Linus Torvalds [Fri, 21 May 2010 14:20:17 +0000 (07:20 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
ocfs2: Silence a gcc warning.
ocfs2: Don't retry xattr set in case value extension fails.
ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
fs/ocfs2/dlm: Use kstrdup
fs/ocfs2/dlm: Drop memory allocation cast
Ocfs2: Optimize punching-hole code.
Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
ocfs2: Wrap signal blocking in void functions.
ocfs2/dlm: Increase o2dlm lockres hash size
ocfs2: Make ocfs2_extend_trans() really extend.
ocfs2/trivial: Code cleanup for allocation reservation.
ocfs2: make ocfs2_adjust_resv_from_alloc simple.
ocfs2: Make nointr a default mount option
ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
o2net: log socket state changes
ocfs2: print node # when tcp fails
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Linus Torvalds [Thu, 20 May 2010 20:34:17 +0000 (13:34 -0700)]
Merge branch 'viafb-next' of git://git.lwn.net/linux-2.6
* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
viafb: move some include files to include/linux
viafb: Eliminate some global.h references
viafb: get rid of i2c debug cruft
viafb: fold via_io.h into via-core.h
viafb: Fix initialization error paths
viafb: Do not remove gpiochip under spinlock
viafb: make procfs entries optional
viafb: fix proc entry removal
viafb: improve misc register handling
viafb: replace inb/outb
viafb: move some modesetting functions to a seperate file
viafb: unify modesetting functions
viafb: Reserve framebuffer memory for the upcoming camera driver
viafb: Add a simple VX855 DMA engine driver
viafb: Add a simple interrupt management infrastructure
via: Rationalize vt1636 detection
viafb: Introduce viafb_find_i2c_adapter()
via: Do not attempt I/O on inactive I2C adapters
viafb: Turn GPIO and i2c into proper platform devices
viafb: Convert GPIO and i2c to the new indexed port ops
...
Felipe Contreras [Sun, 16 May 2010 20:31:07 +0000 (23:31 +0300)]
usb-storage: always print quirks
Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.
So let's do the smart thing and print the quirks when they are present.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sun, 16 May 2010 13:06:55 +0000 (15:06 +0200)]
USB: visor: increase bulk-out buffer size
Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).
256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 15 May 2010 15:53:49 +0000 (17:53 +0200)]
USB: visor: reimplement using generic framework
Kill custom read and write implementations (dynamically allocated write
urbs).
Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c708ee2a9af14fbe235e0a41216f4ed
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nils Radtke [Mon, 17 May 2010 12:14:11 +0000 (14:14 +0200)]
USB: option.c: OLIVETTI OLICARD100 support
This patch adds support for an olivetti olicard100 HĐ DPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Ming Lei [Mon, 17 May 2010 14:20:50 +0000 (22:20 +0800)]
USB: remove match_device
usb_find_device was the only one user of match_device, now
it is removed, so remove match_device to fix the compile warning
below reported by Stephen Rothwell:
drivers/usb/core/usb.c:596: warning: 'match_device'
defined but not used
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anton Vorontsov [Fri, 14 May 2010 14:33:18 +0000 (18:33 +0400)]
USB: FHCI: cq_get() should check kfifo_out()'s return value
Since commit 7acd72eb85f1c7a15e8b5eb554994949241737f1 ("kfifo: rename
kfifo_put... into kfifo_in... and kfifo_get... into kfifo_out..."),
kfifo_out() is marked __must_check, and that causes gcc to produce
lots of warnings like this:
CC drivers/usb/host/fhci-mem.o
In file included from drivers/usb/host/fhci-hcd.c:34:
drivers/usb/host/fhci.h: In function 'cq_get':
drivers/usb/host/fhci.h:520: warning: ignoring return value of 'kfifo_out', declared with attribute warn_unused_result
...
This patch fixes the issue by properly checking the return value.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Cc: stable <stable@kernel.org> [.33 and .34] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Thu, 13 May 2010 19:02:01 +0000 (21:02 +0200)]
USB: ir-usb: allow custom bulk buffer size without reallocation
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure
buffers of appropriate sizes are allocated in the first place rather than
reallocating them at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 12 May 2010 22:21:35 +0000 (18:21 -0400)]
USB: EHCI: fix controller wakeup flag settings during suspend
This patch (as1380) fixes a bug in the wakeup settings for EHCI host
controllers. When the controller is suspended, if it isn't enabled
for remote wakeup then we have to turn off all the port wakeup flags.
Disabling PCI PME# isn't good enough, because some systems (Intel)
evidently use alternate wakeup signalling paths.
In addition, the patch improves the handling of the Intel Moorestown
hardware by performing various power-up and power-down delays just
once instead of once for each port (i.e., the delays are moved outside
of the port loops). This requires extra code, but the total delay
time is reduced.
There are also a few additional minor cleanups.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Ondrej Zary <linux@rainbow-software.org> CC: Alek Du <alek.du@intel.com> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alek Du [Mon, 10 May 2010 03:17:49 +0000 (11:17 +0800)]
USB: EHCI: clear PHCD before resuming
This is a bug fix for PHCD (phy clock disable) low power feature:
After PHCD is set, any write to PORTSC register is illegal, so when
resume ports, clear PHCD bit first.
Signed-off-by: Alek Du <alek.du@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/media/dvb/dvb-usb/dvb-usb-init.c:230: if ((desc =
dvb_usb_find_device(udev,props,&cold)) == NULL) {
drivers/usb/core/usb.c:630: * usb_find_device - find a specific usb device in the system
drivers/usb/core/usb.c:642:struct usb_device *usb_find_device(u16 vendor_id, u16 product_id)
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: gadget: f_mass_storage: fix in error recovery
In to places in fsg_common_init() an unconditional call to kfree()
on common was performed in error recovery which is not a valid
behaviour since fsg_common structure is not always allocated by
fsg_common_init().
To fix, the calls has been replaced with a goto to a proper error
recovery which does the correct thing.
Ming Lei [Wed, 12 May 2010 15:38:12 +0000 (23:38 +0800)]
USB: add missing "{}" in map_urb_for_dma
Obviously, {} is needed in the branch of
"else if (hcd->driver->flags & HCD_LOCAL_MEM)"
for handling of setup packet mapping.
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anand Gadiyar [Thu, 6 May 2010 14:39:48 +0000 (20:09 +0530)]
USB: ehci-omap: Fix resume failures after bus suspend
An undocumented "feature" in the OMAP3 EHCI controller causes
suspended ports to be taken out of suspend when the USBCMD.Run/Stop
bit is cleared (this bit is normally cleared when ehci_bus_suspend
is called).
This "feature" breaks suspend-resume if the root-hub is allowed
to suspend. (The controller thinks it is in resume, and the PHY
thinks it is still in suspend).
There is an undocumented register bit that can be used to disable
this feature and restore normal behavior. Set this bit so
suspend-resume can work normally.
Tested on OMAP3 SDPs with the NXP ISP1504 and NXP ISP1703 PHYs.
Alan Stern [Tue, 11 May 2010 15:44:06 +0000 (11:44 -0400)]
USB: fix interface runtime-PM settings
This patch (as1379) reworks the logic for handling USB interface
runtime-PM settings -- hopefully it's right this time! The problem is
that when a driver is unbound or binding fails, runtime PM for the
interface always gets disabled. But pm_runtime_disable() nests, so it
shouldn't be called unless the interface was previously enabled for
runtime PM.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Rob Duncan <Robert.Duncan@exar.com> Tested-by: Rob Duncan <Robert.Duncan@exar.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
John Youn [Mon, 10 May 2010 22:33:00 +0000 (15:33 -0700)]
USB: xhci: Transfer ring link TRB activation change.
Change transfer ring behavior to not follow/activate link TRBs
until active TRBs are queued after it. This change affects
the behavior when a TD ends just before a link TRB.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Mon, 10 May 2010 17:51:36 +0000 (10:51 -0700)]
USB: gadget: f_fs.c needs to include pagemap.h
Fix g_ffs build error, add a needed header file:
drivers/usb/gadget/f_fs.c:1064:error: 'PAGE_CACHE_SIZE' undeclared (first use in this function)
drivers/usb/gadget/f_fs.c:1065:error: 'PAGE_CACHE_SHIFT' undeclared (first use in this function)
Anand Gadiyar [Mon, 10 May 2010 16:26:12 +0000 (21:56 +0530)]
USB: ohci: Add Kconfig entries for ohci-omap3
On OMAP systems, we have two different OHCI controllers. The legacy
one is present in OMAP1/2 chips, and the newer one comes bundled as
a companion to the EHCI controller on OMAP3 and newer chips.
We may have multi-omap configurations where OMAP2 and OMAP3
support may be enabled in the same kernel, and need a mechanism
to keep both drivers around.
This patch adds a Kconfig entry for each of these drivers.
Anand Gadiyar [Mon, 10 May 2010 16:26:11 +0000 (21:56 +0530)]
USB: ohci: introduce omap3 ohci-hcd driver
Add support for the OHCI controller present in OMAP3 and newer chips.
The code is mostly based off the ehci-omap.c driver.
Some of it is common to both drivers and will eventually
need to be factored out to platform init files.
In its current state, the driver cannot co-exist with the ehci-omap
driver, and this will be fixed in later versions. The second driver
to be loaded will overwrite settings made by the other. For now,
this driver should allow the few users of OMAP3 OHCI to get going.
Johan Hovold [Sat, 8 May 2010 13:19:24 +0000 (15:19 +0200)]
USB: ftdi_sio: clean up line-status handling
Reverse priority of errors reported to ldisc so that it matches that of
other serial drivers (break takes precedence over parity, which takes
precedence over framing errors).
Also make sure overrun errors are handled as in other drivers, that is,
an overrun error is always reported and is not associated with any
received character (instead a NULL character with the TTY_OVERRUN flag
set is inserted).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Anton Vorontsov [Thu, 6 May 2010 21:09:19 +0000 (01:09 +0400)]
USB: isp1760: Soften DW3 X/transaction error bit handling
There were some reports[1] of isp1760 USB driver malfunctioning
with high speed devices, noticed on Blackfin and PowerPC targets.
These reports indicated that the original Philips 'pehcd'[2]
driver worked fine.
We've noticed the same issue with an ARM RealView platform. This
happens under load (with only some mass storage devices, not all,
just as in another report[3]):
error bit is set in DW3
error bit is set in DW3
error bit is set in DW3
usb 1-1.2: device descriptor read/64, error -32
It appears that the 'pehcd' driver checks the X bit only if the
transaction is halted (H bit), otherwise the error is so far
insignificant.
The ISP176x chips were modeled after EHCI, and EHCI spec says
(thanks to Alan Stern for pointing out):
"Transaction errors cause the status field to be updated to reflect
the type of error, but the transaction continues to be retried until
the Active bit is set to 0. When the error counter reaches 0, the
Halt bit is set and the Active bit is cleared."
So, just as the original Philips driver, isp1760 must report the
error only if the transaction error and the halt bits are set.
[1] http://markmail.org/message/lx4qrlbrs2uhcnly
[2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494
See pehci.c:pehci_hcd_update_error_status().
[3] http://blackfin.uclinux.org/gf/tracker/5148
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Fri, 7 May 2010 10:09:27 +0000 (18:09 +0800)]
USB: usbcore: Do not disable USB3 protocol ports in hub_activate()
When USB3 protocol port detects an USB3.0 device attach, the port will
automatically transition to the Enabled state upon the completion
of successful link training.
Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device
will fail to be recognized if xHCI bus power management is implemented.
Johan Hovold [Fri, 7 May 2010 17:46:56 +0000 (19:46 +0200)]
USB: tty: fix incorrect use of tty_insert_flip_string_fixed_flag
Fix regression introduced by commit a108bfcb372d8c4452701039308fb95747911c59 (USB: tty: Prune uses of
tty_request_room in the USB layer) which broke three drivers
(cypress_m8, digi_acceleport and spcp8x5) through incorrect use of
tty_insert_flip_string_fixed_flag.
Robert Lukassen [Fri, 7 May 2010 07:19:53 +0000 (09:19 +0200)]
USB: gadget: Allow function access to device ID data during bind()
This is a patch that makes sure that the device ID data (idVendor,
idProduct and bcdDevice) are assigned to the descriptor in the cdev
structure *before* the composite gadget starts binding. This allows the
composite driver, and all the composite functions it uses, access to
that data.
In one of the composite functions we created, we needed to register an
input device and wanted to use the idVendor, idProduct and bcdDevice
codes to properly initialize the id field of the input device. We could
not do that because the idVendor, idProduct and bcdDevice values were
only set in the cdec structure *after* the composite->bind(cdev) call.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: testusb: testusb compatibility with FunctionFS gadget
The FunctionFS gadget may provide the source/sink interface
not as the first interface (with id == 0) but some different
interface hence a code to find the interface number is
required.
(Note that you will still configure the gadget to report
idProduct == 0xa4a4 (an "echo 0xa4a4
>/sys/module/g_ffs/parameters/usb_product" should suffice) or
configure host to handle 0x0525:0xa4ac devices using the
usbtest driver.)
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 5 May 2010 10:53:17 +0000 (12:53 +0200)]
USB: testusb: an USB testing application
The testusb program just issues ioctls to perform the tests
implemented by the kernel driver. It can generate a variety
of transfer patterns; you should make sure to test both regular
streaming and mixes of transfer sizes (including short transfers).
For more information on how this can be used and on USB testing
refer to <URL:http://www.linux-usb.org/usbtest/>.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Function Filesystem (FunctioFS) lets one create USB
composite functions in user space in the same way as GadgetFS
lets one create USB gadgets in user space. This allows
creation of composite gadgets such that some of the functions
are implemented in kernel space (for instance Ethernet, serial
or mass storage) and other are implemented in user space.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The FunctionFS is a USB composite function that can be used
with the composite framework to create an USB gadget.
>From kernel point of view it is just a composite function with
some unique behaviour. It may be added to an USB
configuration only after the user space driver has registered
by writing descriptors and strings (the user space program has
to provide the same information that kernel level composite
functions provide when they are added to the configuration).
>From user space point of view it is a file system which when
mounted provide an "ep0" file. User space driver need to
write descriptors and strings to that file. It does not need
to worry about endpoints, interfaces or strings numbers but
simply provide descriptors such as if the function was the
only one (endpoints and strings numbers starting from one and
interface numbers starting from core). The FunctionFS changes
numbers of those as needed also handling situation when
numbers differ in different configurations.
When descriptors and strings are written "ep#" files appear
(one for each declared endpoint) which handle communication on
a single endpoint. Again, FunctionFS takes care of the real
numbers and changing of the configuration (which means that
"ep1" file may be really mapped to (say) endpoint 3 (and when
configuration changes to (say) endpoint 2)). "ep0" is used
for receiving events and handling setup requests.
When all files are closed the function disables itself.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__init, __initdata and __exit tags have have been removed from
various files to make it possible for gadgets that do not use
the __init/__exit tags to use those.
Files in question are related to:
* the core composite framework,
* the mass storage function (fixing a section mismatch) and
* ethernet driver (ACM, ECM, RNDIS).
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fs/timerfd.c: make use of wait_event_interruptible_locked_irq()
This patch modifies the fs/timerfd.c to use the newly created
wait_event_interruptible_locked_irq() macro. This replaces an open
code implementation with a single macro call.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Roland Dreier <rolandd@cisco.com> Cc: Tejun Heo <tj@kernel.org> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New wait_event_interruptible{,_exclusive}_locked{,_irq} macros added.
They work just like versions without _locked* suffix but require the
wait queue's lock to be held. Also __wake_up_locked() is now exported
as to pair it with the above macros.
The use case of this new facility is when one uses wait queue's lock
to protect a data structure. This may be advantageous if the
structure needs to be protected by a spinlock anyway. In particular,
with additional spinlock the following code has to be used to wait
for a condition:
spin_lock(&data.lock);
...
for (ret = 0; !ret && !(condition); ) {
spin_unlock(&data.lock);
ret = wait_event_interruptible(data.wqh, (condition));
spin_lock(&data.lock);
}
...
spin_unlock(&data.lock);
This looks bizarre plus wait_event_interruptible() locks the wait
queue's lock anyway so there is a unlock+lock sequence where it could
be avoided.
To avoid those problems and benefit from wait queue's lock, a code
similar to the following should be used:
projects / mirror_ubuntu-kernels.git / log