Johan Hedberg [Sun, 20 Jan 2013 12:27:20 +0000 (14:27 +0200)]
Bluetooth: Fix checking for valid disconnect parameters in unpair_device
The valid values for the Disconnect parameter in the Unpair Device
command are 0x00 and 0x01. If any other value is encountered the command
should fail with the appropriate invalid params response.
Johan Hedberg [Sun, 20 Jan 2013 12:27:19 +0000 (14:27 +0200)]
Bluetooth: Fix checking for valid address type values in mgmt commands
This patch adds checks for valid address type values passed to mgmt
commands. If an invalid address type is encountered the code will return
a proper invalid params response.
Johan Hedberg [Sun, 20 Jan 2013 12:27:18 +0000 (14:27 +0200)]
Bluetooth: Add helper functions for testing bdaddr types
This patch adds two helper functions to test for valid bdaddr type
values. These will be particularely useful in the mgmt code to check
that user space has passed valid values to the kernel.
Johan Hedberg [Sun, 20 Jan 2013 12:27:17 +0000 (14:27 +0200)]
Bluetooth: Check for valid key->authenticated value for LTKs
This patch adds necessary checks for the two allowed values of the
authenticated parameter of each Long Term Key, i.e. 0x00 and 0x01. If
any other value is encountered the valid response is to return invalid
params to user space.
Johan Hedberg [Sun, 20 Jan 2013 12:27:16 +0000 (14:27 +0200)]
Bluetooth: Refactor valid LTK data testing into its own function
This patch refactors valid LTK data testing into its own function. This
will help keep the code readable since there are several tests still
missing that need to be done on the LTK data.
Johan Hedberg [Sun, 20 Jan 2013 12:27:15 +0000 (14:27 +0200)]
Bluetooth: Fix checking for proper key->master value in Load LTKs
The allowed values for the key->master parameter in the Load LTKs
command are 0x00 and 0x01. If there is a key in the list with some other
value the command should fail with a proper invalid params response.
Johan Hedberg [Sun, 20 Jan 2013 12:27:14 +0000 (14:27 +0200)]
Bluetooth: Fix returning proper mgmt status for Load LTKs
Failures of mgmt commands should be indicated with valid mgmt status
codes, and EINVAL is not one of them. Instead MGMT_STATUS_INVALID_PARAMS
should be returned.
Johan Hedberg [Sun, 20 Jan 2013 12:27:13 +0000 (14:27 +0200)]
Bluetooth: Fix checking for correct mgmt_load_link_keys parameters
The debug_keys parameter is only allowed to have the values 0x00 and
0x01. Any other value should result in a proper command status with
MGMT_STATUS_INVALID_PARAMS.
Szymon Janc [Fri, 18 Jan 2013 11:48:07 +0000 (12:48 +0100)]
Bluetooth: Fix pair device command reply if adapter is powered off
According to Bluetooth Management API specification Pair Device Command
should generate command complete event on both success and failure.
This fix replying with command status (which lacks address info) when
adapter is powered off.
Johan Hedberg [Wed, 16 Jan 2013 14:15:34 +0000 (16:15 +0200)]
Bluetooth: Fix Class of Device indication when powering off
When a HCI device is powered off the Management interface specification
dictates that the class of device value is indicated as zero. This patch
fixes sending of the appropriate class of device changed event when a
HCI device is powered off.
Johan Hedberg [Mon, 14 Jan 2013 20:33:52 +0000 (22:33 +0200)]
Bluetooth: Fix using system-global workqueue when not necessary
There's a per-HCI device workqueue (hdev->workqueue) that should be used
for general per-HCI device work (except hdev->req_workqueue that's for
hci_request() related work). This patch fixes places using the
system-global work queue and makes them use the hdev->workqueue instead.
Johan Hedberg [Mon, 14 Jan 2013 20:33:51 +0000 (22:33 +0200)]
Bluetooth: Use req_workqueue for hci_request operations
This patch converts work assignment relying on hci_request() from the
system-global work queue to the per-HCI device specific work queue
(hdev->req_workqueue) intended for hci_request() related tasks.
Johan Hedberg [Mon, 14 Jan 2013 20:33:50 +0000 (22:33 +0200)]
Bluetooth: Add a new workqueue for hci_request operations
The hci_request function is blocking and cannot be called through the
usual per-HCI device workqueue (hdev->workqueue). While hci_request is
in progress any other work from the queue, including sending HCI
commands to the controller would be blocked and eventually cause the
hci_request call to time out.
This patch adds a second workqueue to be used by operations needing
hci_request and thereby avoiding issues with blocking other workqueue
users.
Johan Hedberg [Wed, 9 Jan 2013 13:29:40 +0000 (15:29 +0200)]
Bluetooth: Fix sending incorrect new_settings for mgmt_set_powered
The socket from which a mgmt_set_powered command was received should
only receive the command response but no new_settings event.
The mgmt_powered() function which is used to handle the situation with
the HCI_AUTO_OFF flag tries to check for a pending command to know which
socket to skip the event for, but since the pending command hasn't been
added this will not happen.
This patch fixes the issue by adding the pending command for the
HCI_AUTO_OFF case and thereby ensures that mgmt_powered() will skip the
right socket when sending the new_settings event, but still send the
proper response to the socket where the command came from.
Johan Hedberg [Thu, 10 Jan 2013 12:54:09 +0000 (14:54 +0200)]
Bluetooth: Fix returning proper command status for start_discovery
Management commands should whenever possible fail with proper command
status or command complete events. This patch fixes the
mgmt_start_discovery command to do this for the failure cases where an
incorrect parameter value was passed to it ("not supported" if the
parameter value was valid but the controller doesn't support it and
"invalid params" if it isn't valid at all).
Johan Hedberg [Wed, 9 Jan 2013 14:05:19 +0000 (16:05 +0200)]
Bluetooth: Fix checking for exact values of boolean mgmt parameters
All mgmt_set_* commands that take a boolean value encoded in the form of
a byte should only accept the values 0x00 and 0x01. This patch adds the
necessary checks for this and returns "invalid params" responses if
anything else is provided as the value.
Johan Hedberg [Wed, 9 Jan 2013 13:29:38 +0000 (15:29 +0200)]
Bluetooth: Move non-critical sections outside of the dev lock
This patch fixes sections of code that do not need hci_lock_dev to be
outside of the lock. Such sections include code that do not touch the
hdev at all as well as sections which just read a single byte from the
supported_features value (i.e. all lmp_*_capable() macros).
Johan Hedberg [Wed, 9 Jan 2013 13:29:36 +0000 (15:29 +0200)]
Bluetooth: Fix accepting set_dev_class for non-BR/EDR controllers
The concept of Class of Device only exists for BR/EDR controllers. The
mgmt_set_dev_class command should therefore return a proper "not
supported" error if it is attempted for a controller that doesn't
support BR/EDR (e.g. a single mode LE-only one).
Johan Hedberg [Wed, 9 Jan 2013 13:29:35 +0000 (15:29 +0200)]
Bluetooth: Fix checking for valid device class values
The two lowest bits of the minor device class value are reserved and
should be zero, and the three highest bits of the major device class
likewise. The management code should therefore test for this and return
a proper "invalid params" error if the condition is not met.
Johan Hedberg [Wed, 9 Jan 2013 13:29:34 +0000 (15:29 +0200)]
Bluetooth: Fix missing command complete for mgmt_load_long_term_keys
All management events are expected to indicate successful completion
through a command complete event, however the load long term keys
command was missing this. This patch adds the missing event.
Johan Hedberg [Wed, 9 Jan 2013 13:29:33 +0000 (15:29 +0200)]
Bluetooth: Fix missing command complete event for mgmt_confirm_name
All management commands are expected to indicate successful completion
through a command complete event however the confirm name command was
missing it. This patch add the sending of the missing event.
Szymon Janc [Thu, 13 Dec 2012 14:11:20 +0000 (15:11 +0100)]
Bluetooth: mgmt: Remove not needed restriction on add/remove OOB data
Those commands don't send any HCI commands to controller so there is no
need to restrict them to only powered up controller. This also makes
implementation more consistent as already stored remote OOB data
persist power toggle.
Remove code which cannot execute. l2cap_conn_add for AMP_LINK
might only be invoked when receiving data in l2cap_recv_acldata.
But this case is checked in the first statement there.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Avinash Patil [Fri, 4 Jan 2013 05:21:32 +0000 (21:21 -0800)]
mwifiex: use map/unmap APIs in TX and RX to reduce memcpy
This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Fri, 4 Jan 2013 05:21:30 +0000 (21:21 -0800)]
mwifiex: use pci_alloc/free_consistent APIs for PCIe
This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Fri, 4 Jan 2013 05:21:29 +0000 (21:21 -0800)]
mwifiex: add init_fw_port handler for PCIe interface
This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Fri, 4 Jan 2013 05:21:28 +0000 (21:21 -0800)]
mwifiex: access interrupt status only while holding lock
This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.
Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 3 Jan 2013 23:51:21 +0000 (00:51 +0100)]
bcma: mips: explicit assign IRQ numbers
The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Handle watchdog event with highest prioriry
Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.
This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.
Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Handle Watchdog events for the new ampdu streams
With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.
Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: Enable support to support additional ampdu streams
Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Enable calibration types in init_cal_settings
Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex: use correct htcapinfo for HT20 ibss network
It is observed that same htcapinfo ie is included in beacon for
HT20, HT40+ and HT40- ibss networks. This patch makes sure that
we will not advertise 40Mhz flags while creating/joining ibss
network in HT20 mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54pci: don't return zero on failure paths in p54p_probe()
If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(),
it breaks off initialization, deallocates all resources, but returns zero.
Similar issue is if check for returned value of pci_resource_len() fails.
The patch implements proper error code propagation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 2 Jan 2013 14:22:49 +0000 (15:22 +0100)]
brcmfmac: Return correct error on netdev xmit.
Netdev xmit routine brcfm_netdev_start_xmit was defined
incorrectly and used wrong return codes. Always eat the
packet and return ok. Remove drvr_up check since it is not
relevant.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The header of the ethernet packet is processed conditionally, but
the check is wrong as it checks skb length is at least ETH_ALEN. It
should check it is at least sizeof struct ethhdr instead.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver had some global definitions in dhd.h to map event
identifiers to event names. With redesign of firmware event
processing this has all moved to fweh module so these definitions
can be removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 2 Jan 2013 14:22:44 +0000 (15:22 +0100)]
brcmfmac: Use dedicated trace level for CDC.
CDC debug is partly done with TRACE and partly with CTL, however
CDC hardly ever needs debugging. Use dedicated level CDC and
replace TRACE and CTL in dhd_cdc with that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: remove rx helper function from bus interface
The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.
Cc: Joe Perches <joe@perches.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: assure USB dongle firmware is reset upon module unload
Upon unloading the brcmfmac module the USB firmware should be reset
as the device remains powered. The reset assures a known device
state when a new brcmfmac driver load is being done.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Wed, 2 Jan 2013 14:22:37 +0000 (15:22 +0100)]
brcmsmac: remove dead code
Dead code after AMPDU restructure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac: allow user-space setting of interface address
The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac: use perimeter lock in add_interface() callback
All callbacks that access driver functions should do that under
perimeter lock protection. The add_interface() callback was lacking
this lock.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piotr Haber [Wed, 2 Jan 2013 14:22:34 +0000 (15:22 +0100)]
brcmsmac: increase timer reference count for new timers only
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 29 Dec 2012 13:51:51 +0000 (14:51 +0100)]
rt2x00: rt2800: convert read_eeprom functions to return an int value
Both the rtt2x00usb_eeprom_read and the ioremap
functions are allowed to fail, however their
return values are not checked in the read_eeprom
functions in the rt2800{pci,usb} drivers.
The patch adds the missing checks, and converts
all read_eeprom functions to return an int value,
so the error values can be propagated up to the
'rt2800_validate_eeprom' function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac: initialize morepending in brcms_b_recv()
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save support was removed from iwlegacy due to possible firmware
crashes problems it cause. I use to plan first inspect code to find
reason of problems, fix them and then allow to enable PS. But
realistically - code inspection will not happen, so let's do it, and
wait for eventual bug reports.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 17 Dec 2012 21:06:08 +0000 (22:06 +0100)]
ath9k: fix column header comments for some initval arrays
Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.
The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the driver supports HW offload in a single
P2P client configuration, it doesn't support HW
offload in the concurrent P2P GO+CLIENT
configuration.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: Only specify interface combinations if more than one interface is possible
Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c
/* Combinations with just one interface aren't real */
if (WARN_ON(c->max_interfaces < 2))
Note: The number of supported interfaces is set by
the carl9170 firmware. The default number of
supported interfaces for all current firmwares is 2.
Therefore this warning can only be observed with
custom firmwares.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: allow P2P_GO interface creation after P2P_CLIENT
Janusz Dziedzic reported that after a change in wpa_supplicant
["nl80211: Automatically use concurrent P2P if possible"],
carl9170 was no longer able to host a P2P network.
This patch tackles the problem by allowing GO interfaces to be
registered, long after the P2P_CLIENT interface is brought up.
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test [ath9k and carl9170],
TDLS seemed to be working fine. And while
we are at it, let's move the wiphy feature
flag set from carl9170_alloc into a single
place in carl9170_fw.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 12 Dec 2012 12:14:23 +0000 (13:14 +0100)]
ath9k_hw: use the devres API for allocations
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 12 Dec 2012 12:14:22 +0000 (13:14 +0100)]
ath9k: use the devres API for allocations/mappings
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_init_rfcsr() is too big, split RF initialization into per chip
functions. Code will change, but we should setup the same values onto
RF registers and in the same order as before.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 27 Dec 2012 21:58:21 +0000 (22:58 +0100)]
iwlwifi: move some PCIe calls to better places
Synchronizing the IRQ is pointless when we will
then enable the RF-Kill interrupt again, but is
needed before we free it and the data needed to
handle IRQs; move it to the free function.
Simiarly, cancelling the replenish work struct
can move to the function that frees the RX data
structures.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_grab_nic_access returns a boolean. So ret should
explicitely set to an error code and not rely on the value
returned by iwl_trans_grab_nic_access.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / mirror_ubuntu-disco-kernel.git / log