It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fde6 ("r8169: remove rtl8169_set_speed_xmii") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reported-by: Neil MacLeod <neil@nmacleod.com> Tested-by: Neil MacLeod <neil@nmacleod.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Thu, 20 Sep 2018 09:27:28 +0000 (17:27 +0800)]
sctp: update dst pmtu with the correct daddr
When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.
However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.
So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.
The issue has existed since route exceptions introduction.
Fixes: 4895c771c7f0 ("ipv4: Add FIB nexthop exceptions.") Reported-by: ian.periam@dialogic.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:31:45 +0000 (09:31 +0300)]
mlxsw: spectrum: Bump required firmware version
MC-aware mode was introduced to mlxsw in commit 7b8195306694 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit 3a3539cd3632 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports") Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add missing device config for RoCE EDPM in UFP mode.
This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Do not add VLAN 0 tag to untagged frames in multi-function mode.
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Fix populating the invalid stag value in multi function mode.
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 19 Sep 2018 13:29:06 +0000 (15:29 +0200)]
net: mvneta: fix the Rx desc buffer DMA unmapping
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 19 Sep 2018 13:02:07 +0000 (15:02 +0200)]
ip6_tunnel: be careful when accessing the inner header
the ip6 tunnel xmit ndo assumes that the processed skb always
contains an ip[v6] header, but syzbot has found a way to send
frames that fall short of this assumption, leading to the following splat:
This change addresses the issue adding the needed check before
accessing the inner header.
The ipv4 side of the issue is apparently there since the ipv4 over ipv6
initial support, and the ipv6 side predates git history.
Fixes: c4d3efafcc93 ("[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+3fde91d4d394747d6db4@syzkaller.appspotmail.com Tested-by: Alexander Potapenko <glider@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Sep 2018 03:32:46 +0000 (20:32 -0700)]
Merge tag 'batadv-net-for-davem-20180919' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
pull request for net: batman-adv 2018-09-19
here are some bugfixes which we would like to see integrated into net.
We forgot to bump the version number in the last round for net-next, so
the belated patch to do that is included - we hope you can adopt it.
This will most likely create a merge conflict later when merging into
net-next with this rounds net-next patchset, but net-next should keep
the 2018.4 version[1].
====================
ipv6: fix issues on accessing fib6_metrics
The latest fix on the memory leak of fib6_metrics still causes
use-after-free.
This patch series first revert the previous fix and propose a new fix
that is more inline with ipv4 logic and is tested to fix the
use-after-free issue reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Tue, 18 Sep 2018 20:45:00 +0000 (13:45 -0700)]
ipv6: fix memory leak on dst->_metrics
When dst->_metrics and f6i->fib6_metrics share the same memory, both
take reference count on the dst_metrics structure. However, when dst is
destroyed, ip6_dst_destroy() only invokes dst_destroy_metrics_generic()
which does not take care of READONLY metrics and does not release refcnt.
This causes memory leak.
Similar to ipv4 logic, the fix is to properly release refcnt and free
the memory space pointed by dst->_metrics if refcnt becomes 0.
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change causes use-after-free on dst->_metrics.
The crash trace looks like this:
[ 97.763269] BUG: KASAN: use-after-free in ip6_mtu+0x116/0x140
[ 97.769038] Read of size 4 at addr ffff881781d2cf84 by task svw_NetThreadEv/8801
Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 18 Sep 2018 15:48:53 +0000 (16:48 +0100)]
sfp: fix oops with ethtool -m
If a network interface is created prior to the SFP socket being
available, ethtool can request module information. This unfortunately
leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = (ptrval)
[00000008] *pgd=7c400831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1480 Comm: ethtool Not tainted 4.19.0-rc3 #138
Hardware name: Broadcom Northstar Plus SoC
PC is at sfp_get_module_info+0x8/0x10
LR is at dev_ethtool+0x218c/0x2afc
Fix this by not filling in the network device's SFP bus pointer until
SFP is fully bound, thereby avoiding the core calling into the SFP bus
code.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Reported-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 18 Sep 2018 14:58:47 +0000 (16:58 +0200)]
net: mvpp2: fix a txq_done race condition
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09e2 ("net: mvpp2: replace TX coalescing interrupts with hrtimer") Reported-by: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kernel_sendmsg can return a negative
error code.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don't check a listen socket for pending urgent data in smc_poll().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: enable fallback for connection abort in state INIT
If a linkgroup is terminated abnormally already due to failing
LLC CONFIRM LINK or LLC ADD LINK, fallback to TCP is still possible.
In this case do not switch to state SMC_PEERABORTWAIT and do not set
sk_err.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For a failing smc_listen_rdma_finish() smc_listen_decline() is
called. If fallback is possible, the new socket is already enqueued
to be accepted in smc_listen_decline(). Avoid enqueuing a second time
afterwards in this case, otherwise the smc_create_lgr_pending lock
is released twice:
[ 373.463976] WARNING: bad unlock balance detected!
[ 373.463978] 4.18.0-rc7+ #123 Tainted: G O
[ 373.463979] -------------------------------------
[ 373.463980] kworker/1:1/30 is trying to release lock (smc_create_lgr_pending) at:
[ 373.463990] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.463991] but there are no more locks to release!
[ 373.463991]
other info that might help us debug this:
[ 373.463993] 2 locks held by kworker/1:1/30:
[ 373.463994] #0: 00000000772cbaed ((wq_completion)"events"){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464000] #1: 000000003ad0894a ((work_completion)(&new_smc->smc_listen_work)){+.+.}, at: process_one_work+0x1ec/0x6b0
[ 373.464003]
stack backtrace:
[ 373.464005] CPU: 1 PID: 30 Comm: kworker/1:1 Kdump: loaded Tainted: G O 4.18.0-rc7uschi+ #123
[ 373.464007] Hardware name: IBM 2827 H43 738 (LPAR)
[ 373.464010] Workqueue: events smc_listen_work [smc]
[ 373.464011] Call Trace:
[ 373.464015] ([<0000000000114100>] show_stack+0x60/0xd8)
[ 373.464019] [<0000000000a8c9bc>] dump_stack+0x9c/0xd8
[ 373.464021] [<00000000001dcaf8>] print_unlock_imbalance_bug+0xf8/0x108
[ 373.464022] [<00000000001e045c>] lock_release+0x114/0x4f8
[ 373.464025] [<0000000000aa87fa>] __mutex_unlock_slowpath+0x4a/0x300
[ 373.464027] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc]
[ 373.464029] [<0000000000197a68>] process_one_work+0x2a8/0x6b0
[ 373.464030] [<0000000000197ec2>] worker_thread+0x52/0x410
[ 373.464033] [<000000000019fd0e>] kthread+0x15e/0x178
[ 373.464035] [<0000000000aaf58a>] kernel_thread_starter+0x6/0xc
[ 373.464052] [<0000000000aaf584>] kernel_thread_starter+0x0/0xc
[ 373.464054] INFO: lockdep is turned off.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In state SMC_INIT smc_poll() delegates polling to the internal
CLC socket. This means, once the connect worker has finished
its kernel_connect() step, the poll wake-up may occur. This is not
intended. The wake-up should occur from the wake up call in
smc_connect_work() after __smc_connect() has finished.
Thus in state SMC_INIT this patch now calls sock_poll_wait() on the
main SMC socket.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: \91nvm_param.dir_type\92 may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: emac: fix fixed-link setup for the RTL8363SB switch
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to ETSI TS 102 622 specification chapter 4.4 pipe identifier
is 7 bits long which allows for 128 unique pipe IDs. Because
NFC_HCI_MAX_PIPES is used as the number of pipes supported and not
as the max pipe ID, its value should be 128 instead of 127.
nfc_hci_recv_from_llc extracts pipe ID from packet header using
NFC_HCI_FRAGMENT(0x7F) mask which allows for pipe ID value of 127.
Same happens when NCI_HCP_MSG_GET_PIPE() is being used. With
pipes array having only 127 elements and pipe ID of 127 the OOB memory
access will result.
Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Allen Pais <allen.pais@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
NFC: Fix possible memory corruption when handling SHDLC I-Frame commands
When handling SHDLC I-Frame commands "pipe" field used for indexing
into an array should be checked before usage. If left unchecked it
might access memory outside of the array of size NFC_HCI_MAX_PIPES(127).
Malformed NFC HCI frames could be injected by a malicious NFC device
communicating with the device being attacked (remote attack vector),
or even by an attacker with physical access to the I2C bus such that
they could influence the data transfers on that bus (local attack vector).
skb->data is controlled by the attacker and has only been sanitized in
the most trivial ways (CRC check), therefore we can consider the
create_info struct and all of its members to tainted. 'create_info->pipe'
with max value of 255 (uint8) is used to take an offset of the
hdev->pipes array of 127 elements which can lead to OOB write.
Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Allen Pais <allen.pais@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Kevin Deus <kdeus@google.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: pmtu: properly redirect stderr to /dev/null
The cleanup function uses "$CMD 2 > /dev/null", which doesn't actually
send stderr to /dev/null, so when the netns doesn't exist, the error
message is shown. Use "2> /dev/null" instead, so that those messages
disappear, as was intended.
Fixes: d1f1b9cbf34c ("selftests: net: Introduce first PMTU test") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Mon, 17 Sep 2018 08:22:57 +0000 (09:22 +0100)]
net: stmmac: Fixup the tail addr setting in xmit path
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Fixes: f748be531d70 ("stmmac: support new GMAC4") Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Mon, 17 Sep 2018 08:22:56 +0000 (09:22 +0100)]
net: stmmac: Rework coalesce timer and fix multi-queue races
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Fixes: ce736788e8a ("net: stmmac: adding multiple buffers for TX") Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
Peter Oskolkov [Mon, 17 Sep 2018 17:20:53 +0000 (10:20 -0700)]
net/ipv6: do not copy dst flags on rt init
DST_NOCOUNT in dst_entry::flags tracks whether the entry counts
toward route cache size (net->ipv6.sysctl.ip6_rt_max_size).
If the flag is NOT set, dst_ops::pcpuc_entries counter is incremented
in dist_init() and decremented in dst_destroy().
This flag is tied to allocation/deallocation of dst_entry and
should not be copied from another dst/route. Otherwise it can happen
that dst_ops::pcpuc_entries counter grows until no new routes can
be allocated because the counter reached ip6_rt_max_size due to
DST_NOCOUNT not set and thus no counter decrements on gc-ed routes.
Fixes: 3b6761d18bc1 ("net/ipv6: Move dst flags to booleans in fib entries") Cc: David Ahern <dsahern@gmail.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: Peter Oskolkov <posk@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com> Reported-by: Deshu Wen <dwen@sierrawireless.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Reported-by: Fred Veldini <fred.veldini@gmail.com> Reported-by: Deshu Wen <dwen@sierrawireless.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Sep 2018 01:47:58 +0000 (18:47 -0700)]
Merge branch 'r8169-clk-fixes'
Hans de Goede says:
====================
r8169 (x86) clk fixes to fix S0ix not being reached
This series adds code to the r8169 ethernet driver to get and enable an
external clock if present, avoiding the need for a hack in the
clk-pmc-atom driver where that clock was left on continuesly causing x86
some devices to not reach deep power saving states (S0ix) when suspended
causing to them to quickly drain their battery while suspended.
The 3 commits in this series need to be merged in order to avoid
regressions while bisecting. The clk-pmc-atom driver does not see much
changes (it was last touched over a year ago). So the clk maintainers
have agreed with merging all 3 patches through the net tree.
All 3 patches have Stephen Boyd's Acked-by for this purpose.
This v2 of the series only had some minor tweaks done to the commit
messages and is ready for merging through the net tree now.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:56 +0000 (11:34 +0200)]
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware"), which added the code to mark clocks as CLK_IS_CRITICAL, causes
all unclaimed PMC clocks on Cherry Trail devices to be on all the time,
resulting on the device not being able to reach S0i3 when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the r8169 ethernet controller uses pmc_plt_clk_4. Now that the clk-pmc-atom
driver exports an "ether_clk" alias for pmc_plt_clk_4 and the r8169 driver
has been modified to get and enable this clock (if present) the marking of
the clocks as CLK_IS_CRITICAL is no longer necessary.
This commit removes the CLK_IS_CRITICAL marking, fixing Cherry Trail
devices not being able to reach S0i3 greatly decreasing their battery
drain when suspended.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:55 +0000 (11:34 +0200)]
r8169: Get and enable optional ether_clk clock
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f9a ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede [Wed, 12 Sep 2018 09:34:54 +0000 (11:34 +0200)]
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
Commit d31fd43c0f9a ("clk: x86: Do not gate clocks enabled by the
firmware") causes all unclaimed PMC clocks on Cherry Trail devices to be on
all the time, resulting on the device not being able to reach S0i2 or S0i3
when suspended.
The reason for this commit is that on some Bay Trail / Cherry Trail devices
the ethernet controller uses pmc_plt_clk_4. This commit adds an "ether_clk"
alias, so that the relevant ethernet drivers can try to (optionally) use
this, without needing X86 specific code / hacks, thus fixing ethernet on
these devices without breaking S0i3 support.
This commit uses clkdev_hw_create() to create the alias, mirroring the code
for the already existing "mclk" alias for pmc_plt_clk_3.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102 Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861 Cc: Johannes Stezenbach <js@sig21.net> Cc: Carlo Caione <carlo@endlessm.com> Reported-by: Johannes Stezenbach <js@sig21.net> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: Align ASPM/CLKREQ setting function with vendor driver
There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes kcm users know they need to look for the
strparser offset within their bpf program, which is not documented
anywhere and examples laying around do not do.
The actual recv function does handle the offset well, so we can create a
temporary clone of the skb and pull that one up as required for parsing.
The pull itself has a cost if we are pulling beyond the head data,
measured to 2-3% latency in a noisy VM with a local client stressing
that path. The clone's impact seemed too small to measure.
This bug can be exhibited easily by implementing a "trivial" kcm parser
taking the first bytes as size, and on the client sending at least two
such packets in a single write().
Note that bpf sockmap has the same problem, both for parse and for recv,
so it would pulling twice or a real pull within the strparser logic if
anyone cares about that.
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Check for SQ and not RQ state when modifying hairpin SQ
When modifying hairpin SQ, instead of checking if the next state equals
to MLX5_SQC_STATE_RDY, we compare it against the MLX5_RQC_STATE_RDY enum
value.
The code worked since both of MLX5_RQC_STATE_RDY and MLX5_SQC_STATE_RDY
have the same value today.
Eli Cohen [Sun, 2 Sep 2018 09:01:53 +0000 (12:01 +0300)]
net/mlx5: Fix read from coherent memory
Use accessor function READ_ONCE to read from coherent memory modified
by the device and read by the driver. This becomes most important in
preemptive kernels where cond_resched implementation does not have the
side effect which guaranteed the updated value.
Merge tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
drivers/net/ethernet/microchip/lan743x_main.c:2964:12: warning: \91lan743x_pm_suspend\92 defined but not used [-Wunused-function]
static int lan743x_pm_suspend(struct device *dev)
drivers/net/ethernet/microchip/lan743x_main.c:2987:12: warning: \91lan743x_pm_resume\92 defined but not used [-Wunused-function]
static int lan743x_pm_resume(struct device *dev)
Signed-off-by: zhong jiang <zhongjiang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 14 Sep 2018 21:46:12 +0000 (23:46 +0200)]
net: dsa: mv88e6xxx: Fix ATU Miss Violation
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c5005 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from strace, there are two TLS records sent,
i) 'test_read_peek' and ii) '_mult_recs\0' where we end up
peeking 'test_read_peektest_read_peektest'. This is clearly
wrong, and what happens is that given peek cannot call into
tls_sw_advance_skb() to unpause strparser and proceed with
the next skb, we end up looping over the current one, copying
the 'test_read_peek' over and over into the user provided
buffer.
Here, we can only peek into the currently held skb (current,
full TLS record) as otherwise we would end up having to hold
all the original skb(s) (depending on the peek depth) in a
separate queue when unpausing strparser to process next
records, minimally intrusive is to return only up to the
current record's size (which likely was what c46234ebb4d1
("tls: RX path for ktls") originally intended as well). Thus,
after patch we properly peek the first record:
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
hv_netvsc: associate VF and PV device by serial number
The Hyper-V implementation of PCI controller has concept of 32 bit serial number
(not to be confused with PCI-E serial number). This value is sent in the protocol
from the host to indicate SR-IOV VF device is attached to a synthetic NIC.
Using the serial number (instead of MAC address) to associate the two devices
avoids lots of potential problems when there are duplicate MAC addresses from
tunnels or layered devices.
The patch set is broken into two parts, one is for the PCI controller
and the other is for the netvsc device. Normally, these go through different
trees but sending them together here for better review. The PCI changes
were submitted previously, but the main review comment was "why do you
need this?". This is why.
v2 - slot name can be shorter.
remove locking when creating pci_slots; see comment for explaination
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching network device based on MAC address is problematic
since a non VF network device can be creted with a duplicate MAC
address causing confusion and problems. The VMBus API does provide
a serial number that is a better matching method.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI: hv: support reporting serial number as slot information
The Hyper-V host API for PCI provides a unique "serial number" which
can be used as basis for sysfs PCI slot table. This can be useful
for cases where userspace wants to find the PCI device based on
serial number.
When an SR-IOV NIC is added, the host sends an attach message
with serial number. The kernel doesn't use the serial number, but
it is useful when doing the same thing in a userspace driver such
as the DPDK. By having /sys/bus/pci/slots/N it provides a direct
way to find the matching PCI device.
There maybe some cases where serial number is not unique such
as when using GPU's. But the PCI slot infrastructure will handle
that.
This has a side effect which may also be useful. The common udev
network device naming policy uses the slot information (rather
than PCI address).
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 14 Sep 2018 19:41:29 +0000 (15:41 -0400)]
bnxt_en: Fix VF mac address regression.
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e966026 ("bnxt_en: Always forward VF MAC address to the PF.") Reported-by: Seth Forshee <seth.forshee@canonical.com> Reported-by: Siwei Liu <loseweigh@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 14 Sep 2018 19:02:31 +0000 (12:02 -0700)]
ipv6: fix possible use-after-free in ip6_xmit()
In the unlikely case ip6_xmit() has to call skb_realloc_headroom(),
we need to call skb_set_owner_w() before consuming original skb,
otherwise we risk a use-after-free.
Bring IPv6 in line with what we do in IPv4 to fix this.
Fixes: 1da177e4c3f41 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Fri, 14 Sep 2018 16:39:53 +0000 (17:39 +0100)]
net: hp100: fix always-true check for link up state
The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value
that is always non-zero and hence the wait for the link to drop always
terminates prematurely. Fix this by using a logical not operator instead
of a bitwise complement. This issue has been in the driver since
pre-2.6.12-rc2.
Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 14 Sep 2018 15:48:11 +0000 (17:48 +0200)]
ARM: dts: at91: add new compatibility string for macb on sama5d3
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 14 Sep 2018 15:48:10 +0000 (17:48 +0200)]
net: macb: disable scatter-gather for macb on sama5d3
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 14 Sep 2018 14:56:35 +0000 (16:56 +0200)]
net: mvpp2: let phylink manage the carrier state
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb043262878 ("net: mvpp2: phylink support") Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pppoe_rcv() needs to look back at the Ethernet header in order to
lookup the PPPoE session. Therefore we need to ensure that the mac
header is big enough to contain an Ethernet header. Otherwise
eth_hdr(skb)->h_source might access invalid data.
Fixes: 224cf5ad14c0 ("ppp: Move the PPP drivers") Reported-by: syzbot+f5f6080811c849739212@syzkaller.appspotmail.com Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mades TI_DAVINCI_CPDMA select GENERIC_ALLOCATOR.
without that, the following sparc64 build failure happen
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
(.text+0x278): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit':
(.text+0x340): undefined reference to `gen_pool_alloc'
(.text+0x5c4): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x64c): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.6':
davinci_cpdma.c:(.text+0x17ac): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x17b8): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x1824): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x1830): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
(.text+0x19f8): undefined reference to `devm_gen_pool_create'
(.text+0x1a90): undefined reference to `gen_pool_add_virt'
Makefile:1011: recipe for target 'vmlinux' failed
Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Ted writes:
Various ext4 bug fixes; primarily making ext4 more robust against
maliciously crafted file systems, and some DAX fixes.
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4, dax: set ext4_dax_aops for dax files
ext4, dax: add ext4_bmap to ext4_dax_aops
ext4: don't mark mmp buffer head dirty
ext4: show test_dummy_encryption mount option in /proc/mounts
ext4: close race between direct IO and ext4_break_layouts()
ext4: fix online resizing for bigalloc file systems with a 1k block size
ext4: fix online resize's handling of a too-small final block group
ext4: recalucate superblock checksum after updating free blocks/inodes
ext4: avoid arithemetic overflow that can trigger a BUG
ext4: avoid divide by zero fault when deleting corrupted inline directories
ext4: check to make sure the rename(2)'s destination is not freed
ext4: add nonstring annotations to ext4.h
Merge tag 'linux-kselftest-4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pulled kselftest fixes from Shuah:
"This Kselftest fixes update for 4.9-rc5 consists of:
-- fixes to build failures
-- fixes to add missing config files to increase test coverage
-- fixes to cgroup test and a new cgroup test for memory.oom.group"
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix end boundary calculation in BTF for the type section, from Martin.
2) Fix and revert subtraction of pointers that was accidentally allowed
for unprivileged programs, from Alexei.
3) Fix bpf_msg_pull_data() helper by using __GFP_COMP in order to avoid
a warning in linearizing sg pages into a single one for large allocs,
from Tushar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid this, orphan the skb before entering GRO.
Fixes: 948d4f214fde ("veth: Add driver XDP") Reported-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Tested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
udp: add missing check on edumx rx path
The early demux RX path for the UDP protocol is currently missing
some checks. Both ipv4 and ipv6 implementations lack checksum conversion
and the ipv6 implementation additionally lack the zero checksum
validation.
The first patch takes care of UDPv4 and the second one of UDPv6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 13 Sep 2018 14:27:21 +0000 (16:27 +0200)]
udp6: add missing checks on edumux packet processing
Currently the UDPv6 early demux rx code path lacks some mandatory
checks, already implemented into the normal RX code path - namely
the checksum conversion and no_check6_rx check.
Similar to the previous commit, we move the common processing to
an UDPv6 specific helper and call it from both edemux code path
and normal code path. In respect to the UDPv4, we need to add an
explicit check for non zero csum according to no_check6_rx value.
Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Xin Long <lucien.xin@gmail.com> Fixes: c9f2c1ae123a ("udp6: fix socket leak on early demux") Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 13 Sep 2018 14:27:20 +0000 (16:27 +0200)]
udp4: fix IP_CMSG_CHECKSUM for connected sockets
commit 2abb7cdc0dc8 ("udp: Add support for doing checksum
unnecessary conversion") left out the early demux path for
connected sockets. As a result IP_CMSG_CHECKSUM gives wrong
values for such socket when GRO is not enabled/available.
This change addresses the issue by moving the csum conversion to a
common helper and using such helper in both the default and the
early demux rx path.
Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jongsung Kim [Thu, 13 Sep 2018 09:32:21 +0000 (18:32 +0900)]
stmmac: fix valid numbers of unicast filter entries
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Code of Conflict is not achieving its implicit goal of fostering
civility and the spirit of 'be excellent to each other'. Explicit
guidelines have demonstrated success in other projects and other areas
of the kernel.
Here is a Code of Conduct statement for the wider kernel. It is based
on the Contributor Covenant as described at www.contributor-covenant.org
From this point forward, we should abide by these rules in order to help
make the kernel community a welcoming environment to participate in.
Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Olof Johansson <olof@lxom.net> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sync syscall to DAX file needs to flush processor cache, but it
currently does not flush to existing DAX files. This is because
'ext4_da_aops' is set to address_space_operations of existing DAX
files, instead of 'ext4_dax_aops', since S_DAX flag is set after
ext4_set_aops() in the open path.
New file
--------
lookup_open
ext4_create
__ext4_new_inode
ext4_set_inode_flags // Set S_DAX flag
ext4_set_aops // Set aops to ext4_dax_aops
Existing file
-------------
lookup_open
ext4_lookup
ext4_iget
ext4_set_aops // Set aops to ext4_da_aops
ext4_set_inode_flags // Set S_DAX flag
Change ext4_iget() to initialize i_flags before ext4_set_aops().
Fixes: 5f0663bb4a64 ("ext4, dax: introduce ext4_dax_aops") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Suggested-by: Jan Kara <jack@suse.cz> Cc: stable@vger.kernel.org
Ext4 mount path calls .bmap to the journal inode. This currently
works for the DAX mount case because ext4_iget() always set
'ext4_da_aops' to any regular files.
In preparation to fix ext4_iget() to set 'ext4_dax_aops' for ext4
DAX files, add ext4_bmap() to 'ext4_dax_aops', since bmap works for
DAX inodes.
Fixes: 5f0663bb4a64 ("ext4, dax: introduce ext4_dax_aops") Signed-off-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Suggested-by: Jan Kara <jack@suse.cz> Cc: stable@vger.kernel.org
Li Dongyang [Sat, 15 Sep 2018 21:11:25 +0000 (17:11 -0400)]
ext4: don't mark mmp buffer head dirty
Marking mmp bh dirty before writing it will make writeback
pick up mmp block later and submit a write, we don't want the
duplicate write as kmmpd thread should have full control of
reading and writing the mmp block.
Another reason is we will also have random I/O error on
the writeback request when blk integrity is enabled, because
kmmpd could modify the content of the mmp block(e.g. setting
new seq and time) while the mmp block is under I/O requested
by writeback.
Signed-off-by: Li Dongyang <dongyangli@ddn.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Cc: stable@vger.kernel.org
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingol Molnar:
"Misc fixes:
- EFI crash fix
- Xen PV fixes
- do not allow PTI on 2-level 32-bit kernels for now
- documentation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/APM: Fix build warning when PROC_FS is not enabled
Revert "x86/mm/legacy: Populate the user page-table with user pgd's"
x86/efi: Load fixmap GDT in efi_call_phys_epilog() before setting %cr3
x86/xen: Disable CPU0 hotplug for Xen PV
x86/EISA: Don't probe EISA bus for Xen PV guests
x86/doc: Fix Documentation/x86/earlyprintk.txt
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: various scheduler metrics corner case fixes, a
sched_features deadlock fix, and a topology fix for certain NUMA
systems"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix kernel-doc notation warning
sched/fair: Fix load_balance redo for !imbalance
sched/fair: Fix scale_rt_capacity() for SMT
sched/fair: Fix vruntime_normalized() for remote non-migration wakeup
sched/pelt: Fix update_blocked_averages() for RT and DL classes
sched/topology: Set correct NUMA topology type
sched/debug: Fix potential deadlock when writing to sched_features
Randy Dunlap [Fri, 14 Sep 2018 22:10:29 +0000 (15:10 -0700)]
x86/APM: Fix build warning when PROC_FS is not enabled
Fix build warning in apm_32.c when CONFIG_PROC_FS is not enabled:
../arch/x86/kernel/apm_32.c:1643:12: warning: 'proc_apm_show' defined but not used [-Wunused-function]
static int proc_apm_show(struct seq_file *m, void *v)
Fixes: 3f3942aca6da ("proc: introduce proc_create_single{,_data}") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Jiri Kosina <jikos@kernel.org> Link: https://lkml.kernel.org/r/be39ac12-44c2-4715-247f-4dcc3c525b8b@infradead.org
Merge tag '4.19-rc3-smb3-cifs' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Fixes for four CIFS/SMB3 potential pointer overflow issues, one minor
build fix, and a build warning cleanup"
* tag '4.19-rc3-smb3-cifs' of git://git.samba.org/sfrench/cifs-2.6:
cifs: read overflow in is_valid_oplock_break()
cifs: integer overflow in in SMB2_ioctl()
CIFS: fix wrapping bugs in num_entries()
cifs: prevent integer overflow in nxt_dir_entry()
fs/cifs: require sha512
fs/cifs: suppress a string overflow warning
Merge tag 'nfs-for-4.19-2' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client bugfixes from Anna Schumaker:
"These are a handful of fixes for problems that Trond found. Patch #1
and #3 have the same name, a second issue was found after applying the
first patch.
Stable bugfixes:
- v4.17+: Fix tracepoint Oops in initiate_file_draining()
- v4.11+: Fix an infinite loop on I/O
Other fixes:
- Return errors if a waiting layoutget is killed
- Don't open code clearing of delegation state"
* tag 'nfs-for-4.19-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFS: Don't open code clearing of delegation state
NFSv4.1 fix infinite loop on I/O.
NFSv4: Fix a tracepoint Oops in initiate_file_draining()
pNFS: Ensure we return the error if someone kills a waiting layoutget
NFSv4: Fix a tracepoint Oops in initiate_file_draining()
Merge tag 'trace-v4.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"This fixes an issue with the build system caused by a change that
modifies CC_FLAGS_FTRACE. The issue is that it breaks the dependencies
and causes "make targz-pkg" to rebuild the entire world"
* tag 'trace-v4.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/Makefile: Fix handling redefinition of CC_FLAGS_FTRACE
Merge tag 'devicetree-fixes-for-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fix from Rob Herring:
"One regression for a 20 year old PowerMac:
- Fix a regression on systems having a DT without any phandles which
happens on a PowerMac G3"
* tag 'devicetree-fixes-for-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: fix phandle cache creation for DTs with no phandles
Merge tag 'for-linus-4.19c-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains some minor cleanups and fixes:
- a new knob for controlling scrubbing of pages returned by the Xen
balloon driver to the Xen hypervisor to address a boot performance
issue seen in large guests booted pre-ballooned
- a fix of a regression in the gntdev driver which made it impossible
to use fully virtualized guests (HVM guests) with a 4.19 based dom0
- a fix in Xen cpu hotplug functionality which could be triggered by
wrong admin commands (setting number of active vcpus to 0)
One further note: the patches have all been under test for several
days in another branch. This branch has been rebased in order to avoid
merge conflicts"
* tag 'for-linus-4.19c-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gntdev: fix up blockable calls to mn_invl_range_start
xen: fix GCC warning and remove duplicate EVTCHN_ROW/EVTCHN_COL usage
xen: avoid crash in disable_hotplug_cpu
xen/balloon: add runtime control for scrubbing ballooned out pages
xen/manage: don't complain about an empty value in control/sysrq node
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The trickle of arm64 fixes continues to come in.
Nothing that's the end of the world, but we've got a fix for PCI IO
port accesses, an accidental naked "asm goto" and a fix to the
vmcoreinfo PT_NOTE merged this time around which we'd like to get
sorted before it becomes ABI.
- Fix ioport_map() mapping the wrong physical address for some I/O
BARs
- Remove direct use of "asm goto", since some compilers don't like
that
- Ensure kimage_voffset is always present in vmcoreinfo PT_NOTE"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
asm-generic: io: Fix ioport_map() for !CONFIG_GENERIC_IOMAP && CONFIG_INDIRECT_PIO
arm64: kernel: arch_crash_save_vmcoreinfo() should depend on CONFIG_CRASH_CORE
arm64: jump_label.h: use asm_volatile_goto macro instead of "asm goto"
The previous fix broke recovery of delegated stateids because it assumes
that if we did not mark the delegation as suspect, then the delegation has
effectively been revoked, and so it removes that delegation irrespectively
of whether or not it is valid and still in use. While this is "mostly
harmless" for ordinary I/O, we've seen pNFS fail with LAYOUTGET spinning
in an infinite loop while complaining that we're using an invalid stateid
(in this case the all-zero stateid).
What we rather want to do here is ensure that the delegation is always
correctly marked as needing testing when that is the case. So we want
to close the loophole offered by nfs4_schedule_stateid_recovery(),
which marks the state as needing to be reclaimed, but not the
delegation that may be backing it.
Merge tag 'dmaengine-fix-4.19-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
"Fix the mic_x100_dma driver to use devm_kzalloc for driver memory, so
that it is freed properly when it unregisters from dmaengine using
managed API"
* tag 'dmaengine-fix-4.19-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: mic_x100_dma: use devm_kzalloc to fix an issue
Merge tag 'usb-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for -rc4.
The usual suspects of gadget, xhci, and dwc2/3 are in here, along with
some reverts of reported problem changes, and a number of build
documentation warning fixes. Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
Revert "cdc-acm: implement put_char() and flush_chars()"
usb: Change usb_of_get_companion_dev() place to usb/common
usb: xhci: fix interrupt transfer error happened on MTK platforms
usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()
usb: misc: uss720: Fix two sleep-in-atomic-context bugs
usb: host: u132-hcd: Fix a sleep-in-atomic-context bug in u132_get_frame()
usb: Avoid use-after-free by flushing endpoints early in usb_set_interface()
linux/mod_devicetable.h: fix kernel-doc missing notation for typec_device_id
usb/typec: fix kernel-doc notation warning for typec_match_altmode
usb: Don't die twice if PCI xhci host is not responding in resume
usb: mtu3: fix error of xhci port id when enable U3 dual role
usb: uas: add support for more quirk flags
USB: Add quirk to support DJI CineSSD
usb: typec: fix kernel-doc parameter warning
usb/dwc3/gadget: fix kernel-doc parameter warning
USB: yurex: Check for truncation in yurex_read()
USB: yurex: Fix buffer over-read in yurex_write()
usb: host: xhci-plat: Iterate over parent nodes for finding quirks
xhci: Fix use after free for URB cancellation on a reallocated endpoint
USB: add quirk for WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
...
tcf_sample_act() tried to update its per-cpu stats, but tcf_sample_init()
forgot to allocate them, because tcf_idr_create() was called with a wrong
value of 'cpustats'. Setting it to true proved to fix the reported crash.
Reported-by: Matteo Croce <mcroce@redhat.com> Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Fixes: 5c5670fae430 ("net/sched: Introduce sample tc action") Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'staging-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a few small staging and iio driver fixes for -rc4.
Nothing major, just a few small bugfixes for some reported issues, and
a MAINTAINERS file update for the fbtft drivers.
We also re-enable the building of the erofs filesystem as the XArray
patches that were causing it to break never got merged in the -rc1
cycle, so there's no reason it can't be turned back on for now. The
problem that was previously there is now being handled in the Xarray
tree at the moment, so it will not hit us again in the future.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vboxvideo: Change address of scanout buffer on page-flip
staging: vboxvideo: Fix IRQs no longer working
staging: gasket: TODO: re-implement using UIO
staging/fbtft: Update TODO and mailing lists
staging: erofs: rename superblock flags (MS_xyz -> SB_xyz)
iio: imu: st_lsm6dsx: take into account ts samples in wm configuration
Revert "iio: temperature: maxim_thermocouple: add MAX31856 part"
Revert "staging: erofs: disable compiling temporarile"
MAINTAINERS: Switch a maintainer for drivers/staging/gasket
staging: wilc1000: revert "fix TODO to compile spi and sdio components in single module"
Merge tag 'char-misc-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a small handful of char/misc driver fixes for 4.19-rc4.
All of them are simple, resolving reported problems in a few drivers.
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
firmware: Fix security issue with request_firmware_into_buf()
vmbus: don't return values for uninitalized channels
fpga: dfl: fme: fix return value check in in pr_mgmt_init()
misc: hmc6352: fix potential Spectre v1
Tools: hv: Fix a bug in the key delete code
misc: ibmvsm: Fix wrong assignment of return code
android: binder: fix the race mmap and alloc_new_buf_locked
mei: bus: need to unlink client before freeing
mei: bus: fix hw module get/put balance
mei: fix use-after-free in mei_cl_write
mei: ignore not found client in the enumeration
projects / mirror_ubuntu-kernels.git / log