Hans de Goede [Sat, 5 Dec 2020 15:02:01 +0000 (16:02 +0100)]
Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers
With the recent btusb change to detect and deal with more fake CSR
controllers, I decided to see if fake CSR controllers with Barrot 8041a02 chips would now work.
After much experimentation I came to the conclusion that it works, if I
have autosuspend enabled initially and then disable it after the device
has suspended at least once. Yes this is very weird, but I've tried many
things, like manually clearing the remote-wakeup feature. Doing a
runtime-resume + runtime suspend is the only way to get the receiver
to actually report received data (and/or pairing info) through its
bulk rx endpoint.
But the funkyness of the bulk-endpoint does not stop there, I mainly
found out about this problem, because with autosuspend enabled
(which usually ensures the suspend at least once condition is met),
the receiver stops reporting received data through its bulk rx endpoint
as soon as autosuspend kicks in. So I initially just disabled
autosuspend, but then the receiver does not work at all.
This was with a fake CSR receiver with a Barrot 8041a02 chip with a
bcdDevice value of 0x8891, a lmp_subver of 0x1012, a hci_rev of 0x0810
and a hci_ver of BLUETOOTH_VER_4_0.
Summarizing this specific fake CSR receiver has the following 2 issues:
1. The bulk rx endpoint will never report any data unless
the device was suspended at least once.
2. They will not wakeup when autosuspended and receiving data on their
bulk rx endpoint from e.g. a keyboard or mouse (IOW remote-wakeup support
is broken for the bulk endpoint).
Add a workaround for 1. which enables runtime-suspend, force-suspends
the hci and then wakes-it up by disabling runtime-suspend again.
Add a workaround for 2. which clears the hci's can_wake flag, this way
the hci will still be autosuspended when it is not open.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Hans de Goede [Sat, 5 Dec 2020 15:02:00 +0000 (16:02 +0100)]
Bluetooth: btusb: Fix detection of some fake CSR controllers with a bcdDevice val of 0x0134
Commit cde1a8a99287 ("Bluetooth: btusb: Fix and detect most of the
Chinese Bluetooth controllers") made the detection of fake controllers
more generic fixing it for much of the newer fakes / clones.
But this does not work for a fake CSR controller with a bcdDevice
value of 0x0134, which was correctly identified as fake before
this change.
Add an extra check for this special case, checking for a combination
of a bcdDevice value of 0x0134, together with a lmp_subver of 0x0c5c
and a hci_ver of BLUETOOTH_VER_2_0.
The chip inside this fake dongle is marked as with "clockwise cw6629d".
Fixes: cde1a8a99287 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Daniel Winkler [Thu, 3 Dec 2020 20:12:52 +0000 (12:12 -0800)]
Bluetooth: Change MGMT security info CMD to be more generic
For advertising, we wish to know the LE tx power capabilities of the
controller in userspace, so this patch edits the Security Info MGMT
command to be more generic, such that other various controller
capabilities can be included in the EIR data. This change also includes
the LE min and max tx power into this newly-named command.
The change was tested by manually verifying that the MGMT command
returns the tx power range as expected in userspace.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Daniel Winkler [Thu, 3 Dec 2020 20:12:51 +0000 (12:12 -0800)]
Bluetooth: Query LE tx power on startup
Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.
This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Daniel Winkler [Thu, 3 Dec 2020 20:12:50 +0000 (12:12 -0800)]
Bluetooth: Use intervals and tx power from mgmt cmds
This patch takes the min/max intervals and tx power optionally provided
in mgmt interface, stores them in the advertisement struct, and uses
them when configuring the hci requests. While tx power is not used if
extended advertising is unavailable, software rotation will use the min
and max advertising intervals specified by the client.
This change is validated manually by ensuring the min/max intervals are
propagated to the controller on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks, and that tx power is
propagated correctly on hatch. These tests are performed with multiple
advertisements simultaneously.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Daniel Winkler [Thu, 3 Dec 2020 20:12:49 +0000 (12:12 -0800)]
Bluetooth: Break add adv into two mgmt commands
This patch adds support for the new advertising add interface, with the
first command setting advertising parameters and the second to set
advertising data. The set parameters command allows the caller to leave
some fields "unset", with a params bitfield defining which params were
purposefully set. Unset parameters will be given defaults when calling
hci_add_adv_instance. The data passed to the param mgmt command is
allowed to be flexible, so in the future if bluetoothd passes a larger
structure with new params, the mgmt command will ignore the unknown
members at the end.
This change has been validated on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks running bluetoothd that
support this new interface. I ran the following manual tests:
- Set several (3) advertisements using modified test_advertisement.py
- For each, validate correct data and parameters in btmon trace
- Verified both for software rotation and extended adv
Automatic test suite also run, testing many (25) scenarios of single and
multi-advertising for data/parameter correctness.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Daniel Winkler [Thu, 3 Dec 2020 20:12:48 +0000 (12:12 -0800)]
Bluetooth: Add helper to set adv data
We wish to handle advertising data separately from advertising
parameters in our new MGMT requests. This change adds a helper that
allows the advertising data and scan response to be updated for an
existing advertising instance.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Kiran K [Thu, 19 Nov 2020 11:39:40 +0000 (17:09 +0530)]
Bluetooth: btusb: Add *setup* function for new generation Intel controllers
Define a new *setup* function for new generation Intel controllers
Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Amit K Bag <amit.k.bag@intel.com> Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com> Reviewed-by: Sathish Narasimman <Sathish.Narasimman@intel.com> Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com> Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Howard Chung [Thu, 26 Nov 2020 04:22:23 +0000 (12:22 +0800)]
Bluetooth: Handle active scan case
This patch adds code to handle the active scan during interleave
scan. The interleave scan will be canceled when users start active scan,
and it will be restarted after active scan stopped.
Signed-off-by: Howard Chung <howardchung@google.com> Reviewed-by: Alain Michaud <alainm@chromium.org> Reviewed-by: Manish Mandlik <mmandlik@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Howard Chung [Thu, 26 Nov 2020 04:22:22 +0000 (12:22 +0800)]
Bluetooth: Handle system suspend resume case
This patch adds code to handle the system suspension during interleave
scan. The interleave scan will be canceled when the system is going to
sleep, and will be restarted after waking up.
Howard Chung [Thu, 26 Nov 2020 04:22:21 +0000 (12:22 +0800)]
Bluetooth: Interleave with allowlist scan
This patch implements the interleaving between allowlist scan and
no-filter scan. It'll be used to save power when at least one monitor is
registered and at least one pending connection or one device to be
scanned for.
The durations of the allowlist scan and the no-filter scan are
controlled by MGMT command: Set Default System Configuration. The
default values are set randomly for now.
Signed-off-by: Howard Chung <howardchung@google.com> Reviewed-by: Alain Michaud <alainm@chromium.org> Reviewed-by: Manish Mandlik <mmandlik@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Edward Vear [Tue, 27 Oct 2020 07:02:03 +0000 (00:02 -0700)]
Bluetooth: Fix attempting to set RPA timeout when unsupported
During controller initialization, an LE Set RPA Timeout command is sent
to the controller if supported. However, the value checked to determine
if the command is supported is incorrect. Page 1921 of the Bluetooth
Core Spec v5.2 shows that bit 2 of octet 35 of the Supported_Commands
field corresponds to the LE Set RPA Timeout command, but currently
bit 6 of octet 35 is checked. This patch checks the correct value
instead.
This issue led to the error seen in the following btmon output during
initialization of an adapter (rtl8761b) and prevented initialization
from completing.
< HCI Command: LE Set Resolvable Private Address Timeout (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Complete (0x0e) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 2
Status: Unsupported Remote Feature / Unsupported LMP Feature (0x1a)
= Close Index: 00:E0:4C:6B:E5:03
The error did not appear when running with this patch.
Signed-off-by: Edward Vear <edwardvear@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Bluetooth: Fix not sending Set Extended Scan Response
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Jimmy Wahlberg [Mon, 16 Nov 2020 15:56:26 +0000 (16:56 +0100)]
Bluetooth: Fix for Bluetooth SIG test L2CAP/COS/CFD/BV-14-C
This test case is meant to verify that multiple
unknown options is included in the response.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part A
page 1057
'On an unknown option failure (Result=0x0003),
the option(s) that contain anoption type field that is not
understood by the recipient of the L2CAP_CONFIGURATION_REQ
packet shall be included in the L2CAP_CONFIGURATION_RSP
packet unless they are hints.'
Signed-off-by: Jimmy Wahlberg <jimmywa@spotify.com> Reviewed-by: Luiz Augusto Von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Hans de Goede [Sun, 22 Nov 2020 12:17:25 +0000 (13:17 +0100)]
Bluetooth: revert: hci_h5: close serdev device and free hu in h5_close
There have been multiple revisions of the patch fix the h5->rx_skb
leak. Accidentally the first revision (which is buggy) and v5 have
both been merged:
v1 commit 70f259a3f427 ("Bluetooth: hci_h5: close serdev device and free
hu in h5_close");
v5 commit 855af2d74c87 ("Bluetooth: hci_h5: fix memory leak in h5_close")
The correct v5 makes changes slightly higher up in the h5_close()
function, which allowed both versions to get merged without conflict.
The changes from v1 unconditionally frees the h5 data struct, this
is wrong because in the serdev enumeration case the memory is
allocated in h5_serdev_probe() like this:
h5 = devm_kzalloc(dev, sizeof(*h5), GFP_KERNEL);
So its lifetime is tied to the lifetime of the driver being bound
to the serdev and it is automatically freed when the driver gets
unbound. In the serdev case the same h5 struct is re-used over
h5_close() and h5_open() calls and thus MUST not be free-ed in
h5_close().
The serdev_device_close() added to h5_close() is incorrect in the
same way, serdev_device_close() is called on driver unbound too and
also MUST no be called from h5_close().
This reverts the changes made by merging v1 of the patch, so that
just the changes of the correct v5 remain.
Cc: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: hci_qca: Wait for timeout during suspend
Currently qca_suspend() is relied on IBS mechanism. During
FW download and memory dump collections, IBS will be disabled.
In those cases, driver will allow suspend and still uses the
serdev port, which results to errors. Now added a wait timeout
if suspend is triggered during FW download and memory collections.
Currently the check for a failed bt_skb_alloc allocation is incorrectly
checking using IS_ERR and this can lead to a null pointer dereference. Fix
this by checking for a null pointer return using the !skb idiom.
Addresses-Coverity: ("Dereference null return") Fixes: 1996d9cad6ad ("Bluetooth: btrtl: Ask 8821C to drop old firmware") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Xiaolei Wang [Tue, 10 Nov 2020 10:13:11 +0000 (18:13 +0800)]
Bluetooth: hci_ll: add a small delay for wl1271 enable bt_en
When using the wl1271 Bluetooth function of am335x, it is found that the
Bluetooth module cannot respond in time after Bluetooth is enabled, and
a small delay is needed to work normally, so whether to add a small
mdelay.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Julian Pidancet [Mon, 9 Nov 2020 16:47:22 +0000 (17:47 +0100)]
Bluetooth: btusb: Add support for 1358:c123 Realtek 8822CE device
Huawei Matebook 13 2020 AMD laptops (and probably other Matebook models)
are equiped with a RTL8822CE chip using the 1358:c123 USB identifiers.
This patch adds firmware loading support for it.
Nigel Christian [Wed, 11 Nov 2020 04:55:38 +0000 (23:55 -0500)]
Bluetooth: hci_qca: resolve various warnings
Replace symbolic permissions with octal values. Use usleep_range
for small msec values due to the fact that msleep() less than
20ms may have unexpected behavior/sleep longer.
Bluetooth: hci_qca: Enhance retry logic in qca_setup
Currently driver only retries to download FW if FW downloading
is failed. Sometimes observed command timeout for version request
command, if this happen on some platforms during boot time, then
a reboot is needed to turn ON BT. Instead to avoid a reboot, now
extended retry logic for version request command too.
Archie Pusaka [Wed, 11 Nov 2020 06:32:20 +0000 (14:32 +0800)]
Bluetooth: Enforce key size of 16 bytes on FIPS level
According to the spec Ver 5.2, Vol 3, Part C, Sec 5.2.2.8:
Device in security mode 4 level 4 shall enforce:
128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms (E0 not allowed, SAFER+ not allowed,
and P-192 not allowed; encryption key not shortened)
This patch rejects connection with key size below 16 for FIPS
level services.
Bluetooth: hidp: use correct wait queue when removing ctrl_wait
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and dead000000000200 is LIST_POISON2.
Bluetooth: Move force_bredr_smp debugfs into hci_debugfs_create_bredr
Avoid multiple attempts to create the debugfs entry, force_bredr_smp,
by moving it from the SMP registration to the BR/EDR controller init
section. hci_debugfs_create_bredr is only called when HCI_SETUP and
HCI_CONFIG is not set.
Signed-off-by: Claire Chang <tientzu@chromium.org> Reviewed-by: Alain Michaud <alainm@chromium.org> Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix: LL PRivacy BLE device fails to connect
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
Kai-Heng Feng [Mon, 26 Oct 2020 08:28:38 +0000 (16:28 +0800)]
Bluetooth: btrtl: Ask 8821C to drop old firmware
Some platforms keep USB power even when they are powered off and in S5,
this makes Realtek 8821C keep its firmware even after a cold boot, and
make 8821C never load new firmware.
So use vendor specific HCI command to ask 8821C drop its firmware after
system shutdown.
Newer firmware doesn't have this issue so we only use this trick for old
8821C firmware version.
Max Chou [Wed, 4 Nov 2020 12:04:14 +0000 (20:04 +0800)]
Bluetooth: btrtl: Refine the ic_id_table for clearer and more regular
Enhance the ic_id_table that it's able to maintain regularly.
To judge which chip should be initialized by LMP subversion, HCI revision,
HCI version and HCI bus which were given in the ic_id_table.
Also, refine the incorrect LMP subversion of ROM for RTL8723D and
RTL8723A.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn> Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Daniel Winkler [Fri, 6 Nov 2020 23:20:19 +0000 (15:20 -0800)]
Bluetooth: Resume advertising after LE connection
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Peilin Ye [Wed, 9 Sep 2020 07:17:00 +0000 (03:17 -0400)]
Bluetooth: Fix slab-out-of-bounds read in hci_le_direct_adv_report_evt()
`num_reports` is not being properly checked. A malformed event packet with
a large `num_reports` number makes hci_le_direct_adv_report_evt() read out
of bounds. Fix it.
Cc: stable@vger.kernel.org Fixes: 2f010b55884e ("Bluetooth: Add support for handling LE Direct Advertising Report events") Reported-and-tested-by: syzbot+24ebd650e20bd263ca01@syzkaller.appspotmail.com Link: https://syzkaller.appspot.com/bug?extid=24ebd650e20bd263ca01 Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: hci_h5: close serdev device and free hu in h5_close
When h5_close() gets called, the memory allocated for the hu gets
freed only if hu->serdev doesn't exist. This leads to a memory leak.
So when h5_close() is requested, close the serdev device instance and
free the memory allocated to the hu entirely instead.
Bluetooth: Fix null pointer dereference in hci_event_packet()
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
The goal of this series is to more tightly control when GSI
interrupts are enabled. This is a long-ish series, so I'll
describe it in parts.
The first patch is actually unrelated... I forgot to include
it in my previous series (which exposed the GSI layer to the
IPA version). It is a trivial comments-only update patch.
The second patch defers registering the GSI interrupt handler
until *after* all of the resources that handler touches have
been initialized. In practice, we don't see this interrupt
that early, but this precludes an obvious problem.
The next two patches are simple changes. The first just
trivially renames a field. The second switches from using
constant mask values to using an enumerated type of bit
positions to represent each GSI interrupt type.
The rest implement the "real work." First, all interrupts
are disabled at initialization time. Next, we keep track of
a bitmask of enabled GSI interrupt types, updating it each
time we enable or disable one of them. From there we have
a set of patches that one-by-one enable each interrupt type
only during the period it is required. This includes allowing
a channel to generate IEOB interrupts only when it has been
enabled. And finally, the last patch simplifies some code
now that all GSI interrupt types are handled uniformly.
====================
Alex Elder [Thu, 5 Nov 2020 18:14:07 +0000 (12:14 -0600)]
net: ipa: pass a value to gsi_irq_type_update()
Now that all of the GSI interrupts are handled uniformly,
change gsi_irq_type_update() so it takes a value. Have the
function assign that value to the cached mask of enabled GSI
IRQ types before writing it to hardware.
Note that gsi_irq_teardown() will only be called after
gsi_irq_disable(), so it's not necessary for the former
to disable all IRQ types. Get rid of that.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:06 +0000 (12:14 -0600)]
net: ipa: only enable GSI general IRQs when needed
Most GSI general errors are unrecoverable without a full reset.
Despite that, we want to receive these errors so we can at least
report what happened before whatever undefined behavior ensues.
Explicitly disable all such interrupts in gsi_irq_setup(), then
enable those we want in gsi_irq_enable(). List the interrupt types
we are interested in (everything but breakpoint) explicitly rather
than using GSI_CNTXT_GSI_IRQ_ALL, and remove that symbol's
definition.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:05 +0000 (12:14 -0600)]
net: ipa: explicitly disallow inter-EE interrupts
It is possible for other execution environments (EEs, like the modem)
to request changes to local (AP) channel or event ring state. We do
not support this feature.
In gsi_irq_setup(), explicitly zero the mask that defines which
channels are permitted to generate inter-EE channel state change
interrupts. Do the same for the event ring mask.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:04 +0000 (12:14 -0600)]
net: ipa: only enable GSI IEOB IRQs when needed
A GSI channel must be started in order to use it to perform a
transfer data (or command) transaction. And the only time we'll see
an IEOB interrupt is if we send a transaction to a started channel.
Therefore we do not need to have the IEOB interrupt type enabled
until at least one channel has been started. And once the last
started channel has been stopped, we can disable the IEOB interrupt
type again.
We already enable the IEOB interrupt for a particular channel only
when it is started. Extend that by having the IEOB interrupt *type*
be enabled only when at least one channel is in STARTED state.
Disallow all channels from triggering the IEOB interrupt in
gsi_irq_setup(). We only enable an channel's interrupt when
needed, so there is no longer any need to zero the channel mask
in gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:03 +0000 (12:14 -0600)]
net: ipa: only enable generic command completion IRQ when needed
The completion of a generic EE GSI command is signaled by a global
interrupt of type GP_INT1. The only other used type for a global
interrupt is a hardware error report.
First, disallow all global interrupt types in gsi_irq_setup(). We
want to know about hardware errors, so re-enable the interrupt type
in gsi_irq_enable(), to allow hardware errors to be reported.
Disable that interrupt type again in gsi_irq_disable().
We only issue generic EE commands one at a time, and there's no
reason to keep the completion interrupt enabled when no generic
EE command is pending. We furthermore have no need to enable the
GP_INT2 or GP_INT3 interrupt types (which aren't used).
The change in gsi_irq_enable() makes GSI_CNTXT_GLOB_IRQ_ALL unused,
so get rid of it. Have gsi_generic_command() enable the GP_INT1
interrupt type (in addition to the ERROR_INT type) only while a
generic command is pending.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:02 +0000 (12:14 -0600)]
net: ipa: only enable GSI event control IRQs when needed
A GSI event ring causes an event control interrupt to fire whenever
its state changes (between NOT_ALLOCATED and ALLOCATED). No event
ring should ever change state except when we request it to.
Currently, we permit *all* events rings to generate event control
interrupts--even those that are never used. And we enable event
control interrupts essentially at all times, from setup to teardown.
Instead, only enable the event control interrupt type for the
duration of an event ring command, and when doing so, only allow
the event ring being operated upon to cause the interrupt to fire.
Disallow all event rings from issuing the event control interrupt
in gsi_irq_setup().
Because an event ring's interrupt is only enabled when needed,
there is no longer any need to zero the event channel mask in
gsi_irq_disable().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:01 +0000 (12:14 -0600)]
net: ipa: only enable GSI channel control IRQs when needed
A GSI channel causes a channel control interrupt to fire whenever
its state changes (between NOT_ALLOCATED, ALLOCATED, STARTED, etc.).
We do not support inter-EE channel commands (initiated by other EEs),
so no channel should ever change state except when we request it to.
Currently, we permit *all* channels to generate channel control
interrupts--even those that are never used. And we enable channel
control interrupts essentially at all times, from setup to teardown.
Instead, disable all channel control interrupts initially in
gsi_irq_setup(), and only enable the channel control interrupt
type for the duration of a channel command. When doing so, only
allow the channel being operated upon to cause the interrupt to
fire.
Because a channel's interrupt is now enabled only when needed (one
channel at a time), there is no longer any need to zero the channel
mask in gsi_irq_disable().
Add new gsi_irq_type_enable() and gsi_irq_type_disable() as helper
functions to control whether a given GSI interrupt type is enabled.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:14:00 +0000 (12:14 -0600)]
net: ipa: cache last-saved GSI IRQ enabled type
Keep track of the set of GSI interrupt types that are currently
enabled by recording the mask value to write (or last written) to
the TYPE_IRQ_MSK register.
Create a new helper function gsi_irq_type_update() to handle
actually writing the register.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:13:59 +0000 (12:13 -0600)]
net: ipa: disable all GSI interrupt types initially
Introduce gsi_irq_setup() and gsi_irq_teardown() to disable all
GSI interrupts when first setting up GSI hardware, and to clean
things up when we're done.
Re-enable all GSI interrupt types in gsi_irq_enable(), but do
so only after each of the type-specific interrupt masks has
been configured. Similarly, disable all interrupt types in
gsi_irq_disable()--first--before zeroing out the type-specific
masks.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:13:58 +0000 (12:13 -0600)]
net: ipa: define GSI interrupt types with an enum
Define the GSI interrupt types with an enumerated type whose values
are the bit positions representing each interrupt type. Include a
short comment describing how each interrupt type is used.
Build up the enabled interrupt mask explicitly in gsi_irq_enable(),
and get rid of the definition of GSI_CNTXT_TYPE_IRQ_MSK_ALL.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:13:57 +0000 (12:13 -0600)]
net: ipa: rename gsi->event_enable_bitmap
Rename the "event_enable_bitmap" field of the GSI structure to be
"ieob_enabled_bitmap". An upcoming patch will cache the last value
stored for another interrupt mask and this is a more direct naming
convention to follow.
Add a few comments to explain the bitmap fields in the GSI structure.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Thu, 5 Nov 2020 18:13:56 +0000 (12:13 -0600)]
net: ipa: request GSI IRQ later
Introduce gsi_irq_init() and gsi_irq_exit(), to encapsulate looking
up the GSI IRQ and registering its handler. Call gsi_irq_init() a
little later in gsi_init(), and initialize the completion earlier.
The IRQ handler accesses both the GSI virtual memory pointer and the
completion, and this way these things will have been initialized
before the gsi_irq() can ever be called.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xie He [Thu, 5 Nov 2020 07:34:34 +0000 (23:34 -0800)]
net: x25_asy: Delete the x25_asy driver
This driver transports LAPB (X.25 link layer) frames over TTY links.
I can safely say that this driver has no actual user because it was
not working at all until:
commit 8fdcabeac398 ("drivers/net/wan/x25_asy: Fix to make it work")
The code in its current state still has problems:
1.
The uses of "struct x25_asy" in x25_asy_unesc (when receiving) and in
x25_asy_write_wakeup (when sending) are not protected by locks against
x25_asy_change_mtu's changing of the transmitting/receiving buffers.
Also, all "netif_running" checks in this driver are not protected by
locks against the ndo_stop function.
2.
The driver stops all TTY read/write when the netif is down.
I think this is not right because this may cause the last outgoing frame
before the netif goes down to be incompletely transmitted, and the first
incoming frame after the netif goes up to be incompletely received.
And there may also be other problems.
I was planning to fix these problems but after recent discussions about
deleting other old networking code, I think we may just delete this
driver, too.
Kaixu Xia [Wed, 4 Nov 2020 05:24:04 +0000 (13:24 +0800)]
cxgb4: Fix the -Wmisleading-indentation warning
Fix the gcc warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
This patchset dynamically enable MDIO interface. The background for this
change is coming from Cadence GEM controller(macb) in which MDC is active
only during MDIO read or write operations while the PHY registers are
read or written. It is implemented as an IP feature.
For axiethernet as dynamic MDC enable/disable is not supported in hw
we are implementing it in sw. This change doesn't affect any existing
functionality.
====================
Clayton Rayment [Tue, 3 Nov 2020 11:26:10 +0000 (16:56 +0530)]
net: xilinx: axiethernet: Enable dynamic MDIO MDC
MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.
net: xilinx: axiethernet: Introduce helper functions for MDC enable/disable
Introduce helper functions to enable/disable MDIO interface clock. This
change serves a preparatory patch for the coming feature to dynamically
control the management bus clock.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
net: convert tasklets to use new tasklet_setup API
Commit 12cc923f1ccc ("tasklet: Introduce new initialization API")'
introduced a new tasklet initialization API. This series converts
all the net/* drivers to use the new tasklet_setup() API
The following series is based on net-next (9faebeb2d)
v3:
introduce qdisc_from_priv, suggested by Eric Dumazet.
v2:
get rid of QDISC_ALIGN()
v1:
fix kerneldoc
====================
Allen Pais [Tue, 3 Nov 2020 09:18:23 +0000 (14:48 +0530)]
net: xfrm: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:22 +0000 (14:48 +0530)]
net: smc: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:21 +0000 (14:48 +0530)]
net: sched: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:19 +0000 (14:48 +0530)]
net: mac802154: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:18 +0000 (14:48 +0530)]
net: mac80211: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:17 +0000 (14:48 +0530)]
net: ipv4: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allen Pais [Tue, 3 Nov 2020 09:18:16 +0000 (14:48 +0530)]
net: dccp: convert tasklets to use new tasklet_setup() API
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dany Madden [Fri, 6 Nov 2020 19:17:45 +0000 (14:17 -0500)]
Revert ibmvnic merge do_change_param_reset into do_reset
This reverts commit 16b5f5ce351f8709a6b518cc3cbf240c378305bf
where it restructures do_reset. There are patches being tested that
would require major rework if this is committed first.
We will resend this after the other patches have been applied.
Linus Torvalds [Fri, 6 Nov 2020 21:08:25 +0000 (13:08 -0800)]
Merge branch 'mtd/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal.
* 'mtd/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: stm32_fmc2: fix broken ECC
mtd: spi-nor: Fix address width on flash chips > 16MB
mtd: spi-nor: Don't copy self-pointing struct around
mtd: rawnand: ifc: Move the ECC engine initialization to the right place
mtd: rawnand: mxc: Move the ECC engine initialization to the right place
Linus Torvalds [Fri, 6 Nov 2020 21:05:21 +0000 (13:05 -0800)]
Merge tag 'spi-fix-v5.10-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"This is an additional fix on top of 5e31ba0c0543 ('spi: bcm2835: fix
gpio cs level inversion') - when sending my prior pull request I had
misremembred the status of that patch, apologies for the noise here"
* tag 'spi-fix-v5.10-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm2835: remove use of uninitialized gpio flags variable
Linus Torvalds [Fri, 6 Nov 2020 20:58:11 +0000 (12:58 -0800)]
Merge tag 'sound-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Quite a bunch of small fixes that have been gathered since the last
pull, including changes like below:
- HD-audio runtime PM fixes and refactoring
- HD-audio and USB-audio quirks
- SOF warning fix
- Various ASoC device-specific fixes for Intel, Qualcomm, etc"
* tag 'sound-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: usb-audio: Add implicit feedback quirk for Qu-16
ASoC: mchp-spdiftx: Do not set Validity bit(s)
ALSA: usb-audio: Add implicit feedback quirk for MODX
ALSA: usb-audio: add usb vendor id as DSD-capable for Khadas devices
ALSA: hda/realtek - Enable headphone for ASUS TM420
ALSA: hda: prevent undefined shift in snd_hdac_ext_bus_get_link()
ASoC: qcom: lpass-cpu: Fix clock disable failure
ASoC: qcom: lpass-sc7180: Fix MI2S bitwidth field bit positions
ASoC: codecs: wcd9335: Set digital gain range correctly
ASoC: codecs: wcd934x: Set digital gain range correctly
ALSA: hda: Reinstate runtime_allow() for all hda controllers
ALSA: hda: Separate runtime and system suspend
ALSA: hda: Refactor codec PM to use direct-complete optimization
ALSA: hda/realtek - Fixed HP headset Mic can't be detected
ALSA: usb-audio: Add implicit feedback quirk for Zoom UAC-2
ALSA: make snd_kcontrol_new name a normal string
ALSA: fix kernel-doc markups
ASoC: SOF: loader: handle all SOF_IPC_EXT types
ASoC: cs42l51: manage mclk shutdown delay
ASoC: qcom: sdm845: set driver name correctly
...
Linus Torvalds [Fri, 6 Nov 2020 20:54:00 +0000 (12:54 -0800)]
Merge tag 'drm-fixes-2020-11-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"It's Friday here so that means another installment of drm fixes to
distract you from the counting process.
Changes all over the place, the amdgpu changes contain support for a
new GPU that is close to current one already in the tree (Green
Sardine) so it shouldn't have much side effects.
Otherwise imx has a few cleanup patches and fixes, amdgpu and i915
have around the usual smattering of fixes, fonts got constified, and
vc4/panfrost has some minor fixes. All in all a fairly regular rc3.
We have an outstanding nouveau regression, but the author is looking
into the fix, so should be here next week.
I now return you to counting.
fonts:
- constify font structures.
MAINTAINERS:
- Fix path for amdgpu power management
amdgpu:
- Add support for more navi1x SKUs
- Fix for suspend on CI dGPUs
- VCN DPG fix for Picasso
- Sienna Cichlid fixes
- Polaris DPM fix
- Add support for Green Sardine
amdkfd:
- Fix an allocation failure check
i915:
- Fix set domain's cache coherency
- Fixes around breadcrumbs
- Fix encoder lookup during PSR atomic
- Hold onto an explicit ref to i915_vma_work.pinned
- gvt: HWSP reset handling fix
- gvt: flush workaround
- gvt: vGPU context pin/unpin
- gvt: mmio cmd access fix for bxt/apl
imx:
- drop unused functions and callbacks
- reuse imx_drm_encoder_parse_of
- spinlock rework
- memory leak fix
- minor cleanups
vc4:
- resource cleanup fix
panfrost:
- madvise/shrinker fix"
* tag 'drm-fixes-2020-11-06-1' of git://anongit.freedesktop.org/drm/drm: (55 commits)
drm/amdgpu/display: remove DRM_AMD_DC_GREEN_SARDINE
drm/amd/display: Add green_sardine support to DM
drm/amd/display: Add green_sardine support to DC
drm/amdgpu: enable vcn support for green_sardine (v2)
drm/amdgpu: enable green_sardine_asd.bin loading (v2)
drm/amdgpu/sdma: add sdma engine support for green_sardine (v2)
drm/amdgpu: add gfx support for green_sardine (v2)
drm/amdgpu: add soc15 common ip block support for green_sardine (v3)
drm/amdgpu: add green_sardine support for gpu_info and ip block setting (v2)
drm/amdgpu: add Green_Sardine APU flag
drm/amdgpu: resolved ASD loading issue on sienna
amdkfd: Check kvmalloc return before memcpy
drm/amdgpu: update golden setting for sienna_cichlid
amd/amdgpu: Disable VCN DPG mode for Picasso
drm/amdgpu/swsmu: remove duplicate call to smu_set_default_dpm_table
drm/i915: Hold onto an explicit ref to i915_vma_work.pinned
drm/i915/gt: Flush xcs before tgl breadcrumbs
drm/i915/gt: Expose more parameters for emitting writes into the ring
drm/i915: Fix encoder lookup during PSR atomic check
drm/i915/gt: Use the local HWSP offset during submission
...
Linus Torvalds [Fri, 6 Nov 2020 20:51:29 +0000 (12:51 -0800)]
Merge tag 'tpmdd-next-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"Two critical tpm driver bug fixes"
* tag 'tpmdd-next-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: efi: Don't create binary_bios_measurements file for an empty log
tpm_tis: Disable interrupts on ThinkPad T490s
Linus Torvalds [Fri, 6 Nov 2020 20:48:19 +0000 (12:48 -0800)]
Merge tag 'iommu-fixes-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix a NULL-ptr dereference in the Intel VT-d driver
- Two fixes for Intel SVM support
- Increase IRQ remapping table size in the AMD IOMMU driver. The old
number of 128 turned out to be too low for some recent devices.
- Fix a mask check in generic IOMMU code
* tag 'iommu-fixes-v5.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix a check in iommu_check_bind_data()
iommu/vt-d: Fix a bug for PDP check in prq_event_thread
iommu/vt-d: Fix sid not set issue in intel_svm_bind_gpasid()
iommu/vt-d: Fix kernel NULL pointer dereference in find_domain()
iommu/amd: Increase interrupt remapping table limit to 512 entries
Linus Torvalds [Fri, 6 Nov 2020 20:44:23 +0000 (12:44 -0800)]
Merge tag 'vfio-v5.10-rc3' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Remove code by using existing helper (Zenghui Yu)
- fsl-mc copy-user return and underflow fixes (Dan Carpenter)
- fsl-mc static function declaration (Diana Craciun)
- Fix ioeventfd sleeping under spinlock (Alex Williamson)
- Fix pm reference count leak in vfio-platform (Zhang Qilong)
- Allow opening IGD device w/o OpRegion support (Fred Gao)
* tag 'vfio-v5.10-rc3' of git://github.com/awilliam/linux-vfio:
vfio/pci: Bypass IGD init in case of -ENODEV
vfio: platform: fix reference leak in vfio_platform_open
vfio/pci: Implement ioeventfd thread handler for contended memory lock
vfio/fsl-mc: Make vfio_fsl_mc_irqs_allocate static
vfio/fsl-mc: prevent underflow in vfio_fsl_mc_mmap()
vfio/fsl-mc: return -EFAULT if copy_to_user() fails
vfio/type1: Use the new helper to find vfio_group
Linus Torvalds [Fri, 6 Nov 2020 20:42:49 +0000 (12:42 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here's the weekly batch of fixes for arm64. Not an awful lot here, but
there are still a few unresolved issues relating to CPU hotplug, RCU
and IRQ tracing that I hope to queue fixes for next week.
Summary:
- Fix early use of kprobes
- Fix kernel placement in kexec_file_load()
- Bump maximum number of NUMA nodes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: try more regions if loading segments fails
arm64: kprobes: Use BRK instead of single-step when executing instructions out-of-line
arm64: NUMA: Kconfig: Increase NODES_SHIFT to 4
Linus Torvalds [Fri, 6 Nov 2020 20:29:08 +0000 (12:29 -0800)]
Merge tag 'arc-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Unbork HSDKv1 platform (won't boot) due to memory map issue
- Prevent stack unwinder from infinite looping
* tag 'arc-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk] Remap CCMs super early in asm boot trampoline
ARC: stack unwinding: avoid indefinite looping