V4L/DVB (10620): gspca - main: More checks of the device disconnection.
- prevent application oops when the device is disconnected
- wake up the application at disconnection time
- check the disconnection in ioctl dqbuf and poll
Tobias Lorenz [Thu, 12 Feb 2009 17:56:30 +0000 (14:56 -0300)]
V4L/DVB (10534): Output HW/SW version from scratchpad
This patch adds functions to access the scratchpad.
For it is this good for? In the first two bytes, the developers
stored the HW/PCB version and the software release of the firmware.
This is now written to syslog, so debugging get's easier.
Also knowing the versions is the key for flash upgrades later on.
There are also some cleanups of the flash report sizes.
Altogether this should justify the new version number 1.0.9.
Oldřich Jedlička [Thu, 12 Feb 2009 06:43:11 +0000 (03:43 -0300)]
V4L/DVB (10632): Added support for AVerMedia Cardbus Hybrid remote control
Added support for I2C device at address 0x40 and subaddress 0x0d/0x0b
that provides remote control key reading support for AVerMedia Cardbus
Hybrid card, possibly for other AVerMedia Cardbus cards.
The I2C address 0x40 doesn't like the SAA7134's 0xfd quirk, so it was
disabled.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10568): bttv: dynamically allocate device data
The bttv driver had static array of structures for up to 16 possible bttv
devices, even though few users have more than one or two. The structures
were quite large and this resulted in a huge BSS segment.
Change the driver to allocate the bttv device data dynamically, which
changes "struct bttv bttvs[BTTV_MAX]" to "struct bttv *bttvs[BTTV_MAX]".
It would be nice to get ride of "bttvs" entirely but there are some
complications with gpio access from the audio & mpeg drivers.
To help bttvs removal along anyway, I changed the open() methods use the
video device's drvdata to get the driver data instead of looking it up in
the bttvs array. This is also more efficient. Some WARN_ON()s are added
in cases the device node exists by the bttv device doesn't, which I don't
think should be possible.
The gpio access functions need to check if bttvs[card] is NULL now. Though
calling them on a non-existent card in the first place is wrong, but hard
to solve given the fundamental problems in how the gpio access code works.
This patch reduces the bss size by 66560 bytes on ia32. Overall change is a
reduction of 66398 bytes, as the WARN_ON()s add some 198 bytes.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10567): bttv: shrink muxsel data in card database
Over half of the card database was used to store muxsel data. 64 bytes
were used to store one 32 bit word for each of up to 16 inputs.
The Bt8x8 only has two bits to control its mux, so muxsel data for 16
inputs will fit into a single 32 bit word. There were a couple cards that
had special muxsel data that didn't fit in two bits, but I cleaned them up
in earlier patches.
Unfortunately, C doesn't allow us to have an array of bit fields. This
makes initializing the structure more of a pain. But with some cpp magic,
we can do it by changing:
.muxsel = { 2, 3, 0, 1 },
.muxsel = { 2, 2, 2, 2, 3, 3, 3, 3, 1, 1 },
Into:
.muxsel = MUXSEL(2, 3, 0, 1),
.muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),
That's not so bad. MUXSEL is a fancy macro that packs the arguments (of
which there can be one to sixteen!) into a single word two bits at a time.
It's a compile time constant (a variadic function wouldn't be) so we can
use it to initialize the structure. It's important the the arguments to
the macro only be plain decimal integers. Stuff like "0x01", "(2)", or
"MUX3" won't work properly.
I also created an accessor function, bttv_muxsel(btv, input), that gets the
mux bits for the selected input. It makes it cleaner to change the way the
muxsel data is stored.
This patch doesn't change the code size and decreases the datasegment by
9440 bytes.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10566): bttv: clean up mux code for IDS Eagle
This card apparently uses an external mux and the Bt878's mux should always
be set to MUX2. The values for the external mux control bits were stored
in the muxsel field. This meant that when changing inputs the driver would
switch the Bt878's mux to whatever value the external mux was supposed to
be set to, then eagle_muxsel() would switch it back to MUX2 and program the
external mux. This creates an unnecessary switch of the Bt878's mux.
So change muxsel to be 2 for each input. The external mux bits are just
"input&3" so they don't really need to be stored anywhere. This also
eliminates the last non-standard use of the muxsel data.
Cc: M G Berberich <berberic@fmi.uni-passau.de> Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10565): bttv: fix external mux for RemoteVision MX
Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2. Apparently
this was supposed to be for switching external audio muxes. Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.
The RemoteVision MX board used this feature to control an external video
mux and I guess no one noticed when they removed the code.
Move the extra gpio mux data out of the high nibble of muxsel and to
rv605_muxsel(), then have that function set the gpio lines with it.
From looking at the CD22M3494E datasheet, it seems like the mdelay(1) is a
much longer delay than necessary. It looks like only around 20 ns is
necessary.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10564): bttv: fix external mux for PHYTEC VD-009
Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2. Apparently
this was supposed to be for switching external audio muxes. Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.
These phytec boards used this feature to control an external video mux and
I guess no one noticed when they removed the code.
So add a muxsel_hook for these boards that does the necessary gpio setting.
BTW, I doubt the needs_tvaudio setting for these cards is correct.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10563): bttv: clean up mux code for IVC-120G
The card data for BTTV_BOARD_IVC120 set muxsel to a bunch of bogus values
(1 to 16), which the common mux code would use to set the Bt878's mux to
some random value. Then the custom code in ivc120_muxsel() would change
the Bt878's mux to the right value (always MUX0).
Better to just make the muxsel data correct (all zeros, easy!) and get the
mux right to begin with. Then the extra Bt878 mux setting code in
ivc120_muxsel() can be eliminated (the rest of the code for the IVC-120G's
external mux is still there of course).
This will help me clean up muxsel for some other changes. It should also
get rid of an unnecessary mux switch when changing from certain inputs to
certain other inputs on the IVC-120G.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10562): bttv: rework the way digital inputs are indicated
The code was using a muxsel value of -1U to indicate a digital input. A
couple places in were checking of muxsel < 0 to detect this, which doesn't
work of course because muxsel is unsigned and can't be negative.
Only a couple cards had digital inputs and it was always the last one, so
for the card database create a one bit field that indicates the last input
is digital. On init, this is used to set a new field in the bttv struct to
the digital input's number or UNSET for none. This makes it easier to
check if the current input is digital.
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10561): bttv: store card database more efficiently
The bttv card database is quite large and the data structure used to store
it wasn't very efficient. Most of the field are only used at card
initialization time so it doesn't matter if they aren't efficient to
access.
Overall the changes reduce code size by 60 bytes in ia32. The data size is
decreased by 5024 byes. It is probably even more for 64-bit kernels.
Move the fields in the struct around to be sorted from largest to smallest.
This saves on padding space used for alignment.
Get rid of the unused digital_mode field. Leave the setting as a comment
in the few cards entries that set it, in case someone ever writes the code.
Get rid of the unused audio_inputs field. Leave the values in the card
entries in case someone ever writes code that might use it.
Get ride of the unused radio_addr field. No card entries even set it to
anything interesting so it's not left as comments. All the code that used
it was removed in commit v2.6.14-3466-g291d1d7 from Nov 8th 2005.
Reduce video_inputs to u8 as no card has more than 255 inputs (the most is
16).
Change tuner_addr to u8. I2C addresses are only seven bits and 255 means
ADDR_UNSET, so everything fits.
Make has_radio a one bit flag.
Make the pll setting a two bit field.
Reduce svhs to four bits as no card has an s-video input above 9. Change
the value for no s-video input from UNSET (which is -1U and out of range of
four bits) to NO_SVHS (which is now 15).
Trent Piepho [Thu, 29 Jan 2009 00:32:59 +0000 (21:32 -0300)]
V4L/DVB (10560): bttv: make tuner card info more consistent
The bttv card database structure had a "tuner" field that was the input
number of the tuner input or UNSET for no tuner. However, the only values
it could ever be are 0 and UNSET. Having a tuner on an input other than 0
didn't work and was never used.
There is also a "tuner_type" field that can be set to TUNER_ABSENT to
indicate no tuner, which makes "tuner = UNSET" redundant. In many cases,
tuner_type was set to UNSET when there was no tuner, which isn't quite
correct. tuner_type == UNSET is supposed to mean the tuner type isn't yet
known.
So, I changed cards where "tuner == UNSET" to always have tuner_type of
TUNER_ABSENT. At this point the tuner field is redundant, so I deleted it.
I have the card setup code set the card's tuner_type (not the card type's
tuner_type!) to TUNER_ABSENT if it hasn't yet been set at the end of the
setup code. Various places that check if the card has a tuner will now
look for this instead of checking the card type's "tuner" field.
Also autoload the tuner module before issuing the TUNER_SET_TYPE_ADDR I2C
client call instead of after issuing it.
Overall, on ia32 this decreases compiled code size by about 24 bytes and
reduces the data size by 640 bytes.
The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API. This doesn't work of
course and results in the PAL path always being taken.
What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880. This is wrong because changing the norm on one card will also
affect other cards of the same type. Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.
Changing the norm would also cause the audio to become unmuted.
Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.
Trent Piepho [Thu, 29 Jan 2009 00:32:58 +0000 (21:32 -0300)]
V4L/DVB (10558): bttv: norm value should be unsigned
The norm value in the driver is an index into an array and the the driver
doesn't allow it to be negative or otherwise invalid. It should be
unsigned but wasn't in all places.
Fix some structs and functions to have the norm be unsigned. Get rid of
useless checks for "< 0". Most of the driver code can't handle a norm
value that's out of range, so change some ">= BTTV_TVNORMS" checks to
BUG_ON(). There's no point in silently ignoring invalid driver state just
to crash because of it later.
Hans Verkuil [Fri, 13 Feb 2009 08:12:02 +0000 (05:12 -0300)]
V4L/DVB (10540): cx2341x: fixed bug causing several audio controls to be no longer listed
The cx2341x_mpeg_ctrls array must be ordered by control ID. I know that
this is bad design, but for now I will just fix this bug and revisit it
when all drivers have moved to v4l2_device/v4l2_subdev, since that will
allow me to do greatly improve control handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tobias Lorenz [Thu, 12 Feb 2009 17:55:45 +0000 (14:55 -0300)]
V4L/DVB (10530): Documentation and code cleanups
- "DealExtreme" sells the "PCear" radio and that comes from "Sanei Electric".
- MPlayer is also usable as radio application.
- Consistent usage of tabulators and blanks in the code.
Nicola Soranzo [Wed, 11 Feb 2009 02:28:24 +0000 (23:28 -0300)]
V4L/DVB (10525): em28xx: Coding style fixes and a typo correction
Lots of coding style fixes and a typo correction for em28xx.
[dougsland@redhat.com: fixed a reject due to a change on em28xx-audio.c] Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Robert Krakora [Sun, 8 Feb 2009 16:10:39 +0000 (13:10 -0300)]
V4L/DVB (10519): em28xx: Fix for em28xx audio startup
Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any
data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion.
It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and
reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (10512): tda1004x: Fix eeprom firmware load on boards with 16MHz Xtal
For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.
It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.
Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
KBL is not needed on saa7134, so, let's remove it.
However, we should take some care to avoid opening the module while
initializing it. This issue exists with newer udev's that opens a device
as soon as the driver is registered. So, a proper lock is needed on
open.
V4L/DVB (10507): saa7134: Fix analog mode on devices that need to open an i2c gate
Some saa7134 devices require to open an i2c gate before tuning. This
patch fix the initialization for those devices.
The nxt200x_gate_ctrl() logic were returned back to the old place, since
we don't know how to close the gate. A future pacth could revert that
change and provide the proper close gate control, to avoid keeping it
open forever.
V4L/DVB (10506): saa7134: move tuner init code to saa7134-cards
On certain devices, before opening a tuner, we need to open the tuner
gate via i2c.
This patch just moves the tuner probing code to the same place where
such i2c commands are handled, to make easier to fix this trouble on
later patches.
V4L/DVB (10504): tda827x: Be sure that gate will be open/closed at the proper time
The gate control logic is broken: several routines just keep it open;
other rotines close it properly; there are even other routines that
assumes that it is open without really checking or opening it.
Instead of having to manually handle the gate control and having such
troubles, let a sub-routine take care of the gate, opening it before
i2c_transfer and closing it after that. This avoids leaving the gate
into a random state.
Cc: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 7 Feb 2009 23:42:33 +0000 (20:42 -0300)]
V4L/DVB (10502): saa7146: move v4l2 device registration to saa7146_vv.
Doing the v4l2_device registration in the saa7146 core will make it
dependent on v4l2, even for DVB-only boards. This registration and
unregistration belongs in saa7146_vv instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 7 Feb 2009 14:18:05 +0000 (11:18 -0300)]
V4L/DVB (10499): saa7146: convert saa7146 and mxb in particular to v4l2_subdev.
Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).
Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.
Converted saa5246a and saa5249 to v4l2_subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 7 Feb 2009 14:00:02 +0000 (11:00 -0300)]
V4L/DVB (10490): v4l2: prefill ident and revision from v4l2_dbg_chip_ident.
Drivers that implement this always have to set the ident and revision
to V4L2_IDENT_NONE and 0. Do this in the v4l2 core so drivers don't have
to do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Alexey Klimov [Thu, 5 Feb 2009 11:56:07 +0000 (08:56 -0300)]
V4L/DVB (10460): radio-mr800: add stereo support
Patch introduces new amradio_set_stereo function.
Driver calls this func to make stereo radio reception.
Corrects checking of returned value after usb_bulk_msg.
Alexey Klimov [Thu, 5 Feb 2009 11:53:02 +0000 (08:53 -0300)]
V4L/DVB (10458): radio-mr800: move radio start and stop in one function
Patch introduces new amradio_set_mute function. Amradio_start and
amradio_stop removed. This makes driver more flexible and it's useful
for next changes.
Andy Walls [Mon, 9 Feb 2009 01:40:04 +0000 (22:40 -0300)]
V4L/DVB (10446): cx18: Finally get sliced VBI working - for 525 line 60 Hz systems at least
Sliced VBI, in the manner that ivtv implements it as a separate data stream,
now works for 525 line 60 Hz systems like NTSC-M. It may work for 625 line
50 Hz systems, but I have more engineering work to do, to verify it is operating
properly. Sliced data insertion into the MPEG PS should be working, but is
untested.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 7 Feb 2009 18:47:28 +0000 (15:47 -0300)]
V4L/DVB (10445): cx18: Process Raw VBI on a whole frame basis; fix VBI buffer size
The cx23418 appears to send Raw VBI buffers with a PTS on a per frame
basis, not per field, so process Raw VBI on a whole frame basis and reduce
some complexity. Fix VBI buffer size computation to handle a whole
frame of Raw VBI for a 625 line system, which is the worst case and will
work for 525 lines systems as well.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 7 Feb 2009 04:31:22 +0000 (01:31 -0300)]
V4L/DVB (10444): cx18: Fix sliced VBI PTS and fix artifacts in last raw line of field
Fixed an endianess problem with the collection of the PTS from
the VBI buffer given to us by the encoder. Also extrapolated the
last 12 bytes of the last line of each field, to remove artifacts
created by removing the first 12 bytes of each field for raw VBI.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Fri, 6 Feb 2009 21:33:43 +0000 (18:33 -0300)]
V4L/DVB (10442): cx18: Fixes for enforcing when Encoder Raw VBI params can be set
The Encoder will only allow the Raw VBI parameters, along with a number of
other API parameters, to take effect when no analog captures are in
progress. These parameters must be set before the first analog capture starts,
be it MPEG, VBI, YUV, etc., and cannot be changed until the last one stops. It
is not obvious to me what capture channel API parameters are shared and which
ones must be set per capture channel, so set them all for every analog
capture channel start up. This fixes the driver so that VBI capture can be
started up after the MPEG capture is going.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Mon, 2 Feb 2009 00:42:12 +0000 (21:42 -0300)]
V4L/DVB (10440): cx18: Fix presentation timestamp (PTS) for VBI buffers
The old code from ivtv used a CX23415/6 PTS, which was simply left at 0 in the
cx18 driver. Since the CX23418 gives us what I think is a PTS (or some other
90 kHz clock count) with each VBI buffer, this change has the cx18 driver use
that as a PTS.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 31 Jan 2009 01:39:26 +0000 (22:39 -0300)]
V4L/DVB (10434): cx18: Smarter verification of CX18_AUDIO_ENABLE register writes
The CX18_AUDIO_ENABLE register usually never reads back what was just written
under normal circumstances. Perform better checking that a write went to the
register as expected with a specification of what bits to verify.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mirror_ubuntu-disco-kernel.git / log