Andrew Lunn [Wed, 18 Apr 2018 23:02:58 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Add #defines for the GPIO index's
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 18 Apr 2018 23:02:57 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Parse properties directly into bitbang structure
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 18 Apr 2018 23:02:54 +0000 (01:02 +0200)]
net: phy: mdio-gpio: Remove support for IRQs in platform data
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:06 +0000 (15:39 -0700)]
net/ipv6: Fix gfp_flags arg to addrconf_prefix_route
Eric noticed that __ipv6_ifa_notify is called under rcu_read_lock, so
the gfp argument to addrconf_prefix_route can not be GFP_KERNEL.
While scrubbing other calls I noticed addrconf_addr_gen has one
place with GFP_ATOMIC that can be GFP_KERNEL.
Fixes: acb54e3cba404 ("net/ipv6: Add gfp_flags to route add functions") Reported-by: syzbot+2add39b05179b31f912f@syzkaller.appspotmail.com Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:04 +0000 (15:39 -0700)]
net/ipv6: Remove compare of fib6_idev from rt6_duplicate_nexthop
After 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") the comparison of idev does not add value since it
correlates to the nexthop device which is already compared. Remove
the idev comparison.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:03 +0000 (15:39 -0700)]
net/ipv6: Change ip6_route_get_saddr to get dev from route
Prior to 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.
Commit 4832c30d5458 changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change ip6_route_get_saddr can just pass the nexthop
device to ipv6_dev_get_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:39:02 +0000 (15:39 -0700)]
net/ipv6: Remove unnecessary checks on fib6_idev
Prior to 4832c30d5458 ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.
Commit 4832c30d5458 changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change a couple of device checks during route lookups
are no longer needed. Remove them.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 22:38:59 +0000 (15:38 -0700)]
net/ipv6: Rename fib6_info struct elements
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Apr 2018 18:43:15 +0000 (11:43 -0700)]
net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends
After working on IP defragmentation lately, I found that some large
packets defeat CHECKSUM_COMPLETE optimization because of NIC adding
zero paddings on the last (small) fragment.
While removing the padding with pskb_trim_rcsum(), we set skb->ip_summed
to CHECKSUM_NONE, forcing a full csum validation, even if all prior
fragments had CHECKSUM_COMPLETE set.
We can instead compute the checksum of the part we are trimming,
usually smaller than the part we keep.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tracking TCP data delivery and ECN stats
This patch series improve tracking the data delivery status
1. minor improvement on SYN data
2. accounting bytes delivered with CE marks
3. exporting the delivery stats to applications
s.t. users can get better sense of TCP performance at per host,
per connection, and even per application message level.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Export data delivered and delivered with CE marks to
1) SNMP TCPDelivered and TCPDeliveredCE
2) getsockopt(TCP_INFO)
3) Timestamping API SOF_TIMESTAMPING_OPT_STATS
Note that for SCM_TSTAMP_ACK, the delivery info in
SOF_TIMESTAMPING_OPT_STATS is reported before the info
was fully updated on the ACK.
These stats help application monitor TCP delivery and ECN status
on per host, per connection, even per message level.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: track total bytes delivered with ECN CE marks
Introduce a new delivered_ce stat in tcp socket to estimate
number of packets being marked with CE bits. The estimation is
done via ACKs with ECE bit. Depending on the actual receiver
behavior, the estimation could have biases.
Since the TCP sender can't really see the CE bit in the data path,
so the sender is technically counting packets marked delivered with
the "ECE / ECN-Echo" flag set.
With RFC3168 ECN, because the ECE bit is sticky, this count can
drastically overestimate the nummber of CE-marked data packets
With DCTCP-style ECN this should be reasonably precise unless there
is loss in the ACK path, in which case it's not precise.
With AccECN proposal this can be made still more precise, even in
the case some degree of ACK loss.
However this is sender's best estimate of CE information.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: better delivery accounting for SYN-ACK and SYN-data
the tcp_sock:delivered has inconsistent accounting for SYN and FIN.
1. it counts pure FIN
2. it counts pure SYN
3. it counts SYN-data twice
4. it does not count SYN-ACK
For congestion control perspective it does not matter much as C.C. only
cares about the difference not the aboslute value. But the next patch
would export this field to user-space so it's better to report the absolute
value w/o these caveats.
This patch counts SYN, SYN-ACK, or SYN-data delivery once always in
the "delivered" field.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2) ip6_input_finish()
ipv6_frag_rcv() (lock frag queue spinlock)
ip6_frag_queue()
icmpv6_param_prob() (lock txq->_xmit_lock at some point)
We could add lockdep annotations, but we also can make sure IPv6
calls icmpv6_param_prob() only after the release of the frag queue spinlock,
since this naturally makes frag queue spinlock a leaf in lock hierarchy.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: propogate Hyper-V friendly name into interface alias
This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.
The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.
In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.
The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.
Also requires exporting dev_set_alias in netdev core.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: remove jumbo_tx_csum from chip config struct
According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.
By implementing this rule we can get rid of configuring tx checksumming
support per chip type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000
In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For security reasons since commit ad67b74d2469 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.
When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 19 Apr 2018 01:00:58 +0000 (21:00 -0400)]
Merge branch 'netcp-K2G-SoC-support'
Murali Karicheri says:
====================
Add support for netcp driver on K2G SoC
K2G SoC is another variant of Keystone family of SoCs. This patch
series add support for NetCP driver on this SoC. The QMSS found on
K2G SoC is a cut down version of the QMSS found on other keystone
devices with less number of queues, internal link ram etc. The patch
series has 2 patch sets that goes into the drivers/soc and the
rest has to be applied to net sub system. Please review and merge
if this looks good.
K2G TRM is located at http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Thanks
The boot logs on K2G ICE board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/yvZ6drFhkW/
The boot logs on K2G GP board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/QTr6K7s4Zp/
Also regressed boot on K2HK and K2L EVMs as we have modified GBE
version detection logic (K2E uses same version of NetCP as in K2L.
So regression on one of them is needed).
Boot log on K2L and K2HK EVMs are at
https://pastebin.ubuntu.com/p/N9DBdPjbvR/
This series applies to net-next master branch.
Change history:
v4 - ready for merge to net-next
Folded the series "Add promiscous mode support in k2g network driver"
into this.
Fixed a typo in 5/11 (sgmii to rgmii) based on TI internal comment
Reworked 4/11 and title changed to reflect additional changes to
exclude sgmii configuration code for 2U cpsw. Use IS_SS_ID_2U()
macro for customization.
Added Reviewed-by from Rob Herring against 1/13
v3 - Addressed comments from Andrew Lunn and Grygorii Strashko
against v2.
v2 - Addressed following comments on initial version
- split patch 3/5 to multiple patches from Andrew Lunn
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: k2g: add promiscuous mode support
This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: add api to support set rx mode in netcp modules
This patch adds an API to support setting rx mode in
netcp modules. If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch. Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: use of_get_phy_mode() to support different RGMII modes
The phy used for K2G allows for internal delays to be added optionally
to the clock circuitry based on board desing. To add this support,
enhance the driver to use of_get_phy_mode() to read the phy-mode from
the phy device and pass the same to phy through of_phy_connect().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: re-use stats handling code for 2u hardware
The stats block in 2u cpsw hardware is similar to the one on nu
and hence handle it in a similar way by using a macro that includes
2u hardware as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: add support for handling rgmii link interface
2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: make sgmii configuration conditional
As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: netcp: ethss: use macro for checking ss_version consistently
Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
soc: ti: K2G: provide APIs to support driver probe deferral
This patch provide APIs to allow client drivers to support
probe deferral. On K2G SoC, devices can be probed only
after the ti_sci_pm_domains driver is probed and ready.
As drivers may get probed at different order, any driver
that depends on knav dma and qmss drivers, for example
netcp network driver, needs to defer probe until
knav devices are probed and ready to service. To do this,
add an API to query the device ready status from the knav
dma and qmss devices.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
soc: ti: K2G: enhancement to support QMSS in K2G NAVSS
Navigator Subsystem (NAVSS) available on K2G SoC has a cut down
version of QMSS with less number of queues, internal linking ram
with lesser number of buffers etc. It doesn't have status and
explicit push register space as in QMSS available on other K2 SoCs.
So define reg indices specific to QMSS on K2G. This patch introduces
"ti,66ak2g-navss-qm" compatibility to identify QMSS on K2G NAVSS
and to customize the dts handling code. Per Device manual,
descriptors with index less than or equal to regions0_size is in region 0
in the case of K2 QMSS where as for QMSS on K2G, descriptors with index
less than regions0_size is in region 0. So update the size accordingly in
the regions0_size bits of the linking ram size 0 register.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net/ipv6: Separate data structures for FIB and data path
IPv6 uses the same data struct for both control plane (FIB entries) and
data path (dst entries). This struct has elements needed for both paths
adding memory overhead and complexity (taking a dst hold in most places
but an additional reference on rt6i_ref in a few). Furthermore, because
of the dst_alloc tie, all FIB entries are allocated with GFP_ATOMIC.
This patch set separates FIB entries from dst entries, better aligning
IPv6 code with IPv4, simplifying the reference counting and allowing
FIB entries added by userspace (not autoconf) to use GFP_KERNEL. It is
first step to a number of performance and scalability changes.
The end result of this patch set:
- FIB entries (fib6_info):
/* size: 208, cachelines: 4, members: 25 */
/* sum members: 207, holes: 1, sum holes: 1 */
Versus the the single rt6_info struct today for both paths:
/* size: 320, cachelines: 5, members: 28 */
This amounts to a 35% reduction in memory use for FIB entries and a
25% reduction for dst entries.
With respect to locking FIB entries use RCU and a single atomic
counter with fib6_info_hold and fib6_info_release helpers to manage
the reference counting. dst entries use only the traditional dst
refcounts with dst_hold and dst_release.
FIB entries for host routes are referenced by inet6_ifaddr and
ifacaddr6. In both cases, additional holds are taken -- similar to
what is done for devices.
This set is the first of many changes to improve the scalability of the
IPv6 code. Follow on changes include:
- consolidating duplicate fib6_info references like IPv4 does with
duplicate fib_info
- moving fib6_info into a slab cache to avoid allocation roundups to
power of 2 (the 208 size becomes a 256 actual allocation)
- Allow FIB lookups without generating a dst (e.g., most rt6_lookup
users just want to verify the egress device). Means moving dst
allocation to the other side of fib6_rule_lookup which again aligns
with IPv4 behavior
- using separate standalone nexthop objects which have performance
benefits beyond fib_info consolidation
At this point I am not seeing any refcount leaks or underflows, no
oops or bug_ons, or warnings from kasan, so I think it is ready for
others to beat up on it finding errors in code paths I have missed.
v2 changes
- rebased to top of tree
- improved commit message on patch 7
v1 changes
- rebased to top of tree
- fix memory leak of metrics as noted by Ido
- MTU fixes based on pmtu tests (thanks Stefano Brivio for writing)
RFC v2 changes
- improved commit messages
- move common metrics code from dst.c to net/ipv4/metrics.c (comment
from DaveM)
- address comments from Wei Wang and Martin KaFai Lau (let me know if
I missed something)
- fixes detected by kernel test robots
+ added fib6_metric_set to change metric on a FIB entry which could
be pointing to read-only dst_default_metrics
+ 0day testing found a problem with an intermediate patch; added
dst_hold_safe on rt->from. Code is removed 3 patches later
- allow cacheinfo to handle NULL dst; means only expires is pushed to
userspace
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:25 +0000 (17:33 -0700)]
net/ipv6: separate handling of FIB entries from dst based routes
Last step before flipping the data type for FIB entries:
- use fib6_info_alloc to create FIB entries in ip6_route_info_create
and addrconf_dst_alloc
- use fib6_info_release in place of dst_release, ip6_rt_put and
rt6_release
- remove the dst_hold before calling __ip6_ins_rt or ip6_del_rt
- when purging routes, drop per-cpu routes
- replace inc and dec of rt6i_ref with fib6_info_hold and fib6_info_release
- use rt->from since it points to the FIB entry
- drop references to exception bucket, fib6_metrics and per-cpu from
dst entries (those are relevant for fib entries only)
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:23 +0000 (17:33 -0700)]
net/ipv6: Cleanup exception and cache route handling
IPv6 FIB will only contain FIB entries with exception routes added to
the FIB entry. Once this transformation is complete, FIB lookups will
return a fib6_info with the lookup functions still returning a dst
based rt6_info. The current code uses rt6_info for both paths and
overloads the rt6_info variable usually called 'rt'.
This patch introduces a new 'f6i' variable name for the result of the FIB
lookup and keeps 'rt' as the dst based return variable. 'f6i' becomes a
fib6_info in a later patch which is why it is introduced as f6i now;
avoids the additional churn in the later patch.
In addition, remove RTF_CACHE and dst checks from fib6 add and delete
since they can not happen now and will never happen after the data
type flip.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:22 +0000 (17:33 -0700)]
net/ipv6: Add gfp_flags to route add functions
Most FIB entries can be added using memory allocated with GFP_KERNEL.
Add gfp_flags to ip6_route_add and addrconf_dst_alloc. Code paths that
can be reached from the packet path (e.g., ndisc and autoconfig) or
atomic notifiers use GFP_ATOMIC; paths from user context (adding
addresses and routes) use GFP_KERNEL.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:21 +0000 (17:33 -0700)]
net/ipv6: Create a neigh_lookup for FIB entries
The router discovery code has a FIB entry and wants to validate the
gateway has a neighbor entry. Refactor the existing dst_neigh_lookup
for IPv6 and create a new function that takes the gateway and device
and returns a neighbor entry. Use the new function in
ndisc_router_discovery to validate the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:20 +0000 (17:33 -0700)]
net/ipv6: Move dst flags to booleans in fib entries
Continuing to wean FIB paths off of dst_entry, use a bool to hold
requests for certain dst settings. Add a helper to convert the
flags to DST flags when a FIB entry is converted to a dst_entry.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:19 +0000 (17:33 -0700)]
net/ipv6: Add rt6_info create function for ip6_pol_route_lookup
ip6_pol_route_lookup is the lookup function for ip6_route_lookup and
rt6_lookup. At the moment it returns either a reference to a FIB entry
or a cached exception. To move FIB entries to a separate struct, this
lookup function needs to convert FIB entries to an rt6_info that is
returned to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:18 +0000 (17:33 -0700)]
net/ipv6: Add fib6_null_entry
ip6_null_entry will stay a dst based return for lookups that fail to
match an entry.
Add a new fib6_null_entry which constitutes the root node and leafs
for fibs. Replace existing references to ip6_null_entry with the
new fib6_null_entry when dealing with FIBs.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:17 +0000 (17:33 -0700)]
net/ipv6: move expires into rt6_info
Add expires to rt6_info for FIB entries, and add fib6 helpers to
manage it. Data path use of dst.expires remains.
The transition is fairly straightforward: when working with fib entries,
rt->dst.expires is just rt->expires, rt6_clean_expires is replaced with
fib6_clean_expires, rt6_set_expires becomes fib6_set_expires, and
rt6_check_expired becomes fib6_check_expired, where the fib6 versions
are added by this patch.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:16 +0000 (17:33 -0700)]
net/ipv6: move metrics from dst to rt6_info
Similar to IPv4, add fib metrics to the fib struct, which at the moment
is rt6_info. Will be moved to fib6_info in a later patch. Copy metrics
into dst by reference using refcount.
To make the transition:
- add dst_metrics to rt6_info. Default to dst_default_metrics if no
metrics are passed during route add. No need for a separate pmtu
entry; it can reference the MTU slot in fib6_metrics
- ip6_convert_metrics allocates memory in the FIB entry and uses
ip_metrics_convert to copy from netlink attribute to metrics entry
- the convert metrics call is done in ip6_route_info_create simplifying
the route add path
+ fib6_commit_metrics and fib6_copy_metrics and the temporary
mx6_config are no longer needed
- add fib6_metric_set helper to change the value of a metric in the
fib entry since dst_metric_set can no longer be used
- cow_metrics for IPv6 can drop to dst_cow_metrics_generic
- rt6_dst_from_metrics_check is no longer needed
- rt6_fill_node needs the FIB entry and dst as separate arguments to
keep compatibility with existing output. Current dst address is
renamed to dest.
(to be consistent with IPv4 rt6_fill_node really should be split
into 2 functions similar to fib_dump_info and rt_fill_info)
- rt6_fill_node no longer needs the temporary metrics variable
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:15 +0000 (17:33 -0700)]
net/ipv6: Defer initialization of dst to data path
Defer setting dst input, output and error until fib entry is copied.
The reject path from ip6_route_info_create is moved to a new function
ip6_rt_init_dst_reject with a helper doing the conversion from fib6_type
to dst error.
The remainder of the new ip6_rt_init_dst is an amalgamtion of dst code
from addrconf_dst_alloc and the non-reject path of ip6_route_info_create.
The dst output function is always ip6_output and the input function is
either ip6_input (local routes), ip6_mc_input (multicast routes) or
ip6_forward (anything else).
A couple of places using dst.error are updated to look at rt6i_flags.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:14 +0000 (17:33 -0700)]
net/ipv6: Move nexthop data to fib6_nh
Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:13 +0000 (17:33 -0700)]
net/ipv6: Save route type in rt6_info
The RTN_ type for IPv6 FIB entries is currently embedded in rt6i_flags
and dst.error. Since dst is going to be removed, it can no longer be
relied on for FIB dumps so save the route type as fib6_type.
fc_type is set in current users based on the algorithm in rt6_fill_node:
- rt6i_flags contains RTF_LOCAL: fc_type = RTN_LOCAL
- rt6i_flags contains RTF_ANYCAST: fc_type = RTN_ANYCAST
- else fc_type = RTN_UNICAST
Similarly, fib6_type is set in the rt6_info templates based on the
RTF_REJECT section of rt6_fill_node converting dst.error to RTN type.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:09 +0000 (17:33 -0700)]
vrf: Move fib6_table into net_vrf
A later patch removes rt6i_table from rt6_info. Save the ipv6
table for a VRF in net_vrf. fib tables can not be deleted so
no reference counting or locking is required.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:08 +0000 (17:33 -0700)]
net: Handle null dst in rtnl_put_cacheinfo
Need to keep expires time for IPv6 routes in a dump of FIB entries.
Update rtnl_put_cacheinfo to allow dst to be NULL in which case
rta_cacheinfo will only contain non-dst data.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 18 Apr 2018 00:33:07 +0000 (17:33 -0700)]
net: Move fib_convert_metrics to metrics file
Move logic of fib_convert_metrics into ip_metrics_convert. This allows
the code that converts netlink attributes into metrics struct to be
re-used in a later patch by IPv6.
This is mostly a code move with the following changes to variable names:
- fi->fib_net becomes net
- fc_mx and fc_mx_len are passed as inputs pulled from fib_config
- metrics array is passed as an input from fi->fib_metrics->metrics
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Tue, 17 Apr 2018 09:54:39 +0000 (11:54 +0200)]
ipv6: send netlink notifications for manually configured addresses
Send a netlink notification when userspace adds a manually configured
address if DAD is enabled and optimistic flag isn't set.
Moreover send RTM_DELADDR notifications for tentative addresses.
Some userspace applications (e.g. NetworkManager) are interested in
addr netlink events albeit the address is still in tentative state,
however events are not sent if DAD process is not completed.
If the address is added and immediately removed userspace listeners
are not notified. This behaviour can be easily reproduced by using
veth interfaces:
$ ip -b - <<EOF
> link add dev vm1 type veth peer name vm2
> link set dev vm1 up
> link set dev vm2 up
> addr add 2001:db8:a:b:1:2:3:4/64 dev vm1
> addr del 2001:db8:a:b:1:2:3:4/64 dev vm1
EOF
This patch reverts the behaviour introduced by the commit f784ad3d79e5
("ipv6: do not send RTM_DELADDR for tentative addresses")
Suggested-by: Thomas Haller <thaller@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 17 Apr 2018 06:11:28 +0000 (14:11 +0800)]
vxlan: add ttl inherit support
Like tos inherit, ttl inherit should also means inherit the inner protocol's
ttl values, which actually not implemented in vxlan yet.
But we could not treat ttl == 0 as "use the inner TTL", because that would be
used also when the "ttl" option is not specified and that would be a behavior
change, and breaking real use cases.
So add a different attribute IFLA_VXLAN_TTL_INHERIT when "ttl inherit" is
specified with ip cmd.
Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.
To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.
This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.
[ 114.926512] ==================================================================
[ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[ 114.947593]
[ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[ 115.170233] The buggy address belongs to the object at 94888540
[ 115.170233] which belongs to the cache kmalloc-32 of size 32
[ 115.181917] The buggy address is located 24 bytes inside of
[ 115.181917] 32-byte region [94888540, 94888560)
[ 115.192115] The buggy address belongs to the page:
[ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[ 115.204200] flags: 0x100(slab)
[ 115.207330] raw: 000001009488800094888fc10000003f000000019eea20149eecaa7496c003e0
[ 115.215444] page dumped because: kasan: bad access detected
[ 115.221036]
[ 115.222544] Memory state around the buggy address:
[ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.247077] ^
[ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.265639] ==================================================================
Reported-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Mon, 16 Apr 2018 21:29:22 +0000 (14:29 -0700)]
KEYS: DNS: limit the length of option strings
Adding a dns_resolver key whose payload contains a very long option name
resulted in that string being printed in full. This hit the WARN_ONCE()
in set_precision() during the printk(), because printk() only supports a
precision of up to 32767 bytes:
precision 1000000 too large
WARNING: CPU: 0 PID: 752 at lib/vsprintf.c:2189 vsnprintf+0x4bc/0x5b0
Fix it by limiting option strings (combined name + value) to a much more
reasonable 128 bytes. The exact limit is arbitrary, but currently the
only recognized option is formatted as "dnserror=%lu" which fits well
within this limit.
Also ratelimit the printks.
Reproducer:
perl -e 'print "#", "A" x 1000000, "\x00"' | keyctl padd dns_resolver desc @s
This bug was found using syzkaller.
Reported-by: Mark Rutland <mark.rutland@arm.com> Fixes: 4a2d789267e0 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 17 Apr 2018 17:00:39 +0000 (10:00 -0700)]
net/ipv6: Make __inet6_bind static
BPF core gets access to __inet6_bind via ipv6_bpf_stub_impl, so it is
not invoked directly outside of af_inet6.c. Make it static and move
inet6_bind after to avoid forward declaration.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Apr 2018 14:50:30 +0000 (10:50 -0400)]
Merge branch 'XDP-redirect-memory-return-API'
Jesper Dangaard Brouer says:
====================
XDP redirect memory return API
Submitted against net-next, as it contains NIC driver changes.
This patchset works towards supporting different XDP RX-ring memory
allocators. As this will be needed by the AF_XDP zero-copy mode.
The patchset uses mlx5 as the sample driver, which gets implemented
XDP_REDIRECT RX-mode, but not ndo_xdp_xmit (as this API is subject to
change thought the patchset).
A new struct xdp_frame is introduced (modeled after cpumap xdp_pkt).
And both ndo_xdp_xmit and the new xdp_return_frame end-up using this.
Support for a driver supplied allocator is implemented, and a
refurbished version of page_pool is the first return allocator type
introduced. This will be a integration point for AF_XDP zero-copy.
The mlx5 driver evolve into using the page_pool, and see a performance
increase (with ndo_xdp_xmit out ixgbe driver) from 6Mpps to 12Mpps.
The patchset stop at 16 patches (one over limit), but more API changes
are planned. Specifically extending ndo_xdp_xmit and xdp_return_frame
APIs to support bulking. As this will address some known limits.
V2: Updated according to Tariq's feedback
V3: Updated based on feedback from Jason Wang and Alex Duyck
V4: Updated based on feedback from Tariq and Jason
V5: Fix SPDX license, add Tariq's reviews, improve patch desc for perf test
V6: Updated based on feedback from Eric Dumazet and Alex Duyck
V7: Adapt to i40e that got XDP_REDIRECT support in-between
V8:
Updated based on feedback kbuild test robot, and adjust for mlx5 changes
page_pool only compiled into kernel when drivers Kconfig 'select' feature
V9:
Remove some inline statements, let compiler decide what to inline
Fix return value in virtio_net driver
Adjust for mlx5 changes in-between submissions
V10:
Minor adjust for mlx5 requested by Tariq
Resubmit against net-next
V11: avoid leaking info stored in frame data on page reuse
====================
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
xdp: avoid leaking info stored in frame data on page reuse
The bpf infrastructure and verifier goes to great length to avoid
bpf progs leaking kernel (pointer) info.
For queueing an xdp_buff via XDP_REDIRECT, xdp_frame info stores
kernel info (incl pointers) in top part of frame data (xdp->data_hard_start).
Checks are in place to assure enough headroom is available for this.
This info is not cleared, and if the frame is reused, then a
malicious user could use bpf_xdp_adjust_head helper to move
xdp->data into this area. Thus, making this area readable.
This is not super critical as XDP progs requires root or
CAP_SYS_ADMIN, which are privileged enough for such info. An
effort (is underway) towards moving networking bpf hooks to the
lesser privileged mode CAP_NET_ADMIN, where leaking such info
should be avoided. Thus, this patch to clear the info when
needed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xdp: transition into using xdp_frame for return API
Changing API xdp_return_frame() to take struct xdp_frame as argument,
seems like a natural choice. But there are some subtle performance
details here that needs extra care, which is a deliberate choice.
When de-referencing xdp_frame on a remote CPU during DMA-TX
completion, result in the cache-line is change to "Shared"
state. Later when the page is reused for RX, then this xdp_frame
cache-line is written, which change the state to "Modified".
This situation already happens (naturally) for, virtio_net, tun and
cpumap as the xdp_frame pointer is the queued object. In tun and
cpumap, the ptr_ring is used for efficiently transferring cache-lines
(with pointers) between CPUs. Thus, the only option is to
de-referencing xdp_frame.
It is only the ixgbe driver that had an optimization, in which it can
avoid doing the de-reference of xdp_frame. The driver already have
TX-ring queue, which (in case of remote DMA-TX completion) have to be
transferred between CPUs anyhow. In this data area, we stored a
struct xdp_mem_info and a data pointer, which allowed us to avoid
de-referencing xdp_frame.
To compensate for this, a prefetchw is used for telling the cache
coherency protocol about our access pattern. My benchmarks show that
this prefetchw is enough to compensate the ixgbe driver.
V7: Adjust for commit d9314c474d4f ("i40e: add support for XDP_REDIRECT")
V8: Adjust for commit bd658dda4237 ("net/mlx5e: Separate dma base address
and offset in dma_sync call")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch shows how it is possible to have both the driver local page
cache, which uses elevated refcnt for "catching"/avoiding SKB
put_page returns the page through the page allocator. And at the
same time, have pages getting returned to the page_pool from
ndp_xdp_xmit DMA completion.
The performance improvement for XDP_REDIRECT in this patch is really
good. Especially considering that (currently) the xdp_return_frame
API and page_pool_put_page() does per frame operations of both
rhashtable ID-lookup and locked return into (page_pool) ptr_ring.
(It is the plan to remove these per frame operation in a followup
patchset).
The benchmark performed was RX on mlx5 and XDP_REDIRECT out ixgbe,
with xdp_redirect_map (using devmap) . And the target/maximum
capability of ixgbe is 13Mpps (on this HW setup).
Before this patch for mlx5, XDP redirected frames were returned via
the page allocator. The single flow performance was 6Mpps, and if I
started two flows the collective performance drop to 4Mpps, because we
hit the page allocator lock (further negative scaling occurs).
Two test scenarios need to be covered, for xdp_return_frame API, which
is DMA-TX completion running on same-CPU or cross-CPU free/return.
Results were same-CPU=10Mpps, and cross-CPU=12Mpps. This is very
close to our 13Mpps max target.
The reason max target isn't reached in cross-CPU test, is likely due
to RX-ring DMA unmap/map overhead (which doesn't occur in ixgbe to
ixgbe testing). It is also planned to remove this unnecessary DMA
unmap in a later patchset
V2: Adjustments requested by Tariq
- Changed page_pool_create return codes not return NULL, only
ERR_PTR, as this simplifies err handling in drivers.
- Save a branch in mlx5e_page_release
- Correct page_pool size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
V5: Updated patch desc
V8: Adjust for b0cedc844c00 ("net/mlx5e: Remove rq_headroom field from params")
V9:
- Adjust for 121e89275471 ("net/mlx5e: Refactor RQ XDP_TX indication")
- Adjust for 73281b78a37a ("net/mlx5e: Derive Striding RQ size from MTU")
- Correct handling if page_pool_create fail for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
V10: Req from Tariq
- Change pool_size calc for MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xdp: allow page_pool as an allocator type in xdp_return_frame
New allocator type MEM_TYPE_PAGE_POOL for page_pool usage.
The registered allocator page_pool pointer is not available directly
from xdp_rxq_info, but it could be (if needed). For now, the driver
should keep separate track of the page_pool pointer, which it should
use for RX-ring page allocation.
As suggested by Saeed, to maintain a symmetric API it is the drivers
responsibility to allocate/create and free/destroy the page_pool.
Thus, after the driver have called xdp_rxq_info_unreg(), it is drivers
responsibility to free the page_pool, but with a RCU free call. This
is done easily via the page_pool helper page_pool_destroy() (which
avoids touching any driver code during the RCU callback, which could
happen after the driver have been unloaded).
V8: address issues found by kbuild test robot
- Address sparse should be static warnings
- Allow xdp.o to be compiled without page_pool.o
V9: Remove inline from .c file, compiler knows best
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log