Al Viro [Fri, 31 Oct 2008 23:28:30 +0000 (23:28 +0000)]
saner FASYNC handling on file close
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serge Hallyn [Thu, 30 Oct 2008 16:52:23 +0000 (11:52 -0500)]
file caps: always start with clear bprm->caps_*
While Linux doesn't honor setuid on scripts. However, it mistakenly
behaves differently for file capabilities.
This patch fixes that behavior by making sure that get_file_caps()
begins with empty bprm->caps_*. That way when a script is loaded,
its bprm->caps_* may be filled when binfmt_misc calls prepare_binprm(),
but they will be cleared again when binfmt_elf calls prepare_binprm()
next to read the interpreter's file capabilities.
Signed-off-by: Serge Hallyn <serue@us.ibm.com> Acked-by: David Howells <dhowells@redhat.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 31 Oct 2008 22:44:08 +0000 (15:44 -0700)]
Merge branch 'for-2.6.28' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
NLM: Set address family before calling nlm_host_rebooted()
nfsd: fix failure to set eof in readdir in some situations
Eric Paris [Fri, 31 Oct 2008 21:40:00 +0000 (17:40 -0400)]
SELinux: properly handle empty tty_files list
SELinux has wrongly (since 2004) had an incorrect test for an empty
tty->tty_files list. With an empty list selinux would be pointing to part
of the tty struct itself and would then proceed to dereference that value
and again dereference that result. An F10 change to plymouth on a ppc64
system is actually currently triggering this bug. This patch uses
list_empty() to handle empty lists rather than looking at a meaningless
location.
[note, this fixes the oops reported in
https://bugzilla.redhat.com/show_bug.cgi?id=469079]
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: James Morris <jmorris@namei.org>
Linus Torvalds [Fri, 31 Oct 2008 15:14:15 +0000 (08:14 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (21 commits)
sh: fix sh2a cache entry_mask
sh: Enable NFS root in Migo-R defconfig.
sh: FTRACE renamed to FUNCTION_TRACER.
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Define SCSPTR1 for SH 7751R
sh: Add sci_rxd_in of SH4-202
Add support usb setting on sh 7366
sh: Change register name SCSPTR to SCSPTR2
sh: use the new byteorder headers.
sh: SHmedia ISA tuning fixups.
sh: Kill off long-dead HD64465 cchip support.
sh: Revert "SH 7366 needs SCIF_ONLY"
sh: Simplify and lock down the ISA tuning.
sh: sh7785lcr: Select uImage as default image target.
sh: Add on-chip RTC support for SH7722.
SH 7366 needs SCIF_ONLY
gdrom: Fix compile error
sh: Provide a sample defconfig for the UL2 (SH7366) board.
sh: Fix FPU tuning on toolchains with mismatched multilib targets.
sh: oprofile: Fix up the SH7750 performance counter name.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add missing null terminating entry to bq4802_match[].
sparc: use the new byteorder headers
rtc-m48t59: shift zero year to 1968 on sparc (rev 2)
dbri: check dma_alloc_coherent errors
sparc64: remove byteshifting from out* helpers
Linus Torvalds [Fri, 31 Oct 2008 14:52:12 +0000 (07:52 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
delay capable() check in ext4_has_free_blocks()
merge ext4_claim_free_blocks & ext4_has_free_blocks
jbd2: Call the commit callback before the transaction could get dropped
ext4: fix a bug accessing freed memory in ext4_abort
ext3: fix a bug accessing freed memory in ext3_abort
Linus Torvalds [Fri, 31 Oct 2008 14:47:57 +0000 (07:47 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: add whitelist for devices with known good pata-sata bridges
sata_via: fix support for 5287
libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
ATA: remove excess kernel-doc notation
Paul Mackerras [Fri, 31 Oct 2008 10:34:09 +0000 (21:34 +1100)]
powerpc: Fix compile errors with CONFIG_BUG=n
This makes sure we don't try to call find_bug or is_warning_bug when
CONFIG_BUG=n and CONFIG_XMON=y. Otherwise we get these errors:
arch/powerpc/xmon/xmon.c: In function ‘print_bug_trap’:
arch/powerpc/xmon/xmon.c:1364: error: implicit declaration of function ‘find_bug’
arch/powerpc/xmon/xmon.c:1364: warning: assignment makes pointer from integer without a cast
arch/powerpc/xmon/xmon.c:1367: error: implicit declaration of function ‘is_warning_bug’
arch/powerpc/xmon/xmon.c:1374: error: dereferencing pointer to incomplete type
make[2]: *** [arch/powerpc/xmon/xmon.o] Error 1
make[1]: *** [arch/powerpc/xmon] Error 2
make: *** [sub-make] Error 2
Jon Smirl [Thu, 30 Oct 2008 16:51:32 +0000 (16:51 +0000)]
powerpc: Fix format string warning in arch/powerpc/boot/main.c
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 30 Oct 2008 16:37:05 +0000 (16:37 +0000)]
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450dcbfeb45ffc9d39b1747aee82b49a51 ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
sh: Fix up the shared IRQ demuxer's control bit testing logic.
Correct the interrupt handler in sh4 serial device, return the correct
value and check for what is anabled in the SCSCR register. The sh7722 is
broken just sending a break using minicom.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Matt Fleming [Wed, 29 Oct 2008 07:16:02 +0000 (07:16 +0000)]
Define SCSPTR1 for SH 7751R
After the recent commit to kill off SCI/SCIF special casing SH 7751R
fails to compile with CONFIG_SH_RTS7751R2D set. This is because SCSPTR1
is undefined. Take the value for SCSPTR1 from the SH7751R Group Hardware
Manual.
Signed-off-by: Matt Fleming <mjf@gentoo.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Harvey Harrison [Fri, 31 Oct 2008 07:01:22 +0000 (16:01 +0900)]
sh: use the new byteorder headers.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Jens Axboe [Wed, 27 Aug 2008 13:23:18 +0000 (15:23 +0200)]
libata: add whitelist for devices with known good pata-sata bridges
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Tejun Heo [Tue, 21 Oct 2008 15:46:36 +0000 (00:46 +0900)]
sata_via: fix support for 5287
5287 used to be treated as vt6420 but it didn't work. It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports. This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata. Another controller
which falls into this category is ata_piix w/ SIDPR access.
libata now has facility to deal with this class of controllers named
slave_link. A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.
This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.
This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.
Roland Dreier [Tue, 28 Oct 2008 23:52:20 +0000 (16:52 -0700)]
libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127
In ata_tf_to_lba48(), when evaluating
(tf->hob_lbal & 0xff) << 24
the expression is promoted to signed int (since int can hold all values
of u8). However, if hob_lbal is 128 or more, then it is treated as a
negative signed value and sign-extended when promoted to u64 to | into
sectors, which leads to the MSB 32 bits of section getting set
incorrectly.
For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported
that a 1.5GB drive caused:
Randy Dunlap [Thu, 30 Oct 2008 05:35:08 +0000 (22:35 -0700)]
ATA: remove excess kernel-doc notation
Remove excess kernel-doc function parameter notation from drivers/ata/:
Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task'
Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete'
Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Carl Love [Wed, 29 Oct 2008 05:06:45 +0000 (05:06 +0000)]
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
The size of the pm_signal_local array should be equal to the
number of SPUs being configured in the array. Currently, the
array is of size 4 (NR_PHYS_CTRS) but being indexed by a for
loop from 0 to 7 (NUM_SPUS_PER_NODE). This could potentially
cause an oops or random memory corruption since the pm_signal_local
array is on the stack. This fixes it.
Signed-off-by: Carl Love <carll@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Tue, 28 Oct 2008 18:01:39 +0000 (18:01 +0000)]
powerpc/mpic: Fix regression caused by change of default IRQ affinity
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 18404756765c713a0be4eb1082920c04822ce588 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark Nelson [Mon, 27 Oct 2008 20:38:08 +0000 (20:38 +0000)]
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
After the merge of the 32 and 64bit DMA code, dma_direct_ops lost
their map/unmap_single() functions but gained map/unmap_page(). This
caused a problem for Cell because Cell's dma_iommu_fixed_ops called
the dma_direct_ops if the fixed linear mapping was to be used or the
iommu ops if the dynamic window was to be used. So in order to fix
this problem we need to update the 64bit DMA code to use
map/unmap_page.
First, we update the generic IOMMU code so that iommu_map_single()
becomes iommu_map_page() and iommu_unmap_single() becomes
iommu_unmap_page(). Then we propagate these changes up through all
the callers of these two functions and in the process update all the
dma_mapping_ops so that they have map/unmap_page rahter than
map/unmap_single. We can do this because on 64bit there is no HIGHMEM
memory so map/unmap_page ends up performing exactly the same function
as map/unmap_single, just taking different arguments.
This has no affect on drivers because the dma_map_single_attrs() just
ends up calling the map_page() function of the appropriate
dma_mapping_ops and similarly the dma_unmap_single_attrs() calls
unmap_page().
This fixes an oops on Cell blades, which oops on boot without this
because they call dma_direct_ops.map_single, which is NULL.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
A typo/thinko made us pass the wrong argument to __flush_hash_table_range
when unplugging bridges, thus not flushing all the translations for
the IO space on unplug. The third parameter to __flush_hash_table_range
is `end', not `size'.
This causes the hypervisor to refuse unplugging slots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nathan Fontenot [Mon, 27 Oct 2008 19:48:17 +0000 (19:48 +0000)]
powerpc/pci: Properly allocate bus resources for hotplug PHBs
Resources for PHB's that are dynamically added to a system are not
properly allocated in the resource tree.
Not having these resources allocated causes an oops when removing
the PHB when we try to release them.
The diff appears a bit messy, this is mainly due to moving everything
one tab to the left in the pcibios_allocate_bus_resources routine.
The functionality change in this routine is only that the
list_for_each_entry() loop is pulled out and moved to the necessary
calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jeremy Kerr [Sun, 26 Oct 2008 21:51:25 +0000 (21:51 +0000)]
OF-device: Don't overwrite numa_node in device registration
Currently, the numa_node of OF-devices will be overwritten during
device_register, which simply sets the node to -1. On cell machines,
this means that devices can't find their IOMMU, which is referenced
through the device's numa node.
Set the numa node for OF devices with no parent, and use the
lower-level device_initialize and device_add functions, so that the
node is preserved.
We can remove the call to set_dev_node in of_device_alloc, as it
will be overwritten during register.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Thu, 23 Oct 2008 00:42:36 +0000 (00:42 +0000)]
powerpc: Fix swapcontext system for VSX + old ucontext size
Since VSX support was added, we now have two sizes of ucontext_t;
the older, smaller size without the extra VSX state, and the new
larger size with the extra VSX state. A program using the
sys_swapcontext system call and supplying smaller ucontext_t
structures will currently get an EINVAL error if the task has
used VSX (e.g. because of calling library code that uses VSX) and
the old_ctx argument is non-NULL (i.e. the program is asking for
its current context to be saved). Thus the program will start
getting EINVAL errors on calls that previously worked.
This commit changes this behaviour so that we don't send an EINVAL in
this case. It will now return the smaller context but the VSX MSR bit
will always be cleared to indicate that the ucontext_t doesn't include
the extra VSX state, even if the task has executed VSX instructions.
Both 32 and 64 bit cases are updated.
[paulus@samba.org - also fix some access_ok() and get_user() calls]
Thanks to Ben Herrenschmidt for noticing this problem.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Wed, 22 Oct 2008 18:43:45 +0000 (18:43 +0000)]
powerpc: Work around ld bug in older binutils
Commit 549e8152de8039506f69c677a4546e5427aa6ae7 ("powerpc: Make the
64-bit kernel as a position-independent executable") added lines to
vmlinux.lds.S to add the extra sections needed to implement a
relocatable kernel. However, those lines seem to trigger a bug in
older versions of GNU ld (such as 2.16.1) when building a
non-relocatable kernel. Since ld 2.16.1 is still a popular choice for
cross-toolchains, this adds an #ifdef to vmlinux.lds.S so the added
lines are only included when building a relocatable kernel.
Milton Miller [Thu, 23 Oct 2008 18:41:09 +0000 (18:41 +0000)]
powerpc/ppc64/kdump: Better flag for running relocatable
The __kdump_flag ABI is overly constraining for future development.
As of 2.6.27, the kernel entry point has 4 constraints: Offset 0 is
the starting point for the master (boot) cpu (entered with r3 pointing
to the device tree structure), offset 0x60 is code for the slave cpus
(entered with r3 set to their device tree physical id), offset 0x20 is
used by the iseries hypervisor, and secondary cpus must be well behaved
when the first 256 bytes are copied to address 0.
Placing the __kdump_flag at 0x18 is bad because:
- It was taking the last 8 bytes before the iseries hypervisor data.
- It was 8 bytes for a boolean flag
- It had no way of identifying that the flag was present
- It does leave any room for the master to add any additional code
before branching, which hurts debug.
- It will be unnecessarily hard for 32 bit code to be common (8 bytes)
Now that we have eliminated the use of __kdump_flag in favor of
the standard is_kdump_kernel(), this flag only controls run without
relocating the kernel to PHYSICAL_START (0), so rename it __run_at_load.
Move the flag to 0x5c, 1 word before the secondary cpu entry point at
0x60. Initialize it with "run0" to say it will run at 0 unless it is
set to 1. It only exists if we are relocatable.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Milton Miller [Wed, 22 Oct 2008 10:39:18 +0000 (10:39 +0000)]
powerpc: Kexec exit should not use magic numbers
Commit 54622f10a6aabb8bb2bdacf3dd070046f03dc246 ("powerpc: Support for
relocatable kdump kernel") added a magic flag value in a register to
tell purgatory that it should be a panic kernel. This part is wrong
and is reverted by this commit.
The kernel gets a list of memory blocks and a entry point from user space.
Its job is to copy the blocks into place and then branch to the designated
entry point (after turning "off" the mmu).
The user space tool inserts a trampoline, called purgatory, that runs
before the user supplied code. Its job is to establish the entry
environment for the new kernel or other application based on the contents
of memory. The purgatory code is compiled and embedded in the tool,
where it is later patched using the elf symbol table using elf symbols.
Since the tool knows it is creating a purgatory that will run after a
kernel crash, it should just patch purgatory (or the kernel directly)
if something needs to happen.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: fix irq vectors.
lguest: fix early_ioremap.
lguest: fix example launcher compile after moved asm-x86 dir.
Linus Torvalds [Fri, 31 Oct 2008 01:32:03 +0000 (18:32 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: remove sched-design.txt from 00-INDEX
sched: change sched_debug's mode to 0444
Linus Torvalds [Fri, 31 Oct 2008 01:31:42 +0000 (18:31 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: handle archs that do not support irqs_disabled_flags
Rusty Russell [Fri, 31 Oct 2008 16:24:27 +0000 (11:24 -0500)]
lguest: fix early_ioremap.
dmi_scan_machine breaks under lguest:
lguest: unhandled trap 14 at 0xc04edeae (0xffa00000)
This is because we use current_cr3 for the read_cr3() paravirt
function, and it isn't set until the first cr3 change. We got away
with it until this happened.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Ingo Molnar [Thu, 30 Oct 2008 23:43:03 +0000 (00:43 +0100)]
x86: cpu_index build fix
fix:
arch/x86/kernel/cpu/common.c: In function 'early_identify_cpu':
arch/x86/kernel/cpu/common.c:553: error: 'struct cpuinfo_x86' has no member named 'cpu_index'
James Bottomley [Thu, 30 Oct 2008 21:13:37 +0000 (16:13 -0500)]
x86/voyager: fix missing cpu_index initialisation
Impact: fix /proc/cpuinfo output on x86/Voyager
Ever since
| commit 92cb7612aee39642d109b8d935ad265e602c0563
| Author: Mike Travis <travis@sgi.com>
| Date: Fri Oct 19 20:35:04 2007 +0200
|
| x86: convert cpuinfo_x86 array to a per_cpu array
We've had an extra field in cpuinfo_x86 which is cpu_index.
Unfortunately, voyager has never initialised this, although the only
noticeable impact seems to be that /proc/cpuinfo shows all zeros for
the processor ids.
Anyway, fix this by initialising the boot CPU properly and setting the
index when the secondaries update.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
| Author: Suresh Siddha <suresh.b.siddha@intel.com>
| Date: Tue Jul 29 10:29:19 2008 -0700
|
| x86, xsave: enable xsave/xrstor on cpus with xsave support
Which deliberately expose boot cpu dependence to pieces of the system,
I think it's time to explicitly have a variable for it to prevent this
continual misassumption that the boot CPU is zero.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Steven Rostedt [Fri, 24 Oct 2008 13:42:59 +0000 (09:42 -0400)]
ftrace: handle archs that do not support irqs_disabled_flags
Impact: build fix on non-lockdep architectures
Some architectures do not support a way to read the irq flags that
is set from "local_irq_save(flags)" to determine if interrupts were
disabled or enabled. Ftrace uses this information to display to the user
if the trace occurred with interrupts enabled or disabled.
Besides the fact that those archs that do not support this will fail to
compile, unless they fix it, we do not want to have the trace simply
say interrupts were not disabled or they were enabled, without knowing
the real answer.
This patch adds a 'X' in the output to let the user know that the
architecture they are running on does not support a way for the tracer
to determine if interrupts were enabled or disabled. It also lets those
same archs compile with tracing enabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: fix /dev/mem mmap breakage when PAT is disabled
Impact: allow /dev/mem mmaps on non-PAT CPUs/platforms
Fix mmap to /dev/mem when CONFIG_X86_PAT is off and CONFIG_STRICT_DEVMEM is
off
mmap to /dev/mem on kernel memory has been failing since the
introduction of PAT (CONFIG_STRICT_DEVMEM=n case). Seems like
the check to avoid cache aliasing with PAT is kicking in even
when PAT is disabled. The bug seems to have crept in 2.6.26.
This patch makes sure that the mmap to regular
kernel memory succeeds if CONFIG_STRICT_DEVMEM=n and
PAT is disabled, and the checks to avoid cache aliasing
still happens if PAT is enabled.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org> Tested-by: Tim Sirianni <tim@scalemp.com> Cc: <stable@kernel.org> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
prefill_possible_mask() was hidden under CONFIG_HOTPLUG_CPU rendering
it invisitble to voyager. Since this commit it's exposed, but not
provided by the voyager subarch, so add a dummy stub to fix the link
breakage.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
James Bottomley [Thu, 30 Oct 2008 21:05:39 +0000 (16:05 -0500)]
x86: use CONFIG_X86_SMP instead of CONFIG_SMP
Impact: fix x86/Voyager boot
CONFIG_SMP is used for features which work on *all* x86 boxes.
CONFIG_X86_SMP is used for standard PC like x86 boxes (for things like
multi core and apics)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
James Bottomley [Thu, 30 Oct 2008 21:08:38 +0000 (16:08 -0500)]
x86/voyager: fix boot breakage caused by x86: boot secondary cpus through initial_code
Impact: boot up secondary CPUs as well on x86/Voyager systems
This commit:
| commit 3e9704739daf46a8ba6593d749c67b5f7cd633d2
| Author: Glauber Costa <gcosta@redhat.com>
| Date: Wed May 28 13:01:54 2008 -0300
|
| x86: boot secondary cpus through initial_code
removed the use of initialize_secondary. However, it didn't update
voyager, so the secondary cpus no longer boot. Fix this by adding the
initial_code switch to voyager as well.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chuck Lever [Thu, 23 Oct 2008 04:50:35 +0000 (00:50 -0400)]
NLM: Set address family before calling nlm_host_rebooted()
The nlm_host_rebooted() function uses nlm_cmp_addr() to find an
nsm_handle that matches the rebooted peer. In order for this to work,
the passed-in address must have a proper address family.
This fixes a post-2.6.28 regression introduced by commit 781b61a6, which
added AF_INET6 support to nlm_cmp_addr(). Before that commit,
nlm_cmp_addr() didn't care about the address family; it compared only
the sin_addr.s_addr field for equality.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
J. Bruce Fields [Thu, 30 Oct 2008 17:48:33 +0000 (13:48 -0400)]
nfsd: fix failure to set eof in readdir in some situations
Before 14f7dd632011bb89c035722edd6ea0d90ca6b078 "[PATCH] Copy XFS
readdir hack into nfsd code", readdir_cd->err was reset to eof before
each call to vfs_readdir; afterwards, it is set only once. Similarly, c002a6c7977320f95b5edede5ce4e0eeecf291ff "[PATCH] Optimise NFS readdir
hack slightly", can cause us to exit without nfserr_eof set. Fix this.
This ensures the "eof" bit is set when needed in readdir replies. (The
particular case I saw was an nfsv4 readdir of an empty directory, which
returned with no entries (the protocol requires "." and ".." to be
filtered out), but with eof unset.)
Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Fix incompatibility with versions of Perl less than 5.6.0
kbuild: do not include arch/<ARCH>/include/asm in find-sources twice.
kbuild: tag with git revision when git describe is missing
kbuild: prevent modpost from looking for a .cmd file for a static library linked into a module
kbuild: fix KBUILD_EXTRA_SYMBOLS
adjust init section definitions
scripts/checksyscalls.sh: fix for non-gnu sed
scripts/package: don't break if %{_smp_mflags} isn't set
kbuild: setlocalversion: dont include svn change count
kbuild: improve check-symlink
kbuild: mkspec - fix build rpm
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[PATCH] Switch all my contributions stuff to a single common address
[WATCHDOG] pci: use pci_ioremap_bar() in drivers/watchdog
Linus Torvalds [Thu, 30 Oct 2008 19:53:33 +0000 (12:53 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
CHAR: Delete old and now unused M48T35 RTC driver for SGI IP27.
CHAR: Delete old and now unused DS1286 driver.
MIPS: Sort out CPU type to name translation.
MIPS: Use the new byteorder headers
MIPS: Probe for watch registers on cores of all vendors, not just MTI.
MIPS: Switch FPU emulator trap to BREAK instruction.
MIPS: SMP: Do not initialize __cpu_number_map/__cpu_logical_map for CPU 0.
MIPS: Consider value of c0_ebase when computing value of exception base.
MIPS: Clean up MIPSxx-optimized bitop functions
MIPS: New feature test macro cpu_has_mips_r
MIPS: RBTX4927: Add GPIO-LED support
MIPS: TXx9: Fix RBTX4939 ethernet address initialization
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
fdomain_cs: Sort out modules with duplicate description
pcmcia: Whine harder about use of EXCLUSIVE
pcmcia: IRQ_TYPE_EXCLUSIVE is long obsoleted
Linus Torvalds [Thu, 30 Oct 2008 19:51:42 +0000 (12:51 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix potential race in put_rpccred()
SUNRPC: Fix rpcauth_prune_expired
NFS: Convert nfs_attr_generation_counter into an atomic_long
SUNRPC: Respond promptly to server TCP resets
Alan Cox [Thu, 30 Oct 2008 15:54:12 +0000 (15:54 +0000)]
tty: Fix USB kref leak
When we close we must clear the extra reference we got when we read
port->tty. Setting the port tty NULL will clear the kref held by the driver
but not the one we obtained ourselves while doing the lookup.
Linus Torvalds [Thu, 30 Oct 2008 19:07:25 +0000 (12:07 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Correct use of ! and &
i2c: The i2c mailing list is moving
scx200_i2c: Add missing class parameter
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: prevent autosuspend during hub initialization
USB: Unusual dev for the "Kyocera / Contax SL300R T*" digital camera.
USB: usbtmc: Use explicit unsigned type for input buffer instead of char*
USB: fix crash when URBs are unlinked after the device is gone
Linus Torvalds [Thu, 30 Oct 2008 18:44:35 +0000 (11:44 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix WM9713 ALC Decay Time name
ALSA: ASoC: Fix some minor errors in mpc5200 psc i2s driver
ALSA: ASoC: Fix mono controls after conversion to support full int masks
ALSA: sound/ice1712: indentation & braces disagree - add braces
ALSA: usb - Add quirk for Edirol UA-25EX advanced modes
sound: struct device - replace bus_id with dev_name(), dev_set_name()
ALSA: hda - Add reboot notifier
ALSA: Warn when control names are truncated
ALSA: intel8x0 - add Dell Optiplex GX620 (AD1981B) to AC97 clock whitelist
ALSA: hda - Fix SPDIF mute on IDT/STAC codecs
ALSA: hda: Add HDA vendor ID for Wolfson Microelectronics
ALSA: hda - Add another HP model for AD1884A
Linus Torvalds [Thu, 30 Oct 2008 18:44:09 +0000 (11:44 -0700)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: fix trace_nop config select
ftrace: perform an initialization for ftrace to enable it
LD drivers/spi/built-in.o
CC [M] drivers/spi/spi_gpio.o
In file included from drivers/spi/spi_gpio.c:26:
include/linux/spi/spi_bitbang.h:23: error: field `work' has incomplete type
make[2]: *** [drivers/spi/spi_gpio.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Wed, 29 Oct 2008 21:01:20 +0000 (14:01 -0700)]
nfsd: fix vm overcommit crash
Junjiro R. Okajima reported a problem where knfsd crashes if you are
using it to export shmemfs objects and run strict overcommit. In this
situation the current->mm based modifier to the overcommit goes through a
NULL pointer.
We could simply check for NULL and skip the modifier but we've caught
other real bugs in the past from mm being NULL here - cases where we did
need a valid mm set up (eg the exec bug about a year ago).
To preserve the checks and get the logic we want shuffle the checking
around and add a new helper to the vm_ security wrappers
Also fix a current->mm reference in nommu that should use the passed mm
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix build] Reported-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipmi: add MODULE_ALIAS to load ipmi_devintf with ipmi_si
The ipmi_devintf module contains the userspace interface for IPMI devices,
yet will not be loaded automatically with a system interface handler
driver.
Add a MODULE_ALIAS for the "platform:ipmi_si" MODALIAS exported by the
ipmi_si driver, so that userspace knows of the recommendation.
Signed-off-by: Scott James Remnant <scott@ubuntu.com> Cc: Tim Gardner <tcanonical@tpi.com> Cc: Corey Minyard <minyard@acm.org> Cc: <stable@kernel.org> [2.6.27.x, maybe earlier?] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Wed, 29 Oct 2008 21:01:17 +0000 (14:01 -0700)]
framebuffer compat_ioctl deadlock
Fix deadlock in fb_compat_ioctl. fb_compat_ioctl acquires a mutex and
calls fb_ioctl that tries to acquire that mutex too. A regression added
during BKL removal.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 29 Oct 2008 21:01:15 +0000 (14:01 -0700)]
kernel.h: fix might_sleep kernel-doc
Put the kernel-doc for might_sleep() _immediately_ before the macro
(no intervening lines). Otherwise kernel-doc complains like so:
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'file'
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'line'
because kernel-doc is looking at the wrong function prototype (i.e.,
__might_sleep). [Yes, I have a todo note to myself to check/warn for that
inconsistency in scripts/kernel-doc.]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: <Uwe.Kleine-Koenig@digi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'kill sig -1' must only apply to caller's namespace
Currently "kill <sig> -1" kills processes in all namespaces and breaks the
isolation of namespaces. Earlier attempt to fix this was discussed at:
http://lkml.org/lkml/2008/7/23/148
As suggested by Oleg Nesterov in that thread, use "task_pid_vnr() > 1"
check since task_pid_vnr() returns 0 if process is outside the caller's
namespace.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Tested-by: Daniel Hokka Zakrisson <daniel@hozac.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>