When using SCSI passthrough in combination with the iSCSI target driver
then cmd->t_state_lock may be obtained from interrupt context. Hence, all
code that obtains cmd->t_state_lock from thread context must disable
interrupts first. This patch avoids that lockdep reports the following:
WARNING: inconsistent lock state
4.18.0-dbg+ #1 Not tainted
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
iscsi_ttx/1800 [HC1[1]:SC0[2]:HE0:SE0] takes: 000000006e7b0ceb (&(&cmd->t_state_lock)->rlock){?...}, at: target_complete_cmd+0x47/0x2c0 [target_core_mod]
{HARDIRQ-ON-W} state was registered at:
lock_acquire+0xd2/0x260
_raw_spin_lock+0x32/0x50
iscsit_close_connection+0x97e/0x1020 [iscsi_target_mod]
iscsit_take_action_for_connection_exit+0x108/0x200 [iscsi_target_mod]
iscsi_target_rx_thread+0x180/0x190 [iscsi_target_mod]
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
irq event stamp: 1281
hardirqs last enabled at (1279): [<ffffffff970ade79>] __local_bh_enable_ip+0xa9/0x160
hardirqs last disabled at (1281): [<ffffffff97a008a5>] interrupt_entry+0xb5/0xd0
softirqs last enabled at (1278): [<ffffffff977cd9a1>] lock_sock_nested+0x51/0xc0
softirqs last disabled at (1280): [<ffffffffc07a6e04>] ip6_finish_output2+0x124/0xe40 [ipv6]
other info that might help us debug this:
Possible unsafe locking scenario:
It was reported that some devices report an OPTIMAL TRANSFER LENGTH of
0xFFFF blocks. That looks bogus, especially for a device with a
4096-byte physical block size.
Ignore OPTIMAL TRANSFER LENGTH if it is not a multiple of the device's
reported physical block size.
To make the sanity checking conditionals more readable--and to
facilitate printing warnings--relocate the checking to a helper
function. No functional change aside from the printks.
Cc: <stable@vger.kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199759 Reported-by: Christoph Anton Mitterer <calestyo@scientia.net> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The virtio scsi spec defines struct virtio_scsi_ctrl_tmf as a set of
device-readable records and a single device-writable response entry:
struct virtio_scsi_ctrl_tmf
{
// Device-readable part
le32 type;
le32 subtype;
u8 lun[8];
le64 id;
// Device-writable part
u8 response;
}
The above should be organised as two descriptor entries (or potentially
more if using VIRTIO_F_ANY_LAYOUT), but without any extra data after "le64
id" or after "u8 response".
The Linux driver doesn't respect that, with virtscsi_abort() and
virtscsi_device_reset() setting cmd->sc before calling virtscsi_tmf(). It
results in the original scsi command payload (or writable buffers) added to
the tmf.
This fixes the problem by leaving cmd->sc zeroed out, which makes
virtscsi_kick_cmd() add the tmf to the control vq without any payload.
Cc: stable@vger.kernel.org Signed-off-by: Felipe Franciosi <felipe@nutanix.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
A queue with a capacity of zero is clearly not a valid virtio queue.
Some emulators report zero queue size if queried with an invalid queue
index. Instead of crashing in this case let us just return -ENOENT. To
make that work properly, let us fix the notifier cleanup logic as well.
Cc: stable@vger.kernel.org Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The setup_lowcore() function creates a new prefix page for the boot CPU.
The PSW mask for the system_call, external interrupt, i/o interrupt and
the program check handler have the DAT bit set in this new prefix page.
At the time setup_lowcore is called the system still runs without virtual
address translation, the paging_init() function creates the kernel page
table and loads the CR13 with the kernel ASCE.
Any code between setup_lowcore() and the end of paging_init() that has
a BUG or WARN statement will create a program check that can not be
handled correctly as there is no kernel page table yet.
To allow early WARN statements initially setup the lowcore with DAT off
and set the DAT bit only after paging_init() has completed.
Libudev relies on having a subsystem link for non-root devices. To
avoid libudev (and potentially other userspace tools) choking on the
matrix device let us introduce a matrix bus and with it the matrix
bus subsytem. Also make the matrix device reside within the matrix
bus.
Doing this we remove the forced link from the matrix device to the
vfio_ap driver and the device_type we do not need anymore.
Since the associated matrix driver is not the vfio_ap driver any more,
we have to change the search for the devices on the vfio_ap driver in
the function vfio_ap_verify_queue_reserved. Fixes: 1fde573413b5 ("s390: vfio-ap: base implementation of VFIO AP device driver") Cc: stable@vger.kernel.org Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Pierre Morel <pmorel@linux.ibm.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com> Acked-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The Allwinner A64 SoC is known[1] to have an unstable architectural
timer, which manifests itself most obviously in the time jumping forward
a multiple of 95 years[2][3]. This coincides with 2^56 cycles at a
timer frequency of 24 MHz, implying that the time went slightly backward
(and this was interpreted by the kernel as it jumping forward and
wrapping around past the epoch).
Investigation revealed instability in the low bits of CNTVCT at the
point a high bit rolls over. This leads to power-of-two cycle forward
and backward jumps. (Testing shows that forward jumps are about twice as
likely as backward jumps.) Since the counter value returns to normal
after an indeterminate read, each "jump" really consists of both a
forward and backward jump from the software perspective.
Unless the kernel is trapping CNTVCT reads, a userspace program is able
to read the register in a loop faster than it changes. A test program
running on all 4 CPU cores that reported jumps larger than 100 ms was
run for 13.6 hours and reported the following:
This works out to a jump larger than 100 ms about every 5.5 seconds on
each CPU core.
The largest jump (almost an hour!) was the following sequence of reads:
0x0000007fffffffff → 0x00000093feffffff → 0x0000008000000000
Note that the middle bits don't necessarily all read as all zeroes or
all ones during the anomalous behavior; however the low 10 bits checked
by the function in this patch have never been observed with any other
value.
Also note that smaller jumps are much more common, with backward jumps
of 2048 (2^11) cycles observed over 400 times per second on each core.
(Of course, this is partially explained by lower bits rolling over more
frequently.) Any one of these could have caused the 95 year time skip.
Similar anomalies were observed while reading CNTPCT (after patching the
kernel to allow reads from userspace). However, the CNTPCT jumps are
much less frequent, and only small jumps were observed. The same program
as before (except now reading CNTPCT) observed after 72 hours:
Further investigation showed that the instability in CNTPCT/CNTVCT also
affected the respective timer's TVAL register. The following values were
observed immediately after writing CNVT_TVAL to 0x10000000:
I was also twice able to reproduce the issue covered by Allwinner's
workaround[4], that writing to TVAL sometimes fails, and both CVAL and
TVAL are left with entirely bogus values. One was the following values:
CNTVCT | CNTV_TVAL | CNTV_CVAL
--------------------+------------+--------------------------------------
0x000000d4a2d6014c | 0x8fbd5721 | 0x000000d132935fff (615s in the past) Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
========================================================================
Because the CPU can read the CNTPCT/CNTVCT registers faster than they
change, performing two reads of the register and comparing the high bits
(like other workarounds) is not a workable solution. And because the
timer can jump both forward and backward, no pair of reads can
distinguish a good value from a bad one. The only way to guarantee a
good value from consecutive reads would be to read _three_ times, and
take the middle value only if the three values are 1) each unique and
2) increasing. This takes at minimum 3 counter cycles (125 ns), or more
if an anomaly is detected.
However, since there is a distinct pattern to the bad values, we can
optimize the common case (1022/1024 of the time) to a single read by
simply ignoring values that match the error pattern. This still takes no
more than 3 cycles in the worst case, and requires much less code. As an
additional safety check, we still limit the loop iteration to the number
of max-frequency (1.2 GHz) CPU cycles in three 24 MHz counter periods.
For the TVAL registers, the simple solution is to not use them. Instead,
read or write the CVAL and calculate the TVAL value in software.
Although the manufacturer is aware of at least part of the erratum[4],
there is no official name for it. For now, use the kernel-internal name
"UNKNOWN1".
When shutting down the timer, ensure that after we have stopped the
timer any pending interrupts are cleared. This fixes a problem when
suspending, as interrupts are disabled before the timer is stopped,
so the timer interrupt may still be asserted, preventing the system
entering a low power state when the wfi is executed.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Cc: <stable@vger.kernel.org> # v4.3+ Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When a timer tick occurs and the clock is in one-shot mode, the timer
needs to be stopped to prevent it triggering subsequent interrupts.
Currently this code is in exynos4_mct_tick_clear(), but as it is
only needed when an ISR occurs move it into exynos4_mct_tick_isr(),
leaving exynos4_mct_tick_clear() just doing what its name suggests it
should.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Cc: stable@vger.kernel.org # v4.3+ Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The step values for some of the LDOs appears to be incorrect, resulting
in incorrect voltages (or at least, ones which are different from the
Samsung 3.4 vendor kernel).
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If regulator DT node doesn't exist, its of_parse_cb callback
function isn't called. Then all values for DT properties are
filled with zero. This leads to wrong register update for
FPS and POK settings.
Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com> Signed-off-by: Mark Zhang <markz@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org> Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
spi-gpio is capable of dealing with active-high chip-selects.
Unfortunately, commit 4b859db2c606 ("spi: spi-gpio: add SPI_3WIRE
support") broke this by setting master->mode_bits, which overrides
the setting in the spi-bitbang code. Fix this.
[Fixed a trivial conflict with SPI_3WIRE_HIZ support -- broonie]
Fixes: 4b859db2c606 ("spi: spi-gpio: add SPI_3WIRE support") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length")
broke SPI transfers where bits_per_word != 8. This is because of
mimsatch between McSPI FIFO level event trigger size (SPI word length) and
DMA request size(word length * maxburst). This leads to data
corruption, lockup and errors like:
spi1.0: EOW timed out
Fix this by setting DMA maxburst size to 1 so that
McSPI FIFO level event trigger size matches DMA request size.
Fixes: b682cffa3ac6 ("spi: omap2-mcspi: Set FIFO DMA trigger level to word length") Cc: stable@vger.kernel.org Reported-by: David Lechner <david@lechnology.com> Tested-by: David Lechner <david@lechnology.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
("spi: pxa2xx: Switch to SPI core DMA mapping functionality")
switches to SPI core provided DMA helpers, it missed to setup maximum
supported DMA transfer length for the controller and thus users
mistakenly try to send more data than supported with the following
warning:
ili9341 spi-PRP0001:01: DMA disabled for transfer length 153600 greater than 65536
Setup maximum supported DMA transfer length in order to make users know
the limit.
Fixes: b6ced294fb61 ("spi: pxa2xx: Switch to SPI core DMA mapping functionality") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 4dea6c9b0b64 ("spi: spi-ti-qspi: add mmap mode read support") has
has got order of parameter wrong when calling regmap_update_bits() to
select CS for mmap access. Mask and value arguments are interchanged.
Code will work on a system with single slave, but fails when more than
one CS is in use. Fix this by correcting the order of parameters when
calling regmap_update_bits().
Fixes: 4dea6c9b0b64 ("spi: spi-ti-qspi: add mmap mode read support") Cc: stable@vger.kernel.org Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The original purpose of the code I fix is to replace max_discard with
max_trim if max_trim is less than max_discard. When max_discard is 0
we should replace max_discard with max_trim as well, because
max_discard equals 0 happens only when the max_do_calc_max_discard
process is overflowed, so if mmc_can_trim(card) is true, max_discard
should be replaced by an available max_trim.
However, in the original code, there are two lines of code interfere
the right process.
1) if (max_discard && mmc_can_trim(card))
when max_discard is 0, it skips the process checking if max_discard
needs to be replaced with max_trim.
2) if (max_trim < max_discard)
the condition is false when max_discard is 0. it also skips the process
that replaces max_discard with max_trim, in fact, we should replace the
0-valued max_discard with max_trim.
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.
Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.12+ Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: d9370424c948 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If SSDT overlay is loaded via ConfigFS and then unloaded the device,
we would like to have OF modalias for, already gone. Thus, acpi_get_name()
returns no allocated buffer for such case and kernel crashes afterwards:
Commit f7c90c2aa40048 ("x86/xen: don't write ptes directly in 32-bit
PV guests") introduced a regression for booting dom0 on huge systems
with lots of RAM (in the TB range).
Reason is that on those hosts the p2m list needs to be moved early in
the boot process and this requires temporary page tables to be created.
Said commit modified xen_set_pte_init() to use a hypercall for writing
a PTE, but this requires the page table being in the direct mapped
area, which is not the case for the temporary page tables used in
xen_relocate_p2m().
As the page tables are completely written before being linked to the
actual address space instead of set_pte() a plain write to memory can
be used in xen_relocate_p2m().
The first version of this method was missing the check for
`ret == PATH_MAX`; then such a check was added, but it didn't call kfree()
on error, so there was still a small memory leak in the error case.
Fix it by using strndup_user() instead of open-coding it.
Commit d716ff71dd12 ("tracing: Remove taking of trace_types_lock in
pipe files") use the current tracer instead of the copy in
tracing_open_pipe(), but it forget to remove the freeing sentence in
the error path.
There's an error path that can call kfree(iter->trace) after the iter->trace
was assigned to tr->current_trace, which would be bad to free.
Because there may be random garbage beyond a string's null terminator,
it's not correct to copy the the complete character array for use as a
hist trigger key. This results in multiple histogram entries for the
'same' string key.
So, in the case of a string key, use strncpy instead of memcpy to
avoid copying in the extra bytes.
Before, using the gdbus entries in the following hist trigger as an
example:
We negotiate rsize mounts (and it can be overridden by user) to
typically 4MB, so using larger default I/O sizes from userspace
(changing to 1MB default i/o size returned by stat) the
performance is much better (and not just for long latency
network connections) in most use cases for SMB3 than the default I/O
size (which ends up being 128K for cp and can be even smaller for cp).
This can be 4x slower or worse depending on network latency.
By changing inode->blocksize from 32K (which was perhaps ok
for very old SMB1/CIFS) to a larger value, 1MB (but still less than
max size negotiated with the server which is 4MB, in order to minimize
risk) it significantly increases performance for the
noncached case, and slightly increases it for the cached case.
This can be changed by the user on mount (specifying bsize=
values from 16K to 16MB) to tune better for performance
for applications that depend on blocksize.
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When we have a READ lease for a file and have just issued a write
operation to the server we need to purge the cache and set oplock/lease
level to NONE to avoid reading stale data. Currently we do that
only if a write operation succedeed thus not covering cases when
a request was sent to the server but a negative error code was
returned later for some other reasons (e.g. -EIOCBQUEUED or -EINTR).
Fix this by turning off caching regardless of the error code being
returned.
The patches fixes generic tests 075 and 112 from the xfs-tests.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When we hit failures during constructing MIDs or sending PDUs
through the network, we end up not using message IDs assigned
to the packet. The next SMB packet will skip those message IDs
and continue with the next one. This behavior may lead to a server
not granting us credits until we use the skipped IDs. Fix this by
reverting the current ID to the original value if any errors occur
before we push the packet through the network stack.
This patch fixes the generic/310 test from the xfs-tests.
Cc: <stable@vger.kernel.org> # 4.19.x Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Currently on lease break the client sets a caching level twice:
when oplock is detected and when oplock is processed. While the
1st attempt sets the level to the value provided by the server,
the 2nd one resets the level to None unconditionally.
This happens because the oplock/lease processing code was changed
to avoid races between page cache flushes and oplock breaks.
The commit c11f1df5003d534 ("cifs: Wait for writebacks to complete
before attempting write.") fixed the races for oplocks but didn't
apply the same changes for leases resulting in overwriting the
server granted value to None. Fix this by properly processing
lease breaks.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If we don't find a writable file handle when retrying writepages
we break of the loop and do not unlock and put pages neither from
wdata2 nor from the original wdata. Fix this by walking through
all the remaining pages and cleanup them properly.
Cc: <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 5092fcf34908 ("crypto: arm64/aes-ce-ccm: add non-SIMD generic
fallback") introduced C fallback code to replace the NEON routines
when invoked from a context where the NEON is not available (i.e.,
from the context of a softirq taken while the NEON is already being
used in kernel process context)
Fix two logical flaws in the MAC calculation of the associated data.
The NEON MAC calculation routine fails to handle the case correctly
where there is some data in the buffer, and the input fills it up
exactly. In this case, we enter the loop at the end with w8 == 0,
while a negative value is assumed, and so the loop carries on until
the increment of the 32-bit counter wraps around, which is quite
obviously wrong.
So omit the loop altogether in this case, and exit right away.
Reported-by: Eric Biggers <ebiggers@kernel.org> Fixes: a3fd82105b9d1 ("arm64/crypto: AES in CCM mode using ARMv8 Crypto ...") Cc: stable@vger.kernel.org Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The x86 MORUS implementations all fail the improved AEAD tests because
they produce the wrong result with some data layouts. The issue is that
they assume that if the skcipher_walk API gives 'nbytes' not aligned to
the walksize (a.k.a. walk.stride), then it is the end of the data. In
fact, this can happen before the end.
Also, when the CRYPTO_TFM_REQ_MAY_SLEEP flag is given, they can
incorrectly sleep in the skcipher_walk_*() functions while preemption
has been disabled by kernel_fpu_begin().
Fix these bugs.
Fixes: 56e8e57fc3a7 ("crypto: morus - Add common SIMD glue code for MORUS") Cc: <stable@vger.kernel.org> # v4.18+ Cc: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
gcmaes_crypt_by_sg() dereferences the NULL pointer returned by
scatterwalk_ffwd() when encrypting an empty plaintext and the source
scatterlist ends immediately after the associated data.
Fix it by only fast-forwarding to the src/dst data scatterlists if the
data length is nonzero.
This bug is reproduced by the "rfc4543(gcm(aes))" test vectors when run
with the new AEAD test manager.
Fixes: e845520707f8 ("crypto: aesni - Update aesni-intel_glue to use scatter/gather") Cc: <stable@vger.kernel.org> # v4.17+ Cc: Dave Watson <davejwatson@fb.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The x86 AEGIS implementations all fail the improved AEAD tests because
they produce the wrong result with some data layouts. The issue is that
they assume that if the skcipher_walk API gives 'nbytes' not aligned to
the walksize (a.k.a. walk.stride), then it is the end of the data. In
fact, this can happen before the end.
Also, when the CRYPTO_TFM_REQ_MAY_SLEEP flag is given, they can
incorrectly sleep in the skcipher_walk_*() functions while preemption
has been disabled by kernel_fpu_begin().
Fix these bugs.
Fixes: 1d373d4e8e15 ("crypto: x86 - Add optimized AEGIS implementations") Cc: <stable@vger.kernel.org> # v4.18+ Cc: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Instantiating "cryptd(crc32c)" causes a crypto self-test failure because
the crypto_alloc_shash() in alg_test_crc32c() fails. This is because
cryptd(crc32c) is an ahash algorithm, not a shash algorithm; so it can
only be accessed through the ahash API, unlike shash algorithms which
can be accessed through both the ahash and shash APIs.
As the test is testing the shash descriptor format which is only
applicable to shash algorithms, skip it for ahash algorithms.
(Note that it's still important to fix crypto self-test failures even
for weird algorithm instantiations like cryptd(crc32c) that no one
would really use; in fips_enabled mode unprivileged users can use them
to panic the kernel, and also they prevent treating a crypto self-test
failure as a bug when fuzzing the kernel.)
Fixes: 8e3ee85e68c5 ("crypto: crc32c - Test descriptor context format") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Some algorithms have a ->setkey() method that is not atomic, in the
sense that setting a key can fail after changes were already made to the
tfm context. In this case, if a key was already set the tfm can end up
in a state that corresponds to neither the old key nor the new key.
For example, in lrw.c, if gf128mul_init_64k_bbe() fails due to lack of
memory, then priv::table will be left NULL. After that, encryption with
that tfm will cause a NULL pointer dereference.
It's not feasible to make all ->setkey() methods atomic, especially ones
that have to key multiple sub-tfms. Therefore, make the crypto API set
CRYPTO_TFM_NEED_KEY if ->setkey() fails and the algorithm requires a
key, to prevent the tfm from being used until a new key is set.
[Cc stable mainly because when introducing the NEED_KEY flag I changed
AF_ALG to rely on it; and unlike in-kernel crypto API users, AF_ALG
previously didn't have this problem. So these "incompletely keyed"
states became theoretically accessible via AF_ALG -- though, the
opportunities for causing real mischief seem pretty limited.]
Fixes: f8d33fac8480 ("crypto: skcipher - prevent using skciphers without setting key") Cc: <stable@vger.kernel.org> # v4.16+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The memcpy()s in the PCBC implementation use walk->iv as both the source
and destination, which has undefined behavior. These memcpy()'s are
actually unneeded, because walk->iv is already used to hold the previous
plaintext block XOR'd with the previous ciphertext block. Thus,
walk->iv is already updated to its final value.
The generic MORUS implementations all fail the improved AEAD tests
because they produce the wrong result with some data layouts. The issue
is that they assume that if the skcipher_walk API gives 'nbytes' not
aligned to the walksize (a.k.a. walk.stride), then it is the end of the
data. In fact, this can happen before the end. Fix them.
Fixes: 396be41f16fd ("crypto: morus - Add generic MORUS AEAD implementations") Cc: <stable@vger.kernel.org> # v4.18+ Cc: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Some algorithms have a ->setkey() method that is not atomic, in the
sense that setting a key can fail after changes were already made to the
tfm context. In this case, if a key was already set the tfm can end up
in a state that corresponds to neither the old key nor the new key.
It's not feasible to make all ->setkey() methods atomic, especially ones
that have to key multiple sub-tfms. Therefore, make the crypto API set
CRYPTO_TFM_NEED_KEY if ->setkey() fails and the algorithm requires a
key, to prevent the tfm from being used until a new key is set.
Note: we can't set CRYPTO_TFM_NEED_KEY for OPTIONAL_KEY algorithms, so
->setkey() for those must nevertheless be atomic. That's fine for now
since only the crc32 and crc32c algorithms set OPTIONAL_KEY, and it's
not intended that OPTIONAL_KEY be used much.
[Cc stable mainly because when introducing the NEED_KEY flag I changed
AF_ALG to rely on it; and unlike in-kernel crypto API users, AF_ALG
previously didn't have this problem. So these "incompletely keyed"
states became theoretically accessible via AF_ALG -- though, the
opportunities for causing real mischief seem pretty limited.]
Fixes: 9fa68f620041 ("crypto: hash - prevent using keyed hashes without setting key") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The SIMD routine ported from x86 used to have a special code path
for inputs < 16 bytes, which got lost somewhere along the way.
Instead, the current glue code aligns the input pointer to 16 bytes,
which is not really necessary on this architecture (although it
could be beneficial to performance to expose aligned data to the
the NEON routine), but this could result in inputs of less than
16 bytes to be passed in. This not only fails the new extended
tests that Eric has implemented, it also results in the code
reading past the end of the input, which could potentially result
in crashes when dealing with less than 16 bytes of input at the
end of a page which is followed by an unmapped page.
So update the glue code to only invoke the NEON routine if the
input is at least 16 bytes.
Reported-by: Eric Biggers <ebiggers@kernel.org> Reviewed-by: Eric Biggers <ebiggers@kernel.org> Fixes: 6ef5737f3931 ("crypto: arm64/crct10dif - port x86 SSE implementation to arm64") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The arm64 NEON bit-sliced implementation of AES-CTR fails the improved
skcipher tests because it sometimes produces the wrong ciphertext. The
bug is that the final keystream block isn't returned from the assembly
code when the number of non-final blocks is zero. This can happen if
the input data ends a few bytes after a page boundary. In this case the
last bytes get "encrypted" by XOR'ing them with uninitialized memory.
Fix the assembly code to return the final keystream block when needed.
Fixes: 88a3f582bea9 ("crypto: arm64/aes - don't use IV buffer to return final keystream block") Cc: <stable@vger.kernel.org> # v4.11+ Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The SIMD routine ported from x86 used to have a special code path
for inputs < 16 bytes, which got lost somewhere along the way.
Instead, the current glue code aligns the input pointer to permit
the NEON routine to use special versions of the vld1 instructions
that assume 16 byte alignment, but this could result in inputs of
less than 16 bytes to be passed in. This not only fails the new
extended tests that Eric has implemented, it also results in the
code reading past the end of the input, which could potentially
result in crashes when dealing with less than 16 bytes of input
at the end of a page which is followed by an unmapped page.
So update the glue code to only invoke the NEON routine if the
input is at least 16 bytes.
Reported-by: Eric Biggers <ebiggers@kernel.org> Reviewed-by: Eric Biggers <ebiggers@kernel.org> Fixes: 1d481f1cd892 ("crypto: arm/crct10dif - port x86 SSE implementation to ARM") Cc: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The generic AEGIS implementations all fail the improved AEAD tests
because they produce the wrong result with some data layouts. The issue
is that they assume that if the skcipher_walk API gives 'nbytes' not
aligned to the walksize (a.k.a. walk.stride), then it is the end of the
data. In fact, this can happen before the end. Fix them.
Fixes: f606a88e5823 ("crypto: aegis - Add generic AEGIS AEAD implementations") Cc: <stable@vger.kernel.org> # v4.18+ Cc: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Some algorithms have a ->setkey() method that is not atomic, in the
sense that setting a key can fail after changes were already made to the
tfm context. In this case, if a key was already set the tfm can end up
in a state that corresponds to neither the old key nor the new key.
For example, in gcm.c, if the kzalloc() fails due to lack of memory,
then the CTR part of GCM will have the new key but GHASH will not.
It's not feasible to make all ->setkey() methods atomic, especially ones
that have to key multiple sub-tfms. Therefore, make the crypto API set
CRYPTO_TFM_NEED_KEY if ->setkey() fails, to prevent the tfm from being
used until a new key is set.
[Cc stable mainly because when introducing the NEED_KEY flag I changed
AF_ALG to rely on it; and unlike in-kernel crypto API users, AF_ALG
previously didn't have this problem. So these "incompletely keyed"
states became theoretically accessible via AF_ALG -- though, the
opportunities for causing real mischief seem pretty limited.]
Fixes: dc26c17f743a ("crypto: aead - prevent using AEADs without setting key") Cc: <stable@vger.kernel.org> # v4.16+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
same story as with last May fixes in sysfs (7b745a4e4051
"unfuck sysfs_mount()"); new_sb is left uninitialized
in case of early errors in kernfs_mount_ns() and papering
over it by treating any error from kernfs_mount_ns() as
equivalent to !new_ns ends up conflating the cases when
objects had never been transferred to a superblock with
ones when that has happened and resulting new superblock
had been dropped. Easily fixed (same way as in sysfs
case). Additionally, there's a superblock leak on
kernfs_node_dentry() failure *and* a dentry leak inside
kernfs_node_dentry() itself - the latter on probably
impossible errors, but the former not impossible to trigger
(as the matter of fact, injecting allocation failures
at that point *does* trigger it).
Libnvdimm reserves the first 8K of pfn and devicedax namespaces to
store a superblock describing the namespace. This 8K reservation
is contained within the altmap area which the kernel uses for the
vmemmap backing for the pages within the namespace. The altmap
allows for some pages at the start of the altmap area to be reserved
and that mechanism is used to protect the superblock from being
re-used as vmemmap backing.
The number of PFNs to reserve is calculated using:
So on systems where PAGE_SIZE is greater than 8K the reservation
size is truncated to zero and the superblock area is re-used as
vmemmap backing. As a result all the namespace information stored
in the superblock (i.e. if it's a PFN or DAX namespace) is lost
and the namespace needs to be re-created to get access to the
contents.
This patch fixes this by using PFN_UP() rather than PHYS_PFN() to ensure
that at least one page is reserved. On systems with a 4K pages size this
patch should have no effect.
Cc: stable@vger.kernel.org Cc: Dan Williams <dan.j.williams@intel.com> Fixes: ac515c084be9 ("libnvdimm, pmem, pfn: move pfn setup to the core") Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For recovery, where non-dax access is needed to a given physical address
range, and testing, allow the 'force_raw' attribute to override the
default establishment of a dev_pagemap.
Otherwise without this capability it is possible to end up with a
namespace that can not be activated due to corrupted info-block, and one
that can not be repaired due to a section collision.
Cc: <stable@vger.kernel.org> Fixes: 004f1afbe199 ("libnvdimm, pmem: direct map legacy pmem by default") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
When trying to see whether current nd_region intersects with others,
trim_pfn_device() has already calculated the *size* to be expanded to
SECTION size.
Do not double append 'adjust' to 'size' when calculating whether the end
of a region collides with the next pmem region.
Fixes: ae86cbfef381 "libnvdimm, pfn: Pad pfn namespaces relative to other regions" Cc: <stable@vger.kernel.org> Signed-off-by: Wei Yang <richardw.yang@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The UEFI 2.7 specification sets expectations that the 'updating' flag is
eventually cleared. To date, the libnvdimm core has never adhered to
that protocol. The policy of the core matches the policy of other
multi-device info-block formats like MD-Software-RAID that expect
administrator intervention on inconsistent info-blocks, not automatic
invalidation.
However, some pre-boot environments may unfortunately attempt to "clean
up" the labels and invalidate a set when it fails to find at least one
"non-updating" label in the set. Clear the updating flag after set
updates to minimize the window of vulnerability to aggressive pre-boot
environments.
Ideally implementations would not write to the label area outside of
creating namespaces.
Note that this only minimizes the window, it does not close it as the
system can still crash while clearing the flag and the set can be
subsequently deleted / invalidated by the pre-boot environment.
Fixes: f524bf271a5c ("libnvdimm: write pmem label set") Cc: <stable@vger.kernel.org> Cc: Kelly Couch <kelly.j.couch@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 11189c1089da "acpi/nfit: Fix command-supported detection" broke
ND_CMD_CALL for bus-level commands. The "func = cmd" assumption is only
valid for:
The implementation is broken in all the ways the unit test did not touch:
1/ The local definition of in_buf and in_obj violated C99 initializer
expectations for zeroing. By only initializing 2 out of the three
struct members the compiler was free to zero-initialize the remaining
entry even though the aliased location in the union was initialized.
2/ The implementation made assumptions about the state of the 'smart'
payload after command execution that are satisfied by
acpi_nfit_ctl(), but not acpi_evaluate_dsm().
3/ populate_shutdown_status() is skipped on Intel NVDIMMs due to the early
return for skipping the common _LS{I,R,W} enabling.
4/ The input length should be zero.
This breakage was missed due to the unit test implementation only
testing the case where nfit_intel_shutdown_status() returns a valid
payload.
Much of this complexity would be saved if acpi_nfit_ctl() could be used, but
that currently requires a 'struct nvdimm *' argument and one is not created
until later in the init process. The health result is needed before the device
is created because the payload gates whether the nmemX/nfit/dirty_shutdown
property is visible in sysfs.
Cc: <stable@vger.kernel.org> Fixes: 0ead11181fe0 ("acpi, nfit: Collect shutdown status") Reported-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The radix tree would rewind the index in an iterator to the lowest index
of a multi-slot entry. The XArray iterators instead leave the index
unchanged, but I overlooked that when converting DAX from the radix tree
to the XArray. Adjust the index that we use for flushing to the start
of the PMD range.
Fixes: c1901cd33cf4 ("page cache: Convert find_get_entries_tag to XArray") Cc: <stable@vger.kernel.org> Reported-by: Piotr Balcer <piotr.balcer@intel.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Matthew Wilcox <willy@infradead.org> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For chain mode in cipher(eg. AES-CBC/DES-CBC), the iv is continuously
updated in the operation. The new iv value should be written to device
register by software.
Hash algorithms with an alignmask set, e.g. "xcbc(aes-aesni)" and
"michael_mic", fail the improved hash tests because they sometimes
produce the wrong digest. The bug is that in the case where a
scatterlist element crosses pages, not all the data is actually hashed
because the scatterlist walk terminates too early. This happens because
the 'nbytes' variable in crypto_hash_walk_done() is assigned the number
of bytes remaining in the page, then later interpreted as the number of
bytes remaining in the scatterlist element. Fix it.
Fixes: 900a081f6912 ("crypto: ahash - Fix early termination in hash walk") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
1. It stored the per-request state 'cnt' in the tfm context, which can be
used by multiple threads concurrently (e.g. via AF_ALG).
2. It didn't support messages not a multiple of the block cipher size,
despite being a stream cipher.
3. It didn't set cra_blocksize to 1 to indicate it is a stream cipher.
To fix these, set the 'chunksize' property to the cipher block size to
guarantee that when walking through the scatterlist, a partial block can
only occur at the end. Then change the implementation to XOR a block at
a time at first, then XOR the partial block at the end if needed. This
is the same way CTR and CFB are implemented. As a bonus, this also
improves performance in most cases over the current approach.
The memcpy() in crypto_cfb_decrypt_inplace() uses walk->iv as both the
source and destination, which has undefined behavior. It is unneeded
because walk->iv is already used to hold the previous ciphertext block;
thus, walk->iv is already updated to its final value. So, remove it.
Also, note that in-place decryption is the only case where the previous
ciphertext block is not directly available. Therefore, as a related
cleanup I also updated crypto_cfb_encrypt_segment() to directly use the
previous ciphertext block rather than save it into walk->iv. This makes
it consistent with in-place encryption and out-of-place decryption; now
only in-place decryption is different, because it has to be.
Fixes: a7d85e06ed80 ("crypto: cfb - add support for Cipher FeedBack mode") Cc: <stable@vger.kernel.org> # v4.17+ Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Like some other block cipher mode implementations, the CFB
implementation assumes that while walking through the scatterlist, a
partial block does not occur until the end. But the walk is incorrectly
being done with a blocksize of 1, as 'cra_blocksize' is set to 1 (since
CFB is a stream cipher) but no 'chunksize' is set. This bug causes
incorrect encryption/decryption for some scatterlist layouts.
Fix it by setting the 'chunksize'. Also extend the CFB test vectors to
cover this bug as well as cases where the message length is not a
multiple of the block size.
Fixes: a7d85e06ed80 ("crypto: cfb - add support for Cipher FeedBack mode") Cc: <stable@vger.kernel.org> # v4.17+ Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
For decryption in CBC mode we need to save the last ciphertext block
for use as the next IV. However, we were trying to do this also with
zero sized ciphertext resulting in a panic.
Fix this by only doing the copy if the ciphertext length is at least
of IV size.
We were copying the last ciphertext block into the IV field
for CBC before removing the DMA mapping of the output buffer
with the result of the buffer sometime being out-of-sync cache
wise and were getting intermittent cases of bad output IV.
Fix it by moving the DMA buffer unmapping before the copy.
In cc_unmap_aead_request(), call dma_pool_free() for mlli buffer only
if an item is allocated from the pool and not always if there is a
pool allocated.
This fixes a kernel panic when trying to free a non-allocated item.
Roland reports the following issue and provides a root cause analysis:
"On a v4.19 i.MX6 system with IMA and CONFIG_DMA_API_DEBUG enabled, a
warning is generated when accessing files on a filesystem for which IMA
measurement is enabled:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/dma/debug.c:1181 check_for_stack.part.9+0xd0/0x120
caam_jr 2101000.jr0: DMA-API: device driver maps memory from stack [addr=b668049e]
Modules linked in:
CPU: 0 PID: 1 Comm: switch_root Not tainted 4.19.0-20181214-1 #2
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<c010efb8>] (dump_backtrace) from [<c010f2d0>] (show_stack+0x20/0x24)
[<c010f2b0>] (show_stack) from [<c08b04f4>] (dump_stack+0xa0/0xcc)
[<c08b0454>] (dump_stack) from [<c012b610>] (__warn+0xf0/0x108)
[<c012b520>] (__warn) from [<c012b680>] (warn_slowpath_fmt+0x58/0x74)
[<c012b62c>] (warn_slowpath_fmt) from [<c0199acc>] (check_for_stack.part.9+0xd0/0x120)
[<c01999fc>] (check_for_stack.part.9) from [<c019a040>] (debug_dma_map_page+0x144/0x174)
[<c0199efc>] (debug_dma_map_page) from [<c065f7f4>] (ahash_final_ctx+0x5b4/0xcf0)
[<c065f240>] (ahash_final_ctx) from [<c065b3c4>] (ahash_final+0x1c/0x20)
[<c065b3a8>] (ahash_final) from [<c03fe278>] (crypto_ahash_op+0x38/0x80)
[<c03fe240>] (crypto_ahash_op) from [<c03fe2e0>] (crypto_ahash_final+0x20/0x24)
[<c03fe2c0>] (crypto_ahash_final) from [<c03f19a8>] (ima_calc_file_hash+0x29c/0xa40)
[<c03f170c>] (ima_calc_file_hash) from [<c03f2b24>] (ima_collect_measurement+0x1dc/0x240)
[<c03f2948>] (ima_collect_measurement) from [<c03f0a60>] (process_measurement+0x4c4/0x6b8)
[<c03f059c>] (process_measurement) from [<c03f0cdc>] (ima_file_check+0x88/0xa4)
[<c03f0c54>] (ima_file_check) from [<c02d8adc>] (path_openat+0x5d8/0x1364)
[<c02d8504>] (path_openat) from [<c02dad24>] (do_filp_open+0x84/0xf0)
[<c02daca0>] (do_filp_open) from [<c02cf50c>] (do_open_execat+0x84/0x1b0)
[<c02cf488>] (do_open_execat) from [<c02d1058>] (__do_execve_file+0x43c/0x890)
[<c02d0c1c>] (__do_execve_file) from [<c02d1770>] (sys_execve+0x44/0x4c)
[<c02d172c>] (sys_execve) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
---[ end trace 3455789a10e3aefd ]---
The cause is that the struct ahash_request *req is created as a
stack-local variable up in the stack (presumably somewhere in the IMA
implementation), then passed down into the CAAM driver, which tries to
dma_single_map the req->result (indirectly via map_seq_out_ptr_result)
in order to make that buffer available for the CAAM to store the result
of the following hash operation.
The calling code doesn't know how req will be used by the CAAM driver,
and there could be other such occurrences where stack memory is passed
down to the CAAM driver. Therefore we should rather fix this issue in
the CAAM driver where the requirements are known."
Fix this problem by:
-instructing the crypto engine to write the final hash in state->caam_ctx
-subsequently memcpy-ing the final hash into req->result
Cc: <stable@vger.kernel.org> # v4.19+ Reported-by: Roland Hieber <rhi@pengutronix.de> Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Tested-by: Roland Hieber <rhi@pengutronix.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
There is a bug in the channel allocation logic that leads to an endless
loop when looking for a contiguous range of channels in a range with a
mixture of free and occupied channels. For example, opening three
consequtive channels, closing the first two and requesting 4 channels in
a row will trigger this soft lockup. The bug is that the search loop
forgets to skip over the range once it detects that one channel in that
range is occupied.
Restore the original intent to the logic by fixing the omission.
Signed-off-by: Zhi Jin <zhi.jin@intel.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: 7bd1d4093c2f ("stm class: Introduce an abstraction for System Trace Module devices") CC: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Using STP_POLICY_ID_SET ioctl command with dummy_stm device, or any STM
device that supplies zero mmio channel size, will trigger a division by
zero bug in the kernel.
Prevent this by disallowing channel widths other than 1 for such devices.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Fixes: 7bd1d4093c2f ("stm class: Introduce an abstraction for System Trace Module devices") CC: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fix unbalanced module reference counting during internal reset, which
prevents the drivers unloading.
Tracking mei_me/txe modules on mei client bus via
mei_cldev_enable/disable is error prone due to possible internal
reset flow, where clients are disconnected underneath.
Moving reference counting to probe and release of mei bus client
driver solves this issue in simplest way, as each client provides only
a single connection to a client bus driver.
Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Fix NULL pointer exception on device unbind when device tree does not
contain "has-touchscreen" property. In such case the input device is
not registered so it should not be unregistered.
Unable to handle kernel NULL pointer dereference at virtual address 00000474
...
(input_unregister_device) from [<c0772060>] (exynos_adc_remove+0x20/0x80)
(exynos_adc_remove) from [<c0587d5c>] (platform_drv_remove+0x20/0x40)
(platform_drv_remove) from [<c05860f0>] (device_release_driver_internal+0xdc/0x1ac)
(device_release_driver_internal) from [<c0583ecc>] (unbind_store+0x60/0xd4)
(unbind_store) from [<c031b89c>] (kernfs_fop_write+0x100/0x1e0)
(kernfs_fop_write) from [<c029709c>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c0297374>] (vfs_write+0xa4/0x184)
(vfs_write) from [<c0297594>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
The ADCs are sleeping when the SLEEP bit is set and running when it's
cleared, so the bit should be inverted.
Tested on pcm1863.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
According to DS, the gain is between -12 dB and 40 dB, with a 0.5 dB step.
Tested on pcm1863.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Use inode->i_lock to protect i_size_write(), else i_size_read() in
generic_fillattr() may loop infinitely in read_seqcount_begin() when
multiple processes invoke v9fs_vfs_getattr() or v9fs_vfs_getattr_dotl()
simultaneously under 32-bit SMP environment, and a soft lockup will be
triggered as show below:
watchdog: BUG: soft lockup - CPU#5 stuck for 22s! [stat:2217]
Modules linked in:
CPU: 5 PID: 2217 Comm: stat Not tainted 5.0.0-rc1-00005-g7f702faf5a9e #4
Hardware name: Generic DT based system
PC is at generic_fillattr+0x104/0x108
LR is at 0xec497f00
pc : [<802b8898>] lr : [<ec497f00>] psr: 200c0013
sp : ec497e20 ip : ed608030 fp : ec497e3c
r10: 00000000 r9 : ec497f00 r8 : ed608030
r7 : ec497ebc r6 : ec497f00 r5 : ee5c1550 r4 : ee005780
r3 : 0000052d r2 : 00000000 r1 : ec497f00 r0 : ed608030
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: ac48006a DAC: 00000051
CPU: 5 PID: 2217 Comm: stat Not tainted 5.0.0-rc1-00005-g7f702faf5a9e #4
Hardware name: Generic DT based system
Backtrace:
[<8010d974>] (dump_backtrace) from [<8010dc88>] (show_stack+0x20/0x24)
[<8010dc68>] (show_stack) from [<80a1d194>] (dump_stack+0xb0/0xdc)
[<80a1d0e4>] (dump_stack) from [<80109f34>] (show_regs+0x1c/0x20)
[<80109f18>] (show_regs) from [<801d0a80>] (watchdog_timer_fn+0x280/0x2f8)
[<801d0800>] (watchdog_timer_fn) from [<80198658>] (__hrtimer_run_queues+0x18c/0x380)
[<801984cc>] (__hrtimer_run_queues) from [<80198e60>] (hrtimer_run_queues+0xb8/0xf0)
[<80198da8>] (hrtimer_run_queues) from [<801973e8>] (run_local_timers+0x28/0x64)
[<801973c0>] (run_local_timers) from [<80197460>] (update_process_times+0x3c/0x6c)
[<80197424>] (update_process_times) from [<801ab2b8>] (tick_nohz_handler+0xe0/0x1bc)
[<801ab1d8>] (tick_nohz_handler) from [<80843050>] (arch_timer_handler_virt+0x38/0x48)
[<80843018>] (arch_timer_handler_virt) from [<80180a64>] (handle_percpu_devid_irq+0x8c/0x240)
[<801809d8>] (handle_percpu_devid_irq) from [<8017ac20>] (generic_handle_irq+0x34/0x44)
[<8017abec>] (generic_handle_irq) from [<8017b344>] (__handle_domain_irq+0x6c/0xc4)
[<8017b2d8>] (__handle_domain_irq) from [<801022e0>] (gic_handle_irq+0x4c/0x88)
[<80102294>] (gic_handle_irq) from [<80101a30>] (__irq_svc+0x70/0x98)
[<802b8794>] (generic_fillattr) from [<8056b284>] (v9fs_vfs_getattr_dotl+0x74/0xa4)
[<8056b210>] (v9fs_vfs_getattr_dotl) from [<802b8904>] (vfs_getattr_nosec+0x68/0x7c)
[<802b889c>] (vfs_getattr_nosec) from [<802b895c>] (vfs_getattr+0x44/0x48)
[<802b8918>] (vfs_getattr) from [<802b8a74>] (vfs_statx+0x9c/0xec)
[<802b89d8>] (vfs_statx) from [<802b9428>] (sys_lstat64+0x48/0x78)
[<802b93e0>] (sys_lstat64) from [<80101000>] (ret_fast_syscall+0x0/0x28)
[dominique.martinet@cea.fr: updated comment to not refer to a function
in another subsystem] Link: http://lkml.kernel.org/r/20190124063514.8571-2-houtao1@huawei.com Cc: stable@vger.kernel.org Fixes: 7549ae3e81cc ("9p: Use the i_size_[read, write]() macros instead of using inode->i_size directly.") Reported-by: Xing Gaopeng <xingaopeng@huawei.com> Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Fixes: 2bf9a0a12749b ('iommu/amd: Add iommu support for ACPI HID devices') Signed-off-by: Joerg Roedel <jroedel@suse.de>
(cherry picked from commit bb6bccba390c7d743c1e4427de4ef284c8cc6869) Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Hui Wang [Wed, 20 Mar 2019 01:47:18 +0000 (09:47 +0800)]
ALSA: hda - Don't trigger jackpoll_work in azx_resume
BugLink: http://bugs.launchpad.net/bugs/1820930
The commit 3baffc4a84d7 (ALSA: hda/intel: Refactoring PM code) changed
the behaviour of azx_resume(), it triggers the jackpoll_work after
applying this commit.
This change introduced a new issue, all codecs are runtime active
after S3, and will not call runtime_suspend() automatically.
The root cause is the jackpoll_work calls snd_hda_power_up/down_pm,
and it calls up_pm before snd_hdac_enter_pm is called, while calls
the down_pm in the middle of enter_pm and leave_pm is called. This
makes the dev->power.usage_count unbalanced after S3.
To fix it, let azx_resume() don't trigger jackpoll_work as before
it did.
Fixes: 3baffc4a84d7 ("ALSA: hda/intel: Refactoring PM code") Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit 744c67ffeb06f2d2493f4049ba0bd19698ce0adf
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Hui Wang [Wed, 20 Mar 2019 01:47:17 +0000 (09:47 +0800)]
ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec
BugLink: http://bugs.launchpad.net/bugs/1820930
Recently we found the audio jack detection stop working after suspend
on many machines with Realtek codec. Sometimes the audio selection
dialogue didn't show up after users plugged headhphone/headset into
the headset jack, sometimes after uses plugged headphone/headset, then
click the sound icon on the upper-right corner of gnome-desktop, it
also showed the speaker rather than the headphone.
The root cause is that before suspend, the codec already call the
runtime_suspend since this codec is not used by any apps, then in
resume, it will not call runtime_resume for this codec. But for some
realtek codec (so far, alc236, alc255 and alc891) with the specific
BIOS, if it doesn't run runtime_resume after suspend, all codec
functions including jack detection stop working anymore.
This problem existed for a long time, but it was not exposed, that is
because when problem happens, if users play sound or open
sound-setting to check audio device, this will trigger calling to
runtime_resume (via snd_hda_power_up), then the codec starts working
again before users notice this problem.
Since we don't know how many codec and BIOS combinations have this
problem, to fix it, let the driver call runtime_resume for all codecs
in pm_resume, maybe for some codecs, this is not needed, but it is
harmless. After a codec is runtime resumed, if it is not used by any
apps, it will be runtime suspended soon and furthermore we don't run
suspend frequently, this change will not add much power consumption.
Fixes: cc72da7d4d06 ("ALSA: hda - Use standard runtime PM for codec power-save control") Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
(backported from commit b5a236c175b0d984552a5f7c9d35141024c2b261
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git) Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Ignat Loskutov [Fri, 1 Mar 2019 13:43:45 +0000 (16:43 +0300)]
UBUNTU: [Packaging] fix a mistype
BugLink: https://bugs.launchpad.net/bugs/1396654
HAVE_CPLUS_DEMANGLE_SUPPORT=1 used to be spelled incorrectly, leading to
missing C++ demangling support in perf.
Mika Westerberg [Tue, 26 Feb 2019 08:56:57 +0000 (16:56 +0800)]
PCI: pciehp: Disable Data Link Layer State Changed event on suspend
BugLink: https://bugs.launchpad.net/bugs/1817676
Commit 0e157e528604 ("PCI/PME: Implement runtime PM callbacks") tried to
solve an issue where the hierarchy immediately wakes up when it is
transitioned into D3cold. However, it turns out to prevent PME
propagation on some systems that do not support D3cold.
I looked more closely at what might cause the immediate wakeup. It happens
when the ACPI power resource of the root port is turned off. The AML code
associated with the _OFF() method of the ACPI power resource starts a PCIe
L2/L3 Ready transition and waits for it to complete. Right after the L2/L3
Ready transition is started the root port receives a PME from the
downstream port.
The simplest hierarchy where this happens looks like this:
00:1d.0 PCIe Root Port
^
|
v
05:00.0 PCIe switch #1 upstream port
06:01.0 PCIe switch #1 downstream hotplug port
^
|
v
08:00.0 PCIe switch #2 upstream port
It seems that the PCIe link between the two switches, before
PME_Turn_Off/PME_TO_Ack is complete for the whole hierarchy, goes
inactive and triggers PME towards the root port bringing it back to D0.
The L2/L3 Ready sequence is described in PCIe r4.0 spec sections 5.2 and
5.3.3 but unfortunately they do not state what happens if DLLSCE is
enabled during the sequence.
Disabling Data Link Layer State Changed event (DLLSCE) seems to prevent
the issue and still allows the downstream hotplug port to notice when a
device is plugged/unplugged.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202593 Fixes: 0e157e528604 ("PCI/PME: Implement runtime PM callbacks") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: stable@vger.kernel.org # v4.20+
(cherry picked from commit bbe54ea5330d828cc396d451c0e1e5c3f9764c1e) Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Acked-By: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
In reshape_request it already adds len to sector_nr already. It's wrong to add len to
sector_nr again after adding pages to bio. If there is bad block it can't copy one chunk
at a time, it needs to goto read_more. Now the sector_nr is wrong. It can cause data
corruption.
Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The Acer TravelMate X514-51T with ALC255 cannot detect the headset MIC
until ALC255_FIXUP_ACER_HEADSET_MIC quirk applied. Although, the
internal DMIC uses another module - snd_soc_skl as the driver. We still
need the NID 0x1a in the quirk to enable the headset MIC.
Dell Precision 5820 with ALC3234 codec (which is equivalent with
ALC255) shows click noises at (runtime) PM resume on the headphone.
The biggest source of the noise comes from the cleared headphone pin
control at resume, which is done via the standard shutup procedure.
Although we have an override of the standard shutup callback to
replace with NOP, this would skip other needed stuff (e.g. the pull
down of headset power). So, instead, this "fixes" the behavior of
alc_fixup_no_shutup() by introducing spec->no_shutup_pins flag.
When this flag is set, Realtek codec won't call the standard
snd_hda_shutup_pins() & co. Now alc_fixup_no_shutup() just sets this
flag instead of overriding spec->shutup callback itself. This allows
us to apply the similar fix for other entries easily if needed in
future.
The ASUS UX362FA with ALC294 cannot detect the headset MIC and outputs
through the internal speaker and the headphone. This issue can be fixed
by the quirk in the commit 4e0511067 ALSA: hda/realtek: Enable audio
jacks of ASUS UX533FD with ALC294.
Besides, ASUS UX362FA and UX533FD have the same audio initial pin config
values. So, this patch replaces SND_PCI_QUIRK of UX533FD with a new
SND_HDA_PIN_QUIRK which benefits both UX362FA and UX533FD.
Fixes: 4e051106730d ("ALSA: hda/realtek: Enable audio jacks of ASUS UX533FD with ALC294") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Ming Shuo Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
projects / mirror_ubuntu-disco-kernel.git / log