Johannes Berg [Wed, 7 Dec 2011 08:02:21 +0000 (09:02 +0100)]
mac80211: fix another race in aggregation start
Emmanuel noticed that when mac80211 stops the queues
for aggregation that can leave a packet pending. This
packet will be given to the driver after the AMPDU
callback, but as a non-aggregated packet which messes
up the sequence number etc.
I also noticed by looking at the code that if packets
are being processed while we clear the WANT_START bit,
they might see it cleared already and queue up on
tid_tx->pending. If the driver then rejects the new
aggregation session we leak the packet.
Fix both of these issues by changing this code to not
stop the queues at all. Instead, let packets queue up
on the tid_tx->pending queue instead of letting them
get to the driver, and add code to recover properly
in case the driver rejects the session.
(The patch looks large because it has to move two
functions to before their new use.)
Cc: stable@vger.kernel.org Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:19:19 +0000 (08:19 -0800)]
iwlwifi: change the default behavior of watchdog timer
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+ Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:19:17 +0000 (08:19 -0800)]
iwlagn: fix HW crypto for TX-only keys
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 30 Nov 2011 15:56:30 +0000 (16:56 +0100)]
mac80211: fill rate filter for internal scan requests
The rates bitmap for internal scan requests shoud be filled,
otherwise there will be probe requests with zero rates supported.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: fix race on init and driver registration
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
Cc: stable@vger.kernel.org Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: fix race between the AGG SM and the Tx data path
When a packet is supposed to sent be as an a-MPDU, mac80211 sets
IEEE80211_TX_CTL_AMPDU to let the driver know. On the other
hand, mac80211 configures the driver for aggregration with the
ampdu_action callback.
There is race between these two mechanisms since the following
scenario can occur when the BA agreement is torn down:
check OPERATIONAL bit
Set the TX_CTL_AMPDU bit in the packet
clear OPERATIONAL bit
stop Tx AGG
Pass Tx packet to the driver.
In that case the driver would get a packet with TX_CTL_AMPDU set
although it has already been notified that the BA session has been
torn down.
To fix this, we need to synchronize all the Qdisc activity after we
cleared the OPERATIONAL bit. After that step, all the following
packets will be buffered until the driver reports it is ready to get
new packets for this RA / TID. This buffering allows not to run into
another race that would send packets with TX_CTL_AMPDU unset while
the driver hasn't been requested to tear down the BA session yet.
This race occurs in practice and iwlwifi complains with a WARN_ON
when it happens.
Cc: stable@kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nikolay Martynov [Mon, 28 Nov 2011 08:18:00 +0000 (09:18 +0100)]
mac80211: fix race condition caused by late addBA response
If addBA responses comes in just after addba_resp_timer has
expired mac80211 will still accept it and try to open the
aggregation session. This causes drivers to be confused and
in some cases even crash.
This patch fixes the race condition and makes sure that if
addba_resp_timer has expired addBA response is not longer
accepted and we do not try to open half-closed session.
Cc: stable@vger.kernel.org Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
[some adjustments] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Revert change that broke AR928X on Acer Ferrari One
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2320f1d2f09be122efef5b9118efee4 (ath9k_hw: Add
support for AR946/8x chipsets) that caused a nasty regression to
appear on my Acer Ferrari One (the box locks up entirely at random
times after the wireless has been started without any way to get
debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 24 Nov 2011 19:06:14 +0000 (20:06 +0100)]
mac80211: don't stop a single aggregation session twice
Nikolay noticed (by code review) that mac80211 can
attempt to stop an aggregation session while it is
already being stopped. So to fix it, check whether
stop is already being done and bail out if so.
Also move setting the STOPPING state into the lock
so things are properly atomic.
Cc: stable@vger.kernel.org Reported-by: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 21 Nov 2011 09:44:00 +0000 (10:44 +0100)]
cfg80211: fix regulatory NULL dereference
By the time userspace returns with a response to
the regulatory domain request, the wiphy causing
the request might have gone away. If this is so,
reject the update but mark the request as having
been processed anyway.
Cc: Luis R. Rodriguez <lrodriguez@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Thu, 17 Nov 2011 22:53:36 +0000 (14:53 -0800)]
mac80211: Fix AMSDU rate printout in debugfs.
It was flipped. See section 7.3.2.56 of the 802.11n
spec for details.
Signed-off-by: Ben Greear <greearb@candelatech.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Büsch [Wed, 16 Nov 2011 22:55:46 +0000 (23:55 +0100)]
p54spi: Fix workqueue deadlock
priv->work must not be synced while priv->mutex is locked, because
the mutex is taken in the work handler.
Move cancel_work_sync down to after the device shutdown code.
This is safe, because the work handler checks fw_state and bails out
early in case of a race.
Signed-off-by: Michael Buesch <m@bues.ch> Cc: <stable@vger.kernel.org> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Büsch [Wed, 16 Nov 2011 22:48:31 +0000 (23:48 +0100)]
p54spi: Add missing spin_lock_init
The tx_lock is not initialized properly. Add spin_lock_init().
Signed-off-by: Michael Buesch <m@bues.ch> Cc: <stable@vger.kernel.org> Acked-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix __le32 to __le16 conversion of the first word of an 8-word block
of EEPROM read via the efuse method.
Reported-and-tested-by: Ingvar Hagelund <ingvar@redpill-linpro.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> CC: <stable@vger.kernel.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have documented case of very bad performance issue on rt2800pci
device, because it generate spurious interrupt, what cause irq line
is disabled: https://bugzilla.redhat.com/show_bug.cgi?id=658451
We already address that problem in separate patch by returning
IRQ_HANDLED from interrupt handler. We think similar fix is needed for
other rt2x00 PCI devices, because users report performance problems on
these devices too.
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices may generate spurious interrupts, we have to handle them
otherwise interrupt line will be disabled with below message and driver
will not work:
Reported-and-tested-by: Amir Hedayaty <hedayaty@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jesper Juhl [Sun, 13 Nov 2011 21:14:32 +0000 (22:14 +0100)]
Net, libertas: Resolve memory leak in if_spi_host_to_card()
If we hit the default case in the switch in if_spi_host_to_card() we'll leak
the memory we allocated for 'packet'. This patch resolves the leak by freeing
the allocated memory in that case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Fix sleep-while-atomic bug in powersaving code.
The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.
Fix this by moving the call to rt2x00lib_config to a workqueue call.
This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672
Tested-by: Tomas Trnka <tomastrnka@gmx.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Cc: <stable@vger.kernel.org> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Teika Kazura <teika@lavabit.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Thu, 10 Nov 2011 05:36:21 +0000 (21:36 -0800)]
mwifiex: fix association issue with AP configured in hidden SSID mode
Firmware expects 'max_ssid_length' field in
'struct mwifiex_ie_types_wildcard_ssid_params' to be '0' for
performing SSID specific scan. Currently driver updates it with
an actual SSID length. Hence UUT is not able to find the AP
configured in hidden SSID mode in scan results and association
fails.
max_ssid_length is filled with '0' to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: avoid a panic when unloading the module with RF Kill
When HW RF kill switch is set to kill the radio, our NIC issues an
interrupt after we stop the APM module. When we unload the module,
the driver disables and cleans the interrupts before stopping the
APM. So we have a real interrupt (inta not zero) pending.
When this interrupts pops up the tasklet has already been killed
and we crash.
Here is a logical description of the flow:
disable and clean interrupts
synchronize interrupts
kill the tasklet
stop the APM <<== creates an RF kill interrupt
free_irq <<== somehow our ISR is called here and we crash
Johannes Berg [Wed, 9 Nov 2011 11:14:16 +0000 (12:14 +0100)]
mac80211: fix race between connection monitor & suspend
When the connection monitor timer fires right before
suspend, the following will happen:
timer fires -> monitor_work gets queued
suspend calls ieee80211_sta_quiesce
ieee80211_sta_quiesce:
- deletes timer
- cancels monitor_work synchronously, running it
[note wrong order of these steps]
monitor_work runs, re-arming the timer
later, timer fires while system should be quiesced
This causes a warning:
WARNING: at net/mac80211/util.c:540 ieee80211_can_queue_work+0x35/0x40 [mac80211]()
but is otherwise harmless. I'm not completely sure
this is the scenario Thomas stumbled across, but it
is the only way I can right now see the warning in
a scenario like the one he reported.
Reported-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: fix bug on regulatory core exit on access to last_request
Commit 4d9d88d1 by Scott James Remnant <keybuk@google.com> added
the .uevent() callback for the regulatory device used during
the platform device registration. The change was done to account
for queuing up udev change requests through udevadm triggers.
The change also meant that upon regulatory core exit we will now
send a uevent() but the uevent() callback, reg_device_uevent(),
also accessed last_request. Right before commiting device suicide
we free'd last_request but never set it to NULL so
platform_device_unregister() would lead to bogus kernel paging
request. Fix this and also simply supress uevents right before
we commit suicide as they are pointless.
The impact of not having this present is that a bogus paging
access may occur (only read) upon cfg80211 unload time. You
may also get this BUG complaint below. Although Johannes
could not reproduce the issue this fix is theoretically correct.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Cc: Scott James Remnant <keybuk@google.com> Cc: stable@vger.kernel.org Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 8 Nov 2011 11:28:33 +0000 (12:28 +0100)]
mac80211: fix NULL dereference in radiotap code
When receiving failed PLCP frames is enabled, there
won't be a rate pointer when we add the radiotap
header and thus the kernel will crash. Fix this by
not assuming the rate pointer is always valid. It's
still always valid for frames that have good PLCP
though, and that is checked & enforced.
where I removed the check in this case but didn't
take into account that the rate info would be used.
Reported-by: Xiaokang Qin <xiaokang.qin@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 8 Nov 2011 13:01:13 +0000 (14:01 +0100)]
ath: Fix NULL ptr dereference in ath_reg_apply_world_flags
This happens with devices using a regulatory domain 0x68 that are only
5Ghz capable because ath_reg_apply_active_scan_flags assumes that we
always have a 2,4Ghz band.
Bluetooth: Use miliseconds for L2CAP channel timeouts
Timers set by __set_chan_timer() should use miliseconds instead of
jiffies. Commit 942ecc9c4643db5ce071562e0a23f99464d6b461 updated
l2cap_set_timer() so it expects timeout to be specified in msecs
instead of jiffies. This makes timeouts unreliable when CONFIG_HZ
is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This reverts commit 330605423ca6eafafb8dcc27502bce1c585d1b06.
The commit introduces regression when two 2.1 devices attempt
establish rfcomm channel. Such connection is refused since there's
a security block issue on l2cap. It means the link is unencrypted.
mac80211: uAPSD - fix IEEE80211_FCTL_MOREDATA bit setting
Set IEEE80211_FCTL_MOREDATA bit also in case we have buffered
frames (more than one) only for one AC.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jesper Juhl [Sun, 6 Nov 2011 21:58:31 +0000 (22:58 +0100)]
net, wireless, mwifiex: Fix mem leak in mwifiex_update_curr_bss_params()
If kmemdup() fails we leak the memory allocated to bss_desc.
This patch fixes the leak.
I also removed the pointless default assignment of 'NULL' to 'bss_desc'
while I was there anyway.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 4 Nov 2011 10:01:46 +0000 (11:01 +0100)]
cfg80211: fix cmp_ies
When comparing two items by IE, the sort order
wasn't stable, which could lead to issues in the
rbtree. Make it stable by making a missing IE
sort before a present IE.
Also sort by length first if it differs and then
by contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 3 Nov 2011 13:50:13 +0000 (14:50 +0100)]
cfg80211: allow setting TXQ parameters only in AP mode
In other modes the parameters should not be set.
Right now, mac80211 will set them, even if the
user asked for setting them on VLANs which the
driver doesn't know about, causing all kinds of
trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 3 Nov 2011 08:27:01 +0000 (09:27 +0100)]
nl80211: fix HT capability attribute validation
Since the NL80211_ATTR_HT_CAPABILITY attribute is
used as a struct, it needs a minimum, not maximum
length. Enforce that properly. Not doing so could
potentially lead to reading after the buffer.
Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Sat, 29 Oct 2011 09:30:15 +0000 (11:30 +0200)]
brcm80211: smac: eliminate a null pointer dereference in dma.c
Though it's unlikely, di may be null, so we can't dereference
di->dma.dmactrlflags until we've checked it.
Move this de-reference after the check, and adjust the error
message to not require de-referencing di.
This is based upon Julia's original patch:
<1319846297-2985-2-git-send-email-julia@diku.dk>
Reported-by: Julia Lawall <julia@diku.dk> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Mon, 17 Oct 2011 14:59:25 +0000 (16:59 +0200)]
b43: fill ctl1 word on all newer PHYs, fix PHY errors
This fixes PHY transmission errors reported on some LP-PHY and HT-PHY
cards. For LP-PHY they were quite rare and not really noticable. On
HT-PHY they were critical, OFDM rates were not available at all.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 4 Nov 2011 17:07:43 +0000 (18:07 +0100)]
mac80211: warn only once about not finding a rate
The warning really shouldn't happen, but until we
find the reason why it does don't spew it all the
time, just once is enough to know we've hit it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Sun, 30 Oct 2011 06:15:15 +0000 (23:15 -0700)]
iwlwifi: don't perform "echo test" when cmd queue stuck
Perform "echo test" when cmd queue stuck detected, somethime it will cause
calltrace. I am not sure how to fix it yet, just remove the action now until
find a better way to handle it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 28 Oct 2011 17:17:49 +0000 (12:17 -0500)]
b43: Remove unneeded message
The driver can spam the logs with "RX: Packet dropped" messages. These drops
originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet
size underruns. Condition #3 logs a separate message, thus no dropped message
is needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 28 Oct 2011 09:59:47 +0000 (11:59 +0200)]
mac80211: disable powersave for broken APs
Only AID values 1-2007 are valid, but some APs have been
found to send random bogus values, in the reported case an
AP that was sending the AID field value 0xffff, an AID of
0x3fff (16383).
There isn't much we can do but disable powersave since
there's no way it can work properly in this case.
Cc: stable@vger.kernel.org Reported-by: Bill C Riemers <briemers@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 28 Oct 2011 00:19:39 +0000 (17:19 -0700)]
iwlwifi: allow pci_enable_msi fail
Continue the init process even fail to enable msi
out_iounmap is no longer used, remove it
Reported-by: werner <w.landgraf@ru.ru> Tested-by: werner <w.landgraf@ru.ru> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andres Salomon [Wed, 26 Oct 2011 17:19:26 +0000 (10:19 -0700)]
libertas: ensure we clean up a scan request properly
Commit 2e30168b ("libertas: terminate scan when stopping interface")
adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's
an outstanding cfg80211_scan_request. However, it assumes that the
scan request was allocated via the cfg80211 stack. Libertas has
its own internal allocation method, kept track of with
priv->internal_scan. This doesn't set scan_req->wiphy, amongst other
things, which results in hitting a BUG() when we call cfg80211_scan_done
on the request.
This provides a function to take care of the low-level scan_req cleanup
details. We simply call that to deal with finishing up scan requests.
The bug we were hitting was:
[ 964.321495] kernel BUG at net/wireless/core.h:87!
[ 964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 964.341963] pgd = dcf80000
...
[ 964.849998] 9fe0: 00000000beb417b84018e280401e822c60000010000000040000000000000000
[ 964.865007] [<c003104c>] (__bug+0x1c/0x28) from [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c)
[ 964.895324] [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c) from [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas])
[ 964.895324] [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas]) from [<c03002a0>] (__dev_close_many+0x94/0xc4)
[ 964.918995] [<c03002a0>] (__dev_close_many+0x94/0xc4) from [<c030037c>] (dev_close_many+0x78/0xe0)
Signed-off-by: Andres Salomon <dilinger@queued.net> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix noise floor calibration timeout on fast channel change
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Sun, 23 Oct 2011 19:36:04 +0000 (22:36 +0300)]
mac80211: Fix TDLS support validation in add_station handler
We need to verify whether the command is successful before allocating
the station entry to avoid extra processing. This also fixes a memory
leak on the error path.
Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix regression of register offset of AR9330/AR9340
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+] Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Thu, 20 Oct 2011 17:05:49 +0000 (19:05 +0200)]
mac80211: fix remain_off_channel regression
The offchannel code is currently broken - we should
remain_off_channel if the work was started, and
the work's channel and channel_type are the same
as local->tmp_channel and local->tmp_channel_type.
However, if wk->chan_type and local->tmp_channel_type
coexist (e.g. have the same channel type), we won't
remain_off_channel.
This behavior was introduced by commit da2fd1f
("mac80211: Allow work items to use existing
channel type.")
Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Eliad Peller <eliad@wizery.com> Cc: stable@kernel.org # 2.6.39+ Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix regression of register offset for AR9003 chips
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Herrmann [Wed, 26 Oct 2011 09:22:46 +0000 (11:22 +0200)]
Bluetooth: bfusb: Fix error path on firmware load
When loading the usb-configuration we do not signal the end of configuration on
memory allocation error. This patch moves the memory allocation to the top so
every error path uses "goto error" now to correctly send the usb-ctrl message
when detecting some error.
This also replaces GFP_ATOMIC with GFP_KERNEL as we are allowed to sleep here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 25 Oct 2011 19:13:36 +0000 (21:13 +0200)]
Bluetooth: bcm203x: Use GFP_KERNEL in workqueue
A workqueue is allowed to sleep so we can safely use GFP_KERNEL instead of
GFP_ATOMIC. This is still legacy code when the driver used timer BHs and not a
worqueue.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Wed, 26 Oct 2011 09:13:13 +0000 (11:13 +0200)]
Bluetooth: bcm203x: Fix race condition on disconnect
When disconnecting a bcm203x device we kill and destroy the usb-urb, however,
there might still be a pending work-structure which resubmits the now invalid
urb. To avoid this race condition, we simply set a shutdown-flag and
synchronously kill the worker first.
This also adds a comment to all schedule_work()s, as it is really not clear
that they are used as replacement for short timers (which can be seen in the git
history).
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 25 Oct 2011 10:09:52 +0000 (12:09 +0200)]
Bluetooth: ath3k: Use GFP_KERNEL instead of GFP_ATOMIC
We are allowed to sleep here so no need to use GFP_ATOMIC. The caller
(ath3k_probe) calls request_firmware() which definitely sleeps. Hence, we should
avoid using GFP_ATOMIC.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 24 Oct 2011 20:36:26 +0000 (22:36 +0200)]
Bluetooth: Set HCI_MGMT flag only in read_controller_info
The HCI_MGMT flag should only be set when user space requests the full
controller information. This way we avoid potential issues with setting
change events ariving before the actual read_controller_info command
finishes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Szymon Janc [Mon, 17 Oct 2011 21:05:49 +0000 (23:05 +0200)]
Bluetooth: Increase HCI reset timeout in hci_dev_do_close
I've noticed that my CSR usb dongle was not working if it was plugged in when
PC was booting. It looks like I get two HCI reset command complete events (see
hcidump logs below).
The root cause is reset called from off_timer. Timeout for this reset to
complete is set to 250ms and my bt dongle requires more time for replying with
command complete event. After that, chip seems to reply with reset command
complete event for next non-reset command.
Attached patch increase mentioned timeout to HCI_INIT_TIMEOUT, this value is
already used for timeouting hci_reset_req in hci_dev_reset().
This might also be related to BT not working after suspend that was reported
here some time ago.
Hcidump log:
2011-09-12 23:13:27.379465 < HCI Command: Reset (0x03|0x0003) plen 0
2011-09-12 23:13:27.380797 > HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
status 0x00
2011-09-12 23:13:27.380859 < HCI Command: Read Local Supported Features (0x04|0x000
3) plen 0
2011-09-12 23:13:27.760789 > HCI Event: Command Complete (0x0e) plen 4
Reset (0x03|0x0003) ncmd 1
status 0x00
2011-09-12 23:13:27.760831 < HCI Command: Read Local Version Information (0x04|0x00
01) plen 0
2011-09-12 23:13:27.764780 > HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 1.1 (0x1) HCI Revision: 0x36f
LMP Version: 1.1 (0x1) LMP Subversion: 0x36f
Manufacturer: Cambridge Silicon Radio (10)
Signed-off-by: Szymon Janc <szymon@janc.net.pl> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The route lookup to find a previously auto-configured route for a prefixes used
to use rt6_lookup(), with the prefix from the RA used as an address. However,
that kind of lookup ignores routing tables, the prefix length and route flags,
so when there were other matching routes, even in different tables and/or with
a different prefix length, the wrong route would be manipulated.
Now, a new function "addrconf_get_prefix_route()" is used for the route lookup,
which searches in RT6_TABLE_PREFIX and takes the prefix-length and route flags
into account.
Signed-off-by: Andreas Hofmeister <andi@collax.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh [Fri, 28 Oct 2011 15:42:50 +0000 (15:42 +0000)]
bonding: eliminate bond_close race conditions
This patch resolves two sets of race conditions.
Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the
first, as follows:
The bond_close() calls cancel_delayed_work() to cancel delayed works.
It, however, cannot cancel works that were already queued in workqueue.
The bond_open() initializes work->data, and proccess_one_work() refers
get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when
work->data has been initialized. Thus, a panic occurs.
He included a patch that converted the cancel_delayed_work calls
in bond_close to flush_delayed_work_sync, which eliminated the above
problem.
His patch is incorporated, at least in principle, into this
patch. In this patch, we use cancel_delayed_work_sync in place of
flush_delayed_work_sync, and also convert bond_uninit in addition to
bond_close.
This conversion to _sync, however, opens new races between
bond_close and three periodically executing workqueue functions:
bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon.
The race occurs because bond_close and bond_uninit are always
called with RTNL held, and these workqueue functions may acquire RTNL to
perform failover-related activities. If bond_close or bond_uninit is
waiting in cancel_delayed_work_sync, deadlock occurs.
These deadlocks are resolved by having the workqueue functions
acquire RTNL conditionally. If the rtnl_trylock() fails, the functions
reschedule and return immediately. For the cases that are attempting to
perform link failover, a delay of 1 is used; for the other cases, the
normal interval is used (as those activities are not as time critical).
Additionally, the bond_mii_monitor function now stores the delay
in a variable (mimicing the structure of activebackup_arp_mon).
Lastly, all of the above renders the kill_timers sentinel moot,
and therefore it has been removed.
Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
Instead, just checking for RESETTING_BIT not set before sending config_led
command down to card.
o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
config_led command down to make sure interface cannot be brought up/ down.
o Allocate and free resources if interface is down before
sending the config_led command. This is to make sure config_led
command sending doesn't fail.
o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sritej Velaga [Fri, 28 Oct 2011 12:57:14 +0000 (12:57 +0000)]
qlcnic: Updated License file
Updated qlcnic's license file.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Fri, 28 Oct 2011 12:57:13 +0000 (12:57 +0000)]
qlcnic: updated reset sequence
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: reset loopback mode if promiscous mode setting fails.
If promiscous mode setting fails, reset loopback mode setting in firmware.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sritej Velaga [Fri, 28 Oct 2011 12:57:11 +0000 (12:57 +0000)]
qlcnic: skip IDC ack check in fw reset path.
In fw reset path, we should consider any change in device state as an
ack from the other driver. When that happens, we don't have to wait for
an explicit ack.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao feng [Fri, 28 Oct 2011 02:46:57 +0000 (02:46 +0000)]
ipv6: fix route error binding peer in func icmp6_dst_alloc
in func icmp6_dst_alloc,dst_metric_set call ipv6_cow_metrics to set metric.
ipv6_cow_metrics may will call rt6_bind_peer to set rt6_info->rt6i_peer.
So,we should move ipv6_addr_copy before dst_metric_set to make sure rt6_bind_peer success.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the normal descriptor structure
to work fine on new GMAC Synopsys chips.
Normal descriptors were designed on the old MAC10/100
databook 1.91 where some bits were reserved: for example
the tx checksum insertion and rx checksum offload.
The patch maintains the back-compatibility with old
MAC devices (tested on STx7109 MAC10/100) and adds new
fields that actually new GMAC devices can use.
For example, STx7109 (MAC10/100) will pass from the platform
tx_coe = 0, enh_desc = 0, has_gmac = 0.
A platform like Loongson1B (GMAC) will pass:
tx_coe = 1, enh_desc = 0, has_gmac = 1.
Thanks to Kelvin, he enhanced the normal descriptors for
GMAC (on MIPS Loongson1B platform).
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Angus Clark [Wed, 26 Oct 2011 19:43:08 +0000 (19:43 +0000)]
stmmac: fix NULL pointer dereference in capabilities fixup (v2)
Signed-off-by: Angus Clark <angus.clark@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Thu, 27 Oct 2011 07:14:05 +0000 (07:14 +0000)]
be2net: Changing MAC Address of a VF was broken.
Allow for MAC Address change of VF(SR-IOV case) on the fly- First add and then
delete MAC Address to allow for 'out of pool' errors.
When MAC Addr configured from a VM, the MAC on the NIC will aleady have
the supplied MAC,so just copy the supplied MAC to the netdev structure
before returning success to the stack
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Thu, 27 Oct 2011 05:13:54 +0000 (05:13 +0000)]
bnx2x: update driver version to 1.70.30-0
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Thu, 27 Oct 2011 05:13:53 +0000 (05:13 +0000)]
bnx2x: use FW 7.0.29.0
The FW includes the following fixes:
1. (iSCSI) Arrival of un-solicited ASYNC message causes
firmware to abort the connection with RST.
2. (FCoE) There is a probability that truncated FCoE packet on
RX path won't get detected which might lead to FW assert.
3. (iSCSI) Arrival of target-initiated NOP-IN during intense
ISCSI traffic might lead to FW assert.
4. (iSCSI) Chip hangs when in case of retransmission not aligned
to 4-bytes from the beginning of iSCSI PDU.
5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-bionic-kernel.git / log