Vivien Didelot [Sat, 11 Mar 2017 21:13:03 +0000 (16:13 -0500)]
etherdevice: remove unused eth_addr_greater
eth_addr_greater() was introduced for the mv88e6xxx driver, but is not
used anymore. There is no other user, thus remove this function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:13:02 +0000 (16:13 -0500)]
net: dsa: mv88e6xxx: add port priority override op
Add a new operation to disable the DA, SA and VTU priority override.
Setting such limit is not likely to be used soon, so provide a
port_disable_pri_override operation directly. This can be changed later
for port_set_pri_override when we'll need it.
Also remove the now obsolete mv88e6xxx_6320_family helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:13:01 +0000 (16:13 -0500)]
net: dsa: mv88e6xxx: add port ATU learn limit op
Add a new operation to disable the limiting of learnt MAC addresses.
Setting such limit is not likely to be used soon, so provide a
port_disable_learn_limit operation directly. This can be changed later
for port_set_learn_limit when we'll need it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:13:00 +0000 (16:13 -0500)]
net: dsa: mv88e6xxx: fix port egress flooding mode
The Marvell switch ports can be configured to allow or prevent egress of
frames with an unknown unicast or multicast destination address.
Some switch chips such as 88E6095 and 88E6185 have two disjoint bits in
Port Control Register (0x04) bit 2 "Forward Unknown" (for unicast) and
Port Control 2 Register (0x08) bit 6 "Default Forward" (for multicast).
Other chips such as 88E6085, 88E6123, 88E6352, and 88E6390 have a 2-bit
value in Port Control Register (0x04) bits 3:2 "EgressFloods".
The current code does not fully implement the disjoint bits variant and
assigns incorrect ones to some chip models. Fix that with two
implementation references (6185 and 6352 that I currently have) of a
port_set_egress_floods operation (as named in datasheets).
Old chips such as 88E6060 don't have egress flooding mode, so don't
error out if the operation is not provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:59 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rework port mode setup
A switch port mode is defined by the association of its egress mode, its
frame mode and if supported or required, the ether type value.
Pack all this in a mv88e6xxx_set_port_mode function and provide helpers
for the Normal Network mode, the DSA mode, and the Ether Type DSA mode,
as well as an helper to setup a port's mode depending on its nature.
Define PORT_ETH_TYPE_DEFAULT for the 0x9100 reset value of port E Type.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:58 +0000 (16:12 -0500)]
net: dsa: add dsa_is_normal_port helper
Introduce a dsa_is_normal_port helper to check if a given port is a
normal user port as opposed to a CPU port or DSA link.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:57 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rename the port vector member
Not all Marvell switch chips support port trunking, which is embedded in
the port vector data for ATU operations.
Rename the portv_trunkid member of the mv88e6xxx_atu_entry structure to
portvec to be more concise and consistent with the different chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:56 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rename new FID helper
Rename the _mv88e6xxx_fid_new helper to mv88e6xxx_atu_new to get rid of
the old underscore prefix naming convention and be consistent with the
rest of the chip-wide ATU API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:55 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rework ATU Remove
Add a fresh documented implementation of the ATU Move operation, and use
it to replace the current ATU Remove operation.
Note that not all Marvell switch chip support the ATU Move operation.
For those supporting it, the number of bits used to mask the destination
port may vary. 6352 and such use 4-bit, while 6390 use 5-bit. Thus add a
new atu_move_port_mask member in the info structure to describe the
presence and variant of ATU Move operation.
Note that the ATU Move operation is not documented in the 6185 datasheet
but the chip does support the operation.
All remaining _mv88e6xxx_atu_* functions are now unused as well as the
MV88E6XXX_FLAG_G1_ATU_FID flag, thus remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:53 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rework ATU GetNext
Add and use a fresh documented implementation of the ATU GetNext.
Since it is not necessary to write the MAC address to iterate from, only
do it once directly in the ATU GetNext operation, if the provided ATU
entry structure is not valid. This makes the user code simpler.
Also, there is no need to loop when getting a single ATU entry. So
remove the mv88e6xxx_atu_get helper and add a simpler snippet in
mv88e6xxx_port_db_load_purge to lookup a given MAC address.
The _mv88e6xxx_atu_mac_{read,write} are not used anymore thus remove
them. _mv88e6xxx_atu_data_{read,write} are still used so keep them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:52 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: rework ATU Load/Purge
All Marvell switch chips have an ATU accessed using the same Global (1)
register layout. Only the handling of the FID differs as more bits were
necessary to support more and more databases.
Add and use a fresh documented implementation of the ATU Load/Purge.
The static mv88e6xxx_g1_atu_{fid_write,op_wait,op,data_write,mac_write}
functions won't need to be exposed in the end so for the moment keep
their counterparts _mv88e6xxx_atu_{wait,cmd,data_write,mac_write} as is,
since they are still used by other ATU operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:50 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: setup message ports
All interconnectable Marvell switch chips have an ATU Learn2All feature
which allows newly learnt addresses to be spanned on ports marked as
"Message Port".
This commit configures the DSA ports as Message Port. Note that this has
no effect until the Learn2All feature is enabled.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:49 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: add ATU setup helper
Move the configuration of the default ageing time in a new
mv88e6xxx_atu_setup function.
That function will be extended later to contain all ATU related
configuration bits.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:48 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: move ATU ageing time setter
Move the ATU ageing time setter code in a new global1_atu.c file, which
will be extended in future patches to contains all consequent Global (1)
ATU support code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 11 Mar 2017 21:12:47 +0000 (16:12 -0500)]
net: dsa: mv88e6xxx: add port mask helper
Add a mv88e6xxx_port_mask() helper to get the bitmask of ports in a
switch chip, that will be used in several features.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Mar 2017 06:50:15 +0000 (23:50 -0700)]
Merge branch 'mlxsw-tc-flower-offload-stats'
Jiri Pirko says:
====================
mlxsw: Add support for TC flower offload statistics
Arkadi says:
This patchset adds support for retrieving TC flower statistics for
offloaded rules, which includes packets count, bytes count and last used
time stamp. Currently The statistics are gathered on a per-rule basis.
This patchset also includes generic allocator for counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add support for TC flower offload statistics
Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: Arkadi Sharshvesky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add support for generic flow counter allocation
Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Add support for counter allocator
Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.
The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.
Each module can add dedicated sub-pool or use existing one.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Mar 2017 06:43:20 +0000 (23:43 -0700)]
Merge branch 'nfp-xdp_adjust_head'
Jakub Kicinski says:
====================
nfp: XDP adjust head support
This series adds support for XDP adjust head. Bulk of the code
is actually just paying technical debt. On reconfiguration request
nfp was allocating new resources separately leaving device running
with the existing set of rings. We used to manage the new resources
in special ring set structures. This set is simply separating the
datapath part of the device structure from the control information
allowing the new datapath structure to be allocated with all new
memory and rings. The swap operation is now greatly simplified.
We also save a lot of parameter passing this way. Hopefully the churn
is worth the negative diffstat.
Support for XDP adjust head is done in a pretty standard way. NFP
is a bit special because it prepends metadata before packet data
so we have to do a bit of memcpying in case XDP will run. We also
luck out a little bit because the fact that we already have prepend
space allocated means that one byte is enough to store the extra XDP
space (256 of standard prepend space is a bit inconvenient since
it would normally require 16bits or boolean with additional shifts).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Mar 2017 18:38:39 +0000 (10:38 -0800)]
nfp: add support for xdp_adjust_head()
Support prepending data from XDP. We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP. In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Mar 2017 18:38:36 +0000 (10:38 -0800)]
nfp: validate rx offset from the BAR and size down it's field
NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom. This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Mar 2017 18:38:34 +0000 (10:38 -0800)]
nfp: switch to using data path structures for reconfiguration
Instead of passing around sets of rings and their parameters just
store all information in the data path structure.
We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing. This allows us
to simply assign the entire data path structures instead of copying
field by field.
The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Mar 2017 18:38:29 +0000 (10:38 -0800)]
nfp: pass new data path to ring reconfig
Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure. We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Mar 2017 18:38:27 +0000 (10:38 -0800)]
nfp: separate data path information from the reset of adapter structure
Move all data path information into a separate structure. This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Mar 2017 06:41:04 +0000 (23:41 -0700)]
Merge branch 'stmmac-multiqueue-mac-prep'
Joao Pinto says:
====================
prepare mac operations for multiple queues
As agreed with David Miller, this patch-set is the first of 3 to enable
multiple queues in stmmac.
This first one concentrates on mac operations adding functionalities as:
a) Configuration through DT
b) RX and TX scheduling algorithms programming
b) TX queues weight programming (essential in weightes algorithms)
c) RX enable as DCB or AVB (preparing for future AVB support)
d) Mapping RX queue to DMA channel
e) IRQ treatment prepared for multiple queues
f) Debug dump prepared for multiple queues
g) CBS configuration
In v3 patch-set version I included a new patch to enable CBS configuration
(Patch 9).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Joao Pinto [Fri, 10 Mar 2017 18:24:52 +0000 (18:24 +0000)]
net: stmmac: configure mtl rx and tx algorithms
This patch adds the RX and TX scheduling algorithms programming.
It introduces the multiple queues configuration function
(stmmac_mtl_configuration) in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joao Pinto [Fri, 10 Mar 2017 18:24:51 +0000 (18:24 +0000)]
net: stmmac: multiple queues dt configuration
This patch adds the multiple queues configuration in the Device Tree.
It was also created a set of structures to keep the RX and TX queues
configurations to be used in the driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Mar 2017 06:35:21 +0000 (23:35 -0700)]
Merge branch 'stmmac-tegra186'
Thierry Reding says:
====================
net: stmmac: Fixes and Tegra186 support
This series of patches start with a few cleanups that I ran across while
adding Tegra186 support to the stmmac driver. It then adds code for FIFO
size parsing from feature registers and finally enables support for the
incarnation of the Synopsys DWC QOS IP found on NVIDIA Tegra186 SoCs.
Thierry Reding [Fri, 10 Mar 2017 16:35:01 +0000 (17:35 +0100)]
net: stmmac: dwc-qos: Add Tegra186 support
The NVIDIA Tegra186 SoC contains an instance of the Synopsys DWC
ethernet QOS IP core. The binding that it uses is slightly different
from existing ones because of the integration (clocks, resets, ...).
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thierry Reding [Fri, 10 Mar 2017 16:35:00 +0000 (17:35 +0100)]
net: stmmac: dwc-qos: Split out ->probe() and ->remove()
Split out the binding specific parts of ->probe() and ->remove() to
enable the driver to support variants of the binding. This is useful in
order to keep backwards-compatibility while making it easy for a sub-
driver to deal only with the updated bindings rather than having to add
compatibility quirks all over the place.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com> Reviewed-By: Joao Pinto <jpinto@synopsys.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thierry Reding [Fri, 10 Mar 2017 16:34:58 +0000 (17:34 +0100)]
net: stmmac: Parse FIFO sizes from feature registers
New version of this core encode the FIFO sizes in one of the feature
registers. Use these sizes as default, but still allow device tree to
override them for backwards compatibility.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thierry Reding [Fri, 10 Mar 2017 16:34:53 +0000 (17:34 +0100)]
net: stmmac: Rename clk_ptp_ref clock to ptp_ref
There aren't currently any users of the "clk_ptp_ref", but there are
other references to "ptp_ref", so I'm leaning towards considering that a
typo. Fix it.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Bernat [Fri, 10 Mar 2017 15:30:24 +0000 (16:30 +0100)]
vxlan: use appropriate family on L3 miss
When sending a L3 miss, the family is set to AF_INET even for IPv6. This
causes userland (eg "ip monitor") to be confused. Ensure we send the
appropriate family in this case. For L2 miss, keep using AF_INET.
Signed-off-by: Vincent Bernat <vincent@bernat.im> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Fri, 10 Mar 2017 04:38:47 +0000 (12:38 +0800)]
net: Eliminate duplicated codes by creating one new function in_dev_select_addr
There are two duplicated loops codes which used to select right
address in current codes. Now eliminate these codes by creating
one new function in_dev_select_addr.
Signed-off-by: Gao Feng <fgao@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
sctp: add receiver-side procedures for stream reconf asoc reset and add streams and response
Patch 2/7, 4/7, 5/7, 6/7 are to implement the process of asoc reset request,
add streams requests and all kinds of responses.
Patch 1/7 and 3/7 are ahead of 2/7 and 4/7 to add two event notification
for asoc reset and add streams.
Patch 7/7 is the last patch for implementing rfc6525 sctp stream reconf
to add sysctl and sockopt interface for users to enable sctp stream reconf.
After this patchset, sctp stream reconf will be able to work as rfc6525.
v1->v2:
- put these into a smaller group.
- rename the titles of the commits and improve some changelogs.
- improve sctp_chunk_lookup_strreset_param and reuse it in patch 4/7.
- process addstrm outreq as the ack of in addstrm inreq if strreset_chunk
is not NULL in patch 4/7.
- remove the stream alloc when sending addstrm inreq, and the process in
peer will response it by sending a addstrm out request back in patch 5/7.
- adjust the process of addstrm in resp to fit in the codes that only alloc
streams through addstrm outreq in patch 6/7.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 10 Mar 2017 04:11:12 +0000 (12:11 +0800)]
sctp: add get and set sockopt for reconf_enable
This patchset is to add SCTP_RECONFIG_SUPPORTED sockopt, it would
set and get asoc reconf_enable value when asoc_id is set, or it
would set and get ep reconf_enalbe value if asoc_id is 0.
It is also to add sysctl interface for users to set the default
value for reconf_enable.
After this patch, stream reconf will work.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 10 Mar 2017 04:11:11 +0000 (12:11 +0800)]
sctp: implement receiver-side procedures for the Reconf Response Parameter
This patch is to implement Receiver-Side Procedures for the
Re-configuration Response Parameter in rfc6525 section 5.2.7.
sctp_process_strreset_resp would process the response for any
kind of reconf request, and the stream reconf is applied only
when the response result is success.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 10 Mar 2017 04:11:10 +0000 (12:11 +0800)]
sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter
This patch is to implement Receiver-Side Procedures for the Add Incoming
Streams Request Parameter described in rfc6525 section 5.2.6.
It is also to fix that it shouldn't have add streams when sending addstrm
in request, as the process in peer will handle it by sending a addstrm out
request back.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
VSR Burru [Fri, 10 Mar 2017 01:03:24 +0000 (17:03 -0800)]
liquidio: optimize DMA in NUMA systems
Optimize DMA in NUMA systems by allocating memory from NUMA node that NIC
is plugged in to; DMA will no longer cross NUMA nodes. If NIC IRQs are
pinned to a local CPU, that CPU's access to the DMA'd data is also
optimized.
Signed-off-by: VSR Burru <veerasenareddy.burru@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com> Signed-off-by: Satanand Burla <satananda.burla@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The code in netvsc_device_remove was incorrectly calling napi_disable
repeatedly on the same element. This would cause attempts
to remove netvsc module to hang.
Fixes: 2506b1dc4bbe ("netvsc: implement NAPI") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since rndis_halt_device waits until all outstanding sends and
receives are completed. Netvsc device needs to still schedule
NAPI to see those completions.
Fixes: 2506b1dc4bbe ("netvsc: implement NAPI") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Mar 2017 06:01:07 +0000 (23:01 -0700)]
Merge branch 'dpaa_eth-next' of git://git.freescale.com/ppc/upstream/linux
Madalin Bucur says:
====================
QorIQ DPAA 1 updates
This patch set introduces a series of fixes and features to the DPAA 1
drivers. Besides activating hardware Rx checksum offloading, four traffic
classes are added for Tx traffic prioritisation.
changes from v1: added patch to enable context-A stashing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv6: Add early demux handler for UDP unicast
While running a single stream UDPv6 test, we observed that amount
of CPU spent in NET_RX softirq was much greater than UDPv4 for an
equivalent receive rate. The test here was run on an ARM64 based
Android system. On further analysis with perf, we found that UDPv6
was spending significant time in the statistics netfilter targets
which did socket lookup per packet. These statistics rules perform
a lookup when there is no socket associated with the skb. Since
there are multiple instances of these rules based on UID, there
will be equal number of lookups per skb.
By introducing early demux for UDPv6, we avoid the redundant lookups.
This also helped to improve the performance (800Mbps -> 870Mbps) on a
CPU limited system in a single stream UDPv6 receive test with 1450
byte sized datagrams using iperf.
v1->v2: Use IPv6 cookie to validate dst instead of 0 as suggested
by Eric
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Kosina [Wed, 8 Mar 2017 15:03:32 +0000 (16:03 +0100)]
net: sched: make default fifo qdiscs appear in the dump
The original reason [1] for having hidden qdiscs (potential scalability
issues in qdisc_match_from_root() with single linked list in case of large
amount of qdiscs) has been invalidated by 59cc1f61f0 ("net: sched: convert
qdisc linked list to hashtable").
This allows us for bringing more clarity and determinism into the dump by
making default pfifo qdiscs visible.
We're not turning this on by default though, at it was deemed [2] too
intrusive / unnecessary change of default behavior towards userspace.
Instead, TCA_DUMP_INVISIBLE netlink attribute is introduced, which allows
applications to request complete qdisc hierarchy dump, including the
ones that have always been implicit/invisible.
Singleton noop_qdisc stays invisible, as teaching the whole infrastructure
about singletons would require quite some surgery with very little gain
(seeing no qdisc or seeing noop qdisc in the dump is probably setting
the same user expectation).
Philippe Reynes [Wed, 8 Mar 2017 22:41:04 +0000 (23:41 +0100)]
net: hyperv: use new api ethtool_{get|set}_link_ksettings
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Tested-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The first patch moves the core FIB notification code to a separate file,
so that code related to FIB rules is placed in fib_rules.c and not
fib_trie.c. The reason for the change will become even more apparent in
follow-up patchset where we extend the FIB rules notifications.
Second patch removes a redundant argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:56:19 +0000 (08:56 +0100)]
ipv4: fib: Remove redundant argument
We always pass the same event type to fib_notify() and
fib_rules_notify(), so we can safely drop this argument.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:56:18 +0000 (08:56 +0100)]
ipv4: fib: Move FIB notification code to a separate file
Most of the code concerned with the FIB notification chain currently
resides in fib_trie.c, but this isn't really appropriate, as the FIB
notification chain is also used for FIB rules.
Therefore, it makes sense to move the common FIB notification code to a
separate file and have it export the relevant functions, which can be
invoked by its different users (e.g., fib_trie.c, fib_rules.c).
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Mar 2017 17:36:07 +0000 (09:36 -0800)]
Merge branch 'mlxsw-vrf-offload-prep'
Jiri Pirko says:
====================
mlxsw: Preparations for VRF offload
Ido says:
This patchset aims to prepare the mlxsw driver for VRF offload. The
follow-up patchsets that introduce VRF support can be found here:
https://github.com/idosch/linux/tree/idosch-next
The first four patches are mainly concerned with the netdevice
notification block. There are no functional changes, but merely
restructuring to more easily integrate VRF enslavement.
Patches 5-10 remove various assumptions throughout the code about a
single virtual router (VR) and also restructure the internal data
structures to more accurately represent the device's operation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:43 +0000 (08:53 +0100)]
mlxsw: spectrum_router: Make abort mechanism VR-aware
When the abort mechanism is invoked it binds the first virtual router
(VR) to an LPM tree and inserts a default route to direct packets to the
CPU.
With VRFs, we can have router interfaces (RIFs) bound to multiple VRs,
so we need to make sure packets are trapped from all VRs and not just
the first one.
Upon abort invocation, bind all active VRs to the same LPM tree and
insert a default route in each.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:42 +0000 (08:53 +0100)]
mlxsw: spectrum_router: Explicitly Associate RIFs with VRs
Up until now we implicitly associated all the router interfaces (RIFs)
with the first virtual router (VR). This must be changed in order to
enable VRF offload. Otherwise, a packet received via a VRF slave would
do a FIB lookup in the same table used by other VRFs.
Instead, bind the RIF to a VR according to the table where FIB lookup
should be performed for packets received via the RIF.
Currently, we only care about the MAIN and LOCAL tables (which we squash
together).
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A virtual router (VR) is an entity within the device to which routing
tables and interfaces can be bound to. It can be used to implement VRFs.
In the initial implementation we associated the VR with a specific
protocol (e.g., IPv4) and an LPM tree. However, this isn't really
accurate, as the same VR can be used for both IPv4 and IPv6 traffic, by
binding a different LPM tree to a {VR, Proto} pair.
This patch aims to restructure the VR code according to the above logic,
so that VRs are more accurately represented by the driver's data
structures. The main motivation behind this change is to prepare the
driver for VRF offload.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:40 +0000 (08:53 +0100)]
mlxsw: spectrum_router: Simplify LPM tree allocation
When looking for a new LPM tree we should always consider all the unused
trees. It doesn't matter if the new tree is required due to changes in
currently used prefixes inside an existing routing table or because a
route was inserted into an empty table.
Both cases are functionally identical and therefore should be treated
the same.
When looking for a new LPM tree, consider all unused trees and don't
reserve trees for specific cases.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:39 +0000 (08:53 +0100)]
mlxsw: spectrum_router: Place RIF related code with router code
The inetaddr notification block is currently implemented in the main
driver file, but this isn't really appropriate, as it mainly creates and
destroys router interfaces (RIFs) which belong with the rest of the
router code.
This will become even more apparent later on when we'll need to bind
these RIFs to virtual routers according to the VRF's table.
Structure the driver better and prevent unnecessary function exports by
moving the RIF related code with the rest of the router code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:36 +0000 (08:53 +0100)]
mlxsw: spectrum: Associate PVID vPort with appropriate netdev
When a VLAN device is configured on top of a LAG device (f.e.,
bond0.10), a vPort is created on top of each of the LAG's slaves and its
'dev' pointer is set to the VLAN device.
This is in contrast to the implicit PVID vPort (representing 'bond0'),
whose 'dev' pointer keeps pointing to the port netdev itself (f.e.,
'sw1p1').
Make both cases consistent by setting their 'dev' pointer to the actual
netdev they represent. Either the LAG device itself (in the case of the
PVID vPort) or the VLAN device on top of it.
This will later allow us to more easily understand for which netdev we
should create the router interface (RIF) upon enslavement to a VRF
master.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:35 +0000 (08:53 +0100)]
mlxsw: spectrum: Don't assume upper device's type
When an upper device is configured on top of a vPort we make sure it's a
bridge master during PRECHANGEUPPER and fail otherwise. Therefore, when
CHANGEUPPER is later received we don't bother checking the upper's type.
Make the code more extendable in preparation for VRF uppers, by checking
the upper's type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Fri, 10 Mar 2017 07:53:34 +0000 (08:53 +0100)]
mlxsw: spectrum: Sanitize bridge's upper devices
We're going to allow bridges stacked on top of port netdevs to be
enslaved to a VRF, but for now, only VLAN uppers of the VLAN-aware
bridge are supported.
Sanitize any other bridge upper. This is consistent with the way we
sanitize port netdevs' uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-jammy-kernel.git / log