Brian Norris [Fri, 29 Jan 2016 19:25:33 +0000 (11:25 -0800)]
mtd: spi-nor: disallow further writes to SR if WP# is low
Locking the flash is most useful if it provides real hardware security.
Otherwise, it's little more than a software permission bit.
A reasonable use case that provides real HW security might be like
follows:
(1) hardware WP# is deasserted
(2) program flash
(3) flash range is protected via status register
(4) hardware WP# is asserted
(5) flash protection range can no longer be changed, until WP# is
deasserted
In this way, flash protection is co-owned by hardware and software.
Now, one would expect to be able to perform step (3) with
ioctl(MEMLOCK), except that the spi-nor driver does not set the Status
Register Protect bit (a.k.a. Status Register Write Disable (SRWD)), so
even though the range is now locked, it does not satisfy step (5) -- it
can still be changed by a call to ioctl(MEMUNLOCK).
So, let's enable status register protection after the first lock
command, and disable protection only when the flash is fully unlocked.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Brian Norris [Fri, 29 Jan 2016 19:25:32 +0000 (11:25 -0800)]
mtd: spi-nor: make lock/unlock bounds checks more obvious and robust
There are a few different corner cases to the current logic that seem
undesirable:
* mtd_lock() with offs==0 trips a bounds issue on
ofs - mtd->erasesize < 0
* mtd_unlock() on the middle of a flash that is already unlocked will
return -EINVAL
* probably other corner cases
So, let's stop doing "smart" checks like "check the block below us",
let's just do the following:
(a) pass only non-negative offsets/lengths to stm_is_locked_sr()
(b) add a similar stm_is_unlocked_sr() function, so we can check if the
*entire* range is unlocked (and not just whether some part of it is
unlocked)
Then armed with (b), we can make lock() and unlock() much more
symmetric:
(c) short-circuit the procedure if there is no work to be done, and
(d) check the entire range above/below
This also aligns well with the structure needed for proper TB
(Top/Bottom) support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Brian Norris [Fri, 29 Jan 2016 19:25:31 +0000 (11:25 -0800)]
mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region
If, for instance, the entire flash is already unlocked and I try to
mtd_unlock() the entire device, I don't expect to see an EINVAL error.
It should just silently succeed. Ditto for mtd_lock().
Brian Norris [Fri, 29 Jan 2016 19:25:30 +0000 (11:25 -0800)]
mtd: spi-nor: wait for SR_WIP to clear on initial unlock
Fixup a piece leftover by commit 32321e950d8a ("mtd: spi-nor: wait until
lock/unlock operations are ready"). That commit made us wait for the WIP
bit to settle after lock/unlock operations, but it missed the open-coded
"unlock" that happens at probe() time.
We should probably have this code utilize the unlock() routines in the
future, to avoid duplication, but unfortunately, flash which need to be
unlocked don't all have a proper ->flash_unlock() callback.
Boris BREZILLON [Mon, 7 Mar 2016 09:46:54 +0000 (10:46 +0100)]
mtd: nand: simplify nand_bch_init() usage
nand_bch_init() requires several arguments which could directly be deduced
from the mtd device. Get rid of those useless parameters.
nand_bch_init() is also requiring the caller to provide a proper eccbytes
value, while this value could be deduced from the ecc.size and
ecc.strength value. Fallback to eccbytes calculation when it is set to 0.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON [Mon, 7 Mar 2016 09:46:53 +0000 (10:46 +0100)]
mtd: mtdswap: remove useless if (!mtd->ecclayout) test
If the MTD device does not have OOB, the mtd->oobsize and mtd->oobavail
fields are set to zero, and we are testing those values in the following
test.
Remove the useless if (!mtd->ecclayout) test.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON [Mon, 7 Mar 2016 09:46:52 +0000 (10:46 +0100)]
mtd: create an mtd_oobavail() helper and make use of it
Currently, all MTD drivers/sublayers exposing an OOB area are
doing the same kind of test to extract the available OOB size
based on the mtd_info and mtd_oob_ops structures.
Move this common logic into an inline function and make use of it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Suggested-by: Priit Laes <plaes@plaes.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON [Mon, 7 Mar 2016 09:46:51 +0000 (10:46 +0100)]
mtd: kill the ecclayout->oobavail field
ecclayout->oobavail is just redundant with the mtd->oobavail field.
Moreover, it prevents static const definition of ecc layouts since the
NAND framework is calculating this value based on the ecclayout->oobfree
field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Sat, 5 Mar 2016 01:19:23 +0000 (17:19 -0800)]
mtd: nand: check status before reporting timeout
In commit b70af9bef49b ("mtd: nand: increase ready wait timeout and
report timeouts"), we increased the likelihood of scheduling during
nand_wait(). This makes us more likely to hit the time_before(...)
condition, since a lot of time may pass before we get scheduled again.
Now, the loop was already buggy, since we don't check if the NAND is
ready after exiting the loop; we simply print out a timeout warning. Fix
this by doing a final status check before printing a timeout message.
This isn't actually a critical bug, since the only effect is a false
warning print. But too many prints never hurt anyone, did they? :)
Side note: perhaps I'm not smart enough, but I'm not sure what the best
policy is for this kind of loop; do we busy loop (i.e., no
cond_resched()) to keep the lowest I/O latency (it's not great if the
resched is delaying Richard's system ~400ms)? Or do we allow
rescheduling, to play nice with the rest of the system (since some
operations can take quite a while)?
Reported-by: Richard Weinberger <richard@nod.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Richard Weinberger <richard@nod.at> Reviewed-by: Harvey Hunt <harvey.hunt@imgtec.com>
Brian Norris [Fri, 12 Feb 2016 20:26:04 +0000 (12:26 -0800)]
mtd: bcm63xxpart: give width specifier an 'int', not 'size_t'
Fixes this warning:
>> drivers/mtd/bcm63xxpart.c:175:4: note: in expansion of macro 'pr_err'
pr_err("invalid rootfs address: %*ph\n",
^
>> include/linux/kern_levels.h:4:18: warning: field width specifier '*' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Wformat=]
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Alexander Stein [Wed, 2 Mar 2016 15:26:59 +0000 (16:26 +0100)]
mtd: mtdram: Add parameter for setting writebuf size
ubifs uses the write buffer size in recovery algorithm. When inspecting
an unclean ubifs recovery fails with writebuf size 64 in mtdram while
recovery on actual mtd device with writebuf size of 1024 succeeds.
So add a parameter for setting this property.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Reviewed-by: Richard Weinberger <richard@nod.at> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Brian Norris [Mon, 7 Mar 2016 18:37:30 +0000 (10:37 -0800)]
mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd'
With this removal, we don't need to 'get' the second DMA resource
either, as it's also unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add optional properties for QSPI:
big-endian
if the register is big endian on this platform.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Yao Yuan [Tue, 26 Jan 2016 07:23:56 +0000 (15:23 +0800)]
mtd: spi-nor: fsl-quadspi: add support for ls1021a
LS1021a also support Freescale Quad SPI controller.
Add fsl-quadspi support for ls1021a chip and make SPI_FSL_QUADSPI
selectable for LS1021A SOC hardwares.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Acked-by: Han xu <han.xu@freescale.com> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Yao Yuan [Tue, 26 Jan 2016 07:23:55 +0000 (15:23 +0800)]
mtd: spi-nor: fsl-quadspi: add big-endian support
Add R/W functions for big- or little-endian registers:
The qSPI controller's endian is independent of the CPU core's endian.
So far, the qSPI have two versions for big-endian and little-endian.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Acked-by: Han xu <han.xu@freescale.com> Acked-by: Han xu <han.xu@nxp.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the driver is initialized in a pure device-tree platform, the
driver's probe fails allocating the dma channel :
[ 525.624435] pxa3xx-nand 43100000.nand: no resource defined for data DMA
[ 525.632088] pxa3xx-nand 43100000.nand: alloc nand resource failed
The reason is that the DMA IO resource is not acquired through platform
resources but by OF bindings.
Fix this by ensuring that DMA IO resources are only queried in the non
device-tree case.
Fixes: 8f5ba31aa565 ("mtd: nand: pxa3xx-nand: switch to dmaengine") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
David Woodhouse [Mon, 1 Feb 2016 12:00:25 +0000 (12:00 +0000)]
jffs2: Improve post-mount CRC scan efficiency
We need to finish doing the CRC checks before we can allow writes to
happen, and we currently process the inodes in order. This means a call
to jffs2_get_ino_cache() for each possible inode# up to c->highest_ino.
There may be a lot of lookups which fail, if the inode# space is used
sparsely. And the inode# space is *often* used sparsely, if a file
system contains a lot of stuff that was put there in the original
image, followed by lots of creation and deletion of new files.
Instead of processing them numerically with a lookup each time, just
walk the hash buckets instead.
[fix locking typo reported by Dan Carpenter] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Florian Fainelli [Thu, 25 Feb 2016 00:07:23 +0000 (16:07 -0800)]
mtd: brcmnand: Fix v7.1 register offsets
The BRCMNAND controller revision 7.1 is almost 100% compatible with the
previous v6.0 register offset layout, except for the Correctable Error
Reporting Threshold registers. Fix this by adding another table with the
correct offsets for CORR_THRESHOLD and CORR_THRESHOLD_EXT.
Aaro Koskinen [Sat, 20 Feb 2016 20:27:48 +0000 (22:27 +0200)]
mtd: onenand: fix deadlock in onenand_block_markbad
Commit 5942ddbc500d ("mtd: introduce mtd_block_markbad interface")
incorrectly changed onenand_block_markbad() to call mtd_block_markbad
instead of onenand_chip's block_markbad function. As a result the function
will now recurse and deadlock. Fix by reverting the change.
Fixes: 5942ddbc500d ("mtd: introduce mtd_block_markbad interface") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cyrille Pitchen [Wed, 3 Feb 2016 13:26:46 +0000 (14:26 +0100)]
mtd: spi-nor: remove micron_quad_enable()
This patch remove the micron_quad_enable() function which force the Quad
SPI mode. However, once this mode is enabled, the Micron memory expect ALL
commands to use the SPI 4-4-4 protocol. Hence a failure does occur when
calling spi_nor_wait_till_ready() right after the update of the Enhanced
Volatile Configuration Register (EVCR) in the micron_quad_enable() as
the SPI controller driver is not aware about the protocol change.
Since there is almost no performance increase using Fast Read 4-4-4
commands instead of Fast Read 1-1-4 commands, we rather keep on using the
Extended SPI mode than enabling the Quad SPI mode.
Let's take the example of the pretty standard use of 8 dummy cycles during
Fast Read operations on 64KB erase sectors:
Fast Read 1-1-4 requires 8 cycles for the command, then 24 cycles for the
3byte address followed by 8 dummy clock cycles and finally 65536*2 cycles
for the read data; so 131112 clock cycles.
On the other hand the Fast Read 4-4-4 would require 2 cycles for the
command, then 6 cycles for the 3byte address followed by 8 dummy clock
cycles and finally 65536*2 cycles for the read data. So 131088 clock
cycles. The theorical bandwidth increase is 0.0%.
Now using Fast Read operations on 512byte pages:
Fast Read 1-1-4 needs 8+24+8+(512*2) = 1064 clock cycles whereas Fast
Read 4-4-4 would requires 2+6+8+(512*2) = 1040 clock cycles. Hence the
theorical bandwidth increase is 2.3%.
Consecutive reads for non sequential pages is not a relevant use case so
The Quad SPI mode is not worth it.
mtd_speedtest seems to confirm these figures.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Fixes: 548cd3ab54da ("mtd: spi-nor: Add quad I/O support for Micron SPI NOR") Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Thomas Petazzoni [Wed, 10 Feb 2016 13:54:21 +0000 (14:54 +0100)]
mtd: nand: pxa3xx_nand: add support for partial chunks
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.
When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.
When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:
| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |
So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.
When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:
| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |
So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.
Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.
To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.
In order to implement reading of the last chunk, this commit:
- Adds a number of new fields to the pxa3xx_nand_info to describe how
many full chunks and how many chunks we have, the size of full
chunks and partial chunks, both in terms of data area and spare
area.
- Fills in the step_chunk_size and step_spare_size variables to
describe how much data and spare should be read/written for the
current read/program step.
- Reworks the state machine to accommodate doing the additional read
or program step when a last partial chunk is used.
This commit has been tested on a Marvell Armada 398 DB board, with a
4KB page NAND, tested in both 4 bits ECC and 8 bits ECC
configurations. Robert Jarzmik has tested on some PXA platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Linus Walleij [Mon, 1 Feb 2016 22:02:48 +0000 (23:02 +0100)]
mtd: map: fix .set_vpp() documentation
As of commit 876fe76d793d03077eb61ba3afab4a383f46c554
"mtd: maps: physmap: Add reference counter to set_vpp()"
the comment in the header file is incorrect and misleading.
Fix it up.
Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Parsons <lost.distance@yahoo.com> Fixes: 876fe76d793d ("mtd: maps: physmap: Add reference counter to set_vpp()") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Simon Arlott [Sun, 13 Dec 2015 22:49:26 +0000 (22:49 +0000)]
mtd: bcm63xxpart: Remove dependency on mach-bcm63xx
Read nvram directly from flash instead of using the in-memory copy that
mach-bcm63xx has, to remove the dependency on mach-bcm63xx and allow the
parser to work on bmips too.
Rename remaining BCM63XX defines to BCM963XX as these are properties of
the flash layout on the board.
BCM963XX_DEFAULT_PSI_SIZE changes from SZ_64K to 64 because it will be
multiplied by SZ_1K later on.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Romain Izard [Wed, 10 Feb 2016 09:56:26 +0000 (10:56 +0100)]
mtd: atmel_nand: Support 32-bit ECC strength
As the SAMA5D2 controller supports the 32-bit ECC strength, accept it
as a valid setting when required by the device tree or the NAND
parameter page.
Then configure the controller to use this new setting.
For the binding: Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Romain Izard [Wed, 10 Feb 2016 09:56:25 +0000 (10:56 +0100)]
mtd: atmel_nand: Support PMECC on SAMA5D2
Starting with the SAMA5D2, there is a new revision of the Atmel PMECC
controller that can correct 32 bits in each sector. This controller is
not 100% compatible with the previous revision that corrected a maximum
of 24 bits by sector, as some register addresses overlap.
Using information from the device tree, we can configure the driver to
work with both versions.
For the binding: Acked-by: Rob Herring <robh@kernel.org> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Romain Izard [Wed, 10 Feb 2016 09:56:23 +0000 (10:56 +0100)]
mtd: atmel_nand: Support variable RB_EDGE interrupts
The NFC controller used to accelerate the NAND transfers on SAMA5 chips
can use either RB_EDGE0 or RB_EDGE3 as its ready/busy interrupt bit.
Use the controller's compatible string to select the correct bit.
For the binding: Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Wenyou Yang <Wenyou.yang@atmel.com> Tested-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NAND core layer is already taking care of ecclayout propagation. Remove
this useless assignment.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON [Mon, 7 Dec 2015 22:26:00 +0000 (23:26 +0100)]
mtd: nand: jz4740: kill the ->ecc_layout field
->ecc_layout is not used by any board file. Kill this field to avoid any
confusion. New boards are encouraged to use the default ECC layout defined
in NAND core.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Boris BREZILLON [Mon, 7 Dec 2015 22:25:59 +0000 (23:25 +0100)]
mtd: nand: s3c2410: kill the ->ecc_layout field
The s3c2410 is allowing board data to overload the default ECC layout
defined inside the driver, but this feature is not used by board
specific definitions.
Kill this field so that we can easily move to a model where ecclayout
are dynamically allocated by the NAND controller driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Linus Torvalds [Sun, 24 Jan 2016 20:50:56 +0000 (12:50 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
Linus Torvalds [Sun, 24 Jan 2016 20:45:35 +0000 (12:45 -0800)]
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Emergency travel prevented me from completing my final testing on this
until today. Nothing here that couldn't wait until RC1 fixes, but I
thought it best to get it out sooner rather than later as it does
contain a build warning fix.
Summary:
A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:
ideapad-laptop:
- Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS:
- Combine multiple telemetry entries
intel_telemetry_debugfs:
- Fix unused warnings in telemetry debugfs"
* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS: Combine multiple telemetry entries
intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
Linus Torvalds [Sun, 24 Jan 2016 20:43:06 +0000 (12:43 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
Linus Torvalds [Sun, 24 Jan 2016 20:39:09 +0000 (12:39 -0800)]
Merge tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p updates from Eric Van Hensbergen:
"Sorry for the last minute pull request, there's was a change that
didn't get pulled into for-next until two weeks ago and I wanted to
give it some bake time.
Summary:
Rework and error handling fixes, primarily in the fscatch and fd
transports"
* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: use fscache mutex rather than spinlock
9p: trans_fd, bail out if recv fcall if missing
9p: trans_fd, read rework to use p9_parse_header
net/9p: Add device name details on error
Linus Torvalds [Sun, 24 Jan 2016 20:34:13 +0000 (12:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
Linus Torvalds [Sun, 24 Jan 2016 20:31:12 +0000 (12:31 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull SMB3 fixes from Steve French:
"A collection of CIFS/SMB3 fixes.
It includes a couple bug fixes, a few for improved debugging of
cifs.ko and some improvements to the way cifs does key generation.
I do have some additional bug fixes I expect in the next week or two
(to address a problem found by xfstest, and some fixes for SMB3.11
dialect, and a couple patches that just came in yesterday that I am
reviewing)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
cifs: fix race between call_async() and reconnect()
Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
cifs: Allow using O_DIRECT with cache=loose
cifs: Make echo interval tunable
cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
Print IP address of unresponsive server
cifs: Ratelimit kernel log messages
Josh Boyer [Sun, 24 Jan 2016 15:46:42 +0000 (10:46 -0500)]
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
If we detect that there is nothing to do just set the flag and do not
check if it was already set before. Races really do not matter. If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.
Since commit 0eb77e988032 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd. This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up. The VM_BUG_ON is therefore misleading and no more
appropriate. Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly. Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alban Bedel [Thu, 10 Dec 2015 09:57:20 +0000 (10:57 +0100)]
MIPS: zboot: Avoid useless rebuilds
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr> Cc: linux-mips@linux-mips.org Cc: Alex Smith <alex.smith@imgtec.com> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:47:55 +0000 (22:47 +0000)]
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.
Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:45:30 +0000 (22:45 +0000)]
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.
Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Sun, 24 Jan 2016 02:45:06 +0000 (18:45 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
James Hogan [Wed, 16 Dec 2015 23:49:38 +0000 (23:49 +0000)]
MIPS: Move KVM specific opcodes into asm/inst.h
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b943
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
James Hogan [Wed, 16 Dec 2015 23:49:37 +0000 (23:49 +0000)]
MIPS: KVM: Use cacheops.h definitions
Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.
James Hogan [Wed, 16 Dec 2015 23:49:36 +0000 (23:49 +0000)]
MIPS: Break down cacheops.h definitions
Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.
To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.
James Hogan [Wed, 16 Dec 2015 23:49:34 +0000 (23:49 +0000)]
MIPS: Update trap codes
Add a few missing trap codes.
[ralf@linux-mips.org: Drop removal of exception codes. I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
James Hogan [Wed, 16 Dec 2015 23:49:33 +0000 (23:49 +0000)]
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
James Hogan [Wed, 16 Dec 2015 23:49:31 +0000 (23:49 +0000)]
MIPS: KVM: Refactor added offsetof()s
When calculating the offsets into the commpage for dynamically
translated mtc0/mfc0 guest instructions, multiple offsetof()s are added
together to find the offset of the specific register in the mips_coproc,
within the commpage.
Simplify each of these cases to a single offsetof() to find the offset
of the specific register within the commpage.
James Hogan [Wed, 16 Dec 2015 23:49:28 +0000 (23:49 +0000)]
MIPS: Move definition of DC bit to mipsregs.h
The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.
Lets reunite the DC bit definitions with its friends in mipsregs.h.
James Hogan [Wed, 16 Dec 2015 23:49:27 +0000 (23:49 +0000)]
MIPS: KVM: Drop some unused definitions from kvm_host.h
Some definitions in the MIPS asm/kvm_host.h are completely unused, so
lets drop them.
MS_TO_NS is no longer used since commit e30492bbe95a ("MIPS: KVM:
Rewrite count/compare timer emulation"). The others don't appear ever to
have been used.
Joshua Henderson [Thu, 14 Jan 2016 01:15:39 +0000 (18:15 -0700)]
MIPS: Add support for PIC32MZDA platform
This adds support for the Microchip PIC32 MIPS microcontroller with the
specific variant PIC32MZDA. PIC32MZDA is based on the MIPS m14KEc core
and boots using device tree.
This includes an early pin setup and early clock setup needed prior to
device tree being initialized. In additon, an interface is provided to
synchronize access to registers shared across several peripherals.
Cristian Birsan [Thu, 14 Jan 2016 01:15:35 +0000 (18:15 -0700)]
IRQCHIP: irq-pic32-evic: Add support for PIC32 interrupt controller
This adds support for the interrupt controller present on PIC32 class
devices. It handles all internal and external interrupts. This controller
exists outside of the CPU core and is the arbitrator of all interrupts
(including interrupts from the CPU itself) before they are presented to
the CPU.
The following features are supported:
- DT properties for EVIC and for devices/peripherals that use interrupt lines
- Persistent and non-persistent interrupt handling
- irqdomain and generic chip support
- Configuration of external interrupt edge polarity
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com> Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12092/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Tue, 22 Dec 2015 13:56:39 +0000 (13:56 +0000)]
MIPS: ptrace: Drop cp0_tcstatus from regoffset_table[]
The cp0_tcstatus member of struct pt_regs was removed along with the
rest of SMTC in v3.16, commit b633648c5ad3 ("MIPS: MT: Remove SMTC
support"), however recent uprobes support in v4.3 added back a reference
to it in the regoffset_table[] in ptrace.c. Remove it.
Linus Walleij [Tue, 22 Dec 2015 14:41:44 +0000 (15:41 +0100)]
MIPS: TXx9: iocled: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:41:19 +0000 (15:41 +0100)]
MIPS: RB532: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:41:01 +0000 (15:41 +0100)]
MIPS: TXx9: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:40:27 +0000 (15:40 +0100)]
MIPS: ar7: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Linus Walleij [Tue, 22 Dec 2015 14:40:02 +0000 (15:40 +0100)]
MIPS: Alchemy: Be sure to clamp return value
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
projects / mirror_ubuntu-hirsute-kernel.git / log