Dingchen Zhang [Wed, 15 May 2019 21:15:05 +0000 (17:15 -0400)]
drm/amd/display: add functionality to grab DPRX CRC entries.
[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.
[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Julian Parkin [Thu, 13 Jun 2019 16:49:37 +0000 (12:49 -0400)]
drm/amd/display: Poll for GPUVM context ready (v2)
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Wed, 12 Jun 2019 20:30:15 +0000 (16:30 -0400)]
drm/amd/display: add monitor patch to add T7 delay
[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.
It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.
Customer is asking to add fixed T7 delay as panel
workaround.
[How]
Add monitor specific patch to add T7 delay
Signed-off-by: Anthony Koo <anthony.koo@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds EMP packet programming for enabling dsc with
hdmi. The packets are structured according to VESA HDMI 2.1x
r2 spec, section 10.10.2.2.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Su Sung Chung [Wed, 22 May 2019 18:28:52 +0000 (14:28 -0400)]
drm/amd/display: refactor dump_clk_registers
[why]
for 2 purposes:
1. get raw register value dumped on the log, which will make it easier
to talk to other team who only knows about the register
2. enable other HW to be able to use the same interface as raven to log
clock register data
Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Tue, 11 Jun 2019 22:18:36 +0000 (18:18 -0400)]
drm/amd/display: wait for the whole frame after global unlock
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nevenko Stupar [Tue, 11 Jun 2019 21:35:16 +0000 (17:35 -0400)]
drm/amd/display:Use Pixel clock in 100Hz units for HDMI Audio wall clock DTO
[Why]
-Pass and use pixel clock in 100 Hz to Audio for HDMI
audio DTO for Audio wall clock programming so audio DTO gets
increased precision for timings with /1001 factor.
-For HDMI TMDS for N and CTS ACR tables are based on 10 KHz
units, these does not need to be modified as N and CTS values
are still valid using current tables.
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Copy max_clks_by_state after dce_clk_mgr_construct
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: David Francis <David.Francis@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Murton Liu [Mon, 10 Jun 2019 21:55:28 +0000 (17:55 -0400)]
drm/amd/display: Clock does not lower in Updateplanes
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Galiffi [Sat, 8 Jun 2019 01:32:34 +0000 (21:32 -0400)]
drm/amd/display: Incorrect Read Interval Time For CR Sequence
[WHY]
TRAINING_AUX_RD_INTERVAL (DPCD 000Eh) modifies the read interval
for the EQ training sequence. CR read interval should remain 100 us.
Currently, the CR interval is also being modified.
[HOW]
lt_settings->cr_pattern_time should always be 100 us.
Signed-off-by: David Galiffi <david.galiffi@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Charlene Liu [Wed, 5 Jun 2019 19:21:03 +0000 (15:21 -0400)]
drm/amd/display: Split out common HUBP registers and code
There are shared regs and code across DCN generations. Pull them out
into a shared common location.
Also, expose some dcn20 init functions.
Signed-off-by: Charlene Liu <charlene.liu@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Samson Tam [Tue, 4 Jun 2019 19:52:59 +0000 (15:52 -0400)]
drm/amd/display: skip retrain in dc_link_set_preferred_link_settings() if using passive dongle
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Wed, 5 Jun 2019 14:53:40 +0000 (10:53 -0400)]
drm/amd/display: swap system aperture high/low
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nikola Cornij [Wed, 5 Jun 2019 18:29:47 +0000 (14:29 -0400)]
drm/amd/display: Set one 4:2:0-related PPS field as recommended by DSC spec
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Set default block_size, even in unexpected cases
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Tue, 4 Jun 2019 22:14:43 +0000 (18:14 -0400)]
drm/amd/display: early return when pipe_cnt is 0 in bw validation
[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.
[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <tong.cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Francis [Tue, 4 Jun 2019 20:05:14 +0000 (16:05 -0400)]
drm/amd/display: Update drm_dsc to reflect native 4.2.0 DSC spec
[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures
[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chiawen Huang [Tue, 14 May 2019 08:16:11 +0000 (16:16 +0800)]
drm/amd/display: Add aux tracing log in dce
[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce
[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com> Reviewed-by: Tony Cheng <tong.cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: No audio endpoint for Dell MST display
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com> Reviewed-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Mon, 3 Jun 2019 15:37:44 +0000 (11:37 -0400)]
drm/amd/display: cap DCFCLK hardmin to 507 for NV10
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Wed, 22 May 2019 18:24:40 +0000 (14:24 -0400)]
drm/amd/display: move bw calc code into helpers
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Mon, 3 Jun 2019 12:13:12 +0000 (08:13 -0400)]
drm/amd/display: fix up HUBBUB hw programming for VM
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Galiffi [Thu, 30 May 2019 15:56:39 +0000 (11:56 -0400)]
drm/amd/display: Add ability to set preferred link training parameters.
[WHY]
To add support for OS requirement to set preferred link training
parameters.
[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: David Galiffi <David.Galiffi@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Lei [Fri, 31 May 2019 19:14:13 +0000 (15:14 -0400)]
drm/amd/display: initialize p_state to proper value
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Liu [Thu, 18 Jul 2019 15:38:46 +0000 (11:38 -0400)]
drm/amdgpu: use VCN firmware offset for cache window
Since we are using the signed FW now, and also using PSP firmware loading,
but it's still potential to break driver when loading FW directly
instead of PSP, so we should add offset.
Signed-off-by: Leo Liu <leo.liu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/ttm: use the same attributes when freeing d_page->vaddr
In function __ttm_dma_alloc_page(), d_page->addr is allocated
by dma_alloc_attrs() but freed with use dma_free_coherent() in
__ttm_dma_free_page().
Use the correct dma_free_attrs() to free d_page->vaddr.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Thu, 18 Jul 2019 07:46:55 +0000 (15:46 +0800)]
drm/amd/powerplay: change sysfs pp_dpm_xxx format for navi10
v2:
set average clock value on level 1 when current clock equal
min or max clock (fine grained dpm support).
the navi10 gfxclk (sclk) support fine grained DPM,
so use level 1 to show current dpm freq in sysfs pp_dpm_xxx
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
this function is not needed any more. error injection is
the only way to validate ras but it can't be executed in
amdgpu_ras_init, where gpu is even not initialized
Evan Quan [Wed, 17 Jul 2019 08:32:27 +0000 (16:32 +0800)]
drm/amd/powerplay: report bootup clock as max supported on dpm disabled
With gfxclk or uclk dpm disabled, it's reasonable to report bootup clock
as the max supported.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GDS and GWS blocks default to allowing all VMIDs to
access all entries. Graphics VMIDs can handle setting
these limits when the driver launches work. However,
compute workloads under HWS control don't go through the
kernel driver. Instead, HWS firmware should set these
limits when a process is put into a VMID slot.
Disable access to these devices by default by turning off
all mask bits (for OA) and setting BASE=SIZE=0 (for GDS
and GWS) for all compute VMIDs. If a process wants to use
these resources, they can request this from the HWS
firmware (when such capabilities are enabled). HWS will
then handle setting the base and limit for the process when
it is assigned to a VMID.
This will also prevent user kernels from getting 'stuck' in
GWS by accident if they write GWS-using code but HWS
firmware is not set up to handle GWS reset. Until HWS is
enabled to handle GWS properly, all GWS accesses will
MEM_VIOL fault the kernel.
v2: Move initialization outside of SRBM mutex
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jonathan Kim [Thu, 11 Jul 2019 16:19:44 +0000 (12:19 -0400)]
drm/amdgpu: exposing fica registers to df offsets
exposing fica registers to poll df pie data for xgmi error counters for
vega20.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com> Reviewed-by: Alexander Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
James Zhu [Mon, 1 Jul 2019 23:12:14 +0000 (19:12 -0400)]
drm/amdgpu:add all VCN rings into schedule request queue
Add all VCN instances' decode/encode/jpeg decode rings into
drm_sched_rq list.
Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Boyuan Zhang <boyuan.zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Wed, 3 Jul 2019 03:01:59 +0000 (22:01 -0500)]
drm/amdkfd: Increase vcrat size for GPU
GPU cache info (part of virtual CRAT) size depends on CU number.
For arcturus, CU number has been increased. So the required memory
for vcrat also increases.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Yong Zhao <Yong.Zhao@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Le Ma [Tue, 2 Jul 2019 03:15:37 +0000 (11:15 +0800)]
drm/amdgpu: enable all 8 sdma instances for Arcturus silicon
The more 6 sdma instances work fine now with DF fix in vbios:
* mmDF_PIE_AON_MiscClientsEnable(0x1c728)=0x3fe(DF_ALL_INSTANCE)
[9:4]MmhubsEnable=3f (change from 0)
Signed-off-by: Le Ma <le.ma@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Le Ma [Fri, 28 Jun 2019 07:08:04 +0000 (15:08 +0800)]
drm/amdgpu: clean up nonexistent firmware declaration for Arcturus
CPG firmwares are not used.
Signed-off-by: Le Ma <le.ma@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Wed, 20 Mar 2019 21:04:10 +0000 (16:04 -0500)]
drm/amdgpu: Enable xgmi support for Arcturus
xgmi is a high performance cross-GPU communication channel.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Thu, 14 Mar 2019 16:44:24 +0000 (11:44 -0500)]
drm/amdgpu: Hack xgmi topology info when there is no psp fw
This is only needed on emulation platform where psp fw might
not be available, to hack xgmi topology info such as hive id and
node id.
v2: Add offset to hacked hive/node id
v3: Don't use introduce new module parameter.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Tue, 9 Jul 2019 14:59:30 +0000 (09:59 -0500)]
drm/amdkfd: Implement kfd2kgd_calls for Arcturus
Arcturus shares most of the kfd2kgd_calls with gfx9. But due to
SDMA register address change, it can't share SDMA related functions.
Export gfx9 kfd2kgd_calls and implement SDMA related functions
for Arcturus.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Tue, 19 Feb 2019 20:59:51 +0000 (14:59 -0600)]
drm/amdkfd: Support bigger gds size
Extend map_process and set_resources pm4 packet to support
bigger gds size for arcturus.
v2: Only make the change for v9
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / mirror_ubuntu-kernels.git / log