This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fast switching path only emits an event for the CPU of interest, whereas the
regular path emits an event for all the CPUs that had their frequency changed,
i.e. all the CPUs sharing the same policy.
With the current behavior, looking at cpu_frequency event for a given CPU that
is using the fast switching path will not give the correct frequency signal.
Signed-off-by: Douglas RAILLARD <douglas.raillard@arm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to the ACPI 6.3 specification, the _PSD method is optional
when using CPPC. The underlying assumption is that each CPU can change
frequency independently from all other CPUs; _PSD is provided to tell
the OS that some processors can NOT do that.
However, the acpi_get_psd() function returns ENODEV if there is no _PSD
method present, or an ACPI error status if an error occurs when evaluating
_PSD, if present. This makes _PSD mandatory when using CPPC, in violation
of the specification, and only on Linux.
This has forced some firmware writers to provide a dummy _PSD, even though
it is irrelevant, but only because Linux requires it; other OSPMs follow
the spec. We really do not want to have OS specific ACPI tables, though.
So, correct acpi_get_psd() so that it does not return an error if there
is no _PSD method present, but does return a failure when the method can
not be executed properly. This allows _PSD to be optional as it should
be.
Signed-off-by: Al Stone <ahs3@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> Reviewed-by: Daniel Drake <drake@endlessm.com> Link: https://lore.kernel.org/r/20190826153900.25969-1-katsuhiro@katsuster.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fixed misspelled words, added error check during probe
on the init of the registers, and fixed ALS/I2C control
mode.
Fixes: bc1b8492c764 ("leds: lm3532: Introduce the lm3532 LED driver") Reported-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour
Prevent mangling with gains with invalid values.
As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While this might not occur in practice, if the device is doing
the right thing, it would be teoretically be possible to have
both hsync_counter and vsync_counter negatives.
If this ever happen, ctrl will be undefined, but the driver
will still call:
Reviewed-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In case memory resources for *buf* and *paths* were allocated, jump to
*out* and release them before return.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Gustavo A. R. Silva <gustavo@embeddedor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org>
Addresses-Coverity-ID: 1444328 ("Resource leak") Fixes: 6f3da20e151f ("perf report: Support builtin perf script in scripts menu") Link: http://lkml.kernel.org/r/20190408162748.GA21008@embeddedor Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While tracing a program that calls isatty(3), I noticed that strace
reported TCGETS for the request argument of the underlying ioctl(2)
syscall while perf trace reported TCSETS. strace is corrrect. The bug in
perf was due to the tty ioctl beauty table starting at 0x5400 rather
than 0x5401.
Committer testing:
Using augmented_raw_syscalls.o and settings to make 'perf trace'
use strace formatting, i.e. with this in ~/.perfconfig
# cat ~/.perfconfig
[trace]
add_events = /home/acme/git/linux/tools/perf/examples/bpf/augmented_raw_syscalls.c
show_zeros = yes
show_duration = no
no_inherit = yes
show_timestamp = no
show_arg_names = no
args_alignment = 40
show_prefix = yes
In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.
So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.
Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.
Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.
Fixes: 996133119f57 ("PM / devfreq: Add new passive governor") Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
<generated/ti-pm-asm-offsets.h> is only generated and included by
arch/arm/mach-omap2/, so it does not need to reside in the globally
visible include/generated/.
I renamed it to arch/arm/mach-omap2/pm-asm-offsets.h since the prefix
'ti-' is just redundant in mach-omap2/.
My main motivation of this change is to avoid the race condition for
the parallel build (-j) when CONFIG_IKHEADERS is enabled.
When it is enabled, all the headers under include/ are archived into
kernel/kheaders_data.tar.xz and exposed in the sysfs.
In the parallel build, we have no idea in which order files are built.
- If ti-pm-asm-offsets.h is built before kheaders_data.tar.xz,
the header will be included in the archive. Probably nobody will
use it, but it is harmless except that it will increase the archive
size needlessly.
- If kheaders_data.tar.xz is built before ti-pm-asm-offsets.h,
the header will not be included in the archive. However, in the next
build, the archive will be re-generated to include the newly-found
ti-pm-asm-offsets.h. This is not nice from the build system point
of view.
- If ti-pm-asm-offsets.h and kheaders_data.tar.xz are built at the
same time, the corrupted header might be included in the archive,
which does not look nice either.
This commit fixes the race.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes: b53b0128052ff ("PM / devfreq: Fix static checker warning in try_then_request_governor") Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ARM Erratum 754322 affects Cortex-A9 revisions r2p* and r3p*.
Automatically enable support code to mitigate the erratum when compiling
a kernel for any of the affected Renesas SoCs:
- RZ/A1: r3p0,
- R-Mobile A1: r2p4,
- R-Car M1A: r2p2-00rel0,
- R-Car H1: r3p0,
- SH-Mobile AG5: r2p2.
EMMA Mobile EV2 (r1p3) and RZ/A2 (r4p1) are not affected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the R-Mobile "always-on" PM Domain is implemented by returning
-EBUSY from the generic_pm_domain.power_off() callback, and doing
nothing in the generic_pm_domain.power_on() callback. However, this
means the PM Domain core code is not aware of the semantics of this
special domain, leading to boot warnings like the following on
SH/R-Mobile SoCs:
sh_cmt e6130000.timer: PM domain c5 will not be powered off
Fix this by making the always-on nature of the domain explicit instead,
by setting the GENPD_FLAG_ALWAYS_ON flag. This removes the need for the
domain to provide power control callbacks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
<generated/at91_pm_data-offsets.h> is only generated and included by
arch/arm/mach-at91/, so it does not need to reside in the globally
visible include/generated/.
I renamed it to arch/arm/mach-at91/pm_data-offsets.h since the prefix
'at91_' is just redundant in mach-at91/.
My main motivation of this change is to avoid the race condition for
the parallel build (-j) when CONFIG_IKHEADERS is enabled.
When it is enabled, all the headers under include/ are archived into
kernel/kheaders_data.tar.xz and exposed in the sysfs.
In the parallel build, we have no idea in which order files are built.
- If at91_pm_data-offsets.h is built before kheaders_data.tar.xz,
the header will be included in the archive. Probably nobody will
use it, but it is harmless except that it will increase the archive
size needlessly.
- If kheaders_data.tar.xz is built before at91_pm_data-offsets.h,
the header will not be included in the archive. However, in the next
build, the archive will be re-generated to include the newly-found
at91_pm_data-offsets.h. This is not nice from the build system point
of view.
- If at91_pm_data-offsets.h and kheaders_data.tar.xz are built at the
same time, the corrupted header might be included in the archive,
which does not look nice either.
This commit fixes the race.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Link: https://lore.kernel.org/r/20190823024346.591-1-yamada.masahiro@socionext.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
AMD Family 17h systems currently require address translation in order to
report the system address of a DRAM ECC error. This is currently done
before decoding the syndrome information. The syndrome information does
not depend on the address translation, so the proper EDAC csrow/channel
reporting can function without the address. However, the syndrome
information will not be decoded if the address translation fails.
Decode the syndrome information before doing the address translation.
The syndrome information is architecturally defined in MCA_SYND and can
be considered robust. The address translation is system-specific and may
fail on newer systems without proper updates to the translation
algorithm.
Fixes: 713ad54675fd ("EDAC, amd64: Define and register UMC error decode function") Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org> Cc: James Morse <james.morse@arm.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Tony Luck <tony.luck@intel.com> Link: https://lkml.kernel.org/r/20190821235938.118710-6-Yazen.Ghannam@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Following the patch 'perf stat: Fix --no-scale', an alignment trap
happens in process_counter_values() on ARMv7 platforms due to the
attempt to copy non 64 bits aligned double words (pointed by 'count')
via a NEON vectored instruction ('vld1' with 64 bits alignment
constraint).
This patch sets a 64 bits alignment constraint on 'contents[]' field in
'struct xyarray' since the 'count' pointer used above points to such a
structure.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1566464769-16374-1-git-send-email-gerald.baeza@st.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The struct chip_select array that's used for saving chip select bases
and masks is fixed at length of two. There should be one struct
chip_select for each controller, so this array should be increased to
support systems that may have more than two controllers.
Increase the size of the struct chip_select array to eight, which is the
largest number of controllers per die currently supported on AMD
systems.
Fix number of DIMMs and Chip Select bases/masks on Family17h, because
AMD Family 17h systems support 2 DIMMs, 4 CS bases, and 2 CS masks per
channel.
Also, carve out the Family 17h+ reading of the bases/masks into a
separate function. This effectively reverts the original bases/masks
reading code to before Family 17h support was added.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org> Cc: James Morse <james.morse@arm.com> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Tony Luck <tony.luck@intel.com> Link: https://lkml.kernel.org/r/20190821235938.118710-2-Yazen.Ghannam@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Warning when p == NULL and then proceeding and dereferencing p does not
make any sense as the kernel will crash with a NULL pointer dereference
right away.
Bailing out when p == NULL and returning an error code does not cure the
underlying problem which caused p to be NULL. Though it might allow to
do proper debugging.
Same applies to the clock id check in set_process_cpu_timer().
Clean them up and make them return without trying to do further damage.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Link: https://lkml.kernel.org/r/20190819143801.846497772@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
KASAN: global-out-of-bounds Read in dvb_pll_attach
Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).
Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12
The buggy address belongs to the variable:
id+0x100/0x120
Memory state around the buggy address: ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00 ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
^ ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================
Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix and eliminate mceusb's IR length limit for IR signals transmitted to
the MCE IR blaster ports.
An IR signal TX exceeding 306 pulse/space samples presently causes -EINVAL
return error. There's no such limitation nor error with the MCE device
hardware. And valid IR signals exist with more than 400 pulse/space for the
control of certain appliances (eg Panasonic ACXA75C00600 air conditioner).
The scope of this patch is limited to the mceusb driver. There are still
IR signal TX length and time constraints that related modules of rc core
(eg LIRC) impose, further up the driver stack.
Changes for mceusb_tx_ir():
Converts and sends LIRC IR pulse/space sequence to MCE device IR
pulse/space format.
Break long length LIRC sequence into multiple (unlimited number of) parts
for sending to the MCE device.
Reduce kernel stack IR buffer size: 128 (was 384)
Increase MCE IR data packet size: 31 (was 5)
Zero time LIRC pulse/space no longer copied to MCE IR data.
Eliminate overwriting the source/input LIRC IR data in txbuf[].
Eliminate -EINVAL return; return number of IR samples sent (>0) or
MCE write error code (<0).
New mce_write() and mce_write_callback():
Implements synchronous blocking I/O, with timeout, for writing/sending
data to the MCE device.
An unlimited multipart IR signal sent to the MCE device faster than real
time requires flow control absent with the original mce_request_packet()
and mce_async_callback() asynchronous I/O implementation. Also absent is
TX error feedback.
mce_write() combines and replaces mce_request_packet() and
mce_async_callback() with conversion to synchronous I/O.
mce_write() returns bytes sent (>0) or MCE device write error (<0).
Debug hex dump TX data before processing.
Rename mce_async_out() -> mce_command_out():
The original name is misleading with underlying synchronous I/O
implementation. Function renamed to mce_command_out().
Changes in mceusb_handle_command():
Add support for MCE device error case MCE_RSP_TX_TIMEOUT
"IR TX timeout (TX buffer underrun)"
Changes in mceusb_dev_printdata():
Changes support test and debug of multipart TX IR.
Add buffer boundary information (offset and buffer size) to TX hex dump.
Correct TX trace bug "Raw IR data, 0 pulse/space samples"
Add trace for MCE_RSP_TX_TIMEOUT "IR TX timeout (TX buffer underrun)"
Other changes:
The driver's write to USB device architecture change (async to sync I/O)
is significant so we bump DRIVER_VERSION to "1.95" (from "1.94").
Hex dumps limited to 64 bytes.
0x81 is MCE minimum time pulse, 0x01 is MCE minimum time space.
TX IR part 3 sz=11 shows 20msec I/O blocking delay
(100expire - 98wait = 2jiffies)
Signed-off-by: A Sun <as1033x@comcast.net> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
s390 kasan code uses sclp_early_printk to report initialization
failures. The code doing that should not be instrumented, because kasan
shadow memory has not been set up yet. Even though sclp_early_core.c is
compiled with instrumentation disabled it uses strlen function, which
is instrumented and would produce shadow memory access if used. To
avoid that, introduce uninstrumented __strlen function to be used
instead.
Before commit 7e0d92f00246 ("s390/kasan: improve string/memory functions
checks") few string functions (including strlen) were escaping kasan
instrumentation due to usage of platform specific versions which are
implemented in inline assembly.
Fixes: 7e0d92f00246 ("s390/kasan: improve string/memory functions checks") Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When taking an SError or Debug exception from EL0, we run the C
handler for these exceptions before updating the context tracking
code and unmasking lower priority interrupts.
When booting with nohz_full lockdep tells us we got this wrong:
| =============================
| WARNING: suspicious RCU usage
| 5.3.0-rc2-00010-gb4b5e9dcb11b-dirty #11271 Not tainted
| -----------------------------
| include/linux/rcupdate.h:643 rcu_read_unlock() used illegally wh!
|
| other info that might help us debug this:
|
|
| RCU used illegally from idle CPU!
| rcu_scheduler_active = 2, debug_locks = 1
| RCU used illegally from extended quiescent state!
| 1 lock held by a.out/432:
| #0: 00000000c7a79515 (rcu_read_lock){....}, at: brk_handler+0x00
|
| stack backtrace:
| CPU: 1 PID: 432 Comm: a.out Not tainted 5.3.0-rc2-00010-gb4b5e9d1
| Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno De8
| Call trace:
| dump_backtrace+0x0/0x140
| show_stack+0x14/0x20
| dump_stack+0xbc/0x104
| lockdep_rcu_suspicious+0xf8/0x108
| brk_handler+0x164/0x1b0
| do_debug_exception+0x11c/0x278
| el0_dbg+0x14/0x20
Moving the ct_user_exit calls to be before do_debug_exception() means
they are also before trace_hardirqs_off() has been updated. Add a new
ct_user_exit_irqoff macro to avoid the context-tracking code using
irqsave/restore before we've updated trace_hardirqs_off(). To be
consistent, do this everywhere.
The C helper is called enter_from_user_mode() to match x86 in the hope
we can merge them into kernel/context_tracking.c later.
Cc: Masami Hiramatsu <mhiramat@kernel.org> Fixes: 6c81fe7925cc4c42 ("arm64: enable context tracking") Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
where if the timeout handler runs when the completion path is and we fail
to grab the mutex in the timeout handler we will leave a config reference
and cannot free the config later.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If hw_free() gets called after hw_params(), GCLK remains prepared,
preventing further use of it. This patch fixes this by unpreparing the
clock in hw_free() or if hw_params() gets an error.
Fixes: 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller") Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20190820162411.24836-2-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In led_trigger_set(), 'event' is allocated in kasprintf(). However, it is
not deallocated in the following execution if the label 'err_activate' or
'err_add_groups' is entered, leading to memory leaks. To fix this issue,
free 'event' before returning the error.
Fixes: 52c47742f79d ("leds: triggers: send uevent when changing triggers") Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since hw_free() can be called multiple times and not just after a stop
trigger command, we should check whether the RX or TX ready interrupt was
truly enabled previously. For this, we assure that the condition of the
wait event is always true, except when RX/TX interrupts are enabled.
Fixes: 7e0cdf545a55 ("ASoC: mchp-i2s-mcc: add driver for I2SC Multi-Channel Controller") Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20190820162411.24836-3-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The BCLK divider should be calculated using the parameters that actually
make the BCLK rate: the number of channels, the sampling rate and the
sample width.
We've been using the oversample_rate previously because in the former SoCs,
the BCLK's parent is MCLK, which in turn is being used to generate the
oversample rate, so we end up with something like this:
So, bclk_div = mclk_rate / sampling_rate / word_size / channels.
And this is actually better, since the oversampling ratio only plays a role
because the MCLK is its parent, not because of what BCLK is supposed to be.
Furthermore, that assumption of MCLK being the parent has been broken on
newer SoCs, so let's use the proper formula, and have the parent rate as an
argument.
Fixes: 7d2993811a1e ("ASoC: sun4i-i2s: Add support for H3") Fixes: 21faaea1343f ("ASoC: sun4i-i2s: Add support for A83T") Fixes: 66ecce332538 ("ASoC: sun4i-i2s: Add compatibility with A64 codec I2S") Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://lore.kernel.org/r/c3595e3a9788c2ef2dcc30aa3c8c4953bb5cc249.1566242458.git-series.maxime.ripard@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Found while fixing some other problem, before it was escaping the
tools/ chroot and using stuff in the kernel sources:
CC /tmp/build/perf/util/find_bit.o
In file included from /git/linux/tools/include/../../arch/x86/include/uapi/asm/bitsperlong.h:11,
from /git/linux/tools/include/uapi/asm/bitsperlong.h:3,
from /git/linux/tools/include/linux/bits.h:6,
from /git/linux/tools/include/linux/bitops.h:13,
from ../lib/find_bit.c:17:
# cd /git/linux/tools/include/../../arch/x86/include/uapi/asm/
# pwd
/git/linux/arch/x86/include/uapi/asm
#
Now it is getting the one we want it to, i.e. the one inside tools/:
CC /tmp/build/perf/util/find_bit.o
In file included from /git/linux/tools/arch/x86/include/uapi/asm/bitsperlong.h:11,
from /git/linux/tools/include/linux/bits.h:6,
from /git/linux/tools/include/linux/bitops.h:13,
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-8f8cfqywmf6jk8a3ucr0ixhu@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Back in 2004 we added logic to arch/ppc64/Makefile to pass
the --synthetic option to nm, if it was supported by nm.
Then in 2005 when arch/ppc64 and arch/ppc were merged, the logic to
add --synthetic was moved inside an #ifdef CONFIG_PPC64 block within
arch/powerpc/Makefile, and has remained there since.
That was fine, though crufty, until recently when a change to
init/Kconfig added a config time check that uses $(NM). On powerpc
that leads to an infinite loop because Kconfig uses $(NM) to calculate
some values, then the powerpc Makefile changes $(NM), which Kconfig
notices and restarts.
The original commit that added --synthetic simply said:
On new toolchains we need to use nm --synthetic or we miss code
symbols.
And the nm man page says that the --synthetic option causes nm to:
Include synthetic symbols in the output. These are special symbols
created by the linker for various purposes.
So it seems safe to always pass --synthetic if nm supports it, ie. on
32-bit and 64-bit, it just means 32-bit kernels might have more
symbols reported (and in practice I see no extra symbols). Making it
unconditional avoids the #ifdef CONFIG_PPC64, which in turn avoids the
infinite loop.
Debugged-by: Peter Collingbourne <pcc@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When transitioning to supend state, uniphier_aio_dai_suspend() is called
and asserts reset lines and disables clocks.
However, if there are two or more DAIs, uniphier_aio_dai_suspend() are
called multiple times, and double reset assersion will cause.
This patch defines the counter that has the number of DAIs at first, and
whenever uniphier_aio_dai_suspend() are called, it decrements the
counter. And only if the counter is zero, it asserts reset lines and
disables clocks.
In the same way, uniphier_aio_dai_resume() are called, it increments the
counter after deasserting reset lines and enabling clocks.
Fixes: 139a34200233 ("ASoC: uniphier: add support for UniPhier AIO CPU DAI driver") Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1566281764-14059-1-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In practice can never happen because only the first caller which
increments iosf_mbi_block_punit_i2c_access_count will also take
iosf_mbi_punit_mutex, that is the whole purpose of the counter, which
itself is protected by iosf_mbi_block_punit_i2c_access_count_mutex.
But there is no way to tell the lockdep code about this and we really
want to be able to run a kernel with lockdep enabled without these
warnings being triggered.
2. The lockdep warning also points out another real problem, if 2 threads
both are in a block of code protected by iosf_mbi_block_punit_i2c_access
and the first thread to acquire the block exits before the second thread
then the second thread will call mutex_unlock on iosf_mbi_punit_mutex,
but it is not the thread which took the mutex and unlocking by another
thread is not allowed.
Fix this by getting rid of the notion of holding a mutex for the entire
duration of the PMIC accesses, be it either from the PUnit side, or from an
in kernel I2C driver. In general holding a mutex after exiting a function
is a bad idea and the above problems show this case is no different.
Instead 2 counters are now used, one for PMIC accesses from the PUnit
and one for accesses from in kernel I2C code. When access is requested
now the code will wait (using a waitqueue) for the counter of the other
type of access to reach 0 and on release, if the counter reaches 0 the
wakequeue is woken.
Note that the counter approach is necessary to allow nested calls.
The main reason for this is so that a series of i2c transfers can be done
with the punit blocked from accessing the bus the whole time. This is
necessary to be able to safely read/modify/write a PMIC register without
racing with the PUNIT doing the same thing.
Allowing nested iosf_mbi_block_punit_i2c_access() calls also is desirable
from a performance pov since the whole dance necessary to block the PUnit
from accessing the PMIC I2C bus is somewhat expensive.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lkml.kernel.org/r/20190812102113.95794-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Force HS200 by masking bit 63 of the SDHCI capability register.
The i.MX ESDHC driver uses SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400. With
that the stack checks bit 63 to descide whether HS400 is available.
Using sdhci-caps-mask allows to mask bit 63. The stack then selects
HS200 as operating mode.
This prevents rare communication errors with minimal effect on
performance:
sdhci-esdhc-imx 30b60000.usdhc: warning! HS400 strobe DLL
status REF not lock!
Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org> Reported-by: Mark Brown <broonie@kernel.org> Reported-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Recent changes to the atheros at803x driver caused
ethernet to stop working on this board.
In particular commit 6d4cd041f0af
("net: phy: at803x: disable delay only for RGMII mode")
and commit cd28d1d6e52e
("net: phy: at803x: Disable phy delay for RGMII mode")
fix the AR8031 driver to configure the phy's (RX/TX)
delays as per the 'phy-mode' in the device tree.
This now prevents ethernet from working on this board.
It used to work before those commits, because the
AR8031 comes out of reset with RX delay enabled, and
the at803x driver didn't touch the delay configuration
at all when "rgmii" mode was selected, and because
arch/arm/mach-imx/mach-imx7d.c:ar8031_phy_fixup()
unconditionally enables TX delay.
Since above commits ar8031_phy_fixup() also has no
effect anymore, and the end-result is that all delays
are disabled in the phy, no ethernet.
Since commit d3b41b6bb49e ("m68k: Dispatch nvram_ops calls to Atari or
Mac functions"), Coldfire builds generate compiler warnings due to the
unconditional inclusion of asm/atarihw.h and asm/macintosh.h.
The inclusion of asm/atarihw.h causes warnings like this:
In file included from ./arch/m68k/include/asm/atarihw.h:25:0,
from arch/m68k/kernel/setup_mm.c:41,
from arch/m68k/kernel/setup.c:3:
./arch/m68k/include/asm/raw_io.h:39:0: warning: "__raw_readb" redefined
#define __raw_readb in_8
In file included from ./arch/m68k/include/asm/io.h:6:0,
from arch/m68k/kernel/setup_mm.c:36,
from arch/m68k/kernel/setup.c:3:
./arch/m68k/include/asm/io_no.h:16:0: note: this is the location of the previous definition
#define __raw_readb(addr) \
...
This issue is resolved by dropping the asm/raw_io.h include. It turns out
that asm/io_mm.h already includes that header file.
Moving the relevant macro definitions helps to clarify this dependency
and make it safe to include asm/atarihw.h.
The other warnings look like this:
In file included from arch/m68k/kernel/setup_mm.c:48:0,
from arch/m68k/kernel/setup.c:3:
./arch/m68k/include/asm/macintosh.h:19:35: warning: 'struct irq_data' declared inside parameter list will not be visible outside of this definition or declaration
extern void mac_irq_enable(struct irq_data *data);
^~~~~~~~
...
This issue is resolved by adding the missing linux/irq.h include.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Greg Ungerer <gerg@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
compile-testing this driver on other architectures showed
multiple warnings:
drivers/net/ethernet/nxp/lpc_eth.c: In function 'lpc_eth_drv_probe':
drivers/net/ethernet/nxp/lpc_eth.c:1337:19: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
drivers/net/ethernet/nxp/lpc_eth.c:1342:19: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
Use format strings that work on all architectures.
Link: https://lore.kernel.org/r/20190809144043.476786-10-arnd@arndb.de Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The generic Makefile.kasan propagates CONFIG_KASAN_SHADOW_OFFSET into
KASAN_SHADOW_OFFSET, but only does so for CONFIG_KASAN_GENERIC.
Since commit:
6bd1d0be0e97936d ("arm64: kasan: Switch to using KASAN_SHADOW_OFFSET")
... arm64 defines CONFIG_KASAN_SHADOW_OFFSET in Kconfig rather than
defining KASAN_SHADOW_OFFSET in a Makefile. Thus, if
CONFIG_KASAN_SW_TAGS && KASAN_INLINE are selected, we get build time
splats due to KASAN_SHADOW_OFFSET not being set:
| [mark@lakrids:~/src/linux]% usellvm 8.0.1 usekorg 8.1.0 make ARCH=arm64 CROSS_COMPILE=aarch64-linux- CC=clang
| scripts/kconfig/conf --syncconfig Kconfig
| CC scripts/mod/empty.o
| clang (LLVM option parsing): for the -hwasan-mapping-offset option: '' value invalid for uint argument!
| scripts/Makefile.build:273: recipe for target 'scripts/mod/empty.o' failed
| make[1]: *** [scripts/mod/empty.o] Error 1
| Makefile:1123: recipe for target 'prepare0' failed
| make: *** [prepare0] Error 2
Let's fix this by always propagating CONFIG_KASAN_SHADOW_OFFSET into
KASAN_SHADOW_OFFSET if CONFIG_KASAN is selected, moving the existing
common definition of +CFLAGS_KASAN_NOSANITIZE to the top of
Makefile.kasan.
Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Tested-by Steve Capper <steve.capper@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Not all sensors will be able to guarantee a proper initial state.
This may be either because the driver is not properly written,
or (probably unlikely) because the hardware won't support it.
While the right solution in the former case is to fix the sensor
driver, the real world not always allows right solutions, due to lack
of available documentation and support on these sensors.
Let's relax this requirement, and allow the driver to support stream start,
even if the sensor initial sequence wasn't the expected.
Also improve the warning message to better explain the problem and provide
a hint that the sensor driver needs to be fixed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Jacopo Mondi <jacopo@jmondi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 5d7936b8e27d ("media: vsp1: Convert display lists to use new body pool") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
# ========
# captured on : Thu Aug 1 22:58:38 2019
# header version : 1
...
# CPU 0: Core ID 0, Socket ID 36
# CPU 1: Core ID 1, Socket ID 36
...
# CPU 126: Core ID 126, Socket ID 8442
# CPU 127: Core ID 127, Socket ID 8442
...
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Tzvetomir Stoyanov (VMware) <tz.stoyanov@gmail.com> Link: http://lkml.kernel.org/r/1564717737-21602-1-git-send-email-tanxiaojun@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Building a combined ARMv4+XScale kernel produces these
and other build failures:
/tmp/copypage-xscale-3aa821.s: Assembler messages:
/tmp/copypage-xscale-3aa821.s:167: Error: selected processor does not support `pld [r7,#0]' in ARM mode
/tmp/copypage-xscale-3aa821.s:168: Error: selected processor does not support `pld [r7,#32]' in ARM mode
/tmp/copypage-xscale-3aa821.s:169: Error: selected processor does not support `pld [r1,#0]' in ARM mode
/tmp/copypage-xscale-3aa821.s:170: Error: selected processor does not support `pld [r1,#32]' in ARM mode
/tmp/copypage-xscale-3aa821.s:171: Error: selected processor does not support `pld [r7,#64]' in ARM mode
/tmp/copypage-xscale-3aa821.s:176: Error: selected processor does not support `ldrd r4,r5,[r7],#8' in ARM mode
/tmp/copypage-xscale-3aa821.s:180: Error: selected processor does not support `strd r4,r5,[r1],#8' in ARM mode
Add an explict .arch armv5 in the inline assembly to allow the ARMv5
specific instructions regardless of the compiler -march= target.
Link: https://lore.kernel.org/r/20190809163334.489360-5-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When compile-testing on other architectures, we get lots of warnings
about incorrect format strings, like:
drivers/dma/iop-adma.c: In function 'iop_adma_alloc_slots':
drivers/dma/iop-adma.c:307:6: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
drivers/dma/iop-adma.c: In function 'iop_adma_prep_dma_memcpy':
>> drivers/dma/iop-adma.c:518:40: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'size_t {aka long unsigned int}' [-Wformat=]
Use %zu for printing size_t as required, and cast the dma_addr_t
arguments to 'u64' for printing with %llx. Ideally this should use
the %pad format string, but that requires an lvalue argument that
doesn't work here.
Link: https://lore.kernel.org/r/20190809163334.489360-3-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Allow selecting the IR protocol, MCE or iMON, for a device that
identifies as follows (with config id 0x7e):
15c2:ffdc SoundGraph Inc. iMON PAD Remote Controller
As the driver is structured to default to iMON when both RC
protocols are supported, existing users of this device (using MCE
protocol) will need to manually switch to MCE (RC-6) protocol from
userspace (with ir-keytable, sysfs).
Signed-off-by: Darius Rad <alpha@area49.net> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit e5adfc3e7e77 ("perf map: Synthesize maps only for thread group
leader") changed the recording side so that we no longer get mmap events
for threads other than the thread group leader (when synthesising these
events for threads which exist before perf is started).
When a file recorded after this change is loaded, the lack of mmap
records mean that unwinding is not set up for any other threads.
This can be seen in a simple record/report scenario:
perf record --call-graph=dwarf -t $TID
perf report
If $TID is a process ID then the report will show call graphs, but if
$TID is a secondary thread the output is as if --call-graph=none was
specified.
Following the rationale in that commit, move the libunwind fields into
struct map_groups and update the libunwind functions to take this
instead of the struct thread. This is only required for
unwind__finish_access which must now be called from map_groups__delete
and the others are changed for symmetry.
Note that unwind__get_entries keeps the thread argument since it is
required for symbol lookup and the libdw unwind provider uses the thread
ID.
Signed-off-by: John Keeping <john@metanate.com> Reviewed-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: e5adfc3e7e77 ("perf map: Synthesize maps only for thread group leader") Link: http://lkml.kernel.org/r/20190815100146.28842-2-john@metanate.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It seems that LLVM's linker does not correctly handle variable assignments
involving section positions that are updated during the SECTIONS
parsing. Commit aa69fb62bea1 ("arm64/efi: Mark __efistub_stext_offset as
an absolute symbol explicitly") ran into this too, but found a different
workaround.
However, this was not enough, as other variables were also miscalculated
which manifested as boot failures under UEFI where __efistub__end was
not taking the correct _end value (they should be the same):
To work around this, all of the __efistub_-prefixed variable assignments
need to be moved after the linker script's SECTIONS entry. As it turns
out, this also solves the problem fixed in commit aa69fb62bea1, so those
changes are reverted here.
Link: https://github.com/ClangBuiltLinux/linux/issues/634 Link: https://bugs.llvm.org/show_bug.cgi?id=42990 Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
i2c_new_dummy() can fail returning a NULL pointer. This is not checked
and the returned pointer is blindly used. Convert to
devm_i2c_new_dummy_client() which returns an ERR_PTR and also add a
validity check. Using devm_* here also fixes a leak because the dummy
client was not released in the probe error path.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
To get the expected output we have to ignore whatever changes the user
has in its ~/.perfconfig file, so set PERF_CONFIG to /dev/null to
achieve that.
Before:
# egrep 'trace|show_' ~/.perfconfig
[trace]
show_zeros = yes
show_duration = no
show_timestamp = no
show_arg_names = no
show_prefix = yes
# echo $PERF_CONFIG
# perf test "trace + vfs_getname"
70: Check open filename arg using perf trace + vfs_getname: FAILED!
# export PERF_CONFIG=/dev/null
# perf test "trace + vfs_getname"
70: Check open filename arg using perf trace + vfs_getname: Ok
#
After:
# egrep 'trace|show_' ~/.perfconfig
[trace]
show_zeros = yes
show_duration = no
show_timestamp = no
show_arg_names = no
show_prefix = yes
# echo $PERF_CONFIG
# perf test "trace + vfs_getname"
70: Check open filename arg using perf trace + vfs_getname: Ok
#
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Taeung Song <treeze.taeung@gmail.com> Link: https://lkml.kernel.org/n/tip-3up27pexg5i3exuzqrvt4m8u@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We had this comment in Documentation/perf_counter/config.c, i.e. since
when we got this from the git sources, but never really did that
getenv("PERF_CONFIG"), do it now as I need to disable whatever
~/.perfconfig root has so that tests parsing tool output are done for
the expected default output or that we specify an alternate config file
that when read will make the tools produce expected output.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Taeung Song <treeze.taeung@gmail.com> Fixes: 078006012401 ("perf_counter tools: add in basic glue from Git") Link: https://lkml.kernel.org/n/tip-jo209zac9rut0dz1rqvbdlgm@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Scheduling-clock interrupts can arrive late in the CPU-offline process,
after idle entry and the subsequent call to cpuhp_report_idle_dead().
Once execution passes the call to rcu_report_dead(), RCU is ignoring
the CPU, which results in lockdep complaints when the interrupt handler
uses RCU:
This happens rarely, but can be forced by happen more often by
placing delays in cpuhp_report_idle_dead() following the call to
rcu_report_dead(). With this in place, the following rcutorture
scenario reproduces the problem within a few minutes:
This commit uses the crude but effective expedient of moving the disabling
of interrupts within the idle loop to precede the cpu_is_offline()
check. It also invokes tick_nohz_idle_stop_tick() instead of
tick_nohz_idle_stop_tick_protected() to shut off the scheduling-clock
interrupt.
Signed-off-by: Peter Zijlstra <peterz@infradead.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org>
[ paulmck: Revert tick_nohz_idle_stop_tick_protected() removal, new callers. ] Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Enabling WARN_DOUBLE_CLOCK in /sys/kernel/debug/sched_features causes
warning to fire in update_rq_clock. This seems to be caused by onlining
a new fair sched group not using the rq lock wrappers.
Sometimes platfom may take too long to respond to the command and OS
might timeout before platform transfer the ownership of the shared
memory region to the OS with the response.
Since the mailbox channel associated with the channel is freed and new
commands are dispatch on the same channel, OS needs to wait until it
gets back the ownership. If not, either OS may end up overwriting the
platform response for the last command(which is fine as OS timed out
that command) or platform might overwrite the payload for the next
command with the response for the old.
The latter is problematic as platform may end up interpretting the
response as the payload. In order to avoid such race, let's wait until
the OS gets back the ownership before we prepare the shared memory with
the payload for the next command.
Reported-by: Jim Quinlan <james.quinlan@broadcom.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
AER info of PCIe fatal error is not printed in the current driver.
Because APEI driver will panic directly for fatal error, and can't
run to the place of printing AER info.
An example log is as following:
{763}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 11
{763}[Hardware Error]: event severity: fatal
{763}[Hardware Error]: Error 0, type: fatal
{763}[Hardware Error]: section_type: PCIe error
{763}[Hardware Error]: port_type: 0, PCIe end point
{763}[Hardware Error]: version: 4.0
{763}[Hardware Error]: command: 0x0000, status: 0x0010
{763}[Hardware Error]: device_id: 0000:82:00.0
{763}[Hardware Error]: slot: 0
{763}[Hardware Error]: secondary_bus: 0x00
{763}[Hardware Error]: vendor_id: 0x8086, device_id: 0x10fb
{763}[Hardware Error]: class_code: 000002
Kernel panic - not syncing: Fatal hardware error!
This issue was imported by the patch, '37448adfc7ce ("aerdrv: Move
cper_print_aer() call out of interrupt context")'. To fix this issue,
this patch adds print of AER info in cper_print_pcie() for fatal error.
Here is the example log after this patch applied:
{24}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 10
{24}[Hardware Error]: event severity: fatal
{24}[Hardware Error]: Error 0, type: fatal
{24}[Hardware Error]: section_type: PCIe error
{24}[Hardware Error]: port_type: 0, PCIe end point
{24}[Hardware Error]: version: 4.0
{24}[Hardware Error]: command: 0x0546, status: 0x4010
{24}[Hardware Error]: device_id: 0000:01:00.0
{24}[Hardware Error]: slot: 0
{24}[Hardware Error]: secondary_bus: 0x00
{24}[Hardware Error]: vendor_id: 0x15b3, device_id: 0x1019
{24}[Hardware Error]: class_code: 000002
{24}[Hardware Error]: aer_uncor_status: 0x00040000, aer_uncor_mask: 0x00000000
{24}[Hardware Error]: aer_uncor_severity: 0x00062010
{24}[Hardware Error]: TLP Header: 000000c0010100000000000100000000
Kernel panic - not syncing: Fatal hardware error!
Fixes: 37448adfc7ce ("aerdrv: Move cper_print_aer() call out of interrupt context") Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Reviewed-by: James Morse <james.morse@arm.com>
[ardb: put parens around terms of && operator] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Depending on how BIOS has marked the reserved region containing the 32KB
MCHBAR you can get warnings like:
resource sanity check: requesting [mem 0xfed10000-0xfed1ffff], which spans more than reserved [mem 0xfed10000-0xfed17fff]
caller dnv_rd_reg+0xc8/0x240 [pnd2_edac] mapping multiple BARs
Not all of the mmio regions used in dnv_rd_reg() are the same size. The
MCHBAR window is 32KB and the sideband ports are 64KB. Pass the correct
size to ioremap() depending on which resource we're reading from.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
These paths point to the wrong location but still work because they get
picked up by a -I flag that happens to direct to the correct file. Fix
paths to lead to the actual file location without help from include
flags.
Signed-off-by: Luke Mujica <lukemujica@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/r/20190719202253.220261-1-lukemujica@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Enabling Direct I/O with loop devices helps reducing memory usage by
avoiding double caching. 32 bit applications running on 64 bits systems
are currently not able to request direct I/O because is missing from the
lo_compat_ioctl.
This patch fixes the compatibility issue mentioned above by exporting
LOOP_SET_DIRECT_IO as additional lo_compat_ioctl() entry.
The input argument for this ioctl is a single long converted to a 1-bit
boolean, so compatibility is preserved.
Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Alessio Balsini <balsini@android.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The processors marked as 0xff are invalid, there are only 8 of them in
this case.
So do not print an error on ids == 0xff, just print an info message.
Actually, we could return ENODEV even on the first CPU with ID 0xff, but
ACPI spec does not forbid the 0xff value to be a processor ID. Given
0xff could be a correct one, we would break working systems if we
returned ENODEV.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There is a race between hda codec device removing and the
jack-detecting work, which will lead to a page fault issue as the
latter work is accessing codec device which could be already removed.
Here add the cancellation of jack-detecting work before codecs are actually
removed to avoid the race and fix the issue.
Bug: https://github.com/thesofproject/linux/issues/1067 Signed-off-by: Keyon Jie <yang.jie@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190807145030.26117-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In addition, the 0day bot reported this build error:
>> drivers/ras/debugfs.c:10:5: error: redefinition of 'ras_userspace_consumers'
int ras_userspace_consumers(void)
^~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/ras/debugfs.c:3:0:
include/linux/ras.h:14:19: note: previous definition of 'ras_userspace_consumers' was here
static inline int ras_userspace_consumers(void) { return 0; }
^~~~~~~~~~~~~~~~~~~~~~~
for a riscv-specific .config where CONFIG_DEBUG_FS is not set. Fix all
that by making debugfs.o depend on that define.
[ bp: Rewrite commit message. ]
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Tony Luck <tony.luck@intel.com> Cc: linux-edac@vger.kernel.org Cc: x86@kernel.org Link: http://lkml.kernel.org/r/7053.1565218556@turing-police Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If IOMMU_SUPPORT is not set, and COMPILE_TEST is y,
IOMMU_IOVA may be set to m. So building will fails:
drivers/staging/media/tegra-vde/iommu.o: In function `tegra_vde_iommu_map':
iommu.c:(.text+0x41): undefined reference to `alloc_iova'
iommu.c:(.text+0x56): undefined reference to `__free_iova'
Select IOMMU_IOVA while COMPILE_TEST is set to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com> Suggested-by: Dmitry Osipenko <digetx@gmail.com> Fixes: b301f8de1925 ("media: staging: media: tegra-vde: Add IOMMU support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
arch/microblaze/ defines out_be32() and in_be32(), so don't do that
again in the driver source.
Fixes these build warnings:
../drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined
../arch/microblaze/include/asm/io.h:50: note: this is the location of the previous definition
../drivers/media/platform/fsl-viu.c:37: warning: "in_be32" redefined
../arch/microblaze/include/asm/io.h:53: note: this is the location of the previous definition
Fixes: 29d750686331 ("media: fsl-viu: allow building it with COMPILE_TEST") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Then from kernel side, Manage_add invokes the path (add_new_disk ->
validate_super = super_1_validate) to set In_sync flag.
Since In_sync means "device is in_sync with rest of array", and the new
added disk need to resync thread to help the synchronization of data.
And md_reap_sync_thread would call spare_active to set In_sync for the
new added disk finally. So don't set In_sync if array is in frozen.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When add one disk to array, the md_reap_sync_thread is responsible
to activate the spare and set In_sync flag for the new member in
spare_active().
But if raid1 has one member disk A, and disk B is added to the array.
Then we offline A before all the datas are synchronized from A to B,
obviously B doesn't have the latest data as A, but B is still marked
with In_sync flag.
So let's not call spare_active under the condition, otherwise B is
still showed with 'U' state which is not correct.
Signed-off-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When write bio return error, it would be added to conf->retry_list
and wait for raid1d thread to retry write and acknowledge badblocks.
In narrow_write_error(), the error bio will be split in the unit of
badblock shift (such as one sector) and raid1d thread issues them
one by one. Until all of the splited bio has finished, raid1d thread
can go on processing other things, which is time consuming.
But, there is a scene for error handling that is not necessary.
When the device has been set faulty, flush_bio_list() may end
bios in pending_bio_list with error status. Since these bios
has not been issued to the device actually, error handlding to
retry write and acknowledge badblocks make no sense.
Even without that scene, when the device is faulty, badblocks info
can not be written out to the device. Thus, we also no need to
handle the error IO.
Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The commit d5370f754875 ("arm64: prefetch: add alternative pattern for
CPUs without a prefetcher") introduced MIDR_IS_CPU_MODEL_RANGE() to be
used in has_no_hw_prefetch() with rv_min=0 which generates a compilation
warning from GCC,
In file included from ./arch/arm64/include/asm/cache.h:8,
from ./include/linux/cache.h:6,
from ./include/linux/printk.h:9,
from ./include/linux/kernel.h:15,
from ./include/linux/cpumask.h:10,
from arch/arm64/kernel/cpufeature.c:11:
arch/arm64/kernel/cpufeature.c: In function 'has_no_hw_prefetch':
./arch/arm64/include/asm/cputype.h:59:26: warning: comparison of
unsigned expression >= 0 is always true [-Wtype-limits]
_model == (model) && rv >= (rv_min) && rv <= (rv_max); \
^~
arch/arm64/kernel/cpufeature.c:889:9: note: in expansion of macro
'MIDR_IS_CPU_MODEL_RANGE'
return MIDR_IS_CPU_MODEL_RANGE(midr, MIDR_THUNDERX,
^~~~~~~~~~~~~~~~~~~~~~~
Fix it by converting MIDR_IS_CPU_MODEL_RANGE to a static inline
function.
Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ADG is using clk_get_rate() under atomic context, thus, we might
have scheduling issue.
To avoid this issue, we need to get/keep clk rate under
non atomic context.
We need to handle ADG as special device at Renesas Sound driver.
From SW point of view, we want to impletent it as
rsnd_mod_ops :: prepare, but it makes code just complicate.
To avoid complicated code/patch, this patch adds new clk_rate[] array,
and keep clk IN rate when rsnd_adg_clk_enable() was called.
Reported-by: Leon Kong <Leon.KONG@cn.bosch.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Leon Kong <Leon.KONG@cn.bosch.com> Link: https://lore.kernel.org/r/87v9vb0xkp.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Linux kernel assumes that get_endpoint(alts,0) and
get_endpoint(alts,1) are eachothers feedback endpoints.
To reassure that validity it will test bsynchaddress to comply with that
assumption. But if the bsyncaddress is 0 (invalid), it will flag that as
a wrong assumption and return an error.
Fix: Skip the test if bSynchAddress is 0.
Note: those with a valid bSynchAddress should have a code quirck added.
Signed-off-by: Ard van Breemen <ard@kwaak.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In order to protect clock measuring when multiple process asks for
a measure, protect the main measure function with mutexes.
Reviewed-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We should free the initrd reserved memblock in an aligned manner,
because the initrd reserves the memblock in an aligned manner
in arm64_memblock_init().
Otherwise there are some fragments in memblock_reserved regions
after free_initrd_mem(). e.g.:
/sys/kernel/debug/memblock # cat reserved
0: 0x0000000080080000..0x00000000817fafff
1: 0x0000000083400000..0x0000000083ffffff
2: 0x0000000090000000..0x000000009000407f
3: 0x00000000b0000000..0x00000000b000003f
4: 0x00000000b26184ea..0x00000000b2618fff
The fragments like the ranges from b0000000 to b000003f and
from b26184ea to b2618fff should be freed.
And we can do free_reserved_area() after memblock_free(),
as free_reserved_area() calls __free_pages(), once we've done
that it could be allocated somewhere else,
but memblock and iomem still say this is reserved memory.
Fixes: 05c58752f9dc ("arm64: To remove initrd reserved area entry from memblock") Signed-off-by: Junhua Huang <huang.junhua@zte.com.cn> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The TEO goveror prevents the scheduler tick from being stopped (unless
stopped already) if there is a PM QoS latency constraint for the given
CPU and the target residency of the deepest idle state matching that
constraint is below the tick boundary.
However, that is problematic if CPUs with PM QoS latency constraints
are idle for long times, because it effectively causes the tick to
run on them all the time which is wasteful. [It is also confusing
and questionable if they are full dynticks CPUs.]
To address that issue, modify the TEO governor to carry out the
entire search for the most suitable idle state (from the target
residency perspective) even if a latency constraint is present,
to allow it to determine the expected idle duration in all cases.
Also, when using the last several measured idle duration values
to refine the idle state selection, make it compare those values
with the current expected idle duration value (instead of
comparing them with the target residency of the idle state
selected so far) which should prevent the tick from being
retained when it makes sense to stop it sometimes (especially
in the presence of PM QoS latency constraints).
Fixes: b26bf6ab716f ("cpuidle: New timer events oriented governor for tickless systems") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver needs to check the endpoint types, too, as opposed
to the number of endpoints. This also requires moving the check earlier.
Reported-by: syzbot+01a77b82edaa374068e1@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to latest datasheet (Rev.1, 10/2018) from below links,
in the consumer datasheet, 1.5GHz is mentioned as highest opp but
depends on speed grading fuse, and in the industrial datasheet,
1.3GHz is mentioned as highest opp but depends on speed grading
fuse. 1.5GHz and 1.3GHz opp use same voltage, so no need for
consumer part to support 1.3GHz opp, with same voltage, CPU should
run at highest frequency in order to go into idle as quick as
possible, this can save power.
That means for consumer part, 1GHz/1.5GHz are supported, for
industrial part, 800MHz/1.3GHz are supported, and then check the
speed grading fuse to limit the highest CPU frequency further.
Correct the market segment bits in opp table to make them work
according to datasheets.
The synchronize_rcu_expedited() function has an INIT_WORK_ONSTACK(),
but lacks the corresponding destroy_work_on_stack(). This commit
therefore adds destroy_work_on_stack().
Reported-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Acked-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In build_adc_controls(), there is an if statement on line 773 to check
whether ak->adc_info is NULL:
if (! ak->adc_info ||
! ak->adc_info[mixer_ch].switch_name)
When ak->adc_info is NULL, it is used on line 792:
knew.name = ak->adc_info[mixer_ch].selector_name;
Thus, a possible null-pointer dereference may occur.
To fix this bug, referring to lines 773 and 774, ak->adc_info
and ak->adc_info[mixer_ch].selector_name are checked before being used.
This bug is found by a static analysis tool STCheck written by us.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The last fallback of CORB/RIRB communication error recovery is to turn
on the single command mode, and this last resort usually means that
something is really screwed up. Instead of a normal dev_err(), show
the error more clearly with dev_WARN() with the caller stack trace.
Also, show the bus-reset fallback also as an error, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-eoan-kernel.git / log