Antoine Tenart [Fri, 1 Mar 2019 10:52:13 +0000 (11:52 +0100)]
net: mvpp2: force the XLG MAC link up or down when not using in-band
This patch force the XLG MAC link state in the phylink link_up() and
link_down() helpers when not using in-band auto-negotiation. This mimics
what's already done for the GMAC and follows what's advised in the
phylink documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:12 +0000 (11:52 +0100)]
net: mvpp2: only update the XLG configuration when needed
This patch improves the XLG configuration function, to only update the
XLG configuration register when a change is needed. This helps not
writing over and over the same XLG configuration each time phylink
request the MAC to be configured. This mimics the GMAC configuration
function.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:11 +0000 (11:52 +0100)]
net: mvpp2: always disable both MACs when disabling a port
This patch modifies the port_disable() helper to always disable both the
GMAC and the XLG MAC when called. At boot time we do not know of a port
was enabled in the firmware/bootloader, and if so what mode was used
(hence which of the two MACs was used).
This also help in implementing a logic where all blocks are disabled
when not used, and only enabled regarding the current mode used on a
given port.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:10 +0000 (11:52 +0100)]
net: mvpp2: some AN fields require the link to be down when updated
The GMAC configuration helper modifies values in the auto-negotiation
register. Some of its values require the port to be forced down when
modifying their values. This patches fixes the check made on the bit to
be updated in this register, so that the port is forced down when
needed. This fix cases where some of those parameters were updated, but
not taken into account, such as when using RGMII interfaces.
Fixes: d14e078f23cc ("net: marvell: mvpp2: only reprogram what is necessary on mac_config") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:09 +0000 (11:52 +0100)]
net: mvpp2: fix the computation of the RXQs
The patch fixes the computation of RXQs being used by the PPv2 driver,
which is set depending on the PPv2 engine version and the queue mode
used. There are three cases:
- PPv2.1: 1 RXQ per CPU.
- PPV2.2 with MVPP2_QDIST_MULTI_MODE: 1 RXQ per CPU.
- PPv2.2 with MVPP2_QDIST_SINGLE_MODE: 1 RXQ is shared between the CPUs.
The PPv2 engine supports a maximum of 32 queues per port. This patch
adds a check so that we do not overstep this maximum.
It appeared the calculation was broken for PPv2.1 engines since f8c6ba8424b0, as PPv2.1 ports ended up with a single RXQ while they
needed 4. This patch fixes it.
Fixes: f8c6ba8424b0 ("net: mvpp2: use only one rx queue per port per CPU") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:08 +0000 (11:52 +0100)]
net: mvpp2: fix validate for PPv2.1
The Phylink validate function is the Marvell PPv2 driver makes a check
on the GoP id. This is valid an has to be done when using PPv2.2 engines
but makes no sense when using PPv2.1. The check done when using an RGMII
interface makes sure the GoP id is not 0, but this breaks PPv2.1. Fixes
it.
Fixes: 0fb628f0f250 ("net: mvpp2: fix phylink handling of invalid PHY modes") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:07 +0000 (11:52 +0100)]
net: mvpp2: reconfiguring the port interface is PPv2.2 specific
This patch adds a check on the PPv2 version in-use not to reconfigure
the port mode when an interface is updated when using PPv2.1 as the
functions called are PPv2.2 specific.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:06 +0000 (11:52 +0100)]
net: mvpp2: a port can be disabled even if we use the link IRQ
We had a check in the mvpp2_mac_link_down() function (called by phylink)
to avoid disabling the port when link interrupts are used. It turned out
the interrupt can still be used with the port disabled. We can thus
remove this check.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 1 Mar 2019 10:52:04 +0000 (11:52 +0100)]
net: mvpp2: update the port documentation regarding the GoP
The Marvell PPv2 port structure stores the GoP id of a given port. This
information is specific to PPv2.2, but cannot be used by PPv2.1. Update
its comment to denote this specificity.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4vf: Call netif_carrier_off properly in pci_probe
netif_carrier_off() should be called only after register_netdev().
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reverting force link up changes since this behaviour can be
achieved using VF link state feature.
Reverts:
commit 0913667ab3ad ("cxgb4vf: Forcefully link up virtual interfaces")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Use ndo_set_vf_link_state to control the link states associated
with the virtual interfaces.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4VF.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 28 Feb 2019 23:17:28 +0000 (15:17 -0800)]
net: support 64bit rates for getsockopt(SO_MAX_PACING_RATE)
For legacy applications using 32bit variable, SO_MAX_PACING_RATE
has to cap the returned value to 0xFFFFFFFF, meaning that
rates above 34.35 Gbit are capped.
This patch allows applications to read socket pacing rate
at full resolution, if they provide a 64bit variable to store it,
and the kernel is 64bit.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Bates [Thu, 28 Feb 2019 22:38:40 +0000 (17:38 -0500)]
tc-testing: Allow test cases to be skipped
By adding a check for an optional key/value pair to the test case
data, individual test cases may be skipped to prevent tdc from
aborting a test run due to setup or teardown failure.
If a test case is skipped, it will still appear in the results
output to allow for a consistent number of executed tests in each
run. However, the test will be marked as skipped.
This support for skipping extends to any plugins that may generate
additional results for each executed test.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 2 Mar 2019 05:44:11 +0000 (21:44 -0800)]
Merge branch 'mlxsw-rehash-split'
Ido Schimmel says:
====================
mlxsw: spectrum_acl: Split rehash work into chunks
Jiri says:
When rehash happens on a vregion with many rules and they are being
migrated, it might take significant time to finish the job. During that
time vregion->lock is taken which prevents rules from being
added/deleted from the vregion.
Aim of this patchset is to allow to interrupt migration of rules during
rehash, reschedule and give chance for rules to be added/deleted. Then
continue migration in another execution of scheduled work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Feb 2019 06:59:26 +0000 (06:59 +0000)]
mlxsw: spectrum_acl: Remember where to continue rehash migration
Store pointer to vchunk where the migration was interrupted, as well as
ventry pointer to start from and to stop at (during rollback). This
saved pointers need to be forgotten in case of ventries list or vchunk
list changes, which is done by couple of "changed" helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Feb 2019 06:59:25 +0000 (06:59 +0000)]
mlxsw: spectrum_acl: Allow to interrupt/continue rehash work
Currently, migration of vregions with many entries may take long time
during which insertions and removals of the rules are blocked
due to wait to acquire vregion->lock.
To overcome this, allow to interrupt and continue rehash work according
to the set credits - number of rules to migrate.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Feb 2019 06:59:24 +0000 (06:59 +0000)]
mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()
In order to simplify the code and to prepare it for
interrupted/continued migration process, do the rollback in case of
migration error as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all().
It can be understood as "migrate all back".
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Feb 2019 06:59:24 +0000 (06:59 +0000)]
mlxsw: spectrum_acl: Put vchunk migrate start/end code into separate functions
In preparations of interrupt/continue of rehash work, put the code that
is done at the beginning/end of vchunk migrate function into separate
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Feb 2019 06:59:19 +0000 (06:59 +0000)]
mlxsw: spectrum_acl: Push code start/end from mlxsw_sp_acl_tcam_vregion_migrate()
Push code from the beginning and end of function
mlxsw_sp_acl_tcam_vregion_migrate() into rehash_start()/end() functions.
Then all the things needed to be done before and after the actual
migration process will be grouped together.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the entry is already in a chunk where we want it to be. In that
case, skip migration. This is preparation for "per parts" migration
where this situation may occur.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 28 Feb 2019 00:29:16 +0000 (16:29 -0800)]
switchdev: Remove unused transaction item queue
There are no more in tree users of the
switchdev_trans_item_{dequeue,enqueue} or switchdev_trans_item structure
in the kernel since commit 00fc0c51e35b ("rocker: Change world_ops API
and implementation to be switchdev independant").
Remove this unused code and update the documentation accordingly since.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
doc: net: ieee802154: move from plain text to rst
The ieee802154 subsystem doc was still in plain text. With the networking book
taking shape I thought it was time to do the first step and move it over to rst.
This really is only the minimal conversion. I need to take some time to update
and extend the docs.
The patches are based on net-next, but they only touch the networking book so I
would not expect and trouble. From what I have seen they would go through
Jonathan's tree after being acked by Dave? If you want this patches against a
different tree let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the ieee802154 docs from a plain text file into the new rst
style. This commit only does the minimal needed change to bring the
documentation over. Follow up patches will improve and extend on this.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 27 Feb 2019 19:36:36 +0000 (11:36 -0800)]
devlink: fix kdoc
devlink suffers from a few kdoc warnings:
net/core/devlink.c:5292: warning: Function parameter or member 'dev' not described in 'devlink_register'
net/core/devlink.c:5351: warning: Function parameter or member 'port_index' not described in 'devlink_port_register'
net/core/devlink.c:5753: warning: Function parameter or member 'parent_resource_id' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Function parameter or member 'size_params' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'top_hierarchy' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'reload_required' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'parent_reosurce_id' description in 'devlink_resource_register'
net/core/devlink.c:6451: warning: Function parameter or member 'region' not described in 'devlink_region_snapshot_create'
net/core/devlink.c:6451: warning: Excess function parameter 'devlink_region' description in 'devlink_region_snapshot_create'
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Wed, 27 Feb 2019 12:10:13 +0000 (12:10 +0000)]
net: aquantia: use better wrappers for state registers
Replace some direct registers reads with better
online functions.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Wed, 27 Feb 2019 12:10:11 +0000 (12:10 +0000)]
net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic
David noticed the original define was hiding 'err' variable
reference. Thats confusing and counterintuitive.
Andrew noted the whole macro could be replaced with standard readx_poll
kernel macro. This makes code more readable.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Wed, 27 Feb 2019 12:10:09 +0000 (12:10 +0000)]
net: aquantia: fixed instack structure overflow
This is a real stack undercorruption found by kasan build.
The issue did no harm normally because it only overflowed
2 bytes after `bitary` array which on most architectures
were mapped into `err` local.
Fixes: bab6de8fd180 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In reality msix_entry_mask always restricts number of iterations.
Adding extra condition to make logic clear and smatch happy.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Wed, 27 Feb 2019 12:10:05 +0000 (12:10 +0000)]
net: aquantia: added newline at end of file
drivers/net/ethernet/aquantia/atlantic/aq_nic.c: 991:1:
warning: no newline at end of file
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Wed, 27 Feb 2019 12:10:03 +0000 (12:10 +0000)]
net: aquantia: fixed memcpy size
Not careful array dereference caused analysis tools
to think there could be memory overflow.
There was actually no corruption because the array is
two dimensional.
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c: 140
aq_ethtool_get_strings() error:
memcpy() '*aq_ethtool_stat_names' too small (32 vs 704)
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nfp: control processor DMA support and RJ45
This series starts with adding support for reporting twisted pair
media type in ethtool.
Remaining patches add support for using DMA with the control/service
processor. Currently we always copy the command data into card's
memory. DMA support allows us to have the NSP read the data from
host memory by itself. Unfortunately, the FW loading and flashing
cannot directly map the buffers for DMA because (a) the firmware
ABI returns const buffers, and (b) the buffers may be vmalloc()ed
in many mysterious/unmappable way. So just bite the bullet -
allocate new host buffer for the command and copy.
As Dirk explains, the NSP now supports updating all FWs at once
which means the max flashing time grew significantly. He bumps
the max wait to avoid timeouts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware now supports being passed a bundle with
multiple components to be stored in flash at once. This makes it
easier to update all components to a known state with a single
user command, however, this also has the potential to increase
the time required to perform the update significantly.
The management firmware only updates the components out of a bundle
which are outdated, however, we need to make sure we can handle
the absolute worst case where a CPLD update can take a long time
to perform.
We set a very conservative total timeout of 900s which already
adds a contingency.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 27 Feb 2019 04:19:32 +0000 (20:19 -0800)]
nfp: nsp: allow the use of DMA buffer
Newer versions of NSP can access host memory. Simplest access
type requires all data to be in one contiguous area. Since we
don't have the guarantee on where callers of the NSP ABI will
allocate their buffers we allocate a bounce buffer and copy
the data in and out.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 27 Feb 2019 04:19:31 +0000 (20:19 -0800)]
nfp: nsp: move default buffer handling into its own function
DMA version of NSP communication is coming, move the code which
copies data into the NFP buffer into a separate function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 27 Feb 2019 04:19:30 +0000 (20:19 -0800)]
nfp: nsp: use fractional size of the buffer
NSP expresses the buffer size in MB and 4 kB blocks. For small
buffers the kB part may make a difference, so count it in.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 25 Feb 2019 16:43:03 +0000 (17:43 +0100)]
net: marvell: neta: disable comphy when setting mode
The comphy driver for Armada 3700 by Miquèl Raynal (which is currently
in linux-next) does not actually set comphy mode when phy_set_mode_ext
is called. The mode is set at next call of phy_power_on.
Update the driver to semantics similar to mvpp2: helper
mvneta_comphy_init sets comphy mode and powers it on.
When mode is to be changed in mvneta_mac_config, first power the comphy
off, then call mvneta_comphy_init (which sets the mode to new one).
Only do this when new mode is different from old mode.
This should also work for Armada 38x, since in that comphy driver
methods power_on and power_off are unimplemented.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
enetc: Add mdio support and device tree nodes
This is the missing part to enable PCI probing of the ENETC ethernet
ports on the LS1028A SoC and external traffic on the LS1028A RDB board.
It's one of the first items on the TODO list for the recently merged
ENETC ethernet driver.
Claudiu Manoil [Tue, 26 Feb 2019 13:42:22 +0000 (15:42 +0200)]
enetc: Add ENETC PF level external MDIO support
Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 26 Feb 2019 13:42:21 +0000 (15:42 +0200)]
arm64: dts: fsl: ls1028a-rdb: Add ENETC external eth ports for the LS1028A RDB board
The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0). ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.
The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF. Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 28 Feb 2019 19:22:58 +0000 (11:22 -0800)]
selftests: rtnetlink: use internal netns switch for ip commands
'ip' can switch network namespaces internally and then run a given
command relative to that namespace without the need to fork and exec
another ip instance. Update all references of the form:
ip netns exec "$testns" ip ...
to
ip -netns "$testns" ...
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
please apply one more qeth patch series for net-next. This eliminates
some of the quirks in our reset code, and slims down the internal
state machine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:44 +0000 (18:59 +0100)]
s390/qeth: drop redundant state checking
Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:43 +0000 (18:59 +0100)]
s390/qeth: don't special-case HW trap during suspend
It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
HW trap for us.
So consolidate the two code paths in the suspend callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:40 +0000 (18:59 +0100)]
s390/qeth: remove a redundant check for card->dev
smatch complains that __qeth_l3_set_offline() first accesses card->dev,
and then later checks whether the pointer is valid.
Since commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), the
pointer is _always_ valid - that patch merely missed to remove this one
check.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:39 +0000 (18:59 +0100)]
s390/qeth: call dev_close() during recovery
When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.
It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:
- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.
- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.
- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:38 +0000 (18:59 +0100)]
s390/qeth: unconditionally clear MAC_REGISTERED flag
In its attempt to run only the minimal amount of tear down steps,
qeth_l2_stop_card() fails to reset the "is dev_addr registered?" flag
in some rare scenarios. But a future change to the tear down sequence
would cause us to _always_ hit this issue, so patch it up before that
code lands.
Fix it by unconditionally clearing the flag bit. This also allows us to
remove the additional cleanup step in qeth_dev_layer2_store().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:37 +0000 (18:59 +0100)]
s390/qeth: enable/disable the HW trap a little earlier
When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.
In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Thu, 28 Feb 2019 17:59:36 +0000 (18:59 +0100)]
s390/qeth: remove RECOVER state
The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.
Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Thu, 28 Feb 2019 14:10:08 +0000 (15:10 +0100)]
net/smc: allow pnetid-less configuration
Without hardware pnetid support there must currently be a pnet
table configured to determine the IB device port to be used for SMC
RDMA traffic. This patch enables a setup without pnet table, if
the used handshake interface belongs already to a RoCE port.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Leslie Monis [Thu, 28 Feb 2019 12:36:54 +0000 (18:06 +0530)]
net: sched: pie: avoid slow division in drop probability decay
As per RFC 8033, it is sufficient for the drop probability
decay factor to have a value of (1 - 1/64) instead of 98%.
This avoids the need to do slow division.
Suggested-by: David Laight <David.Laight@aculab.com> Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Thu, 28 Feb 2019 10:03:16 +0000 (15:33 +0530)]
cxgb4vf: Enter debugging mode if FW is inaccessible
If we are not able to reach firmware, enter debugging mode that will
help us to get adapter logs.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Thu, 28 Feb 2019 09:39:28 +0000 (15:09 +0530)]
cxgb4: Enable outer UDP checksum offload for T6
T6 adapters support outer UDP checksum offload for
encapsulated packets, hence enabling netdev feature flag
NETIF_F_GSO_UDP_TUNNEL_CSUM.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Vynipadath [Thu, 28 Feb 2019 09:36:54 +0000 (15:06 +0530)]
cxgb4/cxgb4vf: Fix up netdev->hw_features
GRO is done by cxgb4/cxgb4vf. Hence set NETIF_F_GRO flag for
both cxgb4/cxgb4vf.
Cleaned up VLAN netdev features in cxgb4vf. Also fixed
NETIF_F_HIGHDMA being set unconditionally for vlan netdev
features.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Britstein [Tue, 26 Feb 2019 09:57:34 +0000 (09:57 +0000)]
net: sched: act_csum: Fix csum calc for tagged packets
The csum calculation is different for IPv4/6. For VLAN packets,
tc_skb_protocol returns the VLAN protocol rather than the packet's one
(e.g. IPv4/6), so csum is not calculated. Furthermore, VLAN may not be
stripped so csum is not calculated in this case too. Calculate the
csum for those cases.
Fixes: d8b9605d2697 ("net: sched: fix skb->protocol use in case of accelerated vlan path") Signed-off-by: Eli Britstein <elibr@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
====================
net: phy: marvell10g: Clean .get_features by using C45 helpers
Recent work on C45 helpers by Heiner made the
genphy_c45_pma_read_abilities function generic enough to use as a
default .get_featutes implementation.
This series removes the remaining redundant code in
mv3310_get_features(), and makes the 2110 PHY use
genphy_c45_pma_read_abilities() directly, since it doesn't have the
issue with the wrong abilities being reported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Use the generic C45 helper to read the 2110 features
Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Let genphy_c45_pma_read_abilities set Aneg bit
The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.
We therefore don't need to manually do that in mv3310_get_features().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Mon, 25 Feb 2019 15:30:14 +0000 (17:30 +0200)]
net: sched: act_tunnel_key: fix metadata handling
Tunnel key action params->tcft_enc_metadata is only set when action is
TCA_TUNNEL_KEY_ACT_SET. However, metadata pointer is incorrectly
dereferenced during tunnel key init and release without verifying that
action is if correct type, which causes NULL pointer dereference. Metadata
tunnel dst_cache is also leaked on action overwrite.
Fix metadata handling:
- Verify that metadata pointer is not NULL before dereferencing it in
tunnel_key_init error handling code.
- Move dst_cache destroy code into tunnel_key_release_params() function
that is called in both action overwrite and release cases (fixes resource
leak) and verifies that actions has correct type before dereferencing
metadata pointer (fixes NULL pointer dereference).
Oops with KASAN enabled during tdc tests execution:
Fixes: 41411e2fd6b8 ("net/sched: act_tunnel_key: Add dst_cache support") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pankaj Bansal [Mon, 25 Feb 2019 06:16:53 +0000 (06:16 +0000)]
dt-bindings: net: Add bindings for mdio mux consumers
When we use the bindings defined in Documentation/devicetree/bindings/mux
to define mdio mux in producer and consumer terms, it results in two
devices. one is mux producer and other is mux consumer.
Add the bindings needed for Mdio mux consumer devices.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu [Sun, 24 Feb 2019 03:36:20 +0000 (11:36 +0800)]
route: Add multipath_hash in flowi_common to make user-define hash
Current fib_multipath_hash_policy can make hash based on the L3 or
L4. But it only work on the outer IP. So a specific tunnel always
has the same hash value. But a specific tunnel may contain so many
inner connections.
This patch provide a generic multipath_hash in floi_common. It can
make a user-define hash which can mix with L3 or L4 hash.
Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Feb 2019 20:39:56 +0000 (12:39 -0800)]
Merge branch 'net-Remove-switchdev_ops'
Florian Fainelli says:
====================
net: Remove switchdev_ops
This patch series completes the removal of the switchdev_ops by
converting switchdev_port_attr_set() to use either the blocking
(process) or non-blocking (atomic) notifier since we typically need to
deal with both depending on where in the bridge code we get called from.
This was tested with the forwarding selftests and DSA hardware.
Ido, hopefully this captures your comments done on v1, if not, can you
illustrate with some pseudo-code what you had in mind if that's okay?
Changes in v3:
- added Reviewed-by tags from Ido where relevant
- added missing notifier_to_errno() in net/bridge/br_switchdev.c when
calling the atomic notifier for PRE_BRIDGE_FLAGS
- kept mlxsw_sp_switchdev_init() in mlxsw/
Changes in v2:
- do not check for SWITCHDEV_F_DEFER when calling the blocking notifier
and instead directly call the atomic notifier from the single location
where this is required
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:32 +0000 (11:44 -0800)]
net: Remove switchdev_ops
Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:31 +0000 (11:44 -0800)]
net: switchdev: Replace port attr set SDO with a notification
Drop switchdev_ops.switchdev_port_attr_set. Drop the uses of this field
from all clients, which were migrated to use switchdev notification in
the previous patches.
Add a new function switchdev_port_attr_notify() that sends the switchdev
notifications SWITCHDEV_PORT_ATTR_SET and calls the blocking (process)
notifier chain.
We have one odd case within net/bridge/br_switchdev.c with the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier that
requires executing from atomic context, we deal with that one
specifically.
Drop __switchdev_port_attr_set() and update switchdev_port_attr_set()
likewise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way we communicate setting a port's
attribute and use a blocking notifier to perform those tasks.
Prepare ethsw to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET and simply translate that into the existing
swdev_port_attr_set() call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:29 +0000 (11:44 -0800)]
net: mscc: ocelot: Handle SWITCHDEV_PORT_ATTR_SET
Following patches will change the way we communicate setting a port's
attribute and use notifiers to perform those tasks.
Ocelot does not currently have an atomic notifier registered for
switchdev events, so we need to register one in order to deal with
atomic context SWITCHDEV_PORT_ATTR_SET events.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way we communicate setting a port's
attribute and use a notifier to perform those tasks.
Prepare mlxsw to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET and utilize the switchdev_handle_port_attr_set()
to handle stacking of devices.
Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:27 +0000 (11:44 -0800)]
net: dsa: Handle SWITCHDEV_PORT_ATTR_SET
Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.
Prepare DSA to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
dsa_slave_port_attr_set() can process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:26 +0000 (11:44 -0800)]
rocker: Handle SWITCHDEV_PORT_ATTR_SET
Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.
Prepare rocker to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
rocker_port_attr_set() can process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 27 Feb 2019 19:44:25 +0000 (11:44 -0800)]
switchdev: Add SWITCHDEV_PORT_ATTR_SET
In preparation for allowing switchdev enabled drivers to veto specific
attribute settings from within the context of the caller, introduce a
new switchdev notifier type for port attributes.
Suggested-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Wed, 27 Feb 2019 13:49:17 +0000 (15:49 +0200)]
Revert "net: sched: fw: don't set arg->stop in fw_walk() when empty"
This reverts commit 31a998487641 ("net: sched: fw: don't set arg->stop in
fw_walk() when empty")
Cls API function tcf_proto_is_empty() was changed in commit 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty")
to no longer depend on arg->stop to determine that classifier instance is
empty. Instead, it adds dedicated arg->nonempty field, which makes the fix
in fw classifier no longer necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Wed, 27 Feb 2019 12:47:57 +0000 (20:47 +0800)]
ethtool: Use explicit designated initializers for .cmd
Initialize the .cmd member by using a designated struct
initializer. This fixes warning of missing field initializers,
and makes code a little easier to read.
Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Leslie Monis [Wed, 27 Feb 2019 01:00:06 +0000 (06:30 +0530)]
net: sched: pie: fix 64-bit division
Use div_u64() to resolve build failures on 32-bit platforms.
Fixes: 3f7ae5f3dc52 ("net: sched: pie: add more cases to auto-tune alpha and beta") Signed-off-by: Leslie Monis <lesliemonis@gmail.com> Reported-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log