Davide Caratti [Wed, 7 Nov 2018 10:28:18 +0000 (11:28 +0100)]
net: vlan: add support for tunnel offload
GSO tunneled packets are always segmented in software before they are
transmitted by a VLAN, even when the lower device can offload tunnel
encapsulation and VLAN together (i.e., some bits in NETIF_F_GSO_ENCAP_ALL
mask are set in the lower device 'vlan_features'). If we let VLANs have
the same tunnel offload capabilities as their lower device, throughput
can improve significantly when CPU is limited on the transmitter side.
- set NETIF_F_GSO_ENCAP_ALL bits in the VLAN 'hw_features', to ensure
that 'features' will have those bits zeroed only when the lower device
has no hardware support for tunnel encapsulation.
- for the same reason, copy GSO-related bits of 'hw_enc_features' from
lower device to VLAN, and ensure to update that value when the lower
device changes its features.
- set NETIF_F_HW_CSUM bit in the VLAN 'hw_enc_features' if 'real_dev'
is able to compute checksums at least for a kind of packets, like done
with commit 8403debeead8 ("vlan: Keep NETIF_F_HW_CSUM similar to other
software devices"). This avoids software segmentation due to mismatching
checksum capabilities between VLAN's 'features' and 'hw_enc_features'.
Reported-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 09:34:36 +0000 (10:34 +0100)]
tun: compute the RFS hash only if needed.
The tun XDP sendmsg code path, unconditionally computes the symmetric
hash of each packet for RFS's sake, even when we could skip it. e.g.
when the device has a single queue.
This change adds the check already in-place for the skb sendmsg path
to avoid unneeded hashing.
The above gives small, but measurable, performance gain for VM xmit
path when zerocopy is not enabled.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 7 Nov 2018 07:52:46 +0000 (08:52 +0100)]
net: phy: realtek: load driver for all PHYs with a Realtek OUI
Instead of listing every single PHYID, load the driver for every PHYID
with a Realtek OUI, independent of model number and revision.
This patch also improves two further aspects:
- constify realtek_tbl[]
- the mask should have been 0xffffffff instead of 0x001fffff so far,
by masking out some bits a PHY from another vendor could have been
matched
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ae7a5aff783c ("net: dsa: bcm_sf2: Keep copy of inserted rules") CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Chen [Wed, 7 Nov 2018 00:37:44 +0000 (16:37 -0800)]
net: phy: bcm7xxx: Add entry for BCM7255
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Nov 2018 00:23:05 +0000 (16:23 -0800)]
Merge branch 'udp-gro'
Paolo Abeni says:
====================
udp: implement GRO support
This series implements GRO support for UDP sockets, as the RX counterpart
of commit bec1f6f69736 ("udp: generate gso with UDP_SEGMENT").
The core functionality is implemented by the second patch, introducing a new
sockopt to enable UDP_GRO, while patch 3 implements support for passing the
segment size to the user space via a new cmsg.
UDP GRO performs a socket lookup for each ingress packets and aggregate datagram
directed to UDP GRO enabled sockets with constant l4 tuple.
UDP GRO packets can land on non GRO-enabled sockets, e.g. due to iptables NAT
rules, and that could potentially confuse existing applications.
The solution adopted here is to de-segment the GRO packet before enqueuing
as needed. Since we must cope with packet reinsertion after de-segmentation,
the relevant code is factored-out in ipv4 and ipv6 specific helpers and exposed
to UDP usage.
While the current code can probably be improved, this safeguard ,implemented in
the patches 4-7, allows future enachements to enable UDP GSO offload on more
virtual devices eventually even on forwarded packets.
The last 4 for patches implement some performance and functional self-tests,
re-using the existing udpgso infrastructure. The problematic scenario described
above is explicitly tested.
This revision of the series try to address the feedback provided by Willem and
Subash on previous iteration.
====================
Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 11:38:37 +0000 (12:38 +0100)]
selftests: add functionals test for UDP GRO
Extends the existing udp programs to allow checking for proper
GRO aggregation/GSO size, and run the tests via a shell script, using
a veth pair with XDP program attached to trigger the GRO code path.
rfc v3 -> v1:
- use ip route to attach the xdp helper to the veth
rfc v2 -> rfc v3:
- add missing test program options documentation
- fix sporatic test failures (receiver faster than sender)
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 11:38:35 +0000 (12:38 +0100)]
selftests: add dummy xdp test helper
This trivial XDP program does nothing, but will be used by the
next patch to test the GRO path in a net namespace, leveraging
the veth XDP implementation.
It's added here, despite its 'net' usage, to avoid the duplication
of the llc-related makefile boilerplate.
rfc v3 -> v1:
- move the helper implementation into the bpf directory, don't
touch udpgso_bench_rx
rfc v2 -> rfc v3:
- move 'x' option handling here
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 11:38:33 +0000 (12:38 +0100)]
udp: cope with UDP GRO packet misdirection
In some scenarios, the GRO engine can assemble an UDP GRO packet
that ultimately lands on a non GRO-enabled socket.
This patch tries to address the issue explicitly checking for the UDP
socket features before enqueuing the packet, and eventually segmenting
the unexpected GRO packet, as needed.
We must also cope with re-insertion requests: after segmentation the
UDP code calls the helper introduced by the previous patches, as needed.
Segmentation is performed by a common helper, which takes care of
updating socket and protocol stats is case of failure.
rfc v3 -> v1
- fix compile issues with rxrpc
- when gso_segment returns NULL, treat is as an error
- added 'ipv4' argument to udp_rcv_segment()
rfc v2 -> rfc v3
- moved udp_rcv_segment() into net/udp.h, account errors to socket
and ns, always return NULL or segs list
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 11:38:29 +0000 (12:38 +0100)]
udp: implement GRO for plain UDP sockets.
This is the RX counterpart of commit bec1f6f69736 ("udp: generate gso
with UDP_SEGMENT"). When UDP_GRO is enabled, such socket is also
eligible for GRO in the rx path: UDP segments directed to such socket
are assembled into a larger GSO_UDP_L4 packet.
The core UDP GRO support is enabled with setsockopt(UDP_GRO).
Initial benchmark numbers:
Before:
udp rx: 1079 MB/s 769065 calls/s
After:
udp rx: 1466 MB/s 24877 calls/s
This change introduces a side effect in respect to UDP tunnels:
after a UDP tunnel creation, now the kernel performs a lookup per ingress
UDP packet, while before such lookup happened only if the ingress packet
carried a valid internal header csum.
rfc v2 -> rfc v3:
- fixed typos in macro name and comments
- really enforce UDP_GRO_CNT_MAX, instead of UDP_GRO_CNT_MAX + 1
- acquire socket lock in UDP_GRO setsockopt
rfc v1 -> rfc v2:
- use a new option to enable UDP GRO
- use static keys to protect the UDP GRO socket lookup
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 7 Nov 2018 11:38:28 +0000 (12:38 +0100)]
udp: implement complete book-keeping for encap_needed
The *encap_needed static keys are enabled by UDP tunnels
and several UDP encapsulations type, but they are never
turned off. This can cause unneeded overall performance
degradation for systems where such features are used
transiently.
This patch introduces complete book-keeping for such keys,
decreasing the usage at socket destruction time, if needed,
and avoiding that the same socket could increase the key
usage multiple times.
rfc v3 -> v1:
- add socket lock around udp_tunnel_encap_enable()
rfc v2 -> rfc v3:
- use udp_tunnel_encap_enable() in setsockopt()
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
vrf: allow simultaneous service instances in default and other VRFs
Services currently have to be VRF-aware if they are using an unbound
socket. One cannot have multiple service instances running in the
default and other VRFs for services that are not VRF-aware and listen
on an unbound socket. This is because there is no easy way of isolating
packets received in the default VRF from those arriving in other VRFs.
This series provides this isolation for stream sockets subject to the
existing kernel parameter net.ipv4.tcp_l3mdev_accept not being set,
given that this is documented as allowing a single service instance to
work across all VRF domains. Similarly, net.ipv4.udp_l3mdev_accept is
checked for datagram sockets, and net.ipv4.raw_l3mdev_accept is
introduced for raw sockets. The functionality applies to UDP & TCP
services as well as those using raw sockets, and is for IPv4 and IPv6.
Example of running ssh instances in default and blue VRF:
v1:
- Address Paolo Abeni's comments (patch 4/5)
- Fix build when CONFIG_NET_L3_MASTER_DEV not defined (patch 1/5)
v2:
- Address David Aherns' comments (patches 4/5 and 5/5)
- Remove patches 3/5 and 5/5 from series for individual submissions
- Include a sysctl for raw sockets as recommended by David Ahern
- Expand series into 10 patches and provide improved descriptions
v3:
- Update description for patch 1/10 and remove patch 6/10
v4:
- Set default to enabled for raw socket sysctl as recommended by David Ahern
v5:
- Address review comments from David Ahern in patches 2-5
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dewi Morgan [Wed, 7 Nov 2018 15:36:10 +0000 (15:36 +0000)]
ipv6: do not drop vrf udp multicast packets
For bound udp sockets in a vrf, also check the sdif to get the index
for ingress devices enslaved to an l3mdev.
Signed-off-by: Dewi Morgan <morgand@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:09 +0000 (15:36 +0000)]
ipv6: handling of multicast packets received in VRF
If the skb for multicast packets marked as enslaved to a VRF are
received, then the secondary device index should be used to obtain
the real device. And verify the multicast address against the
enslaved rather than the l3mdev device.
Signed-off-by: Dewi Morgan <morgand@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:08 +0000 (15:36 +0000)]
ipv6: allow ping to link-local address in VRF
If link-local packets are marked as enslaved to a VRF, then to allow
ping to the link-local from a vrf, the error handling for IPV6_PKTINFO
needs to be relaxed to also allow the pkt ipi6_ifindex to be that of a
slave device to the vrf.
Note that the real device also needs to be retrieved in icmp6_iif()
to set the ipv6 flow oif to this for icmp echo reply handling. The
recent commit 24b711edfc34 ("net/ipv6: Fix linklocal to global address
with VRF") takes care of this, so the sdif does not need checking here.
This fix makes ping to link-local consistent with that to global
addresses, in that this can now be done from within the same VRF that
the address is in.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:07 +0000 (15:36 +0000)]
vrf: mark skb for multicast or link-local as enslaved to VRF
The skb for packets that are multicast or to a link-local address are
not marked as being enslaved to a VRF, if they are received on a socket
bound to the VRF. This is needed for ND and it is preferable for the
kernel not to have to deal with the additional use-cases if ll or mcast
packets are handled as enslaved. However, this does not allow service
instances listening on unbound and bound to VRF sockets to distinguish
the VRF used, if packets are sent as multicast or to a link-local
address. The fix is for the VRF driver to also mark these skb as being
enslaved to the VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Duncan Eastoe [Wed, 7 Nov 2018 15:36:06 +0000 (15:36 +0000)]
net: fix raw socket lookup device bind matching with VRFs
When there exist a pair of raw sockets one unbound and one bound
to a VRF but equal in all other respects, when a packet is received
in the VRF context, __raw_v4_lookup() matches on both sockets.
This results in the packet being delivered over both sockets,
instead of only the raw socket bound to the VRF. The bound device
checks in __raw_v4_lookup() are replaced with a call to
raw_sk_bound_dev_eq() which correctly handles whether the packet
should be delivered over the unbound socket in such cases.
In __raw_v6_lookup() the match on the device binding of the socket is
similarly updated to use raw_sk_bound_dev_eq() which matches the
handling in __raw_v4_lookup().
Importantly raw_sk_bound_dev_eq() takes the raw_l3mdev_accept sysctl
into account.
Signed-off-by: Duncan Eastoe <deastoe@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:05 +0000 (15:36 +0000)]
net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs
Add a sysctl raw_l3mdev_accept to control raw socket lookup in a manner
similar to use of tcp_l3mdev_accept for stream and of udp_l3mdev_accept
for datagram sockets. Have this default to enabled for reasons of
backwards compatibility. This is so as to specify the output device
with cmsg and IP_PKTINFO, but using a socket not bound to the
corresponding VRF. This allows e.g. older ping implementations to be
run with specifying the device but without executing it in the VRF.
If the option is disabled, packets received in a VRF context are only
handled by a raw socket bound to the VRF, and correspondingly packets
in the default VRF are only handled by a socket not bound to any VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:04 +0000 (15:36 +0000)]
net: ensure unbound datagram socket to be chosen when not in a VRF
Ensure an unbound datagram skt is chosen when not in a VRF. The check
for a device match in compute_score() for UDP must be performed when
there is no device match. For this, a failure is returned when there is
no device match. This ensures that bound sockets are never selected,
even if there is no unbound socket.
Allow IPv6 packets to be sent over a datagram skt bound to a VRF. These
packets are currently blocked, as flowi6_oif was set to that of the
master vrf device, and the ipi6_ifindex is that of the slave device.
Allow these packets to be sent by checking the device with ipi6_ifindex
has the same L3 scope as that of the bound device of the skt, which is
the master vrf device. Note that this check always succeeds if the skt
is unbound.
Even though the right datagram skt is now selected by compute_score(),
a different skt is being returned that is bound to the wrong vrf. The
difference between these and stream sockets is the handling of the skt
option for SO_REUSEPORT. While the handling when adding a skt for reuse
correctly checks that the bound device of the skt is a match, the skts
in the hashslot are already incorrect. So for the same hash, a skt for
the wrong vrf may be selected for the required port. The root cause is
that the skt is immediately placed into a slot when it is created,
but when the skt is then bound using SO_BINDTODEVICE, it remains in the
same slot. The solution is to move the skt to the correct slot by
forcing a rehash.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Wed, 7 Nov 2018 15:36:03 +0000 (15:36 +0000)]
net: ensure unbound stream socket to be chosen when not in a VRF
The commit a04a480d4392 ("net: Require exact match for TCP socket
lookups if dif is l3mdev") only ensures that the correct socket is
selected for packets in a VRF. However, there is no guarantee that
the unbound socket will be selected for packets when not in a VRF.
By checking for a device match in compute_score() also for the case
when there is no bound device and attaching a score to this, the
unbound socket is selected. And if a failure is returned when there
is no device match, this ensures that bound sockets are never selected,
even if there is no unbound socket.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Wed, 7 Nov 2018 15:36:02 +0000 (15:36 +0000)]
net: allow binding socket in a VRF when there's an unbound socket
Change the inet socket lookup to avoid packets arriving on a device
enslaved to an l3mdev from matching unbound sockets by removing the
wildcard for non sk_bound_dev_if and instead relying on check against
the secondary device index, which will be 0 when the input device is
not enslaved to an l3mdev and so match against an unbound socket and
not match when the input device is enslaved.
Change the socket binding to take the l3mdev into account to allow an
unbound socket to not conflict sockets bound to an l3mdev given the
datapath isolation now guaranteed.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 7 Nov 2018 02:33:53 +0000 (02:33 +0000)]
net: hns3: Remove set but not used variable 'reset_level'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c: In function 'hclge_log_and_clear_ppp_error':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_err.c:821:24: warning:
variable 'reset_level' set but not used [-Wunused-but-set-variable]
enum hnae3_reset_type reset_level = HNAE3_NONE_RESET;
It never used since introduction in commit 01865a50d78f ("net: hns3: Add enable and process hw errors of TM scheduler")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nfp: more set actions and notifier refactor
This series brings updates to flower offload code. First Pieter adds
support for setting TTL, ToS, Flow Label and Hop Limit fields in IPv4
and IPv6 headers.
Remaining 5 patches deal with factoring out netdev notifiers from flower
code. We already have two instances, and more is coming, so it's time
to move to one central notifier which then feeds individual feature
handlers.
I start that part by cleaning up the existing notifiers. Next a central
notifier is added, and used by flower offloads.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 7 Nov 2018 01:07:34 +0000 (17:07 -0800)]
nfp: flower: use the common netdev notifier
Use driver's common notifier for LAG and tunnel configuration.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 7 Nov 2018 01:07:33 +0000 (17:07 -0800)]
nfp: register a notifier handler in a central location for the device
Code interested in networking events registers its own notifier
handlers. Create one device-wide notifier instance.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 7 Nov 2018 01:07:32 +0000 (17:07 -0800)]
nfp: flower: make nfp_fl_lag_changels_event() void
nfp_fl_lag_changels_event() never fails, and therefore we would
never return NOTIFY_BAD for NETDEV_CHANGELOWERSTATE. Make this
clearer by changing nfp_fl_lag_changels_event()'s return type
to void.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 7 Nov 2018 01:07:31 +0000 (17:07 -0800)]
nfp: flower: don't try to nack device unregister events
Returning an error from a notifier means we want to veto the change.
We shouldn't veto NETDEV_UNREGISTER just because we couldn't find
the tracking info for given master.
I can't seem to find a way to trigger this unless we have some
other bug, so it's probably not fix-worthy.
While at it move the checking if the netdev really is of interest
into the handling functions, like we do for other events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 7 Nov 2018 01:07:30 +0000 (17:07 -0800)]
nfp: flower: remove unnecessary iteration over devices
For flower tunnel offloads FW has to be informed about MAC addresses
of tunnel devices. We use a netdev notifier to keep track of these
addresses.
Remove unnecessary loop over netdevices after notifier is registered.
The intention of the loop was to catch devices which already existed
on the system before nfp driver got loaded, but netdev notifier will
replay NETDEV_REGISTER events.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: add ipv6 set flow label and hop limit offload
Add ipv6 set flow label and hop limit action offload. Since pedit sets
headers per 4 byte word, we need to ensure that setting either version,
priority, payload_len or nexthdr does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv4 set ttl and tos action offload. Since pedit sets headers per 4
byte word, we need to ensure that setting either version, ihl, protocol,
total length or checksum does not get offloaded.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:18 +0000 (12:06 +0800)]
net: hns3: fix for cmd queue memory not freed problem during reset
It is not necessary to reallocate the descriptor and remap the
descriptor memory in reset process, otherwise it may cause memory
not freed problem.
Also, this patch initializes the cmd queue's spinlocks in
hclgevf_alloc_cmd_queue, and take the spinlocks when reinitializing
cmd queue' registers.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:17 +0000 (12:06 +0800)]
net: hns3: add error handler for hclge_reset()
When hclge_reset() is called, it may fail for several reasons.
For example, an higher-level reset event occurs, memory allocation
failure, hardware reset timeout, etc. Therefore, it is necessary
to add corresponding error handling for these situations.
1. A high-level reset is required due to a high-level reset failure.
2. For memory allocation failure, a high-level reset is initiated by
the timer to recover. The reason for using the timer is to prevent this
new high-level reset to interrupt the reset process of other pf/vf;
3. For the case of hardware reset timeout, reschedule the reset task
to wait for the hardware to complete the reset.
For memory allocation failure and reset timeouts, in order to prevent
an infinite number of scheduled reset tasks, the number of error
recovery needs to be limited.
This patch also add some reset related debug log printing.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:16 +0000 (12:06 +0800)]
net: hns3: call roce's reset notify callback when resetting
While doing resetting, roce should do its uninitailization part
before nic's, and do its initialization part after nic's.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:15 +0000 (12:06 +0800)]
net: hns3: adjust the process of PF reset
When doing PF reset, the driver needs to do some preparatory work
before asserting PF reset. Since when hardware is resetting, it
is necessary to stop tx/rx queue, clear hardware table, etc,
otherwise hardware may run into unrecoverable state if there is
still IO running when the hardware is resetting.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:14 +0000 (12:06 +0800)]
net: hns3: move some reset information from hnae3_handle into hclge_dev/hclgevf_dev
Saving reset related information in the hclge_dev/hclgevf_dev
structure is more suitable than the hnae3_handle, since hardware
related information is kept in these two structure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:13 +0000 (12:06 +0800)]
net: hns3: ignore new coming low-level reset while doing high-level reset
When processing a higher level reset, the pending lower level reset
does not have to be processed anymore, because the higher level
reset is the superset of the lower level reset.
Therefore, when processing an higher level reset, the request of
lower level reset needs to be cleared.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:12 +0000 (12:06 +0800)]
net: hns3: use HNS3_NIC_STATE_RESETTING to indicate resetting
While hclge is going to reset, it will notify its client with
HNAE3_DOWN_CLIENT, so this client should get into a resetting
status from this moment, other operations from the stack need to
be blocked as well. And when the reset is finished, the client
will be notified with HNAE3_UP_CLIENT, so this is the end of
the resetting status.
This patch uses HNS3_NIC_STATE_RESETTING flag to implement that,
and adds hns3_nic_resetting() to indicate which operation is not
allowed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:11 +0000 (12:06 +0800)]
net: hns3: enable/disable ring in the enet while doing UP/DOWN
While hardware gets into reset status, the firmware will not respond to
driver's command request, which may cause ring not disabled problem
during reset process.
So this patch uses register instead of command to enable/disable the ring
in the enet while doing UP/DOWN operation.
Also, HNS3_RING_RX_VM_REG is previously unused, so change it to the
correct meaning, and add a wrapper function for readl().
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:10 +0000 (12:06 +0800)]
net: hns3: adjust the location of clearing the table when doing reset
When doing a function reset, the hardware table should be cleared
before the hardware reset. In current code, this clearing is done
in hns3_reset_notify_uninit_enet, but it is too late, because
the hardware reset is already done, hns3_reset_notify_down_enet
is more suitable to do that.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:09 +0000 (12:06 +0800)]
net: hns3: provide some interface & information for the client
The client needs to know if the hardware is resetting when
loading or unloading itself, because client may abort the loading
process or wait for the reset process to finish when unloading
if hardware is resetting.
So this patch provides these interfaces to do it.
1. get_hw_reset_stat, the reset status of hardware.
2. ae_dev_resetting, whether reset task is scheduling.
3. ae_dev_reset_cnt, how many reset has been done.
Also, the RoCE client needs some field in the hnae3_roce_private_info
to save its state, and process_hw_error interface in the
hnae3_client_ops to process hardware errors.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:08 +0000 (12:06 +0800)]
net: hns3: add set_default_reset_request in the hnae3_ae_ops
Currently, when reset_event is called because of tx timeout, it will
upgrade the reset level (For PF, HNAE3_FUNC_RESET -> HNAE3_CORE_RESET
-> HNAE3_GLOBAL_RESET) if the time between the new reset and last reset
is within 20 secs, or restore the reset level to HNAE3_FUNC_RESET if
the time between the new reset and last reset is over 20 secs.
There is requirement that the caller needs to decide the reset level
when triggering a reset, for example, RAS recovery. So this patch
adds the set_default_reset_request to meet this requirement.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 7 Nov 2018 04:06:07 +0000 (12:06 +0800)]
net: hns3: use HNS3_NIC_STATE_INITED to indicate the initialization state of enet
Besides of module_init and module_exit, the process of reset will
also uninitialize and initialize the enet client. When reset process
fails with enet client uninitialized, the module_exit does not need
to uninitialize the enet client, otherwise it may cause double
uninitialization problem.
So we need the HNS3_NIC_STATE_INITED flag to indicate whether
the enet client is initialized.
Also HNS3_NIC_STATE_REINITING is previously unused, so change it to
HNS3_NIC_STATE_INITED.
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: systemport: Unmap queues upon DSA unregister event
This patch series fixes the unbinding/binding of the bcm_sf2 switch
driver along with bcmsysport which monitors the switch port queues.
Because the driver was not processing the DSA_PORT_UNREGISTER event, we
would not be unmapping switch port/queues, which could cause incorrect
decisions to be made by the HW (e.g: queue always back-pressured).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Unmap queues upon DSA unregister event
Binding and unbinding the switch driver which creates the DSA slave
network devices for which we set-up inspection would lead to
undesireable effects since we were not clearing the port/queue mapping
to the SYSTEMPORT TX queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Turn on PHY to allow successful registration
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: dsa: bcm_sf2: Store rules in lists
This patch series changes the bcm-sf2 driver to keep a copy of the
inserted rules as opposed to using the HW as a storage area for a number
of reasons:
- this helps us with doing duplicate rule detection in a faster way, it
would have required a full rule read before
- this helps with Pablo's on-going work to convert ethtool_rx_flow_spec
to a more generic flow rule structure by having fewer code paths to
convert to the new structure/helpers
- we need to cache copies to restore them during drive resumption,
because depending on the low power mode the system has entered, the
switch may have lost all of its context
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: systemport: Restore Broadcom tag match filters upon resume
Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Get rid of unmarshalling functions
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Restore CFP rules during system resume
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Split rule handling from HW operation
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 6 Nov 2018 23:00:45 +0000 (15:00 -0800)]
Merge branch 'net-More-extack-messages'
David Ahern says:
====================
net: More extack messages
Add more extack messages for several link create errors (e.g., invalid
number of queues, unknown link kind) and invalid metrics argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 6 Nov 2018 20:51:16 +0000 (12:51 -0800)]
rtnetlink: Add more extack messages to rtnl_newlink
Add extack arg to the nla_parse_nested calls in rtnl_newlink, and
add messages for unknown device type and link network namespace id.
In particular, it improves the failure message when the wrong link
type is used. From
$ ip li add bond1 type bonding
RTNETLINK answers: Operation not supported
to
$ ip li add bond1 type bonding
Error: Unknown device type.
(The module name is bonding but the link type is bond.)
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 2 Nov 2018 22:00:26 +0000 (15:00 -0700)]
ISDN: eicon: Remove driver
I started looking at the history of this driver, and last time the
maintainer was active on the mailing list was when discussing how to
remove it. This was in 2012:
It looks to me like this has in practice been an orphan for quite a while.
It's throwing warnings about stack size in a function that is in dire
need of refactoring, and it's probably a case of "it's time to call it".
Cc: Armin Schindler <mac@melware.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 6 Nov 2018 16:12:10 +0000 (08:12 -0800)]
Merge tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Masami found a slight bug in his code where he transposed the
arguments of a call to strpbrk.
The reason this wasn't detected in our tests is that the only way this
would transpire is when a kprobe event with a symbol offset is
attached to a function that belongs to a module that isn't loaded yet.
When the kprobe trace event is added, the offset would be truncated
after it was parsed, and when the module is loaded, it would use the
symbol without the offset (as the nul character added by the parsing
would not be replaced with the original character)"
* tag 'trace-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Fix strpbrk() argument order
Linus Torvalds [Tue, 6 Nov 2018 16:10:01 +0000 (08:10 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fix from Russell King:
"Ard spotted a typo in one of the assembly files which leads to a
kernel oops when that code path is executed. Fix this"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm
1) Handle errors mid-stream of an all dump, from Alexey Kodanev.
2) Fix build of openvswitch with certain combinations of netfilter
options, from Arnd Bergmann.
3) Fix interactions between GSO and BQL, from Eric Dumazet.
4) Don't put a '/' in RTL8201F's sysfs file name, from Holger
Hoffstätte.
5) S390 qeth driver fixes from Julian Wiedmann.
6) Allow ipv6 link local addresses for netconsole when both source and
destination are link local, from Matwey V. Kornilov.
7) Fix the BPF program address seen in /proc/kallsyms, from Song Liu.
8) Initialize mutex before use in dsa microchip driver, from Tristram
Ha.
9) Out-of-bounds access in hns3, from Yunsheng Lin.
10) Various netfilter fixes from Stefano Brivio, Jozsef Kadlecsik, Jiri
Slaby, Florian Westphal, Eric Westbrook, Andrey Ryabinin, and Pablo
Neira Ayuso.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (50 commits)
net: alx: make alx_drv_name static
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
sock_diag: fix autoloading of the raw_diag module
net: core: netpoll: Enable netconsole IPv6 link local address
ipv6: properly check return value in inet6_dump_all()
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
bonding/802.3ad: fix link_failure_count tracking
net: phy: realtek: fix RTL8201F sysfs name
sctp: define SCTP_SS_DEFAULT for Stream schedulers
sctp: fix strchange_flags name for Stream Change Event
mlxsw: spectrum: Fix IP2ME CPU policer configuration
openvswitch: fix linking without CONFIG_NF_CONNTRACK_LABELS
qed: fix link config error handling
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
net/mlx4_en: use __netdev_tx_sent_queue()
net: do not abort bulk send on BQL status
net: bql: add __netdev_tx_sent_queue()
s390/qeth: report 25Gbit link speed
s390/qeth: sanitize ARP requests
...
Ard Biesheuvel [Mon, 5 Nov 2018 13:54:56 +0000 (14:54 +0100)]
ARM: 8809/1: proc-v7: fix Thumb annotation of cpu_v7_hvc_switch_mm
Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.
Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:
Cc: <stable@vger.kernel.org> Fixes: 10115105cb3a ("ARM: spectre-v2: add firmware based hardening") Reviewed-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The following patchset contains the first batch of Netfilter fixes for
your net tree:
1) Fix splat with IPv6 defragmenting locally generated fragments,
from Florian Westphal.
2) Fix Incorrect check for missing attribute in nft_osf.
3) Missing INT_MIN & INT_MAX definition for netfilter bridge uapi
header, from Jiri Slaby.
4) Revert map lookup in nft_numgen, this is already possible with
the existing infrastructure without this extension.
5) Fix wrong listing of set reference counter, make counter
synchronous again, from Stefano Brivio.
6) Fix CIDR 0 in hash:net,port,net, from Eric Westbrook.
7) Fix allocation failure with large set, use kvcalloc().
From Andrey Ryabinin.
8) No need to disable BH when fetch ip set comment, patch from
Jozsef Kadlecsik.
9) Sanity check for valid sysfs entry in xt_IDLETIMER, from
Taehee Yoo.
10) Fix suspicious rcu usage via ip_set() macro at netlink dump,
from Jozsef Kadlecsik.
11) Fix setting default timeout via nfnetlink_cttimeout, this
comes with preparation patch to add nf_{tcp,udp,...}_pernet()
helper.
12) Allow ebtables table nat to be of filter type via nft_compat.
From Florian Westphal.
13) Incorrect calculation of next bucket in early_drop, do no bump
hash value, update bucket counter instead. From Vasily Khoruzhick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Mon, 5 Nov 2018 13:31:41 +0000 (22:31 +0900)]
net: bpfilter: fix iptables failure if bpfilter_umh is disabled
When iptables command is executed, ip_{set/get}sockopt() try to upload
bpfilter.ko if bpfilter is enabled. if it couldn't find bpfilter.ko,
command is failed.
bpfilter.ko is generated if CONFIG_BPFILTER_UMH is enabled.
ip_{set/get}sockopt() only checks CONFIG_BPFILTER.
So that if CONFIG_BPFILTER is enabled and CONFIG_BPFILTER_UMH is disabled,
iptables command is always failed.
test config:
CONFIG_BPFILTER=y
# CONFIG_BPFILTER_UMH is not set
test command:
%iptables -L
iptables: No chain/target/match by that name.
Fixes: d2ba09c17a06 ("net: add skeleton of bpfilter kernel module") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei Vagin [Mon, 5 Nov 2018 06:37:15 +0000 (22:37 -0800)]
sock_diag: fix autoloading of the raw_diag module
IPPROTO_RAW isn't registred as an inet protocol, so
inet_protos[protocol] is always NULL for it.
Cc: Cyrill Gorcunov <gorcunov@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Fixes: bf2ae2e4bf93 ("sock_diag: request _diag module only when the family or proto has been registered") Signed-off-by: Andrei Vagin <avagin@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 2 Nov 2018 16:11:05 +0000 (19:11 +0300)]
ipv6: properly check return value in inet6_dump_all()
Make sure we call fib6_dump_end() if it happens that skb->len
is zero. rtnl_dump_all() can reset cb->args on the next loop
iteration there.
Fixes: 08e814c9e8eb ("net/ipv6: Bail early if user only wants cloned entries") Fixes: ae677bbb4441 ("net: Don't return invalid table id error when dumping all families") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 2 Nov 2018 16:11:04 +0000 (19:11 +0300)]
rtnetlink: restore handling of dumpit return value in rtnl_dump_all()
For non-zero return from dumpit() we should break the loop
in rtnl_dump_all() and return the result. Otherwise, e.g.,
we could get the memory leak in inet6_dump_fib() [1]. The
pointer to the allocated struct fib6_walker there (saved
in cb->args) can be lost, reset on the next iteration.
Fix it by partially restoring the previous behavior before
commit c63586dc9b3e ("net: rtnl_dump_all needs to propagate
error from dumpit function"). The returned error from
dumpit() is still passed further.
Fixes: c63586dc9b3e ("net: rtnl_dump_all needs to propagate error from dumpit function") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Barnhill [Mon, 5 Nov 2018 20:36:45 +0000 (20:36 +0000)]
net/ipv6: Move anycast init/cleanup functions out of CONFIG_PROC_FS
Move the anycast.c init and cleanup functions which were inadvertently
added inside the CONFIG_PROC_FS definition.
Fixes: 2384d02520ff ("net/ipv6: Add anycast addresses to a global hashtable") Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
compiler: remove __no_sanitize_address_or_inline again
The __no_sanitize_address_or_inline and __no_kasan_or_inline defines
are almost identical. The only difference is that __no_kasan_or_inline
does not have the 'notrace' attribute.
To be able to replace __no_sanitize_address_or_inline with the older
definition, add 'notrace' to __no_kasan_or_inline and change to two
users of __no_sanitize_address_or_inline in the s390 code.
The 'notrace' option is necessary for e.g. the __load_psw_mask function
in arch/s390/include/asm/processor.h. Without the option it is possible
to trace __load_psw_mask which leads to kernel stack overflow.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Pointed-out-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix strpbrk()'s argument order, it must pass acceptable string
in 2nd argument. Note that this can cause a kernel panic where
it recovers backup character to code->data.
Jarod Wilson [Sun, 4 Nov 2018 19:59:46 +0000 (14:59 -0500)]
bonding/802.3ad: fix link_failure_count tracking
Commit 4d2c0cda07448ea6980f00102dc3964eb25e241c set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda0744 ("bonding: speed/duplex update at NETDEV_UP event") CC: Mahesh Bandewar <maheshb@google.com> CC: David S. Miller <davem@davemloft.net> CC: netdev@vger.kernel.org CC: stable@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 4 Nov 2018 22:46:04 +0000 (14:46 -0800)]
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Linus Torvalds [Sun, 4 Nov 2018 16:20:09 +0000 (08:20 -0800)]
Merge tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Bugfix:
- Fix build issues on architectures that don't provide 64-bit cmpxchg
Cleanups:
- Fix a spelling mistake"
* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: fix spelling mistake, EACCESS -> EACCES
SUNRPC: Use atomic(64)_t for seq_send(64)
Linus Torvalds [Sun, 4 Nov 2018 16:12:44 +0000 (08:12 -0800)]
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
Xin Long [Sat, 3 Nov 2018 06:01:31 +0000 (14:01 +0800)]
sctp: define SCTP_SS_DEFAULT for Stream schedulers
According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.
SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sat, 3 Nov 2018 05:59:45 +0000 (13:59 +0800)]
sctp: fix strchange_flags name for Stream Change Event
As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.
To keep the compatibility, fix it by adding two macros.
Fixes: b444153fb5a6 ("sctp: add support for generating add stream change event notification") Reported-by: Jianwen Ji <jiji@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
to not use page start but actual start instead to work correctly with
profiling e.g. finding hot instructions from stack traces. Also fix latter
with regards to dumping address and jited len for !multi prog, from Song.
2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Fri, 2 Nov 2018 19:49:15 +0000 (19:49 +0000)]
mlxsw: spectrum: Fix IP2ME CPU policer configuration
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73ce ("mlxsw: spectrum: Add policers for trap groups") Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 2 Nov 2018 15:36:24 +0000 (16:36 +0100)]
qed: fix link config error handling
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7aa ("qed: Add supported link and advertise link to display in ethtool.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 4 Nov 2018 01:37:09 +0000 (18:37 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Linus Torvalds [Sun, 4 Nov 2018 01:25:17 +0000 (18:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Linus Torvalds [Sun, 4 Nov 2018 01:13:43 +0000 (18:13 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Linus Torvalds [Sun, 4 Nov 2018 01:12:09 +0000 (18:12 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
projects / mirror_ubuntu-hirsute-kernel.git / log