Jiri Pirko [Sat, 5 Oct 2019 18:04:34 +0000 (20:04 +0200)]
net: genetlink: introduce dump info struct to be available during dumpit op
Currently the cb->data is taken by ops during non-parallel dumping.
Introduce a new structure genl_dumpit_info and store the ops there.
Distribute the info to both non-parallel and parallel dumping. Also add
a helper genl_dumpit_info() to easily get the info structure in the
dumpit callback from cb.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 5 Oct 2019 18:04:33 +0000 (20:04 +0200)]
net: genetlink: push doit/dumpit code from genl_family_rcv_msg
Currently the function genl_family_rcv_msg() is quite big. Since it is
quite convenient, push code that is related to doit and dumpit ops into
separate functions.
Do small changes on the way, like rc/err unification, NULL check etc.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yi-Hung Wei [Fri, 4 Oct 2019 16:26:44 +0000 (09:26 -0700)]
openvswitch: Allow attaching helper in later commit
This patch allows to attach conntrack helper to a confirmed conntrack
entry. Currently, we can only attach alg helper to a conntrack entry
when it is in the unconfirmed state. This patch enables an use case
that we can firstly commit a conntrack entry after it passed some
initial conditions. After that the processing pipeline will further
check a couple of packets to determine if the connection belongs to
a particular application, and attach alg helper to the connection
in a later stage.
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
create netdevsim instances in namespace
Allow user to create netdevsim devlink and netdevice instances in a
network namespace according to the namespace where the user resides in.
Add a selftest to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 5 Oct 2019 06:10:33 +0000 (08:10 +0200)]
selftests: test creating netdevsim inside network namespace
Add a test that creates netdevsim instance inside network namespace
and verifies that the related devlink instance and port netdevices
reside in the namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Sat, 5 Oct 2019 06:10:32 +0000 (08:10 +0200)]
netdevsim: create devlink and netdev instances in namespace
When user does create new netdevsim instance using sysfs bus file,
create the devlink instance and related netdev instance in the namespace
of the caller.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net/tls: add ctrl path tracing and statistics
This set adds trace events related to TLS offload and basic MIB stats
for TLS.
First patch contains the TLS offload related trace points. Those are
helpful in troubleshooting offload issues, especially around the
resync paths.
Second patch adds a tracepoint to the fastpath of device offload,
it's separated out in case there will be objections to adding
fast path tracepoints. Again, it's quite useful for debugging
offload issues.
Next four patches add MIB statistics. The statistics are implemented
as per-cpu per-netns counters. Since there are currently no fast path
statistics we could move to atomic variables. Per-CPU seem more common.
Most basic statistics are number of created and live sessions, broken
out to offloaded and non-offloaded. Users seem to like those a lot.
Next there is a statistic for decryption errors. These are primarily
useful for device offload debug, in normal deployments decryption
errors should not be common.
Last but not least a counter for device RX resync.
====================
Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 4 Oct 2019 23:19:26 +0000 (16:19 -0700)]
net/tls: add TlsDecryptError stat
Add a statistic for TLS record decryption errors.
Since devices are supposed to pass records as-is when they
encounter errors this statistic will count bad records in
both pure software and inline crypto configurations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 4 Oct 2019 23:19:25 +0000 (16:19 -0700)]
net/tls: add statistics for installed sessions
Add SNMP stats for number of sockets with successfully
installed sessions. Break them down to software and
hardware ones. Note that if hardware offload fails
stack uses software implementation, and counts the
session appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 4 Oct 2019 23:19:23 +0000 (16:19 -0700)]
net/tls: add device decrypted trace point
Add a tracepoint to the TLS offload's fast path. This tracepoint
can be used to track the decrypted and encrypted status of received
records. Records decrypted by the device should have decrypted set
to 1, records which have neither decrypted nor decrypted set are
partially decrypted, require re-encryption and therefore are most
expensive to deal with.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 5 Oct 2019 19:56:59 +0000 (12:56 -0700)]
Merge tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- remove unneeded ar-option and KBUILD_ARFLAGS
- remove long-deprecated SUBDIRS
- fix modpost to suppress false-positive warnings for UML builds
- fix namespace.pl to handle relative paths to ${objtree}, ${srctree}
- make setlocalversion work for /bin/sh
- make header archive reproducible
- fix some Makefiles and documents
* tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: make headers archive reproducible
kbuild: update compile-test header list for v5.4-rc2
kbuild: two minor updates for Documentation/kbuild/modules.rst
scripts/setlocalversion: clear local variable to make it work for sh
namespace: fix namespace.pl script to support relative paths
video/logo: do not generate unneeded logo C files
video/logo: remove unneeded *.o pattern from clean-files
integrity: remove pointless subdir-$(CONFIG_...)
integrity: remove unneeded, broken attempt to add -fshort-wchar
modpost: fix static EXPORT_SYMBOL warnings for UML build
kbuild: correct formatting of header in kbuild module docs
kbuild: remove SUBDIRS support
kbuild: remove ar-option and KBUILD_ARFLAGS
Linus Torvalds [Sat, 5 Oct 2019 19:53:27 +0000 (12:53 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve patches mostly small but obvious fixes or cosmetic but small
updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix Nport ID display value
scsi: qla2xxx: Fix N2N link up fail
scsi: qla2xxx: Fix N2N link reset
scsi: qla2xxx: Optimize NPIV tear down process
scsi: qla2xxx: Fix stale mem access on driver unload
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
scsi: qla2xxx: Silence fwdump template message
scsi: hisi_sas: Make three functions static
scsi: megaraid: disable device when probe failed after enabled device
scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
scsi: qedf: Remove always false 'tmp_prio < 0' statement
scsi: ufs: skip shutdown if hba is not powered
scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF
Linus Torvalds [Sat, 5 Oct 2019 19:03:27 +0000 (12:03 -0700)]
Merge branch 'readdir' (readdir speedup and sanity checking)
This makes getdents() and getdents64() do sanity checking on the
pathname that it gives to user space. And to mitigate the performance
impact of that, it first cleans up the way it does the user copying, so
that the code avoids doing the SMAP/PAN updates between each part of the
dirent structure write.
I really wanted to do this during the merge window, but didn't have
time. The conversion of filldir to unsafe_put_user() is something I've
had around for years now in a private branch, but the extra pathname
checking finally made me clean it up to the point where it is mergable.
It's worth noting that the filename validity checking really should be a
bit smarter: it would be much better to delay the error reporting until
the end of the readdir, so that non-corrupted filenames are still
returned. But that involves bigger changes, so let's see if anybody
actually hits the corrupt directory entry case before worrying about it
further.
* branch 'readdir':
Make filldir[64]() verify the directory entry filename is valid
Convert filldir[64]() from __put_user() to unsafe_put_user()
Linus Torvalds [Sat, 5 Oct 2019 18:32:52 +0000 (11:32 -0700)]
Make filldir[64]() verify the directory entry filename is valid
This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().
This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.
There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.
There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption. It's really more
"protect user space from bad behavior" as pointed out by Jann. But
since Eric Biederman looked up the POSIX wording, here it is for context:
"From readdir:
The readdir() function shall return a pointer to a structure
representing the directory entry at the current position in the
directory stream specified by the argument dirp, and position the
directory stream at the next entry. It shall return a null pointer
upon reaching the end of the directory stream. The structure dirent
defined in the <dirent.h> header describes a directory entry.
From definitions:
3.129 Directory Entry (or Link)
An object that associates a filename with a file. Several directory
entries can associate names with the same file.
...
3.169 Filename
A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
characters composing the name may be selected from the set of all
character values excluding the slash character and the null byte. The
filenames dot and dot-dot have special meaning. A filename is
sometimes referred to as a 'pathname component'."
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.
We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')
See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.
Linus Torvalds [Sun, 22 May 2016 04:59:07 +0000 (21:59 -0700)]
Convert filldir[64]() from __put_user() to unsafe_put_user()
We really should avoid the "__{get,put}_user()" functions entirely,
because they can easily be mis-used and the original intent of being
used for simple direct user accesses no longer holds in a post-SMAP/PAN
world.
Manually optimizing away the user access range check makes no sense any
more, when the range check is generally much cheaper than the "enable
user accesses" code that the __{get,put}_user() functions still need.
So instead of __put_user(), use the unsafe_put_user() interface with
user_access_{begin,end}() that really does generate better code these
days, and which is generally a nicer interface. Under some loads, the
multiple user writes that filldir() does are actually quite noticeable.
This also makes the dirent name copy use unsafe_put_user() with a couple
of macros. We do not want to make function calls with SMAP/PAN
disabled, and the code this generates is quite good when the
architecture uses "asm goto" for unsafe_put_user() like x86 does.
Note that this doesn't bother with the legacy cases. Nobody should use
them anyway, so performance doesn't really matter there.
1) Fix ieeeu02154 atusb driver use-after-free, from Johan Hovold.
2) Need to validate TCA_CBQ_WRROPT netlink attributes, from Eric
Dumazet.
3) txq null deref in mac80211, from Miaoqing Pan.
4) ionic driver needs to select NET_DEVLINK, from Arnd Bergmann.
5) Need to disable bh during nft_connlimit GC, from Pablo Neira Ayuso.
6) Avoid division by zero in taprio scheduler, from Vladimir Oltean.
7) Various xgmac fixes in stmmac driver from Jose Abreu.
8) Avoid 64-bit division in mlx5 leading to link errors on 32-bit from
Michal Kubecek.
9) Fix bad VLAN check in rtl8366 DSA driver, from Linus Walleij.
10) Fix sleep while atomic in sja1105, from Vladimir Oltean.
11) Suspend/resume deadlock in stmmac, from Thierry Reding.
12) Various UDP GSO fixes from Josh Hunt.
13) Fix slab out of bounds access in tcp_zerocopy_receive(), from Eric
Dumazet.
14) Fix OOPS in __ipv6_ifa_notify(), from David Ahern.
15) Memory leak in NFC's llcp_sock_bind, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
selftests/net: add nettest to .gitignore
net: qlogic: Fix memory leak in ql_alloc_large_buffers
nfc: fix memory leak in llcp_sock_bind()
sch_dsmark: fix potential NULL deref in dsmark_init()
net: phy: at803x: use operating parameters from PHY-specific status
net: phy: extract pause mode
net: phy: extract link partner advertisement reading
net: phy: fix write to mii-ctrl1000 register
ipv6: Handle missing host route in __ipv6_ifa_notify
net: phy: allow for reset line to be tied to a sleepy GPIO controller
net: ipv4: avoid mixed n_redirects and rate_tokens usage
r8152: Set macpassthru in reset_resume callback
cxgb4:Fix out-of-bounds MSI-X info array access
Revert "ipv6: Handle race in addrconf_dad_work"
net: make sock_prot_memory_pressure() return "const char *"
rxrpc: Fix rxrpc_recvmsg tracepoint
qmi_wwan: add support for Cinterion CLS8 devices
tcp: fix slab-out-of-bounds in tcp_zerocopy_receive()
lib: textsearch: fix escapes in example code
udp: only do GSO if # of segs > 1
...
Linus Torvalds [Sat, 5 Oct 2019 15:44:02 +0000 (08:44 -0700)]
Merge tag 's390-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- defconfig updates
- Fix build errors with CC_OPTIMIZE_FOR_SIZE due to usage of "i"
constraint for function arguments. Two kvm changes acked-by Christian
Borntraeger.
- Fix -Wunused-but-set-variable warnings in mm code.
- Avoid a constant misuse in qdio.
- Handle a case when cpumf is temporarily unavailable.
* tag 's390-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
KVM: s390: mark __insn32_query() as __always_inline
KVM: s390: fix __insn32_query() inline assembly
s390: update defconfigs
s390/pci: mark function(s) __always_inline
s390/mm: mark function(s) __always_inline
s390/jump_label: mark function(s) __always_inline
s390/cpu_mf: mark function(s) __always_inline
s390/atomic,bitops: mark function(s) __always_inline
s390/mm: fix -Wunused-but-set-variable warnings
s390: mark __cpacf_query() as __always_inline
s390/qdio: clarify size of the QIB parm area
s390/cpumf: Fix indentation in sampling device driver
s390/cpumsf: Check for CPU Measurement sampling
s390/cpumf: Use consistant debug print format
Heiko Carstens [Wed, 2 Oct 2019 12:34:37 +0000 (14:34 +0200)]
KVM: s390: mark __insn32_query() as __always_inline
__insn32_query() will not compile if the compiler decides to not
inline it, since it contains an inline assembly with an "i" constraint
with variable contents.
Heiko Carstens [Wed, 2 Oct 2019 12:24:47 +0000 (14:24 +0200)]
KVM: s390: fix __insn32_query() inline assembly
The inline assembly constraints of __insn32_query() tell the compiler
that only the first byte of "query" is being written to. Intended was
probably that 32 bytes are written to.
Fix and simplify the code and just use a "memory" clobber.
Fixes: d668139718a9 ("KVM: s390: provide query function for instructions returning 32 byte") Cc: stable@vger.kernel.org # v5.2+ Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Dmitry Goldin [Fri, 4 Oct 2019 10:40:07 +0000 (10:40 +0000)]
kheaders: make headers archive reproducible
In commit 43d8ce9d65a5 ("Provide in-kernel headers to make
extending kernel easier") a new mechanism was introduced, for kernels
>=5.2, which embeds the kernel headers in the kernel image or a module
and exposes them in procfs for use by userland tools.
The archive containing the header files has nondeterminism caused by
header files metadata. This patch normalizes the metadata and utilizes
KBUILD_BUILD_TIMESTAMP if provided and otherwise falls back to the
default behaviour.
In commit f7b101d33046 ("kheaders: Move from proc to sysfs") it was
modified to use sysfs and the script for generation of the archive was
renamed to what is being patched.
Masahiro Yamada [Thu, 3 Oct 2019 02:36:29 +0000 (11:36 +0900)]
kbuild: update compile-test header list for v5.4-rc2
Commit 6dc280ebeed2 ("coda: remove uapi/linux/coda_psdev.h") removed
a header in question. Some more build errors were fixed. Add more
headers into the test coverage.
Masahiro Yamada [Tue, 1 Oct 2019 12:17:24 +0000 (21:17 +0900)]
scripts/setlocalversion: clear local variable to make it work for sh
Geert Uytterhoeven reports a strange side-effect of commit 858805b336be
("kbuild: add $(BASH) to run scripts with bash-extension"), which
inserts the contents of a localversion file in the build directory twice.
[Steps to Reproduce]
$ echo bar > localversion
$ mkdir build
$ cd build/
$ echo foo > localversion
$ make -s -f ../Makefile defconfig include/config/kernel.release
$ cat include/config/kernel.release
5.4.0-rc1foofoobar
This comes down to the behavior change of local variables.
The 'man sh' on my Ubuntu machine, where sh is an alias to dash,
explains as follows:
When a variable is made local, it inherits the initial value and
exported and readonly flags from the variable with the same name
in the surrounding scope, if there is one. Otherwise, the variable
is initially unset.
[Test Code]
foo ()
{
local res
echo "res: $res"
}
res=1
foo
[Result]
$ sh test.sh
res: 1
$ bash test.sh
res:
So, scripts/setlocalversion correctly works only for bash in spite of
its hashbang being #!/bin/sh. Nobody had noticed it before because
CONFIG_SHELL was previously set to bash almost all the time.
Now that CONFIG_SHELL is set to sh, we must write portable and correct
code. I gave the Fixes tag to the commit that uncovered the issue.
Clear the variable 'res' in collect_files() to make it work for sh
(and it also works on distributions where sh is an alias to bash).
Fixes: 858805b336be ("kbuild: add $(BASH) to run scripts with bash-extension") Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Jacob Keller [Fri, 27 Sep 2019 23:30:27 +0000 (16:30 -0700)]
namespace: fix namespace.pl script to support relative paths
The namespace.pl script does not work properly if objtree is not set to
an absolute path. The do_nm function is run from within the find
function, which changes directories.
Because of this, appending objtree, $File::Find::dir, and $source, will
return a path which is not valid from the current directory.
This used to work when objtree was set to an absolute path when using
"make namespacecheck". It appears to have not worked when calling
./scripts/namespace.pl directly.
This behavior was changed in 7e1c04779efd ("kbuild: Use relative path
for $(objtree)", 2014-05-14)
Rather than fixing the Makefile to set objtree to an absolute path, just
fix namespace.pl to work when srctree and objtree are relative. Also fix
the script to use an absolute path for these by default.
Use the File::Spec module for this purpose. It's been part of perl
5 since 5.005.
The curdir() function is used to get the current directory when the
objtree and srctree aren't set in the environment.
rel2abs() is used to convert possibly relative objtree and srctree
environment variables to absolute paths.
Finally, the catfile() function is used instead of string appending
paths together, since this is more robust when joining paths together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 21 Aug 2019 04:12:35 +0000 (13:12 +0900)]
video/logo: do not generate unneeded logo C files
Currently, all the logo C files are generated irrespective of the
CONFIG options. Adding them to extra-y is wrong. What we need to do
here is to add them to 'targets' so that if_changed works properly.
Files listed in 'targets' are cleaned, so clean-files is unneeded.
integrity: remove unneeded, broken attempt to add -fshort-wchar
I guess commit 15ea0e1e3e18 ("efi: Import certificates from UEFI Secure
Boot") attempted to add -fshort-wchar for building load_uefi.o, but it
has never worked as intended.
load_uefi.o is created in the platform_certs/ sub-directory. If you
really want to add -fshort-wchar, the correct code is:
Jakub Kicinski [Sat, 5 Oct 2019 00:36:50 +0000 (17:36 -0700)]
selftests/net: add nettest to .gitignore
nettest is missing from gitignore.
Fixes: acda655fefae ("selftests: Add nettest") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Navid Emamdoost [Fri, 4 Oct 2019 20:24:39 +0000 (15:24 -0500)]
net: qlogic: Fix memory leak in ql_alloc_large_buffers
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Fix regression with AR8035 speed downgrade
The following series attempts to address an issue spotted by tinywrkb
with the AR8035 on the Cubox-i2 in a situation where the PHY downgrades
the negotiated link.
This is version 2, not much has changed other than rebasing on the
current net tree. Changes have happend to patch 2 due to conflicts,
so I dropped Andrew's reviewed-by. Minor context changes to patch 4
which I don't consider important enough to warrant dropping the
reviewed-by.
Before commit 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in
genphy_read_status"), we would read not only the link partner's
advertisement, but also our own advertisement from the PHY registers,
and use both to derive the PHYs current link mode. This works when the
AR8035 downgrades the speed, because it appears that the AR8035 clears
link mode bits in the advertisement registers as part of the downgrade.
Commentary: what is not yet known is whether the AR8035 restores the
advertisement register when the link goes down to the
previous state.
However, since the above referenced commit, we no longer use the PHYs
advertisement registers, instead converting the link partner's
advertisement to the ethtool link mode array, and combine that with
phylib's cached version of our advertisement - which is not updated on
speed downgrade.
This results in phylib disagreeing with the actual operating mode of
the PHY.
Commentary: I wonder how many more PHY drivers are broken by this
commit, but have yet to be discovered.
The obvious way to address this would be to disable the downgrade
feature, and indeed this does fix the problem in tinywrkb's case - his
link partner instead downgrades the speed by reducing its
advertisement, resulting in phylib correctly evaluating a slower speed.
However, it has a serious drawback - the gigabit control register (MII
register 9) appears to become read only. It seems the only way to
update the register is to re-enable the downgrade feature, reset the
PHY, changing register 9, disable the downgrade feature, and reset the
PHY again.
This series attempts to address the problem using a different approach,
similar to the approach taken with Marvell PHYs. The AR8031, AR8033
and AR8035 have a PHY-Specific Status register which reports the
actual operating mode of the PHY - both speed and duplex. This
register correctly reports the operating mode irrespective of whether
autoneg is enabled or not. We use this register to fill in phylib's
speed and duplex parameters.
In detail:
Patch 1 fixes a bug where writing to register 9 does not update
phylib's advertisement mask in the same way that writing register 4
does; this looks like an omission from when gigabit PHY support came
into being.
Patch 2 seperates the generic phylib code which reads the link partners
advertisement from the PHY, so that we can re-use this in the Atheros
PHY driver.
Patch 3 seperates the generic phylib pause mode; phylib provides no
help for MAC drivers to ascertain the negotiated pause mode, it merely
copies the link partner's pause mode bits into its own variables.
Commentary: Both the aforementioned Atheros PHYs and Marvell PHYs
provide the resolved pause modes in terms of whether
we should transmit pause frames, or whether we should
allow reception of pause frames. Surely the resolution
of this should be in phylib?
Patch 4 provides the Atheros PHY driver with a private "read_status"
implementation that fills in phylib's speed and duplex settings
depending on the PHY-Specific status register. This ensures that
phylib and the MAC driver match the operating mode that the PHY has
decided to use. Since the register also gives us MDIX status, we
can trivially fill that status in as well.
Note that, although the bits mentioned in this patch for this register
match those in th Marvell PHY driver, and it is located at the same
address, the meaning of other register bits varies between the PHYs.
Therefore, I do not feel that it would be appropriate to make this some
kind of generic function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 4 Oct 2019 16:06:14 +0000 (17:06 +0100)]
net: phy: at803x: use operating parameters from PHY-specific status
Read the PHY-specific status register for the current operating mode
(speed and duplex) of the PHY. This register reflects the actual
mode that the PHY has resolved depending on either the advertisements
of autoneg is enabled, or the forced mode if autoneg is disabled.
This ensures that phylib's software state always tracks the hardware
state.
It seems both AR8033 (which uses the AR8031 ID) and AR8035 support
this status register. AR8030 is not known at the present time.
This patch depends on "net: phy: extract pause mode" and "net: phy:
extract link partner advertisement reading".
Reported-by: tinywrkb <tinywrkb@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: tinywrkb <tinywrkb@gmail.com> Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 4 Oct 2019 16:06:09 +0000 (17:06 +0100)]
net: phy: extract pause mode
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.
Tested-by: tinywrkb <tinywrkb@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 4 Oct 2019 16:06:04 +0000 (17:06 +0100)]
net: phy: extract link partner advertisement reading
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Tested-by: tinywrkb <tinywrkb@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Fri, 4 Oct 2019 16:05:58 +0000 (17:05 +0100)]
net: phy: fix write to mii-ctrl1000 register
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in __ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.
Since the DAD sequence can not be aborted, add a check for the missing
host route in __ipv6_ifa_notify. The only way this should happen is due
to the previously mentioned race. The host route is created when the
address is added to an interface; it is only removed on a down event
where the address is kept. Add a warning if the host route is missing
AND the device is up; this is a situation that should never happen.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional") Reported-by: Rajendra Dendukuri <rajendra.dendukuri@broadcom.com> Signed-off-by: David Ahern <dsahern@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Merello [Fri, 4 Oct 2019 13:53:32 +0000 (15:53 +0200)]
net: phy: allow for reset line to be tied to a sleepy GPIO controller
mdio_device_reset() makes use of the atomic-pretending API flavor for
handling the PHY reset GPIO line.
I found no hint that mdio_device_reset() is called from atomic context
and indeed it uses usleep_range() since long time, so I would assume that
it is OK to sleep there.
This patch switch to gpiod_set_value_cansleep() in mdio_device_reset().
This is relevant if e.g. the PHY reset line is tied to a I2C GPIO
controller.
This has been tested on a ZynqMP board running an upstream 4.19 kernel and
then hand-ported on current kernel tree.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 4 Oct 2019 13:11:17 +0000 (15:11 +0200)]
net: ipv4: avoid mixed n_redirects and rate_tokens usage
Since commit c09551c6ff7f ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.
If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.
Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().
Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.
The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.
Reported-by: Xiumei Mu <xmu@redhat.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kai-Heng Feng [Fri, 4 Oct 2019 12:51:04 +0000 (20:51 +0800)]
r8152: Set macpassthru in reset_resume callback
r8152 may fail to establish network connection after resume from system
suspend.
If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.
So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 4 Oct 2019 09:50:12 +0000 (11:50 +0200)]
net: devlink: don't ignore errors during dumpit
Currently, some dumpit function may end-up with error which is not
-EMSGSIZE and this error is silently ignored. Use does not have clue
that something wrong happened. Instead of silent ignore, propagate
the error to user.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 4 Oct 2019 00:33:47 +0000 (03:33 +0300)]
net: dsa: sja1105: Add support for port mirroring
Amazingly, of all features, this does not require a switch reset.
Tested with:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress matchall skip_sw \
action mirred egress mirror dev swp3
tc filter show dev swp2 ingress
tc filter del dev swp2 ingress pref 49152
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Thu, 3 Oct 2019 22:36:15 +0000 (04:06 +0530)]
cxgb4:Fix out-of-bounds MSI-X info array access
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD") Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric reported tests failings with commit. After digging into it,
the bottom line is that the DAD sequence is not to be messed with.
There are too many cases that are expected to proceed regardless
of whether a device is up.
Revert the patch and I will send a different solution for the
problem Rajendra reported.
Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Thu, 3 Oct 2019 20:29:24 +0000 (23:29 +0300)]
net, uapi: fix -Wpointer-arith warnings
Add casts to fix these warnings:
./usr/include/linux/netfilter_arp/arp_tables.h:200:19: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/netfilter_bridge/ebtables.h:197:19: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/netfilter_ipv4/ip_tables.h:223:19: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/netfilter_ipv6/ip6_tables.h:263:19: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/tipc_config.h:310:28: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/tipc_config.h:410:24: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
./usr/include/linux/virtio_ring.h:170:16: error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]
Those are theoretical probably but kernel doesn't control compiler flags
in userspace.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series fixes the BCM54210E RGMII delay configuration which
could only have worked in a PHY_INTERFACE_MODE_RGMII configuration.
There is a forward declaration added such that the first patch can be
picked up for -stable and apply fine all the way back to when the bug
was introduced.
The second patch eliminates duplicated code that used a different kind
of logic and did not use existing constants defined.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: broadcom: Fix RGMII delays configuration for BCM54210E
Commit 0fc9ae107669 ("net: phy: broadcom: add support for
BCM54210E") added support for BCM54210E but also unconditionally cleared
the RXC to RXD skew and the TXD to TXC skew, thus only making
PHY_INTERFACE_MODE_RGMII a possible configuration. Use
bcm54xx_config_clock_delay() which correctly sets the registers
depending on the 4 possible PHY interface values that exist for RGMII.
Fixes: 0fc9ae107669 ("net: phy: broadcom: add support for BCM54210E") Reported-by: Manasa Mudireddy <manasa.mudireddy@broadcom.com> Reported-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net/tls: separate the TLS TOE code out
We have 3 modes of operation of TLS - software, crypto offload
(Mellanox, Netronome) and TCP Offload Engine-based (Chelsio).
The last one takes over the socket, like any TOE would, and
is not really compatible with how we want to do things in the
networking stack.
Confusingly the name of the crypto-only offload mode is TLS_HW,
while TOE-offload related functions use tls_hw_ as their prefix.
Engineers looking to implement offload are also be faced with
TOE artefacts like struct tls_device (while, again,
CONFIG_TLS_DEVICE actually gates the non-TOE offload).
To improve the clarity of the offload code move the TOE code
into new files, and rename the functions and structures
appropriately.
Because TOE-offload takes over the socket, and makes no use of
the TLS infrastructure in the kernel, the rest of the code
(anything beyond the ULP setup handlers) do not have to worry
about the mode == TLS_HW_RECORD case.
The increase in code size is due to duplication of the full
license boilerplate. Unfortunately original author (Dave Watson)
seems unreachable :(
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:59 +0000 (11:18 -0700)]
net/tls: allow compiling TLS TOE out
TLS "record layer offload" requires TOE, and bypasses most of
the normal networking stack. It is also significantly less
maintained. Allow users to compile it out to avoid issues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:58 +0000 (11:18 -0700)]
net/tls: rename tls_hw_* functions tls_toe_*
The tls_hw_* functions are quite confusingly named, since they
are related to the TOE-offload, not TLS_HW offload which doesn't
require TOE. Rename them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:57 +0000 (11:18 -0700)]
net/tls: move TOE-related code to a separate file
Move tls_hw_* functions to a new, separate source file
to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:56 +0000 (11:18 -0700)]
net/tls: move tls_build_proto() on init path
Move tls_build_proto() so that TOE offload doesn't have to call it
mid way through its bypass enable path.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:55 +0000 (11:18 -0700)]
net/tls: rename tls_device to tls_toe_device
Rename struct tls_device to struct tls_toe_device to avoid
confusion with normal, non-TOE offload.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 3 Oct 2019 18:18:54 +0000 (11:18 -0700)]
net/tls: move TOE-related structures to a separate header
Move tls_device structure and register/unregister functions
to a new header to avoid confusion with normal, non-TOE offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 3 Oct 2019 16:44:44 +0000 (17:44 +0100)]
rxrpc: Fix rxrpc_recvmsg tracepoint
Fix the rxrpc_recvmsg tracepoint to handle being called with a NULL call
parameter.
Fixes: a25e21f0bcd2 ("rxrpc, afs: Use debug_ids rather than pointers in traces") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 4 Oct 2019 20:02:47 +0000 (13:02 -0700)]
Merge tag 'riscv/for-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- Ensure that exclusive-load reservations are terminated after system
call or exception handling. This primarily affects QEMU, which does
not expire load reservations.
- Fix an issue primarily affecting RV32 platforms that can cause the DT
header to be corrupted, causing boot failures.
* tag 'riscv/for-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix memblock reservation for device tree blob
RISC-V: Clear load reservations while restoring hart contexts
Paul Burton [Fri, 4 Oct 2019 17:41:02 +0000 (17:41 +0000)]
MIPS: fw/arc: Remove unused addr variable
The addr variable in prom_free_prom_memory() has been unused since
commit 0df1007677d5 ("MIPS: fw: Record prom memory"), leading to a
compiler warning:
Linus Torvalds [Fri, 4 Oct 2019 18:17:51 +0000 (11:17 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM and x86 bugfixes of all kinds.
The most visible one is that migrating a nested hypervisor has always
been busted on Broadwell and newer processors, and that has finally
been fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
KVM: x86: omit "impossible" pmu MSRs from MSR list
KVM: nVMX: Fix consistency check on injected exception error code
KVM: x86: omit absent pmu MSRs from MSR list
selftests: kvm: Fix libkvm build error
kvm: vmx: Limit guest PMCs to those supported on the host
kvm: x86, powerpc: do not allow clearing largepages debugfs entry
KVM: selftests: x86: clarify what is reported on KVM_GET_MSRS failure
KVM: VMX: Set VMENTER_L1D_FLUSH_NOT_REQUIRED if !X86_BUG_L1TF
selftests: kvm: add test for dirty logging inside nested guests
KVM: x86: fix nested guest live migration with PML
KVM: x86: assign two bits to track SPTE kinds
KVM: x86: Expose XSAVEERPTR to the guest
kvm: x86: Enumerate support for CLZERO instruction
kvm: x86: Use AMD CPUID semantics for AMD vCPUs
kvm: x86: Improve emulation of CPUID leaves 0BH and 1FH
KVM: X86: Fix userspace set invalid CR4
kvm: x86: Fix a spurious -E2BIG in __do_cpuid_func
KVM: LAPIC: Loosen filter for adaptive tuning of lapic_timer_advance_ns
KVM: arm/arm64: vgic: Use the appropriate TRACE_INCLUDE_PATH
arm64: KVM: Kill hyp_alternate_select()
...
Linus Torvalds [Fri, 4 Oct 2019 18:13:09 +0000 (11:13 -0700)]
Merge tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- a fix in the Xen balloon driver avoiding hitting a BUG_ON() in some
cases, plus a follow-on cleanup series for that driver
- a patch for introducing non-blocking EFI callbacks in Xen's EFI
driver, plu a cleanup patch for Xen EFI handling merging the x86 and
ARM arch specific initialization into the Xen EFI driver
- a fix of the Xen xenbus driver avoiding a self-deadlock when cleaning
up after a user process has died
- a fix for Xen on ARM after removal of ZONE_DMA
- a cleanup patch for avoiding build warnings for Xen on ARM
* tag 'for-linus-5.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: fix self-deadlock after killing user process
xen/efi: have a common runtime setup function
arm: xen: mm: use __GPF_DMA32 for arm64
xen/balloon: Clear PG_offline in balloon_retrieve()
xen/balloon: Mark pages PG_offline in balloon_append()
xen/balloon: Drop __balloon_append()
xen/balloon: Set pages PageOffline() in balloon_add_region()
ARM: xen: unexport HYPERVISOR_platform_op function
xen/efi: Set nonblocking callbacks
====================
devlink: allow devlink instances to change network namespace
Devlink from the beginning counts with network namespaces, but the
instances has been fixed to init_net.
Implement change of network namespace as part of "devlink reload"
procedure like this:
$ ip netns add testns1
$ devlink/devlink dev reload netdevsim/netdevsim10 netns testns1
This command reloads device "netdevsim10" into network
namespace "testns1".
Note that "devlink reload" reinstantiates driver objects, effectively it
reloads the driver instance, including possible hw reset etc. Newly
created netdevices respect the network namespace of the parent devlink
instance and according to that, they are created in target network
namespace.
Driver is able to refuse to be reloaded into different namespace. That
is the case of mlx4 right now.
FIB entries and rules are replayed during FIB notifier registration
which is triggered during reload (driver instance init). FIB notifier
is also registered to the target network namespace, that allows user
to use netdevsim devlink resources to setup per-namespace limits of FIB
entries and FIB rules. In fact, with multiple netdevsim instances
in each network namespace, user might setup different limits.
This maintains and extends current netdevsim resources behaviour.
Patch 1 prepares netdevsim code for the follow-up changes in the
patchset. It does not change the behaviour, only moves pet-init_netns
accounting to netdevsim instance, which is also in init_netns.
Patches 2-5 prepare the FIB notifier making it per-netns and to behave
correctly upon error conditions.
Patch 6 just exports a devlink_net helper so it can be used in drivers.
Patches 7-9 do preparations in mlxsw driver.
Patches 10-13 do preparations in netdevsim driver, namely patch 12
implements proper devlink reload where the driver instance objects are
actually re-created as they should be.
Patch 14 actually implements the possibility to reload into a different
network namespace.
Patch 15 adds needed selftests for devlink reload into namespace for
netdevsim driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:39 +0000 (11:49 +0200)]
net: devlink: allow to change namespaces during reload
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:38 +0000 (11:49 +0200)]
netdevsim: take devlink net instead of init_net
Follow-up patch is going to allow to reload devlink instance into
different network namespace, so use devlink_net() helper instead
of init_net.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:37 +0000 (11:49 +0200)]
netdevsim: register port netdevices into net of device
Register newly created port netdevice into net namespace
that the parent device belongs to.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:36 +0000 (11:49 +0200)]
netdevsim: implement proper devlink reload
During devlink reload, all driver objects should be reinstantiated with
the exception of devlink instance and devlink resources and params.
Move existing devlink_resource_size_get() calls into fib_create() just
before fib notifier is registered. Also, make sure that extack is
propagated down to fib_notifier_register() call.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:35 +0000 (11:49 +0200)]
netdevsim: add all ports in nsim_dev_create() and del them in destroy()
Currently the probe/remove function does this separately. Put the
addition an deletion of ports into nsim_dev_create() and
nsim_dev_destroy().
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:29 +0000 (11:49 +0200)]
mlxsw: spectrum_router: Don't rely on missing extack to symbolize dump
Currently if info->extack is NULL, mlxsw assumes that the event came
down from dump. Originally, the dump did not propagate the return value
back to the original caller (fib_notifier_register()). However, that is
now happening. So benefit from this and push the error up if it happened.
Remove rule cases in work handlers that are now dead code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:28 +0000 (11:49 +0200)]
net: fib_notifier: propagate possible error during fib notifier registration
Unlike events for registered notifier, during the registration, the
errors that happened for the block being registered are not propagated
up to the caller. Make sure the error is propagated for FIB rules and
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:27 +0000 (11:49 +0200)]
net: fib_notifier: make FIB notifier per-netns
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 3 Oct 2019 09:49:26 +0000 (11:49 +0200)]
netdevsim: change fib accounting and limitations to be per-device
Currently, the accounting is done per-namespace. However, devlink
instance is always in init_net namespace for now, so only the accounting
related to init_net is used. Limitations set using devlink resources
are only considered for init_net. nsim_devlink_net() always
returns init_net always.
Make the accounting per-device. This brings no functional change.
Per-device accounting has the same values as per-net.
For a single netdevsim instance, the behaviour is exactly the same
as before. When multiple netdevsim instances are created, each
can have different limits.
This is in prepare to implement proper devlink netns support. After
that, the devlink instance which would exist in particular netns would
account and limit that netns.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 4 Oct 2019 17:36:31 +0000 (10:36 -0700)]
Merge tag 'copy-struct-from-user-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull copy_struct_from_user() helper from Christian Brauner:
"This contains the copy_struct_from_user() helper which got split out
from the openat2() patchset. It is a generic interface designed to
copy a struct from userspace.
The helper will be especially useful for structs versioned by size of
which we have quite a few. This allows for backwards compatibility,
i.e. an extended struct can be passed to an older kernel, or a legacy
struct can be passed to a newer kernel. For the first case (extended
struct, older kernel) the new fields in an extended struct can be set
to zero and the struct safely passed to an older kernel.
The most obvious benefit is that this helper lets us get rid of
duplicate code present in at least sched_setattr(), perf_event_open(),
and clone3(). More importantly it will also help to ensure that users
implementing versioning-by-size end up with the same core semantics.
This point is especially crucial since we have at least one case where
versioning-by-size is used but with slighly different semantics:
sched_setattr(), perf_event_open(), and clone3() all do do similar
checks to copy_struct_from_user() while rt_sigprocmask(2) always
rejects differently-sized struct arguments.
With this pull request we also switch over sched_setattr(),
perf_event_open(), and clone3() to use the new helper"
* tag 'copy-struct-from-user-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
usercopy: Add parentheses around assignment in test_copy_struct_from_user
perf_event_open: switch to copy_struct_from_user()
sched_setattr: switch to copy_struct_from_user()
clone3: switch to copy_struct_from_user()
lib: introduce copy_struct_from_user() helper
Linus Torvalds [Fri, 4 Oct 2019 17:18:56 +0000 (10:18 -0700)]
Merge tag 'for-linus-20191003' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull clone3/pidfd fixes from Christian Brauner:
"This contains a couple of fixes:
- Fix pidfd selftest compilation (Shuah Kahn)
Due to a false linking instruction in the Makefile compilation for
the pidfd selftests would fail on some systems.
- Fix compilation for glibc on RISC-V systems (Seth Forshee)
In some scenarios linux/uapi/linux/sched.h is included where
__ASSEMBLY__ is defined causing a build failure because struct
clone_args was not guarded by an #ifndef __ASSEMBLY__.
- Add missing clone3() and struct clone_args kernel-doc (Christian Brauner)
clone3() and struct clone_args were missing kernel-docs. (The goal
is to use kernel-doc for any function or type where it's worth it.)
For struct clone_args this also contains a comment about the fact
that it's versioned by size"
* tag 'for-linus-20191003' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
sched: add kernel-doc for struct clone_args
fork: add kernel-doc for clone3
selftests: pidfd: Fix undefined reference to pthread_create()
sched: Add __ASSEMBLY__ guards around struct clone_args
Linus Torvalds [Fri, 4 Oct 2019 17:12:37 +0000 (10:12 -0700)]
Merge tag 'drm-fixes-2019-10-04' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Been offline for 3 days, got back and had some fixes queued up.
Nothing too major, the i915 dp-mst fix is important, and amdgpu has a
bulk move speedup fix and some regressions, but nothing too insane for
an rc2 pull. The intel fixes are also 2 weeks worth, they missed the
boat last week.
core:
- writeback fixes
i915:
- Fix DP-MST crtc_mask
- Fix dsc dpp calculations
- Fix g4x sprite scaling stride check with GTT remapping
- Fix concurrence on cases where requests where getting retired at
same time as resubmitted to HW
- Fix gen9 display resolutions by setting the right max plane width
- Fix GPU hang on preemption
- Mark contents as dirty on a write fault. This was breaking cursor
sprite with dumb buffers.
komeda:
- memory leak fix
tilcdc:
- include fix
amdgpu:
- Enable bulk moves
- Power metrics fixes for Navi
- Fix S4 regression
- Add query for tcc disabled mask
- Fix several leaks in error paths
- randconfig fixes
- clang fixes"
* tag 'drm-fixes-2019-10-04' of git://anongit.freedesktop.org/drm/drm: (21 commits)
Revert "drm/i915: Fix DP-MST crtc_mask"
drm/omap: fix max fclk divider for omap36xx
drm/i915: Fix g4x sprite scaling stride check with GTT remapping
drm/i915/dp: Fix dsc bpp calculations, v5.
drm/amd/display: fix dcn21 Makefile for clang
drm/amd/display: hide an unused variable
drm/amdgpu: display_mode_vba_21: remove uint typedef
drm/amdgpu: hide another #warning
drm/amdgpu: make pmu support optional, again
drm/amd/display: memory leak
drm/amdgpu: fix multiple memory leaks in acp_hw_init
drm/amdgpu: return tcc_disabled_mask to userspace
drm/amdgpu: don't increment vram lost if we are in hibernation
Revert "drm/amdgpu: disable stutter mode for renoir"
drm/amd/powerplay: add sensor lock support for smu
drm/amd/powerplay: change metrics update period from 1ms to 100ms
drm/amdgpu: revert "disable bulk moves for now"
drm/tilcdc: include linux/pinctrl/consumer.h again
drm/komeda: prevent memory leak in komeda_wb_connector_add
drm: Clear the fence pointer when writeback job signaled
...
Linus Torvalds [Fri, 4 Oct 2019 16:56:51 +0000 (09:56 -0700)]
Merge tag 'for-linus-2019-10-03' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Mandate timespec64 for the io_uring timeout ABI (Arnd)
- Set of NVMe changes via Sagi:
- controller removal race fix from Balbir
- quirk additions from Gabriel and Jian-Hong
- nvme-pci power state save fix from Mario
- Add 64bit user commands (for 64bit registers) from Marta
- nvme-rdma/nvme-tcp fixes from Max, Mark and Me
- Minor cleanups and nits from James, Dan and John
- Two s390 dasd fixes (Jan, Stefan)
- Have loop change block size in DIO mode (Martijn)
- paride pg header ifdef guard (Masahiro)
- Two blk-mq queue scheduler tweaks, fixing an ordering issue on zoned
devices and suboptimal performance on others (Ming)
* tag 'for-linus-2019-10-03' of git://git.kernel.dk/linux-block: (22 commits)
block: sed-opal: fix sparse warning: convert __be64 data
block: sed-opal: fix sparse warning: obsolete array init.
block: pg: add header include guard
Revert "s390/dasd: Add discard support for ESE volumes"
s390/dasd: Fix error handling during online processing
io_uring: use __kernel_timespec in timeout ABI
loop: change queue block size to match when using DIO
blk-mq: apply normal plugging for HDD
blk-mq: honor IO scheduler for multiqueue devices
nvme-rdma: fix possible use-after-free in connect timeout
nvme: Move ctrl sqsize to generic space
nvme: Add ctrl attributes for queue_count and sqsize
nvme: allow 64-bit results in passthru commands
nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T
nvmet-tcp: remove superflous check on request sgl
Added QUIRKs for ADATA XPG SX8200 Pro 512GB
nvme-rdma: Fix max_hw_sectors calculation
nvme: fix an error code in nvme_init_subsystem()
nvme-pci: Save PCI state before putting drive into deepest state
nvme-tcp: fix wrong stop condition in io_work
...
projects / mirror_ubuntu-hirsute-kernel.git / log