John Hurley [Wed, 16 Jan 2019 03:06:58 +0000 (19:06 -0800)]
nfp: flower: ensure MAC cleanup on address change
It is possible to receive a MAC address change notification without the
net device being down (e.g. when an OvS bridge is assigned the same MAC as
a port added to it). This means that an offloaded MAC address may not be
removed if its device gets a new address.
Maintain a record of the offloaded MAC addresses for each repr and netdev
assigned a MAC offload index. Use this to delete the (now expired) MAC if
a change of address event occurs. Only handle change address events if the
device is already up - if not then the netdev up event will handle it.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Wed, 16 Jan 2019 03:06:57 +0000 (19:06 -0800)]
nfp: flower: add infastructure for non-repr priv data
NFP repr netdevs contain private data that can store per port information.
In certain cases, the NFP driver offloads information from non-repr ports
(e.g. tunnel ports). As the driver does not have control over non-repr
netdevs, it cannot add/track private data directly to the netdev struct.
Add infastructure to store private information on any non-repr netdev that
is offloaded at a given time. This is used in a following patch to track
offloaded MAC addresses for non-reprs and enable correct house keeping on
address changes.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Wed, 16 Jan 2019 03:06:56 +0000 (19:06 -0800)]
nfp: flower: ensure deletion of old offloaded MACs
When a potential tunnel end point goes down then its MAC address should
not be matchable on the NFP.
Implement a delete message for offloaded MACs and call this on net device
down. While at it, remove the actions on register and unregister netdev
events. A MAC should only be offloaded if the device is up. Note that the
netdev notifier will replay any notifications for UP devices on
registration so NFP can still offload ports that exist before the driver
is loaded. Similarly, devices need to go down before they can be
unregistered so removal of offloaded MACs is only required on down events.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Wed, 16 Jan 2019 03:06:55 +0000 (19:06 -0800)]
nfp: flower: remove list infastructure from MAC offload
Potential MAC destination addresses for tunnel end-points are offloaded to
firmware. This was done by building a list of such MACs and writing to
firmware as blocks of addresses.
Simplify this code by removing the list format and sending a new message
for each offloaded MAC.
This is in preparation for delete MAC messages. There will be one delete
flag per message so we cannot assume that this applies to all addresses
in a list.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Wed, 16 Jan 2019 03:06:54 +0000 (19:06 -0800)]
nfp: flower: ignore offload of VF and PF repr MAC addresses
Currently MAC addresses of all repr netdevs, along with selected non-NFP
controlled netdevs, are offloaded to FW as potential tunnel end-points.
However, the addresses of VF and PF reprs are meaningless outside of
internal communication and it is only those of physical port reprs
required.
Modify the MAC address offload selection code to ignore VF/PF repr devs.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Wed, 16 Jan 2019 03:06:53 +0000 (19:06 -0800)]
nfp: flower: tidy tunnel related private data
Recent additions to the flower app private data have grouped the variables
of a given feature into a struct and added that struct to the main private
data struct.
In keeping with this, move all tunnel related private data to their own
struct. This has no affect on functionality but improves readability and
maintenance of the code.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: flower: support multiple memory units for filter offloads
Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fred Lotter [Wed, 16 Jan 2019 03:06:51 +0000 (19:06 -0800)]
nfp: flower: increase cmesg reply timeout
QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.
Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix over 100 documentation warnings in snmp_counter.rst by
extending the underline string lengths and inserting a blank line
after bullet items.
Examples:
Documentation/networking/snmp_counter.rst:1: WARNING: Title overline too short.
Documentation/networking/snmp_counter.rst:14: WARNING: Bullet list ends without a blank line; unexpected unindent.
Fixes: 2b96547223e3 ("add document for TCP OFO, PAWS and skip ACK counters") Fixes: 8e2ea53a83df ("add snmp counters document") Fixes: 712ee16c230f ("add documents for snmp counters") Fixes: 80cc49507ba4 ("net: Add part of TCP counts explanations in snmp_counters.rst") Fixes: b08794a922c4 ("documentation of some IP/ICMP snmp counters") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: yupeng <yupeng0921@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
mlxsw: spectrum_nve: Use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_acl_bloom_filter: use struct_size() in kzalloc()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
This issue was detected with the help of Coccinelle.
Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: dsa: ksz9477: fix indentation for switch spi bindings
Switch bindings for spi managed mode are using spaces instead of tabs.
Fix them to get a file with a proper kernel indentation style.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 15 Jan 2019 23:48:00 +0000 (15:48 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-01-15
This series contains updates to the ice driver only.
Bruce fixes an unused variable build warning, which was introduced with
the commit 2fd527b72bb6 ("net: ndo_bridge_setlink: Add extack"). Added
ethtool support for get_eeprom and get_eeprom_len operations. Added
support for bringing down the PHY link optional when the interface is
administratively downed.
Anirudh refactors the transmit scheduler functions, which results in
reduced code duplication and adds a helper function, which all the
scheduler functions call instead. Added an LED blinking handler to
ethtool. Reworked the queue management code to allow for reuse in
future XDP feature support. Updates the driver to be able to preserve
the aggregator list after reset by moving it out of port_info and into
ice_hw. Added the ability to offload SCTP checksum calculation to the
hardware. Added support for new PHY types, which support higher link
speeds.
Md Fahad makes sure that RSS lookup table and hash key get configured
during the rebuild path after a reset.
Brett updates the driver to set the physical link state according to the
netdev state (up/down). Added support for adaptive/dynamic interrupt
moderation in the ice driver, along with the ethtool operations needed.
Tony adds software timestamping support by using
ethtool_op_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 19 Dec 2018 18:03:34 +0000 (10:03 -0800)]
ice: add const qualifier to mac_addr parameter
The function ice_aq_manage_mac_write takes a pointer to a MAC address.
The parameter is not marked const, even though the function doesn't need
to modify it. This prevents passing a parameter that is already marked
const. Update the function prototype to take a const pointer, to allow
passing constant pointers to this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Each ITR value (current_itr/target_itr) are stored on a per
ice_ring_container basis. This is because each valid ice_ring_container
can have 1 or more rings that are tied to the same q_vector ITR index.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Wed, 19 Dec 2018 18:03:29 +0000 (10:03 -0800)]
ice: Add support for adaptive interrupt moderation
Currently the driver does not support adaptive/dynamic interrupt
moderation. This patch adds support for this. Also, adaptive/dynamic
interrupt moderation is turned on by default upon driver load.
In order to support adaptive interrupt moderation, two functions were
added, ice_update_itr() and ice_itr_divisor(). These are used to
determine the current packet load and to determine a divisor based
on link speed respectively.
This patch also adds the ICE_ITR_GRAN_S define that is used in the
hot-path when setting a new ITR value. The shift is used to pet two
birds with one hand, set the ITR value while re-enabling the
interrupt. Also, the ICE_ITR_GRAN_S is defined as 1 because the device
has a ITR granularity of 2usecs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 19 Dec 2018 18:03:26 +0000 (10:03 -0800)]
ice: Add ethtool private flag to make forcing link down optional
Add new infrastructure for implementing ethtool private flags using the
existing pf->flags bitmap to store them, and add the link-down-on-close
ethtool private flag to optionally bring down the PHY link when the
interface is administratively downed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Wed, 19 Dec 2018 18:03:25 +0000 (10:03 -0800)]
ice: Set physical link up/down when an interface is set up/down
When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.
In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Wed, 19 Dec 2018 18:03:24 +0000 (10:03 -0800)]
ice: Implement support for normal get_eeprom[_len] ethtool ops
Add support for get_eeprom and get_eeprom_len ethtool ops
Specification states that PF software accesses NVM (shadow-ram) via AQ
commands (e.g. NVM Read, NVM Write) in the range 0x000000-0x00FFFF (64KB),
so the get_eeprom_len op should return 64KB. If additional regions of the
16MB NVM must be read, another access method must be used.
The ethtool kernel code, by default, will ask for multiple page-size hunks
of the NVM not to exceed the value returned by ice_get_eeprom_len().
ice_read_sr_buf() deals with arch page sizes different than 4KB.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Tue, 15 Jan 2019 17:28:26 +0000 (05:28 +1200)]
Merge tag 'trace-v5.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Andrea Righi fixed a NULL pointer dereference in trace_kprobe_create()
It is possible to trigger a NULL pointer dereference by writing an
incorrectly formatted string to the krpobe_events file"
* tag 'trace-v5.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Fix NULL pointer dereference in trace_kprobe_create()
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
Bruce Allan [Wed, 19 Dec 2018 18:03:20 +0000 (10:03 -0800)]
ice: Fix unused variable build warning
Commit 2fd527b72bb6 ("net: ndo_bridge_setlink: Add extack") added a new
parameter "extack" to ice_bridge_setlink but this parameter isn't used
by the function. This results in a warning: unused parameter ‘extack’
[-Wunused-parameter]. Fix that by adding an "__always_unused" qualifier.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Andrea Righi [Fri, 11 Jan 2019 06:01:13 +0000 (07:01 +0100)]
tracing/kprobes: Fix NULL pointer dereference in trace_kprobe_create()
It is possible to trigger a NULL pointer dereference by writing an
incorrectly formatted string to krpobe_events (trying to create a
kretprobe omitting the symbol).
Ming Lei [Tue, 15 Jan 2019 03:59:52 +0000 (11:59 +0800)]
sbitmap: Protect swap_lock from hardirq
Because we may call blk_mq_get_driver_tag() directly from
blk_mq_dispatch_rq_list() without holding any lock, then HARDIRQ may
come and the above DEADLOCK is triggered.
Commit ab53dcfb3e7b ("sbitmap: Protect swap_lock from hardirq") tries to
fix this issue by using 'spin_lock_bh', which isn't enough because we
complete request from hardirq context direclty in case of multiqueue.
Cc: Clark Williams <williams@redhat.com> Fixes: ab53dcfb3e7b ("sbitmap: Protect swap_lock from hardirq") Cc: Jens Axboe <axboe@kernel.dk> Cc: Ming Lei <ming.lei@redhat.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 14 Jan 2019 18:26:28 +0000 (06:26 +1200)]
Merge tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"The patch hitting the MMC/SD subsystem is fixing up my own mess when
moving semantics from MMC/SD over to gpiolib. Ulf is on vacation but I
managed to reach him on chat and obtain his ACK.
The other two are early-rc fixes that are not super serious but pretty
annoying so I'd like to get rid of them.
Summary:
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection"
* tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
mmc: core: don't override the CD GPIO level when "cd-inverted" is set
gpio: pca953x: Make symbol 'pca953x_i2c_regmap' static
gpiolib-acpi: Remove unnecessary WARN_ON from acpi_gpiochip_free_interrupts
Linus Torvalds [Mon, 14 Jan 2019 18:24:36 +0000 (06:24 +1200)]
Merge tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
Linus Torvalds [Mon, 14 Jan 2019 18:21:10 +0000 (06:21 +1200)]
Merge tag 'backlight-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Fix-ups:
- Use new of_node_name_eq() API call
Bug Fixes:
- Internally track 'enabled' state in pwm_bl
- Fix auto-generated pwm_bl brightness tables parsed by DT
* tag 'backlight-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: 88pm860x_bl: Use of_node_name_eq for node name comparisons
backlight: pwm_bl: Fix devicetree parsing with auto-generated brightness tables
backlight: pwm_bl: Re-add driver internal enabled tracking
kernel/sys.c: Clarify that UNAME26 does not generate unique versions anymore
UNAME26 is a mechanism to report Linux's version as 2.6.x, for
compatibility with old/broken software. Due to the way it is
implemented, it would have to be updated after 5.0, to keep the
resulting versions unique. Linus Torvalds argued:
"Do we actually need this?
I'd rather let it bitrot, and just let it return random versions. It
will just start again at 2.4.60, won't it?
Anybody who uses UNAME26 for a 5.x kernel might as well think it's
still 4.x. The user space is so old that it can't possibly care about
differences between 4.x and 5.x, can it?
The only thing that matters is that it shows "2.4.<largeenough>",
which it will do regardless"
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 13 Jan 2019 22:34:14 +0000 (10:34 +1200)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bigger batch than I anticipated this week, for two reasons:
- Some fallout on Davinci from board file -> DTB conversion, that
also includes a few longer-standing fixes (i.e. not recent
regressions).
- drivers/reset material that has been in linux-next for a while, but
didn't get sent to us until now for a variety of reasons
(maintainer out sick, holidays, etc). There's a functional
dependency in there such that one platform (Altera's SoCFPGA) won't
boot without one of the patches; instead of reverting the patch
that got merged, I looked at this set and decided it was small
enough that I'll pick it up anyway. If you disagree I can revisit
with a smaller set.
That being said, there's also a handful of the usual stuff:
- Fix for a crash on Armada 7K/8K when the kernel touches
PSCI-reserved memory
- Fix for PCIe reset on Macchiatobin (Armada 8K development board,
what this email is sent from in fact :)
- Enable a few new-merged modules for Amlogic in arm64 defconfig
- Error path fixes on Integrator
- Build fix for Renesas and Qualcomm
- Initialization fix for Renesas RZ/G2E
.. plus a few more fixlets"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: integrator: impd1: use struct_size() in devm_kzalloc()
qcom-scm: Include <linux/err.h> header
gpio: pl061: handle failed allocations
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
ARM: dts: da850-lcdk: Correct the sound card name
ARM: dts: da850-lcdk: Correct the audio codec regulators
ARM: dts: da850-evm: Correct the sound card name
ARM: dts: da850-evm: Correct the audio codec regulators
ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
ARM: davinci: da850-evm: fix label names in GPIO lookup entries
ARM: davinci: da830-evm: fix label names in GPIO lookup entries
arm64: defconfig: enable modules for amlogic s400 sound card
reset: uniphier-glue: Add AHCI reset control support in glue layer
dt-bindings: reset: uniphier: Add AHCI core reset description
reset: uniphier-usb3: Rename to reset-uniphier-glue
dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
...
Linus Torvalds [Sun, 13 Jan 2019 17:55:51 +0000 (05:55 +1200)]
Merge tag 'for-5.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- two regression fixes in clone/dedupe ioctls, the generic check
callback needs to lock extents properly and wait for io to avoid
problems with writeback and relocation
- fix deadlock when using free space tree due to block group creation
- a recently added check refuses a valid fileystem with seeding device,
make that work again with a quickfix, proper solution needs more
intrusive changes
* tag 'for-5.0-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Use real device structure to verify dev extent
Btrfs: fix deadlock when using free space tree due to block group creation
Btrfs: fix race between reflink/dedupe and relocation
Btrfs: fix race between cloning range ending at eof and writeback
Linus Torvalds [Sun, 13 Jan 2019 17:51:08 +0000 (05:51 +1200)]
Merge tag 'driver-core-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here is one small sysfs change, and a documentation update for 5.0-rc2
The sysfs change moves from using BUG_ON to WARN_ON, as discussed in
an email thread on lkml while trying to track down another driver bug.
sysfs should not be crashing and preventing people from seeing where
they went wrong. Now it properly recovers and warns the developer.
The documentation update removes the use of BUS_ATTR() as the kernel
is moving away from this to use the specific BUS_ATTR_RW() and friends
instead. There are pending patches in all of the different subsystems
to remove the last users of this macro, but for now, don't advertise
it should be used anymore to keep new ones from being introduced.
Both have been in linux-next with no reported issues"
* tag 'driver-core-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation: driver core: remove use of BUS_ATTR
sysfs: convert BUG_ON to WARN_ON
Linus Torvalds [Sun, 13 Jan 2019 17:49:35 +0000 (05:49 +1200)]
Merge tag 'staging-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for some reported issues.
One reverts a patch that was made to the rtl8723bs driver that turned
out to not be needed at all as it was a bug in clang. The others fix
up some reported issues in the rtl8188eu driver and update the
MAINTAINERS file to point to Larry for this driver so he can get the
bug reports easier.
All have been in linux-next with no reported issues"
* tag 'staging-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "staging: rtl8723bs: Mark ACPI table declaration as used"
staging: rtl8188eu: Fix module loading from tasklet for WEP encryption
staging: rtl8188eu: Fix module loading from tasklet for CCMP encryption
MAINTAINERS: Add entry for staging driver r8188eu
Linus Torvalds [Sun, 13 Jan 2019 17:47:48 +0000 (05:47 +1200)]
Merge tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed
up in 5.0-rc1. The second one resolves a number of reported issues
with the recent tty locking fixes that went into 5.0-rc1. Lots of
people have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues"
* tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Don't hold ldisc lock in tty_reopen() if ldisc present
serial: lantiq: Do not swap register read/writes
Linus Torvalds [Sun, 13 Jan 2019 17:45:28 +0000 (05:45 +1200)]
Merge tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues"
* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: storage: Remove outdated URL from MAINTAINERS
USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
usbcore: Select only first configuration for non-UAC3 compliant devices
USB: storage: add quirk for SMI SM3350
USB: storage: don't insert sane sense for SPC3+ when bad sense specified
usb: cdc-acm: send ZLP for Telit 3G Intel based modems
Linus Torvalds [Sun, 13 Jan 2019 17:43:40 +0000 (05:43 +1200)]
Merge tag '5.0-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A set of cifs/smb3 fixes, 4 for stable, most from Pavel. His patches
fix an important set of crediting (flow control) problems, and also
two problems in cifs_writepages, ddressing some large i/o and also
compounding issues"
* tag '5.0-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
CIFS: Fix error paths in writeback code
CIFS: Move credit processing to mid callbacks for SMB3
CIFS: Fix credits calculation for cancelled requests
cifs: Fix potential OOB access of lock element array
cifs: Limit memory used by lock request calls to a page
cifs: move large array from stack to heap
CIFS: Do not hide EINTR after sending network packets
CIFS: Fix credit computation for compounded requests
CIFS: Do not set credits to 1 if the server didn't grant anything
CIFS: Fix adjustment of credits for MTU requests
cifs: Fix a tiny potential memory leak
cifs: Fix a debug message
Olof Johansson [Sun, 13 Jan 2019 06:06:54 +0000 (22:06 -0800)]
Merge tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux into fixes
Late reset controller changes for v5.0
This adds missing deassert functionality to the ARC HSDK reset driver,
fixes some indentation and grammar issues in the kernel docs, adds a
helper to count the number of resets on a device for the non-DT case
as well, adds an early reset driver for SoCFPGA and simple reset driver
support for Stratix10, and generalizes the uniphier USB3 glue layer
reset to also cover AHCI.
* tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier-glue: Add AHCI reset control support in glue layer
dt-bindings: reset: uniphier: Add AHCI core reset description
reset: uniphier-usb3: Rename to reset-uniphier-glue
dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
ARM: socfpga: dts: document "altr,stratix10-rst-mgr" binding
reset: socfpga: add an early reset driver for SoCFPGA
reset: fix null pointer dereference on dev by dev_name
reset: Add reset_control_get_count()
reset: Improve reset controller kernel docs
ARC: HSDK: improve reset driver
Olof Johansson [Sun, 13 Jan 2019 06:03:59 +0000 (22:03 -0800)]
Merge tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Olof Johansson [Sun, 13 Jan 2019 06:03:18 +0000 (22:03 -0800)]
Merge tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into fixes
Fixes for the Integrator:
- Handle failed allocations in the IM/PC bus attachment.
- Use struct_size() for allocation.
* tag 'integrator-fixes-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: impd1: use struct_size() in devm_kzalloc()
gpio: pl061: handle failed allocations
Olof Johansson [Sun, 13 Jan 2019 06:02:28 +0000 (22:02 -0800)]
Merge tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic DT fixes for v5.0-rc
- arm64: defconfig: enable modules for amlogic s400 sound card
* tag 'amlogic-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: defconfig: enable modules for amlogic s400 sound card
Olof Johansson [Sun, 13 Jan 2019 06:00:36 +0000 (22:00 -0800)]
Merge tag 'davinci-fixes-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
This pull request fixes some more regressions on legacy
DaVinci board support due to GPIO driver clean-up introduced
in v4.20 kernel. These are marked for stable.
Also has fixes for some long standing Audio issues on DA850
boards.
* tag 'davinci-fixes-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lcdk: Correct the sound card name
ARM: dts: da850-lcdk: Correct the audio codec regulators
ARM: dts: da850-evm: Correct the sound card name
ARM: dts: da850-evm: Correct the audio codec regulators
ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
ARM: davinci: da850-evm: fix label names in GPIO lookup entries
ARM: davinci: da830-evm: fix label names in GPIO lookup entries
Olof Johansson [Sun, 13 Jan 2019 05:59:42 +0000 (21:59 -0800)]
Merge tag 'renesas-fixes-for-v5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v5.0
Renesas SoCs:
* Fix build regressions caused by move of Kconfig symbols
RZ/G2E (r8a774c0) SoC:
* Correct initialization order of 3DG-{A,B} in SYSC driver
* tag 'renesas-fixes-for-v5.0' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: r8a774c0-sysc: Fix initialization order of 3DG-{A,B}
ARM: shmobile: fix build regressions
John Hubbard [Sun, 13 Jan 2019 01:29:09 +0000 (17:29 -0800)]
phy: fix build breakage: add PHY_MODE_SATA
Commit 49e54187ae0b ("ata: libahci_platform: comply to PHY framework") uses
the PHY_MODE_SATA, but that enum had not yet been added. This caused a
build failure for me, with today's linux.git.
Also, there is a potentially conflicting (mis-named) PHY_MODE_SATA, hiding
in the Marvell Berlin SATA PHY driver.
Fix the build by:
1) Renaming Marvell's defined value to a more scoped name,
in order to avoid any potential conflicts: PHY_BERLIN_MODE_SATA.
2) Adding the missing enum, which was going to be added anyway as part
of [1].
- ahch mvebu suspend/resume support. Should have gone into the merge
window, but there was some confusion on which tree had it. (Miquel)
* tag 'for-linus-20190112' of git://git.kernel.dk/linux-block: (22 commits)
ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
ata: ahci: mvebu: remove stale comment
ata: libahci_platform: comply to PHY framework
loop: drop caches if offset or block_size are changed
block: fix kerneldoc comment for blk_attempt_plug_merge()
nvme: don't initlialize ctrl->cntlid twice
nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
nvme: pad fake subsys NQN vid and ssvid with zeros
nvme-multipath: zero out ANA log buffer
nvme-fabrics: unset write/poll queues for discovery controllers
nvme-tcp: don't ask if controller is fabrics
nvme-tcp: remove dead code
nvme-pci: fix out of bounds access in nvme_cqe_pending
nvme-pci: rerun irq setup on IO queue init errors
nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
nvme-pci: fix the wrong setting of nr_maps
block: doc: add slice_idle_us to bfq documentation
block: clarify documentation for blk_{start|finish}_plug
...
Linus Torvalds [Sat, 12 Jan 2019 18:52:40 +0000 (10:52 -0800)]
Merge tag 'remove-dma_zalloc_coherent-5.0' of git://git.infradead.org/users/hch/dma-mapping
Pull dma_zalloc_coherent() removal from Christoph Hellwig:
"We've always had a weird situation around dma_zalloc_coherent. To
safely support mapping the allocations to userspace major
architectures like x86 and arm have always zeroed allocations from
dma_alloc_coherent, but a couple other architectures were missing that
zeroing either always or in corner cases.
Then later we grew anothe dma_zalloc_coherent interface to explicitly
request zeroing, but that just added __GFP_ZERO to the allocation
flags, which for some allocators that didn't end up using the page
allocator ended up being a no-op and still not zeroing the
allocations.
So for this merge window I fixed up all remaining architectures to
zero the memory in dma_alloc_coherent, and made dma_zalloc_coherent a
no-op wrapper around dma_alloc_coherent, which fixes all of the above
issues.
dma_zalloc_coherent is now pointless and can go away, and Luis helped
me writing a cocchinelle script and patch series to kill it, which I
think we should apply now just after -rc1 to finally settle these
issue"
* tag 'remove-dma_zalloc_coherent-5.0' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: remove dma_zalloc_coherent()
cross-tree: phase out dma_zalloc_coherent() on headers
cross-tree: phase out dma_zalloc_coherent()
Michael Chan [Sat, 12 Jan 2019 05:13:05 +0000 (00:13 -0500)]
bnxt_en: Fix context memory allocation.
When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk(). This will cause the last page table
to be completely blank and causing some RDMA failures.
Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.
Fixes: 08fe9d181606 ("bnxt_en: Add Level 2 context memory paging support.") Reported-by: Eric Davis <eric.davis@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 12 Jan 2019 05:13:04 +0000 (00:13 -0500)]
bnxt_en: Fix ring checking logic on 57500 chips.
In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources. Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs. This issue shows up when adding MQPRIO TX queues, for example.
Fixes: 36d65be9a880 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 12 Jan 2019 18:39:43 +0000 (10:39 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"Minor fixes for new code, corner cases, and documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/kvm/nVMX: don't skip emulated instruction twice when vmptr address is not backed
Documentation/virtual/kvm: Update URL for AMD SEV API specification
KVM/VMX: Avoid return error when flush tlb successfully in the hv_remote_flush_tlb_with_range()
kvm: sev: Fail KVM_SEV_INIT if already initialized
KVM: validate userspace input in kvm_clear_dirty_log_protect()
KVM: x86: Fix bit shifting in update_intel_pt_cfg
Linus Torvalds [Sat, 12 Jan 2019 18:30:43 +0000 (10:30 -0800)]
Merge tag 'drm-fixes-2019-01-11-1' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Daniel Vetter:
"Dave sends out his pull, everybody remembers holidays are over :-)
Since Dave's already in weekend mode and it was quite a few patches I
figured better to apply all the pulls and forward them to you. Hence
here 2nd part of bugfixes for -rc2.
i915:
- Disable PSR for Apple panels
- Broxton ERR_PTR error state fix
- Kabylake VECS workaround fix
- Unwind failure on pinning the gen7 ppgtt
- GVT workload request allocation fix
core:
- Fix fb-helper to work correctly with SDL 1.2 bugs
- Fix lockdep warning in the atomic ioctl and setproperty"
* tag 'drm-fixes-2019-01-11-1' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/falcon: avoid touching registers if engine is off
drm/nouveau: Don't disable polling in fallback mode
drm/nouveau: register backlight on pascal and newer
drm: Fix documentation generation for DP_DPCD_QUIRK_NO_PSR
drm/i915: init per-engine WAs for all engines
drm/i915: Unwind failure on pinning the gen7 ppgtt
drm/i915: Skip the ERR_PTR error state
drm/i915: Disable PSR in Apple panels
gpu/drm: Fix lock held when returning to user space.
drm/fb-helper: Ignore the value of fb_var_screeninfo.pixclock
drm/fb-helper: Partially bring back workaround for bugs of SDL 1.2
drm/i915/gvt: Fix workload request allocation before request add
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
Paolo Abeni [Tue, 8 Jan 2019 17:45:05 +0000 (18:45 +0100)]
net: clear skb->tstamp in bridge forwarding path
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844d3 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.") Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Reported-and-tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 12 Jan 2019 02:05:41 +0000 (18:05 -0800)]
Merge branch 'bpfilter-fixes'
Taehee Yoo says:
====================
net: bpfilter: fix two bugs in bpfilter
This patches fix two bugs in the bpfilter_umh which are related in
iptables command.
The first patch adds an exit code for UMH process.
This provides an opportunity to cleanup members of the umh_info
to modules which use the UMH.
In order to identify UMH processes, a new flag PF_UMH is added.
The second patch makes the bpfilter_umh use UMH cleanup callback.
The third patch adds re-start routine for the bpfilter_umh.
The bpfilter_umh does not re-start after error occurred.
because there is no re-start routine in the module.
The fourth patch ensures that the bpfilter.ko module will not removed while
it's being used.
The bpfilter.ko is not protected by locks or module reference counter.
Therefore that can be removed while module is being used.
In order to protect that, mutex is used.
The first and second patch are preparation patches for the third and
fourth patch.
TEST #1
while :
do
modprobe bpfilter
kill -9 <pid of the bpfilter_umh>
iptables -vnL
done
TEST #2
while :
do
iptables -I FORWARD -m string --string ap --algo kmp &
iptables -F &
modprobe -rv bpfilter &
done
TEST #3
while :
do
modprobe bpfilter &
modprobe -rv bpfilter &
done
The TEST1 makes a failure of iptables command.
This is fixed by the third patch.
The TEST2 makes a panic because of a race condition in the bpfilter_umh
module.
This is fixed by the fourth patch.
The TEST3 makes a double-create UMH process.
This is fixed by the third and fourth patch.
v4 :
- declare the exit_umh() as static inline
- check stop flag in the load_umh() to avoid a double-create UMH
v3 :
- Avoid unnecessary list lookup for non-UMH processes
- Add a new PF_UMH flag
v2 : add the first and second patch
v1 : Initial patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Tue, 8 Jan 2019 17:25:10 +0000 (02:25 +0900)]
net: bpfilter: disallow to remove bpfilter module while being used
The bpfilter.ko module can be removed while functions of the bpfilter.ko
are executing. so panic can occurred. in order to protect that, locks can
be used. a bpfilter_lock protects routines in the
__bpfilter_process_sockopt() but it's not enough because __exit routine
can be executed concurrently.
Now, the bpfilter_umh can not run in parallel.
So, the module do not removed while it's being used and it do not
double-create UMH process.
The members of the umh_info and the bpfilter_umh_ops are protected by
the bpfilter_umh_ops.lock.
test commands:
while :
do
iptables -I FORWARD -m string --string ap --algo kmp &
modprobe -rv bpfilter &
done
Fixes: d2ba09c17a06 ("net: add skeleton of bpfilter kernel module") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Tue, 8 Jan 2019 17:24:53 +0000 (02:24 +0900)]
net: bpfilter: restart bpfilter_umh when error occurred
The bpfilter_umh will be stopped via __stop_umh() when the bpfilter
error occurred.
The bpfilter_umh() couldn't start again because there is no restart
routine.
The section of the bpfilter_umh_{start/end} is no longer .init.rodata
because these area should be reused in the restart routine. hence
the section name is changed to .bpfilter_umh.
The bpfilter_ops->start() is restart callback. it will be called when
bpfilter_umh is stopped.
The stop bit means bpfilter_umh is stopped. this bit is set by both
start and stop routine.
Before this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
[ 480.045136] bpfilter: write fail -32
$ iptables -vnL
All iptables commands will fail.
After this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
$ iptables -vnL
Now, all iptables commands will work.
Fixes: d2ba09c17a06 ("net: add skeleton of bpfilter kernel module") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Tue, 8 Jan 2019 17:24:34 +0000 (02:24 +0900)]
net: bpfilter: use cleanup callback to release umh_info
Now, UMH process is killed, do_exit() calls the umh_info->cleanup callback
to release members of the umh_info.
This patch makes bpfilter_umh's cleanup routine to use the
umh_info->cleanup callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Tue, 8 Jan 2019 17:23:56 +0000 (02:23 +0900)]
umh: add exit routine for UMH process
A UMH process which is created by the fork_usermode_blob() such as
bpfilter needs to release members of the umh_info when process is
terminated.
But the do_exit() does not release members of the umh_info. hence module
which uses UMH needs own code to detect whether UMH process is
terminated or not.
But this implementation needs extra code for checking the status of
UMH process. it eventually makes the code more complex.
The new PF_UMH flag is added and it is used to identify UMH processes.
The exit_umh() does not release members of the umh_info.
Hence umh_info->cleanup callback should release both members of the
umh_info and the private data.
Suggested-by: David S. Miller <davem@davemloft.net> Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jia-Ju Bai [Tue, 8 Jan 2019 13:04:48 +0000 (21:04 +0800)]
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
The functions isdn_tty_tiocmset() and isdn_tty_set_termios() may be
concurrently executed.
isdn_tty_tiocmset
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
isdn_tty_set_termios
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
Thus, some concurrency double-free bugs may occur.
These possible bugs are found by a static tool written by myself and
my manual code review.
To fix these possible bugs, the mutex lock "modem_info_mutex" used in
isdn_tty_tiocmset() is added in isdn_tty_set_termios().
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The vsock core only supports 32bit CID, but the Virtio-vsock spec define
CID (dst_cid and src_cid) as u64 and the upper 32bits is reserved as
zero. This inconsistency causes one bug in vhost vsock driver. The
scenarios is:
0. A hash table (vhost_vsock_hash) is used to map an CID to a vsock
object. And hash_min() is used to compute the hash key. hash_min() is
defined as:
(sizeof(val) <= 4 ? hash_32(val, bits) : hash_long(val, bits)).
That means the hash algorithm has dependency on the size of macro
argument 'val'.
0. In function vhost_vsock_set_cid(), a 64bit CID is passed to
hash_min() to compute the hash key when inserting a vsock object into
the hash table.
0. In function vhost_vsock_get(), a 32bit CID is passed to hash_min()
to compute the hash key when looking up a vsock for an CID.
Because the different size of the CID, hash_min() returns different hash
key, thus fails to look up the vsock object for an CID.
To fix this bug, we keep CID as u64 in the IOCTLs and virtio message
headers, but explicitly convert u64 to u32 when deal with the hash table
and vsock core.
Fixes: 834e772c8db0 ("vhost/vsock: fix use-after-free in network stack callers") Link: https://github.com/stefanha/virtio/blob/vsock/trunk/content.tex Signed-off-by: Zha Bin <zhabin@linux.alibaba.com> Reviewed-by: Liu Jiang <gerry@linux.alibaba.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 9 Jan 2019 09:06:00 +0000 (10:06 +0100)]
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.
This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.
Let's give always the same budget for RX and TX clean.
While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.
Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 9 Jan 2019 09:05:59 +0000 (10:05 +0100)]
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.
Fix this by checking earlier if user wants Watchdog disabled or not.
Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 9 Jan 2019 09:05:58 +0000 (10:05 +0100)]
net: stmmac: Check if CBS is supported before configuring
Check if CBS is currently supported before trying to configure it in HW.
Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 9 Jan 2019 09:05:57 +0000 (10:05 +0100)]
net: stmmac: dwxgmac2: Only clear interrupts that are active
In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.
Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 9 Jan 2019 09:05:56 +0000 (10:05 +0100)]
net: stmmac: Fix PCI module removal leak
Since commit b7d0f08e9129, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.
Fix this by manually unmapping regions on remove callback.
Changes from v1:
- Fix build error
Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Fixes: b7d0f08e9129 ("net: stmmac: Fix WoL for PCI-based setups") Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Miquel Raynal [Tue, 4 Dec 2018 19:28:29 +0000 (20:28 +0100)]
ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
A feature has been added in the libahci driver: the possibility to set
a new flag in hpriv->flags to let the core handle PHY suspend/resume
automatically. Make use of this feature to make suspend to RAM work
with SATA drives on A3700.
Miquel Raynal [Tue, 4 Dec 2018 19:28:28 +0000 (20:28 +0100)]
ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.
While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.
Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.
The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Miquel Raynal [Tue, 4 Dec 2018 19:28:27 +0000 (20:28 +0100)]
ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b63bd ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.
Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.
Fixes: 15d3ce7b63bd ("ata: ahci_mvebu: add support for Armada 3700 variant") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Miquel Raynal [Tue, 4 Dec 2018 19:28:26 +0000 (20:28 +0100)]
ata: ahci: mvebu: remove stale comment
For Armada-38x (32-bit) SoCs, PM platform support has been added since:
commit 32f9494c9dfd ("ARM: mvebu: prepare pm-board.c for the
introduction of Armada 38x support")
commit 3cbd6a6ca81c ("ARM: mvebu: Add standby support")
For Armada 64-bit SoCs, like the A3700 also using this AHCI driver, PM
platform support has always existed.
There are even suspend/resume hooks in this driver since:
commit d6ecf15814888 ("ata: ahci_mvebu: add suspend/resume support")
Remove the stale comment at the end of this driver stating that all
the above does not exist yet.
Miquel Raynal [Tue, 4 Dec 2018 19:28:25 +0000 (20:28 +0100)]
ata: libahci_platform: comply to PHY framework
Current implementation of the libahci does not take into account the
new PHY framework. Correct the situation by adding a call to
phy_set_mode() before phy_power_on().
PHYs should also be handled at suspend/resume time. For this, call
ahci_platform_enable/disable_phys() at suspend/resume_host() time. These
calls are guarded by a HFLAG (AHCI_HFLAG_SUSPEND_PHYS) that the user of
the libahci driver must set manually in hpriv->flags at probe time. This
is to avoid breaking users that have not been tested with this change.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Suggested-by: Grzegorz Jaszczyk <jaz@semihalf.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 11 Jan 2019 20:28:01 +0000 (12:28 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has one core and one driver bugfix for you"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: tegra: Fix Maximum transfer size
i2c: dev: prevent adapter retries and timeout being set as minus value
Linus Torvalds [Fri, 11 Jan 2019 20:25:40 +0000 (12:25 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. Most of the complication comes
from improving our kpti code to avoid lengthy pauses (30+ seconds)
during boot when we rewrite the page tables. There are also a couple
of IORT fixes that came in via Lorenzo.
Summary:
- Don't error in kexec_file_load if kaslr-seed is missing in
device-tree
- Fix incorrect argument type passed to iort_match_node_callback()
- Fix IORT build failure when CONFIG_IOMMU_API=n
- Fix kpti performance regression with new rodata default option
- Typo fix"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: return successfully even if kaslr-seed doesn't exist
ACPI/IORT: Fix rc_dma_get_range()
arm64: kpti: Avoid rewriting early page tables when KASLR is enabled
arm64: asm-prototypes: Fix fat-fingered typo in comment
ACPI/IORT: Fix build when CONFIG_IOMMU_API=n
Linus Torvalds [Fri, 11 Jan 2019 20:17:30 +0000 (12:17 -0800)]
Merge tag 'ceph-for-5.0-rc2' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A patch to allow setting abort_on_full and a fix for an old "rbd
unmap" edge case, marked for stable"
* tag 'ceph-for-5.0-rc2' of git://github.com/ceph/ceph-client:
rbd: don't return 0 on unmap if RBD_DEV_FLAG_REMOVING is set
ceph: use vmf_error() in ceph_filemap_fault()
libceph: allow setting abort_on_full for rbd
Linus Torvalds [Fri, 11 Jan 2019 17:44:05 +0000 (09:44 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates from Ingo Molnar:
"Tooling changes only: fixes and a few stray improvements.
Most of the diffstat is dominated by a PowerPC related fix of system
call trace output beautification that allows us to (again) use the
UAPI header version and sync up with the kernel's version of PowerPC
system call names in the arch/powerpc/kernel/syscalls/syscall.tbl
header"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
tools headers powerpc: Remove unistd.h
perf powerpc: Rework syscall table generation
perf symbols: Add 'arch_cpu_idle' to the list of kernel idle symbols
tools include uapi: Sync linux/if_link.h copy with the kernel sources
tools include uapi: Sync linux/vhost.h with the kernel sources
tools include uapi: Sync linux/fs.h copy with the kernel sources
perf beauty: Switch from using uapi/linux/fs.h to uapi/linux/mount.h
tools include uapi: Grab a copy of linux/mount.h
perf top: Lift restriction on using callchains without "sym" in --sort
tools lib traceevent: Remove tep_data_event_from_type() API
tools lib traceevent: Rename tep_is_file_bigendian() to tep_file_bigendian()
tools lib traceevent: Changed return logic of tep_register_event_handler() API
tools lib traceevent: Changed return logic of trace_seq_printf() and trace_seq_vprintf() APIs
tools lib traceevent: Rename struct cmdline to struct tep_cmdline
tools lib traceevent: Initialize host_bigendian at tep_handle allocation
tools lib traceevent: Introduce new libtracevent API: tep_override_comm()
perf tests: Add a test for the ARM 32-bit [vectors] page
perf tools: Make find_vdso_map() more modular
perf trace: Fix alignment for [continued] lines
perf trace: Fix ')' placement in "interrupted" syscall lines
...
x86/kvm/nVMX: don't skip emulated instruction twice when vmptr address is not backed
Since commit 09abb5e3e5e50 ("KVM: nVMX: call kvm_skip_emulated_instruction
in nested_vmx_{fail,succeed}") nested_vmx_failValid() results in
kvm_skip_emulated_instruction() so doing it again in handle_vmptrld() when
vmptr address is not backed is wrong, we end up advancing RIP twice.
Fixes: fca91f6d60b6e ("kvm: nVMX: Set VM instruction error for VMPTRLD of unbacked page") Reported-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Lan Tianyu [Fri, 4 Jan 2019 07:20:44 +0000 (15:20 +0800)]
KVM/VMX: Avoid return error when flush tlb successfully in the hv_remote_flush_tlb_with_range()
The "ret" is initialized to be ENOTSUPP. The return value of
__hv_remote_flush_tlb_with_range() will be Or with "ret" when ept
table potiners are mismatched. This will cause return ENOTSUPP even if
flush tlb successfully. This patch is to fix the issue and set
"ret" to 0.
Fixes: a5c214dad198 ("KVM/VMX: Change hv flush logic when ept tables are mismatched.") Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Tomas Bortoli [Wed, 2 Jan 2019 17:29:37 +0000 (18:29 +0100)]
KVM: validate userspace input in kvm_clear_dirty_log_protect()
The function at issue does not fully validate the content of the
structure pointed by the log parameter, though its content has just been
copied from userspace and lacks validation. Fix that.
Moreover, change the type of n to unsigned long as that is the type
returned by kvm_dirty_bitmap_bytes().
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+028366e52c9ace67deb3@syzkaller.appspotmail.com
[Squashed the fix from Paolo. - Radim.] Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
ctl_bitmask in pt_desc is of type u64. When an integer like 0xf is
being left shifted more than 32 bits, the behavior is undefined.
Fix this by adding suffix ULL to integer 0xf.
Addresses-Coverity-ID: 1476095 ("Bad bit shift operation") Fixes: 6c0f0bba85a0 ("KVM: x86: Introduce a function to initialize the PT configuration") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Wei Yang <richardw.yang@linux.intel.com> Reviewed-by: Luwei Kang <luwei.kang@intel.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Linus Torvalds [Fri, 11 Jan 2019 17:07:19 +0000 (09:07 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A 32-bit build fix, CONFIG_RETPOLINE fixes and rename CONFIG_RESCTRL
to CONFIG_X86_RESCTRL"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, modpost: Replace last remnants of RETPOLINE with CONFIG_RETPOLINE
x86/cache: Rename config option to CONFIG_X86_RESCTRL
samples/seccomp: Fix 32-bit build
Linus Torvalds [Fri, 11 Jan 2019 17:04:36 +0000 (09:04 -0800)]
Merge tag 'acpi-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix a build failure introduced recently, fix the xpower PMIC ACPI
driver, clean up the handling of duplicate entries in _PRx power
resource lists and fix addresses in NUMA-related messages on 32-bit
with PAE.
Specifics:
- Fix build failures with both CONFIG_NLS and CONFIG_PCI unset that
can occur since ACPI can be built without PCI now (Sinan Kaya).
- Clean up the handling of duplicate entries in power resource lists
returned by _PRx evaluation to avoid triggering WARN_ON() on
attempts to add duplicate symlinks in sysfs (Hans de Goede).
- Fix issues with the TS current-source switching on systems using
the xpower PMIC by avoiding to update unrelated bits in the TS
pin-ctrl register and avoiding to unconditionally enable TS
current-source on systems where it is not used (Hans de Goede).
- Fix addresses in NUMA-related messages on 32-bit with PAE which can
be truncated due to integer type conversions (Chao Fan)"
* tag 'acpi-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: Fix TS-pin current-source handling
ACPI: NUMA: Use correct type for printing addresses on i386-PAE
ACPI: power: Skip duplicate power resource references in _PRx
ACPI: Fix build failure when CONFIG_NLS is set to 'n'
Linus Torvalds [Fri, 11 Jan 2019 17:01:43 +0000 (09:01 -0800)]
Merge tag 'pm-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These fix fallout after starting to use hrtimers in the runtime PM
framework, fix a few cpufreq issues, fix a recently broken reference
to cpuidle documentation, update MAINTAINERS entries for cpufreq and
cpuidle and make the recently added system suspend and resume support
in devfreq actually work.
Specifics:
- Prevent integer overflows from occurring on 32-bit when converting
milliseconds to nanoseconds in the runtime PM framework and update
comments that still refer to jiffies in it (Vincent Guittot,
Ladislav Michl).
- Fix the SCMI cpufreq driver to always use the same frequency units
for arch_set_freq_scale() and make the scale-invariant load
tracking acutally work with this driver (Quentin Perret).
- Fix freeing of dynamic OPPs in the SCPI and SCMI cpufreq drivers
broken during the 4.20 defelopment cycle (Viresh Kumar).
- Prevent the cpufreq core from attempting to return the current
frequency of offline CPUs (Sudeep Holla).
- Add devfreq suspend and resume hooks (missed previously) to the PM
core to make the recently added system suspend and resume support
in devfreq actually work (Lukasz Luba).
- Update MAINTAINERS entries for cpufreq and cpuidle, mostly to add
references to new/current documentation to them (Rafael Wysocki).
- Fix a recently broken reference to cpuidle documentation (Otto
Sabart)"
* tag 'pm-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix autosuspend_delay on 32bits arch
PM-runtime: Fix 'jiffies' in comments after switch to hrtimers
cpufreq: scmi: Fix frequency invariance in slow path
doc: trace: fix reference to cpuidle documentation file
cpufreq: check if policy is inactive early in __cpufreq_get()
cpufreq: scpi/scmi: Fix freeing of dynamic OPPs
cpuidle / Documentation: Update cpuidle MAINTAINERS entry
cpufreq / Documentation: Update cpufreq MAINTAINERS entry
PM: sleep: call devfreq suspend/resume
Linus Torvalds [Fri, 11 Jan 2019 16:58:02 +0000 (08:58 -0800)]
Merge tag 'drm-fixes-2019-01-11' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Not a huge amount for rc2, assume the usual quiet period, and rc3 will
be most of it.
amdgpu:
- Powerplay fixes
- Virtual display pinning fixes
- Golden register updates for Vega
- Pitch and gem size validation fixes
- SR-IOV init error fix
- Pagetables in system RAM disable for some Raven system
- DP-MST resume fixes
tc358767 bridge:
- fix to work with displayport connector"
* tag 'drm-fixes-2019-01-11' of git://anongit.freedesktop.org/drm/drm: (26 commits)
drm/amdgpu: disable system memory page tables for now
drm/amdgpu: set WRITE_BURST_LENGTH to 64B to workaround SDMA1 hang
drm/amdgpu: fix CPDMA hang in PRT mode for VEGA20
drm/bridge: tc358767: use DP connector if no panel set
drm/bridge: tc358767: fix output H/V syncs
drm/bridge: tc358767: reject modes which require too much BW
drm/bridge: tc358767: fix initial DP0/1_SRCCTRL value
drm/bridge: tc358767: fix single lane configuration
drm/bridge: tc358767: add defines for DP1_SRCCTRL & PHY_2LANE
drm/bridge: tc358767: add bus flags
drm/dp_mst: Add __must_check to drm_dp_mst_topology_mgr_resume()
drm/amdgpu: Don't fail resume process if resuming atomic state fails
drm/amdgpu: Don't ignore rc from drm_dp_mst_topology_mgr_resume()
drm/amdgpu: validate user GEM object size
drm/amdgpu: validate user pitch alignment
drm/amd/powerplay: drop the unnecessary uclk hard min setting
drm/amd/powerplay: avoid possible buffer overflow
drm/amd/powerplay: create pp_od_clk_voltage device file under OD support
drm/amd/powerplay: update OD support flag for SKU with no OD capabilities
drm/amdgpu: make gfx9 enter into rlc safe mode when set MGCG
...
projects / mirror_ubuntu-kernels.git / log