Arnd Bergmann [Fri, 15 Feb 2019 14:37:07 +0000 (15:37 +0100)]
Merge tag 'hisi-arm64-dt-for-5.1v2' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.1
* Hi6220 SoC and related boards:
- Add DMA entries to enable DMA for Bluetooth transfers
- Add power-on delay to make wifi stable
- Revert HS200 mode to avoid eMMC controller resets and block read failures
* Hi3660 SoC and related boards:
- Fix SD card detection via setting cd-gpios correctly
* Hi3798 SoC and related boards:
- Fix malformed SPDX license identifier
* tag 'hisi-arm64-dt-for-5.1v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hikey: Revert "Enable HS200 mode on eMMC"
arm64: dts: hikey: Give wifi some time after power-on
arm64: dts: hi3798cv200: fix malformed SPDX license identifier
arm64: dts: hikey960: fix SDcard detection
arm64: dts: hikey: Add DMA entries for Bluetooth UART
Arnd Bergmann [Fri, 15 Feb 2019 14:29:18 +0000 (15:29 +0100)]
Merge tag 'lpc32xx-dt-for-5.1' of https://github.com/vzapolskiy/linux-lpc32xx into arm/dt
ARM: lpc32xx: devicetree updates for v5.1
Here are the changes for ARM NXP LPC32xx and ARM NXP LPC18xx/LPC43xx
devicetree files:
* added dts file for MYIR Tech MYD-LPC4357 development board,
* two missing properties are added to LPC32xx keypad controller device
tree node, this fixes a long-standing problem with its initialization,
* LPC32xx PL11x LCD controller device node got corrected properties,
which allows to use it with a new PL11x DRM driver,
* output voltage level on one of Phytec phyCORE-LPC3250 fixed regulators
is corrected, the fix is needed to remove duplicating platform data,
* Phytec phyCORE-LPC3250 board gets a description of a kit LCD panel,
this completes setup of CLCD device tree node for the board,
* added unit addresses to memory device nodes on EA and Phytec boards,
* fixes of ordinary warnings in dts formatting like leading zeroes,
unused address and size cell properties and so on.
* tag 'lpc32xx-dt-for-5.1' of https://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: ea3250: beautify gpio keys children nodes
ARM: dts: lpc32xx: ea3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: add unit address to memory device node
ARM: dts: lpc32xx: phy3250: setup LCD controller to panel interface
ARM: dts: lpc32xx: phy3250: remove regulators umbrella device node
ARM: dts: lpc32xx: phy3250: fix SD card regulator voltage
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller clocks property
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller variant
ARM: dts: lpc32xx: reparent keypad controller to SIC1
ARM: dts: lpc32xx: add required clocks property to keypad device node
ARM: dts: Add DT for MYIR Tech MYD-LPC4357 Development Board
ARM: dts: lpc32xx: Remove leading 0x and 0s from bindings notation
ARM: dts: lpc435x: remove address and size cells from gpio-keys-polled nodes
Arnd Bergmann [Fri, 15 Feb 2019 13:49:40 +0000 (14:49 +0100)]
Merge tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.1, please pull the following:
- Dan relicenses the Luxul DTS files to GPL 2.0+/MIT
- Hao adds support for the Phicomm K3 which is a BCM4709 SoC with dual
BCM4366 radio
- Stefan adds support for the Raspberry Pi A+: binding and DTS files. He
also provides a bunch of DTC warning fixes for the different RPi DTS(i)
files and adds support for missing GPIO lines on RPi 2/3
* tag 'arm-soc/for-5.1/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
ARM: dts: bcm283x: Add missing GPIO line names
ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED
ARM: dts: bcm2837-rpi-3-b: Use consistent label for HDMI hotplug
ARM: dts: bcm2835: Fix labels for GPIO 0,1
ARM: dts: bcm2835-rpi: Drop unnecessary #address-cells/#size-cells
ARM: dts: bcm283x: Fix DTC warning for memory node
ARM: dts: add Raspberry Pi 3 A+
dt-bindings: bcm: Add Raspberry Pi 3 A+
ARM: dts: BCM5301X: Add basic DT for Phicomm K3
ARM: dts: BCM53573: Relicense Luxul files to the GPL 2.0+ / MIT
Arnd Bergmann [Fri, 15 Feb 2019 13:48:24 +0000 (14:48 +0100)]
Merge tag 'samsung-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.1
1. Extend support for Aries family of mobile devices (e.g. Samsung
Galaxy S) based on S5Pv210 SoC: DRM Rotator, FIMD, PWM vibrator,
power off, touchscreen, Broadcom BCM4329 Bluetooth and cpufreq.
2. Remove hardcoded bootargs on Galaxy S family (proper support in
U-Boot).
3. Fix minor DTC warnings.
4. Fix Exynos4412 Odroid X2/U3 conflicting eMMC GPIO settings and regulator
properties.
5. Fix the eMMC RTSN pin breaking proper reboot on X2.
* tag 'samsung-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix pinctrl definition for eMMC RTSN line on Odroid X2/U3
ARM: dts: exynos: Fix eMMC regulator properties on Odroid U3 boards
ARM: dts: exynos: Fix conflicting fixed-regulator GPIO flags and properties
ARM: dts: s3c2416: Fix xti node's missing reg property warning
ARM: dts: s5pv210: Fix onenand's unit address format warning
ARM: dts: s5pv210: Add DMC nodes
ARM: dts: s5pv210: Add support for more devices present on Aries
ARM: dts: s5pv210: Add reserved memory for MFC on Aries
ARM: dts: s5pv210: Remove hardcoded bootargs on Galaxy S and Fascinate 4G
ARM: dts: s5pv210: Use correct fimd variant
ARM: dts: s5pv210: Add node for exynos-rotator
Arnd Bergmann [Fri, 15 Feb 2019 13:47:25 +0000 (14:47 +0100)]
Merge tag 'stm32-dt-for-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.1, round 1
Highlights:
----------
MPU part:
-Enable Digital Thermal Sensor (dts) on stm32mp157c-ed1 (and so ev1).
MCU part:
-Add SPI support on stm32f429 SOC (4 SPIs instances).
* tag 'stm32-dt-for-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Enable thermal sensor support on STM32MP157c-ed1
ARM: dts: stm32: add SPI support on STM32F429 SoC
Arnd Bergmann [Fri, 15 Feb 2019 13:36:29 +0000 (14:36 +0100)]
Merge tag 'v5.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New boards are the Rock Pi 4, NanoPC-T4 and NanoPi-M4, with the last
two being part of a family and sharing bigger parts of the devicetree.
rk3328 got sound-related upgrades and a wider patch drops mmc display-wp
fields from nodes which shouldn't use it.
* tag 'v5.1-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: clean up the abuse of disable-wp
arm64: dts: rockchip: 'Fix' nanopi4 uSD card detect
arm64: dts: rockchip: Add NanoPC-T4 IR receiver
arm64: dts: rockchip: Refine nanopi4 differences
arm64: dts: rockchip: Add DT for NanoPi M4
arm64: dts: rockchip: add ROCK Pi 4 DTS support
arm64: dts: rockchip: Add devicetree for NanoPC-T4
arm64: dts: rockchip: enable analog audio node for rock64
arm64: dts: rockchip: move rk3328 #sound-dai-cells to the soc dtsi
arm64: dts: rockchip: add rk3328 ACODEC node
Arnd Bergmann [Fri, 15 Feb 2019 13:07:05 +0000 (14:07 +0100)]
Merge tag 'v5.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New board the Elgin-R1 based on the rv1108 soc and a number of small
improvements for rv1108 as well. RK3066 got support for the core
display components and the Edison tablet got its touchscreen added.
Apart from that a wider fix to drop display-wp usage from places where
it shouldn't be used, a pin fix for Edison and a cleanup to prevent
rk3036 board from defining sound-dai-cells for core components in
each board separately.
* tag 'v5.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: clean up the abuse of disable-wp
ARM: dts: rv1108: Add support for rv1108-elgin-r1 board
dt-bindings: Add vendor prefix for elgin
ARM: dts: rockchip: rv1108: Add spim0 and spim1 pinctrl groups
ARM: dts: rockchip: Add missing dma-names SPI support for rv1108
ARM: dts: rockchip: add rk3066 vop display nodes
ARM: dts: rockchip: add focaltech touchscreen to rk3188-bqedison2qc
ARM: dts: rockchip: fix cif1_pdn pin on rk3188-bqedison2qc
ARM: dts: rockchip: add HCLK_HDMI to rk3066 vio power-domain
ARM: dts: rockchip: move rk3036 i2s sound-dail-cells into soc dtsi
Arnd Bergmann [Fri, 15 Feb 2019 13:02:53 +0000 (14:02 +0100)]
Merge tag 'am654-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
AM65x DT changes for v5.1. Includes:
- EMMC support for am654-evm board
* tag 'am654-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-am654-base-board: Add eMMC Support
arm64: dts: ti: k3-am654: Add Support for eMMC host controller
Arnd Bergmann [Fri, 15 Feb 2019 12:58:06 +0000 (13:58 +0100)]
Merge tag 'omap-for-v5.1/dt-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
dts updates for ti81xx for v5.1 merge window
Two changes to add support for McGill University's IceBoard telescope
ARM + FPGA instrumentation board. This board is used for several
telescopes around the world, see the related device tree commit for
some interesting links for more information.
Note that these changes are based on the related ti81xx soc changes.
* tag 'omap-for-v5.1/dt-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Adds device tree file for McGill's IceBoard, based on TI AM3874
ARM: dts: ti81xx: Add dts boilerplate for all GPIO and SPI peripherals
Arnd Bergmann [Fri, 15 Feb 2019 12:57:17 +0000 (13:57 +0100)]
Merge tag 'omap-for-v5.1/soc-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
SoC updates for ti81xx for v5.1 merge window
Two changes to add legacy hwmod data for gpio and spi peripherals on
ti81xx. We have not yet updated ti81xx to probe devices with ti-sysc
interconnect target module driver, so these changes are still needed
to make devices usable for the related device tree changes.
* tag 'omap-for-v5.1/soc-ti-81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: ti81xx: Add hwmod boilerplate for all GPIO and SPI peripherals
ARM: ti81xx: Move I2C entries in omap_hwmod_81xx to maintain grouping
Jan Kiszka [Thu, 24 Jan 2019 07:52:33 +0000 (08:52 +0100)]
arm64: dts: hikey: Give wifi some time after power-on
Somewhere along recent changes to power control of the wl1835, power-on
became very unreliable on the hikey, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms, the
hikey would already be happy with 1 ms. Still, we use the safer 10 ms,
like on the Ultra96.
ARM: dts: lpc32xx: ea3250: beautify gpio keys children nodes
Regarding the 'gpio_keys' device node a dtc reports a couple of
warnings:
Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Warning (unit_address_vs_reg): /gpio_keys/button@21: node has
a unit name, but no reg property
The change fixes these issues and adds empty lines between adjacent
children device nodes. The device node itself is renamed by substituting
an underscore by hyphen to follow the standard naming convention
of device tree nodes.
ARM: dts: lpc32xx: phy3250: setup LCD controller to panel interface
The change adds description of Sharp LQ035Q7DB03 3.5" 320x240 TFT panel,
which is connected to Phytec phyCORE-LPC3250 board, ARM PrimeCell PL111
LCD controller on NXP LPC3250 SoC gets its configuration appropriately
to support graphics output to the panel.
The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
ARM: dts: lpc32xx: phy3250: fix SD card regulator voltage
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller clocks property
The originally added ARM PrimeCell PL111 clocks property misses
the required "clcdclk" clock, which is the same as a clock to enable
the LCD controller on NXP LPC3230 and NXP LPC3250 SoCs.
Fixes: 93898eb775e5 ("arm: dts: lpc32xx: add clock properties to device nodes") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller variant
ARM PrimeCell PL111 LCD controller is found on On NXP LPC3230
and LPC3250 SoCs variants, the original reference in compatible
property to an older one ARM PrimeCell PL110 is invalid.
Fixes: e04920d9efcb3 ("ARM: LPC32xx: DTS files for device tree conversion") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM: dts: lpc32xx: reparent keypad controller to SIC1
After switching to a new interrupt controller scheme by separating SIC1
and SIC2 from MIC interrupt controller just one SoC keypad controller
was not taken into account, fix it now:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:524 irq_domain_associate+0x50/0x1b0
error: hwirq 0x36 is too large for interrupt-controller@40008000
...
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Fixes: 9b8ad3fb81ae ("ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org> Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org>
Stefan Wahren [Sat, 19 Jan 2019 16:35:47 +0000 (17:35 +0100)]
ARM: dts: bcm2835-rpi-zero-w: Drop unnecessary pinctrl
There is no need to specify a pinctrl for the reset GPIO. So we better
remove this avoid a potential conflict between pinctrl and pwrseq
after the pinmux driver has been changed to strict:
pinctrl-bcm2835 20200000.gpio: pin gpio41 already requested by wifi-pwrseq;
cannot claim for pinctrl-bcm2835:499
pinctrl-bcm2835 20200000.gpio: pin-41 (pinctrl-bcm2835:499) status -22
pwrseq_simple: probe of wifi-pwrseq failed with error -22
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net>
Stefan Wahren [Tue, 1 Jan 2019 17:29:08 +0000 (18:29 +0100)]
ARM: dts: bcm283x: Add missing GPIO line names
The GPIO sysfs is deprecated and disabled in the defconfig files.
So in order to motivate the usage of the new GPIO character device API
add the missing GPIO line names for Raspberry Pi 2 and 3. In the lack
of full schematics i would leave all undocumented pins as unnamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Eric Anholt <eric@anholt.net>
Stefan Wahren [Thu, 10 Jan 2019 19:22:55 +0000 (20:22 +0100)]
ARM: dts: bcm2837-rpi-3-b-plus: Clarify label for STATUS_LED
The RPI 3 B+ provides control to both LEDs (PWR and ACT). So append
the first letter of the LED color (like in the schematics) in order
to clarify this.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Eric Anholt <eric@anholt.net>
Stefan Wahren [Sun, 30 Dec 2018 16:28:35 +0000 (17:28 +0100)]
ARM: dts: bcm2835: Fix labels for GPIO 0,1
According to the schematics for all RPis with a 40 pin header,
the GPIOs 0 and 1 are labeled as ID_SD and ID_SC. In order to
clarify that is a I2C bus, append the third letter.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net>
Hao Dong [Sun, 20 Jan 2019 22:33:27 +0000 (23:33 +0100)]
ARM: dts: BCM5301X: Add basic DT for Phicomm K3
This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
a PIC microcontroller, which is in turn wired to UART1 of main board.
Vincent Guittot [Mon, 14 Jan 2019 08:24:34 +0000 (09:24 +0100)]
arm64: dts: hikey960: fix SDcard detection
The SDcard detection of hikey960 is active low so cd-inverted is wrong.
Instead of adding cd-inverted, we should better set correctly cd-gpios
to use GPIO_ACTIVE_LOW.
Arnd Bergmann [Wed, 30 Jan 2019 21:36:42 +0000 (22:36 +0100)]
Merge tag 'juno-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/fast models updates for v5.1
1. Support for Fixed Virtual Platforms(FVP) Base RevC model to enable
development of software around the new features available
2. Addition of dynamic-power-coefficient information for CPUs on Juno
3. Miscellaneous changes like re-ordering device nodes, using existing
macros for GIC flags in interrupt-maps and using list instead of
tuple(which is wrong but works as number of interrupt cells is 1)
for mmci interrupts
* tag 'juno-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add cpu dynamic-power-coefficient information
arm64: dts: fast models: Add DTS fo Base RevC FVP
arm64: dts: juno/fast models: sort couple of device nodes
arm64: dts: models: use list instead of tuple for mmci interrupts
arm64: dts: juno/fast models: using GIC macros instead of hardcoded values
Arnd Bergmann [Wed, 30 Jan 2019 21:34:57 +0000 (22:34 +0100)]
Merge tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv7 Vexpress updates for v5.1
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
* tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress-v2p-ca15_a7: Add cpu dynamic-power-coefficient information
ARM: dts: vexpress: use list instead of tuple for mmci interrupts
ARM: dts: mps2: use list instead of tuple for uart interrupts
Arnd Bergmann [Wed, 30 Jan 2019 16:57:26 +0000 (17:57 +0100)]
Merge tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT64 changes for 5.1
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
* tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable A64 timer workaround
arm64: dts: allwinner: a64: Fix a typo
arm64: dts: allwinner: a64: Add PMU node
Arnd Bergmann [Wed, 30 Jan 2019 16:55:57 +0000 (17:55 +0100)]
Merge tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.1
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
* tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i-a23-q8: Set compatible string for LCD panel
ARM: dts: sun8i-q8-common: Enable display pipeline with RGB LCD panel
ARM: dts: sun8i-a23: Add compatible strings to display pipeline device nodes
ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address
ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes
ARM: dts: sun4i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sunxi: bananapi-m2-plus: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator definitions
ARM: dts: sun8i: r40: Add pinmux setting for CLK_OUT_A
ARM: dts: sun8i: r40: Add pinmux settings for UART3 on PG pingroup
ARM: dts: sun7i: bananapi: Add GPIO banks regulators
ARM: dts: sun4i-a10: Add PMU node
Arnd Bergmann [Wed, 30 Jan 2019 16:53:27 +0000 (17:53 +0100)]
Merge tag 'renesas-arm64-dt-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/dt
Renesas ARM64 Based SoC DT Updates for v5.1
R-Car H3 (r8a7795) SoC
- Sort i2c and pciec0 nodes within soc node
R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Remove BUSIF0 settings from rcar_sound,ssi
R-Car M3-W (r8a7796) based Salvator-XS board
- Convert to new LVDS DT bindings
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) based ULCB boards
- Use audio-graph-card to allow secondary sound device on kingfisher
daugher board
- Add HDMI sound support
Kingfisher daughterboard for R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N
(r8a77965) based ULCB boards
- Add pcm3168 sound codec
R-Car E3 (r8a77990) SoC
- Enable DMA for SCIF2
R-Car E3 (r8a77990) based Ebisu board
- HS400 for onboard eMMC
- Use simple-audio-card rather than simple-scu-audio-card
- Correct EthernetAVB phy mode as rgmii
- Add backlight and follow-up to correct duplicate regulator number
R-Car V3M (r8a77970) based v3msk starter kit
- Specify EtherAVB PHY IRQ now that GPIO support is present
R-Car D3 (r8a77995) based draak board
- Set better backlight levels
RZ/G2M (r8a774a1) SoC
- Correct hsusb reg size
RZ/G2E (r8a774c0) SoC
- Intial SoC DT
- Add: and SYS-DMAC controller, SCIF, HSCIF, INTC-EX
PFC, GPIO, Ethernet AVB, watchdog, secondary CA3 core, SDHI,
I2C, IIC-DVFS, IPMU, CAN, thermal, MSIOF, audio, PWM, display output,
USB2.0, USB-DMAC, HSUSB, USB3.0, IPMMU, PCIe, VIN and CSI-2 support
- A follow-up patch included in this pull-request enables DMA for SCIF2
so that DMA is enabled for all SCIF nodes
* tag 'renesas-arm64-dt-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (44 commits)
arm64: dts: renesas: r8a77990: ebisu: Enable HS400 of SDHI3
arm64: dts: renesas: r8a77990: Enable DMA for SCIF2
arm64: dts: renesas: r8a774c0: Enable DMA for SCIF2
arm64: dts: renesas: r8a77990: ebisu: Fix backlight regulator numbering
arm64: dts: renesas: v3msk: specify EtherAVB PHY IRQ
arm64: dts: renesas: r8a77990-ebisu: use simple-audio-card
arm64: dts: renesas: r8a7796: remove BUSIF0 settings from rcar_sound,ssi
arm64: dts: renesas: r8a7795: remove BUSIF0 settings from rcar_sound,ssi
arm64: dts: renesas: ulcb-kf: add pcm3168 sound codec
arm64: dts: renesas: ulcb: add HDMI sound support
arm64: dts: renesas: ulcb: use audio-graph-card
arm64: dts: renesas: r8a7796: salvator-xs: Convert to new LVDS DT bindings
arm64: dts: renesas: r8a77990: Sort i2c nodes within soc node
arm64: dts: renesas: r8a77990: sort pciec0 node within soc node
arm64: dts: renesas: r8a774a1: Fix hsusb reg size
arm64: dts: renesas: r8a774c0: Add VIN and CSI-2 device nodes
arm64: dts: renesas: r8a774c0: Add PCIe device node
arm64: dts: renesas: r8a774c0: Connect RZ/G2E Audio-DMAC to IPMMU
arm64: dts: renesas: r8a774c0: Connect RZ/G2E AVB to IPMMU
arm64: dts: renesas: r8a774c0: Connect RZ/G2E SYS-DMAC to IPMMU
...
Arnd Bergmann [Wed, 30 Jan 2019 16:52:26 +0000 (17:52 +0100)]
Merge tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
This updates the Integrator DTS files with the device
tree nodes required by the DRM driver.
* tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Augment panel setting for Integrator/CP
Rob Herring [Mon, 14 Jan 2019 17:45:33 +0000 (11:45 -0600)]
arm64: dts: Remove inconsistent use of 'arm,armv8' compatible string
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Nishanth Menon <nm@ti.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Chanho Min <chanho.min@lge.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Tero Kristo <t-kristo@ti.com> Acked-by: Wei Xu <xuwei5@hisilicon.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Acked-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Scott Branden <scott.branden@broadcom.com> Acked-by: Kevin Hilman <khilman@baylibre.com> Acked-by: Chunyan Zhang <zhang.lyra@gmail.com> Acked-by: Robert Richter <rrichter@cavium.com> Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Wed, 9 Jan 2019 16:26:14 +0000 (10:26 -0600)]
ARM: dts: Kill off skeleton{64}.dtsi
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 30 Jan 2019 16:26:33 +0000 (17:26 +0100)]
Merge tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v4.21, round 1
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
* tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add thermal sensor support on STM32MP157c
ARM: dts: stm32: add can1 sleep pins muxing on stm32mp157c-ev1 board
ARM: dts: stm32: add can1 sleep pins muxing
ARM: dts: stm32: change CAN RAM mapping on stm32mp157c
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ev1
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ed1
ARM: dts: stm32: Add dmas to timer on stm32mp157c
Dietmar Eggemann [Mon, 28 Jan 2019 16:55:21 +0000 (16:55 +0000)]
arm64: dts: juno: Add cpu dynamic-power-coefficient information
A CPUfreq driver, like the scpi driver used on Juno boards, which
provide the Energy Model with power cost information via the PM_OPP
of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Since DVFS is broken on Juno r1, no dynamic-power-coefficient
information has been added to its dts file.
Dietmar Eggemann [Mon, 28 Jan 2019 16:55:22 +0000 (16:55 +0000)]
arm: dts: vexpress-v2p-ca15_a7: Add cpu dynamic-power-coefficient information
A CPUfreq driver, like the ARM big.LITTLE driver used on the TC2 board,
which provide the Energy Model with power cost information via the
PM_OPP of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Fixed Virtual Platforms(FVP) Base RevC model is an emulated Arm platform
with GICv3, PCIe, SMMUv3 and various other features. These are available
free of charge on the Arm Community website at Arm Development
Platforms[1].
It resembles the Foundation Platform, which is a simple FVP that
includes an Armv8‑A AEM processor model but this has two cluster of four
cores, a CCI-550 interconnect, an SMMU and two PCI devices.
In order to enable development of software, let's add a description of
the Revison C version of Base platform.
The documentation for this FVP model is available @[2] for reference.
Sudeep Holla [Fri, 25 Jan 2019 17:50:03 +0000 (17:50 +0000)]
arm64: dts: models: use list instead of tuple for mmci interrupts
RTSM/FVP vexpress motherboard model MMCI requires dedicated interrupts
for CMD and PIO, which obviously should be expressed as a list. Current
form uses tuple and it works fine since interrupt-cells equal to 1.
Acked-by: Liviu Dudau <liviu.dudau@arm.com> Reported-by: Vladimir Murzin <vladimir.murzin@arm.com> Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Sudeep Holla [Fri, 25 Jan 2019 17:49:53 +0000 (17:49 +0000)]
arm64: dts: juno/fast models: using GIC macros instead of hardcoded values
There are macros that exist to indicate the GIC specific flags and
custom cell values as per the GIC DT bindings. It's used in most of the
places in these DTS files but not all. To maintain consistency, lets
use the macros at all the places.
Since DTC doesn't even warn is any cells are missing, it's very hard to
debug if that's the case. Changing to use macros avoids missing cells/
columns.
Linus Torvalds [Sun, 27 Jan 2019 20:02:00 +0000 (12:02 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the swapped outb() parameters in the KASLR code
- Fix the PKEY handling at fork which missed to preserve the pkey
state for the child. Comes with a test case to validate that.
- Fix the entry stack handling for XEN PV to respect that XEN PV
systems enter the function already on the current thread stack and
not on the trampoline.
- Fix kexec load failure caused by using a stale value when the
kexec_buf structure is reused for subsequent allocations.
- Fix a bogus sizeof() in the memory encryption code
- Enforce PCI dependency for the Intel Low Power Subsystem
- Enforce PCI_LOCKLESS_CONFIG when PCI is enabled"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Select PCI_LOCKLESS_CONFIG if PCI is enabled
x86/entry/64/compat: Fix stack switching for XEN PV
x86/kexec: Fix a kexec_file_load() failure
x86/mm/mem_encrypt: Fix erroneous sizeof()
x86/selftests/pkeys: Fork() to check for state being preserved
x86/pkeys: Properly copy pkey state at fork()
x86/kaslr: Fix incorrect i8254 outb() parameters
x86/intel/lpss: Make PCI dependency explicit
Linus Torvalds [Sun, 27 Jan 2019 19:57:46 +0000 (11:57 -0800)]
Merge branch 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 timer fixes from Thomas Gleixner:
"Two commits which were missed to be sent during the merge window.
- The TSC calibration fix turns out to be more urgent as recent
Skylake-X systems seem to have massive trouble with calibration
disturbance. This should go back into stable for that reason and it
the risk of breakage is rather low.
- Drop an unused define"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Remove unused FSEC_PER_NSEC define
x86/tsc: Make calibration refinement more robust
Linus Torvalds [Sun, 27 Jan 2019 19:55:06 +0000 (11:55 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Glexiner:
"A single regression fix to address the unintended breakage of posix
cpu timers.
This is caused by a new sanity check in the common code, which fails
for posix cpu timers under certain conditions because the posix cpu
timer code never updates the variable which is checked"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Unbreak timer rearming
Linus Torvalds [Sun, 27 Jan 2019 19:25:38 +0000 (11:25 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small set of fixes for the interrupt subsystem:
- Fix a double increment in the irq descriptor allocator which
resulted in a sanity check only being done for every second
affinity mask
- Add a missing device tree translation in the stm32-exti driver.
Without that the interrupt association is completely wrong.
- Initialize the mutex in the GIC-V3 MBI driver
- Fix the alignment for aliasing devices in the GIC-V3-ITS driver so
multi MSI allocations work correctly
- Ensure that the initial affinity of a interrupt is not empty at
startup time.
- Drop bogus include in the madera irq chip driver
- Fix KernelDoc regression"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size
genirq/irqdesc: Fix double increment in alloc_descs()
genirq: Fix the kerneldoc comment for struct irq_affinity_desc
irqchip/madera: Drop GPIO includes
irqchip/gic-v3-mbi: Fix uninitialized mbi_lock
irqchip/stm32-exti: Add domain translate function
genirq: Make sure the initial affinity is not empty
Linus Torvalds [Sun, 27 Jan 2019 17:21:00 +0000 (09:21 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Quite a few fixes for x86: nested virtualization save/restore, AMD
nested virtualization and virtual APIC, 32-bit fixes, an important fix
to restore operation on older processors, and a bunch of hyper-v
bugfixes. Several are marked stable.
There are also fixes for GCC warnings and for a GCC/objtool interaction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Mark expected switch fall-throughs
KVM: x86: fix TRACE_INCLUDE_PATH and remove -I. header search paths
KVM: selftests: check returned evmcs version range
x86/kvm/hyper-v: nested_enable_evmcs() sets vmcs_version incorrectly
KVM: VMX: Move vmx_vcpu_run()'s VM-Enter asm blob to a helper function
kvm: selftests: Fix region overlap check in kvm_util
kvm: vmx: fix some -Wmissing-prototypes warnings
KVM: nSVM: clear events pending from svm_complete_interrupts() when exiting to L1
svm: Fix AVIC incomplete IPI emulation
svm: Add warning message for AVIC IPI invalid target
KVM: x86: WARN_ONCE if sending a PV IPI returns a fatal error
KVM: x86: Fix PV IPIs for 32-bit KVM host
x86/kvm/hyper-v: recommend using eVMCS only when it is enabled
x86/kvm/hyper-v: don't recommend doing reset via synthetic MSR
kvm: x86/vmx: Use kzalloc for cached_vmcs12
KVM: VMX: Use the correct field var when clearing VM_ENTRY_LOAD_IA32_PERF_GLOBAL_CTRL
KVM: x86: Fix single-step debugging
x86/kvm/hyper-v: don't announce GUEST IDLE MSR support
Linus Torvalds [Sun, 27 Jan 2019 17:11:51 +0000 (09:11 -0800)]
Merge tag 'libnvdimm-fixes-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for namespace label support for non-Intel NVDIMMs that implement
the ACPI standard label method.
This has apparently never worked and could wait for v5.1. However it
has enough visibility with hardware vendors [1] and distro bug
trackers [2], and low enough risk that I decided it should go in for
-rc4. The other fixups target the new, for v5.0, nvdimm security
functionality. The larger init path fixup closes a memory leak and a
potential userspace lockup due to missed notifications.
These have all soaked in -next for a week with no reported issues.
Summary:
- Fix support for NVDIMMs that implement the ACPI standard label
methods.
- Fix error handling for security overwrite (memory leak / userspace
hang condition), and another one-line security cleanup"
* tag 'libnvdimm-fixes-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
acpi/nfit: Fix command-supported detection
acpi/nfit: Block function zero DSMs
libnvdimm/security: Require nvdimm_security_setup_events() to succeed
nfit_test: fix security state pull for nvdimm security nfit_test
1) Count ttl-dropped frames properly in mac80211, from Bob Copeland.
2) Integer overflow in ktime handling of bcm can code, from Oliver
Hartkopp.
3) Fix RX desc handling wrt. hw checksumming in ravb, from Simon
Horman.
4) Various hash key fixes in hv_netvsc, from Haiyang Zhang.
5) Use after free in ax25, from Eric Dumazet.
6) Several fixes to the SSN support in SCTP, from Xin Long.
7) Do not process frames after a NAPI reschedule in ibmveth, from
Thomas Falcon.
8) Fix NLA_POLICY_NESTED arguments, from Johannes Berg.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
qed: Revert error handling changes.
cfg80211: extend range deviation for DMG
cfg80211: reg: remove warn_on for a normal case
mac80211: Add attribute aligned(2) to struct 'action'
mac80211: don't initiate TDLS connection if station is not associated to AP
nl80211: fix NLA_POLICY_NESTED() arguments
ibmveth: Do not process frames after calling napi_reschedule
net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP
net: usb: asix: ax88772_bind return error when hw_reset fail
MAINTAINERS: Update cavium networking drivers
net/mlx4_core: Fix error handling when initializing CQ bufs in the driver
net/mlx4_core: Add masking for a few queries on HCA caps
sctp: set flow sport from saddr only when it's 0
sctp: set chunk transport correctly when it's a new asoc
sctp: improve the events for sctp stream adding
sctp: improve the events for sctp stream reset
ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnel
ax25: fix possible use-after-free
sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe
hv_netvsc: fix typos in code comments
...
Linus Torvalds [Sat, 26 Jan 2019 23:38:22 +0000 (15:38 -0800)]
Merge tag '5.0-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
"A set of small smb3 fixes, some fixing various crediting issues
discovered during xfstest runs, five for stable"
* tag '5.0-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: print CIFSMaxBufSize as part of /proc/fs/cifs/DebugData
smb3: add credits we receive from oplock/break PDUs
CIFS: Fix mounts if the client is low on credits
CIFS: Do not assume one credit for async responses
CIFS: Fix credit calculations in compound mid callback
CIFS: Fix credit calculation for encrypted reads with errors
CIFS: Fix credits calculations for reads with errors
CIFS: Do not reconnect TCP session in add_credits()
smb3: Cleanup license mess
CIFS: Fix possible hang during async MTU reads and writes
cifs: fix memory leak of an allocated cifs_ntsd structure
Linus Torvalds [Sat, 26 Jan 2019 23:03:43 +0000 (15:03 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
Linus Torvalds [Sat, 26 Jan 2019 20:42:41 +0000 (12:42 -0800)]
Merge tag 'for-linus-20190125' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes for this release. This contains:
- Silence sparse rightfully complaining about non-static wbt
functions (Bart)
- Fixes for the zoned comments/ioctl documentation (Damien)
- direct-io fix that's been lingering for a while (Ernesto)
- cgroup writeback fix (Tejun)
- Set of NVMe patches for nvme-rdma/tcp (Sagi, Hannes, Raju)
- Block recursion tracking fix (Ming)
- Fix debugfs command flag naming for a few flags (Jianchao)"
* tag 'for-linus-20190125' of git://git.kernel.dk/linux-block:
block: Fix comment typo
uapi: fix ioctl documentation
blk-wbt: Declare local functions static
blk-mq: fix the cmd_flag_name array
nvme-multipath: drop optimization for static ANA group IDs
nvmet-rdma: fix null dereference under heavy load
nvme-rdma: rework queue maps handling
nvme-tcp: fix timeout handler
nvme-rdma: fix timeout handler
writeback: synchronize sync(2) against cgroup writeback membership switches
block: cover another queue enter recursion via BIO_QUEUE_ENTERED
direct-io: allow direct writes to empty inodes
ARM: dts: lpc435x: remove address and size cells from gpio-keys-polled nodes
The change removes redundant #address-cells and #size-cells properties from
gpio-keys-polled compatible device nodes found in lpc4357-ea4357-devkit and
lpc4350-hitex-eval board DTS files.
Linus Torvalds [Fri, 25 Jan 2019 23:07:03 +0000 (13:07 -1000)]
Merge tag 'mmc-v5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- sdhci-acpi: Fixup build dependency for PCI
- sdhci-omap: Resolve Kconfig warnings on keystone
- sdhci-iproc: Propagate errors from DT parsing
- meson-gx: Fixup IRQ handling in release callback
- meson-gx: Use signal re-sampling to fixup tuning
- dw_mmc-bluefield: Fix the license information
* tag 'mmc-v5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: dw_mmc-bluefield: : Fix the license information
mmc: meson-gx: enable signal re-sampling together with tuning
mmc: sdhci-iproc: handle mmc_of_parse() errors during probe
mmc: meson-gx: Free irq in release() callback
mmc: host: Fix Kconfig warnings on keystone_defconfig
mmc: sdhci-acpi: Make PCI dependency explicit
Linus Torvalds [Fri, 25 Jan 2019 23:03:34 +0000 (13:03 -1000)]
Merge tag 'char-misc-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes to resolve some
reported issues, as well as a number of binderfs fixups that were
found after auditing the filesystem code by Al Viro. As binderfs
hasn't been in a previous release yet, it's good to get these in now
before the first users show up.
All of these have been in linux-next for a bit with no reported
issues"
* tag 'char-misc-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
i3c: master: Fix an error checking typo in 'cdns_i3c_master_probe()'
binderfs: switch from d_add() to d_instantiate()
binderfs: drop lock in binderfs_binder_ctl_create
binderfs: kill_litter_super() before cleanup
binderfs: rework binderfs_binder_device_create()
binderfs: rework binderfs_fill_super()
binderfs: prevent renaming the control dentry
binderfs: remove outdated comment
binderfs: use __u32 for device numbers
binderfs: use correct include guards in header
misc: pvpanic: fix warning implicit declaration
char/mwave: fix potential Spectre v1 vulnerability
misc: ibmvsm: Fix potential NULL pointer dereference
binderfs: fix error return code in binderfs_fill_super()
mei: me: add denverton innovation engine device IDs
mei: me: mark LBG devices as having dma support
mei: dma: silent the reject message
binderfs: handle !CONFIG_IPC_NS builds
binderfs: reserve devices for initial mount
binderfs: rename header to binderfs.h
...