_rtl_pci_find_adapter fail path will jump to label fail3 for
unsupported adapter types.
However, on course for fail3 there will be call rtl_deinit_core
before rtl_init_core.
For the inclusion of checking pci_iounmap this fail can be moved to
fail2.
Fixes
[ 4.492963] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4.493067] IP: rtl_deinit_core+0x31/0x90 [rtlwifi]
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This adds Intel(R) Trace Hub PCI ID for Cannon Lake PCH-LP.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This adds Intel(R) Trace Hub PCI ID for Cannon Lake PCH-H.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0. Fix this by shifting only by 4 bits to correctly get the upper nybble.
Detected by CoverityScan, CID#142891 ("Operands don't affect result")
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
BugLink: https://bugs.launchpad.net/bugs/1678477 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
For asynchronous operation, SGs are allocated without a page mapped to
them or with a page that is not used (ref-counted). If the SGL is freed,
the code must only call put_page for an SG if there was a page assigned
and ref-counted in the first place.
This fixes a kernel crash when using io_submit with more than one iocb
using the sendmsg and sendpage (vmsplice/splice) interface.
Signed-off-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The race was introduced by me in commit 971316f0503a ("epoll:
ep_unregister_pollwait() can use the freed pwq->whead"). I did not
realize that nothing can protect eventpoll after ep_poll_callback() sets
->whead = NULL, only whead->lock can save us from the race with
ep_free() or ep_remove().
Move ->whead = NULL to the end of ep_poll_callback() and add the
necessary barriers.
TODO: cleanup the ewake/EPOLLEXCLUSIVE logic, it was confusing even
before this patch.
Hopefully this explains use-after-free reported by syzcaller:
BUG: KASAN: use-after-free in debug_spin_lock_before
...
_raw_spin_lock_irqsave+0x4a/0x60 kernel/locking/spinlock.c:159
ep_poll_callback+0x29f/0xff0 fs/eventpoll.c:1148
this is spin_lock(eventpoll->lock),
...
Freed by task 17774:
...
kfree+0xe8/0x2c0 mm/slub.c:3883
ep_free+0x22c/0x2a0 fs/eventpoll.c:865
Fixes: 971316f0503a ("epoll: ep_unregister_pollwait() can use the freed pwq->whead") Reported-by: 范龙飞 <long7573@126.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In kvm_free_stage2_pgd() we check the stage2 PGD before holding
the lock and proceed to take the lock if it is valid. And we unmap
the page tables, followed by releasing the lock. We reset the PGD
only after dropping this lock, which could cause a race condition
where another thread waiting on or even holding the lock, could
potentially see that the PGD is still valid and proceed to perform
a stage2 operation and later encounter a NULL PGD.
When fail to get needed page for pool, need to put allocated pages
into pool. But current code has a miscalculation of allocated pages,
correct it.
Signed-off-by: Xiangliang.Yu <Xiangliang.Yu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Monk Liu <monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The 'dir' parameter in xfrm_migrate() is a user-controlled byte which is used
as an array index. This can lead to an out-of-bound access, kernel lockup and
DoS. Add a check for the 'dir' value.
This fixes CVE-2017-11600.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1474928 Fixes: 80c9abaabf42 ("[XFRM]: Extension for dynamic update of endpoint address(es)") Reported-by: "bo Zhang" <zhangbo5891001@gmail.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
[ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
.owner_cpu: 0
[ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W 4.12.0-03002-gec979a4-dirty #40
[ 5668.772796] Hardware name: Nokia RX-51 board
[ 5668.773071] Workqueue: phy1 wl1251_irq_work
[ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
(show_stack+0x10/0x14)
[ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
(do_raw_spin_lock+0x6c/0xa0)
[ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
(_raw_spin_lock_irqsave+0x10/0x18)
[ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
(wl1251_op_tx+0x38/0x5c)
[ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
(ieee80211_tx_frags+0x188/0x1c0)
[ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
(__ieee80211_tx+0x6c/0x130)
[ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
(ieee80211_tx+0xdc/0x104)
[ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
(__ieee80211_subif_start_xmit+0x454/0x8c8)
[ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
[<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
[ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
[<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...
by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Recent patch had an endian warning ie
cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup()
Signed-off-by: Steve French <smfrench@gmail.com> CC: Ronnie Sahlberg <lsahlber@redhat.com> Acked-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
tests/attr.c: In function 'store_event':
tests/attr.c:66:27: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__u64 {aka long unsigned int}' [-Werror=format=]
snprintf(path, PATH_MAX, "%s/event-%d-%llu-%d", dir,
^
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The memory_pressure control file was incorrectly set up without
a private value (0, by default). As a result, this control
file was treated like memory_migrate on read. By adding back the
FILE_MEMORY_PRESSURE private value, the correct memory pressure value
will be returned.
Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Fixes: 7dbdb199d3bf ("cgroup: replace cftype->mode with CFTYPE_WORLD_WRITABLE") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When !NUMA, cpumask_of_node(@node) equals cpu_online_mask regardless of
@node. The assumption seems that if !NUMA, there shouldn't be more than
one node and thus reporting cpu_online_mask regardless of @node is
correct. However, that assumption was broken years ago to support
DISCONTIGMEM and whether a system has multiple nodes or not is
separately controlled by NEED_MULTIPLE_NODES.
This means that, on a system with !NUMA && NEED_MULTIPLE_NODES,
cpumask_of_node() will report cpu_online_mask for all possible nodes,
indicating that the CPUs are associated with multiple nodes which is an
impossible configuration.
This bug has been around forever but doesn't look like it has caused any
noticeable symptoms. However, it triggers a WARN recently added to
workqueue to verify NUMA affinity configuration.
Fix it by reporting empty cpumask on non-zero nodes if !NUMA.
ceph_readpage() unlocks page prematurely prematurely in the case
that page is reading from fscache. Caller of readpage expects that
page is uptodate when it get unlocked. So page shoule get locked
by completion callback of fscache_read_or_alloc_pages()
Signed-off-by: "Yan, Zheng" <zyan@redhat.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com> Tested-by: Dan Priamo <danp@adiengineering.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support") Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
drivers/gpu/drm/i915/intel_uncore.c: In function ‘hsw_unclaimed_reg_detect’:
drivers/gpu/drm/i915/intel_uncore.c:638:36: warning: decrement of a boolean expression [-Wbool-operation]
i915.mmio_debug = mmio_debug_once--;
^~
As it's really not wise to -- on a boolean value.
Commit 7571494004d8 ("drm/i915: Do one shot unclaimed mmio detection
less frequently") which showed up in 4.6-rc1 does solve this issue, by
rewriting the mmio detection logic, but that isn't really good to
backport to 4.4-stable, so just fix up the obvious logic here to do the
right thing.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Paulo Zanoni <przanoni@gmail.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Once the reserved page array is unused we can reset the 'res_in_use'
state; here we can do a lazy update without holding the mutex as we only
need to check against concurrent access, not concurrent release.
[mkp: checkpatch]
Fixes: 1bc0eb044615 ("scsi: sg: protect accesses to 'reserved' page array") Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Todd Poynor <toddpoynor@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The 'reserved' page array is used as a short-cut for mapping data,
saving us to allocate pages per request. However, the 'reserved' array
is only capable of holding one request, so this patch introduces a mutex
for protect 'sg_fd' against concurrent accesses.
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[toddpoynor@google.com: backport to 3.18-4.9, fixup for bad ioctl
SG_SET_FORCE_LOW_DMA code removed in later versions and not modified by
the original patch.]
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Todd Poynor <toddpoynor@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are some tricky dependencies between the different stages of
flushing the FPSIMD register state during exec, and these can race
with context switch in ways that can cause the old task's regs to
leak across. In particular, a context switch during the memset() can
cause some of the task's old FPSIMD registers to reappear.
Disabling preemption for this small window would be no big deal for
performance: preemption is already disabled for similar scenarios
like updating the FPSIMD registers in sigreturn.
So, instead of rearranging things in ways that might swap existing
subtle bugs for new ones, this patch just disables preemption
around the FPSIMD state flushing so that races of this type can't
occur here. This brings fpsimd_flush_thread() into line with other
code paths.
Fixes: 674c242c9323 ("arm64: flush FP/SIMD state correctly after execve()") Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The x86 version of insb/insw/insl uses an inline assembly that does
not have the target buffer listed as an output. This can confuse
the compiler, leading it to think that a subsequent access of the
buffer is uninitialized:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_mgmt_scan_confirm’:
drivers/net/wireless/wl3501_cs.c:665:9: error: ‘sig.status’ is used uninitialized in this function [-Werror=uninitialized]
drivers/net/wireless/wl3501_cs.c:668:12: error: ‘sig.cap_info’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c: In function 'sb1000_rx':
drivers/net/sb1000.c:775:9: error: 'st[0]' is used uninitialized in this function [-Werror=uninitialized]
drivers/net/sb1000.c:776:10: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c:784:11: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I tried to mark the exact input buffer as an output here, but couldn't
figure it out. As suggested by Linus, marking all memory as clobbered
however is good enough too. For the outs operations, I also add the
memory clobber, to force the input to be written to local variables.
This is probably already guaranteed by the "asm volatile", but it can't
hurt to do this for symmetry.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@suse.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Link: http://lkml.kernel.org/r/20170719125310.2487451-5-arnd@arndb.de Link: https://lkml.org/lkml/2017/7/12/605 Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When there's a fatal signal pending, arm64's do_page_fault()
implementation returns 0. The intent is that we'll return to the
faulting userspace instruction, delivering the signal on the way.
However, if we take a fatal signal during fixing up a uaccess, this
results in a return to the faulting kernel instruction, which will be
instantly retried, resulting in the same fault being taken forever. As
the task never reaches userspace, the signal is not delivered, and the
task is left unkillable. While the task is stuck in this state, it can
inhibit the forward progress of the system.
To avoid this, we must ensure that when a fatal signal is pending, we
apply any necessary fixup for a faulting kernel instruction. Thus we
will return to an error path, and it is up to that code to make forward
progress towards delivering the fatal signal.
Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Laura Abbott <labbott@redhat.com> Reviewed-by: Steve Capper <steve.capper@arm.com> Tested-by: Steve Capper <steve.capper@arm.com> Reviewed-by: James Morse <james.morse@arm.com> Tested-by: James Morse <james.morse@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When the switch is rebooted, the lpfc driver fails to log
into the fabric, and Unexpected timeout message is seen.
Fix: Do not issue RegVFI if the FLOGI was internally aborted.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com> Signed-off-by: James Smart <james.smart@avagotech.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
gcc 7 complains:
drivers/net/wireless/intersil/p54/fwio.c: In function 'p54_scan':
drivers/net/wireless/intersil/p54/fwio.c:491:4: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]
Fix that by passing the correct size to memset.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
David reported that the length for memset was incorrect (element sizes
were not taken into account). Then I saw that we are clearing kzalloced
memory, so we can simply drop this code.
Reported-by: David Binderman <dcb314@hotmail.com> Reviewed-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are a few calls of memset() to stream->resources, but they all
are called in a wrong size, sizeof(unsigned char) * VORTEX_RESOURCE_LAST,
while this field is a u32 array. This may leave the memories not
zero-cleared.
Fix it by replacing them with a simpler sizeof(stream->resources)
instead.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
isci/remote_node_context.c: In function 'sci_remote_node_context_destruct':
isci/remote_node_context.c:69:16: error: array subscript is above array bounds [-Werror=array-bounds]
This is odd, since we clearly cover all values for enum
scis_sds_remote_node_context_states here. Anyway, checking for an array
overflow can't harm and it makes the warning go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When removing a GHES device notified by SCI, list_del_rcu() is used,
ghes_remove() should call synchronize_rcu() before it goes on to call
kfree(ghes), otherwise concurrent RCU readers may still hold this list
entry after it has been freed.
Signed-off-by: James Morse <james.morse@arm.com> Reviewed-by: "Huang, Ying" <ying.huang@intel.com> Fixes: 81e88fdc432a (ACPI, APEI, Generic Hardware Error Source POLL/IRQ/NMI notification type support) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The on-stack resource-window 'win' in setup_res() is not
properly initialized. This causes the pointers in the
embedded 'struct resource' to contain stale addresses.
These pointers (in my case the ->child pointer) later get
propagated to the global iomem_resources list, causing a #GP
exception when the list is traversed in
iomem_map_sanity_check().
Fixes: c183619b63ec (x86/irq, ACPI: Implement ACPI driver to support IOAPIC hotplug) Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A divide by zero error occurs if qp_count is less than mw_count because
num_qps_mw is calculated to be zero. The calculation appears to be
incorrect.
The requirement is for num_qps_mw to be set to qp_count / mw_count
with any remainder divided among the earlier mws.
For example, if mw_count is 5 and qp_count is 12 then mws 0 and 1
will have 3 qps per window and mws 2 through 4 will have 2 qps per window.
Thus, when mw_num < qp_count % mw_count, num_qps_mw is 1 higher
than when mw_num >= qp_count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers") Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In cases where there are more mw's than spads/2-2, the mw count gets
reduced to match the limitation. ntb_transport also tries to ensure that
there are fewer qps than mws but uses the full mw count instead of
the reduced one. When this happens, the math in
'ntb_transport_setup_qp_mw' will get confused and result in a kernel
paging request bug.
This patch fixes the bug by reducing qp_count to the reduced mw count
instead of the full mw count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers") Acked-by: Allen Hubbe <Allen.Hubbe@dell.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the "clock-frequency" DT property is not found, req_rate is used
uninitialized, and the "audio_clkout" clock will be created with an
arbitrary clock rate.
This uninitialized kernel stack data may leak to userspace through
/sys/kernel/debug/clk/clk_summary, cfr. the value in the "rate" column:
Current Renesas sound driver doesn't have 1:1 relationship between
stream <-> mod because it is supporting MIX. Because of this reason
rsnd_mod_interrupt() is searching correspond mod by for loop.
But this loop is not needed, because each mod has own type.
This patch avoid pointless loop by using mod->type.
This patch is good for SSI-parent support, because stream might have
2 SSI as SSI-parent/child. SSI interrupt handler will be called twice
if stream has SSI-parent without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Because SRC is connected to DMA and DMA want to keep dreq when stop
timing. This patch makes SRC stop SRC.out only when stop timing. And
it stops both SRC.out/SRC.in when quit timing
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit e22579713ae1 ("ASoC: simple card: set cpu-dai sysclk
with mclk-fs") added sysclk / SND_SOC_CLOCK_OUT setting, that makes
asoc_simple_card_hw_params fail if the operation is not supported,
although the intention clearly was to ignore ENOTSUPP. Fix it.
The patch fixes audio playback on Kirkwood / OpenRD client,
where the following errors are seen:
Fixes: e22579713ae1 ("ASoC: simple card: set cpu-dai sysclk with mclk-fs") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Tested-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit c4ea41ba195d ("binder: use group leader instead of open thread")'
was incomplete and didn't update a check in binder_mmap(), causing all
mmap() calls into the binder driver to fail.
Signed-off-by: Martijn Coenen <maco@android.com> Tested-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use wake_up_interruptible_sync() to hint to the scheduler binder
transactions are synchronous wakeups. Disable preemption while waking
to avoid ping-ponging on the binder lock.
The binder allocator assumes that the thread that
called binder_open will never die for the lifetime of
that proc. That thread is normally the group_leader,
however it may not be. Use the group_leader instead
of current.
Signed-off-by: Todd Kjos <tkjos@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Regardless of which events form a group, it does not make sense for the
events to target different tasks and/or CPUs, as this leaves the group
inconsistent and impossible to schedule. The core perf code assumes that
these are consistent across (successfully intialised) groups.
Core perf code only verifies this when moving SW events into a HW
context. Thus, we can violate this requirement for pure SW groups and
pure HW groups, unless the relevant PMU driver happens to perform this
verification itself. These mismatched groups subsequently wreak havoc
elsewhere.
For example, we handle watchpoints as SW events, and reserve watchpoint
HW on a per-CPU basis at pmu::event_init() time to ensure that any event
that is initialised is guaranteed to have a slot at pmu::add() time.
However, the core code only checks the group leader's cpu filter (via
event_filter_match()), and can thus install follower events onto CPUs
violating thier (mismatched) CPU filters, potentially installing them
into a CPU without sufficient reserved slots.
This can be triggered with the below test case, resulting in warnings
from arch backends.
int main(int argc, char *argv[])
{
int leader, ret;
cpu_set_t cpus;
/*
* Force use of CPU0 to ensure our CPU0-bound events get scheduled.
*/
CPU_ZERO(&cpus);
CPU_SET(0, &cpus);
ret = sched_setaffinity(0, sizeof(cpus), &cpus);
if (ret) {
printf("Unable to set cpu affinity\n");
return 1;
}
/* open leader event, bound to this task, CPU0 only */
leader = perf_event_open(&wp_attr, 0, 0, -1, 0);
if (leader < 0) {
printf("Couldn't open leader: %d\n", leader);
return 1;
}
/*
* Open a follower event that is bound to the same task, but a
* different CPU. This means that the group should never be possible to
* schedule.
*/
ret = perf_event_open(&wp_attr, 0, 1, leader, 0);
if (ret < 0) {
printf("Couldn't open mismatched follower: %d\n", ret);
return 1;
} else {
printf("Opened leader/follower with mismastched CPUs\n");
}
/*
* Open as many independent events as we can, all bound to the same
* task, CPU0 only.
*/
do {
ret = perf_event_open(&wp_attr, 0, 0, -1, 0);
} while (ret >= 0);
/*
* Force enable/disble all events to trigger the erronoeous
* installation of the follower event.
*/
printf("Opened all events. Toggling..\n");
for (;;) {
prctl(PR_TASK_PERF_EVENTS_DISABLE, 0, 0, 0, 0);
prctl(PR_TASK_PERF_EVENTS_ENABLE, 0, 0, 0, 0);
}
return 0;
}
Fix this by validating this requirement regardless of whether we're
moving events.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Zhou Chengming <zhouchengming1@huawei.com> Link: http://lkml.kernel.org/r/1498142498-15758-1-git-send-email-mark.rutland@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When processing an NFSv4 WRITE operation, argp->end should never
point past the end of the data in the final page of the page list.
Otherwise, nfsd4_decode_compound can walk into uninitialized memory.
More critical, nfsd4_decode_write is failing to increment argp->pagelen
when it increments argp->pagelist. This can cause later xdr decoders
to assume more data is available than really is, which can cause server
crashes on malformed requests.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The df for a SMB2 share triggers a GetInfo call for
FS_FULL_SIZE_INFORMATION. The values returned are used to populate
struct statfs.
The problem is that none of the information returned by the call
contains the total blocks available on the filesystem. Instead we use
the blocks available to the user ie. quota limitation when filling out
statfs.f_blocks. The information returned does contain Actual free units
on the filesystem and is used to populate statfs.f_bfree. For users with
quota enabled, it can lead to situations where the total free space
reported is more than the total blocks on the system ending up with df
reports like the following
# df -h /mnt/a
Filesystem Size Used Avail Use% Mounted on
//192.168.22.10/a 2.5G -2.3G 2.5G - /mnt/a
To fix this problem, we instead populate both statfs.f_bfree with the
same value as statfs.f_bavail ie. CallerAvailableAllocationUnits. This
is similar to what is done already in the code for cifs and df now
reports the quota information for the user used to mount the share.
# df --si /mnt/a
Filesystem Size Used Avail Use% Mounted on
//192.168.22.10/a 2.7G 101M 2.6G 4% /mnt/a
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Pierguido Lambri <plambri@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The function create_filter() is passed a 'filterp' pointer that gets
allocated, and if "set_str" is true, it is up to the caller to free it, even
on error. The problem is that the pointer is not freed by create_filter()
when set_str is false. This is a bug, and it is not up to the caller to free
the filter on error if it doesn't care about the string.
Link: http://lkml.kernel.org/r/1502705898-27571-2-git-send-email-chuhu@redhat.com Fixes: 38b78eb85 ("tracing: Factorize filter creation") Reported-by: Chunyu Hu <chuhu@redhat.com> Tested-by: Chunyu Hu <chuhu@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The VSL and HSL bits in the DSMR register set the corresponding
horizontal and vertical sync signal polarity to active high. The code
got it the wrong way around, fix it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There is a bug in the setting of the DES (Display Enable Signal)
register. This current setting occurs 1 dot left shift. The DES
register should be set minus one value about the specifying value
with H/W specification. This patch corrects it.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When an encoder fails to initialize the driver prints an error message
to the kernel log. The message contains the name of the encoder's DT
node, which is NULL for internal encoders. Use the of_node_full_name()
macro to avoid dereferencing a NULL pointer, print the output number to
add more context to the error, and make sure we still own a reference to
the encoder's DT node by delaying the of_node_put() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Thong Ho <thong.ho.px@rvc.renesas.com> Signed-off-by: Nhan Nguyen <nhan.nguyen.yb@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The last part of drm_atomic_check_only is testing whether we need to
fail with -EINVAL when modeset is not allowed, but forgets to return
the value when atomic_check() fails first.
This results in -EDEADLK being replaced by -EINVAL, and the sanity
check in drm_modeset_drop_locks kicks in:
This is also a bugfix because we could end up rejecting updates with
-EINVAL because of a early -EDEADLK, while if atomic_check ran to
completion it might have downgraded the modeset to a fastset.
This is the same bug as we fixed in commit f6cd7daecff5 ("drm: Release
driver references to handle before making it available again"), but now
the exposure is via the PRIME lookup tables. If we remove the
object/handle from the PRIME lut, then a new request for the same
object/fd will generate a new handle, thus for a short window that
object is known to userspace by two different handles. Fix this by
releasing the driver tracking before PRIME.
Fixes: 0ff926c7d4f0 ("drm/prime: add exported buffers to current fprivs
imported buffer list (v2)") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Thierry Reding <treding@nvidia.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170819120558.6465-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The commit 8503ff166504 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.
However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.
Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.
More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.
To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.
Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.
It should also be noted that this change does not fix commit 8503ff166504
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: John Stultz <john.stultz@linaro.org> Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It is necessary to explicitly set both SLC_AUX_RGN_START1 and SLC_AUX_RGN_END1
which hold MSB bits of the physical address correspondingly of region start
and end otherwise SLC region operation is executed in unpredictable manner
Without this patch, SLC flushes on HSDK (IOC disabled) were taking
seconds.
Reported-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: PAR40 regs only written if PAE40 exist] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When user tries to replace the user-defined control TLV, the kernel
checks the change of its content via memcmp(). The problem is that
the kernel passes the return value from memcmp() as is. memcmp()
gives a non-zero negative value depending on the comparison result,
and this shall be recognized as an error code.
The patch covers that corner-case, return 1 properly for the changed
TLV.
Fixes: 8aa9b586e420 ("[ALSA] Control API - more robust TLV implementation") Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This important to call qdisc_tree_reduce_backlog() after changing queue
length. Parent qdisc should deactivate class in ->qlen_notify() called from
qdisc_tree_reduce_backlog() but this happens only if qdisc->q.qlen in zero.
Missed class deactivations leads to crashes/warnings at picking packets
from empty qdisc and corrupting state at reactivating this class in future.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 86a7996cc8a0 ("net_sched: introduce qdisc_replace() helper") Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As we know in some target's checkentry it may dereference par.entryinfo
to check entry stuff inside. But when sched action calls xt_check_target,
par.entryinfo is set with NULL. It would cause kernel panic when calling
some targets.
It can be reproduce with:
# tc qd add dev eth1 ingress handle ffff:
# tc filter add dev eth1 parent ffff: u32 match u32 0 0 action xt \
-j ECN --ecn-tcp-remove
It could also crash kernel when using target CLUSTERIP or TPROXY.
By now there's no proper value for par.entryinfo in ipt_init_target,
but it can not be set with NULL. This patch is to void all these
panics by setting it with an ipt_entry obj with all members = 0.
Note that this issue has been there since the very beginning.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
list.dev has not been initialized and so the copy_to_user is copying
data from the stack back to user space which is a potential
information leak. Fix this ensuring all of list is initialized to
zero.
Detected by CoverityScan, CID#1357894 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In some situations tcp_send_loss_probe() can realize that it's unable
to send a loss probe (TLP), and falls back to calling tcp_rearm_rto()
to schedule an RTO timer. In such cases, sometimes tcp_rearm_rto()
realizes that the RTO was eligible to fire immediately or at some
point in the past (delta_us <= 0). Previously in such cases
tcp_rearm_rto() was scheduling such "overdue" RTOs to happen at now +
icsk_rto, which caused needless delays of hundreds of milliseconds
(and non-linear behavior that made reproducible testing
difficult). This commit changes the logic to schedule "overdue" RTOs
ASAP, rather than at now + icsk_rto.
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)") Suggested-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
syzcaller reported the following use-after-free issue in rt6_select():
BUG: KASAN: use-after-free in rt6_select net/ipv6/route.c:755 [inline] at addr ffff8800bc6994e8
BUG: KASAN: use-after-free in ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084 at addr ffff8800bc6994e8
Read of size 4 by task syz-executor1/439628
CPU: 0 PID: 439628 Comm: syz-executor1 Not tainted 4.3.5+ #8
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 0000000000000000ffff88018fe435b0ffffffff81ca384dffff8801d3588c00 ffff8800bc699380ffff8800bc699500dffffc0000000000ffff8801d40a47c0 ffff88018fe435d8ffffffff81735751ffff88018fe43660ffff8800bc699380
Call Trace:
[<ffffffff81ca384d>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffffff81ca384d>] dump_stack+0xc1/0x124 lib/dump_stack.c:51
sctp: [Deprecated]: syz-executor0 (pid 439615) Use of struct sctp_assoc_value in delayed_ack socket option.
Use struct sctp_sack_info instead
[<ffffffff81735751>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158
[<ffffffff817359c4>] print_address_description mm/kasan/report.c:196 [inline]
[<ffffffff817359c4>] kasan_report_error+0x1b4/0x4a0 mm/kasan/report.c:285
[<ffffffff81735d93>] kasan_report mm/kasan/report.c:305 [inline]
[<ffffffff81735d93>] __asan_report_load4_noabort+0x43/0x50 mm/kasan/report.c:325
[<ffffffff82a28e39>] rt6_select net/ipv6/route.c:755 [inline]
[<ffffffff82a28e39>] ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084
[<ffffffff82a28fb1>] ip6_pol_route_output+0x81/0xb0 net/ipv6/route.c:1203
[<ffffffff82ab0a50>] fib6_rule_action+0x1f0/0x680 net/ipv6/fib6_rules.c:95
[<ffffffff8265cbb6>] fib_rules_lookup+0x2a6/0x7a0 net/core/fib_rules.c:223
[<ffffffff82ab1430>] fib6_rule_lookup+0xd0/0x250 net/ipv6/fib6_rules.c:41
[<ffffffff82a22006>] ip6_route_output+0x1d6/0x2c0 net/ipv6/route.c:1224
[<ffffffff829e83d2>] ip6_dst_lookup_tail+0x4d2/0x890 net/ipv6/ip6_output.c:943
[<ffffffff829e889a>] ip6_dst_lookup_flow+0x9a/0x250 net/ipv6/ip6_output.c:1079
[<ffffffff82a9f7d8>] ip6_datagram_dst_update+0x538/0xd40 net/ipv6/datagram.c:91
[<ffffffff82aa0978>] __ip6_datagram_connect net/ipv6/datagram.c:251 [inline]
[<ffffffff82aa0978>] ip6_datagram_connect+0x518/0xe50 net/ipv6/datagram.c:272
[<ffffffff82aa1313>] ip6_datagram_connect_v6_only+0x63/0x90 net/ipv6/datagram.c:284
[<ffffffff8292f790>] inet_dgram_connect+0x170/0x1f0 net/ipv4/af_inet.c:564
[<ffffffff82565547>] SYSC_connect+0x1a7/0x2f0 net/socket.c:1582
[<ffffffff8256a649>] SyS_connect+0x29/0x30 net/socket.c:1563
[<ffffffff82c72032>] entry_SYSCALL_64_fastpath+0x12/0x17
Object at ffff8800bc699380, in cache ip6_dst_cache size: 384
The root cause of it is that in fib6_add_rt2node(), when it replaces an
existing route with the new one, it does not update fn->rr_ptr.
This commit resets fn->rr_ptr to NULL when it points to a route which is
replaced in fib6_add_rt2node().
Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Wei Wang <weiwan@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When msg->rep skb is freed, set the pointer to NULL,
so that caller does not free it again.
[1]
==================================================================
BUG: KASAN: use-after-free in skb_push+0xd4/0xe0 net/core/skbuff.c:1466
Read of size 8 at addr ffff8801c6e71e90 by task syz-executor5/4115
Memory state around the buggy address: ffff8801c6e71d80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8801c6e71e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801c6e71e80: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff8801c6e71f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8801c6e71f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
KMSAN reported use of uninitialized sctp_addr->v4.sin_addr.s_addr and
sctp_addr->v6.sin6_scope_id in sctp_v6_cmp_addr() (see below).
Make sure all fields of an IPv6 address are initialized, which
guarantees that the IPv4 fields are also initialized.
Signed-off-by: Alexander Potapenko <glider@google.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When sfq_enqueue() drops head packet or packet from another queue it
have to update backlog at upper qdiscs too.
Fixes: 2ccccf5fb43f ("net_sched: update hierarchical backlog too") Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If fi->fib_metrics could not be allocated in fib_create_info()
we attempt to dereference a NULL pointer in free_fib_info_rcu() :
m = fi->fib_metrics;
if (m != &dst_default_metrics && atomic_dec_and_test(&m->refcnt))
kfree(m);
Before my recent patch, we used to call kfree(NULL) and nothing wrong
happened.
Instead of using RCU to defer freeing while we are under memory stress,
it seems better to take immediate action.
This was reported by syzkaller team.
Fixes: 3fb07daff8e9 ("ipv4: add reference counting to metrics") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
syszkaller team reported another problem in DCCP [1]
Problem here is that the structure holding RTO timer
(ccid2_hc_tx_rto_expire() handler) is freed too soon.
We can not use del_timer_sync() to cancel the timer
since this timer wants to grab socket lock (that would risk a dead lock)
Solution is to defer the freeing of memory when all references to
the socket were released. Socket timers do own a reference, so this
should fix the issue.
[1]
==================================================================
BUG: KASAN: use-after-free in ccid2_hc_tx_rto_expire+0x51c/0x5c0 net/dccp/ccids/ccid2.c:144
Read of size 4 at addr ffff8801d2660540 by task kworker/u4:7/3365
Memory state around the buggy address: ffff8801d2660400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8801d2660480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8801d2660500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8801d2660580: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc ffff8801d2660600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>