Jiri Slaby [Mon, 21 Jun 2010 15:02:40 +0000 (17:02 +0200)]
USB: gadget/printer, fix sleep inside atomic
Stanse found that sleep is called inside atomic context created by
lock_printer_io spinlock in several functions. It's used in process
context only and some functions sleep inside its critical section. As
this is not allowed for spinlocks, switch it to mutex.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Craig W. Nadler <craig@nadler.us> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jiri Slaby [Mon, 21 Jun 2010 15:02:51 +0000 (17:02 +0200)]
USB: isp1362-hcd, fix double lock
Stanse found that isp1362_sw_reset tries to take a isp1362_hcd->lock,
but it is already held in isp1362_hc_stop. Avoid that by introducing
__isp1362_sw_reset which doesn't take the lock and call it from
isp1362_hc_stop. isp1362_sw_reset is then as simple as lock --
__isp1362_sw_reset -- unlock.
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 18 Jun 2010 14:16:33 +0000 (10:16 -0400)]
USB: fix oops in usb_sg_init()
This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference. An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
In the change by 749da5f82fe33ff68dd4aa1a5e35cd9aa6246dab,
The change in the status when the USB device is connected is wrong.
Therefore, the device is not recognized.
Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> CC: Paul Mundt" <lethal@linux-sh.org> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Thu, 10 Jun 2010 19:25:28 +0000 (12:25 -0700)]
USB: xHCI: Fix bug in link TRB activation change.
Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for
control transfers. The patch was supposed to change when the link TRBs at
the end of each ring segment were given to the hardware. If a transfer
descriptor (TD) ended just before the link TRB, the code wouldn't give
back the link TRB to the hardware; instead it would be given back in
prepare_ring() just before the next TD was enqueued at the top of the
ring.
Unfortunately, the code relied on checking the chain bit of the TRB to
determine whether the TD ended just before the link TRB. It assumed that
the ring enqueuing code would call prepare_ring() before enqueuing the
next TD. However, control transfers are made of multiple TDs, and
prepare_ring() is only called once before enqueuing two or three TDs.
If the first or second TD of the control transfer ended just before the
link TRB, then the code in inc_enq() would not move the enqueue pointer
past the link TRB, and the link TRB would get overwritten. This would
cause the xHCI driver to start writing to memory past the ring segment,
and eventually the system would crash or hang.
The fix is to add a flag to inc_enq() that says whether the caller will
enqueue more TDs before calling prepare_ring(). If the chain bit is
cleared (meaning this is the last TRB in a TD), and the caller will not
enqueue more TDs, then we defer giving back the link TRB.
USB: gadget: g_fs: possible invalid pointer reference bug fixed
During __gfs_do_config() some invalid pointers may be left
in usb_configuration::interfaces array from previous calls
to the __gfs_do_config() for the same configuration. This
will always happen if an user space function which has
a fewer then the last user space function registers itself.
Composite's set_config() function that a pointer after the
last interface in usb_configuration::interface is NULL
unless the array is full.
This patch makes the __gfs_do_config() make sure that if the
usb_configuration::interface is not full then a pointer
after the last interface is NULL.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Mon, 28 Jun 2010 05:56:32 +0000 (22:56 -0700)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md/raid5: don't include 'spare' drives when reshaping to fewer devices.
md/raid5: add a missing 'continue' in a loop.
md/raid5: Allow recovered part of partially recovered devices to be in-sync
md/raid5: More careful check for "has array failed".
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
md/raid5: avoid oops when number of devices is reduced then increased.
md: enable raid4->raid0 takeover
md: clear layout after ->raid0 takeover
md: fix raid10 takeover: use new_layout for setup_conf
md: fix handling of array level takeover that re-arranges devices.
md: raid10: Fix null pointer dereference in fix_read_error()
Restore partition detection of newly created md arrays.
Linus Torvalds [Sun, 27 Jun 2010 18:33:44 +0000 (11:33 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix first chunk match in per_cpu_ptr_to_phys()
percpu: fix trivial bugs in pcpu_build_alloc_info()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (52 commits)
phylib: Add autoload support for the LXT973 phy.
ISDN: hysdn, fix potential NULL dereference
vxge: fix memory leak in vxge_alloc_msix() error path
isdn/gigaset: correct CAPI connection state storage
isdn/gigaset: encode HLC and BC together
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
isdn/gigaset: correct CAPI voice connection encoding
isdn/gigaset: honor CAPI application's buffer size request
cpmac: do not leak struct net_device on phy_connect errors
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
ipv6: fix NULL reference in proxy neighbor discovery
Bluetooth: Bring back var 'i' increment
xfrm: check bundle policy existance before dereferencing it
sky2: enable rx/tx in sky2_phy_reinit()
cnic: Disable statistics initialization for eth clients that do not support statistics
net: add dependency on fw class module to qlcnic and netxen_nic
snmp: fix SNMP_ADD_STATS()
hso: remove setting of low_latency flag
udp: Fix bogus UFO packet generation
lasi82596: fix netdev_mc_count conversion
...
Linus Torvalds [Sun, 27 Jun 2010 16:04:02 +0000 (09:04 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix an embarassing typo in encode_attrs()
NFSv4: Ensure that /proc/self/mountinfo displays the minor version number
NFSv4.1: Ensure that we initialise the session when following a referral
SUNRPC: Fix a re-entrancy bug in xs_tcp_read_calldir()
nfs4 use mandatory attribute file type in nfs4_get_root
Linus Torvalds [Sun, 27 Jun 2010 15:03:00 +0000 (08:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
MAINTAINERS - Add an entry for the input MT protocol
Input: wacom - fix serial number handling on Cintiq 21UX2
Input: fixup X86_MRST selects
Input: sysrq - fix "stuck" SysRq mode
Input: ad7877 - fix spi word size to 16 bit
Input: pcf8574_keypad - fix off by one in pcf8574_kp_irq_handler()
Linus Torvalds [Sun, 27 Jun 2010 14:50:47 +0000 (07:50 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
ext3: update ctime when changing the file's permission by setfacl
ext2: update ctime when changing the file's permission by setfacl
Linus Torvalds [Sun, 27 Jun 2010 14:39:57 +0000 (07:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: usb/endpoint, fix dangling pointer use
ALSA: asihpi - Get rid of incorrect "long" types and casts.
ASoC: DaVinci: Fix McASP hardware FIFO configuration
ALSA: hda - Fix line-in for mb5 model MacBook (Pro) 5,1 / 5,2
ALSA: usb-audio: fix UAC2 control value queries
ALSA: usb-audio: parse UAC2 sample rate ranges correctly
ALSA: usb-audio: fix control messages for USB_RECIP_INTERFACE
ALSA: usb-audio: add check for faulty clock in parse_audio_format_rates_v2()
ALSA: hda - Don't check capture source mixer if no ADC is available
Linus Torvalds [Sun, 27 Jun 2010 14:39:38 +0000 (07:39 -0700)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (k8temp) Bypass core swapping on single-core processors
hwmon: (i5k_amb) Fix sysfs attribute for lockdep
hwmon: (k10temp) Do not blacklist known working CPU models
Linus Torvalds [Sun, 27 Jun 2010 14:37:51 +0000 (07:37 -0700)]
Merge git://git.infradead.org/iommu-2.6
* git://git.infradead.org/iommu-2.6:
intel-iommu: Force-disable IOMMU for iGFX on broken Cantiga revisions.
intel-iommu: Fix double lock in get_domain_for_dev()
intel-iommu: Fix reference by physical address in intel_iommu_attach_device()
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
MAINTAINERS: change mailing list address for CIFS
cifs: remove bogus first_time check in NTLMv2 session setup code
cifs: don't call cifs_new_fileinfo unless cifs_open succeeds
cifs: don't ignore cifs_posix_open_inode_helper return value
cifs: clean up arguments to cifs_open_inode_helper
cifs: pass instantiated filp back after open call
cifs: move cifs_new_fileinfo call out of cifs_posix_open
cifs: implement drop_inode superblock op
cifs: don't attempt busy-file rename unless it's in same directory
Linus Torvalds [Sun, 27 Jun 2010 14:30:25 +0000 (07:30 -0700)]
Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/5200: fix lite5200 ethernet phy address
powerpc/5200: Fix build error in sound code.
powerpc/5200: fix oops during going to standby
powerpc/5200: add lite5200 onboard I2C eeprom and flash
maintainers: Add git trees for SPI and device tree
of: Drop properties with "/" in their name
Linus Torvalds [Sun, 27 Jun 2010 14:29:19 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: Fix de2104x driver failing to readout MAC address correctly
alpha: Detect Super IO chip, no IDE on Avanti, enable EPP19
alpha: fix pci_mmap_resource API breakage
alpha: fix __arch_hweight32 typo
Linus Torvalds [Sun, 27 Jun 2010 14:15:53 +0000 (07:15 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix mpic_resume on early G5 macs
powerpc: rtas_flash needs to use rtas_data_buf
powerpc: Unconditionally enabled irq stacks
powerpc/kexec: Wait for online/possible CPUs only.
powerpc: Disable CONFIG_SYSFS_DEPRECATED
powerpc/boot: Remove addRamdisk.c since it is now unused
powerpc: Move kdump default base address to 64MB on 64bit
powerpc: Remove dead CONFIG_HIGHPTE
powerpc/fsl-booke: Move loadcam_entry back to asm code to fix SMP ftrace
powerpc/fsl-booke: Fix InstructionTLBError execute permission check
Linus Torvalds [Sun, 27 Jun 2010 14:05:02 +0000 (07:05 -0700)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
kbuild: fix LOCALVERSION handling to match description
kbuild: Fix modpost segfault
Linus Torvalds [Sun, 27 Jun 2010 14:03:12 +0000 (07:03 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / PM: Do not enable GPEs for system wakeup in advance
ACPICA: Truncate I/O addresses to 16 bits for Windows compatibility
ACPICA: Limit maximum time for Sleep() operator
ACPICA: Fix namestring associated with AE_NO_HANDLER exception
ACPI / ACPICA: Fix sysfs GPE interface
ACPI / ACPICA: Fix GPE initialization
ACPI / ACPICA: Avoid writing full enable masks to GPE registers
ACPI / ACPICA: Fix low-level GPE manipulation code
ACPI / ACPICA: Use helper function for computing GPE masks
ACPI / ACPICA: Do not attempt to disable GPE when installing handler
ACPI: Disable Vista compatibility for Sony VGN-NS50B_L
ACPI: fan: fix unbalanced code block
ACPI: Store NVS state even when entering suspend to RAM
suspend: Move NVS save/restore code to generic suspend functionality
ACPI: Do not try to set up acpi processor stuff on cores exceeding maxcpus=
ACPI: acpi_pad: Don't needlessly mark LAPIC unstable
Dan Carpenter [Fri, 11 Jun 2010 16:30:05 +0000 (17:30 +0100)]
KEYS: Propagate error code instead of returning -EINVAL
This is from a Smatch check I'm writing.
strncpy_from_user() returns -EFAULT on error so the first change just
silences a warning but doesn't change how the code works.
The other change is a bug fix because install_thread_keyring_to_cred()
can return a variety of errors such as -EINVAL, -EEXIST, -ENOMEM or
-EKEYREVOKED.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Tue, 22 Jun 2010 01:41:36 +0000 (01:41 +0000)]
ISDN: hysdn, fix potential NULL dereference
Stanse found that lp is dereferenced earlier than checked for being
NULL in hysdn_rx_netpkt. Move the initialization below the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:55:20 +0000 (13:55 +0000)]
isdn/gigaset: correct CAPI connection state storage
CAPI applications can handle several connections in parallel,
so one connection state per application isn't sufficient.
Store the connection state in the channel structure instead.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Mon, 21 Jun 2010 13:55:05 +0000 (13:55 +0000)]
isdn/gigaset: encode HLC and BC together
Adapt to buggy device firmware which accepts setting HLC only in the
same command line as BC, by encoding HLC and BC in a single command
if both are specified, and rejecting HLC without BC.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
The Gigaset CAPI driver handled all DATA_B3_REQ messages as if the
Delivery Confirmation flag bit was set, delaying the emission of the
DATA_B3_CONF reply until the data was actually transmitted. Some
CAPI applications (notably Asterisk) aren't happy with that
behaviour. Change it to actually evaluate the Delivery Confirmation
flag as described the CAPI specification.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Gigaset CAPI driver select L2_VOICE (AT^SBPR=2) as the
layer 2 encoding for transparent connections, like the ISDN4Linux
variant. L2_BITSYNC (AT^SBPR=0) mutes internal connections and
distorts external ones.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the Gigaset CAPI driver to limit the length of a connection's
payload data receive buffers to the corresponding CAPI application's
data buffer size, as some real-life CAPI applications tend to be
rather unhappy if they receive bigger data blocks than requested.
Impact: bugfix Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Sat, 19 Jun 2010 15:24:27 +0000 (15:24 +0000)]
smc91c92_cs: fix the problem that lan & modem does not work simultaneously
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: fix NULL reference in proxy neighbor discovery
The addition of TLLAO option created a kernel OOPS regression
for the case where neighbor advertisement is being sent via
proxy path. When using proxy, ipv6_get_ifaddr() returns NULL
causing the NULL dereference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Henrik Rydberg [Fri, 25 Jun 2010 02:10:40 +0000 (19:10 -0700)]
MAINTAINERS - Add an entry for the input MT protocol
This patch adds a maintainer for the input multitouch (MT) protocol,
such that get_maintainer.pl selects it whenever an MT event is present
in the patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Timo Teräs [Thu, 24 Jun 2010 21:35:00 +0000 (14:35 -0700)]
xfrm: check bundle policy existance before dereferencing it
Fix the bundle validation code to not assume having a valid policy.
When we have multiple transformations for a xfrm policy, the bundle
instance will be a chain of bundles with only the first one having
the policy reference. When policy_genid is bumped it will expire the
first bundle in the chain which is equivalent of expiring the whole
chain.
Reported-bisected-and-tested-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
NeilBrown [Thu, 17 Jun 2010 07:48:26 +0000 (17:48 +1000)]
md/raid5: don't include 'spare' drives when reshaping to fewer devices.
There are few situations where it would make any sense to add a spare
when reducing the number of devices in an array, but it is
conceivable: A 6 drive RAID6 with two missing devices could be
reshaped to a 5 drive RAID6, and a spare could become available
just in time for the reshape, but not early enough to have been
recovered first. 'freezing' recovery can make this easy to
do without any races.
However doing such a thing is a bad idea. md will not record the
partially-recovered state of the 'spare' and when the reshape
finished it will think that the spare is still spare.
Easiest way to avoid this confusion is to simply disallow it.
NeilBrown [Thu, 17 Jun 2010 07:41:03 +0000 (17:41 +1000)]
md/raid5: add a missing 'continue' in a loop.
As the comment says, the tail of this loop only applies to devices
that are not fully in sync, so if In_sync was set, we should avoid
the rest of the loop.
This bug will hardly ever cause an actual problem. The worst it
can do is allow an array to be assembled that is dirty and degraded,
which is not generally a good idea (without warning the sysadmin
first).
This will only happen if the array is RAID4 or a RAID5/6 in an
intermediate state during a reshape and so has one drive that is
all 'parity' - no data - while some other device has failed.
This is certainly possible, but not at all common.
NeilBrown [Thu, 17 Jun 2010 07:25:21 +0000 (17:25 +1000)]
md/raid5: Allow recovered part of partially recovered devices to be in-sync
During a recovery of reshape the early part of some devices might be
in-sync while the later parts are not.
We we know we are looking at an early part it is good to treat that
part as in-sync for stripe calculations.
This is particularly important for a reshape which suffers device
failure. Treating the data as in-sync can mean the difference between
data-safety and data-loss.
NeilBrown [Wed, 16 Jun 2010 07:17:53 +0000 (17:17 +1000)]
md/raid5: More careful check for "has array failed".
When we are reshaping an array, the device failure combinations
that cause us to decide that the array as failed are more subtle.
In particular, any 'spare' will be fully in-sync in the section
of the array that has already been reshaped, thus failures that
affect only that section are less critical.
So encode this subtlety in a new function and call it as appropriate.
The case that showed this problem was a 4 drive RAID5 to 8 drive RAID6
conversion where the last two devices failed.
This resulted in:
good good good good incomplete good good failed failed
while converting a 5-drive RAID6 to 8 drive RAID5
The incomplete device causes the whole array to look bad,
bad as it was actually good for the section that had been
converted to 8-drives, all the data was actually safe.
Reported-by: Terry Morris <tbmorris@tbmorris.com> Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown [Wed, 16 Jun 2010 07:01:25 +0000 (17:01 +1000)]
md: Don't update ->recovery_offset when reshaping an array to fewer devices.
When an array is reshaped to have fewer devices, the reshape proceeds
from the end of the devices to the beginning.
If a device happens to be non-In_sync (which is possible but rare)
we would normally update the ->recovery_offset as the reshape
progresses. However that would be wrong as the recover_offset records
that the early part of the device is in_sync, while in fact it would
only be the later part that is in_sync, and in any case the offset
number would be measured from the wrong end of the device.
Relatedly, if after a reshape a spare is discovered to not be
recoverred all the way to the end, not allow spare_active
to incorporate it in the array.
This becomes relevant in the following sample scenario:
A 4 drive RAID5 is converted to a 6 drive RAID6 in a combined
operation.
The RAID5->RAID6 conversion will cause a 5 drive to be included as a
spare, then the 5drive -> 6drive reshape will effectively rebuild that
spare as it progresses. The 6th drive is treated as in_sync the whole
time as there is never any case that we might consider reading from
it, but must not because there is no valid data.
If we interrupt this reshape part-way through and reverse it to return
to a 5-drive RAID6 (or event a 4-drive RAID5), we don't want to update
the recovery_offset - as that would be wrong - and we don't want to
include that spare as active in the 5-drive RAID6 when the reversed
reshape completed and it will be mostly out-of-sync still.
NeilBrown [Wed, 16 Jun 2010 06:45:16 +0000 (16:45 +1000)]
md/raid5: avoid oops when number of devices is reduced then increased.
The entries in the stripe_cache maintained by raid5 are enlarged
when we increased the number of devices in the array, but not
shrunk when we reduce the number of devices.
So if entries are added after reducing the number of devices, we
much ensure to initialise the whole entry, not just the part that
is currently relevant. Otherwise if we enlarge the array again,
we will reference uninitialised values.
As grow_buffers/shrink_buffer now want to use a count that is stored
explicity in the raid_conf, they should get it from there rather than
being passed it as a parameter.
NeilBrown [Tue, 15 Jun 2010 08:36:03 +0000 (09:36 +0100)]
md: fix handling of array level takeover that re-arranges devices.
Most array level changes leave the list of devices largely unchanged,
possibly causing one at the end to become redundant.
However conversions between RAID0 and RAID10 need to renumber
all devices (except 0).
This renumbering is currently being done in the ->run method when the
new personality takes over. However this is too late as the common
code in md.c might already have invalidated some of the devices if
they had a ->raid_disk number that appeared to high.
Moving it into the ->takeover method is too early as the array is
still active at that time and wrong ->raid_disk numbers could cause
confusion.
So add a ->new_raid_disk field to mdk_rdev_s and use it to communicate
the new raid_disk number.
Now the common code knows exactly which devices need to be renumbered,
and which can be invalidated, and can do it all at a convenient time
when the array is suspend.
It can also update some symlinks in sysfs which previously were not be
updated correctly.
Reported-by: Maciej Trela <maciej.trela@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
md: raid10: Fix null pointer dereference in fix_read_error()
Such NULL pointer dereference can occur when the driver was fixing the
read errors/bad blocks and the disk was physically removed
causing a system crash. This patch check if the
rcu_dereference() returns valid rdev before accessing it in fix_read_error().
Cc: stable@kernel.org Signed-off-by: Prasanna S. Panchamukhi <prasanna.panchamukhi@riverbed.com> Signed-off-by: Rob Becker <rbecker@riverbed.com> Signed-off-by: NeilBrown <neilb@suse.de>
The logic was almost right. However if revalidate_disk is called
when the device is not yet open, bdev->bd_disk won't be set, so the
flush_disk() Call will not set bd_invalidated.
So when md_open is called we still need to ensure that
->bd_invalidated gets set. This is easily done with a call to
check_disk_size_change in the place where the offending commit removed
check_disk_change. At the important times, the size will have changed
from 0 to non-zero, so check_disk_size_change will set bd_invalidated.
Brandon Philips [Wed, 16 Jun 2010 16:21:58 +0000 (16:21 +0000)]
sky2: enable rx/tx in sky2_phy_reinit()
sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.
However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:
$ ethtool -r eth0
$ ethtool -A eth0 autoneg off
Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.
Signed-off-by: Brandon Philips <bphilips@suse.de> Tested-by: Brandon Philips <bphilips@suse.de> Cc: stable@kernel.org Tested-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: add dependency on fw class module to qlcnic and netxen_nic
netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
virtio-pci resets the device at startup by writing to the status
register, but this does not clear the pci config space,
specifically msi enable status which affects register
layout.
This breaks things like kdump when they try to use e.g. virtio-blk.
Fix by forcing msi off at startup. Since pci.c already has
a routine to do this, we export and use it instead of duplicating code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Vivek Goyal <vgoyal@redhat.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: linux-pci@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org
add_buf returns ring size on out of memory,
this is not what devices expect.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: stable@kernel.org # .34.x
Randy Dunlap [Fri, 18 Jun 2010 05:31:17 +0000 (22:31 -0700)]
Input: fixup X86_MRST selects
Some of the recent X86_MRST additions make some "select"s
conditional on X86_MRST but missed some related kconfig symbols,
causing:
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ab2): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_end_command':
(.text+0x257ae1): undefined reference to `i8042_unlock_chip'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b40): undefined reference to `i8042_check_port_owner'
drivers/built-in.o: In function `ps2_begin_command':
(.text+0x257b6f): undefined reference to `i8042_lock_chip'
when SERIO_I8042=m, SERIO_LIBPS2=y, KEYBOARD_ATKBD=y.
We need to make i8042 dependant upon !X86_MRST and allow deselecting
atkbd on Moorestown even when !CONFIG_EMBEDDED.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Jacob Pan <jacob.jun.pan@intel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Trond Myklebust [Wed, 16 Jun 2010 17:57:32 +0000 (13:57 -0400)]
SUNRPC: Fix a re-entrancy bug in xs_tcp_read_calldir()
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
Filip Aben [Tue, 22 Jun 2010 17:10:35 +0000 (10:10 -0700)]
hso: remove setting of low_latency flag
This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.
Signed-off-by: Filip Aben <f.aben@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 15 Jun 2010 01:52:25 +0000 (01:52 +0000)]
udp: Fix bogus UFO packet generation
It has been reported that the new UFO software fallback path
fails under certain conditions with NFS. I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU. The software fallback path simply discards these packets.
This patch fixes the problem by not generating such packets on
the UFO path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Mon, 21 Jun 2010 03:44:50 +0000 (03:44 +0000)]
NET: MIPSsim: Fix modpost warning.
$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]
Fixed by making mipsnet_probe __devinit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/mipsnet.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-) Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Mon, 21 Jun 2010 15:03:21 +0000 (17:03 +0200)]
ALSA: usb/endpoint, fix dangling pointer use
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Jean Delvare [Sun, 20 Jun 2010 07:22:32 +0000 (09:22 +0200)]
hwmon: (k8temp) Bypass core swapping on single-core processors
Commit a2e066bba2aad6583e3ff648bf28339d6c9f0898 introduced core
swapping for CPU models 64 and later. I recently had a report about
a Sempron 3200+, model 95, for which this patch broke temperature
reading. It happens that this is a single-core processor, so the
effect of the swapping was to read a temperature value for a core
that didn't exist, leading to an incorrect value (-49 degrees C.)
Disabling core swapping on singe-core processors should fix this.
Additional comment from Andreas:
The BKDG says
Thermal Sensor Core Select (ThermSenseCoreSel)-Bit 2. This bit
selects the CPU whose temperature is reported in the CurTemp
field. This bit only applies to dual core processors. For
single core processors CPU0 Thermal Sensor is always selected.
k8temp_probe() correctly detected that SEL_CORE can't be used on single
core CPU. Thus k8temp did never update the temperature values stored
in temp[1][x] and -49 degrees was reported. For single core CPUs we
must use the values read into temp[0][x].
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Rick Moritz <rhavin@gmx.net> Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: stable@kernel.org
i5k_amb.ko uses dynamically allocated memory (by kmalloc) for
attributes passed to sysfs. So, sysfs_attr_init() should be called
for working happy with lockdep.
Jean Delvare [Sun, 20 Jun 2010 07:22:31 +0000 (09:22 +0200)]
hwmon: (k10temp) Do not blacklist known working CPU models
When detecting AM2+ or AM3 socket with DDR2, only blacklist cores
which are known to exist in AM2+ format.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Clemens Ladisch <clemens@ladisch.de> Cc: Andreas Herrmann <andreas.herrmann3@amd.com> Cc: stable@kernel.org
Bob Copeland [Fri, 18 Jun 2010 17:15:23 +0000 (13:15 -0400)]
ath5k: initialize ah->ah_current_channel
ath5k assumes ah_current_channel is always a valid pointer in
several places, but a newly created interface may not have a
channel. To avoid null pointer dereferences, set it up to point
to the first available channel until later reconfigured.
This fixes the following oops:
$ rmmod ath5k
$ insmod ath5k
$ iw phy0 set distance 11000
Cc: stable@kernel.org Reported-by: Steve Brown <sbrown@cortland.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c7f486567c1d0acd2e4166c47069835b9f75e77b
(PCI PM: PCIe PME root port service driver) causes the native PCIe
PME signaling to be used by default, if the BIOS allows the kernel to
control the standard configuration registers of PCIe root ports.
However, the native PCIe PME is coupled to the native PCIe hotplug
and calling pcie_pme_acpi_setup() makes some BIOSes expect that
the native PCIe hotplug will be used as well. That, in turn, causes
problems to appear on systems where the PCIe hotplug driver is not
loaded. The usual symptom, as reported by Jaroslav Kameník and
others, is that the ACPI GPE associated with PCIe hotplug keeps
firing continuously causing kacpid to take substantial percentage
of CPU time.
To work around this issue, change the default so that the native
PCIe PME signaling is only used if directly requested with the help
of the pcie_pme= command line switch.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15924 , which is
a listed regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reported-by: Jaroslav Kameník <jaroslav@kamenik.cz> Tested-by: Antoni Grzymala <antekgrzymala@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tejun Heo [Fri, 18 Jun 2010 09:44:31 +0000 (11:44 +0200)]
percpu: fix first chunk match in per_cpu_ptr_to_phys()
per_cpu_ptr_to_phys() determines whether the passed in @addr belongs
to the first_chunk or not by just matching the address against the
address range of the base unit (unit0, used by cpu0). When an adress
from another cpu was passed in, it will always determine that the
address doesn't belong to the first chunk even when it does. This
makes the function return a bogus physical address which may lead to
crash.
This problem was discovered by Cliff Wickman while investigating a
crash during kdump on a SGI UV system.
It is common in end-node, non STP bridges to set forwarding
delay to zero; which causes the forwarding database cleanup
to run every clock tick. Change to run only as soon as needed
or at next ageing timer interval which ever is sooner.
Use round_jiffies_up macro rather than attempting round up
by changing value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI / PM: Do not enable GPEs for system wakeup in advance
After commit 9630bdd9b15d2f489c646d8bc04b60e53eb5ec78
(ACPI: Use GPE reference counting to support shared GPEs) the wakeup
enable mask bits of GPEs are set as soon as the GPEs are enabled to
wake up the system. Unfortunately, this leads to a regression
reported by Michal Hocko, where a system is woken up from ACPI S5 by
a device that is not supposed to do that, because the wakeup enable
mask bit of this device's GPE is always set when
acpi_enter_sleep_state() calls acpi_hw_enable_all_wakeup_gpes(),
although it should only be set if the device is supposed to wake up
the system from the target state.
To work around this issue, rework the ACPI power management code so
that GPEs are not enabled to wake up the system upfront, but only
during a system state transition when the target state of the system
is known. [Of course, this means that the reference counting of
"wakeup" GPEs doesn't really make sense and it is sufficient to
set/unset the wakeup mask bits for them during system sleep
transitions. This will allow us to simplify the GPE handling code
quite a bit, but that change is too intrusive for 2.6.35.]
FUJITA Tomonori [Thu, 17 Jun 2010 15:56:05 +0000 (08:56 -0700)]
bnx2: fix dma_get_ops compilation breakage
This removes dma_get_ops() prefetch optimization in bnx2.
bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.
But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.
This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.
[ Remove now unused local variable 'pdev' -DaveM ]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log