Linus Torvalds [Sun, 12 Nov 2017 18:12:41 +0000 (10:12 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of small fixes:
- make KGDB work again which got broken by the conversion of WARN()
to #UD. The WARN fixup needs to run before the notifier callchain,
otherwise KGDB tries to handle it and crashes.
- disable KASAN in the ORC unwinder to prevent false positive KASAN
warnings
- prevent default mapping above 47bit when 5 level page tables are
enabled
- make the delay calibration optimization work correctly, which had
the conditionals the wrong way around and was operating on data
which was not yet updated.
- remove the bogus X86_TRAP_BP trap init from the default IDT init
table, which broke 32bit int3 handling by overwriting the correct
int3 setup.
- replace this_cpu* with boot_cpu_data access in the preemptible
oprofile init code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/debug: Handle warnings before the notifier chain, to fix KGDB crash
x86/mm: Fix ELF_ET_DYN_BASE for 5-level paging
x86/idt: Remove X86_TRAP_BP initialization in idt_setup_traps()
x86/oprofile/ppro: Do not use __this_cpu*() in preemptible context
x86/unwind: Disable KASAN checking in the ORC unwinder
x86/smpboot: Make optimization of delay calibration work correctly
2) Handle NAPI poll with a zero budget properly in mlx5 driver, from
Saeed Mahameed.
3) If DMA mapping fails in mlx5 driver, NULL out page, from Inbar
Karmy.
4) Handle overrun in RX FIFO of sun4i CAN driver, from Gerhard
Bertelsmann.
5) Missing return in mdb and vlan prepare phase of DSA layer, from
Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a use-after-free in vlan_device_event()
net: dsa: return after vlan prepare phase
net: dsa: return after mdb prepare phase
can: ifi: Fix transmitter delay calculation
tcp: fix tcp_fastretrans_alert warning
tcp: gso: avoid refcount_t warning from tcp_gso_segment()
can: peak: Add support for new PCIe/M2 CAN FD interfaces
can: sun4i: handle overrun in RX FIFO
can: c_can: don't indicate triple sampling support for D_CAN
net/mlx5e: Increase Striding RQ minimum size limit to 4 multi-packet WQEs
net/mlx5e: Set page to null in case dma mapping fails
net/mlx5e: Fix napi poll with zero budget
net/mlx5: Cancel health poll before sending panic teardown command
net/mlx5: Loop over temp list to release delay events
rds: ib: Fix NULL pointer dereference in debug code
David S. Miller [Sat, 11 Nov 2017 12:52:01 +0000 (21:52 +0900)]
Merge tag 'linux-can-fixes-for-4.14-20171110' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-11-10
this is a pull request for net/master.
The first patch by Richard Schütz for the c_can driver removes the false
indication to support triple sampling for d_can. Gerhard Bertelsmann's
patch for the sun4i driver improves the RX overrun handling. The patch
by Stephane Grosjean for the peak_canfd driver adds the PCI ids for
various new PCIe/M2 interfaces. Marek Vasut's patch for the ifi driver
fix transmitter delay calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following series includes some fixes for mlx5 core and etherent
driver.
Sorry for the late submission but as you can see i have some very
critical fixes below that i would like them merged into this RC.
Please pull and let me know if there is any problem.
For -stable:
('net/mlx5e: Set page to null in case dma mapping fails') kernels >= 4.13
('net/mlx5: FPGA, return -EINVAL if size is zero') kernels >= 4.13
('net/mlx5: Cancel health poll before sending panic teardown command') kernels >= 4.13
V1->V2:
- Fix Reviewed-by tag of the 2nd patch.
- Drop the FPGA 0 size fix, it needs some more change log info.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 8 Nov 2017 15:50:10 +0000 (10:50 -0500)]
net: dsa: return after vlan prepare phase
The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.
Fixes: 1ca4aa9cd4cc ("net: dsa: check VLAN capability of every switch") Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 8 Nov 2017 15:49:56 +0000 (10:49 -0500)]
net: dsa: return after mdb prepare phase
The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.
Fixes: a1a6b7ea7f2d ("net: dsa: add cross-chip multicast support") Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 10 Nov 2017 22:14:23 +0000 (14:14 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
- a new ACPI ID for Elan touchpad found in yet another Ideapad model
- Synaptics RMI4 will allow binding to controllers reporting SMB
version 3 (note that we are not adding any new ACPI IDs to the
Synaptics PS/2 drover so unless user explicitly enables intertouch
support there is no user-visible change)
- a fixup to TSC 2004/5 touchscreen driver to mark input devices as
"direct" to help userspace identify the type of device they are
dealing with
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
Input: tsc200x-core - set INPUT_PROP_DIRECT
Input: elan_i2c - add ELAN060C to the ACPI table
Linus Torvalds [Fri, 10 Nov 2017 20:21:15 +0000 (12:21 -0800)]
Merge tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A final few MIPS fixes for 4.14:
- fix BMIPS NULL pointer dereference (4.7)
- fix AR7 early GPIO init allocation failure (3.19)
- fix dead serial output on certain AR7 platforms (2.6.35)"
* tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: AR7: Ensure that serial ports are properly set up
MIPS: AR7: Defer registration of GPIO
MIPS: BMIPS: Fix missing cbr address
.mailmap: Add Maciej W. Rozycki's Imagination e-mail address
Following my recent transition from Imagination Technologies to the=20
reincarnated MIPS company add a .mailmap mapping for my work address,
so that `scripts/get_maintainer.pl' gets it right for past commits.
Signed-off-by: Maciej W. Rozycki <macro@mips.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sadly, it turns out that we really can't just do the cross-CPU IPI to
all CPU's to get their proper frequencies, because it's much too
expensive on systems with lots of cores.
So we'll have to revert this for now, and revisit it using a smarter
model (probably doing one system-wide IPI at open time, and doing all
the frequency calculations in parallel).
Reported-by: WANG Chao <chao.wang@ucloud.cn> Reported-by: Ingo Molnar <mingo@kernel.org> Cc: Rafael J Wysocki <rafael.j.wysocki@intel.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 10 Nov 2017 17:59:41 +0000 (09:59 -0800)]
Merge tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Last few patches to wrap up.
Two i915 fixes that are on their way to stable, one vmware black
screen bug, and one const patch that I was going to drop, but it was
clearly a pretty safe one liner"
* tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Deconstruct struct sgt_dma initialiser
drm/i915: Reject unknown syncobj flags
drm/vmwgfx: Fix Ubuntu 17.10 Wayland black screen issue
drm/vmwgfx: constify vmw_fence_ops
Marek Vasut [Fri, 10 Nov 2017 10:22:39 +0000 (11:22 +0100)]
can: ifi: Fix transmitter delay calculation
The CANFD transmitter delay calculation formula was updated in the
latest software drop from IFI and improves the behavior of the IFI
CANFD core during bitrate switching. Use the new formula to improve
stability of the CANFD operation.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Markus Marb <markus@marb.org> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yuchung Cheng [Tue, 7 Nov 2017 23:33:43 +0000 (15:33 -0800)]
tcp: fix tcp_fastretrans_alert warning
This patch fixes the cause of an WARNING indicatng TCP has pending
retransmission in Open state in tcp_fastretrans_alert().
The root cause is a bad interaction between path mtu probing,
if enabled, and the RACK loss detection. Upong receiving a SACK
above the sequence of the MTU probing packet, RACK could mark the
probe packet lost in tcp_fastretrans_alert(), prior to calling
tcp_simple_retransmit().
tcp_simple_retransmit() only enters Loss state if it newly marks
the probe packet lost. If the probe packet is already identified as
lost by RACK, the sender remains in Open state with some packets
marked lost and retransmitted. Then the next SACK would trigger
the warning. The likely scenario is that the probe packet was
lost due to its size or network congestion. The actual impact of
this warning is small by potentially entering fast recovery an
ACK later.
The simple fix is always entering recovery (Loss) state if some
packet is marked lost during path MTU probing.
Fixes: a0370b3f3f2c ("tcp: enable RACK loss detection to trigger recovery") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Reported-by: Roman Gushchin <guro@fb.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 14afee4b6092 ("net: convert sock.sk_wmem_alloc from atomic_t to refcount_t") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can: peak: Add support for new PCIe/M2 CAN FD interfaces
This adds support for the following PEAK-System CAN FD interfaces:
PCAN-cPCIe FD CAN FD Interface for cPCI Serial (2 or 4 channels)
PCAN-PCIe/104-Express CAN FD Interface for PCIe/104-Express (1, 2 or 4 ch.)
PCAN-miniPCIe FD CAN FD Interface for PCIe Mini (1, 2 or 4 channels)
PCAN-PCIe FD OEM CAN FD Interface for PCIe OEM version (1, 2 or 4 ch.)
PCAN-M.2 CAN FD Interface for M.2 (1 or 2 channels)
Like the PCAN-PCIe FD interface, all of these boards run the same IP Core
that is able to handle CAN FD (see also http://www.peak-system.com).
SUN4Is CAN IP has a 64 byte deep FIFO buffer. If the buffer is not
drained fast enough (overrun) it's getting mangled. Already received
frames are dropped - the data can't be restored.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Richard Schütz [Sun, 29 Oct 2017 12:03:22 +0000 (13:03 +0100)]
can: c_can: don't indicate triple sampling support for D_CAN
The D_CAN controller doesn't provide a triple sampling mode, so don't set
the CAN_CTRLMODE_3_SAMPLES flag in ctrlmode_supported. Currently enabling
triple sampling is a no-op.
Signed-off-by: Richard Schütz <rschuetz@uni-koblenz.de> Cc: linux-stable <stable@vger.kernel.org> # >= v3.6 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
x86/debug: Handle warnings before the notifier chain, to fix KGDB crash
Commit:
9a93848fe787 ("x86/debug: Implement __WARN() using UD0")
turned warnings into UD0, but the fixup code only runs after the
notify_die() chain. This is a problem, in particular, with kgdb,
which kicks in as if it was a BUG().
Fix this by running the fixup code before the notifier chain in
the invalid op handler path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Tested-by: Ilya Dryomov <idryomov@gmail.com> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Richard Weinberger <richard.weinberger@gmail.com> Cc: <stable@vger.kernel.org> # v4.12+ Link: http://lkml.kernel.org/r/20170724100428.19173-1-alexander.shishkin@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is to prevent the case of working with a single MPWQE
(1 WQE is always reserved as RQ is linked-list).
When the WQE is fully consumed, HW should still have available buffer
in order not to drop packets.
Inbar Karmy [Sun, 15 Oct 2017 14:30:59 +0000 (17:30 +0300)]
net/mlx5e: Set page to null in case dma mapping fails
Currently, when dma mapping fails, put_page is called,
but the page is not set to null. Later, in the page_reuse treatment in
mlx5e_free_rx_descs(), mlx5e_page_release() is called for the second time,
improperly doing dma_unmap (for a non-mapped address) and an extra put_page.
Prevent this by nullifying the page pointer when dma_map fails.
Saeed Mahameed [Tue, 31 Oct 2017 22:34:00 +0000 (15:34 -0700)]
net/mlx5e: Fix napi poll with zero budget
napi->poll can be called with budget 0, e.g. in netpoll scenarios
where the caller only wants to poll TX rings
(poll_one_napi@net/core/netpoll.c).
The below commit changed RX polling from "while" loop to "do {} while",
which caused to ignore the initial budget and handle at least one RX
packet.
This fixes the following warning:
[ 2852.049194] mlx5e_napi_poll+0x0/0x260 [mlx5_core] exceeded budget in poll
[ 2852.049195] ------------[ cut here ]------------
[ 2852.049195] WARNING: CPU: 0 PID: 25691 at net/core/netpoll.c:171 netpoll_poll_dev+0x18a/0x1a0
Fixes: 4b7dfc992514 ("net/mlx5e: Early-return on empty completion queues") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Reported-by: Martin KaFai Lau <kafai@fb.com> Tested-by: Martin KaFai Lau <kafai@fb.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net/mlx5: Cancel health poll before sending panic teardown command
After the panic teardown firmware command, health_care detects the error
in PCI bus and calls the mlx5_pci_err_detected. This health_care flow is
no longer needed because the panic teardown firmware command will bring
down the PCI bus communication with the HCA.
The solution is to cancel the health care timer and its pending
workqueue request before sending panic teardown firmware command.
Kernel trace:
mlx5_core 0033:01:00.0: Shutdown was called
mlx5_core 0033:01:00.0: health_care:154:(pid 9304): handling bad device here
mlx5_core 0033:01:00.0: mlx5_handle_bad_state:114:(pid 9304): NIC state 1
mlx5_core 0033:01:00.0: mlx5_pci_err_detected was called
mlx5_core 0033:01:00.0: mlx5_enter_error_state:96:(pid 9304): start
mlx5_3:mlx5_ib_event:3061:(pid 9304): warning: event on port 0
mlx5_core 0033:01:00.0: mlx5_enter_error_state:104:(pid 9304): end
Unable to handle kernel paging request for data at address 0x0000003f
Faulting instruction address: 0xc0080000434b8c80
Fixes: 8812c24d28f4 ('net/mlx5: Add fast unload support in shutdown flow') Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now consider an invocation of rds_ib_recv_refill() from the worker
thread, which is preemptible. Further, assume that the worker thread
is preempted between the ib_post_recv() and rdsdebug() statements.
Then, if the preemption is due to a receive CQE event, the
rds_ib_recv_cqe_handler() will be invoked. This function processes
receive completions, including freeing up data structures, such as the
recv->r_frag.
In this scenario, rds_ib_recv_cqe_handler() will process the receive
WR posted above. That implies, that the recv->r_frag has been freed
before the above rdsdebug() statement has been executed. When it is
later executed, we will have a NULL pointer dereference:
This bug was provoked by compiling rds out-of-tree with
EXTRA_CFLAGS="-DRDS_DEBUG -DDEBUG" and inserting an artificial delay
between the rdsdebug() and ib_ib_port_recv() statements:
/* XXX when can this fail? */
ret = ib_post_recv(ic->i_cm_id->qp, &recv->r_wr, &failed_wr);
+ if (can_wait)
+ usleep_range(1000, 5000);
rdsdebug("recv %p ibinc %p page %p addr %lu ret %d\n", recv,
recv->r_ibinc, sg_page(&recv->r_frag->f_sg),
(long) ib_sg_dma_address(
The fix is simply to move the rdsdebug() statement up before the
ib_post_recv() and remove the printing of ret, which is taken care of
anyway by the non-debug code.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Reviewed-by: Knut Omang <knut.omang@oracle.com> Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 9 Nov 2017 21:38:18 +0000 (13:38 -0800)]
sysctl: add register_sysctl() dummy helper
register_sysctl() has been around for five years with commit fea478d4101a ("sysctl: Add register_sysctl for normal sysctl users") but
now that arm64 started using it, I ran into a compile error:
arch/arm64/kernel/armv8_deprecated.c: In function 'register_insn_emulation_sysctl':
arch/arm64/kernel/armv8_deprecated.c:257:2: error: implicit declaration of function 'register_sysctl'
This adds a inline function like we already have for
register_sysctl_paths() and register_sysctl_table().
Link: http://lkml.kernel.org/r/20171106133700.558647-1-arnd@arndb.de Fixes: 38b9aeb32fa7 ("arm64: Port deprecated instruction emulation to new sysctl interface") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: "Luis R. Rodriguez" <mcgrof@kernel.org> Cc: Alex Benne <alex.bennee@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 10 Nov 2017 01:43:27 +0000 (17:43 -0800)]
Merge tag 'pci-v4.14-fixes-7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI maintainership updates from Bjorn Helgaas:
"Update MAINTAINERS for HiSilicon, Microsemi Switchtec, and native host
bridge drivers (Gabriele Paoloni, Sebastian Andrzej Siewior).
Note that starting with changes intended for v4.16, Lorenzo Pieralisi
will maintain the drivers/pci/{dwc,endpoint,host} directories. My
intent is to continue to merge those changes via my tree, so this
should be transparent to you"
* tag 'pci-v4.14-fixes-7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Lorenzo Pieralisi for PCI host bridge drivers
MAINTAINERS: Remove Gabriele Paoloni as HiSilicon PCI maintainer
MAINTAINERS: Remove Stephen Bates as Microsemi Switchtec maintainer
Linus Torvalds [Thu, 9 Nov 2017 19:16:28 +0000 (11:16 -0800)]
Merge tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull final power management fixes from Rafael Wysocki:
"These fix a regression in the schedutil cpufreq governor introduced by
a recent change and blacklist Dell XPS13 9360 from using the Low Power
S0 Idle _DSM interface which triggers serious problems on one of these
machines.
Specifics:
- Prevent the schedutil cpufreq governor from using the utilization
of a wrong CPU in some cases which started to happen after one of
the recent changes in it (Chris Redpath).
- Blacklist Dell XPS13 9360 from using the Low Power S0 Idle _DSM
interface as that causes serious issue (related to NVMe) to appear
on one of these machines, even though the other Dells XPS13 9360 in
somewhat different HW configurations behave correctly (Rafael
Wysocki)"
* tag 'pm-final-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell XPS13 9360
cpufreq: schedutil: Examine the correct CPU when we update util
Linus Torvalds [Thu, 9 Nov 2017 17:58:11 +0000 (09:58 -0800)]
Merge tag 'sound-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The amount of the changes isn't as quite small as wished, nevertheless
they are straight fixes that deserve merging to 4.14 final.
Most of fixes are about ALSA core bugs spotted by fuzzer: a follow-up
fix for the previous nested rwsem patch, a fix to avoid the resource
hogs due to too many concurrent ALSA timer invocations, and a fix for
a crash with SYSEX MIDI transfer over OSS sequencer emulation that is
used by none but fuzzer.
The rest are usual HD-audio and USB-audio device-specific quirks,
which are safe to apply"
* tag 'sound-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix headset mic problem for Dell machines with alc274
ALSA: seq: Fix OSS sysex delivery in OSS emulation
ALSA: seq: Avoid invalid lockdep class warning
ALSA: timer: Limit max instances per timer
ALSA: usb-audio: support new Amanero Combo384 firmware version
1) Fix use-after-free in IPSEC input parsing, desintation address
pointer was loaded before pskb_may_pull() which can change the SKB
data pointers. From Florian Westphal.
2) Stack out-of-bounds read in xfrm_state_find(), from Steffen
Klassert.
3) IPVS state of SKB is not properly reset when moving between
namespaces, from Ye Yin.
4) Fix crash in asix driver suspend and resume, from Andrey Konovalov.
5) Don't deliver ipv6 l2tp tunnel packets to ipv4 l2tp tunnels, and
vice versa, from Guillaume Nault.
6) Fix DSACK undo on non-dup ACKs, from Priyaranjan Jha.
7) Fix regression in bond_xmit_hash()'s behavior after the TCP port
selection changes back in 4.2, from Hangbin Liu.
8) Two divide by zero bugs in USB networking drivers when parsing
descriptors, from Bjorn Mork.
9) Fix bonding slaves being stuck in BOND_LINK_FAIL state, from Jay
Vosburgh.
10) Missing skb_reset_mac_header() in qmi_wwan, from Kristian Evensen.
11) Fix the destruction of tc action object races properly, from Cong
Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (31 commits)
cls_u32: use tcf_exts_get_net() before call_rcu()
cls_tcindex: use tcf_exts_get_net() before call_rcu()
cls_rsvp: use tcf_exts_get_net() before call_rcu()
cls_route: use tcf_exts_get_net() before call_rcu()
cls_matchall: use tcf_exts_get_net() before call_rcu()
cls_fw: use tcf_exts_get_net() before call_rcu()
cls_flower: use tcf_exts_get_net() before call_rcu()
cls_flow: use tcf_exts_get_net() before call_rcu()
cls_cgroup: use tcf_exts_get_net() before call_rcu()
cls_bpf: use tcf_exts_get_net() before call_rcu()
cls_basic: use tcf_exts_get_net() before call_rcu()
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Revert "net_sched: hold netns refcnt for each action"
net: usb: asix: fill null-ptr-deref in asix_suspend
Revert "net: usb: asix: fill null-ptr-deref in asix_suspend"
qmi_wwan: Add missing skb_reset_mac_header-call
bonding: fix slave stuck in BOND_LINK_FAIL state
qrtr: Move to postcore_initcall
net: qmi_wwan: fix divide by 0 on bad descriptors
net: cdc_ether: fix divide by 0 on bad descriptors
...
On machines with 5-level paging we don't want to allocate mapping above
47-bit unless user explicitly asked for it. See b569bab78d8d ("x86/mm:
Prepare to expose larger address space to userspace") for details.
c715b72c1ba4 ("mm: revert x86_64 and arm64 ELF_ET_DYN_BASE base
changes") broke the behaviour. After the commit elf binary and heap got
mapped above 47-bits.
Use DEFAULT_MAP_WINDOW instead of TASK_SIZE to determine ELF_ET_DYN_BASE so
it's forced to be below 47-bits unconditionally.
Fixes: c715b72c1ba4 ("mm: revert x86_64 and arm64 ELF_ET_DYN_BASE base changes") Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Kees Cook <keescook@chromium.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: linux-mm@kvack.org Cc: Andrew Morton <akpm@linux-foundation.org> Link: https://lkml.kernel.org/r/20171107103804.47341-1-kirill.shutemov@linux.intel.com
Jiri Olsa [Thu, 9 Nov 2017 09:02:10 +0000 (10:02 +0100)]
perf tools: Fix eBPF event specification parsing
Looks like I've reached the new level of stupidity, adding missing braces.
Committer testing:
Given the following eBPF C filter, that will add a record when it
returns true, i.e. when the tv_nsec variable is > 2000ns, should be
built and installed via sys_bpf(), but fails to do so before this patch:
# perf stat -e 'cpu/uops_executed.core,krava/' true
event syntax error: '..cuted.core,krava/'
\___ unknown term
valid terms: cmask,pc,event,edge,in_tx,any,ldlat,inv,umask,in_tx_cp,offcore_rsp,config,config1,config2,name,period
Run 'perf list' for a list of valid events
Usage: perf stat [<options>] [<command>]
-e, --event <event> event selector. use 'perf list' to list available events
#
# perf stat -e 'cpu/uops_executed.core,period=1/' true
Jiri Olsa [Wed, 8 Nov 2017 15:43:09 +0000 (16:43 +0100)]
perf tools: Add "reject" option for parse-events.l
Arnaldo reported broken builds in some distros using a newer flex
release, 2.6.4, found in Alpine Linux 3.6 and Edge, with flex not
spotting the REJECT macro:
CC /tmp/build/perf/util/parse-events-flex.o
util/parse-events.l: In function 'parse_events_lex':
/tmp/build/perf/util/parse-events-flex.c:4734:16: error: \
'reject_used_but_not_detected' undeclared (first use in this function)
It's happening because we put the REJECT under another USER_REJECT macro
in following commit:
9445464bb831 perf tools: Unwind properly location after REJECT
Fortunately flex provides option for force it to use REJECT, adding it
to parse-events.l.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org> Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Reviewed-by: Andi Kleen <andi@firstfloor.org> Tested-by: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Fixes: 9445464bb831 ("perf tools: Unwind properly location after REJECT") Link: http://lkml.kernel.org/n/tip-7kdont984mw12ijk7rji6b8p@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ilya Dryomov [Mon, 6 Nov 2017 10:33:36 +0000 (11:33 +0100)]
rbd: use GFP_NOIO for parent stat and data requests
rbd_img_obj_exists_submit() and rbd_img_obj_parent_read_full() are on
the writeback path for cloned images -- we attempt a stat on the parent
object to see if it exists and potentially read it in to call copyup.
GFP_NOIO should be used instead of GFP_KERNEL here.
Hui Wang [Thu, 9 Nov 2017 00:48:08 +0000 (08:48 +0800)]
ALSA: hda - fix headset mic problem for Dell machines with alc274
Confirmed with Kailang of Realtek, the pin 0x19 is for Headset Mic, and
the pin 0x1a is for Headphone Mic, he suggested to apply
ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to fix this problem. And we
verified applying this FIXUP can fix this problem.
Cc: <stable@vger.kernel.org> Cc: Kailang Yang <kailang@realtek.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
David S. Miller [Thu, 9 Nov 2017 01:03:10 +0000 (10:03 +0900)]
Merge branch 'net-sched-race-fix'
Cong Wang says:
====================
net_sched: close the race between call_rcu() and cleanup_net()
This patchset tries to fix the race between call_rcu() and
cleanup_net() again. Without holding the netns refcnt the
tc_action_net_exit() in netns workqueue could be called before
filter destroy works in tc filter workqueue. This patchset
moves the netns refcnt from tc actions to tcf_exts, without
breaking per-netns tc actions.
Patch 1 reverts the previous fix, patch 2 introduces two new
API's to help to address the bug and the rest patches switch
to the new API's. Please see each patch for details.
I was not able to reproduce this bug, but now after adding
some delay in filter destroy work I manage to trigger the
crash. After this patchset, the crash is not reproducible
any more and the debugging printk's show the order is expected
too.
====================
Fixes: ddf97ccdd7cb ("net_sched: add network namespace support for tc actions") Reported-by: Lucas Bates <lucasb@mojatatu.com> Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:30 +0000 (13:47 -0800)]
cls_u32: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:29 +0000 (13:47 -0800)]
cls_tcindex: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:28 +0000 (13:47 -0800)]
cls_rsvp: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:27 +0000 (13:47 -0800)]
cls_route: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:26 +0000 (13:47 -0800)]
cls_matchall: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:25 +0000 (13:47 -0800)]
cls_fw: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:24 +0000 (13:47 -0800)]
cls_flower: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:23 +0000 (13:47 -0800)]
cls_flow: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:22 +0000 (13:47 -0800)]
cls_cgroup: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:21 +0000 (13:47 -0800)]
cls_bpf: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:20 +0000 (13:47 -0800)]
cls_basic: use tcf_exts_get_net() before call_rcu()
Hold netns refcnt before call_rcu() and release it after
the tcf_exts_destroy() is done.
Note, on ->destroy() path we have to respect the return value
of tcf_exts_get_net(), on other paths it should always return
true, so we don't need to care.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:19 +0000 (13:47 -0800)]
net_sched: introduce tcf_exts_get_net() and tcf_exts_put_net()
Instead of holding netns refcnt in tc actions, we can minimize
the holding time by saving it in struct tcf_exts instead. This
means we can just hold netns refcnt right before call_rcu() and
release it after tcf_exts_destroy() is done.
However, because on netns cleanup path we call tcf_proto_destroy()
too, obviously we can not hold netns for a zero refcnt, in this
case we have to do cleanup synchronously. It is fine for RCU too,
the caller cleanup_net() already waits for a grace period.
For other cases, refcnt is non-zero and we can safely grab it as
normal and release it after we are done.
This patch provides two new API for each filter to use:
tcf_exts_get_net() and tcf_exts_put_net(). And all filters now can
use the following pattern:
if (tcf_exts_get_net()) // <== hold netns refcnt
call_rcu(some_rcu_callback);
else
__destroy_filter();
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Nov 2017 21:47:18 +0000 (13:47 -0800)]
Revert "net_sched: hold netns refcnt for each action"
This reverts commit ceffcc5e254b450e6159f173e4538215cebf1b59.
If we hold that refcnt, the netns can never be destroyed until
all actions are destroyed by user, this breaks our netns design
which we expect all actions are destroyed when we destroy the
whole netns.
Cc: Lucas Bates <lucasb@mojatatu.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Kosina [Wed, 8 Nov 2017 20:18:18 +0000 (21:18 +0100)]
x86/mm: Unbreak modules that rely on external PAGE_KERNEL availability
Commit 7744ccdbc16f0 ("x86/mm: Add Secure Memory Encryption (SME)
support") as a side-effect made PAGE_KERNEL all of a sudden unavailable
to modules which can't make use of EXPORT_SYMBOL_GPL() symbols.
This is because once SME is enabled, sme_me_mask (which is introduced as
EXPORT_SYMBOL_GPL) makes its way to PAGE_KERNEL through _PAGE_ENC,
causing imminent build failure for all the modules which make use of all
the EXPORT-SYMBOL()-exported API (such as vmap(), __vmalloc(),
remap_pfn_range(), ...).
Exporting (as EXPORT_SYMBOL()) interfaces (and having done so for ages)
that take pgprot_t argument, while making it impossible to -- all of a
sudden -- pass PAGE_KERNEL to it, feels rather incosistent.
Restore the original behavior and make it possible to pass PAGE_KERNEL
to all its EXPORT_SYMBOL() consumers.
[ This is all so not wonderful. We shouldn't need that "sme_me_mask"
access at all in all those places that really don't care about that
level of detail, and just want _PAGE_KERNEL or whatever.
We have some similar issues with _PAGE_CACHE_WP and _PAGE_NOCACHE,
both of which hide a "cachemode2protval()" call, and which also ends
up using another EXPORT_SYMBOL(), but at least that only triggers for
the much more rare cases.
Maybe we could move these dynamic page table bits to be generated much
deeper down in the VM layer, instead of hiding them in the macros that
everybody uses.
So this all would merit some cleanup. But not today. - Linus ]
Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Despised-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yonghong Song [Wed, 8 Nov 2017 19:28:45 +0000 (11:28 -0800)]
x86/idt: Remove X86_TRAP_BP initialization in idt_setup_traps()
Commit b70543a0b2b6("x86/idt: Move regular trap init to tables") moves
regular trap init for each trap vector into a table based
initialization. It introduced the initialization for vector X86_TRAP_BP
which was not in the code which it replaced. This breaks uprobe
functionality for x86_32; the probed program segfaults instead of handling
the probe proper.
The reason for this is that TRAP_BP is set up as system interrupt gate
(DPL3) in the early IDT and then replaced by a regular interrupt gate
(DPL0) in idt_setup_traps(). The DPL0 restriction causes the int3 trap
to fail with a #GP resulting in a SIGSEGV of the probed program.
On 64bit this does not cause a problem because the IDT entry is replaced
with a system interrupt gate (DPL3) with interrupt stack afterwards.
Remove X86_TRAP_BP from the def_idts table which is used in
idt_setup_traps(). Remove a redundant entry for X86_TRAP_NMI in def_idts
while at it. Tested on both x86_64 and x86_32.
[ tglx: Amended changelog with a description of the root cause ]
Fixes: b70543a0b2b6("x86/idt: Move regular trap init to tables") Reported-and-tested-by: Yonghong Song <yhs@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: a.p.zijlstra@chello.nl Cc: ast@fb.com Cc: oleg@redhat.com Cc: luto@kernel.org Cc: kernel-team@fb.com Link: https://lkml.kernel.org/r/20171108192845.552709-1-yhs@fb.com
John Johansen [Wed, 8 Nov 2017 16:09:52 +0000 (08:09 -0800)]
apparmor: fix off-by-one comparison on MAXMAPPED_SIG
This came in yesterday, and I have verified our regression tests
were missing this and it can cause an oops. Please apply.
There is a an off-by-one comparision on sig against MAXMAPPED_SIG
that can lead to a read outside the sig_map array if sig
is MAXMAPPED_SIG. Fix this.
Verified that the check is an out of bounds case that can cause an oops.
Revised: add comparison fix to second case Fixes: cd1dbf76b23d ("apparmor: add the ability to mediate signals") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/gpu/drm/i915/i915_gem_gtt.c: In function ‘gen8_ppgtt_insert_4lvl’:
drivers/gpu/drm/i915/i915_gem_gtt.c:938: error: ‘iter.sg’ is used uninitialized in this function
drivers/gpu/drm/i915/i915_gem_gtt.c:939: error: ‘iter.dma’ is used uninitialized in this function
and worse generates invalid code that triggers a GPF:
Recent gccs, such as 4.9, 6.3 or 7.2, do not generate the warning nor do
they explode on use. If we manually create the struct using locals from
the stack, this should eliminate this issue, and does not alter code
generation with gcc-7.2.
Fixes: 894ccebee2b0 ("drm/i915: Micro-optimise gen8_ppgtt_insert_entries()") Reported-by: Kelly French <kfrench@federalhill.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Kelly French <kfrench@federalhill.net> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171106211128.12538-1-chris@chris-wilson.co.uk Tested-by: Kelly French <kfrench@federalhill.net> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit 5684514ba9dc6d7aa932cc53d97d866b2386221f) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Eric Biggers [Tue, 7 Nov 2017 22:29:02 +0000 (22:29 +0000)]
KEYS: fix NULL pointer dereference during ASN.1 parsing [ver #2]
syzkaller reported a NULL pointer dereference in asn1_ber_decoder(). It
can be reproduced by the following command, assuming
CONFIG_PKCS7_TEST_KEY=y:
keyctl add pkcs7_test desc '' @s
The bug is that if the data buffer is empty, an integer underflow occurs
in the following check:
if (unlikely(dp >= datalen - 1))
goto data_overrun_error;
This results in the NULL data pointer being dereferenced.
Fix it by checking for 'datalen - dp < 2' instead.
Also fix the similar check for 'dp >= datalen - n' later in the same
function. That one possibly could result in a buffer overread.
The NULL pointer dereference was reproducible using the "pkcs7_test" key
type but not the "asymmetric" key type because the "asymmetric" key type
checks for a 0-length payload before calling into the ASN.1 decoder but
the "pkcs7_test" key type does not.
Jonas Gorski [Sun, 29 Oct 2017 15:27:19 +0000 (16:27 +0100)]
MIPS: AR7: Defer registration of GPIO
When called from prom init code, ar7_gpio_init() will fail as it will
call gpiochip_add() which relies on a working kmalloc() to alloc
the gpio_desc array and kmalloc is not useable yet at prom init time.
Move ar7_gpio_init() to ar7_register_devices() (a device_initcall)
where kmalloc works.
Josh Poimboeuf [Wed, 8 Nov 2017 02:19:34 +0000 (20:19 -0600)]
x86/unwind: Disable KASAN checking in the ORC unwinder
Fengguang reported a KASAN warning:
Kprobe smoke test: started
==================================================================
BUG: KASAN: stack-out-of-bounds in deref_stack_reg+0xb5/0x11a
Read of size 8 at addr ffff8800001c7cd8 by task swapper/1
The ORC unwinder got confused by some kprobes changes, which isn't
surprising since the runtime code no longer matches vmlinux and the
stack was modified for kretprobes.
Until we have a way for generated code to register changes with the
unwinder, these types of warnings are inevitable. So just disable KASAN
checks for stack accesses in the ORC unwinder.
When we receive a packet on a QMI device in raw IP mode, we should call
skb_reset_mac_header() to ensure that skb->mac_header contains a valid
offset in the packet. While it shouldn't really matter, the packets have
no MAC header and the interface is configured as-such, it seems certain
parts of the network stack expects a "good" value in skb->mac_header.
Without the skb_reset_mac_header() call added in this patch, for example
shaping traffic (using tc) triggers the following oops on the first
received packet:
While the oops is for a 4.9-kernel, I was able to trigger the same oops with
net-next as of yesterday.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode") Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh [Tue, 7 Nov 2017 10:50:07 +0000 (19:50 +0900)]
bonding: fix slave stuck in BOND_LINK_FAIL state
The bonding miimon logic has a flaw, in that a failure of the
rtnl_trylock can cause a slave to become permanently stuck in
BOND_LINK_FAIL state.
The sequence of events to cause this is as follows:
1) bond_miimon_inspect finds that a slave's link is down, and so
calls bond_propose_link_state, setting slave->new_link_state to
BOND_LINK_FAIL, then sets slave->new_link to BOND_LINK_DOWN and returns
non-zero.
2) In bond_mii_monitor, the rtnl_trylock fails, and the timer is
rescheduled. No change is committed.
3) bond_miimon_inspect is called again, but this time the slave
from step 1 has recovered. slave->new_link is reset to NOCHANGE, and, as
slave->link was never changed, the switch enters the BOND_LINK_UP case,
and does nothing. The pending BOND_LINK_FAIL state from step 1 remains
pending, as new_link_state is not reset.
4) The state from step 3 persists until another slave changes link
state and causes bond_miimon_inspect to return non-zero. At this point,
the BOND_LINK_FAIL state change on the slave from steps 1-3 is committed,
and the slave will remain stuck in BOND_LINK_FAIL state even though it
is actually link up.
The remedy for this is to initialize new_link_state on each entry
to bond_miimon_inspect, as is already done with new_link.
Fixes: fb9eb899a6dc ("bonding: handle link transition from FAIL to UP correctly") Reported-by: Alex Sidorenko <alexandre.sidorenko@hpe.com> Reviewed-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Andersson [Tue, 7 Nov 2017 04:50:35 +0000 (20:50 -0800)]
qrtr: Move to postcore_initcall
Registering qrtr with module_init makes the ability of typical platform
code to create AF_QIPCRTR socket during probe a matter of link order
luck. Moving qrtr to postcore_initcall() avoids this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix by simply ignoring the bogus descriptor, as it is optional
for QMI devices anyway.
Fixes: 423ce8caab7e ("net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 6 Nov 2017 14:37:22 +0000 (15:37 +0100)]
net: cdc_ether: fix divide by 0 on bad descriptors
Setting dev->hard_mtu to 0 will cause a divide error in
usbnet_probe. Protect against devices with bogus CDC Ethernet
functional descriptors by ignoring a zero wMaxSegmentSize.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mackerras [Wed, 8 Nov 2017 03:44:04 +0000 (14:44 +1100)]
KVM: PPC: Book3S HV: Fix exclusion between HPT resizing and other HPT updates
Commit 5e9859699aba ("KVM: PPC: Book3S HV: Outline of KVM-HV HPT resizing
implementation", 2016-12-20) added code that tries to exclude any use
or update of the hashed page table (HPT) while the HPT resizing code
is iterating through all the entries in the HPT. It does this by
taking the kvm->lock mutex, clearing the kvm->arch.hpte_setup_done
flag and then sending an IPI to all CPUs in the host. The idea is
that any VCPU task that tries to enter the guest will see that the
hpte_setup_done flag is clear and therefore call kvmppc_hv_setup_htab_rma,
which also takes the kvm->lock mutex and will therefore block until
we release kvm->lock.
However, any VCPU that is already in the guest, or is handling a
hypervisor page fault or hypercall, can re-enter the guest without
rechecking the hpte_setup_done flag. The IPI will cause a guest exit
of any VCPUs that are currently in the guest, but does not prevent
those VCPU tasks from immediately re-entering the guest.
The result is that after resize_hpt_rehash_hpte() has made a HPTE
absent, a hypervisor page fault can occur and make that HPTE present
again. This includes updating the rmap array for the guest real page,
meaning that we now have a pointer in the rmap array which connects
with pointers in the old rev array but not the new rev array. In
fact, if the HPT is being reduced in size, the pointer in the rmap
array could point outside the bounds of the new rev array. If that
happens, we can get a host crash later on such as this one:
To fix this, we tighten up the way that the hpte_setup_done flag is
checked to ensure that it does provide the guarantee that the resizing
code needs. In kvmppc_run_core(), we check the hpte_setup_done flag
after disabling interrupts and refuse to enter the guest if it is
clear (for a HPT guest). The code that checks hpte_setup_done and
calls kvmppc_hv_setup_htab_rma() is moved from kvmppc_vcpu_run_hv()
to a point inside the main loop in kvmppc_run_vcpu(), ensuring that
we don't just spin endlessly calling kvmppc_run_core() while
hpte_setup_done is clear, but instead have a chance to block on the
kvm->lock mutex.
Finally we also check hpte_setup_done inside the region in
kvmppc_book3s_hv_page_fault() where the HPTE is locked and we are about
to update the HPTE, and bail out if it is clear. If another CPU is
inside kvm_vm_ioctl_resize_hpt_commit) and has cleared hpte_setup_done,
then we know that either we are looking at a HPTE
that resize_hpt_rehash_hpte() has not yet processed, which is OK,
or else we will see hpte_setup_done clear and refuse to update it,
because of the full barrier formed by the unlock of the HPTE in
resize_hpt_rehash_hpte() combined with the locking of the HPTE
in kvmppc_book3s_hv_page_fault().
Hangbin Liu [Mon, 6 Nov 2017 01:01:57 +0000 (09:01 +0800)]
bonding: discard lowest hash bit for 802.3ad layer3+4
After commit 07f4c90062f8 ("tcp/dccp: try to not exhaust ip_local_port_range
in connect()"), we will try to use even ports for connect(). Then if an
application (seen clearly with iperf) opens multiple streams to the same
destination IP and port, each stream will be given an even source port.
So the bonding driver's simple xmit_hash_policy based on layer3+4 addressing
will always hash all these streams to the same interface. And the total
throughput will limited to a single slave.
Change the tcp code will impact the whole tcp behavior, only for bonding
usage. Paolo Abeni suggested fix this by changing the bonding code only,
which should be more reasonable, and less impact.
Fix this by discarding the lowest hash bit because it contains little entropy.
After the fix we can re-balance between slaves.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices.
In order to identify a touchscreen device, Android for example, seems to
already depend on INPUT_PROP_DIRECT to be present in drivers. udev still
checks for either BTN_TOUCH or INPUT_PROP_DIRECT. Checking for BTN_TOUCH
however can quite easily lead to false positives; it's a code that not only
touchscreen device drivers use.
According to the documentation, touchscreen drivers should have this
property set and in order to make life easy for userspace, let's set it.
Signed-off-by: Martin Kepplinger <martink@posteo.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
net/mlx5e/core/en_fs: fix pointer dereference after free in mlx5e_execute_l2_action
hn is being kfree'd in mlx5e_del_l2_from_hash and then dereferenced
by accessing hn->ai.addr
Fix this by copying the MAC address into a local variable for its safe use
in all possible execution paths within function mlx5e_execute_l2_action.
Addresses-Coverity-ID: 1417789 Fixes: eeb66cdb6826 ("net/mlx5: Separate between E-Switch and MPFS") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Sat, 4 Nov 2017 12:33:47 +0000 (12:33 +0000)]
net: mvpp2: Prevent userspace from changing TX affinities
The mvpp2 driver can't cope at all with the TX affinities being
changed from userspace, and spit an endless stream of
[ 91.779920] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.779930] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780402] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780406] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780415] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
[ 91.780418] mvpp2 f4000000.ethernet eth2: wrong cpu on the end of Tx processing
rendering the box completely useless (I've measured around 600k
interrupts/s on a 8040 box) once irqbalance kicks in and start
doing its job.
Obviously, the driver was never designed with this in mind. So let's
work around the problem by preventing userspace from interacting
with these interrupts altogether.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MAINTAINERS: Remove Gabriele Paoloni as HiSilicon PCI maintainer
Gabriele is now moving to a different role, so remove him as HiSilicon PCI
maintainer.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
[bhelgaas: Thanks for all your help, Gabriele, and best wishes!] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Borislav Petkov [Tue, 7 Nov 2017 16:37:24 +0000 (17:37 +0100)]
drivers/ide-cd: Handle missing driver data during status check gracefully
The 0day bot reports the below failure which happens occasionally, with
their randconfig testing (once every ~100 boots). The Code points at
the private pointer ->driver_data being NULL, which hints at a race of
sorts where the private driver_data descriptor has disappeared by the
time we get to run the workqueue.
So let's check that pointer before we continue with issuing the command
to the drive.
This fix is of the brown paper bag nature but considering that IDE is
long deprecated, let's do that so that random testing which happens to
enable CONFIG_IDE during randconfig builds, doesn't fail because of
this.
Besides, failing the TEST_UNIT_READY command because the drive private
data is gone is something which we could simply do anyway, to denote
that there was a problem communicating with the device.
This commit added a call to sysfs_notify() from within
scsi_device_set_state(), which in turn turns out to make libata very
unhappy, because ata_eh_detach_dev() does
Takashi Iwai [Tue, 7 Nov 2017 15:05:24 +0000 (16:05 +0100)]
ALSA: seq: Fix OSS sysex delivery in OSS emulation
The SYSEX event delivery in OSS sequencer emulation assumed that the
event is encoded in the variable-length data with the straight
buffering. This was the normal behavior in the past, but during the
development, the chained buffers were introduced for carrying more
data, while the OSS code was left intact. As a result, when a SYSEX
event with the chained buffer data is passed to OSS sequencer port,
it may end up with the wrong memory access, as if it were having a too
large buffer.
This patch addresses the bug, by applying the buffer data expansion by
the generic snd_seq_dump_var_event() helper function.
Pavel Tatashin [Sat, 28 Oct 2017 00:11:00 +0000 (20:11 -0400)]
x86/smpboot: Make optimization of delay calibration work correctly
If the TSC has constant frequency then the delay calibration can be skipped
when it has been calibrated for a package already. This is checked in
calibrate_delay_is_known(), but that function is buggy in two aspects:
which is obviously the reverse of the intended check and the check for the
sibling mask cannot work either because the topology links have not been
set up yet.
Correct the condition and move the call to set_cpu_sibling_map() before
invoking calibrate_delay() so the sibling check works correctly.
[ tglx: Rewrote changelong ]
Fixes: c25323c07345 ("x86/tsc: Use topology functions") Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: peterz@infradead.org Cc: bob.picco@oracle.com Cc: steven.sistare@oracle.com Cc: daniel.m.jordan@oracle.com Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20171028001100.26603-1-pasha.tatashin@oracle.com
ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell XPS13 9360
At least one Dell XPS13 9360 is reported to have serious issues with
the Low Power S0 Idle _DSM interface and since this machine model
generally can do ACPI S3 just fine, add a blacklist entry to disable
that interface for Dell XPS13 9360.
Fixes: 8110dd281e15 (ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems) Link: https://bugzilla.kernel.org/show_bug.cgi?id=196907 Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 4.13+ <stable@vger.kernel.org> # 4.13+
Linus Torvalds [Mon, 6 Nov 2017 20:26:49 +0000 (12:26 -0800)]
Merge branch 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"Another fix for a really old bug.
It only affects drain_workqueue() which isn't used often and even then
triggers only during a pretty small race window, so it isn't too
surprising that it stayed hidden for so long.
The fix is straight-forward and low-risk. Kudos to Li Bin for
reporting and fixing the bug"
* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Fix NULL pointer dereference
Currently we are leaking addresses from the kernel to user space. This
script is an attempt to find some of those leakages. Script parses
`dmesg` output and /proc and /sys files for hex strings that look like
kernel addresses.
Only works for 64 bit kernels, the reason being that kernel addresses on
64 bit kernels have 'ffff' as the leading bit pattern making greping
possible. On 32 kernels we don't have this luxury.
Scripts is _slightly_ smarter than a straight grep, we check for false
positives (all 0's or all 1's, and vsyscall start/finish addresses).
[ I think there is a lot of room for improvement here, but it's already
useful, so I'm merging it as-is. The whole "hash %p format" series is
expected to go into 4.15, but will not fix %x users, and will not
incentivize people to look at what they are leaking. - Linus ]
Signed-off-by: Tobin C. Harding <me@tobin.cc> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Mon, 6 Nov 2017 19:16:50 +0000 (20:16 +0100)]
ALSA: seq: Avoid invalid lockdep class warning
The recent fix for adding rwsem nesting annotation was using the given
"hop" argument as the lock subclass key. Although the idea itself
works, it may trigger a kernel warning like:
BUG: looking up invalid subclass: 8
....
since the lockdep has a smaller number of subclasses (8) than we
currently allow for the hops there (10).
The current definition is merely a sanity check for avoiding the too
deep delivery paths, and the 8 hops are already enough. So, as a
quick fix, just follow the max hops as same as the max lockdep
subclasses.
projects / mirror_ubuntu-bionic-kernel.git / log