mmc: host: omap_hsmmc: use mmc_regulator_get_supply() to get regulators
In preparation for using the generic mmc binding for io regulator
("vqmmc"), use mmc_regulator_get_supply() to get vmmc and vqmmc regulators.
Only if "vqmmc" regulator isn't found, fallback to use "vmmc_aux"
regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: host: omap_hsmmc: Do not initialize MMC regulators to NULL on error
Do not initialize MMC regulators to NULL on error in omap_hsmmc driver
similar to what is done in mmc_regulator_get_supply(). This is in
preparation for using mmc_regulator_get_supply() to get MMC
regulators.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ARM: dts: omap3-overo: Remove "vqmmc-supply" property from MMC dt node
commit 94647a30124e2c7 ("ARM: dts: omap3-overo: Enable WiFi/BT combo")
while enabling WiFi/BT combo added regulator to trigger the nReset
signal of the Bluetooth module in vqmmc-supply. However BT should be
handled by UART. Moreover "vqmmc" is not a defined binding for
omap_hsmmc. While "vqmmc" in mmc2 hasn't caused any issues so far,
mmc2 will start to mis-behave once omap_hsmmc defines "vqmmc"
binding.
Remove "vqmmc-supply" property in mmc2 here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 9 Jun 2017 12:27:18 +0000 (15:27 +0300)]
mmc: sdio: Keep card runtime resumed while adding function devices
Drivers core will runtime suspend a device with no driver. That means the
SDIO card will be runtime suspended as soon as it is added. It is then
runtime resumed to add each function. That is entirely pointless, so add
pm runtime get/put to keep the SDIO card runtime resumed until the function
devices have been added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 9 Jun 2017 12:27:17 +0000 (15:27 +0300)]
mmc: sdio: Tidy error path in mmc_attach_sdio()
The error path deletes the device by calling mmc_sdio_remove() which must
be called without the host claimed. Simplify the error path so it does just
that and add a comment about why we don't disable runtime PM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The acpi-subsys already calls acpi_bus_get_status() and checks that
device->status.present is set before even registering the platform_device
so out probe function will never get called if device->status.present is
false and there is no need for this check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Tue, 23 May 2017 13:34:08 +0000 (15:34 +0200)]
mmc: tmio: make sure SDIO gets reinitialized after resume
To achieve that, we set the registers in the generic HW reset routine
which gets called at both, init and resume. We also make sure to move
SDIO initialization before reset gets called in probe().
Matthias Kraemer [Mon, 15 May 2017 21:44:17 +0000 (23:44 +0200)]
mmc: sdhci-pci: Use macros in pci_ids definition
This patch applies customized PCI_DEVICE_ macros to specify the pci_ids
instead of open-coding them within the sdhci-pci driver.
By introducing device specific macros the pci_ids table becomes much
shorter and easier to comprehend than it would be possible using the
generic version of the PCI_DEVICE_ macros.
mmc: sdhci-esdhc-imx: Remove the ENGcm07207 workaround
The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
(300 kB/s on average), and this erratum actually does not imply that
multiple-block transfers are not supported, so this was overkill.
The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
simple DAT line software reset (which resets the DMA circuit among
others) triggered by sdhci_finish_data() in case of errors seems to be
sufficient. Indeed, generating errors in a controlled manner on i.MX25
using the FEVT register right in the middle of read data transfers
without this quirk shows that nothing is written to the buffer by the
eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
the data transfers on AHB are properly aborted. For write data
transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
Moreover, after intensive stress tests on i.MX25, removing
SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.
SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set
ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set
in order to continue getting SDHCI_QUIRK_BROKEN_ADMA.
mmc: sdhci-esdhc-imx: Allow all supported prescaler values
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.
In DDR mode, the prescaler can divide by up to 512.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly
clears at least the data transfer width (PROCTL.DTW), which then results
in data CRC errors. This behavior is not documented, but it has actually
been observed. Consequently, the DAT line software resets triggered by
sdhci.c in case of errors caused unrecoverable errors.
Fix this by making sure that the DAT line software reset does not alter
the Host Control register. This behavior being undocumented, it may also
be present on other i.MX SoCs, so apply this fix for the whole i.MX
family.
Null check at line 1165: if (mrq->cmd), implies that mrq->cmd might
be NULL.
Add null checks before dereferencing pointer mrq->cmd in order to avoid
any potential NULL pointer dereference.
Addresses-Coverity-ID: 1408740 Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Mon, 22 May 2017 08:23:58 +0000 (10:23 +0200)]
mmc: block: Use __mmc_send_status() and drop get_card_status()
The only reason to why the mmc block device driver needs to implements its
own version of how to get the status of the card, is that it needs to
specify a different amount of retries.
Therefore add a new exported function which allows the caller to specify
the number of retries and convert everybody to use it, as this simplifies
the code.
Linus Walleij [Fri, 19 May 2017 13:37:30 +0000 (15:37 +0200)]
mmc: block: Move boot partition locking into a driver op
This moves the boot partition lock command (issued from sysfs)
into a custom block layer request, just like the ioctl()s,
getting rid of yet another instance of mmc_get_card().
Since we now have two operations issuing special DRV_OP's, we
rename the result variable ->drv_op_result.
Tested by locking the boot partition from userspace:
> cd /sys/devices/platform/soc/80114000.sdi4_per2/mmc_host/mmc3/
mmc3:0001/block/mmcblk3/mmcblk3boot0
> echo 1 > ro_lock_until_next_power_on
[ 178.645324] mmcblk3boot1: Locking boot partition ro until next power on
[ 178.652221] mmcblk3boot0: Locking boot partition ro until next power on
Also tested this with a huge dd job in the background: it
is now possible to lock the boot partitions on the card even
under heavy I/O.
Linus Walleij [Fri, 19 May 2017 13:37:29 +0000 (15:37 +0200)]
mmc: block: Move DRV OP issue function
We will need to access static functions above the pure block layer
operations in the file, so move the driver operations issue
function down so we can see all non-blocklayer symbols.
Linus Walleij [Fri, 19 May 2017 13:37:28 +0000 (15:37 +0200)]
mmc: block: Tag DRV_OPs with a driver operation type
We will expand the DRV_OP usage, so we need to know which
operation we're performing. Tag the operations with an
enum:ed type and rename the function so it is clear that
it deals with any command and put a switch statement in
it. Currently only ioctls are supported.
Linus Walleij [Fri, 19 May 2017 13:37:27 +0000 (15:37 +0200)]
mmc: block: remove req back pointer
Just as we can use blk_mq_rq_from_pdu() to get the per-request
tag we can use blk_mq_rq_to_pdu() to get a request from a tag.
Introduce a static inline helper so we are on the clear what
is happening.
Wolfram Sang [Fri, 19 May 2017 13:31:52 +0000 (15:31 +0200)]
mmc: tmio: remove outdated comment
The obviously wrong comment was added in 2011 with commit df3ef2d3c92c0a
("mmc: protect the tmio_mmc driver against a theoretical race") but
already obsoleted half a year later with commit b9269fdd4f61aa ("mmc:
tmio: fix recursive spinlock, don't schedule with interrupts disabled").
Wolfram Sang [Fri, 19 May 2017 13:31:50 +0000 (15:31 +0200)]
mmc: tmio: make tmio_mmc_request function more readable
This part confused me and I had to read it twice until I got it. Let's
follow the standard pattern to bail out if something is wrong and keep
in the body of the function when everything is as expected.
Linus Walleij [Thu, 18 May 2017 09:29:36 +0000 (11:29 +0200)]
mmc: queue: delete mmc_req_is_special()
commit cdf8a6fb48882651049e468e6b16956fb83db86c
"mmc: block: Introduce queue semantics"
deleted the last user of mmc_req_is_special() and it was
a horrible hack to classify requests as "special" or
"not special" to begin with, so delete the helper.
Linus Walleij [Thu, 18 May 2017 09:29:34 +0000 (11:29 +0200)]
mmc: block: move single ioctl() commands to block requests
This wraps single ioctl() commands into block requests using
the custom block layer request types REQ_OP_DRV_IN and
REQ_OP_DRV_OUT.
By doing this we are loosening the grip on the big host lock,
since two calls to mmc_get_card()/mmc_put_card() are removed.
We are storing the ioctl() in/out argument as a pointer in
the per-request struct mmc_blk_request container. Since we
now let the block layer allocate this data, blk_get_request()
will allocate it for us and we can immediately dereference
it and use it to pass the argument into the block layer.
We refactor the if/else/if/else ladder in mmc_blk_issue_rq()
as part of the job, keeping some extra attention to the
case when a NULL req is passed into this function and
making that pipeline flush more explicit.
Tested on the ux500 with the userspace:
mmc extcsd read /dev/mmcblk3
resulting in a successful EXTCSD info dump back to the
console.
This commit fixes a starvation issue in the MMC/SD stack
that can be easily provoked in the following way by
issueing the following commands in sequence:
Before this patch, the extcsd read command would hang
(starve) while waiting for the dd command to finish since
the block layer was holding the card/host lock.
After this patch, the extcsd ioctl() command is nicely
interpersed with the rest of the block commands and we
can issue a bunch of ioctl()s from userspace while there
is some busy block IO going on without any problems.
Conversely userspace ioctl()s can no longer starve
the block layer by holding the card/host lock.
Linus Walleij [Thu, 18 May 2017 09:29:32 +0000 (11:29 +0200)]
mmc: core: Allocate per-request data using the block layer core
The mmc_queue_req is a per-request state container the MMC core uses
to carry bounce buffers, pointers to asynchronous requests and so on.
Currently allocated as a static array of objects, then as a request
comes in, a mmc_queue_req is assigned to it, and used during the
lifetime of the request.
This is backwards compared to how other block layer drivers work:
they usally let the block core provide a per-request struct that get
allocated right beind the struct request, and which can be obtained
using the blk_mq_rq_to_pdu() helper. (The _mq_ infix in this function
name is misleading: it is used by both the old and the MQ block
layer.)
The per-request struct gets allocated to the size stored in the queue
variable .cmd_size initialized using the .init_rq_fn() and
cleaned up using .exit_rq_fn().
The block layer code makes the MMC core rely on this mechanism to
allocate the per-request mmc_queue_req state container.
Doing this make a lot of complicated queue handling go away. We only
need to keep the .qnct that keeps count of how many request are
currently being processed by the MMC layer. The MQ block layer will
replace also this once we transition to it.
Doing this refactoring is necessary to move the ioctl() operations
into custom block layer requests tagged with REQ_OP_DRV_[IN|OUT]
instead of the custom code using the BigMMCHostLock that we have
today: those require that per-request data be obtainable easily from
a request after creating a custom request with e.g.:
And this is not possible with the current construction, as the request
is not immediately assigned the per-request state container, but
instead it gets assigned when the request finally enters the MMC
queue, which is way too late for custom requests.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf: Folded in the fix to drop a call to blk_cleanup_queue()] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Linus Walleij [Thu, 18 May 2017 09:29:31 +0000 (11:29 +0200)]
mmc: core: Delete bounce buffer Kconfig option
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.
It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.
Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.
The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.
Those are the following:
arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
host->disable_bounce to true in the host driver
arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform
arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
which is 128, unless a DMA engine is used, and in that case
the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms
arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
disabled at runtime
- No special action needed for this platform
arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
runtime
- No special action needed for these platforms
arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case
arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
already runtime disabled
- No action needed for this platform
It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename the source file for DMA for SDHI as a follow-up to attaching
DMA code to the SDHI driver rather than the tmio_core driver.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
The name sys_dmac was chosen to reflect the type of DMA used.
Internal symbols have also been renamed to reflect the filename change.
A follow-up patch will re-organise the SDHI driver removing
the need for renesas_sdhi_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Simon Horman [Wed, 10 May 2017 09:25:26 +0000 (11:25 +0200)]
mmc: renesas-sdhi, tmio: make dma more modular
Refactor DMA support to allow it to be provided by a set of call-backs
that are provided by a host driver. The motivation is to allow multiple
DMA implementations to be provided and instantiated at run-time.
Instantiate the existing DMA implementation from the sh_mobile_sdhi driver
which appears to match the current use-case. This has the side effect
of moving the DMA code from the tmio_core to the sh_mobile_sdhi driver.
A follow-up patch will change the source file for the SDHI DMA
implementation accordingly. Another follow-up patch will re-organise the
SDHI driver removing the need for tmio_mmc_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Revert "mmc: dw_mmc: Don't allow Runtime PM for SDIO cards"
This reverts commit a6db2c86033b ("mmc: dw_mmc: Don't allow Runtime PM for
SDIO cards")'
As dw_mmc now is capable of preventing runtime PM suspend while SDIO IRQs
are enabled, let's drop the less fine-grained method, which is preventing
runtime PM suspend for all SDIO cards - no matter of whether SDIO IRQs are
being enabled or not.
In this way we don't keep the host runtime PM resumed, unless it's really
needed, thus avoiding to waste power.
Especially when SDIO IRQs is supported via a separate out-of-band IRQ line,
which isn't defined by the SDIO standard, typically the SDIO func driver
doesn't enable SDIO IRQs via sdio_claim_irq(). So, for these cases we can
now allow the dwmmc device to be runtime PM suspended in-between requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
mmc: dw_mmc: Prevent runtime PM suspend when SDIO IRQs are enabled
To be able to handle SDIO IRQs the dw_mmc device needs to be powered and
providing clock to the SDIO card. Therefore, we must not allow the device
to be runtime PM suspended while SDIO IRQs are enabled.
To fix this, let's increase the runtime PM usage count while the mmc core
enables SDIO IRQs. Later when the mmc core tells dw_mmc to disable SDIO
IRQs, we drop the usage count to again allow runtime PM suspend.
This now becomes the default behaviour for dw_mmc. In cases where SDIO IRQs
can be re-routed as GPIO wake-ups during runtime PM suspend, one could
potentially allow runtime PM suspend. However, that will have to be
addressed as a separate change on top of this one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
mmc: dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
Convert to use the more lightweight method for processing SDIO IRQs, which
involves the following changes:
- Enable MMC_CAP2_SDIO_IRQ_NOTHREAD when SDIO IRQ is supported and use
sdio_signal_irq() instead of mmc_signal_sdio_irq().
- Mask the SDIO IRQ before signaling a new one to be processed.
- Implement the ->ack_sdio_irq() callback to unmask the SDIO IRQ.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
mmc: sdio: Add API to manage SDIO IRQs from a workqueue
For hosts not supporting MMC_CAP2_SDIO_IRQ_NOTHREAD but MMC_CAP_SDIO_IRQ,
the SDIO IRQs are processed from a dedicated kernel thread. For these
cases, the host calls mmc_signal_sdio_irq() from its ISR to signal a new
SDIO IRQ.
Signaling an SDIO IRQ makes the host's ->enable_sdio_irq() callback to be
invoked to temporary disable the IRQs, before the kernel thread is woken up
to process it. When processing of the IRQs are completed, they are
re-enabled by the kernel thread, again via invoking the host's
->enable_sdio_irq().
The observation from this, is that the execution path is being unnecessary
complex, as the host driver already knows that it needs to temporary
disable the IRQs before signaling a new one. Moreover, replacing the kernel
thread with a work/workqueue would not only greatly simplify the code, but
also make it more robust.
To address the above problems, let's continue to build upon the support for
MMC_CAP2_SDIO_IRQ_NOTHREAD, as it already implements SDIO IRQs to be
processed without using the clumsy kernel thread and without the ping-pong
calls of the host's ->enable_sdio_irq() callback for each processed IRQ.
Therefore, let's add new API sdio_signal_irq(), which enables hosts to
signal/process SDIO IRQs by using a work/workqueue, rather than using the
kernel thread.
Add also a new host callback ->ack_sdio_irq(), which the work invokes when
the SDIO IRQs have been processed. This informs the host about when it
shall re-enable the SDIO IRQs. Potentially, we could re-use the existing
->enable_sdio_irq() callback instead of adding a new one, however it has
turned out that it's more convenient for hosts to get this information via
a separate callback.
Hosts that wants to use this new method to signal/process SDIO IRQs, must
enable MMC_CAP2_SDIO_IRQ_NOTHREAD and implement the ->ack_sdio_irq()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
mmc: core: Prevent processing SDIO IRQs when none is claimed
In cases when MMC_CAP2_SDIO_IRQ_NOTHREAD is set, there is a minor window
for when the mmc host could call sdio_run_irqs(), while in fact an SDIO
func driver could have decided to released the SDIO IRQ via a call to
sdio_release_irq(). In this scenario, processing of the SDIO IRQs are done
even if there is none IRQ claimed, which is not what we want.
To prevent this from happen, close the window by validating that at least
one SDIO IRQs is claimed, before deciding to process them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Ulf Hansson [Mon, 8 May 2017 21:52:04 +0000 (23:52 +0200)]
mmc: core: Don't do eMMC HW reset when resuming the eMMC card
In case if a pwrseq-emmc has been bound to the host, a call to
mmc_power_up() triggers an eMMC HW reset via the pwrseq_emmc's
->post_power_on() callback. This isn't really what we want, as
mmc_power_up() is called each time when resuming the card.
As a matter of fact, the current approach may also violate the eMMC spec,
as the involved delays managed in pwrseq_emmc assumes both VCC and VCCQ has
been turned on, which isn't the case for VCCQ, unless the regulator is
always on.
Fix this behaviour by aligning to the same procedure used when the mmc host
implements the ->hw_reset() callback and has the MMC_CAP_HW_RESET flag set.
In this way the eMMC HW reset is issued at card detection scan, to cope
with bogus bootloaders and in the error recovery path via the mmc specific
bus_ops->reset() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Colin Ian King [Tue, 9 May 2017 15:45:04 +0000 (16:45 +0100)]
mmc: sdricoh_cs: remove redundant check if len is non-zero
At the end of either of the read or write loops len is always zero
and hence the non-zero check on len and return of -EIO is redundant
and can be removed.
Detected by CoverityScan, CID#114293 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hugh Dickins [Mon, 19 Jun 2017 11:03:24 +0000 (04:03 -0700)]
mm: larger stack guard gap, between vmas
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Olof Johansson [Mon, 19 Jun 2017 03:42:21 +0000 (20:42 -0700)]
Merge tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.12
A few fixes around the PRCM support that got in 4.12 with a wrong
compatible, and a missing clock in the binding.
* tag 'sunxi-fixes-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
arm64: allwinner: h5: Remove syslink to shared DTSI
ARM: sunxi: h3/h5: fix the compatible of R_CCU
Linus Torvalds [Mon, 19 Jun 2017 00:25:05 +0000 (09:25 +0900)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfix from Michael Tsirkin:
"It turns out balloon does not handle IOMMUs correctly. We should fix
that at some point, for now let's just disable this configuration"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: disable VIOMMU support
Linus Torvalds [Mon, 19 Jun 2017 00:20:25 +0000 (09:20 +0900)]
Merge branch 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two driver bugfixes"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
Linus Torvalds [Mon, 19 Jun 2017 00:01:01 +0000 (09:01 +0900)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
- Three highmem fixes:
+ Fixed mapping initialization
+ Adjust the pkmap location
+ Ensure we use at most one page for PTEs
- Fix makefile dependencies for .its targets to depend on vmlinux
- Fix reversed condition in BNEZC and JIALC software branch emulation
- Only flush initialized flush_insn_slot to avoid NULL pointer
dereference
- perf: Remove incorrect odd/even counter handling for I6400
- ftrace: Fix init functions tracing
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: .its targets depend on vmlinux
MIPS: Fix bnezc/jialc return address calculation
MIPS: kprobes: flush_insn_slot should flush only if probe initialised
MIPS: ftrace: fix init functions tracing
MIPS: mm: adjust PKMAP location
MIPS: highmem: ensure that we don't use more than one page for PTEs
MIPS: mm: fixed mappings: correct initialisation
MIPS: perf: Remove incorrect odd/even counter handling for I6400
virtio balloon bypasses the DMA API entirely so does not support the
VIOMMU right now. It's not clear we need that support, for now let's
just make sure we don't pretend to support it.
Cc: stable@vger.kernel.org Cc: Wei Wang <wei.w.wang@intel.com> Fixes: 1a937693993f ("virtio: new feature to detect IOMMU device quirk") Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Linus Torvalds [Sun, 18 Jun 2017 09:49:12 +0000 (18:49 +0900)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two fixlets for x86:
- Handle WARN_ONs proper with the new UD based WARN implementation
- Disable 1G mappings when 2M mappings are disabled by kmemleak or
debug_pagealloc. Otherwise 1G mappings might still be used,
confusing the debug mechanisms"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Disable 1GB direct mappings when disabling 2MB mappings
x86/debug: Handle early WARN_ONs proper
Linus Torvalds [Sun, 18 Jun 2017 09:46:51 +0000 (18:46 +0900)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets for timers:
- Two hot-fixes for the alarmtimer based posix timers, which prevent
a nasty DOS by self rescheduling timers. The proper cleanup of that
mess is queued for 4.13
- Make a function static"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Make tick_broadcast_setup_oneshot() static
alarmtimer: Rate limit periodic intervals
alarmtimer: Prevent overflow of relative timers
Linus Torvalds [Sun, 18 Jun 2017 09:45:17 +0000 (18:45 +0900)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two small fixes for the schedulre core:
- Use the proper switch_mm() variant in idle_task_exit() because that
code is not called with interrupts disabled.
- Fix a confusing typo in a printk"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Idle_task_exit() shouldn't use switch_mm_irqs_off()
sched/fair: Fix typo in printk message
Linus Torvalds [Sat, 17 Jun 2017 23:51:35 +0000 (08:51 +0900)]
Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Two LED fixes:
- fix signal source assignment for leds-bcm6328
- revert patch that intended to fix LED behavior on suspend but it
had a side effect preventing suspend at all due to uevent being
sent on trigger removal"
* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Revert "leds: handle suspend/resume in heartbeat trigger"
leds: bcm6328: fix signal source assignment for leds 4 to 7
Linus Torvalds [Sat, 17 Jun 2017 23:39:54 +0000 (08:39 +0900)]
Merge tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small gadget and xhci USB fixes for 4.12-rc6.
Nothing major, but one of the gadget patches does fix a reported oops,
and the xhci ones resolve reported problems. All have been in
linux-next with no reported issues"
* tag 'usb-4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
usb: xhci: ASMedia ASM1042A chipset need shorts TX quirk
usb: xhci: Fix USB 3.1 supported protocol parsing
USB: gadget: fix GPF in gadgetfs
usb: gadget: composite: make sure to reactivate function on unbind
Linus Torvalds [Sat, 17 Jun 2017 23:23:02 +0000 (08:23 +0900)]
Merge tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for an old ceph ->fh_to_* bug from Luis and two timestamp fixups
from Zheng, prompted by the ongoing y2038 work"
* tag 'ceph-for-4.12-rc6' of git://github.com/ceph/ceph-client:
ceph: unify inode i_ctime update
ceph: use current_kernel_time() to get request time stamp
ceph: check i_nlink while converting a file handle to dentry
Linus Torvalds [Sat, 17 Jun 2017 08:30:07 +0000 (17:30 +0900)]
Merge branch 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull ufs fixes from Al Viro:
"Fix assorted ufs bugs: a couple of deadlocks, fs corruption in
truncate(), oopsen on tail unpacking and truncate when racing with
vmscan, mild fs corruption (free blocks stats summary buggered, *BSD
fsck would complain and fix), several instances of broken logics
around reserved blocks (starting with "check almost never triggers
when it should" and then there are issues with sufficiently large
UFS2)"
[ Note: ufs hasn't gotten any loving in a long time, because nobody
really seems to use it. These ufs fixes are triggered by people
actually caring now, not some sudden influx of new bugs. - Linus ]
* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs_truncate_blocks(): fix the case when size is in the last direct block
ufs: more deadlock prevention on tail unpacking
ufs: avoid grabbing ->truncate_mutex if possible
ufs_get_locked_page(): make sure we have buffer_heads
ufs: fix s_size/s_dsize users
ufs: fix reserved blocks check
ufs: make ufs_freespace() return signed
ufs: fix logics in "ufs: make fsck -f happy"
Linus Torvalds [Sat, 17 Jun 2017 08:26:53 +0000 (17:26 +0900)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes; a leak in mntns_install() caught by Andrei (this
cycle regression) + d_invalidate() softlockup fix - that had been
reported by a bunch of people lately, but the problem is pretty old"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: don't forget to put old mntns in mntns_install
Hang/soft lockup in d_invalidate with simultaneous calls
Linus Torvalds [Fri, 16 Jun 2017 21:53:20 +0000 (06:53 +0900)]
Merge tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix another PCI_ENDPOINT build error (merged for v4.12)
- fix error codes added to config accessors for v4.12
* tag 'pci-v4.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: endpoint: Select CRC32 to fix test build error
PCI: Make error code types consistent in pci_{read,write}_config_*
Linus Torvalds [Fri, 16 Jun 2017 21:49:34 +0000 (06:49 +0900)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
zhongjiang [Fri, 16 Jun 2017 21:02:40 +0000 (14:02 -0700)]
mm: correct the comment when reclaimed pages exceed the scanned pages
Commit e1587a494540 ("mm: vmpressure: fix sending wrong events on
underflow") declared that reclaimed pages exceed the scanned pages due
to the thp reclaim.
That is incorrect because THP will be spilt to normal page and loop
again, which will result in the scanned pages increment.
Andrea Arcangeli [Fri, 16 Jun 2017 21:02:37 +0000 (14:02 -0700)]
userfaultfd: shmem: handle coredumping in handle_userfault()
Anon and hugetlbfs handle FOLL_DUMP set by get_dump_page() internally to
__get_user_pages().
shmem as opposed has no special FOLL_DUMP handling there so
handle_mm_fault() is invoked without mmap_sem and ends up calling
handle_userfault() that isn't expecting to be invoked without mmap_sem
held.
This makes handle_userfault() fail immediately if invoked through
shmem_vm_ops->fault during coredumping and solves the problem.
The side effect is a BUG_ON with no lock held triggered by the
coredumping process which exits. Only 4.11 is affected, pre-4.11 anon
memory holes are skipped in __get_user_pages by checking FOLL_DUMP
explicitly against empty pagetables (mm/gup.c:no_page_table()).
It's zero cost as we already had a check for current->flags to prevent
futex to trigger userfaults during exit (PF_EXITING).
Link: http://lkml.kernel.org/r/20170615214838.27429-1-aarcange@redhat.com Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Cc: <stable@vger.kernel.org> [4.11+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Rutland [Fri, 16 Jun 2017 21:02:34 +0000 (14:02 -0700)]
mm: numa: avoid waiting on freed migrated pages
In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by
waiting until the pmd is unlocked before we return and retry. However,
we can race with migrate_misplaced_transhuge_page():
// do_huge_pmd_numa_page // migrate_misplaced_transhuge_page()
// Holds 0 refs on page // Holds 2 refs on page
vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd);
/* ... */
if (pmd_trans_migrating(*vmf->pmd)) {
page = pmd_page(*vmf->pmd);
spin_unlock(vmf->ptl);
ptl = pmd_lock(mm, pmd);
if (page_count(page) != 2)) {
/* roll back */
}
/* ... */
mlock_migrate_page(new_page, page);
/* ... */
spin_unlock(ptl);
put_page(page);
put_page(page); // page freed here
wait_on_page_locked(page);
goto out;
}
This can result in the freed page having its waiters flag set
unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the
page alloc/free functions. This has been observed on arm64 KVM guests.
We can avoid this by having do_huge_pmd_numa_page() take a reference on
the page before dropping the pmd lock, mirroring what we do in
__migration_entry_wait().
When we hit the race, migrate_misplaced_transhuge_page() will see the
reference and abort the migration, as it may do today in other cases.
Fixes: b8916634b77bffb2 ("mm: Prevent parallel splits during THP migration") Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Steve Capper <steve.capper@arm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Morse [Fri, 16 Jun 2017 21:02:29 +0000 (14:02 -0700)]
mm/memory-failure.c: use compound_head() flags for huge pages
memory_failure() chooses a recovery action function based on the page
flags. For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:
> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed
Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead. This results in the me_huge_page() recovery
action being called:
> Memory failure: 0x9b7969: recovery action for huge page: Delayed
For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.
Fixes: 524fca1e7356 ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages") Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.com Signed-off-by: James Morse <james.morse@arm.com> Tested-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Jun 2017 20:57:54 +0000 (05:57 +0900)]
Merge tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Three small fixes for recently merged code:
- remove a spurious WARN_ON when a PCI device has no of_node, it's
allowed in some circumstances for there to be no of_node.
- fix the offset for store EOI MMIOs in the XIVE interrupt
controller.
- fix non-const WARN_ONs which were becoming BUGs due to them losing
BUGFLAG_WARNING in a recent cleanup patch.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Benjamin
Herrenschmidt"
* tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
powerpc/xive: Fix offset for store EOI MMIOs
powerpc/npu-dma: Remove spurious WARN_ON when a PCI device has no of_node
Ingo Molnar [Fri, 16 Jun 2017 19:33:48 +0000 (21:33 +0200)]
Merge tag 'perf-urgent-for-mingo-4.12-20170616' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix probing of precise_ip level for default cycles event, that
got broken recently on x86_64 when its arch code started
considering invalid requesting precise samples when not sampling
(i.e. when attr.sample_period == 0).
This also fixes another problem in s/390 where the precision
probing with sample_period == 0 returned precise_ip > 0, that
then, when setting up the real cycles event (not probing) would
return EOPNOTSUPP for precise_ip > 0 (as determined previously
by probing) and sample_period > 0.
These problems resulted in attr_precise not being set to the
highest precision available on x86.64 when no event was specified,
i.e. the canonical:
perf record ./workload
would end up using attr.precise_ip = 0. As a workaround this would
need to be done:
perf record -e cycles:P ./workload
And on s/390 it would plain not work, requiring using:
perf record -e cycles ./workload
as a workaround. (Arnaldo Carvalho de Melo)
- Fix perf build with ARCH=x86_64, when ARCH should be transformed
into ARCH=x86, just like with the main kernel Makefile and
tools/objtool's, i.e. use SRCARCH. (Jiada Wang)
- Avoid accessing uninitialized data structures when unwinding with
elfutils's libdw, making it more closely mimic libunwind's unwinder.
(Milian Wolff)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Milian Wolff [Fri, 2 Jun 2017 14:37:53 +0000 (16:37 +0200)]
perf unwind: Report module before querying isactivation in dwfl unwind
The PC returned by dwfl_frame_pc() may map into a not-yet-reported
module. We have to report it before we continue unwinding. But when we
query for the isactivation flag in dwfl_frame_pc, libdw will actually do
one more unwinding step internally which can then break and lead to
missed frames or broken stacks.
Linus Torvalds [Fri, 16 Jun 2017 09:45:47 +0000 (18:45 +0900)]
Merge tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A fix from Nic for a race seen in production (including a stable tag).
And while I'm sending you this I'm also sneaking in a trivial new
helper from Bart so that we don't need inter-tree dependencies for the
next merge window"
* tag 'configfs-for-4.12' of git://git.infradead.org/users/hch/configfs:
configfs: Introduce config_item_get_unless_zero()
configfs: Fix race between create_link and configfs_rmdir
Linus Torvalds [Fri, 16 Jun 2017 08:46:47 +0000 (17:46 +0900)]
Merge tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is the main fixes pull for 4.12-rc6, all pretty normal for this
stage, nothing really stands out. The mxsfb one is probably the
largest and it's for a black screen boot problem.
AMD, i915, mgag200, msxfb, tegra fixes"
* tag 'drm-fixes-for-v4.12-rc6' of git://people.freedesktop.org/~airlied/linux:
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
gpu: host1x: Fix error handling
drm/radeon: Fix overflow of watermark calcs at > 4k resolutions.
drm/amdgpu: Fix overflow of watermark calcs at > 4k resolutions.
drm/radeon: fix "force the UVD DPB into VRAM as well"
drm/i915: Fix GVT-g PVINFO version compatibility check
drm/i915: Fix SKL+ watermarks for 90/270 rotation
drm/i915: Fix scaling check for 90/270 degree plane rotation
drm: dw-hdmi: Fix compilation breakage by selecting REGMAP_MMIO
Linus Torvalds [Fri, 16 Jun 2017 08:38:23 +0000 (17:38 +0900)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I had thought at the time of the last pull request that there wouldn't
be much more to go, but several things just kept trickling in over the
last week.
Instead of just the six patches to bnxt_re that I had anticipated,
there are another five IPoIB patches, two qedr patches, and a few
other miscellaneous patches.
The bnxt_re patches are more lines of diff than I like to submit this
late in the game. That's mostly because of the first two patches in
the series of six. I almost dropped them just because of the lines of
churn, but on a close review, a lot of the churn came from removing
duplicated code sections and consolidating them into callable
routines. I felt like this made the number of lines of change more
acceptable, and they address problems, so I left them. The remainder
of the patches are all small, well contained, and well understood.
These have passed 0day testing, but have not been submitted to
linux-next (but a local merge test with your current master was
without any conflicts).
Summary:
- A fix for fix eea40b8f624 ("infiniband: call ipv6 route lookup via
the stub interface")
- Six patches against bnxt_re...the first two are considerably larger
than I would like, but as they address real issues I went ahead and
submitted them (it also helped that a good deal of the churn was
removing code repeated in multiple places and consolidating it to
one common function)
- Two fixes against qedr that just came in
- One fix against rxe that took a few revisions to get right plus
time to get the proper reviews
- Five late breaking IPoIB fixes
- One late cxgb4 fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
rdma/cxgb4: Fix memory leaks during module exit
IB/ipoib: Fix memory leak in create child syscall
IB/ipoib: Fix access to un-initialized napi struct
IB/ipoib: Delete napi in device uninit default
IB/ipoib: Limit call to free rdma_netdev for capable devices
IB/ipoib: Fix memory leaks for child interfaces priv
rxe: Fix a sleep-in-atomic bug in post_one_send
RDMA/qedr: Add 64KB PAGE_SIZE support to user-space queues
RDMA/qedr: Initialize byte_len in WC of READ and SEND commands
RDMA/bnxt_re: Remove FMR support
RDMA/bnxt_re: Fix RQE posting logic
RDMA/bnxt_re: Add HW workaround for avoiding stall for UD QPs
RDMA/bnxt_re: Dereg MR in FW before freeing the fast_reg_page_list
RDMA/bnxt_re: HW workarounds for handling specific conditions
RDMA/bnxt_re: Fixing the Control path command and response handling
IB/addr: Fix setting source address in addr6_resolve()
projects / mirror_ubuntu-bionic-kernel.git / log