Bruce Allan [Fri, 7 Aug 2009 07:41:56 +0000 (07:41 +0000)]
e1000e: fix potential NVM corruption on ICH9 with 8K bank size
The bank offset was being incorrectly calculated on ICH9 parts with a bank
size of 8K (instead of the more common 4K bank) which would cause any NVM
writes to be done on the wrong address after switching from bank 1 to bank
0. Additionally, assume we are meant to use bank 0 if a valid bank is not
detected, and remove the unnecessary acquisition of the SW/FW/HW semaphore
when writing to the shadow ram version of the NVM image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 7 Aug 2009 07:41:37 +0000 (07:41 +0000)]
e1000e: fix acquisition of SW/FW/HW semaphore for ICHx parts
For ICHx parts, write the EXTCNF_CTRL.SWFLAG bit once when trying to
acquire the SW/FW/HW semaphore instead of multiple times to prevent the
hardware from having problems (especially for systems with manageability
enabled), and extend the timeout for the hardware to set the SWFLAG bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Thu, 6 Aug 2009 13:05:44 +0000 (13:05 +0000)]
ixgbe: Disable packet split only on FCoE queues in 82599
For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).
Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Thu, 6 Aug 2009 13:05:23 +0000 (13:05 +0000)]
ixgbe: Pass rx_ring directly in ixgbe_configure_srrctl()
Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.
Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 6 Aug 2009 14:22:44 +0000 (14:22 +0000)]
tun: Extend RTNL lock coverage over whole ioctl
As it is, parts of the ioctl runs under the RTNL and parts of
it do not. The unlocked section is still protected by the BKL,
but there can be subtle races. For example, Eric Biederman and
Paul Moore observed that if two threads tried to create two tun
devices on the same file descriptor, then unexpected results
may occur.
As there isn't anything in the ioctl that is expected to sleep
indefinitely, we can prevent this from occurring by extending
the RTNL lock coverage.
This also allows to get rid of the BKL.
Finally, I changed tun_get_iff to take a tun device in order to
avoid calling tun_put which would dead-lock as it also tries to
take the RTNL lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Ungerer [Thu, 6 Aug 2009 17:58:18 +0000 (17:58 +0000)]
fec: fix FEC driver packet transmission breakage
Commit f0b3fbeae11a526c3d308b691684589ee37c359b ("FEC Buffer rework")
breaks transmission of packets where the skb data buffer is not memory
aligned according to FEC_ALIGNMENT. It incorrectly passes to
dma_sync_single() the buffer address directly from the skb, instead of
the address calculated for use (which may be the skb address or one of
the bounce buffers).
It seems there is no use converting the cpu address of the buffer to
a physical either, since dma_map_single() expects the cpu address and
will return the dma address to use in the descriptor. So remove the use
of __pa() on the buffer address as well.
This patch is against 2.6.30-rc5. This breakage is a regression over
2.6.30, which does not have this problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 6 Aug 2009 20:27:04 +0000 (20:27 +0000)]
can: Fix raw_getname() leak
raw_getname() can leak 10 bytes of kernel memory to user
(two bytes hole between can_family and can_ifindex,
8 bytes at the end of sockaddr_can structure)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jussi Mäki [Thu, 6 Aug 2009 21:38:14 +0000 (21:38 +0000)]
Fix xfrm hash collisions by changing __xfrm4_daddr_saddr_hash to hash addresses with addition
This patch fixes hash collisions in cases where number
of entries have incrementing IP source and destination addresses
from single respective subnets (i.e. 192.168.0.1-172.16.0.1,
192.168.0.2-172.16.0.2, and so on.).
Signed-off-by: Jussi Maki <joamaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Thu, 6 Aug 2009 13:06:56 +0000 (13:06 +0000)]
atlx: strncpy does not null terminate string
strlcpy() will always null terminate the string.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <csnook@redhat.com> Cc: Jie Yang <jie.yang@atheros.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Thu, 6 Aug 2009 13:06:03 +0000 (13:06 +0000)]
irda: fix read buffer overflow
io[i] is read before the bounds check on i, order should be reversed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Snook [Thu, 6 Aug 2009 12:19:31 +0000 (12:19 +0000)]
MAINTAINERS: update atlx contact info
Update MAINTAINERS to reflect my current (non-)affiliation. Anyone
hiring?
Signed-off-by: Chris Snook <chris.snook@gmail.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 9 Aug 2009 21:58:21 +0000 (14:58 -0700)]
Merge branch 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid redelivery of edge interrupt before next edge
KVM: MMU: limit rmap chain length
KVM: ia64: fix build failures due to ia64/unsigned long mismatches
KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to avoid build error on powerpc
KVM: fix ack not being delivered when msi present
KVM: s390: fix wait_queue handling
KVM: VMX: Fix locking imbalance on emulation failure
KVM: VMX: Fix locking order in handle_invalid_guest_state
KVM: MMU: handle n_free_mmu_pages > n_alloc_mmu_pages in kvm_mmu_change_mmu_pages
KVM: SVM: force new asid on vcpu migration
KVM: x86: verify MTRR/PAT validity
KVM: PIT: fix kpit_elapsed division by zero
KVM: Fix KVM_GET_MSR_INDEX_LIST
Linus Torvalds [Sun, 9 Aug 2009 21:57:41 +0000 (14:57 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
posix_cpu_timers_exit_group(): Do not use thread_group_cputimer()
Linus Torvalds [Sun, 9 Aug 2009 21:57:26 +0000 (14:57 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Fix/complete ftrace event records sampling
perf_counter, ftrace: Fix perf_counter integration
tracing/filters: Always free pred on filter_add_subsystem_pred() failure
tracing/filters: Don't use pred on alloc failure
ring-buffer: Fix memleak in ring_buffer_free()
tracing: Fix recordmcount.pl to handle sections with only weak functions
ring-buffer: Fix advance of reader in rb_buffer_peek()
tracing: do not use functions starting with .L in recordmcount.pl
ring-buffer: do not disable ring buffer on oops_in_progress
ring-buffer: fix check of try_to_discard result
Linus Torvalds [Sun, 9 Aug 2009 21:57:09 +0000 (14:57 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix buffer overflow in efi_init()
x86: Add quirk to make Apple MacBookPro5,1 use reboot=pci
x86: Fix MSI-X initialization by using online_mask for x2apic target_cpus
x86: Fix VMI && stack protector
Linus Torvalds [Sun, 9 Aug 2009 21:56:51 +0000 (14:56 -0700)]
Merge branch 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: Fix typos in documentation
lockdep: Fix file mode of lock_stat
rtmutex: Avoid deadlock in rt_mutex_start_proxy_lock()
perf_counter: Fix/complete ftrace event records sampling
This patch implements the kernel side support for ftrace event
record sampling.
A new counter sampling attribute is added:
PERF_SAMPLE_TP_RECORD
which requests ftrace events record sampling. In this case
if a PERF_TYPE_TRACEPOINT counter is active and a tracepoint
fires, we emit the tracepoint binary record to the
perfcounter event buffer, as a sample.
Result, after setting PERF_SAMPLE_TP_RECORD attribute from perf
record:
perf record -f -F 1 -a -e workqueue:workqueue_execution
perf report -D
- Userspace support ('perf trace'), 'flight data recorder' mode
for perf trace, etc.
- The unconditional copy from the profiling callback brings
some costs however if someone wants no such sampling to
occur, and needs to be fixed in the future. For that we need
to have an instant access to the perf counter attribute.
This is a matter of a flag to add in the struct ftrace_event.
- Take care of the events recursivity! Don't ever try to record
a lock event for example, it seems some locking is used in
the profiling fast path and lead to a tracing recursivity.
That will be fixed using raw spinlock or recursivity
protection.
- [...]
- Profit! :-)
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Tom Zanussi <tzanussi@gmail.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Mike Galbraith <efault@gmx.de> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Gabriel Munteanu <eduard.munteanu@linux360.ro> Cc: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Which, when specified make the swcounter increment with @foo instead
of the usual 1, and report @bar for PERF_SAMPLE_ADDR (data address
associated with the event) when this triggers a counter overflow.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jason Baron <jbaron@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
KVM: Avoid redelivery of edge interrupt before next edge
The check for an edge is broken in current ioapic code. ioapic->irr is
cleared on each edge interrupt by ioapic_service() and this makes
old_irr != ioapic->irr condition in kvm_ioapic_set_irq() to be always
true. The patch fixes the code to properly recognise edge.
Some HW emulation calls set_irq() without level change. If each such
call is propagated to an OS it may confuse a device driver. This is the
case with keyboard device emulation and Windows XP x64 installer on SMP VM.
Each keystroke produce two interrupts (down/up) one interrupt is
submitted to CPU0 and another to CPU1. This confuses Windows somehow
and it ignores keystrokes.
Signed-off-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Paul Rolland [Sun, 9 Aug 2009 02:24:01 +0000 (12:24 +1000)]
drm: silence pointless vblank warning.
Some applications/hardware combinations are triggering the message "failed to
acquire vblank counter" to be issued up to 20 times a second, which makes it
both useless and dangerous, as this may hide other important messages.
This changes makes it only appear when people are debugging.
Signed-off-by: Paul Rolland <rol@as2917.net> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Lost-twice-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Keith Packard [Mon, 20 Jul 2009 21:49:17 +0000 (14:49 -0700)]
drm: When adding probed modes, preserve duplicate mode types
The code which takes probed modes and adds them to a connector eliminates
duplicate modes by comparing them using drm_mode_equal. That function
doesn't consider the type bits, which means that any modes which differ only
in the type field will be lost.
One of the bits in the mode->type field is the DRM_MODE_TYPE_PREFERRED bit.
If the mode with that bit is lost, then higher level code will not know
which mode to select, causing a random mode to be used instead.
This patch simply merges the two mode type bits together; that seems
reasonable to me, but perhaps only a subset of the bits should be used? None
of these can be user defined as they all come from looking at just the
hardware.
Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
posix_cpu_timers_exit_group(): Do not use thread_group_cputimer()
When the process exits we don't have to run new cputimer nor
use running one (as it not accounts when tsk->exit_state != 0)
to get process CPU times. As there is only one thread we can
just use CPU times fields from task and signal structs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Roland McGrath <roland@redhat.com> Cc: Vitaly Mayatskikh <vmayatsk@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tom Zanussi [Sat, 8 Aug 2009 15:49:53 +0000 (10:49 -0500)]
tracing/filters: Always free pred on filter_add_subsystem_pred() failure
If filter_add_subsystem_pred() fails due to ENOSPC or ENOMEM,
the pred doesn't get freed, while as a side effect it does for
other errors. Make it so the caller always frees the pred for
any error.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1249746593.6453.32.camel@tropicana> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tom Zanussi [Sat, 8 Aug 2009 15:49:09 +0000 (10:49 -0500)]
tracing/filters: Don't use pred on alloc failure
Dan Carpenter sent me a fix to prevent pred from being used if
it couldn't be allocated. I noticed the same problem also
existed for the create_pred() case and added a fix for that.
Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Tom Zanussi <tzanussi@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <1249746549.6453.29.camel@tropicana> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Tue, 4 Aug 2009 15:59:59 +0000 (08:59 -0700)]
x86: Fix MSI-X initialization by using online_mask for x2apic target_cpus
found a system where x2apic reports an MSI-X irq initialization
failure:
[ 302.859446] igbvf 0000:81:10.4: enabling device (0000 -> 0002)
[ 302.874369] igbvf 0000:81:10.4: using 64bit DMA mask
[ 302.879023] igbvf 0000:81:10.4: using 64bit consistent DMA mask
[ 302.894386] igbvf 0000:81:10.4: enabling bus mastering
[ 302.898171] igbvf 0000:81:10.4: setting latency timer to 64
[ 302.914050] reserve_memtype added 0xefb08000-0xefb0c000, track uncached-minus, req uncached-minus, ret uncached-minus
[ 302.933839] reserve_memtype added 0xefb28000-0xefb29000, track uncached-minus, req uncached-minus, ret uncached-minus
[ 302.940367] alloc irq_desc for 265 on node 4
[ 302.956874] alloc kstat_irqs on node 4
[ 302.959452] alloc irq_2_iommu on node 0
[ 302.974328] igbvf 0000:81:10.4: irq 265 for MSI/MSI-X
[ 302.977778] alloc irq_desc for 266 on node 4
[ 302.980347] alloc kstat_irqs on node 4
[ 302.995312] free_memtype request 0xefb28000-0xefb29000
[ 302.998816] igbvf 0000:81:10.4: Failed to initialize MSI-X interrupts.
... it turns out that when trying to enable MSI-X,
__assign_irq_vector(new, cfg_new, apic->target_cpus()) can not
get vector because for x2apic target-cpus returns cpumask_of(0)
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix oops on disconnect in cdc-acm
USB: storage: include Prolific Technology USB drive in unusual_devs list
USB: ftdi_sio: add product_id for Marvell OpenRD Base, Client
USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial converter cable
USB: EHCI: fix counting of transaction error retries
USB: EHCI: fix two new bugs related to Clear-TT-Buffer
USB: usbfs: fix -ENOENT error code to be -ENODEV
USB: musb: fix the nop registration for OMAP3EVM
USB: devio: Properly do access_ok() checks
USB: pl2303: New vendor and product id
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: rspiusb: Fix buffer overflow
staging: add dependencies on PCI for drivers that require it
Staging: rtl8192su: fix build error
Staging: rt2870: Revert d44ca7 Removal of kernel_thread() API
Staging: rt2870: Add USB ID for Linksys, Planex Communications, Belkin
Linus Torvalds [Sat, 8 Aug 2009 02:03:59 +0000 (19:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (22 commits)
drm/i915: Fix read outside array bounds in restoring the SWF10 range.
drm/i915: Use our own workqueue to avoid wedging the system along with the GPU.
drm/i915: Add support for dual-channel LVDS on 8xx.
drm/i915: Return disconnected for SDVO DVI when there's no digital EDID.
drm/i915: Choose real sdvo output according to result from detection
drm/i915: Set preferred mode for integrated TV according to TV format
drm/i915: fix 845G FIFO size & burst length
drm/i915: fix VGA detect on IGDNG
drm/i915: Add eDP support on IGDNG mobile chip
drm/i915: enable DisplayPort support on IGDNG
drm/i915: Fix channel ending action for DP aux transaction
drm/i915: fix issue in display pipe setup on IGDNG
drm/i915: disable VGA plane reliably
drm/I915: Fix offset to DVO timings in LVDS data
drm/i915: hdmi detection according by reading edid
drm/i915: correct self-refresh calculation in "everything off" case
drm/i915: handle FIFO oversubsription correctly
drm/i915: FIFO watermark calculation fixes
drm/i915: ignore lvds on AOpen Mini PC MP-915
drm/i915: Allow frame buffers up to 4096x4096 on 915/945 class hardware
...
This fixes a build error when selecting the rtl8192su driver as a
module. This has been reported by me, and the opensuse kernel developer
team, and I finally tracked it down.
Oliver Neukum [Tue, 4 Aug 2009 21:52:09 +0000 (23:52 +0200)]
USB: fix oops on disconnect in cdc-acm
This patch fixes an oops caused when during an unplug a device's table
of endpoints is zeroed before the driver is notified. A pointer to
the endpoint must be cached.
Marko Hänninen [Fri, 31 Jul 2009 19:32:39 +0000 (22:32 +0300)]
USB: ftdi_sio: add vendor and product id for Bayer glucose meter serial converter cable
Attached patch adds USB vendor and product IDs for Bayer's USB to serial
converter cable used by Bayer blood glucose meters. It seems to be a
FT232RL based device and works without any problem with ftdi_sio driver
when this patch is applied. See: http://winglucofacts.com/cables/
Alan Stern [Fri, 31 Jul 2009 14:41:40 +0000 (10:41 -0400)]
USB: EHCI: fix counting of transaction error retries
This patch (as1274) simplifies the counting of transaction-error
retries. Now we will count up from 0 to QH_XACTERR_MAX instead of
down from QH_XACTERR_MAX to 0.
The patch also fixes a small bug: qh->xacterr was not getting
initialized for interrupt endpoints.
Alan Stern [Fri, 31 Jul 2009 14:40:22 +0000 (10:40 -0400)]
USB: EHCI: fix two new bugs related to Clear-TT-Buffer
This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.
It is now possible for an idle QH to have some URBs on its
queue -- this will happen if a Clear-TT-Buffer is pending for
the QH's endpoint. Consequently we should not issue a warning
when someone tries to unlink an URB from an idle QH; instead
we should process the request immediately.
The refcounts for QHs could get messed up, because
submit_async() would increment the refcount when calling
qh_link_async() and qh_link_async() would then refuse to link
the QH into the schedule if a Clear-TT-Buffer was pending.
Instead we should increment the refcount only when the QH
actually is added to the schedule. The current code tries to
be clever by leaving the refcount alone if an unlink is
immediately followed by a relink; the patch changes this to an
unconditional decrement and increment (although they occur in
the opposite order).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by: Manuel Lauss <manuel.lauss@gmail.com> Tested-by: Matthijs Kooijman <matthijs@stdin.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 30 Jul 2009 19:28:14 +0000 (15:28 -0400)]
USB: usbfs: fix -ENOENT error code to be -ENODEV
This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device. The
appropriate error code is -ENODEV, not -ENOENT.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Kay Sievers <kay.sievers@vrfy.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Buesch [Wed, 29 Jul 2009 09:39:03 +0000 (11:39 +0200)]
USB: devio: Properly do access_ok() checks
access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).
This changes the __get_user() users to first check access_ok() on the
data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: stable <stable@kernel.org> Cc: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am submitting a patch for the pl2303 driver. This patch adds support
for the "Sony QN-3USB" cable (vendor=0x054c, product=0x0437). This USB
cable is a so-called data cable used to connect a Sony mobile phone to a
computer. Supported models are Sony CMD-J5, J6, J7, J16, J26, J70 and
Z7.
I have used this patch with my Sony CMD-J70 for several days and I
haven't encountered any kernel/hardware issue.
Yan Zheng [Fri, 7 Aug 2009 17:51:33 +0000 (13:51 -0400)]
Btrfs: fix balancing oops when invalidate_inode_pages2 returns EBUSY
invalidate_inode_pages2_range may return -EBUSY occasionally
which results Oops. This patch fixes the issue by moving
invalidate_inode_pages2_range into a loop and keeping calling
it until the return value is not -EBUSY.
The EBUSY return is temporary, and can happen when the btrfs release page
function is unable to release a page because the EXTENT_LOCK
bit is set.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Fri, 7 Aug 2009 17:43:07 +0000 (10:43 -0700)]
Merge branch 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Fix double list iteration in per task precise stats
perf: Auto-detect libelf
perf symbol: Fix symbol parsing in certain cases: use the build-id as a symlink
perf_counter/powerpc: Check oprofile_cpu_type for NULL before using it
ftrace: Fix perf-tracepoint OOPS
perf report: Add missing command line options to man page
perf: Auto-detect libbfd
perf report: Make --sort comm,dso,symbol the default
Linus Torvalds [Fri, 7 Aug 2009 17:42:31 +0000 (10:42 -0700)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
jffs2: Fix return value from jffs2_do_readpage_nolock()
mtd: mtdblock: introduce mtdblks_lock
mtd: remove 'SBC8240 Wind River' Device Driver Code
mtd: OneNAND: OMAP2/3: free GPMC CS on module removal
mtd: OneNAND: fix incorrect bufferram offset
mtd: blkdevs: do not forget to get MTD devices
mtd: fix the conversion from dev to mtd_info
mtd: let include/linux/mtd/partitions.h stand on its own
Linus Torvalds [Fri, 7 Aug 2009 17:41:36 +0000 (10:41 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: setup MC/VRAM the same way for suspend/resume
drm/radeon/kms: Fix caching mode selection for GTT object
Albin Tonnerre [Thu, 6 Aug 2009 22:09:32 +0000 (15:09 -0700)]
lib/decompress_*: only include <linux/slab.h> if STATIC is not defined
These includes were added by 079effb6933f34b9b1b67b08bd4fd7fb672d16ef
("kmemtrace, kbuild: fix slab.h dependency problem in
lib/decompress_inflate.c") to fix the build when using kmemtrace. However
this is not necessary when used to create a compressed kernel, and
actually creates issues (brings a lot of things unavailable in the
decompression environment), so don't include it if STATIC is defined.
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> Cc: Phillip Lougher <phillip@lougher.demon.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Thu, 6 Aug 2009 22:09:31 +0000 (15:09 -0700)]
bzip2/lzma: remove nasty uncompressed size hack in pre-boot environment
decompress_bunzip2 and decompress_unlzma have a nasty hack that subtracts
4 from the input length if being called in the pre-boot environment.
This is a nasty hack because it relies on the fact that flush = NULL only
when called from the pre-boot environment (i.e.
arch/x86/boot/compressed/misc.c). initramfs.c/do_mounts_rd.c pass in a
flush buffer (flush != NULL).
This hack prevents the decompressors from being used with flush = NULL by
other callers unless knowledge of the hack is propagated to them.
This patch removes the hack by making decompress (called only from the
pre-boot environment) a wrapper function that subtracts 4 from the input
length before calling the decompressor.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Phillip Lougher [Thu, 6 Aug 2009 22:09:30 +0000 (15:09 -0700)]
bzip2/lzma/gzip: fix comments describing decompressor API
Fix and improve comments in decompress/generic.h that describe the
decompressor API. Also remove an unused definition, and rename INBUF_LEN
in lib/decompress_inflate.c to conform to bzip2/lzma naming.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Dumazet [Thu, 6 Aug 2009 22:09:28 +0000 (15:09 -0700)]
execve: must clear current->clear_child_tid
While looking at Jens Rosenboom bug report
(http://lkml.org/lkml/2009/7/27/35) about strange sys_futex call done from
a dying "ps" program, we found following problem.
clone() syscall has special support for TID of created threads. This
support includes two features.
One (CLONE_CHILD_SETTID) is to set an integer into user memory with the
TID value.
One (CLONE_CHILD_CLEARTID) is to clear this same integer once the created
thread dies.
The integer location is a user provided pointer, provided at clone()
time.
kernel keeps this pointer value into current->clear_child_tid.
At execve() time, we should make sure kernel doesnt keep this user
provided pointer, as full user memory is replaced by a new one.
As glibc fork() actually uses clone() syscall with CLONE_CHILD_SETTID and
CLONE_CHILD_CLEARTID set, chances are high that we might corrupt user
memory in forked processes.
Following sequence could happen:
1) bash (or any program) starts a new process, by a fork() call that
glibc maps to a clone( ... CLONE_CHILD_SETTID | CLONE_CHILD_CLEARTID
...) syscall
2) When new process starts, its current->clear_child_tid is set to a
location that has a meaning only in bash (or initial program) context
(&THREAD_SELF->tid)
3) This new process does the execve() syscall to start a new program.
current->clear_child_tid is left unchanged (a non NULL value)
4) If this new program creates some threads, and initial thread exits,
kernel will attempt to clear the integer pointed by
current->clear_child_tid from mm_release() :
/*
* We don't check the error code - if userspace has
* not set up a proper pointer then tough luck.
*/
<< here >> put_user(0, tidptr);
sys_futex(tidptr, FUTEX_WAKE, 1, NULL, NULL, 0);
}
5) OR : if new program is not multi-threaded, but spied by /proc/pid
users (ps command for example), mm_users > 1, and the exiting program
could corrupt 4 bytes in a persistent memory area (shm or memory mapped
file)
If current->clear_child_tid points to a writeable portion of memory of the
new program, kernel happily and silently corrupts 4 bytes of memory, with
unexpected effects.
Fix is straightforward and should not break any sane program.
x = sdhci_alloc_host(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Matt Fleming <matt@console-pimps.org> Cc: Ian Molton <ian@mnementh.co.uk> Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com> Cc: Philip Langdale <philipl@overt.org> Cc: Pierre Ossman <pierre@ossman.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent framebuffer locking patches first made affected systems unbootable,
then the dead-lock has been fixed but as of 2.6.31-rc4 the framebuffer on
mx3 machines doesn't work. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Thu, 6 Aug 2009 22:07:39 +0000 (15:07 -0700)]
vfs: mnt_want_write_file(): fix special file handling
I suspect that mnt_want_write_file() may have wrong assumption. I think
mnt_want_write_file() is assuming it increments ->mnt_writers if
(file->f_mode & FMODE_WRITE). But, if it's special_file(), it is false?
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Acked-by: Dave Hansen <dave@linux.vnet.ibm.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Sandeen [Thu, 6 Aug 2009 22:07:37 +0000 (15:07 -0700)]
compat_ioctl: hook up compat handler for FIEMAP ioctl
The FIEMAP_IOC_FIEMAP mapping ioctl was missing a 32-bit compat handler,
which means that 32-bit suerspace on 64-bit kernels cannot use this ioctl
command.
The structure is nicely aligned, padded, and sized, so it is just this
simple.
Tested w/ 32-bit ioctl tester (from Josef) on a 64-bit kernel on ext4.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Cc: <linux-ext4@vger.kernel.org> Cc: Mark Lord <lkml@rtr.ca> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Josef Bacik <josef@redhat.com> Cc: Jan Kara <jack@suse.cz> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The common way for the VC drivers is to set the screen dimension
parameters manually in the init case and only call vc_resize() for
!init - which allocates a screen buffer according to the new
dimensions.
fbcon instead would do vc_resize() unconditionally and afterwards set
the dimensions manually (again) for !init - i.e. completely upside
down. The vc_resize() allocated buffer would then get lost by
vc_allocate() allocating a fresh one.
Use vc_resize() only for actual resizing to close the leak.
Set the dimensions manually only in initialization mode to remove the
redundant setting in resize mode.
Reported-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Tested-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Tested-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a bug caused by changing pointers (viafb_mode, viafb_mode1)
assigned by module_param. It reduces driver complexity by not needlessly
changing these vars as they are only read once and removing now
superfluous code.
On unpatched kernels loading viafb with viafb_mode or viafb_mode1 option
used and afterwards unloading it results in:
This is caused by the current code changing the pointers assigned by
module_param. During unload it tries to free the memory the pointers
point at which is now part of an internal structure.
The patch simply avoids changing the pointers. This is okay as they are
read only once during the initialization process.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: make set_mempolicy(MPOL_INTERLEAV) N_HIGH_MEMORY aware
At first, init_task's mems_allowed is initialized as this.
init_task->mems_allowed == node_state[N_POSSIBLE]
And cpuset's top_cpuset mask is initialized as this
top_cpuset->mems_allowed = node_state[N_HIGH_MEMORY]
Before 2.6.29:
policy's mems_allowed is initialized as this.
1. update tasks->mems_allowed by its cpuset->mems_allowed.
2. policy->mems_allowed = nodes_and(tasks->mems_allowed, user's mask)
Updating task's mems_allowed in reference to top_cpuset's one.
cpuset's mems_allowed is aware of N_HIGH_MEMORY, always.
In 2.6.30: After commit 58568d2a8215cb6f55caf2332017d7bdff954e1c
("cpuset,mm: update tasks' mems_allowed in time"), policy's mems_allowed
is initialized as this.
Then, policy's mems_allowd can includes a possible node, which has no pgdat.
MPOL's INTERLEAVE just scans nodemask of task->mems_allowd and access this
directly.
NODE_DATA(nid)->zonelist even if NODE_DATA(nid)==NULL
Then, what's we need is making policy->mems_allowed be aware of
N_HIGH_MEMORY. This patch does that. But to do so, extra nodemask will
be on statck. Because I know cpumask has a new interface of
CPUMASK_ALLOC(), I added it to node.
This patch stands on old behavior. But I feel this fix itself is just a
Band-Aid. But to do fundametal fix, we have to take care of memory
hotplug and it takes time. (task->mems_allowd should be N_HIGH_MEMORY, I
think.)
mpol_set_nodemask() should be aware of N_HIGH_MEMORY and policy's nodemask
should be includes only online nodes.
In old behavior, this is guaranteed by frequent reference to cpuset's
code. Now, most of them are removed and mempolicy has to check it by
itself.
To do check, a few nodemask_t will be used for calculating nodemask. But,
size of nodemask_t can be big and it's not good to allocate them on stack.
Now, cpumask_t has CPUMASK_ALLOC/FREE an easy code for get scratch area.
NODEMASK_ALLOC/FREE shoudl be there.
[akpm@linux-foundation.org: cleanups & tweaks] Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Miao Xie <miaox@cn.fujitsu.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Paul Menage <menage@google.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: David Rientjes <rientjes@google.com> Cc: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefani Seibold [Thu, 6 Aug 2009 22:07:30 +0000 (15:07 -0700)]
fbcon: fix rotate upside down crash
Fix the rotate_ud() function not to crash in case of a font which has not
a width of multiple by 8: The inner loop of the font pixel copy should not
access a bit outside the font memory area. Subtract the shift offset from
the font width will prevent this.
Signed-off-by: Stefani Seibold <stefani@seibold.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xfs: fix freeing of inodes not yet added to the inode cache
When freeing an inode that lost race getting added to the inode cache we
must not call into ->destroy_inode, because that would delete the inode
that won the race from the inode cache radix tree.
This patch uses splits a new xfs_inode_free helper out of xfs_ireclaim
and uses that plus __destroy_inode to make sure we really only free
the memory allocted for the inode that lost the race, and not mess with
the inode cache state.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Eric Sandeen <sandeen@sandeen.net> Reported-by: Alex Samad <alex@samad.com.au> Reported-by: Andrew Randrianasulu <randrik@mail.ru> Reported-by: Stephane <sharnois@max-t.com> Reported-by: Tommy <tommy@news-service.com> Reported-by: Miah Gregory <mace@darksilence.net> Reported-by: Gabriel Barazer <gabriel@oxeva.fr> Reported-by: Leandro Lucarella <llucax@gmail.com> Reported-by: Daniel Burr <dburr@fami.com.au> Reported-by: Nickolay <newmail@spaces.ru> Reported-by: Michael Guntsche <mike@it-loops.com> Reported-by: Dan Carley <dan.carley+linuxkern-bugs@gmail.com> Reported-by: Michael Ole Olsen <gnu@gmx.net> Reported-by: Michael Weissenbacher <mw@dermichi.com> Reported-by: Martin Spott <Martin.Spott@mgras.net> Reported-by: Christian Kujau <lists@nerdbynature.de> Tested-by: Michael Guntsche <mike@it-loops.com> Tested-by: Dan Carley <dan.carley+linuxkern-bugs@gmail.com> Tested-by: Christian Kujau <lists@nerdbynature.de>
When we want to tear down an inode that lost the add to the cache race
in XFS we must not call into ->destroy_inode because that would delete
the inode that won the race from the inode cache radix tree.
This patch provides the __destroy_inode helper needed to fix this,
the actual fix will be in th next patch. As XFS was the only reason
destroy_inode was exported we shift the export to the new __destroy_inode.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Currently inode_init_always calls into ->destroy_inode if the additional
initialization fails. That's not only counter-intuitive because
inode_init_always did not allocate the inode structure, but in case of
XFS it's actively harmful as ->destroy_inode might delete the inode from
a radix-tree that has never been added. This in turn might end up
deleting the inode for the same inum that has been instanciated by
another process and cause lots of cause subtile problems.
Also in the case of re-initializing a reclaimable inode in XFS it would
free an inode we still want to keep alive.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Bob Dunlop [Thu, 6 Aug 2009 16:01:03 +0000 (12:01 -0400)]
libertas: correct packing of rxpd structure
Older Gcc compilers (3.4.5 tested) need additional hints in order to get
the packing of the rxpd structure (which contains a 16 bit union)
correct on the ARM processor.
struct txpd does not need these hints since it contains a 32 bit union
that packs naturally.
Signed-off-by: R.J.Dunlop <rdunlop@guralp.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to unregister our ieee80211_hw before resetting the chip, as
the former causes firmware commands to be issued which will time out
once the chip has been reset.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: prevent crash in ->configure_filter() if no interface was added
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: call pci_unmap_single() before accessing command structure again
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: add various missing GET_HW_SPEC endian conversions
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: fix NULL pointer dereference on receive out-of-memory
When we go into out-of-memory and fail to allocate skbuffs to
refill the receive ring with, rxq_process can end up running into
a receive ring entry that is marked as host-owned but doesn't have
an associated skbuff. If this happens, we must break out of the
rx processing loop instead of trying to process the descriptor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[S390] kernel: Storing machine flags early in lowcore
Currently, the machine_flags are stored late in the startup
initialization which results in failing machine type checks
(e.g. for MACHINE_IS_VM).
To allow these checks, store the machine flags in the lowcore
when the machine type has been detected.
Steven Rostedt [Thu, 6 Aug 2009 23:53:18 +0000 (19:53 -0400)]
tracing: Fix recordmcount.pl to handle sections with only weak functions
Roland Dreier found that a section that contained only a weak
function in one of the staging drivers and this caused
recordmcount.pl to spit out a warning and fail.
Although it is strange that a driver would have a weak function, and
this function only be used in one place, it should not be something
to make recordmcount.pl fail.
This patch fixes the issue in a simple manner: if only weak
functions exist in a section, then that section will not be
recorded.
Reported-by: Roland Dreier <rdreier@cisco.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
projects / mirror_ubuntu-eoan-kernel.git / log