Say yes here if you want to include support GPIO for pins on
the PCF50633 chip.
+config ABX500_CORE
+ bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
+ default y if ARCH_U300
+ help
+ Say yes here if you have the ABX500 Mixed Signal IC family
+ chips. This core driver expose register access functions.
+ Functionality specific drivers using these functions can
+ remain unchanged when IC changes. Binding of the functions to
+ actual register access is done by the IC core driver.
+
config AB3100_CORE
bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
- depends on I2C=y
+ depends on I2C=y && ABX500_CORE
default y if ARCH_U300
help
Select this to enable the AB3100 Mixed Signal IC core
obj-$(CONFIG_MFD_PCF50633) += pcf50633-core.o
obj-$(CONFIG_PCF50633_ADC) += pcf50633-adc.o
obj-$(CONFIG_PCF50633_GPIO) += pcf50633-gpio.o
+obj-$(CONFIG_ABX500_CORE) += abx500-core.o
obj-$(CONFIG_AB3100_CORE) += ab3100-core.o
obj-$(CONFIG_AB3100_OTP) += ab3100-otp.o
obj-$(CONFIG_AB4500_CORE) += ab4500-core.o
* The AB3100 is usually assigned address 0x48 (7-bit)
* The chip is defined in the platform i2c_board_data section.
*/
-
-u8 ab3100_get_chip_type(struct ab3100 *ab3100)
+static int ab3100_get_chip_id(struct device *dev)
{
- u8 chip = ABUNKNOWN;
-
- switch (ab3100->chip_id & 0xf0) {
- case 0xa0:
- chip = AB3000;
- break;
- case 0xc0:
- chip = AB3100;
- break;
- }
- return chip;
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+
+ return (int)ab3100->chip_id;
}
-EXPORT_SYMBOL(ab3100_get_chip_type);
-int ab3100_set_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 regval)
+static int ab3100_set_register_interruptible(struct ab3100 *ab3100,
+ u8 reg, u8 regval)
{
u8 regandval[2] = {reg, regval};
int err;
mutex_unlock(&ab3100->access_mutex);
return err;
}
-EXPORT_SYMBOL(ab3100_set_register_interruptible);
+static int set_register_interruptible(struct device *dev,
+ u8 bank, u8 reg, u8 value)
+{
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+
+ return ab3100_set_register_interruptible(ab3100, reg, value);
+}
/*
* The test registers exist at an I2C bus address up one
return err;
}
-
-int ab3100_get_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 *regval)
+static int ab3100_get_register_interruptible(struct ab3100 *ab3100,
+ u8 reg, u8 *regval)
{
int err;
mutex_unlock(&ab3100->access_mutex);
return err;
}
-EXPORT_SYMBOL(ab3100_get_register_interruptible);
+static int get_register_interruptible(struct device *dev, u8 bank, u8 reg,
+ u8 *value)
+{
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+
+ return ab3100_get_register_interruptible(ab3100, reg, value);
+}
-int ab3100_get_register_page_interruptible(struct ab3100 *ab3100,
+static int ab3100_get_register_page_interruptible(struct ab3100 *ab3100,
u8 first_reg, u8 *regvals, u8 numregs)
{
int err;
mutex_unlock(&ab3100->access_mutex);
return err;
}
-EXPORT_SYMBOL(ab3100_get_register_page_interruptible);
+static int get_register_page_interruptible(struct device *dev, u8 bank,
+ u8 first_reg, u8 *regvals, u8 numregs)
+{
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+
+ return ab3100_get_register_page_interruptible(ab3100,
+ first_reg, regvals, numregs);
+}
-int ab3100_mask_and_set_register_interruptible(struct ab3100 *ab3100,
+static int ab3100_mask_and_set_register_interruptible(struct ab3100 *ab3100,
u8 reg, u8 andmask, u8 ormask)
{
u8 regandval[2] = {reg, 0};
mutex_unlock(&ab3100->access_mutex);
return err;
}
-EXPORT_SYMBOL(ab3100_mask_and_set_register_interruptible);
+static int mask_and_set_register_interruptible(struct device *dev, u8 bank,
+ u8 reg, u8 bitmask, u8 bitvalues)
+{
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
+
+ return ab3100_mask_and_set_register_interruptible(ab3100,
+ reg, bitmask, (bitmask & bitvalues));
+}
/*
* Register a simple callback for handling any AB3100 events.
EXPORT_SYMBOL(ab3100_event_unregister);
-int ab3100_event_registers_startup_state_get(struct ab3100 *ab3100,
- u32 *fatevent)
+static int ab3100_event_registers_startup_state_get(struct device *dev,
+ u8 *event)
{
+ struct ab3100 *ab3100 = dev_get_drvdata(dev->parent);
if (!ab3100->startup_events_read)
return -EAGAIN; /* Try again later */
- *fatevent = ab3100->startup_events;
+ memcpy(event, ab3100->startup_events, 3);
return 0;
}
-EXPORT_SYMBOL(ab3100_event_registers_startup_state_get);
+
+static struct abx500_ops ab3100_ops = {
+ .get_chip_id = ab3100_get_chip_id,
+ .set_register = set_register_interruptible,
+ .get_register = get_register_interruptible,
+ .get_register_page = get_register_page_interruptible,
+ .set_register_page = NULL,
+ .mask_and_set_register = mask_and_set_register_interruptible,
+ .event_registers_startup_state_get =
+ ab3100_event_registers_startup_state_get,
+ .startup_irq_enabled = NULL,
+};
/*
* This is a threaded interrupt handler so we can make some
event_regs[2];
if (!ab3100->startup_events_read) {
- ab3100->startup_events = fatevent;
+ ab3100->startup_events[0] = event_regs[0];
+ ab3100->startup_events[1] = event_regs[1];
+ ab3100->startup_events[2] = event_regs[2];
ab3100->startup_events_read = true;
}
/*
dev_warn(ab3100->dev,
"AB3100 P1E variant detected, "
"forcing chip to 32KHz\n");
- err = ab3100_set_test_register_interruptible(ab3100, 0x02, 0x08);
+ err = ab3100_set_test_register_interruptible(ab3100,
+ 0x02, 0x08);
}
exit_no_setup:
if (err)
goto exit_no_irq;
+ err = abx500_register_ops(&client->dev, &ab3100_ops);
+ if (err)
+ goto exit_no_ops;
+
/* Set parent and a pointer back to the container in device data */
for (i = 0; i < ARRAY_SIZE(ab3100_platform_devs); i++) {
ab3100_platform_devs[i]->dev.parent =
return 0;
+ exit_no_ops:
exit_no_irq:
exit_no_setup:
i2c_unregister_device(ab3100->testreg_client);
/**
* struct ab3100_otp
* @dev containing device
- * @ab3100 a pointer to the parent ab3100 device struct
* @locked whether the OTP is locked, after locking, no more bits
* can be changed but before locking it is still possible
* to change bits from 1->0.
*/
struct ab3100_otp {
struct device *dev;
- struct ab3100 *ab3100;
bool locked;
u32 freq;
bool paf;
static int __init ab3100_otp_read(struct ab3100_otp *otp)
{
- struct ab3100 *ab = otp->ab3100;
u8 otpval[8];
u8 otpp;
int err;
- err = ab3100_get_register_interruptible(ab, AB3100_OTPP, &otpp);
+ err = abx500_get_register_interruptible(otp->dev, 0,
+ AB3100_OTPP, &otpp);
if (err) {
dev_err(otp->dev, "unable to read OTPP register\n");
return err;
}
- err = ab3100_get_register_page_interruptible(ab, AB3100_OTP0,
- otpval, 8);
+ err = abx500_get_register_page_interruptible(otp->dev, 0,
+ AB3100_OTP0, otpval, 8);
if (err) {
dev_err(otp->dev, "unable to read OTP register page\n");
return err;
otp->dev = &pdev->dev;
/* Replace platform data coming in with a local struct */
- otp->ab3100 = platform_get_drvdata(pdev);
platform_set_drvdata(pdev, otp);
err = ab3100_otp_read(otp);
--- /dev/null
+/*
+ * Copyright (C) 2007-2010 ST-Ericsson
+ * License terms: GNU General Public License (GPL) version 2
+ * Register access functions for the ABX500 Mixed Signal IC family.
+ * Author: Mattias Wallin <mattias.wallin@stericsson.com>
+ */
+
+#include <linux/list.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/mfd/abx500.h>
+
+static LIST_HEAD(abx500_list);
+
+struct abx500_device_entry {
+ struct list_head list;
+ struct abx500_ops ops;
+ struct device *dev;
+};
+
+static void lookup_ops(struct device *dev, struct abx500_ops **ops)
+{
+ struct abx500_device_entry *dev_entry;
+
+ *ops = NULL;
+ list_for_each_entry(dev_entry, &abx500_list, list) {
+ if (dev_entry->dev == dev) {
+ *ops = &dev_entry->ops;
+ return;
+ }
+ }
+}
+
+int abx500_register_ops(struct device *dev, struct abx500_ops *ops)
+{
+ struct abx500_device_entry *dev_entry;
+
+ dev_entry = kzalloc(sizeof(struct abx500_device_entry), GFP_KERNEL);
+ if (IS_ERR(dev_entry)) {
+ dev_err(dev, "register_ops kzalloc failed");
+ return -ENOMEM;
+ }
+ dev_entry->dev = dev;
+ memcpy(&dev_entry->ops, ops, sizeof(struct abx500_ops));
+
+ list_add_tail(&dev_entry->list, &abx500_list);
+ return 0;
+}
+EXPORT_SYMBOL(abx500_register_ops);
+
+void abx500_remove_ops(struct device *dev)
+{
+ struct abx500_device_entry *dev_entry, *tmp;
+
+ list_for_each_entry_safe(dev_entry, tmp, &abx500_list, list)
+ {
+ if (dev_entry->dev == dev) {
+ list_del(&dev_entry->list);
+ kfree(dev_entry);
+ }
+ }
+}
+EXPORT_SYMBOL(abx500_remove_ops);
+
+int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
+ u8 value)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->set_register != NULL))
+ return ops->set_register(dev, bank, reg, value);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_set_register_interruptible);
+
+int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,
+ u8 *value)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->get_register != NULL))
+ return ops->get_register(dev, bank, reg, value);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_get_register_interruptible);
+
+int abx500_get_register_page_interruptible(struct device *dev, u8 bank,
+ u8 first_reg, u8 *regvals, u8 numregs)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->get_register_page != NULL))
+ return ops->get_register_page(dev, bank,
+ first_reg, regvals, numregs);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_get_register_page_interruptible);
+
+int abx500_mask_and_set_register_interruptible(struct device *dev, u8 bank,
+ u8 reg, u8 bitmask, u8 bitvalues)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->mask_and_set_register != NULL))
+ return ops->mask_and_set_register(dev, bank,
+ reg, bitmask, bitvalues);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_mask_and_set_register_interruptible);
+
+int abx500_get_chip_id(struct device *dev)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->get_chip_id != NULL))
+ return ops->get_chip_id(dev);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_get_chip_id);
+
+int abx500_event_registers_startup_state_get(struct device *dev, u8 *event)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->event_registers_startup_state_get != NULL))
+ return ops->event_registers_startup_state_get(dev, event);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_event_registers_startup_state_get);
+
+int abx500_startup_irq_enabled(struct device *dev, unsigned int irq)
+{
+ struct abx500_ops *ops;
+
+ lookup_ops(dev->parent, &ops);
+ if ((ops != NULL) && (ops->startup_irq_enabled != NULL))
+ return ops->startup_irq_enabled(dev, irq);
+ else
+ return -ENOTSUPP;
+}
+EXPORT_SYMBOL(abx500_startup_irq_enabled);
+
+MODULE_AUTHOR("Mattias Wallin <mattias.wallin@stericsson.com>");
+MODULE_DESCRIPTION("ABX500 core driver");
+MODULE_LICENSE("GPL");
* struct ab3100_regulator
* A struct passed around the individual regulator functions
* @platform_device: platform device holding this regulator
- * @ab3100: handle to the AB3100 parent chip
+ * @dev: handle to the device
* @plfdata: AB3100 platform data passed in at probe time
* @regreg: regulator register number in the AB3100
* @fixed_voltage: a fixed voltage for this regulator, if this
*/
struct ab3100_regulator {
struct regulator_dev *rdev;
- struct ab3100 *ab3100;
+ struct device *dev;
struct ab3100_platform_data *plfdata;
u8 regreg;
int fixed_voltage;
int err;
u8 regval;
- err = ab3100_get_register_interruptible(abreg->ab3100, abreg->regreg,
+ err = abx500_get_register_interruptible(abreg->dev, 0, abreg->regreg,
®val);
if (err) {
dev_warn(®->dev, "failed to get regid %d value\n",
regval |= AB3100_REG_ON_MASK;
- err = ab3100_set_register_interruptible(abreg->ab3100, abreg->regreg,
+ err = abx500_set_register_interruptible(abreg->dev, 0, abreg->regreg,
regval);
if (err) {
dev_warn(®->dev, "failed to set regid %d value\n",
if (abreg->regreg == AB3100_LDO_D) {
dev_info(®->dev, "disabling LDO D - shut down system\n");
/* Setting LDO D to 0x00 cuts the power to the SoC */
- return ab3100_set_register_interruptible(abreg->ab3100,
+ return abx500_set_register_interruptible(abreg->dev, 0,
AB3100_LDO_D, 0x00U);
}
/*
* All other regulators are handled here
*/
- err = ab3100_get_register_interruptible(abreg->ab3100, abreg->regreg,
+ err = abx500_get_register_interruptible(abreg->dev, 0, abreg->regreg,
®val);
if (err) {
dev_err(®->dev, "unable to get register 0x%x\n",
return err;
}
regval &= ~AB3100_REG_ON_MASK;
- return ab3100_set_register_interruptible(abreg->ab3100, abreg->regreg,
+ return abx500_set_register_interruptible(abreg->dev, 0, abreg->regreg,
regval);
}
u8 regval;
int err;
- err = ab3100_get_register_interruptible(abreg->ab3100, abreg->regreg,
+ err = abx500_get_register_interruptible(abreg->dev, 0, abreg->regreg,
®val);
if (err) {
dev_err(®->dev, "unable to get register 0x%x\n",
* For variable types, read out setting and index into
* supplied voltage list.
*/
- err = ab3100_get_register_interruptible(abreg->ab3100,
+ err = abx500_get_register_interruptible(abreg->dev, 0,
abreg->regreg, ®val);
if (err) {
dev_warn(®->dev,
if (bestindex < 0)
return bestindex;
- err = ab3100_get_register_interruptible(abreg->ab3100,
+ err = abx500_get_register_interruptible(abreg->dev, 0,
abreg->regreg, ®val);
if (err) {
dev_warn(®->dev,
regval &= ~0xE0;
regval |= (bestindex << 5);
- err = ab3100_set_register_interruptible(abreg->ab3100,
+ err = abx500_set_register_interruptible(abreg->dev, 0,
abreg->regreg, regval);
if (err)
dev_warn(®->dev, "failed to set regulator register %02x\n",
/* LDO E and BUCK have special suspend voltages you can set */
bestindex = ab3100_get_best_voltage_index(reg, uV, uV);
- err = ab3100_get_register_interruptible(abreg->ab3100,
+ err = abx500_get_register_interruptible(abreg->dev, 0,
targetreg, ®val);
if (err) {
dev_warn(®->dev,
regval &= ~0xE0;
regval |= (bestindex << 5);
- err = ab3100_set_register_interruptible(abreg->ab3100,
+ err = abx500_set_register_interruptible(abreg->dev, 0,
targetreg, regval);
if (err)
dev_warn(®->dev, "failed to set regulator register %02x\n",
static int __devinit ab3100_regulators_probe(struct platform_device *pdev)
{
struct ab3100_platform_data *plfdata = pdev->dev.platform_data;
- struct ab3100 *ab3100 = platform_get_drvdata(pdev);
int err = 0;
u8 data;
int i;
/* Check chip state */
- err = ab3100_get_register_interruptible(ab3100,
+ err = abx500_get_register_interruptible(&pdev->dev, 0,
AB3100_LDO_D, &data);
if (err) {
dev_err(&pdev->dev, "could not read initial status of LDO_D\n");
/* Set up regulators */
for (i = 0; i < ARRAY_SIZE(ab3100_reg_init_order); i++) {
- err = ab3100_set_register_interruptible(ab3100,
+ err = abx500_set_register_interruptible(&pdev->dev, 0,
ab3100_reg_init_order[i],
plfdata->reg_initvals[i]);
if (err) {
* see what it looks like for a certain machine, go
* into the machine I2C setup.
*/
- reg->ab3100 = ab3100;
+ reg->dev = &pdev->dev;
reg->plfdata = plfdata;
/*
*/
static int ab3100_rtc_set_mmss(struct device *dev, unsigned long secs)
{
- struct ab3100 *ab3100_data = dev_get_drvdata(dev);
u8 regs[] = {AB3100_TI0, AB3100_TI1, AB3100_TI2,
AB3100_TI3, AB3100_TI4, AB3100_TI5};
unsigned char buf[6];
buf[5] = (fat_time >> 40) & 0xFF;
for (i = 0; i < 6; i++) {
- err = ab3100_set_register_interruptible(ab3100_data,
+ err = abx500_set_register_interruptible(dev, 0,
regs[i], buf[i]);
if (err)
return err;
}
/* Set the flag to mark that the clock is now set */
- return ab3100_mask_and_set_register_interruptible(ab3100_data,
+ return abx500_mask_and_set_register_interruptible(dev, 0,
AB3100_RTC,
- 0xFE, 0x01);
+ 0x01, 0x01);
}
static int ab3100_rtc_read_time(struct device *dev, struct rtc_time *tm)
{
- struct ab3100 *ab3100_data = dev_get_drvdata(dev);
unsigned long time;
u8 rtcval;
int err;
- err = ab3100_get_register_interruptible(ab3100_data,
+ err = abx500_get_register_interruptible(dev, 0,
AB3100_RTC, &rtcval);
if (err)
return err;
u8 buf[6];
/* Read out time registers */
- err = ab3100_get_register_page_interruptible(ab3100_data,
+ err = abx500_get_register_page_interruptible(dev, 0,
AB3100_TI0,
buf, 6);
if (err != 0)
static int ab3100_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alarm)
{
- struct ab3100 *ab3100_data = dev_get_drvdata(dev);
unsigned long time;
u64 fat_time;
u8 buf[6];
int err;
/* Figure out if alarm is enabled or not */
- err = ab3100_get_register_interruptible(ab3100_data,
+ err = abx500_get_register_interruptible(dev, 0,
AB3100_RTC, &rtcval);
if (err)
return err;
/* No idea how this could be represented */
alarm->pending = 0;
/* Read out alarm registers, only 4 bytes */
- err = ab3100_get_register_page_interruptible(ab3100_data,
+ err = abx500_get_register_page_interruptible(dev, 0,
AB3100_AL0, buf, 4);
if (err)
return err;
static int ab3100_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alarm)
{
- struct ab3100 *ab3100_data = dev_get_drvdata(dev);
u8 regs[] = {AB3100_AL0, AB3100_AL1, AB3100_AL2, AB3100_AL3};
unsigned char buf[4];
unsigned long secs;
/* Set the alarm */
for (i = 0; i < 4; i++) {
- err = ab3100_set_register_interruptible(ab3100_data,
+ err = abx500_set_register_interruptible(dev, 0,
regs[i], buf[i]);
if (err)
return err;
}
/* Then enable the alarm */
- return ab3100_mask_and_set_register_interruptible(ab3100_data,
- AB3100_RTC, ~(1 << 2),
+ return abx500_mask_and_set_register_interruptible(dev, 0,
+ AB3100_RTC, (1 << 2),
alarm->enabled << 2);
}
static int ab3100_rtc_irq_enable(struct device *dev, unsigned int enabled)
{
- struct ab3100 *ab3100_data = dev_get_drvdata(dev);
-
/*
* It's not possible to enable/disable the alarm IRQ for this RTC.
* It does not actually trigger any IRQ: instead its only function is
* and need to be handled there instead.
*/
if (enabled)
- return ab3100_mask_and_set_register_interruptible(ab3100_data,
- AB3100_RTC, ~(1 << 2),
+ return abx500_mask_and_set_register_interruptible(dev, 0,
+ AB3100_RTC, (1 << 2),
1 << 2);
else
- return ab3100_mask_and_set_register_interruptible(ab3100_data,
- AB3100_RTC, ~(1 << 2),
+ return abx500_mask_and_set_register_interruptible(dev, 0,
+ AB3100_RTC, (1 << 2),
0);
}
int err;
u8 regval;
struct rtc_device *rtc;
- struct ab3100 *ab3100_data = platform_get_drvdata(pdev);
/* The first RTC register needs special treatment */
- err = ab3100_get_register_interruptible(ab3100_data,
+ err = abx500_get_register_interruptible(&pdev->dev, 0,
AB3100_RTC, ®val);
if (err) {
dev_err(&pdev->dev, "unable to read RTC register\n");
* This bit remains until RTC power is lost.
*/
regval = 1 | RTC_SETTING;
- err = ab3100_set_register_interruptible(ab3100_data,
+ err = abx500_set_register_interruptible(&pdev->dev, 0,
AB3100_RTC, regval);
/* Ignore any error on this write */
}
* License terms: GNU General Public License (GPL) version 2
* AB3100 core access functions
* Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ * ABX500 core access functions.
+ * The abx500 interface is used for the Analog Baseband chip
+ * ab3100, ab3550, ab5500 and possibly comming. It is not used for
+ * ab4500 and ab8500 since they are another family of chip.
+ *
+ * Author: Mattias Wallin <mattias.wallin@stericsson.com>
+ * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
+ * Author: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
*/
#include <linux/device.h>
#include <linux/regulator/machine.h>
-#ifndef MFD_AB3100_H
-#define MFD_AB3100_H
+#ifndef MFD_ABX500_H
+#define MFD_ABX500_H
-#define ABUNKNOWN 0
-#define AB3000 1
-#define AB3100 2
+#define AB3100_P1A 0xc0
+#define AB3100_P1B 0xc1
+#define AB3100_P1C 0xc2
+#define AB3100_P1D 0xc3
+#define AB3100_P1E 0xc4
+#define AB3100_P1F 0xc5
+#define AB3100_P1G 0xc6
+#define AB3100_R2A 0xc7
+#define AB3100_R2B 0xc8
+#define AB3550_P1A 0x10
+#define AB5500_1_0 0x20
+#define AB5500_2_0 0x21
+#define AB5500_2_1 0x22
/*
* AB3100, EVENTA1, A2 and A3 event register flags
char chip_name[32];
u8 chip_id;
struct blocking_notifier_head event_subscribers;
- u32 startup_events;
+ u8 startup_events[3];
bool startup_events_read;
};
int external_voltage;
};
-int ab3100_set_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 regval);
-int ab3100_get_register_interruptible(struct ab3100 *ab3100, u8 reg, u8 *regval);
-int ab3100_get_register_page_interruptible(struct ab3100 *ab3100,
- u8 first_reg, u8 *regvals, u8 numregs);
-int ab3100_mask_and_set_register_interruptible(struct ab3100 *ab3100,
- u8 reg, u8 andmask, u8 ormask);
-u8 ab3100_get_chip_type(struct ab3100 *ab3100);
int ab3100_event_register(struct ab3100 *ab3100,
struct notifier_block *nb);
int ab3100_event_unregister(struct ab3100 *ab3100,
struct notifier_block *nb);
-int ab3100_event_registers_startup_state_get(struct ab3100 *ab3100,
- u32 *fatevent);
+/* AB3550, STR register flags */
+#define AB3550_STR_ONSWA (0x01)
+#define AB3550_STR_ONSWB (0x02)
+#define AB3550_STR_ONSWC (0x04)
+#define AB3550_STR_DCIO (0x08)
+#define AB3550_STR_BOOT_MODE (0x10)
+#define AB3550_STR_SIM_OFF (0x20)
+#define AB3550_STR_BATT_REMOVAL (0x40)
+#define AB3550_STR_VBUS (0x80)
+
+/* Interrupt mask registers */
+#define AB3550_IMR1 0x29
+#define AB3550_IMR2 0x2a
+#define AB3550_IMR3 0x2b
+#define AB3550_IMR4 0x2c
+#define AB3550_IMR5 0x2d
+
+enum ab3550_devid {
+ AB3550_DEVID_ADC,
+ AB3550_DEVID_DAC,
+ AB3550_DEVID_LEDS,
+ AB3550_DEVID_POWER,
+ AB3550_DEVID_REGULATORS,
+ AB3550_DEVID_SIM,
+ AB3550_DEVID_UART,
+ AB3550_DEVID_RTC,
+ AB3550_DEVID_CHARGER,
+ AB3550_DEVID_FUELGAUGE,
+ AB3550_DEVID_VIBRATOR,
+ AB3550_DEVID_CODEC,
+ AB3550_NUM_DEVICES,
+};
+
+/**
+ * struct abx500_init_setting
+ * Initial value of the registers for driver to use during setup.
+ */
+struct abx500_init_settings {
+ u8 bank;
+ u8 reg;
+ u8 setting;
+};
+
+/**
+ * struct ab3550_platform_data
+ * Data supplied to initialize board connections to the AB3550
+ */
+struct ab3550_platform_data {
+ struct {unsigned int base; unsigned int count; } irq;
+ void *dev_data[AB3550_NUM_DEVICES];
+ size_t dev_data_sz[AB3550_NUM_DEVICES];
+ struct abx500_init_settings *init_settings;
+ unsigned int init_settings_sz;
+};
+
+int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
+ u8 value);
+int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,
+ u8 *value);
+int abx500_get_register_page_interruptible(struct device *dev, u8 bank,
+ u8 first_reg, u8 *regvals, u8 numregs);
+int abx500_set_register_page_interruptible(struct device *dev, u8 bank,
+ u8 first_reg, u8 *regvals, u8 numregs);
+/**
+ * abx500_mask_and_set_register_inerruptible() - Modifies selected bits of a
+ * target register
+ *
+ * @dev: The AB sub device.
+ * @bank: The i2c bank number.
+ * @bitmask: The bit mask to use.
+ * @bitvalues: The new bit values.
+ *
+ * Updates the value of an AB register:
+ * value -> ((value & ~bitmask) | (bitvalues & bitmask))
+ */
+int abx500_mask_and_set_register_interruptible(struct device *dev, u8 bank,
+ u8 reg, u8 bitmask, u8 bitvalues);
+int abx500_get_chip_id(struct device *dev);
+int abx500_event_registers_startup_state_get(struct device *dev, u8 *event);
+int abx500_startup_irq_enabled(struct device *dev, unsigned int irq);
+
+struct abx500_ops {
+ int (*get_chip_id) (struct device *);
+ int (*get_register) (struct device *, u8, u8, u8 *);
+ int (*set_register) (struct device *, u8, u8, u8);
+ int (*get_register_page) (struct device *, u8, u8, u8 *, u8);
+ int (*set_register_page) (struct device *, u8, u8, u8 *, u8);
+ int (*mask_and_set_register) (struct device *, u8, u8, u8, u8);
+ int (*event_registers_startup_state_get) (struct device *, u8 *);
+ int (*startup_irq_enabled) (struct device *, unsigned int);
+};
+
+int abx500_register_ops(struct device *core_dev, struct abx500_ops *ops);
#endif
projects / mirror_ubuntu-zesty-kernel.git / commitdiff