Luca Coelho [Wed, 6 Nov 2019 07:27:51 +0000 (09:27 +0200)]
iwlwifi: add support for version 2 of SOC_CONFIGURATION_CMD
This new command is mostly backwards compatible, with the exception
that the device_type element was changed into a bitmask. The device
type bit remains the same (because we only had 0 and 1 anyway), but
when using v1 we can't set any other bits, because that would change
the integer.
Other than that, the struct remains the same and the driver can set
the device_type bit in both cases, but it can only set the low_latency
bit if VER_2 is used.
Luca Coelho [Mon, 4 Nov 2019 19:29:55 +0000 (21:29 +0200)]
iwlwifi: convert QnJ with Jf devices to new config table
All the QnJ devices have a similar matching to the other Qu devices,
but needs a different configuration. Convert the QnJ devices to the
new table accordingly.
Luca Coelho [Mon, 4 Nov 2019 19:02:47 +0000 (21:02 +0200)]
iwlwifi: convert all Qu with Jf devices to the new config table
Add new generic iwl_trans structures for these devices and apply the
correct cfg depending on the device characteristics.
Since we have to match Qu with IWL_CONFIG_ANY, we also need to move
the Hr devices to the new table, but for now we keep matching on PCI
device and subsystem device IDs.
Luca Coelho [Mon, 4 Nov 2019 15:29:55 +0000 (17:29 +0200)]
iwlwifi: add HW step to new cfg device table
We need to use different firmware versions for different HW steps with
certain devices. Prepare for this differentiation by adding HW step
to the new device table.
Luca Coelho [Mon, 4 Nov 2019 10:31:22 +0000 (12:31 +0200)]
iwlwifi: move integrated, extra_phy and soc_latency to trans_cfg
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Luca Coelho [Mon, 4 Nov 2019 09:53:41 +0000 (11:53 +0200)]
iwlwifi: remove redundant iwl9560_2ac_cfg struct
The iwl9560_2ac_cfg struct is used for PNJ devices and the
configuration is the same as iwl9260_2ac_cfg, so we can remove the
former to avoid redundancy.
Modify adaptive dwell number of APs override API
Instead of using channel to index mapping, add the adaptive dwell
override parameters as part of the configuration per channel in the scan
request command.
Support 2 different override values and use them as follows:
1. 10 APs for friendly GO channels in p2p scan.
2. 2 APs for social channels in p2p scan.
Change-Id: I3b461108abf2306c3d054099112f2c3afce1cc92 Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Luca Coelho [Fri, 1 Nov 2019 13:31:02 +0000 (15:31 +0200)]
iwlwifi: yoyo: add PCI config space region type
Add a new region type that allows us to dump the PCI config space.
This is mostly the same as dumping a memory region, but reading from
the device's config space instead.
In order to make this generic and independent of the trans type, we
make a function called iwl_dump_ini_config_iter() that calls a new op
in the transport to read its config space.
Some devices require longer time to stabilize the power and XTAL.
This is especially true for devices integrated in the SoC. Add
support for a new firmware API that allows the driver to set the
latency value accordingly.
Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12 Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tzu-En Huang [Thu, 26 Mar 2020 02:04:08 +0000 (10:04 +0800)]
rtw88: fix non-increase management packet sequence number
In previous setting, management packets' sequence numbers will
not increase and always stay at 0. Add hw sequence number support
for mgmt packets.
The table below shows different sequence number setting in the
tx descriptor.
Wright Feng [Wed, 25 Mar 2020 08:20:28 +0000 (03:20 -0500)]
brcmfmac: add USB autosuspend feature support
We add enable dynamic suspend (autosuspend) support in host driver, and
it can let platform cut down idle power consumption.
To support autosuspend feature in host driver, kernel need to be built
with CONFIG_USB_SUSPEND and autosuspend need to be turn on.
And we also replace wowl feature with adding "needs_remote_wakeup", so
that host still can be waken by wireless device.
Madhan Mohan R [Wed, 25 Mar 2020 08:20:27 +0000 (03:20 -0500)]
brcmfmac: increase max hanger slots from 1K to 3K in fws layer
Will enable FMAC to push more packets to bus tx queue and help
improve throughput when fws queuing is enabled. This change is
required to tune the throughput for passing WMM CERT tests.
Raveendran Somu [Wed, 25 Mar 2020 08:20:26 +0000 (03:20 -0500)]
brcmfmac: fix the incorrect return value in brcmf_inform_single_bss().
The function brcmf_inform_single_bss returns the value as success,
even when the length exceeds the maximum value.
The fix is to send appropriate code on this error.
This issue is observed when Cypress test group reported random fmac
crashes when running their tests and the path was identified from the
crash logs. With this fix the random failure issue in Cypress test group
was resolved.
Raveendran Somu [Wed, 25 Mar 2020 08:20:25 +0000 (03:20 -0500)]
brcmfmac: Fix double freeing in the fmac usb data path
When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.
Raveendran Somu [Wed, 25 Mar 2020 08:20:24 +0000 (03:20 -0500)]
brcmfmac: Fix driver crash on USB control transfer timeout
When the control transfer gets timed out, the error status
was returned without killing that urb, this leads to using
the same urb. This issue causes the kernel crash as the same
urb is sumbitted multiple times. The fix is to kill the
urb for timeout transfer before returning error
Chris Chiu [Fri, 20 Mar 2020 06:38:33 +0000 (14:38 +0800)]
rtl8xxxu: Feed current txrate information for mac80211
The nl80211 commands such as 'iw link' can't get current txrate
information from the driver. This commit fills in the tx rate
information from the C2H RA report in the sta_statistics function.
Chris Chiu [Fri, 20 Mar 2020 06:38:32 +0000 (14:38 +0800)]
rtl8xxxu: add enumeration for channel bandwidth
There's a data field in H2C and C2H commands which is used to
carry channel bandwidth information. Add enumeration to make it
more descriptive in code.
Yan-Hsuan Chuang [Fri, 13 Mar 2020 03:30:07 +0000 (11:30 +0800)]
rtw88: add a debugfs entry to enable/disable coex mechanism
Sometimes we need to stop the coex mechanism to debug, so that we
can manually control the device through various outer commands.
Hence, add a new debugfs coex_enable to allow us to enable/disable
the coex mechanism when driver is running.
To disable coex
echo 0 > /sys/kernel/debug/ieee80211/phyX/rtw88/coex_enable
To enable coex
echo 1 > /sys/kernel/debug/ieee80211/phyX/rtw88/coex_enable
To check coex dm is enabled or not
cat /sys/kernel/debug/ieee80211/phyX/rtw88/coex_enable
Yan-Hsuan Chuang [Fri, 13 Mar 2020 03:30:06 +0000 (11:30 +0800)]
rtw88: add a debugfs entry to dump coex's info
Add a new entry "coex_info" in debugfs to dump coex's states for
us to debug on coex's issues.
The basic concept for co-existence (coex, usually for WiFi + BT)
is to decide a strategy based on the current status of WiFi and
BT. So, it means the WiFi driver requires to gather information
from BT side and choose a strategy (TDMA/table/HW settings).
Althrough we can easily check the current status of WiFi, e.g.,
from kernel log or just dump the hardware registers, it is still
very difficult for us to gather so many different types of WiFi
states (such as RFE config, antenna, channel/band, TRX, Power
save). Also we will need BT's information that is stored in
"struct rtw_coex". So it is necessary for us to have a debugfs
that can dump all of the WiFi/BT information required.
Note that to debug on coex related issues, we usually need a
longer period of time of coex_info dump every 2 seconds (for
example, 30 secs, so we should have 15 times of coex_info's
dump).
Jakub Kicinski [Tue, 24 Mar 2020 17:30:16 +0000 (10:30 -0700)]
devlink: expand the devlink-info documentation
We are having multiple review cycles with all vendors trying
to implement devlink-info. Let's expand the documentation with
more information about what's implemented and motivation behind
this interface in an attempt to make the implementations easier.
Describe what each info section is supposed to contain, and make
some references to other HW interfaces (PCI caps).
Document how firmware management is expected to look, to make
it clear how devlink-info and devlink-flash work in concert.
Name some future work.
v2: - improve wording
v3: - improve wording
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 24 Mar 2020 14:13:58 +0000 (16:13 +0200)]
net: phy: mscc: consolidate a common RGMII delay implementation
It looks like the VSC8584 PHY driver is rolling its own RGMII delay
configuration code, despite the fact that the logic is mostly the same.
In fact only the register layout and position for the RGMII controls has
changed. So we need to adapt and parameterize the PHY-dependent bit
fields when calling the new generic function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Changelog v2 .. v3:
- Use two "left-shifts by 16" to fix builds with 32-bit phys_addr_t
- reorder variable declarations
Changelog v1 .. v2:
- Add Reviewed-by: tags from Radhey
- Extend kerndoc documentation
- Convert DMA error handler tasklet to work queue
- log DMA mapping errors
- mark DMA mapping error checks as unlikely (in "hot" paths)
- return NETDEV_TX_OK on TX DMA mapping error (increasing TX drop counter)
- Request eth IRQ as an optional IRQ
- Remove no longer needed MDIO IRQ register names
- Drop DT propery check for address width, assume full 64 bit
This series updates the Xilinx Axienet driver to work on our board
here. One big issue was broken SGMII support, which Russell fixed already
(in net-next).
While debugging and understanding the driver, I found several problems
in the error handling and cleanup paths, which patches 2-7 address.
Patch 8 removes a annoying error message, patch 9 paves the way for newer
revisions of the IP. The next patch adds mii-tool support, just for good
measure.
The next four patches add support for 64-bit DMA. This is an integration
option on newer IP revisions (>= v7.1), and expects MSB bits in formerly
reserved registers. Without writing to those MSB registers, the state
machine won't trigger, so it's mandatory to access them, even if they
are zero. Patches 11 and 12 prepare the code by adding accessors, to
wrap this properly and keep it working on older IP revisions.
Patch 13 enables access to the MSB registers, by trying to write a
non-zero value to them and checking if that sticks. Older IP revisions
always read those registers as zero.
Patch 14 then adjusts the DMA mask, based on the autodetected MSB
feature. It uses the full 64 bits in this case, the rest of the system
(actual physical addresses in use) should provide a natural limit if the
chip has connected fewer address lines. If not, the parent DT node can
use a dma-range property.
The Xilinx PG138 and PG021 documents (in versions 7.1 in both cases)
were used for this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:47 +0000 (13:23 +0000)]
net: axienet: Allow DMA to beyond 4GB
With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.
This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:46 +0000 (13:23 +0000)]
net: axienet: Autodetect 64-bit DMA capability
When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.
To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.
The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:45 +0000 (13:23 +0000)]
net: axienet: Upgrade descriptors to hold 64-bit addresses
Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.
If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.
For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:44 +0000 (13:23 +0000)]
net: axienet: Wrap DMA pointer writes to prepare for 64 bit
Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.
Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:43 +0000 (13:23 +0000)]
net: axienet: Add mii-tool support
mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:40 +0000 (13:23 +0000)]
net: axienet: Check for DMA mapping errors
Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:39 +0000 (13:23 +0000)]
net: axienet: Factor out TX descriptor chain cleanup
Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:38 +0000 (13:23 +0000)]
net: axienet: Improve DMA error handling
Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.
Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:37 +0000 (13:23 +0000)]
net: axienet: Fix DMA descriptor cleanup path
When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.
Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions
This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:36 +0000 (13:23 +0000)]
net: axienet: Propagate failure of DMA descriptor setup
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 13:23:34 +0000 (13:23 +0000)]
net: xilinx: temac: Relax Kconfig dependencies
Similar to axienet, the temac driver is now architecture agnostic, and
can be at least compiled for several architectures.
Especially the fact that this is a soft IP for implementing in FPGAs
makes the current restriction rather pointless, as it could literally
appear on any architecture, as long as an FPGA is connected to the bus.
The driver hasn't been actually tried on any hardware, it is just a
drive-by patch when doing the same for axienet (a similar patch for
axienet is already merged).
This (temac and axienet) have been compile-tested for:
alpha hppa64 microblaze mips64 powerpc powerpc64 riscv64 s390 sparc64
(using kernel.org cross compilers).
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.
The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).
Fixes: f70bb06563ed ("ethtool: update mapping of features to legacy ioctl requests") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2020 23:15:58 +0000 (16:15 -0700)]
Merge tag 'wireless-drivers-next-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.
When merging with wireless-drivers this pull request has a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve that just drop the changes from commit cf52c8a776d1 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a3831 (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.
Major changes:
qtnfmac
* support WPA3 SAE and OWE in AP mode
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
mt76
* MT7663 support for the MT7615 driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
PTP_CLK pin configuration for SJA1105 DSA driver
This series adds support for the PTP_CLK pin on SJA1105 to be configured
via the PTP subsystem, in the "periodic output" and "external timestamp
input" modes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 23 Mar 2020 22:59:24 +0000 (00:59 +0200)]
net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT
The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.
On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.
The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
- When emitting a oneshot pulse, instead of being told when to emit it,
the switch just does it "now" and tells you later what time it was,
via the PTPSYNCTS register. [ Incidentally, this is the same register
that the slave uses to collect the ext_ts timestamp from, too. ]
- On the sync slave, there is no interrupt mechanism on reception of a
new extts, and no FIFO to buffer them, because in the foreseen use
case, software is in control of both the master and the slave pins,
so it "knows" when there's something to collect.
These 2 problems mean that:
- We don't support (at least yet) the quirky oneshot mode exposed by
the hardware, just normal periodic output.
- We abuse the hardware a little bit when we expose generic extts.
Because there's no interrupt mechanism, we need to poll at double the
frequency we expect to receive a pulse. Currently that means a
non-configurable "twice a second".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 23 Mar 2020 22:59:23 +0000 (00:59 +0200)]
net: dsa: sja1105: make the AVB table dynamically reconfigurable
The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.
Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 23 Mar 2020 22:59:22 +0000 (00:59 +0200)]
net: dsa: sja1105: make future_base_time a common helper
Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 23 Mar 2020 22:59:21 +0000 (00:59 +0200)]
net: dsa: sja1105: unconditionally set DESTMETA and SRCMETA in AVB table
These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.
These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.
The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.
This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2020 05:00:03 +0000 (22:00 -0700)]
Merge branch 'introduce-read_poll_timeout'
Dejin Zheng says:
====================
introduce read_poll_timeout
This patch sets is introduce read_poll_timeout macro, it is an extension
of readx_poll_timeout macro. the accessor function op just supports only
one parameter in the readx_poll_timeout macro, but this macro can
supports multiple variable parameters for it. so functions like
phy_read(struct phy_device *phydev, u32 regnum) and
phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
use this poll timeout framework.
the first patch introduce read_poll_timeout macro, and the second patch
redefined readx_poll_timeout macro by read_poll_timeout(), and the other
patches are examples using read_poll_timeout macro.
v6 -> v7:
- add a parameter to supports that it can sleep some time
before read operation in read_poll_timeout macro.
- add prefix with double underscores for some variable to avoid
any variable re-declaration or shadowing in patch 3 and patch
7.
v5 -> v6:
- add some check to keep the code more similar in patch 8
v4 -> v5:
- add some msleep() before call phy_read_mmd_poll_timeout() to
keep the code more similar in patch 6 and patch 9.
- add a patch of drop by v4, it can add msleep before call
phy_read_poll_timeout() to keep the code more similar.
v3 -> v4:
- add 3 examples of using new functions.
- deal with precedence issues for parameter cond.
- drop a patch about phy_poll_reset() function.
v2 -> v3:
- modify the parameter order of newly added functions.
phy_read_mmd_poll_timeout(val, cond, sleep_us, timeout_us, \
phydev, devaddr, regnum)
||
\/
phy_read_mmd_poll_timeout(phydev, devaddr regnum, val, cond, \
sleep_us, timeout_us)
phy_read_poll_timeout(val, cond, sleep_us, timeout_us, \
phydev, regnum)
||
\/
phy_read_poll_timeout(phydev, regnum, val, cond, sleep_us, \
timeout_us)
v1 -> v2:
- passed a phydev, device address and a reg to replace args...
parameter in phy_read_mmd_poll_timeout() by Andrew Lunn 's
suggestion in patch 3. Andrew Lunn <andrew@lunn.ch>, Thanks
very much for your help!
- also in patch 3, handle phy_read_mmd return an error(the return
value < 0) in phy_read_mmd_poll_timeout(). Thanks Andrew
again.
- in patch 6, pass a phydev and a reg to replace args...
parameter in phy_read_poll_timeout(), and also handle the
phy_read() function's return error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:06:00 +0000 (23:06 +0800)]
net: phy: tja11xx: use phy_read_poll_timeout() to simplify the code
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:05:59 +0000 (23:05 +0800)]
net: phy: smsc: use phy_read_poll_timeout() to simplify the code
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:05:57 +0000 (23:05 +0800)]
net: phy: introduce phy_read_poll_timeout macro
it is sometimes necessary to poll a phy register by phy_read()
function until its value satisfies some condition. introduce
phy_read_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:05:55 +0000 (23:05 +0800)]
net: phy: aquantia: use phy_read_mmd_poll_timeout() to simplify the code
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:05:54 +0000 (23:05 +0800)]
net: phy: bcm84881: use phy_read_mmd_poll_timeout() to simplify the code
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
it is sometimes necessary to poll a phy register by phy_read_mmd()
function until its value satisfies some condition. introduce
phy_read_mmd_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng [Mon, 23 Mar 2020 15:05:51 +0000 (23:05 +0800)]
iopoll: introduce read_poll_timeout macro
this macro is an extension of readx_poll_timeout macro. the accessor
function op just supports only one parameter in the readx_poll_timeout
macro, but this macro can supports multiple variable parameters for
it. so functions like phy_read(struct phy_device *phydev, u32 regnum)
and phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
also use this poll timeout core. and also expand it can sleep some time
before read operation.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng zengkai [Mon, 23 Mar 2020 06:51:16 +0000 (14:51 +0800)]
net: thunderx: remove set but not used variable 'tail'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
variable tail set but not used [-Wunused-but-set-variable]
It's not used since commit 4863dea3fab01("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng zengkai <zhengzengkai@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 22 Mar 2020 21:09:57 +0000 (14:09 -0700)]
net: dsa: Implement flow dissection for tag_brcm.c
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
devlink: Preparations for trap policers support
This patch set prepares the code for devlink-trap policer support in a
follow-up patch set [1][2]. No functional changes intended.
Policers are going to be added as attributes of packet trap groups,
which are entities used to aggregate logically related packet traps.
This will allow users, for example, to limit all the packets that
encountered an exception during routing to 10Kpps.
However, currently, device drivers register their packet trap groups
implicitly when they register their packet traps via
devlink_traps_register(). This makes it difficult to pass additional
attributes for the groups. For example, the policer bound to the group.
Therefore, this patch set converts device drivers to explicitly register
their packet trap groups. This will later allow these drivers to
register the group with additional attributes, if any.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 22 Mar 2020 18:48:30 +0000 (20:48 +0200)]
devlink: Only pass packet trap group identifier in trap structure
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 22 Mar 2020 18:48:29 +0000 (20:48 +0200)]
devlink: Stop reference counting packet trap groups
Now that drivers explicitly register their supported packet trap groups
there is no for devlink to create them on-demand and destroy them when
their reference count reaches zero.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 22 Mar 2020 18:48:28 +0000 (20:48 +0200)]
netdevsim: Explicitly register packet trap groups
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 22 Mar 2020 18:48:27 +0000 (20:48 +0200)]
mlxsw: spectrum_trap: Explicitly register packet trap groups
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 22 Mar 2020 18:48:26 +0000 (20:48 +0200)]
devlink: Add API to register packet trap groups
Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.
This makes it difficult for drivers to pass additional attributes for
the groups.
Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.
Next patches will convert existing drivers to use this API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 22 Mar 2020 18:03:56 +0000 (19:03 +0100)]
r8169: improve RTL8168b FIFO overflow workaround
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sun, 22 Mar 2020 18:03:06 +0000 (19:03 +0100)]
r8169: improve rtl_schedule_task
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2020 04:21:33 +0000 (21:21 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-21
Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.
This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.
Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
octeontx2-vf: Add network driver for virtual function
This patch series adds network driver for the virtual functions of
OcteonTX2 SOC's resource virtualization unit (RVU).
Changes from v3:
* Removed missed out EXPORT symbols in VF driver.
Changes from v2:
* Removed Copyright license text.
* Removed wrapper fn()s around mutex_lock and unlock.
* Got rid of using macro with 'return'.
* Removed __weak fn()s.
- Sugested by Leon Romanovsky and Andrew Lunn
Changes from v1:
* Removed driver version and fixed authorship
* Removed driver version and fixed authorship in the already
upstreamed AF, PF drivers.
* Removed unnecessary checks in sriov_enable and xmit fn()s.
* Removed WQ_MEM_RECLAIM flag while creating workqueue.
* Added lock in tx_timeout task.
* Added 'supported_coalesce_params' in ethtool ops.
* Minor other cleanups.
- Sugested by Jakub Kicinski
====================
Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Fri, 20 Mar 2020 18:57:25 +0000 (00:27 +0530)]
octeontx2-af: Remove driver version and fix authorship
Removed MODULE_VERSION and fixed MODULE_AUTHOR.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Fri, 20 Mar 2020 18:57:24 +0000 (00:27 +0530)]
octeontx2-pf: Cleanup all receive buffers in SG descriptor
With MTU sized receive buffers it is not expected to have CQE_RX
with multiple receive buffer pointers. But since same physcial link
is shared by PF and it's VFs, the max receive packet configured
at link could be morethan MTU. Hence there is a chance of receiving
plts morethan MTU which then gets DMA'ed into multiple buffers
and notified in a single CQE_RX. This patch treats such pkts as errors
and frees up receive buffers pointers back to hardware.
Also on the transmit side this patch sets SMQ MAXLEN to max value to avoid
HW length errors for the packets whose size > MTU, eg due to path MTU.
Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Fri, 20 Mar 2020 18:57:23 +0000 (00:27 +0530)]
octeontx2-vf: Link event notification support
VF shares physical link with PF. Admin function (AF) sends
notification to PF whenever a link change event happens. PF
has to forward the same notification to each of the enabled VF.
PF traps START/STOP_RX messages sent by VF to AF to keep track of
VF's enabled/disabled state.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Fri, 20 Mar 2020 18:57:22 +0000 (00:27 +0530)]
octeontx2-vf: Ethtool support
Added ethtool support for VF devices for
- Driver stats, Tx/Rx perqueue stats
- Set/show Rx/Tx queue count
- Set/show Rx/Tx ring sizes
- Set/show IRQ coalescing parameters
- RSS configuration etc
It's the PF which owns the interface, hence VF
cannot display underlying CGX interface stats.
Except for this rest ethtool support reuses PF's
APIs.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tomasz Duszynski [Fri, 20 Mar 2020 18:57:21 +0000 (00:27 +0530)]
octeontx2-vf: Virtual function driver support
On OcteonTx2 silicon there two two types VFs, VFs that share the
physical link with their parent SR-IOV PF and the VFs which work
in pairs using internal HW loopback channels (LBK). Except for the
underlying Rx/Tx channel mapping from netdev functionality perspective
they are almost identical. This patch adds netdev driver support
for these VFs.
Unlike it's parent PF a VF cannot directly communicate with admin
function (AF) and it has to go through PF for the same. The mailbox
communication with AF works like 'VF <=> PF <=> AF'.
Also functionality wise VF and PF are identical, hence to avoid code
duplication PF driver's APIs are resued here for HW initialization,
packet handling etc etc ie almost everything. For VF driver to compile
as module exported few of the existing PF driver APIs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Geetha sowjanya [Fri, 20 Mar 2020 18:57:20 +0000 (00:27 +0530)]
octeontx2-pf: Handle VF function level reset
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleanups all resources attached
to that VF.
Also handled IRQs triggered when master enable bit is cleared
or set for VFs. This handler just clears the transaction pending
ie TRPEND bit.
Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Fri, 20 Mar 2020 18:57:19 +0000 (00:27 +0530)]
octeontx2-pf: Enable SRIOV and added VF mbox handling
Added 'sriov_configure' to enable/disable virtual functions (VFs).
Also added handling of mailbox messages from these VFs.
Admin function (AF) is the only one with all priviliges to configure
HW, alloc resources etc etc, PFs and it's VFs have to request AF
via mbox for all their needs. But unlike PFs, their VFs cannot
send a mbox request directly. A VF shares a mailbox region with
it's parent PF, so VF sends a mailbox msg to PF and then PF forwards
it to AF. Then AF after processing sends response to PF which it
again forwards to VF.
This patch adds support for this 'VF <=> PF <=> AF' mailbox
communication.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Christina Jacob <cjacob@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 24 Mar 2020 04:09:47 +0000 (21:09 -0700)]
Merge branch 'phy_check_downshift'
Heiner Kallweit says:
====================
net: phy: add and use phy_check_downshift
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2: Add downshift hint to phy_print_status().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 20 Mar 2020 16:51:38 +0000 (17:51 +0100)]
net: phy: add and use phy_check_downshift
So far PHY drivers have to check whether a downshift occurred to be
able to notify the user. To make life of drivers authors a little bit
easier move the downshift notification to phylib. phy_check_downshift()
compares the highest mutually advertised speed with the actual value
of phydev->speed (typically read by the PHY driver from a
vendor-specific register) to detect a downshift.
v2:
- Add downshift hint to phy_print_status
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_cnt: Fix 64-bit division in mlxsw_sp_counter_resources_register
When building arm32 allyesconfig:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_cnt.c
>>> net/ethernet/mellanox/mlxsw/spectrum_cnt.o:(mlxsw_sp_counter_resources_register) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o)
pool_size and bank_size are u64; use div64_u64 so that 32-bit platforms
do not error.
Fixes: ab8c4cc60420 ("mlxsw: spectrum_cnt: Move config validation along with resource register") Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 19 Mar 2020 23:26:23 +0000 (16:26 -0700)]
net: sched: rename more stats_types
Commit 53eca1f3479f ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log