Veaceslav Falico [Tue, 18 Feb 2014 06:48:37 +0000 (07:48 +0100)]
bonding: permit using arp_validate with non-ab modes
Currently it's disabled because it's sometimes hard, in typical configs, to
make it work - because of the nature how the loadbalance modes work - as
it's hard to deliver valid arp replies to correct slaves by the switch.
However we still can use arp_validation in loadbalance with several other
configs, per example with arp_validate == 2 for backup with one broadcast
domain, without the switch(es) doing any balancing - this way we'd be (a
bit more) sure that the slave is up.
So, enable it to let users decide which one works/suits them best. Also
correct the mode limitation from BOND_OPT_ARP_VALIDATE.
CC: Nikolay Aleksandrov <nikolay@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Tue, 18 Feb 2014 06:48:36 +0000 (07:48 +0100)]
bonding: remove bond->lock from bond_arp_rcv
We're always called with rcu_read_lock() held (bond_arp_rcv() is only
called from bond_handle_frame(), which is rx_handler and always called
under rcu from __netif_receive_skb_core() ).
The slave active/passive and/or bonding params can change in-flight, however
we don't really care about that - we only modify the last time packet was
received, which is harmless.
CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 18 Feb 2014 13:49:05 +0000 (21:49 +0800)]
r8152: move some functions from probe to open
Add up method for rtl_ops and asign relative functions. Move
clear_bp() and hw_phy_cfg() from init method to up method of rtl_ops.
Call rtl_ops.up() for ndo_open() and rtl_ops.down for ndo_stop().
Replace allocating the memory in probe() with in ndo_open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 18 Feb 2014 13:49:04 +0000 (21:49 +0800)]
r8152: combine PHY reset with set_speed
PHY reset is necessary after some hw settings. However, it would
cause the linking down, and so does the set_speed function. Combine
the PHY reset with set_speed function. That could reduce the frequency
of linking down and accessing the PHY register.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 18 Feb 2014 13:49:01 +0000 (21:49 +0800)]
r8152: load the default MAC address
Except for RTL_VER_01, replace loading the MAC address from PLA_IDR
with from PLA_BACKUP. The default MAC address may be modified by
the other OS, so the PLA_IDR may be not the default MAC address.
The data in the PLA_BACKUP address of the RTL_VER_01 may be destoryed,
so load MAC address from PLA_IDR for RTL_VER_01.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Tue, 18 Feb 2014 13:48:58 +0000 (21:48 +0800)]
r8152: move some functions
Move the following functions which is for the further coding.
- rtl_clear_bp
- r8153_clear_bp
- r8153_teredo_off
- r8152b_disable_aldps
- r8152b_enable_aldps
- r8152b_hw_phy_cfg
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Feb 2014 21:23:58 +0000 (16:23 -0500)]
Merge branch 'cxgb4'
Hariprasad Shenai says:
====================
Adds support for Chelsio T5 40G adapter and Misc. fixes
This patch series adds support for Chelsio T5 40G adapters and provides
miscelleneous fixes for cxgb4 driver.
It also adds device ids of two new T5 adapters.
We would like to request this patch series to get merged via David Miller's
'net-next' tree.
We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Tue, 18 Feb 2014 12:26:12 +0000 (17:56 +0530)]
cxgb4: Query firmware for T5 ULPTX MEMWRITE DSGL capabilities
Query firmware to see whether we're allowed to use T5 ULPTX MEMWRITE DSGL
capabilities. Also pass that information to Upper Layer Drivers via the
new (struct cxgb4_lld_info).ulptx_memwrite_dsgl boolean.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Tue, 18 Feb 2014 12:26:11 +0000 (17:56 +0530)]
cxgb4: LE-Workaround is not atomic in firmware
The LE workaround in firmware is not atomic and fw_ofld_connection_wrs must not interleave.
Therefore, when the workaround is enabled, we need to send all ctrlq WRs on a single ctrl queue.
Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kumar Sanghvi [Tue, 18 Feb 2014 12:26:08 +0000 (17:56 +0530)]
cxgb4: Add support to recognize 40G links
Also, create a new Common Code interface to translate Firmware Port Technology
Type values (enum fw_port_type) to string descriptions. This will allow us
to maintain the description translation table in one place rather than in
every driver.
Based on original work by Scott Bardone and Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Feb 2014 20:34:14 +0000 (15:34 -0500)]
Merge branch 'msix'
Alexander Gordeev says:
====================
net: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
wil6210: Use pci_enable_msi_range() instead of pci_enable_msi_block()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: wil6210@qca.qualcomm.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Cc: pv-drivers@vmware.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
This update cleans up the MSI-X/MSI enablement code, fixes
vmxnet3_acquire_msix_vectors() invalid return values and
enables a dead code in case VMXNET3_LINUX_MIN_MSIX_VECT
MSI-X vectors were allocated.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Cc: pv-drivers@vmware.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
niu: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jingoo Han <jg1.han@samsung.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
sfc: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Shradha Shah <sshah@solarflare.com> Cc: linux-net-drivers@solarflare.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Shradha Shah <sshah@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlge: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Shahed Shaikh <shahed.shaikh@qlogic.com> Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Cc: Ron Mercer <ron.mercer@qlogic.com> Cc: linux-driver@qlogic.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Rajesh Borundia <rajesh.borundia@qlogic.com> Cc: Shahed Shaikh <shahed.shaikh@qlogic.com> Cc: linux-driver@qlogic.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Manish Chopra <manish.chopra@qlogic.com> Cc: Sony Chacko <sony.chacko@qlogic.com> Cc: Rajesh Borundia <rajesh.borundia@qlogic.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
forcedeth: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
forcedeth: Cleanup MSI-X to MSI to INTx fallback code
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
forcedeth: Fix invalid errno reporting in nv_request_irq()
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Patrick McHardy <kaber@trash.net> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
vxge: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
s2io: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jon Mason <jdmason@kudzu.us> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
myri10ge: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Hyong-Youb Kim <hykim@myri.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Eli Cohen <eli@mellanox.com> Cc: linux-rdma@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Amir Vadai <amirv@mellanox.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbevf: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
igbvf: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
igb: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
i40e: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
e1000e: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Cc: e1000-devel@lists.sourceforge.net Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
benet: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Sathya Perla <sathya.perla@emulex.com> Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com> Cc: Ajit Khaparde <ajit.khaparde@emulex.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Christian Benvenuti <benve@cisco.com> Cc: Sujith Sankar <ssujith@cisco.com> Cc: Govindarajulu Varadarajan <govindarajulu90@gmail.com> Cc: Neel Patel <neepatel@cisco.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Govindarajulu Varadarajan <govindarajulu90@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4vf: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Casey Leedom <leedom@chelsio.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4vf: Remove superfluous call to pci_disable_msix()
There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Casey Leedom <leedom@chelsio.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Dimitris Michailidis <dm@chelsio.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb3: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Santosh Raspatur <santosh@chelsio.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb3: Remove superfluous call to pci_disable_msix()
There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Santosh Raspatur <santosh@chelsio.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
bna: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Rasesh Mody <rmody@brocade.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Nithin Nayak Sujir <nsujir@broadcom.com> Cc: Michael Chan <mchan@broadcom.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Ariel Elior <ariele@broadcom.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Michael Chan <mchan@broadcom.com> Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset represents the first part of an effort
to solve some old device configuration issues in gianfar,
especially run-time reset and re-configuration problems.
I'm referring to "on-the-fly" configuration of registers
against HW specification, concurrency issues during device
reset / re-configuration operations, and implementing HW
advisories for these operations.
There's also a good deal of code cleanup and refactoring,
and some other (minor) fixes as well.
v2: Remove sysfs stubs w/o replacing them with module
params (patch 2).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:19 +0000 (12:53 +0200)]
gianfar: Remove clean_rx_ring race from gfar_ethtool
gfar_clean_rx_ring() was designed to be called from napi
(rx softirq) context to do the Rx processing. Calling it
from a process context like this is a bug as it will
clearly race with the napi Rx processing.
There's also no point in initializing num_txbdfree since
startup_gfar() already does that, when bringing the device
up again (after reset). Changing num_txbdfree "on-the-fly"
like this is also subject to race conditions. num_txbdfree
is handled by the Tx processing path and the device reset
procedure. Also, don't assume that num_rx_queues is always
equal to num_tx_queues.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:18 +0000 (12:53 +0200)]
gianfar: Add missing graceful reset steps and fixes
gfar_halt() and gfar_start() are responsible for stopping
and starting the DMA and the Rx/Tx hw rings. They implement
the support for the "graceful Rx/Tx stop/start" hw procedure,
and also disable/enable eTSEC's hw interrupts in the process.
The GRS/GTS procedure requires however to have the RQUEUE/TQUEUE
registers cleared first and to wait for a period of time for the
current frame to pass through the interface (around ~10ms for a
jumbo frame). Only then may the GTS and GRS bits from DMACTRL be
set to shut down the DMA, and finally the Tx_EN and Rx_EN bits in
MACCFG1 may be cleared to disable the Tx/Rx blocks.
The same register programming order applies to start the Rx/Tx:
enabling the RQUEUE/TQUEUE *before* clearing the GRS/GTS bits.
This is a HW recommendation in order to avoid a possible
controller "lock up" during graceful reset.
Cleanup the gfar_halt()/start() prototypes, to take priv instead
of ndev as their purpose is to operate on HW. Enabling the
RQUEUE/TQUEUE in the hw_init() is not needed anymore since
that's the job of gfar_start().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:17 +0000 (12:53 +0200)]
gianfar: Factor out enabling/disabling of hw interrupts
Throughout the code there are places where the controller's
hw interrupt sources need to get disabled/enabled (masked/
un-masked) all at once. The recommendation for disabling
the interrupts is to clear the ievent first then the imask
register (not the other way around).
Use the gfar_ints_enable/disable() helpers to make these
operations consistent.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:16 +0000 (12:53 +0200)]
gianfar: Remove useless HAS_PADDING device flag
The RCTRL updates of the FSL_GIANFAR_DEV_HAS_PADDING device
flag get overriden by the FSL_GIANFAR_DEV_HAS_TIMER flag
settings, which impose a Rx padding alignment of 8 bytes.
As all the eTSEC devices that set HAS_PADDING also set the
HAS_TIMER flag, the HAS_PADDING flag is now obsolete.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:15 +0000 (12:53 +0200)]
gianfar: Remove sysfs stubs for FIFOCFG and stashing
Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI
(stashing) config registers, as these registers may only
be configured after a MAC reset, with the controller stopped
(i.e. during hw init, at probe() time). The current sysfs
stubs allow on-the-fly updates of these registers (the locking
measures are useless and only add unecessary code).
Changing these registers is discouraged. Only the default values
will be used instead.
Moreover, the stashing (ATTRELI) configuration options were
effectively disabled (didn't get to the hw anyway if changed)
because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING)
were "accidentally" cleared during probe().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Mon, 17 Feb 2014 10:53:14 +0000 (12:53 +0200)]
gianfar: Cleanup/Fix gfar_probe and the hw init code
Factor out gfar_hw_init() to contain all the controller hw
initialization steps for a better control of register writes,
and to significantly simplify the tangled code from gfar_probe().
This results in code size and stack usage reduction (besides
code readability).
Fix memory leak on device removal, by freeing the rx_/tx_queue
structures.
Replace custom bit swapping function with a library one (bitrev8).
Move allocation of rx_/tx_queue struct arrays before the group
structure init, because in order to assign Rx/Tx queues
to groups we need to have the queues first. This also allows
earlier bail out of gfar_probe(), in case the memory allocation
fails.
The flow control checks for maccfg1 were removed from gfar_probe(),
since flow control is disabled at probe time (priv->rx_/tx_pause_en
are 0). Redundant initializations (by 0) also removed.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Feb 2014 21:43:17 +0000 (16:43 -0500)]
Merge branch 'ieee802154'
Phoebe Buckheister says:
====================
ieee802154: support rf212 and extended mac features
this patch set adds support for the RF212 radio chip to the existing
at86rf230 driver and adds support for numerous features of the RF212
chips to the ieee802154 stack. These features include CSMA parameter
configuration, transmit power control, CCA parameter configuration, and
automatic retransmission of frames. Netlink APIs are provided for all
new options introduced in this set.
Many features might also work for RF230, but since I have no such chips
at my disposal, most new features are implemented only for RF212.
Changes since v2:
* Indentation
Changes since v1:
* CodingStyle compliance. Thanks Sergei Shtylyov
* Add CSMA parameters to netlink phy list that were forgotten in v1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154: enable smart transmitter features of RF212
This patch does multiple things:
* add .set_csma_params and .set_frame_retries for the RF212 radio.
This should work fine with RF230, but since I have no RF230 radios to
test with, RF230 does not implement these right now
* enable TX_ARET for frame retransmission limits greater than -1
Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The CSMA attributes shall correspond to minBE, maxBE and maxCSMABackoffs of
802.15.4, respectively. The frame retransmission shall correspond to
maxFrameRetries of 802.15.4, unless given as -1: then the old behaviour
of the stack shall apply. For RF2xy, the old behaviour is to not do
channel sensing at all and simply send *right now*, which is not
intended behaviour for most applications and actually prohibited for
some channel/page combinations.
For all values except frame retransmission limit, the defaults of
802.15.4 apply. Frame retransmission limits are set to -1 to indicate
backward-compatible behaviour.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154: ensure that first RF212 state comes from TRX_OFF
A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.
The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154: add support for setting CCA energy detection levels
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154: add support for listen-before-talk in wpan_phy
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.
Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.
Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
ieee802154: add basic support for RF212 to at86rf230 driver
Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:
* force the initial state after P_ON to FORCE_TRX_OFF to work around a
documented erratum
* channels_supported depends on the frequency of the transceiver, and
thus is_rf212
* do early detection of chip version select an appropriate _ops struct
based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Feb 2014 21:40:24 +0000 (16:40 -0500)]
Merge branch 'phy'
Florian Fainelli says:
====================
net: phy: soft reset rework for 10G PHYs
As reported by Shaohui, 10G PHYs may have a slightly more complex reset
sequence for which a BMCR_RESET software reset might not suffice. This
patchset offers a solution for those by allowing them to implement their
own soft_reset() callback. Finally there is an update to the PHY library
Documentation to cover for the newly added callbacks of the PHY driver
structure.
Changes in v2:
- fixed callback testing
- fixed typo in Documentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 17 Feb 2014 21:34:03 +0000 (13:34 -0800)]
net: phy: allow PHY drivers to implement their own software reset
As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 17 Feb 2014 21:34:02 +0000 (13:34 -0800)]
net: phy: move PHY software reset to genphy_soft_reset
As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.
Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Mon, 17 Feb 2014 00:38:44 +0000 (16:38 -0800)]
Drivers: net: hyperv: Cleanup the receive path
Make the receive path a little more efficient by parameterizing the
required state rather than re-establishing that state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KY Srinivasan [Mon, 17 Feb 2014 00:38:43 +0000 (16:38 -0800)]
Drivers: net: hyperv: Get rid of the rndis_filter_packet structure
This structure is redundant; get rid of it make the code little more efficient -
get rid of the unnecessary indirection.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Sørensen [Sun, 16 Feb 2014 13:54:25 +0000 (14:54 +0100)]
net:cpsw: Pass unhandled ioctl's on to generic phy ioctl
This patch allows the use of a generic timestamping phy connected
to the cpsw if CPTS support is not enabled. This also adds support
of the SIOCGMIIREG and SIOCSMIIREG, and moves handling of SIOCGMIIPHY
to the generic driver.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Reviewed-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sun, 16 Feb 2014 00:01:45 +0000 (16:01 -0800)]
bonding: Neaten pr_<level>
Add missing terminating newlines.
Convert uses of pr_info to pr_cont in bond_check_params.
Standardize upper/lower case styles.
Typo fixes, remove unnecessary parentheses and periods.
Alignment neatening.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sat, 15 Feb 2014 07:36:13 +0000 (08:36 +0100)]
caif: delete unnecessary field initialization
On success, the function netdev_alloc_skb initializes the dev field of its
result to its first argument, so this doesn't have to be done in the
calling context.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression skb,privn,e;
@@
skb = netdev_alloc_skb(privn,...);
... when strict
(
-skb->dev = privn;
|
?skb = e
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Document the required "clocks" phandles and their corresponding
"clock-names" properties for the two clocks used by the GENET hardware
block ("enet" and "enet-wol").
CC: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-kernels.git / log