Dmitry Torokhov [Sat, 25 Oct 2014 00:20:27 +0000 (17:20 -0700)]
Input: psmouse - remove unneeded check in psmouse_reconnect()
psmouse_reconnect() will not be called if psmouse driver is not bound to
the serio port, so there is no point in checking that. Also, as coded, it
introduces potential NULL dereference in psmouse_dbg() in case psmouse is
indeed NULL. Let's just remove it.
Dmitry Torokhov [Fri, 24 Oct 2014 22:33:53 +0000 (15:33 -0700)]
Input: vsxxxaa - fix code dropping bytes from queue
I believe the intent of the code was to drop oldest bytes from the queue,
not the latest if we drop one byte and both latest and some oldest of we
are dropping more than one.
Input: wm97xx - adapt parameters to tosa touchscreen.
Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.
Input: soc_button_array - update calls to gpiod_get*()
Add the new flags argument to calls of (devm_)gpiod_get*().
Currently both forms (with or without the flags argument) are valid thanks
to transitional macros in <linux/gpio/consumer.h>. These macros will be
removed once all consumers are updated and the flags argument will become
compulsory.
Chang Huaixin [Thu, 16 Oct 2014 20:33:24 +0000 (13:33 -0700)]
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
xenkbd_disconnect_backend doesn't free grant table entry. This bug affects
live migration.
xenkbd_disconnect_backend uses gnttab_end_foreign_access_ref to handle
grant table entry which doesn't really free an entry.
Thus every time we do xenkbd_resume, grant table entry increses by one. As
an grant table entry occupies 8 bytes, an grant table page has at most 512
entries. Every 512 times we do xenkdb_resume, grant table pages increses by
one.
After around 3500 times of live migration, grant table pages will increase
by 7, causing too many pages to populate and hitting max_pages limit when
assigning pages.Thus assign_pages will fail, so will live migration.
Andreas Bosch [Wed, 15 Oct 2014 17:44:50 +0000 (10:44 -0700)]
Input: alps - fix v4 button press recognition
Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768 Fixes: 02d04254a5df ("Input: alps - use struct input_mt_pos to track coordinates") Signed-off-by: Andreas Bosch <linux@progandy.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Fri, 10 Oct 2014 19:19:03 +0000 (12:19 -0700)]
Input: i8042 - disable active multiplexing by default
Active multiplexing is a nice feature as it allows several pointing devices
(such as touchpad and external mouse) use their native protocols at the
same time. Unfortunately many manufacturers do not implement the feature
properly even though they advertise it. The problematic implementations are
never fixed, since Windows by default does not use this mode, and move from
one BIOS/model of laptop to another. When active multiplexing is broken
turning it on usually results in touchpad, keyboard, or both unresponsive.
With PS/2 usage on decline (most of PS/2 devices in use nowadays are
internal laptop touchpads), I expect number of users who have laptops with
working MUX implementation, docking stations with external PS/2 ports, and
who are still using external PS/2 mice, to be rather small. Let's flip the
default to be OFF and allow activating it through i8042.nomux=0 kernel
option. We'll also keep DMI table where we can record known good models.
Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sjoerd Simons [Wed, 8 Oct 2014 18:38:21 +0000 (11:38 -0700)]
Input: cros_ec_keyb - add of match table
To enable the cros_ec_keyb driver to be auto-loaded when build as
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Dmitry Torokhov [Mon, 6 Oct 2014 17:55:49 +0000 (10:55 -0700)]
Input: evdev - fix EVIOCG{type} ioctl
The 'max' size passed into the function is measured in number of bits
(KEY_MAX, LED_MAX, etc) so we need to convert it accordingly before trying
to copy the data out, otherwise we will try copying too much and end up
with up with a page fault.
Reported-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: Pavel Machek <pavel@ucw.cz> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Sun, 5 Oct 2014 17:16:11 +0000 (10:16 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of two small fixes, both to code which went in during
the merge window: cxgb4i has a scheduling in atomic bug in its new
ipv6 code and uas fails to work properly with the new scsi-mq code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] uas: disable use of blk-mq I/O path
[SCSI] cxgb4i: avoid holding mutex in interrupt context
Linus Torvalds [Sat, 4 Oct 2014 16:32:47 +0000 (09:32 -0700)]
Merge tag 'tiny/kconfig-for-3.17' of https://git.kernel.org/pub/scm/linux/kernel/git/josh/linux
Pull kconfig fixes for tiny setups from Josh Triplett:
"Two Kconfig bugfixes for 3.17 related to tinification. These fixes
make the Kconfig "General Setup" menu much more usable"
* tag 'tiny/kconfig-for-3.17' of https://git.kernel.org/pub/scm/linux/kernel/git/josh/linux:
init/Kconfig: Fix HAVE_FUTEX_CMPXCHG to not break up the EXPERT menu
init/Kconfig: Hide printk log config if CONFIG_PRINTK=n
Josh Triplett [Fri, 3 Oct 2014 23:19:24 +0000 (16:19 -0700)]
init/Kconfig: Fix HAVE_FUTEX_CMPXCHG to not break up the EXPERT menu
commit 03b8c7b623c80af264c4c8d6111e5c6289933666 ("futex: Allow
architectures to skip futex_atomic_cmpxchg_inatomic() test") added the
HAVE_FUTEX_CMPXCHG symbol right below FUTEX. This placed it right in
the middle of the options for the EXPERT menu. However,
HAVE_FUTEX_CMPXCHG does not depend on EXPERT or FUTEX, so Kconfig stops
placing items in the EXPERT menu, and displays the remaining several
EXPERT items (starting with EPOLL) directly in the General Setup menu.
Since both users of HAVE_FUTEX_CMPXCHG only select it "if FUTEX", make
HAVE_FUTEX_CMPXCHG itself depend on FUTEX. With this change, the
subsequent items display as part of the EXPERT menu again; the EMBEDDED
menu now appears as the next top-level item in the General Setup menu,
which makes General Setup much shorter and more usable.
Linus Torvalds [Fri, 3 Oct 2014 20:31:57 +0000 (13:31 -0700)]
Merge tag 'trace-fixes-v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull trace ring buffer iterator fix from Steven Rostedt:
"While testing some new changes for 3.18, I kept hitting a bug every so
often in the ring buffer. At first I thought it had to do with some
of the changes I was working on, but then testing something else I
realized that the bug was in 3.17 itself. I ran several bisects as
the bug was not very reproducible, and finally came up with the commit
that I could reproduce easily within a few minutes, and without the
change I could run the tests over an hour without issue. The change
fit the bug and I figured out a fix. That bad commit was:
Commit 651e22f2701b "ring-buffer: Always reset iterator to reader page"
This commit fixed a bug, but in the process created another one. It
used the wrong value as the cached value that is used to see if things
changed while an iterator was in use. This made it look like a change
always happened, and could cause the iterator to go into an infinite
loop"
* tag 'trace-fixes-v3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Fix infinite spin in reading buffer
Linus Torvalds [Fri, 3 Oct 2014 20:09:57 +0000 (13:09 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs/smb3 fixes from Steve French:
"Fix for CIFS/SMB3 oops on reconnect during readpages (3.17 regression)
and for incorrectly closing file handle in symlink error cases"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix readpages retrying on reconnects
Fix problem recognizing symlinks
Linus Torvalds [Fri, 3 Oct 2014 15:31:14 +0000 (08:31 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too major or scary.
One i915 regression fix, nouveau has a tmds regression fix, along with
a regression fix for the runtime pm code for optimus laptops not
restoring the display hw correctly"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: make sure display hardware is reinitialised on runtime resume
drm/nouveau: punt fbcon resume out to a workqueue
drm/nouveau: fix regression on original nv50 board
drm/nv50/disp: fix dpms regression on certain boards
drm/i915: Flush the PTEs after updating them before suspend
The uas driver uses the block layer tag for USB3 stream IDs. With
blk-mq we can get larger tag numbers that the queue depth, which breaks
this assumption. A fix is under way for 3.18, but sits on top of
large changes so can't easily be backported. Set the disable_blk_mq
path so that a uas device can't easily crash the system when using
blk-mq for SCSI.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Fri, 3 Oct 2014 01:47:28 +0000 (18:47 -0700)]
Merge tag 'pm+acpi-3.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three regression fixes (cpufreq core, pcc-cpufreq, i915 /
ACPI) and one trivial fix for a callback return value mismatch in the
cpufreq integrator driver.
Specifics:
- A recent cpufreq core fix went too far and introduced a regression
in the system suspend code path. Fix from Viresh Kumar.
- An ACPI-related commit in the i915 driver that fixed backlight
problems for some Thinkpads inadvertently broke a Dell machine (in
3.16). Fix from Aaron Lu.
- The pcc-cpufreq driver was broken during the 3.15 cycle by a commit
that put wait_event() under a spinlock by mistake. Fix that
(Rafael J Wysocki).
- The return value type of integrator_cpufreq_remove() is void, but
should be int. Fix from Arnd Bergmann"
* tag 'pm+acpi-3.17-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: update 'cpufreq_suspended' after stopping governors
ACPI / i915: Update the condition to ignore firmware backlight change request
cpufreq: integrator: fix integrator_cpufreq_remove return type
cpufreq: pcc-cpufreq: Fix wait_event() under spinlock
Andy Gross [Mon, 29 Sep 2014 22:00:51 +0000 (17:00 -0500)]
i2c: qup: Fix order of runtime pm initialization
The runtime pm calls need to be done before populating the children via the
i2c_add_adapter call. If this is not done, a child can run into issues trying
to do i2c read/writes due to the pm_runtime_sync failing.
Signed-off-by: Andy Gross <agross@codeaurora.org> Reviewed-by: Felipe Balbi <balbi@ti.com> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
i2cdetect -q was broken (everything was a false positive, and no transfers were
actually being sent over i2c). The way it works is by sending a 0 length write
request and checking for NACK. This patch fixes the 0 length writes and actually
sends them.
Reported-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Alexandru M Stan <amstan@chromium.org> Tested-by: Doug Anderson <dianders@chromium.org> Tested-by: Max Schwarz <max.schwarz@online.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Linus Torvalds [Thu, 2 Oct 2014 23:29:19 +0000 (16:29 -0700)]
Merge branch 'akpm' (fixes from Andrew Morton)
Merge fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: page_alloc: fix zone allocation fairness on UP
perf: fix perf bug in fork()
MAINTAINERS: change git URL for mpc5xxx tree
mm: memcontrol: do not iterate uninitialized memcgs
ocfs2/dlm: should put mle when goto kill in dlm_assert_master_handler
Johannes Weiner [Thu, 2 Oct 2014 23:21:10 +0000 (16:21 -0700)]
mm: page_alloc: fix zone allocation fairness on UP
The zone allocation batches can easily underflow due to higher-order
allocations or spills to remote nodes. On SMP that's fine, because
underflows are expected from concurrency and dealt with by returning 0.
But on UP, zone_page_state will just return a wrapped unsigned long,
which will get past the <= 0 check and then consider the zone eligible
until its watermarks are hit.
Commit 3a025760fc15 ("mm: page_alloc: spill to remote nodes before
waking kswapd") already made the counter-resetting use
atomic_long_read() to accomodate underflows from remote spills, but it
didn't go all the way with it.
Make it clear that these batches are expected to go negative regardless
of concurrency, and use atomic_long_read() everywhere.
Fixes: 81c0a2bb515f ("mm: page_alloc: fair zone allocator policy") Reported-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Leon Romanovsky <leon@leon.nu> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Mel Gorman <mgorman@suse.de> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Thu, 2 Oct 2014 23:17:02 +0000 (16:17 -0700)]
perf: fix perf bug in fork()
Oleg noticed that a cleanup by Sylvain actually uncovered a bug; by
calling perf_event_free_task() when failing sched_fork() we will not yet
have done the memset() on ->perf_event_ctxp[] and will therefore try and
'free' the inherited contexts, which are still in use by the parent
process. This is bad..
Johannes Weiner [Thu, 2 Oct 2014 23:16:57 +0000 (16:16 -0700)]
mm: memcontrol: do not iterate uninitialized memcgs
The cgroup iterators yield css objects that have not yet gone through
css_online(), but they are not complete memcgs at this point and so the
memcg iterators should not return them. Commit d8ad30559715 ("mm/memcg:
iteration skip memcgs not yet fully initialized") set out to implement
exactly this, but it uses CSS_ONLINE, a cgroup-internal flag that does
not meet the ordering requirements for memcg, and so the iterator may
skip over initialized groups, or return partially initialized memcgs.
The cgroup core can not reasonably provide a clear answer on whether the
object around the css has been fully initialized, as that depends on
controller-specific locking and lifetime rules. Thus, introduce a
memcg-specific flag that is set after the memcg has been initialized in
css_online(), and read before mem_cgroup_iter() callers access the memcg
members.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Oct 2014 23:10:38 +0000 (16:10 -0700)]
Merge tag 'media/v3.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"One last time regression fix at em28xx. The removal of .reset_resume
broke suspend/resume on this driver for some devices.
There are more fixes to be done for em28xx suspend/resume to be better
handled, but I'm opting to let them to stay for a while at the media
devel tree, in order to get more tests. So, for now, let's just
revert this patch"
* tag 'media/v3.17-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "[media] media: em28xx - remove reset_resume interface"
Commit 651e22f2701b "ring-buffer: Always reset iterator to reader page"
fixed one bug but in the process caused another one. The reset is to
update the header page, but that fix also changed the way the cached
reads were updated. The cache reads are used to test if an iterator
needs to be updated or not.
A ring buffer iterator, when created, disables writes to the ring buffer
but does not stop other readers or consuming reads from happening.
Although all readers are synchronized via a lock, they are only
synchronized when in the ring buffer functions. Those functions may
be called by any number of readers. The iterator continues down when
its not interrupted by a consuming reader. If a consuming read
occurs, the iterator starts from the beginning of the buffer.
The way the iterator sees that a consuming read has happened since
its last read is by checking the reader "cache". The cache holds the
last counts of the read and the reader page itself.
Commit 651e22f2701b changed what was saved by the cache_read when
the rb_iter_reset() occurred, making the iterator never match the cache.
Then if the iterator calls rb_iter_reset(), it will go into an
infinite loop by checking if the cache doesn't match, doing the reset
and retrying, just to see that the cache still doesn't match! Which
should never happen as the reset is suppose to set the cache to the
current value and there's locks that keep a consuming reader from
having access to the data.
Fixes: 651e22f2701b "ring-buffer: Always reset iterator to reader page" Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Linus Torvalds [Thu, 2 Oct 2014 19:23:10 +0000 (12:23 -0700)]
Merge branch 'parisc-3.17-8' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"One late but trivial patch to fix the serial console on parisc
machines which got broken during the 3.17 release cycle"
* 'parisc-3.17-8' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix serial console for machines with serial port on superio chip
Pavel Shilovsky [Thu, 2 Oct 2014 16:13:35 +0000 (20:13 +0400)]
CIFS: Fix readpages retrying on reconnects
If we got a reconnect error from async readv we re-add pages back
to page_list and continue loop. That is wrong because these pages
have been already added to the pagecache but page_list has pages that
have not been added to the pagecache yet. This ends up with a general
protection fault in put_pages after readpages. Fix it by not retrying
the read of these pages and falling back to readpage instead.
Fixes debian bug 762306
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Steve French [Thu, 25 Sep 2014 06:26:55 +0000 (01:26 -0500)]
Fix problem recognizing symlinks
Changeset eb85d94bd introduced a problem where if a cifs open
fails during query info of a file we
will still try to close the file (happens with certain types
of reparse points) even though the file handle is not valid.
In addition for SMB2/SMB3 we were not mapping the return code returned
by Windows when trying to open a file (like a Windows NFS symlink)
which is a reparse point.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org> CC: stable <stable@vger.kernel.org> #v3.13+
Linus Torvalds [Thu, 2 Oct 2014 18:57:52 +0000 (11:57 -0700)]
Merge branch 'numa-migration-fixes' (fixes from Mel Gorman)
Merge NUMA balancing related fixlets from Mel Gorman:
"There were a few minor changes so am resending just the two patches
that are mostly likely to affect the bug Dave and Sasha saw and marked
them for stable.
I'm less confident it will address Sasha's problem because while I
have not kept up to date, I believe he's also seeing memory corruption
issues in next from an unknown source. Still, it would be nice to see
how they affect trinity testing.
I'll send the MPOL_MF_LAZY patch separately because it's not urgent"
* emailed patches from Mel Gorman <mgorman@suse.de>:
mm: numa: Do not mark PTEs pte_numa when splitting huge pages
mm: migrate: Close race between migration completion and mprotect
Mel Gorman [Thu, 2 Oct 2014 18:47:42 +0000 (19:47 +0100)]
mm: numa: Do not mark PTEs pte_numa when splitting huge pages
This patch reverts 1ba6e0b50b ("mm: numa: split_huge_page: transfer the
NUMA type from the pmd to the pte"). If a huge page is being split due
a protection change and the tail will be in a PROT_NONE vma then NUMA
hinting PTEs are temporarily created in the protected VMA.
VM_RW|VM_PROTNONE
|-----------------|
^
split here
In the specific case above, it should get fixed up by change_pte_range()
but there is a window of opportunity for weirdness to happen. Similarly,
if a huge page is shrunk and split during a protection update but before
pmd_numa is cleared then a pte_numa can be left behind.
Instead of adding complexity trying to deal with the case, this patch
will not mark PTEs NUMA when splitting a huge page. NUMA hinting faults
will not be triggered which is marginal in comparison to the complexity
in dealing with the corner cases during THP split.
Cc: stable@vger.kernel.org Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 2 Oct 2014 18:47:41 +0000 (19:47 +0100)]
mm: migrate: Close race between migration completion and mprotect
A migration entry is marked as write if pte_write was true at the time the
entry was created. The VMA protections are not double checked when migration
entries are being removed as mprotect marks write-migration-entries as
read. It means that potentially we take a spurious fault to mark PTEs write
again but it's straight-forward. However, there is a race between write
migrations being marked read and migrations finishing. This potentially
allows a PTE to be write that should have been read. Close this race by
double checking the VMA permissions using maybe_mkwrite when migration
completes.
[torvalds@linux-foundation.org: use maybe_mkwrite] Cc: stable@vger.kernel.org Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Oct 2014 16:42:28 +0000 (09:42 -0700)]
Merge tag 'sound-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few pending bits of random fixes in ASoC. Nothing exciting,
but would be nice to be merged in 3.17, as most of them are also for
stable kernels"
* tag 'sound-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: ssm2602: do not hardcode type to SSM2602
ASoC: core: fix possible ZERO_SIZE_PTR pointer dereferencing error.
MAINTAINERS: add atmel audio alsa driver maintainer entry
ASoC: rt286: Fix sync function
ASoC: rt286: Correct default value
ASoC: soc-compress: fix double unlock of fe card mutex
ASoC: fsl_ssi: fix kernel panic in probe function
Dave Airlie [Thu, 2 Oct 2014 04:48:20 +0000 (14:48 +1000)]
Merge branch 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
A few regression fixes, the runpm ones dating back to 3.15. Also a fairly severe TMDS regression that effected a lot of GF8/9/GT2xx users.
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: make sure display hardware is reinitialised on runtime resume
drm/nouveau: punt fbcon resume out to a workqueue
drm/nouveau: fix regression on original nv50 board
drm/nv50/disp: fix dpms regression on certain boards
1) Don't halt the firmware in r8152 driver, from Hayes Wang.
2) Handle full sized 802.1ad frames in bnx2 and tg3 drivers properly,
from Vlad Yasevich.
3) Don't sleep while holding tx_clean_lock in netxen driver, fix from
Manish Chopra.
4) Certain kinds of ipv6 routes can end up endlessly failing the route
validation test, causing it to be re-looked up over and over again.
This particularly kills input route caching in TCP sockets. Fix
from Hannes Frederic Sowa.
5) netvsc_start_xmit() has a use-after-free access to skb->len, fix
from K Y Srinivasan.
6) Fix matching of inverted containers in ematch module, from Ignacy
Gawędzki.
7) Aggregation of GRO frames via SKB ->frag_list for linear skbs isn't
handled properly, regression fix from Eric Dumazet.
8) Don't test return value of ipv4_neigh_lookup(), which returns an
error pointer, against NULL. From WANG Cong.
9) Fix an old regression where we mistakenly allow a double add of the
same tunnel. Fixes from Steffen Klassert.
10) macvtap device delete and open can run in parallel and corrupt lists
etc., fix from Vlad Yasevich.
11) Fix build error with IPV6=m NETFILTER_XT_TARGET_TPROXY=y, from Pablo
Neira Ayuso.
12) rhashtable_destroy() triggers lockdep splats, fix also from Pablo.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
bna: Update Maintainer Email
r8152: disable power cut for RTL8153
r8152: remove clearing bp
bnx2: Correctly receive full sized 802.1ad fragmes
tg3: Allow for recieve of full-size 8021AD frames
r8152: fix setting RTL8152_UNPLUG
netxen: Fix bug in Tx completion path.
netxen: Fix BUG "sleeping function called from invalid context"
ipv6: remove rt6i_genid
hyperv: Fix a bug in netvsc_start_xmit()
net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected
ematch: Fix matching of inverted containers.
gro: fix aggregation for skb using frag_list
neigh: check error pointer instead of NULL for ipv4_neigh_lookup()
ip6_gre: Return an error when adding an existing tunnel.
ip6_vti: Return an error when adding an existing tunnel.
ip6_tunnel: Return an error when adding an existing tunnel.
ip6gre: add a rtnl link alias for ip6gretap
net/mlx4_core: Allow not to specify probe_vf in SRIOV IB mode
r8152: fix the carrier off when autoresuming
...
NeilBrown [Thu, 2 Oct 2014 03:45:00 +0000 (13:45 +1000)]
md/raid5: disable 'DISCARD' by default due to safety concerns.
It has come to my attention (thanks Martin) that 'discard_zeroes_data'
is only a hint. Some devices in some cases don't do what it
says on the label.
The use of DISCARD in RAID5 depends on reads from discarded regions
being predictably zero. If a write to a previously discarded region
performs a read-modify-write cycle it assumes that the parity block
was consistent with the data blocks. If all were zero, this would
be the case. If some are and some aren't this would not be the case.
This could lead to data corruption after a device failure when
data needs to be reconstructed from the parity.
As we cannot trust 'discard_zeroes_data', ignore it by default
and so disallow DISCARD on all raid4/5/6 arrays.
As many devices are trustworthy, and as there are benefits to using
DISCARD, add a module parameter to over-ride this caution and cause
DISCARD to work if discard_zeroes_data is set.
If a site want to enable DISCARD on some arrays but not on others they
should select DISCARD support at the filesystem level, and set the
raid456 module parameter.
raid456.devices_handle_discard_safely=Y
As this is a data-safety issue, I believe this patch is suitable for
-stable.
DISCARD support for RAID456 was added in 3.7
Cc: Shaohua Li <shli@kernel.org> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Heinz Mauelshagen <heinzm@redhat.com> Cc: stable@vger.kernel.org (3.7+) Acked-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Fixes: 620125f2bf8ff0c4969b79653b54d7bcc9d40637 Signed-off-by: NeilBrown <neilb@suse.de>
Ben Skeggs [Thu, 2 Oct 2014 03:22:27 +0000 (13:22 +1000)]
drm/nouveau: make sure display hardware is reinitialised on runtime resume
Linus commit 05c63c2ff23a80b654d6c088ac3ba21628db0173 modified the
runtime suspend/resume paths to skip over display-related tasks to
avoid locking issues on resume.
Unfortunately, this resulted in the display hardware being left in
a partially initialised state, preventing subsequent modesets from
completing.
This commit unifies the (many) suspend/resume paths, bringing back
display (and fbcon) handling in the runtime paths.
Ben Skeggs [Wed, 1 Oct 2014 01:11:25 +0000 (11:11 +1000)]
drm/nouveau: punt fbcon resume out to a workqueue
Preparation for some runtime pm fixes. Currently we skip over fbcon
suspend/resume in the runtime path, which causes issues on resume if
fbcon tries to write to the framebuffer before the BAR subdev has
been resumed to restore the BAR1 VM setup.
As we might be woken up via a sysfs connector, we are unable to call
fb_set_suspend() in the resume path as it could make its way down to
a modeset and cause all sorts of locking hilarity.
To solve this, we'll just delay the fbcon resume to a workqueue.
Ben Skeggs [Wed, 1 Oct 2014 02:46:14 +0000 (12:46 +1000)]
drm/nouveau: fix regression on original nv50 board
Xorg (and any non-DRM client really) doesn't have permission to directly
touch VRAM on nv50 and up, which the fence code prior to g84 depends on.
It's less invasive to temporarily grant it premission to do so, as it
previously did, than it is to rework fencenv50 to use the VM. That
will come later on.
hayeswang [Wed, 1 Oct 2014 05:25:10 +0000 (13:25 +0800)]
r8152: remove clearing bp
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2: Correctly receive full sized 802.1ad fragmes
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com> CC: Dept-HSGLinuxNICDev@qlogic.com Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com> CC: Prashant Sreedharan <prashant@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 Oct 2014 20:22:00 +0000 (13:22 -0700)]
Merge branch 'for-3.17' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfix from Bruce Fields:
"This fixes a data corruption bug introduced by the v3.16 xdr encoding
rewrite. I haven't managed to reproduce it myself yet, but it's
apparently not hard to hit given the right workload"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix corruption of NFSv4 read data
[SCSI] cxgb4i: avoid holding mutex in interrupt context
cxgbi_inet6addr_handler() can be called in interrupt context, so use rcu
protected list while finding netdev. This is observed as a scheduling in
atomic oops when running over ipv6.
Fixes: fc8d0590d914 ("libcxgbi: Add ipv6 api to driver") Fixes: 759a0cc5a3e1 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api") Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: Karen Xie <kxie@chelsio.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Wed, 1 Oct 2014 02:52:08 +0000 (19:52 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Some further ARM fixes:
- another build fix for the kprobes test code
- a fix for no kuser helpers for the set_tls code, which oopsed on
noMMU hardware
- a fix for alignment handler with neon opcodes being misinterpreted
- turning off the hardware access support, which is not implemented
- a build fix for the v7 coherency exiting code, which can be built
in non-v7 environments (but still only executed on v7 CPUs)"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8179/1: kprobes-test: Fix compile error "bad immediate value for offset"
ARM: 8178/1: fix set_tls for !CONFIG_KUSER_HELPERS
ARM: 8177/1: cacheflush: Fix v7_exit_coherency_flush exynos build breakage on ARMv6
ARM: 8165/1: alignment: don't break misaligned NEON load/store
ARM: 8164/1: mm: clear SCTLR.HA instead of setting it for LPAE
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 Sep 2014 20:22:51 +0000 (16:22 -0400)]
Merge branch 'netxen'
Manish Chopra says:
====================
netxen: Bug fixes.
This series fixes some TX specific issues.
* Move spin_lock(tx_clean_lock) in down path to fix
atomic sleep bug (Reported by Mike Galbraith).
* Fix hang in interface down while running traffic.
Please consider applying this to 'net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: Fix BUG "sleeping function called from invalid context"
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
J. Bruce Fields [Wed, 24 Sep 2014 20:32:34 +0000 (16:32 -0400)]
nfsd4: fix corruption of NFSv4 read data
The calculation of page_ptr here is wrong in the case the read doesn't
start at an offset that is a multiple of a page.
The result is that nfs4svc_encode_compoundres sets rq_next_page to a
value one too small, and then the loop in svc_free_res_pages may
incorrectly fail to clear a page pointer in rq_respages[].
Pages left in rq_respages[] are available for the next rpc request to
use, so xdr data may be written to that page, which may hold data still
waiting to be transmitted to the client or data in the page cache.
The observed result was silent data corruption seen on an NFSv4 client.
We tag this as "fixing" 05638dc73af2 because that commit exposed this
bug, though the incorrect calculation predates it.
Particular thanks to Andrea Arcangeli and David Gilbert for analysis and
testing.
Fixes: 05638dc73af2 "nfsd4: simplify server xdr->next_page use" Cc: stable@vger.kernel.org Reported-by: Andrea Arcangeli <aarcange@redhat.com> Tested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
cpufreq: update 'cpufreq_suspended' after stopping governors
Commit 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
introduced a bug where the governors wouldn't be stopped anymore for
->target{_index}() drivers during suspend. This happens because
'cpufreq_suspended' is updated before stopping the governors during suspend
and due to this __cpufreq_governor() would return early due to this check:
/* Don't start any governor operations if we are entering suspend */
if (cpufreq_suspended)
return 0;
Fixes: 8e30444e1530 ("cpufreq: fix cpufreq suspend/resume for intel_pstate") Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 8e30444e1530 "cpufreq: fix cpufreq suspend/resume for intel_pstate" Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Martin Lau <kafai@fb.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Medhurst [Tue, 30 Sep 2014 09:25:10 +0000 (10:25 +0100)]
ARM: 8179/1: kprobes-test: Fix compile error "bad immediate value for offset"
When compiling kprobes-test-arm.c the following error has been observed
/tmp/ccoT403o.s:21439: Error: bad immediate value for offset (4168)
This is caused by the compiler spilling it's literal pool too far away
from the site which is trying to reference it with a PC relative load.
This arises because the compiler is underestimating the size of the
inline assembler code present, which apparently it approximates as 4
bytes per line or instruction.
We fix this problem by moving the operations which generate more than
4 bytes out of the text section. Specifically, moving the .ascii
directives to the .rodata section.
Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 8178/1: fix set_tls for !CONFIG_KUSER_HELPERS
Joachim Eastwood reports that commit fbfb872f5f41 "ARM: 8148/1: flush
TLS and thumbee register state during exec" causes a boot-time crash
on a Cortex-M4 nommu system:
The problem is that set_tls is attempting to clear the TLS location in
the kernel-user helper page, which isn't set up on V7M.
Fix this by guarding the write to the kuser helper page with
a CONFIG_KUSER_HELPERS ifdef.
Fixes: fbfb872f5f41 ARM: 8148/1: flush TLS and thumbee register state during exec Reported-by: Joachim Eastwood <manabian@gmail.com> Tested-by: Joachim Eastwood <manabian@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 8177/1: cacheflush: Fix v7_exit_coherency_flush exynos build breakage on ARMv6
This fixes build breakage of platsmp.c if ARMv6 was chosen for compile
time options (e.g. by building allmodconfig):
$ make allmodconfig
$ make
CC arch/arm/mach-exynos/platsmp.o
/tmp/ccdQM0Eg.s: Assembler messages:
/tmp/ccdQM0Eg.s:432: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:437: Error: selected processor does not support ARM mode `isb '
/tmp/ccdQM0Eg.s:438: Error: selected processor does not support ARM mode `dsb '
make[1]: *** [arch/arm/mach-exynos/platsmp.o] Error 1
The error was introduced in commit "ARM: EXYNOS: Move code from
hotplug.c to platsmp.c". Previously code using
v7_exit_coherency_flush() macro was built with '-march=armv7-a' flag but
this flag dissapeared during the movement.
Fix this by annotating the v7_exit_coherency_flush() asm code with
armv7-a architecture.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reported-by: Mark Brown <broonie@kernel.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The correct type (SSM2602/SSM2603/SSM2604) is passed down
from the ssm2602_spi_probe()/ssm2602_spi_probe() functions,
so use that instead of hardcoding it to SSM2602 in
ssm2602_probe().
Fixes: c924dc68f737 ("ASoC: ssm2602: Split SPI and I2C code into different modules") Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Cc: stable@vger.kernel.org
KY Srinivasan [Mon, 29 Sep 2014 05:16:43 +0000 (22:16 -0700)]
hyperv: Fix a bug in netvsc_start_xmit()
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Tested-by: Long Li <longli@microsoft.com> Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Lu [Fri, 26 Sep 2014 02:30:08 +0000 (10:30 +0800)]
ACPI / i915: Update the condition to ignore firmware backlight change request
Some of the Thinkpads' firmware will issue a backlight change request
through i915 operation region unconditionally on AC plug/unplug, the
backlight level used is arbitrary and thus should be ignored. This is
handled by commit 0b9f7d93ca61 (ACPI / i915: ignore firmware requests
for backlight change). Then there is a Dell laptop whose vendor backlight
interface also makes use of operation region to change backlight level
and with the above commit, that interface no long works. The condition
used to ignore the backlight change request from firmware is thus
changed to: if the vendor backlight interface is not in use and the ACPI
backlight interface is broken, we ignore the requests; oterwise, we keep
processing them.
Fixes: 0b9f7d93ca61 (ACPI / i915: ignore firmware requests for backlight change) Link: https://lkml.org/lkml/2014/9/23/854 Reported-and-tested-by: Pali Rohár <pali.rohar@gmail.com> Cc: 3.16+ <stable@vger.kernel.org> # 3.16+ Signed-off-by: Aaron Lu <aaron.lu@intel.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de> Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 29 Sep 2014 17:34:29 +0000 (10:34 -0700)]
gro: fix aggregation for skb using frag_list
In commit 8a29111c7ca6 ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com> Fixes: 8a29111c7ca6 ("net: gro: allow to build full sized skb") Reported-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wilson [Thu, 25 Sep 2014 09:13:12 +0000 (10:13 +0100)]
drm/i915: Flush the PTEs after updating them before suspend
As we use WC updates of the PTE, we are responsible for notifying the
hardware when to flush its TLBs. Do so after we zap all the PTEs before
suspend (and the BIOS tries to read our GTT).
cpufreq: integrator: fix integrator_cpufreq_remove return type
When building this driver as a module, we get a helpful warning
about the return type:
drivers/cpufreq/integrator-cpufreq.c:232:2: warning: initialization from incompatible pointer type
.remove = __exit_p(integrator_cpufreq_remove),
If the remove callback returns void, the caller gets an undefined
value as it expects an integer to be returned. This fixes the
problem by passing down the value from cpufreq_unregister_driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: pcc-cpufreq: Fix wait_event() under spinlock
Fix the following bug introduced by commit 8fec051eea73 (cpufreq:
Convert existing drivers to use cpufreq_freq_transition_{begin|end})
that forgot to move the spin_lock() in pcc_cpufreq_target() past
cpufreq_freq_transition_begin() which calls wait_event():
Fixes: 8fec051eea73 (cpufreq: Convert existing drivers to use cpufreq_freq_transition_{begin|end}) Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com> Cc: 3.15+ <stable@vger.kernel.org> # 3.15+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
WANG Cong [Thu, 25 Sep 2014 00:07:53 +0000 (17:07 -0700)]
neigh: check error pointer instead of NULL for ipv4_neigh_lookup()
Fixes: commit f187bc6efb7250afee0e2009b6106 ("ipv4: No need to set generic neighbour pointer") Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Two small fixes for omap dmaengine driver which fixes cyclic suspend
and resume"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: omap-dma: Restore the CLINK_CTRL in resume path
dmaengine: omap-dma: Add memory barrier to dma_resume path
projects / mirror_ubuntu-kernels.git / log