Even though only a single concurrent remain-on-channel operation is
supported, there may be two pending remain-on-channel events (one to
indicate end of a canceled operation and another to indicate start of a
new operation). User space won't be able to distinguish these events
unless unique cookies are used.
The previous behavior resulted in wpa_supplicant getting quite
confused about the driver's offchannel state in various sequences
and this made the P2P state machine behave incorrectly. Use of
more than a single remain-on-channel cookie value fixes this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rishi Panjwani [Wed, 26 Oct 2011 02:52:41 +0000 (19:52 -0700)]
ath6kl: Implement support for power parameter control from userspace
In order to allow user space based control of power parameters, we use
available debugfs infrastructure. With these features user can control
power consumption by adjusting various sleep/wake up related parameters.
The feature has been added for testing purposes. All 5 parameters are
mandatory in correct order. They have to be written to the power_params
file. These are:
Rishi Panjwani [Wed, 26 Oct 2011 00:26:29 +0000 (17:26 -0700)]
ath6kl: Implement support for listen interval from userspace
In order to allow user space based control of listen interval, we use
available debugfs infrastructure. Listen interval implies how frequently
we want the WLAN chip to wake up and synchronize the beacons in case it
is in sleep mode. The command requires two parameters in the following order:
The user has to write the listen interval_time (in msecs) and
listen_interval_beacons (in no. of beacons) to the listen_interval file in
ath6kl debug directory.
Example:
echo "30 1" > listen_interval
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add control flag CONNECT_WPS_FLAG if a WPS IE is present in the
Association Request IEs. This flag is needed when the station must
connect to a WPS-enabled AP.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Configure inteface information at init time
Virtual interface information need to be configured during
init time to the target. With MAX_NUM_VIF is restricted to
1, currently only a single vif is being configured.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Use the other variant of netdev (un)register APIs
Use replace (un)register_netdev() with (un)register_netdevice()
so that the same ath6kl function can be used with
add_virtual_intf()/del_virtual_intf().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI ready event gives the mac address, cache this
mac address in struct ath6kl so that it can be used to
compute the mac address for other vif in case of multi vif.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use ath6kl_get_fw_iftype() to find out the
firmware interface type during initialization because the type
of the initial interface in INFRA_NETWORK. Hardcode the fw interface
type corresponding to INFRA_BSS instead of using ath6kl_get_fw_iftype().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rishi Panjwani [Wed, 19 Oct 2011 00:20:06 +0000 (17:20 -0700)]
ath6kl: Implement support for background scan control from userspace
In order to allow user space based control of background scan interval,
we use available debugfs infrastructure. The feature has been added for
testing purposes. The user has to write the bgscan interval (in secs) to
the bgscan_interval file in ath6kl debug directory. To disable bgscan,
a '0' is to be written to the bgscan_interval file.
Example:
echo "2" > bgscan_interval
This will make the background scan interval as 2 seconds
kvalo: changed implementation so that there's only one call to
ath6kl_wmi_scanparams_cmd()
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Thu, 13 Oct 2011 12:21:53 +0000 (15:21 +0300)]
ath6kl: add debug level for hif
That way we htc level debug messages can be removed from hif files. Also
add few new messages and remove useless debug message about using
synchrous irq processing (we don't support anything else).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Thu, 13 Oct 2011 12:21:45 +0000 (15:21 +0300)]
ath6kl: don't dump full htc packets
It's currently possible to dump full sdio packets, so dumping htc packets
is not strictly needed. So remove it, we can always add it back if
there ever comes a need for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rishi Panjwani [Sat, 15 Oct 2011 00:48:07 +0000 (17:48 -0700)]
ath6kl: Implement support for QOS-enable and QOS-disable from userspace
In order to allow user space based QOS control we use the available debugfs
infrastructure. With this feature, user can make changes to qos parameters,
thereby allowing creation and deletion of user defined priority streams and
features like uapsd. This feature has been added for testing purposes.
All 21 parameters for the create_qos command are mandatory in the correct
order. They have to be written to the create_qos file in
the ath6kl debug directory. These parameters(in order) are:
1)user priority
2)direction
3)traffic class
4)traffic type
5)voice PS capability
6)min service intvl
7)max service intvl
8)inactivity intvl
9)suspension intvl
10)serv start time
11)tsid
12)nominal msdu
13)max msdu
14)min data rate
15)mean data rate
16)peak data rate
17)max burst size
18)delay bound
19)min phy rate
20)surplus bw allowance
21)medium time
The previous version did not really make much sense and the theoretical
maximum length would be a bit longer. Calculate the length more
accurately. In addition, there is no need to clear the buffer, so use
kmalloc instead of kzalloc. For bonus points, add the forgotten
cred_rpt_from_other value to the file.
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Wed, 12 Oct 2011 06:58:28 +0000 (09:58 +0300)]
ath6kl: fix firmware start address for ar6003 hw2.0
Sangwook found out that commit 639d0b89 ("ath6kl: read firmware start
address from hardware") broke firmware boot on ar6003 hw2.0 as it seems
it's not posible to automatically query the address from hardware. So
we need to hardcode the address for hw2.0.
Reported-by: Sangwook Lee <sangwook.lee@linaro.org> Tested-by: Sangwook Lee <sangwook.lee@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jouni Malinen [Tue, 11 Oct 2011 14:31:56 +0000 (17:31 +0300)]
ath6kl: Add debugfs control for keepalive and disconnection timeout
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jouni Malinen [Tue, 11 Oct 2011 14:31:55 +0000 (17:31 +0300)]
ath6kl: Add debugfs files for roaming control
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kevin Fang [Fri, 7 Oct 2011 00:51:19 +0000 (08:51 +0800)]
ath6kl: Add WSC IE on the associate message
For some WPS test items, such as item "5.1.14"
STAUT must include the WSC IE in the 802.11 Association Request frame.
Therefore, add the corresponding IE in association message.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chilam Ng [Wed, 5 Oct 2011 07:12:52 +0000 (10:12 +0300)]
ath6kl: make sure WLAN power save is enabled during suspend
Power save is enabled during ath6kl init. But when user space disables power
save, the system will go into suspend with power save disabled. The ath6kl
driver will now explicitly enable power save prior to entering suspend and
restore its previous setting upon resume
Signed-off-by: Chilam Ng <chilamng@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Fix htc_packet leak in ath6kl_htc_rx_process_packets()
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Claim sdio function only at appropriate places
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Replace spin_lock_irqsave with spin_lock_bh
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: Enable force foreground scan in connected state
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Dan Carpenter [Tue, 8 Nov 2011 03:31:47 +0000 (19:31 -0800)]
mwifiex: prevent corruption instead of just warning
Probably we never hit this condition, but in case we do, we may as
well put a return here instead of just printing a warning message and
then corrupting memory. The caller doesn't check the return code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 8 Nov 2011 03:31:45 +0000 (19:31 -0800)]
mwifiex: remove an unneeded NULL check
We dereference adapter in the error handling code so this needed to
be fixed. This function is always called like:
adapter->if_ops.host_to_card(adapter, ...);
so adapter can never be NULL and I've removed the NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 8 Nov 2011 03:31:44 +0000 (19:31 -0800)]
mwifiex: remove unneeded kfree(NULL);
The previous if statement means this that pointer is NULL so there
is no need to free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:42 +0000 (22:23 +0100)]
brcm80211: fmac: optimize chip core info management
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:41 +0000 (22:23 +0100)]
brcm80211: fmac: replace private SB macros with ssb_regs version
Use SSB macros in order to clean up brcmfmac code
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:40 +0000 (22:23 +0100)]
brcm80211: fmac: move chip drive strength related code to sdio_chip.c
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:39 +0000 (22:23 +0100)]
brcm80211: fmac: move chip detach function to sdio_chip.c
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:38 +0000 (22:23 +0100)]
brcm80211: fmac: move chip reset core function to sdio_chip.c
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:37 +0000 (22:23 +0100)]
brcm80211: fmac: abstract chip core revision function
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:36 +0000 (22:23 +0100)]
brcm80211: fmac: abstract chip iscoreup function
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:35 +0000 (22:23 +0100)]
brcm80211: fmac: chip attach code flow clean up
Merged brcmf_sdbrcm_chip_attach into brcmf_sdio_chip_attach
for better readability.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:34 +0000 (22:23 +0100)]
brcm80211: fmac: remove duplicate regiter set in chip attach path
Same register writes have been done in brcmf_sdbrcm_probe_init
which is earlier in the same code path.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:33 +0000 (22:23 +0100)]
brcm80211: fmac: move dongle gpio reset code to chip attach function
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:32 +0000 (22:23 +0100)]
brcm80211: fmac: disable dongle arm core in bus core setup function
This will provide a better code flow that fits the logic
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:31 +0000 (22:23 +0100)]
brcm80211: fmac: move core disable function to sdio_chip.c
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:30 +0000 (22:23 +0100)]
brcm80211: fmac: abstract chip buscore setup function
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:29 +0000 (22:23 +0100)]
brcm80211: fmac: move bus core prep code to sdio_chip.c
This patch is part of abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 4 Nov 2011 21:23:28 +0000 (22:23 +0100)]
brcm80211: fmac: move chip recognition function to sdio_chip.c
Currently backplane handle code is scatterd around dhd_sdio.c which
is not good for maintenance and adding new backplane interconnect
type support. This patch and the follow up patches are going to
abstract all chip backplane control code specific for sdio bus
into this new sdio_chip.c
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / mirror_ubuntu-jammy-kernel.git / log