scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.
This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program. Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.
This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().
The problem trace is:
1) ipr_scsi_done() // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start() // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense() // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
// so set DID_PASSTHROUGH.
4) scsi_decide_disposition() // check for DID_PASSTHROUGH and return
// early on, faking a DID_OK.. *instead*
// of reaching scsi_check_sense().
// Had it reached the latter, that would
// set host_byte to DID_MEDIUM_ERROR.
5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte() // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error() // And that is checked in dm-mpath :: noretry_error()
// which would cause fail_path() not to be called.
With this patch applied, the I/O is failed but the paths are not. This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).
# dmesg
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
[...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
[...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
[...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
[...] blk_update_request: critical medium error, dev sdaf, sector 0
[...] blk_update_request: critical medium error, dev dm-6, sector 0
[...] Buffer I/O error on dev dm-6, logical block 0, async page read
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.
This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.
Fixes: 5c63f7f710bd ("aacraid: Added EEH support") Cc: stable@vger.kernel.org # v4.6+ Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Reviewed-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: sd: Fix capacity calculation with 32-bit sector_t
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Cc: <stable@vger.kernel.org> Reported-by: Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sawan Chandak [Fri, 31 Mar 2017 21:37:03 +0000 (14:37 -0700)]
scsi: qla2xxx: Add fix to read correct register value for ISP82xx.
Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.
Fixes: a465537ad1a4 ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect") Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Cc: <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Thu, 23 Mar 2017 13:58:47 +0000 (06:58 -0700)]
scsi: qedf: Fix crash due to unsolicited FIP VLAN response.
We need to initialize qedf->fipvlan_compl in __qedf_probe so that if we
receive an unsolicited FIP VLAN response, the system doesn't crash due
to trying to complete an uninitialized completion.
Also add a check to see if there are any waiters on the completion so we
don't inadvertantly kick start the discovery process due to the
unsolicited frame.
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Cc: <stable@vger.kernel.org> Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fam Zheng [Tue, 28 Mar 2017 04:41:26 +0000 (12:41 +0800)]
scsi: sd: Consider max_xfer_blocks if opt_xfer_blocks is unusable
If device reports a small max_xfer_blocks and a zero opt_xfer_blocks, we
end up using BLK_DEF_MAX_SECTORS, which is wrong and r/w of that size
may get error.
[mkp: tweaked to avoid setting rw_max twice and added typecast]
Cc: <stable@vger.kernel.org> # v4.4+ Fixes: ca369d51b3e ("block/sd: Fix device-imposed transfer length limits") Signed-off-by: Fam Zheng <famz@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Jaehoon Chung [Tue, 21 Mar 2017 12:19:57 +0000 (21:19 +0900)]
scsi: ufs: remove the duplicated checking for supporting clkscaling
There are same conditions for checking whether supporting clkscaling or
not. When ufshcd is supporting clkscaling, active_reqs should be
decreased by one.
[mkp: addressed comment from Bartlomiej]
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Thu, 23 Mar 2017 14:53:45 +0000 (15:53 +0100)]
scsi: lpfc: fix building without debugfs support
On a randconfig build without CONFIG_SCSI_LPFC_DEBUG_FS, I ran into
multiple compile failures:
drivers/scsi/lpfc/lpfc_debugfs.h: In function 'lpfc_debug_dump_wq':
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: error: 'DUMP_FCP' undeclared (first use in this function); did you mean 'DUMP_VAR'?
drivers/scsi/lpfc/lpfc_debugfs.h:405:15: note: each undeclared identifier is reported only once for each function it appears in
drivers/scsi/lpfc/lpfc_debugfs.h:408:22: error: 'DUMP_NVME' undeclared (first use in this function); did you mean 'DUMP_NONE'?
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_ls_rsp_cmp':
drivers/scsi/lpfc/lpfc_nvmet.c:109:2: error: implicit declaration of function 'lpfc_nvmeio_data'; did you mean 'lpfc_mem_free'? [-Werror=implicit-function-declaration]
drivers/scsi/lpfc/lpfc_nvmet.c: In function 'lpfc_nvmet_xmt_fcp_op':
drivers/scsi/lpfc/lpfc_nvmet.c:523:10: error: unused variable 'id' [-Werror=unused-variable]
They are all trivial to fix, so I'm doing it in a combined patch here.
Dick Kennedy [Thu, 23 Mar 2017 12:47:18 +0000 (08:47 -0400)]
scsi: lpfc: Fix PT2PT PRLI reject
lpfc cannot establish connection with targets that send PRLI in P2P
configurations.
If lpfc rejects a PRLI that is sent from a target the target will not
resend and will reject the PRLI send from the initiator.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Henzl [Mon, 20 Mar 2017 15:42:48 +0000 (16:42 +0100)]
scsi: hpsa: fix volume offline state
In a previous patch a hpsa_scsi_dev_t.volume_offline update line has
been removed, so let us put it back..
Fixes: 85b29008d8 (hpsa: update check for logical volume status) Signed-off-by: Tomas Henzl <thenzl@redhat.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 16 Mar 2017 15:07:28 +0000 (23:07 +0800)]
scsi: libsas: fix ata xfer length
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Cc: <stable@vger.kernel.org> Fixes: ff2aeb1eb64c8a4770a6 ("libata: convert to chained sg") Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Sat, 18 Mar 2017 00:02:03 +0000 (17:02 -0700)]
scsi: scsi_dh_alua: Warn if the first argument of alua_rtpg_queue() is NULL
Callers must provide a valid port group to alua_rtpg_queue(). Issue a
kernel warning if that is not the case.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Tang Junhui <tang.junhui@zte.com.cn> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Sat, 18 Mar 2017 00:02:02 +0000 (17:02 -0700)]
scsi: scsi_dh_alua: Ensure that alua_activate() calls the completion function
Callers of scsi_dh_activate(), e.g. dm-mpath, assume that this function
either returns an error code or calls the completion function. Make
alua_activate() call the completion function even if scsi_device_get()
fails.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Tang Junhui <tang.junhui@zte.com.cn> Cc: <stable@vger.kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: commit 03197b61c5ec ("scsi_dh_alua: Use workqueue for RTPG") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Tang Junhui <tang.junhui@zte.com.cn> Cc: <stable@vger.kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
peter chang [Wed, 15 Feb 2017 22:11:54 +0000 (14:11 -0800)]
scsi: sg: check length passed to SG_NEXT_CMD_LEN
The user can control the size of the next command passed along, but the
value passed to the ioctl isn't checked against the usable max command
size.
Cc: <stable@vger.kernel.org> Signed-off-by: Peter Chang <dpf@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Winkler [Tue, 14 Mar 2017 12:19:36 +0000 (14:19 +0200)]
scsi: ufshcd-platform: remove the useless cast in ERR_PTR/IS_ERR
IS_ERR and ERR_PTR already forcefully cast their argument, hence there
is no need for additional (complex) casting.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, command threads fails to return ioctls commands for older
controller versions, since it returns when all the fibs have been
allocated. Another issue is even all the fibs have not been allocated,
the correct allocated fibs is not updated nor freed.
Fixes: 113156bcea9ef1e6 (scsi: aacraid: Reworked aac_command_thread) Reported-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Wed, 8 Mar 2017 22:36:01 +0000 (14:36 -0800)]
scsi: lpfc: Finalize Kconfig options for nvme
Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.
Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
on whether the kernel has the corresponding subsystem support.
Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
possible due to dependency on fc transport). As FCP & NVME divvys up
exchange resources, and given NVME will not be often initially, the
default is changed to FCP only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Winkler [Sun, 12 Mar 2017 10:22:02 +0000 (12:22 +0200)]
scsi: ufs: don't check unsigned type for a negative value
Fix compilation warning:
drivers/scsi/ufs/ufshcd.c:7645:13: warning: comparison of unsigned
expression < 0 is always false [-Wtype-limits]
if ((value < UFS_PM_LVL_0) || (value >= UFS_PM_LVL_MAX))
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 10 Mar 2017 20:35:23 +0000 (14:35 -0600)]
scsi: hpsa: do not timeout reset operations
Resets can take longer than DEFAULT_TIMEOUT.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 10 Mar 2017 20:35:17 +0000 (14:35 -0600)]
scsi: hpsa: limit outstanding rescans
Avoid rescan storms. No need to queue another if one is pending.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 10 Mar 2017 20:35:11 +0000 (14:35 -0600)]
scsi: hpsa: update check for logical volume status
- Add in a new case for volume offline. Resolves internal testing bug
for multilun array management.
- Return correct status for failed TURs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 10 Mar 2017 11:22:15 +0000 (03:22 -0800)]
scsi: megaraid_sas: Driver version upgrade
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 10 Mar 2017 11:22:14 +0000 (03:22 -0800)]
scsi: megaraid_sas: raid6 also require cpuSel check same as raid5
Without this fix, raid6 performance will not be optimal.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 10 Mar 2017 11:22:13 +0000 (03:22 -0800)]
scsi: megaraid_sas: add correct return type check for ldio hint logic for raid1
Return value check of atomic_dec_if_positive is required as it returns
old value minus one. Without this fix, driver will send small ios to
firmware path and that will be a performance issue.
Not critical, but good to have r1_ldio_hint as default value in sdev
private.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Fri, 10 Mar 2017 11:22:12 +0000 (03:22 -0800)]
scsi: megaraid_sas: enable intx only if msix request fails
Without this fix, driver will enable INTx Interrupt pin even though
MSI-x vectors are enabled. See below lspci output. DisINTx is unset for
MSIx setup.
lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
After applying this fix, driver will enable INTx Interrupt pin only if
Legacy interrupt method is required. See below lspci output. DisINTx is
set for MSIx setup. lspci -s 85:00.0 -vvv |grep INT |grep Control
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Anton Blanchard [Sun, 12 Feb 2017 21:49:20 +0000 (08:49 +1100)]
scsi: lpfc: Add shutdown method for kexec
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Cc: <stable@vger.kernel.org> Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: storvsc: Workaround for virtual DVD SCSI version
Hyper-V host emulation of SCSI for virtual DVD device reports SCSI
version 0 (UNKNOWN) but is still capable of supporting REPORTLUN.
Without this patch, a GEN2 Linux guest on Hyper-V will not boot 4.11
successfully with virtual DVD ROM device. What happens is that the SCSI
scan process falls back to doing sequential probing by INQUIRY. But the
storvsc driver has a previous workaround that masks/blocks all errors
reports from INQUIRY (or MODE_SENSE) commands. This workaround causes
the scan to then populate a full set of bogus LUN's on the target and
then sends kernel spinning off into a death spiral doing block reads on
the non-existent LUNs.
By setting the correct blacklist flags, the target with the DVD device
is scanned with REPORTLUN and that works correctly.
Patch needs to go in current 4.11, it is safe but not necessary in older
kernels.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:40 +0000 (09:30 -0800)]
scsi: lpfc: revise version number to 11.2.0.10
Revise lpfc version number to 11.2.0.10
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:39 +0000 (09:30 -0800)]
scsi: lpfc: code cleanups in NVME initiator discovery
This patch addresses the smatch issues identified by Dan Carpenter
in http://www.spinics.net/lists/linux-scsi/msg105665.html
The issues are:
drivers/scsi/lpfc/lpfc_ct.c:943 lpfc_cmpl_ct_cmd_gft_id()
error: we previously assumed 'ndlp' could be null (see line 928)
Action: moved under if check
drivers/scsi/lpfc/lpfc_nvmet.c:1694 lpfc_nvmet_unsol_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1690)
Action: conditionalized arg in printf stmt
drivers/scsi/lpfc/lpfc_nvmet.c:1792 lpfc_nvmet_sol_fcp_issue_abort()
error: we previously assumed 'ndlp' could be null (see line 1788)
Action: conditionalized arg in printf stmt
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:37 +0000 (09:30 -0800)]
scsi: lpfc: correct rdp diag portnames
NVME merge reverted diag port names to the physical port.
They should be the vport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:36 +0000 (09:30 -0800)]
scsi: lpfc: remove dead sli3 nvme code
Remove nvme teardown calls that should not be there on sli3 devices
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:35 +0000 (09:30 -0800)]
scsi: lpfc: correct double print
Correct a merge error that had debug data printed twice for the
same element
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:34 +0000 (09:30 -0800)]
scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
Without apriori understanding of what the define is, the name gives
a very different impression of what it is (a max delay value
for an EQ). Rename the define so it reflects what it is: the number
of EQ IDs that can be set in one instance of the MODIFY_EQ_DELAY
mbx command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:33 +0000 (09:30 -0800)]
scsi: lpfc: Rework lpfc Kconfig for NVME options
Reworked Kconfig so that lfpc only requires the scsi stack.
NVME Initiator and NVME Target support can be enabled if
the other NVMe subsystems have been enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:32 +0000 (09:30 -0800)]
scsi: lpfc: add transport eh_timed_out reference
Christoph's prior patch missed the template for the sli3 adapters,
which is now the "no host reset" template. Add the transport
eh_timed_out handler to the no host reset template
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:31 +0000 (09:30 -0800)]
scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
A previous change unilaterally removed the hba reset entry point
from the sli3 host template. This was done to allow tape devices
being used for back up from being removed. Why was this done ?
When there was non-responding device on the fabric, the error
escalation policy would escalate to the reset handler. When the
reset handler was called, it would reset the adapter, dropping
link, thus logging out and terminating all i/o's - on any target.
If there was a tape device on the same adapter that wasn't in
error, it would kill the tape i/o's, effectively killing the
tape device state. With the reset point removed, the adapter
reset avoided the fabric logout, allowing the other devices to
continue to operate unaffected. A hack - yes. Hint: we really
need a transport I_T nexus reset callback added to the eh process
(in between the SCSI target reset and hba reset points), so a
fc logout could occur to the one bad target only and stop the error
escalation process.
This patch commonizes the approach so it can be used for sli3 and sli4
adapters, but mandates the admin, via module parameter, specifically
identify which adapters the resets are to be removed for. Additionally,
bus_reset, which sends Target Reset TMFs to all targets, is also removed
from the template as it too has the same effect as the adapter reset.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Laurence Oberman <loberman@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:30 +0000 (09:30 -0800)]
scsi: lpfc: add NVME exchange aborts
previous code did little more than log a message.
This patch adds abort path support, modeled after the SCSI code paths.
Currently addresses only the initiator path. Target path under
development, but stubbed out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:29 +0000 (09:30 -0800)]
scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
nvme bufs get allocated even when the registration fails.
Move allocation into the rsgistration success path.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:28 +0000 (09:30 -0800)]
scsi: lpfc: Fix IO submission if WQ is full
For both initiator and target: if WQ is full, return -EBUSY.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:27 +0000 (09:30 -0800)]
scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
Word 1 in NVME CMD IU appears byte swapped from value placed in WQE
Should be Big Endian value in WQE word 16
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:26 +0000 (09:30 -0800)]
scsi: lpfc: Fix RCTL value on NVME LS request and response
NVME LS requests and responses had wrong R_CTL values.
Use the FC4 ELS Request and Response defines (defines badly
named, they are FC4 LS's) instead of the base ELS values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:25 +0000 (09:30 -0800)]
scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
if REG_VPI fails, the driver was incorrectly issuing INIT_VFI
(a SLI4 command) on a SLI3 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:24 +0000 (09:30 -0800)]
scsi: lpfc: fix missing spin_unlock on sql_list_lock
From: Colin Ian King <colin.king@canonical.com>
In the case where sglq is null, the current code just returns without
unlocking the spinlock sql_list_lock. Fix this by breaking out of the
while loop and the exit path will then unlock and return NULL as was
the original intention.
Detected by CoverityScan, CID#1411635 ("Missing unlock")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:23 +0000 (09:30 -0800)]
scsi: lpfc: don't dereference dma_buf->iocbq before null check
From: Colin Ian King <colin.king@canonical.com>
dma_buf->iocbq is being dereferenced immediately before it is
being null checked, so we have a potential null pointer dereference
bug. Fix this by only dereferencing it only once we have passed
a null check on the pointer.
Detected by CoverityScan, CID#1411652 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:22 +0000 (09:30 -0800)]
scsi: lpfc: sanity check hrq is null before dereferencing it
From: Colin Ian King <colin.king@canonical.com>
The sanity check for hrq should be moved to before the deference
of hrq to ensure we don't perform a null pointer deference.
Detected by CoverityScan, CID#1411650 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
James Smart [Sat, 4 Mar 2017 17:30:21 +0000 (09:30 -0800)]
scsi: lpfc: remove redundant assignment of sgel
From: Colin Ian King <colin.king@canonical.com>
In the NVMET_FCOP_RSP case, sgel is assigned but never used and
hence is redundant and can be removed.
Detected by CoverityScan, CID#1411658 ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tomas Jasek [Fri, 3 Mar 2017 12:45:48 +0000 (13:45 +0100)]
scsi: lpfc: replace init_timer by setup_timer
This patch shortens every init_timer in lpfc module followed by function
and data assignment using setup_timer. This is purely cleanup patch, it
does not add new functionality nor remove any existing functionality.
Joe Perches [Mon, 6 Mar 2017 18:32:27 +0000 (10:32 -0800)]
scsi: qedf: Use vsprintf extension %pad
Using %llx for a dma_addr_t can lead to format/argument mismatches. Use
%pad and the address of the dma_addr_t instead.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Perches [Sat, 4 Mar 2017 08:07:04 +0000 (00:07 -0800)]
scsi: qedf: Fix defective logging format and argument mismatches
Add __printf compiler verification of format and arguments. Fix
fallout.
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Perches [Fri, 3 Mar 2017 01:14:47 +0000 (17:14 -0800)]
scsi: qla2xxx: Fix ql_dump_buffer
Recent printk changes for KERN_CONT cause this logging to be defectively
emitted on multiple lines. Fix it.
Also reduces object size a trivial amount.
$ size drivers/scsi/qla2xxx/qla_dbg.o*
text data bss dec hex filename
39125 0 0 39125 98d5 drivers/scsi/qla2xxx/qla_dbg.o.new
39164 0 0 39164 98fc drivers/scsi/qla2xxx/qla_dbg.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arnd Bergmann [Thu, 2 Mar 2017 14:58:03 +0000 (15:58 +0100)]
scsi: qedi: fix build error without DEBUG_FS
Without CONFIG_DEBUG_FS, we run into a link error:
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_poll':
qedi_iscsi.c:(.text.qedi_ep_poll+0x134): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_disconnect':
qedi_iscsi.c:(.text.qedi_ep_disconnect+0x36c): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_iscsi.o: In function `qedi_ep_connect':
qedi_iscsi.c:(.text.qedi_ep_connect+0x350): undefined reference to `do_not_recover'
drivers/scsi/qedi/qedi_fw.o: In function `qedi_tmf_work':
qedi_fw.c:(.text.qedi_tmf_work+0x3b4): undefined reference to `do_not_recover'
This defines the symbol as a constant in this case, as there is no way to
set it to anything other than zero without DEBUG_FS. In addition, I'm renaming
it to qedi_do_not_recover in order to put it into a driver specific namespace,
as "do_not_recover" is a really bad name for a kernel-wide global identifier
when it is used only in one driver.
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Linus Torvalds [Sat, 4 Mar 2017 19:36:19 +0000 (11:36 -0800)]
Merge tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Radim Krčmář:
"Second batch of KVM changes for the 4.11 merge window:
PPC:
- correct assumption about ASDR on POWER9
- fix MMIO emulation on POWER9
x86:
- add a simple test for ioperm
- cleanup TSS (going through KVM tree as the whole undertaking was
caused by VMX's use of TSS)
- fix nVMX interrupt delivery
- fix some performance counters in the guest
... and two cleanup patches"
* tag 'kvm-4.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: Fix pending events injection
x86/kvm/vmx: remove unused variable in segment_base()
selftests/x86: Add a basic selftest for ioperm
x86/asm: Tidy up TSS limit code
kvm: convert kvm.users_count from atomic_t to refcount_t
KVM: x86: never specify a sample period for virtualized in_tx_cp counters
KVM: PPC: Book3S HV: Don't use ASDR for real-mode HPT faults on POWER9
KVM: PPC: Book3S HV: Fix software walk of guest process page tables
Linus Torvalds [Sat, 4 Mar 2017 19:26:18 +0000 (11:26 -0800)]
Merge tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for issues that
showed up after the big set if changes you merged last week.
Nothing major, just small bugs resolved in some IIO drivers, a lustre
allocation fix, and some RaspberryPi driver fixes for reported
problems, as well as a MAINTAINERS entry update.
All of these have been in linux-next for a week with no reported
issues"
* tag 'staging-4.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fsl-mc: fix warning in DT ranges parser
MAINTAINERS: Remove Noralf Trønnes as fbtft maintainer
staging: vchiq_2835_arm: Make cache-line-size a required DT property
staging: bcm2835/mmal-vchiq: unlock on error in buffer_from_host()
staging/lustre/lnet: Fix allocation size for sv_cpt_data
iio: adc: xilinx: Fix error handling
iio: 104-quad-8: Fix off-by-one error when addressing flag register
iio: adc: handle unknow of_device_id data
Linus Torvalds [Sat, 4 Mar 2017 18:42:53 +0000 (10:42 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- vmalloc stack regression in CCM
- Build problem in CRC32 on ARM
- Memory leak in cavium
- Missing Kconfig dependencies in atmel and mediatek
- XTS Regression on some platforms (s390 and ppc)
- Memory overrun in CCM test vector
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: vmx - Use skcipher for xts fallback
crypto: vmx - Use skcipher for cbc fallback
crypto: testmgr - Pad aes_ccm_enc_tv_template vector
crypto: arm/crc32 - add build time test for CRC instruction support
crypto: arm/crc32 - fix build error with outdated binutils
crypto: ccm - move cbcmac input off the stack
crypto: xts - Propagate NEED_FALLBACK bit
crypto: api - Add crypto_requires_off helper
crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
crypto: cavium - fix leak on curr if curr->head fails to be allocated
crypto: cavium - Fix couple of static checker errors
Linus Torvalds [Sat, 4 Mar 2017 05:36:56 +0000 (21:36 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
WANG Cong [Fri, 3 Mar 2017 20:21:14 +0000 (12:21 -0800)]
strparser: destroy workqueue on module exit
Fixes: 43a0c6751a32 ("strparser: Stream parser for messages") Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Missing check for full sock in ip_route_me_harder(), from
Florian Westphal.
2) Incorrect sip helper structure initilization that breaks it when
several ports are used, from Christophe Leroy.
3) Fix incorrect assumption when looking up for matching with adjacent
intervals in the nft_set_rbtree.
4) Fix broken netlink event error reporting in nf_tables that results
in misleading ESRCH errors propagated to userspace listeners.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 4 Mar 2017 00:48:48 +0000 (16:48 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix and regression test case for nvdimm namespace label
compatibility.
Details:
- An "nvdimm namespace label" is metadata on an nvdimm that
provisions dimm capacity into a "namespace" that can host a block
device / dax-filesytem, or a device-dax character device.
A namespace is an object that other operating environment and
platform firmware needs to comprehend for capabilities like booting
from an nvdimm.
The label metadata contains a checksum that Linux was not
calculating correctly leading to other environments rejecting the
Linux label.
These have received a build success notification from the kbuild
robot, and a positive test result from Nick who reported the problem"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, libnvdimm: fix interleave set cookie calculation
tools/testing/nvdimm: make iset cookie predictable
Linus Torvalds [Sat, 4 Mar 2017 00:44:21 +0000 (16:44 -0800)]
Merge tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix NULL pointer dereferences in many DesignWare-based drivers due to
refactoring error
- fix Altera config write breakage due to my refactoring error
* tag 'pci-v4.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: altera: Fix TLP_CFG_DW0 for TLP write
PCI: dwc: Fix crashes seen due to missing assignments
Linus Torvalds [Sat, 4 Mar 2017 00:20:06 +0000 (16:20 -0800)]
Merge branch 'parisc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes and cleanups from Helge Deller:
"Nothing really important in this patchset: fix resource leaks in error
paths, coding style cleanups and code removal"
* 'parisc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Remove flush_user_dcache_range and flush_user_icache_range
parisc: fix a printk
parisc: ccio-dma: Handle return NULL error from ioremap_nocache
parisc: Define access_ok() as macro
parisc: eisa: Fix resource leaks in error paths
parisc: eisa: Remove coding style errors
Linus Torvalds [Sat, 4 Mar 2017 00:17:55 +0000 (16:17 -0800)]
Merge tag 'xtensa-20170303' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa updates from Max Filippov:
- clean up bootable image build targets: provide separate 'Image',
'zImage' and 'uImage' make targets that only build corresponding
image type. Make 'all' build all images appropriate for a platform
- allow merging vectors code into .text section as a preparation step
for XIP support
- fix handling external FDT when the kernel is built without
BLK_DEV_INITRD support
* tag 'xtensa-20170303' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: allow merging vectors into .text section
xtensa: clean up bootable image build targets
xtensa: move parse_tag_fdt out of #ifdef CONFIG_BLK_DEV_INITRD
Linus Torvalds [Sat, 4 Mar 2017 00:15:48 +0000 (16:15 -0800)]
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
Linus Torvalds [Sat, 4 Mar 2017 00:00:59 +0000 (16:00 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull SMB3 fixes from Steve French:
"Some small bug fixes as well as SMB2.1/SMB3 enablement for DFS (global
namespace) which previously was only enabled for CIFS"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
smb2: Enforce sec= mount option
CIFS: Fix sparse warnings
CIFS: implement get_dfs_refer for SMB2+
CIFS: use DFS pathnames in SMB2+ Create requests
CIFS: set signing flag in SMB2+ TreeConnect if needed
CIFS: let ses->ipc_tid hold smb2 TreeIds
CIFS: add use_ipc flag to SMB2_ioctl()
CIFS: add build_path_from_dentry_optional_prefix()
CIFS: move DFS response parsing out of SMB1 code
CIFS: Fix possible use after free in demultiplex thread
Martyn Welch [Fri, 3 Mar 2017 22:43:30 +0000 (22:43 +0000)]
docs: Fix htmldocs build failure
Build of HTML docs failing due to conversion of deviceiobook.tmpl in 8a8a602f and regulator.tmpl in 028f2533 to RST without removing from
DOCBOOKS in Makefile, resulting (in the case of deviceiobook) the
following error:
make[1]: *** No rule to make target 'Documentation/DocBook/deviceiobook.xml', needed by 'Documentation/DocBook/deviceiobook.aux.xml'. Stop.
Makefile:1452: recipe for target 'htmldocs' failed
make: *** [htmldocs] Error 2
Update DOCBOOKS to reflect available books.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Linus Torvalds [Fri, 3 Mar 2017 19:55:57 +0000 (11:55 -0800)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"Because copy up can take a long time, serialized copy ups could be a
big performance bottleneck. This update allows concurrent copy up of
regular files eliminating this potential problem.
There are also minor fixes"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: drop CAP_SYS_RESOURCE from saved mounter's credentials
ovl: properly implement sync_filesystem()
ovl: concurrent copy up of regular files
ovl: introduce copy up waitqueue
ovl: copy up regular file using O_TMPFILE
ovl: rearrange code in ovl_copy_up_locked()
ovl: check if upperdir fs supports O_TMPFILE
Linus Torvalds [Fri, 3 Mar 2017 19:38:56 +0000 (11:38 -0800)]
Merge branch 'rebased-statx' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs 'statx()' update from Al Viro.
This adds the new extended stat() interface that internally subsumes our
previous stat interfaces, and allows user mode to specify in more detail
what kind of information it wants.
It also allows for some explicit synchronization information to be
passed to the filesystem, which can be relevant for network filesystems:
is the cached value ok, or do you need open/close consistency, or what?
From David Howells.
Andreas Dilger points out that the first version of the extended statx
interface was posted June 29, 2010:
Linus Torvalds [Fri, 3 Mar 2017 18:53:35 +0000 (10:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A collection of fixes for this merge window, either fixes for existing
issues, or parts that were waiting for acks to come in. This pull
request contains:
- Allocation of nvme queues on the right node from Shaohua.
This was ready long before the merge window, but waiting on an ack
from Bjorn on the PCI bit. Now that we have that, the three patches
can go in.
- Two fixes for blk-mq-sched with nvmeof, which uses hctx specific
request allocations. This caused an oops. One part from Sagi, one
part from Omar.
- A loop partition scan deadlock fix from Omar, fixing a regression
in this merge window.
- A three-patch series from Keith, closing up a hole on clearing out
requests on shutdown/resume.
- A stable fix for nbd from Josef, fixing a leak of sockets.
- Two fixes for a regression in this window from Jan, fixing a
problem with one of his earlier patches dealing with queue vs bdi
life times.
- A fix for a regression with virtio-blk, causing an IO stall if
scheduling is used. From me.
- A fix for an io context lock ordering problem. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Move bdi_unregister() to del_gendisk()
blk-mq: ensure that bd->last is always set correctly
block: don't call ioc_exit_icq() with the queue lock held for blk-mq
block: Initialize bd_bdi on inode initialization
loop: fix LO_FLAGS_PARTSCAN hang
nvme: Complete all stuck requests
blk-mq: Provide freeze queue timeout
blk-mq: Export blk_mq_freeze_queue_wait
nbd: stop leaking sockets
blk-mq: move update of tags->rqs to __blk_mq_alloc_request()
blk-mq: kill blk_mq_set_alloc_data()
blk-mq: make blk_mq_alloc_request_hctx() allocate a scheduler request
blk-mq-sched: Allocate sched reserved tags as specified in the original queue tagset
nvme: allocate nvme_queue in correct node
PCI: add an API to get node from vector
blk-mq: allocate blk_mq_tags and requests in correct node
Linus Torvalds [Fri, 3 Mar 2017 18:16:38 +0000 (10:16 -0800)]
Merge branch 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
Linus Torvalds [Fri, 3 Mar 2017 18:13:12 +0000 (10:13 -0800)]
Merge tag 'linux-kselftest-4.11-rc1-urgent_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"This update consists of an urgent fix for individual test build
failures introduced in the 4.11-rc1 update"
* tag 'linux-kselftest-4.11-rc1-urgent_fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: lib.mk Fix individual test builds
David S. Miller [Fri, 3 Mar 2017 18:06:39 +0000 (10:06 -0800)]
Merge branch 'sfx-fixes'
Edward Cree says:
====================
sfc: couple of fixes
First patch addresses a construct that causes sparse to error out.
With that fixed, sparse makes some warnings on ef10.c, second patch
fixes one of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 3 Mar 2017 15:22:27 +0000 (15:22 +0000)]
sfc: fix IPID endianness in TSOv2
The value we read from the header is in network byte order, whereas
EFX_POPULATE_QWORD_* takes values in host byte order (which it then
converts to little-endian, as MCDI is little-endian).
Fixes: e9117e5099ea ("sfc: Firmware-Assisted TSO version 2") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 3 Mar 2017 15:22:09 +0000 (15:22 +0000)]
sfc: avoid max() in array size
It confuses sparse, which thinks the size isn't constant. Let's achieve
the same thing with a BUILD_BUG_ON, since we know which one should be
bigger and don't expect them ever to change.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Fri, 3 Mar 2017 05:44:26 +0000 (00:44 -0500)]
rds: remove unnecessary returned value check
The function rds_trans_register always returns 0. As such, it is not
necessary to check the returned value.
Cc: Joe Jin <joe.jin@oracle.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 2 Mar 2017 23:48:52 +0000 (23:48 +0000)]
rxrpc: Fix potential NULL-pointer exception
Fix a potential NULL-pointer exception in rxrpc_do_sendmsg(). The call
state check that I added should have gone into the else-body of the
if-statement where we actually have a call to check.
Found by CoverityScan CID#1414316 ("Dereference after null check").
Fixes: 540b1c48c37a ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg") Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Mar 2017 17:46:54 +0000 (09:46 -0800)]
Merge branch 'nfp-fixes'
Jakub Kicinski says:
====================
nfp: RX and XDP buffer fixes
Two trivial fixes for code introduced with XDP support. First
one corrects the buffer size we populate a register with. The
register is designed to be used for scatter transfers which
the driver (and most FWs) don't support so it's not critical.
The other one for DMA direction is mostly cosmetic, DMA API
doesn't seem to care today about the precise direction in sync
calls.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 2 Mar 2017 23:26:21 +0000 (15:26 -0800)]
nfp: correct DMA direction in XDP DMA sync
dma_sync_single_for_*() takes the direction in which the buffer
was mapped, not the direction of the sync. We should sync XDP
buffers bidirectionally.
Fixes: ecd63a0217d5 ("nfp: add XDP support in the driver") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 2 Mar 2017 23:26:20 +0000 (15:26 -0800)]
nfp: don't tell FW about the reserved buffer space
Since commit c0f031bc8866 ("nfp_net: use alloc_frag() and build_skb()")
we are allocating buffers which have to hold both the data and skb to
be created in place by build_skb().
FW should only be told about the buffer space it can DMA to, that
is without the build_skb() headroom and tailroom. Note: firmware
applications should validate the buffers against both MTU and
free list buffer size so oversized packets would not pass through
the NIC anyway.
Fixes: c0f031bc8866 ("nfp: use alloc_frag() and build_skb()") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Changes in v5:
* Rebased to the latest code and fixed up a compile error due to the
mac_addr struct going away (found by David Miller)
Changes in v4:
* Added the udelays from the previous code (per David Miller)
Changes in v3:
* Reworked the init sequence patch to only remove the device reset if
the device is actually in reset. Given that this code doesn't bear
much resemblance to the original code, I'm changing the author of the
patch. This was tested on NS2 SVK.
Changes in v2:
* Reworked the first match to make it more obvious what portions of the
register were being preserved (Per Rafal Mileki)
* Style change to reorder the function variables in patch 2 (per Sergei
Shtylyov)
Bug fixes for bgmac driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-artful-kernel.git / log