Sergei Shtylyov [Wed, 29 Sep 2010 06:54:29 +0000 (09:54 +0300)]
USB: MUSB: fix kernel WARNING/oops when unloading module in OTG mode
Since commit 461972d8a4c94bc44f11a13046041c78a7cf18dd (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable <stable@kernel.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.
The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
USB: add platform glue driver for FSL USB DR controller
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OpenDCC project is developing a new hardware. This patch adds its
PID to the list of known FTDI devices. The PID can be found at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
Add empty functions for get/put transceiver functions too, so that
drivers that optionally use them can call them without worrying that
they might not exist, eliminating ifdefs.
This patch will only enable AUTOCLEAR if our endpoint's
FIFO was configured with double buffering support. Note
this is not a complete fix, double buffered case still
doesn't work always, but that hasn't been working for
quite some time. Other than reverting the entire commit
and breaking testusb with double buffered case again,
I decided it was better to fix the single buffered case
and spend more time fixing double buffered case properly.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ming Lei [Fri, 24 Sep 2010 10:44:14 +0000 (13:44 +0300)]
usb: musb: gadget: fix ZLP sending in musb_g_tx(v1)
This patch fixes the problem reported by Sergei:
>how come? we need to send ZLP before giving back the request.
>Well, look at the code ionce again. We need to send ZLP *after*
>request->actual == request->length, but as the check is inserted
>after the ZLP send, ZLP *may* be sent once the first DMA completes,
>not the last.
The patch also has been discussed on the link below:
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reported-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Fri, 24 Sep 2010 10:44:12 +0000 (13:44 +0300)]
usb: musb: gadget: kill unreachable code in musb_g_rx()
musb_g_rx() always returns if next_request() call yields NULL, so the DBG()
near the function's end can never be invoked. Remove it along with unneeded
'return'; also remove the duplicate 'request' check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bob Liu [Fri, 24 Sep 2010 10:44:07 +0000 (13:44 +0300)]
usb: musb: Change to direct addr in context save/restore
Since not all platforms are using the same offset 0x10 in
musb_save/restore_context() eg Blackfin the offset is 0x40,
Change the indexed address to direct.
Signed-off-by: Bob Liu <lliubbo@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: musb: host: unmap the buffer for PIO data transfers
The USB stack maps the buffer for DMA if the controller supports DMA.
MUSB controller can perform DMA as well as PIO transfers.
The buffer needs to be unmapped before CPU can perform
PIO data transfers.
Export unmap_urb_for_dma() so that drivers can perform
the DMA unmapping in a sane way.
Signed-off-by: Maulik Mankad <x0082077@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ming Lei [Fri, 24 Sep 2010 10:44:04 +0000 (13:44 +0300)]
usb: musb: support ISO high bandwidth for gadget mode
This patch has been tested OK on beagle B5 board and
use usbtest #15 and #16 as testcase.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Anand Gadiyar <gadiyar@ti.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Fri, 24 Sep 2010 10:44:02 +0000 (13:44 +0300)]
USB: musb: make DBG() calls actually depend on CONFIG_USB_MUSB_DEBUG
Enabling CONFIG_USB_MUSB_DEBUG option causes -DDEBUG to be added to gcc's
command line, however the DBG() macro doesn't depend on DEBUG, so that the
debugging messages get printed regardless of the option, and I don't think
that this was intended. Get rid of otherwise unused xprintk() macro and make
DBG() macro directly call pr_debug() which only results in the actual code
generated if DEBUG is defined.
This change makes musb_hdrc.o ~30% less in size with CONFIG_USB_MUSB_DEBUG
disabled (in host mode).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Meywa-Denki/Kayac YUREX is a leg-shakes sensor device.
See http://bbu.kayac.com/en/about/ for further information.
This driver support read/write the leg-shakes counter in the device
via a device file /dev/yurex[0-9]*.
Matthew Wilcox [Thu, 7 Oct 2010 11:05:23 +0000 (13:05 +0200)]
USB: Add UAS driver
USB Attached SCSI is a new protocol specified jointly by the SCSI T10
committee and the USB Implementors Forum.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
[mina86@mina86.com: updated to use new USB_ prefix] Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Thu, 7 Oct 2010 11:05:22 +0000 (13:05 +0200)]
USB: Move USB Storage definitions to their own header file
The libusual header file is hard to use from code that isn't part
of libusual. As the comment suggests, these definitions are moved to
their own header file, paralleling other USB classes.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Cc: Alan Stern <stern@rowland.harvard.edu>
[mina86@mina86.com: updated to use USB_ prefix and added #include guard] Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0000000..d7fc910
USB: qcserial: Enable Diagnostics Monitor and GPS ports on Gobi 2000
this patch to qcserial.c enables the Diagnostics Monitor
and NMEA GPS ports on Qualcomm Gobi 2000 devices.
A Gobi 2000 device will provide 3 serial ports:
# /dev/ttyUSB0 -> Diagnostics
# /dev/ttyUSB1 -> 3G Modem
# /dev/ttyUSB2 -> NMEA GPS port
* The Diagnostics Monitor uses Qualcomm's DM protocol; I used
libqcdm (ModemManager) to talk to it, found it working, but at
least DM commands 12 and 64 are not implemented on my device
(Gobi 2000 built into Thinkpad x100e).
* Functionality of the 3G Modem port remains unchanged.
* The GPS port and how to enable it has been confirmed now in the
Gobi 3000 source code at:
https://www.codeaurora.org/patches/quic/gobi/
Enable/disable GPS via:
echo "\$GPS_START" > /dev/ttyUSB2
# use GPS
echo "\$GPS_STOP" > /dev/ttyUSB2
Signed-off-by: Matthias G. Eckermann <mge@arcor.de>
In usb_cdc_ncm_dpe32 the fields are 32 bit long and according
to usb style (hungarian notation) should be called dwDatagramIndex
and dwDatagramLength (see CDC NCM subclass spec, 3.3.2). Actually,
they were called wDatagramIndex, wDatagramLength.
RTS and DTR should not be modified based on CRTSCTS when calling
set_termios.
Modem control lines are raised at port open by the tty layer and should stay
raised regardless of whether hardware flow control is enabled or not.
This is in conformance with the way serial ports work today and many
applications depend on this behaviour to be able to talk to hardware
implementing hardware flow control (without the applications actually using
it).
Hardware which expects different behaviour on these lines can always
use TIOCMSET/TIOCMBI[SC] after port open to change them.
Reported-by: Daniel Mack <daniel@caiaq.de> Reported-by: Dave Mielke <dave@mielke.cc> Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: cdc.h: ncm: add missed constants and structures
Make a dedicated structure for datagram pointer entry. There is no
explicit declaration in the spec, but it's used by the host
implementation and makes the structure more clear.
USB: option: Add new ONDA vendor id and product id for ONDA MT825UP
This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
usb: omap: ohci: Missing driver unregister in module exit
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms. The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Alan Stern [Mon, 13 Sep 2010 14:43:25 +0000 (10:43 -0400)]
USB: teach "devices" file about Wireless and SuperSpeed USB
The /sys/kernel/debug/usb/devices file doesn't know about Wireless or
SuperSpeed USB. This patch (as1416b) teaches it, and updates the
Documentation/usb/proc_sub_info.txt file accordingly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Vrabel <david.vrabel@csr.com> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile error on usb/host/isp1362-hcd:
drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’:
drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function)
The problem is when the CONFIG_USB_OTG option is enabled.
ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code
besides the portion defined in isp1362_hub_control.
So I think that maybe USB OTG support is not needed/supported.
This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roger Quadros [Wed, 8 Sep 2010 10:48:44 +0000 (13:48 +0300)]
usb gadget: composite: prevent OOPS for non-standard control request
The composite gadget will OOPS if the host sends a control request
targetted to an interface of an un-configured composite device. This patch
prevents this.
The OOPS was observed during WHQL USB CV tests. With this patch, the device
STALLs as per requirement.
Failing test case: From host do the following. I used libusb-1.0
1) Set configuration to zero.
libusb_control_transfer(device_handle,
0, /* standard OUT */
0x9, /* setConfiguration */
0, 0, NULL, 0, 0);
2) Query current configuratioan.
libusb_control_transfer(device_handle,
0x80, /* standard IN*/
0x8, /* getConfiguration */
0, 0, data, 1, 0);
3) Send the non-standard ctrl transfer targetted to interface
libusb_control_transfer(device_handle,
0x81, /* standard IN to interface*/
0x6, /* getDescriptor */
0x2300, 0, data, 0x12, 0);
Signed-off-by: Roger Quadros <roger.quadros@nokia.com> Cc: stable <stable@kernel.org> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Robert Lukassen <robert.lukassen@tomtom.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 10 Sep 2010 20:37:05 +0000 (16:37 -0400)]
OHCI: work around for nVidia shutdown problem
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
USB: Change acm_iad_descriptor bFunctionProtocol to USB_CDC_ACM_PROTO_AT_V25TER
The protocol code is set 00 in IAD and it's set to 01 in ACM control
interface descriptor in f_acm.c file. Due to this, windows is unable to
install the modem(ACM) driver based on class-subclass-protocol matching.
This patch corrects the protocol code in ACM IAD to the same as in
acm_control_interface_desc protocol code.
USB OTG: Add common data structure for Intel MID Platform (Langwell/Penwell)
This patch adds one new header file for the common data structure used in
Intel Penwell/Langwell MID Platform OTG Transceiver drivers. After switched
to the common data structure, Langwell/Penwell OTG Transceiver driver will
provide an unified interface to host/client driver.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Hao Wu <hao.wu@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Michael Prokop [Mon, 6 Sep 2010 07:53:48 +0000 (09:53 +0200)]
USB: Kconfig: fix typos in USB_FUNCTIONFS* description
It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: Michael Prokop <mika@grml.org> Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 3 Sep 2010 15:15:41 +0000 (11:15 -0400)]
USB: g_file_storage: don't generate automatic serial string
This patch (as1413) changes g_file_storage to avoid generating a bogus
automatic serial-number string descriptor. If the user doesn't provide
a valid serial number via a module parameter then a warning is logged
and the gadget won't have any serial string descriptor at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> CC: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Mon, 30 Aug 2010 21:50:20 +0000 (22:50 +0100)]
USB: output an error message when the pipe type doesn't match the endpoint type
Commit f661c6f8c67bd55e93348f160d590ff9edf08904 adds a check of the pipe type if
CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario
occurs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
init.h: add some more documentation to __ref* tags
The __ref* tags may have been confusing for new kernel
developers (I was confused by them for sure) so adding a few
more sentences to comment to clear things up for people who
see those for the first time.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Uwe Kleine-König [Thu, 12 Aug 2010 15:43:53 +0000 (17:43 +0200)]
usb gadget: don't save bind callback in struct usb_gadget_driver
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
USB: gadget: g_multi: moved strings handling code to composite
This patch removes some of the string registration from the
Multifunction Composite Gadget as composite layer can handle
the iManufacturer and iProduct for us.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: gadget: mass_storage: moved strings handling code to composite
This patch removes string registration from the Mass Storage
Gadget. With recent changes to the composite framework, all
that we need is handled by the composite layer. This means
composite registers a string ID for manufacturer and product.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iManufatcurer, iProduct and iSerialNumber composite module
parameters were only used when the gadget driver registers
strings for manufacturer, product and serial number. If the
gadget never bothered to set corresponding fields in USB device
descriptors those module parameters are ignored.
This commit makes the parameters work even if the strings ID
have not been assigned. It also changes the way IDs are
overridden -- what IDs are overridden is now saved in
usb_composite_dev structure -- which makes it unnecessary to
modify the string tables the way previous code did.
The commit also adds a iProduct and iManufatcurer fields to the
usb_composite_device structure. If they are set, appropriate
strings are reserved and added to device descriptor. This makes
it unnecessary for gadget drivers to maintain code for setting
those. If iProduct is not set it defaults to
usb_composite_device::name; if iManufatcurer is not set
a default "<system> <release> with <gadget-name>" is used.
The last thing is that if needs_serial field of
usb_composite_device is set and user failed to provided
iSerialNumber parameter a warning is issued.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes some of the string registration from the
FunctionFS Gadget as composite layer can handle the
iManufacturer and iProduct for us.
It also removes some of the module parameters which were
redundant as well as changes the name of others to better much
the module parameter of the composite layer.
Other then that, it also fixes formatting of multiline comments
to match the coding style.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: gadget: mass_storage: optional SCSI WRITE FUA bit
The nofua parameter (optionally ignore SCSI WRITE FUA) was added
to the File Storage Gadget some time ago. This patch adds the
same functionality to the Mass Storage Function.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: gadget: storage: remove nofua file when unbinding
The dev_attr_nofua file was created during fsg_bind() but
was never removed. Made it a bit more symmetrical and added
code to remove the file in fsg_unbind().
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Acked-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Carpenter [Thu, 12 Aug 2010 07:40:30 +0000 (09:40 +0200)]
USB: gadget: dbgp: cleanup: remove unneeded check
len is always greater than or equal to zero here. First of all, it's
type is unsigned and also we only assign it numbers which are greater
than or equal to zero.
Removing the check lets us pull everything in an indent level.
Hao Wu [Thu, 5 Aug 2010 13:17:28 +0000 (14:17 +0100)]
usb: Add Intel Langwell USB OTG Transceiver Driver
This adds support for the USB transceiver driver in the Langwell chipset used
on the Intel MID platforms. It folds up the original patch set which includes
basic support for the device, PHY low power mode (Please notice that there is
a limitation, after we drive VBus down, 2ms delay is required from SCU FW to
sync up OTGSC register with USBCFG register), software timers (the hardware
timers do not work in low power mode), HNP, SRP.
Signed-off-by: Hao Wu <hao.wu@intel.com> Signed-off-by: Alek Du <alek.du@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Wed, 20 Oct 2010 20:18:21 +0000 (13:18 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
MAINTAINERS: Change list for ioc_serial to linux-serial.
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
MIPS: jz4740: Fix Kbuild Platform file.
MIPS: Repair Kbuild make clean breakage.
Amit Shah [Wed, 20 Oct 2010 03:15:43 +0000 (13:45 +1030)]
virtio: console: Don't block entire guest if host doesn't read data
If the host is slow in reading data or doesn't read data at all,
blocking write calls not only blocked the program that called write()
but the entire guest itself.
To overcome this, let's not block till the host signals it has given
back the virtio ring element we passed it. Instead, send the buffer to
the host and return to userspace. This operation then becomes similar
to how non-blocking writes work, so let's use the existing code for this
path as well.
This code change also ensures blocking write calls do get blocked if
there's not enough room in the virtio ring as well as they don't return
-EAGAIN to userspace.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Acked-by: Hans de Goede <hdegoede@redhat.com> CC: stable@kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Tue, 19 Oct 2010 17:32:41 +0000 (18:32 +0100)]
MAINTAINERS: Change list for ioc_serial to linux-serial.
IOC3 is also being used on SGI MIPS systems but this particular driver is
only being used on IA64 systems so linux-mips made no sense as a list. Pat
also thinks linux-serial@vger.kernel.org is the better list.
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com> Cc: kernel-janitors@vger.kernel.org Cc: linux-ia64@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 19 Oct 2010 00:51:26 +0000 (17:51 -0700)]
MIPS: Repair Kbuild make clean breakage.
When running make clean, Kbuild doesn't process the .config file, so nothing
generates a platform-y variable. We can get it to descend into the platform
directories by setting $(obj-).
The dec Platform file was unconditionally setting platform-, obliterating
its previous contents and preventing some directories from being cleaned.
This is change to an append operation '+=' to allow cavium-octeon to be
cleaned.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Cc: Sam Ravnborg <sam@ravnborg.org>
Patchwork: https://patchwork.linux-mips.org/patch/1718/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avi Kivity [Tue, 19 Oct 2010 14:46:55 +0000 (16:46 +0200)]
KVM: Fix fs/gs reload oops with invalid ldt
kvm reloads the host's fs and gs blindly, however the underlying segment
descriptors may be invalid due to the user modifying the ldt after loading
them.
Fix by using the safe accessors (loadsegment() and load_gs_index()) instead
of home grown unsafe versions.
This is CVE-2010-3698.
KVM-Stable-Tag. Signed-off-by: Avi Kivity <avi@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Mon, 18 Oct 2010 20:10:36 +0000 (13:10 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
Sascha Hauer [Mon, 18 Oct 2010 08:16:26 +0000 (10:16 +0200)]
mxc_nand: do not depend on disabling the irq in the interrupt handler
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: John Ogness <john.ogness@linutronix.de> Tested-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / mirror_ubuntu-kernels.git / log