Masashi Honma [Wed, 30 Nov 2016 00:06:04 +0000 (09:06 +0900)]
mac80211: Suppress NEW_PEER_CANDIDATE event if no room
Previously, kernel sends NEW_PEER_CANDIDATE event to user land even if
the found peer does not have any room to accept other peer. This causes
continuous connection trials.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michael Braun [Tue, 22 Nov 2016 10:52:18 +0000 (11:52 +0100)]
mac80211: multicast to unicast conversion
Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use true/false, rename label to the correct "multicast",
use __be16 for ethertype and network order for constants] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 4a733ef1bea7 (mac80211: remove PM-QoS listener) removed all use
of 'beaconint_us' from ieee80211_recalc_ps() but left the variable
intact. Compiling with W=1 gives the following warning, fix it.
net/mac80211/mlme.c: In function ‘ieee80211_recalc_ps’:
net/mac80211/mlme.c:1481:7: warning: variable ‘beaconint_us’ set but not used [-Wunused-but-set-variable]
iee80211_tu_to_usec has no side-effects and is safe to remove.
Fixes: 4a733ef1bea7 ("mac80211: remove PM-QoS listener") Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: Remove unused 'sband' and 'local' variables
Commit b1bce14a7954 (mac80211: update opmode when adding new station)
refactored ieee80211_vht_handle_opmode into __ieee80211_vht_handle_opmode
and ieee80211_vht_handle_opmode leaving a set but unused variable
(sband) in the former. Compiling with W=1 gives the following warning,
fix it.
net/mac80211/vht.c: In function ‘__ieee80211_vht_handle_opmode’:
net/mac80211/vht.c:424:35: warning: variable ‘sband’ set but not used [-Wunused-but-set-variable]
Remove 'struct ieee80211_local* local' as well, it was only used to
set sband.
This is a harmless warning, and is only being fixed to reduce the
noise with W=1 in the kernel.
Fixes: b1bce14a7954 ("mac80211: update opmode when adding new station") Cc: Marek Kwaczynski <marek.kwaczynski@tieto.com> Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 633e27132625 (mac80211: split sched scan IEs) introduced the
len variable to keep track of the return value of
ieee80211_build_preq_ies() but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/scan.c: In function ‘__ieee80211_request_sched_scan_start’:
net/mac80211/scan.c:1123:9: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
This is a harmless warning and is only being fixed to reduce the noise
with W=1 in the kernel.
Fixes: 633e27132625 ("mac80211: split sched scan IEs") Cc: David Spinadel <david.spinadel@intel.com> Cc: Alexander Bondar <alexander.bondar@intel.com> Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 5bcae31d9 (mac80211: implement multi-vif in-place reservations)
introduced ieee80211_vif_use_reserved_switch() with a counter variable
'i' that is set but not used. Compiling with W=1 gives the following
warning, fix it.
net/mac80211/chan.c: In function ‘ieee80211_vif_use_reserved_switch’:
net/mac80211/chan.c:1273:6: warning: variable ‘i’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise obtained with W=1 in the kernel.
Fixes: 5bcae31d9 ("mac80211: implement multi-vif in-place reservations") Cc: Michal Kazior <michal.kazior@tieto.com> Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3b17fbf87d5d introduced sta_get_expected_throughput()
leaving variable 'struct rate_control_ref* ref' set but unused.
Compiling with W=1 gives the following warning, fix it.
net/mac80211/sta_info.c: In function ‘sta_set_sinfo’:
net/mac80211/sta_info.c:2052:27: warning: variable ‘ref’ set but not used [-Wunused-but-set-variable]
Fixes: 3b17fbf87d5d ("mac80211: mesh: Add support for HW RC implementation") Cc: Johannes Berg <johannes.berg@intel.com> Cc: Maxim Altshul <maxim.altshul@ti.com> Signed-off-by: Kirtika Ruchandani <kirtika@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit f027c2aca0cf introduced 'rates_idx' in
ieee80211_tx_status_noskb but did not use it. Compiling with W=1
gives the following warning, fix it.
mac80211/status.c: In function ‘ieee80211_tx_status_noskb’:
mac80211/status.c:636:6: warning: variable ‘rates_idx’ set but not used [-Wunused-but-set-variable]
This is a harmless warning, and is only being fixed to reduce the
noise generated with W=1.
Fixes: f027c2aca0cf ("mac80211: add ieee80211_tx_status_noskb") Cc: Johannes Berg <johannes.berg@intel.com> Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kirtika Ruchandani <kirtika@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 554891e63a29 introduced 'struct ieee80211_rx_status' in
ieee80211_rx_h_defragment but did not use it. Compiling with W=1
gives the following warning, fix it.
net/mac80211/rx.c: In function ‘ieee80211_rx_h_defragment’:
net/mac80211/rx.c:1911:30: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Fixes: 554891e63a29 ("mac80211: move packet flags into packet") Cc: Johannes Berg <johannes.berg@intel.com> Cc: John W. Linville <linville@tuxdriver.com> Signed-off-by: Kirtika Ruchandani <kirtika@google.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend Van Spriel [Thu, 17 Nov 2016 09:02:40 +0000 (09:02 +0000)]
nl80211: check NL80211_ATTR_SCHED_SCAN_INTERVAL only once
The presence of the NL80211_ATTR_SCHED_SCAN_INTERVAL attribute was
checked in nl80211_parse_sched_scan() and
nl80211_parse_sched_scan_plans() which might be a bit redundant
so removing one.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend Van Spriel [Thu, 17 Nov 2016 12:48:53 +0000 (12:48 +0000)]
cfg80211: get rid of name indirection trick for ieee80211_get_channel()
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Mon, 12 Dec 2016 17:06:38 +0000 (09:06 -0800)]
Merge tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Three patches for minor issues"
* tag 'cris-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: No need to append -O2 and $(LINUXINCLUDE)
tty: serial: make crisv10 explicitly non-modular
cris: Only build flash rescue image if CONFIG_ETRAX_AXISFLASHMAP is selected
Linus Torvalds [Mon, 12 Dec 2016 16:51:37 +0000 (08:51 -0800)]
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull Openrisc updates from Stafford Horne:
- changes to MAINTAINER for openrisc
- probably biggest actual change is the move to memblock from bootmem
- ... plus several bug and build fixes
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: prevent VGA console, fix builds
openrisc: include l.swa in check for write data pagefault
openrisc: Updates after openrisc.net has been lost
openrisc: Consolidate setup to use memblock instead of bootmem
openrisc: remove the redundant of_platform_populate
openrisc: add NR_CPUS Kconfig default value
openrisc: Support both old (or32) and new (or1k) toolchain
openrisc: Add thread-local storage (TLS) support
openrisc: restore all regs on rt_sigreturn
openrisc: fix PTRS_PER_PGD define
Linus Torvalds [Mon, 12 Dec 2016 16:48:28 +0000 (08:48 -0800)]
Merge tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
"Use seq_puts() for fixed strings"
* tag 'm68k-for-v4.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/atari: Use seq_puts() in atari_get_hardware_list()
m68k/amiga: Use seq_puts() in amiga_get_hardware_list()
Linus Torvalds [Mon, 12 Dec 2016 16:46:34 +0000 (08:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: wire up pkey syscalls
AVR32-pio: Replace two seq_printf() calls by seq_puts() in pio_bank_show()
AVR32-pio: Use seq_putc() in pio_bank_show()
AVR32-clock: Combine nine seq_printf() calls into one call in clk_show()
AVR32-clock: Use seq_putc() in two functions
Linus Torvalds [Mon, 12 Dec 2016 16:44:23 +0000 (08:44 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"There are two sets of changes in this pull.
The largest is the addition of the ColdFire platform side i2c support
(the IO addressing, setup and clock definitions). The i2c hardware
module itself is driven by the kernels existing iMX i2c driver.
The other change is the addition of support for the Amcore board"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: AMCORE board, add iMX i2c support
m68k: add Sysam AMCORE open board support
m68knommu: platform support for i2c devices on ColdFire SoC
Pull sparc updates from David Miller:
"Just a bunch of small cleanups and fixes here, and support for user
probes from Allen Pais"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix a building error reported by kbuild
sparc64: fix typo in pgd_clear()
sparc64: restore irq in error paths in iommu
sparc: leon: Fix a retry loop in leon_init_timers()
sparc64: make string buffers large enough
sparc64: move dereference after check for NULL
sparc: kernel: use builtin_platform_driver
sparc64:Support User Probes for sparc
1) Platform regulatory domain support for ath10k, from Bartosz
Markowski.
2) Centralize min/max MTU checking, thus removing tons of duplicated
code all of the the various drivers. From Jarod Wilson.
3) Support ingress actions in act_mirred, from Shmulik Ladkani.
4) Improve device adjacency tracking, from David Ahern.
5) Add support for LED triggers on PHY link state changes, from Zach
Brown.
6) Improve UDP socket memory accounting, from Paolo Abeni.
7) Set SK_MEM_QUANTUM to a fixed size of 4096, instead of PAGE_SIZE.
From Eric Dumazet.
8) Collapse TCP SKBs at retransmit time even if the right side SKB has
frags. Also from Eric Dumazet.
9) Add IP_RECVFRAGSIZE and IPV6_RECVFRAGSIZE cmsgs, from Willem de
Bruijn.
10) Support routing by UID, from Lorenzo Colitti.
11) Handle L3 domain binding (ie. VRF) for RAW sockets, from David
Ahern.
12) tcp_get_info() can run lockless, from Eric Dumazet.
13) 4-tuple UDP hashing in SFC driver, from Edward Cree.
14) Avoid reorders in GRO code, from Eric Dumazet.
15) IPV6 Segment Routing support, from David Lebrun.
16) Support MPLS push and pop for L3 packets in openvswitch, from Jiri
Benc.
17) Add LRU datastructure support for BPF, Martin KaFai Lau.
18) VF support in liquidio driver, from Raghu Vatsavayi.
19) Multiqueue support in alx driver, from Tobias Regnery.
20) Networking cgroup BPF support, from Daniel Mack.
21) TCP chronograph measurements, from Francis Yan.
22) XDP support for qed driver, from Yuval Mintz.
23) BPF based lwtunnels, from Thomas Graf.
24) Consistent FIB dumping to offloading drivers, from Ido Schimmel.
25) Many optimizations for UDP under high load, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
netfilter: nft_counter: rework atomic dump and reset
e1000: use disable_hardirq() for e1000_netpoll()
i40e: don't truncate match_method assignment
net: ethernet: ti: netcp: add support of cpts
net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
net: l2tp: ppp: change PPPOL2TP_MSG_* => L2TP_MSG_*
net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
net: l2tp: export debug flags to UAPI
net: ethernet: stmmac: remove private tx queue lock
net: ethernet: sxgbe: remove private tx queue lock
net: bridge: shorten ageing time on topology change
net: bridge: add helper to set topology change
net: bridge: add helper to offload ageing time
net: nicvf: use new api ethtool_{get|set}_link_ksettings
net: ethernet: ti: cpsw: sync rates for channels in dual emac mode
net: ethernet: ti: cpsw: re-split res only when speed is changed
net: ethernet: ti: cpsw: combine budget and weight split and check
net: ethernet: ti: cpsw: don't start queue twice
net: ethernet: ti: cpsw: use same macros to get active slave
net: mvneta: select GENERIC_ALLOCATOR
...
Randy Dunlap [Sun, 20 Nov 2016 23:40:32 +0000 (08:40 +0900)]
openrisc: prevent VGA console, fix builds
OpenRISC does not support VGA console, so prevent that kconfig symbol
from being enabled for OpenRISC, thus fixing these build errors:
drivers/built-in.o: In function `vgacon_save_screen':
vgacon.c:(.text+0x20e0): undefined reference to `screen_info'
vgacon.c:(.text+0x20e8): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_init':
vgacon.c:(.text+0x284c): undefined reference to `screen_info'
vgacon.c:(.text+0x2850): undefined reference to `screen_info'
drivers/built-in.o: In function `vgacon_startup':
vgacon.c:(.text+0x28d8): undefined reference to `screen_info'
drivers/built-in.o:vgacon.c:(.text+0x28f0): more undefined references to `screen_info' follow
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Chen Gang <gang.chen@asianux.com> Cc: Jonas Bonn <jonas@southpole.se> Signed-off-by: Stafford Horne <shorne@gmail.com>
openrisc: include l.swa in check for write data pagefault
During page fault handling we check the last instruction to understand
if the fault was for a read or for a write. By default we fall back to
read. New instructions were added to the openrisc 1.1 spec for an
atomic load/store pair (l.lwa/l.swa).
This patch adds the opcode for l.swa (0x33) allowing it to be treated as
a write operation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: expanded a bit on the comment] Signed-off-by: Stafford Horne <shorne@gmail.com>
Stafford Horne [Mon, 21 Mar 2016 08:11:10 +0000 (17:11 +0900)]
openrisc: Updates after openrisc.net has been lost
The openrisc.net domain expired and was taken over by squatters.
These updates point documentation to the new domain, mailing lists
and git repos.
Also, Jonas is not the main maintainer anylonger, he reviews changes
but does not maintain a repo or sent pull requests. Updating this to
add Stafford and Stefan who are the active maintainers.
Rob Herring [Tue, 30 Aug 2016 15:10:59 +0000 (00:10 +0900)]
openrisc: remove the redundant of_platform_populate
The of_platform_populate call in the openrisc arch code is now redundant
as the DT core provides a default call. Openrisc has a NULL match table
which means only top level nodes with compatible strings will have
devices creates. The default version will also descend nodes in the
match table such as "simple-bus" which should be fine as openrisc
doesn't have any of these (though it is preferred that memory-mapped
peripherals be grouped under a bus node(s)).
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Stafford Horne <shorne@gmail.com>
openrisc: Support both old (or32) and new (or1k) toolchain
The output file format for or1k has changed from "elf32-or32"
to "elf32-or1k". Select the correct output format automatically
to be able to compile the kernel with both toolchain variants.
Jonas Bonn [Mon, 23 Sep 2013 10:04:20 +0000 (12:04 +0200)]
openrisc: restore all regs on rt_sigreturn
Fix signal handling for when signals are handled as the result of timers
or exceptions, previous code assumed syscalls. This was noticeable with X
crashing where it uses SIGALRM.
This patch restores all regs before returning to userspace via
_resume_userspace instead of via syscall return path.
The rt_sigreturn syscall is more like a context switch than a function
call; it entails a return from one context (the signal handler) to another
(the process in question). For a context switch like this there are
effectively no call-saved regs that remain constant across the transition.
Reported-by: Sebastian Macke <sebastian@macke.de> Signed-off-by: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net>
[shorne@gmail.com: Updated comment better reflect change and issue] Signed-off-by: Stafford Horne <shorne@gmail.com>
On OpenRISC, with its 8k pages, PAGE_SHIFT is defined to be 13.
That makes the expression (1UL << (PAGE_SHIFT-2)) evaluate
to 2048.
The correct value for PTRS_PER_PGD should be 256.
Correcting the PTRS_PER_PGD define unveiled a bug in map_ram(),
where PTRS_PER_PGD was used when the intent was to iterate
over a set of page table entries.
This patch corrects that issue as well.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Acked-by: Jonas Bonn <jonas@southpole.se> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Stafford Horne <shorne@gmail.com>
>> arch/sparc/include/asm/topology_64.h:44:44:
error: implicit declaration of function 'cpu_data'
[-Werror=implicit-function-declaration]
#define topology_physical_package_id(cpu) (cpu_data(cpu).proc_id)
^
Let's include cpudata.h in topology_64.h.
Cc: Sam Ravnborg <sam@ravnborg.org> Cc: David S. Miller <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Gonglei <arei.gonglei@huawei.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 21:15:37 +0000 (00:15 +0300)]
sparc64: restore irq in error paths in iommu
There are some error paths where we should restore IRQs but we don't.
Fixes: bb620c3d3925 ("sparc: Make sparc64 use scalable lib/iommu-common.c functions") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:25:54 +0000 (14:25 +0300)]
sparc: leon: Fix a retry loop in leon_init_timers()
The original code causes a static checker warning because it has a
continue inside a do { } while (0); loop. In that context, a continue
and a break are equivalent. The intent was to go back to the start of
the loop so the continue was a bug.
I've added a retry label at the start and changed the continue to a goto
retry. Then I removed the do { } while (0) loop and pulled the code in
one indent level.
Fixes: 2791c1a43900 ("SPARC/LEON: added support for selecting Timer Core and Timer within core") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:03:55 +0000 (14:03 +0300)]
sparc64: make string buffers large enough
My static checker complains that if "lvl" is ULONG_MAX (this is 64 bit)
then some of the strings will overflow. I don't know if that's possible
but it seems simple enough to make the buffers slightly larger.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 25 Nov 2016 11:01:32 +0000 (14:01 +0300)]
sparc64: move dereference after check for NULL
We shouldn't dereference "iommu" until after we have checked that it is
non-NULL.
Fixes: f08978b0fdbf ("sparc64: Enable sun4v dma ops to use IOMMU v2 APIs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allen Pais [Thu, 13 Oct 2016 04:36:13 +0000 (10:06 +0530)]
sparc64:Support User Probes for sparc
Signed-off-by: Eric Saint Etienne <eric.saint.etienne@oracle.com> Signed-off-by: Allen Pais <allen.pais@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 11 Dec 2016 18:17:39 +0000 (10:17 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Two more MIPS fixes for 4.9:
- RTC: Return -ENODEV so an external RTC will be tried
- Fix mask of GPE frequency
These two have been tested on Imagination's automated test system and
also both received positive reviews on the linux-mips mailing list"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Lantiq: Fix mask of GPE frequency
MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time
Pablo Neira [Sun, 11 Dec 2016 10:43:59 +0000 (11:43 +0100)]
netfilter: nft_counter: rework atomic dump and reset
Dump and reset doesn't work unless cmpxchg64() is used both from packet
and control plane paths. This approach is going to be slow though.
Instead, use a percpu seqcount to fetch counters consistently, then
subtract bytes and packets in case a reset was requested.
The cpu that running over the reset code is guaranteed to own this stats
exclusively, we have to turn counters into signed 64bit though so stats
update on reset don't get wrong on underflow.
This patch is based on original sketch from Eric Dumazet.
Fixes: 43da04a593d8 ("netfilter: nf_tables: atomic dump and reset for stateful objects") Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Luuk Paulussen [Wed, 7 Dec 2016 22:43:34 +0000 (11:43 +1300)]
MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time
The sync_cmos_clock function in kernel/time/ntp.c first tries to update
the internal clock of the cpu by calling the "update_persistent_clock64"
architecture specific function. If this returns -ENODEV, it then tries
to update an external RTC using "rtc_set_ntp_time".
On the mips architecture, the weak implementation of the underlying
function would return 0 if it wasn't overridden. This meant that the
sync_cmos_clock function would never try to update an external RTC
(if both CONFIG_GENERIC_CMOS_UPDATE and CONFIG_RTC_SYSTOHC are
configured)
Returning -ENODEV instead, means that an external RTC will be tried.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz> Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz> Reviewed-by: Scott Parlane <scott.parlane@alliedtelesis.co.nz> Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14649/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WANG Cong [Sat, 10 Dec 2016 22:22:42 +0000 (14:22 -0800)]
e1000: use disable_hardirq() for e1000_netpoll()
In commit 02cea3958664 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.
This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk> Suggested-by: Sabrina Dubroca <sd@queasysnail.net> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Keller, Jacob E [Fri, 9 Dec 2016 21:39:21 +0000 (13:39 -0800)]
i40e: don't truncate match_method assignment
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Bimmy Pujari <bimmy.pujari@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WingMan Kwok [Thu, 8 Dec 2016 22:21:56 +0000 (16:21 -0600)]
net: ethernet: ti: netcp: add support of cpts
This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: WingMan Kwok <w-kwok2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Wed, 7 Dec 2016 19:20:51 +0000 (13:20 -0600)]
net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*
PPPOL2TP_MSG_* and L2TP_MSG_* are duplicates, and are being used
interchangeably in the kernel, so let's standardize on L2TP_MSG_*
internally, and keep PPPOL2TP_MSG_* defined in UAPI for compatibility.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: bridge: fast ageing on topology change
802.1D [1] specifies that the bridges in a network must use a short
value to age out dynamic entries in the Filtering Database for a period,
once a topology change has been communicated by the root bridge.
This patchset fixes this for the in-kernel STP implementation.
Once the topology change flag is set in a net_bridge instance, the
ageing time value is shorten to twice the forward delay used by the
topology.
When the topology change flag is cleared, the ageing time configured for
the bridge is restored.
To accomplish that, a new bridge_ageing_time member is added to the
net_bridge structure, to store the user configured bridge ageing time.
Two helpers are added to offload the ageing time and set the topology
change flag in the net_bridge instance. Then the required logic is added
in the topology change helper if in-kernel STP is used.
When unplugging/replugging the laptop, the slave bridge (under test)
gets the topology change flag sent by the root bridge, and fast ageing
is triggered on the bridges. Once the topology change timer of the root
bridge expires, the topology change flag is cleared and the configured
ageing time is restored on the bridges.
A similar test has been done between two bridges under test.
When changing the forward delay of the root bridge with:
Vivien Didelot [Sat, 10 Dec 2016 18:44:29 +0000 (13:44 -0500)]
net: bridge: shorten ageing time on topology change
802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.
Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).
If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.
Vivien Didelot [Sat, 10 Dec 2016 18:44:27 +0000 (13:44 -0500)]
net: bridge: add helper to offload ageing time
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.
Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:49 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: re-split res only when speed is changed
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Sat, 10 Dec 2016 12:23:48 +0000 (14:23 +0200)]
net: ethernet: ti: cpsw: combine budget and weight split and check
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Sat, 10 Dec 2016 10:38:32 +0000 (11:38 +0100)]
net: mvneta: select GENERIC_ALLOCATOR
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a45 ("net: marvell: Allow drivers to be built with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Limit the number of can filters to avoid > MAX_ORDER allocations.
Fix from Marc Kleine-Budde.
2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
configurations. From Stephen Hemminger.
3) Return proper error when memory allocation fails in
ser_gigaset_init(), from Dan Carpenter.
4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
Feng.
5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
Florian Fainelli.
6) Handle probe deferral properly in smsc911x driver.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: mlx5: Fix Kconfig help text
net: smsc911x: back out silently on probe deferrals
ibmveth: set correct gso_size and gso_type
net: ethernet: cpmac: Call SET_NETDEV_DEV()
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
vhost-vsock: fix orphan connection reset
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
ser_gigaset: return -ENOMEM on error instead of success
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
can: peak: fix bad memory access and free sequence
phy: Don't increment MDIO bus refcount unless it's a different owner
netvsc: reduce maximum GSO size
drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
can: raw: raw_setsockopt: limit number of can_filter that can be set
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet Signed-off-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij [Fri, 9 Dec 2016 13:18:00 +0000 (14:18 +0100)]
net: smsc911x: back out silently on probe deferrals
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:59:05 +0000 (22:59 -0500)]
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 8 Dec 2016 22:40:03 +0000 (16:40 -0600)]
ibmveth: set correct gso_size and gso_type
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com> Reviewed-by: David Dai <zdai@us.ibm.com> Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:57 +0000 (11:41 -0800)]
udp: udp_rmem_release() should touch sk_rmem_alloc later
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:56 +0000 (11:41 -0800)]
udp: add batching to udp_rmem_release()
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 8 Dec 2016 19:41:55 +0000 (11:41 -0800)]
udp: copy skb->truesize in the first cache line
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 10 Dec 2016 03:11:15 +0000 (22:11 -0500)]
Merge branch 'qcom-emac'
Timur Tabi says:
====================
net: qcom/emac: simplify support for different SOCs
On SOCs that have the Qualcomm EMAC network controller, the internal
PHY block is always different. Sometimes the differences are small,
sometimes it might be a completely different IP. Either way, using version
numbers to differentiate them and putting all of the init code in one
file does not scale.
This patchset does two things: The first breaks up the current code into
different files, and the second patch adds support for a third SOC, the
Qualcomm Technologies QDF2400 ARM Server SOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:21 +0000 (13:24 -0600)]
net: qcom/emac: add support for the Qualcomm Technologies QDF2400
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 8 Dec 2016 19:24:20 +0000 (13:24 -0600)]
net: qcom/emac: move phy init code to separate files
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 9 Dec 2016 19:27:22 +0000 (11:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Several fixes to the DSM (ACPI device specific method) marshaling
implementation.
I consider these urgent enough to send for 4.9 consideration since
they fix the kernel's handling of ARS (Address Range Scrub) commands.
Especially for platforms without machine-check-recovery capabilities,
successful execution of ARS commands enables the platform to
potentially break out of an infinite reboot problem if a media error
is present in the boot path. There is also a one line fix for a
device-dax read-only mapping regression.
Commits 9a901f5495e2 ("acpi, nfit: fix extended status translations
for ACPI DSMs") and 325896ffdf90 ("device-dax: fix private mapping
restriction, permit read-only") are true regression fixes for changes
introduced this cycle.
Commit efda1b5d87cb ("acpi, nfit, libnvdimm: fix / harden ars_status
output length handling") fixes the kernel's handling of zero-length
results, this never would have worked in the past, but we only just
recently discovered a BIOS implementation that emits this arguably
spec non-compliant result.
The remaining two commits are additional fall out from thinking
through the implications of a zero / truncated length result of the
ARS Status command.
In order to mitigate the risk that these changes introduce yet more
regressions they are backstopped by a new unit test in commit a7de92dac9f0 ("tools/testing/nvdimm: unit test acpi_nfit_ctl()") that
mocks up inputs to acpi_nfit_ctl()"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix private mapping restriction, permit read-only
tools/testing/nvdimm: unit test acpi_nfit_ctl()
acpi, nfit: fix bus vs dimm confusion in xlat_status
acpi, nfit: validate ars_status output buffer size
acpi, nfit, libnvdimm: fix / harden ars_status output length handling
acpi, nfit: fix extended status translations for ACPI DSMs
Linus Torvalds [Fri, 9 Dec 2016 19:07:45 +0000 (11:07 -0800)]
Merge branch 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"This is quite late but SCT Write Same support added during this cycle
is broken subtly but seriously and it'd be best to disable it before
v4.9 gets released.
This contains two commits - one low impact sata_mv fix and the
mentioned disabling of SCT Write Same"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata-scsi: disable SCT Write Same for the moment
ata: sata_mv: check for errors when parsing nr-ports from dt
Linus Torvalds [Fri, 9 Dec 2016 19:00:39 +0000 (11:00 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Final batch of SoC fixes
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3,
correcting number of SATA ports on a Marvell-based Linkstation
platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
freeze when starting up X"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
ARM: dts: imx7d: fix LCDIF clock assignment
dts: sun8i-h3: correct UART3 pin definitions
Linus Torvalds [Fri, 9 Dec 2016 18:54:54 +0000 (10:54 -0800)]
Merge tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- build fix for drivers calling ndelay() in a conditional block without
curly braces
- defconfig updates
* tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix ndelay() macro
m68k/defconfig: Update defconfigs for v4.9-rc1
Linus Torvalds [Fri, 9 Dec 2016 18:50:49 +0000 (10:50 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fix from Dave Airlie:
"Just a single fix for amdgpu to just suspend the gpu on 'shutdown'
instead of shutting it down fully, as for some reason the hw was
getting upset in some situations"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: just suspend the hw on pci shutdown
It shouldn't have come in yet - it depends on the changes in linux-next
that will come in during the next merge window. As Matthew Wilcox says,
the test suite is broken with the current state without the revert.
Requested-by: Matthew Wilcox <mawilcox@microsoft.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Thu, 8 Dec 2016 16:22:09 +0000 (17:22 +0100)]
cfg80211/mac80211: fix BSS leaks when abandoning assoc attempts
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vamsi Krishna [Fri, 2 Dec 2016 21:59:08 +0000 (23:59 +0200)]
nl80211: Use different attrs for BSSID and random MAC addr in scan req
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit ad2b26abc157 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d39177 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d39177 ("cfg80211: Allow a scan request for a specific BSSID") Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com> Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes: e3978673f514 ("drivers: net: xgene: Fix MSS programming") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-focal-kernel.git / log