With the current default values for Rx path i.e., 8 queues of 8Kb entries
each with 4Kb size, interface will consume 256Mb for Rx. The default values
causing the driver probe to fail when the system memory is low. Based on
the perforamnce results, rx-ring count value of 1Kb gives the comparable
performance with Rx coalesce timeout of 12 seconds. Updating the default
values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qede: Loopback implementation should ignore the normal traffic
During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration is not supported for 100G adapters.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qede: get_channels() need to populate max tx/rx coalesce values
Recent changes in kernel ethtool implementation requires the driver
callback for get_channels() has to populate the values for max tx/rx
coalesce fields.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Thu, 20 Oct 2016 21:19:46 +0000 (14:19 -0700)]
ipv4: use the right lock for ping_group_range
This reverts commit a681574c99be23e4d20b769bf0e543239c364af5
("ipv4: disable BH in set_ping_group_range()") because we never
read ping_group_range in BH context (unlike local_port_range).
Then, since we already have a lock for ping_group_range, those
using ip_local_ports.lock for ping_group_range are clearly typos.
We might consider to share a same lock for both ping_group_range
and local_port_range w.r.t. space saving, but that should be for
net-next.
Fixes: a681574c99be ("ipv4: disable BH in set_ping_group_range()") Fixes: ba6b918ab234 ("ping: move ping_group_range out of CONFIG_SYSCTL") Cc: Eric Dumazet <edumazet@google.com> Cc: Eric Salo <salo@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 21 Oct 2016 21:21:56 +0000 (14:21 -0700)]
net: dsa: bcm_sf2: Do not rely on kexec_in_progress
After discussing with Eric, it turns out that, while using
kexec_in_progress is a nice optimization, which prevents us from always
powering on the integrated PHY, let's just turn it on in the shutdown
path.
This removes a dependency on kexec_in_progress which, according to Eric
should not be used by modules
Fixes: 2399d6143f85 ("net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 21 Oct 2016 21:21:55 +0000 (14:21 -0700)]
Revert "kexec: Export kexec_in_progress to modules"
This reverts commit 97dcaa0fcfd24daa9a36c212c1ad1d5a97759212. Based on
the review discussion with Eric, we will come up with a different fix
for the bcm_sf2 driver which does not make it rely on the
kexec_in_progress value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Sat, 22 Oct 2016 01:49:14 +0000 (21:49 -0400)]
netns: revert "netns: avoid disabling irq for netns id"
This reverts commit bc51dddf98c9 ("netns: avoid disabling irq for
netns id") as it was found to cause problems with systems running
SELinux/audit, see the mailing list thread below:
Eventually we should be able to reintroduce this code once we have
rewritten the audit multicast code to queue messages much the same
way we do for unicast messages. A tracking issue for this can be
found below:
Reported-by: Stephen Smalley <sds@tycho.nsa.gov> Reported-by: Elad Raz <e@eladraz.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 87e9f0315952
("ipv4: fix a potential deadlock in mcast getsockopt() path")
this is due to we still have a case, ipv6_sock_mc_close(),
where we acquire sk_lock before rtnl_lock. Close this deadlock
with the similar solution, that is always acquire rtnl lock first.
Fixes: baf606d9c9b1 ("ipv4,ipv6: grab rtnl before locking the socket") Reported-by: Baozeng Ding <sploving1@gmail.com> Tested-by: Baozeng Ding <sploving1@gmail.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix compilation warning in xt_hashlimit on m68k 32-bits, from
Geert Uytterhoeven.
2) Fix wrong timeout in set elements added from packet path via
nft_dynset, from Anders K. Pedersen.
3) Remove obsolete nf_conntrack_events_retry_timeout sysctl
documentation, from Nicolas Dichtel.
4) Ensure proper initialization of log flags via xt_LOG, from
Liping Zhang.
5) Missing alias to autoload ipcomp, also from Liping Zhang.
6) Missing NFTA_HASH_OFFSET attribute validation, again from Liping.
7) Wrong integer type in the new nft_parse_u32_check() function,
from Dan Carpenter.
8) Another wrong integer type declaration in nft_exthdr_init, also
from Dan Carpenter.
9) Fix insufficient mode validation in nft_range.
10) Fix compilation warning in nft_range due to possible uninitialized
value, from Arnd Bergmann.
11) Zero nf_hook_ops allocated via xt_hook_alloc() in x_tables to
calm down kmemcheck, from Florian Westphal.
12) Schedule gc_worker() to run again if GC_MAX_EVICTS quota is reached,
from Nicolas Dichtel.
13) Fix nf_queue() after conversion to single-linked hook list, related
to incorrect bypass flag handling and incorrect hook point of
reinjection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 21 Oct 2016 01:15:16 +0000 (18:15 -0700)]
kexec: Export kexec_in_progress to modules
The bcm_sf2 driver uses kexec_in_progress to know whether it can power
down an integrated PHY during shutdown, and can be built as a module.
Other modules may be using this in the future, so export it.
Fixes: 2399d6143f85 ("net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 20 Oct 2016 17:26:48 +0000 (10:26 -0700)]
ipv4: disable BH in set_ping_group_range()
In commit 4ee3bd4a8c746 ("ipv4: disable BH when changing ip local port
range") Cong added BH protection in set_local_port_range() but missed
that same fix was needed in set_ping_group_range()
Fixes: b8f1a55639e6 ("udp: Add function to make source port for UDP tunnels") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Eric Salo <salo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 20 Oct 2016 16:32:19 +0000 (09:32 -0700)]
net: dsa: bcm_sf2: Prevent GPHY shutdown for kexec'd kernels
For a kernel that is being kexec'd we re-enable the integrated GPHY in
order for the subsequent MDIO bus scan to succeed and properly bind to
the bcm7xxx PHY driver. If we did not do that, the GPHY would be shut
down by the time the MDIO driver is probing the bus, and it would fail
to read the correct PHY OUI and therefore bind to an appropriate PHY
driver. Later on, this would cause DSA not to be able to successfully
attach to the PHY, and the interface would not be created at all.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Oct 2016 15:13:53 +0000 (17:13 +0200)]
bpf, test: fix ld_abs + vlan push/pop stress test
After commit 636c2628086e ("net: skbuff: Remove errornous length
validation in skb_vlan_pop()") mentioned test case stopped working,
throwing a -12 (ENOMEM) return code. The issue however is not due to 636c2628086e, but rather due to a buggy test case that got uncovered
from the change in behaviour in 636c2628086e.
The data_size of that test case for the skb was set to 1. In the
bpf_fill_ld_abs_vlan_push_pop() handler bpf insns are generated that
loop with: reading skb data, pushing 68 tags, reading skb data,
popping 68 tags, reading skb data, etc, in order to force a skb
expansion and thus trigger that JITs recache skb->data. Problem is
that initial data_size is too small.
While before 636c2628086e, the test silently bailed out due to the
skb->len < VLAN_ETH_HLEN check with returning 0, and now throwing an
error from failing skb_ensure_writable(). Set at least minimum of
ETH_HLEN as an initial length so that on first push of data, equivalent
pop will succeed.
Fixes: 4d9c5c53ac99 ("test_bpf: add bpf_skb_vlan_push/pop() tests") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 20 Oct 2016 13:58:02 +0000 (15:58 +0200)]
net: add recursion limit to GRO
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039 Fixes: 9b174d88c257 ("net: Add Transparent Ethernet Bridging GRO support.") Fixes: 66e5133f19e9 ("vlan: Add GRO support for non hardware accelerated vlan") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Jiri Benc <jbenc@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The check for an underflow of tmp_prefered_lft is always false
because tmp_prefered_lft is unsigned. The intention of the check
was to guard against racing with an update of the
temp_prefered_lft sysctl, potentially resulting in an underflow.
As suggested by David Miller, the best way to prevent the race is
by reading the sysctl variable using READ_ONCE.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Reported-by: Julia Lawall <julia.lawall@lip6.fr> Fixes: 76506a986dc3 ("IPv6: fix DESYNC_FACTOR") Signed-off-by: David S. Miller <davem@davemloft.net>
nf_queue handling is broken since e3b37f11e6e4 ("netfilter: replace
list_head with single linked list") for two reasons:
1) If the bypass flag is set on, there are no userspace listeners and
we still have more hook entries to iterate over, then jump to the
next hook. Otherwise accept the packet. On nf_reinject() path, the
okfn() needs to be invoked.
2) We should not re-enter the same hook on packet reinjection. If the
packet is accepted, we have to skip the current hook from where the
packet was enqueued, otherwise the packets gets enqueued over and
over again.
This restores the previous list_for_each_entry_continue() behaviour
happening from nf_iterate() that was dealing with these two cases.
This patch introduces a new nf_queue() wrapper function so this fix
becomes simpler.
Fixes: e3b37f11e6e4 ("netfilter: replace list_head with single linked list") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
It makes sense to display the descriptors even if
DES0 is zero. This helps for example in case of it
is needed to dump rx write-back descriptors to get
timestamp status.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Oct 2016 15:23:08 +0000 (11:23 -0400)]
Merge branch 'ncsi-fixes'
Gavin Shan says:
====================
net/ncsi: More bug fixes
This series fixes 2 issues that were found during NCSI's availability
testing on BCM5718 and improves HNCDSC AEN handler:
* PATCH[1] refactors the code so that minimal code change is put
to PATCH[2].
* PATCH[2] fixes the NCSI channel's stale link state before doing
failover.
* PATCH[3] chooses the hot channel, which was ever chosen as active
channel, when the available channels are all in link-down state.
* PATCH[4] improves Host Network Controller Driver Status Change
(HNCDSC) AEN handler
Changelog
=========
v2:
* Merged PATCH[v1 1/2] to PATCH[v2 1].
* Avoid if/else statements in ncsi_suspend_channel() as Joel suggested.
* Added comments to explain why we need retrieve last link states in
ncsi_suspend_channel().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan [Thu, 20 Oct 2016 00:45:52 +0000 (11:45 +1100)]
net/ncsi: Improve HNCDSC AEN handler
This improves AEN handler for Host Network Controller Driver Status
Change (HNCDSC):
* The channel's lock should be hold when accessing its state.
* Do failover when host driver isn't ready.
* Configure channel when host driver becomes ready.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan [Thu, 20 Oct 2016 00:45:51 +0000 (11:45 +1100)]
net/ncsi: Choose hot channel as active one if necessary
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. C0 is in link-up state while C1 is in link-down
state. C0 is chosen as active channel until unplugging and plugging
C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN
packet received on C0 to report link-down event. After that, C1 is
chosen as active channel. LSC AEN for link-up event is lost on C0
when plugging C0's cable back. We lose the network even C0 is usable.
This resolves the issue by recording the (hot) channel that was ever
chosen as active one. The hot channel is chosen to be active one
if none of available channels in link-up state. With this, C0 is still
the active one after unplugging C0's cable. LSC AEN packet received
on C0 when plugging its cable back.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan [Thu, 20 Oct 2016 00:45:50 +0000 (11:45 +1100)]
net/ncsi: Fix stale link state of inactive channels on failover
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. Both of them are connected to different LANs,
means they are in link-up state and C0 is chosen as the active one
until resetting BCM5718 happens as below.
Resetting BCM5718 results in LSC (Link State Change) AEN packet
received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet
received on C0 to report link-down, it fails over to C1 because C1
is in link-up state as software can see. However, C1 is in link-down
state in hardware. It means the link state is out of synchronization
between hardware and software, resulting in inappropriate channel (C1)
selected as active one.
This resolves the issue by sending separate GLS (Get Link Status)
commands to all channels in the package before trying to do failover.
The last link states of all channels in the package are retrieved.
With it, C0 (not C1) is selected as active one as expected.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan [Thu, 20 Oct 2016 00:45:49 +0000 (11:45 +1100)]
net/ncsi: Avoid if statements in ncsi_suspend_channel()
There are several if/else statements in the state machine implemented
by switch/case in ncsi_suspend_channel() to avoid duplicated code. It
makes the code a bit hard to be understood.
This drops if/else statements in ncsi_suspend_channel() to improve the
code readability as Joel Stanley suggested. Also, it becomes easy to
add more states in the state machine without affecting current code.
No logical changes introduced by this.
Suggested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 19 Oct 2016 14:42:39 +0000 (17:42 +0300)]
net/sched: act_mirred: Use passed lastuse argument
stats_update callback is called by NIC drivers doing hardware
offloading of the mirred action. Lastuse is passed as argument
to specify when the stats was actually last updated and is not
always the current time.
Fixes: 9798e6fe4f9b ('net: act_mirred: allow statistic updates from offloaded actions') Signed-off-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 20 Oct 2016 14:05:45 +0000 (16:05 +0200)]
mlxsw: pci: Fix reset wait for SwitchX2
SwitchX2 firmware does not implement reset done yet. Moreover, when
busy-polled for ready magic, that slows down firmware and reset takes
longer than the defined timeout, causing initialization to fail.
So restore the previous behaviour and just sleep in this case.
Fixes: 233fa44bd67a ("mlxsw: pci: Implement reset done check") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Thu, 20 Oct 2016 14:05:44 +0000 (16:05 +0200)]
mlxsw: switchx2: Fix ethernet port initialization
When creating an ethernet port fails, we must move the port to disable,
otherwise putting the port in switch partition 0 (ETH) or 1 (IB) will
always fails.
Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support") Signed-off-by: Elad Raz <eladr@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 20 Oct 2016 14:05:43 +0000 (16:05 +0200)]
mlxsw: spectrum_router: Make mlxsw_sp_router_fib4_del return void and remove warn
The function return value is not checked anywhere. Also, the warning
causes huge slowdown when removing large number of FIB entries which
were not offloaded, because of ordering issue. Ido's preparing
a patchset to fix the ordering issue, but that is definitelly not
net tree material.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 20 Oct 2016 14:05:42 +0000 (16:05 +0200)]
mlxsw: spectrum_router: Use correct tree index for binding
By a mistake, there is tree index 0 passed to RALTB. Should be
MLXSW_SP_LPM_TREE_MIN.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls") Reported-by: Yotam Gigi <yotamg@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit commit 7086605a6ab5 ("stmmac: fix error check when init ptp")
breaks the procedure added by the
commit efee95f42b5d ("ptp_clock: future-proofing drivers against PTP
subsystem becoming optional")
So this patch tries to re-import the logic added by the latest
commit above: it makes sense to have the stmmac_ptp_register
as void function and, inside the main, the stmmac_init_ptp can fails
in case of the capability cannot be supported by the HW.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre TORGUE <alexandre.torgue@st.com> Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Nicolas Pitre <nico@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This warning is harmless; we copy 'uninitialized' data from the hook ops
but it will not be used.
Long term the structures keeping run-time data should be disentangled
from those only containing config-time data (such as where in the list
to insert a hook), but thats -next material.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de> Suggested-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Aaron Conole <aconole@bytheb.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jiri Pirko [Tue, 18 Oct 2016 16:59:34 +0000 (18:59 +0200)]
rtnetlink: Add rtnexthop offload flag to compare mask
The offload flag is a status flag and should not be used by
FIB semantics for comparison.
Fixes: 37ed9493699c ("rtnetlink: add RTNH_F_EXTERNAL flag for fib offload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that the 8021q module propagates the call to
ndo_bridge_getlink() via switchdev ops, but the switch driver doesn't
recognize the netdev, as it's not offloaded.
While we can ignore calls being made to non-bridge ports inside the
driver, a better fix would be to push this check up to the switchdev
layer.
Note that these ndos can be called for non-bridged netdev, but this only
happens in certain PF drivers which don't call the corresponding
switchdev functions anyway.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Tested-by: Tamir Winetroub <tamirw@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that netdev_all_lower_get_next_rcu() never advances the
iterator, thereby causing the loop over the lower adjacency list to run
forever.
Fix this by advancing the iterator and avoid the infinite loop.
Fixes: 7ce856aaaf13 ("mlxsw: spectrum: Add couple of lower device helper functions") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Garver [Mon, 17 Oct 2016 20:30:12 +0000 (16:30 -0400)]
flow_dissector: Check skb for VLAN only if skb specified.
Fixes a panic when calling eth_get_headlen(). Noticed on i40e driver.
Fixes: d5709f7ab776 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci") Signed-off-by: Eric Garver <e@erig.me> Reviewed-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Amir Vadai <amir@vadai.me> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 17 Oct 2016 15:17:51 +0000 (15:17 +0000)]
qed: Use list_move_tail instead of list_del/list_add_tail
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 17 Oct 2016 22:16:15 +0000 (00:16 +0200)]
rocker: fix maybe-uninitialized warning
In some rare configurations, we get a warning about the 'index' variable
being used without an initialization:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function ‘ofdpa_port_fib_ipv4.isra.16.constprop’:
drivers/net/ethernet/rocker/rocker_ofdpa.c:2425:92: warning: ‘index’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is a false positive, the logic is just a bit too complex for gcc
to follow here. Moving the intialization of 'index' a little further
down makes it clear to gcc that the function always returns an error
if it is not initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 17 Oct 2016 22:16:09 +0000 (00:16 +0200)]
net/hyperv: avoid uninitialized variable
The hdr_offset variable is only if we deal with a TCP or UDP packet,
but as the check surrounding its usage tests for skb_is_gso()
instead, the compiler has no idea if the variable is initialized
or not at that point:
drivers/net/hyperv/netvsc_drv.c: In function ‘netvsc_start_xmit’:
drivers/net/hyperv/netvsc_drv.c:494:42: error: ‘hdr_offset’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds an additional check for the transport type, which
tells the compiler that this path cannot happen. Since the
get_net_transport_info() function should always be inlined
here, I don't expect this to result in additional runtime
checks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
gcc found a reference to an uninitialized variable in the error handling
of bcm_enet_open, introduced by a recent cleanup:
drivers/net/ethernet/broadcom/bcm63xx_enet.c: In function 'bcm_enet_open'
drivers/net/ethernet/broadcom/bcm63xx_enet.c:1129:2: warning: 'phydev' may be used uninitialized in this function [-Wmaybe-uninitialized]
This makes the use of that variable conditional, so we only reference it
here after it has been used before. Unlike my normal patches, I have not
build-tested this one, as I don't currently have mips test in my
randconfig setup.
Fixes: 625eb8667d6f ("net: ethernet: broadcom: bcm63xx: use phydev from struct net_device") Cc: Philippe Reynes <tremyfr@gmail.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Mon, 17 Oct 2016 20:28:10 +0000 (15:28 -0500)]
ibmvnic: Update MTU after device initialization
It is possible for the MTU to be changed during the initialization
process with the VNIC Server. Ensure that the net device is updated
to reflect the new MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: multicast: restore perm router ports on multicast enable
Satish reported a problem with the perm multicast router ports not getting
reenabled after some series of events, in particular if it happens that the
multicast snooping has been disabled and the port goes to disabled state
then it will be deleted from the router port list, but if it moves into
non-disabled state it will not be re-added because the mcast snooping is
still disabled, and enabling snooping later does nothing.
Here are the steps to reproduce, setup br0 with snooping enabled and eth1
added as a perm router (multicast_router = 2):
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
<empty>
At this point we have mcast enabled and eth1 as a perm router (value = 2)
but it is not in the router list which is incorrect.
After this change:
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
router ports on br0: eth1
Note: we can directly do br_multicast_enable_port for all because the
querier timer already has checks for the port state and will simply
expire if it's in blocking/disabled. See the comment added by
commit 9aa66382163e7 ("bridge: multicast: add a comment to
br_port_state_selection about blocking state")
Fixes: 561f1103a2b7 ("bridge: Add multicast_snooping sysfs toggle") Reported-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added nft_range_eval() function handles the two possible
nft range operations, but as the compiler warning points out,
any unexpected value would lead to the 'mismatch' variable being
used without being initialized:
net/netfilter/nft_range.c: In function 'nft_range_eval':
net/netfilter/nft_range.c:45:5: error: 'mismatch' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This removes the variable in question and instead moves the
condition into the switch itself, which is potentially more
efficient than adding a bogus 'default' clause as in my
first approach, and is nicer than using the 'uninitialized_var'
macro.
Fixes: 0f3cd9b36977 ("netfilter: nf_tables: add range expression") Link: http://patchwork.ozlabs.org/patch/677114/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tobias Klauser [Tue, 18 Oct 2016 09:22:54 +0000 (11:22 +0200)]
tcp: Remove unused but set variable
Remove the unused but set variable icsk in listening_get_next to fix the
following GCC warning when building with 'W=1':
net/ipv4/tcp_ipv4.c: In function ‘listening_get_next’:
net/ipv4/tcp_ipv4.c:1890:31: warning: variable ‘icsk’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Tue, 18 Oct 2016 08:51:25 +0000 (14:21 +0530)]
cxgb4: Fix number of queue sets corssing the limit
Do not let number of offload queue sets to go more than
MAX_OFLD_QSETS, which would otherwise crash the driver
on machines with cores more than MAX_OFLD_QSETS.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Tue, 18 Oct 2016 07:20:55 +0000 (09:20 +0200)]
dwc_eth_qos: enable flow control by default
Allow autoneg to enable flow control by default.
The behavior when autoneg is off has not changed.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Jesper Nilsson <jespern@axis.com> Acked-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Tue, 18 Oct 2016 07:20:33 +0000 (09:20 +0200)]
dwc_eth_qos: do not clear pause flags from phy_device->supported
phy_device->supported is originally set by the PHY driver.
The ethernet driver should filter phy_device->supported to only contain
flags supported by the IP.
The IP supports setting rx and tx flow control independently,
therefore SUPPORTED_Pause and SUPPORTED_Asym_Pause should not be cleared.
If the flags are cleared, pause frames cannot be enabled (even if they
are supported by the PHY).
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: Jesper Nilsson <jespern@axis.com> Acked-by: Lars Persson <larper@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Tue, 18 Oct 2016 07:07:29 +0000 (09:07 +0200)]
net/hsr: Remove unused but set variable
Remove the unused but set variable master_dev in check_local_dest to fix
the following GCC warning when building with 'W=1':
net/hsr/hsr_forward.c: In function ‘check_local_dest’:
net/hsr/hsr_forward.c:303:21: warning: variable ‘master_dev’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Oct 2016 14:26:15 +0000 (10:26 -0400)]
Merge tag 'mac80211-for-davem-2016-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This is relatively small, mostly to get the SG/crypto
from stack removal fix that crashes things when VMAP
stack is used in conjunction with software crypto.
Aside from that, we have:
* a fix for AP_VLAN usage with the nl80211 frame command
* two fixes (and two preparation patches) for A-MSDU, one
to discard group-addressed (multicast) and unexpected
4-address A-MSDUs, the other to validate A-MSDU inner
MAC addresses properly to prevent controlled port bypass
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Tue, 18 Oct 2016 06:16:03 +0000 (08:16 +0200)]
bnx2: fix locking when netconsole is used
Functions bnx2_reg_rd_ind(), bnx2_reg_wr_ind() and bnx2_ctx_wr()
can be called with IRQs disabled when netconsole is enabled. So they
should use spin_{,un}lock_irq{save,restore} instead of _bh variants.
Cc: Sony Chacko <sony.chacko@qlogic.com> Cc: Dept-HSGLinuxNICDev@qlogic.com Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Oct 2016 17:03:04 +0000 (13:03 -0400)]
Merge branch 'net-driver-autoload'
Javier Martinez Canillas says:
====================
net: Fix module autoload for several platform drivers
I noticed that module autoload won't be working in a bunch of platform
drivers in the net subsystem and this patch series contains the fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Fix module autoload for OF registration
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/dsa/bcm_sf2.ko | grep alias
alias: platform:brcm-sf2
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/dsa/b53/b53_mmap.ko | grep alias
$
net: hisilicon: Fix hns_mdio module autoload for OF registration
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/ethernet/hisilicon//hns_mdio.ko | grep alias
alias: platform:Hi-HNS_MDIO
alias: acpi*:HISI0141:*
net: qcom/emac: Fix module autoload for OF registration
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/ethernet/qualcomm/emac/qcom-emac.ko | grep alias
alias: platform:qcom-emac
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns: Fix hns_dsaf module autoload for OF registration
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/ethernet/hisilicon/hns/hns_dsaf.ko | grep alias
alias: acpi*:HISI00B2:*
alias: acpi*:HISI00B1:*
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ $ modinfo drivers/net/ethernet/aurora/nb8800.ko | grep alias
$
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Mans Rullgard <mans@mansr.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/net/ethernet/ezchip/nps_enet.ko | grep alias
$
After this patch:
$ modinfo drivers/net/ethernet/ezchip/nps_enet.ko | grep alias
alias: of:N*T*Cezchip,nps-mgt-enetC*
alias: of:N*T*Cezchip,nps-mgt-enet
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use nft_parse_u32_check() to make sure we don't get a value over the
unsigned 8-bit integer. Moreover, make sure this value doesn't go over
the two supported range comparison modes.
Dan Carpenter [Wed, 12 Oct 2016 06:09:12 +0000 (09:09 +0300)]
netfilter: nft_exthdr: fix error handling in nft_exthdr_init()
"err" needs to be signed for the error handling to work.
Fixes: 36b701fae12a ('netfilter: nf_tables: validate maximum value of u32 netlink attributes') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dan Carpenter [Wed, 12 Oct 2016 09:14:29 +0000 (12:14 +0300)]
netfilter: nf_tables: underflow in nft_parse_u32_check()
We don't want to allow negatives here.
Fixes: 36b701fae12a ('netfilter: nf_tables: validate maximum value of u32 netlink attributes') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Liping Zhang [Wed, 12 Oct 2016 13:09:22 +0000 (21:09 +0800)]
netfilter: xt_ipcomp: add "ip[6]t_ipcomp" module alias name
Otherwise, user cannot add related rules if xt_ipcomp.ko is not loaded:
# iptables -A OUTPUT -p 108 -m ipcomp --ipcompspi 1
iptables: No chain/target/match by that name.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Justin and Chris spotted that iptables NFLOG target was broken when they
upgraded the kernel to 4.8: "ulogd-2.0.5- IPs are no longer logged" or
"results in segfaults in ulogd-2.0.5".
Because "struct nf_loginfo li;" is a local variable, and flags will be
filled with garbage value, not inited to zero. So if it contains 0x1,
packets will not be logged to the userspace anymore.
Fixes: 7643507fe8b5 ("netfilter: xt_NFLOG: nflog-range does not truncate packets") Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com> Reported-by: Chris Caputo <ccaputo@alt.net> Tested-by: Chris Caputo <ccaputo@alt.net> Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nft_dynset: fix element timeout for HZ != 1000
With HZ=100 element timeout in dynamic sets (i.e. flow tables) is 10 times
higher than configured.
Add proper conversion to/from jiffies, when interacting with userspace.
I tested this on Linux 4.8.1, and it applies cleanly to current nf and
nf-next trees.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Anders K. Pedersen <akp@cohaesio.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: xt_hashlimit: Add missing ULL suffixes for 64-bit constants
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
net/netfilter/xt_hashlimit.c: In function ‘user2credits’:
net/netfilter/xt_hashlimit.c:476: warning: integer constant is too large for ‘long’ type
...
net/netfilter/xt_hashlimit.c:478: warning: integer constant is too large for ‘long’ type
...
net/netfilter/xt_hashlimit.c:480: warning: integer constant is too large for ‘long’ type
...
net/netfilter/xt_hashlimit.c: In function ‘rateinfo_recalc’:
net/netfilter/xt_hashlimit.c:513: warning: integer constant is too large for ‘long’ type
Fixes: 11d5f15723c9f39d ("netfilter: xt_hashlimit: Create revision 2 to support higher pps rates") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Vishwanath Pai <vpai@akamai.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Dumazet [Sat, 15 Oct 2016 15:50:49 +0000 (17:50 +0200)]
net: pktgen: remove rcu locking in pktgen_change_name()
After Jesper commit back in linux-3.18, we trigger a lockdep
splat in proc_create_data() while allocating memory from
pktgen_change_name().
This patch converts t->if_lock to a mutex, since it is now only
used from control path, and adds proper locking to pktgen_change_name()
1) pktgen_thread_lock to protect the outer loop (iterating threads)
2) t->if_lock to protect the inner loop (iterating devices)
Note that before Jesper patch, pktgen_change_name() was lacking proper
protection, but lockdep was not able to detect the problem.
Fixes: 8788370a1d4b ("pktgen: RCU-ify "if_list" to remove lock in next_to_run()") Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 17 Oct 2016 03:02:52 +0000 (20:02 -0700)]
net: Require exact match for TCP socket lookups if dif is l3mdev
Currently, socket lookups for l3mdev (vrf) use cases can match a socket
that is bound to a port but not a device (ie., a global socket). If the
sysctl tcp_l3mdev_accept is not set this leads to ack packets going out
based on the main table even though the packet came in from an L3 domain.
The end result is that the connection does not establish creating
confusion for users since the service is running and a socket shows in
ss output. Fix by requiring an exact dif to sk_bound_dev_if match if the
skb came through an interface enslaved to an l3mdev device and the
tcp_l3mdev_accept is not set.
skb's through an l3mdev interface are marked by setting a flag in
inet{6}_skb_parm. The IPv6 variant is already set; this patch adds the
flag for IPv4. Using an skb flag avoids a device lookup on the dif. The
flag is set in the VRF driver using the IP{6}CB macros. For IPv4, the
inet_skb_parm struct is moved in the cb per commit 971f10eca186, so the
match function in the TCP stack needs to use TCP_SKB_CB. For IPv6, the
move is done after the socket lookup, so IP6CB is used.
The flags field in inet_skb_parm struct needs to be increased to add
another flag. There is currently a 1-byte hole following the flags,
so it can be expanded to u16 without increasing the size of the struct.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Mon, 17 Oct 2016 14:05:33 +0000 (15:05 +0100)]
mac80211: move struct aead_req off the stack
Some crypto implementations (such as the generic CCM wrapper in crypto/)
use scatterlists to map fields of private data in their struct aead_req.
This means these data structures cannot live in the vmalloc area, which
means that they cannot live on the stack (with CONFIG_VMAP_STACK.)
This currently occurs only with the generic software implementation, but
the private data and usage is implementation specific, so move the whole
data structures off the stack into heap by allocating every time we need
to use them.
In addition, take care not to put any of our own stack allocations into
scatterlists. This involves reserving some extra room when allocating the
aead_request structures, and referring to those allocations in the scatter-
lists (while copying the data from the stack before the crypto operation)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
vmxnet3: avoid assumption about invalid dma_pa in vmxnet3_set_mc()
vmxnet3_set_mc() checks new_table_pa returned by dma_map_single()
with dma_mapping_error(), but even there it assumes zero is invalid pa
(it assumes dma_mapping_error(...,0) returns true if new_table is NULL).
The patch adds an explicit variable to track status of new_table_pa.
Found by Linux Driver Verification project (linuxtesting.org).
v2: use "bool" and "true"/"false" for boolean variables. Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 14 Oct 2016 19:26:11 +0000 (22:26 +0300)]
stmmac: fix an error code in stmmac_ptp_register()
PTR_ERR(NULL) is success. We have to preserve the error code earlier.
Fixes: 7086605a6ab5 ("stmmac: fix error check when init ptp") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Fri, 14 Oct 2016 19:14:35 +0000 (14:14 -0500)]
net: qcom/emac: disable interrupts before calling phy_disconnect
There is a race condition that can occur if EMAC interrupts are
enabled when phy_disconnect() is called. phy_disconnect() sets
adjust_link to NULL. When an interrupt occurs, the ISR might
call phy_mac_interrupt(), which wakes up the workqueue function
phy_state_machine(). This function might reference adjust_link,
thereby causing a null pointer exception.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Fri, 14 Oct 2016 13:40:33 +0000 (14:40 +0100)]
r8169: set coherent DMA mask as well as streaming DMA mask
PCI devices that are 64-bit DMA capable should set the coherent
DMA mask as well as the streaming DMA mask. On some architectures,
these are managed separately, and so the coherent DMA mask will be
left at its default value of 32 if it is not set explicitly. This
results in errors such as
on systems without memory that is 32-bit addressable by PCI devices.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Thu, 13 Oct 2016 23:43:16 +0000 (16:43 -0700)]
net: asix: Avoid looping when the device does not respond
Check answers from USB stack and avoid re-sending the request
multiple times if the device does not respond.
This fixes the following problem, observed with a probably flaky adapter.
[62108.732707] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[62108.914421] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[62108.914463] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[62108.914476] usb 1-3: Product: AX88x72A
[62108.914486] usb 1-3: Manufacturer: ASIX Elec. Corp.
[62108.914495] usb 1-3: SerialNumber: 000001
[62114.109109] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
[62114.109139] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to send software reset: ffffff92
[62119.109048] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
...
Since the USB timeout is 5 seconds, and the operation is retried 30 times,
this results in
Jesse Brandeburg [Thu, 13 Oct 2016 23:13:55 +0000 (16:13 -0700)]
ethtool: silence warning on bit loss
Sparse was complaining when we went to prototype some code
using ethtool_cmd_speed_set and SPEED_100000, which uses
the upper 16 bits of __u32 speed for the first time.
CHECK
...
.../uapi/linux/ethtool.h:123:28: warning:
cast truncates bits from constant value (186a0 becomes 86a0)
The warning is actually bogus, as no bits are really lost, but
we can get rid of the sparse warning with this one small change.
Reported-by: Preethi Banala <preethi.banala@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Brenden Blanco [Thu, 13 Oct 2016 20:13:11 +0000 (13:13 -0700)]
net/mlx4_en: fixup xdp tx irq to match rx
In cases where the number of tx rings is not a multiple of the number of
rx rings, the tx completion event will be handled on a different core
from the transmit and population of the ring. Races on the ring will
lead to a double-free of the page, and possibly other corruption.
The rings are initialized by default with a valid multiple of rings,
based on the number of cpus, therefore an invalid configuration requires
ethtool to change the ring layout. For instance 'ethtool -L eth0 rx 9 tx
8' will cause packets received on rx0, and XDP_TX'd to tx48, to be
completed on cpu3 (48 % 9 == 3).
Resolve this discrepancy by shifting the irq for the xdp tx queues to
start again from 0, modulo rx_ring_num.
Fixes: 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support") Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Brenden Blanco <bblanco@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Oct 2016 15:07:23 +0000 (11:07 -0400)]
Merge branch 'qed-fixes'
Yuval Mintz says:
====================
qed: Fix dependencies and warnings series
The first patch in this series follows Dan Carpenter's reports about
Smatch warnings for recent qed additions and fixes those.
The second patch is the most significant one [and the reason this is
ntended for 'net'] - it's based on Arnd Bermann's suggestion for fixing
compilation issues that were introduced with the roce addition as a result
of certain combinations of qed, qede and qedr Kconfig options.
The third follows the discussion with Arnd and clears a lot of the warnings
that arise when compiling the drivers with "C=1".
Please consider applying this series to 'net'.
====================
Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 13 Oct 2016 19:57:03 +0000 (22:57 +0300)]
qed: Additional work toward cleaning C=1
This cleans many of the warnings that would arise in qed as a
result of compilations with C=1; Most of those are the addition
of missing 'static' to functions, although there are several other
fixes as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 13 Oct 2016 19:57:02 +0000 (22:57 +0300)]
qed*: Fix Kconfig dependencies with INFINIBAND_QEDR
The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.
To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.
Fixes: cee9fbd8e2e9 ("qede: add qedr framework") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 13 Oct 2016 19:57:01 +0000 (22:57 +0300)]
qed: Fix static checker warning.
Smatch compains about qed_roce_ll2_tx() dereference
of the 'cdev' variable while testing its validity later.
As the validation checking is an over-kill [variable would always
be set], simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: abd49676c707 ("qed: Add RoCE ll2 & GSI support") Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Bohac [Thu, 13 Oct 2016 16:52:15 +0000 (18:52 +0200)]
IPv6: fix DESYNC_FACTOR
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Bohac [Thu, 13 Oct 2016 16:50:02 +0000 (18:50 +0200)]
IPv6: Drop the temporary address regen_timer
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 13 Oct 2016 16:26:56 +0000 (18:26 +0200)]
IB/ipoib: move back IB LL address into the hard header
After the commit 9207f9d45b0a ("net: preserve IP control block
during GSO segmentation"), the GSO CB and the IPoIB CB conflict.
That destroy the IPoIB address information cached there,
causing a severe performance regression, as better described here:
This change moves the data cached by the IPoIB driver from the
skb control lock into the IPoIB hard header, as done before
the commit 936d7de3d736 ("IPoIB: Stop lying about hard_header_len
and use skb->cb to stash LL addresses").
In order to avoid GRO issue, on packet reception, the IPoIB driver
stash into the skb a dummy pseudo header, so that the received
packets have actually a hard header matching the declared length.
To avoid changing the connected mode maximum mtu, the allocated
head buffer size is increased by the pseudo header length.
After this commit, IPoIB performances are back to pre-regression
value.
v2 -> v3: rebased
v1 -> v2: avoid changing the max mtu, increasing the head buf size
Fixes: 9207f9d45b0a ("net: preserve IP control block during GSO segmentation") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/networking: update git urls to use https over http
This fixes the following errors when trying to clone the urls:
Cloning into 'net'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/davem/net.git/' not found
Cloning into 'net-next'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/davem/net-next.git/' not found
Cloning into 'linux'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/' not found
Cloning into 'stable-queue'...
fatal: repository 'http://git.kernel.org/cgit/linux/kernel/git/stable/stable-queue.git/' not found
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: wan: slic_ds26522: Allow driver to built if COMPILE_TEST is enabled
The driver only has runtime but no build time dependency with FSL_SOC ||
ARCH_MXC || ARCH_LAYERSCAPE. So it can be built for testing purposes if
the COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: wan: slic_ds26522: Export OF module alias information
When the device is registered via OF, the OF table is used to match the
driver instead of the SPI device ID table, but the entries in the later
are used as aliasses to load the module if the driver was not built-in.
This is because the SPI core always reports an SPI module alias instead
of an OF one, but that could change so it's better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: wan: slic_ds26522: add SPI device ID table to fix module autoload
If the driver is built as a module, module alias information isn't filled
so the module won't be autoloaded. Add a SPI device ID table and use the
MODULE_DEVICE_TABLE() macro so the information is exported in the module.
Before this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
$
After this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
alias: spi:ds26522
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Wed, 12 Oct 2016 08:10:40 +0000 (10:10 +0200)]
ipv6: correctly add local routes when lo goes up
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed9c ("net IPv6 : Fix broken IPv6 routing table after loopback down-up") Fixes: a881ae1f625c ("ipv6: don't call addrconf_dst_alloc again when enable lo") Fixes: 33d99113b110 ("ipv6: reallocate addrconf router for ipv6 address when lo device up") Reported-by: Francesco Santoro <francesco.santoro@6wind.com> Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com> CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Weilong Chen <chenweilong@huawei.com> CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Fedorenko [Tue, 11 Oct 2016 19:47:20 +0000 (22:47 +0300)]
ip6_tunnel: fix ip6_tnl_lookup
The commit ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel
endpoints.") introduces support for wildcards in tunnels endpoints,
but in some rare circumstances ip6_tnl_lookup selects wrong tunnel
interface relying only on source or destination address of the packet
and not checking presence of wildcard in tunnels endpoints. Later in
ip6_tnl_rcv this packets can be dicarded because of difference in
ipproto even if fallback device have proper ipproto configuration.
This patch adds checks of wildcard endpoint in tunnel avoiding such
behavior
Fixes: ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel endpoints.") Signed-off-by: Vadim Fedorenko <junk@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix various build warnings in tlan/qed/xen-netback drivers, from
Arnd Bergmann.
2) Propagate proper error code in strparser's strp_recv(), from Geert
Uytterhoeven.
3) Fix accidental broadcast of RTM_GETTFILTER responses, from Eric
Dumazret.
4) Need to use list_for_each_entry_safe() in qed driver, from Wei
Yongjun.
5) Openvswitch 802.1AD bug fixes from Jiri Benc.
6) Cure BUILD_BUG_ON() in mlx5 driver, from Tom Herbert.
7) Fix UDP ipv6 checksumming in netvsc driver, from Stephen Hemminger.
8) stmmac driver fixes from Giuseppe CAVALLARO.
9) Fix access to mangled IP6CB in tcp, from Eric Dumazet.
10) Fix info leaks in tipc and rtnetlink, from Dan Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: bridge: add the multicast_flood flag attribute to brport_attrs
net: axienet: Remove unused parameter from __axienet_device_reset
liquidio: CN23XX: fix a loop timeout
net: rtnl: info leak in rtnl_fill_vfinfo()
tipc: info leak in __tipc_nl_add_udp_addr()
net: ipv4: Do not drop to make_route if oif is l3mdev
net: phy: Trigger state machine on state change and not polling.
ipv6: tcp: restore IP6CB for pktoptions skbs
netvsc: Remove mistaken udp.h inclusion.
xen-netback: fix type mismatch warning
stmmac: fix error check when init ptp
stmmac: fix ptp init for gmac4
qed: fix old-style function definition
netvsc: fix checksum on UDP IPV6
net_sched: reorder pernet ops and act ops registrations
xen-netback: fix guest Rx stall detection (after guest Rx refactor)
drivers/ptp: Fix kernel memory disclosure
net/mlx5: Add MLX5_ARRAY_SET64 to fix BUILD_BUG_ON
qmi_wwan: add support for Quectel EC21 and EC25
openvswitch: add NETIF_F_HW_VLAN_STAG_TX to internal dev
...
projects / mirror_ubuntu-hirsute-kernel.git / log