */
-#define WM8915_AIF1_TRI_SHIFT 2 /* AIF1_TRI */
-#define WM8915_AIF1_TRI_WIDTH 1 /* AIF1_TRI */
-#define WM8915_AIF1_FMT_MASK 0x0003 /* AIF1_FMT - [1:0] */
-#define WM8915_AIF1_FMT_SHIFT 0 /* AIF1_FMT - [1:0] */
-#define WM8915_AIF1_FMT_WIDTH 2 /* AIF1_FMT - [1:0] */
-
-/*
- * R769 (0x301) - AIF1 BCLK
- */
-#define WM8915_AIF1_BCLK_INV 0x0400 /* AIF1_BCLK_INV */
-#define WM8915_AIF1_BCLK_INV_MASK 0x0400 /* AIF1_BCLK_INV */
-#define WM8915_AIF1_BCLK_INV_SHIFT 10 /* AIF1_BCLK_INV */
-#define WM8915_AIF1_BCLK_INV_WIDTH 1 /* AIF1_BCLK_INV */
-#define WM8915_AIF1_BCLK_FRC 0x0200 /* AIF1_BCLK_FRC */
-#define WM8915_AIF1_BCLK_FRC_MASK 0x0200 /* AIF1_BCLK_FRC */
-#define WM8915_AIF1_BCLK_FRC_SHIFT 9 /* AIF1_BCLK_FRC */
-#define WM8915_AIF1_BCLK_FRC_WIDTH 1 /* AIF1_BCLK_FRC */
-#define WM8915_AIF1_BCLK_MSTR 0x0100 /* AIF1_BCLK_MSTR */
-#define WM8915_AIF1_BCLK_MSTR_MASK 0x0100 /* AIF1_BCLK_MSTR */
-#define WM8915_AIF1_BCLK_MSTR_SHIFT 8 /* AIF1_BCLK_MSTR */
-#define WM8915_AIF1_BCLK_MSTR_WIDTH 1 /* AIF1_BCLK_MSTR */
-#define WM8915_AIF1_BCLK_DIV_MASK 0x000F /* AIF1_BCLK_DIV - [3:0] */
-#define WM8915_AIF1_BCLK_DIV_SHIFT 0 /* AIF1_BCLK_DIV - [3:0] */
-#define WM8915_AIF1_BCLK_DIV_WIDTH 4 /* AIF1_BCLK_DIV - [3:0] */
-
-/*
- * R770 (0x302) - AIF1 TX LRCLK(1)
- */
-#define WM8915_AIF1TX_RATE_MASK 0x07FF /* AIF1TX_RATE - [10:0] */
-#define WM8915_AIF1TX_RATE_SHIFT 0 /* AIF1TX_RATE - [10:0] */
-#define WM8915_AIF1TX_RATE_WIDTH 11 /* AIF1TX_RATE - [10:0] */
-
-/*
- * R771 (0x303) - AIF1 TX LRCLK(2)
- */
-#define WM8915_AIF1TX_LRCLK_MODE 0x0008 /* AIF1TX_LRCLK_MODE */
-#define WM8915_AIF1TX_LRCLK_MODE_MASK 0x0008 /* AIF1TX_LRCLK_MODE */
-#define WM8915_AIF1TX_LRCLK_MODE_SHIFT 3 /* AIF1TX_LRCLK_MODE */
-#define WM8915_AIF1TX_LRCLK_MODE_WIDTH 1 /* AIF1TX_LRCLK_MODE */
-#define WM8915_AIF1TX_LRCLK_INV 0x0004 /* AIF1TX_LRCLK_INV */
-#define WM8915_AIF1TX_LRCLK_INV_MASK 0x0004 /* AIF1TX_LRCLK_INV */
-#define WM8915_AIF1TX_LRCLK_INV_SHIFT 2 /* AIF1TX_LRCLK_INV */
-#define WM8915_AIF1TX_LRCLK_INV_WIDTH 1 /* AIF1TX_LRCLK_INV */
-#define WM8915_AIF1TX_LRCLK_FRC 0x0002 /* AIF1TX_LRCLK_FRC */
-#define WM8915_AIF1TX_LRCLK_FRC_MASK 0x0002 /* AIF1TX_LRCLK_FRC */
-#define WM8915_AIF1TX_LRCLK_FRC_SHIFT 1 /* AIF1TX_LRCLK_FRC */
-#define WM8915_AIF1TX_LRCLK_FRC_WIDTH 1 /* AIF1TX_LRCLK_FRC */
-#define WM8915_AIF1TX_LRCLK_MSTR 0x0001 /* AIF1TX_LRCLK_MSTR */
-#define WM8915_AIF1TX_LRCLK_MSTR_MASK 0x0001 /* AIF1TX_LRCLK_MSTR */
-#define WM8915_AIF1TX_LRCLK_MSTR_SHIFT 0 /* AIF1TX_LRCLK_MSTR */
-#define WM8915_AIF1TX_LRCLK_MSTR_WIDTH 1 /* AIF1TX_LRCLK_MSTR */
-
-/*
- * R772 (0x304) - AIF1 RX LRCLK(1)
- */
-#define WM8915_AIF1RX_RATE_MASK 0x07FF /* AIF1RX_RATE - [10:0] */
-#define WM8915_AIF1RX_RATE_SHIFT 0 /* AIF1RX_RATE - [10:0] */
-#define WM8915_AIF1RX_RATE_WIDTH 11 /* AIF1RX_RATE - [10:0] */
-
-/*
- * R773 (0x305) - AIF1 RX LRCLK(2)
- */
-#define WM8915_AIF1RX_LRCLK_INV 0x0004 /* AIF1RX_LRCLK_INV */
-#define WM8915_AIF1RX_LRCLK_INV_MASK 0x0004 /* AIF1RX_LRCLK_INV */
-#define WM8915_AIF1RX_LRCLK_INV_SHIFT 2 /* AIF1RX_LRCLK_INV */
-#define WM8915_AIF1RX_LRCLK_INV_WIDTH 1 /* AIF1RX_LRCLK_INV */
-#define WM8915_AIF1RX_LRCLK_FRC 0x0002 /* AIF1RX_LRCLK_FRC */
-#define WM8915_AIF1RX_LRCLK_FRC_MASK 0x0002 /* AIF1RX_LRCLK_FRC */
-#define WM8915_AIF1RX_LRCLK_FRC_SHIFT 1 /* AIF1RX_LRCLK_FRC */
-#define WM8915_AIF1RX_LRCLK_FRC_WIDTH 1 /* AIF1RX_LRCLK_FRC */
-#define WM8915_AIF1RX_LRCLK_MSTR 0x0001 /* AIF1RX_LRCLK_MSTR */
-#define WM8915_AIF1RX_LRCLK_MSTR_MASK 0x0001 /* AIF1RX_LRCLK_MSTR */
-#define WM8915_AIF1RX_LRCLK_MSTR_SHIFT 0 /* AIF1RX_LRCLK_MSTR */
-#define WM8915_AIF1RX_LRCLK_MSTR_WIDTH 1 /* AIF1RX_LRCLK_MSTR */
-
-/*
- * R774 (0x306) - AIF1TX Data Configuration (1)
- */
-#define WM8915_AIF1TX_WL_MASK 0xFF00 /* AIF1TX_WL - [15:8] */
-#define WM8915_AIF1TX_WL_SHIFT 8 /* AIF1TX_WL - [15:8] */
-#define WM8915_AIF1TX_WL_WIDTH 8 /* AIF1TX_WL - [15:8] */
-#define WM8915_AIF1TX_SLOT_LEN_MASK 0x00FF /* AIF1TX_SLOT_LEN - [7:0] */
-#define WM8915_AIF1TX_SLOT_LEN_SHIFT 0 /* AIF1TX_SLOT_LEN - [7:0] */
-#define WM8915_AIF1TX_SLOT_LEN_WIDTH 8 /* AIF1TX_SLOT_LEN - [7:0] */
-
-/*
- * R775 (0x307) - AIF1TX Data Configuration (2)
- */
-#define WM8915_AIF1TX_DAT_TRI 0x0001 /* AIF1TX_DAT_TRI */
-#define WM8915_AIF1TX_DAT_TRI_MASK 0x0001 /* AIF1TX_DAT_TRI */
-#define WM8915_AIF1TX_DAT_TRI_SHIFT 0 /* AIF1TX_DAT_TRI */
-#define WM8915_AIF1TX_DAT_TRI_WIDTH 1 /* AIF1TX_DAT_TRI */
-
-/*
- * R776 (0x308) - AIF1RX Data Configuration
- */
-#define WM8915_AIF1RX_WL_MASK 0xFF00 /* AIF1RX_WL - [15:8] */
-#define WM8915_AIF1RX_WL_SHIFT 8 /* AIF1RX_WL - [15:8] */
-#define WM8915_AIF1RX_WL_WIDTH 8 /* AIF1RX_WL - [15:8] */
-#define WM8915_AIF1RX_SLOT_LEN_MASK 0x00FF /* AIF1RX_SLOT_LEN - [7:0] */
-#define WM8915_AIF1RX_SLOT_LEN_SHIFT 0 /* AIF1RX_SLOT_LEN - [7:0] */
-#define WM8915_AIF1RX_SLOT_LEN_WIDTH 8 /* AIF1RX_SLOT_LEN - [7:0] */
-
-/*
- * R777 (0x309) - AIF1TX Channel 0 Configuration
- */
-#define WM8915_AIF1TX_CHAN0_DAT_INV 0x8000 /* AIF1TX_CHAN0_DAT_INV */
-#define WM8915_AIF1TX_CHAN0_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN0_DAT_INV */
-#define WM8915_AIF1TX_CHAN0_DAT_INV_SHIFT 15 /* AIF1TX_CHAN0_DAT_INV */
-#define WM8915_AIF1TX_CHAN0_DAT_INV_WIDTH 1 /* AIF1TX_CHAN0_DAT_INV */
-#define WM8915_AIF1TX_CHAN0_SPACING_MASK 0x7E00 /* AIF1TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN0_SPACING_SHIFT 9 /* AIF1TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN0_SPACING_WIDTH 6 /* AIF1TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN0_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN0_SLOTS_SHIFT 6 /* AIF1TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN0_SLOTS_WIDTH 3 /* AIF1TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN0_START_SLOT_MASK 0x003F /* AIF1TX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN0_START_SLOT_SHIFT 0 /* AIF1TX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN0_START_SLOT_WIDTH 6 /* AIF1TX_CHAN0_START_SLOT - [5:0] */
-
-/*
- * R778 (0x30A) - AIF1TX Channel 1 Configuration
- */
-#define WM8915_AIF1TX_CHAN1_DAT_INV 0x8000 /* AIF1TX_CHAN1_DAT_INV */
-#define WM8915_AIF1TX_CHAN1_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN1_DAT_INV */
-#define WM8915_AIF1TX_CHAN1_DAT_INV_SHIFT 15 /* AIF1TX_CHAN1_DAT_INV */
-#define WM8915_AIF1TX_CHAN1_DAT_INV_WIDTH 1 /* AIF1TX_CHAN1_DAT_INV */
-#define WM8915_AIF1TX_CHAN1_SPACING_MASK 0x7E00 /* AIF1TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN1_SPACING_SHIFT 9 /* AIF1TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN1_SPACING_WIDTH 6 /* AIF1TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN1_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN1_SLOTS_SHIFT 6 /* AIF1TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN1_SLOTS_WIDTH 3 /* AIF1TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN1_START_SLOT_MASK 0x003F /* AIF1TX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN1_START_SLOT_SHIFT 0 /* AIF1TX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN1_START_SLOT_WIDTH 6 /* AIF1TX_CHAN1_START_SLOT - [5:0] */
-
-/*
- * R779 (0x30B) - AIF1TX Channel 2 Configuration
- */
-#define WM8915_AIF1TX_CHAN2_DAT_INV 0x8000 /* AIF1TX_CHAN2_DAT_INV */
-#define WM8915_AIF1TX_CHAN2_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN2_DAT_INV */
-#define WM8915_AIF1TX_CHAN2_DAT_INV_SHIFT 15 /* AIF1TX_CHAN2_DAT_INV */
-#define WM8915_AIF1TX_CHAN2_DAT_INV_WIDTH 1 /* AIF1TX_CHAN2_DAT_INV */
-#define WM8915_AIF1TX_CHAN2_SPACING_MASK 0x7E00 /* AIF1TX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN2_SPACING_SHIFT 9 /* AIF1TX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN2_SPACING_WIDTH 6 /* AIF1TX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN2_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN2_SLOTS_SHIFT 6 /* AIF1TX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN2_SLOTS_WIDTH 3 /* AIF1TX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN2_START_SLOT_MASK 0x003F /* AIF1TX_CHAN2_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN2_START_SLOT_SHIFT 0 /* AIF1TX_CHAN2_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN2_START_SLOT_WIDTH 6 /* AIF1TX_CHAN2_START_SLOT - [5:0] */
-
-/*
- * R780 (0x30C) - AIF1TX Channel 3 Configuration
- */
-#define WM8915_AIF1TX_CHAN3_DAT_INV 0x8000 /* AIF1TX_CHAN3_DAT_INV */
-#define WM8915_AIF1TX_CHAN3_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN3_DAT_INV */
-#define WM8915_AIF1TX_CHAN3_DAT_INV_SHIFT 15 /* AIF1TX_CHAN3_DAT_INV */
-#define WM8915_AIF1TX_CHAN3_DAT_INV_WIDTH 1 /* AIF1TX_CHAN3_DAT_INV */
-#define WM8915_AIF1TX_CHAN3_SPACING_MASK 0x7E00 /* AIF1TX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN3_SPACING_SHIFT 9 /* AIF1TX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN3_SPACING_WIDTH 6 /* AIF1TX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN3_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN3_SLOTS_SHIFT 6 /* AIF1TX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN3_SLOTS_WIDTH 3 /* AIF1TX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN3_START_SLOT_MASK 0x003F /* AIF1TX_CHAN3_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN3_START_SLOT_SHIFT 0 /* AIF1TX_CHAN3_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN3_START_SLOT_WIDTH 6 /* AIF1TX_CHAN3_START_SLOT - [5:0] */
-
-/*
- * R781 (0x30D) - AIF1TX Channel 4 Configuration
- */
-#define WM8915_AIF1TX_CHAN4_DAT_INV 0x8000 /* AIF1TX_CHAN4_DAT_INV */
-#define WM8915_AIF1TX_CHAN4_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN4_DAT_INV */
-#define WM8915_AIF1TX_CHAN4_DAT_INV_SHIFT 15 /* AIF1TX_CHAN4_DAT_INV */
-#define WM8915_AIF1TX_CHAN4_DAT_INV_WIDTH 1 /* AIF1TX_CHAN4_DAT_INV */
-#define WM8915_AIF1TX_CHAN4_SPACING_MASK 0x7E00 /* AIF1TX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN4_SPACING_SHIFT 9 /* AIF1TX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN4_SPACING_WIDTH 6 /* AIF1TX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN4_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN4_SLOTS_SHIFT 6 /* AIF1TX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN4_SLOTS_WIDTH 3 /* AIF1TX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN4_START_SLOT_MASK 0x003F /* AIF1TX_CHAN4_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN4_START_SLOT_SHIFT 0 /* AIF1TX_CHAN4_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN4_START_SLOT_WIDTH 6 /* AIF1TX_CHAN4_START_SLOT - [5:0] */
-
-/*
- * R782 (0x30E) - AIF1TX Channel 5 Configuration
- */
-#define WM8915_AIF1TX_CHAN5_DAT_INV 0x8000 /* AIF1TX_CHAN5_DAT_INV */
-#define WM8915_AIF1TX_CHAN5_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN5_DAT_INV */
-#define WM8915_AIF1TX_CHAN5_DAT_INV_SHIFT 15 /* AIF1TX_CHAN5_DAT_INV */
-#define WM8915_AIF1TX_CHAN5_DAT_INV_WIDTH 1 /* AIF1TX_CHAN5_DAT_INV */
-#define WM8915_AIF1TX_CHAN5_SPACING_MASK 0x7E00 /* AIF1TX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN5_SPACING_SHIFT 9 /* AIF1TX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN5_SPACING_WIDTH 6 /* AIF1TX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1TX_CHAN5_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN5_SLOTS_SHIFT 6 /* AIF1TX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN5_SLOTS_WIDTH 3 /* AIF1TX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1TX_CHAN5_START_SLOT_MASK 0x003F /* AIF1TX_CHAN5_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN5_START_SLOT_SHIFT 0 /* AIF1TX_CHAN5_START_SLOT - [5:0] */
-#define WM8915_AIF1TX_CHAN5_START_SLOT_WIDTH 6 /* AIF1TX_CHAN5_START_SLOT - [5:0] */
-
-/*
- * R783 (0x30F) - AIF1RX Channel 0 Configuration
- */
-#define WM8915_AIF1RX_CHAN0_DAT_INV 0x8000 /* AIF1RX_CHAN0_DAT_INV */
-#define WM8915_AIF1RX_CHAN0_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN0_DAT_INV */
-#define WM8915_AIF1RX_CHAN0_DAT_INV_SHIFT 15 /* AIF1RX_CHAN0_DAT_INV */
-#define WM8915_AIF1RX_CHAN0_DAT_INV_WIDTH 1 /* AIF1RX_CHAN0_DAT_INV */
-#define WM8915_AIF1RX_CHAN0_SPACING_MASK 0x7E00 /* AIF1RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN0_SPACING_SHIFT 9 /* AIF1RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN0_SPACING_WIDTH 6 /* AIF1RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN0_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN0_SLOTS_SHIFT 6 /* AIF1RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN0_SLOTS_WIDTH 3 /* AIF1RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN0_START_SLOT_MASK 0x003F /* AIF1RX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN0_START_SLOT_SHIFT 0 /* AIF1RX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN0_START_SLOT_WIDTH 6 /* AIF1RX_CHAN0_START_SLOT - [5:0] */
-
-/*
- * R784 (0x310) - AIF1RX Channel 1 Configuration
- */
-#define WM8915_AIF1RX_CHAN1_DAT_INV 0x8000 /* AIF1RX_CHAN1_DAT_INV */
-#define WM8915_AIF1RX_CHAN1_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN1_DAT_INV */
-#define WM8915_AIF1RX_CHAN1_DAT_INV_SHIFT 15 /* AIF1RX_CHAN1_DAT_INV */
-#define WM8915_AIF1RX_CHAN1_DAT_INV_WIDTH 1 /* AIF1RX_CHAN1_DAT_INV */
-#define WM8915_AIF1RX_CHAN1_SPACING_MASK 0x7E00 /* AIF1RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN1_SPACING_SHIFT 9 /* AIF1RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN1_SPACING_WIDTH 6 /* AIF1RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN1_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN1_SLOTS_SHIFT 6 /* AIF1RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN1_SLOTS_WIDTH 3 /* AIF1RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN1_START_SLOT_MASK 0x003F /* AIF1RX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN1_START_SLOT_SHIFT 0 /* AIF1RX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN1_START_SLOT_WIDTH 6 /* AIF1RX_CHAN1_START_SLOT - [5:0] */
-
-/*
- * R785 (0x311) - AIF1RX Channel 2 Configuration
- */
-#define WM8915_AIF1RX_CHAN2_DAT_INV 0x8000 /* AIF1RX_CHAN2_DAT_INV */
-#define WM8915_AIF1RX_CHAN2_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN2_DAT_INV */
-#define WM8915_AIF1RX_CHAN2_DAT_INV_SHIFT 15 /* AIF1RX_CHAN2_DAT_INV */
-#define WM8915_AIF1RX_CHAN2_DAT_INV_WIDTH 1 /* AIF1RX_CHAN2_DAT_INV */
-#define WM8915_AIF1RX_CHAN2_SPACING_MASK 0x7E00 /* AIF1RX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN2_SPACING_SHIFT 9 /* AIF1RX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN2_SPACING_WIDTH 6 /* AIF1RX_CHAN2_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN2_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN2_SLOTS_SHIFT 6 /* AIF1RX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN2_SLOTS_WIDTH 3 /* AIF1RX_CHAN2_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN2_START_SLOT_MASK 0x003F /* AIF1RX_CHAN2_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN2_START_SLOT_SHIFT 0 /* AIF1RX_CHAN2_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN2_START_SLOT_WIDTH 6 /* AIF1RX_CHAN2_START_SLOT - [5:0] */
-
-/*
- * R786 (0x312) - AIF1RX Channel 3 Configuration
- */
-#define WM8915_AIF1RX_CHAN3_DAT_INV 0x8000 /* AIF1RX_CHAN3_DAT_INV */
-#define WM8915_AIF1RX_CHAN3_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN3_DAT_INV */
-#define WM8915_AIF1RX_CHAN3_DAT_INV_SHIFT 15 /* AIF1RX_CHAN3_DAT_INV */
-#define WM8915_AIF1RX_CHAN3_DAT_INV_WIDTH 1 /* AIF1RX_CHAN3_DAT_INV */
-#define WM8915_AIF1RX_CHAN3_SPACING_MASK 0x7E00 /* AIF1RX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN3_SPACING_SHIFT 9 /* AIF1RX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN3_SPACING_WIDTH 6 /* AIF1RX_CHAN3_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN3_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN3_SLOTS_SHIFT 6 /* AIF1RX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN3_SLOTS_WIDTH 3 /* AIF1RX_CHAN3_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN3_START_SLOT_MASK 0x003F /* AIF1RX_CHAN3_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN3_START_SLOT_SHIFT 0 /* AIF1RX_CHAN3_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN3_START_SLOT_WIDTH 6 /* AIF1RX_CHAN3_START_SLOT - [5:0] */
-
-/*
- * R787 (0x313) - AIF1RX Channel 4 Configuration
- */
-#define WM8915_AIF1RX_CHAN4_DAT_INV 0x8000 /* AIF1RX_CHAN4_DAT_INV */
-#define WM8915_AIF1RX_CHAN4_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN4_DAT_INV */
-#define WM8915_AIF1RX_CHAN4_DAT_INV_SHIFT 15 /* AIF1RX_CHAN4_DAT_INV */
-#define WM8915_AIF1RX_CHAN4_DAT_INV_WIDTH 1 /* AIF1RX_CHAN4_DAT_INV */
-#define WM8915_AIF1RX_CHAN4_SPACING_MASK 0x7E00 /* AIF1RX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN4_SPACING_SHIFT 9 /* AIF1RX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN4_SPACING_WIDTH 6 /* AIF1RX_CHAN4_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN4_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN4_SLOTS_SHIFT 6 /* AIF1RX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN4_SLOTS_WIDTH 3 /* AIF1RX_CHAN4_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN4_START_SLOT_MASK 0x003F /* AIF1RX_CHAN4_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN4_START_SLOT_SHIFT 0 /* AIF1RX_CHAN4_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN4_START_SLOT_WIDTH 6 /* AIF1RX_CHAN4_START_SLOT - [5:0] */
-
-/*
- * R788 (0x314) - AIF1RX Channel 5 Configuration
- */
-#define WM8915_AIF1RX_CHAN5_DAT_INV 0x8000 /* AIF1RX_CHAN5_DAT_INV */
-#define WM8915_AIF1RX_CHAN5_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN5_DAT_INV */
-#define WM8915_AIF1RX_CHAN5_DAT_INV_SHIFT 15 /* AIF1RX_CHAN5_DAT_INV */
-#define WM8915_AIF1RX_CHAN5_DAT_INV_WIDTH 1 /* AIF1RX_CHAN5_DAT_INV */
-#define WM8915_AIF1RX_CHAN5_SPACING_MASK 0x7E00 /* AIF1RX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN5_SPACING_SHIFT 9 /* AIF1RX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN5_SPACING_WIDTH 6 /* AIF1RX_CHAN5_SPACING - [14:9] */
-#define WM8915_AIF1RX_CHAN5_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN5_SLOTS_SHIFT 6 /* AIF1RX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN5_SLOTS_WIDTH 3 /* AIF1RX_CHAN5_SLOTS - [8:6] */
-#define WM8915_AIF1RX_CHAN5_START_SLOT_MASK 0x003F /* AIF1RX_CHAN5_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN5_START_SLOT_SHIFT 0 /* AIF1RX_CHAN5_START_SLOT - [5:0] */
-#define WM8915_AIF1RX_CHAN5_START_SLOT_WIDTH 6 /* AIF1RX_CHAN5_START_SLOT - [5:0] */
-
-/*
- * R789 (0x315) - AIF1RX Mono Configuration
- */
-#define WM8915_AIF1RX_CHAN4_MONO_MODE 0x0004 /* AIF1RX_CHAN4_MONO_MODE */
-#define WM8915_AIF1RX_CHAN4_MONO_MODE_MASK 0x0004 /* AIF1RX_CHAN4_MONO_MODE */
-#define WM8915_AIF1RX_CHAN4_MONO_MODE_SHIFT 2 /* AIF1RX_CHAN4_MONO_MODE */
-#define WM8915_AIF1RX_CHAN4_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN4_MONO_MODE */
-#define WM8915_AIF1RX_CHAN2_MONO_MODE 0x0002 /* AIF1RX_CHAN2_MONO_MODE */
-#define WM8915_AIF1RX_CHAN2_MONO_MODE_MASK 0x0002 /* AIF1RX_CHAN2_MONO_MODE */
-#define WM8915_AIF1RX_CHAN2_MONO_MODE_SHIFT 1 /* AIF1RX_CHAN2_MONO_MODE */
-#define WM8915_AIF1RX_CHAN2_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN2_MONO_MODE */
-#define WM8915_AIF1RX_CHAN0_MONO_MODE 0x0001 /* AIF1RX_CHAN0_MONO_MODE */
-#define WM8915_AIF1RX_CHAN0_MONO_MODE_MASK 0x0001 /* AIF1RX_CHAN0_MONO_MODE */
-#define WM8915_AIF1RX_CHAN0_MONO_MODE_SHIFT 0 /* AIF1RX_CHAN0_MONO_MODE */
-#define WM8915_AIF1RX_CHAN0_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN0_MONO_MODE */
-
-/*
- * R794 (0x31A) - AIF1TX Test
- */
-#define WM8915_AIF1TX45_DITHER_ENA 0x0004 /* AIF1TX45_DITHER_ENA */
-#define WM8915_AIF1TX45_DITHER_ENA_MASK 0x0004 /* AIF1TX45_DITHER_ENA */
-#define WM8915_AIF1TX45_DITHER_ENA_SHIFT 2 /* AIF1TX45_DITHER_ENA */
-#define WM8915_AIF1TX45_DITHER_ENA_WIDTH 1 /* AIF1TX45_DITHER_ENA */
-#define WM8915_AIF1TX23_DITHER_ENA 0x0002 /* AIF1TX23_DITHER_ENA */
-#define WM8915_AIF1TX23_DITHER_ENA_MASK 0x0002 /* AIF1TX23_DITHER_ENA */
-#define WM8915_AIF1TX23_DITHER_ENA_SHIFT 1 /* AIF1TX23_DITHER_ENA */
-#define WM8915_AIF1TX23_DITHER_ENA_WIDTH 1 /* AIF1TX23_DITHER_ENA */
-#define WM8915_AIF1TX01_DITHER_ENA 0x0001 /* AIF1TX01_DITHER_ENA */
-#define WM8915_AIF1TX01_DITHER_ENA_MASK 0x0001 /* AIF1TX01_DITHER_ENA */
-#define WM8915_AIF1TX01_DITHER_ENA_SHIFT 0 /* AIF1TX01_DITHER_ENA */
-#define WM8915_AIF1TX01_DITHER_ENA_WIDTH 1 /* AIF1TX01_DITHER_ENA */
-
-/*
- * R800 (0x320) - AIF2 Control
- */
-#define WM8915_AIF2_TRI 0x0004 /* AIF2_TRI */
-#define WM8915_AIF2_TRI_MASK 0x0004 /* AIF2_TRI */
-#define WM8915_AIF2_TRI_SHIFT 2 /* AIF2_TRI */
-#define WM8915_AIF2_TRI_WIDTH 1 /* AIF2_TRI */
-#define WM8915_AIF2_FMT_MASK 0x0003 /* AIF2_FMT - [1:0] */
-#define WM8915_AIF2_FMT_SHIFT 0 /* AIF2_FMT - [1:0] */
-#define WM8915_AIF2_FMT_WIDTH 2 /* AIF2_FMT - [1:0] */
-
-/*
- * R801 (0x321) - AIF2 BCLK
- */
-#define WM8915_AIF2_BCLK_INV 0x0400 /* AIF2_BCLK_INV */
-#define WM8915_AIF2_BCLK_INV_MASK 0x0400 /* AIF2_BCLK_INV */
-#define WM8915_AIF2_BCLK_INV_SHIFT 10 /* AIF2_BCLK_INV */
-#define WM8915_AIF2_BCLK_INV_WIDTH 1 /* AIF2_BCLK_INV */
-#define WM8915_AIF2_BCLK_FRC 0x0200 /* AIF2_BCLK_FRC */
-#define WM8915_AIF2_BCLK_FRC_MASK 0x0200 /* AIF2_BCLK_FRC */
-#define WM8915_AIF2_BCLK_FRC_SHIFT 9 /* AIF2_BCLK_FRC */
-#define WM8915_AIF2_BCLK_FRC_WIDTH 1 /* AIF2_BCLK_FRC */
-#define WM8915_AIF2_BCLK_MSTR 0x0100 /* AIF2_BCLK_MSTR */
-#define WM8915_AIF2_BCLK_MSTR_MASK 0x0100 /* AIF2_BCLK_MSTR */
-#define WM8915_AIF2_BCLK_MSTR_SHIFT 8 /* AIF2_BCLK_MSTR */
-#define WM8915_AIF2_BCLK_MSTR_WIDTH 1 /* AIF2_BCLK_MSTR */
-#define WM8915_AIF2_BCLK_DIV_MASK 0x000F /* AIF2_BCLK_DIV - [3:0] */
-#define WM8915_AIF2_BCLK_DIV_SHIFT 0 /* AIF2_BCLK_DIV - [3:0] */
-#define WM8915_AIF2_BCLK_DIV_WIDTH 4 /* AIF2_BCLK_DIV - [3:0] */
-
-/*
- * R802 (0x322) - AIF2 TX LRCLK(1)
- */
-#define WM8915_AIF2TX_RATE_MASK 0x07FF /* AIF2TX_RATE - [10:0] */
-#define WM8915_AIF2TX_RATE_SHIFT 0 /* AIF2TX_RATE - [10:0] */
-#define WM8915_AIF2TX_RATE_WIDTH 11 /* AIF2TX_RATE - [10:0] */
-
-/*
- * R803 (0x323) - AIF2 TX LRCLK(2)
- */
-#define WM8915_AIF2TX_LRCLK_MODE 0x0008 /* AIF2TX_LRCLK_MODE */
-#define WM8915_AIF2TX_LRCLK_MODE_MASK 0x0008 /* AIF2TX_LRCLK_MODE */
-#define WM8915_AIF2TX_LRCLK_MODE_SHIFT 3 /* AIF2TX_LRCLK_MODE */
-#define WM8915_AIF2TX_LRCLK_MODE_WIDTH 1 /* AIF2TX_LRCLK_MODE */
-#define WM8915_AIF2TX_LRCLK_INV 0x0004 /* AIF2TX_LRCLK_INV */
-#define WM8915_AIF2TX_LRCLK_INV_MASK 0x0004 /* AIF2TX_LRCLK_INV */
-#define WM8915_AIF2TX_LRCLK_INV_SHIFT 2 /* AIF2TX_LRCLK_INV */
-#define WM8915_AIF2TX_LRCLK_INV_WIDTH 1 /* AIF2TX_LRCLK_INV */
-#define WM8915_AIF2TX_LRCLK_FRC 0x0002 /* AIF2TX_LRCLK_FRC */
-#define WM8915_AIF2TX_LRCLK_FRC_MASK 0x0002 /* AIF2TX_LRCLK_FRC */
-#define WM8915_AIF2TX_LRCLK_FRC_SHIFT 1 /* AIF2TX_LRCLK_FRC */
-#define WM8915_AIF2TX_LRCLK_FRC_WIDTH 1 /* AIF2TX_LRCLK_FRC */
-#define WM8915_AIF2TX_LRCLK_MSTR 0x0001 /* AIF2TX_LRCLK_MSTR */
-#define WM8915_AIF2TX_LRCLK_MSTR_MASK 0x0001 /* AIF2TX_LRCLK_MSTR */
-#define WM8915_AIF2TX_LRCLK_MSTR_SHIFT 0 /* AIF2TX_LRCLK_MSTR */
-#define WM8915_AIF2TX_LRCLK_MSTR_WIDTH 1 /* AIF2TX_LRCLK_MSTR */
-
-/*
- * R804 (0x324) - AIF2 RX LRCLK(1)
- */
-#define WM8915_AIF2RX_RATE_MASK 0x07FF /* AIF2RX_RATE - [10:0] */
-#define WM8915_AIF2RX_RATE_SHIFT 0 /* AIF2RX_RATE - [10:0] */
-#define WM8915_AIF2RX_RATE_WIDTH 11 /* AIF2RX_RATE - [10:0] */
-
-/*
- * R805 (0x325) - AIF2 RX LRCLK(2)
- */
-#define WM8915_AIF2RX_LRCLK_INV 0x0004 /* AIF2RX_LRCLK_INV */
-#define WM8915_AIF2RX_LRCLK_INV_MASK 0x0004 /* AIF2RX_LRCLK_INV */
-#define WM8915_AIF2RX_LRCLK_INV_SHIFT 2 /* AIF2RX_LRCLK_INV */
-#define WM8915_AIF2RX_LRCLK_INV_WIDTH 1 /* AIF2RX_LRCLK_INV */
-#define WM8915_AIF2RX_LRCLK_FRC 0x0002 /* AIF2RX_LRCLK_FRC */
-#define WM8915_AIF2RX_LRCLK_FRC_MASK 0x0002 /* AIF2RX_LRCLK_FRC */
-#define WM8915_AIF2RX_LRCLK_FRC_SHIFT 1 /* AIF2RX_LRCLK_FRC */
-#define WM8915_AIF2RX_LRCLK_FRC_WIDTH 1 /* AIF2RX_LRCLK_FRC */
-#define WM8915_AIF2RX_LRCLK_MSTR 0x0001 /* AIF2RX_LRCLK_MSTR */
-#define WM8915_AIF2RX_LRCLK_MSTR_MASK 0x0001 /* AIF2RX_LRCLK_MSTR */
-#define WM8915_AIF2RX_LRCLK_MSTR_SHIFT 0 /* AIF2RX_LRCLK_MSTR */
-#define WM8915_AIF2RX_LRCLK_MSTR_WIDTH 1 /* AIF2RX_LRCLK_MSTR */
-
-/*
- * R806 (0x326) - AIF2TX Data Configuration (1)
- */
-#define WM8915_AIF2TX_WL_MASK 0xFF00 /* AIF2TX_WL - [15:8] */
-#define WM8915_AIF2TX_WL_SHIFT 8 /* AIF2TX_WL - [15:8] */
-#define WM8915_AIF2TX_WL_WIDTH 8 /* AIF2TX_WL - [15:8] */
-#define WM8915_AIF2TX_SLOT_LEN_MASK 0x00FF /* AIF2TX_SLOT_LEN - [7:0] */
-#define WM8915_AIF2TX_SLOT_LEN_SHIFT 0 /* AIF2TX_SLOT_LEN - [7:0] */
-#define WM8915_AIF2TX_SLOT_LEN_WIDTH 8 /* AIF2TX_SLOT_LEN - [7:0] */
-
-/*
- * R807 (0x327) - AIF2TX Data Configuration (2)
- */
-#define WM8915_AIF2TX_DAT_TRI 0x0001 /* AIF2TX_DAT_TRI */
-#define WM8915_AIF2TX_DAT_TRI_MASK 0x0001 /* AIF2TX_DAT_TRI */
-#define WM8915_AIF2TX_DAT_TRI_SHIFT 0 /* AIF2TX_DAT_TRI */
-#define WM8915_AIF2TX_DAT_TRI_WIDTH 1 /* AIF2TX_DAT_TRI */
-
-/*
- * R808 (0x328) - AIF2RX Data Configuration
- */
-#define WM8915_AIF2RX_WL_MASK 0xFF00 /* AIF2RX_WL - [15:8] */
-#define WM8915_AIF2RX_WL_SHIFT 8 /* AIF2RX_WL - [15:8] */
-#define WM8915_AIF2RX_WL_WIDTH 8 /* AIF2RX_WL - [15:8] */
-#define WM8915_AIF2RX_SLOT_LEN_MASK 0x00FF /* AIF2RX_SLOT_LEN - [7:0] */
-#define WM8915_AIF2RX_SLOT_LEN_SHIFT 0 /* AIF2RX_SLOT_LEN - [7:0] */
-#define WM8915_AIF2RX_SLOT_LEN_WIDTH 8 /* AIF2RX_SLOT_LEN - [7:0] */
-
-/*
- * R809 (0x329) - AIF2TX Channel 0 Configuration
- */
-#define WM8915_AIF2TX_CHAN0_DAT_INV 0x8000 /* AIF2TX_CHAN0_DAT_INV */
-#define WM8915_AIF2TX_CHAN0_DAT_INV_MASK 0x8000 /* AIF2TX_CHAN0_DAT_INV */
-#define WM8915_AIF2TX_CHAN0_DAT_INV_SHIFT 15 /* AIF2TX_CHAN0_DAT_INV */
-#define WM8915_AIF2TX_CHAN0_DAT_INV_WIDTH 1 /* AIF2TX_CHAN0_DAT_INV */
-#define WM8915_AIF2TX_CHAN0_SPACING_MASK 0x7E00 /* AIF2TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN0_SPACING_SHIFT 9 /* AIF2TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN0_SPACING_WIDTH 6 /* AIF2TX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN0_SLOTS_MASK 0x01C0 /* AIF2TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN0_SLOTS_SHIFT 6 /* AIF2TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN0_SLOTS_WIDTH 3 /* AIF2TX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN0_START_SLOT_MASK 0x003F /* AIF2TX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF2TX_CHAN0_START_SLOT_SHIFT 0 /* AIF2TX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF2TX_CHAN0_START_SLOT_WIDTH 6 /* AIF2TX_CHAN0_START_SLOT - [5:0] */
-
-/*
- * R810 (0x32A) - AIF2TX Channel 1 Configuration
- */
-#define WM8915_AIF2TX_CHAN1_DAT_INV 0x8000 /* AIF2TX_CHAN1_DAT_INV */
-#define WM8915_AIF2TX_CHAN1_DAT_INV_MASK 0x8000 /* AIF2TX_CHAN1_DAT_INV */
-#define WM8915_AIF2TX_CHAN1_DAT_INV_SHIFT 15 /* AIF2TX_CHAN1_DAT_INV */
-#define WM8915_AIF2TX_CHAN1_DAT_INV_WIDTH 1 /* AIF2TX_CHAN1_DAT_INV */
-#define WM8915_AIF2TX_CHAN1_SPACING_MASK 0x7E00 /* AIF2TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN1_SPACING_SHIFT 9 /* AIF2TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN1_SPACING_WIDTH 6 /* AIF2TX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2TX_CHAN1_SLOTS_MASK 0x01C0 /* AIF2TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN1_SLOTS_SHIFT 6 /* AIF2TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN1_SLOTS_WIDTH 3 /* AIF2TX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2TX_CHAN1_START_SLOT_MASK 0x003F /* AIF2TX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF2TX_CHAN1_START_SLOT_SHIFT 0 /* AIF2TX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF2TX_CHAN1_START_SLOT_WIDTH 6 /* AIF2TX_CHAN1_START_SLOT - [5:0] */
-
-/*
- * R811 (0x32B) - AIF2RX Channel 0 Configuration
- */
-#define WM8915_AIF2RX_CHAN0_DAT_INV 0x8000 /* AIF2RX_CHAN0_DAT_INV */
-#define WM8915_AIF2RX_CHAN0_DAT_INV_MASK 0x8000 /* AIF2RX_CHAN0_DAT_INV */
-#define WM8915_AIF2RX_CHAN0_DAT_INV_SHIFT 15 /* AIF2RX_CHAN0_DAT_INV */
-#define WM8915_AIF2RX_CHAN0_DAT_INV_WIDTH 1 /* AIF2RX_CHAN0_DAT_INV */
-#define WM8915_AIF2RX_CHAN0_SPACING_MASK 0x7E00 /* AIF2RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN0_SPACING_SHIFT 9 /* AIF2RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN0_SPACING_WIDTH 6 /* AIF2RX_CHAN0_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN0_SLOTS_MASK 0x01C0 /* AIF2RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN0_SLOTS_SHIFT 6 /* AIF2RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN0_SLOTS_WIDTH 3 /* AIF2RX_CHAN0_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN0_START_SLOT_MASK 0x003F /* AIF2RX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF2RX_CHAN0_START_SLOT_SHIFT 0 /* AIF2RX_CHAN0_START_SLOT - [5:0] */
-#define WM8915_AIF2RX_CHAN0_START_SLOT_WIDTH 6 /* AIF2RX_CHAN0_START_SLOT - [5:0] */
-
-/*
- * R812 (0x32C) - AIF2RX Channel 1 Configuration
- */
-#define WM8915_AIF2RX_CHAN1_DAT_INV 0x8000 /* AIF2RX_CHAN1_DAT_INV */
-#define WM8915_AIF2RX_CHAN1_DAT_INV_MASK 0x8000 /* AIF2RX_CHAN1_DAT_INV */
-#define WM8915_AIF2RX_CHAN1_DAT_INV_SHIFT 15 /* AIF2RX_CHAN1_DAT_INV */
-#define WM8915_AIF2RX_CHAN1_DAT_INV_WIDTH 1 /* AIF2RX_CHAN1_DAT_INV */
-#define WM8915_AIF2RX_CHAN1_SPACING_MASK 0x7E00 /* AIF2RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN1_SPACING_SHIFT 9 /* AIF2RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN1_SPACING_WIDTH 6 /* AIF2RX_CHAN1_SPACING - [14:9] */
-#define WM8915_AIF2RX_CHAN1_SLOTS_MASK 0x01C0 /* AIF2RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN1_SLOTS_SHIFT 6 /* AIF2RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN1_SLOTS_WIDTH 3 /* AIF2RX_CHAN1_SLOTS - [8:6] */
-#define WM8915_AIF2RX_CHAN1_START_SLOT_MASK 0x003F /* AIF2RX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF2RX_CHAN1_START_SLOT_SHIFT 0 /* AIF2RX_CHAN1_START_SLOT - [5:0] */
-#define WM8915_AIF2RX_CHAN1_START_SLOT_WIDTH 6 /* AIF2RX_CHAN1_START_SLOT - [5:0] */
-
-/*
- * R813 (0x32D) - AIF2RX Mono Configuration
- */
-#define WM8915_AIF2RX_CHAN0_MONO_MODE 0x0001 /* AIF2RX_CHAN0_MONO_MODE */
-#define WM8915_AIF2RX_CHAN0_MONO_MODE_MASK 0x0001 /* AIF2RX_CHAN0_MONO_MODE */
-#define WM8915_AIF2RX_CHAN0_MONO_MODE_SHIFT 0 /* AIF2RX_CHAN0_MONO_MODE */
-#define WM8915_AIF2RX_CHAN0_MONO_MODE_WIDTH 1 /* AIF2RX_CHAN0_MONO_MODE */
-
-/*
- * R815 (0x32F) - AIF2TX Test
- */
-#define WM8915_AIF2TX_DITHER_ENA 0x0001 /* AIF2TX_DITHER_ENA */
-#define WM8915_AIF2TX_DITHER_ENA_MASK 0x0001 /* AIF2TX_DITHER_ENA */
-#define WM8915_AIF2TX_DITHER_ENA_SHIFT 0 /* AIF2TX_DITHER_ENA */
-#define WM8915_AIF2TX_DITHER_ENA_WIDTH 1 /* AIF2TX_DITHER_ENA */
-
-/*
- * R1024 (0x400) - DSP1 TX Left Volume
- */
-#define WM8915_DSP1TX_VU 0x0100 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_MASK 0x0100 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_SHIFT 8 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_WIDTH 1 /* DSP1TX_VU */
-#define WM8915_DSP1TXL_VOL_MASK 0x00FF /* DSP1TXL_VOL - [7:0] */
-#define WM8915_DSP1TXL_VOL_SHIFT 0 /* DSP1TXL_VOL - [7:0] */
-#define WM8915_DSP1TXL_VOL_WIDTH 8 /* DSP1TXL_VOL - [7:0] */
-
-/*
- * R1025 (0x401) - DSP1 TX Right Volume
- */
-#define WM8915_DSP1TX_VU 0x0100 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_MASK 0x0100 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_SHIFT 8 /* DSP1TX_VU */
-#define WM8915_DSP1TX_VU_WIDTH 1 /* DSP1TX_VU */
-#define WM8915_DSP1TXR_VOL_MASK 0x00FF /* DSP1TXR_VOL - [7:0] */
-#define WM8915_DSP1TXR_VOL_SHIFT 0 /* DSP1TXR_VOL - [7:0] */
-#define WM8915_DSP1TXR_VOL_WIDTH 8 /* DSP1TXR_VOL - [7:0] */
-
-/*
- * R1026 (0x402) - DSP1 RX Left Volume
- */
-#define WM8915_DSP1RX_VU 0x0100 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_MASK 0x0100 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_SHIFT 8 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_WIDTH 1 /* DSP1RX_VU */
-#define WM8915_DSP1RXL_VOL_MASK 0x00FF /* DSP1RXL_VOL - [7:0] */
-#define WM8915_DSP1RXL_VOL_SHIFT 0 /* DSP1RXL_VOL - [7:0] */
-#define WM8915_DSP1RXL_VOL_WIDTH 8 /* DSP1RXL_VOL - [7:0] */
-
-/*
- * R1027 (0x403) - DSP1 RX Right Volume
- */
-#define WM8915_DSP1RX_VU 0x0100 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_MASK 0x0100 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_SHIFT 8 /* DSP1RX_VU */
-#define WM8915_DSP1RX_VU_WIDTH 1 /* DSP1RX_VU */
-#define WM8915_DSP1RXR_VOL_MASK 0x00FF /* DSP1RXR_VOL - [7:0] */
-#define WM8915_DSP1RXR_VOL_SHIFT 0 /* DSP1RXR_VOL - [7:0] */
-#define WM8915_DSP1RXR_VOL_WIDTH 8 /* DSP1RXR_VOL - [7:0] */
-
-/*
- * R1040 (0x410) - DSP1 TX Filters
- */
-#define WM8915_DSP1TX_NF 0x2000 /* DSP1TX_NF */
-#define WM8915_DSP1TX_NF_MASK 0x2000 /* DSP1TX_NF */
-#define WM8915_DSP1TX_NF_SHIFT 13 /* DSP1TX_NF */
-#define WM8915_DSP1TX_NF_WIDTH 1 /* DSP1TX_NF */
-#define WM8915_DSP1TXL_HPF 0x1000 /* DSP1TXL_HPF */
-#define WM8915_DSP1TXL_HPF_MASK 0x1000 /* DSP1TXL_HPF */
-#define WM8915_DSP1TXL_HPF_SHIFT 12 /* DSP1TXL_HPF */
-#define WM8915_DSP1TXL_HPF_WIDTH 1 /* DSP1TXL_HPF */
-#define WM8915_DSP1TXR_HPF 0x0800 /* DSP1TXR_HPF */
-#define WM8915_DSP1TXR_HPF_MASK 0x0800 /* DSP1TXR_HPF */
-#define WM8915_DSP1TXR_HPF_SHIFT 11 /* DSP1TXR_HPF */
-#define WM8915_DSP1TXR_HPF_WIDTH 1 /* DSP1TXR_HPF */
-#define WM8915_DSP1TX_HPF_MODE_MASK 0x0018 /* DSP1TX_HPF_MODE - [4:3] */
-#define WM8915_DSP1TX_HPF_MODE_SHIFT 3 /* DSP1TX_HPF_MODE - [4:3] */
-#define WM8915_DSP1TX_HPF_MODE_WIDTH 2 /* DSP1TX_HPF_MODE - [4:3] */
-#define WM8915_DSP1TX_HPF_CUT_MASK 0x0007 /* DSP1TX_HPF_CUT - [2:0] */
-#define WM8915_DSP1TX_HPF_CUT_SHIFT 0 /* DSP1TX_HPF_CUT - [2:0] */
-#define WM8915_DSP1TX_HPF_CUT_WIDTH 3 /* DSP1TX_HPF_CUT - [2:0] */
-
-/*
- * R1056 (0x420) - DSP1 RX Filters (1)
- */
-#define WM8915_DSP1RX_MUTE 0x0200 /* DSP1RX_MUTE */
-#define WM8915_DSP1RX_MUTE_MASK 0x0200 /* DSP1RX_MUTE */
-#define WM8915_DSP1RX_MUTE_SHIFT 9 /* DSP1RX_MUTE */
-#define WM8915_DSP1RX_MUTE_WIDTH 1 /* DSP1RX_MUTE */
-#define WM8915_DSP1RX_MONO 0x0080 /* DSP1RX_MONO */
-#define WM8915_DSP1RX_MONO_MASK 0x0080 /* DSP1RX_MONO */
-#define WM8915_DSP1RX_MONO_SHIFT 7 /* DSP1RX_MONO */
-#define WM8915_DSP1RX_MONO_WIDTH 1 /* DSP1RX_MONO */
-#define WM8915_DSP1RX_MUTERATE 0x0020 /* DSP1RX_MUTERATE */
-#define WM8915_DSP1RX_MUTERATE_MASK 0x0020 /* DSP1RX_MUTERATE */
-#define WM8915_DSP1RX_MUTERATE_SHIFT 5 /* DSP1RX_MUTERATE */
-#define WM8915_DSP1RX_MUTERATE_WIDTH 1 /* DSP1RX_MUTERATE */
-#define WM8915_DSP1RX_UNMUTE_RAMP 0x0010 /* DSP1RX_UNMUTE_RAMP */
-#define WM8915_DSP1RX_UNMUTE_RAMP_MASK 0x0010 /* DSP1RX_UNMUTE_RAMP */
-#define WM8915_DSP1RX_UNMUTE_RAMP_SHIFT 4 /* DSP1RX_UNMUTE_RAMP */
-#define WM8915_DSP1RX_UNMUTE_RAMP_WIDTH 1 /* DSP1RX_UNMUTE_RAMP */
-
-/*
- * R1057 (0x421) - DSP1 RX Filters (2)
- */
-#define WM8915_DSP1RX_3D_GAIN_MASK 0x3E00 /* DSP1RX_3D_GAIN - [13:9] */
-#define WM8915_DSP1RX_3D_GAIN_SHIFT 9 /* DSP1RX_3D_GAIN - [13:9] */
-#define WM8915_DSP1RX_3D_GAIN_WIDTH 5 /* DSP1RX_3D_GAIN - [13:9] */
-#define WM8915_DSP1RX_3D_ENA 0x0100 /* DSP1RX_3D_ENA */
-#define WM8915_DSP1RX_3D_ENA_MASK 0x0100 /* DSP1RX_3D_ENA */
-#define WM8915_DSP1RX_3D_ENA_SHIFT 8 /* DSP1RX_3D_ENA */
-#define WM8915_DSP1RX_3D_ENA_WIDTH 1 /* DSP1RX_3D_ENA */
-
-/*
- * R1088 (0x440) - DSP1 DRC (1)
- */
-#define WM8915_DSP1DRC_SIG_DET_RMS_MASK 0xF800 /* DSP1DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP1DRC_SIG_DET_RMS_SHIFT 11 /* DSP1DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP1DRC_SIG_DET_RMS_WIDTH 5 /* DSP1DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP1DRC_SIG_DET_PK_MASK 0x0600 /* DSP1DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP1DRC_SIG_DET_PK_SHIFT 9 /* DSP1DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP1DRC_SIG_DET_PK_WIDTH 2 /* DSP1DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP1DRC_NG_ENA 0x0100 /* DSP1DRC_NG_ENA */
-#define WM8915_DSP1DRC_NG_ENA_MASK 0x0100 /* DSP1DRC_NG_ENA */
-#define WM8915_DSP1DRC_NG_ENA_SHIFT 8 /* DSP1DRC_NG_ENA */
-#define WM8915_DSP1DRC_NG_ENA_WIDTH 1 /* DSP1DRC_NG_ENA */
-#define WM8915_DSP1DRC_SIG_DET_MODE 0x0080 /* DSP1DRC_SIG_DET_MODE */
-#define WM8915_DSP1DRC_SIG_DET_MODE_MASK 0x0080 /* DSP1DRC_SIG_DET_MODE */
-#define WM8915_DSP1DRC_SIG_DET_MODE_SHIFT 7 /* DSP1DRC_SIG_DET_MODE */
-#define WM8915_DSP1DRC_SIG_DET_MODE_WIDTH 1 /* DSP1DRC_SIG_DET_MODE */
-#define WM8915_DSP1DRC_SIG_DET 0x0040 /* DSP1DRC_SIG_DET */
-#define WM8915_DSP1DRC_SIG_DET_MASK 0x0040 /* DSP1DRC_SIG_DET */
-#define WM8915_DSP1DRC_SIG_DET_SHIFT 6 /* DSP1DRC_SIG_DET */
-#define WM8915_DSP1DRC_SIG_DET_WIDTH 1 /* DSP1DRC_SIG_DET */
-#define WM8915_DSP1DRC_KNEE2_OP_ENA 0x0020 /* DSP1DRC_KNEE2_OP_ENA */
-#define WM8915_DSP1DRC_KNEE2_OP_ENA_MASK 0x0020 /* DSP1DRC_KNEE2_OP_ENA */
-#define WM8915_DSP1DRC_KNEE2_OP_ENA_SHIFT 5 /* DSP1DRC_KNEE2_OP_ENA */
-#define WM8915_DSP1DRC_KNEE2_OP_ENA_WIDTH 1 /* DSP1DRC_KNEE2_OP_ENA */
-#define WM8915_DSP1DRC_QR 0x0010 /* DSP1DRC_QR */
-#define WM8915_DSP1DRC_QR_MASK 0x0010 /* DSP1DRC_QR */
-#define WM8915_DSP1DRC_QR_SHIFT 4 /* DSP1DRC_QR */
-#define WM8915_DSP1DRC_QR_WIDTH 1 /* DSP1DRC_QR */
-#define WM8915_DSP1DRC_ANTICLIP 0x0008 /* DSP1DRC_ANTICLIP */
-#define WM8915_DSP1DRC_ANTICLIP_MASK 0x0008 /* DSP1DRC_ANTICLIP */
-#define WM8915_DSP1DRC_ANTICLIP_SHIFT 3 /* DSP1DRC_ANTICLIP */
-#define WM8915_DSP1DRC_ANTICLIP_WIDTH 1 /* DSP1DRC_ANTICLIP */
-#define WM8915_DSP1RX_DRC_ENA 0x0004 /* DSP1RX_DRC_ENA */
-#define WM8915_DSP1RX_DRC_ENA_MASK 0x0004 /* DSP1RX_DRC_ENA */
-#define WM8915_DSP1RX_DRC_ENA_SHIFT 2 /* DSP1RX_DRC_ENA */
-#define WM8915_DSP1RX_DRC_ENA_WIDTH 1 /* DSP1RX_DRC_ENA */
-#define WM8915_DSP1TXL_DRC_ENA 0x0002 /* DSP1TXL_DRC_ENA */
-#define WM8915_DSP1TXL_DRC_ENA_MASK 0x0002 /* DSP1TXL_DRC_ENA */
-#define WM8915_DSP1TXL_DRC_ENA_SHIFT 1 /* DSP1TXL_DRC_ENA */
-#define WM8915_DSP1TXL_DRC_ENA_WIDTH 1 /* DSP1TXL_DRC_ENA */
-#define WM8915_DSP1TXR_DRC_ENA 0x0001 /* DSP1TXR_DRC_ENA */
-#define WM8915_DSP1TXR_DRC_ENA_MASK 0x0001 /* DSP1TXR_DRC_ENA */
-#define WM8915_DSP1TXR_DRC_ENA_SHIFT 0 /* DSP1TXR_DRC_ENA */
-#define WM8915_DSP1TXR_DRC_ENA_WIDTH 1 /* DSP1TXR_DRC_ENA */
-
-/*
- * R1089 (0x441) - DSP1 DRC (2)
- */
-#define WM8915_DSP1DRC_ATK_MASK 0x1E00 /* DSP1DRC_ATK - [12:9] */
-#define WM8915_DSP1DRC_ATK_SHIFT 9 /* DSP1DRC_ATK - [12:9] */
-#define WM8915_DSP1DRC_ATK_WIDTH 4 /* DSP1DRC_ATK - [12:9] */
-#define WM8915_DSP1DRC_DCY_MASK 0x01E0 /* DSP1DRC_DCY - [8:5] */
-#define WM8915_DSP1DRC_DCY_SHIFT 5 /* DSP1DRC_DCY - [8:5] */
-#define WM8915_DSP1DRC_DCY_WIDTH 4 /* DSP1DRC_DCY - [8:5] */
-#define WM8915_DSP1DRC_MINGAIN_MASK 0x001C /* DSP1DRC_MINGAIN - [4:2] */
-#define WM8915_DSP1DRC_MINGAIN_SHIFT 2 /* DSP1DRC_MINGAIN - [4:2] */
-#define WM8915_DSP1DRC_MINGAIN_WIDTH 3 /* DSP1DRC_MINGAIN - [4:2] */
-#define WM8915_DSP1DRC_MAXGAIN_MASK 0x0003 /* DSP1DRC_MAXGAIN - [1:0] */
-#define WM8915_DSP1DRC_MAXGAIN_SHIFT 0 /* DSP1DRC_MAXGAIN - [1:0] */
-#define WM8915_DSP1DRC_MAXGAIN_WIDTH 2 /* DSP1DRC_MAXGAIN - [1:0] */
-
-/*
- * R1090 (0x442) - DSP1 DRC (3)
- */
-#define WM8915_DSP1DRC_NG_MINGAIN_MASK 0xF000 /* DSP1DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP1DRC_NG_MINGAIN_SHIFT 12 /* DSP1DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP1DRC_NG_MINGAIN_WIDTH 4 /* DSP1DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP1DRC_NG_EXP_MASK 0x0C00 /* DSP1DRC_NG_EXP - [11:10] */
-#define WM8915_DSP1DRC_NG_EXP_SHIFT 10 /* DSP1DRC_NG_EXP - [11:10] */
-#define WM8915_DSP1DRC_NG_EXP_WIDTH 2 /* DSP1DRC_NG_EXP - [11:10] */
-#define WM8915_DSP1DRC_QR_THR_MASK 0x0300 /* DSP1DRC_QR_THR - [9:8] */
-#define WM8915_DSP1DRC_QR_THR_SHIFT 8 /* DSP1DRC_QR_THR - [9:8] */
-#define WM8915_DSP1DRC_QR_THR_WIDTH 2 /* DSP1DRC_QR_THR - [9:8] */
-#define WM8915_DSP1DRC_QR_DCY_MASK 0x00C0 /* DSP1DRC_QR_DCY - [7:6] */
-#define WM8915_DSP1DRC_QR_DCY_SHIFT 6 /* DSP1DRC_QR_DCY - [7:6] */
-#define WM8915_DSP1DRC_QR_DCY_WIDTH 2 /* DSP1DRC_QR_DCY - [7:6] */
-#define WM8915_DSP1DRC_HI_COMP_MASK 0x0038 /* DSP1DRC_HI_COMP - [5:3] */
-#define WM8915_DSP1DRC_HI_COMP_SHIFT 3 /* DSP1DRC_HI_COMP - [5:3] */
-#define WM8915_DSP1DRC_HI_COMP_WIDTH 3 /* DSP1DRC_HI_COMP - [5:3] */
-#define WM8915_DSP1DRC_LO_COMP_MASK 0x0007 /* DSP1DRC_LO_COMP - [2:0] */
-#define WM8915_DSP1DRC_LO_COMP_SHIFT 0 /* DSP1DRC_LO_COMP - [2:0] */
-#define WM8915_DSP1DRC_LO_COMP_WIDTH 3 /* DSP1DRC_LO_COMP - [2:0] */
-
-/*
- * R1091 (0x443) - DSP1 DRC (4)
- */
-#define WM8915_DSP1DRC_KNEE_IP_MASK 0x07E0 /* DSP1DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP1DRC_KNEE_IP_SHIFT 5 /* DSP1DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP1DRC_KNEE_IP_WIDTH 6 /* DSP1DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP1DRC_KNEE_OP_MASK 0x001F /* DSP1DRC_KNEE_OP - [4:0] */
-#define WM8915_DSP1DRC_KNEE_OP_SHIFT 0 /* DSP1DRC_KNEE_OP - [4:0] */
-#define WM8915_DSP1DRC_KNEE_OP_WIDTH 5 /* DSP1DRC_KNEE_OP - [4:0] */
-
-/*
- * R1092 (0x444) - DSP1 DRC (5)
- */
-#define WM8915_DSP1DRC_KNEE2_IP_MASK 0x03E0 /* DSP1DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP1DRC_KNEE2_IP_SHIFT 5 /* DSP1DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP1DRC_KNEE2_IP_WIDTH 5 /* DSP1DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP1DRC_KNEE2_OP_MASK 0x001F /* DSP1DRC_KNEE2_OP - [4:0] */
-#define WM8915_DSP1DRC_KNEE2_OP_SHIFT 0 /* DSP1DRC_KNEE2_OP - [4:0] */
-#define WM8915_DSP1DRC_KNEE2_OP_WIDTH 5 /* DSP1DRC_KNEE2_OP - [4:0] */
-
-/*
- * R1152 (0x480) - DSP1 RX EQ Gains (1)
- */
-#define WM8915_DSP1RX_EQ_B1_GAIN_MASK 0xF800 /* DSP1RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B1_GAIN_SHIFT 11 /* DSP1RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B1_GAIN_WIDTH 5 /* DSP1RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B2_GAIN_MASK 0x07C0 /* DSP1RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP1RX_EQ_B2_GAIN_SHIFT 6 /* DSP1RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP1RX_EQ_B2_GAIN_WIDTH 5 /* DSP1RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP1RX_EQ_B3_GAIN_MASK 0x003E /* DSP1RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP1RX_EQ_B3_GAIN_SHIFT 1 /* DSP1RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP1RX_EQ_B3_GAIN_WIDTH 5 /* DSP1RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP1RX_EQ_ENA 0x0001 /* DSP1RX_EQ_ENA */
-#define WM8915_DSP1RX_EQ_ENA_MASK 0x0001 /* DSP1RX_EQ_ENA */
-#define WM8915_DSP1RX_EQ_ENA_SHIFT 0 /* DSP1RX_EQ_ENA */
-#define WM8915_DSP1RX_EQ_ENA_WIDTH 1 /* DSP1RX_EQ_ENA */
-
-/*
- * R1153 (0x481) - DSP1 RX EQ Gains (2)
- */
-#define WM8915_DSP1RX_EQ_B4_GAIN_MASK 0xF800 /* DSP1RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B4_GAIN_SHIFT 11 /* DSP1RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B4_GAIN_WIDTH 5 /* DSP1RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP1RX_EQ_B5_GAIN_MASK 0x07C0 /* DSP1RX_EQ_B5_GAIN - [10:6] */
-#define WM8915_DSP1RX_EQ_B5_GAIN_SHIFT 6 /* DSP1RX_EQ_B5_GAIN - [10:6] */
-#define WM8915_DSP1RX_EQ_B5_GAIN_WIDTH 5 /* DSP1RX_EQ_B5_GAIN - [10:6] */
-
-/*
- * R1154 (0x482) - DSP1 RX EQ Band 1 A
- */
-#define WM8915_DSP1RX_EQ_B1_A_MASK 0xFFFF /* DSP1RX_EQ_B1_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_A_SHIFT 0 /* DSP1RX_EQ_B1_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_A_WIDTH 16 /* DSP1RX_EQ_B1_A - [15:0] */
-
-/*
- * R1155 (0x483) - DSP1 RX EQ Band 1 B
- */
-#define WM8915_DSP1RX_EQ_B1_B_MASK 0xFFFF /* DSP1RX_EQ_B1_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_B_SHIFT 0 /* DSP1RX_EQ_B1_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_B_WIDTH 16 /* DSP1RX_EQ_B1_B - [15:0] */
-
-/*
- * R1156 (0x484) - DSP1 RX EQ Band 1 PG
- */
-#define WM8915_DSP1RX_EQ_B1_PG_MASK 0xFFFF /* DSP1RX_EQ_B1_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_PG_SHIFT 0 /* DSP1RX_EQ_B1_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B1_PG_WIDTH 16 /* DSP1RX_EQ_B1_PG - [15:0] */
-
-/*
- * R1157 (0x485) - DSP1 RX EQ Band 2 A
- */
-#define WM8915_DSP1RX_EQ_B2_A_MASK 0xFFFF /* DSP1RX_EQ_B2_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_A_SHIFT 0 /* DSP1RX_EQ_B2_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_A_WIDTH 16 /* DSP1RX_EQ_B2_A - [15:0] */
-
-/*
- * R1158 (0x486) - DSP1 RX EQ Band 2 B
- */
-#define WM8915_DSP1RX_EQ_B2_B_MASK 0xFFFF /* DSP1RX_EQ_B2_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_B_SHIFT 0 /* DSP1RX_EQ_B2_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_B_WIDTH 16 /* DSP1RX_EQ_B2_B - [15:0] */
-
-/*
- * R1159 (0x487) - DSP1 RX EQ Band 2 C
- */
-#define WM8915_DSP1RX_EQ_B2_C_MASK 0xFFFF /* DSP1RX_EQ_B2_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_C_SHIFT 0 /* DSP1RX_EQ_B2_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_C_WIDTH 16 /* DSP1RX_EQ_B2_C - [15:0] */
-
-/*
- * R1160 (0x488) - DSP1 RX EQ Band 2 PG
- */
-#define WM8915_DSP1RX_EQ_B2_PG_MASK 0xFFFF /* DSP1RX_EQ_B2_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_PG_SHIFT 0 /* DSP1RX_EQ_B2_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B2_PG_WIDTH 16 /* DSP1RX_EQ_B2_PG - [15:0] */
-
-/*
- * R1161 (0x489) - DSP1 RX EQ Band 3 A
- */
-#define WM8915_DSP1RX_EQ_B3_A_MASK 0xFFFF /* DSP1RX_EQ_B3_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_A_SHIFT 0 /* DSP1RX_EQ_B3_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_A_WIDTH 16 /* DSP1RX_EQ_B3_A - [15:0] */
-
-/*
- * R1162 (0x48A) - DSP1 RX EQ Band 3 B
- */
-#define WM8915_DSP1RX_EQ_B3_B_MASK 0xFFFF /* DSP1RX_EQ_B3_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_B_SHIFT 0 /* DSP1RX_EQ_B3_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_B_WIDTH 16 /* DSP1RX_EQ_B3_B - [15:0] */
-
-/*
- * R1163 (0x48B) - DSP1 RX EQ Band 3 C
- */
-#define WM8915_DSP1RX_EQ_B3_C_MASK 0xFFFF /* DSP1RX_EQ_B3_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_C_SHIFT 0 /* DSP1RX_EQ_B3_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_C_WIDTH 16 /* DSP1RX_EQ_B3_C - [15:0] */
-
-/*
- * R1164 (0x48C) - DSP1 RX EQ Band 3 PG
- */
-#define WM8915_DSP1RX_EQ_B3_PG_MASK 0xFFFF /* DSP1RX_EQ_B3_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_PG_SHIFT 0 /* DSP1RX_EQ_B3_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B3_PG_WIDTH 16 /* DSP1RX_EQ_B3_PG - [15:0] */
-
-/*
- * R1165 (0x48D) - DSP1 RX EQ Band 4 A
- */
-#define WM8915_DSP1RX_EQ_B4_A_MASK 0xFFFF /* DSP1RX_EQ_B4_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_A_SHIFT 0 /* DSP1RX_EQ_B4_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_A_WIDTH 16 /* DSP1RX_EQ_B4_A - [15:0] */
-
-/*
- * R1166 (0x48E) - DSP1 RX EQ Band 4 B
- */
-#define WM8915_DSP1RX_EQ_B4_B_MASK 0xFFFF /* DSP1RX_EQ_B4_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_B_SHIFT 0 /* DSP1RX_EQ_B4_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_B_WIDTH 16 /* DSP1RX_EQ_B4_B - [15:0] */
-
-/*
- * R1167 (0x48F) - DSP1 RX EQ Band 4 C
- */
-#define WM8915_DSP1RX_EQ_B4_C_MASK 0xFFFF /* DSP1RX_EQ_B4_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_C_SHIFT 0 /* DSP1RX_EQ_B4_C - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_C_WIDTH 16 /* DSP1RX_EQ_B4_C - [15:0] */
-
-/*
- * R1168 (0x490) - DSP1 RX EQ Band 4 PG
- */
-#define WM8915_DSP1RX_EQ_B4_PG_MASK 0xFFFF /* DSP1RX_EQ_B4_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_PG_SHIFT 0 /* DSP1RX_EQ_B4_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B4_PG_WIDTH 16 /* DSP1RX_EQ_B4_PG - [15:0] */
-
-/*
- * R1169 (0x491) - DSP1 RX EQ Band 5 A
- */
-#define WM8915_DSP1RX_EQ_B5_A_MASK 0xFFFF /* DSP1RX_EQ_B5_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_A_SHIFT 0 /* DSP1RX_EQ_B5_A - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_A_WIDTH 16 /* DSP1RX_EQ_B5_A - [15:0] */
-
-/*
- * R1170 (0x492) - DSP1 RX EQ Band 5 B
- */
-#define WM8915_DSP1RX_EQ_B5_B_MASK 0xFFFF /* DSP1RX_EQ_B5_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_B_SHIFT 0 /* DSP1RX_EQ_B5_B - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_B_WIDTH 16 /* DSP1RX_EQ_B5_B - [15:0] */
-
-/*
- * R1171 (0x493) - DSP1 RX EQ Band 5 PG
- */
-#define WM8915_DSP1RX_EQ_B5_PG_MASK 0xFFFF /* DSP1RX_EQ_B5_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_PG_SHIFT 0 /* DSP1RX_EQ_B5_PG - [15:0] */
-#define WM8915_DSP1RX_EQ_B5_PG_WIDTH 16 /* DSP1RX_EQ_B5_PG - [15:0] */
-
-/*
- * R1280 (0x500) - DSP2 TX Left Volume
- */
-#define WM8915_DSP2TX_VU 0x0100 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_MASK 0x0100 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_SHIFT 8 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_WIDTH 1 /* DSP2TX_VU */
-#define WM8915_DSP2TXL_VOL_MASK 0x00FF /* DSP2TXL_VOL - [7:0] */
-#define WM8915_DSP2TXL_VOL_SHIFT 0 /* DSP2TXL_VOL - [7:0] */
-#define WM8915_DSP2TXL_VOL_WIDTH 8 /* DSP2TXL_VOL - [7:0] */
-
-/*
- * R1281 (0x501) - DSP2 TX Right Volume
- */
-#define WM8915_DSP2TX_VU 0x0100 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_MASK 0x0100 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_SHIFT 8 /* DSP2TX_VU */
-#define WM8915_DSP2TX_VU_WIDTH 1 /* DSP2TX_VU */
-#define WM8915_DSP2TXR_VOL_MASK 0x00FF /* DSP2TXR_VOL - [7:0] */
-#define WM8915_DSP2TXR_VOL_SHIFT 0 /* DSP2TXR_VOL - [7:0] */
-#define WM8915_DSP2TXR_VOL_WIDTH 8 /* DSP2TXR_VOL - [7:0] */
-
-/*
- * R1282 (0x502) - DSP2 RX Left Volume
- */
-#define WM8915_DSP2RX_VU 0x0100 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_MASK 0x0100 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_SHIFT 8 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_WIDTH 1 /* DSP2RX_VU */
-#define WM8915_DSP2RXL_VOL_MASK 0x00FF /* DSP2RXL_VOL - [7:0] */
-#define WM8915_DSP2RXL_VOL_SHIFT 0 /* DSP2RXL_VOL - [7:0] */
-#define WM8915_DSP2RXL_VOL_WIDTH 8 /* DSP2RXL_VOL - [7:0] */
-
-/*
- * R1283 (0x503) - DSP2 RX Right Volume
- */
-#define WM8915_DSP2RX_VU 0x0100 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_MASK 0x0100 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_SHIFT 8 /* DSP2RX_VU */
-#define WM8915_DSP2RX_VU_WIDTH 1 /* DSP2RX_VU */
-#define WM8915_DSP2RXR_VOL_MASK 0x00FF /* DSP2RXR_VOL - [7:0] */
-#define WM8915_DSP2RXR_VOL_SHIFT 0 /* DSP2RXR_VOL - [7:0] */
-#define WM8915_DSP2RXR_VOL_WIDTH 8 /* DSP2RXR_VOL - [7:0] */
-
-/*
- * R1296 (0x510) - DSP2 TX Filters
- */
-#define WM8915_DSP2TX_NF 0x2000 /* DSP2TX_NF */
-#define WM8915_DSP2TX_NF_MASK 0x2000 /* DSP2TX_NF */
-#define WM8915_DSP2TX_NF_SHIFT 13 /* DSP2TX_NF */
-#define WM8915_DSP2TX_NF_WIDTH 1 /* DSP2TX_NF */
-#define WM8915_DSP2TXL_HPF 0x1000 /* DSP2TXL_HPF */
-#define WM8915_DSP2TXL_HPF_MASK 0x1000 /* DSP2TXL_HPF */
-#define WM8915_DSP2TXL_HPF_SHIFT 12 /* DSP2TXL_HPF */
-#define WM8915_DSP2TXL_HPF_WIDTH 1 /* DSP2TXL_HPF */
-#define WM8915_DSP2TXR_HPF 0x0800 /* DSP2TXR_HPF */
-#define WM8915_DSP2TXR_HPF_MASK 0x0800 /* DSP2TXR_HPF */
-#define WM8915_DSP2TXR_HPF_SHIFT 11 /* DSP2TXR_HPF */
-#define WM8915_DSP2TXR_HPF_WIDTH 1 /* DSP2TXR_HPF */
-#define WM8915_DSP2TX_HPF_MODE_MASK 0x0018 /* DSP2TX_HPF_MODE - [4:3] */
-#define WM8915_DSP2TX_HPF_MODE_SHIFT 3 /* DSP2TX_HPF_MODE - [4:3] */
-#define WM8915_DSP2TX_HPF_MODE_WIDTH 2 /* DSP2TX_HPF_MODE - [4:3] */
-#define WM8915_DSP2TX_HPF_CUT_MASK 0x0007 /* DSP2TX_HPF_CUT - [2:0] */
-#define WM8915_DSP2TX_HPF_CUT_SHIFT 0 /* DSP2TX_HPF_CUT - [2:0] */
-#define WM8915_DSP2TX_HPF_CUT_WIDTH 3 /* DSP2TX_HPF_CUT - [2:0] */
-
-/*
- * R1312 (0x520) - DSP2 RX Filters (1)
- */
-#define WM8915_DSP2RX_MUTE 0x0200 /* DSP2RX_MUTE */
-#define WM8915_DSP2RX_MUTE_MASK 0x0200 /* DSP2RX_MUTE */
-#define WM8915_DSP2RX_MUTE_SHIFT 9 /* DSP2RX_MUTE */
-#define WM8915_DSP2RX_MUTE_WIDTH 1 /* DSP2RX_MUTE */
-#define WM8915_DSP2RX_MONO 0x0080 /* DSP2RX_MONO */
-#define WM8915_DSP2RX_MONO_MASK 0x0080 /* DSP2RX_MONO */
-#define WM8915_DSP2RX_MONO_SHIFT 7 /* DSP2RX_MONO */
-#define WM8915_DSP2RX_MONO_WIDTH 1 /* DSP2RX_MONO */
-#define WM8915_DSP2RX_MUTERATE 0x0020 /* DSP2RX_MUTERATE */
-#define WM8915_DSP2RX_MUTERATE_MASK 0x0020 /* DSP2RX_MUTERATE */
-#define WM8915_DSP2RX_MUTERATE_SHIFT 5 /* DSP2RX_MUTERATE */
-#define WM8915_DSP2RX_MUTERATE_WIDTH 1 /* DSP2RX_MUTERATE */
-#define WM8915_DSP2RX_UNMUTE_RAMP 0x0010 /* DSP2RX_UNMUTE_RAMP */
-#define WM8915_DSP2RX_UNMUTE_RAMP_MASK 0x0010 /* DSP2RX_UNMUTE_RAMP */
-#define WM8915_DSP2RX_UNMUTE_RAMP_SHIFT 4 /* DSP2RX_UNMUTE_RAMP */
-#define WM8915_DSP2RX_UNMUTE_RAMP_WIDTH 1 /* DSP2RX_UNMUTE_RAMP */
-
-/*
- * R1313 (0x521) - DSP2 RX Filters (2)
- */
-#define WM8915_DSP2RX_3D_GAIN_MASK 0x3E00 /* DSP2RX_3D_GAIN - [13:9] */
-#define WM8915_DSP2RX_3D_GAIN_SHIFT 9 /* DSP2RX_3D_GAIN - [13:9] */
-#define WM8915_DSP2RX_3D_GAIN_WIDTH 5 /* DSP2RX_3D_GAIN - [13:9] */
-#define WM8915_DSP2RX_3D_ENA 0x0100 /* DSP2RX_3D_ENA */
-#define WM8915_DSP2RX_3D_ENA_MASK 0x0100 /* DSP2RX_3D_ENA */
-#define WM8915_DSP2RX_3D_ENA_SHIFT 8 /* DSP2RX_3D_ENA */
-#define WM8915_DSP2RX_3D_ENA_WIDTH 1 /* DSP2RX_3D_ENA */
-
-/*
- * R1344 (0x540) - DSP2 DRC (1)
- */
-#define WM8915_DSP2DRC_SIG_DET_RMS_MASK 0xF800 /* DSP2DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP2DRC_SIG_DET_RMS_SHIFT 11 /* DSP2DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP2DRC_SIG_DET_RMS_WIDTH 5 /* DSP2DRC_SIG_DET_RMS - [15:11] */
-#define WM8915_DSP2DRC_SIG_DET_PK_MASK 0x0600 /* DSP2DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP2DRC_SIG_DET_PK_SHIFT 9 /* DSP2DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP2DRC_SIG_DET_PK_WIDTH 2 /* DSP2DRC_SIG_DET_PK - [10:9] */
-#define WM8915_DSP2DRC_NG_ENA 0x0100 /* DSP2DRC_NG_ENA */
-#define WM8915_DSP2DRC_NG_ENA_MASK 0x0100 /* DSP2DRC_NG_ENA */
-#define WM8915_DSP2DRC_NG_ENA_SHIFT 8 /* DSP2DRC_NG_ENA */
-#define WM8915_DSP2DRC_NG_ENA_WIDTH 1 /* DSP2DRC_NG_ENA */
-#define WM8915_DSP2DRC_SIG_DET_MODE 0x0080 /* DSP2DRC_SIG_DET_MODE */
-#define WM8915_DSP2DRC_SIG_DET_MODE_MASK 0x0080 /* DSP2DRC_SIG_DET_MODE */
-#define WM8915_DSP2DRC_SIG_DET_MODE_SHIFT 7 /* DSP2DRC_SIG_DET_MODE */
-#define WM8915_DSP2DRC_SIG_DET_MODE_WIDTH 1 /* DSP2DRC_SIG_DET_MODE */
-#define WM8915_DSP2DRC_SIG_DET 0x0040 /* DSP2DRC_SIG_DET */
-#define WM8915_DSP2DRC_SIG_DET_MASK 0x0040 /* DSP2DRC_SIG_DET */
-#define WM8915_DSP2DRC_SIG_DET_SHIFT 6 /* DSP2DRC_SIG_DET */
-#define WM8915_DSP2DRC_SIG_DET_WIDTH 1 /* DSP2DRC_SIG_DET */
-#define WM8915_DSP2DRC_KNEE2_OP_ENA 0x0020 /* DSP2DRC_KNEE2_OP_ENA */
-#define WM8915_DSP2DRC_KNEE2_OP_ENA_MASK 0x0020 /* DSP2DRC_KNEE2_OP_ENA */
-#define WM8915_DSP2DRC_KNEE2_OP_ENA_SHIFT 5 /* DSP2DRC_KNEE2_OP_ENA */
-#define WM8915_DSP2DRC_KNEE2_OP_ENA_WIDTH 1 /* DSP2DRC_KNEE2_OP_ENA */
-#define WM8915_DSP2DRC_QR 0x0010 /* DSP2DRC_QR */
-#define WM8915_DSP2DRC_QR_MASK 0x0010 /* DSP2DRC_QR */
-#define WM8915_DSP2DRC_QR_SHIFT 4 /* DSP2DRC_QR */
-#define WM8915_DSP2DRC_QR_WIDTH 1 /* DSP2DRC_QR */
-#define WM8915_DSP2DRC_ANTICLIP 0x0008 /* DSP2DRC_ANTICLIP */
-#define WM8915_DSP2DRC_ANTICLIP_MASK 0x0008 /* DSP2DRC_ANTICLIP */
-#define WM8915_DSP2DRC_ANTICLIP_SHIFT 3 /* DSP2DRC_ANTICLIP */
-#define WM8915_DSP2DRC_ANTICLIP_WIDTH 1 /* DSP2DRC_ANTICLIP */
-#define WM8915_DSP2RX_DRC_ENA 0x0004 /* DSP2RX_DRC_ENA */
-#define WM8915_DSP2RX_DRC_ENA_MASK 0x0004 /* DSP2RX_DRC_ENA */
-#define WM8915_DSP2RX_DRC_ENA_SHIFT 2 /* DSP2RX_DRC_ENA */
-#define WM8915_DSP2RX_DRC_ENA_WIDTH 1 /* DSP2RX_DRC_ENA */
-#define WM8915_DSP2TXL_DRC_ENA 0x0002 /* DSP2TXL_DRC_ENA */
-#define WM8915_DSP2TXL_DRC_ENA_MASK 0x0002 /* DSP2TXL_DRC_ENA */
-#define WM8915_DSP2TXL_DRC_ENA_SHIFT 1 /* DSP2TXL_DRC_ENA */
-#define WM8915_DSP2TXL_DRC_ENA_WIDTH 1 /* DSP2TXL_DRC_ENA */
-#define WM8915_DSP2TXR_DRC_ENA 0x0001 /* DSP2TXR_DRC_ENA */
-#define WM8915_DSP2TXR_DRC_ENA_MASK 0x0001 /* DSP2TXR_DRC_ENA */
-#define WM8915_DSP2TXR_DRC_ENA_SHIFT 0 /* DSP2TXR_DRC_ENA */
-#define WM8915_DSP2TXR_DRC_ENA_WIDTH 1 /* DSP2TXR_DRC_ENA */
-
-/*
- * R1345 (0x541) - DSP2 DRC (2)
- */
-#define WM8915_DSP2DRC_ATK_MASK 0x1E00 /* DSP2DRC_ATK - [12:9] */
-#define WM8915_DSP2DRC_ATK_SHIFT 9 /* DSP2DRC_ATK - [12:9] */
-#define WM8915_DSP2DRC_ATK_WIDTH 4 /* DSP2DRC_ATK - [12:9] */
-#define WM8915_DSP2DRC_DCY_MASK 0x01E0 /* DSP2DRC_DCY - [8:5] */
-#define WM8915_DSP2DRC_DCY_SHIFT 5 /* DSP2DRC_DCY - [8:5] */
-#define WM8915_DSP2DRC_DCY_WIDTH 4 /* DSP2DRC_DCY - [8:5] */
-#define WM8915_DSP2DRC_MINGAIN_MASK 0x001C /* DSP2DRC_MINGAIN - [4:2] */
-#define WM8915_DSP2DRC_MINGAIN_SHIFT 2 /* DSP2DRC_MINGAIN - [4:2] */
-#define WM8915_DSP2DRC_MINGAIN_WIDTH 3 /* DSP2DRC_MINGAIN - [4:2] */
-#define WM8915_DSP2DRC_MAXGAIN_MASK 0x0003 /* DSP2DRC_MAXGAIN - [1:0] */
-#define WM8915_DSP2DRC_MAXGAIN_SHIFT 0 /* DSP2DRC_MAXGAIN - [1:0] */
-#define WM8915_DSP2DRC_MAXGAIN_WIDTH 2 /* DSP2DRC_MAXGAIN - [1:0] */
-
-/*
- * R1346 (0x542) - DSP2 DRC (3)
- */
-#define WM8915_DSP2DRC_NG_MINGAIN_MASK 0xF000 /* DSP2DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP2DRC_NG_MINGAIN_SHIFT 12 /* DSP2DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP2DRC_NG_MINGAIN_WIDTH 4 /* DSP2DRC_NG_MINGAIN - [15:12] */
-#define WM8915_DSP2DRC_NG_EXP_MASK 0x0C00 /* DSP2DRC_NG_EXP - [11:10] */
-#define WM8915_DSP2DRC_NG_EXP_SHIFT 10 /* DSP2DRC_NG_EXP - [11:10] */
-#define WM8915_DSP2DRC_NG_EXP_WIDTH 2 /* DSP2DRC_NG_EXP - [11:10] */
-#define WM8915_DSP2DRC_QR_THR_MASK 0x0300 /* DSP2DRC_QR_THR - [9:8] */
-#define WM8915_DSP2DRC_QR_THR_SHIFT 8 /* DSP2DRC_QR_THR - [9:8] */
-#define WM8915_DSP2DRC_QR_THR_WIDTH 2 /* DSP2DRC_QR_THR - [9:8] */
-#define WM8915_DSP2DRC_QR_DCY_MASK 0x00C0 /* DSP2DRC_QR_DCY - [7:6] */
-#define WM8915_DSP2DRC_QR_DCY_SHIFT 6 /* DSP2DRC_QR_DCY - [7:6] */
-#define WM8915_DSP2DRC_QR_DCY_WIDTH 2 /* DSP2DRC_QR_DCY - [7:6] */
-#define WM8915_DSP2DRC_HI_COMP_MASK 0x0038 /* DSP2DRC_HI_COMP - [5:3] */
-#define WM8915_DSP2DRC_HI_COMP_SHIFT 3 /* DSP2DRC_HI_COMP - [5:3] */
-#define WM8915_DSP2DRC_HI_COMP_WIDTH 3 /* DSP2DRC_HI_COMP - [5:3] */
-#define WM8915_DSP2DRC_LO_COMP_MASK 0x0007 /* DSP2DRC_LO_COMP - [2:0] */
-#define WM8915_DSP2DRC_LO_COMP_SHIFT 0 /* DSP2DRC_LO_COMP - [2:0] */
-#define WM8915_DSP2DRC_LO_COMP_WIDTH 3 /* DSP2DRC_LO_COMP - [2:0] */
-
-/*
- * R1347 (0x543) - DSP2 DRC (4)
- */
-#define WM8915_DSP2DRC_KNEE_IP_MASK 0x07E0 /* DSP2DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP2DRC_KNEE_IP_SHIFT 5 /* DSP2DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP2DRC_KNEE_IP_WIDTH 6 /* DSP2DRC_KNEE_IP - [10:5] */
-#define WM8915_DSP2DRC_KNEE_OP_MASK 0x001F /* DSP2DRC_KNEE_OP - [4:0] */
-#define WM8915_DSP2DRC_KNEE_OP_SHIFT 0 /* DSP2DRC_KNEE_OP - [4:0] */
-#define WM8915_DSP2DRC_KNEE_OP_WIDTH 5 /* DSP2DRC_KNEE_OP - [4:0] */
-
-/*
- * R1348 (0x544) - DSP2 DRC (5)
- */
-#define WM8915_DSP2DRC_KNEE2_IP_MASK 0x03E0 /* DSP2DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP2DRC_KNEE2_IP_SHIFT 5 /* DSP2DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP2DRC_KNEE2_IP_WIDTH 5 /* DSP2DRC_KNEE2_IP - [9:5] */
-#define WM8915_DSP2DRC_KNEE2_OP_MASK 0x001F /* DSP2DRC_KNEE2_OP - [4:0] */
-#define WM8915_DSP2DRC_KNEE2_OP_SHIFT 0 /* DSP2DRC_KNEE2_OP - [4:0] */
-#define WM8915_DSP2DRC_KNEE2_OP_WIDTH 5 /* DSP2DRC_KNEE2_OP - [4:0] */
-
-/*
- * R1408 (0x580) - DSP2 RX EQ Gains (1)
- */
-#define WM8915_DSP2RX_EQ_B1_GAIN_MASK 0xF800 /* DSP2RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B1_GAIN_SHIFT 11 /* DSP2RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B1_GAIN_WIDTH 5 /* DSP2RX_EQ_B1_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B2_GAIN_MASK 0x07C0 /* DSP2RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP2RX_EQ_B2_GAIN_SHIFT 6 /* DSP2RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP2RX_EQ_B2_GAIN_WIDTH 5 /* DSP2RX_EQ_B2_GAIN - [10:6] */
-#define WM8915_DSP2RX_EQ_B3_GAIN_MASK 0x003E /* DSP2RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP2RX_EQ_B3_GAIN_SHIFT 1 /* DSP2RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP2RX_EQ_B3_GAIN_WIDTH 5 /* DSP2RX_EQ_B3_GAIN - [5:1] */
-#define WM8915_DSP2RX_EQ_ENA 0x0001 /* DSP2RX_EQ_ENA */
-#define WM8915_DSP2RX_EQ_ENA_MASK 0x0001 /* DSP2RX_EQ_ENA */
-#define WM8915_DSP2RX_EQ_ENA_SHIFT 0 /* DSP2RX_EQ_ENA */
-#define WM8915_DSP2RX_EQ_ENA_WIDTH 1 /* DSP2RX_EQ_ENA */
-
-/*
- * R1409 (0x581) - DSP2 RX EQ Gains (2)
- */
-#define WM8915_DSP2RX_EQ_B4_GAIN_MASK 0xF800 /* DSP2RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B4_GAIN_SHIFT 11 /* DSP2RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B4_GAIN_WIDTH 5 /* DSP2RX_EQ_B4_GAIN - [15:11] */
-#define WM8915_DSP2RX_EQ_B5_GAIN_MASK 0x07C0 /* DSP2RX_EQ_B5_GAIN - [10:6] */
-#define WM8915_DSP2RX_EQ_B5_GAIN_SHIFT 6 /* DSP2RX_EQ_B5_GAIN - [10:6] */
-#define WM8915_DSP2RX_EQ_B5_GAIN_WIDTH 5 /* DSP2RX_EQ_B5_GAIN - [10:6] */
-
-/*
- * R1410 (0x582) - DSP2 RX EQ Band 1 A
- */
-#define WM8915_DSP2RX_EQ_B1_A_MASK 0xFFFF /* DSP2RX_EQ_B1_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_A_SHIFT 0 /* DSP2RX_EQ_B1_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_A_WIDTH 16 /* DSP2RX_EQ_B1_A - [15:0] */
-
-/*
- * R1411 (0x583) - DSP2 RX EQ Band 1 B
- */
-#define WM8915_DSP2RX_EQ_B1_B_MASK 0xFFFF /* DSP2RX_EQ_B1_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_B_SHIFT 0 /* DSP2RX_EQ_B1_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_B_WIDTH 16 /* DSP2RX_EQ_B1_B - [15:0] */
-
-/*
- * R1412 (0x584) - DSP2 RX EQ Band 1 PG
- */
-#define WM8915_DSP2RX_EQ_B1_PG_MASK 0xFFFF /* DSP2RX_EQ_B1_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_PG_SHIFT 0 /* DSP2RX_EQ_B1_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B1_PG_WIDTH 16 /* DSP2RX_EQ_B1_PG - [15:0] */
-
-/*
- * R1413 (0x585) - DSP2 RX EQ Band 2 A
- */
-#define WM8915_DSP2RX_EQ_B2_A_MASK 0xFFFF /* DSP2RX_EQ_B2_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_A_SHIFT 0 /* DSP2RX_EQ_B2_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_A_WIDTH 16 /* DSP2RX_EQ_B2_A - [15:0] */
-
-/*
- * R1414 (0x586) - DSP2 RX EQ Band 2 B
- */
-#define WM8915_DSP2RX_EQ_B2_B_MASK 0xFFFF /* DSP2RX_EQ_B2_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_B_SHIFT 0 /* DSP2RX_EQ_B2_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_B_WIDTH 16 /* DSP2RX_EQ_B2_B - [15:0] */
-
-/*
- * R1415 (0x587) - DSP2 RX EQ Band 2 C
- */
-#define WM8915_DSP2RX_EQ_B2_C_MASK 0xFFFF /* DSP2RX_EQ_B2_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_C_SHIFT 0 /* DSP2RX_EQ_B2_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_C_WIDTH 16 /* DSP2RX_EQ_B2_C - [15:0] */
-
-/*
- * R1416 (0x588) - DSP2 RX EQ Band 2 PG
- */
-#define WM8915_DSP2RX_EQ_B2_PG_MASK 0xFFFF /* DSP2RX_EQ_B2_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_PG_SHIFT 0 /* DSP2RX_EQ_B2_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B2_PG_WIDTH 16 /* DSP2RX_EQ_B2_PG - [15:0] */
-
-/*
- * R1417 (0x589) - DSP2 RX EQ Band 3 A
- */
-#define WM8915_DSP2RX_EQ_B3_A_MASK 0xFFFF /* DSP2RX_EQ_B3_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_A_SHIFT 0 /* DSP2RX_EQ_B3_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_A_WIDTH 16 /* DSP2RX_EQ_B3_A - [15:0] */
-
-/*
- * R1418 (0x58A) - DSP2 RX EQ Band 3 B
- */
-#define WM8915_DSP2RX_EQ_B3_B_MASK 0xFFFF /* DSP2RX_EQ_B3_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_B_SHIFT 0 /* DSP2RX_EQ_B3_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_B_WIDTH 16 /* DSP2RX_EQ_B3_B - [15:0] */
-
-/*
- * R1419 (0x58B) - DSP2 RX EQ Band 3 C
- */
-#define WM8915_DSP2RX_EQ_B3_C_MASK 0xFFFF /* DSP2RX_EQ_B3_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_C_SHIFT 0 /* DSP2RX_EQ_B3_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_C_WIDTH 16 /* DSP2RX_EQ_B3_C - [15:0] */
-
-/*
- * R1420 (0x58C) - DSP2 RX EQ Band 3 PG
- */
-#define WM8915_DSP2RX_EQ_B3_PG_MASK 0xFFFF /* DSP2RX_EQ_B3_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_PG_SHIFT 0 /* DSP2RX_EQ_B3_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B3_PG_WIDTH 16 /* DSP2RX_EQ_B3_PG - [15:0] */
-
-/*
- * R1421 (0x58D) - DSP2 RX EQ Band 4 A
- */
-#define WM8915_DSP2RX_EQ_B4_A_MASK 0xFFFF /* DSP2RX_EQ_B4_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_A_SHIFT 0 /* DSP2RX_EQ_B4_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_A_WIDTH 16 /* DSP2RX_EQ_B4_A - [15:0] */
-
-/*
- * R1422 (0x58E) - DSP2 RX EQ Band 4 B
- */
-#define WM8915_DSP2RX_EQ_B4_B_MASK 0xFFFF /* DSP2RX_EQ_B4_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_B_SHIFT 0 /* DSP2RX_EQ_B4_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_B_WIDTH 16 /* DSP2RX_EQ_B4_B - [15:0] */
-
-/*
- * R1423 (0x58F) - DSP2 RX EQ Band 4 C
- */
-#define WM8915_DSP2RX_EQ_B4_C_MASK 0xFFFF /* DSP2RX_EQ_B4_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_C_SHIFT 0 /* DSP2RX_EQ_B4_C - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_C_WIDTH 16 /* DSP2RX_EQ_B4_C - [15:0] */
-
-/*
- * R1424 (0x590) - DSP2 RX EQ Band 4 PG
- */
-#define WM8915_DSP2RX_EQ_B4_PG_MASK 0xFFFF /* DSP2RX_EQ_B4_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_PG_SHIFT 0 /* DSP2RX_EQ_B4_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B4_PG_WIDTH 16 /* DSP2RX_EQ_B4_PG - [15:0] */
-
-/*
- * R1425 (0x591) - DSP2 RX EQ Band 5 A
- */
-#define WM8915_DSP2RX_EQ_B5_A_MASK 0xFFFF /* DSP2RX_EQ_B5_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_A_SHIFT 0 /* DSP2RX_EQ_B5_A - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_A_WIDTH 16 /* DSP2RX_EQ_B5_A - [15:0] */
-
-/*
- * R1426 (0x592) - DSP2 RX EQ Band 5 B
- */
-#define WM8915_DSP2RX_EQ_B5_B_MASK 0xFFFF /* DSP2RX_EQ_B5_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_B_SHIFT 0 /* DSP2RX_EQ_B5_B - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_B_WIDTH 16 /* DSP2RX_EQ_B5_B - [15:0] */
-
-/*
- * R1427 (0x593) - DSP2 RX EQ Band 5 PG
- */
-#define WM8915_DSP2RX_EQ_B5_PG_MASK 0xFFFF /* DSP2RX_EQ_B5_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_PG_SHIFT 0 /* DSP2RX_EQ_B5_PG - [15:0] */
-#define WM8915_DSP2RX_EQ_B5_PG_WIDTH 16 /* DSP2RX_EQ_B5_PG - [15:0] */
-
-/*
- * R1536 (0x600) - DAC1 Mixer Volumes
- */
-#define WM8915_ADCR_DAC1_VOL_MASK 0x03E0 /* ADCR_DAC1_VOL - [9:5] */
-#define WM8915_ADCR_DAC1_VOL_SHIFT 5 /* ADCR_DAC1_VOL - [9:5] */
-#define WM8915_ADCR_DAC1_VOL_WIDTH 5 /* ADCR_DAC1_VOL - [9:5] */
-#define WM8915_ADCL_DAC1_VOL_MASK 0x001F /* ADCL_DAC1_VOL - [4:0] */
-#define WM8915_ADCL_DAC1_VOL_SHIFT 0 /* ADCL_DAC1_VOL - [4:0] */
-#define WM8915_ADCL_DAC1_VOL_WIDTH 5 /* ADCL_DAC1_VOL - [4:0] */
-
-/*
- * R1537 (0x601) - DAC1 Left Mixer Routing
- */
-#define WM8915_ADCR_TO_DAC1L 0x0020 /* ADCR_TO_DAC1L */
-#define WM8915_ADCR_TO_DAC1L_MASK 0x0020 /* ADCR_TO_DAC1L */
-#define WM8915_ADCR_TO_DAC1L_SHIFT 5 /* ADCR_TO_DAC1L */
-#define WM8915_ADCR_TO_DAC1L_WIDTH 1 /* ADCR_TO_DAC1L */
-#define WM8915_ADCL_TO_DAC1L 0x0010 /* ADCL_TO_DAC1L */
-#define WM8915_ADCL_TO_DAC1L_MASK 0x0010 /* ADCL_TO_DAC1L */
-#define WM8915_ADCL_TO_DAC1L_SHIFT 4 /* ADCL_TO_DAC1L */
-#define WM8915_ADCL_TO_DAC1L_WIDTH 1 /* ADCL_TO_DAC1L */
-#define WM8915_DSP2RXL_TO_DAC1L 0x0002 /* DSP2RXL_TO_DAC1L */
-#define WM8915_DSP2RXL_TO_DAC1L_MASK 0x0002 /* DSP2RXL_TO_DAC1L */
-#define WM8915_DSP2RXL_TO_DAC1L_SHIFT 1 /* DSP2RXL_TO_DAC1L */
-#define WM8915_DSP2RXL_TO_DAC1L_WIDTH 1 /* DSP2RXL_TO_DAC1L */
-#define WM8915_DSP1RXL_TO_DAC1L 0x0001 /* DSP1RXL_TO_DAC1L */
-#define WM8915_DSP1RXL_TO_DAC1L_MASK 0x0001 /* DSP1RXL_TO_DAC1L */
-#define WM8915_DSP1RXL_TO_DAC1L_SHIFT 0 /* DSP1RXL_TO_DAC1L */
-#define WM8915_DSP1RXL_TO_DAC1L_WIDTH 1 /* DSP1RXL_TO_DAC1L */
-
-/*
- * R1538 (0x602) - DAC1 Right Mixer Routing
- */
-#define WM8915_ADCR_TO_DAC1R 0x0020 /* ADCR_TO_DAC1R */
-#define WM8915_ADCR_TO_DAC1R_MASK 0x0020 /* ADCR_TO_DAC1R */
-#define WM8915_ADCR_TO_DAC1R_SHIFT 5 /* ADCR_TO_DAC1R */
-#define WM8915_ADCR_TO_DAC1R_WIDTH 1 /* ADCR_TO_DAC1R */
-#define WM8915_ADCL_TO_DAC1R 0x0010 /* ADCL_TO_DAC1R */
-#define WM8915_ADCL_TO_DAC1R_MASK 0x0010 /* ADCL_TO_DAC1R */
-#define WM8915_ADCL_TO_DAC1R_SHIFT 4 /* ADCL_TO_DAC1R */
-#define WM8915_ADCL_TO_DAC1R_WIDTH 1 /* ADCL_TO_DAC1R */
-#define WM8915_DSP2RXR_TO_DAC1R 0x0002 /* DSP2RXR_TO_DAC1R */
-#define WM8915_DSP2RXR_TO_DAC1R_MASK 0x0002 /* DSP2RXR_TO_DAC1R */
-#define WM8915_DSP2RXR_TO_DAC1R_SHIFT 1 /* DSP2RXR_TO_DAC1R */
-#define WM8915_DSP2RXR_TO_DAC1R_WIDTH 1 /* DSP2RXR_TO_DAC1R */
-#define WM8915_DSP1RXR_TO_DAC1R 0x0001 /* DSP1RXR_TO_DAC1R */
-#define WM8915_DSP1RXR_TO_DAC1R_MASK 0x0001 /* DSP1RXR_TO_DAC1R */
-#define WM8915_DSP1RXR_TO_DAC1R_SHIFT 0 /* DSP1RXR_TO_DAC1R */
-#define WM8915_DSP1RXR_TO_DAC1R_WIDTH 1 /* DSP1RXR_TO_DAC1R */
-
-/*
- * R1539 (0x603) - DAC2 Mixer Volumes
- */
-#define WM8915_ADCR_DAC2_VOL_MASK 0x03E0 /* ADCR_DAC2_VOL - [9:5] */
-#define WM8915_ADCR_DAC2_VOL_SHIFT 5 /* ADCR_DAC2_VOL - [9:5] */
-#define WM8915_ADCR_DAC2_VOL_WIDTH 5 /* ADCR_DAC2_VOL - [9:5] */
-#define WM8915_ADCL_DAC2_VOL_MASK 0x001F /* ADCL_DAC2_VOL - [4:0] */
-#define WM8915_ADCL_DAC2_VOL_SHIFT 0 /* ADCL_DAC2_VOL - [4:0] */
-#define WM8915_ADCL_DAC2_VOL_WIDTH 5 /* ADCL_DAC2_VOL - [4:0] */
-
-/*
- * R1540 (0x604) - DAC2 Left Mixer Routing
- */
-#define WM8915_ADCR_TO_DAC2L 0x0020 /* ADCR_TO_DAC2L */
-#define WM8915_ADCR_TO_DAC2L_MASK 0x0020 /* ADCR_TO_DAC2L */
-#define WM8915_ADCR_TO_DAC2L_SHIFT 5 /* ADCR_TO_DAC2L */
-#define WM8915_ADCR_TO_DAC2L_WIDTH 1 /* ADCR_TO_DAC2L */
-#define WM8915_ADCL_TO_DAC2L 0x0010 /* ADCL_TO_DAC2L */
-#define WM8915_ADCL_TO_DAC2L_MASK 0x0010 /* ADCL_TO_DAC2L */
-#define WM8915_ADCL_TO_DAC2L_SHIFT 4 /* ADCL_TO_DAC2L */
-#define WM8915_ADCL_TO_DAC2L_WIDTH 1 /* ADCL_TO_DAC2L */
-#define WM8915_DSP2RXL_TO_DAC2L 0x0002 /* DSP2RXL_TO_DAC2L */
-#define WM8915_DSP2RXL_TO_DAC2L_MASK 0x0002 /* DSP2RXL_TO_DAC2L */
-#define WM8915_DSP2RXL_TO_DAC2L_SHIFT 1 /* DSP2RXL_TO_DAC2L */
-#define WM8915_DSP2RXL_TO_DAC2L_WIDTH 1 /* DSP2RXL_TO_DAC2L */
-#define WM8915_DSP1RXL_TO_DAC2L 0x0001 /* DSP1RXL_TO_DAC2L */
-#define WM8915_DSP1RXL_TO_DAC2L_MASK 0x0001 /* DSP1RXL_TO_DAC2L */
-#define WM8915_DSP1RXL_TO_DAC2L_SHIFT 0 /* DSP1RXL_TO_DAC2L */
-#define WM8915_DSP1RXL_TO_DAC2L_WIDTH 1 /* DSP1RXL_TO_DAC2L */
-
-/*
- * R1541 (0x605) - DAC2 Right Mixer Routing
- */
-#define WM8915_ADCR_TO_DAC2R 0x0020 /* ADCR_TO_DAC2R */
-#define WM8915_ADCR_TO_DAC2R_MASK 0x0020 /* ADCR_TO_DAC2R */
-#define WM8915_ADCR_TO_DAC2R_SHIFT 5 /* ADCR_TO_DAC2R */
-#define WM8915_ADCR_TO_DAC2R_WIDTH 1 /* ADCR_TO_DAC2R */
-#define WM8915_ADCL_TO_DAC2R 0x0010 /* ADCL_TO_DAC2R */
-#define WM8915_ADCL_TO_DAC2R_MASK 0x0010 /* ADCL_TO_DAC2R */
-#define WM8915_ADCL_TO_DAC2R_SHIFT 4 /* ADCL_TO_DAC2R */
-#define WM8915_ADCL_TO_DAC2R_WIDTH 1 /* ADCL_TO_DAC2R */
-#define WM8915_DSP2RXR_TO_DAC2R 0x0002 /* DSP2RXR_TO_DAC2R */
-#define WM8915_DSP2RXR_TO_DAC2R_MASK 0x0002 /* DSP2RXR_TO_DAC2R */
-#define WM8915_DSP2RXR_TO_DAC2R_SHIFT 1 /* DSP2RXR_TO_DAC2R */
-#define WM8915_DSP2RXR_TO_DAC2R_WIDTH 1 /* DSP2RXR_TO_DAC2R */
-#define WM8915_DSP1RXR_TO_DAC2R 0x0001 /* DSP1RXR_TO_DAC2R */
-#define WM8915_DSP1RXR_TO_DAC2R_MASK 0x0001 /* DSP1RXR_TO_DAC2R */
-#define WM8915_DSP1RXR_TO_DAC2R_SHIFT 0 /* DSP1RXR_TO_DAC2R */
-#define WM8915_DSP1RXR_TO_DAC2R_WIDTH 1 /* DSP1RXR_TO_DAC2R */
-
-/*
- * R1542 (0x606) - DSP1 TX Left Mixer Routing
- */
-#define WM8915_ADC1L_TO_DSP1TXL 0x0002 /* ADC1L_TO_DSP1TXL */
-#define WM8915_ADC1L_TO_DSP1TXL_MASK 0x0002 /* ADC1L_TO_DSP1TXL */
-#define WM8915_ADC1L_TO_DSP1TXL_SHIFT 1 /* ADC1L_TO_DSP1TXL */
-#define WM8915_ADC1L_TO_DSP1TXL_WIDTH 1 /* ADC1L_TO_DSP1TXL */
-#define WM8915_DACL_TO_DSP1TXL 0x0001 /* DACL_TO_DSP1TXL */
-#define WM8915_DACL_TO_DSP1TXL_MASK 0x0001 /* DACL_TO_DSP1TXL */
-#define WM8915_DACL_TO_DSP1TXL_SHIFT 0 /* DACL_TO_DSP1TXL */
-#define WM8915_DACL_TO_DSP1TXL_WIDTH 1 /* DACL_TO_DSP1TXL */
-
-/*
- * R1543 (0x607) - DSP1 TX Right Mixer Routing
- */
-#define WM8915_ADC1R_TO_DSP1TXR 0x0002 /* ADC1R_TO_DSP1TXR */
-#define WM8915_ADC1R_TO_DSP1TXR_MASK 0x0002 /* ADC1R_TO_DSP1TXR */
-#define WM8915_ADC1R_TO_DSP1TXR_SHIFT 1 /* ADC1R_TO_DSP1TXR */
-#define WM8915_ADC1R_TO_DSP1TXR_WIDTH 1 /* ADC1R_TO_DSP1TXR */
-#define WM8915_DACR_TO_DSP1TXR 0x0001 /* DACR_TO_DSP1TXR */
-#define WM8915_DACR_TO_DSP1TXR_MASK 0x0001 /* DACR_TO_DSP1TXR */
-#define WM8915_DACR_TO_DSP1TXR_SHIFT 0 /* DACR_TO_DSP1TXR */
-#define WM8915_DACR_TO_DSP1TXR_WIDTH 1 /* DACR_TO_DSP1TXR */
-
-/*
- * R1544 (0x608) - DSP2 TX Left Mixer Routing
- */
-#define WM8915_ADC2L_TO_DSP2TXL 0x0002 /* ADC2L_TO_DSP2TXL */
-#define WM8915_ADC2L_TO_DSP2TXL_MASK 0x0002 /* ADC2L_TO_DSP2TXL */
-#define WM8915_ADC2L_TO_DSP2TXL_SHIFT 1 /* ADC2L_TO_DSP2TXL */
-#define WM8915_ADC2L_TO_DSP2TXL_WIDTH 1 /* ADC2L_TO_DSP2TXL */
-#define WM8915_DACL_TO_DSP2TXL 0x0001 /* DACL_TO_DSP2TXL */
-#define WM8915_DACL_TO_DSP2TXL_MASK 0x0001 /* DACL_TO_DSP2TXL */
-#define WM8915_DACL_TO_DSP2TXL_SHIFT 0 /* DACL_TO_DSP2TXL */
-#define WM8915_DACL_TO_DSP2TXL_WIDTH 1 /* DACL_TO_DSP2TXL */
-
-/*
- * R1545 (0x609) - DSP2 TX Right Mixer Routing
- */
-#define WM8915_ADC2R_TO_DSP2TXR 0x0002 /* ADC2R_TO_DSP2TXR */
-#define WM8915_ADC2R_TO_DSP2TXR_MASK 0x0002 /* ADC2R_TO_DSP2TXR */
-#define WM8915_ADC2R_TO_DSP2TXR_SHIFT 1 /* ADC2R_TO_DSP2TXR */
-#define WM8915_ADC2R_TO_DSP2TXR_WIDTH 1 /* ADC2R_TO_DSP2TXR */
-#define WM8915_DACR_TO_DSP2TXR 0x0001 /* DACR_TO_DSP2TXR */
-#define WM8915_DACR_TO_DSP2TXR_MASK 0x0001 /* DACR_TO_DSP2TXR */
-#define WM8915_DACR_TO_DSP2TXR_SHIFT 0 /* DACR_TO_DSP2TXR */
-#define WM8915_DACR_TO_DSP2TXR_WIDTH 1 /* DACR_TO_DSP2TXR */
-
-/*
- * R1546 (0x60A) - DSP TX Mixer Select
- */
-#define WM8915_DAC_TO_DSPTX_SRC 0x0001 /* DAC_TO_DSPTX_SRC */
-#define WM8915_DAC_TO_DSPTX_SRC_MASK 0x0001 /* DAC_TO_DSPTX_SRC */
-#define WM8915_DAC_TO_DSPTX_SRC_SHIFT 0 /* DAC_TO_DSPTX_SRC */
-#define WM8915_DAC_TO_DSPTX_SRC_WIDTH 1 /* DAC_TO_DSPTX_SRC */
-
-/*
- * R1552 (0x610) - DAC Softmute
- */
-#define WM8915_DAC_SOFTMUTEMODE 0x0002 /* DAC_SOFTMUTEMODE */
-#define WM8915_DAC_SOFTMUTEMODE_MASK 0x0002 /* DAC_SOFTMUTEMODE */
-#define WM8915_DAC_SOFTMUTEMODE_SHIFT 1 /* DAC_SOFTMUTEMODE */
-#define WM8915_DAC_SOFTMUTEMODE_WIDTH 1 /* DAC_SOFTMUTEMODE */
-#define WM8915_DAC_MUTERATE 0x0001 /* DAC_MUTERATE */
-#define WM8915_DAC_MUTERATE_MASK 0x0001 /* DAC_MUTERATE */
-#define WM8915_DAC_MUTERATE_SHIFT 0 /* DAC_MUTERATE */
-#define WM8915_DAC_MUTERATE_WIDTH 1 /* DAC_MUTERATE */
-
-/*
- * R1568 (0x620) - Oversampling
- */
-#define WM8915_SPK_OSR128 0x0008 /* SPK_OSR128 */
-#define WM8915_SPK_OSR128_MASK 0x0008 /* SPK_OSR128 */
-#define WM8915_SPK_OSR128_SHIFT 3 /* SPK_OSR128 */
-#define WM8915_SPK_OSR128_WIDTH 1 /* SPK_OSR128 */
-#define WM8915_DMIC_OSR64 0x0004 /* DMIC_OSR64 */
-#define WM8915_DMIC_OSR64_MASK 0x0004 /* DMIC_OSR64 */
-#define WM8915_DMIC_OSR64_SHIFT 2 /* DMIC_OSR64 */
-#define WM8915_DMIC_OSR64_WIDTH 1 /* DMIC_OSR64 */
-#define WM8915_ADC_OSR128 0x0002 /* ADC_OSR128 */
-#define WM8915_ADC_OSR128_MASK 0x0002 /* ADC_OSR128 */
-#define WM8915_ADC_OSR128_SHIFT 1 /* ADC_OSR128 */
-#define WM8915_ADC_OSR128_WIDTH 1 /* ADC_OSR128 */
-#define WM8915_DAC_OSR128 0x0001 /* DAC_OSR128 */
-#define WM8915_DAC_OSR128_MASK 0x0001 /* DAC_OSR128 */
-#define WM8915_DAC_OSR128_SHIFT 0 /* DAC_OSR128 */
-#define WM8915_DAC_OSR128_WIDTH 1 /* DAC_OSR128 */
-
-/*
- * R1569 (0x621) - Sidetone
- */
-#define WM8915_ST_LPF 0x1000 /* ST_LPF */
-#define WM8915_ST_LPF_MASK 0x1000 /* ST_LPF */
-#define WM8915_ST_LPF_SHIFT 12 /* ST_LPF */
-#define WM8915_ST_LPF_WIDTH 1 /* ST_LPF */
-#define WM8915_ST_HPF_CUT_MASK 0x0380 /* ST_HPF_CUT - [9:7] */
-#define WM8915_ST_HPF_CUT_SHIFT 7 /* ST_HPF_CUT - [9:7] */
-#define WM8915_ST_HPF_CUT_WIDTH 3 /* ST_HPF_CUT - [9:7] */
-#define WM8915_ST_HPF 0x0040 /* ST_HPF */
-#define WM8915_ST_HPF_MASK 0x0040 /* ST_HPF */
-#define WM8915_ST_HPF_SHIFT 6 /* ST_HPF */
-#define WM8915_ST_HPF_WIDTH 1 /* ST_HPF */
-#define WM8915_STR_SEL 0x0002 /* STR_SEL */
-#define WM8915_STR_SEL_MASK 0x0002 /* STR_SEL */
-#define WM8915_STR_SEL_SHIFT 1 /* STR_SEL */
-#define WM8915_STR_SEL_WIDTH 1 /* STR_SEL */
-#define WM8915_STL_SEL 0x0001 /* STL_SEL */
-#define WM8915_STL_SEL_MASK 0x0001 /* STL_SEL */
-#define WM8915_STL_SEL_SHIFT 0 /* STL_SEL */
-#define WM8915_STL_SEL_WIDTH 1 /* STL_SEL */
-
-/*
- * R1792 (0x700) - GPIO 1
- */
-#define WM8915_GP1_DIR 0x8000 /* GP1_DIR */
-#define WM8915_GP1_DIR_MASK 0x8000 /* GP1_DIR */
-#define WM8915_GP1_DIR_SHIFT 15 /* GP1_DIR */
-#define WM8915_GP1_DIR_WIDTH 1 /* GP1_DIR */
-#define WM8915_GP1_PU 0x4000 /* GP1_PU */
-#define WM8915_GP1_PU_MASK 0x4000 /* GP1_PU */
-#define WM8915_GP1_PU_SHIFT 14 /* GP1_PU */
-#define WM8915_GP1_PU_WIDTH 1 /* GP1_PU */
-#define WM8915_GP1_PD 0x2000 /* GP1_PD */
-#define WM8915_GP1_PD_MASK 0x2000 /* GP1_PD */
-#define WM8915_GP1_PD_SHIFT 13 /* GP1_PD */
-#define WM8915_GP1_PD_WIDTH 1 /* GP1_PD */
-#define WM8915_GP1_POL 0x0400 /* GP1_POL */
-#define WM8915_GP1_POL_MASK 0x0400 /* GP1_POL */
-#define WM8915_GP1_POL_SHIFT 10 /* GP1_POL */
-#define WM8915_GP1_POL_WIDTH 1 /* GP1_POL */
-#define WM8915_GP1_OP_CFG 0x0200 /* GP1_OP_CFG */
-#define WM8915_GP1_OP_CFG_MASK 0x0200 /* GP1_OP_CFG */
-#define WM8915_GP1_OP_CFG_SHIFT 9 /* GP1_OP_CFG */
-#define WM8915_GP1_OP_CFG_WIDTH 1 /* GP1_OP_CFG */
-#define WM8915_GP1_DB 0x0100 /* GP1_DB */
-#define WM8915_GP1_DB_MASK 0x0100 /* GP1_DB */
-#define WM8915_GP1_DB_SHIFT 8 /* GP1_DB */
-#define WM8915_GP1_DB_WIDTH 1 /* GP1_DB */
-#define WM8915_GP1_LVL 0x0040 /* GP1_LVL */
-#define WM8915_GP1_LVL_MASK 0x0040 /* GP1_LVL */
-#define WM8915_GP1_LVL_SHIFT 6 /* GP1_LVL */
-#define WM8915_GP1_LVL_WIDTH 1 /* GP1_LVL */
-#define WM8915_GP1_FN_MASK 0x000F /* GP1_FN - [3:0] */
-#define WM8915_GP1_FN_SHIFT 0 /* GP1_FN - [3:0] */
-#define WM8915_GP1_FN_WIDTH 4 /* GP1_FN - [3:0] */
-
-/*
- * R1793 (0x701) - GPIO 2
- */
-#define WM8915_GP2_DIR 0x8000 /* GP2_DIR */
-#define WM8915_GP2_DIR_MASK 0x8000 /* GP2_DIR */
-#define WM8915_GP2_DIR_SHIFT 15 /* GP2_DIR */
-#define WM8915_GP2_DIR_WIDTH 1 /* GP2_DIR */
-#define WM8915_GP2_PU 0x4000 /* GP2_PU */
-#define WM8915_GP2_PU_MASK 0x4000 /* GP2_PU */
-#define WM8915_GP2_PU_SHIFT 14 /* GP2_PU */
-#define WM8915_GP2_PU_WIDTH 1 /* GP2_PU */
-#define WM8915_GP2_PD 0x2000 /* GP2_PD */
-#define WM8915_GP2_PD_MASK 0x2000 /* GP2_PD */
-#define WM8915_GP2_PD_SHIFT 13 /* GP2_PD */
-#define WM8915_GP2_PD_WIDTH 1 /* GP2_PD */
-#define WM8915_GP2_POL 0x0400 /* GP2_POL */
-#define WM8915_GP2_POL_MASK 0x0400 /* GP2_POL */
-#define WM8915_GP2_POL_SHIFT 10 /* GP2_POL */
-#define WM8915_GP2_POL_WIDTH 1 /* GP2_POL */
-#define WM8915_GP2_OP_CFG 0x0200 /* GP2_OP_CFG */
-#define WM8915_GP2_OP_CFG_MASK 0x0200 /* GP2_OP_CFG */
-#define WM8915_GP2_OP_CFG_SHIFT 9 /* GP2_OP_CFG */
-#define WM8915_GP2_OP_CFG_WIDTH 1 /* GP2_OP_CFG */
-#define WM8915_GP2_DB 0x0100 /* GP2_DB */
-#define WM8915_GP2_DB_MASK 0x0100 /* GP2_DB */
-#define WM8915_GP2_DB_SHIFT 8 /* GP2_DB */
-#define WM8915_GP2_DB_WIDTH 1 /* GP2_DB */
-#define WM8915_GP2_LVL 0x0040 /* GP2_LVL */
-#define WM8915_GP2_LVL_MASK 0x0040 /* GP2_LVL */
-#define WM8915_GP2_LVL_SHIFT 6 /* GP2_LVL */
-#define WM8915_GP2_LVL_WIDTH 1 /* GP2_LVL */
-#define WM8915_GP2_FN_MASK 0x000F /* GP2_FN - [3:0] */
-#define WM8915_GP2_FN_SHIFT 0 /* GP2_FN - [3:0] */
-#define WM8915_GP2_FN_WIDTH 4 /* GP2_FN - [3:0] */
-
-/*
- * R1794 (0x702) - GPIO 3
- */
-#define WM8915_GP3_DIR 0x8000 /* GP3_DIR */
-#define WM8915_GP3_DIR_MASK 0x8000 /* GP3_DIR */
-#define WM8915_GP3_DIR_SHIFT 15 /* GP3_DIR */
-#define WM8915_GP3_DIR_WIDTH 1 /* GP3_DIR */
-#define WM8915_GP3_PU 0x4000 /* GP3_PU */
-#define WM8915_GP3_PU_MASK 0x4000 /* GP3_PU */
-#define WM8915_GP3_PU_SHIFT 14 /* GP3_PU */
-#define WM8915_GP3_PU_WIDTH 1 /* GP3_PU */
-#define WM8915_GP3_PD 0x2000 /* GP3_PD */
-#define WM8915_GP3_PD_MASK 0x2000 /* GP3_PD */
-#define WM8915_GP3_PD_SHIFT 13 /* GP3_PD */
-#define WM8915_GP3_PD_WIDTH 1 /* GP3_PD */
-#define WM8915_GP3_POL 0x0400 /* GP3_POL */
-#define WM8915_GP3_POL_MASK 0x0400 /* GP3_POL */
-#define WM8915_GP3_POL_SHIFT 10 /* GP3_POL */
-#define WM8915_GP3_POL_WIDTH 1 /* GP3_POL */
-#define WM8915_GP3_OP_CFG 0x0200 /* GP3_OP_CFG */
-#define WM8915_GP3_OP_CFG_MASK 0x0200 /* GP3_OP_CFG */
-#define WM8915_GP3_OP_CFG_SHIFT 9 /* GP3_OP_CFG */
-#define WM8915_GP3_OP_CFG_WIDTH 1 /* GP3_OP_CFG */
-#define WM8915_GP3_DB 0x0100 /* GP3_DB */
-#define WM8915_GP3_DB_MASK 0x0100 /* GP3_DB */
-#define WM8915_GP3_DB_SHIFT 8 /* GP3_DB */
-#define WM8915_GP3_DB_WIDTH 1 /* GP3_DB */
-#define WM8915_GP3_LVL 0x0040 /* GP3_LVL */
-#define WM8915_GP3_LVL_MASK 0x0040 /* GP3_LVL */
-#define WM8915_GP3_LVL_SHIFT 6 /* GP3_LVL */
-#define WM8915_GP3_LVL_WIDTH 1 /* GP3_LVL */
-#define WM8915_GP3_FN_MASK 0x000F /* GP3_FN - [3:0] */
-#define WM8915_GP3_FN_SHIFT 0 /* GP3_FN - [3:0] */
-#define WM8915_GP3_FN_WIDTH 4 /* GP3_FN - [3:0] */
-
-/*
- * R1795 (0x703) - GPIO 4
- */
-#define WM8915_GP4_DIR 0x8000 /* GP4_DIR */
-#define WM8915_GP4_DIR_MASK 0x8000 /* GP4_DIR */
-#define WM8915_GP4_DIR_SHIFT 15 /* GP4_DIR */
-#define WM8915_GP4_DIR_WIDTH 1 /* GP4_DIR */
-#define WM8915_GP4_PU 0x4000 /* GP4_PU */
-#define WM8915_GP4_PU_MASK 0x4000 /* GP4_PU */
-#define WM8915_GP4_PU_SHIFT 14 /* GP4_PU */
-#define WM8915_GP4_PU_WIDTH 1 /* GP4_PU */
-#define WM8915_GP4_PD 0x2000 /* GP4_PD */
-#define WM8915_GP4_PD_MASK 0x2000 /* GP4_PD */
-#define WM8915_GP4_PD_SHIFT 13 /* GP4_PD */
-#define WM8915_GP4_PD_WIDTH 1 /* GP4_PD */
-#define WM8915_GP4_POL 0x0400 /* GP4_POL */
-#define WM8915_GP4_POL_MASK 0x0400 /* GP4_POL */
-#define WM8915_GP4_POL_SHIFT 10 /* GP4_POL */
-#define WM8915_GP4_POL_WIDTH 1 /* GP4_POL */
-#define WM8915_GP4_OP_CFG 0x0200 /* GP4_OP_CFG */
-#define WM8915_GP4_OP_CFG_MASK 0x0200 /* GP4_OP_CFG */
-#define WM8915_GP4_OP_CFG_SHIFT 9 /* GP4_OP_CFG */
-#define WM8915_GP4_OP_CFG_WIDTH 1 /* GP4_OP_CFG */
-#define WM8915_GP4_DB 0x0100 /* GP4_DB */
-#define WM8915_GP4_DB_MASK 0x0100 /* GP4_DB */
-#define WM8915_GP4_DB_SHIFT 8 /* GP4_DB */
-#define WM8915_GP4_DB_WIDTH 1 /* GP4_DB */
-#define WM8915_GP4_LVL 0x0040 /* GP4_LVL */
-#define WM8915_GP4_LVL_MASK 0x0040 /* GP4_LVL */
-#define WM8915_GP4_LVL_SHIFT 6 /* GP4_LVL */
-#define WM8915_GP4_LVL_WIDTH 1 /* GP4_LVL */
-#define WM8915_GP4_FN_MASK 0x000F /* GP4_FN - [3:0] */
-#define WM8915_GP4_FN_SHIFT 0 /* GP4_FN - [3:0] */
-#define WM8915_GP4_FN_WIDTH 4 /* GP4_FN - [3:0] */
-
-/*
- * R1796 (0x704) - GPIO 5
- */
-#define WM8915_GP5_DIR 0x8000 /* GP5_DIR */
-#define WM8915_GP5_DIR_MASK 0x8000 /* GP5_DIR */
-#define WM8915_GP5_DIR_SHIFT 15 /* GP5_DIR */
-#define WM8915_GP5_DIR_WIDTH 1 /* GP5_DIR */
-#define WM8915_GP5_PU 0x4000 /* GP5_PU */
-#define WM8915_GP5_PU_MASK 0x4000 /* GP5_PU */
-#define WM8915_GP5_PU_SHIFT 14 /* GP5_PU */
-#define WM8915_GP5_PU_WIDTH 1 /* GP5_PU */
-#define WM8915_GP5_PD 0x2000 /* GP5_PD */
-#define WM8915_GP5_PD_MASK 0x2000 /* GP5_PD */
-#define WM8915_GP5_PD_SHIFT 13 /* GP5_PD */
-#define WM8915_GP5_PD_WIDTH 1 /* GP5_PD */
-#define WM8915_GP5_POL 0x0400 /* GP5_POL */
-#define WM8915_GP5_POL_MASK 0x0400 /* GP5_POL */
-#define WM8915_GP5_POL_SHIFT 10 /* GP5_POL */
-#define WM8915_GP5_POL_WIDTH 1 /* GP5_POL */
-#define WM8915_GP5_OP_CFG 0x0200 /* GP5_OP_CFG */
-#define WM8915_GP5_OP_CFG_MASK 0x0200 /* GP5_OP_CFG */
-#define WM8915_GP5_OP_CFG_SHIFT 9 /* GP5_OP_CFG */
-#define WM8915_GP5_OP_CFG_WIDTH 1 /* GP5_OP_CFG */
-#define WM8915_GP5_DB 0x0100 /* GP5_DB */
-#define WM8915_GP5_DB_MASK 0x0100 /* GP5_DB */
-#define WM8915_GP5_DB_SHIFT 8 /* GP5_DB */
-#define WM8915_GP5_DB_WIDTH 1 /* GP5_DB */
-#define WM8915_GP5_LVL 0x0040 /* GP5_LVL */
-#define WM8915_GP5_LVL_MASK 0x0040 /* GP5_LVL */
-#define WM8915_GP5_LVL_SHIFT 6 /* GP5_LVL */
-#define WM8915_GP5_LVL_WIDTH 1 /* GP5_LVL */
-#define WM8915_GP5_FN_MASK 0x000F /* GP5_FN - [3:0] */
-#define WM8915_GP5_FN_SHIFT 0 /* GP5_FN - [3:0] */
-#define WM8915_GP5_FN_WIDTH 4 /* GP5_FN - [3:0] */
-
-/*
- * R1824 (0x720) - Pull Control (1)
- */
-#define WM8915_DMICDAT2_PD 0x1000 /* DMICDAT2_PD */
-#define WM8915_DMICDAT2_PD_MASK 0x1000 /* DMICDAT2_PD */
-#define WM8915_DMICDAT2_PD_SHIFT 12 /* DMICDAT2_PD */
-#define WM8915_DMICDAT2_PD_WIDTH 1 /* DMICDAT2_PD */
-#define WM8915_DMICDAT1_PD 0x0400 /* DMICDAT1_PD */
-#define WM8915_DMICDAT1_PD_MASK 0x0400 /* DMICDAT1_PD */
-#define WM8915_DMICDAT1_PD_SHIFT 10 /* DMICDAT1_PD */
-#define WM8915_DMICDAT1_PD_WIDTH 1 /* DMICDAT1_PD */
-#define WM8915_MCLK2_PU 0x0200 /* MCLK2_PU */
-#define WM8915_MCLK2_PU_MASK 0x0200 /* MCLK2_PU */
-#define WM8915_MCLK2_PU_SHIFT 9 /* MCLK2_PU */
-#define WM8915_MCLK2_PU_WIDTH 1 /* MCLK2_PU */
-#define WM8915_MCLK2_PD 0x0100 /* MCLK2_PD */
-#define WM8915_MCLK2_PD_MASK 0x0100 /* MCLK2_PD */
-#define WM8915_MCLK2_PD_SHIFT 8 /* MCLK2_PD */
-#define WM8915_MCLK2_PD_WIDTH 1 /* MCLK2_PD */
-#define WM8915_MCLK1_PU 0x0080 /* MCLK1_PU */
-#define WM8915_MCLK1_PU_MASK 0x0080 /* MCLK1_PU */
-#define WM8915_MCLK1_PU_SHIFT 7 /* MCLK1_PU */
-#define WM8915_MCLK1_PU_WIDTH 1 /* MCLK1_PU */
-#define WM8915_MCLK1_PD 0x0040 /* MCLK1_PD */
-#define WM8915_MCLK1_PD_MASK 0x0040 /* MCLK1_PD */
-#define WM8915_MCLK1_PD_SHIFT 6 /* MCLK1_PD */
-#define WM8915_MCLK1_PD_WIDTH 1 /* MCLK1_PD */
-#define WM8915_DACDAT1_PU 0x0020 /* DACDAT1_PU */
-#define WM8915_DACDAT1_PU_MASK 0x0020 /* DACDAT1_PU */
-#define WM8915_DACDAT1_PU_SHIFT 5 /* DACDAT1_PU */
-#define WM8915_DACDAT1_PU_WIDTH 1 /* DACDAT1_PU */
-#define WM8915_DACDAT1_PD 0x0010 /* DACDAT1_PD */
-#define WM8915_DACDAT1_PD_MASK 0x0010 /* DACDAT1_PD */
-#define WM8915_DACDAT1_PD_SHIFT 4 /* DACDAT1_PD */
-#define WM8915_DACDAT1_PD_WIDTH 1 /* DACDAT1_PD */
-#define WM8915_DACLRCLK1_PU 0x0008 /* DACLRCLK1_PU */
-#define WM8915_DACLRCLK1_PU_MASK 0x0008 /* DACLRCLK1_PU */
-#define WM8915_DACLRCLK1_PU_SHIFT 3 /* DACLRCLK1_PU */
-#define WM8915_DACLRCLK1_PU_WIDTH 1 /* DACLRCLK1_PU */
-#define WM8915_DACLRCLK1_PD 0x0004 /* DACLRCLK1_PD */
-#define WM8915_DACLRCLK1_PD_MASK 0x0004 /* DACLRCLK1_PD */
-#define WM8915_DACLRCLK1_PD_SHIFT 2 /* DACLRCLK1_PD */
-#define WM8915_DACLRCLK1_PD_WIDTH 1 /* DACLRCLK1_PD */
-#define WM8915_BCLK1_PU 0x0002 /* BCLK1_PU */
-#define WM8915_BCLK1_PU_MASK 0x0002 /* BCLK1_PU */
-#define WM8915_BCLK1_PU_SHIFT 1 /* BCLK1_PU */
-#define WM8915_BCLK1_PU_WIDTH 1 /* BCLK1_PU */
-#define WM8915_BCLK1_PD 0x0001 /* BCLK1_PD */
-#define WM8915_BCLK1_PD_MASK 0x0001 /* BCLK1_PD */
-#define WM8915_BCLK1_PD_SHIFT 0 /* BCLK1_PD */
-#define WM8915_BCLK1_PD_WIDTH 1 /* BCLK1_PD */
-
-/*
- * R1825 (0x721) - Pull Control (2)
- */
-#define WM8915_LDO1ENA_PD 0x0100 /* LDO1ENA_PD */
-#define WM8915_LDO1ENA_PD_MASK 0x0100 /* LDO1ENA_PD */
-#define WM8915_LDO1ENA_PD_SHIFT 8 /* LDO1ENA_PD */
-#define WM8915_LDO1ENA_PD_WIDTH 1 /* LDO1ENA_PD */
-#define WM8915_ADDR_PD 0x0040 /* ADDR_PD */
-#define WM8915_ADDR_PD_MASK 0x0040 /* ADDR_PD */
-#define WM8915_ADDR_PD_SHIFT 6 /* ADDR_PD */
-#define WM8915_ADDR_PD_WIDTH 1 /* ADDR_PD */
-#define WM8915_DACDAT2_PU 0x0020 /* DACDAT2_PU */
-#define WM8915_DACDAT2_PU_MASK 0x0020 /* DACDAT2_PU */
-#define WM8915_DACDAT2_PU_SHIFT 5 /* DACDAT2_PU */
-#define WM8915_DACDAT2_PU_WIDTH 1 /* DACDAT2_PU */
-#define WM8915_DACDAT2_PD 0x0010 /* DACDAT2_PD */
-#define WM8915_DACDAT2_PD_MASK 0x0010 /* DACDAT2_PD */
-#define WM8915_DACDAT2_PD_SHIFT 4 /* DACDAT2_PD */
-#define WM8915_DACDAT2_PD_WIDTH 1 /* DACDAT2_PD */
-#define WM8915_DACLRCLK2_PU 0x0008 /* DACLRCLK2_PU */
-#define WM8915_DACLRCLK2_PU_MASK 0x0008 /* DACLRCLK2_PU */
-#define WM8915_DACLRCLK2_PU_SHIFT 3 /* DACLRCLK2_PU */
-#define WM8915_DACLRCLK2_PU_WIDTH 1 /* DACLRCLK2_PU */
-#define WM8915_DACLRCLK2_PD 0x0004 /* DACLRCLK2_PD */
-#define WM8915_DACLRCLK2_PD_MASK 0x0004 /* DACLRCLK2_PD */
-#define WM8915_DACLRCLK2_PD_SHIFT 2 /* DACLRCLK2_PD */
-#define WM8915_DACLRCLK2_PD_WIDTH 1 /* DACLRCLK2_PD */
-#define WM8915_BCLK2_PU 0x0002 /* BCLK2_PU */
-#define WM8915_BCLK2_PU_MASK 0x0002 /* BCLK2_PU */
-#define WM8915_BCLK2_PU_SHIFT 1 /* BCLK2_PU */
-#define WM8915_BCLK2_PU_WIDTH 1 /* BCLK2_PU */
-#define WM8915_BCLK2_PD 0x0001 /* BCLK2_PD */
-#define WM8915_BCLK2_PD_MASK 0x0001 /* BCLK2_PD */
-#define WM8915_BCLK2_PD_SHIFT 0 /* BCLK2_PD */
-#define WM8915_BCLK2_PD_WIDTH 1 /* BCLK2_PD */
-
-/*
- * R1840 (0x730) - Interrupt Status 1
- */
-#define WM8915_GP5_EINT 0x0010 /* GP5_EINT */
-#define WM8915_GP5_EINT_MASK 0x0010 /* GP5_EINT */
-#define WM8915_GP5_EINT_SHIFT 4 /* GP5_EINT */
-#define WM8915_GP5_EINT_WIDTH 1 /* GP5_EINT */
-#define WM8915_GP4_EINT 0x0008 /* GP4_EINT */
-#define WM8915_GP4_EINT_MASK 0x0008 /* GP4_EINT */
-#define WM8915_GP4_EINT_SHIFT 3 /* GP4_EINT */
-#define WM8915_GP4_EINT_WIDTH 1 /* GP4_EINT */
-#define WM8915_GP3_EINT 0x0004 /* GP3_EINT */
-#define WM8915_GP3_EINT_MASK 0x0004 /* GP3_EINT */
-#define WM8915_GP3_EINT_SHIFT 2 /* GP3_EINT */
-#define WM8915_GP3_EINT_WIDTH 1 /* GP3_EINT */
-#define WM8915_GP2_EINT 0x0002 /* GP2_EINT */
-#define WM8915_GP2_EINT_MASK 0x0002 /* GP2_EINT */
-#define WM8915_GP2_EINT_SHIFT 1 /* GP2_EINT */
-#define WM8915_GP2_EINT_WIDTH 1 /* GP2_EINT */
-#define WM8915_GP1_EINT 0x0001 /* GP1_EINT */
-#define WM8915_GP1_EINT_MASK 0x0001 /* GP1_EINT */
-#define WM8915_GP1_EINT_SHIFT 0 /* GP1_EINT */
-#define WM8915_GP1_EINT_WIDTH 1 /* GP1_EINT */
-
-/*
- * R1841 (0x731) - Interrupt Status 2
- */
-#define WM8915_DCS_DONE_23_EINT 0x1000 /* DCS_DONE_23_EINT */
-#define WM8915_DCS_DONE_23_EINT_MASK 0x1000 /* DCS_DONE_23_EINT */
-#define WM8915_DCS_DONE_23_EINT_SHIFT 12 /* DCS_DONE_23_EINT */
-#define WM8915_DCS_DONE_23_EINT_WIDTH 1 /* DCS_DONE_23_EINT */
-#define WM8915_DCS_DONE_01_EINT 0x0800 /* DCS_DONE_01_EINT */
-#define WM8915_DCS_DONE_01_EINT_MASK 0x0800 /* DCS_DONE_01_EINT */
-#define WM8915_DCS_DONE_01_EINT_SHIFT 11 /* DCS_DONE_01_EINT */
-#define WM8915_DCS_DONE_01_EINT_WIDTH 1 /* DCS_DONE_01_EINT */
-#define WM8915_WSEQ_DONE_EINT 0x0400 /* WSEQ_DONE_EINT */
-#define WM8915_WSEQ_DONE_EINT_MASK 0x0400 /* WSEQ_DONE_EINT */
-#define WM8915_WSEQ_DONE_EINT_SHIFT 10 /* WSEQ_DONE_EINT */
-#define WM8915_WSEQ_DONE_EINT_WIDTH 1 /* WSEQ_DONE_EINT */
-#define WM8915_FIFOS_ERR_EINT 0x0200 /* FIFOS_ERR_EINT */
-#define WM8915_FIFOS_ERR_EINT_MASK 0x0200 /* FIFOS_ERR_EINT */
-#define WM8915_FIFOS_ERR_EINT_SHIFT 9 /* FIFOS_ERR_EINT */
-#define WM8915_FIFOS_ERR_EINT_WIDTH 1 /* FIFOS_ERR_EINT */
-#define WM8915_DSP2DRC_SIG_DET_EINT 0x0080 /* DSP2DRC_SIG_DET_EINT */
-#define WM8915_DSP2DRC_SIG_DET_EINT_MASK 0x0080 /* DSP2DRC_SIG_DET_EINT */
-#define WM8915_DSP2DRC_SIG_DET_EINT_SHIFT 7 /* DSP2DRC_SIG_DET_EINT */
-#define WM8915_DSP2DRC_SIG_DET_EINT_WIDTH 1 /* DSP2DRC_SIG_DET_EINT */
-#define WM8915_DSP1DRC_SIG_DET_EINT 0x0040 /* DSP1DRC_SIG_DET_EINT */
-#define WM8915_DSP1DRC_SIG_DET_EINT_MASK 0x0040 /* DSP1DRC_SIG_DET_EINT */
-#define WM8915_DSP1DRC_SIG_DET_EINT_SHIFT 6 /* DSP1DRC_SIG_DET_EINT */
-#define WM8915_DSP1DRC_SIG_DET_EINT_WIDTH 1 /* DSP1DRC_SIG_DET_EINT */
-#define WM8915_FLL_SW_CLK_DONE_EINT 0x0008 /* FLL_SW_CLK_DONE_EINT */
-#define WM8915_FLL_SW_CLK_DONE_EINT_MASK 0x0008 /* FLL_SW_CLK_DONE_EINT */
-#define WM8915_FLL_SW_CLK_DONE_EINT_SHIFT 3 /* FLL_SW_CLK_DONE_EINT */
-#define WM8915_FLL_SW_CLK_DONE_EINT_WIDTH 1 /* FLL_SW_CLK_DONE_EINT */
-#define WM8915_FLL_LOCK_EINT 0x0004 /* FLL_LOCK_EINT */
-#define WM8915_FLL_LOCK_EINT_MASK 0x0004 /* FLL_LOCK_EINT */
-#define WM8915_FLL_LOCK_EINT_SHIFT 2 /* FLL_LOCK_EINT */
-#define WM8915_FLL_LOCK_EINT_WIDTH 1 /* FLL_LOCK_EINT */
-#define WM8915_HP_DONE_EINT 0x0002 /* HP_DONE_EINT */
-#define WM8915_HP_DONE_EINT_MASK 0x0002 /* HP_DONE_EINT */
-#define WM8915_HP_DONE_EINT_SHIFT 1 /* HP_DONE_EINT */
-#define WM8915_HP_DONE_EINT_WIDTH 1 /* HP_DONE_EINT */
-#define WM8915_MICD_EINT 0x0001 /* MICD_EINT */
-#define WM8915_MICD_EINT_MASK 0x0001 /* MICD_EINT */
-#define WM8915_MICD_EINT_SHIFT 0 /* MICD_EINT */
-#define WM8915_MICD_EINT_WIDTH 1 /* MICD_EINT */
-
-/*
- * R1842 (0x732) - Interrupt Raw Status 2
- */
-#define WM8915_DCS_DONE_23_STS 0x1000 /* DCS_DONE_23_STS */
-#define WM8915_DCS_DONE_23_STS_MASK 0x1000 /* DCS_DONE_23_STS */
-#define WM8915_DCS_DONE_23_STS_SHIFT 12 /* DCS_DONE_23_STS */
-#define WM8915_DCS_DONE_23_STS_WIDTH 1 /* DCS_DONE_23_STS */
-#define WM8915_DCS_DONE_01_STS 0x0800 /* DCS_DONE_01_STS */
-#define WM8915_DCS_DONE_01_STS_MASK 0x0800 /* DCS_DONE_01_STS */
-#define WM8915_DCS_DONE_01_STS_SHIFT 11 /* DCS_DONE_01_STS */
-#define WM8915_DCS_DONE_01_STS_WIDTH 1 /* DCS_DONE_01_STS */
-#define WM8915_WSEQ_DONE_STS 0x0400 /* WSEQ_DONE_STS */
-#define WM8915_WSEQ_DONE_STS_MASK 0x0400 /* WSEQ_DONE_STS */
-#define WM8915_WSEQ_DONE_STS_SHIFT 10 /* WSEQ_DONE_STS */
-#define WM8915_WSEQ_DONE_STS_WIDTH 1 /* WSEQ_DONE_STS */
-#define WM8915_FIFOS_ERR_STS 0x0200 /* FIFOS_ERR_STS */
-#define WM8915_FIFOS_ERR_STS_MASK 0x0200 /* FIFOS_ERR_STS */
-#define WM8915_FIFOS_ERR_STS_SHIFT 9 /* FIFOS_ERR_STS */
-#define WM8915_FIFOS_ERR_STS_WIDTH 1 /* FIFOS_ERR_STS */
-#define WM8915_DSP2DRC_SIG_DET_STS 0x0080 /* DSP2DRC_SIG_DET_STS */
-#define WM8915_DSP2DRC_SIG_DET_STS_MASK 0x0080 /* DSP2DRC_SIG_DET_STS */
-#define WM8915_DSP2DRC_SIG_DET_STS_SHIFT 7 /* DSP2DRC_SIG_DET_STS */
-#define WM8915_DSP2DRC_SIG_DET_STS_WIDTH 1 /* DSP2DRC_SIG_DET_STS */
-#define WM8915_DSP1DRC_SIG_DET_STS 0x0040 /* DSP1DRC_SIG_DET_STS */
-#define WM8915_DSP1DRC_SIG_DET_STS_MASK 0x0040 /* DSP1DRC_SIG_DET_STS */
-#define WM8915_DSP1DRC_SIG_DET_STS_SHIFT 6 /* DSP1DRC_SIG_DET_STS */
-#define WM8915_DSP1DRC_SIG_DET_STS_WIDTH 1 /* DSP1DRC_SIG_DET_STS */
-#define WM8915_FLL_LOCK_STS 0x0004 /* FLL_LOCK_STS */
-#define WM8915_FLL_LOCK_STS_MASK 0x0004 /* FLL_LOCK_STS */
-#define WM8915_FLL_LOCK_STS_SHIFT 2 /* FLL_LOCK_STS */
-#define WM8915_FLL_LOCK_STS_WIDTH 1 /* FLL_LOCK_STS */
-
-/*
- * R1848 (0x738) - Interrupt Status 1 Mask
- */
-#define WM8915_IM_GP5_EINT 0x0010 /* IM_GP5_EINT */
-#define WM8915_IM_GP5_EINT_MASK 0x0010 /* IM_GP5_EINT */
-#define WM8915_IM_GP5_EINT_SHIFT 4 /* IM_GP5_EINT */
-#define WM8915_IM_GP5_EINT_WIDTH 1 /* IM_GP5_EINT */
-#define WM8915_IM_GP4_EINT 0x0008 /* IM_GP4_EINT */
-#define WM8915_IM_GP4_EINT_MASK 0x0008 /* IM_GP4_EINT */
-#define WM8915_IM_GP4_EINT_SHIFT 3 /* IM_GP4_EINT */
-#define WM8915_IM_GP4_EINT_WIDTH 1 /* IM_GP4_EINT */
-#define WM8915_IM_GP3_EINT 0x0004 /* IM_GP3_EINT */
-#define WM8915_IM_GP3_EINT_MASK 0x0004 /* IM_GP3_EINT */
-#define WM8915_IM_GP3_EINT_SHIFT 2 /* IM_GP3_EINT */
-#define WM8915_IM_GP3_EINT_WIDTH 1 /* IM_GP3_EINT */
-#define WM8915_IM_GP2_EINT 0x0002 /* IM_GP2_EINT */
-#define WM8915_IM_GP2_EINT_MASK 0x0002 /* IM_GP2_EINT */
-#define WM8915_IM_GP2_EINT_SHIFT 1 /* IM_GP2_EINT */
-#define WM8915_IM_GP2_EINT_WIDTH 1 /* IM_GP2_EINT */
-#define WM8915_IM_GP1_EINT 0x0001 /* IM_GP1_EINT */
-#define WM8915_IM_GP1_EINT_MASK 0x0001 /* IM_GP1_EINT */
-#define WM8915_IM_GP1_EINT_SHIFT 0 /* IM_GP1_EINT */
-#define WM8915_IM_GP1_EINT_WIDTH 1 /* IM_GP1_EINT */
-
-/*
- * R1849 (0x739) - Interrupt Status 2 Mask
- */
-#define WM8915_IM_DCS_DONE_23_EINT 0x1000 /* IM_DCS_DONE_23_EINT */
-#define WM8915_IM_DCS_DONE_23_EINT_MASK 0x1000 /* IM_DCS_DONE_23_EINT */
-#define WM8915_IM_DCS_DONE_23_EINT_SHIFT 12 /* IM_DCS_DONE_23_EINT */
-#define WM8915_IM_DCS_DONE_23_EINT_WIDTH 1 /* IM_DCS_DONE_23_EINT */
-#define WM8915_IM_DCS_DONE_01_EINT 0x0800 /* IM_DCS_DONE_01_EINT */
-#define WM8915_IM_DCS_DONE_01_EINT_MASK 0x0800 /* IM_DCS_DONE_01_EINT */
-#define WM8915_IM_DCS_DONE_01_EINT_SHIFT 11 /* IM_DCS_DONE_01_EINT */
-#define WM8915_IM_DCS_DONE_01_EINT_WIDTH 1 /* IM_DCS_DONE_01_EINT */
-#define WM8915_IM_WSEQ_DONE_EINT 0x0400 /* IM_WSEQ_DONE_EINT */
-#define WM8915_IM_WSEQ_DONE_EINT_MASK 0x0400 /* IM_WSEQ_DONE_EINT */
-#define WM8915_IM_WSEQ_DONE_EINT_SHIFT 10 /* IM_WSEQ_DONE_EINT */
-#define WM8915_IM_WSEQ_DONE_EINT_WIDTH 1 /* IM_WSEQ_DONE_EINT */
-#define WM8915_IM_FIFOS_ERR_EINT 0x0200 /* IM_FIFOS_ERR_EINT */
-#define WM8915_IM_FIFOS_ERR_EINT_MASK 0x0200 /* IM_FIFOS_ERR_EINT */
-#define WM8915_IM_FIFOS_ERR_EINT_SHIFT 9 /* IM_FIFOS_ERR_EINT */
-#define WM8915_IM_FIFOS_ERR_EINT_WIDTH 1 /* IM_FIFOS_ERR_EINT */
-#define WM8915_IM_DSP2DRC_SIG_DET_EINT 0x0080 /* IM_DSP2DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP2DRC_SIG_DET_EINT_MASK 0x0080 /* IM_DSP2DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP2DRC_SIG_DET_EINT_SHIFT 7 /* IM_DSP2DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP2DRC_SIG_DET_EINT_WIDTH 1 /* IM_DSP2DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP1DRC_SIG_DET_EINT 0x0040 /* IM_DSP1DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP1DRC_SIG_DET_EINT_MASK 0x0040 /* IM_DSP1DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP1DRC_SIG_DET_EINT_SHIFT 6 /* IM_DSP1DRC_SIG_DET_EINT */
-#define WM8915_IM_DSP1DRC_SIG_DET_EINT_WIDTH 1 /* IM_DSP1DRC_SIG_DET_EINT */
-#define WM8915_IM_FLL_SW_CLK_DONE_EINT 0x0008 /* IM_FLL_SW_CLK_DONE_EINT */
-#define WM8915_IM_FLL_SW_CLK_DONE_EINT_MASK 0x0008 /* IM_FLL_SW_CLK_DONE_EINT */
-#define WM8915_IM_FLL_SW_CLK_DONE_EINT_SHIFT 3 /* IM_FLL_SW_CLK_DONE_EINT */
-#define WM8915_IM_FLL_SW_CLK_DONE_EINT_WIDTH 1 /* IM_FLL_SW_CLK_DONE_EINT */
-#define WM8915_IM_FLL_LOCK_EINT 0x0004 /* IM_FLL_LOCK_EINT */
-#define WM8915_IM_FLL_LOCK_EINT_MASK 0x0004 /* IM_FLL_LOCK_EINT */
-#define WM8915_IM_FLL_LOCK_EINT_SHIFT 2 /* IM_FLL_LOCK_EINT */
-#define WM8915_IM_FLL_LOCK_EINT_WIDTH 1 /* IM_FLL_LOCK_EINT */
-#define WM8915_IM_HP_DONE_EINT 0x0002 /* IM_HP_DONE_EINT */
-#define WM8915_IM_HP_DONE_EINT_MASK 0x0002 /* IM_HP_DONE_EINT */
-#define WM8915_IM_HP_DONE_EINT_SHIFT 1 /* IM_HP_DONE_EINT */
-#define WM8915_IM_HP_DONE_EINT_WIDTH 1 /* IM_HP_DONE_EINT */
-#define WM8915_IM_MICD_EINT 0x0001 /* IM_MICD_EINT */
-#define WM8915_IM_MICD_EINT_MASK 0x0001 /* IM_MICD_EINT */
-#define WM8915_IM_MICD_EINT_SHIFT 0 /* IM_MICD_EINT */
-#define WM8915_IM_MICD_EINT_WIDTH 1 /* IM_MICD_EINT */
-
-/*
- * R1856 (0x740) - Interrupt Control
- */
-#define WM8915_IM_IRQ 0x0001 /* IM_IRQ */
-#define WM8915_IM_IRQ_MASK 0x0001 /* IM_IRQ */
-#define WM8915_IM_IRQ_SHIFT 0 /* IM_IRQ */
-#define WM8915_IM_IRQ_WIDTH 1 /* IM_IRQ */
-
-/*
- * R2048 (0x800) - Left PDM Speaker
- */
-#define WM8915_SPKL_ENA 0x0010 /* SPKL_ENA */
-#define WM8915_SPKL_ENA_MASK 0x0010 /* SPKL_ENA */
-#define WM8915_SPKL_ENA_SHIFT 4 /* SPKL_ENA */
-#define WM8915_SPKL_ENA_WIDTH 1 /* SPKL_ENA */
-#define WM8915_SPKL_MUTE 0x0008 /* SPKL_MUTE */
-#define WM8915_SPKL_MUTE_MASK 0x0008 /* SPKL_MUTE */
-#define WM8915_SPKL_MUTE_SHIFT 3 /* SPKL_MUTE */
-#define WM8915_SPKL_MUTE_WIDTH 1 /* SPKL_MUTE */
-#define WM8915_SPKL_MUTE_ZC 0x0004 /* SPKL_MUTE_ZC */
-#define WM8915_SPKL_MUTE_ZC_MASK 0x0004 /* SPKL_MUTE_ZC */
-#define WM8915_SPKL_MUTE_ZC_SHIFT 2 /* SPKL_MUTE_ZC */
-#define WM8915_SPKL_MUTE_ZC_WIDTH 1 /* SPKL_MUTE_ZC */
-#define WM8915_SPKL_SRC_MASK 0x0003 /* SPKL_SRC - [1:0] */
-#define WM8915_SPKL_SRC_SHIFT 0 /* SPKL_SRC - [1:0] */
-#define WM8915_SPKL_SRC_WIDTH 2 /* SPKL_SRC - [1:0] */
-
-/*
- * R2049 (0x801) - Right PDM Speaker
- */
-#define WM8915_SPKR_ENA 0x0010 /* SPKR_ENA */
-#define WM8915_SPKR_ENA_MASK 0x0010 /* SPKR_ENA */
-#define WM8915_SPKR_ENA_SHIFT 4 /* SPKR_ENA */
-#define WM8915_SPKR_ENA_WIDTH 1 /* SPKR_ENA */
-#define WM8915_SPKR_MUTE 0x0008 /* SPKR_MUTE */
-#define WM8915_SPKR_MUTE_MASK 0x0008 /* SPKR_MUTE */
-#define WM8915_SPKR_MUTE_SHIFT 3 /* SPKR_MUTE */
-#define WM8915_SPKR_MUTE_WIDTH 1 /* SPKR_MUTE */
-#define WM8915_SPKR_MUTE_ZC 0x0004 /* SPKR_MUTE_ZC */
-#define WM8915_SPKR_MUTE_ZC_MASK 0x0004 /* SPKR_MUTE_ZC */
-#define WM8915_SPKR_MUTE_ZC_SHIFT 2 /* SPKR_MUTE_ZC */
-#define WM8915_SPKR_MUTE_ZC_WIDTH 1 /* SPKR_MUTE_ZC */
-#define WM8915_SPKR_SRC_MASK 0x0003 /* SPKR_SRC - [1:0] */
-#define WM8915_SPKR_SRC_SHIFT 0 /* SPKR_SRC - [1:0] */
-#define WM8915_SPKR_SRC_WIDTH 2 /* SPKR_SRC - [1:0] */
-
-/*
- * R2050 (0x802) - PDM Speaker Mute Sequence
- */
-#define WM8915_SPK_MUTE_ENDIAN 0x0100 /* SPK_MUTE_ENDIAN */
-#define WM8915_SPK_MUTE_ENDIAN_MASK 0x0100 /* SPK_MUTE_ENDIAN */
-#define WM8915_SPK_MUTE_ENDIAN_SHIFT 8 /* SPK_MUTE_ENDIAN */
-#define WM8915_SPK_MUTE_ENDIAN_WIDTH 1 /* SPK_MUTE_ENDIAN */
-#define WM8915_SPK_MUTE_SEQ1_MASK 0x00FF /* SPK_MUTE_SEQ1 - [7:0] */
-#define WM8915_SPK_MUTE_SEQ1_SHIFT 0 /* SPK_MUTE_SEQ1 - [7:0] */
-#define WM8915_SPK_MUTE_SEQ1_WIDTH 8 /* SPK_MUTE_SEQ1 - [7:0] */
-
-/*
- * R2051 (0x803) - PDM Speaker Volume
- */
-#define WM8915_SPKR_VOL_MASK 0x00F0 /* SPKR_VOL - [7:4] */
-#define WM8915_SPKR_VOL_SHIFT 4 /* SPKR_VOL - [7:4] */
-#define WM8915_SPKR_VOL_WIDTH 4 /* SPKR_VOL - [7:4] */
-#define WM8915_SPKL_VOL_MASK 0x000F /* SPKL_VOL - [3:0] */
-#define WM8915_SPKL_VOL_SHIFT 0 /* SPKL_VOL - [3:0] */
-#define WM8915_SPKL_VOL_WIDTH 4 /* SPKL_VOL - [3:0] */
-
-#endif
--- /dev/null
+/*
+ * wm8996.c - WM8996 audio codec interface
+ *
+ * Copyright 2011 Wolfson Microelectronics PLC.
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <linux/gcd.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/workqueue.h>
+#include <sound/core.h>
+#include <sound/jack.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+#include <trace/events/asoc.h>
+
+#include <sound/wm8996.h>
+#include "wm8996.h"
+
+#define WM8996_AIFS 2
+
+#define HPOUT1L 1
+#define HPOUT1R 2
+#define HPOUT2L 4
+#define HPOUT2R 8
+
+#define WM8996_NUM_SUPPLIES 4
+static const char *wm8996_supply_names[WM8996_NUM_SUPPLIES] = {
+ "DBVDD",
+ "AVDD1",
+ "AVDD2",
+ "CPVDD",
+};
+
+struct wm8996_priv {
+ struct snd_soc_codec *codec;
+
+ int ldo1ena;
+
+ int sysclk;
+ int sysclk_src;
+
+ int fll_src;
+ int fll_fref;
+ int fll_fout;
+
+ struct completion fll_lock;
+
+ u16 dcs_pending;
+ struct completion dcs_done;
+
+ u16 hpout_ena;
+ u16 hpout_pending;
+
+ struct regulator_bulk_data supplies[WM8996_NUM_SUPPLIES];
+ struct notifier_block disable_nb[WM8996_NUM_SUPPLIES];
+
+ struct wm8996_pdata pdata;
+
+ int rx_rate[WM8996_AIFS];
+ int bclk_rate[WM8996_AIFS];
+
+ /* Platform dependant ReTune mobile configuration */
+ int num_retune_mobile_texts;
+ const char **retune_mobile_texts;
+ int retune_mobile_cfg[2];
+ struct soc_enum retune_mobile_enum;
+
+ struct snd_soc_jack *jack;
+ bool detecting;
+ bool jack_mic;
+ wm8996_polarity_fn polarity_cb;
+
+#ifdef CONFIG_GPIOLIB
+ struct gpio_chip gpio_chip;
+#endif
+};
+
+/* We can't use the same notifier block for more than one supply and
+ * there's no way I can see to get from a callback to the caller
+ * except container_of().
+ */
+#define WM8996_REGULATOR_EVENT(n) \
+static int wm8996_regulator_event_##n(struct notifier_block *nb, \
+ unsigned long event, void *data) \
+{ \
+ struct wm8996_priv *wm8996 = container_of(nb, struct wm8996_priv, \
+ disable_nb[n]); \
+ if (event & REGULATOR_EVENT_DISABLE) { \
+ wm8996->codec->cache_sync = 1; \
+ } \
+ return 0; \
+}
+
+WM8996_REGULATOR_EVENT(0)
+WM8996_REGULATOR_EVENT(1)
+WM8996_REGULATOR_EVENT(2)
+WM8996_REGULATOR_EVENT(3)
+
+static const u16 wm8996_reg[WM8996_MAX_REGISTER] = {
+ [WM8996_SOFTWARE_RESET] = 0x8996,
+ [WM8996_POWER_MANAGEMENT_7] = 0x10,
+ [WM8996_DAC1_HPOUT1_VOLUME] = 0x88,
+ [WM8996_DAC2_HPOUT2_VOLUME] = 0x88,
+ [WM8996_DAC1_LEFT_VOLUME] = 0x2c0,
+ [WM8996_DAC1_RIGHT_VOLUME] = 0x2c0,
+ [WM8996_DAC2_LEFT_VOLUME] = 0x2c0,
+ [WM8996_DAC2_RIGHT_VOLUME] = 0x2c0,
+ [WM8996_OUTPUT1_LEFT_VOLUME] = 0x80,
+ [WM8996_OUTPUT1_RIGHT_VOLUME] = 0x80,
+ [WM8996_OUTPUT2_LEFT_VOLUME] = 0x80,
+ [WM8996_OUTPUT2_RIGHT_VOLUME] = 0x80,
+ [WM8996_MICBIAS_1] = 0x39,
+ [WM8996_MICBIAS_2] = 0x39,
+ [WM8996_LDO_1] = 0x3,
+ [WM8996_LDO_2] = 0x13,
+ [WM8996_ACCESSORY_DETECT_MODE_1] = 0x4,
+ [WM8996_HEADPHONE_DETECT_1] = 0x20,
+ [WM8996_MIC_DETECT_1] = 0x7600,
+ [WM8996_MIC_DETECT_2] = 0xbf,
+ [WM8996_CHARGE_PUMP_1] = 0x1f25,
+ [WM8996_CHARGE_PUMP_2] = 0xab19,
+ [WM8996_DC_SERVO_5] = 0x2a2a,
+ [WM8996_CONTROL_INTERFACE_1] = 0x8004,
+ [WM8996_CLOCKING_1] = 0x10,
+ [WM8996_AIF_RATE] = 0x83,
+ [WM8996_FLL_CONTROL_4] = 0x5dc0,
+ [WM8996_FLL_CONTROL_5] = 0xc84,
+ [WM8996_FLL_EFS_2] = 0x2,
+ [WM8996_AIF1_TX_LRCLK_1] = 0x80,
+ [WM8996_AIF1_TX_LRCLK_2] = 0x8,
+ [WM8996_AIF1_RX_LRCLK_1] = 0x80,
+ [WM8996_AIF1TX_DATA_CONFIGURATION_1] = 0x1818,
+ [WM8996_AIF1RX_DATA_CONFIGURATION] = 0x1818,
+ [WM8996_AIF1TX_TEST] = 0x7,
+ [WM8996_AIF2_TX_LRCLK_1] = 0x80,
+ [WM8996_AIF2_TX_LRCLK_2] = 0x8,
+ [WM8996_AIF2_RX_LRCLK_1] = 0x80,
+ [WM8996_AIF2TX_DATA_CONFIGURATION_1] = 0x1818,
+ [WM8996_AIF2RX_DATA_CONFIGURATION] = 0x1818,
+ [WM8996_AIF2TX_TEST] = 0x1,
+ [WM8996_DSP1_TX_LEFT_VOLUME] = 0xc0,
+ [WM8996_DSP1_TX_RIGHT_VOLUME] = 0xc0,
+ [WM8996_DSP1_RX_LEFT_VOLUME] = 0xc0,
+ [WM8996_DSP1_RX_RIGHT_VOLUME] = 0xc0,
+ [WM8996_DSP1_TX_FILTERS] = 0x2000,
+ [WM8996_DSP1_RX_FILTERS_1] = 0x200,
+ [WM8996_DSP1_RX_FILTERS_2] = 0x10,
+ [WM8996_DSP1_DRC_1] = 0x98,
+ [WM8996_DSP1_DRC_2] = 0x845,
+ [WM8996_DSP1_RX_EQ_GAINS_1] = 0x6318,
+ [WM8996_DSP1_RX_EQ_GAINS_2] = 0x6300,
+ [WM8996_DSP1_RX_EQ_BAND_1_A] = 0xfca,
+ [WM8996_DSP1_RX_EQ_BAND_1_B] = 0x400,
+ [WM8996_DSP1_RX_EQ_BAND_1_PG] = 0xd8,
+ [WM8996_DSP1_RX_EQ_BAND_2_A] = 0x1eb5,
+ [WM8996_DSP1_RX_EQ_BAND_2_B] = 0xf145,
+ [WM8996_DSP1_RX_EQ_BAND_2_C] = 0xb75,
+ [WM8996_DSP1_RX_EQ_BAND_2_PG] = 0x1c5,
+ [WM8996_DSP1_RX_EQ_BAND_3_A] = 0x1c58,
+ [WM8996_DSP1_RX_EQ_BAND_3_B] = 0xf373,
+ [WM8996_DSP1_RX_EQ_BAND_3_C] = 0xa54,
+ [WM8996_DSP1_RX_EQ_BAND_3_PG] = 0x558,
+ [WM8996_DSP1_RX_EQ_BAND_4_A] = 0x168e,
+ [WM8996_DSP1_RX_EQ_BAND_4_B] = 0xf829,
+ [WM8996_DSP1_RX_EQ_BAND_4_C] = 0x7ad,
+ [WM8996_DSP1_RX_EQ_BAND_4_PG] = 0x1103,
+ [WM8996_DSP1_RX_EQ_BAND_5_A] = 0x564,
+ [WM8996_DSP1_RX_EQ_BAND_5_B] = 0x559,
+ [WM8996_DSP1_RX_EQ_BAND_5_PG] = 0x4000,
+ [WM8996_DSP2_TX_LEFT_VOLUME] = 0xc0,
+ [WM8996_DSP2_TX_RIGHT_VOLUME] = 0xc0,
+ [WM8996_DSP2_RX_LEFT_VOLUME] = 0xc0,
+ [WM8996_DSP2_RX_RIGHT_VOLUME] = 0xc0,
+ [WM8996_DSP2_TX_FILTERS] = 0x2000,
+ [WM8996_DSP2_RX_FILTERS_1] = 0x200,
+ [WM8996_DSP2_RX_FILTERS_2] = 0x10,
+ [WM8996_DSP2_DRC_1] = 0x98,
+ [WM8996_DSP2_DRC_2] = 0x845,
+ [WM8996_DSP2_RX_EQ_GAINS_1] = 0x6318,
+ [WM8996_DSP2_RX_EQ_GAINS_2] = 0x6300,
+ [WM8996_DSP2_RX_EQ_BAND_1_A] = 0xfca,
+ [WM8996_DSP2_RX_EQ_BAND_1_B] = 0x400,
+ [WM8996_DSP2_RX_EQ_BAND_1_PG] = 0xd8,
+ [WM8996_DSP2_RX_EQ_BAND_2_A] = 0x1eb5,
+ [WM8996_DSP2_RX_EQ_BAND_2_B] = 0xf145,
+ [WM8996_DSP2_RX_EQ_BAND_2_C] = 0xb75,
+ [WM8996_DSP2_RX_EQ_BAND_2_PG] = 0x1c5,
+ [WM8996_DSP2_RX_EQ_BAND_3_A] = 0x1c58,
+ [WM8996_DSP2_RX_EQ_BAND_3_B] = 0xf373,
+ [WM8996_DSP2_RX_EQ_BAND_3_C] = 0xa54,
+ [WM8996_DSP2_RX_EQ_BAND_3_PG] = 0x558,
+ [WM8996_DSP2_RX_EQ_BAND_4_A] = 0x168e,
+ [WM8996_DSP2_RX_EQ_BAND_4_B] = 0xf829,
+ [WM8996_DSP2_RX_EQ_BAND_4_C] = 0x7ad,
+ [WM8996_DSP2_RX_EQ_BAND_4_PG] = 0x1103,
+ [WM8996_DSP2_RX_EQ_BAND_5_A] = 0x564,
+ [WM8996_DSP2_RX_EQ_BAND_5_B] = 0x559,
+ [WM8996_DSP2_RX_EQ_BAND_5_PG] = 0x4000,
+ [WM8996_OVERSAMPLING] = 0xd,
+ [WM8996_SIDETONE] = 0x1040,
+ [WM8996_GPIO_1] = 0xa101,
+ [WM8996_GPIO_2] = 0xa101,
+ [WM8996_GPIO_3] = 0xa101,
+ [WM8996_GPIO_4] = 0xa101,
+ [WM8996_GPIO_5] = 0xa101,
+ [WM8996_PULL_CONTROL_2] = 0x140,
+ [WM8996_INTERRUPT_STATUS_1_MASK] = 0x1f,
+ [WM8996_INTERRUPT_STATUS_2_MASK] = 0x1ecf,
+ [WM8996_RIGHT_PDM_SPEAKER] = 0x1,
+ [WM8996_PDM_SPEAKER_MUTE_SEQUENCE] = 0x69,
+ [WM8996_PDM_SPEAKER_VOLUME] = 0x66,
+ [WM8996_WRITE_SEQUENCER_0] = 0x1,
+ [WM8996_WRITE_SEQUENCER_1] = 0x1,
+ [WM8996_WRITE_SEQUENCER_3] = 0x6,
+ [WM8996_WRITE_SEQUENCER_4] = 0x40,
+ [WM8996_WRITE_SEQUENCER_5] = 0x1,
+ [WM8996_WRITE_SEQUENCER_6] = 0xf,
+ [WM8996_WRITE_SEQUENCER_7] = 0x6,
+ [WM8996_WRITE_SEQUENCER_8] = 0x1,
+ [WM8996_WRITE_SEQUENCER_9] = 0x3,
+ [WM8996_WRITE_SEQUENCER_10] = 0x104,
+ [WM8996_WRITE_SEQUENCER_12] = 0x60,
+ [WM8996_WRITE_SEQUENCER_13] = 0x11,
+ [WM8996_WRITE_SEQUENCER_14] = 0x401,
+ [WM8996_WRITE_SEQUENCER_16] = 0x50,
+ [WM8996_WRITE_SEQUENCER_17] = 0x3,
+ [WM8996_WRITE_SEQUENCER_18] = 0x100,
+ [WM8996_WRITE_SEQUENCER_20] = 0x51,
+ [WM8996_WRITE_SEQUENCER_21] = 0x3,
+ [WM8996_WRITE_SEQUENCER_22] = 0x104,
+ [WM8996_WRITE_SEQUENCER_23] = 0xa,
+ [WM8996_WRITE_SEQUENCER_24] = 0x60,
+ [WM8996_WRITE_SEQUENCER_25] = 0x3b,
+ [WM8996_WRITE_SEQUENCER_26] = 0x502,
+ [WM8996_WRITE_SEQUENCER_27] = 0x100,
+ [WM8996_WRITE_SEQUENCER_28] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_32] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_36] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_40] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_44] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_48] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_52] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_56] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_60] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_64] = 0x1,
+ [WM8996_WRITE_SEQUENCER_65] = 0x1,
+ [WM8996_WRITE_SEQUENCER_67] = 0x6,
+ [WM8996_WRITE_SEQUENCER_68] = 0x40,
+ [WM8996_WRITE_SEQUENCER_69] = 0x1,
+ [WM8996_WRITE_SEQUENCER_70] = 0xf,
+ [WM8996_WRITE_SEQUENCER_71] = 0x6,
+ [WM8996_WRITE_SEQUENCER_72] = 0x1,
+ [WM8996_WRITE_SEQUENCER_73] = 0x3,
+ [WM8996_WRITE_SEQUENCER_74] = 0x104,
+ [WM8996_WRITE_SEQUENCER_76] = 0x60,
+ [WM8996_WRITE_SEQUENCER_77] = 0x11,
+ [WM8996_WRITE_SEQUENCER_78] = 0x401,
+ [WM8996_WRITE_SEQUENCER_80] = 0x50,
+ [WM8996_WRITE_SEQUENCER_81] = 0x3,
+ [WM8996_WRITE_SEQUENCER_82] = 0x100,
+ [WM8996_WRITE_SEQUENCER_84] = 0x60,
+ [WM8996_WRITE_SEQUENCER_85] = 0x3b,
+ [WM8996_WRITE_SEQUENCER_86] = 0x502,
+ [WM8996_WRITE_SEQUENCER_87] = 0x100,
+ [WM8996_WRITE_SEQUENCER_88] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_92] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_96] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_100] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_104] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_108] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_112] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_116] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_120] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_124] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_128] = 0x1,
+ [WM8996_WRITE_SEQUENCER_129] = 0x1,
+ [WM8996_WRITE_SEQUENCER_131] = 0x6,
+ [WM8996_WRITE_SEQUENCER_132] = 0x40,
+ [WM8996_WRITE_SEQUENCER_133] = 0x1,
+ [WM8996_WRITE_SEQUENCER_134] = 0xf,
+ [WM8996_WRITE_SEQUENCER_135] = 0x6,
+ [WM8996_WRITE_SEQUENCER_136] = 0x1,
+ [WM8996_WRITE_SEQUENCER_137] = 0x3,
+ [WM8996_WRITE_SEQUENCER_138] = 0x106,
+ [WM8996_WRITE_SEQUENCER_140] = 0x61,
+ [WM8996_WRITE_SEQUENCER_141] = 0x11,
+ [WM8996_WRITE_SEQUENCER_142] = 0x401,
+ [WM8996_WRITE_SEQUENCER_144] = 0x50,
+ [WM8996_WRITE_SEQUENCER_145] = 0x3,
+ [WM8996_WRITE_SEQUENCER_146] = 0x102,
+ [WM8996_WRITE_SEQUENCER_148] = 0x51,
+ [WM8996_WRITE_SEQUENCER_149] = 0x3,
+ [WM8996_WRITE_SEQUENCER_150] = 0x106,
+ [WM8996_WRITE_SEQUENCER_151] = 0xa,
+ [WM8996_WRITE_SEQUENCER_152] = 0x61,
+ [WM8996_WRITE_SEQUENCER_153] = 0x3b,
+ [WM8996_WRITE_SEQUENCER_154] = 0x502,
+ [WM8996_WRITE_SEQUENCER_155] = 0x100,
+ [WM8996_WRITE_SEQUENCER_156] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_160] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_164] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_168] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_172] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_176] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_180] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_184] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_188] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_192] = 0x1,
+ [WM8996_WRITE_SEQUENCER_193] = 0x1,
+ [WM8996_WRITE_SEQUENCER_195] = 0x6,
+ [WM8996_WRITE_SEQUENCER_196] = 0x40,
+ [WM8996_WRITE_SEQUENCER_197] = 0x1,
+ [WM8996_WRITE_SEQUENCER_198] = 0xf,
+ [WM8996_WRITE_SEQUENCER_199] = 0x6,
+ [WM8996_WRITE_SEQUENCER_200] = 0x1,
+ [WM8996_WRITE_SEQUENCER_201] = 0x3,
+ [WM8996_WRITE_SEQUENCER_202] = 0x106,
+ [WM8996_WRITE_SEQUENCER_204] = 0x61,
+ [WM8996_WRITE_SEQUENCER_205] = 0x11,
+ [WM8996_WRITE_SEQUENCER_206] = 0x401,
+ [WM8996_WRITE_SEQUENCER_208] = 0x50,
+ [WM8996_WRITE_SEQUENCER_209] = 0x3,
+ [WM8996_WRITE_SEQUENCER_210] = 0x102,
+ [WM8996_WRITE_SEQUENCER_212] = 0x61,
+ [WM8996_WRITE_SEQUENCER_213] = 0x3b,
+ [WM8996_WRITE_SEQUENCER_214] = 0x502,
+ [WM8996_WRITE_SEQUENCER_215] = 0x100,
+ [WM8996_WRITE_SEQUENCER_216] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_220] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_224] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_228] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_232] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_236] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_240] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_244] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_248] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_252] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_256] = 0x60,
+ [WM8996_WRITE_SEQUENCER_258] = 0x601,
+ [WM8996_WRITE_SEQUENCER_260] = 0x50,
+ [WM8996_WRITE_SEQUENCER_262] = 0x100,
+ [WM8996_WRITE_SEQUENCER_264] = 0x1,
+ [WM8996_WRITE_SEQUENCER_266] = 0x104,
+ [WM8996_WRITE_SEQUENCER_267] = 0x100,
+ [WM8996_WRITE_SEQUENCER_268] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_272] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_276] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_280] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_284] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_288] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_292] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_296] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_300] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_304] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_308] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_312] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_316] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_320] = 0x61,
+ [WM8996_WRITE_SEQUENCER_322] = 0x601,
+ [WM8996_WRITE_SEQUENCER_324] = 0x50,
+ [WM8996_WRITE_SEQUENCER_326] = 0x102,
+ [WM8996_WRITE_SEQUENCER_328] = 0x1,
+ [WM8996_WRITE_SEQUENCER_330] = 0x106,
+ [WM8996_WRITE_SEQUENCER_331] = 0x100,
+ [WM8996_WRITE_SEQUENCER_332] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_336] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_340] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_344] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_348] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_352] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_356] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_360] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_364] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_368] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_372] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_376] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_380] = 0x2fff,
+ [WM8996_WRITE_SEQUENCER_384] = 0x60,
+ [WM8996_WRITE_SEQUENCER_386] = 0x601,
+ [WM8996_WRITE_SEQUENCER_388] = 0x61,
+ [WM8996_WRITE_SEQUENCER_390] = 0x601,
+ [WM8996_WRITE_SEQUENCER_392] = 0x50,
+ [WM8996_WRITE_SEQUENCER_394] = 0x300,
+ [WM8996_WRITE_SEQUENCER_396] = 0x1,
+ [WM8996_WRITE_SEQUENCER_398] = 0x304,
+ [WM8996_WRITE_SEQUENCER_400] = 0x40,
+ [WM8996_WRITE_SEQUENCER_402] = 0xf,
+ [WM8996_WRITE_SEQUENCER_404] = 0x1,
+ [WM8996_WRITE_SEQUENCER_407] = 0x100,
+};
+
+static const DECLARE_TLV_DB_SCALE(inpga_tlv, 0, 100, 0);
+static const DECLARE_TLV_DB_SCALE(sidetone_tlv, -3600, 150, 0);
+static const DECLARE_TLV_DB_SCALE(digital_tlv, -7200, 75, 1);
+static const DECLARE_TLV_DB_SCALE(out_digital_tlv, -1200, 150, 0);
+static const DECLARE_TLV_DB_SCALE(out_tlv, -900, 75, 0);
+static const DECLARE_TLV_DB_SCALE(spk_tlv, -900, 150, 0);
+static const DECLARE_TLV_DB_SCALE(eq_tlv, -1200, 100, 0);
+
+static const char *sidetone_hpf_text[] = {
+ "2.9kHz", "1.5kHz", "735Hz", "403Hz", "196Hz", "98Hz", "49Hz"
+};
+
+static const struct soc_enum sidetone_hpf =
+ SOC_ENUM_SINGLE(WM8996_SIDETONE, 7, 6, sidetone_hpf_text);
+
+static const char *hpf_mode_text[] = {
+ "HiFi", "Custom", "Voice"
+};
+
+static const struct soc_enum dsp1tx_hpf_mode =
+ SOC_ENUM_SINGLE(WM8996_DSP1_TX_FILTERS, 3, 3, hpf_mode_text);
+
+static const struct soc_enum dsp2tx_hpf_mode =
+ SOC_ENUM_SINGLE(WM8996_DSP2_TX_FILTERS, 3, 3, hpf_mode_text);
+
+static const char *hpf_cutoff_text[] = {
+ "50Hz", "75Hz", "100Hz", "150Hz", "200Hz", "300Hz", "400Hz"
+};
+
+static const struct soc_enum dsp1tx_hpf_cutoff =
+ SOC_ENUM_SINGLE(WM8996_DSP1_TX_FILTERS, 0, 7, hpf_cutoff_text);
+
+static const struct soc_enum dsp2tx_hpf_cutoff =
+ SOC_ENUM_SINGLE(WM8996_DSP2_TX_FILTERS, 0, 7, hpf_cutoff_text);
+
+static void wm8996_set_retune_mobile(struct snd_soc_codec *codec, int block)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct wm8996_pdata *pdata = &wm8996->pdata;
+ int base, best, best_val, save, i, cfg, iface;
+
+ if (!wm8996->num_retune_mobile_texts)
+ return;
+
+ switch (block) {
+ case 0:
+ base = WM8996_DSP1_RX_EQ_GAINS_1;
+ if (snd_soc_read(codec, WM8996_POWER_MANAGEMENT_8) &
+ WM8996_DSP1RX_SRC)
+ iface = 1;
+ else
+ iface = 0;
+ break;
+ case 1:
+ base = WM8996_DSP1_RX_EQ_GAINS_2;
+ if (snd_soc_read(codec, WM8996_POWER_MANAGEMENT_8) &
+ WM8996_DSP2RX_SRC)
+ iface = 1;
+ else
+ iface = 0;
+ break;
+ default:
+ return;
+ }
+
+ /* Find the version of the currently selected configuration
+ * with the nearest sample rate. */
+ cfg = wm8996->retune_mobile_cfg[block];
+ best = 0;
+ best_val = INT_MAX;
+ for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
+ if (strcmp(pdata->retune_mobile_cfgs[i].name,
+ wm8996->retune_mobile_texts[cfg]) == 0 &&
+ abs(pdata->retune_mobile_cfgs[i].rate
+ - wm8996->rx_rate[iface]) < best_val) {
+ best = i;
+ best_val = abs(pdata->retune_mobile_cfgs[i].rate
+ - wm8996->rx_rate[iface]);
+ }
+ }
+
+ dev_dbg(codec->dev, "ReTune Mobile %d %s/%dHz for %dHz sample rate\n",
+ block,
+ pdata->retune_mobile_cfgs[best].name,
+ pdata->retune_mobile_cfgs[best].rate,
+ wm8996->rx_rate[iface]);
+
+ /* The EQ will be disabled while reconfiguring it, remember the
+ * current configuration.
+ */
+ save = snd_soc_read(codec, base);
+ save &= WM8996_DSP1RX_EQ_ENA;
+
+ for (i = 0; i < ARRAY_SIZE(pdata->retune_mobile_cfgs[best].regs); i++)
+ snd_soc_update_bits(codec, base + i, 0xffff,
+ pdata->retune_mobile_cfgs[best].regs[i]);
+
+ snd_soc_update_bits(codec, base, WM8996_DSP1RX_EQ_ENA, save);
+}
+
+/* Icky as hell but saves code duplication */
+static int wm8996_get_retune_mobile_block(const char *name)
+{
+ if (strcmp(name, "DSP1 EQ Mode") == 0)
+ return 0;
+ if (strcmp(name, "DSP2 EQ Mode") == 0)
+ return 1;
+ return -EINVAL;
+}
+
+static int wm8996_put_retune_mobile_enum(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct wm8996_pdata *pdata = &wm8996->pdata;
+ int block = wm8996_get_retune_mobile_block(kcontrol->id.name);
+ int value = ucontrol->value.integer.value[0];
+
+ if (block < 0)
+ return block;
+
+ if (value >= pdata->num_retune_mobile_cfgs)
+ return -EINVAL;
+
+ wm8996->retune_mobile_cfg[block] = value;
+
+ wm8996_set_retune_mobile(codec, block);
+
+ return 0;
+}
+
+static int wm8996_get_retune_mobile_enum(struct snd_kcontrol *kcontrol,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int block = wm8996_get_retune_mobile_block(kcontrol->id.name);
+
+ ucontrol->value.enumerated.item[0] = wm8996->retune_mobile_cfg[block];
+
+ return 0;
+}
+
+static const struct snd_kcontrol_new wm8996_snd_controls[] = {
+SOC_DOUBLE_R_TLV("Capture Volume", WM8996_LEFT_LINE_INPUT_VOLUME,
+ WM8996_RIGHT_LINE_INPUT_VOLUME, 0, 31, 0, inpga_tlv),
+SOC_DOUBLE_R("Capture ZC Switch", WM8996_LEFT_LINE_INPUT_VOLUME,
+ WM8996_RIGHT_LINE_INPUT_VOLUME, 5, 1, 0),
+
+SOC_DOUBLE_TLV("DAC1 Sidetone Volume", WM8996_DAC1_MIXER_VOLUMES,
+ 0, 5, 24, 0, sidetone_tlv),
+SOC_DOUBLE_TLV("DAC2 Sidetone Volume", WM8996_DAC2_MIXER_VOLUMES,
+ 0, 5, 24, 0, sidetone_tlv),
+SOC_SINGLE("Sidetone LPF Switch", WM8996_SIDETONE, 12, 1, 0),
+SOC_ENUM("Sidetone HPF Cut-off", sidetone_hpf),
+SOC_SINGLE("Sidetone HPF Switch", WM8996_SIDETONE, 6, 1, 0),
+
+SOC_DOUBLE_R_TLV("DSP1 Capture Volume", WM8996_DSP1_TX_LEFT_VOLUME,
+ WM8996_DSP1_TX_RIGHT_VOLUME, 1, 96, 0, digital_tlv),
+SOC_DOUBLE_R_TLV("DSP2 Capture Volume", WM8996_DSP2_TX_LEFT_VOLUME,
+ WM8996_DSP2_TX_RIGHT_VOLUME, 1, 96, 0, digital_tlv),
+
+SOC_SINGLE("DSP1 Capture Notch Filter Switch", WM8996_DSP1_TX_FILTERS,
+ 13, 1, 0),
+SOC_DOUBLE("DSP1 Capture HPF Switch", WM8996_DSP1_TX_FILTERS, 12, 11, 1, 0),
+SOC_ENUM("DSP1 Capture HPF Mode", dsp1tx_hpf_mode),
+SOC_ENUM("DSP1 Capture HPF Cutoff", dsp1tx_hpf_cutoff),
+
+SOC_SINGLE("DSP2 Capture Notch Filter Switch", WM8996_DSP2_TX_FILTERS,
+ 13, 1, 0),
+SOC_DOUBLE("DSP2 Capture HPF Switch", WM8996_DSP2_TX_FILTERS, 12, 11, 1, 0),
+SOC_ENUM("DSP2 Capture HPF Mode", dsp2tx_hpf_mode),
+SOC_ENUM("DSP2 Capture HPF Cutoff", dsp2tx_hpf_cutoff),
+
+SOC_DOUBLE_R_TLV("DSP1 Playback Volume", WM8996_DSP1_RX_LEFT_VOLUME,
+ WM8996_DSP1_RX_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
+SOC_SINGLE("DSP1 Playback Switch", WM8996_DSP1_RX_FILTERS_1, 9, 1, 1),
+
+SOC_DOUBLE_R_TLV("DSP2 Playback Volume", WM8996_DSP2_RX_LEFT_VOLUME,
+ WM8996_DSP2_RX_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
+SOC_SINGLE("DSP2 Playback Switch", WM8996_DSP2_RX_FILTERS_1, 9, 1, 1),
+
+SOC_DOUBLE_R_TLV("DAC1 Volume", WM8996_DAC1_LEFT_VOLUME,
+ WM8996_DAC1_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
+SOC_DOUBLE_R("DAC1 Switch", WM8996_DAC1_LEFT_VOLUME,
+ WM8996_DAC1_RIGHT_VOLUME, 9, 1, 1),
+
+SOC_DOUBLE_R_TLV("DAC2 Volume", WM8996_DAC2_LEFT_VOLUME,
+ WM8996_DAC2_RIGHT_VOLUME, 1, 112, 0, digital_tlv),
+SOC_DOUBLE_R("DAC2 Switch", WM8996_DAC2_LEFT_VOLUME,
+ WM8996_DAC2_RIGHT_VOLUME, 9, 1, 1),
+
+SOC_SINGLE("Speaker High Performance Switch", WM8996_OVERSAMPLING, 3, 1, 0),
+SOC_SINGLE("DMIC High Performance Switch", WM8996_OVERSAMPLING, 2, 1, 0),
+SOC_SINGLE("ADC High Performance Switch", WM8996_OVERSAMPLING, 1, 1, 0),
+SOC_SINGLE("DAC High Performance Switch", WM8996_OVERSAMPLING, 0, 1, 0),
+
+SOC_SINGLE("DAC Soft Mute Switch", WM8996_DAC_SOFTMUTE, 1, 1, 0),
+SOC_SINGLE("DAC Slow Soft Mute Switch", WM8996_DAC_SOFTMUTE, 0, 1, 0),
+
+SOC_DOUBLE_TLV("Digital Output 1 Volume", WM8996_DAC1_HPOUT1_VOLUME, 0, 4,
+ 8, 0, out_digital_tlv),
+SOC_DOUBLE_TLV("Digital Output 2 Volume", WM8996_DAC2_HPOUT2_VOLUME, 0, 4,
+ 8, 0, out_digital_tlv),
+
+SOC_DOUBLE_R_TLV("Output 1 Volume", WM8996_OUTPUT1_LEFT_VOLUME,
+ WM8996_OUTPUT1_RIGHT_VOLUME, 0, 12, 0, out_tlv),
+SOC_DOUBLE_R("Output 1 ZC Switch", WM8996_OUTPUT1_LEFT_VOLUME,
+ WM8996_OUTPUT1_RIGHT_VOLUME, 7, 1, 0),
+
+SOC_DOUBLE_R_TLV("Output 2 Volume", WM8996_OUTPUT2_LEFT_VOLUME,
+ WM8996_OUTPUT2_RIGHT_VOLUME, 0, 12, 0, out_tlv),
+SOC_DOUBLE_R("Output 2 ZC Switch", WM8996_OUTPUT2_LEFT_VOLUME,
+ WM8996_OUTPUT2_RIGHT_VOLUME, 7, 1, 0),
+
+SOC_DOUBLE_TLV("Speaker Volume", WM8996_PDM_SPEAKER_VOLUME, 0, 4, 8, 0,
+ spk_tlv),
+SOC_DOUBLE_R("Speaker Switch", WM8996_LEFT_PDM_SPEAKER,
+ WM8996_RIGHT_PDM_SPEAKER, 3, 1, 1),
+SOC_DOUBLE_R("Speaker ZC Switch", WM8996_LEFT_PDM_SPEAKER,
+ WM8996_RIGHT_PDM_SPEAKER, 2, 1, 0),
+
+SOC_SINGLE("DSP1 EQ Switch", WM8996_DSP1_RX_EQ_GAINS_1, 0, 1, 0),
+SOC_SINGLE("DSP2 EQ Switch", WM8996_DSP2_RX_EQ_GAINS_1, 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new wm8996_eq_controls[] = {
+SOC_SINGLE_TLV("DSP1 EQ B1 Volume", WM8996_DSP1_RX_EQ_GAINS_1, 11, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP1 EQ B2 Volume", WM8996_DSP1_RX_EQ_GAINS_1, 6, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP1 EQ B3 Volume", WM8996_DSP1_RX_EQ_GAINS_1, 1, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP1 EQ B4 Volume", WM8996_DSP1_RX_EQ_GAINS_2, 11, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP1 EQ B5 Volume", WM8996_DSP1_RX_EQ_GAINS_2, 6, 31, 0,
+ eq_tlv),
+
+SOC_SINGLE_TLV("DSP2 EQ B1 Volume", WM8996_DSP2_RX_EQ_GAINS_1, 11, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP2 EQ B2 Volume", WM8996_DSP2_RX_EQ_GAINS_1, 6, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP2 EQ B3 Volume", WM8996_DSP2_RX_EQ_GAINS_1, 1, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP2 EQ B4 Volume", WM8996_DSP2_RX_EQ_GAINS_2, 11, 31, 0,
+ eq_tlv),
+SOC_SINGLE_TLV("DSP2 EQ B5 Volume", WM8996_DSP2_RX_EQ_GAINS_2, 6, 31, 0,
+ eq_tlv),
+};
+
+static int cp_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ msleep(5);
+ break;
+ default:
+ BUG();
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int rmv_short_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(w->codec);
+
+ /* Record which outputs we enabled */
+ switch (event) {
+ case SND_SOC_DAPM_PRE_PMD:
+ wm8996->hpout_pending &= ~w->shift;
+ break;
+ case SND_SOC_DAPM_PRE_PMU:
+ wm8996->hpout_pending |= w->shift;
+ break;
+ default:
+ BUG();
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void wait_for_dc_servo(struct snd_soc_codec *codec, u16 mask)
+{
+ struct i2c_client *i2c = to_i2c_client(codec->dev);
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int i, ret;
+ unsigned long timeout = 200;
+
+ snd_soc_write(codec, WM8996_DC_SERVO_2, mask);
+
+ /* Use the interrupt if possible */
+ do {
+ if (i2c->irq) {
+ timeout = wait_for_completion_timeout(&wm8996->dcs_done,
+ msecs_to_jiffies(200));
+ if (timeout == 0)
+ dev_err(codec->dev, "DC servo timed out\n");
+
+ } else {
+ msleep(1);
+ if (--i) {
+ timeout = 0;
+ break;
+ }
+ }
+
+ ret = snd_soc_read(codec, WM8996_DC_SERVO_2);
+ dev_dbg(codec->dev, "DC servo state: %x\n", ret);
+ } while (ret & mask);
+
+ if (timeout == 0)
+ dev_err(codec->dev, "DC servo timed out for %x\n", mask);
+ else
+ dev_dbg(codec->dev, "DC servo complete for %x\n", mask);
+}
+
+static void wm8996_seq_notifier(struct snd_soc_dapm_context *dapm,
+ enum snd_soc_dapm_type event, int subseq)
+{
+ struct snd_soc_codec *codec = container_of(dapm,
+ struct snd_soc_codec, dapm);
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ u16 val, mask;
+
+ /* Complete any pending DC servo starts */
+ if (wm8996->dcs_pending) {
+ dev_dbg(codec->dev, "Starting DC servo for %x\n",
+ wm8996->dcs_pending);
+
+ /* Trigger a startup sequence */
+ wait_for_dc_servo(codec, wm8996->dcs_pending
+ << WM8996_DCS_TRIG_STARTUP_0_SHIFT);
+
+ wm8996->dcs_pending = 0;
+ }
+
+ if (wm8996->hpout_pending != wm8996->hpout_ena) {
+ dev_dbg(codec->dev, "Applying RMV_SHORTs %x->%x\n",
+ wm8996->hpout_ena, wm8996->hpout_pending);
+
+ val = 0;
+ mask = 0;
+ if (wm8996->hpout_pending & HPOUT1L) {
+ val |= WM8996_HPOUT1L_RMV_SHORT;
+ mask |= WM8996_HPOUT1L_RMV_SHORT;
+ } else {
+ mask |= WM8996_HPOUT1L_RMV_SHORT |
+ WM8996_HPOUT1L_OUTP |
+ WM8996_HPOUT1L_DLY;
+ }
+
+ if (wm8996->hpout_pending & HPOUT1R) {
+ val |= WM8996_HPOUT1R_RMV_SHORT;
+ mask |= WM8996_HPOUT1R_RMV_SHORT;
+ } else {
+ mask |= WM8996_HPOUT1R_RMV_SHORT |
+ WM8996_HPOUT1R_OUTP |
+ WM8996_HPOUT1R_DLY;
+ }
+
+ snd_soc_update_bits(codec, WM8996_ANALOGUE_HP_1, mask, val);
+
+ val = 0;
+ mask = 0;
+ if (wm8996->hpout_pending & HPOUT2L) {
+ val |= WM8996_HPOUT2L_RMV_SHORT;
+ mask |= WM8996_HPOUT2L_RMV_SHORT;
+ } else {
+ mask |= WM8996_HPOUT2L_RMV_SHORT |
+ WM8996_HPOUT2L_OUTP |
+ WM8996_HPOUT2L_DLY;
+ }
+
+ if (wm8996->hpout_pending & HPOUT2R) {
+ val |= WM8996_HPOUT2R_RMV_SHORT;
+ mask |= WM8996_HPOUT2R_RMV_SHORT;
+ } else {
+ mask |= WM8996_HPOUT2R_RMV_SHORT |
+ WM8996_HPOUT2R_OUTP |
+ WM8996_HPOUT2R_DLY;
+ }
+
+ snd_soc_update_bits(codec, WM8996_ANALOGUE_HP_2, mask, val);
+
+ wm8996->hpout_ena = wm8996->hpout_pending;
+ }
+}
+
+static int dcs_start(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *kcontrol, int event)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(w->codec);
+
+ switch (event) {
+ case SND_SOC_DAPM_POST_PMU:
+ wm8996->dcs_pending |= 1 << w->shift;
+ break;
+ default:
+ BUG();
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const char *sidetone_text[] = {
+ "IN1", "IN2",
+};
+
+static const struct soc_enum left_sidetone_enum =
+ SOC_ENUM_SINGLE(WM8996_SIDETONE, 0, 2, sidetone_text);
+
+static const struct snd_kcontrol_new left_sidetone =
+ SOC_DAPM_ENUM("Left Sidetone", left_sidetone_enum);
+
+static const struct soc_enum right_sidetone_enum =
+ SOC_ENUM_SINGLE(WM8996_SIDETONE, 1, 2, sidetone_text);
+
+static const struct snd_kcontrol_new right_sidetone =
+ SOC_DAPM_ENUM("Right Sidetone", right_sidetone_enum);
+
+static const char *spk_text[] = {
+ "DAC1L", "DAC1R", "DAC2L", "DAC2R"
+};
+
+static const struct soc_enum spkl_enum =
+ SOC_ENUM_SINGLE(WM8996_LEFT_PDM_SPEAKER, 0, 4, spk_text);
+
+static const struct snd_kcontrol_new spkl_mux =
+ SOC_DAPM_ENUM("SPKL", spkl_enum);
+
+static const struct soc_enum spkr_enum =
+ SOC_ENUM_SINGLE(WM8996_RIGHT_PDM_SPEAKER, 0, 4, spk_text);
+
+static const struct snd_kcontrol_new spkr_mux =
+ SOC_DAPM_ENUM("SPKR", spkr_enum);
+
+static const char *dsp1rx_text[] = {
+ "AIF1", "AIF2"
+};
+
+static const struct soc_enum dsp1rx_enum =
+ SOC_ENUM_SINGLE(WM8996_POWER_MANAGEMENT_8, 0, 2, dsp1rx_text);
+
+static const struct snd_kcontrol_new dsp1rx =
+ SOC_DAPM_ENUM("DSP1RX", dsp1rx_enum);
+
+static const char *dsp2rx_text[] = {
+ "AIF2", "AIF1"
+};
+
+static const struct soc_enum dsp2rx_enum =
+ SOC_ENUM_SINGLE(WM8996_POWER_MANAGEMENT_8, 4, 2, dsp2rx_text);
+
+static const struct snd_kcontrol_new dsp2rx =
+ SOC_DAPM_ENUM("DSP2RX", dsp2rx_enum);
+
+static const char *aif2tx_text[] = {
+ "DSP2", "DSP1", "AIF1"
+};
+
+static const struct soc_enum aif2tx_enum =
+ SOC_ENUM_SINGLE(WM8996_POWER_MANAGEMENT_8, 6, 3, aif2tx_text);
+
+static const struct snd_kcontrol_new aif2tx =
+ SOC_DAPM_ENUM("AIF2TX", aif2tx_enum);
+
+static const char *inmux_text[] = {
+ "ADC", "DMIC1", "DMIC2"
+};
+
+static const struct soc_enum in1_enum =
+ SOC_ENUM_SINGLE(WM8996_POWER_MANAGEMENT_7, 0, 3, inmux_text);
+
+static const struct snd_kcontrol_new in1_mux =
+ SOC_DAPM_ENUM("IN1 Mux", in1_enum);
+
+static const struct soc_enum in2_enum =
+ SOC_ENUM_SINGLE(WM8996_POWER_MANAGEMENT_7, 4, 3, inmux_text);
+
+static const struct snd_kcontrol_new in2_mux =
+ SOC_DAPM_ENUM("IN2 Mux", in2_enum);
+
+static const struct snd_kcontrol_new dac2r_mix[] = {
+SOC_DAPM_SINGLE("Right Sidetone Switch", WM8996_DAC2_RIGHT_MIXER_ROUTING,
+ 5, 1, 0),
+SOC_DAPM_SINGLE("Left Sidetone Switch", WM8996_DAC2_RIGHT_MIXER_ROUTING,
+ 4, 1, 0),
+SOC_DAPM_SINGLE("DSP2 Switch", WM8996_DAC2_RIGHT_MIXER_ROUTING, 1, 1, 0),
+SOC_DAPM_SINGLE("DSP1 Switch", WM8996_DAC2_RIGHT_MIXER_ROUTING, 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dac2l_mix[] = {
+SOC_DAPM_SINGLE("Right Sidetone Switch", WM8996_DAC2_LEFT_MIXER_ROUTING,
+ 5, 1, 0),
+SOC_DAPM_SINGLE("Left Sidetone Switch", WM8996_DAC2_LEFT_MIXER_ROUTING,
+ 4, 1, 0),
+SOC_DAPM_SINGLE("DSP2 Switch", WM8996_DAC2_LEFT_MIXER_ROUTING, 1, 1, 0),
+SOC_DAPM_SINGLE("DSP1 Switch", WM8996_DAC2_LEFT_MIXER_ROUTING, 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dac1r_mix[] = {
+SOC_DAPM_SINGLE("Right Sidetone Switch", WM8996_DAC1_RIGHT_MIXER_ROUTING,
+ 5, 1, 0),
+SOC_DAPM_SINGLE("Left Sidetone Switch", WM8996_DAC1_RIGHT_MIXER_ROUTING,
+ 4, 1, 0),
+SOC_DAPM_SINGLE("DSP2 Switch", WM8996_DAC1_RIGHT_MIXER_ROUTING, 1, 1, 0),
+SOC_DAPM_SINGLE("DSP1 Switch", WM8996_DAC1_RIGHT_MIXER_ROUTING, 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dac1l_mix[] = {
+SOC_DAPM_SINGLE("Right Sidetone Switch", WM8996_DAC1_LEFT_MIXER_ROUTING,
+ 5, 1, 0),
+SOC_DAPM_SINGLE("Left Sidetone Switch", WM8996_DAC1_LEFT_MIXER_ROUTING,
+ 4, 1, 0),
+SOC_DAPM_SINGLE("DSP2 Switch", WM8996_DAC1_LEFT_MIXER_ROUTING, 1, 1, 0),
+SOC_DAPM_SINGLE("DSP1 Switch", WM8996_DAC1_LEFT_MIXER_ROUTING, 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dsp1txl[] = {
+SOC_DAPM_SINGLE("IN1 Switch", WM8996_DSP1_TX_LEFT_MIXER_ROUTING,
+ 1, 1, 0),
+SOC_DAPM_SINGLE("DAC Switch", WM8996_DSP1_TX_LEFT_MIXER_ROUTING,
+ 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dsp1txr[] = {
+SOC_DAPM_SINGLE("IN1 Switch", WM8996_DSP1_TX_RIGHT_MIXER_ROUTING,
+ 1, 1, 0),
+SOC_DAPM_SINGLE("DAC Switch", WM8996_DSP1_TX_RIGHT_MIXER_ROUTING,
+ 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dsp2txl[] = {
+SOC_DAPM_SINGLE("IN1 Switch", WM8996_DSP2_TX_LEFT_MIXER_ROUTING,
+ 1, 1, 0),
+SOC_DAPM_SINGLE("DAC Switch", WM8996_DSP2_TX_LEFT_MIXER_ROUTING,
+ 0, 1, 0),
+};
+
+static const struct snd_kcontrol_new dsp2txr[] = {
+SOC_DAPM_SINGLE("IN1 Switch", WM8996_DSP2_TX_RIGHT_MIXER_ROUTING,
+ 1, 1, 0),
+SOC_DAPM_SINGLE("DAC Switch", WM8996_DSP2_TX_RIGHT_MIXER_ROUTING,
+ 0, 1, 0),
+};
+
+
+static const struct snd_soc_dapm_widget wm8996_dapm_widgets[] = {
+SND_SOC_DAPM_INPUT("IN1LN"),
+SND_SOC_DAPM_INPUT("IN1LP"),
+SND_SOC_DAPM_INPUT("IN1RN"),
+SND_SOC_DAPM_INPUT("IN1RP"),
+
+SND_SOC_DAPM_INPUT("IN2LN"),
+SND_SOC_DAPM_INPUT("IN2LP"),
+SND_SOC_DAPM_INPUT("IN2RN"),
+SND_SOC_DAPM_INPUT("IN2RP"),
+
+SND_SOC_DAPM_INPUT("DMIC1DAT"),
+SND_SOC_DAPM_INPUT("DMIC2DAT"),
+
+SND_SOC_DAPM_SUPPLY_S("SYSCLK", 1, WM8996_AIF_CLOCKING_1, 0, 0, NULL, 0),
+SND_SOC_DAPM_SUPPLY_S("SYSDSPCLK", 2, WM8996_CLOCKING_1, 1, 0, NULL, 0),
+SND_SOC_DAPM_SUPPLY_S("AIFCLK", 2, WM8996_CLOCKING_1, 2, 0, NULL, 0),
+SND_SOC_DAPM_SUPPLY_S("Charge Pump", 2, WM8996_CHARGE_PUMP_1, 15, 0, cp_event,
+ SND_SOC_DAPM_POST_PMU),
+
+SND_SOC_DAPM_SUPPLY("LDO2", WM8996_POWER_MANAGEMENT_2, 1, 0, NULL, 0),
+SND_SOC_DAPM_MICBIAS("MICB2", WM8996_POWER_MANAGEMENT_1, 9, 0),
+SND_SOC_DAPM_MICBIAS("MICB1", WM8996_POWER_MANAGEMENT_1, 8, 0),
+
+SND_SOC_DAPM_PGA("IN1L PGA", WM8996_POWER_MANAGEMENT_2, 5, 0, NULL, 0),
+SND_SOC_DAPM_PGA("IN1R PGA", WM8996_POWER_MANAGEMENT_2, 4, 0, NULL, 0),
+
+SND_SOC_DAPM_MUX("IN1L Mux", SND_SOC_NOPM, 0, 0, &in1_mux),
+SND_SOC_DAPM_MUX("IN1R Mux", SND_SOC_NOPM, 0, 0, &in1_mux),
+SND_SOC_DAPM_MUX("IN2L Mux", SND_SOC_NOPM, 0, 0, &in2_mux),
+SND_SOC_DAPM_MUX("IN2R Mux", SND_SOC_NOPM, 0, 0, &in2_mux),
+
+SND_SOC_DAPM_PGA("IN1L", WM8996_POWER_MANAGEMENT_7, 2, 0, NULL, 0),
+SND_SOC_DAPM_PGA("IN1R", WM8996_POWER_MANAGEMENT_7, 3, 0, NULL, 0),
+SND_SOC_DAPM_PGA("IN2L", WM8996_POWER_MANAGEMENT_7, 6, 0, NULL, 0),
+SND_SOC_DAPM_PGA("IN2R", WM8996_POWER_MANAGEMENT_7, 7, 0, NULL, 0),
+
+SND_SOC_DAPM_SUPPLY("DMIC2", WM8996_POWER_MANAGEMENT_7, 9, 0, NULL, 0),
+SND_SOC_DAPM_SUPPLY("DMIC1", WM8996_POWER_MANAGEMENT_7, 8, 0, NULL, 0),
+
+SND_SOC_DAPM_ADC("DMIC2L", NULL, WM8996_POWER_MANAGEMENT_3, 5, 0),
+SND_SOC_DAPM_ADC("DMIC2R", NULL, WM8996_POWER_MANAGEMENT_3, 4, 0),
+SND_SOC_DAPM_ADC("DMIC1L", NULL, WM8996_POWER_MANAGEMENT_3, 3, 0),
+SND_SOC_DAPM_ADC("DMIC1R", NULL, WM8996_POWER_MANAGEMENT_3, 2, 0),
+
+SND_SOC_DAPM_ADC("ADCL", NULL, WM8996_POWER_MANAGEMENT_3, 1, 0),
+SND_SOC_DAPM_ADC("ADCR", NULL, WM8996_POWER_MANAGEMENT_3, 0, 0),
+
+SND_SOC_DAPM_MUX("Left Sidetone", SND_SOC_NOPM, 0, 0, &left_sidetone),
+SND_SOC_DAPM_MUX("Right Sidetone", SND_SOC_NOPM, 0, 0, &right_sidetone),
+
+SND_SOC_DAPM_AIF_IN("DSP2RXL", NULL, 0, WM8996_POWER_MANAGEMENT_3, 11, 0),
+SND_SOC_DAPM_AIF_IN("DSP2RXR", NULL, 1, WM8996_POWER_MANAGEMENT_3, 10, 0),
+SND_SOC_DAPM_AIF_IN("DSP1RXL", NULL, 0, WM8996_POWER_MANAGEMENT_3, 9, 0),
+SND_SOC_DAPM_AIF_IN("DSP1RXR", NULL, 1, WM8996_POWER_MANAGEMENT_3, 8, 0),
+
+SND_SOC_DAPM_MIXER("DSP2TXL", WM8996_POWER_MANAGEMENT_5, 11, 0,
+ dsp2txl, ARRAY_SIZE(dsp2txl)),
+SND_SOC_DAPM_MIXER("DSP2TXR", WM8996_POWER_MANAGEMENT_5, 10, 0,
+ dsp2txr, ARRAY_SIZE(dsp2txr)),
+SND_SOC_DAPM_MIXER("DSP1TXL", WM8996_POWER_MANAGEMENT_5, 9, 0,
+ dsp1txl, ARRAY_SIZE(dsp1txl)),
+SND_SOC_DAPM_MIXER("DSP1TXR", WM8996_POWER_MANAGEMENT_5, 8, 0,
+ dsp1txr, ARRAY_SIZE(dsp1txr)),
+
+SND_SOC_DAPM_MIXER("DAC2L Mixer", SND_SOC_NOPM, 0, 0,
+ dac2l_mix, ARRAY_SIZE(dac2l_mix)),
+SND_SOC_DAPM_MIXER("DAC2R Mixer", SND_SOC_NOPM, 0, 0,
+ dac2r_mix, ARRAY_SIZE(dac2r_mix)),
+SND_SOC_DAPM_MIXER("DAC1L Mixer", SND_SOC_NOPM, 0, 0,
+ dac1l_mix, ARRAY_SIZE(dac1l_mix)),
+SND_SOC_DAPM_MIXER("DAC1R Mixer", SND_SOC_NOPM, 0, 0,
+ dac1r_mix, ARRAY_SIZE(dac1r_mix)),
+
+SND_SOC_DAPM_DAC("DAC2L", NULL, WM8996_POWER_MANAGEMENT_5, 3, 0),
+SND_SOC_DAPM_DAC("DAC2R", NULL, WM8996_POWER_MANAGEMENT_5, 2, 0),
+SND_SOC_DAPM_DAC("DAC1L", NULL, WM8996_POWER_MANAGEMENT_5, 1, 0),
+SND_SOC_DAPM_DAC("DAC1R", NULL, WM8996_POWER_MANAGEMENT_5, 0, 0),
+
+SND_SOC_DAPM_AIF_IN("AIF2RX1", "AIF2 Playback", 1,
+ WM8996_POWER_MANAGEMENT_4, 9, 0),
+SND_SOC_DAPM_AIF_IN("AIF2RX0", "AIF2 Playback", 2,
+ WM8996_POWER_MANAGEMENT_4, 8, 0),
+
+SND_SOC_DAPM_AIF_IN("AIF2TX1", "AIF2 Capture", 1,
+ WM8996_POWER_MANAGEMENT_6, 9, 0),
+SND_SOC_DAPM_AIF_IN("AIF2TX0", "AIF2 Capture", 2,
+ WM8996_POWER_MANAGEMENT_6, 8, 0),
+
+SND_SOC_DAPM_AIF_IN("AIF1RX5", "AIF1 Playback", 5,
+ WM8996_POWER_MANAGEMENT_4, 5, 0),
+SND_SOC_DAPM_AIF_IN("AIF1RX4", "AIF1 Playback", 4,
+ WM8996_POWER_MANAGEMENT_4, 4, 0),
+SND_SOC_DAPM_AIF_IN("AIF1RX3", "AIF1 Playback", 3,
+ WM8996_POWER_MANAGEMENT_4, 3, 0),
+SND_SOC_DAPM_AIF_IN("AIF1RX2", "AIF1 Playback", 2,
+ WM8996_POWER_MANAGEMENT_4, 2, 0),
+SND_SOC_DAPM_AIF_IN("AIF1RX1", "AIF1 Playback", 1,
+ WM8996_POWER_MANAGEMENT_4, 1, 0),
+SND_SOC_DAPM_AIF_IN("AIF1RX0", "AIF1 Playback", 0,
+ WM8996_POWER_MANAGEMENT_4, 0, 0),
+
+SND_SOC_DAPM_AIF_OUT("AIF1TX5", "AIF1 Capture", 5,
+ WM8996_POWER_MANAGEMENT_6, 5, 0),
+SND_SOC_DAPM_AIF_OUT("AIF1TX4", "AIF1 Capture", 4,
+ WM8996_POWER_MANAGEMENT_6, 4, 0),
+SND_SOC_DAPM_AIF_OUT("AIF1TX3", "AIF1 Capture", 3,
+ WM8996_POWER_MANAGEMENT_6, 3, 0),
+SND_SOC_DAPM_AIF_OUT("AIF1TX2", "AIF1 Capture", 2,
+ WM8996_POWER_MANAGEMENT_6, 2, 0),
+SND_SOC_DAPM_AIF_OUT("AIF1TX1", "AIF1 Capture", 1,
+ WM8996_POWER_MANAGEMENT_6, 1, 0),
+SND_SOC_DAPM_AIF_OUT("AIF1TX0", "AIF1 Capture", 0,
+ WM8996_POWER_MANAGEMENT_6, 0, 0),
+
+/* We route as stereo pairs so define some dummy widgets to squash
+ * things down for now. RXA = 0,1, RXB = 2,3 and so on */
+SND_SOC_DAPM_PGA("AIF1RXA", SND_SOC_NOPM, 0, 0, NULL, 0),
+SND_SOC_DAPM_PGA("AIF1RXB", SND_SOC_NOPM, 0, 0, NULL, 0),
+SND_SOC_DAPM_PGA("AIF1RXC", SND_SOC_NOPM, 0, 0, NULL, 0),
+SND_SOC_DAPM_PGA("AIF2RX", SND_SOC_NOPM, 0, 0, NULL, 0),
+SND_SOC_DAPM_PGA("DSP2TX", SND_SOC_NOPM, 0, 0, NULL, 0),
+
+SND_SOC_DAPM_MUX("DSP1RX", SND_SOC_NOPM, 0, 0, &dsp1rx),
+SND_SOC_DAPM_MUX("DSP2RX", SND_SOC_NOPM, 0, 0, &dsp2rx),
+SND_SOC_DAPM_MUX("AIF2TX", SND_SOC_NOPM, 0, 0, &aif2tx),
+
+SND_SOC_DAPM_MUX("SPKL", SND_SOC_NOPM, 0, 0, &spkl_mux),
+SND_SOC_DAPM_MUX("SPKR", SND_SOC_NOPM, 0, 0, &spkr_mux),
+SND_SOC_DAPM_PGA("SPKL PGA", WM8996_LEFT_PDM_SPEAKER, 4, 0, NULL, 0),
+SND_SOC_DAPM_PGA("SPKR PGA", WM8996_RIGHT_PDM_SPEAKER, 4, 0, NULL, 0),
+
+SND_SOC_DAPM_PGA_S("HPOUT2L PGA", 0, WM8996_POWER_MANAGEMENT_1, 7, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2L_DLY", 1, WM8996_ANALOGUE_HP_2, 5, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2L_DCS", 2, WM8996_DC_SERVO_1, 2, 0, dcs_start,
+ SND_SOC_DAPM_POST_PMU),
+SND_SOC_DAPM_PGA_S("HPOUT2L_OUTP", 3, WM8996_ANALOGUE_HP_2, 6, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2L_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT2L, 0,
+ rmv_short_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
+
+SND_SOC_DAPM_PGA_S("HPOUT2R PGA", 0, WM8996_POWER_MANAGEMENT_1, 6, 0,NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2R_DLY", 1, WM8996_ANALOGUE_HP_2, 1, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2R_DCS", 2, WM8996_DC_SERVO_1, 3, 0, dcs_start,
+ SND_SOC_DAPM_POST_PMU),
+SND_SOC_DAPM_PGA_S("HPOUT2R_OUTP", 3, WM8996_ANALOGUE_HP_2, 2, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT2R_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT2R, 0,
+ rmv_short_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
+
+SND_SOC_DAPM_PGA_S("HPOUT1L PGA", 0, WM8996_POWER_MANAGEMENT_1, 5, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1L_DLY", 1, WM8996_ANALOGUE_HP_1, 5, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1L_DCS", 2, WM8996_DC_SERVO_1, 0, 0, dcs_start,
+ SND_SOC_DAPM_POST_PMU),
+SND_SOC_DAPM_PGA_S("HPOUT1L_OUTP", 3, WM8996_ANALOGUE_HP_1, 6, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1L_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT1L, 0,
+ rmv_short_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
+
+SND_SOC_DAPM_PGA_S("HPOUT1R PGA", 0, WM8996_POWER_MANAGEMENT_1, 4, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1R_DLY", 1, WM8996_ANALOGUE_HP_1, 1, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1R_DCS", 2, WM8996_DC_SERVO_1, 1, 0, dcs_start,
+ SND_SOC_DAPM_POST_PMU),
+SND_SOC_DAPM_PGA_S("HPOUT1R_OUTP", 3, WM8996_ANALOGUE_HP_1, 2, 0, NULL, 0),
+SND_SOC_DAPM_PGA_S("HPOUT1R_RMV_SHORT", 3, SND_SOC_NOPM, HPOUT1R, 0,
+ rmv_short_event,
+ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_PRE_PMD),
+
+SND_SOC_DAPM_OUTPUT("HPOUT1L"),
+SND_SOC_DAPM_OUTPUT("HPOUT1R"),
+SND_SOC_DAPM_OUTPUT("HPOUT2L"),
+SND_SOC_DAPM_OUTPUT("HPOUT2R"),
+SND_SOC_DAPM_OUTPUT("SPKDAT"),
+};
+
+static const struct snd_soc_dapm_route wm8996_dapm_routes[] = {
+ { "AIFCLK", NULL, "SYSCLK" },
+ { "SYSDSPCLK", NULL, "SYSCLK" },
+ { "Charge Pump", NULL, "SYSCLK" },
+
+ { "MICB1", NULL, "LDO2" },
+ { "MICB2", NULL, "LDO2" },
+
+ { "IN1L PGA", NULL, "IN2LN" },
+ { "IN1L PGA", NULL, "IN2LP" },
+ { "IN1L PGA", NULL, "IN1LN" },
+ { "IN1L PGA", NULL, "IN1LP" },
+
+ { "IN1R PGA", NULL, "IN2RN" },
+ { "IN1R PGA", NULL, "IN2RP" },
+ { "IN1R PGA", NULL, "IN1RN" },
+ { "IN1R PGA", NULL, "IN1RP" },
+
+ { "ADCL", NULL, "IN1L PGA" },
+
+ { "ADCR", NULL, "IN1R PGA" },
+
+ { "DMIC1L", NULL, "DMIC1DAT" },
+ { "DMIC1R", NULL, "DMIC1DAT" },
+ { "DMIC2L", NULL, "DMIC2DAT" },
+ { "DMIC2R", NULL, "DMIC2DAT" },
+
+ { "DMIC2L", NULL, "DMIC2" },
+ { "DMIC2R", NULL, "DMIC2" },
+ { "DMIC1L", NULL, "DMIC1" },
+ { "DMIC1R", NULL, "DMIC1" },
+
+ { "IN1L Mux", "ADC", "ADCL" },
+ { "IN1L Mux", "DMIC1", "DMIC1L" },
+ { "IN1L Mux", "DMIC2", "DMIC2L" },
+
+ { "IN1R Mux", "ADC", "ADCR" },
+ { "IN1R Mux", "DMIC1", "DMIC1R" },
+ { "IN1R Mux", "DMIC2", "DMIC2R" },
+
+ { "IN2L Mux", "ADC", "ADCL" },
+ { "IN2L Mux", "DMIC1", "DMIC1L" },
+ { "IN2L Mux", "DMIC2", "DMIC2L" },
+
+ { "IN2R Mux", "ADC", "ADCR" },
+ { "IN2R Mux", "DMIC1", "DMIC1R" },
+ { "IN2R Mux", "DMIC2", "DMIC2R" },
+
+ { "Left Sidetone", "IN1", "IN1L Mux" },
+ { "Left Sidetone", "IN2", "IN2L Mux" },
+
+ { "Right Sidetone", "IN1", "IN1R Mux" },
+ { "Right Sidetone", "IN2", "IN2R Mux" },
+
+ { "DSP1TXL", "IN1 Switch", "IN1L Mux" },
+ { "DSP1TXR", "IN1 Switch", "IN1R Mux" },
+
+ { "DSP2TXL", "IN1 Switch", "IN2L Mux" },
+ { "DSP2TXR", "IN1 Switch", "IN2R Mux" },
+
+ { "AIF1TX0", NULL, "DSP1TXL" },
+ { "AIF1TX1", NULL, "DSP1TXR" },
+ { "AIF1TX2", NULL, "DSP2TXL" },
+ { "AIF1TX3", NULL, "DSP2TXR" },
+ { "AIF1TX4", NULL, "AIF2RX0" },
+ { "AIF1TX5", NULL, "AIF2RX1" },
+
+ { "AIF1RX0", NULL, "AIFCLK" },
+ { "AIF1RX1", NULL, "AIFCLK" },
+ { "AIF1RX2", NULL, "AIFCLK" },
+ { "AIF1RX3", NULL, "AIFCLK" },
+ { "AIF1RX4", NULL, "AIFCLK" },
+ { "AIF1RX5", NULL, "AIFCLK" },
+
+ { "AIF2RX0", NULL, "AIFCLK" },
+ { "AIF2RX1", NULL, "AIFCLK" },
+
+ { "DSP1RXL", NULL, "SYSDSPCLK" },
+ { "DSP1RXR", NULL, "SYSDSPCLK" },
+ { "DSP2RXL", NULL, "SYSDSPCLK" },
+ { "DSP2RXR", NULL, "SYSDSPCLK" },
+ { "DSP1TXL", NULL, "SYSDSPCLK" },
+ { "DSP1TXR", NULL, "SYSDSPCLK" },
+ { "DSP2TXL", NULL, "SYSDSPCLK" },
+ { "DSP2TXR", NULL, "SYSDSPCLK" },
+
+ { "AIF1RXA", NULL, "AIF1RX0" },
+ { "AIF1RXA", NULL, "AIF1RX1" },
+ { "AIF1RXB", NULL, "AIF1RX2" },
+ { "AIF1RXB", NULL, "AIF1RX3" },
+ { "AIF1RXC", NULL, "AIF1RX4" },
+ { "AIF1RXC", NULL, "AIF1RX5" },
+
+ { "AIF2RX", NULL, "AIF2RX0" },
+ { "AIF2RX", NULL, "AIF2RX1" },
+
+ { "AIF2TX", "DSP2", "DSP2TX" },
+ { "AIF2TX", "DSP1", "DSP1RX" },
+ { "AIF2TX", "AIF1", "AIF1RXC" },
+
+ { "DSP1RXL", NULL, "DSP1RX" },
+ { "DSP1RXR", NULL, "DSP1RX" },
+ { "DSP2RXL", NULL, "DSP2RX" },
+ { "DSP2RXR", NULL, "DSP2RX" },
+
+ { "DSP2TX", NULL, "DSP2TXL" },
+ { "DSP2TX", NULL, "DSP2TXR" },
+
+ { "DSP1RX", "AIF1", "AIF1RXA" },
+ { "DSP1RX", "AIF2", "AIF2RX" },
+
+ { "DSP2RX", "AIF1", "AIF1RXB" },
+ { "DSP2RX", "AIF2", "AIF2RX" },
+
+ { "DAC2L Mixer", "DSP2 Switch", "DSP2RXL" },
+ { "DAC2L Mixer", "DSP1 Switch", "DSP1RXL" },
+ { "DAC2L Mixer", "Right Sidetone Switch", "Right Sidetone" },
+ { "DAC2L Mixer", "Left Sidetone Switch", "Left Sidetone" },
+
+ { "DAC2R Mixer", "DSP2 Switch", "DSP2RXR" },
+ { "DAC2R Mixer", "DSP1 Switch", "DSP1RXR" },
+ { "DAC2R Mixer", "Right Sidetone Switch", "Right Sidetone" },
+ { "DAC2R Mixer", "Left Sidetone Switch", "Left Sidetone" },
+
+ { "DAC1L Mixer", "DSP2 Switch", "DSP2RXL" },
+ { "DAC1L Mixer", "DSP1 Switch", "DSP1RXL" },
+ { "DAC1L Mixer", "Right Sidetone Switch", "Right Sidetone" },
+ { "DAC1L Mixer", "Left Sidetone Switch", "Left Sidetone" },
+
+ { "DAC1R Mixer", "DSP2 Switch", "DSP2RXR" },
+ { "DAC1R Mixer", "DSP1 Switch", "DSP1RXR" },
+ { "DAC1R Mixer", "Right Sidetone Switch", "Right Sidetone" },
+ { "DAC1R Mixer", "Left Sidetone Switch", "Left Sidetone" },
+
+ { "DAC1L", NULL, "DAC1L Mixer" },
+ { "DAC1R", NULL, "DAC1R Mixer" },
+ { "DAC2L", NULL, "DAC2L Mixer" },
+ { "DAC2R", NULL, "DAC2R Mixer" },
+
+ { "HPOUT2L PGA", NULL, "Charge Pump" },
+ { "HPOUT2L PGA", NULL, "DAC2L" },
+ { "HPOUT2L_DLY", NULL, "HPOUT2L PGA" },
+ { "HPOUT2L_DCS", NULL, "HPOUT2L_DLY" },
+ { "HPOUT2L_OUTP", NULL, "HPOUT2L_DCS" },
+ { "HPOUT2L_RMV_SHORT", NULL, "HPOUT2L_OUTP" },
+
+ { "HPOUT2R PGA", NULL, "Charge Pump" },
+ { "HPOUT2R PGA", NULL, "DAC2R" },
+ { "HPOUT2R_DLY", NULL, "HPOUT2R PGA" },
+ { "HPOUT2R_DCS", NULL, "HPOUT2R_DLY" },
+ { "HPOUT2R_OUTP", NULL, "HPOUT2R_DCS" },
+ { "HPOUT2R_RMV_SHORT", NULL, "HPOUT2R_OUTP" },
+
+ { "HPOUT1L PGA", NULL, "Charge Pump" },
+ { "HPOUT1L PGA", NULL, "DAC1L" },
+ { "HPOUT1L_DLY", NULL, "HPOUT1L PGA" },
+ { "HPOUT1L_DCS", NULL, "HPOUT1L_DLY" },
+ { "HPOUT1L_OUTP", NULL, "HPOUT1L_DCS" },
+ { "HPOUT1L_RMV_SHORT", NULL, "HPOUT1L_OUTP" },
+
+ { "HPOUT1R PGA", NULL, "Charge Pump" },
+ { "HPOUT1R PGA", NULL, "DAC1R" },
+ { "HPOUT1R_DLY", NULL, "HPOUT1R PGA" },
+ { "HPOUT1R_DCS", NULL, "HPOUT1R_DLY" },
+ { "HPOUT1R_OUTP", NULL, "HPOUT1R_DCS" },
+ { "HPOUT1R_RMV_SHORT", NULL, "HPOUT1R_OUTP" },
+
+ { "HPOUT2L", NULL, "HPOUT2L_RMV_SHORT" },
+ { "HPOUT2R", NULL, "HPOUT2R_RMV_SHORT" },
+ { "HPOUT1L", NULL, "HPOUT1L_RMV_SHORT" },
+ { "HPOUT1R", NULL, "HPOUT1R_RMV_SHORT" },
+
+ { "SPKL", "DAC1L", "DAC1L" },
+ { "SPKL", "DAC1R", "DAC1R" },
+ { "SPKL", "DAC2L", "DAC2L" },
+ { "SPKL", "DAC2R", "DAC2R" },
+
+ { "SPKR", "DAC1L", "DAC1L" },
+ { "SPKR", "DAC1R", "DAC1R" },
+ { "SPKR", "DAC2L", "DAC2L" },
+ { "SPKR", "DAC2R", "DAC2R" },
+
+ { "SPKL PGA", NULL, "SPKL" },
+ { "SPKR PGA", NULL, "SPKR" },
+
+ { "SPKDAT", NULL, "SPKL PGA" },
+ { "SPKDAT", NULL, "SPKR PGA" },
+};
+
+static int wm8996_readable_register(struct snd_soc_codec *codec,
+ unsigned int reg)
+{
+ /* Due to the sparseness of the register map the compiler
+ * output from an explicit switch statement ends up being much
+ * more efficient than a table.
+ */
+ switch (reg) {
+ case WM8996_SOFTWARE_RESET:
+ case WM8996_POWER_MANAGEMENT_1:
+ case WM8996_POWER_MANAGEMENT_2:
+ case WM8996_POWER_MANAGEMENT_3:
+ case WM8996_POWER_MANAGEMENT_4:
+ case WM8996_POWER_MANAGEMENT_5:
+ case WM8996_POWER_MANAGEMENT_6:
+ case WM8996_POWER_MANAGEMENT_7:
+ case WM8996_POWER_MANAGEMENT_8:
+ case WM8996_LEFT_LINE_INPUT_VOLUME:
+ case WM8996_RIGHT_LINE_INPUT_VOLUME:
+ case WM8996_LINE_INPUT_CONTROL:
+ case WM8996_DAC1_HPOUT1_VOLUME:
+ case WM8996_DAC2_HPOUT2_VOLUME:
+ case WM8996_DAC1_LEFT_VOLUME:
+ case WM8996_DAC1_RIGHT_VOLUME:
+ case WM8996_DAC2_LEFT_VOLUME:
+ case WM8996_DAC2_RIGHT_VOLUME:
+ case WM8996_OUTPUT1_LEFT_VOLUME:
+ case WM8996_OUTPUT1_RIGHT_VOLUME:
+ case WM8996_OUTPUT2_LEFT_VOLUME:
+ case WM8996_OUTPUT2_RIGHT_VOLUME:
+ case WM8996_MICBIAS_1:
+ case WM8996_MICBIAS_2:
+ case WM8996_LDO_1:
+ case WM8996_LDO_2:
+ case WM8996_ACCESSORY_DETECT_MODE_1:
+ case WM8996_ACCESSORY_DETECT_MODE_2:
+ case WM8996_HEADPHONE_DETECT_1:
+ case WM8996_HEADPHONE_DETECT_2:
+ case WM8996_MIC_DETECT_1:
+ case WM8996_MIC_DETECT_2:
+ case WM8996_MIC_DETECT_3:
+ case WM8996_CHARGE_PUMP_1:
+ case WM8996_CHARGE_PUMP_2:
+ case WM8996_DC_SERVO_1:
+ case WM8996_DC_SERVO_2:
+ case WM8996_DC_SERVO_3:
+ case WM8996_DC_SERVO_5:
+ case WM8996_DC_SERVO_6:
+ case WM8996_DC_SERVO_7:
+ case WM8996_DC_SERVO_READBACK_0:
+ case WM8996_ANALOGUE_HP_1:
+ case WM8996_ANALOGUE_HP_2:
+ case WM8996_CHIP_REVISION:
+ case WM8996_CONTROL_INTERFACE_1:
+ case WM8996_WRITE_SEQUENCER_CTRL_1:
+ case WM8996_WRITE_SEQUENCER_CTRL_2:
+ case WM8996_AIF_CLOCKING_1:
+ case WM8996_AIF_CLOCKING_2:
+ case WM8996_CLOCKING_1:
+ case WM8996_CLOCKING_2:
+ case WM8996_AIF_RATE:
+ case WM8996_FLL_CONTROL_1:
+ case WM8996_FLL_CONTROL_2:
+ case WM8996_FLL_CONTROL_3:
+ case WM8996_FLL_CONTROL_4:
+ case WM8996_FLL_CONTROL_5:
+ case WM8996_FLL_CONTROL_6:
+ case WM8996_FLL_EFS_1:
+ case WM8996_FLL_EFS_2:
+ case WM8996_AIF1_CONTROL:
+ case WM8996_AIF1_BCLK:
+ case WM8996_AIF1_TX_LRCLK_1:
+ case WM8996_AIF1_TX_LRCLK_2:
+ case WM8996_AIF1_RX_LRCLK_1:
+ case WM8996_AIF1_RX_LRCLK_2:
+ case WM8996_AIF1TX_DATA_CONFIGURATION_1:
+ case WM8996_AIF1TX_DATA_CONFIGURATION_2:
+ case WM8996_AIF1RX_DATA_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_0_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_1_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_2_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_3_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_4_CONFIGURATION:
+ case WM8996_AIF1TX_CHANNEL_5_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_0_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_1_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_2_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_3_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_4_CONFIGURATION:
+ case WM8996_AIF1RX_CHANNEL_5_CONFIGURATION:
+ case WM8996_AIF1RX_MONO_CONFIGURATION:
+ case WM8996_AIF1TX_TEST:
+ case WM8996_AIF2_CONTROL:
+ case WM8996_AIF2_BCLK:
+ case WM8996_AIF2_TX_LRCLK_1:
+ case WM8996_AIF2_TX_LRCLK_2:
+ case WM8996_AIF2_RX_LRCLK_1:
+ case WM8996_AIF2_RX_LRCLK_2:
+ case WM8996_AIF2TX_DATA_CONFIGURATION_1:
+ case WM8996_AIF2TX_DATA_CONFIGURATION_2:
+ case WM8996_AIF2RX_DATA_CONFIGURATION:
+ case WM8996_AIF2TX_CHANNEL_0_CONFIGURATION:
+ case WM8996_AIF2TX_CHANNEL_1_CONFIGURATION:
+ case WM8996_AIF2RX_CHANNEL_0_CONFIGURATION:
+ case WM8996_AIF2RX_CHANNEL_1_CONFIGURATION:
+ case WM8996_AIF2RX_MONO_CONFIGURATION:
+ case WM8996_AIF2TX_TEST:
+ case WM8996_DSP1_TX_LEFT_VOLUME:
+ case WM8996_DSP1_TX_RIGHT_VOLUME:
+ case WM8996_DSP1_RX_LEFT_VOLUME:
+ case WM8996_DSP1_RX_RIGHT_VOLUME:
+ case WM8996_DSP1_TX_FILTERS:
+ case WM8996_DSP1_RX_FILTERS_1:
+ case WM8996_DSP1_RX_FILTERS_2:
+ case WM8996_DSP1_DRC_1:
+ case WM8996_DSP1_DRC_2:
+ case WM8996_DSP1_DRC_3:
+ case WM8996_DSP1_DRC_4:
+ case WM8996_DSP1_DRC_5:
+ case WM8996_DSP1_RX_EQ_GAINS_1:
+ case WM8996_DSP1_RX_EQ_GAINS_2:
+ case WM8996_DSP1_RX_EQ_BAND_1_A:
+ case WM8996_DSP1_RX_EQ_BAND_1_B:
+ case WM8996_DSP1_RX_EQ_BAND_1_PG:
+ case WM8996_DSP1_RX_EQ_BAND_2_A:
+ case WM8996_DSP1_RX_EQ_BAND_2_B:
+ case WM8996_DSP1_RX_EQ_BAND_2_C:
+ case WM8996_DSP1_RX_EQ_BAND_2_PG:
+ case WM8996_DSP1_RX_EQ_BAND_3_A:
+ case WM8996_DSP1_RX_EQ_BAND_3_B:
+ case WM8996_DSP1_RX_EQ_BAND_3_C:
+ case WM8996_DSP1_RX_EQ_BAND_3_PG:
+ case WM8996_DSP1_RX_EQ_BAND_4_A:
+ case WM8996_DSP1_RX_EQ_BAND_4_B:
+ case WM8996_DSP1_RX_EQ_BAND_4_C:
+ case WM8996_DSP1_RX_EQ_BAND_4_PG:
+ case WM8996_DSP1_RX_EQ_BAND_5_A:
+ case WM8996_DSP1_RX_EQ_BAND_5_B:
+ case WM8996_DSP1_RX_EQ_BAND_5_PG:
+ case WM8996_DSP2_TX_LEFT_VOLUME:
+ case WM8996_DSP2_TX_RIGHT_VOLUME:
+ case WM8996_DSP2_RX_LEFT_VOLUME:
+ case WM8996_DSP2_RX_RIGHT_VOLUME:
+ case WM8996_DSP2_TX_FILTERS:
+ case WM8996_DSP2_RX_FILTERS_1:
+ case WM8996_DSP2_RX_FILTERS_2:
+ case WM8996_DSP2_DRC_1:
+ case WM8996_DSP2_DRC_2:
+ case WM8996_DSP2_DRC_3:
+ case WM8996_DSP2_DRC_4:
+ case WM8996_DSP2_DRC_5:
+ case WM8996_DSP2_RX_EQ_GAINS_1:
+ case WM8996_DSP2_RX_EQ_GAINS_2:
+ case WM8996_DSP2_RX_EQ_BAND_1_A:
+ case WM8996_DSP2_RX_EQ_BAND_1_B:
+ case WM8996_DSP2_RX_EQ_BAND_1_PG:
+ case WM8996_DSP2_RX_EQ_BAND_2_A:
+ case WM8996_DSP2_RX_EQ_BAND_2_B:
+ case WM8996_DSP2_RX_EQ_BAND_2_C:
+ case WM8996_DSP2_RX_EQ_BAND_2_PG:
+ case WM8996_DSP2_RX_EQ_BAND_3_A:
+ case WM8996_DSP2_RX_EQ_BAND_3_B:
+ case WM8996_DSP2_RX_EQ_BAND_3_C:
+ case WM8996_DSP2_RX_EQ_BAND_3_PG:
+ case WM8996_DSP2_RX_EQ_BAND_4_A:
+ case WM8996_DSP2_RX_EQ_BAND_4_B:
+ case WM8996_DSP2_RX_EQ_BAND_4_C:
+ case WM8996_DSP2_RX_EQ_BAND_4_PG:
+ case WM8996_DSP2_RX_EQ_BAND_5_A:
+ case WM8996_DSP2_RX_EQ_BAND_5_B:
+ case WM8996_DSP2_RX_EQ_BAND_5_PG:
+ case WM8996_DAC1_MIXER_VOLUMES:
+ case WM8996_DAC1_LEFT_MIXER_ROUTING:
+ case WM8996_DAC1_RIGHT_MIXER_ROUTING:
+ case WM8996_DAC2_MIXER_VOLUMES:
+ case WM8996_DAC2_LEFT_MIXER_ROUTING:
+ case WM8996_DAC2_RIGHT_MIXER_ROUTING:
+ case WM8996_DSP1_TX_LEFT_MIXER_ROUTING:
+ case WM8996_DSP1_TX_RIGHT_MIXER_ROUTING:
+ case WM8996_DSP2_TX_LEFT_MIXER_ROUTING:
+ case WM8996_DSP2_TX_RIGHT_MIXER_ROUTING:
+ case WM8996_DSP_TX_MIXER_SELECT:
+ case WM8996_DAC_SOFTMUTE:
+ case WM8996_OVERSAMPLING:
+ case WM8996_SIDETONE:
+ case WM8996_GPIO_1:
+ case WM8996_GPIO_2:
+ case WM8996_GPIO_3:
+ case WM8996_GPIO_4:
+ case WM8996_GPIO_5:
+ case WM8996_PULL_CONTROL_1:
+ case WM8996_PULL_CONTROL_2:
+ case WM8996_INTERRUPT_STATUS_1:
+ case WM8996_INTERRUPT_STATUS_2:
+ case WM8996_INTERRUPT_RAW_STATUS_2:
+ case WM8996_INTERRUPT_STATUS_1_MASK:
+ case WM8996_INTERRUPT_STATUS_2_MASK:
+ case WM8996_INTERRUPT_CONTROL:
+ case WM8996_LEFT_PDM_SPEAKER:
+ case WM8996_RIGHT_PDM_SPEAKER:
+ case WM8996_PDM_SPEAKER_MUTE_SEQUENCE:
+ case WM8996_PDM_SPEAKER_VOLUME:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+static int wm8996_volatile_register(struct snd_soc_codec *codec,
+ unsigned int reg)
+{
+ switch (reg) {
+ case WM8996_SOFTWARE_RESET:
+ case WM8996_CHIP_REVISION:
+ case WM8996_LDO_1:
+ case WM8996_LDO_2:
+ case WM8996_INTERRUPT_STATUS_1:
+ case WM8996_INTERRUPT_STATUS_2:
+ case WM8996_INTERRUPT_RAW_STATUS_2:
+ case WM8996_DC_SERVO_READBACK_0:
+ case WM8996_DC_SERVO_2:
+ case WM8996_DC_SERVO_6:
+ case WM8996_DC_SERVO_7:
+ case WM8996_FLL_CONTROL_6:
+ case WM8996_MIC_DETECT_3:
+ case WM8996_HEADPHONE_DETECT_1:
+ case WM8996_HEADPHONE_DETECT_2:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+static int wm8996_reset(struct snd_soc_codec *codec)
+{
+ return snd_soc_write(codec, WM8996_SOFTWARE_RESET, 0x8915);
+}
+
+static const int bclk_divs[] = {
+ 1, 2, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96
+};
+
+static void wm8996_update_bclk(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int aif, best, cur_val, bclk_rate, bclk_reg, i;
+
+ /* Don't bother if we're in a low frequency idle mode that
+ * can't support audio.
+ */
+ if (wm8996->sysclk < 64000)
+ return;
+
+ for (aif = 0; aif < WM8996_AIFS; aif++) {
+ switch (aif) {
+ case 0:
+ bclk_reg = WM8996_AIF1_BCLK;
+ break;
+ case 1:
+ bclk_reg = WM8996_AIF2_BCLK;
+ break;
+ }
+
+ bclk_rate = wm8996->bclk_rate[aif];
+
+ /* Pick a divisor for BCLK as close as we can get to ideal */
+ best = 0;
+ for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
+ cur_val = (wm8996->sysclk / bclk_divs[i]) - bclk_rate;
+ if (cur_val < 0) /* BCLK table is sorted */
+ break;
+ best = i;
+ }
+ bclk_rate = wm8996->sysclk / bclk_divs[best];
+ dev_dbg(codec->dev, "Using BCLK_DIV %d for actual BCLK %dHz\n",
+ bclk_divs[best], bclk_rate);
+
+ snd_soc_update_bits(codec, bclk_reg,
+ WM8996_AIF1_BCLK_DIV_MASK, best);
+ }
+}
+
+static int wm8996_set_bias_level(struct snd_soc_codec *codec,
+ enum snd_soc_bias_level level)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int ret;
+
+ switch (level) {
+ case SND_SOC_BIAS_ON:
+ break;
+
+ case SND_SOC_BIAS_PREPARE:
+ if (codec->dapm.bias_level == SND_SOC_BIAS_STANDBY) {
+ snd_soc_update_bits(codec, WM8996_POWER_MANAGEMENT_1,
+ WM8996_BG_ENA, WM8996_BG_ENA);
+ msleep(2);
+ }
+ break;
+
+ case SND_SOC_BIAS_STANDBY:
+ if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) {
+ ret = regulator_bulk_enable(ARRAY_SIZE(wm8996->supplies),
+ wm8996->supplies);
+ if (ret != 0) {
+ dev_err(codec->dev,
+ "Failed to enable supplies: %d\n",
+ ret);
+ return ret;
+ }
+
+ if (wm8996->pdata.ldo_ena >= 0) {
+ gpio_set_value_cansleep(wm8996->pdata.ldo_ena,
+ 1);
+ msleep(5);
+ }
+
+ codec->cache_only = false;
+ snd_soc_cache_sync(codec);
+ }
+
+ snd_soc_update_bits(codec, WM8996_POWER_MANAGEMENT_1,
+ WM8996_BG_ENA, 0);
+ break;
+
+ case SND_SOC_BIAS_OFF:
+ codec->cache_only = true;
+ if (wm8996->pdata.ldo_ena >= 0)
+ gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+ regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies),
+ wm8996->supplies);
+ break;
+ }
+
+ codec->dapm.bias_level = level;
+
+ return 0;
+}
+
+static int wm8996_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+ struct snd_soc_codec *codec = dai->codec;
+ int aifctrl = 0;
+ int bclk = 0;
+ int lrclk_tx = 0;
+ int lrclk_rx = 0;
+ int aifctrl_reg, bclk_reg, lrclk_tx_reg, lrclk_rx_reg;
+
+ switch (dai->id) {
+ case 0:
+ aifctrl_reg = WM8996_AIF1_CONTROL;
+ bclk_reg = WM8996_AIF1_BCLK;
+ lrclk_tx_reg = WM8996_AIF1_TX_LRCLK_2;
+ lrclk_rx_reg = WM8996_AIF1_RX_LRCLK_2;
+ break;
+ case 1:
+ aifctrl_reg = WM8996_AIF2_CONTROL;
+ bclk_reg = WM8996_AIF2_BCLK;
+ lrclk_tx_reg = WM8996_AIF2_TX_LRCLK_2;
+ lrclk_rx_reg = WM8996_AIF2_RX_LRCLK_2;
+ break;
+ default:
+ BUG();
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ bclk |= WM8996_AIF1_BCLK_INV;
+ break;
+ case SND_SOC_DAIFMT_NB_IF:
+ lrclk_tx |= WM8996_AIF1TX_LRCLK_INV;
+ lrclk_rx |= WM8996_AIF1RX_LRCLK_INV;
+ break;
+ case SND_SOC_DAIFMT_IB_IF:
+ bclk |= WM8996_AIF1_BCLK_INV;
+ lrclk_tx |= WM8996_AIF1TX_LRCLK_INV;
+ lrclk_rx |= WM8996_AIF1RX_LRCLK_INV;
+ break;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBS_CFS:
+ break;
+ case SND_SOC_DAIFMT_CBS_CFM:
+ lrclk_tx |= WM8996_AIF1TX_LRCLK_MSTR;
+ lrclk_rx |= WM8996_AIF1RX_LRCLK_MSTR;
+ break;
+ case SND_SOC_DAIFMT_CBM_CFS:
+ bclk |= WM8996_AIF1_BCLK_MSTR;
+ break;
+ case SND_SOC_DAIFMT_CBM_CFM:
+ bclk |= WM8996_AIF1_BCLK_MSTR;
+ lrclk_tx |= WM8996_AIF1TX_LRCLK_MSTR;
+ lrclk_rx |= WM8996_AIF1RX_LRCLK_MSTR;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_DSP_A:
+ break;
+ case SND_SOC_DAIFMT_DSP_B:
+ aifctrl |= 1;
+ break;
+ case SND_SOC_DAIFMT_I2S:
+ aifctrl |= 2;
+ break;
+ case SND_SOC_DAIFMT_LEFT_J:
+ aifctrl |= 3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ snd_soc_update_bits(codec, aifctrl_reg, WM8996_AIF1_FMT_MASK, aifctrl);
+ snd_soc_update_bits(codec, bclk_reg,
+ WM8996_AIF1_BCLK_INV | WM8996_AIF1_BCLK_MSTR,
+ bclk);
+ snd_soc_update_bits(codec, lrclk_tx_reg,
+ WM8996_AIF1TX_LRCLK_INV |
+ WM8996_AIF1TX_LRCLK_MSTR,
+ lrclk_tx);
+ snd_soc_update_bits(codec, lrclk_rx_reg,
+ WM8996_AIF1RX_LRCLK_INV |
+ WM8996_AIF1RX_LRCLK_MSTR,
+ lrclk_rx);
+
+ return 0;
+}
+
+static const int dsp_divs[] = {
+ 48000, 32000, 16000, 8000
+};
+
+static int wm8996_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *dai)
+{
+ struct snd_soc_codec *codec = dai->codec;
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int bits, i, bclk_rate;
+ int aifdata = 0;
+ int lrclk = 0;
+ int dsp = 0;
+ int aifdata_reg, lrclk_reg, dsp_shift;
+
+ switch (dai->id) {
+ case 0:
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
+ (snd_soc_read(codec, WM8996_GPIO_1)) & WM8996_GP1_FN_MASK) {
+ aifdata_reg = WM8996_AIF1RX_DATA_CONFIGURATION;
+ lrclk_reg = WM8996_AIF1_RX_LRCLK_1;
+ } else {
+ aifdata_reg = WM8996_AIF1TX_DATA_CONFIGURATION_1;
+ lrclk_reg = WM8996_AIF1_TX_LRCLK_1;
+ }
+ dsp_shift = 0;
+ break;
+ case 1:
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK ||
+ (snd_soc_read(codec, WM8996_GPIO_2)) & WM8996_GP2_FN_MASK) {
+ aifdata_reg = WM8996_AIF2RX_DATA_CONFIGURATION;
+ lrclk_reg = WM8996_AIF2_RX_LRCLK_1;
+ } else {
+ aifdata_reg = WM8996_AIF2TX_DATA_CONFIGURATION_1;
+ lrclk_reg = WM8996_AIF2_TX_LRCLK_1;
+ }
+ dsp_shift = WM8996_DSP2_DIV_SHIFT;
+ break;
+ default:
+ BUG();
+ return -EINVAL;
+ }
+
+ bclk_rate = snd_soc_params_to_bclk(params);
+ if (bclk_rate < 0) {
+ dev_err(codec->dev, "Unsupported BCLK rate: %d\n", bclk_rate);
+ return bclk_rate;
+ }
+
+ wm8996->bclk_rate[dai->id] = bclk_rate;
+ wm8996->rx_rate[dai->id] = params_rate(params);
+
+ /* Needs looking at for TDM */
+ bits = snd_pcm_format_width(params_format(params));
+ if (bits < 0)
+ return bits;
+ aifdata |= (bits << WM8996_AIF1TX_WL_SHIFT) | bits;
+
+ for (i = 0; i < ARRAY_SIZE(dsp_divs); i++) {
+ if (dsp_divs[i] == params_rate(params))
+ break;
+ }
+ if (i == ARRAY_SIZE(dsp_divs)) {
+ dev_err(codec->dev, "Unsupported sample rate %dHz\n",
+ params_rate(params));
+ return -EINVAL;
+ }
+ dsp |= i << dsp_shift;
+
+ wm8996_update_bclk(codec);
+
+ lrclk = bclk_rate / params_rate(params);
+ dev_dbg(dai->dev, "Using LRCLK rate %d for actual LRCLK %dHz\n",
+ lrclk, bclk_rate / lrclk);
+
+ snd_soc_update_bits(codec, aifdata_reg,
+ WM8996_AIF1TX_WL_MASK |
+ WM8996_AIF1TX_SLOT_LEN_MASK,
+ aifdata);
+ snd_soc_update_bits(codec, lrclk_reg, WM8996_AIF1RX_RATE_MASK,
+ lrclk);
+ snd_soc_update_bits(codec, WM8996_AIF_CLOCKING_2,
+ WM8996_DSP1_DIV_SHIFT << dsp_shift, dsp);
+
+ return 0;
+}
+
+static int wm8996_set_sysclk(struct snd_soc_dai *dai,
+ int clk_id, unsigned int freq, int dir)
+{
+ struct snd_soc_codec *codec = dai->codec;
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int lfclk = 0;
+ int ratediv = 0;
+ int src;
+ int old;
+
+ if (freq == wm8996->sysclk && clk_id == wm8996->sysclk_src)
+ return 0;
+
+ /* Disable SYSCLK while we reconfigure */
+ old = snd_soc_read(codec, WM8996_AIF_CLOCKING_1) & WM8996_SYSCLK_ENA;
+ snd_soc_update_bits(codec, WM8996_AIF_CLOCKING_1,
+ WM8996_SYSCLK_ENA, 0);
+
+ switch (clk_id) {
+ case WM8996_SYSCLK_MCLK1:
+ wm8996->sysclk = freq;
+ src = 0;
+ break;
+ case WM8996_SYSCLK_MCLK2:
+ wm8996->sysclk = freq;
+ src = 1;
+ break;
+ case WM8996_SYSCLK_FLL:
+ wm8996->sysclk = freq;
+ src = 2;
+ break;
+ default:
+ dev_err(codec->dev, "Unsupported clock source %d\n", clk_id);
+ return -EINVAL;
+ }
+
+ switch (wm8996->sysclk) {
+ case 6144000:
+ snd_soc_update_bits(codec, WM8996_AIF_RATE,
+ WM8996_SYSCLK_RATE, 0);
+ break;
+ case 24576000:
+ ratediv = WM8996_SYSCLK_DIV;
+ case 12288000:
+ snd_soc_update_bits(codec, WM8996_AIF_RATE,
+ WM8996_SYSCLK_RATE, WM8996_SYSCLK_RATE);
+ break;
+ case 32000:
+ case 32768:
+ lfclk = WM8996_LFCLK_ENA;
+ break;
+ default:
+ dev_warn(codec->dev, "Unsupported clock rate %dHz\n",
+ wm8996->sysclk);
+ return -EINVAL;
+ }
+
+ wm8996_update_bclk(codec);
+
+ snd_soc_update_bits(codec, WM8996_AIF_CLOCKING_1,
+ WM8996_SYSCLK_SRC_MASK | WM8996_SYSCLK_DIV_MASK,
+ src << WM8996_SYSCLK_SRC_SHIFT | ratediv);
+ snd_soc_update_bits(codec, WM8996_CLOCKING_1, WM8996_LFCLK_ENA, lfclk);
+ snd_soc_update_bits(codec, WM8996_AIF_CLOCKING_1,
+ WM8996_SYSCLK_ENA, old);
+
+ wm8996->sysclk_src = clk_id;
+
+ return 0;
+}
+
+struct _fll_div {
+ u16 fll_fratio;
+ u16 fll_outdiv;
+ u16 fll_refclk_div;
+ u16 fll_loop_gain;
+ u16 fll_ref_freq;
+ u16 n;
+ u16 theta;
+ u16 lambda;
+};
+
+static struct {
+ unsigned int min;
+ unsigned int max;
+ u16 fll_fratio;
+ int ratio;
+} fll_fratios[] = {
+ { 0, 64000, 4, 16 },
+ { 64000, 128000, 3, 8 },
+ { 128000, 256000, 2, 4 },
+ { 256000, 1000000, 1, 2 },
+ { 1000000, 13500000, 0, 1 },
+};
+
+static int fll_factors(struct _fll_div *fll_div, unsigned int Fref,
+ unsigned int Fout)
+{
+ unsigned int target;
+ unsigned int div;
+ unsigned int fratio, gcd_fll;
+ int i;
+
+ /* Fref must be <=13.5MHz */
+ div = 1;
+ fll_div->fll_refclk_div = 0;
+ while ((Fref / div) > 13500000) {
+ div *= 2;
+ fll_div->fll_refclk_div++;
+
+ if (div > 8) {
+ pr_err("Can't scale %dMHz input down to <=13.5MHz\n",
+ Fref);
+ return -EINVAL;
+ }
+ }
+
+ pr_debug("FLL Fref=%u Fout=%u\n", Fref, Fout);
+
+ /* Apply the division for our remaining calculations */
+ Fref /= div;
+
+ if (Fref >= 3000000)
+ fll_div->fll_loop_gain = 5;
+ else
+ fll_div->fll_loop_gain = 0;
+
+ if (Fref >= 48000)
+ fll_div->fll_ref_freq = 0;
+ else
+ fll_div->fll_ref_freq = 1;
+
+ /* Fvco should be 90-100MHz; don't check the upper bound */
+ div = 2;
+ while (Fout * div < 90000000) {
+ div++;
+ if (div > 64) {
+ pr_err("Unable to find FLL_OUTDIV for Fout=%uHz\n",
+ Fout);
+ return -EINVAL;
+ }
+ }
+ target = Fout * div;
+ fll_div->fll_outdiv = div - 1;
+
+ pr_debug("FLL Fvco=%dHz\n", target);
+
+ /* Find an appropraite FLL_FRATIO and factor it out of the target */
+ for (i = 0; i < ARRAY_SIZE(fll_fratios); i++) {
+ if (fll_fratios[i].min <= Fref && Fref <= fll_fratios[i].max) {
+ fll_div->fll_fratio = fll_fratios[i].fll_fratio;
+ fratio = fll_fratios[i].ratio;
+ break;
+ }
+ }
+ if (i == ARRAY_SIZE(fll_fratios)) {
+ pr_err("Unable to find FLL_FRATIO for Fref=%uHz\n", Fref);
+ return -EINVAL;
+ }
+
+ fll_div->n = target / (fratio * Fref);
+
+ if (target % Fref == 0) {
+ fll_div->theta = 0;
+ fll_div->lambda = 0;
+ } else {
+ gcd_fll = gcd(target, fratio * Fref);
+
+ fll_div->theta = (target - (fll_div->n * fratio * Fref))
+ / gcd_fll;
+ fll_div->lambda = (fratio * Fref) / gcd_fll;
+ }
+
+ pr_debug("FLL N=%x THETA=%x LAMBDA=%x\n",
+ fll_div->n, fll_div->theta, fll_div->lambda);
+ pr_debug("FLL_FRATIO=%x FLL_OUTDIV=%x FLL_REFCLK_DIV=%x\n",
+ fll_div->fll_fratio, fll_div->fll_outdiv,
+ fll_div->fll_refclk_div);
+
+ return 0;
+}
+
+static int wm8996_set_fll(struct snd_soc_codec *codec, int fll_id, int source,
+ unsigned int Fref, unsigned int Fout)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct i2c_client *i2c = to_i2c_client(codec->dev);
+ struct _fll_div fll_div;
+ unsigned long timeout;
+ int ret, reg;
+
+ /* Any change? */
+ if (source == wm8996->fll_src && Fref == wm8996->fll_fref &&
+ Fout == wm8996->fll_fout)
+ return 0;
+
+ if (Fout == 0) {
+ dev_dbg(codec->dev, "FLL disabled\n");
+
+ wm8996->fll_fref = 0;
+ wm8996->fll_fout = 0;
+
+ snd_soc_update_bits(codec, WM8996_FLL_CONTROL_1,
+ WM8996_FLL_ENA, 0);
+
+ return 0;
+ }
+
+ ret = fll_factors(&fll_div, Fref, Fout);
+ if (ret != 0)
+ return ret;
+
+ switch (source) {
+ case WM8996_FLL_MCLK1:
+ reg = 0;
+ break;
+ case WM8996_FLL_MCLK2:
+ reg = 1;
+ break;
+ case WM8996_FLL_DACLRCLK1:
+ reg = 2;
+ break;
+ case WM8996_FLL_BCLK1:
+ reg = 3;
+ break;
+ default:
+ dev_err(codec->dev, "Unknown FLL source %d\n", ret);
+ return -EINVAL;
+ }
+
+ reg |= fll_div.fll_refclk_div << WM8996_FLL_REFCLK_DIV_SHIFT;
+ reg |= fll_div.fll_ref_freq << WM8996_FLL_REF_FREQ_SHIFT;
+
+ snd_soc_update_bits(codec, WM8996_FLL_CONTROL_5,
+ WM8996_FLL_REFCLK_DIV_MASK | WM8996_FLL_REF_FREQ |
+ WM8996_FLL_REFCLK_SRC_MASK, reg);
+
+ reg = 0;
+ if (fll_div.theta || fll_div.lambda)
+ reg |= WM8996_FLL_EFS_ENA | (3 << WM8996_FLL_LFSR_SEL_SHIFT);
+ else
+ reg |= 1 << WM8996_FLL_LFSR_SEL_SHIFT;
+ snd_soc_write(codec, WM8996_FLL_EFS_2, reg);
+
+ snd_soc_update_bits(codec, WM8996_FLL_CONTROL_2,
+ WM8996_FLL_OUTDIV_MASK |
+ WM8996_FLL_FRATIO_MASK,
+ (fll_div.fll_outdiv << WM8996_FLL_OUTDIV_SHIFT) |
+ (fll_div.fll_fratio));
+
+ snd_soc_write(codec, WM8996_FLL_CONTROL_3, fll_div.theta);
+
+ snd_soc_update_bits(codec, WM8996_FLL_CONTROL_4,
+ WM8996_FLL_N_MASK | WM8996_FLL_LOOP_GAIN_MASK,
+ (fll_div.n << WM8996_FLL_N_SHIFT) |
+ fll_div.fll_loop_gain);
+
+ snd_soc_write(codec, WM8996_FLL_EFS_1, fll_div.lambda);
+
+ snd_soc_update_bits(codec, WM8996_FLL_CONTROL_1,
+ WM8996_FLL_ENA, WM8996_FLL_ENA);
+
+ /* The FLL supports live reconfiguration - kick that in case we were
+ * already enabled.
+ */
+ snd_soc_write(codec, WM8996_FLL_CONTROL_6, WM8996_FLL_SWITCH_CLK);
+
+ /* Wait for the FLL to lock, using the interrupt if possible */
+ if (Fref > 1000000)
+ timeout = usecs_to_jiffies(300);
+ else
+ timeout = msecs_to_jiffies(2);
+
+ /* Allow substantially longer if we've actually got the IRQ */
+ if (i2c->irq)
+ timeout *= 1000;
+
+ ret = wait_for_completion_timeout(&wm8996->fll_lock, timeout);
+
+ if (ret == 0 && i2c->irq) {
+ dev_err(codec->dev, "Timed out waiting for FLL\n");
+ ret = -ETIMEDOUT;
+ } else {
+ ret = 0;
+ }
+
+ dev_dbg(codec->dev, "FLL configured for %dHz->%dHz\n", Fref, Fout);
+
+ wm8996->fll_fref = Fref;
+ wm8996->fll_fout = Fout;
+ wm8996->fll_src = source;
+
+ return ret;
+}
+
+#ifdef CONFIG_GPIOLIB
+static inline struct wm8996_priv *gpio_to_wm8996(struct gpio_chip *chip)
+{
+ return container_of(chip, struct wm8996_priv, gpio_chip);
+}
+
+static void wm8996_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+ struct snd_soc_codec *codec = wm8996->codec;
+
+ snd_soc_update_bits(codec, WM8996_GPIO_1 + offset,
+ WM8996_GP1_LVL, !!value << WM8996_GP1_LVL_SHIFT);
+}
+
+static int wm8996_gpio_direction_out(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+ struct snd_soc_codec *codec = wm8996->codec;
+ int val;
+
+ val = (1 << WM8996_GP1_FN_SHIFT) | (!!value << WM8996_GP1_LVL_SHIFT);
+
+ return snd_soc_update_bits(codec, WM8996_GPIO_1 + offset,
+ WM8996_GP1_FN_MASK | WM8996_GP1_DIR |
+ WM8996_GP1_LVL, val);
+}
+
+static int wm8996_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+ struct snd_soc_codec *codec = wm8996->codec;
+ int ret;
+
+ ret = snd_soc_read(codec, WM8996_GPIO_1 + offset);
+ if (ret < 0)
+ return ret;
+
+ return (ret & WM8996_GP1_LVL) != 0;
+}
+
+static int wm8996_gpio_direction_in(struct gpio_chip *chip, unsigned offset)
+{
+ struct wm8996_priv *wm8996 = gpio_to_wm8996(chip);
+ struct snd_soc_codec *codec = wm8996->codec;
+
+ return snd_soc_update_bits(codec, WM8996_GPIO_1 + offset,
+ WM8996_GP1_FN_MASK | WM8996_GP1_DIR,
+ (1 << WM8996_GP1_FN_SHIFT) |
+ (1 << WM8996_GP1_DIR_SHIFT));
+}
+
+static struct gpio_chip wm8996_template_chip = {
+ .label = "wm8996",
+ .owner = THIS_MODULE,
+ .direction_output = wm8996_gpio_direction_out,
+ .set = wm8996_gpio_set,
+ .direction_input = wm8996_gpio_direction_in,
+ .get = wm8996_gpio_get,
+ .can_sleep = 1,
+};
+
+static void wm8996_init_gpio(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int ret;
+
+ wm8996->gpio_chip = wm8996_template_chip;
+ wm8996->gpio_chip.ngpio = 5;
+ wm8996->gpio_chip.dev = codec->dev;
+
+ if (wm8996->pdata.gpio_base)
+ wm8996->gpio_chip.base = wm8996->pdata.gpio_base;
+ else
+ wm8996->gpio_chip.base = -1;
+
+ ret = gpiochip_add(&wm8996->gpio_chip);
+ if (ret != 0)
+ dev_err(codec->dev, "Failed to add GPIOs: %d\n", ret);
+}
+
+static void wm8996_free_gpio(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int ret;
+
+ ret = gpiochip_remove(&wm8996->gpio_chip);
+ if (ret != 0)
+ dev_err(codec->dev, "Failed to remove GPIOs: %d\n", ret);
+}
+#else
+static void wm8996_init_gpio(struct snd_soc_codec *codec)
+{
+}
+
+static void wm8996_free_gpio(struct snd_soc_codec *codec)
+{
+}
+#endif
+
+/**
+ * wm8996_detect - Enable default WM8996 jack detection
+ *
+ * The WM8996 has advanced accessory detection support for headsets.
+ * This function provides a default implementation which integrates
+ * the majority of this functionality with minimal user configuration.
+ *
+ * This will detect headset, headphone and short circuit button and
+ * will also detect inverted microphone ground connections and update
+ * the polarity of the connections.
+ */
+int wm8996_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack,
+ wm8996_polarity_fn polarity_cb)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+
+ wm8996->jack = jack;
+ wm8996->detecting = true;
+ wm8996->polarity_cb = polarity_cb;
+
+ if (wm8996->polarity_cb)
+ wm8996->polarity_cb(codec, 0);
+
+ /* Clear discarge to avoid noise during detection */
+ snd_soc_update_bits(codec, WM8996_MICBIAS_1,
+ WM8996_MICB1_DISCH, 0);
+ snd_soc_update_bits(codec, WM8996_MICBIAS_2,
+ WM8996_MICB2_DISCH, 0);
+
+ /* LDO2 powers the microphones, SYSCLK clocks detection */
+ snd_soc_dapm_force_enable_pin(&codec->dapm, "LDO2");
+ snd_soc_dapm_force_enable_pin(&codec->dapm, "SYSCLK");
+
+ /* We start off just enabling microphone detection - even a
+ * plain headphone will trigger detection.
+ */
+ snd_soc_update_bits(codec, WM8996_MIC_DETECT_1,
+ WM8996_MICD_ENA, WM8996_MICD_ENA);
+
+ /* Slowest detection rate, gives debounce for initial detection */
+ snd_soc_update_bits(codec, WM8996_MIC_DETECT_1,
+ WM8996_MICD_RATE_MASK,
+ WM8996_MICD_RATE_MASK);
+
+ /* Enable interrupts and we're off */
+ snd_soc_update_bits(codec, WM8996_INTERRUPT_STATUS_2_MASK,
+ WM8996_IM_MICD_EINT, 0);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(wm8996_detect);
+
+static void wm8996_micd(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int val, reg;
+
+ val = snd_soc_read(codec, WM8996_MIC_DETECT_3);
+
+ dev_dbg(codec->dev, "Microphone event: %x\n", val);
+
+ if (!(val & WM8996_MICD_VALID)) {
+ dev_warn(codec->dev, "Microphone detection state invalid\n");
+ return;
+ }
+
+ /* No accessory, reset everything and report removal */
+ if (!(val & WM8996_MICD_STS)) {
+ dev_dbg(codec->dev, "Jack removal detected\n");
+ wm8996->jack_mic = false;
+ wm8996->detecting = true;
+ snd_soc_jack_report(wm8996->jack, 0,
+ SND_JACK_HEADSET | SND_JACK_BTN_0);
+ snd_soc_update_bits(codec, WM8996_MIC_DETECT_1,
+ WM8996_MICD_RATE_MASK,
+ WM8996_MICD_RATE_MASK);
+ return;
+ }
+
+ /* If the measurement is very high we've got a microphone but
+ * do a little debounce to account for mechanical issues.
+ */
+ if (val & 0x400) {
+ dev_dbg(codec->dev, "Microphone detected\n");
+ snd_soc_jack_report(wm8996->jack, SND_JACK_HEADSET,
+ SND_JACK_HEADSET | SND_JACK_BTN_0);
+ wm8996->jack_mic = true;
+ wm8996->detecting = false;
+
+ /* Increase poll rate to give better responsiveness
+ * for buttons */
+ snd_soc_update_bits(codec, WM8996_MIC_DETECT_1,
+ WM8996_MICD_RATE_MASK,
+ 5 << WM8996_MICD_RATE_SHIFT);
+ }
+
+ /* If we detected a lower impedence during initial startup
+ * then we probably have the wrong polarity, flip it. Don't
+ * do this for the lowest impedences to speed up detection of
+ * plain headphones.
+ */
+ if (wm8996->detecting && (val & 0x3f0)) {
+ reg = snd_soc_read(codec, WM8996_ACCESSORY_DETECT_MODE_2);
+ reg ^= WM8996_HPOUT1FB_SRC | WM8996_MICD_SRC |
+ WM8996_MICD_BIAS_SRC;
+ snd_soc_update_bits(codec, WM8996_ACCESSORY_DETECT_MODE_2,
+ WM8996_HPOUT1FB_SRC | WM8996_MICD_SRC |
+ WM8996_MICD_BIAS_SRC, reg);
+
+ if (wm8996->polarity_cb)
+ wm8996->polarity_cb(codec,
+ (reg & WM8996_MICD_SRC) != 0);
+
+ dev_dbg(codec->dev, "Set microphone polarity to %d\n",
+ (reg & WM8996_MICD_SRC) != 0);
+
+ return;
+ }
+
+ /* Don't distinguish between buttons, just report any low
+ * impedence as BTN_0.
+ */
+ if (val & 0x3fc) {
+ if (wm8996->jack_mic) {
+ dev_dbg(codec->dev, "Mic button detected\n");
+ snd_soc_jack_report(wm8996->jack,
+ SND_JACK_HEADSET | SND_JACK_BTN_0,
+ SND_JACK_HEADSET | SND_JACK_BTN_0);
+ } else {
+ dev_dbg(codec->dev, "Headphone detected\n");
+ snd_soc_jack_report(wm8996->jack,
+ SND_JACK_HEADPHONE,
+ SND_JACK_HEADSET |
+ SND_JACK_BTN_0);
+
+ /* Increase the detection rate a bit for
+ * responsiveness.
+ */
+ snd_soc_update_bits(codec, WM8996_MIC_DETECT_1,
+ WM8996_MICD_RATE_MASK,
+ 7 << WM8996_MICD_RATE_SHIFT);
+
+ wm8996->detecting = false;
+ }
+ }
+}
+
+static irqreturn_t wm8996_irq(int irq, void *data)
+{
+ struct snd_soc_codec *codec = data;
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ int irq_val;
+
+ irq_val = snd_soc_read(codec, WM8996_INTERRUPT_STATUS_2);
+ if (irq_val < 0) {
+ dev_err(codec->dev, "Failed to read IRQ status: %d\n",
+ irq_val);
+ return IRQ_NONE;
+ }
+ irq_val &= ~snd_soc_read(codec, WM8996_INTERRUPT_STATUS_2_MASK);
+
+ snd_soc_write(codec, WM8996_INTERRUPT_STATUS_2, irq_val);
+
+ if (irq_val & (WM8996_DCS_DONE_01_EINT | WM8996_DCS_DONE_23_EINT)) {
+ dev_dbg(codec->dev, "DC servo IRQ\n");
+ complete(&wm8996->dcs_done);
+ }
+
+ if (irq_val & WM8996_FIFOS_ERR_EINT)
+ dev_err(codec->dev, "Digital core FIFO error\n");
+
+ if (irq_val & WM8996_FLL_LOCK_EINT) {
+ dev_dbg(codec->dev, "FLL locked\n");
+ complete(&wm8996->fll_lock);
+ }
+
+ if (irq_val & WM8996_MICD_EINT)
+ wm8996_micd(codec);
+
+ if (irq_val)
+ return IRQ_HANDLED;
+ else
+ return IRQ_NONE;
+}
+
+static irqreturn_t wm8996_edge_irq(int irq, void *data)
+{
+ irqreturn_t ret = IRQ_NONE;
+ irqreturn_t val;
+
+ do {
+ val = wm8996_irq(irq, data);
+ if (val != IRQ_NONE)
+ ret = val;
+ } while (val != IRQ_NONE);
+
+ return ret;
+}
+
+static void wm8996_retune_mobile_pdata(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct wm8996_pdata *pdata = &wm8996->pdata;
+
+ struct snd_kcontrol_new controls[] = {
+ SOC_ENUM_EXT("DSP1 EQ Mode",
+ wm8996->retune_mobile_enum,
+ wm8996_get_retune_mobile_enum,
+ wm8996_put_retune_mobile_enum),
+ SOC_ENUM_EXT("DSP2 EQ Mode",
+ wm8996->retune_mobile_enum,
+ wm8996_get_retune_mobile_enum,
+ wm8996_put_retune_mobile_enum),
+ };
+ int ret, i, j;
+ const char **t;
+
+ /* We need an array of texts for the enum API but the number
+ * of texts is likely to be less than the number of
+ * configurations due to the sample rate dependency of the
+ * configurations. */
+ wm8996->num_retune_mobile_texts = 0;
+ wm8996->retune_mobile_texts = NULL;
+ for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
+ for (j = 0; j < wm8996->num_retune_mobile_texts; j++) {
+ if (strcmp(pdata->retune_mobile_cfgs[i].name,
+ wm8996->retune_mobile_texts[j]) == 0)
+ break;
+ }
+
+ if (j != wm8996->num_retune_mobile_texts)
+ continue;
+
+ /* Expand the array... */
+ t = krealloc(wm8996->retune_mobile_texts,
+ sizeof(char *) *
+ (wm8996->num_retune_mobile_texts + 1),
+ GFP_KERNEL);
+ if (t == NULL)
+ continue;
+
+ /* ...store the new entry... */
+ t[wm8996->num_retune_mobile_texts] =
+ pdata->retune_mobile_cfgs[i].name;
+
+ /* ...and remember the new version. */
+ wm8996->num_retune_mobile_texts++;
+ wm8996->retune_mobile_texts = t;
+ }
+
+ dev_dbg(codec->dev, "Allocated %d unique ReTune Mobile names\n",
+ wm8996->num_retune_mobile_texts);
+
+ wm8996->retune_mobile_enum.max = wm8996->num_retune_mobile_texts;
+ wm8996->retune_mobile_enum.texts = wm8996->retune_mobile_texts;
+
+ ret = snd_soc_add_controls(codec, controls, ARRAY_SIZE(controls));
+ if (ret != 0)
+ dev_err(codec->dev,
+ "Failed to add ReTune Mobile controls: %d\n", ret);
+}
+
+static int wm8996_probe(struct snd_soc_codec *codec)
+{
+ int ret;
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct i2c_client *i2c = to_i2c_client(codec->dev);
+ struct snd_soc_dapm_context *dapm = &codec->dapm;
+ int i, irq_flags;
+
+ wm8996->codec = codec;
+
+ init_completion(&wm8996->dcs_done);
+ init_completion(&wm8996->fll_lock);
+
+ dapm->idle_bias_off = true;
+ dapm->bias_level = SND_SOC_BIAS_OFF;
+
+ ret = snd_soc_codec_set_cache_io(codec, 16, 16, SND_SOC_I2C);
+ if (ret != 0) {
+ dev_err(codec->dev, "Failed to set cache I/O: %d\n", ret);
+ goto err;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(wm8996->supplies); i++)
+ wm8996->supplies[i].supply = wm8996_supply_names[i];
+
+ ret = regulator_bulk_get(codec->dev, ARRAY_SIZE(wm8996->supplies),
+ wm8996->supplies);
+ if (ret != 0) {
+ dev_err(codec->dev, "Failed to request supplies: %d\n", ret);
+ goto err;
+ }
+
+ wm8996->disable_nb[0].notifier_call = wm8996_regulator_event_0;
+ wm8996->disable_nb[1].notifier_call = wm8996_regulator_event_1;
+ wm8996->disable_nb[2].notifier_call = wm8996_regulator_event_2;
+ wm8996->disable_nb[3].notifier_call = wm8996_regulator_event_3;
+
+ /* This should really be moved into the regulator core */
+ for (i = 0; i < ARRAY_SIZE(wm8996->supplies); i++) {
+ ret = regulator_register_notifier(wm8996->supplies[i].consumer,
+ &wm8996->disable_nb[i]);
+ if (ret != 0) {
+ dev_err(codec->dev,
+ "Failed to register regulator notifier: %d\n",
+ ret);
+ }
+ }
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(wm8996->supplies),
+ wm8996->supplies);
+ if (ret != 0) {
+ dev_err(codec->dev, "Failed to enable supplies: %d\n", ret);
+ goto err_get;
+ }
+
+ if (wm8996->pdata.ldo_ena >= 0) {
+ gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 1);
+ msleep(5);
+ }
+
+ ret = snd_soc_read(codec, WM8996_SOFTWARE_RESET);
+ if (ret < 0) {
+ dev_err(codec->dev, "Failed to read ID register: %d\n", ret);
+ goto err_enable;
+ }
+ if (ret != 0x8915) {
+ dev_err(codec->dev, "Device is not a WM8996, ID %x\n", ret);
+ ret = -EINVAL;
+ goto err_enable;
+ }
+
+ ret = snd_soc_read(codec, WM8996_CHIP_REVISION);
+ if (ret < 0) {
+ dev_err(codec->dev, "Failed to read device revision: %d\n",
+ ret);
+ goto err_enable;
+ }
+
+ dev_info(codec->dev, "revision %c\n",
+ (ret & WM8996_CHIP_REV_MASK) + 'A');
+
+ if (wm8996->pdata.ldo_ena >= 0) {
+ gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+ } else {
+ ret = wm8996_reset(codec);
+ if (ret < 0) {
+ dev_err(codec->dev, "Failed to issue reset\n");
+ goto err_enable;
+ }
+ }
+
+ codec->cache_only = true;
+
+ /* Apply platform data settings */
+ snd_soc_update_bits(codec, WM8996_LINE_INPUT_CONTROL,
+ WM8996_INL_MODE_MASK | WM8996_INR_MODE_MASK,
+ wm8996->pdata.inl_mode << WM8996_INL_MODE_SHIFT |
+ wm8996->pdata.inr_mode);
+
+ for (i = 0; i < ARRAY_SIZE(wm8996->pdata.gpio_default); i++) {
+ if (!wm8996->pdata.gpio_default[i])
+ continue;
+
+ snd_soc_write(codec, WM8996_GPIO_1 + i,
+ wm8996->pdata.gpio_default[i] & 0xffff);
+ }
+
+ if (wm8996->pdata.spkmute_seq)
+ snd_soc_update_bits(codec, WM8996_PDM_SPEAKER_MUTE_SEQUENCE,
+ WM8996_SPK_MUTE_ENDIAN |
+ WM8996_SPK_MUTE_SEQ1_MASK,
+ wm8996->pdata.spkmute_seq);
+
+ snd_soc_update_bits(codec, WM8996_ACCESSORY_DETECT_MODE_2,
+ WM8996_MICD_BIAS_SRC | WM8996_HPOUT1FB_SRC |
+ WM8996_MICD_SRC, wm8996->pdata.micdet_def);
+
+ /* Latch volume update bits */
+ snd_soc_update_bits(codec, WM8996_LEFT_LINE_INPUT_VOLUME,
+ WM8996_IN1_VU, WM8996_IN1_VU);
+ snd_soc_update_bits(codec, WM8996_RIGHT_LINE_INPUT_VOLUME,
+ WM8996_IN1_VU, WM8996_IN1_VU);
+
+ snd_soc_update_bits(codec, WM8996_DAC1_LEFT_VOLUME,
+ WM8996_DAC1_VU, WM8996_DAC1_VU);
+ snd_soc_update_bits(codec, WM8996_DAC1_RIGHT_VOLUME,
+ WM8996_DAC1_VU, WM8996_DAC1_VU);
+ snd_soc_update_bits(codec, WM8996_DAC2_LEFT_VOLUME,
+ WM8996_DAC2_VU, WM8996_DAC2_VU);
+ snd_soc_update_bits(codec, WM8996_DAC2_RIGHT_VOLUME,
+ WM8996_DAC2_VU, WM8996_DAC2_VU);
+
+ snd_soc_update_bits(codec, WM8996_OUTPUT1_LEFT_VOLUME,
+ WM8996_DAC1_VU, WM8996_DAC1_VU);
+ snd_soc_update_bits(codec, WM8996_OUTPUT1_RIGHT_VOLUME,
+ WM8996_DAC1_VU, WM8996_DAC1_VU);
+ snd_soc_update_bits(codec, WM8996_OUTPUT2_LEFT_VOLUME,
+ WM8996_DAC2_VU, WM8996_DAC2_VU);
+ snd_soc_update_bits(codec, WM8996_OUTPUT2_RIGHT_VOLUME,
+ WM8996_DAC2_VU, WM8996_DAC2_VU);
+
+ snd_soc_update_bits(codec, WM8996_DSP1_TX_LEFT_VOLUME,
+ WM8996_DSP1TX_VU, WM8996_DSP1TX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP1_TX_RIGHT_VOLUME,
+ WM8996_DSP1TX_VU, WM8996_DSP1TX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP2_TX_LEFT_VOLUME,
+ WM8996_DSP2TX_VU, WM8996_DSP2TX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP2_TX_RIGHT_VOLUME,
+ WM8996_DSP2TX_VU, WM8996_DSP2TX_VU);
+
+ snd_soc_update_bits(codec, WM8996_DSP1_RX_LEFT_VOLUME,
+ WM8996_DSP1RX_VU, WM8996_DSP1RX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP1_RX_RIGHT_VOLUME,
+ WM8996_DSP1RX_VU, WM8996_DSP1RX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP2_RX_LEFT_VOLUME,
+ WM8996_DSP2RX_VU, WM8996_DSP2RX_VU);
+ snd_soc_update_bits(codec, WM8996_DSP2_RX_RIGHT_VOLUME,
+ WM8996_DSP2RX_VU, WM8996_DSP2RX_VU);
+
+ /* No support currently for the underclocked TDM modes and
+ * pick a default TDM layout with each channel pair working with
+ * slots 0 and 1. */
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_0_CONFIGURATION,
+ WM8996_AIF1RX_CHAN0_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN0_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_1_CONFIGURATION,
+ WM8996_AIF1RX_CHAN1_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN1_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN1_SLOTS_SHIFT | 1);
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_2_CONFIGURATION,
+ WM8996_AIF1RX_CHAN2_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN2_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN2_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_3_CONFIGURATION,
+ WM8996_AIF1RX_CHAN3_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN3_SLOTS_SHIFT | 1);
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_4_CONFIGURATION,
+ WM8996_AIF1RX_CHAN4_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN4_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1RX_CHANNEL_5_CONFIGURATION,
+ WM8996_AIF1RX_CHAN5_SLOTS_MASK |
+ WM8996_AIF1RX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1RX_CHAN5_SLOTS_SHIFT | 1);
+
+ snd_soc_update_bits(codec, WM8996_AIF2RX_CHANNEL_0_CONFIGURATION,
+ WM8996_AIF2RX_CHAN0_SLOTS_MASK |
+ WM8996_AIF2RX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF2RX_CHAN0_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF2RX_CHANNEL_1_CONFIGURATION,
+ WM8996_AIF2RX_CHAN1_SLOTS_MASK |
+ WM8996_AIF2RX_CHAN1_START_SLOT_MASK,
+ 1 << WM8996_AIF2RX_CHAN1_SLOTS_SHIFT | 1);
+
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_0_CONFIGURATION,
+ WM8996_AIF1TX_CHAN0_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN0_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_1_CONFIGURATION,
+ WM8996_AIF1TX_CHAN1_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN1_SLOTS_SHIFT | 1);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_2_CONFIGURATION,
+ WM8996_AIF1TX_CHAN2_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN2_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_3_CONFIGURATION,
+ WM8996_AIF1TX_CHAN3_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN3_SLOTS_SHIFT | 1);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_4_CONFIGURATION,
+ WM8996_AIF1TX_CHAN4_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN4_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_5_CONFIGURATION,
+ WM8996_AIF1TX_CHAN5_SLOTS_MASK |
+ WM8996_AIF1TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN5_SLOTS_SHIFT | 1);
+
+ snd_soc_update_bits(codec, WM8996_AIF2TX_CHANNEL_0_CONFIGURATION,
+ WM8996_AIF2TX_CHAN0_SLOTS_MASK |
+ WM8996_AIF2TX_CHAN0_START_SLOT_MASK,
+ 1 << WM8996_AIF2TX_CHAN0_SLOTS_SHIFT | 0);
+ snd_soc_update_bits(codec, WM8996_AIF1TX_CHANNEL_1_CONFIGURATION,
+ WM8996_AIF2TX_CHAN1_SLOTS_MASK |
+ WM8996_AIF2TX_CHAN1_START_SLOT_MASK,
+ 1 << WM8996_AIF1TX_CHAN1_SLOTS_SHIFT | 1);
+
+ if (wm8996->pdata.num_retune_mobile_cfgs)
+ wm8996_retune_mobile_pdata(codec);
+ else
+ snd_soc_add_controls(codec, wm8996_eq_controls,
+ ARRAY_SIZE(wm8996_eq_controls));
+
+ /* If the TX LRCLK pins are not in LRCLK mode configure the
+ * AIFs to source their clocks from the RX LRCLKs.
+ */
+ if ((snd_soc_read(codec, WM8996_GPIO_1)))
+ snd_soc_update_bits(codec, WM8996_AIF1_TX_LRCLK_2,
+ WM8996_AIF1TX_LRCLK_MODE,
+ WM8996_AIF1TX_LRCLK_MODE);
+
+ if ((snd_soc_read(codec, WM8996_GPIO_2)))
+ snd_soc_update_bits(codec, WM8996_AIF2_TX_LRCLK_2,
+ WM8996_AIF2TX_LRCLK_MODE,
+ WM8996_AIF2TX_LRCLK_MODE);
+
+ regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
+
+ wm8996_init_gpio(codec);
+
+ if (i2c->irq) {
+ if (wm8996->pdata.irq_flags)
+ irq_flags = wm8996->pdata.irq_flags;
+ else
+ irq_flags = IRQF_TRIGGER_LOW;
+
+ irq_flags |= IRQF_ONESHOT;
+
+ if (irq_flags & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING))
+ ret = request_threaded_irq(i2c->irq, NULL,
+ wm8996_edge_irq,
+ irq_flags, "wm8996", codec);
+ else
+ ret = request_threaded_irq(i2c->irq, NULL, wm8996_irq,
+ irq_flags, "wm8996", codec);
+
+ if (ret == 0) {
+ /* Unmask the interrupt */
+ snd_soc_update_bits(codec, WM8996_INTERRUPT_CONTROL,
+ WM8996_IM_IRQ, 0);
+
+ /* Enable error reporting and DC servo status */
+ snd_soc_update_bits(codec,
+ WM8996_INTERRUPT_STATUS_2_MASK,
+ WM8996_IM_DCS_DONE_23_EINT |
+ WM8996_IM_DCS_DONE_01_EINT |
+ WM8996_IM_FLL_LOCK_EINT |
+ WM8996_IM_FIFOS_ERR_EINT,
+ 0);
+ } else {
+ dev_err(codec->dev, "Failed to request IRQ: %d\n",
+ ret);
+ }
+ }
+
+ return 0;
+
+err_enable:
+ if (wm8996->pdata.ldo_ena >= 0)
+ gpio_set_value_cansleep(wm8996->pdata.ldo_ena, 0);
+
+ regulator_bulk_disable(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
+err_get:
+ regulator_bulk_free(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
+err:
+ return ret;
+}
+
+static int wm8996_remove(struct snd_soc_codec *codec)
+{
+ struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
+ struct i2c_client *i2c = to_i2c_client(codec->dev);
+ int i;
+
+ snd_soc_update_bits(codec, WM8996_INTERRUPT_CONTROL,
+ WM8996_IM_IRQ, WM8996_IM_IRQ);
+
+ if (i2c->irq)
+ free_irq(i2c->irq, codec);
+
+ wm8996_free_gpio(codec);
+
+ for (i = 0; i < ARRAY_SIZE(wm8996->supplies); i++)
+ regulator_unregister_notifier(wm8996->supplies[i].consumer,
+ &wm8996->disable_nb[i]);
+ regulator_bulk_free(ARRAY_SIZE(wm8996->supplies), wm8996->supplies);
+
+ return 0;
+}
+
+static struct snd_soc_codec_driver soc_codec_dev_wm8996 = {
+ .probe = wm8996_probe,
+ .remove = wm8996_remove,
+ .set_bias_level = wm8996_set_bias_level,
+ .seq_notifier = wm8996_seq_notifier,
+ .reg_cache_size = WM8996_MAX_REGISTER + 1,
+ .reg_word_size = sizeof(u16),
+ .reg_cache_default = wm8996_reg,
+ .volatile_register = wm8996_volatile_register,
+ .readable_register = wm8996_readable_register,
+ .compress_type = SND_SOC_RBTREE_COMPRESSION,
+ .controls = wm8996_snd_controls,
+ .num_controls = ARRAY_SIZE(wm8996_snd_controls),
+ .dapm_widgets = wm8996_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(wm8996_dapm_widgets),
+ .dapm_routes = wm8996_dapm_routes,
+ .num_dapm_routes = ARRAY_SIZE(wm8996_dapm_routes),
+ .set_pll = wm8996_set_fll,
+};
+
+#define WM8996_RATES (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\
+ SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_48000)
+#define WM8996_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE |\
+ SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S24_LE |\
+ SNDRV_PCM_FMTBIT_S32_LE)
+
+static struct snd_soc_dai_ops wm8996_dai_ops = {
+ .set_fmt = wm8996_set_fmt,
+ .hw_params = wm8996_hw_params,
+ .set_sysclk = wm8996_set_sysclk,
+};
+
+static struct snd_soc_dai_driver wm8996_dai[] = {
+ {
+ .name = "wm8996-aif1",
+ .playback = {
+ .stream_name = "AIF1 Playback",
+ .channels_min = 1,
+ .channels_max = 6,
+ .rates = WM8996_RATES,
+ .formats = WM8996_FORMATS,
+ },
+ .capture = {
+ .stream_name = "AIF1 Capture",
+ .channels_min = 1,
+ .channels_max = 6,
+ .rates = WM8996_RATES,
+ .formats = WM8996_FORMATS,
+ },
+ .ops = &wm8996_dai_ops,
+ },
+ {
+ .name = "wm8996-aif2",
+ .playback = {
+ .stream_name = "AIF2 Playback",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = WM8996_RATES,
+ .formats = WM8996_FORMATS,
+ },
+ .capture = {
+ .stream_name = "AIF2 Capture",
+ .channels_min = 1,
+ .channels_max = 2,
+ .rates = WM8996_RATES,
+ .formats = WM8996_FORMATS,
+ },
+ .ops = &wm8996_dai_ops,
+ },
+};
+
+static __devinit int wm8996_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct wm8996_priv *wm8996;
+ int ret;
+
+ wm8996 = kzalloc(sizeof(struct wm8996_priv), GFP_KERNEL);
+ if (wm8996 == NULL)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, wm8996);
+
+ if (dev_get_platdata(&i2c->dev))
+ memcpy(&wm8996->pdata, dev_get_platdata(&i2c->dev),
+ sizeof(wm8996->pdata));
+
+ if (wm8996->pdata.ldo_ena > 0) {
+ ret = gpio_request_one(wm8996->pdata.ldo_ena,
+ GPIOF_OUT_INIT_LOW, "WM8996 ENA");
+ if (ret < 0) {
+ dev_err(&i2c->dev, "Failed to request GPIO %d: %d\n",
+ wm8996->pdata.ldo_ena, ret);
+ goto err;
+ }
+ }
+
+ ret = snd_soc_register_codec(&i2c->dev,
+ &soc_codec_dev_wm8996, wm8996_dai,
+ ARRAY_SIZE(wm8996_dai));
+ if (ret < 0)
+ goto err_gpio;
+
+ return ret;
+
+err_gpio:
+ if (wm8996->pdata.ldo_ena > 0)
+ gpio_free(wm8996->pdata.ldo_ena);
+err:
+ kfree(wm8996);
+
+ return ret;
+}
+
+static __devexit int wm8996_i2c_remove(struct i2c_client *client)
+{
+ struct wm8996_priv *wm8996 = i2c_get_clientdata(client);
+
+ snd_soc_unregister_codec(&client->dev);
+ if (wm8996->pdata.ldo_ena > 0)
+ gpio_free(wm8996->pdata.ldo_ena);
+ kfree(i2c_get_clientdata(client));
+ return 0;
+}
+
+static const struct i2c_device_id wm8996_i2c_id[] = {
+ { "wm8996", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, wm8996_i2c_id);
+
+static struct i2c_driver wm8996_i2c_driver = {
+ .driver = {
+ .name = "wm8996",
+ .owner = THIS_MODULE,
+ },
+ .probe = wm8996_i2c_probe,
+ .remove = __devexit_p(wm8996_i2c_remove),
+ .id_table = wm8996_i2c_id,
+};
+
+static int __init wm8996_modinit(void)
+{
+ int ret;
+
+ ret = i2c_add_driver(&wm8996_i2c_driver);
+ if (ret != 0) {
+ printk(KERN_ERR "Failed to register WM8996 I2C driver: %d\n",
+ ret);
+ }
+
+ return ret;
+}
+module_init(wm8996_modinit);
+
+static void __exit wm8996_exit(void)
+{
+ i2c_del_driver(&wm8996_i2c_driver);
+}
+module_exit(wm8996_exit);
+
+MODULE_DESCRIPTION("ASoC WM8996 driver");
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * wm8996.h - WM8996 audio codec interface
+ *
+ * Copyright 2011 Wolfson Microelectronics PLC.
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef _WM8996_H
+#define _WM8996_H
+
+#define WM8996_SYSCLK_MCLK1 1
+#define WM8996_SYSCLK_MCLK2 2
+#define WM8996_SYSCLK_FLL 3
+
+#define WM8996_FLL_MCLK1 1
+#define WM8996_FLL_MCLK2 2
+#define WM8996_FLL_DACLRCLK1 3
+#define WM8996_FLL_BCLK1 4
+
+typedef void (*wm8996_polarity_fn)(struct snd_soc_codec *codec, int polarity);
+
+int wm8996_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack,
+ wm8996_polarity_fn polarity_cb);
+
+/*
+ * Register values.
+ */
+#define WM8996_SOFTWARE_RESET 0x00
+#define WM8996_POWER_MANAGEMENT_1 0x01
+#define WM8996_POWER_MANAGEMENT_2 0x02
+#define WM8996_POWER_MANAGEMENT_3 0x03
+#define WM8996_POWER_MANAGEMENT_4 0x04
+#define WM8996_POWER_MANAGEMENT_5 0x05
+#define WM8996_POWER_MANAGEMENT_6 0x06
+#define WM8996_POWER_MANAGEMENT_7 0x07
+#define WM8996_POWER_MANAGEMENT_8 0x08
+#define WM8996_LEFT_LINE_INPUT_VOLUME 0x10
+#define WM8996_RIGHT_LINE_INPUT_VOLUME 0x11
+#define WM8996_LINE_INPUT_CONTROL 0x12
+#define WM8996_DAC1_HPOUT1_VOLUME 0x15
+#define WM8996_DAC2_HPOUT2_VOLUME 0x16
+#define WM8996_DAC1_LEFT_VOLUME 0x18
+#define WM8996_DAC1_RIGHT_VOLUME 0x19
+#define WM8996_DAC2_LEFT_VOLUME 0x1A
+#define WM8996_DAC2_RIGHT_VOLUME 0x1B
+#define WM8996_OUTPUT1_LEFT_VOLUME 0x1C
+#define WM8996_OUTPUT1_RIGHT_VOLUME 0x1D
+#define WM8996_OUTPUT2_LEFT_VOLUME 0x1E
+#define WM8996_OUTPUT2_RIGHT_VOLUME 0x1F
+#define WM8996_MICBIAS_1 0x20
+#define WM8996_MICBIAS_2 0x21
+#define WM8996_LDO_1 0x28
+#define WM8996_LDO_2 0x29
+#define WM8996_ACCESSORY_DETECT_MODE_1 0x30
+#define WM8996_ACCESSORY_DETECT_MODE_2 0x31
+#define WM8996_HEADPHONE_DETECT_1 0x34
+#define WM8996_HEADPHONE_DETECT_2 0x35
+#define WM8996_MIC_DETECT_1 0x38
+#define WM8996_MIC_DETECT_2 0x39
+#define WM8996_MIC_DETECT_3 0x3A
+#define WM8996_CHARGE_PUMP_1 0x40
+#define WM8996_CHARGE_PUMP_2 0x41
+#define WM8996_DC_SERVO_1 0x50
+#define WM8996_DC_SERVO_2 0x51
+#define WM8996_DC_SERVO_3 0x52
+#define WM8996_DC_SERVO_5 0x54
+#define WM8996_DC_SERVO_6 0x55
+#define WM8996_DC_SERVO_7 0x56
+#define WM8996_DC_SERVO_READBACK_0 0x57
+#define WM8996_ANALOGUE_HP_1 0x60
+#define WM8996_ANALOGUE_HP_2 0x61
+#define WM8996_CHIP_REVISION 0x100
+#define WM8996_CONTROL_INTERFACE_1 0x101
+#define WM8996_WRITE_SEQUENCER_CTRL_1 0x110
+#define WM8996_WRITE_SEQUENCER_CTRL_2 0x111
+#define WM8996_AIF_CLOCKING_1 0x200
+#define WM8996_AIF_CLOCKING_2 0x201
+#define WM8996_CLOCKING_1 0x208
+#define WM8996_CLOCKING_2 0x209
+#define WM8996_AIF_RATE 0x210
+#define WM8996_FLL_CONTROL_1 0x220
+#define WM8996_FLL_CONTROL_2 0x221
+#define WM8996_FLL_CONTROL_3 0x222
+#define WM8996_FLL_CONTROL_4 0x223
+#define WM8996_FLL_CONTROL_5 0x224
+#define WM8996_FLL_CONTROL_6 0x225
+#define WM8996_FLL_EFS_1 0x226
+#define WM8996_FLL_EFS_2 0x227
+#define WM8996_AIF1_CONTROL 0x300
+#define WM8996_AIF1_BCLK 0x301
+#define WM8996_AIF1_TX_LRCLK_1 0x302
+#define WM8996_AIF1_TX_LRCLK_2 0x303
+#define WM8996_AIF1_RX_LRCLK_1 0x304
+#define WM8996_AIF1_RX_LRCLK_2 0x305
+#define WM8996_AIF1TX_DATA_CONFIGURATION_1 0x306
+#define WM8996_AIF1TX_DATA_CONFIGURATION_2 0x307
+#define WM8996_AIF1RX_DATA_CONFIGURATION 0x308
+#define WM8996_AIF1TX_CHANNEL_0_CONFIGURATION 0x309
+#define WM8996_AIF1TX_CHANNEL_1_CONFIGURATION 0x30A
+#define WM8996_AIF1TX_CHANNEL_2_CONFIGURATION 0x30B
+#define WM8996_AIF1TX_CHANNEL_3_CONFIGURATION 0x30C
+#define WM8996_AIF1TX_CHANNEL_4_CONFIGURATION 0x30D
+#define WM8996_AIF1TX_CHANNEL_5_CONFIGURATION 0x30E
+#define WM8996_AIF1RX_CHANNEL_0_CONFIGURATION 0x30F
+#define WM8996_AIF1RX_CHANNEL_1_CONFIGURATION 0x310
+#define WM8996_AIF1RX_CHANNEL_2_CONFIGURATION 0x311
+#define WM8996_AIF1RX_CHANNEL_3_CONFIGURATION 0x312
+#define WM8996_AIF1RX_CHANNEL_4_CONFIGURATION 0x313
+#define WM8996_AIF1RX_CHANNEL_5_CONFIGURATION 0x314
+#define WM8996_AIF1RX_MONO_CONFIGURATION 0x315
+#define WM8996_AIF1TX_TEST 0x31A
+#define WM8996_AIF2_CONTROL 0x320
+#define WM8996_AIF2_BCLK 0x321
+#define WM8996_AIF2_TX_LRCLK_1 0x322
+#define WM8996_AIF2_TX_LRCLK_2 0x323
+#define WM8996_AIF2_RX_LRCLK_1 0x324
+#define WM8996_AIF2_RX_LRCLK_2 0x325
+#define WM8996_AIF2TX_DATA_CONFIGURATION_1 0x326
+#define WM8996_AIF2TX_DATA_CONFIGURATION_2 0x327
+#define WM8996_AIF2RX_DATA_CONFIGURATION 0x328
+#define WM8996_AIF2TX_CHANNEL_0_CONFIGURATION 0x329
+#define WM8996_AIF2TX_CHANNEL_1_CONFIGURATION 0x32A
+#define WM8996_AIF2RX_CHANNEL_0_CONFIGURATION 0x32B
+#define WM8996_AIF2RX_CHANNEL_1_CONFIGURATION 0x32C
+#define WM8996_AIF2RX_MONO_CONFIGURATION 0x32D
+#define WM8996_AIF2TX_TEST 0x32F
+#define WM8996_DSP1_TX_LEFT_VOLUME 0x400
+#define WM8996_DSP1_TX_RIGHT_VOLUME 0x401
+#define WM8996_DSP1_RX_LEFT_VOLUME 0x402
+#define WM8996_DSP1_RX_RIGHT_VOLUME 0x403
+#define WM8996_DSP1_TX_FILTERS 0x410
+#define WM8996_DSP1_RX_FILTERS_1 0x420
+#define WM8996_DSP1_RX_FILTERS_2 0x421
+#define WM8996_DSP1_DRC_1 0x440
+#define WM8996_DSP1_DRC_2 0x441
+#define WM8996_DSP1_DRC_3 0x442
+#define WM8996_DSP1_DRC_4 0x443
+#define WM8996_DSP1_DRC_5 0x444
+#define WM8996_DSP1_RX_EQ_GAINS_1 0x480
+#define WM8996_DSP1_RX_EQ_GAINS_2 0x481
+#define WM8996_DSP1_RX_EQ_BAND_1_A 0x482
+#define WM8996_DSP1_RX_EQ_BAND_1_B 0x483
+#define WM8996_DSP1_RX_EQ_BAND_1_PG 0x484
+#define WM8996_DSP1_RX_EQ_BAND_2_A 0x485
+#define WM8996_DSP1_RX_EQ_BAND_2_B 0x486
+#define WM8996_DSP1_RX_EQ_BAND_2_C 0x487
+#define WM8996_DSP1_RX_EQ_BAND_2_PG 0x488
+#define WM8996_DSP1_RX_EQ_BAND_3_A 0x489
+#define WM8996_DSP1_RX_EQ_BAND_3_B 0x48A
+#define WM8996_DSP1_RX_EQ_BAND_3_C 0x48B
+#define WM8996_DSP1_RX_EQ_BAND_3_PG 0x48C
+#define WM8996_DSP1_RX_EQ_BAND_4_A 0x48D
+#define WM8996_DSP1_RX_EQ_BAND_4_B 0x48E
+#define WM8996_DSP1_RX_EQ_BAND_4_C 0x48F
+#define WM8996_DSP1_RX_EQ_BAND_4_PG 0x490
+#define WM8996_DSP1_RX_EQ_BAND_5_A 0x491
+#define WM8996_DSP1_RX_EQ_BAND_5_B 0x492
+#define WM8996_DSP1_RX_EQ_BAND_5_PG 0x493
+#define WM8996_DSP2_TX_LEFT_VOLUME 0x500
+#define WM8996_DSP2_TX_RIGHT_VOLUME 0x501
+#define WM8996_DSP2_RX_LEFT_VOLUME 0x502
+#define WM8996_DSP2_RX_RIGHT_VOLUME 0x503
+#define WM8996_DSP2_TX_FILTERS 0x510
+#define WM8996_DSP2_RX_FILTERS_1 0x520
+#define WM8996_DSP2_RX_FILTERS_2 0x521
+#define WM8996_DSP2_DRC_1 0x540
+#define WM8996_DSP2_DRC_2 0x541
+#define WM8996_DSP2_DRC_3 0x542
+#define WM8996_DSP2_DRC_4 0x543
+#define WM8996_DSP2_DRC_5 0x544
+#define WM8996_DSP2_RX_EQ_GAINS_1 0x580
+#define WM8996_DSP2_RX_EQ_GAINS_2 0x581
+#define WM8996_DSP2_RX_EQ_BAND_1_A 0x582
+#define WM8996_DSP2_RX_EQ_BAND_1_B 0x583
+#define WM8996_DSP2_RX_EQ_BAND_1_PG 0x584
+#define WM8996_DSP2_RX_EQ_BAND_2_A 0x585
+#define WM8996_DSP2_RX_EQ_BAND_2_B 0x586
+#define WM8996_DSP2_RX_EQ_BAND_2_C 0x587
+#define WM8996_DSP2_RX_EQ_BAND_2_PG 0x588
+#define WM8996_DSP2_RX_EQ_BAND_3_A 0x589
+#define WM8996_DSP2_RX_EQ_BAND_3_B 0x58A
+#define WM8996_DSP2_RX_EQ_BAND_3_C 0x58B
+#define WM8996_DSP2_RX_EQ_BAND_3_PG 0x58C
+#define WM8996_DSP2_RX_EQ_BAND_4_A 0x58D
+#define WM8996_DSP2_RX_EQ_BAND_4_B 0x58E
+#define WM8996_DSP2_RX_EQ_BAND_4_C 0x58F
+#define WM8996_DSP2_RX_EQ_BAND_4_PG 0x590
+#define WM8996_DSP2_RX_EQ_BAND_5_A 0x591
+#define WM8996_DSP2_RX_EQ_BAND_5_B 0x592
+#define WM8996_DSP2_RX_EQ_BAND_5_PG 0x593
+#define WM8996_DAC1_MIXER_VOLUMES 0x600
+#define WM8996_DAC1_LEFT_MIXER_ROUTING 0x601
+#define WM8996_DAC1_RIGHT_MIXER_ROUTING 0x602
+#define WM8996_DAC2_MIXER_VOLUMES 0x603
+#define WM8996_DAC2_LEFT_MIXER_ROUTING 0x604
+#define WM8996_DAC2_RIGHT_MIXER_ROUTING 0x605
+#define WM8996_DSP1_TX_LEFT_MIXER_ROUTING 0x606
+#define WM8996_DSP1_TX_RIGHT_MIXER_ROUTING 0x607
+#define WM8996_DSP2_TX_LEFT_MIXER_ROUTING 0x608
+#define WM8996_DSP2_TX_RIGHT_MIXER_ROUTING 0x609
+#define WM8996_DSP_TX_MIXER_SELECT 0x60A
+#define WM8996_DAC_SOFTMUTE 0x610
+#define WM8996_OVERSAMPLING 0x620
+#define WM8996_SIDETONE 0x621
+#define WM8996_GPIO_1 0x700
+#define WM8996_GPIO_2 0x701
+#define WM8996_GPIO_3 0x702
+#define WM8996_GPIO_4 0x703
+#define WM8996_GPIO_5 0x704
+#define WM8996_PULL_CONTROL_1 0x720
+#define WM8996_PULL_CONTROL_2 0x721
+#define WM8996_INTERRUPT_STATUS_1 0x730
+#define WM8996_INTERRUPT_STATUS_2 0x731
+#define WM8996_INTERRUPT_RAW_STATUS_2 0x732
+#define WM8996_INTERRUPT_STATUS_1_MASK 0x738
+#define WM8996_INTERRUPT_STATUS_2_MASK 0x739
+#define WM8996_INTERRUPT_CONTROL 0x740
+#define WM8996_LEFT_PDM_SPEAKER 0x800
+#define WM8996_RIGHT_PDM_SPEAKER 0x801
+#define WM8996_PDM_SPEAKER_MUTE_SEQUENCE 0x802
+#define WM8996_PDM_SPEAKER_VOLUME 0x803
+#define WM8996_WRITE_SEQUENCER_0 0x3000
+#define WM8996_WRITE_SEQUENCER_1 0x3001
+#define WM8996_WRITE_SEQUENCER_2 0x3002
+#define WM8996_WRITE_SEQUENCER_3 0x3003
+#define WM8996_WRITE_SEQUENCER_4 0x3004
+#define WM8996_WRITE_SEQUENCER_5 0x3005
+#define WM8996_WRITE_SEQUENCER_6 0x3006
+#define WM8996_WRITE_SEQUENCER_7 0x3007
+#define WM8996_WRITE_SEQUENCER_8 0x3008
+#define WM8996_WRITE_SEQUENCER_9 0x3009
+#define WM8996_WRITE_SEQUENCER_10 0x300A
+#define WM8996_WRITE_SEQUENCER_11 0x300B
+#define WM8996_WRITE_SEQUENCER_12 0x300C
+#define WM8996_WRITE_SEQUENCER_13 0x300D
+#define WM8996_WRITE_SEQUENCER_14 0x300E
+#define WM8996_WRITE_SEQUENCER_15 0x300F
+#define WM8996_WRITE_SEQUENCER_16 0x3010
+#define WM8996_WRITE_SEQUENCER_17 0x3011
+#define WM8996_WRITE_SEQUENCER_18 0x3012
+#define WM8996_WRITE_SEQUENCER_19 0x3013
+#define WM8996_WRITE_SEQUENCER_20 0x3014
+#define WM8996_WRITE_SEQUENCER_21 0x3015
+#define WM8996_WRITE_SEQUENCER_22 0x3016
+#define WM8996_WRITE_SEQUENCER_23 0x3017
+#define WM8996_WRITE_SEQUENCER_24 0x3018
+#define WM8996_WRITE_SEQUENCER_25 0x3019
+#define WM8996_WRITE_SEQUENCER_26 0x301A
+#define WM8996_WRITE_SEQUENCER_27 0x301B
+#define WM8996_WRITE_SEQUENCER_28 0x301C
+#define WM8996_WRITE_SEQUENCER_29 0x301D
+#define WM8996_WRITE_SEQUENCER_30 0x301E
+#define WM8996_WRITE_SEQUENCER_31 0x301F
+#define WM8996_WRITE_SEQUENCER_32 0x3020
+#define WM8996_WRITE_SEQUENCER_33 0x3021
+#define WM8996_WRITE_SEQUENCER_34 0x3022
+#define WM8996_WRITE_SEQUENCER_35 0x3023
+#define WM8996_WRITE_SEQUENCER_36 0x3024
+#define WM8996_WRITE_SEQUENCER_37 0x3025
+#define WM8996_WRITE_SEQUENCER_38 0x3026
+#define WM8996_WRITE_SEQUENCER_39 0x3027
+#define WM8996_WRITE_SEQUENCER_40 0x3028
+#define WM8996_WRITE_SEQUENCER_41 0x3029
+#define WM8996_WRITE_SEQUENCER_42 0x302A
+#define WM8996_WRITE_SEQUENCER_43 0x302B
+#define WM8996_WRITE_SEQUENCER_44 0x302C
+#define WM8996_WRITE_SEQUENCER_45 0x302D
+#define WM8996_WRITE_SEQUENCER_46 0x302E
+#define WM8996_WRITE_SEQUENCER_47 0x302F
+#define WM8996_WRITE_SEQUENCER_48 0x3030
+#define WM8996_WRITE_SEQUENCER_49 0x3031
+#define WM8996_WRITE_SEQUENCER_50 0x3032
+#define WM8996_WRITE_SEQUENCER_51 0x3033
+#define WM8996_WRITE_SEQUENCER_52 0x3034
+#define WM8996_WRITE_SEQUENCER_53 0x3035
+#define WM8996_WRITE_SEQUENCER_54 0x3036
+#define WM8996_WRITE_SEQUENCER_55 0x3037
+#define WM8996_WRITE_SEQUENCER_56 0x3038
+#define WM8996_WRITE_SEQUENCER_57 0x3039
+#define WM8996_WRITE_SEQUENCER_58 0x303A
+#define WM8996_WRITE_SEQUENCER_59 0x303B
+#define WM8996_WRITE_SEQUENCER_60 0x303C
+#define WM8996_WRITE_SEQUENCER_61 0x303D
+#define WM8996_WRITE_SEQUENCER_62 0x303E
+#define WM8996_WRITE_SEQUENCER_63 0x303F
+#define WM8996_WRITE_SEQUENCER_64 0x3040
+#define WM8996_WRITE_SEQUENCER_65 0x3041
+#define WM8996_WRITE_SEQUENCER_66 0x3042
+#define WM8996_WRITE_SEQUENCER_67 0x3043
+#define WM8996_WRITE_SEQUENCER_68 0x3044
+#define WM8996_WRITE_SEQUENCER_69 0x3045
+#define WM8996_WRITE_SEQUENCER_70 0x3046
+#define WM8996_WRITE_SEQUENCER_71 0x3047
+#define WM8996_WRITE_SEQUENCER_72 0x3048
+#define WM8996_WRITE_SEQUENCER_73 0x3049
+#define WM8996_WRITE_SEQUENCER_74 0x304A
+#define WM8996_WRITE_SEQUENCER_75 0x304B
+#define WM8996_WRITE_SEQUENCER_76 0x304C
+#define WM8996_WRITE_SEQUENCER_77 0x304D
+#define WM8996_WRITE_SEQUENCER_78 0x304E
+#define WM8996_WRITE_SEQUENCER_79 0x304F
+#define WM8996_WRITE_SEQUENCER_80 0x3050
+#define WM8996_WRITE_SEQUENCER_81 0x3051
+#define WM8996_WRITE_SEQUENCER_82 0x3052
+#define WM8996_WRITE_SEQUENCER_83 0x3053
+#define WM8996_WRITE_SEQUENCER_84 0x3054
+#define WM8996_WRITE_SEQUENCER_85 0x3055
+#define WM8996_WRITE_SEQUENCER_86 0x3056
+#define WM8996_WRITE_SEQUENCER_87 0x3057
+#define WM8996_WRITE_SEQUENCER_88 0x3058
+#define WM8996_WRITE_SEQUENCER_89 0x3059
+#define WM8996_WRITE_SEQUENCER_90 0x305A
+#define WM8996_WRITE_SEQUENCER_91 0x305B
+#define WM8996_WRITE_SEQUENCER_92 0x305C
+#define WM8996_WRITE_SEQUENCER_93 0x305D
+#define WM8996_WRITE_SEQUENCER_94 0x305E
+#define WM8996_WRITE_SEQUENCER_95 0x305F
+#define WM8996_WRITE_SEQUENCER_96 0x3060
+#define WM8996_WRITE_SEQUENCER_97 0x3061
+#define WM8996_WRITE_SEQUENCER_98 0x3062
+#define WM8996_WRITE_SEQUENCER_99 0x3063
+#define WM8996_WRITE_SEQUENCER_100 0x3064
+#define WM8996_WRITE_SEQUENCER_101 0x3065
+#define WM8996_WRITE_SEQUENCER_102 0x3066
+#define WM8996_WRITE_SEQUENCER_103 0x3067
+#define WM8996_WRITE_SEQUENCER_104 0x3068
+#define WM8996_WRITE_SEQUENCER_105 0x3069
+#define WM8996_WRITE_SEQUENCER_106 0x306A
+#define WM8996_WRITE_SEQUENCER_107 0x306B
+#define WM8996_WRITE_SEQUENCER_108 0x306C
+#define WM8996_WRITE_SEQUENCER_109 0x306D
+#define WM8996_WRITE_SEQUENCER_110 0x306E
+#define WM8996_WRITE_SEQUENCER_111 0x306F
+#define WM8996_WRITE_SEQUENCER_112 0x3070
+#define WM8996_WRITE_SEQUENCER_113 0x3071
+#define WM8996_WRITE_SEQUENCER_114 0x3072
+#define WM8996_WRITE_SEQUENCER_115 0x3073
+#define WM8996_WRITE_SEQUENCER_116 0x3074
+#define WM8996_WRITE_SEQUENCER_117 0x3075
+#define WM8996_WRITE_SEQUENCER_118 0x3076
+#define WM8996_WRITE_SEQUENCER_119 0x3077
+#define WM8996_WRITE_SEQUENCER_120 0x3078
+#define WM8996_WRITE_SEQUENCER_121 0x3079
+#define WM8996_WRITE_SEQUENCER_122 0x307A
+#define WM8996_WRITE_SEQUENCER_123 0x307B
+#define WM8996_WRITE_SEQUENCER_124 0x307C
+#define WM8996_WRITE_SEQUENCER_125 0x307D
+#define WM8996_WRITE_SEQUENCER_126 0x307E
+#define WM8996_WRITE_SEQUENCER_127 0x307F
+#define WM8996_WRITE_SEQUENCER_128 0x3080
+#define WM8996_WRITE_SEQUENCER_129 0x3081
+#define WM8996_WRITE_SEQUENCER_130 0x3082
+#define WM8996_WRITE_SEQUENCER_131 0x3083
+#define WM8996_WRITE_SEQUENCER_132 0x3084
+#define WM8996_WRITE_SEQUENCER_133 0x3085
+#define WM8996_WRITE_SEQUENCER_134 0x3086
+#define WM8996_WRITE_SEQUENCER_135 0x3087
+#define WM8996_WRITE_SEQUENCER_136 0x3088
+#define WM8996_WRITE_SEQUENCER_137 0x3089
+#define WM8996_WRITE_SEQUENCER_138 0x308A
+#define WM8996_WRITE_SEQUENCER_139 0x308B
+#define WM8996_WRITE_SEQUENCER_140 0x308C
+#define WM8996_WRITE_SEQUENCER_141 0x308D
+#define WM8996_WRITE_SEQUENCER_142 0x308E
+#define WM8996_WRITE_SEQUENCER_143 0x308F
+#define WM8996_WRITE_SEQUENCER_144 0x3090
+#define WM8996_WRITE_SEQUENCER_145 0x3091
+#define WM8996_WRITE_SEQUENCER_146 0x3092
+#define WM8996_WRITE_SEQUENCER_147 0x3093
+#define WM8996_WRITE_SEQUENCER_148 0x3094
+#define WM8996_WRITE_SEQUENCER_149 0x3095
+#define WM8996_WRITE_SEQUENCER_150 0x3096
+#define WM8996_WRITE_SEQUENCER_151 0x3097
+#define WM8996_WRITE_SEQUENCER_152 0x3098
+#define WM8996_WRITE_SEQUENCER_153 0x3099
+#define WM8996_WRITE_SEQUENCER_154 0x309A
+#define WM8996_WRITE_SEQUENCER_155 0x309B
+#define WM8996_WRITE_SEQUENCER_156 0x309C
+#define WM8996_WRITE_SEQUENCER_157 0x309D
+#define WM8996_WRITE_SEQUENCER_158 0x309E
+#define WM8996_WRITE_SEQUENCER_159 0x309F
+#define WM8996_WRITE_SEQUENCER_160 0x30A0
+#define WM8996_WRITE_SEQUENCER_161 0x30A1
+#define WM8996_WRITE_SEQUENCER_162 0x30A2
+#define WM8996_WRITE_SEQUENCER_163 0x30A3
+#define WM8996_WRITE_SEQUENCER_164 0x30A4
+#define WM8996_WRITE_SEQUENCER_165 0x30A5
+#define WM8996_WRITE_SEQUENCER_166 0x30A6
+#define WM8996_WRITE_SEQUENCER_167 0x30A7
+#define WM8996_WRITE_SEQUENCER_168 0x30A8
+#define WM8996_WRITE_SEQUENCER_169 0x30A9
+#define WM8996_WRITE_SEQUENCER_170 0x30AA
+#define WM8996_WRITE_SEQUENCER_171 0x30AB
+#define WM8996_WRITE_SEQUENCER_172 0x30AC
+#define WM8996_WRITE_SEQUENCER_173 0x30AD
+#define WM8996_WRITE_SEQUENCER_174 0x30AE
+#define WM8996_WRITE_SEQUENCER_175 0x30AF
+#define WM8996_WRITE_SEQUENCER_176 0x30B0
+#define WM8996_WRITE_SEQUENCER_177 0x30B1
+#define WM8996_WRITE_SEQUENCER_178 0x30B2
+#define WM8996_WRITE_SEQUENCER_179 0x30B3
+#define WM8996_WRITE_SEQUENCER_180 0x30B4
+#define WM8996_WRITE_SEQUENCER_181 0x30B5
+#define WM8996_WRITE_SEQUENCER_182 0x30B6
+#define WM8996_WRITE_SEQUENCER_183 0x30B7
+#define WM8996_WRITE_SEQUENCER_184 0x30B8
+#define WM8996_WRITE_SEQUENCER_185 0x30B9
+#define WM8996_WRITE_SEQUENCER_186 0x30BA
+#define WM8996_WRITE_SEQUENCER_187 0x30BB
+#define WM8996_WRITE_SEQUENCER_188 0x30BC
+#define WM8996_WRITE_SEQUENCER_189 0x30BD
+#define WM8996_WRITE_SEQUENCER_190 0x30BE
+#define WM8996_WRITE_SEQUENCER_191 0x30BF
+#define WM8996_WRITE_SEQUENCER_192 0x30C0
+#define WM8996_WRITE_SEQUENCER_193 0x30C1
+#define WM8996_WRITE_SEQUENCER_194 0x30C2
+#define WM8996_WRITE_SEQUENCER_195 0x30C3
+#define WM8996_WRITE_SEQUENCER_196 0x30C4
+#define WM8996_WRITE_SEQUENCER_197 0x30C5
+#define WM8996_WRITE_SEQUENCER_198 0x30C6
+#define WM8996_WRITE_SEQUENCER_199 0x30C7
+#define WM8996_WRITE_SEQUENCER_200 0x30C8
+#define WM8996_WRITE_SEQUENCER_201 0x30C9
+#define WM8996_WRITE_SEQUENCER_202 0x30CA
+#define WM8996_WRITE_SEQUENCER_203 0x30CB
+#define WM8996_WRITE_SEQUENCER_204 0x30CC
+#define WM8996_WRITE_SEQUENCER_205 0x30CD
+#define WM8996_WRITE_SEQUENCER_206 0x30CE
+#define WM8996_WRITE_SEQUENCER_207 0x30CF
+#define WM8996_WRITE_SEQUENCER_208 0x30D0
+#define WM8996_WRITE_SEQUENCER_209 0x30D1
+#define WM8996_WRITE_SEQUENCER_210 0x30D2
+#define WM8996_WRITE_SEQUENCER_211 0x30D3
+#define WM8996_WRITE_SEQUENCER_212 0x30D4
+#define WM8996_WRITE_SEQUENCER_213 0x30D5
+#define WM8996_WRITE_SEQUENCER_214 0x30D6
+#define WM8996_WRITE_SEQUENCER_215 0x30D7
+#define WM8996_WRITE_SEQUENCER_216 0x30D8
+#define WM8996_WRITE_SEQUENCER_217 0x30D9
+#define WM8996_WRITE_SEQUENCER_218 0x30DA
+#define WM8996_WRITE_SEQUENCER_219 0x30DB
+#define WM8996_WRITE_SEQUENCER_220 0x30DC
+#define WM8996_WRITE_SEQUENCER_221 0x30DD
+#define WM8996_WRITE_SEQUENCER_222 0x30DE
+#define WM8996_WRITE_SEQUENCER_223 0x30DF
+#define WM8996_WRITE_SEQUENCER_224 0x30E0
+#define WM8996_WRITE_SEQUENCER_225 0x30E1
+#define WM8996_WRITE_SEQUENCER_226 0x30E2
+#define WM8996_WRITE_SEQUENCER_227 0x30E3
+#define WM8996_WRITE_SEQUENCER_228 0x30E4
+#define WM8996_WRITE_SEQUENCER_229 0x30E5
+#define WM8996_WRITE_SEQUENCER_230 0x30E6
+#define WM8996_WRITE_SEQUENCER_231 0x30E7
+#define WM8996_WRITE_SEQUENCER_232 0x30E8
+#define WM8996_WRITE_SEQUENCER_233 0x30E9
+#define WM8996_WRITE_SEQUENCER_234 0x30EA
+#define WM8996_WRITE_SEQUENCER_235 0x30EB
+#define WM8996_WRITE_SEQUENCER_236 0x30EC
+#define WM8996_WRITE_SEQUENCER_237 0x30ED
+#define WM8996_WRITE_SEQUENCER_238 0x30EE
+#define WM8996_WRITE_SEQUENCER_239 0x30EF
+#define WM8996_WRITE_SEQUENCER_240 0x30F0
+#define WM8996_WRITE_SEQUENCER_241 0x30F1
+#define WM8996_WRITE_SEQUENCER_242 0x30F2
+#define WM8996_WRITE_SEQUENCER_243 0x30F3
+#define WM8996_WRITE_SEQUENCER_244 0x30F4
+#define WM8996_WRITE_SEQUENCER_245 0x30F5
+#define WM8996_WRITE_SEQUENCER_246 0x30F6
+#define WM8996_WRITE_SEQUENCER_247 0x30F7
+#define WM8996_WRITE_SEQUENCER_248 0x30F8
+#define WM8996_WRITE_SEQUENCER_249 0x30F9
+#define WM8996_WRITE_SEQUENCER_250 0x30FA
+#define WM8996_WRITE_SEQUENCER_251 0x30FB
+#define WM8996_WRITE_SEQUENCER_252 0x30FC
+#define WM8996_WRITE_SEQUENCER_253 0x30FD
+#define WM8996_WRITE_SEQUENCER_254 0x30FE
+#define WM8996_WRITE_SEQUENCER_255 0x30FF
+#define WM8996_WRITE_SEQUENCER_256 0x3100
+#define WM8996_WRITE_SEQUENCER_257 0x3101
+#define WM8996_WRITE_SEQUENCER_258 0x3102
+#define WM8996_WRITE_SEQUENCER_259 0x3103
+#define WM8996_WRITE_SEQUENCER_260 0x3104
+#define WM8996_WRITE_SEQUENCER_261 0x3105
+#define WM8996_WRITE_SEQUENCER_262 0x3106
+#define WM8996_WRITE_SEQUENCER_263 0x3107
+#define WM8996_WRITE_SEQUENCER_264 0x3108
+#define WM8996_WRITE_SEQUENCER_265 0x3109
+#define WM8996_WRITE_SEQUENCER_266 0x310A
+#define WM8996_WRITE_SEQUENCER_267 0x310B
+#define WM8996_WRITE_SEQUENCER_268 0x310C
+#define WM8996_WRITE_SEQUENCER_269 0x310D
+#define WM8996_WRITE_SEQUENCER_270 0x310E
+#define WM8996_WRITE_SEQUENCER_271 0x310F
+#define WM8996_WRITE_SEQUENCER_272 0x3110
+#define WM8996_WRITE_SEQUENCER_273 0x3111
+#define WM8996_WRITE_SEQUENCER_274 0x3112
+#define WM8996_WRITE_SEQUENCER_275 0x3113
+#define WM8996_WRITE_SEQUENCER_276 0x3114
+#define WM8996_WRITE_SEQUENCER_277 0x3115
+#define WM8996_WRITE_SEQUENCER_278 0x3116
+#define WM8996_WRITE_SEQUENCER_279 0x3117
+#define WM8996_WRITE_SEQUENCER_280 0x3118
+#define WM8996_WRITE_SEQUENCER_281 0x3119
+#define WM8996_WRITE_SEQUENCER_282 0x311A
+#define WM8996_WRITE_SEQUENCER_283 0x311B
+#define WM8996_WRITE_SEQUENCER_284 0x311C
+#define WM8996_WRITE_SEQUENCER_285 0x311D
+#define WM8996_WRITE_SEQUENCER_286 0x311E
+#define WM8996_WRITE_SEQUENCER_287 0x311F
+#define WM8996_WRITE_SEQUENCER_288 0x3120
+#define WM8996_WRITE_SEQUENCER_289 0x3121
+#define WM8996_WRITE_SEQUENCER_290 0x3122
+#define WM8996_WRITE_SEQUENCER_291 0x3123
+#define WM8996_WRITE_SEQUENCER_292 0x3124
+#define WM8996_WRITE_SEQUENCER_293 0x3125
+#define WM8996_WRITE_SEQUENCER_294 0x3126
+#define WM8996_WRITE_SEQUENCER_295 0x3127
+#define WM8996_WRITE_SEQUENCER_296 0x3128
+#define WM8996_WRITE_SEQUENCER_297 0x3129
+#define WM8996_WRITE_SEQUENCER_298 0x312A
+#define WM8996_WRITE_SEQUENCER_299 0x312B
+#define WM8996_WRITE_SEQUENCER_300 0x312C
+#define WM8996_WRITE_SEQUENCER_301 0x312D
+#define WM8996_WRITE_SEQUENCER_302 0x312E
+#define WM8996_WRITE_SEQUENCER_303 0x312F
+#define WM8996_WRITE_SEQUENCER_304 0x3130
+#define WM8996_WRITE_SEQUENCER_305 0x3131
+#define WM8996_WRITE_SEQUENCER_306 0x3132
+#define WM8996_WRITE_SEQUENCER_307 0x3133
+#define WM8996_WRITE_SEQUENCER_308 0x3134
+#define WM8996_WRITE_SEQUENCER_309 0x3135
+#define WM8996_WRITE_SEQUENCER_310 0x3136
+#define WM8996_WRITE_SEQUENCER_311 0x3137
+#define WM8996_WRITE_SEQUENCER_312 0x3138
+#define WM8996_WRITE_SEQUENCER_313 0x3139
+#define WM8996_WRITE_SEQUENCER_314 0x313A
+#define WM8996_WRITE_SEQUENCER_315 0x313B
+#define WM8996_WRITE_SEQUENCER_316 0x313C
+#define WM8996_WRITE_SEQUENCER_317 0x313D
+#define WM8996_WRITE_SEQUENCER_318 0x313E
+#define WM8996_WRITE_SEQUENCER_319 0x313F
+#define WM8996_WRITE_SEQUENCER_320 0x3140
+#define WM8996_WRITE_SEQUENCER_321 0x3141
+#define WM8996_WRITE_SEQUENCER_322 0x3142
+#define WM8996_WRITE_SEQUENCER_323 0x3143
+#define WM8996_WRITE_SEQUENCER_324 0x3144
+#define WM8996_WRITE_SEQUENCER_325 0x3145
+#define WM8996_WRITE_SEQUENCER_326 0x3146
+#define WM8996_WRITE_SEQUENCER_327 0x3147
+#define WM8996_WRITE_SEQUENCER_328 0x3148
+#define WM8996_WRITE_SEQUENCER_329 0x3149
+#define WM8996_WRITE_SEQUENCER_330 0x314A
+#define WM8996_WRITE_SEQUENCER_331 0x314B
+#define WM8996_WRITE_SEQUENCER_332 0x314C
+#define WM8996_WRITE_SEQUENCER_333 0x314D
+#define WM8996_WRITE_SEQUENCER_334 0x314E
+#define WM8996_WRITE_SEQUENCER_335 0x314F
+#define WM8996_WRITE_SEQUENCER_336 0x3150
+#define WM8996_WRITE_SEQUENCER_337 0x3151
+#define WM8996_WRITE_SEQUENCER_338 0x3152
+#define WM8996_WRITE_SEQUENCER_339 0x3153
+#define WM8996_WRITE_SEQUENCER_340 0x3154
+#define WM8996_WRITE_SEQUENCER_341 0x3155
+#define WM8996_WRITE_SEQUENCER_342 0x3156
+#define WM8996_WRITE_SEQUENCER_343 0x3157
+#define WM8996_WRITE_SEQUENCER_344 0x3158
+#define WM8996_WRITE_SEQUENCER_345 0x3159
+#define WM8996_WRITE_SEQUENCER_346 0x315A
+#define WM8996_WRITE_SEQUENCER_347 0x315B
+#define WM8996_WRITE_SEQUENCER_348 0x315C
+#define WM8996_WRITE_SEQUENCER_349 0x315D
+#define WM8996_WRITE_SEQUENCER_350 0x315E
+#define WM8996_WRITE_SEQUENCER_351 0x315F
+#define WM8996_WRITE_SEQUENCER_352 0x3160
+#define WM8996_WRITE_SEQUENCER_353 0x3161
+#define WM8996_WRITE_SEQUENCER_354 0x3162
+#define WM8996_WRITE_SEQUENCER_355 0x3163
+#define WM8996_WRITE_SEQUENCER_356 0x3164
+#define WM8996_WRITE_SEQUENCER_357 0x3165
+#define WM8996_WRITE_SEQUENCER_358 0x3166
+#define WM8996_WRITE_SEQUENCER_359 0x3167
+#define WM8996_WRITE_SEQUENCER_360 0x3168
+#define WM8996_WRITE_SEQUENCER_361 0x3169
+#define WM8996_WRITE_SEQUENCER_362 0x316A
+#define WM8996_WRITE_SEQUENCER_363 0x316B
+#define WM8996_WRITE_SEQUENCER_364 0x316C
+#define WM8996_WRITE_SEQUENCER_365 0x316D
+#define WM8996_WRITE_SEQUENCER_366 0x316E
+#define WM8996_WRITE_SEQUENCER_367 0x316F
+#define WM8996_WRITE_SEQUENCER_368 0x3170
+#define WM8996_WRITE_SEQUENCER_369 0x3171
+#define WM8996_WRITE_SEQUENCER_370 0x3172
+#define WM8996_WRITE_SEQUENCER_371 0x3173
+#define WM8996_WRITE_SEQUENCER_372 0x3174
+#define WM8996_WRITE_SEQUENCER_373 0x3175
+#define WM8996_WRITE_SEQUENCER_374 0x3176
+#define WM8996_WRITE_SEQUENCER_375 0x3177
+#define WM8996_WRITE_SEQUENCER_376 0x3178
+#define WM8996_WRITE_SEQUENCER_377 0x3179
+#define WM8996_WRITE_SEQUENCER_378 0x317A
+#define WM8996_WRITE_SEQUENCER_379 0x317B
+#define WM8996_WRITE_SEQUENCER_380 0x317C
+#define WM8996_WRITE_SEQUENCER_381 0x317D
+#define WM8996_WRITE_SEQUENCER_382 0x317E
+#define WM8996_WRITE_SEQUENCER_383 0x317F
+#define WM8996_WRITE_SEQUENCER_384 0x3180
+#define WM8996_WRITE_SEQUENCER_385 0x3181
+#define WM8996_WRITE_SEQUENCER_386 0x3182
+#define WM8996_WRITE_SEQUENCER_387 0x3183
+#define WM8996_WRITE_SEQUENCER_388 0x3184
+#define WM8996_WRITE_SEQUENCER_389 0x3185
+#define WM8996_WRITE_SEQUENCER_390 0x3186
+#define WM8996_WRITE_SEQUENCER_391 0x3187
+#define WM8996_WRITE_SEQUENCER_392 0x3188
+#define WM8996_WRITE_SEQUENCER_393 0x3189
+#define WM8996_WRITE_SEQUENCER_394 0x318A
+#define WM8996_WRITE_SEQUENCER_395 0x318B
+#define WM8996_WRITE_SEQUENCER_396 0x318C
+#define WM8996_WRITE_SEQUENCER_397 0x318D
+#define WM8996_WRITE_SEQUENCER_398 0x318E
+#define WM8996_WRITE_SEQUENCER_399 0x318F
+#define WM8996_WRITE_SEQUENCER_400 0x3190
+#define WM8996_WRITE_SEQUENCER_401 0x3191
+#define WM8996_WRITE_SEQUENCER_402 0x3192
+#define WM8996_WRITE_SEQUENCER_403 0x3193
+#define WM8996_WRITE_SEQUENCER_404 0x3194
+#define WM8996_WRITE_SEQUENCER_405 0x3195
+#define WM8996_WRITE_SEQUENCER_406 0x3196
+#define WM8996_WRITE_SEQUENCER_407 0x3197
+#define WM8996_WRITE_SEQUENCER_408 0x3198
+#define WM8996_WRITE_SEQUENCER_409 0x3199
+#define WM8996_WRITE_SEQUENCER_410 0x319A
+#define WM8996_WRITE_SEQUENCER_411 0x319B
+#define WM8996_WRITE_SEQUENCER_412 0x319C
+#define WM8996_WRITE_SEQUENCER_413 0x319D
+#define WM8996_WRITE_SEQUENCER_414 0x319E
+#define WM8996_WRITE_SEQUENCER_415 0x319F
+#define WM8996_WRITE_SEQUENCER_416 0x31A0
+#define WM8996_WRITE_SEQUENCER_417 0x31A1
+#define WM8996_WRITE_SEQUENCER_418 0x31A2
+#define WM8996_WRITE_SEQUENCER_419 0x31A3
+#define WM8996_WRITE_SEQUENCER_420 0x31A4
+#define WM8996_WRITE_SEQUENCER_421 0x31A5
+#define WM8996_WRITE_SEQUENCER_422 0x31A6
+#define WM8996_WRITE_SEQUENCER_423 0x31A7
+#define WM8996_WRITE_SEQUENCER_424 0x31A8
+#define WM8996_WRITE_SEQUENCER_425 0x31A9
+#define WM8996_WRITE_SEQUENCER_426 0x31AA
+#define WM8996_WRITE_SEQUENCER_427 0x31AB
+#define WM8996_WRITE_SEQUENCER_428 0x31AC
+#define WM8996_WRITE_SEQUENCER_429 0x31AD
+#define WM8996_WRITE_SEQUENCER_430 0x31AE
+#define WM8996_WRITE_SEQUENCER_431 0x31AF
+#define WM8996_WRITE_SEQUENCER_432 0x31B0
+#define WM8996_WRITE_SEQUENCER_433 0x31B1
+#define WM8996_WRITE_SEQUENCER_434 0x31B2
+#define WM8996_WRITE_SEQUENCER_435 0x31B3
+#define WM8996_WRITE_SEQUENCER_436 0x31B4
+#define WM8996_WRITE_SEQUENCER_437 0x31B5
+#define WM8996_WRITE_SEQUENCER_438 0x31B6
+#define WM8996_WRITE_SEQUENCER_439 0x31B7
+#define WM8996_WRITE_SEQUENCER_440 0x31B8
+#define WM8996_WRITE_SEQUENCER_441 0x31B9
+#define WM8996_WRITE_SEQUENCER_442 0x31BA
+#define WM8996_WRITE_SEQUENCER_443 0x31BB
+#define WM8996_WRITE_SEQUENCER_444 0x31BC
+#define WM8996_WRITE_SEQUENCER_445 0x31BD
+#define WM8996_WRITE_SEQUENCER_446 0x31BE
+#define WM8996_WRITE_SEQUENCER_447 0x31BF
+#define WM8996_WRITE_SEQUENCER_448 0x31C0
+#define WM8996_WRITE_SEQUENCER_449 0x31C1
+#define WM8996_WRITE_SEQUENCER_450 0x31C2
+#define WM8996_WRITE_SEQUENCER_451 0x31C3
+#define WM8996_WRITE_SEQUENCER_452 0x31C4
+#define WM8996_WRITE_SEQUENCER_453 0x31C5
+#define WM8996_WRITE_SEQUENCER_454 0x31C6
+#define WM8996_WRITE_SEQUENCER_455 0x31C7
+#define WM8996_WRITE_SEQUENCER_456 0x31C8
+#define WM8996_WRITE_SEQUENCER_457 0x31C9
+#define WM8996_WRITE_SEQUENCER_458 0x31CA
+#define WM8996_WRITE_SEQUENCER_459 0x31CB
+#define WM8996_WRITE_SEQUENCER_460 0x31CC
+#define WM8996_WRITE_SEQUENCER_461 0x31CD
+#define WM8996_WRITE_SEQUENCER_462 0x31CE
+#define WM8996_WRITE_SEQUENCER_463 0x31CF
+#define WM8996_WRITE_SEQUENCER_464 0x31D0
+#define WM8996_WRITE_SEQUENCER_465 0x31D1
+#define WM8996_WRITE_SEQUENCER_466 0x31D2
+#define WM8996_WRITE_SEQUENCER_467 0x31D3
+#define WM8996_WRITE_SEQUENCER_468 0x31D4
+#define WM8996_WRITE_SEQUENCER_469 0x31D5
+#define WM8996_WRITE_SEQUENCER_470 0x31D6
+#define WM8996_WRITE_SEQUENCER_471 0x31D7
+#define WM8996_WRITE_SEQUENCER_472 0x31D8
+#define WM8996_WRITE_SEQUENCER_473 0x31D9
+#define WM8996_WRITE_SEQUENCER_474 0x31DA
+#define WM8996_WRITE_SEQUENCER_475 0x31DB
+#define WM8996_WRITE_SEQUENCER_476 0x31DC
+#define WM8996_WRITE_SEQUENCER_477 0x31DD
+#define WM8996_WRITE_SEQUENCER_478 0x31DE
+#define WM8996_WRITE_SEQUENCER_479 0x31DF
+#define WM8996_WRITE_SEQUENCER_480 0x31E0
+#define WM8996_WRITE_SEQUENCER_481 0x31E1
+#define WM8996_WRITE_SEQUENCER_482 0x31E2
+#define WM8996_WRITE_SEQUENCER_483 0x31E3
+#define WM8996_WRITE_SEQUENCER_484 0x31E4
+#define WM8996_WRITE_SEQUENCER_485 0x31E5
+#define WM8996_WRITE_SEQUENCER_486 0x31E6
+#define WM8996_WRITE_SEQUENCER_487 0x31E7
+#define WM8996_WRITE_SEQUENCER_488 0x31E8
+#define WM8996_WRITE_SEQUENCER_489 0x31E9
+#define WM8996_WRITE_SEQUENCER_490 0x31EA
+#define WM8996_WRITE_SEQUENCER_491 0x31EB
+#define WM8996_WRITE_SEQUENCER_492 0x31EC
+#define WM8996_WRITE_SEQUENCER_493 0x31ED
+#define WM8996_WRITE_SEQUENCER_494 0x31EE
+#define WM8996_WRITE_SEQUENCER_495 0x31EF
+#define WM8996_WRITE_SEQUENCER_496 0x31F0
+#define WM8996_WRITE_SEQUENCER_497 0x31F1
+#define WM8996_WRITE_SEQUENCER_498 0x31F2
+#define WM8996_WRITE_SEQUENCER_499 0x31F3
+#define WM8996_WRITE_SEQUENCER_500 0x31F4
+#define WM8996_WRITE_SEQUENCER_501 0x31F5
+#define WM8996_WRITE_SEQUENCER_502 0x31F6
+#define WM8996_WRITE_SEQUENCER_503 0x31F7
+#define WM8996_WRITE_SEQUENCER_504 0x31F8
+#define WM8996_WRITE_SEQUENCER_505 0x31F9
+#define WM8996_WRITE_SEQUENCER_506 0x31FA
+#define WM8996_WRITE_SEQUENCER_507 0x31FB
+#define WM8996_WRITE_SEQUENCER_508 0x31FC
+#define WM8996_WRITE_SEQUENCER_509 0x31FD
+#define WM8996_WRITE_SEQUENCER_510 0x31FE
+#define WM8996_WRITE_SEQUENCER_511 0x31FF
+
+#define WM8996_REGISTER_COUNT 706
+#define WM8996_MAX_REGISTER 0x31FF
+
+/*
+ * Field Definitions.
+ */
+
+/*
+ * R0 (0x00) - Software Reset
+ */
+#define WM8996_SW_RESET_MASK 0xFFFF /* SW_RESET - [15:0] */
+#define WM8996_SW_RESET_SHIFT 0 /* SW_RESET - [15:0] */
+#define WM8996_SW_RESET_WIDTH 16 /* SW_RESET - [15:0] */
+
+/*
+ * R1 (0x01) - Power Management (1)
+ */
+#define WM8996_MICB2_ENA 0x0200 /* MICB2_ENA */
+#define WM8996_MICB2_ENA_MASK 0x0200 /* MICB2_ENA */
+#define WM8996_MICB2_ENA_SHIFT 9 /* MICB2_ENA */
+#define WM8996_MICB2_ENA_WIDTH 1 /* MICB2_ENA */
+#define WM8996_MICB1_ENA 0x0100 /* MICB1_ENA */
+#define WM8996_MICB1_ENA_MASK 0x0100 /* MICB1_ENA */
+#define WM8996_MICB1_ENA_SHIFT 8 /* MICB1_ENA */
+#define WM8996_MICB1_ENA_WIDTH 1 /* MICB1_ENA */
+#define WM8996_HPOUT2L_ENA 0x0080 /* HPOUT2L_ENA */
+#define WM8996_HPOUT2L_ENA_MASK 0x0080 /* HPOUT2L_ENA */
+#define WM8996_HPOUT2L_ENA_SHIFT 7 /* HPOUT2L_ENA */
+#define WM8996_HPOUT2L_ENA_WIDTH 1 /* HPOUT2L_ENA */
+#define WM8996_HPOUT2R_ENA 0x0040 /* HPOUT2R_ENA */
+#define WM8996_HPOUT2R_ENA_MASK 0x0040 /* HPOUT2R_ENA */
+#define WM8996_HPOUT2R_ENA_SHIFT 6 /* HPOUT2R_ENA */
+#define WM8996_HPOUT2R_ENA_WIDTH 1 /* HPOUT2R_ENA */
+#define WM8996_HPOUT1L_ENA 0x0020 /* HPOUT1L_ENA */
+#define WM8996_HPOUT1L_ENA_MASK 0x0020 /* HPOUT1L_ENA */
+#define WM8996_HPOUT1L_ENA_SHIFT 5 /* HPOUT1L_ENA */
+#define WM8996_HPOUT1L_ENA_WIDTH 1 /* HPOUT1L_ENA */
+#define WM8996_HPOUT1R_ENA 0x0010 /* HPOUT1R_ENA */
+#define WM8996_HPOUT1R_ENA_MASK 0x0010 /* HPOUT1R_ENA */
+#define WM8996_HPOUT1R_ENA_SHIFT 4 /* HPOUT1R_ENA */
+#define WM8996_HPOUT1R_ENA_WIDTH 1 /* HPOUT1R_ENA */
+#define WM8996_BG_ENA 0x0001 /* BG_ENA */
+#define WM8996_BG_ENA_MASK 0x0001 /* BG_ENA */
+#define WM8996_BG_ENA_SHIFT 0 /* BG_ENA */
+#define WM8996_BG_ENA_WIDTH 1 /* BG_ENA */
+
+/*
+ * R2 (0x02) - Power Management (2)
+ */
+#define WM8996_OPCLK_ENA 0x0800 /* OPCLK_ENA */
+#define WM8996_OPCLK_ENA_MASK 0x0800 /* OPCLK_ENA */
+#define WM8996_OPCLK_ENA_SHIFT 11 /* OPCLK_ENA */
+#define WM8996_OPCLK_ENA_WIDTH 1 /* OPCLK_ENA */
+#define WM8996_INL_ENA 0x0020 /* INL_ENA */
+#define WM8996_INL_ENA_MASK 0x0020 /* INL_ENA */
+#define WM8996_INL_ENA_SHIFT 5 /* INL_ENA */
+#define WM8996_INL_ENA_WIDTH 1 /* INL_ENA */
+#define WM8996_INR_ENA 0x0010 /* INR_ENA */
+#define WM8996_INR_ENA_MASK 0x0010 /* INR_ENA */
+#define WM8996_INR_ENA_SHIFT 4 /* INR_ENA */
+#define WM8996_INR_ENA_WIDTH 1 /* INR_ENA */
+#define WM8996_LDO2_ENA 0x0002 /* LDO2_ENA */
+#define WM8996_LDO2_ENA_MASK 0x0002 /* LDO2_ENA */
+#define WM8996_LDO2_ENA_SHIFT 1 /* LDO2_ENA */
+#define WM8996_LDO2_ENA_WIDTH 1 /* LDO2_ENA */
+
+/*
+ * R3 (0x03) - Power Management (3)
+ */
+#define WM8996_DSP2RXL_ENA 0x0800 /* DSP2RXL_ENA */
+#define WM8996_DSP2RXL_ENA_MASK 0x0800 /* DSP2RXL_ENA */
+#define WM8996_DSP2RXL_ENA_SHIFT 11 /* DSP2RXL_ENA */
+#define WM8996_DSP2RXL_ENA_WIDTH 1 /* DSP2RXL_ENA */
+#define WM8996_DSP2RXR_ENA 0x0400 /* DSP2RXR_ENA */
+#define WM8996_DSP2RXR_ENA_MASK 0x0400 /* DSP2RXR_ENA */
+#define WM8996_DSP2RXR_ENA_SHIFT 10 /* DSP2RXR_ENA */
+#define WM8996_DSP2RXR_ENA_WIDTH 1 /* DSP2RXR_ENA */
+#define WM8996_DSP1RXL_ENA 0x0200 /* DSP1RXL_ENA */
+#define WM8996_DSP1RXL_ENA_MASK 0x0200 /* DSP1RXL_ENA */
+#define WM8996_DSP1RXL_ENA_SHIFT 9 /* DSP1RXL_ENA */
+#define WM8996_DSP1RXL_ENA_WIDTH 1 /* DSP1RXL_ENA */
+#define WM8996_DSP1RXR_ENA 0x0100 /* DSP1RXR_ENA */
+#define WM8996_DSP1RXR_ENA_MASK 0x0100 /* DSP1RXR_ENA */
+#define WM8996_DSP1RXR_ENA_SHIFT 8 /* DSP1RXR_ENA */
+#define WM8996_DSP1RXR_ENA_WIDTH 1 /* DSP1RXR_ENA */
+#define WM8996_DMIC2L_ENA 0x0020 /* DMIC2L_ENA */
+#define WM8996_DMIC2L_ENA_MASK 0x0020 /* DMIC2L_ENA */
+#define WM8996_DMIC2L_ENA_SHIFT 5 /* DMIC2L_ENA */
+#define WM8996_DMIC2L_ENA_WIDTH 1 /* DMIC2L_ENA */
+#define WM8996_DMIC2R_ENA 0x0010 /* DMIC2R_ENA */
+#define WM8996_DMIC2R_ENA_MASK 0x0010 /* DMIC2R_ENA */
+#define WM8996_DMIC2R_ENA_SHIFT 4 /* DMIC2R_ENA */
+#define WM8996_DMIC2R_ENA_WIDTH 1 /* DMIC2R_ENA */
+#define WM8996_DMIC1L_ENA 0x0008 /* DMIC1L_ENA */
+#define WM8996_DMIC1L_ENA_MASK 0x0008 /* DMIC1L_ENA */
+#define WM8996_DMIC1L_ENA_SHIFT 3 /* DMIC1L_ENA */
+#define WM8996_DMIC1L_ENA_WIDTH 1 /* DMIC1L_ENA */
+#define WM8996_DMIC1R_ENA 0x0004 /* DMIC1R_ENA */
+#define WM8996_DMIC1R_ENA_MASK 0x0004 /* DMIC1R_ENA */
+#define WM8996_DMIC1R_ENA_SHIFT 2 /* DMIC1R_ENA */
+#define WM8996_DMIC1R_ENA_WIDTH 1 /* DMIC1R_ENA */
+#define WM8996_ADCL_ENA 0x0002 /* ADCL_ENA */
+#define WM8996_ADCL_ENA_MASK 0x0002 /* ADCL_ENA */
+#define WM8996_ADCL_ENA_SHIFT 1 /* ADCL_ENA */
+#define WM8996_ADCL_ENA_WIDTH 1 /* ADCL_ENA */
+#define WM8996_ADCR_ENA 0x0001 /* ADCR_ENA */
+#define WM8996_ADCR_ENA_MASK 0x0001 /* ADCR_ENA */
+#define WM8996_ADCR_ENA_SHIFT 0 /* ADCR_ENA */
+#define WM8996_ADCR_ENA_WIDTH 1 /* ADCR_ENA */
+
+/*
+ * R4 (0x04) - Power Management (4)
+ */
+#define WM8996_AIF2RX_CHAN1_ENA 0x0200 /* AIF2RX_CHAN1_ENA */
+#define WM8996_AIF2RX_CHAN1_ENA_MASK 0x0200 /* AIF2RX_CHAN1_ENA */
+#define WM8996_AIF2RX_CHAN1_ENA_SHIFT 9 /* AIF2RX_CHAN1_ENA */
+#define WM8996_AIF2RX_CHAN1_ENA_WIDTH 1 /* AIF2RX_CHAN1_ENA */
+#define WM8996_AIF2RX_CHAN0_ENA 0x0100 /* AIF2RX_CHAN0_ENA */
+#define WM8996_AIF2RX_CHAN0_ENA_MASK 0x0100 /* AIF2RX_CHAN0_ENA */
+#define WM8996_AIF2RX_CHAN0_ENA_SHIFT 8 /* AIF2RX_CHAN0_ENA */
+#define WM8996_AIF2RX_CHAN0_ENA_WIDTH 1 /* AIF2RX_CHAN0_ENA */
+#define WM8996_AIF1RX_CHAN5_ENA 0x0020 /* AIF1RX_CHAN5_ENA */
+#define WM8996_AIF1RX_CHAN5_ENA_MASK 0x0020 /* AIF1RX_CHAN5_ENA */
+#define WM8996_AIF1RX_CHAN5_ENA_SHIFT 5 /* AIF1RX_CHAN5_ENA */
+#define WM8996_AIF1RX_CHAN5_ENA_WIDTH 1 /* AIF1RX_CHAN5_ENA */
+#define WM8996_AIF1RX_CHAN4_ENA 0x0010 /* AIF1RX_CHAN4_ENA */
+#define WM8996_AIF1RX_CHAN4_ENA_MASK 0x0010 /* AIF1RX_CHAN4_ENA */
+#define WM8996_AIF1RX_CHAN4_ENA_SHIFT 4 /* AIF1RX_CHAN4_ENA */
+#define WM8996_AIF1RX_CHAN4_ENA_WIDTH 1 /* AIF1RX_CHAN4_ENA */
+#define WM8996_AIF1RX_CHAN3_ENA 0x0008 /* AIF1RX_CHAN3_ENA */
+#define WM8996_AIF1RX_CHAN3_ENA_MASK 0x0008 /* AIF1RX_CHAN3_ENA */
+#define WM8996_AIF1RX_CHAN3_ENA_SHIFT 3 /* AIF1RX_CHAN3_ENA */
+#define WM8996_AIF1RX_CHAN3_ENA_WIDTH 1 /* AIF1RX_CHAN3_ENA */
+#define WM8996_AIF1RX_CHAN2_ENA 0x0004 /* AIF1RX_CHAN2_ENA */
+#define WM8996_AIF1RX_CHAN2_ENA_MASK 0x0004 /* AIF1RX_CHAN2_ENA */
+#define WM8996_AIF1RX_CHAN2_ENA_SHIFT 2 /* AIF1RX_CHAN2_ENA */
+#define WM8996_AIF1RX_CHAN2_ENA_WIDTH 1 /* AIF1RX_CHAN2_ENA */
+#define WM8996_AIF1RX_CHAN1_ENA 0x0002 /* AIF1RX_CHAN1_ENA */
+#define WM8996_AIF1RX_CHAN1_ENA_MASK 0x0002 /* AIF1RX_CHAN1_ENA */
+#define WM8996_AIF1RX_CHAN1_ENA_SHIFT 1 /* AIF1RX_CHAN1_ENA */
+#define WM8996_AIF1RX_CHAN1_ENA_WIDTH 1 /* AIF1RX_CHAN1_ENA */
+#define WM8996_AIF1RX_CHAN0_ENA 0x0001 /* AIF1RX_CHAN0_ENA */
+#define WM8996_AIF1RX_CHAN0_ENA_MASK 0x0001 /* AIF1RX_CHAN0_ENA */
+#define WM8996_AIF1RX_CHAN0_ENA_SHIFT 0 /* AIF1RX_CHAN0_ENA */
+#define WM8996_AIF1RX_CHAN0_ENA_WIDTH 1 /* AIF1RX_CHAN0_ENA */
+
+/*
+ * R5 (0x05) - Power Management (5)
+ */
+#define WM8996_DSP2TXL_ENA 0x0800 /* DSP2TXL_ENA */
+#define WM8996_DSP2TXL_ENA_MASK 0x0800 /* DSP2TXL_ENA */
+#define WM8996_DSP2TXL_ENA_SHIFT 11 /* DSP2TXL_ENA */
+#define WM8996_DSP2TXL_ENA_WIDTH 1 /* DSP2TXL_ENA */
+#define WM8996_DSP2TXR_ENA 0x0400 /* DSP2TXR_ENA */
+#define WM8996_DSP2TXR_ENA_MASK 0x0400 /* DSP2TXR_ENA */
+#define WM8996_DSP2TXR_ENA_SHIFT 10 /* DSP2TXR_ENA */
+#define WM8996_DSP2TXR_ENA_WIDTH 1 /* DSP2TXR_ENA */
+#define WM8996_DSP1TXL_ENA 0x0200 /* DSP1TXL_ENA */
+#define WM8996_DSP1TXL_ENA_MASK 0x0200 /* DSP1TXL_ENA */
+#define WM8996_DSP1TXL_ENA_SHIFT 9 /* DSP1TXL_ENA */
+#define WM8996_DSP1TXL_ENA_WIDTH 1 /* DSP1TXL_ENA */
+#define WM8996_DSP1TXR_ENA 0x0100 /* DSP1TXR_ENA */
+#define WM8996_DSP1TXR_ENA_MASK 0x0100 /* DSP1TXR_ENA */
+#define WM8996_DSP1TXR_ENA_SHIFT 8 /* DSP1TXR_ENA */
+#define WM8996_DSP1TXR_ENA_WIDTH 1 /* DSP1TXR_ENA */
+#define WM8996_DAC2L_ENA 0x0008 /* DAC2L_ENA */
+#define WM8996_DAC2L_ENA_MASK 0x0008 /* DAC2L_ENA */
+#define WM8996_DAC2L_ENA_SHIFT 3 /* DAC2L_ENA */
+#define WM8996_DAC2L_ENA_WIDTH 1 /* DAC2L_ENA */
+#define WM8996_DAC2R_ENA 0x0004 /* DAC2R_ENA */
+#define WM8996_DAC2R_ENA_MASK 0x0004 /* DAC2R_ENA */
+#define WM8996_DAC2R_ENA_SHIFT 2 /* DAC2R_ENA */
+#define WM8996_DAC2R_ENA_WIDTH 1 /* DAC2R_ENA */
+#define WM8996_DAC1L_ENA 0x0002 /* DAC1L_ENA */
+#define WM8996_DAC1L_ENA_MASK 0x0002 /* DAC1L_ENA */
+#define WM8996_DAC1L_ENA_SHIFT 1 /* DAC1L_ENA */
+#define WM8996_DAC1L_ENA_WIDTH 1 /* DAC1L_ENA */
+#define WM8996_DAC1R_ENA 0x0001 /* DAC1R_ENA */
+#define WM8996_DAC1R_ENA_MASK 0x0001 /* DAC1R_ENA */
+#define WM8996_DAC1R_ENA_SHIFT 0 /* DAC1R_ENA */
+#define WM8996_DAC1R_ENA_WIDTH 1 /* DAC1R_ENA */
+
+/*
+ * R6 (0x06) - Power Management (6)
+ */
+#define WM8996_AIF2TX_CHAN1_ENA 0x0200 /* AIF2TX_CHAN1_ENA */
+#define WM8996_AIF2TX_CHAN1_ENA_MASK 0x0200 /* AIF2TX_CHAN1_ENA */
+#define WM8996_AIF2TX_CHAN1_ENA_SHIFT 9 /* AIF2TX_CHAN1_ENA */
+#define WM8996_AIF2TX_CHAN1_ENA_WIDTH 1 /* AIF2TX_CHAN1_ENA */
+#define WM8996_AIF2TX_CHAN0_ENA 0x0100 /* AIF2TX_CHAN0_ENA */
+#define WM8996_AIF2TX_CHAN0_ENA_MASK 0x0100 /* AIF2TX_CHAN0_ENA */
+#define WM8996_AIF2TX_CHAN0_ENA_SHIFT 8 /* AIF2TX_CHAN0_ENA */
+#define WM8996_AIF2TX_CHAN0_ENA_WIDTH 1 /* AIF2TX_CHAN0_ENA */
+#define WM8996_AIF1TX_CHAN5_ENA 0x0020 /* AIF1TX_CHAN5_ENA */
+#define WM8996_AIF1TX_CHAN5_ENA_MASK 0x0020 /* AIF1TX_CHAN5_ENA */
+#define WM8996_AIF1TX_CHAN5_ENA_SHIFT 5 /* AIF1TX_CHAN5_ENA */
+#define WM8996_AIF1TX_CHAN5_ENA_WIDTH 1 /* AIF1TX_CHAN5_ENA */
+#define WM8996_AIF1TX_CHAN4_ENA 0x0010 /* AIF1TX_CHAN4_ENA */
+#define WM8996_AIF1TX_CHAN4_ENA_MASK 0x0010 /* AIF1TX_CHAN4_ENA */
+#define WM8996_AIF1TX_CHAN4_ENA_SHIFT 4 /* AIF1TX_CHAN4_ENA */
+#define WM8996_AIF1TX_CHAN4_ENA_WIDTH 1 /* AIF1TX_CHAN4_ENA */
+#define WM8996_AIF1TX_CHAN3_ENA 0x0008 /* AIF1TX_CHAN3_ENA */
+#define WM8996_AIF1TX_CHAN3_ENA_MASK 0x0008 /* AIF1TX_CHAN3_ENA */
+#define WM8996_AIF1TX_CHAN3_ENA_SHIFT 3 /* AIF1TX_CHAN3_ENA */
+#define WM8996_AIF1TX_CHAN3_ENA_WIDTH 1 /* AIF1TX_CHAN3_ENA */
+#define WM8996_AIF1TX_CHAN2_ENA 0x0004 /* AIF1TX_CHAN2_ENA */
+#define WM8996_AIF1TX_CHAN2_ENA_MASK 0x0004 /* AIF1TX_CHAN2_ENA */
+#define WM8996_AIF1TX_CHAN2_ENA_SHIFT 2 /* AIF1TX_CHAN2_ENA */
+#define WM8996_AIF1TX_CHAN2_ENA_WIDTH 1 /* AIF1TX_CHAN2_ENA */
+#define WM8996_AIF1TX_CHAN1_ENA 0x0002 /* AIF1TX_CHAN1_ENA */
+#define WM8996_AIF1TX_CHAN1_ENA_MASK 0x0002 /* AIF1TX_CHAN1_ENA */
+#define WM8996_AIF1TX_CHAN1_ENA_SHIFT 1 /* AIF1TX_CHAN1_ENA */
+#define WM8996_AIF1TX_CHAN1_ENA_WIDTH 1 /* AIF1TX_CHAN1_ENA */
+#define WM8996_AIF1TX_CHAN0_ENA 0x0001 /* AIF1TX_CHAN0_ENA */
+#define WM8996_AIF1TX_CHAN0_ENA_MASK 0x0001 /* AIF1TX_CHAN0_ENA */
+#define WM8996_AIF1TX_CHAN0_ENA_SHIFT 0 /* AIF1TX_CHAN0_ENA */
+#define WM8996_AIF1TX_CHAN0_ENA_WIDTH 1 /* AIF1TX_CHAN0_ENA */
+
+/*
+ * R7 (0x07) - Power Management (7)
+ */
+#define WM8996_DMIC2_FN 0x0200 /* DMIC2_FN */
+#define WM8996_DMIC2_FN_MASK 0x0200 /* DMIC2_FN */
+#define WM8996_DMIC2_FN_SHIFT 9 /* DMIC2_FN */
+#define WM8996_DMIC2_FN_WIDTH 1 /* DMIC2_FN */
+#define WM8996_DMIC1_FN 0x0100 /* DMIC1_FN */
+#define WM8996_DMIC1_FN_MASK 0x0100 /* DMIC1_FN */
+#define WM8996_DMIC1_FN_SHIFT 8 /* DMIC1_FN */
+#define WM8996_DMIC1_FN_WIDTH 1 /* DMIC1_FN */
+#define WM8996_ADC_DMIC_DSP2R_ENA 0x0080 /* ADC_DMIC_DSP2R_ENA */
+#define WM8996_ADC_DMIC_DSP2R_ENA_MASK 0x0080 /* ADC_DMIC_DSP2R_ENA */
+#define WM8996_ADC_DMIC_DSP2R_ENA_SHIFT 7 /* ADC_DMIC_DSP2R_ENA */
+#define WM8996_ADC_DMIC_DSP2R_ENA_WIDTH 1 /* ADC_DMIC_DSP2R_ENA */
+#define WM8996_ADC_DMIC_DSP2L_ENA 0x0040 /* ADC_DMIC_DSP2L_ENA */
+#define WM8996_ADC_DMIC_DSP2L_ENA_MASK 0x0040 /* ADC_DMIC_DSP2L_ENA */
+#define WM8996_ADC_DMIC_DSP2L_ENA_SHIFT 6 /* ADC_DMIC_DSP2L_ENA */
+#define WM8996_ADC_DMIC_DSP2L_ENA_WIDTH 1 /* ADC_DMIC_DSP2L_ENA */
+#define WM8996_ADC_DMIC_SRC2_MASK 0x0030 /* ADC_DMIC_SRC2 - [5:4] */
+#define WM8996_ADC_DMIC_SRC2_SHIFT 4 /* ADC_DMIC_SRC2 - [5:4] */
+#define WM8996_ADC_DMIC_SRC2_WIDTH 2 /* ADC_DMIC_SRC2 - [5:4] */
+#define WM8996_ADC_DMIC_DSP1R_ENA 0x0008 /* ADC_DMIC_DSP1R_ENA */
+#define WM8996_ADC_DMIC_DSP1R_ENA_MASK 0x0008 /* ADC_DMIC_DSP1R_ENA */
+#define WM8996_ADC_DMIC_DSP1R_ENA_SHIFT 3 /* ADC_DMIC_DSP1R_ENA */
+#define WM8996_ADC_DMIC_DSP1R_ENA_WIDTH 1 /* ADC_DMIC_DSP1R_ENA */
+#define WM8996_ADC_DMIC_DSP1L_ENA 0x0004 /* ADC_DMIC_DSP1L_ENA */
+#define WM8996_ADC_DMIC_DSP1L_ENA_MASK 0x0004 /* ADC_DMIC_DSP1L_ENA */
+#define WM8996_ADC_DMIC_DSP1L_ENA_SHIFT 2 /* ADC_DMIC_DSP1L_ENA */
+#define WM8996_ADC_DMIC_DSP1L_ENA_WIDTH 1 /* ADC_DMIC_DSP1L_ENA */
+#define WM8996_ADC_DMIC_SRC1_MASK 0x0003 /* ADC_DMIC_SRC1 - [1:0] */
+#define WM8996_ADC_DMIC_SRC1_SHIFT 0 /* ADC_DMIC_SRC1 - [1:0] */
+#define WM8996_ADC_DMIC_SRC1_WIDTH 2 /* ADC_DMIC_SRC1 - [1:0] */
+
+/*
+ * R8 (0x08) - Power Management (8)
+ */
+#define WM8996_AIF2TX_SRC_MASK 0x00C0 /* AIF2TX_SRC - [7:6] */
+#define WM8996_AIF2TX_SRC_SHIFT 6 /* AIF2TX_SRC - [7:6] */
+#define WM8996_AIF2TX_SRC_WIDTH 2 /* AIF2TX_SRC - [7:6] */
+#define WM8996_DSP2RX_SRC 0x0010 /* DSP2RX_SRC */
+#define WM8996_DSP2RX_SRC_MASK 0x0010 /* DSP2RX_SRC */
+#define WM8996_DSP2RX_SRC_SHIFT 4 /* DSP2RX_SRC */
+#define WM8996_DSP2RX_SRC_WIDTH 1 /* DSP2RX_SRC */
+#define WM8996_DSP1RX_SRC 0x0001 /* DSP1RX_SRC */
+#define WM8996_DSP1RX_SRC_MASK 0x0001 /* DSP1RX_SRC */
+#define WM8996_DSP1RX_SRC_SHIFT 0 /* DSP1RX_SRC */
+#define WM8996_DSP1RX_SRC_WIDTH 1 /* DSP1RX_SRC */
+
+/*
+ * R16 (0x10) - Left Line Input Volume
+ */
+#define WM8996_IN1_VU 0x0080 /* IN1_VU */
+#define WM8996_IN1_VU_MASK 0x0080 /* IN1_VU */
+#define WM8996_IN1_VU_SHIFT 7 /* IN1_VU */
+#define WM8996_IN1_VU_WIDTH 1 /* IN1_VU */
+#define WM8996_IN1L_ZC 0x0020 /* IN1L_ZC */
+#define WM8996_IN1L_ZC_MASK 0x0020 /* IN1L_ZC */
+#define WM8996_IN1L_ZC_SHIFT 5 /* IN1L_ZC */
+#define WM8996_IN1L_ZC_WIDTH 1 /* IN1L_ZC */
+#define WM8996_IN1L_VOL_MASK 0x001F /* IN1L_VOL - [4:0] */
+#define WM8996_IN1L_VOL_SHIFT 0 /* IN1L_VOL - [4:0] */
+#define WM8996_IN1L_VOL_WIDTH 5 /* IN1L_VOL - [4:0] */
+
+/*
+ * R17 (0x11) - Right Line Input Volume
+ */
+#define WM8996_IN1_VU 0x0080 /* IN1_VU */
+#define WM8996_IN1_VU_MASK 0x0080 /* IN1_VU */
+#define WM8996_IN1_VU_SHIFT 7 /* IN1_VU */
+#define WM8996_IN1_VU_WIDTH 1 /* IN1_VU */
+#define WM8996_IN1R_ZC 0x0020 /* IN1R_ZC */
+#define WM8996_IN1R_ZC_MASK 0x0020 /* IN1R_ZC */
+#define WM8996_IN1R_ZC_SHIFT 5 /* IN1R_ZC */
+#define WM8996_IN1R_ZC_WIDTH 1 /* IN1R_ZC */
+#define WM8996_IN1R_VOL_MASK 0x001F /* IN1R_VOL - [4:0] */
+#define WM8996_IN1R_VOL_SHIFT 0 /* IN1R_VOL - [4:0] */
+#define WM8996_IN1R_VOL_WIDTH 5 /* IN1R_VOL - [4:0] */
+
+/*
+ * R18 (0x12) - Line Input Control
+ */
+#define WM8996_INL_MODE_MASK 0x000C /* INL_MODE - [3:2] */
+#define WM8996_INL_MODE_SHIFT 2 /* INL_MODE - [3:2] */
+#define WM8996_INL_MODE_WIDTH 2 /* INL_MODE - [3:2] */
+#define WM8996_INR_MODE_MASK 0x0003 /* INR_MODE - [1:0] */
+#define WM8996_INR_MODE_SHIFT 0 /* INR_MODE - [1:0] */
+#define WM8996_INR_MODE_WIDTH 2 /* INR_MODE - [1:0] */
+
+/*
+ * R21 (0x15) - DAC1 HPOUT1 Volume
+ */
+#define WM8996_DAC1R_HPOUT1R_VOL_MASK 0x00F0 /* DAC1R_HPOUT1R_VOL - [7:4] */
+#define WM8996_DAC1R_HPOUT1R_VOL_SHIFT 4 /* DAC1R_HPOUT1R_VOL - [7:4] */
+#define WM8996_DAC1R_HPOUT1R_VOL_WIDTH 4 /* DAC1R_HPOUT1R_VOL - [7:4] */
+#define WM8996_DAC1L_HPOUT1L_VOL_MASK 0x000F /* DAC1L_HPOUT1L_VOL - [3:0] */
+#define WM8996_DAC1L_HPOUT1L_VOL_SHIFT 0 /* DAC1L_HPOUT1L_VOL - [3:0] */
+#define WM8996_DAC1L_HPOUT1L_VOL_WIDTH 4 /* DAC1L_HPOUT1L_VOL - [3:0] */
+
+/*
+ * R22 (0x16) - DAC2 HPOUT2 Volume
+ */
+#define WM8996_DAC2R_HPOUT2R_VOL_MASK 0x00F0 /* DAC2R_HPOUT2R_VOL - [7:4] */
+#define WM8996_DAC2R_HPOUT2R_VOL_SHIFT 4 /* DAC2R_HPOUT2R_VOL - [7:4] */
+#define WM8996_DAC2R_HPOUT2R_VOL_WIDTH 4 /* DAC2R_HPOUT2R_VOL - [7:4] */
+#define WM8996_DAC2L_HPOUT2L_VOL_MASK 0x000F /* DAC2L_HPOUT2L_VOL - [3:0] */
+#define WM8996_DAC2L_HPOUT2L_VOL_SHIFT 0 /* DAC2L_HPOUT2L_VOL - [3:0] */
+#define WM8996_DAC2L_HPOUT2L_VOL_WIDTH 4 /* DAC2L_HPOUT2L_VOL - [3:0] */
+
+/*
+ * R24 (0x18) - DAC1 Left Volume
+ */
+#define WM8996_DAC1L_MUTE 0x0200 /* DAC1L_MUTE */
+#define WM8996_DAC1L_MUTE_MASK 0x0200 /* DAC1L_MUTE */
+#define WM8996_DAC1L_MUTE_SHIFT 9 /* DAC1L_MUTE */
+#define WM8996_DAC1L_MUTE_WIDTH 1 /* DAC1L_MUTE */
+#define WM8996_DAC1_VU 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_MASK 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_SHIFT 8 /* DAC1_VU */
+#define WM8996_DAC1_VU_WIDTH 1 /* DAC1_VU */
+#define WM8996_DAC1L_VOL_MASK 0x00FF /* DAC1L_VOL - [7:0] */
+#define WM8996_DAC1L_VOL_SHIFT 0 /* DAC1L_VOL - [7:0] */
+#define WM8996_DAC1L_VOL_WIDTH 8 /* DAC1L_VOL - [7:0] */
+
+/*
+ * R25 (0x19) - DAC1 Right Volume
+ */
+#define WM8996_DAC1R_MUTE 0x0200 /* DAC1R_MUTE */
+#define WM8996_DAC1R_MUTE_MASK 0x0200 /* DAC1R_MUTE */
+#define WM8996_DAC1R_MUTE_SHIFT 9 /* DAC1R_MUTE */
+#define WM8996_DAC1R_MUTE_WIDTH 1 /* DAC1R_MUTE */
+#define WM8996_DAC1_VU 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_MASK 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_SHIFT 8 /* DAC1_VU */
+#define WM8996_DAC1_VU_WIDTH 1 /* DAC1_VU */
+#define WM8996_DAC1R_VOL_MASK 0x00FF /* DAC1R_VOL - [7:0] */
+#define WM8996_DAC1R_VOL_SHIFT 0 /* DAC1R_VOL - [7:0] */
+#define WM8996_DAC1R_VOL_WIDTH 8 /* DAC1R_VOL - [7:0] */
+
+/*
+ * R26 (0x1A) - DAC2 Left Volume
+ */
+#define WM8996_DAC2L_MUTE 0x0200 /* DAC2L_MUTE */
+#define WM8996_DAC2L_MUTE_MASK 0x0200 /* DAC2L_MUTE */
+#define WM8996_DAC2L_MUTE_SHIFT 9 /* DAC2L_MUTE */
+#define WM8996_DAC2L_MUTE_WIDTH 1 /* DAC2L_MUTE */
+#define WM8996_DAC2_VU 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_MASK 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_SHIFT 8 /* DAC2_VU */
+#define WM8996_DAC2_VU_WIDTH 1 /* DAC2_VU */
+#define WM8996_DAC2L_VOL_MASK 0x00FF /* DAC2L_VOL - [7:0] */
+#define WM8996_DAC2L_VOL_SHIFT 0 /* DAC2L_VOL - [7:0] */
+#define WM8996_DAC2L_VOL_WIDTH 8 /* DAC2L_VOL - [7:0] */
+
+/*
+ * R27 (0x1B) - DAC2 Right Volume
+ */
+#define WM8996_DAC2R_MUTE 0x0200 /* DAC2R_MUTE */
+#define WM8996_DAC2R_MUTE_MASK 0x0200 /* DAC2R_MUTE */
+#define WM8996_DAC2R_MUTE_SHIFT 9 /* DAC2R_MUTE */
+#define WM8996_DAC2R_MUTE_WIDTH 1 /* DAC2R_MUTE */
+#define WM8996_DAC2_VU 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_MASK 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_SHIFT 8 /* DAC2_VU */
+#define WM8996_DAC2_VU_WIDTH 1 /* DAC2_VU */
+#define WM8996_DAC2R_VOL_MASK 0x00FF /* DAC2R_VOL - [7:0] */
+#define WM8996_DAC2R_VOL_SHIFT 0 /* DAC2R_VOL - [7:0] */
+#define WM8996_DAC2R_VOL_WIDTH 8 /* DAC2R_VOL - [7:0] */
+
+/*
+ * R28 (0x1C) - Output1 Left Volume
+ */
+#define WM8996_DAC1_VU 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_MASK 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_SHIFT 8 /* DAC1_VU */
+#define WM8996_DAC1_VU_WIDTH 1 /* DAC1_VU */
+#define WM8996_HPOUT1L_ZC 0x0080 /* HPOUT1L_ZC */
+#define WM8996_HPOUT1L_ZC_MASK 0x0080 /* HPOUT1L_ZC */
+#define WM8996_HPOUT1L_ZC_SHIFT 7 /* HPOUT1L_ZC */
+#define WM8996_HPOUT1L_ZC_WIDTH 1 /* HPOUT1L_ZC */
+#define WM8996_HPOUT1L_VOL_MASK 0x000F /* HPOUT1L_VOL - [3:0] */
+#define WM8996_HPOUT1L_VOL_SHIFT 0 /* HPOUT1L_VOL - [3:0] */
+#define WM8996_HPOUT1L_VOL_WIDTH 4 /* HPOUT1L_VOL - [3:0] */
+
+/*
+ * R29 (0x1D) - Output1 Right Volume
+ */
+#define WM8996_DAC1_VU 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_MASK 0x0100 /* DAC1_VU */
+#define WM8996_DAC1_VU_SHIFT 8 /* DAC1_VU */
+#define WM8996_DAC1_VU_WIDTH 1 /* DAC1_VU */
+#define WM8996_HPOUT1R_ZC 0x0080 /* HPOUT1R_ZC */
+#define WM8996_HPOUT1R_ZC_MASK 0x0080 /* HPOUT1R_ZC */
+#define WM8996_HPOUT1R_ZC_SHIFT 7 /* HPOUT1R_ZC */
+#define WM8996_HPOUT1R_ZC_WIDTH 1 /* HPOUT1R_ZC */
+#define WM8996_HPOUT1R_VOL_MASK 0x000F /* HPOUT1R_VOL - [3:0] */
+#define WM8996_HPOUT1R_VOL_SHIFT 0 /* HPOUT1R_VOL - [3:0] */
+#define WM8996_HPOUT1R_VOL_WIDTH 4 /* HPOUT1R_VOL - [3:0] */
+
+/*
+ * R30 (0x1E) - Output2 Left Volume
+ */
+#define WM8996_DAC2_VU 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_MASK 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_SHIFT 8 /* DAC2_VU */
+#define WM8996_DAC2_VU_WIDTH 1 /* DAC2_VU */
+#define WM8996_HPOUT2L_ZC 0x0080 /* HPOUT2L_ZC */
+#define WM8996_HPOUT2L_ZC_MASK 0x0080 /* HPOUT2L_ZC */
+#define WM8996_HPOUT2L_ZC_SHIFT 7 /* HPOUT2L_ZC */
+#define WM8996_HPOUT2L_ZC_WIDTH 1 /* HPOUT2L_ZC */
+#define WM8996_HPOUT2L_VOL_MASK 0x000F /* HPOUT2L_VOL - [3:0] */
+#define WM8996_HPOUT2L_VOL_SHIFT 0 /* HPOUT2L_VOL - [3:0] */
+#define WM8996_HPOUT2L_VOL_WIDTH 4 /* HPOUT2L_VOL - [3:0] */
+
+/*
+ * R31 (0x1F) - Output2 Right Volume
+ */
+#define WM8996_DAC2_VU 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_MASK 0x0100 /* DAC2_VU */
+#define WM8996_DAC2_VU_SHIFT 8 /* DAC2_VU */
+#define WM8996_DAC2_VU_WIDTH 1 /* DAC2_VU */
+#define WM8996_HPOUT2R_ZC 0x0080 /* HPOUT2R_ZC */
+#define WM8996_HPOUT2R_ZC_MASK 0x0080 /* HPOUT2R_ZC */
+#define WM8996_HPOUT2R_ZC_SHIFT 7 /* HPOUT2R_ZC */
+#define WM8996_HPOUT2R_ZC_WIDTH 1 /* HPOUT2R_ZC */
+#define WM8996_HPOUT2R_VOL_MASK 0x000F /* HPOUT2R_VOL - [3:0] */
+#define WM8996_HPOUT2R_VOL_SHIFT 0 /* HPOUT2R_VOL - [3:0] */
+#define WM8996_HPOUT2R_VOL_WIDTH 4 /* HPOUT2R_VOL - [3:0] */
+
+/*
+ * R32 (0x20) - MICBIAS (1)
+ */
+#define WM8996_MICB1_RATE 0x0020 /* MICB1_RATE */
+#define WM8996_MICB1_RATE_MASK 0x0020 /* MICB1_RATE */
+#define WM8996_MICB1_RATE_SHIFT 5 /* MICB1_RATE */
+#define WM8996_MICB1_RATE_WIDTH 1 /* MICB1_RATE */
+#define WM8996_MICB1_MODE 0x0010 /* MICB1_MODE */
+#define WM8996_MICB1_MODE_MASK 0x0010 /* MICB1_MODE */
+#define WM8996_MICB1_MODE_SHIFT 4 /* MICB1_MODE */
+#define WM8996_MICB1_MODE_WIDTH 1 /* MICB1_MODE */
+#define WM8996_MICB1_LVL_MASK 0x000E /* MICB1_LVL - [3:1] */
+#define WM8996_MICB1_LVL_SHIFT 1 /* MICB1_LVL - [3:1] */
+#define WM8996_MICB1_LVL_WIDTH 3 /* MICB1_LVL - [3:1] */
+#define WM8996_MICB1_DISCH 0x0001 /* MICB1_DISCH */
+#define WM8996_MICB1_DISCH_MASK 0x0001 /* MICB1_DISCH */
+#define WM8996_MICB1_DISCH_SHIFT 0 /* MICB1_DISCH */
+#define WM8996_MICB1_DISCH_WIDTH 1 /* MICB1_DISCH */
+
+/*
+ * R33 (0x21) - MICBIAS (2)
+ */
+#define WM8996_MICB2_RATE 0x0020 /* MICB2_RATE */
+#define WM8996_MICB2_RATE_MASK 0x0020 /* MICB2_RATE */
+#define WM8996_MICB2_RATE_SHIFT 5 /* MICB2_RATE */
+#define WM8996_MICB2_RATE_WIDTH 1 /* MICB2_RATE */
+#define WM8996_MICB2_MODE 0x0010 /* MICB2_MODE */
+#define WM8996_MICB2_MODE_MASK 0x0010 /* MICB2_MODE */
+#define WM8996_MICB2_MODE_SHIFT 4 /* MICB2_MODE */
+#define WM8996_MICB2_MODE_WIDTH 1 /* MICB2_MODE */
+#define WM8996_MICB2_LVL_MASK 0x000E /* MICB2_LVL - [3:1] */
+#define WM8996_MICB2_LVL_SHIFT 1 /* MICB2_LVL - [3:1] */
+#define WM8996_MICB2_LVL_WIDTH 3 /* MICB2_LVL - [3:1] */
+#define WM8996_MICB2_DISCH 0x0001 /* MICB2_DISCH */
+#define WM8996_MICB2_DISCH_MASK 0x0001 /* MICB2_DISCH */
+#define WM8996_MICB2_DISCH_SHIFT 0 /* MICB2_DISCH */
+#define WM8996_MICB2_DISCH_WIDTH 1 /* MICB2_DISCH */
+
+/*
+ * R40 (0x28) - LDO 1
+ */
+#define WM8996_LDO1_MODE 0x0020 /* LDO1_MODE */
+#define WM8996_LDO1_MODE_MASK 0x0020 /* LDO1_MODE */
+#define WM8996_LDO1_MODE_SHIFT 5 /* LDO1_MODE */
+#define WM8996_LDO1_MODE_WIDTH 1 /* LDO1_MODE */
+#define WM8996_LDO1_VSEL_MASK 0x0006 /* LDO1_VSEL - [2:1] */
+#define WM8996_LDO1_VSEL_SHIFT 1 /* LDO1_VSEL - [2:1] */
+#define WM8996_LDO1_VSEL_WIDTH 2 /* LDO1_VSEL - [2:1] */
+#define WM8996_LDO1_DISCH 0x0001 /* LDO1_DISCH */
+#define WM8996_LDO1_DISCH_MASK 0x0001 /* LDO1_DISCH */
+#define WM8996_LDO1_DISCH_SHIFT 0 /* LDO1_DISCH */
+#define WM8996_LDO1_DISCH_WIDTH 1 /* LDO1_DISCH */
+
+/*
+ * R41 (0x29) - LDO 2
+ */
+#define WM8996_LDO2_MODE 0x0020 /* LDO2_MODE */
+#define WM8996_LDO2_MODE_MASK 0x0020 /* LDO2_MODE */
+#define WM8996_LDO2_MODE_SHIFT 5 /* LDO2_MODE */
+#define WM8996_LDO2_MODE_WIDTH 1 /* LDO2_MODE */
+#define WM8996_LDO2_VSEL_MASK 0x001E /* LDO2_VSEL - [4:1] */
+#define WM8996_LDO2_VSEL_SHIFT 1 /* LDO2_VSEL - [4:1] */
+#define WM8996_LDO2_VSEL_WIDTH 4 /* LDO2_VSEL - [4:1] */
+#define WM8996_LDO2_DISCH 0x0001 /* LDO2_DISCH */
+#define WM8996_LDO2_DISCH_MASK 0x0001 /* LDO2_DISCH */
+#define WM8996_LDO2_DISCH_SHIFT 0 /* LDO2_DISCH */
+#define WM8996_LDO2_DISCH_WIDTH 1 /* LDO2_DISCH */
+
+/*
+ * R48 (0x30) - Accessory Detect Mode 1
+ */
+#define WM8996_JD_MODE_MASK 0x0003 /* JD_MODE - [1:0] */
+#define WM8996_JD_MODE_SHIFT 0 /* JD_MODE - [1:0] */
+#define WM8996_JD_MODE_WIDTH 2 /* JD_MODE - [1:0] */
+
+/*
+ * R49 (0x31) - Accessory Detect Mode 2
+ */
+#define WM8996_HPOUT1FB_SRC 0x0004 /* HPOUT1FB_SRC */
+#define WM8996_HPOUT1FB_SRC_MASK 0x0004 /* HPOUT1FB_SRC */
+#define WM8996_HPOUT1FB_SRC_SHIFT 2 /* HPOUT1FB_SRC */
+#define WM8996_HPOUT1FB_SRC_WIDTH 1 /* HPOUT1FB_SRC */
+#define WM8996_MICD_SRC 0x0002 /* MICD_SRC */
+#define WM8996_MICD_SRC_MASK 0x0002 /* MICD_SRC */
+#define WM8996_MICD_SRC_SHIFT 1 /* MICD_SRC */
+#define WM8996_MICD_SRC_WIDTH 1 /* MICD_SRC */
+#define WM8996_MICD_BIAS_SRC 0x0001 /* MICD_BIAS_SRC */
+#define WM8996_MICD_BIAS_SRC_MASK 0x0001 /* MICD_BIAS_SRC */
+#define WM8996_MICD_BIAS_SRC_SHIFT 0 /* MICD_BIAS_SRC */
+#define WM8996_MICD_BIAS_SRC_WIDTH 1 /* MICD_BIAS_SRC */
+
+/*
+ * R52 (0x34) - Headphone Detect 1
+ */
+#define WM8996_HP_HOLDTIME_MASK 0x00E0 /* HP_HOLDTIME - [7:5] */
+#define WM8996_HP_HOLDTIME_SHIFT 5 /* HP_HOLDTIME - [7:5] */
+#define WM8996_HP_HOLDTIME_WIDTH 3 /* HP_HOLDTIME - [7:5] */
+#define WM8996_HP_CLK_DIV_MASK 0x0018 /* HP_CLK_DIV - [4:3] */
+#define WM8996_HP_CLK_DIV_SHIFT 3 /* HP_CLK_DIV - [4:3] */
+#define WM8996_HP_CLK_DIV_WIDTH 2 /* HP_CLK_DIV - [4:3] */
+#define WM8996_HP_STEP_SIZE 0x0002 /* HP_STEP_SIZE */
+#define WM8996_HP_STEP_SIZE_MASK 0x0002 /* HP_STEP_SIZE */
+#define WM8996_HP_STEP_SIZE_SHIFT 1 /* HP_STEP_SIZE */
+#define WM8996_HP_STEP_SIZE_WIDTH 1 /* HP_STEP_SIZE */
+#define WM8996_HP_POLL 0x0001 /* HP_POLL */
+#define WM8996_HP_POLL_MASK 0x0001 /* HP_POLL */
+#define WM8996_HP_POLL_SHIFT 0 /* HP_POLL */
+#define WM8996_HP_POLL_WIDTH 1 /* HP_POLL */
+
+/*
+ * R53 (0x35) - Headphone Detect 2
+ */
+#define WM8996_HP_DONE 0x0080 /* HP_DONE */
+#define WM8996_HP_DONE_MASK 0x0080 /* HP_DONE */
+#define WM8996_HP_DONE_SHIFT 7 /* HP_DONE */
+#define WM8996_HP_DONE_WIDTH 1 /* HP_DONE */
+#define WM8996_HP_LVL_MASK 0x007F /* HP_LVL - [6:0] */
+#define WM8996_HP_LVL_SHIFT 0 /* HP_LVL - [6:0] */
+#define WM8996_HP_LVL_WIDTH 7 /* HP_LVL - [6:0] */
+
+/*
+ * R56 (0x38) - Mic Detect 1
+ */
+#define WM8996_MICD_BIAS_STARTTIME_MASK 0xF000 /* MICD_BIAS_STARTTIME - [15:12] */
+#define WM8996_MICD_BIAS_STARTTIME_SHIFT 12 /* MICD_BIAS_STARTTIME - [15:12] */
+#define WM8996_MICD_BIAS_STARTTIME_WIDTH 4 /* MICD_BIAS_STARTTIME - [15:12] */
+#define WM8996_MICD_RATE_MASK 0x0F00 /* MICD_RATE - [11:8] */
+#define WM8996_MICD_RATE_SHIFT 8 /* MICD_RATE - [11:8] */
+#define WM8996_MICD_RATE_WIDTH 4 /* MICD_RATE - [11:8] */
+#define WM8996_MICD_DBTIME 0x0002 /* MICD_DBTIME */
+#define WM8996_MICD_DBTIME_MASK 0x0002 /* MICD_DBTIME */
+#define WM8996_MICD_DBTIME_SHIFT 1 /* MICD_DBTIME */
+#define WM8996_MICD_DBTIME_WIDTH 1 /* MICD_DBTIME */
+#define WM8996_MICD_ENA 0x0001 /* MICD_ENA */
+#define WM8996_MICD_ENA_MASK 0x0001 /* MICD_ENA */
+#define WM8996_MICD_ENA_SHIFT 0 /* MICD_ENA */
+#define WM8996_MICD_ENA_WIDTH 1 /* MICD_ENA */
+
+/*
+ * R57 (0x39) - Mic Detect 2
+ */
+#define WM8996_MICD_LVL_SEL_MASK 0x00FF /* MICD_LVL_SEL - [7:0] */
+#define WM8996_MICD_LVL_SEL_SHIFT 0 /* MICD_LVL_SEL - [7:0] */
+#define WM8996_MICD_LVL_SEL_WIDTH 8 /* MICD_LVL_SEL - [7:0] */
+
+/*
+ * R58 (0x3A) - Mic Detect 3
+ */
+#define WM8996_MICD_LVL_MASK 0x07FC /* MICD_LVL - [10:2] */
+#define WM8996_MICD_LVL_SHIFT 2 /* MICD_LVL - [10:2] */
+#define WM8996_MICD_LVL_WIDTH 9 /* MICD_LVL - [10:2] */
+#define WM8996_MICD_VALID 0x0002 /* MICD_VALID */
+#define WM8996_MICD_VALID_MASK 0x0002 /* MICD_VALID */
+#define WM8996_MICD_VALID_SHIFT 1 /* MICD_VALID */
+#define WM8996_MICD_VALID_WIDTH 1 /* MICD_VALID */
+#define WM8996_MICD_STS 0x0001 /* MICD_STS */
+#define WM8996_MICD_STS_MASK 0x0001 /* MICD_STS */
+#define WM8996_MICD_STS_SHIFT 0 /* MICD_STS */
+#define WM8996_MICD_STS_WIDTH 1 /* MICD_STS */
+
+/*
+ * R64 (0x40) - Charge Pump (1)
+ */
+#define WM8996_CP_ENA 0x8000 /* CP_ENA */
+#define WM8996_CP_ENA_MASK 0x8000 /* CP_ENA */
+#define WM8996_CP_ENA_SHIFT 15 /* CP_ENA */
+#define WM8996_CP_ENA_WIDTH 1 /* CP_ENA */
+
+/*
+ * R65 (0x41) - Charge Pump (2)
+ */
+#define WM8996_CP_DISCH 0x8000 /* CP_DISCH */
+#define WM8996_CP_DISCH_MASK 0x8000 /* CP_DISCH */
+#define WM8996_CP_DISCH_SHIFT 15 /* CP_DISCH */
+#define WM8996_CP_DISCH_WIDTH 1 /* CP_DISCH */
+
+/*
+ * R80 (0x50) - DC Servo (1)
+ */
+#define WM8996_DCS_ENA_CHAN_3 0x0008 /* DCS_ENA_CHAN_3 */
+#define WM8996_DCS_ENA_CHAN_3_MASK 0x0008 /* DCS_ENA_CHAN_3 */
+#define WM8996_DCS_ENA_CHAN_3_SHIFT 3 /* DCS_ENA_CHAN_3 */
+#define WM8996_DCS_ENA_CHAN_3_WIDTH 1 /* DCS_ENA_CHAN_3 */
+#define WM8996_DCS_ENA_CHAN_2 0x0004 /* DCS_ENA_CHAN_2 */
+#define WM8996_DCS_ENA_CHAN_2_MASK 0x0004 /* DCS_ENA_CHAN_2 */
+#define WM8996_DCS_ENA_CHAN_2_SHIFT 2 /* DCS_ENA_CHAN_2 */
+#define WM8996_DCS_ENA_CHAN_2_WIDTH 1 /* DCS_ENA_CHAN_2 */
+#define WM8996_DCS_ENA_CHAN_1 0x0002 /* DCS_ENA_CHAN_1 */
+#define WM8996_DCS_ENA_CHAN_1_MASK 0x0002 /* DCS_ENA_CHAN_1 */
+#define WM8996_DCS_ENA_CHAN_1_SHIFT 1 /* DCS_ENA_CHAN_1 */
+#define WM8996_DCS_ENA_CHAN_1_WIDTH 1 /* DCS_ENA_CHAN_1 */
+#define WM8996_DCS_ENA_CHAN_0 0x0001 /* DCS_ENA_CHAN_0 */
+#define WM8996_DCS_ENA_CHAN_0_MASK 0x0001 /* DCS_ENA_CHAN_0 */
+#define WM8996_DCS_ENA_CHAN_0_SHIFT 0 /* DCS_ENA_CHAN_0 */
+#define WM8996_DCS_ENA_CHAN_0_WIDTH 1 /* DCS_ENA_CHAN_0 */
+
+/*
+ * R81 (0x51) - DC Servo (2)
+ */
+#define WM8996_DCS_TRIG_SINGLE_3 0x8000 /* DCS_TRIG_SINGLE_3 */
+#define WM8996_DCS_TRIG_SINGLE_3_MASK 0x8000 /* DCS_TRIG_SINGLE_3 */
+#define WM8996_DCS_TRIG_SINGLE_3_SHIFT 15 /* DCS_TRIG_SINGLE_3 */
+#define WM8996_DCS_TRIG_SINGLE_3_WIDTH 1 /* DCS_TRIG_SINGLE_3 */
+#define WM8996_DCS_TRIG_SINGLE_2 0x4000 /* DCS_TRIG_SINGLE_2 */
+#define WM8996_DCS_TRIG_SINGLE_2_MASK 0x4000 /* DCS_TRIG_SINGLE_2 */
+#define WM8996_DCS_TRIG_SINGLE_2_SHIFT 14 /* DCS_TRIG_SINGLE_2 */
+#define WM8996_DCS_TRIG_SINGLE_2_WIDTH 1 /* DCS_TRIG_SINGLE_2 */
+#define WM8996_DCS_TRIG_SINGLE_1 0x2000 /* DCS_TRIG_SINGLE_1 */
+#define WM8996_DCS_TRIG_SINGLE_1_MASK 0x2000 /* DCS_TRIG_SINGLE_1 */
+#define WM8996_DCS_TRIG_SINGLE_1_SHIFT 13 /* DCS_TRIG_SINGLE_1 */
+#define WM8996_DCS_TRIG_SINGLE_1_WIDTH 1 /* DCS_TRIG_SINGLE_1 */
+#define WM8996_DCS_TRIG_SINGLE_0 0x1000 /* DCS_TRIG_SINGLE_0 */
+#define WM8996_DCS_TRIG_SINGLE_0_MASK 0x1000 /* DCS_TRIG_SINGLE_0 */
+#define WM8996_DCS_TRIG_SINGLE_0_SHIFT 12 /* DCS_TRIG_SINGLE_0 */
+#define WM8996_DCS_TRIG_SINGLE_0_WIDTH 1 /* DCS_TRIG_SINGLE_0 */
+#define WM8996_DCS_TRIG_SERIES_3 0x0800 /* DCS_TRIG_SERIES_3 */
+#define WM8996_DCS_TRIG_SERIES_3_MASK 0x0800 /* DCS_TRIG_SERIES_3 */
+#define WM8996_DCS_TRIG_SERIES_3_SHIFT 11 /* DCS_TRIG_SERIES_3 */
+#define WM8996_DCS_TRIG_SERIES_3_WIDTH 1 /* DCS_TRIG_SERIES_3 */
+#define WM8996_DCS_TRIG_SERIES_2 0x0400 /* DCS_TRIG_SERIES_2 */
+#define WM8996_DCS_TRIG_SERIES_2_MASK 0x0400 /* DCS_TRIG_SERIES_2 */
+#define WM8996_DCS_TRIG_SERIES_2_SHIFT 10 /* DCS_TRIG_SERIES_2 */
+#define WM8996_DCS_TRIG_SERIES_2_WIDTH 1 /* DCS_TRIG_SERIES_2 */
+#define WM8996_DCS_TRIG_SERIES_1 0x0200 /* DCS_TRIG_SERIES_1 */
+#define WM8996_DCS_TRIG_SERIES_1_MASK 0x0200 /* DCS_TRIG_SERIES_1 */
+#define WM8996_DCS_TRIG_SERIES_1_SHIFT 9 /* DCS_TRIG_SERIES_1 */
+#define WM8996_DCS_TRIG_SERIES_1_WIDTH 1 /* DCS_TRIG_SERIES_1 */
+#define WM8996_DCS_TRIG_SERIES_0 0x0100 /* DCS_TRIG_SERIES_0 */
+#define WM8996_DCS_TRIG_SERIES_0_MASK 0x0100 /* DCS_TRIG_SERIES_0 */
+#define WM8996_DCS_TRIG_SERIES_0_SHIFT 8 /* DCS_TRIG_SERIES_0 */
+#define WM8996_DCS_TRIG_SERIES_0_WIDTH 1 /* DCS_TRIG_SERIES_0 */
+#define WM8996_DCS_TRIG_STARTUP_3 0x0080 /* DCS_TRIG_STARTUP_3 */
+#define WM8996_DCS_TRIG_STARTUP_3_MASK 0x0080 /* DCS_TRIG_STARTUP_3 */
+#define WM8996_DCS_TRIG_STARTUP_3_SHIFT 7 /* DCS_TRIG_STARTUP_3 */
+#define WM8996_DCS_TRIG_STARTUP_3_WIDTH 1 /* DCS_TRIG_STARTUP_3 */
+#define WM8996_DCS_TRIG_STARTUP_2 0x0040 /* DCS_TRIG_STARTUP_2 */
+#define WM8996_DCS_TRIG_STARTUP_2_MASK 0x0040 /* DCS_TRIG_STARTUP_2 */
+#define WM8996_DCS_TRIG_STARTUP_2_SHIFT 6 /* DCS_TRIG_STARTUP_2 */
+#define WM8996_DCS_TRIG_STARTUP_2_WIDTH 1 /* DCS_TRIG_STARTUP_2 */
+#define WM8996_DCS_TRIG_STARTUP_1 0x0020 /* DCS_TRIG_STARTUP_1 */
+#define WM8996_DCS_TRIG_STARTUP_1_MASK 0x0020 /* DCS_TRIG_STARTUP_1 */
+#define WM8996_DCS_TRIG_STARTUP_1_SHIFT 5 /* DCS_TRIG_STARTUP_1 */
+#define WM8996_DCS_TRIG_STARTUP_1_WIDTH 1 /* DCS_TRIG_STARTUP_1 */
+#define WM8996_DCS_TRIG_STARTUP_0 0x0010 /* DCS_TRIG_STARTUP_0 */
+#define WM8996_DCS_TRIG_STARTUP_0_MASK 0x0010 /* DCS_TRIG_STARTUP_0 */
+#define WM8996_DCS_TRIG_STARTUP_0_SHIFT 4 /* DCS_TRIG_STARTUP_0 */
+#define WM8996_DCS_TRIG_STARTUP_0_WIDTH 1 /* DCS_TRIG_STARTUP_0 */
+#define WM8996_DCS_TRIG_DAC_WR_3 0x0008 /* DCS_TRIG_DAC_WR_3 */
+#define WM8996_DCS_TRIG_DAC_WR_3_MASK 0x0008 /* DCS_TRIG_DAC_WR_3 */
+#define WM8996_DCS_TRIG_DAC_WR_3_SHIFT 3 /* DCS_TRIG_DAC_WR_3 */
+#define WM8996_DCS_TRIG_DAC_WR_3_WIDTH 1 /* DCS_TRIG_DAC_WR_3 */
+#define WM8996_DCS_TRIG_DAC_WR_2 0x0004 /* DCS_TRIG_DAC_WR_2 */
+#define WM8996_DCS_TRIG_DAC_WR_2_MASK 0x0004 /* DCS_TRIG_DAC_WR_2 */
+#define WM8996_DCS_TRIG_DAC_WR_2_SHIFT 2 /* DCS_TRIG_DAC_WR_2 */
+#define WM8996_DCS_TRIG_DAC_WR_2_WIDTH 1 /* DCS_TRIG_DAC_WR_2 */
+#define WM8996_DCS_TRIG_DAC_WR_1 0x0002 /* DCS_TRIG_DAC_WR_1 */
+#define WM8996_DCS_TRIG_DAC_WR_1_MASK 0x0002 /* DCS_TRIG_DAC_WR_1 */
+#define WM8996_DCS_TRIG_DAC_WR_1_SHIFT 1 /* DCS_TRIG_DAC_WR_1 */
+#define WM8996_DCS_TRIG_DAC_WR_1_WIDTH 1 /* DCS_TRIG_DAC_WR_1 */
+#define WM8996_DCS_TRIG_DAC_WR_0 0x0001 /* DCS_TRIG_DAC_WR_0 */
+#define WM8996_DCS_TRIG_DAC_WR_0_MASK 0x0001 /* DCS_TRIG_DAC_WR_0 */
+#define WM8996_DCS_TRIG_DAC_WR_0_SHIFT 0 /* DCS_TRIG_DAC_WR_0 */
+#define WM8996_DCS_TRIG_DAC_WR_0_WIDTH 1 /* DCS_TRIG_DAC_WR_0 */
+
+/*
+ * R82 (0x52) - DC Servo (3)
+ */
+#define WM8996_DCS_TIMER_PERIOD_23_MASK 0x0F00 /* DCS_TIMER_PERIOD_23 - [11:8] */
+#define WM8996_DCS_TIMER_PERIOD_23_SHIFT 8 /* DCS_TIMER_PERIOD_23 - [11:8] */
+#define WM8996_DCS_TIMER_PERIOD_23_WIDTH 4 /* DCS_TIMER_PERIOD_23 - [11:8] */
+#define WM8996_DCS_TIMER_PERIOD_01_MASK 0x000F /* DCS_TIMER_PERIOD_01 - [3:0] */
+#define WM8996_DCS_TIMER_PERIOD_01_SHIFT 0 /* DCS_TIMER_PERIOD_01 - [3:0] */
+#define WM8996_DCS_TIMER_PERIOD_01_WIDTH 4 /* DCS_TIMER_PERIOD_01 - [3:0] */
+
+/*
+ * R84 (0x54) - DC Servo (5)
+ */
+#define WM8996_DCS_SERIES_NO_23_MASK 0x7F00 /* DCS_SERIES_NO_23 - [14:8] */
+#define WM8996_DCS_SERIES_NO_23_SHIFT 8 /* DCS_SERIES_NO_23 - [14:8] */
+#define WM8996_DCS_SERIES_NO_23_WIDTH 7 /* DCS_SERIES_NO_23 - [14:8] */
+#define WM8996_DCS_SERIES_NO_01_MASK 0x007F /* DCS_SERIES_NO_01 - [6:0] */
+#define WM8996_DCS_SERIES_NO_01_SHIFT 0 /* DCS_SERIES_NO_01 - [6:0] */
+#define WM8996_DCS_SERIES_NO_01_WIDTH 7 /* DCS_SERIES_NO_01 - [6:0] */
+
+/*
+ * R85 (0x55) - DC Servo (6)
+ */
+#define WM8996_DCS_DAC_WR_VAL_3_MASK 0xFF00 /* DCS_DAC_WR_VAL_3 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_3_SHIFT 8 /* DCS_DAC_WR_VAL_3 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_3_WIDTH 8 /* DCS_DAC_WR_VAL_3 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_2_MASK 0x00FF /* DCS_DAC_WR_VAL_2 - [7:0] */
+#define WM8996_DCS_DAC_WR_VAL_2_SHIFT 0 /* DCS_DAC_WR_VAL_2 - [7:0] */
+#define WM8996_DCS_DAC_WR_VAL_2_WIDTH 8 /* DCS_DAC_WR_VAL_2 - [7:0] */
+
+/*
+ * R86 (0x56) - DC Servo (7)
+ */
+#define WM8996_DCS_DAC_WR_VAL_1_MASK 0xFF00 /* DCS_DAC_WR_VAL_1 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_1_SHIFT 8 /* DCS_DAC_WR_VAL_1 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_1_WIDTH 8 /* DCS_DAC_WR_VAL_1 - [15:8] */
+#define WM8996_DCS_DAC_WR_VAL_0_MASK 0x00FF /* DCS_DAC_WR_VAL_0 - [7:0] */
+#define WM8996_DCS_DAC_WR_VAL_0_SHIFT 0 /* DCS_DAC_WR_VAL_0 - [7:0] */
+#define WM8996_DCS_DAC_WR_VAL_0_WIDTH 8 /* DCS_DAC_WR_VAL_0 - [7:0] */
+
+/*
+ * R87 (0x57) - DC Servo Readback 0
+ */
+#define WM8996_DCS_CAL_COMPLETE_MASK 0x0F00 /* DCS_CAL_COMPLETE - [11:8] */
+#define WM8996_DCS_CAL_COMPLETE_SHIFT 8 /* DCS_CAL_COMPLETE - [11:8] */
+#define WM8996_DCS_CAL_COMPLETE_WIDTH 4 /* DCS_CAL_COMPLETE - [11:8] */
+#define WM8996_DCS_DAC_WR_COMPLETE_MASK 0x00F0 /* DCS_DAC_WR_COMPLETE - [7:4] */
+#define WM8996_DCS_DAC_WR_COMPLETE_SHIFT 4 /* DCS_DAC_WR_COMPLETE - [7:4] */
+#define WM8996_DCS_DAC_WR_COMPLETE_WIDTH 4 /* DCS_DAC_WR_COMPLETE - [7:4] */
+#define WM8996_DCS_STARTUP_COMPLETE_MASK 0x000F /* DCS_STARTUP_COMPLETE - [3:0] */
+#define WM8996_DCS_STARTUP_COMPLETE_SHIFT 0 /* DCS_STARTUP_COMPLETE - [3:0] */
+#define WM8996_DCS_STARTUP_COMPLETE_WIDTH 4 /* DCS_STARTUP_COMPLETE - [3:0] */
+
+/*
+ * R96 (0x60) - Analogue HP (1)
+ */
+#define WM8996_HPOUT1L_RMV_SHORT 0x0080 /* HPOUT1L_RMV_SHORT */
+#define WM8996_HPOUT1L_RMV_SHORT_MASK 0x0080 /* HPOUT1L_RMV_SHORT */
+#define WM8996_HPOUT1L_RMV_SHORT_SHIFT 7 /* HPOUT1L_RMV_SHORT */
+#define WM8996_HPOUT1L_RMV_SHORT_WIDTH 1 /* HPOUT1L_RMV_SHORT */
+#define WM8996_HPOUT1L_OUTP 0x0040 /* HPOUT1L_OUTP */
+#define WM8996_HPOUT1L_OUTP_MASK 0x0040 /* HPOUT1L_OUTP */
+#define WM8996_HPOUT1L_OUTP_SHIFT 6 /* HPOUT1L_OUTP */
+#define WM8996_HPOUT1L_OUTP_WIDTH 1 /* HPOUT1L_OUTP */
+#define WM8996_HPOUT1L_DLY 0x0020 /* HPOUT1L_DLY */
+#define WM8996_HPOUT1L_DLY_MASK 0x0020 /* HPOUT1L_DLY */
+#define WM8996_HPOUT1L_DLY_SHIFT 5 /* HPOUT1L_DLY */
+#define WM8996_HPOUT1L_DLY_WIDTH 1 /* HPOUT1L_DLY */
+#define WM8996_HPOUT1R_RMV_SHORT 0x0008 /* HPOUT1R_RMV_SHORT */
+#define WM8996_HPOUT1R_RMV_SHORT_MASK 0x0008 /* HPOUT1R_RMV_SHORT */
+#define WM8996_HPOUT1R_RMV_SHORT_SHIFT 3 /* HPOUT1R_RMV_SHORT */
+#define WM8996_HPOUT1R_RMV_SHORT_WIDTH 1 /* HPOUT1R_RMV_SHORT */
+#define WM8996_HPOUT1R_OUTP 0x0004 /* HPOUT1R_OUTP */
+#define WM8996_HPOUT1R_OUTP_MASK 0x0004 /* HPOUT1R_OUTP */
+#define WM8996_HPOUT1R_OUTP_SHIFT 2 /* HPOUT1R_OUTP */
+#define WM8996_HPOUT1R_OUTP_WIDTH 1 /* HPOUT1R_OUTP */
+#define WM8996_HPOUT1R_DLY 0x0002 /* HPOUT1R_DLY */
+#define WM8996_HPOUT1R_DLY_MASK 0x0002 /* HPOUT1R_DLY */
+#define WM8996_HPOUT1R_DLY_SHIFT 1 /* HPOUT1R_DLY */
+#define WM8996_HPOUT1R_DLY_WIDTH 1 /* HPOUT1R_DLY */
+
+/*
+ * R97 (0x61) - Analogue HP (2)
+ */
+#define WM8996_HPOUT2L_RMV_SHORT 0x0080 /* HPOUT2L_RMV_SHORT */
+#define WM8996_HPOUT2L_RMV_SHORT_MASK 0x0080 /* HPOUT2L_RMV_SHORT */
+#define WM8996_HPOUT2L_RMV_SHORT_SHIFT 7 /* HPOUT2L_RMV_SHORT */
+#define WM8996_HPOUT2L_RMV_SHORT_WIDTH 1 /* HPOUT2L_RMV_SHORT */
+#define WM8996_HPOUT2L_OUTP 0x0040 /* HPOUT2L_OUTP */
+#define WM8996_HPOUT2L_OUTP_MASK 0x0040 /* HPOUT2L_OUTP */
+#define WM8996_HPOUT2L_OUTP_SHIFT 6 /* HPOUT2L_OUTP */
+#define WM8996_HPOUT2L_OUTP_WIDTH 1 /* HPOUT2L_OUTP */
+#define WM8996_HPOUT2L_DLY 0x0020 /* HPOUT2L_DLY */
+#define WM8996_HPOUT2L_DLY_MASK 0x0020 /* HPOUT2L_DLY */
+#define WM8996_HPOUT2L_DLY_SHIFT 5 /* HPOUT2L_DLY */
+#define WM8996_HPOUT2L_DLY_WIDTH 1 /* HPOUT2L_DLY */
+#define WM8996_HPOUT2R_RMV_SHORT 0x0008 /* HPOUT2R_RMV_SHORT */
+#define WM8996_HPOUT2R_RMV_SHORT_MASK 0x0008 /* HPOUT2R_RMV_SHORT */
+#define WM8996_HPOUT2R_RMV_SHORT_SHIFT 3 /* HPOUT2R_RMV_SHORT */
+#define WM8996_HPOUT2R_RMV_SHORT_WIDTH 1 /* HPOUT2R_RMV_SHORT */
+#define WM8996_HPOUT2R_OUTP 0x0004 /* HPOUT2R_OUTP */
+#define WM8996_HPOUT2R_OUTP_MASK 0x0004 /* HPOUT2R_OUTP */
+#define WM8996_HPOUT2R_OUTP_SHIFT 2 /* HPOUT2R_OUTP */
+#define WM8996_HPOUT2R_OUTP_WIDTH 1 /* HPOUT2R_OUTP */
+#define WM8996_HPOUT2R_DLY 0x0002 /* HPOUT2R_DLY */
+#define WM8996_HPOUT2R_DLY_MASK 0x0002 /* HPOUT2R_DLY */
+#define WM8996_HPOUT2R_DLY_SHIFT 1 /* HPOUT2R_DLY */
+#define WM8996_HPOUT2R_DLY_WIDTH 1 /* HPOUT2R_DLY */
+
+/*
+ * R256 (0x100) - Chip Revision
+ */
+#define WM8996_CHIP_REV_MASK 0x000F /* CHIP_REV - [3:0] */
+#define WM8996_CHIP_REV_SHIFT 0 /* CHIP_REV - [3:0] */
+#define WM8996_CHIP_REV_WIDTH 4 /* CHIP_REV - [3:0] */
+
+/*
+ * R257 (0x101) - Control Interface (1)
+ */
+#define WM8996_AUTO_INC 0x0004 /* AUTO_INC */
+#define WM8996_AUTO_INC_MASK 0x0004 /* AUTO_INC */
+#define WM8996_AUTO_INC_SHIFT 2 /* AUTO_INC */
+#define WM8996_AUTO_INC_WIDTH 1 /* AUTO_INC */
+
+/*
+ * R272 (0x110) - Write Sequencer Ctrl (1)
+ */
+#define WM8996_WSEQ_ENA 0x8000 /* WSEQ_ENA */
+#define WM8996_WSEQ_ENA_MASK 0x8000 /* WSEQ_ENA */
+#define WM8996_WSEQ_ENA_SHIFT 15 /* WSEQ_ENA */
+#define WM8996_WSEQ_ENA_WIDTH 1 /* WSEQ_ENA */
+#define WM8996_WSEQ_ABORT 0x0200 /* WSEQ_ABORT */
+#define WM8996_WSEQ_ABORT_MASK 0x0200 /* WSEQ_ABORT */
+#define WM8996_WSEQ_ABORT_SHIFT 9 /* WSEQ_ABORT */
+#define WM8996_WSEQ_ABORT_WIDTH 1 /* WSEQ_ABORT */
+#define WM8996_WSEQ_START 0x0100 /* WSEQ_START */
+#define WM8996_WSEQ_START_MASK 0x0100 /* WSEQ_START */
+#define WM8996_WSEQ_START_SHIFT 8 /* WSEQ_START */
+#define WM8996_WSEQ_START_WIDTH 1 /* WSEQ_START */
+#define WM8996_WSEQ_START_INDEX_MASK 0x007F /* WSEQ_START_INDEX - [6:0] */
+#define WM8996_WSEQ_START_INDEX_SHIFT 0 /* WSEQ_START_INDEX - [6:0] */
+#define WM8996_WSEQ_START_INDEX_WIDTH 7 /* WSEQ_START_INDEX - [6:0] */
+
+/*
+ * R273 (0x111) - Write Sequencer Ctrl (2)
+ */
+#define WM8996_WSEQ_BUSY 0x0100 /* WSEQ_BUSY */
+#define WM8996_WSEQ_BUSY_MASK 0x0100 /* WSEQ_BUSY */
+#define WM8996_WSEQ_BUSY_SHIFT 8 /* WSEQ_BUSY */
+#define WM8996_WSEQ_BUSY_WIDTH 1 /* WSEQ_BUSY */
+#define WM8996_WSEQ_CURRENT_INDEX_MASK 0x007F /* WSEQ_CURRENT_INDEX - [6:0] */
+#define WM8996_WSEQ_CURRENT_INDEX_SHIFT 0 /* WSEQ_CURRENT_INDEX - [6:0] */
+#define WM8996_WSEQ_CURRENT_INDEX_WIDTH 7 /* WSEQ_CURRENT_INDEX - [6:0] */
+
+/*
+ * R512 (0x200) - AIF Clocking (1)
+ */
+#define WM8996_SYSCLK_SRC_MASK 0x0018 /* SYSCLK_SRC - [4:3] */
+#define WM8996_SYSCLK_SRC_SHIFT 3 /* SYSCLK_SRC - [4:3] */
+#define WM8996_SYSCLK_SRC_WIDTH 2 /* SYSCLK_SRC - [4:3] */
+#define WM8996_SYSCLK_INV 0x0004 /* SYSCLK_INV */
+#define WM8996_SYSCLK_INV_MASK 0x0004 /* SYSCLK_INV */
+#define WM8996_SYSCLK_INV_SHIFT 2 /* SYSCLK_INV */
+#define WM8996_SYSCLK_INV_WIDTH 1 /* SYSCLK_INV */
+#define WM8996_SYSCLK_DIV 0x0002 /* SYSCLK_DIV */
+#define WM8996_SYSCLK_DIV_MASK 0x0002 /* SYSCLK_DIV */
+#define WM8996_SYSCLK_DIV_SHIFT 1 /* SYSCLK_DIV */
+#define WM8996_SYSCLK_DIV_WIDTH 1 /* SYSCLK_DIV */
+#define WM8996_SYSCLK_ENA 0x0001 /* SYSCLK_ENA */
+#define WM8996_SYSCLK_ENA_MASK 0x0001 /* SYSCLK_ENA */
+#define WM8996_SYSCLK_ENA_SHIFT 0 /* SYSCLK_ENA */
+#define WM8996_SYSCLK_ENA_WIDTH 1 /* SYSCLK_ENA */
+
+/*
+ * R513 (0x201) - AIF Clocking (2)
+ */
+#define WM8996_DSP2_DIV_MASK 0x0018 /* DSP2_DIV - [4:3] */
+#define WM8996_DSP2_DIV_SHIFT 3 /* DSP2_DIV - [4:3] */
+#define WM8996_DSP2_DIV_WIDTH 2 /* DSP2_DIV - [4:3] */
+#define WM8996_DSP1_DIV_MASK 0x0003 /* DSP1_DIV - [1:0] */
+#define WM8996_DSP1_DIV_SHIFT 0 /* DSP1_DIV - [1:0] */
+#define WM8996_DSP1_DIV_WIDTH 2 /* DSP1_DIV - [1:0] */
+
+/*
+ * R520 (0x208) - Clocking (1)
+ */
+#define WM8996_LFCLK_ENA 0x0020 /* LFCLK_ENA */
+#define WM8996_LFCLK_ENA_MASK 0x0020 /* LFCLK_ENA */
+#define WM8996_LFCLK_ENA_SHIFT 5 /* LFCLK_ENA */
+#define WM8996_LFCLK_ENA_WIDTH 1 /* LFCLK_ENA */
+#define WM8996_TOCLK_ENA 0x0010 /* TOCLK_ENA */
+#define WM8996_TOCLK_ENA_MASK 0x0010 /* TOCLK_ENA */
+#define WM8996_TOCLK_ENA_SHIFT 4 /* TOCLK_ENA */
+#define WM8996_TOCLK_ENA_WIDTH 1 /* TOCLK_ENA */
+#define WM8996_AIFCLK_ENA 0x0004 /* AIFCLK_ENA */
+#define WM8996_AIFCLK_ENA_MASK 0x0004 /* AIFCLK_ENA */
+#define WM8996_AIFCLK_ENA_SHIFT 2 /* AIFCLK_ENA */
+#define WM8996_AIFCLK_ENA_WIDTH 1 /* AIFCLK_ENA */
+#define WM8996_SYSDSPCLK_ENA 0x0002 /* SYSDSPCLK_ENA */
+#define WM8996_SYSDSPCLK_ENA_MASK 0x0002 /* SYSDSPCLK_ENA */
+#define WM8996_SYSDSPCLK_ENA_SHIFT 1 /* SYSDSPCLK_ENA */
+#define WM8996_SYSDSPCLK_ENA_WIDTH 1 /* SYSDSPCLK_ENA */
+
+/*
+ * R521 (0x209) - Clocking (2)
+ */
+#define WM8996_TOCLK_DIV_MASK 0x0700 /* TOCLK_DIV - [10:8] */
+#define WM8996_TOCLK_DIV_SHIFT 8 /* TOCLK_DIV - [10:8] */
+#define WM8996_TOCLK_DIV_WIDTH 3 /* TOCLK_DIV - [10:8] */
+#define WM8996_DBCLK_DIV_MASK 0x00F0 /* DBCLK_DIV - [7:4] */
+#define WM8996_DBCLK_DIV_SHIFT 4 /* DBCLK_DIV - [7:4] */
+#define WM8996_DBCLK_DIV_WIDTH 4 /* DBCLK_DIV - [7:4] */
+#define WM8996_OPCLK_DIV_MASK 0x0007 /* OPCLK_DIV - [2:0] */
+#define WM8996_OPCLK_DIV_SHIFT 0 /* OPCLK_DIV - [2:0] */
+#define WM8996_OPCLK_DIV_WIDTH 3 /* OPCLK_DIV - [2:0] */
+
+/*
+ * R528 (0x210) - AIF Rate
+ */
+#define WM8996_SYSCLK_RATE 0x0001 /* SYSCLK_RATE */
+#define WM8996_SYSCLK_RATE_MASK 0x0001 /* SYSCLK_RATE */
+#define WM8996_SYSCLK_RATE_SHIFT 0 /* SYSCLK_RATE */
+#define WM8996_SYSCLK_RATE_WIDTH 1 /* SYSCLK_RATE */
+
+/*
+ * R544 (0x220) - FLL Control (1)
+ */
+#define WM8996_FLL_OSC_ENA 0x0002 /* FLL_OSC_ENA */
+#define WM8996_FLL_OSC_ENA_MASK 0x0002 /* FLL_OSC_ENA */
+#define WM8996_FLL_OSC_ENA_SHIFT 1 /* FLL_OSC_ENA */
+#define WM8996_FLL_OSC_ENA_WIDTH 1 /* FLL_OSC_ENA */
+#define WM8996_FLL_ENA 0x0001 /* FLL_ENA */
+#define WM8996_FLL_ENA_MASK 0x0001 /* FLL_ENA */
+#define WM8996_FLL_ENA_SHIFT 0 /* FLL_ENA */
+#define WM8996_FLL_ENA_WIDTH 1 /* FLL_ENA */
+
+/*
+ * R545 (0x221) - FLL Control (2)
+ */
+#define WM8996_FLL_OUTDIV_MASK 0x3F00 /* FLL_OUTDIV - [13:8] */
+#define WM8996_FLL_OUTDIV_SHIFT 8 /* FLL_OUTDIV - [13:8] */
+#define WM8996_FLL_OUTDIV_WIDTH 6 /* FLL_OUTDIV - [13:8] */
+#define WM8996_FLL_FRATIO_MASK 0x0007 /* FLL_FRATIO - [2:0] */
+#define WM8996_FLL_FRATIO_SHIFT 0 /* FLL_FRATIO - [2:0] */
+#define WM8996_FLL_FRATIO_WIDTH 3 /* FLL_FRATIO - [2:0] */
+
+/*
+ * R546 (0x222) - FLL Control (3)
+ */
+#define WM8996_FLL_THETA_MASK 0xFFFF /* FLL_THETA - [15:0] */
+#define WM8996_FLL_THETA_SHIFT 0 /* FLL_THETA - [15:0] */
+#define WM8996_FLL_THETA_WIDTH 16 /* FLL_THETA - [15:0] */
+
+/*
+ * R547 (0x223) - FLL Control (4)
+ */
+#define WM8996_FLL_N_MASK 0x7FE0 /* FLL_N - [14:5] */
+#define WM8996_FLL_N_SHIFT 5 /* FLL_N - [14:5] */
+#define WM8996_FLL_N_WIDTH 10 /* FLL_N - [14:5] */
+#define WM8996_FLL_LOOP_GAIN_MASK 0x000F /* FLL_LOOP_GAIN - [3:0] */
+#define WM8996_FLL_LOOP_GAIN_SHIFT 0 /* FLL_LOOP_GAIN - [3:0] */
+#define WM8996_FLL_LOOP_GAIN_WIDTH 4 /* FLL_LOOP_GAIN - [3:0] */
+
+/*
+ * R548 (0x224) - FLL Control (5)
+ */
+#define WM8996_FLL_FRC_NCO_VAL_MASK 0x1F80 /* FLL_FRC_NCO_VAL - [12:7] */
+#define WM8996_FLL_FRC_NCO_VAL_SHIFT 7 /* FLL_FRC_NCO_VAL - [12:7] */
+#define WM8996_FLL_FRC_NCO_VAL_WIDTH 6 /* FLL_FRC_NCO_VAL - [12:7] */
+#define WM8996_FLL_FRC_NCO 0x0040 /* FLL_FRC_NCO */
+#define WM8996_FLL_FRC_NCO_MASK 0x0040 /* FLL_FRC_NCO */
+#define WM8996_FLL_FRC_NCO_SHIFT 6 /* FLL_FRC_NCO */
+#define WM8996_FLL_FRC_NCO_WIDTH 1 /* FLL_FRC_NCO */
+#define WM8996_FLL_REFCLK_DIV_MASK 0x0018 /* FLL_REFCLK_DIV - [4:3] */
+#define WM8996_FLL_REFCLK_DIV_SHIFT 3 /* FLL_REFCLK_DIV - [4:3] */
+#define WM8996_FLL_REFCLK_DIV_WIDTH 2 /* FLL_REFCLK_DIV - [4:3] */
+#define WM8996_FLL_REF_FREQ 0x0004 /* FLL_REF_FREQ */
+#define WM8996_FLL_REF_FREQ_MASK 0x0004 /* FLL_REF_FREQ */
+#define WM8996_FLL_REF_FREQ_SHIFT 2 /* FLL_REF_FREQ */
+#define WM8996_FLL_REF_FREQ_WIDTH 1 /* FLL_REF_FREQ */
+#define WM8996_FLL_REFCLK_SRC_MASK 0x0003 /* FLL_REFCLK_SRC - [1:0] */
+#define WM8996_FLL_REFCLK_SRC_SHIFT 0 /* FLL_REFCLK_SRC - [1:0] */
+#define WM8996_FLL_REFCLK_SRC_WIDTH 2 /* FLL_REFCLK_SRC - [1:0] */
+
+/*
+ * R549 (0x225) - FLL Control (6)
+ */
+#define WM8996_FLL_REFCLK_SRC_STS_MASK 0x000C /* FLL_REFCLK_SRC_STS - [3:2] */
+#define WM8996_FLL_REFCLK_SRC_STS_SHIFT 2 /* FLL_REFCLK_SRC_STS - [3:2] */
+#define WM8996_FLL_REFCLK_SRC_STS_WIDTH 2 /* FLL_REFCLK_SRC_STS - [3:2] */
+#define WM8996_FLL_SWITCH_CLK 0x0001 /* FLL_SWITCH_CLK */
+#define WM8996_FLL_SWITCH_CLK_MASK 0x0001 /* FLL_SWITCH_CLK */
+#define WM8996_FLL_SWITCH_CLK_SHIFT 0 /* FLL_SWITCH_CLK */
+#define WM8996_FLL_SWITCH_CLK_WIDTH 1 /* FLL_SWITCH_CLK */
+
+/*
+ * R550 (0x226) - FLL EFS 1
+ */
+#define WM8996_FLL_LAMBDA_MASK 0xFFFF /* FLL_LAMBDA - [15:0] */
+#define WM8996_FLL_LAMBDA_SHIFT 0 /* FLL_LAMBDA - [15:0] */
+#define WM8996_FLL_LAMBDA_WIDTH 16 /* FLL_LAMBDA - [15:0] */
+
+/*
+ * R551 (0x227) - FLL EFS 2
+ */
+#define WM8996_FLL_LFSR_SEL_MASK 0x0006 /* FLL_LFSR_SEL - [2:1] */
+#define WM8996_FLL_LFSR_SEL_SHIFT 1 /* FLL_LFSR_SEL - [2:1] */
+#define WM8996_FLL_LFSR_SEL_WIDTH 2 /* FLL_LFSR_SEL - [2:1] */
+#define WM8996_FLL_EFS_ENA 0x0001 /* FLL_EFS_ENA */
+#define WM8996_FLL_EFS_ENA_MASK 0x0001 /* FLL_EFS_ENA */
+#define WM8996_FLL_EFS_ENA_SHIFT 0 /* FLL_EFS_ENA */
+#define WM8996_FLL_EFS_ENA_WIDTH 1 /* FLL_EFS_ENA */
+
+/*
+ * R768 (0x300) - AIF1 Control
+ */
+#define WM8996_AIF1_TRI 0x0004 /* AIF1_TRI */
+#define WM8996_AIF1_TRI_MASK 0x0004 /* AIF1_TRI */
+#define WM8996_AIF1_TRI_SHIFT 2 /* AIF1_TRI */
+#define WM8996_AIF1_TRI_WIDTH 1 /* AIF1_TRI */
+#define WM8996_AIF1_FMT_MASK 0x0003 /* AIF1_FMT - [1:0] */
+#define WM8996_AIF1_FMT_SHIFT 0 /* AIF1_FMT - [1:0] */
+#define WM8996_AIF1_FMT_WIDTH 2 /* AIF1_FMT - [1:0] */
+
+/*
+ * R769 (0x301) - AIF1 BCLK
+ */
+#define WM8996_AIF1_BCLK_INV 0x0400 /* AIF1_BCLK_INV */
+#define WM8996_AIF1_BCLK_INV_MASK 0x0400 /* AIF1_BCLK_INV */
+#define WM8996_AIF1_BCLK_INV_SHIFT 10 /* AIF1_BCLK_INV */
+#define WM8996_AIF1_BCLK_INV_WIDTH 1 /* AIF1_BCLK_INV */
+#define WM8996_AIF1_BCLK_FRC 0x0200 /* AIF1_BCLK_FRC */
+#define WM8996_AIF1_BCLK_FRC_MASK 0x0200 /* AIF1_BCLK_FRC */
+#define WM8996_AIF1_BCLK_FRC_SHIFT 9 /* AIF1_BCLK_FRC */
+#define WM8996_AIF1_BCLK_FRC_WIDTH 1 /* AIF1_BCLK_FRC */
+#define WM8996_AIF1_BCLK_MSTR 0x0100 /* AIF1_BCLK_MSTR */
+#define WM8996_AIF1_BCLK_MSTR_MASK 0x0100 /* AIF1_BCLK_MSTR */
+#define WM8996_AIF1_BCLK_MSTR_SHIFT 8 /* AIF1_BCLK_MSTR */
+#define WM8996_AIF1_BCLK_MSTR_WIDTH 1 /* AIF1_BCLK_MSTR */
+#define WM8996_AIF1_BCLK_DIV_MASK 0x000F /* AIF1_BCLK_DIV - [3:0] */
+#define WM8996_AIF1_BCLK_DIV_SHIFT 0 /* AIF1_BCLK_DIV - [3:0] */
+#define WM8996_AIF1_BCLK_DIV_WIDTH 4 /* AIF1_BCLK_DIV - [3:0] */
+
+/*
+ * R770 (0x302) - AIF1 TX LRCLK(1)
+ */
+#define WM8996_AIF1TX_RATE_MASK 0x07FF /* AIF1TX_RATE - [10:0] */
+#define WM8996_AIF1TX_RATE_SHIFT 0 /* AIF1TX_RATE - [10:0] */
+#define WM8996_AIF1TX_RATE_WIDTH 11 /* AIF1TX_RATE - [10:0] */
+
+/*
+ * R771 (0x303) - AIF1 TX LRCLK(2)
+ */
+#define WM8996_AIF1TX_LRCLK_MODE 0x0008 /* AIF1TX_LRCLK_MODE */
+#define WM8996_AIF1TX_LRCLK_MODE_MASK 0x0008 /* AIF1TX_LRCLK_MODE */
+#define WM8996_AIF1TX_LRCLK_MODE_SHIFT 3 /* AIF1TX_LRCLK_MODE */
+#define WM8996_AIF1TX_LRCLK_MODE_WIDTH 1 /* AIF1TX_LRCLK_MODE */
+#define WM8996_AIF1TX_LRCLK_INV 0x0004 /* AIF1TX_LRCLK_INV */
+#define WM8996_AIF1TX_LRCLK_INV_MASK 0x0004 /* AIF1TX_LRCLK_INV */
+#define WM8996_AIF1TX_LRCLK_INV_SHIFT 2 /* AIF1TX_LRCLK_INV */
+#define WM8996_AIF1TX_LRCLK_INV_WIDTH 1 /* AIF1TX_LRCLK_INV */
+#define WM8996_AIF1TX_LRCLK_FRC 0x0002 /* AIF1TX_LRCLK_FRC */
+#define WM8996_AIF1TX_LRCLK_FRC_MASK 0x0002 /* AIF1TX_LRCLK_FRC */
+#define WM8996_AIF1TX_LRCLK_FRC_SHIFT 1 /* AIF1TX_LRCLK_FRC */
+#define WM8996_AIF1TX_LRCLK_FRC_WIDTH 1 /* AIF1TX_LRCLK_FRC */
+#define WM8996_AIF1TX_LRCLK_MSTR 0x0001 /* AIF1TX_LRCLK_MSTR */
+#define WM8996_AIF1TX_LRCLK_MSTR_MASK 0x0001 /* AIF1TX_LRCLK_MSTR */
+#define WM8996_AIF1TX_LRCLK_MSTR_SHIFT 0 /* AIF1TX_LRCLK_MSTR */
+#define WM8996_AIF1TX_LRCLK_MSTR_WIDTH 1 /* AIF1TX_LRCLK_MSTR */
+
+/*
+ * R772 (0x304) - AIF1 RX LRCLK(1)
+ */
+#define WM8996_AIF1RX_RATE_MASK 0x07FF /* AIF1RX_RATE - [10:0] */
+#define WM8996_AIF1RX_RATE_SHIFT 0 /* AIF1RX_RATE - [10:0] */
+#define WM8996_AIF1RX_RATE_WIDTH 11 /* AIF1RX_RATE - [10:0] */
+
+/*
+ * R773 (0x305) - AIF1 RX LRCLK(2)
+ */
+#define WM8996_AIF1RX_LRCLK_INV 0x0004 /* AIF1RX_LRCLK_INV */
+#define WM8996_AIF1RX_LRCLK_INV_MASK 0x0004 /* AIF1RX_LRCLK_INV */
+#define WM8996_AIF1RX_LRCLK_INV_SHIFT 2 /* AIF1RX_LRCLK_INV */
+#define WM8996_AIF1RX_LRCLK_INV_WIDTH 1 /* AIF1RX_LRCLK_INV */
+#define WM8996_AIF1RX_LRCLK_FRC 0x0002 /* AIF1RX_LRCLK_FRC */
+#define WM8996_AIF1RX_LRCLK_FRC_MASK 0x0002 /* AIF1RX_LRCLK_FRC */
+#define WM8996_AIF1RX_LRCLK_FRC_SHIFT 1 /* AIF1RX_LRCLK_FRC */
+#define WM8996_AIF1RX_LRCLK_FRC_WIDTH 1 /* AIF1RX_LRCLK_FRC */
+#define WM8996_AIF1RX_LRCLK_MSTR 0x0001 /* AIF1RX_LRCLK_MSTR */
+#define WM8996_AIF1RX_LRCLK_MSTR_MASK 0x0001 /* AIF1RX_LRCLK_MSTR */
+#define WM8996_AIF1RX_LRCLK_MSTR_SHIFT 0 /* AIF1RX_LRCLK_MSTR */
+#define WM8996_AIF1RX_LRCLK_MSTR_WIDTH 1 /* AIF1RX_LRCLK_MSTR */
+
+/*
+ * R774 (0x306) - AIF1TX Data Configuration (1)
+ */
+#define WM8996_AIF1TX_WL_MASK 0xFF00 /* AIF1TX_WL - [15:8] */
+#define WM8996_AIF1TX_WL_SHIFT 8 /* AIF1TX_WL - [15:8] */
+#define WM8996_AIF1TX_WL_WIDTH 8 /* AIF1TX_WL - [15:8] */
+#define WM8996_AIF1TX_SLOT_LEN_MASK 0x00FF /* AIF1TX_SLOT_LEN - [7:0] */
+#define WM8996_AIF1TX_SLOT_LEN_SHIFT 0 /* AIF1TX_SLOT_LEN - [7:0] */
+#define WM8996_AIF1TX_SLOT_LEN_WIDTH 8 /* AIF1TX_SLOT_LEN - [7:0] */
+
+/*
+ * R775 (0x307) - AIF1TX Data Configuration (2)
+ */
+#define WM8996_AIF1TX_DAT_TRI 0x0001 /* AIF1TX_DAT_TRI */
+#define WM8996_AIF1TX_DAT_TRI_MASK 0x0001 /* AIF1TX_DAT_TRI */
+#define WM8996_AIF1TX_DAT_TRI_SHIFT 0 /* AIF1TX_DAT_TRI */
+#define WM8996_AIF1TX_DAT_TRI_WIDTH 1 /* AIF1TX_DAT_TRI */
+
+/*
+ * R776 (0x308) - AIF1RX Data Configuration
+ */
+#define WM8996_AIF1RX_WL_MASK 0xFF00 /* AIF1RX_WL - [15:8] */
+#define WM8996_AIF1RX_WL_SHIFT 8 /* AIF1RX_WL - [15:8] */
+#define WM8996_AIF1RX_WL_WIDTH 8 /* AIF1RX_WL - [15:8] */
+#define WM8996_AIF1RX_SLOT_LEN_MASK 0x00FF /* AIF1RX_SLOT_LEN - [7:0] */
+#define WM8996_AIF1RX_SLOT_LEN_SHIFT 0 /* AIF1RX_SLOT_LEN - [7:0] */
+#define WM8996_AIF1RX_SLOT_LEN_WIDTH 8 /* AIF1RX_SLOT_LEN - [7:0] */
+
+/*
+ * R777 (0x309) - AIF1TX Channel 0 Configuration
+ */
+#define WM8996_AIF1TX_CHAN0_DAT_INV 0x8000 /* AIF1TX_CHAN0_DAT_INV */
+#define WM8996_AIF1TX_CHAN0_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN0_DAT_INV */
+#define WM8996_AIF1TX_CHAN0_DAT_INV_SHIFT 15 /* AIF1TX_CHAN0_DAT_INV */
+#define WM8996_AIF1TX_CHAN0_DAT_INV_WIDTH 1 /* AIF1TX_CHAN0_DAT_INV */
+#define WM8996_AIF1TX_CHAN0_SPACING_MASK 0x7E00 /* AIF1TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN0_SPACING_SHIFT 9 /* AIF1TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN0_SPACING_WIDTH 6 /* AIF1TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN0_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN0_SLOTS_SHIFT 6 /* AIF1TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN0_SLOTS_WIDTH 3 /* AIF1TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN0_START_SLOT_MASK 0x003F /* AIF1TX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN0_START_SLOT_SHIFT 0 /* AIF1TX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN0_START_SLOT_WIDTH 6 /* AIF1TX_CHAN0_START_SLOT - [5:0] */
+
+/*
+ * R778 (0x30A) - AIF1TX Channel 1 Configuration
+ */
+#define WM8996_AIF1TX_CHAN1_DAT_INV 0x8000 /* AIF1TX_CHAN1_DAT_INV */
+#define WM8996_AIF1TX_CHAN1_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN1_DAT_INV */
+#define WM8996_AIF1TX_CHAN1_DAT_INV_SHIFT 15 /* AIF1TX_CHAN1_DAT_INV */
+#define WM8996_AIF1TX_CHAN1_DAT_INV_WIDTH 1 /* AIF1TX_CHAN1_DAT_INV */
+#define WM8996_AIF1TX_CHAN1_SPACING_MASK 0x7E00 /* AIF1TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN1_SPACING_SHIFT 9 /* AIF1TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN1_SPACING_WIDTH 6 /* AIF1TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN1_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN1_SLOTS_SHIFT 6 /* AIF1TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN1_SLOTS_WIDTH 3 /* AIF1TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN1_START_SLOT_MASK 0x003F /* AIF1TX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN1_START_SLOT_SHIFT 0 /* AIF1TX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN1_START_SLOT_WIDTH 6 /* AIF1TX_CHAN1_START_SLOT - [5:0] */
+
+/*
+ * R779 (0x30B) - AIF1TX Channel 2 Configuration
+ */
+#define WM8996_AIF1TX_CHAN2_DAT_INV 0x8000 /* AIF1TX_CHAN2_DAT_INV */
+#define WM8996_AIF1TX_CHAN2_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN2_DAT_INV */
+#define WM8996_AIF1TX_CHAN2_DAT_INV_SHIFT 15 /* AIF1TX_CHAN2_DAT_INV */
+#define WM8996_AIF1TX_CHAN2_DAT_INV_WIDTH 1 /* AIF1TX_CHAN2_DAT_INV */
+#define WM8996_AIF1TX_CHAN2_SPACING_MASK 0x7E00 /* AIF1TX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN2_SPACING_SHIFT 9 /* AIF1TX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN2_SPACING_WIDTH 6 /* AIF1TX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN2_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN2_SLOTS_SHIFT 6 /* AIF1TX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN2_SLOTS_WIDTH 3 /* AIF1TX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN2_START_SLOT_MASK 0x003F /* AIF1TX_CHAN2_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN2_START_SLOT_SHIFT 0 /* AIF1TX_CHAN2_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN2_START_SLOT_WIDTH 6 /* AIF1TX_CHAN2_START_SLOT - [5:0] */
+
+/*
+ * R780 (0x30C) - AIF1TX Channel 3 Configuration
+ */
+#define WM8996_AIF1TX_CHAN3_DAT_INV 0x8000 /* AIF1TX_CHAN3_DAT_INV */
+#define WM8996_AIF1TX_CHAN3_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN3_DAT_INV */
+#define WM8996_AIF1TX_CHAN3_DAT_INV_SHIFT 15 /* AIF1TX_CHAN3_DAT_INV */
+#define WM8996_AIF1TX_CHAN3_DAT_INV_WIDTH 1 /* AIF1TX_CHAN3_DAT_INV */
+#define WM8996_AIF1TX_CHAN3_SPACING_MASK 0x7E00 /* AIF1TX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN3_SPACING_SHIFT 9 /* AIF1TX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN3_SPACING_WIDTH 6 /* AIF1TX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN3_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN3_SLOTS_SHIFT 6 /* AIF1TX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN3_SLOTS_WIDTH 3 /* AIF1TX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN3_START_SLOT_MASK 0x003F /* AIF1TX_CHAN3_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN3_START_SLOT_SHIFT 0 /* AIF1TX_CHAN3_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN3_START_SLOT_WIDTH 6 /* AIF1TX_CHAN3_START_SLOT - [5:0] */
+
+/*
+ * R781 (0x30D) - AIF1TX Channel 4 Configuration
+ */
+#define WM8996_AIF1TX_CHAN4_DAT_INV 0x8000 /* AIF1TX_CHAN4_DAT_INV */
+#define WM8996_AIF1TX_CHAN4_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN4_DAT_INV */
+#define WM8996_AIF1TX_CHAN4_DAT_INV_SHIFT 15 /* AIF1TX_CHAN4_DAT_INV */
+#define WM8996_AIF1TX_CHAN4_DAT_INV_WIDTH 1 /* AIF1TX_CHAN4_DAT_INV */
+#define WM8996_AIF1TX_CHAN4_SPACING_MASK 0x7E00 /* AIF1TX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN4_SPACING_SHIFT 9 /* AIF1TX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN4_SPACING_WIDTH 6 /* AIF1TX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN4_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN4_SLOTS_SHIFT 6 /* AIF1TX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN4_SLOTS_WIDTH 3 /* AIF1TX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN4_START_SLOT_MASK 0x003F /* AIF1TX_CHAN4_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN4_START_SLOT_SHIFT 0 /* AIF1TX_CHAN4_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN4_START_SLOT_WIDTH 6 /* AIF1TX_CHAN4_START_SLOT - [5:0] */
+
+/*
+ * R782 (0x30E) - AIF1TX Channel 5 Configuration
+ */
+#define WM8996_AIF1TX_CHAN5_DAT_INV 0x8000 /* AIF1TX_CHAN5_DAT_INV */
+#define WM8996_AIF1TX_CHAN5_DAT_INV_MASK 0x8000 /* AIF1TX_CHAN5_DAT_INV */
+#define WM8996_AIF1TX_CHAN5_DAT_INV_SHIFT 15 /* AIF1TX_CHAN5_DAT_INV */
+#define WM8996_AIF1TX_CHAN5_DAT_INV_WIDTH 1 /* AIF1TX_CHAN5_DAT_INV */
+#define WM8996_AIF1TX_CHAN5_SPACING_MASK 0x7E00 /* AIF1TX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN5_SPACING_SHIFT 9 /* AIF1TX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN5_SPACING_WIDTH 6 /* AIF1TX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1TX_CHAN5_SLOTS_MASK 0x01C0 /* AIF1TX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN5_SLOTS_SHIFT 6 /* AIF1TX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN5_SLOTS_WIDTH 3 /* AIF1TX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1TX_CHAN5_START_SLOT_MASK 0x003F /* AIF1TX_CHAN5_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN5_START_SLOT_SHIFT 0 /* AIF1TX_CHAN5_START_SLOT - [5:0] */
+#define WM8996_AIF1TX_CHAN5_START_SLOT_WIDTH 6 /* AIF1TX_CHAN5_START_SLOT - [5:0] */
+
+/*
+ * R783 (0x30F) - AIF1RX Channel 0 Configuration
+ */
+#define WM8996_AIF1RX_CHAN0_DAT_INV 0x8000 /* AIF1RX_CHAN0_DAT_INV */
+#define WM8996_AIF1RX_CHAN0_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN0_DAT_INV */
+#define WM8996_AIF1RX_CHAN0_DAT_INV_SHIFT 15 /* AIF1RX_CHAN0_DAT_INV */
+#define WM8996_AIF1RX_CHAN0_DAT_INV_WIDTH 1 /* AIF1RX_CHAN0_DAT_INV */
+#define WM8996_AIF1RX_CHAN0_SPACING_MASK 0x7E00 /* AIF1RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN0_SPACING_SHIFT 9 /* AIF1RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN0_SPACING_WIDTH 6 /* AIF1RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN0_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN0_SLOTS_SHIFT 6 /* AIF1RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN0_SLOTS_WIDTH 3 /* AIF1RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN0_START_SLOT_MASK 0x003F /* AIF1RX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN0_START_SLOT_SHIFT 0 /* AIF1RX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN0_START_SLOT_WIDTH 6 /* AIF1RX_CHAN0_START_SLOT - [5:0] */
+
+/*
+ * R784 (0x310) - AIF1RX Channel 1 Configuration
+ */
+#define WM8996_AIF1RX_CHAN1_DAT_INV 0x8000 /* AIF1RX_CHAN1_DAT_INV */
+#define WM8996_AIF1RX_CHAN1_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN1_DAT_INV */
+#define WM8996_AIF1RX_CHAN1_DAT_INV_SHIFT 15 /* AIF1RX_CHAN1_DAT_INV */
+#define WM8996_AIF1RX_CHAN1_DAT_INV_WIDTH 1 /* AIF1RX_CHAN1_DAT_INV */
+#define WM8996_AIF1RX_CHAN1_SPACING_MASK 0x7E00 /* AIF1RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN1_SPACING_SHIFT 9 /* AIF1RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN1_SPACING_WIDTH 6 /* AIF1RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN1_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN1_SLOTS_SHIFT 6 /* AIF1RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN1_SLOTS_WIDTH 3 /* AIF1RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN1_START_SLOT_MASK 0x003F /* AIF1RX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN1_START_SLOT_SHIFT 0 /* AIF1RX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN1_START_SLOT_WIDTH 6 /* AIF1RX_CHAN1_START_SLOT - [5:0] */
+
+/*
+ * R785 (0x311) - AIF1RX Channel 2 Configuration
+ */
+#define WM8996_AIF1RX_CHAN2_DAT_INV 0x8000 /* AIF1RX_CHAN2_DAT_INV */
+#define WM8996_AIF1RX_CHAN2_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN2_DAT_INV */
+#define WM8996_AIF1RX_CHAN2_DAT_INV_SHIFT 15 /* AIF1RX_CHAN2_DAT_INV */
+#define WM8996_AIF1RX_CHAN2_DAT_INV_WIDTH 1 /* AIF1RX_CHAN2_DAT_INV */
+#define WM8996_AIF1RX_CHAN2_SPACING_MASK 0x7E00 /* AIF1RX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN2_SPACING_SHIFT 9 /* AIF1RX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN2_SPACING_WIDTH 6 /* AIF1RX_CHAN2_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN2_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN2_SLOTS_SHIFT 6 /* AIF1RX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN2_SLOTS_WIDTH 3 /* AIF1RX_CHAN2_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN2_START_SLOT_MASK 0x003F /* AIF1RX_CHAN2_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN2_START_SLOT_SHIFT 0 /* AIF1RX_CHAN2_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN2_START_SLOT_WIDTH 6 /* AIF1RX_CHAN2_START_SLOT - [5:0] */
+
+/*
+ * R786 (0x312) - AIF1RX Channel 3 Configuration
+ */
+#define WM8996_AIF1RX_CHAN3_DAT_INV 0x8000 /* AIF1RX_CHAN3_DAT_INV */
+#define WM8996_AIF1RX_CHAN3_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN3_DAT_INV */
+#define WM8996_AIF1RX_CHAN3_DAT_INV_SHIFT 15 /* AIF1RX_CHAN3_DAT_INV */
+#define WM8996_AIF1RX_CHAN3_DAT_INV_WIDTH 1 /* AIF1RX_CHAN3_DAT_INV */
+#define WM8996_AIF1RX_CHAN3_SPACING_MASK 0x7E00 /* AIF1RX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN3_SPACING_SHIFT 9 /* AIF1RX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN3_SPACING_WIDTH 6 /* AIF1RX_CHAN3_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN3_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN3_SLOTS_SHIFT 6 /* AIF1RX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN3_SLOTS_WIDTH 3 /* AIF1RX_CHAN3_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN3_START_SLOT_MASK 0x003F /* AIF1RX_CHAN3_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN3_START_SLOT_SHIFT 0 /* AIF1RX_CHAN3_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN3_START_SLOT_WIDTH 6 /* AIF1RX_CHAN3_START_SLOT - [5:0] */
+
+/*
+ * R787 (0x313) - AIF1RX Channel 4 Configuration
+ */
+#define WM8996_AIF1RX_CHAN4_DAT_INV 0x8000 /* AIF1RX_CHAN4_DAT_INV */
+#define WM8996_AIF1RX_CHAN4_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN4_DAT_INV */
+#define WM8996_AIF1RX_CHAN4_DAT_INV_SHIFT 15 /* AIF1RX_CHAN4_DAT_INV */
+#define WM8996_AIF1RX_CHAN4_DAT_INV_WIDTH 1 /* AIF1RX_CHAN4_DAT_INV */
+#define WM8996_AIF1RX_CHAN4_SPACING_MASK 0x7E00 /* AIF1RX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN4_SPACING_SHIFT 9 /* AIF1RX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN4_SPACING_WIDTH 6 /* AIF1RX_CHAN4_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN4_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN4_SLOTS_SHIFT 6 /* AIF1RX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN4_SLOTS_WIDTH 3 /* AIF1RX_CHAN4_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN4_START_SLOT_MASK 0x003F /* AIF1RX_CHAN4_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN4_START_SLOT_SHIFT 0 /* AIF1RX_CHAN4_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN4_START_SLOT_WIDTH 6 /* AIF1RX_CHAN4_START_SLOT - [5:0] */
+
+/*
+ * R788 (0x314) - AIF1RX Channel 5 Configuration
+ */
+#define WM8996_AIF1RX_CHAN5_DAT_INV 0x8000 /* AIF1RX_CHAN5_DAT_INV */
+#define WM8996_AIF1RX_CHAN5_DAT_INV_MASK 0x8000 /* AIF1RX_CHAN5_DAT_INV */
+#define WM8996_AIF1RX_CHAN5_DAT_INV_SHIFT 15 /* AIF1RX_CHAN5_DAT_INV */
+#define WM8996_AIF1RX_CHAN5_DAT_INV_WIDTH 1 /* AIF1RX_CHAN5_DAT_INV */
+#define WM8996_AIF1RX_CHAN5_SPACING_MASK 0x7E00 /* AIF1RX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN5_SPACING_SHIFT 9 /* AIF1RX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN5_SPACING_WIDTH 6 /* AIF1RX_CHAN5_SPACING - [14:9] */
+#define WM8996_AIF1RX_CHAN5_SLOTS_MASK 0x01C0 /* AIF1RX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN5_SLOTS_SHIFT 6 /* AIF1RX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN5_SLOTS_WIDTH 3 /* AIF1RX_CHAN5_SLOTS - [8:6] */
+#define WM8996_AIF1RX_CHAN5_START_SLOT_MASK 0x003F /* AIF1RX_CHAN5_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN5_START_SLOT_SHIFT 0 /* AIF1RX_CHAN5_START_SLOT - [5:0] */
+#define WM8996_AIF1RX_CHAN5_START_SLOT_WIDTH 6 /* AIF1RX_CHAN5_START_SLOT - [5:0] */
+
+/*
+ * R789 (0x315) - AIF1RX Mono Configuration
+ */
+#define WM8996_AIF1RX_CHAN4_MONO_MODE 0x0004 /* AIF1RX_CHAN4_MONO_MODE */
+#define WM8996_AIF1RX_CHAN4_MONO_MODE_MASK 0x0004 /* AIF1RX_CHAN4_MONO_MODE */
+#define WM8996_AIF1RX_CHAN4_MONO_MODE_SHIFT 2 /* AIF1RX_CHAN4_MONO_MODE */
+#define WM8996_AIF1RX_CHAN4_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN4_MONO_MODE */
+#define WM8996_AIF1RX_CHAN2_MONO_MODE 0x0002 /* AIF1RX_CHAN2_MONO_MODE */
+#define WM8996_AIF1RX_CHAN2_MONO_MODE_MASK 0x0002 /* AIF1RX_CHAN2_MONO_MODE */
+#define WM8996_AIF1RX_CHAN2_MONO_MODE_SHIFT 1 /* AIF1RX_CHAN2_MONO_MODE */
+#define WM8996_AIF1RX_CHAN2_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN2_MONO_MODE */
+#define WM8996_AIF1RX_CHAN0_MONO_MODE 0x0001 /* AIF1RX_CHAN0_MONO_MODE */
+#define WM8996_AIF1RX_CHAN0_MONO_MODE_MASK 0x0001 /* AIF1RX_CHAN0_MONO_MODE */
+#define WM8996_AIF1RX_CHAN0_MONO_MODE_SHIFT 0 /* AIF1RX_CHAN0_MONO_MODE */
+#define WM8996_AIF1RX_CHAN0_MONO_MODE_WIDTH 1 /* AIF1RX_CHAN0_MONO_MODE */
+
+/*
+ * R794 (0x31A) - AIF1TX Test
+ */
+#define WM8996_AIF1TX45_DITHER_ENA 0x0004 /* AIF1TX45_DITHER_ENA */
+#define WM8996_AIF1TX45_DITHER_ENA_MASK 0x0004 /* AIF1TX45_DITHER_ENA */
+#define WM8996_AIF1TX45_DITHER_ENA_SHIFT 2 /* AIF1TX45_DITHER_ENA */
+#define WM8996_AIF1TX45_DITHER_ENA_WIDTH 1 /* AIF1TX45_DITHER_ENA */
+#define WM8996_AIF1TX23_DITHER_ENA 0x0002 /* AIF1TX23_DITHER_ENA */
+#define WM8996_AIF1TX23_DITHER_ENA_MASK 0x0002 /* AIF1TX23_DITHER_ENA */
+#define WM8996_AIF1TX23_DITHER_ENA_SHIFT 1 /* AIF1TX23_DITHER_ENA */
+#define WM8996_AIF1TX23_DITHER_ENA_WIDTH 1 /* AIF1TX23_DITHER_ENA */
+#define WM8996_AIF1TX01_DITHER_ENA 0x0001 /* AIF1TX01_DITHER_ENA */
+#define WM8996_AIF1TX01_DITHER_ENA_MASK 0x0001 /* AIF1TX01_DITHER_ENA */
+#define WM8996_AIF1TX01_DITHER_ENA_SHIFT 0 /* AIF1TX01_DITHER_ENA */
+#define WM8996_AIF1TX01_DITHER_ENA_WIDTH 1 /* AIF1TX01_DITHER_ENA */
+
+/*
+ * R800 (0x320) - AIF2 Control
+ */
+#define WM8996_AIF2_TRI 0x0004 /* AIF2_TRI */
+#define WM8996_AIF2_TRI_MASK 0x0004 /* AIF2_TRI */
+#define WM8996_AIF2_TRI_SHIFT 2 /* AIF2_TRI */
+#define WM8996_AIF2_TRI_WIDTH 1 /* AIF2_TRI */
+#define WM8996_AIF2_FMT_MASK 0x0003 /* AIF2_FMT - [1:0] */
+#define WM8996_AIF2_FMT_SHIFT 0 /* AIF2_FMT - [1:0] */
+#define WM8996_AIF2_FMT_WIDTH 2 /* AIF2_FMT - [1:0] */
+
+/*
+ * R801 (0x321) - AIF2 BCLK
+ */
+#define WM8996_AIF2_BCLK_INV 0x0400 /* AIF2_BCLK_INV */
+#define WM8996_AIF2_BCLK_INV_MASK 0x0400 /* AIF2_BCLK_INV */
+#define WM8996_AIF2_BCLK_INV_SHIFT 10 /* AIF2_BCLK_INV */
+#define WM8996_AIF2_BCLK_INV_WIDTH 1 /* AIF2_BCLK_INV */
+#define WM8996_AIF2_BCLK_FRC 0x0200 /* AIF2_BCLK_FRC */
+#define WM8996_AIF2_BCLK_FRC_MASK 0x0200 /* AIF2_BCLK_FRC */
+#define WM8996_AIF2_BCLK_FRC_SHIFT 9 /* AIF2_BCLK_FRC */
+#define WM8996_AIF2_BCLK_FRC_WIDTH 1 /* AIF2_BCLK_FRC */
+#define WM8996_AIF2_BCLK_MSTR 0x0100 /* AIF2_BCLK_MSTR */
+#define WM8996_AIF2_BCLK_MSTR_MASK 0x0100 /* AIF2_BCLK_MSTR */
+#define WM8996_AIF2_BCLK_MSTR_SHIFT 8 /* AIF2_BCLK_MSTR */
+#define WM8996_AIF2_BCLK_MSTR_WIDTH 1 /* AIF2_BCLK_MSTR */
+#define WM8996_AIF2_BCLK_DIV_MASK 0x000F /* AIF2_BCLK_DIV - [3:0] */
+#define WM8996_AIF2_BCLK_DIV_SHIFT 0 /* AIF2_BCLK_DIV - [3:0] */
+#define WM8996_AIF2_BCLK_DIV_WIDTH 4 /* AIF2_BCLK_DIV - [3:0] */
+
+/*
+ * R802 (0x322) - AIF2 TX LRCLK(1)
+ */
+#define WM8996_AIF2TX_RATE_MASK 0x07FF /* AIF2TX_RATE - [10:0] */
+#define WM8996_AIF2TX_RATE_SHIFT 0 /* AIF2TX_RATE - [10:0] */
+#define WM8996_AIF2TX_RATE_WIDTH 11 /* AIF2TX_RATE - [10:0] */
+
+/*
+ * R803 (0x323) - AIF2 TX LRCLK(2)
+ */
+#define WM8996_AIF2TX_LRCLK_MODE 0x0008 /* AIF2TX_LRCLK_MODE */
+#define WM8996_AIF2TX_LRCLK_MODE_MASK 0x0008 /* AIF2TX_LRCLK_MODE */
+#define WM8996_AIF2TX_LRCLK_MODE_SHIFT 3 /* AIF2TX_LRCLK_MODE */
+#define WM8996_AIF2TX_LRCLK_MODE_WIDTH 1 /* AIF2TX_LRCLK_MODE */
+#define WM8996_AIF2TX_LRCLK_INV 0x0004 /* AIF2TX_LRCLK_INV */
+#define WM8996_AIF2TX_LRCLK_INV_MASK 0x0004 /* AIF2TX_LRCLK_INV */
+#define WM8996_AIF2TX_LRCLK_INV_SHIFT 2 /* AIF2TX_LRCLK_INV */
+#define WM8996_AIF2TX_LRCLK_INV_WIDTH 1 /* AIF2TX_LRCLK_INV */
+#define WM8996_AIF2TX_LRCLK_FRC 0x0002 /* AIF2TX_LRCLK_FRC */
+#define WM8996_AIF2TX_LRCLK_FRC_MASK 0x0002 /* AIF2TX_LRCLK_FRC */
+#define WM8996_AIF2TX_LRCLK_FRC_SHIFT 1 /* AIF2TX_LRCLK_FRC */
+#define WM8996_AIF2TX_LRCLK_FRC_WIDTH 1 /* AIF2TX_LRCLK_FRC */
+#define WM8996_AIF2TX_LRCLK_MSTR 0x0001 /* AIF2TX_LRCLK_MSTR */
+#define WM8996_AIF2TX_LRCLK_MSTR_MASK 0x0001 /* AIF2TX_LRCLK_MSTR */
+#define WM8996_AIF2TX_LRCLK_MSTR_SHIFT 0 /* AIF2TX_LRCLK_MSTR */
+#define WM8996_AIF2TX_LRCLK_MSTR_WIDTH 1 /* AIF2TX_LRCLK_MSTR */
+
+/*
+ * R804 (0x324) - AIF2 RX LRCLK(1)
+ */
+#define WM8996_AIF2RX_RATE_MASK 0x07FF /* AIF2RX_RATE - [10:0] */
+#define WM8996_AIF2RX_RATE_SHIFT 0 /* AIF2RX_RATE - [10:0] */
+#define WM8996_AIF2RX_RATE_WIDTH 11 /* AIF2RX_RATE - [10:0] */
+
+/*
+ * R805 (0x325) - AIF2 RX LRCLK(2)
+ */
+#define WM8996_AIF2RX_LRCLK_INV 0x0004 /* AIF2RX_LRCLK_INV */
+#define WM8996_AIF2RX_LRCLK_INV_MASK 0x0004 /* AIF2RX_LRCLK_INV */
+#define WM8996_AIF2RX_LRCLK_INV_SHIFT 2 /* AIF2RX_LRCLK_INV */
+#define WM8996_AIF2RX_LRCLK_INV_WIDTH 1 /* AIF2RX_LRCLK_INV */
+#define WM8996_AIF2RX_LRCLK_FRC 0x0002 /* AIF2RX_LRCLK_FRC */
+#define WM8996_AIF2RX_LRCLK_FRC_MASK 0x0002 /* AIF2RX_LRCLK_FRC */
+#define WM8996_AIF2RX_LRCLK_FRC_SHIFT 1 /* AIF2RX_LRCLK_FRC */
+#define WM8996_AIF2RX_LRCLK_FRC_WIDTH 1 /* AIF2RX_LRCLK_FRC */
+#define WM8996_AIF2RX_LRCLK_MSTR 0x0001 /* AIF2RX_LRCLK_MSTR */
+#define WM8996_AIF2RX_LRCLK_MSTR_MASK 0x0001 /* AIF2RX_LRCLK_MSTR */
+#define WM8996_AIF2RX_LRCLK_MSTR_SHIFT 0 /* AIF2RX_LRCLK_MSTR */
+#define WM8996_AIF2RX_LRCLK_MSTR_WIDTH 1 /* AIF2RX_LRCLK_MSTR */
+
+/*
+ * R806 (0x326) - AIF2TX Data Configuration (1)
+ */
+#define WM8996_AIF2TX_WL_MASK 0xFF00 /* AIF2TX_WL - [15:8] */
+#define WM8996_AIF2TX_WL_SHIFT 8 /* AIF2TX_WL - [15:8] */
+#define WM8996_AIF2TX_WL_WIDTH 8 /* AIF2TX_WL - [15:8] */
+#define WM8996_AIF2TX_SLOT_LEN_MASK 0x00FF /* AIF2TX_SLOT_LEN - [7:0] */
+#define WM8996_AIF2TX_SLOT_LEN_SHIFT 0 /* AIF2TX_SLOT_LEN - [7:0] */
+#define WM8996_AIF2TX_SLOT_LEN_WIDTH 8 /* AIF2TX_SLOT_LEN - [7:0] */
+
+/*
+ * R807 (0x327) - AIF2TX Data Configuration (2)
+ */
+#define WM8996_AIF2TX_DAT_TRI 0x0001 /* AIF2TX_DAT_TRI */
+#define WM8996_AIF2TX_DAT_TRI_MASK 0x0001 /* AIF2TX_DAT_TRI */
+#define WM8996_AIF2TX_DAT_TRI_SHIFT 0 /* AIF2TX_DAT_TRI */
+#define WM8996_AIF2TX_DAT_TRI_WIDTH 1 /* AIF2TX_DAT_TRI */
+
+/*
+ * R808 (0x328) - AIF2RX Data Configuration
+ */
+#define WM8996_AIF2RX_WL_MASK 0xFF00 /* AIF2RX_WL - [15:8] */
+#define WM8996_AIF2RX_WL_SHIFT 8 /* AIF2RX_WL - [15:8] */
+#define WM8996_AIF2RX_WL_WIDTH 8 /* AIF2RX_WL - [15:8] */
+#define WM8996_AIF2RX_SLOT_LEN_MASK 0x00FF /* AIF2RX_SLOT_LEN - [7:0] */
+#define WM8996_AIF2RX_SLOT_LEN_SHIFT 0 /* AIF2RX_SLOT_LEN - [7:0] */
+#define WM8996_AIF2RX_SLOT_LEN_WIDTH 8 /* AIF2RX_SLOT_LEN - [7:0] */
+
+/*
+ * R809 (0x329) - AIF2TX Channel 0 Configuration
+ */
+#define WM8996_AIF2TX_CHAN0_DAT_INV 0x8000 /* AIF2TX_CHAN0_DAT_INV */
+#define WM8996_AIF2TX_CHAN0_DAT_INV_MASK 0x8000 /* AIF2TX_CHAN0_DAT_INV */
+#define WM8996_AIF2TX_CHAN0_DAT_INV_SHIFT 15 /* AIF2TX_CHAN0_DAT_INV */
+#define WM8996_AIF2TX_CHAN0_DAT_INV_WIDTH 1 /* AIF2TX_CHAN0_DAT_INV */
+#define WM8996_AIF2TX_CHAN0_SPACING_MASK 0x7E00 /* AIF2TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN0_SPACING_SHIFT 9 /* AIF2TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN0_SPACING_WIDTH 6 /* AIF2TX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN0_SLOTS_MASK 0x01C0 /* AIF2TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN0_SLOTS_SHIFT 6 /* AIF2TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN0_SLOTS_WIDTH 3 /* AIF2TX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN0_START_SLOT_MASK 0x003F /* AIF2TX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF2TX_CHAN0_START_SLOT_SHIFT 0 /* AIF2TX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF2TX_CHAN0_START_SLOT_WIDTH 6 /* AIF2TX_CHAN0_START_SLOT - [5:0] */
+
+/*
+ * R810 (0x32A) - AIF2TX Channel 1 Configuration
+ */
+#define WM8996_AIF2TX_CHAN1_DAT_INV 0x8000 /* AIF2TX_CHAN1_DAT_INV */
+#define WM8996_AIF2TX_CHAN1_DAT_INV_MASK 0x8000 /* AIF2TX_CHAN1_DAT_INV */
+#define WM8996_AIF2TX_CHAN1_DAT_INV_SHIFT 15 /* AIF2TX_CHAN1_DAT_INV */
+#define WM8996_AIF2TX_CHAN1_DAT_INV_WIDTH 1 /* AIF2TX_CHAN1_DAT_INV */
+#define WM8996_AIF2TX_CHAN1_SPACING_MASK 0x7E00 /* AIF2TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN1_SPACING_SHIFT 9 /* AIF2TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN1_SPACING_WIDTH 6 /* AIF2TX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2TX_CHAN1_SLOTS_MASK 0x01C0 /* AIF2TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN1_SLOTS_SHIFT 6 /* AIF2TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN1_SLOTS_WIDTH 3 /* AIF2TX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2TX_CHAN1_START_SLOT_MASK 0x003F /* AIF2TX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF2TX_CHAN1_START_SLOT_SHIFT 0 /* AIF2TX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF2TX_CHAN1_START_SLOT_WIDTH 6 /* AIF2TX_CHAN1_START_SLOT - [5:0] */
+
+/*
+ * R811 (0x32B) - AIF2RX Channel 0 Configuration
+ */
+#define WM8996_AIF2RX_CHAN0_DAT_INV 0x8000 /* AIF2RX_CHAN0_DAT_INV */
+#define WM8996_AIF2RX_CHAN0_DAT_INV_MASK 0x8000 /* AIF2RX_CHAN0_DAT_INV */
+#define WM8996_AIF2RX_CHAN0_DAT_INV_SHIFT 15 /* AIF2RX_CHAN0_DAT_INV */
+#define WM8996_AIF2RX_CHAN0_DAT_INV_WIDTH 1 /* AIF2RX_CHAN0_DAT_INV */
+#define WM8996_AIF2RX_CHAN0_SPACING_MASK 0x7E00 /* AIF2RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN0_SPACING_SHIFT 9 /* AIF2RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN0_SPACING_WIDTH 6 /* AIF2RX_CHAN0_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN0_SLOTS_MASK 0x01C0 /* AIF2RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN0_SLOTS_SHIFT 6 /* AIF2RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN0_SLOTS_WIDTH 3 /* AIF2RX_CHAN0_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN0_START_SLOT_MASK 0x003F /* AIF2RX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF2RX_CHAN0_START_SLOT_SHIFT 0 /* AIF2RX_CHAN0_START_SLOT - [5:0] */
+#define WM8996_AIF2RX_CHAN0_START_SLOT_WIDTH 6 /* AIF2RX_CHAN0_START_SLOT - [5:0] */
+
+/*
+ * R812 (0x32C) - AIF2RX Channel 1 Configuration
+ */
+#define WM8996_AIF2RX_CHAN1_DAT_INV 0x8000 /* AIF2RX_CHAN1_DAT_INV */
+#define WM8996_AIF2RX_CHAN1_DAT_INV_MASK 0x8000 /* AIF2RX_CHAN1_DAT_INV */
+#define WM8996_AIF2RX_CHAN1_DAT_INV_SHIFT 15 /* AIF2RX_CHAN1_DAT_INV */
+#define WM8996_AIF2RX_CHAN1_DAT_INV_WIDTH 1 /* AIF2RX_CHAN1_DAT_INV */
+#define WM8996_AIF2RX_CHAN1_SPACING_MASK 0x7E00 /* AIF2RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN1_SPACING_SHIFT 9 /* AIF2RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN1_SPACING_WIDTH 6 /* AIF2RX_CHAN1_SPACING - [14:9] */
+#define WM8996_AIF2RX_CHAN1_SLOTS_MASK 0x01C0 /* AIF2RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN1_SLOTS_SHIFT 6 /* AIF2RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN1_SLOTS_WIDTH 3 /* AIF2RX_CHAN1_SLOTS - [8:6] */
+#define WM8996_AIF2RX_CHAN1_START_SLOT_MASK 0x003F /* AIF2RX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF2RX_CHAN1_START_SLOT_SHIFT 0 /* AIF2RX_CHAN1_START_SLOT - [5:0] */
+#define WM8996_AIF2RX_CHAN1_START_SLOT_WIDTH 6 /* AIF2RX_CHAN1_START_SLOT - [5:0] */
+
+/*
+ * R813 (0x32D) - AIF2RX Mono Configuration
+ */
+#define WM8996_AIF2RX_CHAN0_MONO_MODE 0x0001 /* AIF2RX_CHAN0_MONO_MODE */
+#define WM8996_AIF2RX_CHAN0_MONO_MODE_MASK 0x0001 /* AIF2RX_CHAN0_MONO_MODE */
+#define WM8996_AIF2RX_CHAN0_MONO_MODE_SHIFT 0 /* AIF2RX_CHAN0_MONO_MODE */
+#define WM8996_AIF2RX_CHAN0_MONO_MODE_WIDTH 1 /* AIF2RX_CHAN0_MONO_MODE */
+
+/*
+ * R815 (0x32F) - AIF2TX Test
+ */
+#define WM8996_AIF2TX_DITHER_ENA 0x0001 /* AIF2TX_DITHER_ENA */
+#define WM8996_AIF2TX_DITHER_ENA_MASK 0x0001 /* AIF2TX_DITHER_ENA */
+#define WM8996_AIF2TX_DITHER_ENA_SHIFT 0 /* AIF2TX_DITHER_ENA */
+#define WM8996_AIF2TX_DITHER_ENA_WIDTH 1 /* AIF2TX_DITHER_ENA */
+
+/*
+ * R1024 (0x400) - DSP1 TX Left Volume
+ */
+#define WM8996_DSP1TX_VU 0x0100 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_MASK 0x0100 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_SHIFT 8 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_WIDTH 1 /* DSP1TX_VU */
+#define WM8996_DSP1TXL_VOL_MASK 0x00FF /* DSP1TXL_VOL - [7:0] */
+#define WM8996_DSP1TXL_VOL_SHIFT 0 /* DSP1TXL_VOL - [7:0] */
+#define WM8996_DSP1TXL_VOL_WIDTH 8 /* DSP1TXL_VOL - [7:0] */
+
+/*
+ * R1025 (0x401) - DSP1 TX Right Volume
+ */
+#define WM8996_DSP1TX_VU 0x0100 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_MASK 0x0100 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_SHIFT 8 /* DSP1TX_VU */
+#define WM8996_DSP1TX_VU_WIDTH 1 /* DSP1TX_VU */
+#define WM8996_DSP1TXR_VOL_MASK 0x00FF /* DSP1TXR_VOL - [7:0] */
+#define WM8996_DSP1TXR_VOL_SHIFT 0 /* DSP1TXR_VOL - [7:0] */
+#define WM8996_DSP1TXR_VOL_WIDTH 8 /* DSP1TXR_VOL - [7:0] */
+
+/*
+ * R1026 (0x402) - DSP1 RX Left Volume
+ */
+#define WM8996_DSP1RX_VU 0x0100 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_MASK 0x0100 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_SHIFT 8 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_WIDTH 1 /* DSP1RX_VU */
+#define WM8996_DSP1RXL_VOL_MASK 0x00FF /* DSP1RXL_VOL - [7:0] */
+#define WM8996_DSP1RXL_VOL_SHIFT 0 /* DSP1RXL_VOL - [7:0] */
+#define WM8996_DSP1RXL_VOL_WIDTH 8 /* DSP1RXL_VOL - [7:0] */
+
+/*
+ * R1027 (0x403) - DSP1 RX Right Volume
+ */
+#define WM8996_DSP1RX_VU 0x0100 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_MASK 0x0100 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_SHIFT 8 /* DSP1RX_VU */
+#define WM8996_DSP1RX_VU_WIDTH 1 /* DSP1RX_VU */
+#define WM8996_DSP1RXR_VOL_MASK 0x00FF /* DSP1RXR_VOL - [7:0] */
+#define WM8996_DSP1RXR_VOL_SHIFT 0 /* DSP1RXR_VOL - [7:0] */
+#define WM8996_DSP1RXR_VOL_WIDTH 8 /* DSP1RXR_VOL - [7:0] */
+
+/*
+ * R1040 (0x410) - DSP1 TX Filters
+ */
+#define WM8996_DSP1TX_NF 0x2000 /* DSP1TX_NF */
+#define WM8996_DSP1TX_NF_MASK 0x2000 /* DSP1TX_NF */
+#define WM8996_DSP1TX_NF_SHIFT 13 /* DSP1TX_NF */
+#define WM8996_DSP1TX_NF_WIDTH 1 /* DSP1TX_NF */
+#define WM8996_DSP1TXL_HPF 0x1000 /* DSP1TXL_HPF */
+#define WM8996_DSP1TXL_HPF_MASK 0x1000 /* DSP1TXL_HPF */
+#define WM8996_DSP1TXL_HPF_SHIFT 12 /* DSP1TXL_HPF */
+#define WM8996_DSP1TXL_HPF_WIDTH 1 /* DSP1TXL_HPF */
+#define WM8996_DSP1TXR_HPF 0x0800 /* DSP1TXR_HPF */
+#define WM8996_DSP1TXR_HPF_MASK 0x0800 /* DSP1TXR_HPF */
+#define WM8996_DSP1TXR_HPF_SHIFT 11 /* DSP1TXR_HPF */
+#define WM8996_DSP1TXR_HPF_WIDTH 1 /* DSP1TXR_HPF */
+#define WM8996_DSP1TX_HPF_MODE_MASK 0x0018 /* DSP1TX_HPF_MODE - [4:3] */
+#define WM8996_DSP1TX_HPF_MODE_SHIFT 3 /* DSP1TX_HPF_MODE - [4:3] */
+#define WM8996_DSP1TX_HPF_MODE_WIDTH 2 /* DSP1TX_HPF_MODE - [4:3] */
+#define WM8996_DSP1TX_HPF_CUT_MASK 0x0007 /* DSP1TX_HPF_CUT - [2:0] */
+#define WM8996_DSP1TX_HPF_CUT_SHIFT 0 /* DSP1TX_HPF_CUT - [2:0] */
+#define WM8996_DSP1TX_HPF_CUT_WIDTH 3 /* DSP1TX_HPF_CUT - [2:0] */
+
+/*
+ * R1056 (0x420) - DSP1 RX Filters (1)
+ */
+#define WM8996_DSP1RX_MUTE 0x0200 /* DSP1RX_MUTE */
+#define WM8996_DSP1RX_MUTE_MASK 0x0200 /* DSP1RX_MUTE */
+#define WM8996_DSP1RX_MUTE_SHIFT 9 /* DSP1RX_MUTE */
+#define WM8996_DSP1RX_MUTE_WIDTH 1 /* DSP1RX_MUTE */
+#define WM8996_DSP1RX_MONO 0x0080 /* DSP1RX_MONO */
+#define WM8996_DSP1RX_MONO_MASK 0x0080 /* DSP1RX_MONO */
+#define WM8996_DSP1RX_MONO_SHIFT 7 /* DSP1RX_MONO */
+#define WM8996_DSP1RX_MONO_WIDTH 1 /* DSP1RX_MONO */
+#define WM8996_DSP1RX_MUTERATE 0x0020 /* DSP1RX_MUTERATE */
+#define WM8996_DSP1RX_MUTERATE_MASK 0x0020 /* DSP1RX_MUTERATE */
+#define WM8996_DSP1RX_MUTERATE_SHIFT 5 /* DSP1RX_MUTERATE */
+#define WM8996_DSP1RX_MUTERATE_WIDTH 1 /* DSP1RX_MUTERATE */
+#define WM8996_DSP1RX_UNMUTE_RAMP 0x0010 /* DSP1RX_UNMUTE_RAMP */
+#define WM8996_DSP1RX_UNMUTE_RAMP_MASK 0x0010 /* DSP1RX_UNMUTE_RAMP */
+#define WM8996_DSP1RX_UNMUTE_RAMP_SHIFT 4 /* DSP1RX_UNMUTE_RAMP */
+#define WM8996_DSP1RX_UNMUTE_RAMP_WIDTH 1 /* DSP1RX_UNMUTE_RAMP */
+
+/*
+ * R1057 (0x421) - DSP1 RX Filters (2)
+ */
+#define WM8996_DSP1RX_3D_GAIN_MASK 0x3E00 /* DSP1RX_3D_GAIN - [13:9] */
+#define WM8996_DSP1RX_3D_GAIN_SHIFT 9 /* DSP1RX_3D_GAIN - [13:9] */
+#define WM8996_DSP1RX_3D_GAIN_WIDTH 5 /* DSP1RX_3D_GAIN - [13:9] */
+#define WM8996_DSP1RX_3D_ENA 0x0100 /* DSP1RX_3D_ENA */
+#define WM8996_DSP1RX_3D_ENA_MASK 0x0100 /* DSP1RX_3D_ENA */
+#define WM8996_DSP1RX_3D_ENA_SHIFT 8 /* DSP1RX_3D_ENA */
+#define WM8996_DSP1RX_3D_ENA_WIDTH 1 /* DSP1RX_3D_ENA */
+
+/*
+ * R1088 (0x440) - DSP1 DRC (1)
+ */
+#define WM8996_DSP1DRC_SIG_DET_RMS_MASK 0xF800 /* DSP1DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP1DRC_SIG_DET_RMS_SHIFT 11 /* DSP1DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP1DRC_SIG_DET_RMS_WIDTH 5 /* DSP1DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP1DRC_SIG_DET_PK_MASK 0x0600 /* DSP1DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP1DRC_SIG_DET_PK_SHIFT 9 /* DSP1DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP1DRC_SIG_DET_PK_WIDTH 2 /* DSP1DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP1DRC_NG_ENA 0x0100 /* DSP1DRC_NG_ENA */
+#define WM8996_DSP1DRC_NG_ENA_MASK 0x0100 /* DSP1DRC_NG_ENA */
+#define WM8996_DSP1DRC_NG_ENA_SHIFT 8 /* DSP1DRC_NG_ENA */
+#define WM8996_DSP1DRC_NG_ENA_WIDTH 1 /* DSP1DRC_NG_ENA */
+#define WM8996_DSP1DRC_SIG_DET_MODE 0x0080 /* DSP1DRC_SIG_DET_MODE */
+#define WM8996_DSP1DRC_SIG_DET_MODE_MASK 0x0080 /* DSP1DRC_SIG_DET_MODE */
+#define WM8996_DSP1DRC_SIG_DET_MODE_SHIFT 7 /* DSP1DRC_SIG_DET_MODE */
+#define WM8996_DSP1DRC_SIG_DET_MODE_WIDTH 1 /* DSP1DRC_SIG_DET_MODE */
+#define WM8996_DSP1DRC_SIG_DET 0x0040 /* DSP1DRC_SIG_DET */
+#define WM8996_DSP1DRC_SIG_DET_MASK 0x0040 /* DSP1DRC_SIG_DET */
+#define WM8996_DSP1DRC_SIG_DET_SHIFT 6 /* DSP1DRC_SIG_DET */
+#define WM8996_DSP1DRC_SIG_DET_WIDTH 1 /* DSP1DRC_SIG_DET */
+#define WM8996_DSP1DRC_KNEE2_OP_ENA 0x0020 /* DSP1DRC_KNEE2_OP_ENA */
+#define WM8996_DSP1DRC_KNEE2_OP_ENA_MASK 0x0020 /* DSP1DRC_KNEE2_OP_ENA */
+#define WM8996_DSP1DRC_KNEE2_OP_ENA_SHIFT 5 /* DSP1DRC_KNEE2_OP_ENA */
+#define WM8996_DSP1DRC_KNEE2_OP_ENA_WIDTH 1 /* DSP1DRC_KNEE2_OP_ENA */
+#define WM8996_DSP1DRC_QR 0x0010 /* DSP1DRC_QR */
+#define WM8996_DSP1DRC_QR_MASK 0x0010 /* DSP1DRC_QR */
+#define WM8996_DSP1DRC_QR_SHIFT 4 /* DSP1DRC_QR */
+#define WM8996_DSP1DRC_QR_WIDTH 1 /* DSP1DRC_QR */
+#define WM8996_DSP1DRC_ANTICLIP 0x0008 /* DSP1DRC_ANTICLIP */
+#define WM8996_DSP1DRC_ANTICLIP_MASK 0x0008 /* DSP1DRC_ANTICLIP */
+#define WM8996_DSP1DRC_ANTICLIP_SHIFT 3 /* DSP1DRC_ANTICLIP */
+#define WM8996_DSP1DRC_ANTICLIP_WIDTH 1 /* DSP1DRC_ANTICLIP */
+#define WM8996_DSP1RX_DRC_ENA 0x0004 /* DSP1RX_DRC_ENA */
+#define WM8996_DSP1RX_DRC_ENA_MASK 0x0004 /* DSP1RX_DRC_ENA */
+#define WM8996_DSP1RX_DRC_ENA_SHIFT 2 /* DSP1RX_DRC_ENA */
+#define WM8996_DSP1RX_DRC_ENA_WIDTH 1 /* DSP1RX_DRC_ENA */
+#define WM8996_DSP1TXL_DRC_ENA 0x0002 /* DSP1TXL_DRC_ENA */
+#define WM8996_DSP1TXL_DRC_ENA_MASK 0x0002 /* DSP1TXL_DRC_ENA */
+#define WM8996_DSP1TXL_DRC_ENA_SHIFT 1 /* DSP1TXL_DRC_ENA */
+#define WM8996_DSP1TXL_DRC_ENA_WIDTH 1 /* DSP1TXL_DRC_ENA */
+#define WM8996_DSP1TXR_DRC_ENA 0x0001 /* DSP1TXR_DRC_ENA */
+#define WM8996_DSP1TXR_DRC_ENA_MASK 0x0001 /* DSP1TXR_DRC_ENA */
+#define WM8996_DSP1TXR_DRC_ENA_SHIFT 0 /* DSP1TXR_DRC_ENA */
+#define WM8996_DSP1TXR_DRC_ENA_WIDTH 1 /* DSP1TXR_DRC_ENA */
+
+/*
+ * R1089 (0x441) - DSP1 DRC (2)
+ */
+#define WM8996_DSP1DRC_ATK_MASK 0x1E00 /* DSP1DRC_ATK - [12:9] */
+#define WM8996_DSP1DRC_ATK_SHIFT 9 /* DSP1DRC_ATK - [12:9] */
+#define WM8996_DSP1DRC_ATK_WIDTH 4 /* DSP1DRC_ATK - [12:9] */
+#define WM8996_DSP1DRC_DCY_MASK 0x01E0 /* DSP1DRC_DCY - [8:5] */
+#define WM8996_DSP1DRC_DCY_SHIFT 5 /* DSP1DRC_DCY - [8:5] */
+#define WM8996_DSP1DRC_DCY_WIDTH 4 /* DSP1DRC_DCY - [8:5] */
+#define WM8996_DSP1DRC_MINGAIN_MASK 0x001C /* DSP1DRC_MINGAIN - [4:2] */
+#define WM8996_DSP1DRC_MINGAIN_SHIFT 2 /* DSP1DRC_MINGAIN - [4:2] */
+#define WM8996_DSP1DRC_MINGAIN_WIDTH 3 /* DSP1DRC_MINGAIN - [4:2] */
+#define WM8996_DSP1DRC_MAXGAIN_MASK 0x0003 /* DSP1DRC_MAXGAIN - [1:0] */
+#define WM8996_DSP1DRC_MAXGAIN_SHIFT 0 /* DSP1DRC_MAXGAIN - [1:0] */
+#define WM8996_DSP1DRC_MAXGAIN_WIDTH 2 /* DSP1DRC_MAXGAIN - [1:0] */
+
+/*
+ * R1090 (0x442) - DSP1 DRC (3)
+ */
+#define WM8996_DSP1DRC_NG_MINGAIN_MASK 0xF000 /* DSP1DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP1DRC_NG_MINGAIN_SHIFT 12 /* DSP1DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP1DRC_NG_MINGAIN_WIDTH 4 /* DSP1DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP1DRC_NG_EXP_MASK 0x0C00 /* DSP1DRC_NG_EXP - [11:10] */
+#define WM8996_DSP1DRC_NG_EXP_SHIFT 10 /* DSP1DRC_NG_EXP - [11:10] */
+#define WM8996_DSP1DRC_NG_EXP_WIDTH 2 /* DSP1DRC_NG_EXP - [11:10] */
+#define WM8996_DSP1DRC_QR_THR_MASK 0x0300 /* DSP1DRC_QR_THR - [9:8] */
+#define WM8996_DSP1DRC_QR_THR_SHIFT 8 /* DSP1DRC_QR_THR - [9:8] */
+#define WM8996_DSP1DRC_QR_THR_WIDTH 2 /* DSP1DRC_QR_THR - [9:8] */
+#define WM8996_DSP1DRC_QR_DCY_MASK 0x00C0 /* DSP1DRC_QR_DCY - [7:6] */
+#define WM8996_DSP1DRC_QR_DCY_SHIFT 6 /* DSP1DRC_QR_DCY - [7:6] */
+#define WM8996_DSP1DRC_QR_DCY_WIDTH 2 /* DSP1DRC_QR_DCY - [7:6] */
+#define WM8996_DSP1DRC_HI_COMP_MASK 0x0038 /* DSP1DRC_HI_COMP - [5:3] */
+#define WM8996_DSP1DRC_HI_COMP_SHIFT 3 /* DSP1DRC_HI_COMP - [5:3] */
+#define WM8996_DSP1DRC_HI_COMP_WIDTH 3 /* DSP1DRC_HI_COMP - [5:3] */
+#define WM8996_DSP1DRC_LO_COMP_MASK 0x0007 /* DSP1DRC_LO_COMP - [2:0] */
+#define WM8996_DSP1DRC_LO_COMP_SHIFT 0 /* DSP1DRC_LO_COMP - [2:0] */
+#define WM8996_DSP1DRC_LO_COMP_WIDTH 3 /* DSP1DRC_LO_COMP - [2:0] */
+
+/*
+ * R1091 (0x443) - DSP1 DRC (4)
+ */
+#define WM8996_DSP1DRC_KNEE_IP_MASK 0x07E0 /* DSP1DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP1DRC_KNEE_IP_SHIFT 5 /* DSP1DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP1DRC_KNEE_IP_WIDTH 6 /* DSP1DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP1DRC_KNEE_OP_MASK 0x001F /* DSP1DRC_KNEE_OP - [4:0] */
+#define WM8996_DSP1DRC_KNEE_OP_SHIFT 0 /* DSP1DRC_KNEE_OP - [4:0] */
+#define WM8996_DSP1DRC_KNEE_OP_WIDTH 5 /* DSP1DRC_KNEE_OP - [4:0] */
+
+/*
+ * R1092 (0x444) - DSP1 DRC (5)
+ */
+#define WM8996_DSP1DRC_KNEE2_IP_MASK 0x03E0 /* DSP1DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP1DRC_KNEE2_IP_SHIFT 5 /* DSP1DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP1DRC_KNEE2_IP_WIDTH 5 /* DSP1DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP1DRC_KNEE2_OP_MASK 0x001F /* DSP1DRC_KNEE2_OP - [4:0] */
+#define WM8996_DSP1DRC_KNEE2_OP_SHIFT 0 /* DSP1DRC_KNEE2_OP - [4:0] */
+#define WM8996_DSP1DRC_KNEE2_OP_WIDTH 5 /* DSP1DRC_KNEE2_OP - [4:0] */
+
+/*
+ * R1152 (0x480) - DSP1 RX EQ Gains (1)
+ */
+#define WM8996_DSP1RX_EQ_B1_GAIN_MASK 0xF800 /* DSP1RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B1_GAIN_SHIFT 11 /* DSP1RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B1_GAIN_WIDTH 5 /* DSP1RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B2_GAIN_MASK 0x07C0 /* DSP1RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP1RX_EQ_B2_GAIN_SHIFT 6 /* DSP1RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP1RX_EQ_B2_GAIN_WIDTH 5 /* DSP1RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP1RX_EQ_B3_GAIN_MASK 0x003E /* DSP1RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP1RX_EQ_B3_GAIN_SHIFT 1 /* DSP1RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP1RX_EQ_B3_GAIN_WIDTH 5 /* DSP1RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP1RX_EQ_ENA 0x0001 /* DSP1RX_EQ_ENA */
+#define WM8996_DSP1RX_EQ_ENA_MASK 0x0001 /* DSP1RX_EQ_ENA */
+#define WM8996_DSP1RX_EQ_ENA_SHIFT 0 /* DSP1RX_EQ_ENA */
+#define WM8996_DSP1RX_EQ_ENA_WIDTH 1 /* DSP1RX_EQ_ENA */
+
+/*
+ * R1153 (0x481) - DSP1 RX EQ Gains (2)
+ */
+#define WM8996_DSP1RX_EQ_B4_GAIN_MASK 0xF800 /* DSP1RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B4_GAIN_SHIFT 11 /* DSP1RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B4_GAIN_WIDTH 5 /* DSP1RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP1RX_EQ_B5_GAIN_MASK 0x07C0 /* DSP1RX_EQ_B5_GAIN - [10:6] */
+#define WM8996_DSP1RX_EQ_B5_GAIN_SHIFT 6 /* DSP1RX_EQ_B5_GAIN - [10:6] */
+#define WM8996_DSP1RX_EQ_B5_GAIN_WIDTH 5 /* DSP1RX_EQ_B5_GAIN - [10:6] */
+
+/*
+ * R1154 (0x482) - DSP1 RX EQ Band 1 A
+ */
+#define WM8996_DSP1RX_EQ_B1_A_MASK 0xFFFF /* DSP1RX_EQ_B1_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_A_SHIFT 0 /* DSP1RX_EQ_B1_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_A_WIDTH 16 /* DSP1RX_EQ_B1_A - [15:0] */
+
+/*
+ * R1155 (0x483) - DSP1 RX EQ Band 1 B
+ */
+#define WM8996_DSP1RX_EQ_B1_B_MASK 0xFFFF /* DSP1RX_EQ_B1_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_B_SHIFT 0 /* DSP1RX_EQ_B1_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_B_WIDTH 16 /* DSP1RX_EQ_B1_B - [15:0] */
+
+/*
+ * R1156 (0x484) - DSP1 RX EQ Band 1 PG
+ */
+#define WM8996_DSP1RX_EQ_B1_PG_MASK 0xFFFF /* DSP1RX_EQ_B1_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_PG_SHIFT 0 /* DSP1RX_EQ_B1_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B1_PG_WIDTH 16 /* DSP1RX_EQ_B1_PG - [15:0] */
+
+/*
+ * R1157 (0x485) - DSP1 RX EQ Band 2 A
+ */
+#define WM8996_DSP1RX_EQ_B2_A_MASK 0xFFFF /* DSP1RX_EQ_B2_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_A_SHIFT 0 /* DSP1RX_EQ_B2_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_A_WIDTH 16 /* DSP1RX_EQ_B2_A - [15:0] */
+
+/*
+ * R1158 (0x486) - DSP1 RX EQ Band 2 B
+ */
+#define WM8996_DSP1RX_EQ_B2_B_MASK 0xFFFF /* DSP1RX_EQ_B2_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_B_SHIFT 0 /* DSP1RX_EQ_B2_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_B_WIDTH 16 /* DSP1RX_EQ_B2_B - [15:0] */
+
+/*
+ * R1159 (0x487) - DSP1 RX EQ Band 2 C
+ */
+#define WM8996_DSP1RX_EQ_B2_C_MASK 0xFFFF /* DSP1RX_EQ_B2_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_C_SHIFT 0 /* DSP1RX_EQ_B2_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_C_WIDTH 16 /* DSP1RX_EQ_B2_C - [15:0] */
+
+/*
+ * R1160 (0x488) - DSP1 RX EQ Band 2 PG
+ */
+#define WM8996_DSP1RX_EQ_B2_PG_MASK 0xFFFF /* DSP1RX_EQ_B2_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_PG_SHIFT 0 /* DSP1RX_EQ_B2_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B2_PG_WIDTH 16 /* DSP1RX_EQ_B2_PG - [15:0] */
+
+/*
+ * R1161 (0x489) - DSP1 RX EQ Band 3 A
+ */
+#define WM8996_DSP1RX_EQ_B3_A_MASK 0xFFFF /* DSP1RX_EQ_B3_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_A_SHIFT 0 /* DSP1RX_EQ_B3_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_A_WIDTH 16 /* DSP1RX_EQ_B3_A - [15:0] */
+
+/*
+ * R1162 (0x48A) - DSP1 RX EQ Band 3 B
+ */
+#define WM8996_DSP1RX_EQ_B3_B_MASK 0xFFFF /* DSP1RX_EQ_B3_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_B_SHIFT 0 /* DSP1RX_EQ_B3_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_B_WIDTH 16 /* DSP1RX_EQ_B3_B - [15:0] */
+
+/*
+ * R1163 (0x48B) - DSP1 RX EQ Band 3 C
+ */
+#define WM8996_DSP1RX_EQ_B3_C_MASK 0xFFFF /* DSP1RX_EQ_B3_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_C_SHIFT 0 /* DSP1RX_EQ_B3_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_C_WIDTH 16 /* DSP1RX_EQ_B3_C - [15:0] */
+
+/*
+ * R1164 (0x48C) - DSP1 RX EQ Band 3 PG
+ */
+#define WM8996_DSP1RX_EQ_B3_PG_MASK 0xFFFF /* DSP1RX_EQ_B3_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_PG_SHIFT 0 /* DSP1RX_EQ_B3_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B3_PG_WIDTH 16 /* DSP1RX_EQ_B3_PG - [15:0] */
+
+/*
+ * R1165 (0x48D) - DSP1 RX EQ Band 4 A
+ */
+#define WM8996_DSP1RX_EQ_B4_A_MASK 0xFFFF /* DSP1RX_EQ_B4_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_A_SHIFT 0 /* DSP1RX_EQ_B4_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_A_WIDTH 16 /* DSP1RX_EQ_B4_A - [15:0] */
+
+/*
+ * R1166 (0x48E) - DSP1 RX EQ Band 4 B
+ */
+#define WM8996_DSP1RX_EQ_B4_B_MASK 0xFFFF /* DSP1RX_EQ_B4_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_B_SHIFT 0 /* DSP1RX_EQ_B4_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_B_WIDTH 16 /* DSP1RX_EQ_B4_B - [15:0] */
+
+/*
+ * R1167 (0x48F) - DSP1 RX EQ Band 4 C
+ */
+#define WM8996_DSP1RX_EQ_B4_C_MASK 0xFFFF /* DSP1RX_EQ_B4_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_C_SHIFT 0 /* DSP1RX_EQ_B4_C - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_C_WIDTH 16 /* DSP1RX_EQ_B4_C - [15:0] */
+
+/*
+ * R1168 (0x490) - DSP1 RX EQ Band 4 PG
+ */
+#define WM8996_DSP1RX_EQ_B4_PG_MASK 0xFFFF /* DSP1RX_EQ_B4_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_PG_SHIFT 0 /* DSP1RX_EQ_B4_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B4_PG_WIDTH 16 /* DSP1RX_EQ_B4_PG - [15:0] */
+
+/*
+ * R1169 (0x491) - DSP1 RX EQ Band 5 A
+ */
+#define WM8996_DSP1RX_EQ_B5_A_MASK 0xFFFF /* DSP1RX_EQ_B5_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_A_SHIFT 0 /* DSP1RX_EQ_B5_A - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_A_WIDTH 16 /* DSP1RX_EQ_B5_A - [15:0] */
+
+/*
+ * R1170 (0x492) - DSP1 RX EQ Band 5 B
+ */
+#define WM8996_DSP1RX_EQ_B5_B_MASK 0xFFFF /* DSP1RX_EQ_B5_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_B_SHIFT 0 /* DSP1RX_EQ_B5_B - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_B_WIDTH 16 /* DSP1RX_EQ_B5_B - [15:0] */
+
+/*
+ * R1171 (0x493) - DSP1 RX EQ Band 5 PG
+ */
+#define WM8996_DSP1RX_EQ_B5_PG_MASK 0xFFFF /* DSP1RX_EQ_B5_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_PG_SHIFT 0 /* DSP1RX_EQ_B5_PG - [15:0] */
+#define WM8996_DSP1RX_EQ_B5_PG_WIDTH 16 /* DSP1RX_EQ_B5_PG - [15:0] */
+
+/*
+ * R1280 (0x500) - DSP2 TX Left Volume
+ */
+#define WM8996_DSP2TX_VU 0x0100 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_MASK 0x0100 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_SHIFT 8 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_WIDTH 1 /* DSP2TX_VU */
+#define WM8996_DSP2TXL_VOL_MASK 0x00FF /* DSP2TXL_VOL - [7:0] */
+#define WM8996_DSP2TXL_VOL_SHIFT 0 /* DSP2TXL_VOL - [7:0] */
+#define WM8996_DSP2TXL_VOL_WIDTH 8 /* DSP2TXL_VOL - [7:0] */
+
+/*
+ * R1281 (0x501) - DSP2 TX Right Volume
+ */
+#define WM8996_DSP2TX_VU 0x0100 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_MASK 0x0100 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_SHIFT 8 /* DSP2TX_VU */
+#define WM8996_DSP2TX_VU_WIDTH 1 /* DSP2TX_VU */
+#define WM8996_DSP2TXR_VOL_MASK 0x00FF /* DSP2TXR_VOL - [7:0] */
+#define WM8996_DSP2TXR_VOL_SHIFT 0 /* DSP2TXR_VOL - [7:0] */
+#define WM8996_DSP2TXR_VOL_WIDTH 8 /* DSP2TXR_VOL - [7:0] */
+
+/*
+ * R1282 (0x502) - DSP2 RX Left Volume
+ */
+#define WM8996_DSP2RX_VU 0x0100 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_MASK 0x0100 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_SHIFT 8 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_WIDTH 1 /* DSP2RX_VU */
+#define WM8996_DSP2RXL_VOL_MASK 0x00FF /* DSP2RXL_VOL - [7:0] */
+#define WM8996_DSP2RXL_VOL_SHIFT 0 /* DSP2RXL_VOL - [7:0] */
+#define WM8996_DSP2RXL_VOL_WIDTH 8 /* DSP2RXL_VOL - [7:0] */
+
+/*
+ * R1283 (0x503) - DSP2 RX Right Volume
+ */
+#define WM8996_DSP2RX_VU 0x0100 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_MASK 0x0100 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_SHIFT 8 /* DSP2RX_VU */
+#define WM8996_DSP2RX_VU_WIDTH 1 /* DSP2RX_VU */
+#define WM8996_DSP2RXR_VOL_MASK 0x00FF /* DSP2RXR_VOL - [7:0] */
+#define WM8996_DSP2RXR_VOL_SHIFT 0 /* DSP2RXR_VOL - [7:0] */
+#define WM8996_DSP2RXR_VOL_WIDTH 8 /* DSP2RXR_VOL - [7:0] */
+
+/*
+ * R1296 (0x510) - DSP2 TX Filters
+ */
+#define WM8996_DSP2TX_NF 0x2000 /* DSP2TX_NF */
+#define WM8996_DSP2TX_NF_MASK 0x2000 /* DSP2TX_NF */
+#define WM8996_DSP2TX_NF_SHIFT 13 /* DSP2TX_NF */
+#define WM8996_DSP2TX_NF_WIDTH 1 /* DSP2TX_NF */
+#define WM8996_DSP2TXL_HPF 0x1000 /* DSP2TXL_HPF */
+#define WM8996_DSP2TXL_HPF_MASK 0x1000 /* DSP2TXL_HPF */
+#define WM8996_DSP2TXL_HPF_SHIFT 12 /* DSP2TXL_HPF */
+#define WM8996_DSP2TXL_HPF_WIDTH 1 /* DSP2TXL_HPF */
+#define WM8996_DSP2TXR_HPF 0x0800 /* DSP2TXR_HPF */
+#define WM8996_DSP2TXR_HPF_MASK 0x0800 /* DSP2TXR_HPF */
+#define WM8996_DSP2TXR_HPF_SHIFT 11 /* DSP2TXR_HPF */
+#define WM8996_DSP2TXR_HPF_WIDTH 1 /* DSP2TXR_HPF */
+#define WM8996_DSP2TX_HPF_MODE_MASK 0x0018 /* DSP2TX_HPF_MODE - [4:3] */
+#define WM8996_DSP2TX_HPF_MODE_SHIFT 3 /* DSP2TX_HPF_MODE - [4:3] */
+#define WM8996_DSP2TX_HPF_MODE_WIDTH 2 /* DSP2TX_HPF_MODE - [4:3] */
+#define WM8996_DSP2TX_HPF_CUT_MASK 0x0007 /* DSP2TX_HPF_CUT - [2:0] */
+#define WM8996_DSP2TX_HPF_CUT_SHIFT 0 /* DSP2TX_HPF_CUT - [2:0] */
+#define WM8996_DSP2TX_HPF_CUT_WIDTH 3 /* DSP2TX_HPF_CUT - [2:0] */
+
+/*
+ * R1312 (0x520) - DSP2 RX Filters (1)
+ */
+#define WM8996_DSP2RX_MUTE 0x0200 /* DSP2RX_MUTE */
+#define WM8996_DSP2RX_MUTE_MASK 0x0200 /* DSP2RX_MUTE */
+#define WM8996_DSP2RX_MUTE_SHIFT 9 /* DSP2RX_MUTE */
+#define WM8996_DSP2RX_MUTE_WIDTH 1 /* DSP2RX_MUTE */
+#define WM8996_DSP2RX_MONO 0x0080 /* DSP2RX_MONO */
+#define WM8996_DSP2RX_MONO_MASK 0x0080 /* DSP2RX_MONO */
+#define WM8996_DSP2RX_MONO_SHIFT 7 /* DSP2RX_MONO */
+#define WM8996_DSP2RX_MONO_WIDTH 1 /* DSP2RX_MONO */
+#define WM8996_DSP2RX_MUTERATE 0x0020 /* DSP2RX_MUTERATE */
+#define WM8996_DSP2RX_MUTERATE_MASK 0x0020 /* DSP2RX_MUTERATE */
+#define WM8996_DSP2RX_MUTERATE_SHIFT 5 /* DSP2RX_MUTERATE */
+#define WM8996_DSP2RX_MUTERATE_WIDTH 1 /* DSP2RX_MUTERATE */
+#define WM8996_DSP2RX_UNMUTE_RAMP 0x0010 /* DSP2RX_UNMUTE_RAMP */
+#define WM8996_DSP2RX_UNMUTE_RAMP_MASK 0x0010 /* DSP2RX_UNMUTE_RAMP */
+#define WM8996_DSP2RX_UNMUTE_RAMP_SHIFT 4 /* DSP2RX_UNMUTE_RAMP */
+#define WM8996_DSP2RX_UNMUTE_RAMP_WIDTH 1 /* DSP2RX_UNMUTE_RAMP */
+
+/*
+ * R1313 (0x521) - DSP2 RX Filters (2)
+ */
+#define WM8996_DSP2RX_3D_GAIN_MASK 0x3E00 /* DSP2RX_3D_GAIN - [13:9] */
+#define WM8996_DSP2RX_3D_GAIN_SHIFT 9 /* DSP2RX_3D_GAIN - [13:9] */
+#define WM8996_DSP2RX_3D_GAIN_WIDTH 5 /* DSP2RX_3D_GAIN - [13:9] */
+#define WM8996_DSP2RX_3D_ENA 0x0100 /* DSP2RX_3D_ENA */
+#define WM8996_DSP2RX_3D_ENA_MASK 0x0100 /* DSP2RX_3D_ENA */
+#define WM8996_DSP2RX_3D_ENA_SHIFT 8 /* DSP2RX_3D_ENA */
+#define WM8996_DSP2RX_3D_ENA_WIDTH 1 /* DSP2RX_3D_ENA */
+
+/*
+ * R1344 (0x540) - DSP2 DRC (1)
+ */
+#define WM8996_DSP2DRC_SIG_DET_RMS_MASK 0xF800 /* DSP2DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP2DRC_SIG_DET_RMS_SHIFT 11 /* DSP2DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP2DRC_SIG_DET_RMS_WIDTH 5 /* DSP2DRC_SIG_DET_RMS - [15:11] */
+#define WM8996_DSP2DRC_SIG_DET_PK_MASK 0x0600 /* DSP2DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP2DRC_SIG_DET_PK_SHIFT 9 /* DSP2DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP2DRC_SIG_DET_PK_WIDTH 2 /* DSP2DRC_SIG_DET_PK - [10:9] */
+#define WM8996_DSP2DRC_NG_ENA 0x0100 /* DSP2DRC_NG_ENA */
+#define WM8996_DSP2DRC_NG_ENA_MASK 0x0100 /* DSP2DRC_NG_ENA */
+#define WM8996_DSP2DRC_NG_ENA_SHIFT 8 /* DSP2DRC_NG_ENA */
+#define WM8996_DSP2DRC_NG_ENA_WIDTH 1 /* DSP2DRC_NG_ENA */
+#define WM8996_DSP2DRC_SIG_DET_MODE 0x0080 /* DSP2DRC_SIG_DET_MODE */
+#define WM8996_DSP2DRC_SIG_DET_MODE_MASK 0x0080 /* DSP2DRC_SIG_DET_MODE */
+#define WM8996_DSP2DRC_SIG_DET_MODE_SHIFT 7 /* DSP2DRC_SIG_DET_MODE */
+#define WM8996_DSP2DRC_SIG_DET_MODE_WIDTH 1 /* DSP2DRC_SIG_DET_MODE */
+#define WM8996_DSP2DRC_SIG_DET 0x0040 /* DSP2DRC_SIG_DET */
+#define WM8996_DSP2DRC_SIG_DET_MASK 0x0040 /* DSP2DRC_SIG_DET */
+#define WM8996_DSP2DRC_SIG_DET_SHIFT 6 /* DSP2DRC_SIG_DET */
+#define WM8996_DSP2DRC_SIG_DET_WIDTH 1 /* DSP2DRC_SIG_DET */
+#define WM8996_DSP2DRC_KNEE2_OP_ENA 0x0020 /* DSP2DRC_KNEE2_OP_ENA */
+#define WM8996_DSP2DRC_KNEE2_OP_ENA_MASK 0x0020 /* DSP2DRC_KNEE2_OP_ENA */
+#define WM8996_DSP2DRC_KNEE2_OP_ENA_SHIFT 5 /* DSP2DRC_KNEE2_OP_ENA */
+#define WM8996_DSP2DRC_KNEE2_OP_ENA_WIDTH 1 /* DSP2DRC_KNEE2_OP_ENA */
+#define WM8996_DSP2DRC_QR 0x0010 /* DSP2DRC_QR */
+#define WM8996_DSP2DRC_QR_MASK 0x0010 /* DSP2DRC_QR */
+#define WM8996_DSP2DRC_QR_SHIFT 4 /* DSP2DRC_QR */
+#define WM8996_DSP2DRC_QR_WIDTH 1 /* DSP2DRC_QR */
+#define WM8996_DSP2DRC_ANTICLIP 0x0008 /* DSP2DRC_ANTICLIP */
+#define WM8996_DSP2DRC_ANTICLIP_MASK 0x0008 /* DSP2DRC_ANTICLIP */
+#define WM8996_DSP2DRC_ANTICLIP_SHIFT 3 /* DSP2DRC_ANTICLIP */
+#define WM8996_DSP2DRC_ANTICLIP_WIDTH 1 /* DSP2DRC_ANTICLIP */
+#define WM8996_DSP2RX_DRC_ENA 0x0004 /* DSP2RX_DRC_ENA */
+#define WM8996_DSP2RX_DRC_ENA_MASK 0x0004 /* DSP2RX_DRC_ENA */
+#define WM8996_DSP2RX_DRC_ENA_SHIFT 2 /* DSP2RX_DRC_ENA */
+#define WM8996_DSP2RX_DRC_ENA_WIDTH 1 /* DSP2RX_DRC_ENA */
+#define WM8996_DSP2TXL_DRC_ENA 0x0002 /* DSP2TXL_DRC_ENA */
+#define WM8996_DSP2TXL_DRC_ENA_MASK 0x0002 /* DSP2TXL_DRC_ENA */
+#define WM8996_DSP2TXL_DRC_ENA_SHIFT 1 /* DSP2TXL_DRC_ENA */
+#define WM8996_DSP2TXL_DRC_ENA_WIDTH 1 /* DSP2TXL_DRC_ENA */
+#define WM8996_DSP2TXR_DRC_ENA 0x0001 /* DSP2TXR_DRC_ENA */
+#define WM8996_DSP2TXR_DRC_ENA_MASK 0x0001 /* DSP2TXR_DRC_ENA */
+#define WM8996_DSP2TXR_DRC_ENA_SHIFT 0 /* DSP2TXR_DRC_ENA */
+#define WM8996_DSP2TXR_DRC_ENA_WIDTH 1 /* DSP2TXR_DRC_ENA */
+
+/*
+ * R1345 (0x541) - DSP2 DRC (2)
+ */
+#define WM8996_DSP2DRC_ATK_MASK 0x1E00 /* DSP2DRC_ATK - [12:9] */
+#define WM8996_DSP2DRC_ATK_SHIFT 9 /* DSP2DRC_ATK - [12:9] */
+#define WM8996_DSP2DRC_ATK_WIDTH 4 /* DSP2DRC_ATK - [12:9] */
+#define WM8996_DSP2DRC_DCY_MASK 0x01E0 /* DSP2DRC_DCY - [8:5] */
+#define WM8996_DSP2DRC_DCY_SHIFT 5 /* DSP2DRC_DCY - [8:5] */
+#define WM8996_DSP2DRC_DCY_WIDTH 4 /* DSP2DRC_DCY - [8:5] */
+#define WM8996_DSP2DRC_MINGAIN_MASK 0x001C /* DSP2DRC_MINGAIN - [4:2] */
+#define WM8996_DSP2DRC_MINGAIN_SHIFT 2 /* DSP2DRC_MINGAIN - [4:2] */
+#define WM8996_DSP2DRC_MINGAIN_WIDTH 3 /* DSP2DRC_MINGAIN - [4:2] */
+#define WM8996_DSP2DRC_MAXGAIN_MASK 0x0003 /* DSP2DRC_MAXGAIN - [1:0] */
+#define WM8996_DSP2DRC_MAXGAIN_SHIFT 0 /* DSP2DRC_MAXGAIN - [1:0] */
+#define WM8996_DSP2DRC_MAXGAIN_WIDTH 2 /* DSP2DRC_MAXGAIN - [1:0] */
+
+/*
+ * R1346 (0x542) - DSP2 DRC (3)
+ */
+#define WM8996_DSP2DRC_NG_MINGAIN_MASK 0xF000 /* DSP2DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP2DRC_NG_MINGAIN_SHIFT 12 /* DSP2DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP2DRC_NG_MINGAIN_WIDTH 4 /* DSP2DRC_NG_MINGAIN - [15:12] */
+#define WM8996_DSP2DRC_NG_EXP_MASK 0x0C00 /* DSP2DRC_NG_EXP - [11:10] */
+#define WM8996_DSP2DRC_NG_EXP_SHIFT 10 /* DSP2DRC_NG_EXP - [11:10] */
+#define WM8996_DSP2DRC_NG_EXP_WIDTH 2 /* DSP2DRC_NG_EXP - [11:10] */
+#define WM8996_DSP2DRC_QR_THR_MASK 0x0300 /* DSP2DRC_QR_THR - [9:8] */
+#define WM8996_DSP2DRC_QR_THR_SHIFT 8 /* DSP2DRC_QR_THR - [9:8] */
+#define WM8996_DSP2DRC_QR_THR_WIDTH 2 /* DSP2DRC_QR_THR - [9:8] */
+#define WM8996_DSP2DRC_QR_DCY_MASK 0x00C0 /* DSP2DRC_QR_DCY - [7:6] */
+#define WM8996_DSP2DRC_QR_DCY_SHIFT 6 /* DSP2DRC_QR_DCY - [7:6] */
+#define WM8996_DSP2DRC_QR_DCY_WIDTH 2 /* DSP2DRC_QR_DCY - [7:6] */
+#define WM8996_DSP2DRC_HI_COMP_MASK 0x0038 /* DSP2DRC_HI_COMP - [5:3] */
+#define WM8996_DSP2DRC_HI_COMP_SHIFT 3 /* DSP2DRC_HI_COMP - [5:3] */
+#define WM8996_DSP2DRC_HI_COMP_WIDTH 3 /* DSP2DRC_HI_COMP - [5:3] */
+#define WM8996_DSP2DRC_LO_COMP_MASK 0x0007 /* DSP2DRC_LO_COMP - [2:0] */
+#define WM8996_DSP2DRC_LO_COMP_SHIFT 0 /* DSP2DRC_LO_COMP - [2:0] */
+#define WM8996_DSP2DRC_LO_COMP_WIDTH 3 /* DSP2DRC_LO_COMP - [2:0] */
+
+/*
+ * R1347 (0x543) - DSP2 DRC (4)
+ */
+#define WM8996_DSP2DRC_KNEE_IP_MASK 0x07E0 /* DSP2DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP2DRC_KNEE_IP_SHIFT 5 /* DSP2DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP2DRC_KNEE_IP_WIDTH 6 /* DSP2DRC_KNEE_IP - [10:5] */
+#define WM8996_DSP2DRC_KNEE_OP_MASK 0x001F /* DSP2DRC_KNEE_OP - [4:0] */
+#define WM8996_DSP2DRC_KNEE_OP_SHIFT 0 /* DSP2DRC_KNEE_OP - [4:0] */
+#define WM8996_DSP2DRC_KNEE_OP_WIDTH 5 /* DSP2DRC_KNEE_OP - [4:0] */
+
+/*
+ * R1348 (0x544) - DSP2 DRC (5)
+ */
+#define WM8996_DSP2DRC_KNEE2_IP_MASK 0x03E0 /* DSP2DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP2DRC_KNEE2_IP_SHIFT 5 /* DSP2DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP2DRC_KNEE2_IP_WIDTH 5 /* DSP2DRC_KNEE2_IP - [9:5] */
+#define WM8996_DSP2DRC_KNEE2_OP_MASK 0x001F /* DSP2DRC_KNEE2_OP - [4:0] */
+#define WM8996_DSP2DRC_KNEE2_OP_SHIFT 0 /* DSP2DRC_KNEE2_OP - [4:0] */
+#define WM8996_DSP2DRC_KNEE2_OP_WIDTH 5 /* DSP2DRC_KNEE2_OP - [4:0] */
+
+/*
+ * R1408 (0x580) - DSP2 RX EQ Gains (1)
+ */
+#define WM8996_DSP2RX_EQ_B1_GAIN_MASK 0xF800 /* DSP2RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B1_GAIN_SHIFT 11 /* DSP2RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B1_GAIN_WIDTH 5 /* DSP2RX_EQ_B1_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B2_GAIN_MASK 0x07C0 /* DSP2RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP2RX_EQ_B2_GAIN_SHIFT 6 /* DSP2RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP2RX_EQ_B2_GAIN_WIDTH 5 /* DSP2RX_EQ_B2_GAIN - [10:6] */
+#define WM8996_DSP2RX_EQ_B3_GAIN_MASK 0x003E /* DSP2RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP2RX_EQ_B3_GAIN_SHIFT 1 /* DSP2RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP2RX_EQ_B3_GAIN_WIDTH 5 /* DSP2RX_EQ_B3_GAIN - [5:1] */
+#define WM8996_DSP2RX_EQ_ENA 0x0001 /* DSP2RX_EQ_ENA */
+#define WM8996_DSP2RX_EQ_ENA_MASK 0x0001 /* DSP2RX_EQ_ENA */
+#define WM8996_DSP2RX_EQ_ENA_SHIFT 0 /* DSP2RX_EQ_ENA */
+#define WM8996_DSP2RX_EQ_ENA_WIDTH 1 /* DSP2RX_EQ_ENA */
+
+/*
+ * R1409 (0x581) - DSP2 RX EQ Gains (2)
+ */
+#define WM8996_DSP2RX_EQ_B4_GAIN_MASK 0xF800 /* DSP2RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B4_GAIN_SHIFT 11 /* DSP2RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B4_GAIN_WIDTH 5 /* DSP2RX_EQ_B4_GAIN - [15:11] */
+#define WM8996_DSP2RX_EQ_B5_GAIN_MASK 0x07C0 /* DSP2RX_EQ_B5_GAIN - [10:6] */
+#define WM8996_DSP2RX_EQ_B5_GAIN_SHIFT 6 /* DSP2RX_EQ_B5_GAIN - [10:6] */
+#define WM8996_DSP2RX_EQ_B5_GAIN_WIDTH 5 /* DSP2RX_EQ_B5_GAIN - [10:6] */
+
+/*
+ * R1410 (0x582) - DSP2 RX EQ Band 1 A
+ */
+#define WM8996_DSP2RX_EQ_B1_A_MASK 0xFFFF /* DSP2RX_EQ_B1_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_A_SHIFT 0 /* DSP2RX_EQ_B1_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_A_WIDTH 16 /* DSP2RX_EQ_B1_A - [15:0] */
+
+/*
+ * R1411 (0x583) - DSP2 RX EQ Band 1 B
+ */
+#define WM8996_DSP2RX_EQ_B1_B_MASK 0xFFFF /* DSP2RX_EQ_B1_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_B_SHIFT 0 /* DSP2RX_EQ_B1_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_B_WIDTH 16 /* DSP2RX_EQ_B1_B - [15:0] */
+
+/*
+ * R1412 (0x584) - DSP2 RX EQ Band 1 PG
+ */
+#define WM8996_DSP2RX_EQ_B1_PG_MASK 0xFFFF /* DSP2RX_EQ_B1_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_PG_SHIFT 0 /* DSP2RX_EQ_B1_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B1_PG_WIDTH 16 /* DSP2RX_EQ_B1_PG - [15:0] */
+
+/*
+ * R1413 (0x585) - DSP2 RX EQ Band 2 A
+ */
+#define WM8996_DSP2RX_EQ_B2_A_MASK 0xFFFF /* DSP2RX_EQ_B2_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_A_SHIFT 0 /* DSP2RX_EQ_B2_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_A_WIDTH 16 /* DSP2RX_EQ_B2_A - [15:0] */
+
+/*
+ * R1414 (0x586) - DSP2 RX EQ Band 2 B
+ */
+#define WM8996_DSP2RX_EQ_B2_B_MASK 0xFFFF /* DSP2RX_EQ_B2_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_B_SHIFT 0 /* DSP2RX_EQ_B2_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_B_WIDTH 16 /* DSP2RX_EQ_B2_B - [15:0] */
+
+/*
+ * R1415 (0x587) - DSP2 RX EQ Band 2 C
+ */
+#define WM8996_DSP2RX_EQ_B2_C_MASK 0xFFFF /* DSP2RX_EQ_B2_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_C_SHIFT 0 /* DSP2RX_EQ_B2_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_C_WIDTH 16 /* DSP2RX_EQ_B2_C - [15:0] */
+
+/*
+ * R1416 (0x588) - DSP2 RX EQ Band 2 PG
+ */
+#define WM8996_DSP2RX_EQ_B2_PG_MASK 0xFFFF /* DSP2RX_EQ_B2_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_PG_SHIFT 0 /* DSP2RX_EQ_B2_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B2_PG_WIDTH 16 /* DSP2RX_EQ_B2_PG - [15:0] */
+
+/*
+ * R1417 (0x589) - DSP2 RX EQ Band 3 A
+ */
+#define WM8996_DSP2RX_EQ_B3_A_MASK 0xFFFF /* DSP2RX_EQ_B3_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_A_SHIFT 0 /* DSP2RX_EQ_B3_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_A_WIDTH 16 /* DSP2RX_EQ_B3_A - [15:0] */
+
+/*
+ * R1418 (0x58A) - DSP2 RX EQ Band 3 B
+ */
+#define WM8996_DSP2RX_EQ_B3_B_MASK 0xFFFF /* DSP2RX_EQ_B3_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_B_SHIFT 0 /* DSP2RX_EQ_B3_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_B_WIDTH 16 /* DSP2RX_EQ_B3_B - [15:0] */
+
+/*
+ * R1419 (0x58B) - DSP2 RX EQ Band 3 C
+ */
+#define WM8996_DSP2RX_EQ_B3_C_MASK 0xFFFF /* DSP2RX_EQ_B3_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_C_SHIFT 0 /* DSP2RX_EQ_B3_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_C_WIDTH 16 /* DSP2RX_EQ_B3_C - [15:0] */
+
+/*
+ * R1420 (0x58C) - DSP2 RX EQ Band 3 PG
+ */
+#define WM8996_DSP2RX_EQ_B3_PG_MASK 0xFFFF /* DSP2RX_EQ_B3_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_PG_SHIFT 0 /* DSP2RX_EQ_B3_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B3_PG_WIDTH 16 /* DSP2RX_EQ_B3_PG - [15:0] */
+
+/*
+ * R1421 (0x58D) - DSP2 RX EQ Band 4 A
+ */
+#define WM8996_DSP2RX_EQ_B4_A_MASK 0xFFFF /* DSP2RX_EQ_B4_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_A_SHIFT 0 /* DSP2RX_EQ_B4_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_A_WIDTH 16 /* DSP2RX_EQ_B4_A - [15:0] */
+
+/*
+ * R1422 (0x58E) - DSP2 RX EQ Band 4 B
+ */
+#define WM8996_DSP2RX_EQ_B4_B_MASK 0xFFFF /* DSP2RX_EQ_B4_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_B_SHIFT 0 /* DSP2RX_EQ_B4_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_B_WIDTH 16 /* DSP2RX_EQ_B4_B - [15:0] */
+
+/*
+ * R1423 (0x58F) - DSP2 RX EQ Band 4 C
+ */
+#define WM8996_DSP2RX_EQ_B4_C_MASK 0xFFFF /* DSP2RX_EQ_B4_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_C_SHIFT 0 /* DSP2RX_EQ_B4_C - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_C_WIDTH 16 /* DSP2RX_EQ_B4_C - [15:0] */
+
+/*
+ * R1424 (0x590) - DSP2 RX EQ Band 4 PG
+ */
+#define WM8996_DSP2RX_EQ_B4_PG_MASK 0xFFFF /* DSP2RX_EQ_B4_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_PG_SHIFT 0 /* DSP2RX_EQ_B4_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B4_PG_WIDTH 16 /* DSP2RX_EQ_B4_PG - [15:0] */
+
+/*
+ * R1425 (0x591) - DSP2 RX EQ Band 5 A
+ */
+#define WM8996_DSP2RX_EQ_B5_A_MASK 0xFFFF /* DSP2RX_EQ_B5_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_A_SHIFT 0 /* DSP2RX_EQ_B5_A - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_A_WIDTH 16 /* DSP2RX_EQ_B5_A - [15:0] */
+
+/*
+ * R1426 (0x592) - DSP2 RX EQ Band 5 B
+ */
+#define WM8996_DSP2RX_EQ_B5_B_MASK 0xFFFF /* DSP2RX_EQ_B5_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_B_SHIFT 0 /* DSP2RX_EQ_B5_B - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_B_WIDTH 16 /* DSP2RX_EQ_B5_B - [15:0] */
+
+/*
+ * R1427 (0x593) - DSP2 RX EQ Band 5 PG
+ */
+#define WM8996_DSP2RX_EQ_B5_PG_MASK 0xFFFF /* DSP2RX_EQ_B5_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_PG_SHIFT 0 /* DSP2RX_EQ_B5_PG - [15:0] */
+#define WM8996_DSP2RX_EQ_B5_PG_WIDTH 16 /* DSP2RX_EQ_B5_PG - [15:0] */
+
+/*
+ * R1536 (0x600) - DAC1 Mixer Volumes
+ */
+#define WM8996_ADCR_DAC1_VOL_MASK 0x03E0 /* ADCR_DAC1_VOL - [9:5] */
+#define WM8996_ADCR_DAC1_VOL_SHIFT 5 /* ADCR_DAC1_VOL - [9:5] */
+#define WM8996_ADCR_DAC1_VOL_WIDTH 5 /* ADCR_DAC1_VOL - [9:5] */
+#define WM8996_ADCL_DAC1_VOL_MASK 0x001F /* ADCL_DAC1_VOL - [4:0] */
+#define WM8996_ADCL_DAC1_VOL_SHIFT 0 /* ADCL_DAC1_VOL - [4:0] */
+#define WM8996_ADCL_DAC1_VOL_WIDTH 5 /* ADCL_DAC1_VOL - [4:0] */
+
+/*
+ * R1537 (0x601) - DAC1 Left Mixer Routing
+ */
+#define WM8996_ADCR_TO_DAC1L 0x0020 /* ADCR_TO_DAC1L */
+#define WM8996_ADCR_TO_DAC1L_MASK 0x0020 /* ADCR_TO_DAC1L */
+#define WM8996_ADCR_TO_DAC1L_SHIFT 5 /* ADCR_TO_DAC1L */
+#define WM8996_ADCR_TO_DAC1L_WIDTH 1 /* ADCR_TO_DAC1L */
+#define WM8996_ADCL_TO_DAC1L 0x0010 /* ADCL_TO_DAC1L */
+#define WM8996_ADCL_TO_DAC1L_MASK 0x0010 /* ADCL_TO_DAC1L */
+#define WM8996_ADCL_TO_DAC1L_SHIFT 4 /* ADCL_TO_DAC1L */
+#define WM8996_ADCL_TO_DAC1L_WIDTH 1 /* ADCL_TO_DAC1L */
+#define WM8996_DSP2RXL_TO_DAC1L 0x0002 /* DSP2RXL_TO_DAC1L */
+#define WM8996_DSP2RXL_TO_DAC1L_MASK 0x0002 /* DSP2RXL_TO_DAC1L */
+#define WM8996_DSP2RXL_TO_DAC1L_SHIFT 1 /* DSP2RXL_TO_DAC1L */
+#define WM8996_DSP2RXL_TO_DAC1L_WIDTH 1 /* DSP2RXL_TO_DAC1L */
+#define WM8996_DSP1RXL_TO_DAC1L 0x0001 /* DSP1RXL_TO_DAC1L */
+#define WM8996_DSP1RXL_TO_DAC1L_MASK 0x0001 /* DSP1RXL_TO_DAC1L */
+#define WM8996_DSP1RXL_TO_DAC1L_SHIFT 0 /* DSP1RXL_TO_DAC1L */
+#define WM8996_DSP1RXL_TO_DAC1L_WIDTH 1 /* DSP1RXL_TO_DAC1L */
+
+/*
+ * R1538 (0x602) - DAC1 Right Mixer Routing
+ */
+#define WM8996_ADCR_TO_DAC1R 0x0020 /* ADCR_TO_DAC1R */
+#define WM8996_ADCR_TO_DAC1R_MASK 0x0020 /* ADCR_TO_DAC1R */
+#define WM8996_ADCR_TO_DAC1R_SHIFT 5 /* ADCR_TO_DAC1R */
+#define WM8996_ADCR_TO_DAC1R_WIDTH 1 /* ADCR_TO_DAC1R */
+#define WM8996_ADCL_TO_DAC1R 0x0010 /* ADCL_TO_DAC1R */
+#define WM8996_ADCL_TO_DAC1R_MASK 0x0010 /* ADCL_TO_DAC1R */
+#define WM8996_ADCL_TO_DAC1R_SHIFT 4 /* ADCL_TO_DAC1R */
+#define WM8996_ADCL_TO_DAC1R_WIDTH 1 /* ADCL_TO_DAC1R */
+#define WM8996_DSP2RXR_TO_DAC1R 0x0002 /* DSP2RXR_TO_DAC1R */
+#define WM8996_DSP2RXR_TO_DAC1R_MASK 0x0002 /* DSP2RXR_TO_DAC1R */
+#define WM8996_DSP2RXR_TO_DAC1R_SHIFT 1 /* DSP2RXR_TO_DAC1R */
+#define WM8996_DSP2RXR_TO_DAC1R_WIDTH 1 /* DSP2RXR_TO_DAC1R */
+#define WM8996_DSP1RXR_TO_DAC1R 0x0001 /* DSP1RXR_TO_DAC1R */
+#define WM8996_DSP1RXR_TO_DAC1R_MASK 0x0001 /* DSP1RXR_TO_DAC1R */
+#define WM8996_DSP1RXR_TO_DAC1R_SHIFT 0 /* DSP1RXR_TO_DAC1R */
+#define WM8996_DSP1RXR_TO_DAC1R_WIDTH 1 /* DSP1RXR_TO_DAC1R */
+
+/*
+ * R1539 (0x603) - DAC2 Mixer Volumes
+ */
+#define WM8996_ADCR_DAC2_VOL_MASK 0x03E0 /* ADCR_DAC2_VOL - [9:5] */
+#define WM8996_ADCR_DAC2_VOL_SHIFT 5 /* ADCR_DAC2_VOL - [9:5] */
+#define WM8996_ADCR_DAC2_VOL_WIDTH 5 /* ADCR_DAC2_VOL - [9:5] */
+#define WM8996_ADCL_DAC2_VOL_MASK 0x001F /* ADCL_DAC2_VOL - [4:0] */
+#define WM8996_ADCL_DAC2_VOL_SHIFT 0 /* ADCL_DAC2_VOL - [4:0] */
+#define WM8996_ADCL_DAC2_VOL_WIDTH 5 /* ADCL_DAC2_VOL - [4:0] */
+
+/*
+ * R1540 (0x604) - DAC2 Left Mixer Routing
+ */
+#define WM8996_ADCR_TO_DAC2L 0x0020 /* ADCR_TO_DAC2L */
+#define WM8996_ADCR_TO_DAC2L_MASK 0x0020 /* ADCR_TO_DAC2L */
+#define WM8996_ADCR_TO_DAC2L_SHIFT 5 /* ADCR_TO_DAC2L */
+#define WM8996_ADCR_TO_DAC2L_WIDTH 1 /* ADCR_TO_DAC2L */
+#define WM8996_ADCL_TO_DAC2L 0x0010 /* ADCL_TO_DAC2L */
+#define WM8996_ADCL_TO_DAC2L_MASK 0x0010 /* ADCL_TO_DAC2L */
+#define WM8996_ADCL_TO_DAC2L_SHIFT 4 /* ADCL_TO_DAC2L */
+#define WM8996_ADCL_TO_DAC2L_WIDTH 1 /* ADCL_TO_DAC2L */
+#define WM8996_DSP2RXL_TO_DAC2L 0x0002 /* DSP2RXL_TO_DAC2L */
+#define WM8996_DSP2RXL_TO_DAC2L_MASK 0x0002 /* DSP2RXL_TO_DAC2L */
+#define WM8996_DSP2RXL_TO_DAC2L_SHIFT 1 /* DSP2RXL_TO_DAC2L */
+#define WM8996_DSP2RXL_TO_DAC2L_WIDTH 1 /* DSP2RXL_TO_DAC2L */
+#define WM8996_DSP1RXL_TO_DAC2L 0x0001 /* DSP1RXL_TO_DAC2L */
+#define WM8996_DSP1RXL_TO_DAC2L_MASK 0x0001 /* DSP1RXL_TO_DAC2L */
+#define WM8996_DSP1RXL_TO_DAC2L_SHIFT 0 /* DSP1RXL_TO_DAC2L */
+#define WM8996_DSP1RXL_TO_DAC2L_WIDTH 1 /* DSP1RXL_TO_DAC2L */
+
+/*
+ * R1541 (0x605) - DAC2 Right Mixer Routing
+ */
+#define WM8996_ADCR_TO_DAC2R 0x0020 /* ADCR_TO_DAC2R */
+#define WM8996_ADCR_TO_DAC2R_MASK 0x0020 /* ADCR_TO_DAC2R */
+#define WM8996_ADCR_TO_DAC2R_SHIFT 5 /* ADCR_TO_DAC2R */
+#define WM8996_ADCR_TO_DAC2R_WIDTH 1 /* ADCR_TO_DAC2R */
+#define WM8996_ADCL_TO_DAC2R 0x0010 /* ADCL_TO_DAC2R */
+#define WM8996_ADCL_TO_DAC2R_MASK 0x0010 /* ADCL_TO_DAC2R */
+#define WM8996_ADCL_TO_DAC2R_SHIFT 4 /* ADCL_TO_DAC2R */
+#define WM8996_ADCL_TO_DAC2R_WIDTH 1 /* ADCL_TO_DAC2R */
+#define WM8996_DSP2RXR_TO_DAC2R 0x0002 /* DSP2RXR_TO_DAC2R */
+#define WM8996_DSP2RXR_TO_DAC2R_MASK 0x0002 /* DSP2RXR_TO_DAC2R */
+#define WM8996_DSP2RXR_TO_DAC2R_SHIFT 1 /* DSP2RXR_TO_DAC2R */
+#define WM8996_DSP2RXR_TO_DAC2R_WIDTH 1 /* DSP2RXR_TO_DAC2R */
+#define WM8996_DSP1RXR_TO_DAC2R 0x0001 /* DSP1RXR_TO_DAC2R */
+#define WM8996_DSP1RXR_TO_DAC2R_MASK 0x0001 /* DSP1RXR_TO_DAC2R */
+#define WM8996_DSP1RXR_TO_DAC2R_SHIFT 0 /* DSP1RXR_TO_DAC2R */
+#define WM8996_DSP1RXR_TO_DAC2R_WIDTH 1 /* DSP1RXR_TO_DAC2R */
+
+/*
+ * R1542 (0x606) - DSP1 TX Left Mixer Routing
+ */
+#define WM8996_ADC1L_TO_DSP1TXL 0x0002 /* ADC1L_TO_DSP1TXL */
+#define WM8996_ADC1L_TO_DSP1TXL_MASK 0x0002 /* ADC1L_TO_DSP1TXL */
+#define WM8996_ADC1L_TO_DSP1TXL_SHIFT 1 /* ADC1L_TO_DSP1TXL */
+#define WM8996_ADC1L_TO_DSP1TXL_WIDTH 1 /* ADC1L_TO_DSP1TXL */
+#define WM8996_DACL_TO_DSP1TXL 0x0001 /* DACL_TO_DSP1TXL */
+#define WM8996_DACL_TO_DSP1TXL_MASK 0x0001 /* DACL_TO_DSP1TXL */
+#define WM8996_DACL_TO_DSP1TXL_SHIFT 0 /* DACL_TO_DSP1TXL */
+#define WM8996_DACL_TO_DSP1TXL_WIDTH 1 /* DACL_TO_DSP1TXL */
+
+/*
+ * R1543 (0x607) - DSP1 TX Right Mixer Routing
+ */
+#define WM8996_ADC1R_TO_DSP1TXR 0x0002 /* ADC1R_TO_DSP1TXR */
+#define WM8996_ADC1R_TO_DSP1TXR_MASK 0x0002 /* ADC1R_TO_DSP1TXR */
+#define WM8996_ADC1R_TO_DSP1TXR_SHIFT 1 /* ADC1R_TO_DSP1TXR */
+#define WM8996_ADC1R_TO_DSP1TXR_WIDTH 1 /* ADC1R_TO_DSP1TXR */
+#define WM8996_DACR_TO_DSP1TXR 0x0001 /* DACR_TO_DSP1TXR */
+#define WM8996_DACR_TO_DSP1TXR_MASK 0x0001 /* DACR_TO_DSP1TXR */
+#define WM8996_DACR_TO_DSP1TXR_SHIFT 0 /* DACR_TO_DSP1TXR */
+#define WM8996_DACR_TO_DSP1TXR_WIDTH 1 /* DACR_TO_DSP1TXR */
+
+/*
+ * R1544 (0x608) - DSP2 TX Left Mixer Routing
+ */
+#define WM8996_ADC2L_TO_DSP2TXL 0x0002 /* ADC2L_TO_DSP2TXL */
+#define WM8996_ADC2L_TO_DSP2TXL_MASK 0x0002 /* ADC2L_TO_DSP2TXL */
+#define WM8996_ADC2L_TO_DSP2TXL_SHIFT 1 /* ADC2L_TO_DSP2TXL */
+#define WM8996_ADC2L_TO_DSP2TXL_WIDTH 1 /* ADC2L_TO_DSP2TXL */
+#define WM8996_DACL_TO_DSP2TXL 0x0001 /* DACL_TO_DSP2TXL */
+#define WM8996_DACL_TO_DSP2TXL_MASK 0x0001 /* DACL_TO_DSP2TXL */
+#define WM8996_DACL_TO_DSP2TXL_SHIFT 0 /* DACL_TO_DSP2TXL */
+#define WM8996_DACL_TO_DSP2TXL_WIDTH 1 /* DACL_TO_DSP2TXL */
+
+/*
+ * R1545 (0x609) - DSP2 TX Right Mixer Routing
+ */
+#define WM8996_ADC2R_TO_DSP2TXR 0x0002 /* ADC2R_TO_DSP2TXR */
+#define WM8996_ADC2R_TO_DSP2TXR_MASK 0x0002 /* ADC2R_TO_DSP2TXR */
+#define WM8996_ADC2R_TO_DSP2TXR_SHIFT 1 /* ADC2R_TO_DSP2TXR */
+#define WM8996_ADC2R_TO_DSP2TXR_WIDTH 1 /* ADC2R_TO_DSP2TXR */
+#define WM8996_DACR_TO_DSP2TXR 0x0001 /* DACR_TO_DSP2TXR */
+#define WM8996_DACR_TO_DSP2TXR_MASK 0x0001 /* DACR_TO_DSP2TXR */
+#define WM8996_DACR_TO_DSP2TXR_SHIFT 0 /* DACR_TO_DSP2TXR */
+#define WM8996_DACR_TO_DSP2TXR_WIDTH 1 /* DACR_TO_DSP2TXR */
+
+/*
+ * R1546 (0x60A) - DSP TX Mixer Select
+ */
+#define WM8996_DAC_TO_DSPTX_SRC 0x0001 /* DAC_TO_DSPTX_SRC */
+#define WM8996_DAC_TO_DSPTX_SRC_MASK 0x0001 /* DAC_TO_DSPTX_SRC */
+#define WM8996_DAC_TO_DSPTX_SRC_SHIFT 0 /* DAC_TO_DSPTX_SRC */
+#define WM8996_DAC_TO_DSPTX_SRC_WIDTH 1 /* DAC_TO_DSPTX_SRC */
+
+/*
+ * R1552 (0x610) - DAC Softmute
+ */
+#define WM8996_DAC_SOFTMUTEMODE 0x0002 /* DAC_SOFTMUTEMODE */
+#define WM8996_DAC_SOFTMUTEMODE_MASK 0x0002 /* DAC_SOFTMUTEMODE */
+#define WM8996_DAC_SOFTMUTEMODE_SHIFT 1 /* DAC_SOFTMUTEMODE */
+#define WM8996_DAC_SOFTMUTEMODE_WIDTH 1 /* DAC_SOFTMUTEMODE */
+#define WM8996_DAC_MUTERATE 0x0001 /* DAC_MUTERATE */
+#define WM8996_DAC_MUTERATE_MASK 0x0001 /* DAC_MUTERATE */
+#define WM8996_DAC_MUTERATE_SHIFT 0 /* DAC_MUTERATE */
+#define WM8996_DAC_MUTERATE_WIDTH 1 /* DAC_MUTERATE */
+
+/*
+ * R1568 (0x620) - Oversampling
+ */
+#define WM8996_SPK_OSR128 0x0008 /* SPK_OSR128 */
+#define WM8996_SPK_OSR128_MASK 0x0008 /* SPK_OSR128 */
+#define WM8996_SPK_OSR128_SHIFT 3 /* SPK_OSR128 */
+#define WM8996_SPK_OSR128_WIDTH 1 /* SPK_OSR128 */
+#define WM8996_DMIC_OSR64 0x0004 /* DMIC_OSR64 */
+#define WM8996_DMIC_OSR64_MASK 0x0004 /* DMIC_OSR64 */
+#define WM8996_DMIC_OSR64_SHIFT 2 /* DMIC_OSR64 */
+#define WM8996_DMIC_OSR64_WIDTH 1 /* DMIC_OSR64 */
+#define WM8996_ADC_OSR128 0x0002 /* ADC_OSR128 */
+#define WM8996_ADC_OSR128_MASK 0x0002 /* ADC_OSR128 */
+#define WM8996_ADC_OSR128_SHIFT 1 /* ADC_OSR128 */
+#define WM8996_ADC_OSR128_WIDTH 1 /* ADC_OSR128 */
+#define WM8996_DAC_OSR128 0x0001 /* DAC_OSR128 */
+#define WM8996_DAC_OSR128_MASK 0x0001 /* DAC_OSR128 */
+#define WM8996_DAC_OSR128_SHIFT 0 /* DAC_OSR128 */
+#define WM8996_DAC_OSR128_WIDTH 1 /* DAC_OSR128 */
+
+/*
+ * R1569 (0x621) - Sidetone
+ */
+#define WM8996_ST_LPF 0x1000 /* ST_LPF */
+#define WM8996_ST_LPF_MASK 0x1000 /* ST_LPF */
+#define WM8996_ST_LPF_SHIFT 12 /* ST_LPF */
+#define WM8996_ST_LPF_WIDTH 1 /* ST_LPF */
+#define WM8996_ST_HPF_CUT_MASK 0x0380 /* ST_HPF_CUT - [9:7] */
+#define WM8996_ST_HPF_CUT_SHIFT 7 /* ST_HPF_CUT - [9:7] */
+#define WM8996_ST_HPF_CUT_WIDTH 3 /* ST_HPF_CUT - [9:7] */
+#define WM8996_ST_HPF 0x0040 /* ST_HPF */
+#define WM8996_ST_HPF_MASK 0x0040 /* ST_HPF */
+#define WM8996_ST_HPF_SHIFT 6 /* ST_HPF */
+#define WM8996_ST_HPF_WIDTH 1 /* ST_HPF */
+#define WM8996_STR_SEL 0x0002 /* STR_SEL */
+#define WM8996_STR_SEL_MASK 0x0002 /* STR_SEL */
+#define WM8996_STR_SEL_SHIFT 1 /* STR_SEL */
+#define WM8996_STR_SEL_WIDTH 1 /* STR_SEL */
+#define WM8996_STL_SEL 0x0001 /* STL_SEL */
+#define WM8996_STL_SEL_MASK 0x0001 /* STL_SEL */
+#define WM8996_STL_SEL_SHIFT 0 /* STL_SEL */
+#define WM8996_STL_SEL_WIDTH 1 /* STL_SEL */
+
+/*
+ * R1792 (0x700) - GPIO 1
+ */
+#define WM8996_GP1_DIR 0x8000 /* GP1_DIR */
+#define WM8996_GP1_DIR_MASK 0x8000 /* GP1_DIR */
+#define WM8996_GP1_DIR_SHIFT 15 /* GP1_DIR */
+#define WM8996_GP1_DIR_WIDTH 1 /* GP1_DIR */
+#define WM8996_GP1_PU 0x4000 /* GP1_PU */
+#define WM8996_GP1_PU_MASK 0x4000 /* GP1_PU */
+#define WM8996_GP1_PU_SHIFT 14 /* GP1_PU */
+#define WM8996_GP1_PU_WIDTH 1 /* GP1_PU */
+#define WM8996_GP1_PD 0x2000 /* GP1_PD */
+#define WM8996_GP1_PD_MASK 0x2000 /* GP1_PD */
+#define WM8996_GP1_PD_SHIFT 13 /* GP1_PD */
+#define WM8996_GP1_PD_WIDTH 1 /* GP1_PD */
+#define WM8996_GP1_POL 0x0400 /* GP1_POL */
+#define WM8996_GP1_POL_MASK 0x0400 /* GP1_POL */
+#define WM8996_GP1_POL_SHIFT 10 /* GP1_POL */
+#define WM8996_GP1_POL_WIDTH 1 /* GP1_POL */
+#define WM8996_GP1_OP_CFG 0x0200 /* GP1_OP_CFG */
+#define WM8996_GP1_OP_CFG_MASK 0x0200 /* GP1_OP_CFG */
+#define WM8996_GP1_OP_CFG_SHIFT 9 /* GP1_OP_CFG */
+#define WM8996_GP1_OP_CFG_WIDTH 1 /* GP1_OP_CFG */
+#define WM8996_GP1_DB 0x0100 /* GP1_DB */
+#define WM8996_GP1_DB_MASK 0x0100 /* GP1_DB */
+#define WM8996_GP1_DB_SHIFT 8 /* GP1_DB */
+#define WM8996_GP1_DB_WIDTH 1 /* GP1_DB */
+#define WM8996_GP1_LVL 0x0040 /* GP1_LVL */
+#define WM8996_GP1_LVL_MASK 0x0040 /* GP1_LVL */
+#define WM8996_GP1_LVL_SHIFT 6 /* GP1_LVL */
+#define WM8996_GP1_LVL_WIDTH 1 /* GP1_LVL */
+#define WM8996_GP1_FN_MASK 0x000F /* GP1_FN - [3:0] */
+#define WM8996_GP1_FN_SHIFT 0 /* GP1_FN - [3:0] */
+#define WM8996_GP1_FN_WIDTH 4 /* GP1_FN - [3:0] */
+
+/*
+ * R1793 (0x701) - GPIO 2
+ */
+#define WM8996_GP2_DIR 0x8000 /* GP2_DIR */
+#define WM8996_GP2_DIR_MASK 0x8000 /* GP2_DIR */
+#define WM8996_GP2_DIR_SHIFT 15 /* GP2_DIR */
+#define WM8996_GP2_DIR_WIDTH 1 /* GP2_DIR */
+#define WM8996_GP2_PU 0x4000 /* GP2_PU */
+#define WM8996_GP2_PU_MASK 0x4000 /* GP2_PU */
+#define WM8996_GP2_PU_SHIFT 14 /* GP2_PU */
+#define WM8996_GP2_PU_WIDTH 1 /* GP2_PU */
+#define WM8996_GP2_PD 0x2000 /* GP2_PD */
+#define WM8996_GP2_PD_MASK 0x2000 /* GP2_PD */
+#define WM8996_GP2_PD_SHIFT 13 /* GP2_PD */
+#define WM8996_GP2_PD_WIDTH 1 /* GP2_PD */
+#define WM8996_GP2_POL 0x0400 /* GP2_POL */
+#define WM8996_GP2_POL_MASK 0x0400 /* GP2_POL */
+#define WM8996_GP2_POL_SHIFT 10 /* GP2_POL */
+#define WM8996_GP2_POL_WIDTH 1 /* GP2_POL */
+#define WM8996_GP2_OP_CFG 0x0200 /* GP2_OP_CFG */
+#define WM8996_GP2_OP_CFG_MASK 0x0200 /* GP2_OP_CFG */
+#define WM8996_GP2_OP_CFG_SHIFT 9 /* GP2_OP_CFG */
+#define WM8996_GP2_OP_CFG_WIDTH 1 /* GP2_OP_CFG */
+#define WM8996_GP2_DB 0x0100 /* GP2_DB */
+#define WM8996_GP2_DB_MASK 0x0100 /* GP2_DB */
+#define WM8996_GP2_DB_SHIFT 8 /* GP2_DB */
+#define WM8996_GP2_DB_WIDTH 1 /* GP2_DB */
+#define WM8996_GP2_LVL 0x0040 /* GP2_LVL */
+#define WM8996_GP2_LVL_MASK 0x0040 /* GP2_LVL */
+#define WM8996_GP2_LVL_SHIFT 6 /* GP2_LVL */
+#define WM8996_GP2_LVL_WIDTH 1 /* GP2_LVL */
+#define WM8996_GP2_FN_MASK 0x000F /* GP2_FN - [3:0] */
+#define WM8996_GP2_FN_SHIFT 0 /* GP2_FN - [3:0] */
+#define WM8996_GP2_FN_WIDTH 4 /* GP2_FN - [3:0] */
+
+/*
+ * R1794 (0x702) - GPIO 3
+ */
+#define WM8996_GP3_DIR 0x8000 /* GP3_DIR */
+#define WM8996_GP3_DIR_MASK 0x8000 /* GP3_DIR */
+#define WM8996_GP3_DIR_SHIFT 15 /* GP3_DIR */
+#define WM8996_GP3_DIR_WIDTH 1 /* GP3_DIR */
+#define WM8996_GP3_PU 0x4000 /* GP3_PU */
+#define WM8996_GP3_PU_MASK 0x4000 /* GP3_PU */
+#define WM8996_GP3_PU_SHIFT 14 /* GP3_PU */
+#define WM8996_GP3_PU_WIDTH 1 /* GP3_PU */
+#define WM8996_GP3_PD 0x2000 /* GP3_PD */
+#define WM8996_GP3_PD_MASK 0x2000 /* GP3_PD */
+#define WM8996_GP3_PD_SHIFT 13 /* GP3_PD */
+#define WM8996_GP3_PD_WIDTH 1 /* GP3_PD */
+#define WM8996_GP3_POL 0x0400 /* GP3_POL */
+#define WM8996_GP3_POL_MASK 0x0400 /* GP3_POL */
+#define WM8996_GP3_POL_SHIFT 10 /* GP3_POL */
+#define WM8996_GP3_POL_WIDTH 1 /* GP3_POL */
+#define WM8996_GP3_OP_CFG 0x0200 /* GP3_OP_CFG */
+#define WM8996_GP3_OP_CFG_MASK 0x0200 /* GP3_OP_CFG */
+#define WM8996_GP3_OP_CFG_SHIFT 9 /* GP3_OP_CFG */
+#define WM8996_GP3_OP_CFG_WIDTH 1 /* GP3_OP_CFG */
+#define WM8996_GP3_DB 0x0100 /* GP3_DB */
+#define WM8996_GP3_DB_MASK 0x0100 /* GP3_DB */
+#define WM8996_GP3_DB_SHIFT 8 /* GP3_DB */
+#define WM8996_GP3_DB_WIDTH 1 /* GP3_DB */
+#define WM8996_GP3_LVL 0x0040 /* GP3_LVL */
+#define WM8996_GP3_LVL_MASK 0x0040 /* GP3_LVL */
+#define WM8996_GP3_LVL_SHIFT 6 /* GP3_LVL */
+#define WM8996_GP3_LVL_WIDTH 1 /* GP3_LVL */
+#define WM8996_GP3_FN_MASK 0x000F /* GP3_FN - [3:0] */
+#define WM8996_GP3_FN_SHIFT 0 /* GP3_FN - [3:0] */
+#define WM8996_GP3_FN_WIDTH 4 /* GP3_FN - [3:0] */
+
+/*
+ * R1795 (0x703) - GPIO 4
+ */
+#define WM8996_GP4_DIR 0x8000 /* GP4_DIR */
+#define WM8996_GP4_DIR_MASK 0x8000 /* GP4_DIR */
+#define WM8996_GP4_DIR_SHIFT 15 /* GP4_DIR */
+#define WM8996_GP4_DIR_WIDTH 1 /* GP4_DIR */
+#define WM8996_GP4_PU 0x4000 /* GP4_PU */
+#define WM8996_GP4_PU_MASK 0x4000 /* GP4_PU */
+#define WM8996_GP4_PU_SHIFT 14 /* GP4_PU */
+#define WM8996_GP4_PU_WIDTH 1 /* GP4_PU */
+#define WM8996_GP4_PD 0x2000 /* GP4_PD */
+#define WM8996_GP4_PD_MASK 0x2000 /* GP4_PD */
+#define WM8996_GP4_PD_SHIFT 13 /* GP4_PD */
+#define WM8996_GP4_PD_WIDTH 1 /* GP4_PD */
+#define WM8996_GP4_POL 0x0400 /* GP4_POL */
+#define WM8996_GP4_POL_MASK 0x0400 /* GP4_POL */
+#define WM8996_GP4_POL_SHIFT 10 /* GP4_POL */
+#define WM8996_GP4_POL_WIDTH 1 /* GP4_POL */
+#define WM8996_GP4_OP_CFG 0x0200 /* GP4_OP_CFG */
+#define WM8996_GP4_OP_CFG_MASK 0x0200 /* GP4_OP_CFG */
+#define WM8996_GP4_OP_CFG_SHIFT 9 /* GP4_OP_CFG */
+#define WM8996_GP4_OP_CFG_WIDTH 1 /* GP4_OP_CFG */
+#define WM8996_GP4_DB 0x0100 /* GP4_DB */
+#define WM8996_GP4_DB_MASK 0x0100 /* GP4_DB */
+#define WM8996_GP4_DB_SHIFT 8 /* GP4_DB */
+#define WM8996_GP4_DB_WIDTH 1 /* GP4_DB */
+#define WM8996_GP4_LVL 0x0040 /* GP4_LVL */
+#define WM8996_GP4_LVL_MASK 0x0040 /* GP4_LVL */
+#define WM8996_GP4_LVL_SHIFT 6 /* GP4_LVL */
+#define WM8996_GP4_LVL_WIDTH 1 /* GP4_LVL */
+#define WM8996_GP4_FN_MASK 0x000F /* GP4_FN - [3:0] */
+#define WM8996_GP4_FN_SHIFT 0 /* GP4_FN - [3:0] */
+#define WM8996_GP4_FN_WIDTH 4 /* GP4_FN - [3:0] */
+
+/*
+ * R1796 (0x704) - GPIO 5
+ */
+#define WM8996_GP5_DIR 0x8000 /* GP5_DIR */
+#define WM8996_GP5_DIR_MASK 0x8000 /* GP5_DIR */
+#define WM8996_GP5_DIR_SHIFT 15 /* GP5_DIR */
+#define WM8996_GP5_DIR_WIDTH 1 /* GP5_DIR */
+#define WM8996_GP5_PU 0x4000 /* GP5_PU */
+#define WM8996_GP5_PU_MASK 0x4000 /* GP5_PU */
+#define WM8996_GP5_PU_SHIFT 14 /* GP5_PU */
+#define WM8996_GP5_PU_WIDTH 1 /* GP5_PU */
+#define WM8996_GP5_PD 0x2000 /* GP5_PD */
+#define WM8996_GP5_PD_MASK 0x2000 /* GP5_PD */
+#define WM8996_GP5_PD_SHIFT 13 /* GP5_PD */
+#define WM8996_GP5_PD_WIDTH 1 /* GP5_PD */
+#define WM8996_GP5_POL 0x0400 /* GP5_POL */
+#define WM8996_GP5_POL_MASK 0x0400 /* GP5_POL */
+#define WM8996_GP5_POL_SHIFT 10 /* GP5_POL */
+#define WM8996_GP5_POL_WIDTH 1 /* GP5_POL */
+#define WM8996_GP5_OP_CFG 0x0200 /* GP5_OP_CFG */
+#define WM8996_GP5_OP_CFG_MASK 0x0200 /* GP5_OP_CFG */
+#define WM8996_GP5_OP_CFG_SHIFT 9 /* GP5_OP_CFG */
+#define WM8996_GP5_OP_CFG_WIDTH 1 /* GP5_OP_CFG */
+#define WM8996_GP5_DB 0x0100 /* GP5_DB */
+#define WM8996_GP5_DB_MASK 0x0100 /* GP5_DB */
+#define WM8996_GP5_DB_SHIFT 8 /* GP5_DB */
+#define WM8996_GP5_DB_WIDTH 1 /* GP5_DB */
+#define WM8996_GP5_LVL 0x0040 /* GP5_LVL */
+#define WM8996_GP5_LVL_MASK 0x0040 /* GP5_LVL */
+#define WM8996_GP5_LVL_SHIFT 6 /* GP5_LVL */
+#define WM8996_GP5_LVL_WIDTH 1 /* GP5_LVL */
+#define WM8996_GP5_FN_MASK 0x000F /* GP5_FN - [3:0] */
+#define WM8996_GP5_FN_SHIFT 0 /* GP5_FN - [3:0] */
+#define WM8996_GP5_FN_WIDTH 4 /* GP5_FN - [3:0] */
+
+/*
+ * R1824 (0x720) - Pull Control (1)
+ */
+#define WM8996_DMICDAT2_PD 0x1000 /* DMICDAT2_PD */
+#define WM8996_DMICDAT2_PD_MASK 0x1000 /* DMICDAT2_PD */
+#define WM8996_DMICDAT2_PD_SHIFT 12 /* DMICDAT2_PD */
+#define WM8996_DMICDAT2_PD_WIDTH 1 /* DMICDAT2_PD */
+#define WM8996_DMICDAT1_PD 0x0400 /* DMICDAT1_PD */
+#define WM8996_DMICDAT1_PD_MASK 0x0400 /* DMICDAT1_PD */
+#define WM8996_DMICDAT1_PD_SHIFT 10 /* DMICDAT1_PD */
+#define WM8996_DMICDAT1_PD_WIDTH 1 /* DMICDAT1_PD */
+#define WM8996_MCLK2_PU 0x0200 /* MCLK2_PU */
+#define WM8996_MCLK2_PU_MASK 0x0200 /* MCLK2_PU */
+#define WM8996_MCLK2_PU_SHIFT 9 /* MCLK2_PU */
+#define WM8996_MCLK2_PU_WIDTH 1 /* MCLK2_PU */
+#define WM8996_MCLK2_PD 0x0100 /* MCLK2_PD */
+#define WM8996_MCLK2_PD_MASK 0x0100 /* MCLK2_PD */
+#define WM8996_MCLK2_PD_SHIFT 8 /* MCLK2_PD */
+#define WM8996_MCLK2_PD_WIDTH 1 /* MCLK2_PD */
+#define WM8996_MCLK1_PU 0x0080 /* MCLK1_PU */
+#define WM8996_MCLK1_PU_MASK 0x0080 /* MCLK1_PU */
+#define WM8996_MCLK1_PU_SHIFT 7 /* MCLK1_PU */
+#define WM8996_MCLK1_PU_WIDTH 1 /* MCLK1_PU */
+#define WM8996_MCLK1_PD 0x0040 /* MCLK1_PD */
+#define WM8996_MCLK1_PD_MASK 0x0040 /* MCLK1_PD */
+#define WM8996_MCLK1_PD_SHIFT 6 /* MCLK1_PD */
+#define WM8996_MCLK1_PD_WIDTH 1 /* MCLK1_PD */
+#define WM8996_DACDAT1_PU 0x0020 /* DACDAT1_PU */
+#define WM8996_DACDAT1_PU_MASK 0x0020 /* DACDAT1_PU */
+#define WM8996_DACDAT1_PU_SHIFT 5 /* DACDAT1_PU */
+#define WM8996_DACDAT1_PU_WIDTH 1 /* DACDAT1_PU */
+#define WM8996_DACDAT1_PD 0x0010 /* DACDAT1_PD */
+#define WM8996_DACDAT1_PD_MASK 0x0010 /* DACDAT1_PD */
+#define WM8996_DACDAT1_PD_SHIFT 4 /* DACDAT1_PD */
+#define WM8996_DACDAT1_PD_WIDTH 1 /* DACDAT1_PD */
+#define WM8996_DACLRCLK1_PU 0x0008 /* DACLRCLK1_PU */
+#define WM8996_DACLRCLK1_PU_MASK 0x0008 /* DACLRCLK1_PU */
+#define WM8996_DACLRCLK1_PU_SHIFT 3 /* DACLRCLK1_PU */
+#define WM8996_DACLRCLK1_PU_WIDTH 1 /* DACLRCLK1_PU */
+#define WM8996_DACLRCLK1_PD 0x0004 /* DACLRCLK1_PD */
+#define WM8996_DACLRCLK1_PD_MASK 0x0004 /* DACLRCLK1_PD */
+#define WM8996_DACLRCLK1_PD_SHIFT 2 /* DACLRCLK1_PD */
+#define WM8996_DACLRCLK1_PD_WIDTH 1 /* DACLRCLK1_PD */
+#define WM8996_BCLK1_PU 0x0002 /* BCLK1_PU */
+#define WM8996_BCLK1_PU_MASK 0x0002 /* BCLK1_PU */
+#define WM8996_BCLK1_PU_SHIFT 1 /* BCLK1_PU */
+#define WM8996_BCLK1_PU_WIDTH 1 /* BCLK1_PU */
+#define WM8996_BCLK1_PD 0x0001 /* BCLK1_PD */
+#define WM8996_BCLK1_PD_MASK 0x0001 /* BCLK1_PD */
+#define WM8996_BCLK1_PD_SHIFT 0 /* BCLK1_PD */
+#define WM8996_BCLK1_PD_WIDTH 1 /* BCLK1_PD */
+
+/*
+ * R1825 (0x721) - Pull Control (2)
+ */
+#define WM8996_LDO1ENA_PD 0x0100 /* LDO1ENA_PD */
+#define WM8996_LDO1ENA_PD_MASK 0x0100 /* LDO1ENA_PD */
+#define WM8996_LDO1ENA_PD_SHIFT 8 /* LDO1ENA_PD */
+#define WM8996_LDO1ENA_PD_WIDTH 1 /* LDO1ENA_PD */
+#define WM8996_ADDR_PD 0x0040 /* ADDR_PD */
+#define WM8996_ADDR_PD_MASK 0x0040 /* ADDR_PD */
+#define WM8996_ADDR_PD_SHIFT 6 /* ADDR_PD */
+#define WM8996_ADDR_PD_WIDTH 1 /* ADDR_PD */
+#define WM8996_DACDAT2_PU 0x0020 /* DACDAT2_PU */
+#define WM8996_DACDAT2_PU_MASK 0x0020 /* DACDAT2_PU */
+#define WM8996_DACDAT2_PU_SHIFT 5 /* DACDAT2_PU */
+#define WM8996_DACDAT2_PU_WIDTH 1 /* DACDAT2_PU */
+#define WM8996_DACDAT2_PD 0x0010 /* DACDAT2_PD */
+#define WM8996_DACDAT2_PD_MASK 0x0010 /* DACDAT2_PD */
+#define WM8996_DACDAT2_PD_SHIFT 4 /* DACDAT2_PD */
+#define WM8996_DACDAT2_PD_WIDTH 1 /* DACDAT2_PD */
+#define WM8996_DACLRCLK2_PU 0x0008 /* DACLRCLK2_PU */
+#define WM8996_DACLRCLK2_PU_MASK 0x0008 /* DACLRCLK2_PU */
+#define WM8996_DACLRCLK2_PU_SHIFT 3 /* DACLRCLK2_PU */
+#define WM8996_DACLRCLK2_PU_WIDTH 1 /* DACLRCLK2_PU */
+#define WM8996_DACLRCLK2_PD 0x0004 /* DACLRCLK2_PD */
+#define WM8996_DACLRCLK2_PD_MASK 0x0004 /* DACLRCLK2_PD */
+#define WM8996_DACLRCLK2_PD_SHIFT 2 /* DACLRCLK2_PD */
+#define WM8996_DACLRCLK2_PD_WIDTH 1 /* DACLRCLK2_PD */
+#define WM8996_BCLK2_PU 0x0002 /* BCLK2_PU */
+#define WM8996_BCLK2_PU_MASK 0x0002 /* BCLK2_PU */
+#define WM8996_BCLK2_PU_SHIFT 1 /* BCLK2_PU */
+#define WM8996_BCLK2_PU_WIDTH 1 /* BCLK2_PU */
+#define WM8996_BCLK2_PD 0x0001 /* BCLK2_PD */
+#define WM8996_BCLK2_PD_MASK 0x0001 /* BCLK2_PD */
+#define WM8996_BCLK2_PD_SHIFT 0 /* BCLK2_PD */
+#define WM8996_BCLK2_PD_WIDTH 1 /* BCLK2_PD */
+
+/*
+ * R1840 (0x730) - Interrupt Status 1
+ */
+#define WM8996_GP5_EINT 0x0010 /* GP5_EINT */
+#define WM8996_GP5_EINT_MASK 0x0010 /* GP5_EINT */
+#define WM8996_GP5_EINT_SHIFT 4 /* GP5_EINT */
+#define WM8996_GP5_EINT_WIDTH 1 /* GP5_EINT */
+#define WM8996_GP4_EINT 0x0008 /* GP4_EINT */
+#define WM8996_GP4_EINT_MASK 0x0008 /* GP4_EINT */
+#define WM8996_GP4_EINT_SHIFT 3 /* GP4_EINT */
+#define WM8996_GP4_EINT_WIDTH 1 /* GP4_EINT */
+#define WM8996_GP3_EINT 0x0004 /* GP3_EINT */
+#define WM8996_GP3_EINT_MASK 0x0004 /* GP3_EINT */
+#define WM8996_GP3_EINT_SHIFT 2 /* GP3_EINT */
+#define WM8996_GP3_EINT_WIDTH 1 /* GP3_EINT */
+#define WM8996_GP2_EINT 0x0002 /* GP2_EINT */
+#define WM8996_GP2_EINT_MASK 0x0002 /* GP2_EINT */
+#define WM8996_GP2_EINT_SHIFT 1 /* GP2_EINT */
+#define WM8996_GP2_EINT_WIDTH 1 /* GP2_EINT */
+#define WM8996_GP1_EINT 0x0001 /* GP1_EINT */
+#define WM8996_GP1_EINT_MASK 0x0001 /* GP1_EINT */
+#define WM8996_GP1_EINT_SHIFT 0 /* GP1_EINT */
+#define WM8996_GP1_EINT_WIDTH 1 /* GP1_EINT */
+
+/*
+ * R1841 (0x731) - Interrupt Status 2
+ */
+#define WM8996_DCS_DONE_23_EINT 0x1000 /* DCS_DONE_23_EINT */
+#define WM8996_DCS_DONE_23_EINT_MASK 0x1000 /* DCS_DONE_23_EINT */
+#define WM8996_DCS_DONE_23_EINT_SHIFT 12 /* DCS_DONE_23_EINT */
+#define WM8996_DCS_DONE_23_EINT_WIDTH 1 /* DCS_DONE_23_EINT */
+#define WM8996_DCS_DONE_01_EINT 0x0800 /* DCS_DONE_01_EINT */
+#define WM8996_DCS_DONE_01_EINT_MASK 0x0800 /* DCS_DONE_01_EINT */
+#define WM8996_DCS_DONE_01_EINT_SHIFT 11 /* DCS_DONE_01_EINT */
+#define WM8996_DCS_DONE_01_EINT_WIDTH 1 /* DCS_DONE_01_EINT */
+#define WM8996_WSEQ_DONE_EINT 0x0400 /* WSEQ_DONE_EINT */
+#define WM8996_WSEQ_DONE_EINT_MASK 0x0400 /* WSEQ_DONE_EINT */
+#define WM8996_WSEQ_DONE_EINT_SHIFT 10 /* WSEQ_DONE_EINT */
+#define WM8996_WSEQ_DONE_EINT_WIDTH 1 /* WSEQ_DONE_EINT */
+#define WM8996_FIFOS_ERR_EINT 0x0200 /* FIFOS_ERR_EINT */
+#define WM8996_FIFOS_ERR_EINT_MASK 0x0200 /* FIFOS_ERR_EINT */
+#define WM8996_FIFOS_ERR_EINT_SHIFT 9 /* FIFOS_ERR_EINT */
+#define WM8996_FIFOS_ERR_EINT_WIDTH 1 /* FIFOS_ERR_EINT */
+#define WM8996_DSP2DRC_SIG_DET_EINT 0x0080 /* DSP2DRC_SIG_DET_EINT */
+#define WM8996_DSP2DRC_SIG_DET_EINT_MASK 0x0080 /* DSP2DRC_SIG_DET_EINT */
+#define WM8996_DSP2DRC_SIG_DET_EINT_SHIFT 7 /* DSP2DRC_SIG_DET_EINT */
+#define WM8996_DSP2DRC_SIG_DET_EINT_WIDTH 1 /* DSP2DRC_SIG_DET_EINT */
+#define WM8996_DSP1DRC_SIG_DET_EINT 0x0040 /* DSP1DRC_SIG_DET_EINT */
+#define WM8996_DSP1DRC_SIG_DET_EINT_MASK 0x0040 /* DSP1DRC_SIG_DET_EINT */
+#define WM8996_DSP1DRC_SIG_DET_EINT_SHIFT 6 /* DSP1DRC_SIG_DET_EINT */
+#define WM8996_DSP1DRC_SIG_DET_EINT_WIDTH 1 /* DSP1DRC_SIG_DET_EINT */
+#define WM8996_FLL_SW_CLK_DONE_EINT 0x0008 /* FLL_SW_CLK_DONE_EINT */
+#define WM8996_FLL_SW_CLK_DONE_EINT_MASK 0x0008 /* FLL_SW_CLK_DONE_EINT */
+#define WM8996_FLL_SW_CLK_DONE_EINT_SHIFT 3 /* FLL_SW_CLK_DONE_EINT */
+#define WM8996_FLL_SW_CLK_DONE_EINT_WIDTH 1 /* FLL_SW_CLK_DONE_EINT */
+#define WM8996_FLL_LOCK_EINT 0x0004 /* FLL_LOCK_EINT */
+#define WM8996_FLL_LOCK_EINT_MASK 0x0004 /* FLL_LOCK_EINT */
+#define WM8996_FLL_LOCK_EINT_SHIFT 2 /* FLL_LOCK_EINT */
+#define WM8996_FLL_LOCK_EINT_WIDTH 1 /* FLL_LOCK_EINT */
+#define WM8996_HP_DONE_EINT 0x0002 /* HP_DONE_EINT */
+#define WM8996_HP_DONE_EINT_MASK 0x0002 /* HP_DONE_EINT */
+#define WM8996_HP_DONE_EINT_SHIFT 1 /* HP_DONE_EINT */
+#define WM8996_HP_DONE_EINT_WIDTH 1 /* HP_DONE_EINT */
+#define WM8996_MICD_EINT 0x0001 /* MICD_EINT */
+#define WM8996_MICD_EINT_MASK 0x0001 /* MICD_EINT */
+#define WM8996_MICD_EINT_SHIFT 0 /* MICD_EINT */
+#define WM8996_MICD_EINT_WIDTH 1 /* MICD_EINT */
+
+/*
+ * R1842 (0x732) - Interrupt Raw Status 2
+ */
+#define WM8996_DCS_DONE_23_STS 0x1000 /* DCS_DONE_23_STS */
+#define WM8996_DCS_DONE_23_STS_MASK 0x1000 /* DCS_DONE_23_STS */
+#define WM8996_DCS_DONE_23_STS_SHIFT 12 /* DCS_DONE_23_STS */
+#define WM8996_DCS_DONE_23_STS_WIDTH 1 /* DCS_DONE_23_STS */
+#define WM8996_DCS_DONE_01_STS 0x0800 /* DCS_DONE_01_STS */
+#define WM8996_DCS_DONE_01_STS_MASK 0x0800 /* DCS_DONE_01_STS */
+#define WM8996_DCS_DONE_01_STS_SHIFT 11 /* DCS_DONE_01_STS */
+#define WM8996_DCS_DONE_01_STS_WIDTH 1 /* DCS_DONE_01_STS */
+#define WM8996_WSEQ_DONE_STS 0x0400 /* WSEQ_DONE_STS */
+#define WM8996_WSEQ_DONE_STS_MASK 0x0400 /* WSEQ_DONE_STS */
+#define WM8996_WSEQ_DONE_STS_SHIFT 10 /* WSEQ_DONE_STS */
+#define WM8996_WSEQ_DONE_STS_WIDTH 1 /* WSEQ_DONE_STS */
+#define WM8996_FIFOS_ERR_STS 0x0200 /* FIFOS_ERR_STS */
+#define WM8996_FIFOS_ERR_STS_MASK 0x0200 /* FIFOS_ERR_STS */
+#define WM8996_FIFOS_ERR_STS_SHIFT 9 /* FIFOS_ERR_STS */
+#define WM8996_FIFOS_ERR_STS_WIDTH 1 /* FIFOS_ERR_STS */
+#define WM8996_DSP2DRC_SIG_DET_STS 0x0080 /* DSP2DRC_SIG_DET_STS */
+#define WM8996_DSP2DRC_SIG_DET_STS_MASK 0x0080 /* DSP2DRC_SIG_DET_STS */
+#define WM8996_DSP2DRC_SIG_DET_STS_SHIFT 7 /* DSP2DRC_SIG_DET_STS */
+#define WM8996_DSP2DRC_SIG_DET_STS_WIDTH 1 /* DSP2DRC_SIG_DET_STS */
+#define WM8996_DSP1DRC_SIG_DET_STS 0x0040 /* DSP1DRC_SIG_DET_STS */
+#define WM8996_DSP1DRC_SIG_DET_STS_MASK 0x0040 /* DSP1DRC_SIG_DET_STS */
+#define WM8996_DSP1DRC_SIG_DET_STS_SHIFT 6 /* DSP1DRC_SIG_DET_STS */
+#define WM8996_DSP1DRC_SIG_DET_STS_WIDTH 1 /* DSP1DRC_SIG_DET_STS */
+#define WM8996_FLL_LOCK_STS 0x0004 /* FLL_LOCK_STS */
+#define WM8996_FLL_LOCK_STS_MASK 0x0004 /* FLL_LOCK_STS */
+#define WM8996_FLL_LOCK_STS_SHIFT 2 /* FLL_LOCK_STS */
+#define WM8996_FLL_LOCK_STS_WIDTH 1 /* FLL_LOCK_STS */
+
+/*
+ * R1848 (0x738) - Interrupt Status 1 Mask
+ */
+#define WM8996_IM_GP5_EINT 0x0010 /* IM_GP5_EINT */
+#define WM8996_IM_GP5_EINT_MASK 0x0010 /* IM_GP5_EINT */
+#define WM8996_IM_GP5_EINT_SHIFT 4 /* IM_GP5_EINT */
+#define WM8996_IM_GP5_EINT_WIDTH 1 /* IM_GP5_EINT */
+#define WM8996_IM_GP4_EINT 0x0008 /* IM_GP4_EINT */
+#define WM8996_IM_GP4_EINT_MASK 0x0008 /* IM_GP4_EINT */
+#define WM8996_IM_GP4_EINT_SHIFT 3 /* IM_GP4_EINT */
+#define WM8996_IM_GP4_EINT_WIDTH 1 /* IM_GP4_EINT */
+#define WM8996_IM_GP3_EINT 0x0004 /* IM_GP3_EINT */
+#define WM8996_IM_GP3_EINT_MASK 0x0004 /* IM_GP3_EINT */
+#define WM8996_IM_GP3_EINT_SHIFT 2 /* IM_GP3_EINT */
+#define WM8996_IM_GP3_EINT_WIDTH 1 /* IM_GP3_EINT */
+#define WM8996_IM_GP2_EINT 0x0002 /* IM_GP2_EINT */
+#define WM8996_IM_GP2_EINT_MASK 0x0002 /* IM_GP2_EINT */
+#define WM8996_IM_GP2_EINT_SHIFT 1 /* IM_GP2_EINT */
+#define WM8996_IM_GP2_EINT_WIDTH 1 /* IM_GP2_EINT */
+#define WM8996_IM_GP1_EINT 0x0001 /* IM_GP1_EINT */
+#define WM8996_IM_GP1_EINT_MASK 0x0001 /* IM_GP1_EINT */
+#define WM8996_IM_GP1_EINT_SHIFT 0 /* IM_GP1_EINT */
+#define WM8996_IM_GP1_EINT_WIDTH 1 /* IM_GP1_EINT */
+
+/*
+ * R1849 (0x739) - Interrupt Status 2 Mask
+ */
+#define WM8996_IM_DCS_DONE_23_EINT 0x1000 /* IM_DCS_DONE_23_EINT */
+#define WM8996_IM_DCS_DONE_23_EINT_MASK 0x1000 /* IM_DCS_DONE_23_EINT */
+#define WM8996_IM_DCS_DONE_23_EINT_SHIFT 12 /* IM_DCS_DONE_23_EINT */
+#define WM8996_IM_DCS_DONE_23_EINT_WIDTH 1 /* IM_DCS_DONE_23_EINT */
+#define WM8996_IM_DCS_DONE_01_EINT 0x0800 /* IM_DCS_DONE_01_EINT */
+#define WM8996_IM_DCS_DONE_01_EINT_MASK 0x0800 /* IM_DCS_DONE_01_EINT */
+#define WM8996_IM_DCS_DONE_01_EINT_SHIFT 11 /* IM_DCS_DONE_01_EINT */
+#define WM8996_IM_DCS_DONE_01_EINT_WIDTH 1 /* IM_DCS_DONE_01_EINT */
+#define WM8996_IM_WSEQ_DONE_EINT 0x0400 /* IM_WSEQ_DONE_EINT */
+#define WM8996_IM_WSEQ_DONE_EINT_MASK 0x0400 /* IM_WSEQ_DONE_EINT */
+#define WM8996_IM_WSEQ_DONE_EINT_SHIFT 10 /* IM_WSEQ_DONE_EINT */
+#define WM8996_IM_WSEQ_DONE_EINT_WIDTH 1 /* IM_WSEQ_DONE_EINT */
+#define WM8996_IM_FIFOS_ERR_EINT 0x0200 /* IM_FIFOS_ERR_EINT */
+#define WM8996_IM_FIFOS_ERR_EINT_MASK 0x0200 /* IM_FIFOS_ERR_EINT */
+#define WM8996_IM_FIFOS_ERR_EINT_SHIFT 9 /* IM_FIFOS_ERR_EINT */
+#define WM8996_IM_FIFOS_ERR_EINT_WIDTH 1 /* IM_FIFOS_ERR_EINT */
+#define WM8996_IM_DSP2DRC_SIG_DET_EINT 0x0080 /* IM_DSP2DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP2DRC_SIG_DET_EINT_MASK 0x0080 /* IM_DSP2DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP2DRC_SIG_DET_EINT_SHIFT 7 /* IM_DSP2DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP2DRC_SIG_DET_EINT_WIDTH 1 /* IM_DSP2DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP1DRC_SIG_DET_EINT 0x0040 /* IM_DSP1DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP1DRC_SIG_DET_EINT_MASK 0x0040 /* IM_DSP1DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP1DRC_SIG_DET_EINT_SHIFT 6 /* IM_DSP1DRC_SIG_DET_EINT */
+#define WM8996_IM_DSP1DRC_SIG_DET_EINT_WIDTH 1 /* IM_DSP1DRC_SIG_DET_EINT */
+#define WM8996_IM_FLL_SW_CLK_DONE_EINT 0x0008 /* IM_FLL_SW_CLK_DONE_EINT */
+#define WM8996_IM_FLL_SW_CLK_DONE_EINT_MASK 0x0008 /* IM_FLL_SW_CLK_DONE_EINT */
+#define WM8996_IM_FLL_SW_CLK_DONE_EINT_SHIFT 3 /* IM_FLL_SW_CLK_DONE_EINT */
+#define WM8996_IM_FLL_SW_CLK_DONE_EINT_WIDTH 1 /* IM_FLL_SW_CLK_DONE_EINT */
+#define WM8996_IM_FLL_LOCK_EINT 0x0004 /* IM_FLL_LOCK_EINT */
+#define WM8996_IM_FLL_LOCK_EINT_MASK 0x0004 /* IM_FLL_LOCK_EINT */
+#define WM8996_IM_FLL_LOCK_EINT_SHIFT 2 /* IM_FLL_LOCK_EINT */
+#define WM8996_IM_FLL_LOCK_EINT_WIDTH 1 /* IM_FLL_LOCK_EINT */
+#define WM8996_IM_HP_DONE_EINT 0x0002 /* IM_HP_DONE_EINT */
+#define WM8996_IM_HP_DONE_EINT_MASK 0x0002 /* IM_HP_DONE_EINT */
+#define WM8996_IM_HP_DONE_EINT_SHIFT 1 /* IM_HP_DONE_EINT */
+#define WM8996_IM_HP_DONE_EINT_WIDTH 1 /* IM_HP_DONE_EINT */
+#define WM8996_IM_MICD_EINT 0x0001 /* IM_MICD_EINT */
+#define WM8996_IM_MICD_EINT_MASK 0x0001 /* IM_MICD_EINT */
+#define WM8996_IM_MICD_EINT_SHIFT 0 /* IM_MICD_EINT */
+#define WM8996_IM_MICD_EINT_WIDTH 1 /* IM_MICD_EINT */
+
+/*
+ * R1856 (0x740) - Interrupt Control
+ */
+#define WM8996_IM_IRQ 0x0001 /* IM_IRQ */
+#define WM8996_IM_IRQ_MASK 0x0001 /* IM_IRQ */
+#define WM8996_IM_IRQ_SHIFT 0 /* IM_IRQ */
+#define WM8996_IM_IRQ_WIDTH 1 /* IM_IRQ */
+
+/*
+ * R2048 (0x800) - Left PDM Speaker
+ */
+#define WM8996_SPKL_ENA 0x0010 /* SPKL_ENA */
+#define WM8996_SPKL_ENA_MASK 0x0010 /* SPKL_ENA */
+#define WM8996_SPKL_ENA_SHIFT 4 /* SPKL_ENA */
+#define WM8996_SPKL_ENA_WIDTH 1 /* SPKL_ENA */
+#define WM8996_SPKL_MUTE 0x0008 /* SPKL_MUTE */
+#define WM8996_SPKL_MUTE_MASK 0x0008 /* SPKL_MUTE */
+#define WM8996_SPKL_MUTE_SHIFT 3 /* SPKL_MUTE */
+#define WM8996_SPKL_MUTE_WIDTH 1 /* SPKL_MUTE */
+#define WM8996_SPKL_MUTE_ZC 0x0004 /* SPKL_MUTE_ZC */
+#define WM8996_SPKL_MUTE_ZC_MASK 0x0004 /* SPKL_MUTE_ZC */
+#define WM8996_SPKL_MUTE_ZC_SHIFT 2 /* SPKL_MUTE_ZC */
+#define WM8996_SPKL_MUTE_ZC_WIDTH 1 /* SPKL_MUTE_ZC */
+#define WM8996_SPKL_SRC_MASK 0x0003 /* SPKL_SRC - [1:0] */
+#define WM8996_SPKL_SRC_SHIFT 0 /* SPKL_SRC - [1:0] */
+#define WM8996_SPKL_SRC_WIDTH 2 /* SPKL_SRC - [1:0] */
+
+/*
+ * R2049 (0x801) - Right PDM Speaker
+ */
+#define WM8996_SPKR_ENA 0x0010 /* SPKR_ENA */
+#define WM8996_SPKR_ENA_MASK 0x0010 /* SPKR_ENA */
+#define WM8996_SPKR_ENA_SHIFT 4 /* SPKR_ENA */
+#define WM8996_SPKR_ENA_WIDTH 1 /* SPKR_ENA */
+#define WM8996_SPKR_MUTE 0x0008 /* SPKR_MUTE */
+#define WM8996_SPKR_MUTE_MASK 0x0008 /* SPKR_MUTE */
+#define WM8996_SPKR_MUTE_SHIFT 3 /* SPKR_MUTE */
+#define WM8996_SPKR_MUTE_WIDTH 1 /* SPKR_MUTE */
+#define WM8996_SPKR_MUTE_ZC 0x0004 /* SPKR_MUTE_ZC */
+#define WM8996_SPKR_MUTE_ZC_MASK 0x0004 /* SPKR_MUTE_ZC */
+#define WM8996_SPKR_MUTE_ZC_SHIFT 2 /* SPKR_MUTE_ZC */
+#define WM8996_SPKR_MUTE_ZC_WIDTH 1 /* SPKR_MUTE_ZC */
+#define WM8996_SPKR_SRC_MASK 0x0003 /* SPKR_SRC - [1:0] */
+#define WM8996_SPKR_SRC_SHIFT 0 /* SPKR_SRC - [1:0] */
+#define WM8996_SPKR_SRC_WIDTH 2 /* SPKR_SRC - [1:0] */
+
+/*
+ * R2050 (0x802) - PDM Speaker Mute Sequence
+ */
+#define WM8996_SPK_MUTE_ENDIAN 0x0100 /* SPK_MUTE_ENDIAN */
+#define WM8996_SPK_MUTE_ENDIAN_MASK 0x0100 /* SPK_MUTE_ENDIAN */
+#define WM8996_SPK_MUTE_ENDIAN_SHIFT 8 /* SPK_MUTE_ENDIAN */
+#define WM8996_SPK_MUTE_ENDIAN_WIDTH 1 /* SPK_MUTE_ENDIAN */
+#define WM8996_SPK_MUTE_SEQ1_MASK 0x00FF /* SPK_MUTE_SEQ1 - [7:0] */
+#define WM8996_SPK_MUTE_SEQ1_SHIFT 0 /* SPK_MUTE_SEQ1 - [7:0] */
+#define WM8996_SPK_MUTE_SEQ1_WIDTH 8 /* SPK_MUTE_SEQ1 - [7:0] */
+
+/*
+ * R2051 (0x803) - PDM Speaker Volume
+ */
+#define WM8996_SPKR_VOL_MASK 0x00F0 /* SPKR_VOL - [7:4] */
+#define WM8996_SPKR_VOL_SHIFT 4 /* SPKR_VOL - [7:4] */
+#define WM8996_SPKR_VOL_WIDTH 4 /* SPKR_VOL - [7:4] */
+#define WM8996_SPKL_VOL_MASK 0x000F /* SPKL_VOL - [3:0] */
+#define WM8996_SPKL_VOL_SHIFT 0 /* SPKL_VOL - [3:0] */
+#define WM8996_SPKL_VOL_WIDTH 4 /* SPKL_VOL - [3:0] */
+
+#endif
reg |= WM8993_HPOUT1L_DLY | WM8993_HPOUT1R_DLY;
snd_soc_write(codec, WM8993_ANALOGUE_HP_0, reg);
- /* Smallest supported update interval */
snd_soc_update_bits(codec, WM8993_DC_SERVO_1,
- WM8993_DCS_TIMER_PERIOD_01_MASK, 1);
+ WM8993_DCS_TIMER_PERIOD_01_MASK, 0);
calibrate_dc_servo(codec);
tristate "Audio support for Wolfson Speyside"
depends on SND_SOC_SAMSUNG && MACH_WLF_CRAGG_6410
select SND_SAMSUNG_I2S
- select SND_SOC_WM8915
+ select SND_SOC_WM8996
select SND_SOC_WM9081
config SND_SOC_SPEYSIDE_WM8962
#include <sound/jack.h>
#include <linux/gpio.h>
-#include "../codecs/wm8915.h"
+#include "../codecs/wm8996.h"
#include "../codecs/wm9081.h"
-#define WM8915_HPSEL_GPIO 214
+#define WM8996_HPSEL_GPIO 214
static int speyside_set_bias_level(struct snd_soc_card *card,
struct snd_soc_dapm_context *dapm,
switch (level) {
case SND_SOC_BIAS_STANDBY:
- ret = snd_soc_dai_set_sysclk(codec_dai, WM8915_SYSCLK_MCLK2,
+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8996_SYSCLK_MCLK2,
32768, SND_SOC_CLOCK_IN);
if (ret < 0)
return ret;
- ret = snd_soc_dai_set_pll(codec_dai, WM8915_FLL_MCLK2,
+ ret = snd_soc_dai_set_pll(codec_dai, WM8996_FLL_MCLK2,
0, 0, 0);
if (ret < 0) {
pr_err("Failed to stop FLL\n");
case SND_SOC_BIAS_PREPARE:
if (card->dapm.bias_level == SND_SOC_BIAS_STANDBY) {
ret = snd_soc_dai_set_pll(codec_dai, 0,
- WM8915_FLL_MCLK2,
+ WM8996_FLL_MCLK2,
32768, 48000 * 256);
if (ret < 0) {
pr_err("Failed to start FLL\n");
}
ret = snd_soc_dai_set_sysclk(codec_dai,
- WM8915_SYSCLK_FLL,
+ WM8996_SYSCLK_FLL,
48000 * 256,
SND_SOC_CLOCK_IN);
if (ret < 0)
int polarity)
{
speyside_jack_polarity = !polarity;
- gpio_direction_output(WM8915_HPSEL_GPIO, speyside_jack_polarity);
+ gpio_direction_output(WM8996_HPSEL_GPIO, speyside_jack_polarity);
/* Re-run DAPM to make sure we're using the correct mic bias */
snd_soc_dapm_sync(&codec->dapm);
}
-static int speyside_wm8915_init(struct snd_soc_pcm_runtime *rtd)
+static int speyside_wm8996_init(struct snd_soc_pcm_runtime *rtd)
{
struct snd_soc_dai *dai = rtd->codec_dai;
struct snd_soc_codec *codec = rtd->codec;
int ret;
- ret = snd_soc_dai_set_sysclk(dai, WM8915_SYSCLK_MCLK2, 32768, 0);
+ ret = snd_soc_dai_set_sysclk(dai, WM8996_SYSCLK_MCLK2, 32768, 0);
if (ret < 0)
return ret;
- ret = gpio_request(WM8915_HPSEL_GPIO, "HP_SEL");
+ ret = gpio_request(WM8996_HPSEL_GPIO, "HP_SEL");
if (ret != 0)
pr_err("Failed to request HP_SEL GPIO: %d\n", ret);
- gpio_direction_output(WM8915_HPSEL_GPIO, speyside_jack_polarity);
+ gpio_direction_output(WM8996_HPSEL_GPIO, speyside_jack_polarity);
ret = snd_soc_jack_new(codec, "Headset",
SND_JACK_HEADSET | SND_JACK_BTN_0,
if (ret)
return ret;
- wm8915_detect(codec, &speyside_headset, speyside_set_polarity);
+ wm8996_detect(codec, &speyside_headset, speyside_set_polarity);
return 0;
}
.name = "CPU",
.stream_name = "CPU",
.cpu_dai_name = "samsung-i2s.0",
- .codec_dai_name = "wm8915-aif1",
+ .codec_dai_name = "wm8996-aif1",
.platform_name = "samsung-audio",
- .codec_name = "wm8915.1-001a",
- .init = speyside_wm8915_init,
+ .codec_name = "wm8996.1-001a",
+ .init = speyside_wm8996_init,
.ops = &speyside_ops,
},
{
.name = "Baseband",
.stream_name = "Baseband",
- .cpu_dai_name = "wm8915-aif2",
+ .cpu_dai_name = "wm8996-aif2",
.codec_dai_name = "wm1250-ev1",
.codec_name = "wm1250-ev1.1-0027",
.ops = &speyside_ops,
static unsigned short keycode_rk2[] = { KEY_1, KEY_2, KEY_3, KEY_4,
KEY_5, KEY_6, KEY_7 };
static unsigned short keycode_rk3[] = { KEY_1, KEY_2, KEY_3, KEY_4,
- KEY_5, KEY_6, KEY_7, KEY_5, KEY_6 };
+ KEY_5, KEY_6, KEY_7, KEY_8, KEY_9 };
static unsigned short keycode_kore[] = {
KEY_FN_F1, /* "menu" */
continue;
}
if (((protocol == UAC_VERSION_1) && (fmt->bLength < 8)) ||
- ((protocol == UAC_VERSION_2) && (fmt->bLength != 6))) {
+ ((protocol == UAC_VERSION_2) && (fmt->bLength < 6))) {
snd_printk(KERN_ERR "%d:%u:%d : invalid UAC_FORMAT_TYPE desc\n",
dev->devnum, iface_no, altno);
continue;
if (state->mixer->protocol == UAC_VERSION_1) {
csize = hdr->bControlSize;
+ if (!csize) {
+ snd_printdd(KERN_ERR "usbaudio: unit %u: "
+ "invalid bControlSize == 0\n", unitid);
+ return -EINVAL;
+ }
channels = (hdr->bLength - 7) / csize - 1;
bmaControls = hdr->bmaControls;
} else {
struct mixer_build state;
int err;
const struct usbmix_ctl_map *map;
- struct usb_host_interface *hostif;
void *p;
- hostif = mixer->chip->ctrl_intf;
memset(&state, 0, sizeof(state));
state.chip = mixer->chip;
state.mixer = mixer;
- state.buffer = hostif->extra;
- state.buflen = hostif->extralen;
+ state.buffer = mixer->hostif->extra;
+ state.buflen = mixer->hostif->extralen;
/* check the mapping table */
for (map = usbmix_ctl_maps; map->id; map++) {
}
p = NULL;
- while ((p = snd_usb_find_csint_desc(hostif->extra, hostif->extralen, p, UAC_OUTPUT_TERMINAL)) != NULL) {
+ while ((p = snd_usb_find_csint_desc(mixer->hostif->extra, mixer->hostif->extralen,
+ p, UAC_OUTPUT_TERMINAL)) != NULL) {
if (mixer->protocol == UAC_VERSION_1) {
struct uac1_output_terminal_descriptor *desc = p;
/* create the handler for the optional status interrupt endpoint */
static int snd_usb_mixer_status_create(struct usb_mixer_interface *mixer)
{
- struct usb_host_interface *hostif;
struct usb_endpoint_descriptor *ep;
void *transfer_buffer;
int buffer_length;
unsigned int epnum;
- hostif = mixer->chip->ctrl_intf;
/* we need one interrupt input endpoint */
- if (get_iface_desc(hostif)->bNumEndpoints < 1)
+ if (get_iface_desc(mixer->hostif)->bNumEndpoints < 1)
return 0;
- ep = get_endpoint(hostif, 0);
+ ep = get_endpoint(mixer->hostif, 0);
if (!usb_endpoint_dir_in(ep) || !usb_endpoint_xfer_int(ep))
return 0;
};
struct usb_mixer_interface *mixer;
struct snd_info_entry *entry;
- struct usb_host_interface *host_iface;
int err;
strcpy(chip->card->mixername, "USB Mixer");
return -ENOMEM;
}
- host_iface = &usb_ifnum_to_if(chip->dev, ctrlif)->altsetting[0];
- switch (get_iface_desc(host_iface)->bInterfaceProtocol) {
+ mixer->hostif = &usb_ifnum_to_if(chip->dev, ctrlif)->altsetting[0];
+ switch (get_iface_desc(mixer->hostif)->bInterfaceProtocol) {
case UAC_VERSION_1:
default:
mixer->protocol = UAC_VERSION_1;
struct usb_mixer_interface {
struct snd_usb_audio *chip;
+ struct usb_host_interface *hostif;
struct list_head list;
unsigned int ignore_ctl_error;
struct urb *urb;
.idProduct = 0x1020,
},
+/* KeithMcMillen Stringport */
+{
+ USB_DEVICE(0x1f38, 0x0001),
+ .bInterfaceClass = USB_CLASS_AUDIO,
+},
+
/* Miditech devices */
{
USB_DEVICE(0x4752, 0x0011),
*/
static int snd_usb_cm6206_boot_quirk(struct usb_device *dev)
{
- int err, reg;
+ int err = 0, reg;
int val[] = {0x2004, 0x3000, 0xf800, 0x143f, 0x0000, 0x3000};
for (reg = 0; reg < ARRAY_SIZE(val); reg++) {
$(OUTPUT)python/perf.so: $(PYRF_OBJS)
$(QUIET_GEN)CFLAGS='$(BASIC_CFLAGS)' $(PYTHON_WORD) util/setup.py \
- --quiet build_ext \
- --build-lib='$(OUTPUT)python' \
- --build-temp='$(OUTPUT)python/temp'
+ --quiet build_ext; \
+ mkdir -p $(OUTPUT)python && \
+ cp $(PYTHON_EXTBUILD_LIB)perf.so $(OUTPUT)python/
#
# No Perl scripts right now:
#
PYTHON_WORD := $(call shell-wordify,$(PYTHON))
- python-clean := $(PYTHON_WORD) util/setup.py clean \
- --build-lib='$(OUTPUT)python' \
- --build-temp='$(OUTPUT)python/temp'
+ # python extension build directories
+ PYTHON_EXTBUILD := $(OUTPUT)python_ext_build/
+ PYTHON_EXTBUILD_LIB := $(PYTHON_EXTBUILD)lib/
+ PYTHON_EXTBUILD_TMP := $(PYTHON_EXTBUILD)tmp/
+ export PYTHON_EXTBUILD_LIB PYTHON_EXTBUILD_TMP
+
+ python-clean := rm -rf $(PYTHON_EXTBUILD) $(OUTPUT)python/perf.so
ifdef NO_LIBPYTHON
$(call disable-python)
$(INSTALL) scripts/python/*.py -t '$(DESTDIR_SQ)$(perfexec_instdir_SQ)/scripts/python'
$(INSTALL) scripts/python/bin/* -t '$(DESTDIR_SQ)$(perfexec_instdir_SQ)/scripts/python/bin'
+install-python_ext:
+ $(PYTHON_WORD) util/setup.py --quiet install --root='/$(DESTDIR_SQ)'
+
install-doc:
$(MAKE) -C Documentation install
### Cleaning rules
clean:
- $(RM) $(OUTPUT){*.o,*/*.o,*/*/*.o,*/*/*/*.o,$(LIB_FILE),perf-archive}
+ $(RM) $(LIB_OBJS) $(BUILTIN_OBJS) $(LIB_FILE) $(OUTPUT)perf-archive $(OUTPUT)perf.o $(LANG_BINDINGS)
$(RM) $(ALL_PROGRAMS) perf
$(RM) *.spec *.pyc *.pyo */*.pyc */*.pyo $(OUTPUT)common-cmds.h TAGS tags cscope*
$(MAKE) -C Documentation/ clean
"-f",
"-m", "1024",
"-c", "1",
- "-e", "lock:lock_acquire:r",
- "-e", "lock:lock_acquired:r",
- "-e", "lock:lock_contended:r",
- "-e", "lock:lock_release:r",
+ "-e", "lock:lock_acquire",
+ "-e", "lock:lock_acquired",
+ "-e", "lock:lock_contended",
+ "-e", "lock:lock_release",
};
static int __cmd_record(int argc, const char **argv)
#include <sched.h>
#include <sys/mman.h>
-#define FD(e, x, y) (*(int *)xyarray__entry(e->fd, x, y))
-
enum write_mode_t {
WRITE_FORCE,
WRITE_APPEND
static int __cmd_record(int argc, const char **argv)
{
- int i;
struct stat st;
int flags;
int err;
for (;;) {
int hits = samples;
- int thread;
mmap_read_all();
waking++;
}
- if (done) {
- for (i = 0; i < evsel_list->cpus->nr; i++) {
- struct perf_evsel *pos;
-
- list_for_each_entry(pos, &evsel_list->entries, node) {
- for (thread = 0;
- thread < evsel_list->threads->nr;
- thread++)
- ioctl(FD(pos, i, thread),
- PERF_EVENT_IOC_DISABLE);
- }
- }
- }
+ if (done)
+ perf_evlist__disable(evsel_list);
}
if (quiet || signr == SIGUSR1)
{
if (!(self->sample_type & PERF_SAMPLE_CALLCHAIN)) {
if (sort__has_parent) {
- fprintf(stderr, "selected --sort parent, but no"
- " callchain data. Did you call"
- " perf record without -g?\n");
+ ui__warning("Selected --sort parent, but no "
+ "callchain data. Did you call "
+ "'perf record' without -g?\n");
return -EINVAL;
}
if (symbol_conf.use_callchain) {
- fprintf(stderr, "selected -g but no callchain data."
- " Did you call perf record without"
- " -g?\n");
+ ui__warning("Selected -g but no callchain data. Did "
+ "you call 'perf record' without -g?\n");
return -1;
}
} else if (!dont_use_callchains && callchain_param.mode != CHAIN_NONE &&
!symbol_conf.use_callchain) {
symbol_conf.use_callchain = true;
if (callchain_register_param(&callchain_param) < 0) {
- fprintf(stderr, "Can't register callchain"
- " params\n");
+ ui__warning("Can't register callchain "
+ "params.\n");
return -EINVAL;
}
}
.ordered_samples = true,
};
-static int read_events(void)
+static void read_events(bool destroy, struct perf_session **psession)
{
int err = -EINVAL;
struct perf_session *session = perf_session__new(input_name, O_RDONLY,
0, false, &event_ops);
if (session == NULL)
- return -ENOMEM;
+ die("No Memory");
if (perf_session__has_traces(session, "record -R")) {
err = perf_session__process_events(session, &event_ops);
+ if (err)
+ die("Failed to process events, error %d", err);
+
nr_events = session->hists.stats.nr_events[0];
nr_lost_events = session->hists.stats.total_lost;
nr_lost_chunks = session->hists.stats.nr_events[PERF_RECORD_LOST];
}
- perf_session__delete(session);
- return err;
+ if (destroy)
+ perf_session__delete(session);
+
+ if (psession)
+ *psession = session;
}
static void print_bad_events(void)
static void __cmd_lat(void)
{
struct rb_node *next;
+ struct perf_session *session;
setup_pager();
- read_events();
+ read_events(false, &session);
sort_lat();
printf("\n ---------------------------------------------------------------------------------------------------------------\n");
print_bad_events();
printf("\n");
+ perf_session__delete(session);
}
static struct trace_sched_handler map_ops = {
max_cpu = sysconf(_SC_NPROCESSORS_CONF);
setup_pager();
- read_events();
+ read_events(true, NULL);
print_bad_events();
}
test_calibrations();
- read_events();
+ read_events(true, NULL);
printf("nr_run_events: %ld\n", nr_run_events);
printf("nr_sleep_events: %ld\n", nr_sleep_events);
static const char * const sched_usage[] = {
- "perf sched [<options>] {record|latency|map|replay|trace}",
+ "perf sched [<options>] {record|latency|map|replay|script}",
NULL
};
int perf_config(config_fn_t fn, void *data)
{
int ret = 0, found = 0;
- char *repo_config = NULL;
const char *home = NULL;
/* Setting $PERF_CONFIG makes perf read _only_ the given config file. */
home = getenv("HOME");
if (perf_config_global() && home) {
char *user_config = strdup(mkpath("%s/.perfconfig", home));
- if (!access(user_config, R_OK)) {
- ret += perf_config_from_file(fn, user_config, data);
- found += 1;
+ struct stat st;
+
+ if (user_config == NULL) {
+ warning("Not enough memory to process %s/.perfconfig, "
+ "ignoring it.", home);
+ goto out;
}
- free(user_config);
- }
- repo_config = perf_pathdup("config");
- if (!access(repo_config, R_OK)) {
- ret += perf_config_from_file(fn, repo_config, data);
+ if (stat(user_config, &st) < 0)
+ goto out_free;
+
+ if (st.st_uid && (st.st_uid != geteuid())) {
+ warning("File %s not owned by current user or root, "
+ "ignoring it.", user_config);
+ goto out_free;
+ }
+
+ if (!st.st_size)
+ goto out_free;
+
+ ret += perf_config_from_file(fn, user_config, data);
found += 1;
+out_free:
+ free(user_config);
}
- free(repo_config);
+out:
if (found == 0)
return -1;
return ret;
return 0;
}
+void perf_evlist__disable(struct perf_evlist *evlist)
+{
+ int cpu, thread;
+ struct perf_evsel *pos;
+
+ for (cpu = 0; cpu < evlist->cpus->nr; cpu++) {
+ list_for_each_entry(pos, &evlist->entries, node) {
+ for (thread = 0; thread < evlist->threads->nr; thread++)
+ ioctl(FD(pos, cpu, thread), PERF_EVENT_IOC_DISABLE);
+ }
+ }
+}
+
int perf_evlist__alloc_pollfd(struct perf_evlist *evlist)
{
int nfds = evlist->cpus->nr * evlist->threads->nr * evlist->nr_entries;
int perf_evlist__mmap(struct perf_evlist *evlist, int pages, bool overwrite);
void perf_evlist__munmap(struct perf_evlist *evlist);
+void perf_evlist__disable(struct perf_evlist *evlist);
+
static inline void perf_evlist__set_maps(struct perf_evlist *evlist,
struct cpu_map *cpus,
struct thread_map *threads)
const char *name, bool is_kallsyms)
{
const size_t size = PATH_MAX;
- char *realname, *filename = malloc(size),
- *linkname = malloc(size), *targetname;
+ char *realname, *filename = zalloc(size),
+ *linkname = zalloc(size), *targetname;
int len, err = -1;
if (is_kallsyms) {
int build_id_cache__remove_s(const char *sbuild_id, const char *debugdir)
{
const size_t size = PATH_MAX;
- char *filename = malloc(size),
- *linkname = malloc(size);
+ char *filename = zalloc(size),
+ *linkname = zalloc(size);
int err = -1;
if (filename == NULL || linkname == NULL)
ret = -ENOMEM;
goto error;
}
- tev->point.module = strdup(module);
- if (tev->point.module == NULL) {
- ret = -ENOMEM;
- goto error;
+
+ if (module) {
+ tev->point.module = strdup(module);
+ if (tev->point.module == NULL) {
+ ret = -ENOMEM;
+ goto error;
+ }
}
+
tev->point.offset = pev->point.offset;
tev->point.retprobe = pev->point.retprobe;
tev->nargs = pev->nargs;
.tp_repr = (reprfunc)pyrf_throttle_event__repr,
};
+static char pyrf_lost_event__doc[] = PyDoc_STR("perf lost event object.");
+
+static PyMemberDef pyrf_lost_event__members[] = {
+ sample_members
+ member_def(lost_event, id, T_ULONGLONG, "event id"),
+ member_def(lost_event, lost, T_ULONGLONG, "number of lost events"),
+ { .name = NULL, },
+};
+
+static PyObject *pyrf_lost_event__repr(struct pyrf_event *pevent)
+{
+ PyObject *ret;
+ char *s;
+
+ if (asprintf(&s, "{ type: lost, id: %#" PRIx64 ", "
+ "lost: %#" PRIx64 " }",
+ pevent->event.lost.id, pevent->event.lost.lost) < 0) {
+ ret = PyErr_NoMemory();
+ } else {
+ ret = PyString_FromString(s);
+ free(s);
+ }
+ return ret;
+}
+
+static PyTypeObject pyrf_lost_event__type = {
+ PyVarObject_HEAD_INIT(NULL, 0)
+ .tp_name = "perf.lost_event",
+ .tp_basicsize = sizeof(struct pyrf_event),
+ .tp_flags = Py_TPFLAGS_DEFAULT|Py_TPFLAGS_BASETYPE,
+ .tp_doc = pyrf_lost_event__doc,
+ .tp_members = pyrf_lost_event__members,
+ .tp_repr = (reprfunc)pyrf_lost_event__repr,
+};
+
+static char pyrf_read_event__doc[] = PyDoc_STR("perf read event object.");
+
+static PyMemberDef pyrf_read_event__members[] = {
+ sample_members
+ member_def(read_event, pid, T_UINT, "event pid"),
+ member_def(read_event, tid, T_UINT, "event tid"),
+ { .name = NULL, },
+};
+
+static PyObject *pyrf_read_event__repr(struct pyrf_event *pevent)
+{
+ return PyString_FromFormat("{ type: read, pid: %u, tid: %u }",
+ pevent->event.read.pid,
+ pevent->event.read.tid);
+ /*
+ * FIXME: return the array of read values,
+ * making this method useful ;-)
+ */
+}
+
+static PyTypeObject pyrf_read_event__type = {
+ PyVarObject_HEAD_INIT(NULL, 0)
+ .tp_name = "perf.read_event",
+ .tp_basicsize = sizeof(struct pyrf_event),
+ .tp_flags = Py_TPFLAGS_DEFAULT|Py_TPFLAGS_BASETYPE,
+ .tp_doc = pyrf_read_event__doc,
+ .tp_members = pyrf_read_event__members,
+ .tp_repr = (reprfunc)pyrf_read_event__repr,
+};
+
+static char pyrf_sample_event__doc[] = PyDoc_STR("perf sample event object.");
+
+static PyMemberDef pyrf_sample_event__members[] = {
+ sample_members
+ member_def(perf_event_header, type, T_UINT, "event type"),
+ { .name = NULL, },
+};
+
+static PyObject *pyrf_sample_event__repr(struct pyrf_event *pevent)
+{
+ PyObject *ret;
+ char *s;
+
+ if (asprintf(&s, "{ type: sample }") < 0) {
+ ret = PyErr_NoMemory();
+ } else {
+ ret = PyString_FromString(s);
+ free(s);
+ }
+ return ret;
+}
+
+static PyTypeObject pyrf_sample_event__type = {
+ PyVarObject_HEAD_INIT(NULL, 0)
+ .tp_name = "perf.sample_event",
+ .tp_basicsize = sizeof(struct pyrf_event),
+ .tp_flags = Py_TPFLAGS_DEFAULT|Py_TPFLAGS_BASETYPE,
+ .tp_doc = pyrf_sample_event__doc,
+ .tp_members = pyrf_sample_event__members,
+ .tp_repr = (reprfunc)pyrf_sample_event__repr,
+};
+
static int pyrf_event__setup_types(void)
{
int err;
pyrf_mmap_event__type.tp_new =
pyrf_task_event__type.tp_new =
pyrf_comm_event__type.tp_new =
+ pyrf_lost_event__type.tp_new =
+ pyrf_read_event__type.tp_new =
+ pyrf_sample_event__type.tp_new =
pyrf_throttle_event__type.tp_new = PyType_GenericNew;
err = PyType_Ready(&pyrf_mmap_event__type);
+ if (err < 0)
+ goto out;
+ err = PyType_Ready(&pyrf_lost_event__type);
if (err < 0)
goto out;
err = PyType_Ready(&pyrf_task_event__type);
err = PyType_Ready(&pyrf_throttle_event__type);
if (err < 0)
goto out;
+ err = PyType_Ready(&pyrf_read_event__type);
+ if (err < 0)
+ goto out;
+ err = PyType_Ready(&pyrf_sample_event__type);
+ if (err < 0)
+ goto out;
out:
return err;
}
static PyTypeObject *pyrf_event__type[] = {
[PERF_RECORD_MMAP] = &pyrf_mmap_event__type,
- [PERF_RECORD_LOST] = &pyrf_mmap_event__type,
+ [PERF_RECORD_LOST] = &pyrf_lost_event__type,
[PERF_RECORD_COMM] = &pyrf_comm_event__type,
[PERF_RECORD_EXIT] = &pyrf_task_event__type,
[PERF_RECORD_THROTTLE] = &pyrf_throttle_event__type,
[PERF_RECORD_UNTHROTTLE] = &pyrf_throttle_event__type,
[PERF_RECORD_FORK] = &pyrf_task_event__type,
- [PERF_RECORD_READ] = &pyrf_mmap_event__type,
- [PERF_RECORD_SAMPLE] = &pyrf_mmap_event__type,
+ [PERF_RECORD_READ] = &pyrf_read_event__type,
+ [PERF_RECORD_SAMPLE] = &pyrf_sample_event__type,
};
static PyObject *pyrf_event__new(union perf_event *event)
from distutils.core import setup, Extension
from os import getenv
+from distutils.command.build_ext import build_ext as _build_ext
+from distutils.command.install_lib import install_lib as _install_lib
+
+class build_ext(_build_ext):
+ def finalize_options(self):
+ _build_ext.finalize_options(self)
+ self.build_lib = build_lib
+ self.build_temp = build_tmp
+
+class install_lib(_install_lib):
+ def finalize_options(self):
+ _install_lib.finalize_options(self)
+ self.build_dir = build_lib
+
+
cflags = ['-fno-strict-aliasing', '-Wno-write-strings']
cflags += getenv('CFLAGS', '').split()
+build_lib = getenv('PYTHON_EXTBUILD_LIB')
+build_tmp = getenv('PYTHON_EXTBUILD_TMP')
+
perf = Extension('perf',
sources = ['util/python.c', 'util/ctype.c', 'util/evlist.c',
'util/evsel.c', 'util/cpumap.c', 'util/thread_map.c',
author_email='acme@redhat.com',
license='GPLv2',
url='http://perf.wiki.kernel.org',
- ext_modules=[perf])
+ ext_modules=[perf],
+ cmdclass={'build_ext': build_ext, 'install_lib': install_lib})
dso->adjust_symbols = 0;
if (strncmp(dso->name, "/tmp/perf-", 10) == 0) {
+ struct stat st;
+
+ if (stat(dso->name, &st) < 0)
+ return -1;
+
+ if (st.st_uid && (st.st_uid != geteuid())) {
+ pr_warning("File %s not owned by current user or root, "
+ "ignoring it.\n", dso->name);
+ return -1;
+ }
+
ret = dso__load_perf_map(dso, map, filter);
dso->symtab_type = ret > 0 ? SYMTAB__JAVA_JIT :
SYMTAB__NOT_FOUND;
projects / mirror_ubuntu-bionic-kernel.git / commitdiff