MIPS: Adjust set_pte() SMP fix to handle R10000_LLSC_WAR
Update the recent changes to set_pte() that were added in 46011e6ea392
to handle R10000_LLSC_WAR, and format the assembly to match other areas
of the MIPS tree using the same WAR.
This also incorporates a patch recently sent in my Markos Chandras,
"Remove local LL/SC preprocessor variants", so that patch doesn't need
to be applied if this one is accepted.
James Hogan [Fri, 15 Apr 2016 09:07:26 +0000 (10:07 +0100)]
MIPS: Fix MSA assembly warnings
Building an MSA capable kernel with a toolchain that supports MSA
produces warnings such as this:
arch/mips/kernel/r4k_fpu.S:229: Warning: the `msa' extension requires 64-bit FPRs
This is due to ".set msa" without ".set fp=64" in the non doubleword MSA
load/store macros, since MSA requires the 64-bit FPU registers (FR=1).
Add the missing fp=64 in these macros to silence the warnings.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13063/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 15 Apr 2016 09:07:25 +0000 (10:07 +0100)]
MIPS: Fix MSA assembly with big thread offsets
When lockdep is enabled on a 64-bit kernel the FPR offset into the
thread structure exceeds the maximum range of the MSA ld.d/st.d
instructions. For example THREAD_FPR31 = 4644 (instead of 2448), while
the signed immediate field is only 10 bits with an implicit multiply by
8, giving a maximum offset of 511*8 = 4088.
This isn't a problem when the toolchain doesn't support MSA as the
ld_*/st_* macros perform the addition separately into $1 with [d]addui
which has a 16bit signed immediate field.
Fix the case where the toolchain does support MSA by doing a single
addition of THREAD_FPR0 into $1 with [d]addui, and doing the ld_*/st_*
relative to that.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13064/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 15 Apr 2016 09:07:24 +0000 (10:07 +0100)]
MIPS: Fix MSA ld_*/st_* asm macros to use PTR_ADDU
The MSA ld_*/st_* assembler macros for when the toolchain doesn't
support MSA use addu to offset the base address. However it is a virtual
memory pointer so fix it to use PTR_ADDU which expands to daddu for
64-bit kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.3.y-
Patchwork: https://patchwork.linux-mips.org/patch/13062/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Burton [Fri, 15 Apr 2016 09:07:23 +0000 (10:07 +0100)]
MIPS: Use copy_s.fmt rather than copy_u.fmt
In revision 1.12 of the MSA specification, the copy_u.w instruction has
been removed for MIPS32 & the copy_u.d instruction has been removed for
MIPS64. Newer toolchains (eg. Codescape SDK essentials 2015.10) will
complain about this like so:
arch/mips/kernel/r4k_fpu.S:290: Error: opcode not supported on this
processor: mips32r2 (mips32r2) `copy_u.w $1,$w26[3]'
Since we always copy to the width of a GPR, simply use copy_s instead of
copy_u to fix this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.3.x+
Patchwork: https://patchwork.linux-mips.org/patch/13061/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matt Redfearn [Mon, 21 Dec 2015 15:21:42 +0000 (15:21 +0000)]
MIPS: dma-default: Defend against NULL dev in massage_gfp_flags
This patch ensures that the dev parameter is checked for NULL before it
is dereferenced in massage_gfp_flags. If dev is NULL, then fall back
setting the GFP flag requested and available.
Yanjiang Jin [Wed, 9 Dec 2015 03:15:27 +0000 (11:15 +0800)]
MIPS: oprofile: Fix a preemption issue
Use boot_cpu_type() instead of current_cpu_type() in oprofile_arch_init()
to avoid the below warning, cpu_type is normally consistent in a MIPS SMP
system. There are a few exceptions such as SGI servers where it is
possible to mix R10000, R12000, R14000 and R16000 within certain
constraints. Let's not worry about those now.
Huacai Chen [Thu, 17 Mar 2016 12:41:06 +0000 (20:41 +0800)]
MIPS: Loongson-3: Fix build error after ld-version.sh modification
Commit d5ece1cb074b2c ("Fix ld-version.sh to handle large 3rd version
part") modifies the ld version description. This causes a build error
on Loongson-3, so fix it.
Huacai Chen [Thu, 17 Mar 2016 12:41:05 +0000 (20:41 +0800)]
MIPS: Loongson-3: Reserve 32MB for RS780E integrated GPU
Due to datasheet, reserving 0xff800000~0xffffffff (8MB below 4GB) is
not enough for RS780E integrated GPU's TOM (top of memory) registers
and MSI/MSI-x memory region, so we reserve 0xfe000000~0xffffffff (32MB
below 4GB).
Huacai Chen [Thu, 17 Mar 2016 12:37:10 +0000 (20:37 +0800)]
MIPS: Reserve nosave data for hibernation
After commit 92923ca3aacef63c92d ("mm: meminit: only set page reserved
in the memblock region"), the MIPS hibernation is broken. Because pages
in nosave data section should be "reserved", but currently they aren't
set to "reserved" at initialization. This patch makes hibernation work
again.
Andreas Ruprecht [Thu, 16 Jul 2015 15:52:11 +0000 (17:52 +0200)]
MIPS: Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER
Commit 6793f55cbc84 ("MIPS: sibyte: Amend dependencies for
SIBYTE_BUS_WATCHER") changed the dependencies for
SIBYTE_BUS_WATCHER to make it visible only if SIBYTE_BCM112X
or SIBYTE_SB1250 are enabled.
In the code in arch/mips/sibyte/common/bus_watcher, however,
a #if defined() check suggests that this functionality should
also be available for SIBYTE_BCM1x55 and SIBYTE_BCM1x80.
Make it selectable by extending the dependencies of
SIBYTE_BUS_WATCHER in arch/mips/sibyte/Kconfig.
James Hogan [Fri, 22 Jan 2016 10:58:26 +0000 (10:58 +0000)]
MIPS: I6400: Icache fills from dcache
Coherence Manager 3 (CM3) as present in I6400 can fill icache lines
effectively from dirty dcaches, so there is no need to flush dirty lines
from dcaches through to L2 prior to icache invalidation.
Set the MIPS_CACHE_IC_F_DC flag such that cpu_has_ic_fills_f_dc
evaluates to true, which avoids those dcache flushes.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: Manuel Lauss <manuel.lauss@gmail.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12180/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 22 Jan 2016 10:58:25 +0000 (10:58 +0000)]
MIPS: c-r4k: Sync icache when it fills from dcache
It is still necessary to handle icache coherency in flush_cache_range()
and copy_to_user_page() when the icache fills from the dcache, even
though the dcache does not need to be written back. However when this
handling was added in commit 2eaa7ec286db ("[MIPS] Handle I-cache
coherency in flush_cache_range()"), it did not do any icache flushing
when it fills from dcache.
Therefore fix r4k_flush_cache_range() to run
local_r4k_flush_cache_range() without taking into account whether icache
fills from dcache, so that the icache coherency gets handled. Checks are
also added in local_r4k_flush_cache_range() so that the dcache blast
doesn't take place when icache fills from dcache.
A test to mmap a page PROT_READ|PROT_WRITE, modify code in it, and
mprotect it to VM_READ|VM_EXEC (similar to case described in above
commit) can hit this case quite easily to verify the fix.
A similar check was added in commit f8829caee311 ("[MIPS] Fix aliasing
bug in copy_to_user_page / copy_from_user_page"), so also fix
copy_to_user_page() similarly, to call flush_cache_page() without taking
into account whether icache fills from dcache, since flush_cache_page()
already takes that into account to avoid performing a dcache flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: Manuel Lauss <manuel.lauss@gmail.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12179/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Tue, 1 Mar 2016 22:19:37 +0000 (22:19 +0000)]
MIPS: Enable ptrace hw watchpoints on MIPS R6
HARDWARE_WATCHPOINTS isn't being enabled for CPU_MIPSR6, even though it
has an identical hardware watchpoint interface to CPU_MIPSR2, which
prevents ptrace watchpoints from being loaded when executing a ptraced
process even though the watchpoints are described in /proc/cpuinfo.
James Hogan [Tue, 1 Mar 2016 22:19:36 +0000 (22:19 +0000)]
MIPS: Fix watchpoint restoration
Commit f51246efee2b ("MIPS: Get rid of finish_arch_switch().") moved the
__restore_watch() call from finish_arch_switch() (i.e. after resume()
returns) to before the resume() call in switch_to(). This results in
watchpoints only being restored when a task is descheduled, preventing
the watchpoints from being effective most of the time, except due to
chance before the watchpoints are lazily removed.
Fix the call sequence from switch_to() through to
mips_install_watch_registers() to pass the task_struct pointer of the
next task, instead of using current. This allows the watchpoints for the
next (non-current) task to be restored without reintroducing
finish_arch_switch().
Fixes: f51246efee2b ("MIPS: Get rid of finish_arch_switch().") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 4.3.x-
Patchwork: https://patchwork.linux-mips.org/patch/12726/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Fri, 4 Dec 2015 22:25:02 +0000 (22:25 +0000)]
MIPS: Avoid using unwind_stack() with usermode
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/11701/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9)
James Hogan [Fri, 4 Dec 2015 22:25:01 +0000 (22:25 +0000)]
MIPS: Don't unwind to user mode with EVA
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.15+
Patchwork: https://patchwork.linux-mips.org/patch/11700/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS: BMIPS: Add missing 7038 L1 register cells to BCM7435
7435 has 4 7038 L1 base register address for each of its Core + TP (for a total
of 4 threads of execution), add the two missing cells for Core 1. We are
providing HW interrupts 2/3 even for Core 1/TP0/TP1 because that's what they
are, and we can later decide to remap these in software to provide proper
interrupt affinity/parenting.
Import bmips_5xxx_init.S from the stblinux-3.3 tree, and to make sure that this
would work nicely with a BMIPS multiplatform kernel (with BMIPS330, BMIPS43XX
and BMIPS5000 enabled), update soft_reset to check for the BMIPS5200 processor
id (PRID_IMP_BMIPS5200) and execute bmips_5xxx_init for these processors to
bring them online.
Tested on 7425, 7429 and 7435 with CPU hotplug. 7435 SMP still needs some
additional changes in the L1 interrupt area to work properly with interrupt
affinity.
Florian Fainelli [Sat, 30 Jan 2016 05:17:26 +0000 (21:17 -0800)]
MIPS: BMIPS: Fix PRID_IMP_BMIPS5000 masking for BMIPS5200
BMIPS5000 have a PrID value of 0x5A00 and BMIPS5200 have a PrID value of
0x5B00, which, masked with 0x5A00, returns 0x5A00. Update all conditionals on
the PrID to cover both variants since we are going to need this to enable
BMIPS5200 SMP. The existing check, masking with 0xFF00 would not cover
BMIPS5200 at all.
Paul Burton [Mon, 4 Apr 2016 09:04:52 +0000 (10:04 +0100)]
MIPS: Don't BUG_ON when no IPI domain is found
Commit fbde2d7d8290 ("MIPS: Add generic SMP IPI support") introduced
code that BUG_ON's in the case of a kernel that supports IPI domains but
does not have one at runtime. This case is possible on Malta where for
IPIs we may use either the GIC (which has an IPI IRQ domain
implementation) or core-local software interrupts between VPEs (which do
not currently have an IPI IRQ domain implementation). We can not know
which will be used until runtime when we know whether a GIC is actually
present, and if we run on a system with multiple VPEs and no GIC then
the BUG_ON is hit.
Commit 19fb5818ed60 ("IPS: Fix broken malta qemu") worked around this
for the single-core single-VPE case typically seen using QEMU, but does
not catch the multi-VPE case. This patch removes the insufficient CPU
presence check that was added and works around the bug differently,
effectively reverting that commit.
A simple way to reproduce this bug is by using QEMU, which partially
implements the MT ASE but does not implement the GIC as of version 2.5.
Using "-cpu 34Kf -smp 2" will present a system with 2 VPEs in one core &
no GIC, hitting the BUG_ON.
Given that we're post-merge-window on the way to v4.6, avoid this by
just returning from mips_smp_ipi_init when no IPI IRQ domain is found.
Ideally at some point all IPI implementations would be converted to the
same IPI IRQ domain interface & we'd be able to restore the check.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Qais Yousef <qsyousef@gmail.com> Fixes: fbde2d7d8290 ("MIPS: Add generic SMP IPI support") Fixes: 19fb5818ed60 ("IPS: Fix broken malta qemu")
Reverts: 19fb5818ed60 ("IPS: Fix broken malta qemu") Cc: Qais Yousef <qsyousef@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Alex Smith <alex.smith@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13007/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
James Hogan [Mon, 8 Feb 2016 18:43:49 +0000 (18:43 +0000)]
MIPS: Fix siginfo.h to use strict posix types
Commit 85efde6f4e0d ("make exported headers use strict posix types")
changed the asm-generic siginfo.h to use the __kernel_* types, and
commit 3a471cbc081b ("remove __KERNEL_STRICT_NAMES") make the internal
types accessible only to the kernel, but the MIPS implementation hasn't
been updated to match.
Switch to proper types now so that the exported asm/siginfo.h won't
produce quite so many compiler errors when included alone by a user
program.
As part of handling a crash on an SMP system, an IPI is send to
all other CPUs to save their current registers and stop. It was
using task_pt_regs(current) to get the registers, but that will
only be accurate if the CPU was interrupted running in userland.
Instead allow the architecture to pass in the registers (all
pass NULL now, but allow for the future) and then use get_irq_regs()
which should be accurate as we are in an interrupt. Fall back to
task_pt_regs(current) if nothing else is available.
Linus Torvalds [Sat, 7 May 2016 17:50:48 +0000 (10:50 -0700)]
Merge tag 'staging-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO driver fixes from Grek KH:
"It's really just IIO drivers here, some small fixes that resolve some
'crash on boot' errors that have shown up in the -rc series, and other
bugfixes that are required.
All have been in linux-next with no reported problems"
* tag 'staging-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: imu: mpu6050: Fix name/chip_id when using ACPI
iio: imu: mpu6050: fix possible NULL dereferences
iio:adc:at91-sama5d2: Repair crash on module removal
iio: ak8975: fix maybe-uninitialized warning
iio: ak8975: Fix NULL pointer exception on early interrupt
Linus Torvalds [Sat, 7 May 2016 17:47:03 +0000 (10:47 -0700)]
Merge tag 'usb-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some last-remaining fixes for USB drivers to resolve issues
that have shown up in testing. And two new device ids as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USB / PM: Allow USB devices to remain runtime-suspended when sleeping"
usb: musb: jz4740: fix error check of usb_get_phy()
Revert "usb: musb: musb_host: Enable HCD_BH flag to handle urb return in bottom half"
usb: musb: gadget: nuke endpoint before setting its descriptor to NULL
USB: serial: cp210x: add Straizona Focusers device ids
USB: serial: cp210x: add ID for Link ECU
Linus Torvalds [Sat, 7 May 2016 15:27:35 +0000 (08:27 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"These are a number of updates to fix a few problems found in the ARM
nommu code over the last couple of years, caused mostly by changes on
the mmu side"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8573/1: domain: move {set,get}_domain under config guard
ARM: 8572/1: nommu: change memory reserve for the vectors
ARM: 8571/1: nommu: fix PMSAv7 setup
Linus Torvalds [Sat, 7 May 2016 15:17:45 +0000 (08:17 -0700)]
Merge tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- deadlock fixes on driver probe at exynos4-is and s43-camif drivers
- a build breakage if media controller is enabled and USB or PCI is
built as module.
* tag 'media/v4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: fix builds when USB or PCI is compiled as module
[media] media: s3c-camif: fix deadlock on driver probe()
[media] media: exynos4-is: fix deadlock on driver probe
Linus Torvalds [Fri, 6 May 2016 20:08:35 +0000 (13:08 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull writeback fix from Jens Axboe:
"Just a single fix for domain aware writeback, fixing a regression that
can cause balance_dirty_pages() to keep looping while not getting any
work done"
* 'for-linus' of git://git.kernel.dk/linux-block:
writeback: Fix performance regression in wb_over_bg_thresh()
Linus Torvalds [Fri, 6 May 2016 19:59:27 +0000 (12:59 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This contains two fixes: a boot fix for older SGI/UV systems, and an
APIC calibration fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
x86/platform/UV: Bring back the call to map_low_mmrs in uv_system_init
Linus Torvalds [Fri, 6 May 2016 18:58:45 +0000 (11:58 -0700)]
Merge tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for problems introduced or discovered recently (intel_pstate,
sti-cpufreq, ARM64 cpuidle, Operating Performance Points framework,
generic device properties framework) and one fix for a hotplug-related
deadlock in ACPICA that's been there forever, but is nasty enough.
Specifics:
- Fix for a recent regression in the intel_pstate driver causing it
to fail to restore the HWP (HW-managed P-states) configuration of
the boot CPU after suspend-to-RAM (Rafael Wysocki).
- Fix for two recent regressions in the intel_pstate driver, one that
can trigger a divide by zero if the driver is accessed via sysfs
before it manages to take the first sample and one causing it to
fail to update a structure field used in a trace point, so the
information coming from it is less useful (Rafael Wysocki).
- Fix for a problem in the sti-cpufreq driver introduced during the
4.5 cycle that causes it to break CPU PM in multi-platform kernels
by registering cpufreq-dt (which subsequently doesn't work)
unconditionally and preventing the driver that would actually work
from registering (Sudeep Holla).
- Stable-candidate fix for an ARM64 cpuidle issue causing idle state
usage counters to be incorrectly updated for idle states that were
not entered due to errors (James Morse).
- Fix for a recently introduced issue in the OPP (Operating
Performance Points) framework causing it to print bogus error
messages for missing optional regulators (Viresh Kumar).
- Fix for a recently introduced issue in the generic device
properties framework that may cause it to attempt to dereferece and
invalid pointer in some cases (Heikki Krogerus).
- Fix for a deadlock in the ACPICA core that may be triggered by
device (eg Thunderbolt) hotplug (Prarit Bhargava)"
* tag 'pm+acpi-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Remove useless check
ACPICA: Dispatcher: Update thread ID for recursive method calls
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
device property: Avoid potential dereferences of invalid pointers
Linus Torvalds [Fri, 6 May 2016 18:53:27 +0000 (11:53 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"This contains a single fix that fixes a nohz tick stopping bug when
mixed-poliocy SCHED_FIFO and SCHED_RR tasks are present on a runqueue"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz/full, sched/rt: Fix missed tick-reenabling bug in sched_can_stop_tick()
Linus Torvalds [Fri, 6 May 2016 18:40:24 +0000 (11:40 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree contains two fixes: new Intel CPU model numbers and an
AMD/iommu uncore PMU driver fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/iommu: Do not register a task ctx for uncore like PMUs
perf/x86: Add model numbers for Kabylake CPUs
Linus Torvalds [Fri, 6 May 2016 18:33:02 +0000 (11:33 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"This tree contains three fixes: a console spam fix, a file pattern fix
and a sysfb_efi fix for a bug that triggered on older ThinkPads"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sysfb_efi: Fix valid BAR address range check
x86/efi-bgrt: Switch all pr_err() to pr_notice() for invalid BGRT
MAINTAINERS: Remove asterisk from EFI directory names
Linus Torvalds [Fri, 6 May 2016 18:27:05 +0000 (11:27 -0700)]
Merge branch 'parisc-4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"Patch from Dmitry V Levin to fix a kernel crash when a straced process
calls the (invalid) syscall which is equal to value of __NR_Linux_syscalls"
* 'parisc-4.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
Linus Torvalds [Fri, 6 May 2016 18:14:38 +0000 (11:14 -0700)]
Merge tag 'arc-4.6-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Late in the cycle, but this has fixes for couple of issues: a PAE40
boot crash and Arnd spotting lack of barriers in BE io-accessors.
The 3rd patch for enabling highmem in low physical mem ;-) honestly is
more than a "fix" but its been in works for some time, seems to be
stable in testing and enables 2 of our customers to go forward with
4.6 kernel.
- Fix for PTE truncation in PAE40 builds
- Fix for big endian IO accessors lacking IO barrier
- Allow HIGHMEM to work with low physical addresses"
* tag 'arc-4.6-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: support HIGHMEM even without PAE40
ARC: Fix PAE40 boot failures due to PTE truncation
ARC: Add missing io barriers to io{read,write}{16,32}be()
Linus Torvalds [Fri, 6 May 2016 17:59:53 +0000 (10:59 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Fixes for i915, amdgpu/radeon and imx.
The IMX fix is for an autoloading regression found in Fedora. The
radeon fixes, are the same fix to amdgpu/radeon to avoid a hardware
lockup in some circumstances with a bad mode, and a double free bug I
took a few hours chasing down the other morning.
The i915 fixes are across the board, all stable material, and fixing
some hangs and suspend/resume issues, along with a live status
regressions"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
gpu: ipu-v3: Fix imx-ipuv3-crtc module autoloading
drm/amdgpu: make sure vertical front porch is at least 1
drm/radeon: make sure vertical front porch is at least 1
drm/amdgpu: set metadata pointer to NULL after freeing.
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
drm/i915: Fake HDMI live status
drm/i915: Fix eDP low vswing for Broadwell
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
drm/i915: Fix system resume if PCI device remained enabled
drm/i915: Avoid stalling on pending flips for legacy cursor updates
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
Do not load one entry beyond the end of the syscall table when the
syscall number of a traced process equals to __NR_Linux_syscalls.
Similar bug with regular processes was fixed by commit 3bb457af4fa8
("[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls").
Merge branches 'pm-opp-fixes', 'pm-cpufreq-fixes' and 'pm-cpuidle-fixes'
* pm-opp-fixes:
PM / OPP: Remove useless check
* pm-cpufreq-fixes:
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
* pm-cpuidle-fixes:
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
Linus Torvalds [Fri, 6 May 2016 03:48:35 +0000 (20:48 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"14 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
byteswap: try to avoid __builtin_constant_p gcc bug
lib/stackdepot: avoid to return 0 handle
mm: fix kcompactd hang during memory offlining
modpost: fix module autoloading for OF devices with generic compatible property
proc: prevent accessing /proc/<PID>/environ until it's ready
mm/zswap: provide unique zpool name
mm: thp: kvm: fix memory corruption in KVM with THP enabled
MAINTAINERS: fix Rajendra Nayak's address
mm, cma: prevent nr_isolated_* counters from going negative
mm: update min_free_kbytes from khugepaged after core initialization
huge pagecache: mmap_sem is unlocked when truncation splits pmd
rapidio/mport_cdev: fix uapi type definitions
mm: memcontrol: let v2 cgroups follow changes in system swappiness
mm: thp: correct split_huge_pages file permission
Linus Torvalds [Fri, 6 May 2016 01:10:01 +0000 (18:10 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- a fix for the persistent memory 'struct page' driver. The
implementation overlooked the fact that pages are allocated in 2MB
units leading to -ENOMEM when establishing some configurations.
It's tagged for -stable as the problem was introduced with the
initial implementation in 4.5.
- The new "error status translation" routine, introduced with the 4.6
updates to the nfit driver, missed a necessary path in
acpi_nfit_ctl().
The end result is that we are falsely assuming commands complete
successfully when the embedded status says otherwise.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix translation of command status results
libnvdimm, pfn: fix memmap reservation sizing
Arnd Bergmann [Thu, 5 May 2016 23:22:39 +0000 (16:22 -0700)]
byteswap: try to avoid __builtin_constant_p gcc bug
This is another attempt to avoid a regression in wwn_to_u64() after that
started using get_unaligned_be64(), which in turn ran into a bug on
gcc-4.9 through 6.1.
The regression got introduced due to the combination of two separate
workarounds (commits e3bde9568d99: "include/linux/unaligned: force
inlining of byteswap operations" and ef3fb2422ffe: "scsi: fc: use
get/put_unaligned64 for wwn access") that each try to sidestep distinct
problems with gcc behavior (code growth and increased stack usage).
Unfortunately after both have been applied, a more serious gcc bug has
been uncovered, leading to incorrect object code that discards part of a
function and causes undefined behavior.
As part of this problem is how __builtin_constant_p gets evaluated on an
argument passed by reference into an inline function, this avoids the
use of __builtin_constant_p() for all architectures that set
CONFIG_ARCH_USE_BUILTIN_BSWAP. Most architectures do not set
ARCH_SUPPORTS_OPTIMIZED_INLINING, which means they probably do not
suffer from the problem in the qla2xxx driver, but they might still run
into it elsewhere.
Both of the original workarounds were only merged in the 4.6 kernel, and
the bug that is fixed by this patch should only appear if both are
there, so we probably don't need to backport the fix. On the other
hand, it works by simplifying the code path and should not have any
negative effects.
[arnd@arndb.de: fix older gcc warnings]
(http://lkml.kernel.org/r/12243652.bxSxEgjgfk@wuerfel) Link: https://lkml.org/lkml/headers/2016/4/12/1103 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=66122 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70232 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=70646 Fixes: e3bde9568d99 ("include/linux/unaligned: force inlining of byteswap operations") Fixes: ef3fb2422ffe ("scsi: fc: use get/put_unaligned64 for wwn access") Link: http://lkml.kernel.org/r/1780465.XdtPJpi8Tt@wuerfel Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Tested-by: Josh Poimboeuf <jpoimboe@redhat.com> # on gcc-5.3 Tested-by: Quinn Tran <quinn.tran@qlogic.com> Cc: Martin Jambor <mjambor@suse.cz> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: James Bottomley <James.Bottomley@hansenpartnership.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Thomas Graf <tgraf@suug.ch> Cc: Peter Zijlstra <peterz@infradead.org> Cc: David Rientjes <rientjes@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Jan Hubicka <hubicka@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Thu, 5 May 2016 23:22:35 +0000 (16:22 -0700)]
lib/stackdepot: avoid to return 0 handle
Recently, we allow to save the stacktrace whose hashed value is 0. It
causes the problem that stackdepot could return 0 even if in success.
User of stackdepot cannot distinguish whether it is success or not so we
need to solve this problem. In this patch, 1 bit are added to handle
and make valid handle none 0 by setting this bit. After that, valid
handle will not be 0 and 0 handle will represent failure correctly.
Fixes: 33334e25769c ("lib/stackdepot.c: allow the stack trace hash to be zero") Link: http://lkml.kernel.org/r/1462252403-1106-1-git-send-email-iamjoonsoo.kim@lge.com Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Zabel [Thu, 5 May 2016 23:22:29 +0000 (16:22 -0700)]
modpost: fix module autoloading for OF devices with generic compatible property
Since the wildcard at the end of OF module aliases is gone, autoloading
of modules that don't match a device's last (most generic) compatible
value fails.
For example the CODA960 VPU on i.MX6Q has the SoC specific compatible
"fsl,imx6q-vpu" and the generic compatible "cnm,coda960". Since the
driver currently only works with knowledge about the SoC specific
integration, it doesn't list "cnm,cod960" in the module device table.
This results in the device compatible
"of:NvpuT<NULL>Cfsl,imx6q-vpuCcnm,coda960" not matching the module alias
"of:N*T*Cfsl,imx6q-vpu" anymore, whereas before commit 2f632369ab79
("modpost: don't add a trailing wildcard for OF module aliases") it
matched the module alias "of:N*T*Cfsl,imx6q-vpu*".
This patch adds two module aliases for each compatible, one without the
wildcard and one with "C*" appended.
Mathias Krause [Thu, 5 May 2016 23:22:26 +0000 (16:22 -0700)]
proc: prevent accessing /proc/<PID>/environ until it's ready
If /proc/<PID>/environ gets read before the envp[] array is fully set up
in create_{aout,elf,elf_fdpic,flat}_tables(), we might end up trying to
read more bytes than are actually written, as env_start will already be
set but env_end will still be zero, making the range calculation
underflow, allowing to read beyond the end of what has been written.
Fix this as it is done for /proc/<PID>/cmdline by testing env_end for
zero. It is, apparently, intentionally set last in create_*_tables().
This bug was found by the PaX size_overflow plugin that detected the
arithmetic underflow of 'this_len = env_end - (env_start + src)' when
env_end is still zero.
The expected consequence is that userland trying to access
/proc/<PID>/environ of a not yet fully set up process may get
inconsistent data as we're in the middle of copying in the environment
variables.
Dan Streetman [Thu, 5 May 2016 23:22:23 +0000 (16:22 -0700)]
mm/zswap: provide unique zpool name
Instead of using "zswap" as the name for all zpools created, add an
atomic counter and use "zswap%x" with the counter number for each zpool
created, to provide a unique name for each new zpool.
As zsmalloc, one of the zpool implementations, requires/expects a unique
name for each pool created, zswap should provide a unique name. The
zsmalloc pool creation does not fail if a new pool with a conflicting
name is created, unless CONFIG_ZSMALLOC_STAT is enabled; in that case,
zsmalloc pool creation fails with -ENOMEM. Then zswap will be unable to
change its compressor parameter if its zpool is zsmalloc; it also will
be unable to change its zpool parameter back to zsmalloc, if it has any
existing old zpool using zsmalloc with page(s) in it. Attempts to
change the parameters will result in failure to create the zpool. This
changes zswap to provide a unique name for each zpool creation.
Fixes: f1c54846ee45 ("zswap: dynamic pool creation") Signed-off-by: Dan Streetman <ddstreet@ieee.org> Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Dan Streetman <dan.streetman@canonical.com> Cc: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: thp: kvm: fix memory corruption in KVM with THP enabled
After the THP refcounting change, obtaining a compound pages from
get_user_pages() no longer allows us to assume the entire compound page
is immediately mappable from a secondary MMU.
A secondary MMU doesn't want to call get_user_pages() more than once for
each compound page, in order to know if it can map the whole compound
page. So a secondary MMU needs to know from a single get_user_pages()
invocation when it can map immediately the entire compound page to avoid
a flood of unnecessary secondary MMU faults and spurious
atomic_inc()/atomic_dec() (pages don't have to be pinned by MMU notifier
users).
Ideally instead of the page->_mapcount < 1 check, get_user_pages()
should return the granularity of the "page" mapping in the "mm" passed
to get_user_pages(). However it's non trivial change to pass the "pmd"
status belonging to the "mm" walked by get_user_pages up the stack (up
to the caller of get_user_pages). So the fix just checks if there is
not a single pte mapping on the page returned by get_user_pages, and in
turn if the caller can assume that the whole compound page is mapped in
the current "mm" (in a pmd_trans_huge()). In such case the entire
compound page is safe to map into the secondary MMU without additional
get_user_pages() calls on the surrounding tail/head pages. In addition
of being faster, not having to run other get_user_pages() calls also
reduces the memory footprint of the secondary MMU fault in case the pmd
split happened as result of memory pressure.
Without this fix after a MADV_DONTNEED (like invoked by QEMU during
postcopy live migration or balloning) or after generic swapping (with a
failure in split_huge_page() that would only result in pmd splitting and
not a physical page split), KVM would map the whole compound page into
the shadow pagetables, despite regular faults or userfaults (like
UFFDIO_COPY) may map regular pages into the primary MMU as result of the
pte faults, leading to the guest mode and userland mode going out of
sync and not working on the same memory at all times.
Any other secondary MMU notifier manager (KVM is just one of the many
MMU notifier users) will need the same information if it doesn't want to
run a flood of get_user_pages_fast and it can support multiple
granularity in the secondary MMU mappings, so I think it is justified to
be exposed not just to KVM.
The other option would be to move transparent_hugepage_adjust to
mm/huge_memory.c but that currently has all kind of KVM data structures
in it, so it's definitely not a cut-and-paste work, so I couldn't do a
fix as cleaner as this one for 4.6.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: "Li, Liang Z" <liang.z.li@intel.com> Cc: Amit Shah <amit.shah@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 5 May 2016 23:22:15 +0000 (16:22 -0700)]
mm, cma: prevent nr_isolated_* counters from going negative
/proc/sys/vm/stat_refresh warns nr_isolated_anon and nr_isolated_file go
increasingly negative under compaction: which would add delay when
should be none, or no delay when should delay. The bug in compaction
was due to a recent mmotm patch, but much older instance of the bug was
also noticed in isolate_migratepages_range() which is used for CMA and
gigantic hugepage allocations.
The bug is caused by putback_movable_pages() in an error path
decrementing the isolated counters without them being previously
incremented by acct_isolated(). Fix isolate_migratepages_range() by
removing the error-path putback, thus reaching acct_isolated() with
migratepages still isolated, and leaving putback to caller like most
other places do.
Fixes: edc2ca612496 ("mm, compaction: move pageblock checks up from isolate_migratepages_range()")
[vbabka@suse.cz: expanded the changelog] Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason Baron [Thu, 5 May 2016 23:22:12 +0000 (16:22 -0700)]
mm: update min_free_kbytes from khugepaged after core initialization
Khugepaged attempts to raise min_free_kbytes if its set too low.
However, on boot khugepaged sets min_free_kbytes first from
subsys_initcall(), and then the mm 'core' over-rides min_free_kbytes
after from init_per_zone_wmark_min(), via a module_init() call.
Khugepaged used to use a late_initcall() to set min_free_kbytes (such
that it occurred after the core initialization), however this was
removed when the initialization of min_free_kbytes was integrated into
the starting of the khugepaged thread.
The fix here is simply to invoke the core initialization using a
core_initcall() instead of module_init(), such that the previous
initialization ordering is restored. I didn't restore the
late_initcall() since start_stop_khugepaged() already sets
min_free_kbytes via set_recommended_min_free_kbytes().
This was noticed when we had a number of page allocation failures when
moving a workload to a kernel with this new initialization ordering. On
an 8GB system this restores min_free_kbytes back to 67584 from 11365
when CONFIG_TRANSPARENT_HUGEPAGE=y is set and either
CONFIG_TRANSPARENT_HUGEPAGE_ALWAYS=y or
CONFIG_TRANSPARENT_HUGEPAGE_MADVISE=y.
Fixes: 79553da293d3 ("thp: cleanup khugepaged startup") Signed-off-by: Jason Baron <jbaron@akamai.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 5 May 2016 23:22:09 +0000 (16:22 -0700)]
huge pagecache: mmap_sem is unlocked when truncation splits pmd
zap_pmd_range()'s CONFIG_DEBUG_VM !rwsem_is_locked(&mmap_sem) BUG() will
be invalid with huge pagecache, in whatever way it is implemented:
truncation of a hugely-mapped file to an unhugely-aligned size would
easily hit it.
(Although anon THP could in principle apply khugepaged to private file
mappings, which are not excluded by the MADV_HUGEPAGE restrictions, in
practice there's a vm_ops check which excludes them, so it never hits
this BUG() - there's no interface to "truncate" an anonymous mapping.)
We could complicate the test, to check i_mmap_rwsem also when there's a
vm_file; but my inclination was to make zap_pmd_range() more readable by
simply deleting this check. A search has shown no report of the issue
in the years since commit e0897d75f0b2 ("mm, thp: print useful
information when mmap_sem is unlocked in zap_pmd_range") expanded it
from VM_BUG_ON() - though I cannot point to what commit I would say then
fixed the issue.
But there are a couple of other patches now floating around, neither yet
in the tree: let's agree to retain the check as a VM_BUG_ON_VMA(), as
Matthew Wilcox has done; but subject to a vma_is_anonymous() check, as
Kirill Shutemov has done. And let's get this in, without waiting for
any particular huge pagecache implementation to reach the tree.
Matthew said "We can reproduce this BUG() in the current Linus tree with
DAX PMDs".
Signed-off-by: Hugh Dickins <hughd@google.com> Tested-by: Matthew Wilcox <willy@linux.intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Yang Shi <yang.shi@linaro.org> Cc: Ning Qu <quning@gmail.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Andres Lagar-Cavilla <andreslc@google.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix problems in uapi definitions reported by Gabriel Laskar: (see
https://lkml.org/lkml/2016/4/5/205 for details)
- move public header file rio_mport_cdev.h to include/uapi/linux directory
- change types in data structures passed as IOCTL parameters
- improve parameter checking in some IOCTL service routines
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com> Reported-by: Gabriel Laskar <gabriel@lse.epita.fr> Tested-by: Barry Wood <barry.wood@idt.com> Cc: Gabriel Laskar <gabriel@lse.epita.fr> Cc: Matt Porter <mporter@kernel.crashing.org> Cc: Aurelien Jacquiot <a-jacquiot@ti.com> Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com> Cc: Barry Wood <barry.wood@idt.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 5 May 2016 23:22:03 +0000 (16:22 -0700)]
mm: memcontrol: let v2 cgroups follow changes in system swappiness
Cgroup2 currently doesn't have a per-cgroup swappiness setting. We
might want to add one later - that's a different discussion - but until
we do, the cgroups should always follow the system setting. Otherwise
it will be unchangeably set to whatever the ancestor inherited from the
system setting at the time of cgroup creation.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com> Cc: <stable@vger.kernel.org> [4.5] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 5 May 2016 22:40:38 +0000 (15:40 -0700)]
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic syscall fix from Arnd Bergmann:
"My last pull request for asm-generic had just one patch that added two
new system calls to asm/unistd.h, but unfortunately it turned out to
be wrong, pointing arch/tile compat mode at the native handlers rather
than the compat ones.
This was spotted by Yury Norov, who is working on ILP32 mode for
arch/arm64, which would have the same problem when merged. This fixes
the table to use the correct compat syscalls, like the other 64-bit
architectures do.
I'll try to find the time to come up with a solution that prevents
this problem from happening again, by allowing all future system calls
to just get added in a single file for use by all architectures"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: use compat version for preadv2 and pwritev2
Merge tag 'iio-fixes-for-4.6d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Fourth set of IIO fixes for the 4.6 cycle.
This last minute set is concerned with a regression in the mpu6050 driver.
The regression causes a null pointer dereference on any ACPI device
that has one of these present such as the ASUS T100TA Baytrail/T.
The issue was known but thought (i.e. missunderstood by me)
to only be a possible with no reports, so was routed via the normal merge
window. Turns out this was wrong (thanks to Alan for reporting the crash).
The pull is just for the null dereference fix and a followup fix
that also stops the reported name of the device being NULL.
* mpu6050
- Fix a 'possible' NULL dereference introduced as part of splitting the
driver to allow both i2c and spi to be supported. The issue affects ACPI
systems with this device.
- Fix a follow up issue where the name and chip id both get set to null if
the device driver instance is instantiated from ACPI tables.
Linus Torvalds [Thu, 5 May 2016 22:31:35 +0000 (15:31 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple last-minute fixes for ARM SoCs. Most of them are
for the OMAP platforms, the rest are all for different platforms.
OMAP:
All dts fixes, mostly affecting voltages and pinctrl for various
device drivers:
- Regulator minimum voltage fixes for omap5
- ISP syscon register offset fix for omap3
- Fix regulator initial modes for n900
- Fix omap5 pinctrl wkup instance size
Allwinner:
Remove incorrect constraints from a dcdc1 regulator
Alltera SoCFPGA:
Fix compilation in thumb2 mode
Samsung exynos:
Fix a potential oops in the pm-domain error handling
Davinci:
Avoid a link error if NVMEM is disabled
Renesas:
Do not mark an external uart clock as disabled, to allow probing
the uarts"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: davinci: only use NVMEM when available
ARM: SoCFPGA: Fix secondary CPU startup in thumb2 kernel
ARM: dts: omap5: fix range of permitted wakeup pinmux registers
ARM: dts: omap3-n900: Specify peripherals LDO regulators initial mode
ARM: dts: omap3: Fix ISP syscon register offset
ARM: dts: omap5-cm-t54: fix ldo1_reg and ldo4_reg ranges
ARM: dts: omap5-board-common: fix ldo1_reg and ldo4_reg ranges
arm64: dts: r8a7795: Don't disable referenced optional scif clock
ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator
Howard Cochran [Thu, 10 Mar 2016 06:12:39 +0000 (01:12 -0500)]
writeback: Fix performance regression in wb_over_bg_thresh()
Commit 947e9762a8dd ("writeback: update wb_over_bg_thresh() to use
wb_domain aware operations") unintentionally changed this function's
meaning from "are there more dirty pages than the background writeback
threshold" to "are there more dirty pages than the writeback threshold".
The background writeback threshold is typically half of the writeback
threshold, so this had the effect of raising the number of dirty pages
required to cause a writeback worker to perform background writeout.
This can cause a very severe performance regression when a BDI uses
BDI_CAP_STRICTLIMIT because balance_dirty_pages() and the writeback worker
can now disagree on whether writeback should be initiated.
For example, in a system having 1GB of RAM, a single spinning disk, and a
"pass-through" FUSE filesystem mounted over the disk, application code
mmapped a 128MB file on the disk and was randomly dirtying pages in that
mapping.
Because FUSE uses strictlimit and has a default max_ratio of only 1%, in
balance_dirty_pages, thresh is ~200, bg_thresh is ~100, and the
dirty_freerun_ceiling is the average of those, ~150. So, it pauses the
dirtying processes when we have 151 dirty pages and wakes up a background
writeback worker. But the worker tests the wrong threshold (200 instead of
100), so it does not initiate writeback and just returns.
Thus, balance_dirty_pages keeps looping, sleeping and then waking up the
worker who will do nothing. It remains stuck in this state until the few
dirty pages that we have finally expire and we write them back for that
reason. Then the whole process repeats, resulting in near-zero throughput
through the FUSE BDI.
The fix is to call the parameterized variant of wb_calc_thresh, so that the
worker will do writeback if the bg_thresh is exceeded which was the
behavior before the referenced commit.
Vladimir Murzin [Wed, 4 May 2016 09:39:02 +0000 (10:39 +0100)]
ARM: 8573/1: domain: move {set,get}_domain under config guard
Recursive undefined instrcution falut is seen with R-class taking an
exception. The reson for that is __show_regs() tries to get domain
information, but domains is not available on !MMU cores, like R/M
class.
Fix it by puting {set,get}_domain functions under CONFIG_CPU_CP15_MMU
guard and providing stubs for the case where domains is not supported.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 8572/1: nommu: change memory reserve for the vectors
Commit 19accfd3 (ARM: move vector stubs) moved the vector stubs in an
additional page above the base vector one. This change wasn't taken into
account by the nommu memreserve.
This patch ensures that the kernel won't overwrite any vector stub on
nommu.
[changed the MPU side too]
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) broke the support for
MPU on ARMv7-R. This patch adapts the code inside CONFIG_ARM_MPU to use
memblocks appropriately.
MPU initialisation only uses the first memory region, and removes all
subsequent ones. Because looping over all regions that need removal is
inefficient, and memblock_remove already handles memory ranges, we can
flatten the 'for_each_memblock' part.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iSER currently has a couple places that set max_sectors in either the host
template or SCSI host, and all of them get it wrong.
This patch instead uses a single assignment that (hopefully) gets it right:
the max_sectors value must be derived from the number of segments in the
FR or FMR structure, but actually be one lower than the page size multiplied
by the number of sectors, as it has to handle the case of non-aligned I/O.
Without this I get trivial to reproduce hangs when running xfstests
(on XFS) over iSER to Linux targets.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Acked-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Doug Ledford <dledford@redhat.com>
This oops happens with the namespace_sem held and can be triggered by
non-root users. An all around not pleasant experience.
To avoid this scenario when finding the appropriate source mount to
copy stop the walk up the mnt_master chain when the first source mount
is encountered.
Further rewrite the walk up the last_source mnt_master chain so that
it is clear what is going on.
The reason why the first source mount is special is that it it's
mnt_parent is not a mount in the dest_mnt propagation tree, and as
such termination conditions based up on the dest_mnt mount propgation
tree do not make sense.
To avoid other kinds of confusion last_dest is not changed when
computing last_source. last_dest is only used once in propagate_one
and that is above the point of the code being modified, so changing
the global variable is meaningless and confusing.
Wang YanQing [Thu, 5 May 2016 13:14:21 +0000 (14:14 +0100)]
x86/sysfb_efi: Fix valid BAR address range check
The code for checking whether a BAR address range is valid will break
out of the loop when a start address of 0x0 is encountered.
This behaviour is wrong since by breaking out of the loop we may miss
the BAR that describes the EFI frame buffer in a later iteration.
Because of this bug I can't use video=efifb: boot parameter to get
efifb on my new ThinkPad E550 for my old linux system hard disk with
3.10 kernel. In 3.10, efifb is the only choice due to DRM/I915 not
supporting the GPU.
This patch also add a trivial optimization to break out after we find
the frame buffer address range without testing later BARs.
Signed-off-by: Wang YanQing <udknight@gmail.com>
[ Rewrote changelog. ] Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Peter Jones <pjones@redhat.com> Cc: <stable@vger.kernel.org> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/1462454061-21561-2-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org>
Initial HIGHMEM support on ARC was introduced for PAE40 where the low
memory (0x8000_0000 based) and high memory (0x1_0000_0000) were
physically contiguous. So CONFIG_FLATMEM sufficed (despite a peipheral
hole in the middle, which wasted a bit of struct page memory, but things
worked).
However w/o PAE, highmem was not possible and we could only reach
~1.75GB of DDR. Now there is a use case to access ~4GB of DDR w/o PAE40
The idea is to have low memory at canonical 0x8000_0000 and highmem
at 0 so enire 4GB address space is available for physical addressing
This needs additional platform/interconnect mapping to convert
the non contiguous physical addresses into linear bus adresses.
From Linux point of view, non contiguous divide means FLATMEM no
longer works and DISCONTIGMEM is needed to track the pfns in the 2
regions.
This scheme would also work for PAE40, only better in that we don't
waste struct page memory for the peripheral hole.
Vineet Gupta [Thu, 5 May 2016 09:23:48 +0000 (14:53 +0530)]
ARC: Fix PAE40 boot failures due to PTE truncation
So a benign looking cleanup which macro'ized PAGE_SHIFT shifts turned
out to be bad (since it was done non-sensically across the board).
It caused boot failures with PAE40 as forced cast to (unsigned long)
from newly introduced virt_to_pfn() was causing truncatiion of the
(long long) pte/paddr values.
It is OK to use this in accessors dealing with kernel virtual address,
pointers etc, but not for PTE values themelves.
Fixes: cJ2ff5cf2735c ("ARC: mm: Use virt_to_pfn() for addr >> PAGE_SHIFT pattern) Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Thu, 5 May 2016 08:02:34 +0000 (13:32 +0530)]
ARC: Add missing io barriers to io{read,write}{16,32}be()
While reviewing a different change to asm-generic/io.h Arnd spotted that
ARC ioread32 and ioread32be both of which come from asm-generic versions
are not symmetrical in terms of calling the io barriers.
exposed some issues with the fact that we were relying on the EFI memory
mapping mechanisms to map in our MMRs for us, after commit d394f2d9d8e1.
Rather than revert the entire commit and go back to forcing
EFI_OLD_MEMMAP on all UVs, we're going to add the call to map_low_mmrs()
back into uv_system_init(), and then fix up our EFI runtime calls to use
the appropriate page table.
For now, UV2+ will still need efi=old_map to boot, but there will be
other changes soon that should eliminate the need for this.
Signed-off-by: Alex Thorlton <athorlton@sgi.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Len Brown <len.brown@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Russ Anderson <rja@sgi.com> Cc: Dimitri Sivanich <sivanich@sgi.com> Link: http://lkml.kernel.org/r/1462401592-120735-1-git-send-email-athorlton@sgi.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Thu, 5 May 2016 02:12:09 +0000 (12:12 +1000)]
Merge tag 'drm-intel-fixes-2016-05-02' of git://anongit.freedesktop.org/drm-intel into drm-fixes
i915 fixes for 4.6. A bit more than I'd like at this stage, but
OTOH they're all stable material.
* tag 'drm-intel-fixes-2016-05-02' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
drm/i915: Fake HDMI live status
drm/i915: Fix eDP low vswing for Broadwell
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
drm/i915: Fix system resume if PCI device remained enabled
drm/i915: Avoid stalling on pending flips for legacy cursor updates
Dave Airlie [Thu, 5 May 2016 00:37:25 +0000 (10:37 +1000)]
Merge branch 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
two fixes for hw lockups and one for a double free
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: make sure vertical front porch is at least 1
drm/radeon: make sure vertical front porch is at least 1
drm/amdgpu: set metadata pointer to NULL after freeing.
If of_node is set before calling platform_device_add, the driver core
will try to use of: modalias matching, which fails because the device
tree nodes don't have a compatible property set. This patch fixes
imx-ipuv3-crtc module autoloading by setting the of_node property only
after the platform modalias is set.
Fixes: 304e6be652e2 ("gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports") Reported-by: Dennis Gilmore <dennis@ausil.us> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-By: Dennis Gilmore <dennis@ausil.us> Cc: stable@vger.kernel.org # 4.4+ Signed-off-by: Dave Airlie <airlied@redhat.com>
Viresh Kumar [Wed, 4 May 2016 13:19:55 +0000 (18:49 +0530)]
PM / OPP: Remove useless check
Regulators are optional for devices using OPPs and the OPP core
shouldn't be printing any errors for such missing regulators.
It was fine before the commit 0c717d0f9cb4, but that failed to update
this part of the code to remove an 'always true' check and an extra
unwanted print message.
Fix that now.
Fixes: 0c717d0f9cb4 (PM / OPP: Initialize regulator pointer to an error value) Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Yury Norov [Mon, 2 May 2016 16:12:47 +0000 (19:12 +0300)]
asm-generic: use compat version for preadv2 and pwritev2
Compat architectures that does not use generic unistd (mips, s390),
declare compat version in their syscall tables for preadv2 and
pwritev2. Generic unistd syscall table should do it as well.
[arnd: this initially slipped through the review and an
incorrect patch got merged. arch/tile/ is the only architecture
that could be affected for their 32-bit compat mode, every
other architecture we support today is fine.]
Set the mutex owner thread ID.
Original patch from: Prarit Bhargava <prarit@redhat.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=115121 Link: https://github.com/acpica/acpica/commit/7a3bd2d9 Signed-off-by: Prarit Bhargava <prarit@redhat.com> Tested-by: Andy Lutomirski <luto@kernel.org> # On a Dell XPS 13 9350 Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 4 May 2016 18:14:00 +0000 (11:14 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull IMA fix from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: fix the string representation of the LSM/IMA hook enumeration ordering
Linus Torvalds [Wed, 4 May 2016 18:00:05 +0000 (11:00 -0700)]
Merge tag 'for-linus-4.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen regression fixes from David Vrabel:
- Fix two regressions causing crashes in 32-bit PV guests
- Fix a regression in the evtchn driver
* tag 'for-linus-4.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: fix ring resize when binding new events
xen/balloon: Fix crash when ballooning on x86 32 bit PAE
xen: Fix page <-> pfn conversion on 32 bit systems
Jan Beulich [Wed, 4 May 2016 13:02:36 +0000 (07:02 -0600)]
xen/evtchn: fix ring resize when binding new events
The copying of ring data was wrong for two cases: For a full ring
nothing got copied at all (as in that case the canonicalized producer
and consumer indexes are identical). And in case one or both of the
canonicalized (after the resize) indexes would point into the second
half of the buffer, the copied data ended up in the wrong (free) part
of the new buffer. In both cases uninitialized data would get passed
back to the caller.
Fix this by simply copying the old ring contents twice: Once to the
low half of the new buffer, and a second time to the high half.
This addresses the inability to boot a HVM guest with 64 or more
vCPUs. This regression was caused by 8620015499101090 (xen/evtchn:
dynamically grow pending event channel ring).
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: <stable@vger.kernel.org> # 4.4+ Signed-off-by: David Vrabel <david.vrabel@citrix.com>
After commit 8fa520af5081 "intel_pstate: Remove freq calculation from
intel_pstate_calc_busy()" intel_pstate_get() calls get_avg_frequency()
to compute the average frequency, which is problematic for two reasons.
First, intel_pstate_get() may be invoked before the driver reads the
CPU feedback registers for the first time and if that happens,
get_avg_frequency() will attempt to divide by zero.
Second, the get_avg_frequency() call in intel_pstate_get() is racy
with respect to intel_pstate_sample() and it may end up returning
completely meaningless values for this reason.
Moreover, after commit 7349ec0470b6 "intel_pstate: Move
intel_pstate_calc_busy() into get_target_pstate_use_performance()"
sample.core_pct_busy is never computed on Atom, but it is used in
intel_pstate_adjust_busy_pstate() in that case too.
To address those problems notice that if sample.core_pct_busy
was used in the average frequency computation carried out by
get_avg_frequency(), both the divide by zero problem and the
race with respect to intel_pstate_sample() would be avoided.
Accordingly, move the invocation of intel_pstate_calc_busy() from
get_target_pstate_use_performance() to intel_pstate_update_util(),
which also will take care of the uninitialized sample.core_pct_busy
on Atom, and modify get_avg_frequency() to use sample.core_pct_busy
as per the above.
Reported-by: kernel test robot <ying.huang@linux.intel.com> Link: http://marc.info/?l=linux-kernel&m=146226437623173&w=4 Fixes: 8fa520af5081 "intel_pstate: Remove freq calculation from intel_pstate_calc_busy()" Fixes: 7349ec0470b6 "intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()" Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
projects / mirror_ubuntu-kernels.git / log