Herbert Xu [Thu, 25 Dec 2008 00:05:13 +0000 (11:05 +1100)]
crypto: aes - Precompute tables
The tables used by the various AES algorithms are currently
computed at run-time. This has created an init ordering problem
because some AES algorithms may be registered before the tables
have been initialised.
This patch gets around this whole thing by precomputing the tables.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Lee Nipper [Sat, 20 Dec 2008 06:09:25 +0000 (17:09 +1100)]
crypto: talitos - Ack done interrupt in isr instead of tasklet
Previous commit for interrupt mitigation moved the done interrupt
acknowlegement from the isr to the talitos_done tasklet.
This patch moves the done interrupt acknowledgement back
into the isr so that done interrupts will always be acknowledged.
This covers the case for acknowledging interrupts for channel done processing
that has actually already been completed by the tasklet prior to fielding
a pending interrupt.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: testmgr - Correct comment about deflate parameters
The comment for the deflate test vectors says the winbits parameter is 11,
while the deflate module actually uses -11 (a negative window bits parameter
enables the raw deflate format instead of the zlib format).
Correct this, to avoid confusion about the format used.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jarod Wilson [Wed, 17 Dec 2008 05:51:13 +0000 (16:51 +1100)]
crypto: des3_ede - permit weak keys unless REQ_WEAK_KEY set
While its a slightly insane to bypass the key1 == key2 ||
key2 == key3 check in triple-des, since it reduces it to the
same strength as des, some folks do need to do this from time
to time for backwards compatibility with des.
My own case is FIPS CAVS test vectors. Many triple-des test
vectors use a single key, replicated 3x. In order to get the
expected results, des3_ede_setkey() needs to only reject weak
keys if the CRYPTO_TFM_REQ_WEAK_KEY flag is set.
Also sets a more appropriate RES flag when a weak key is found.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: testmgr - Validate output length in (de)compression tests
When self-testing (de)compression algorithms, make sure the actual size of
the (de)compressed output data matches the expected output size.
Otherwise, in case the actual output size would be smaller than the expected
output size, the subsequent buffer compare test would still succeed, and no
error would be reported.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ingo Molnar [Tue, 25 Nov 2008 15:19:24 +0000 (23:19 +0800)]
crypto: testmgr - Fix error flow of test_comp
This warning:
crypto/testmgr.c: In function ‘test_comp’:
crypto/testmgr.c:829: warning: ‘ret’ may be used uninitialized in this function
triggers because GCC correctly notices that in the ctcount == 0 &&
dtcount != 0 input condition case this function can return an undefined
value, if the second loop fails.
Remove the shadowed 'ret' variable from the second loop that was probably
unintended.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Evgeniy Polyakov [Mon, 24 Nov 2008 14:04:39 +0000 (22:04 +0800)]
crypto: hifn_795x - Fix queue management
Fix queue management. Change ring size and perform its check not
one after another descriptor, but using stored pointers to the last
checked descriptors.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HIFN uses the transform context to store per-request data, which breaks
when more than one request is outstanding. Move per request members from
struct hifn_context to a new struct hifn_request_context and convert
the code to use this.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The ANSI X9.31 PRNG docs aren't particularly clear on how to increment DT,
but empirical testing shows we're incrementing from the wrong end. A 10,000
iteration Monte Carlo RNG test currently winds up not getting the expected
result.
From http://csrc.nist.gov/groups/STM/cavp/documents/rng/RNGVS.pdf :
If I load up ansi_cprng w/dbg=1 though, it was fairly obvious what was
going wrong:
----8<----
getting 16 random bytes for context ffff810033fb2b10
Calling _get_more_prng_bytes for context ffff810033fb2b10
Input DT: 00000000: e6 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
Input I: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Input V: 00000000: f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
tmp stage 0: 00000000: e6 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
tmp stage 1: 00000000: f4 8e cb 25 94 3e 8c 31 d6 14 cd 8a 23 f1 3f 84
tmp stage 2: 00000000: 8c 53 6f 73 a4 1a af d4 20 89 68 f4 58 64 f8 be
Returning new block for context ffff810033fb2b10
Output DT: 00000000: e7 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
Output I: 00000000: 04 8e cb 25 94 3e 8c 31 d6 14 cd 8a 23 f1 3f 84
Output V: 00000000: 48 89 3b 71 bc e4 00 b6 5e 21 ba 37 8a 0a d5 70
New Random Data: 00000000: 88 dd a4 56 30 24 23 e5 f6 9d a5 7e 7b 95 c7 3a
Calling _get_more_prng_bytes for context ffff810033fb2b10
Input DT: 00000000: e7 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
Input I: 00000000: 04 8e cb 25 94 3e 8c 31 d6 14 cd 8a 23 f1 3f 84
Input V: 00000000: 48 89 3b 71 bc e4 00 b6 5e 21 ba 37 8a 0a d5 70
tmp stage 0: 00000000: e7 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
tmp stage 1: 00000000: 80 6b 3a 8c 23 ae 8f 53 be 71 4c 16 fc 13 b2 ea
tmp stage 2: 00000000: 2a 4d e1 2a 0b 58 8e e6 36 b8 9c 0a 26 22 b8 30
Returning new block for context ffff810033fb2b10
Output DT: 00000000: e8 b3 be 78 2a 23 fa 62 d7 1d 4a fb b0 e9 22 fc
Output I: 00000000: c8 e2 01 fd 9f 4a 8f e5 e0 50 f6 21 76 19 67 9a
Output V: 00000000: ba 98 e3 75 c0 1b 81 8d 03 d6 f8 e2 0c c6 54 4b
New Random Data: 00000000: e2 af e0 d7 94 12 01 03 d6 e8 6a 2b 50 3b df aa
returning 16 from get_prng_bytes in context ffff810033fb2b10
----8<----
The expected result is there, in the first "New Random Data", but we're
incorrectly making a second call to _get_more_prng_bytes, due to some checks
that are slightly off, which resulted in our original bytes never being
returned anywhere.
One approach to fixing this would be to alter some byte_count checks in
get_prng_bytes, but it would mean the last DEFAULT_BLK_SZ bytes would be
copied a byte at a time, rather than in a single memcpy, so a slightly more
involved, equally functional, and ultimately more efficient way of fixing this
was suggested to me by Neil, which I'm submitting here. All of the RNGVS ANSI
X9.31 AES128 VST test vectors I've passed through ansi_cprng are now returning
the expected results with this change.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Fri, 7 Nov 2008 07:11:47 +0000 (15:11 +0800)]
libcrc32c: Move implementation to crypto crc32c
This patch swaps the role of libcrc32c and crc32c. Previously
the implementation was in libcrc32c and crc32c was a wrapper.
Now the code is in crc32c and libcrc32c just calls the crypto
layer.
The reason for the change is to tap into the algorithm selection
capability of the crypto API so that optimised implementations
such as the one utilising Intel's CRC32C instruction can be
used where available.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Fri, 7 Nov 2008 06:58:52 +0000 (14:58 +0800)]
crypto: crc32c - Test descriptor context format
This patch adds a test for the requirement that all crc32c algorithms
shall store the partial result in the first four bytes of the descriptor
context.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 31 Aug 2008 12:21:09 +0000 (22:21 +1000)]
crypto: hash - Export shash through hash
This patch allows shash algorithms to be used through the old hash
interface. This is a transitional measure so we can convert the
underlying algorithms to shash before converting the users across.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Thu, 6 Nov 2008 06:39:16 +0000 (14:39 +0800)]
crypto: api - Call type show function before legacy for proc
This patch makes /proc/crypto call the type-specific show function
if one is present before calling the legacy show functions for
cipher/digest/compress. This allows us to reuse the type values
for those legacy types. In particular, hash and digest will share
one type value while shash is phased in as the default hash type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 2 Nov 2008 13:38:11 +0000 (21:38 +0800)]
crypto: hash - Add import/export interface
It is often useful to save the partial state of a hash function
so that it can be used as a base for two or more computations.
The most prominent example is HMAC where all hashes start from
a base determined by the key. Having an import/export interface
means that we only have to compute that base once rather than
for each message.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 31 Aug 2008 05:47:27 +0000 (15:47 +1000)]
crypto: hash - Add shash interface
The shash interface replaces the current synchronous hash interface.
It improves over hash in two ways. Firstly shash is reentrant,
meaning that the same tfm may be used by two threads simultaneously
as all hashing state is stored in a local descriptor.
The other enhancement is that shash no longer takes scatter list
entries. This is because shash is specifically designed for
synchronous algorithms and as such scatter lists are unnecessary.
All existing hash users will be converted to shash once the
algorithms have been completely converted.
There is also a new finup function that combines update with final.
This will be extended to ahash once the algorithm conversion is
done.
This is also the first time that an algorithm type has their own
registration function. Existing algorithm types will be converted
to this way in due course.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sat, 20 Sep 2008 21:52:53 +0000 (06:52 +0900)]
crypto: api - Rebirth of crypto_alloc_tfm
This patch reintroduces a completely revamped crypto_alloc_tfm.
The biggest change is that we now take two crypto_type objects
when allocating a tfm, a frontend and a backend. In fact this
simply formalises what we've been doing behind the API's back.
For example, as it stands crypto_alloc_ahash may use an
actual ahash algorithm or a crypto_hash algorithm. Putting
this in the API allows us to do this much more cleanly.
The existing types will be converted across gradually.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 14 Sep 2008 01:19:03 +0000 (18:19 -0700)]
crypto: api - Move type exit function into crypto_tfm
The type exit function needs to undo any allocations done by the type
init function. However, the type init function may differ depending
on the upper-level type of the transform (e.g., a crypto_blkcipher
instantiated as a crypto_ablkcipher).
So we need to move the exit function out of the lower-level
structure and into crypto_tfm itself.
As it stands this is a no-op since nobody uses exit functions at
all. However, all cases where a lower-level type is instantiated
as a different upper-level type (such as blkcipher as ablkcipher)
will be converted such that they allocate the underlying transform
and use that instead of casting (e.g., crypto_ablkcipher casted
into crypto_blkcipher). That will need to use a different exit
function depending on the upper-level type.
This patch also allows the type init/exit functions to call (or not)
cra_init/cra_exit instead of always calling them from the top level.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Neil Horman [Wed, 5 Nov 2008 04:13:14 +0000 (12:13 +0800)]
crypto: ansi_cprng - Allow resetting of DT value
This is a patch that was sent to me by Jarod Wilson, marking off my
outstanding todo to allow the ansi cprng to set/reset the DT counter value in a
cprng instance. Currently crytpo_rng_reset accepts a seed byte array which is
interpreted by the ansi_cprng as a {V key} tuple. This patch extends that tuple
to now be {V key DT}, with DT an optional value during reset. This patch also
fixes a bug we noticed in which the offset of the key area of the seed is
started at DEFAULT_PRNG_KSZ rather than DEFAULT_BLK_SZ as it should be.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Sun, 31 Aug 2008 05:58:45 +0000 (15:58 +1000)]
crypto: padlock - Avoid resetting cword on successive operations
Resetting the control word is quite expensive. Fortunately this
isn't an issue for the common operations such as CBC and ECB as
the whole operation is done through a single call. However, modes
such as LRW and XTS have to call padlock over and over again for
one operation which really hurts if each call resets the control
word.
This patch uses an idea by Sebastian Siewior to store the last
control word used on a CPU and only reset the control word if
that changes.
Note that any task switch automatically resets the control word
so we only need to be accurate with regard to the stored control
word when no task switches occur.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In commit ec6644d6325b5a38525f1d5b20fd4bf7db05cf2a "crypto: talitos - Preempt
overflow interrupts", the test in atomic_inc_not_zero was interpreted by the
author to be applied after the increment operation (not before). This off-by-one
fix prevents overflow error interrupts from occurring when requests are frequent
and large enough to do so.
Signed-off-by: Vishnu Suresh <Vishnu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Harvey Harrison [Sun, 12 Oct 2008 12:40:12 +0000 (20:40 +0800)]
crypto: camellia - use kernel-provided bitops, unaligned access
Remove the private implementation of 32-bit rotation and unaligned
access with byteswapping.
As a bonus, fixes sparse warnings:
crypto/camellia.c:602:2: warning: cast to restricted __be32
crypto/camellia.c:603:2: warning: cast to restricted __be32
crypto/camellia.c:604:2: warning: cast to restricted __be32
crypto/camellia.c:605:2: warning: cast to restricted __be32
crypto/camellia.c:710:2: warning: cast to restricted __be32
crypto/camellia.c:711:2: warning: cast to restricted __be32
crypto/camellia.c:712:2: warning: cast to restricted __be32
crypto/camellia.c:713:2: warning: cast to restricted __be32
crypto/camellia.c:714:2: warning: cast to restricted __be32
crypto/camellia.c:715:2: warning: cast to restricted __be32
crypto/camellia.c:716:2: warning: cast to restricted __be32
crypto/camellia.c:717:2: warning: cast to restricted __be32
[Thanks to Tomoyuki Okazaki for spotting the typo] Tested-by: Carlo E. Prelz <fluido@fluido.as> Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Neil Horman [Sun, 12 Oct 2008 12:36:51 +0000 (20:36 +0800)]
crypto: testmgr - Trigger a panic when self test fails in FIPS mode
The FIPS specification requires that should self test for any supported
crypto algorithm fail during operation in fips mode, we need to prevent
the use of any crypto functionality until such time as the system can
be re-initialized. Seems like the best way to handle that would be
to panic the system if we were in fips mode and failed a self test.
This patch implements that functionality. I've built and run it
successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kim Phillips [Sun, 12 Oct 2008 12:33:14 +0000 (20:33 +0800)]
crypto: talitos - Perform auth check in h/w if on sec 2.1 and above
SEC version 2.1 and above adds the capability to do the IPSec ICV
memcmp in h/w. Results of the cmp are written back in the descriptor
header, along with the done status. A new callback is added that
checks these ICCR bits instead of performing the memcmp on the core,
and is enabled by h/w capability.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
After testing on different parts, another condition was added
before using h/w auth check because different
SEC revisions require different handling.
The SEC 3.0 allows a more flexible link table where
the auth data can span separate link table entries.
The SEC 2.4/2.1 does not support this case.
So a test was added in the decrypt routine
for a fragmented case; the h/w auth check is disallowed for
revisions not having the extent in the link table;
in this case the hw auth check is done by software.
A portion of a previous change for SEC 3.0 link table handling
was removed since it became dead code with the hw auth check supported.
This seems to be the best compromise for using hw auth check
on supporting SEC revisions; it keeps the link table logic
simpler for the fragmented cases.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In talitos_interrupt, upon one done interrupt, mask further done interrupts,
and ack only any error interrupt.
In talitos_done, unmask done interrupts after completing processing.
In flush_channel, ack each done channel processed.
Keep done overflow interrupts masked because even though each pkt
is ack'ed, a few done overflows still occur.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kim Phillips [Sun, 12 Oct 2008 12:19:35 +0000 (20:19 +0800)]
crypto: talitos - Pass correct interrupt status to error handler
Since we ack early, the re-read interrupt status in talitos_error
may be already updated with a new value. Pass the error ISR value
directly in order to report and handle the error based on the correct
error status.
Also remove unused error tasklet.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Lee Nipper <lee.nipper@freescale.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On Tue, Sep 23, 2008 at 08:06:32PM +0200, Dimitri Puzin (max@psycast.de) wrote:
> With this patch applied it still doesn't work as expected. The overflow
> messages are gone however syslog shows
> [ 120.924266] hifn0: abort: c: 0, s: 1, d: 0, r: 0.
> when doing cryptsetup luksFormat as in original e-mail. At this point
> cryptsetup hangs and can't be killed with -SIGKILL. I've attached
> SysRq-t dump of this condition.
Yes, I was wrong with the patch: HIFN does not support 64-bit addresses
afaics.
Attached patch should not allow HIFN to be registered on 64-bit arch, so
crypto layer will fallback to the software algorithms.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
and are queued up for v2.6.29. This shows that the facility is still not
tested well enough to release into a stable kernel - disable it for now and
reactivate in .29. In .29 the hardware-branch-tracer will use the DS/BTS
facilities too - hopefully resulting in better code.
Kyle McMartin [Tue, 23 Dec 2008 13:44:30 +0000 (08:44 -0500)]
parisc: disable UP-optimized flush_tlb_mm
flush_tlb_mm's "optimized" uniprocessor case of allocating a new
context for userspace is exposing a race where we can suddely return
to a syscall with the protection id and space id out of sync, trapping
on the next userspace access.
Harry Ciao [Tue, 23 Dec 2008 21:57:16 +0000 (13:57 -0800)]
edac: fix edac core deadlock when removing a device
When deleting an edac device, we have to wait for its edac_dev.work to be
completed before deleting the whole edac_dev structure. Since we have no
idea which work in current edac_poller's workqueue is the work we are
conerned about, we wait for all work in the edac_poller's workqueue to be
proceseed. This is done via flush_cpu_workqueue() which inserts a
wq_barrier into the tail of the workqueue and then sleeping on the
completion of this wq_barrier. The edac_poller will wake up sleepers when
it is found.
EDAC core creates only one kernel worker thread, edac_poller, to run the
works of all current edac devices. They share the same callback function
of edac_device_workq_function(), which would grab the mutex of
device_ctls_mutex first before it checks the device. This is exactly
where edac_poller and rmmod would have a great chance to deadlock.
In below call trace of rmmod > ... >
edac_device_del_device >
edac_device_workq_teardown > flush_workqueue > flush_cpu_workqueue,
device_ctls_mutex would have already been grabbed by
edac_device_del_device(). So, on one hand rmmod would sleep on the
completion of a wq_barrier, holding device_ctls_mutex; on the other hand
edac_poller would be blocked on the same mutex when it's running any one
of works of existing edac evices(Note, this edac_dev.work is likely to be
totally irrelevant to the one that is being removed right now)and never
would have a chance to run the work of above wq_barrier to wake rmmod up.
edac_device_workq_teardown() should not be called within the critical
region of device_ctls_mutex. Just like is done in edac_pci_del_device()
and edac_mc_del_mc(), where edac_pci_workq_teardown() and
edac_mc_workq_teardown() are called after related mutex are released.
Moreover, an edac_dev.work should check first if it is being removed. If
this is the case, then it should bail out immediately. Since not all of
existing edac devices are to be removed, this "shutting flag" should be
contained to edac device being removed. The current edac_dev.op_state can
be used to serve this purpose.
The original deadlock problem and the solution have been witnessed and
tested on actual hardware. Without the solution, rmmod an edac driver
would result in below deadlock:
Evgeniy Polyakov [Tue, 23 Dec 2008 21:57:12 +0000 (13:57 -0800)]
w1: fix slave selection on big-endian systems
During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".
Based on a patch created by Andreas Hummel.
[akpm@linux-foundation.org: remove unneeded cast] Reported-by: Andreas Hummel <andi_hummel@gmx.de> Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
V4L/DVB (9920): em28xx: fix NULL pointer dereference in call to VIDIOC_INT_RESET command
Fix a NULL pointer dereference that would occur if the video decoder tied to
the em28xx supports the VIDIOC_INT_RESET call (for example: the cx25840 driver)
Thomas Gleixner [Sat, 20 Dec 2008 20:27:34 +0000 (21:27 +0100)]
Null pointer deref with hrtimer_try_to_cancel()
Impact: Prevent kernel crash with posix timer clockid CLOCK_MONOTONIC_RAW
commit 2d42244ae71d6c7b0884b5664cf2eda30fb2ae68 (clocksource:
introduce CLOCK_MONOTONIC_RAW) introduced a new clockid, which is only
available to read out the raw not NTP adjusted system time.
The above commit did not prevent that a posix timer can be created
with that clockid. The timer_create() syscall succeeds and initializes
the timer to a non existing hrtimer base. When the timer is deleted
either by timer_delete() or by the exit() cleanup the kernel crashes.
Prevent the creation of timers for CLOCK_MONOTONIC_RAW by setting the
posix clock function to no_timer_create which returns an error code.
Reported-and-tested-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 20 Dec 2008 19:07:31 +0000 (11:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: change simple_strtol to simple_strtoul
9p: convert d_iname references to d_name.name
9p: Remove potentially bad parameter from function entry debug print.
Linus Torvalds [Sat, 20 Dec 2008 19:07:18 +0000 (11:07 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix resume (S2R) broken by Intel microcode module, on A110L
x86 gart: don't complain if no AMD GART found
AMD IOMMU: panic if completion wait loop fails
AMD IOMMU: set cmd buffer pointers to zero manually
x86: re-enable MCE on secondary CPUS after suspend/resume
AMD IOMMU: allocate rlookup_table with __GFP_ZERO
might hang upon resuming, OTOH it should have likely hanged each and every time.
(1) possible deadlock in microcode_resume_cpu() if either 'if' section is
taken;
(2) now, I don't see it in spec. and can't experimentally verify it (newer
ucodes don't seem to be available for my Core2duo)... but logically-wise, I'd
think that when read upon resuming, the 'microcode revision' (MSR 0x8B) should
be back to its original one (we need to reload ucode anyway so it doesn't seem
logical if a cpu doesn't drop the version)... if so, the comparison with
memcmp() for the full 'struct cpu_signature' is wrong... and that's how one of
the aforementioned 'if' sections might have been triggered - leading to a
deadlock.
Obviously, in my tests I simulated loading/resuming with the ucode of the same
version (just to see that the file is loaded/re-loaded upon resuming) so this
issue has never popped up.
I'd appreciate if someone with an appropriate system might give a try to the
2nd patch (titled "fix a comparison && deadlock...").
In any case, the deadlock situation is a must-have fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
Linus Torvalds [Fri, 19 Dec 2008 19:36:04 +0000 (11:36 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: GEM on PAE has problems - disable it for now.
drm/i915: Don't return busy for buffers left on the flushing list.
Stanley Miao [Fri, 19 Dec 2008 14:08:22 +0000 (22:08 +0800)]
ALSA: Fix a Oops bug in omap soc driver.
There will be a Oops or frequent underrun messages when playing music with
omap soc driver, this is because a data region is incorretly sized, other data
region will be overwriten when writing to this data region.
Signed-off-by: Stanley Miao <stanley.miao@windriver.com> Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com> Cc: stable@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Fri, 19 Dec 2008 13:02:32 +0000 (14:02 +0100)]
ALSA: hda - Remove non-working headphone control for Dell laptops
The previous commit re-enabled hp_nid setup for IDT92HD73*, but
it's unneeded indeed for Dell laptops that have multiple headphones.
Setting the extra hp_nid results in a non-working "Headpohne" mixer
control. Thus hp_nid should be 0 for these dell models.
Also, the automatic addition of hp_nid should check whether it's
a dual-HP model or not. For dual-HPs, the pins are already checked
by the early workaround.
Wu Fengguang [Wed, 26 Nov 2008 06:35:22 +0000 (14:35 +0800)]
ACPI: don't cond_resched() when irqs_disabled()
The ACPI interpreter usually runs with irqs enabled.
However, during suspend/resume it runs with
irqs disabled to evaluate _GTS/_BFS, as well as
by irqrouter_resume() which evaluates _CRS, _PRS, _SRS.
http://bugzilla.kernel.org/show_bug.cgi?id=12252
Signed-off-by: Wu Fengguang <wfg@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Thu, 13 Nov 2008 23:30:13 +0000 (17:30 -0600)]
ACPI: fix 2.6.28 acpi.debug_level regression
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
Takashi Iwai [Wed, 17 Dec 2008 13:51:01 +0000 (14:51 +0100)]
ALSA: hda - Add no-jd model for IDT 92HD73xx
Added the model without the jack-detection for some desktops that
have really no jack-detection. The recent driver caused regressions
regarding the sound output on such machines.
cciss: fix problem that deleting multiple logical drives could cause a panic
Fix problem that deleting multiple logical drives could cause a panic.
It fixes a panic which can be easily reproduced in the following way: Just
create several "arrays," each with multiple logical drives via hpacucli,
then delete the first array, and it will blow up in deregister_disk(), in
the call to get_host() when it tries to dig the hba pointer out of a NULL
queue pointer.
The problem has been present since my code to make rebuild_lun_table
behave better went in.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
projects / mirror_ubuntu-kernels.git / log