Dmitry Osipenko [Sat, 24 Nov 2018 21:13:48 +0000 (00:13 +0300)]
ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+
The external memory arbitration configuration is getting reset after
memory entering into self-refresh mode, it shall be restored on the
exit. Note that MC_EMEM_ARB_CFG register is shadowed and latching
happens on the EMC timing update. This fixes 2x GPU performance
degradation after resuming from LP1 on Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Sat, 24 Nov 2018 21:13:47 +0000 (00:13 +0300)]
ARM: tegra: Fix DRAM refresh-interval clobbering on resume from LP1 on Tegra30
The DRAM refresh-interval is getting erroneously set to "1" on exiting
from memory self-refreshing mode. The clobbered interval causes the
"refresh request overflow timeout" error raised by the External Memory
Controller on exiting from LP1 on Tegra30. The same may happen on Tegra20,
but EMC registers are not latched after exiting from self-refreshing mode
on Tegra20 and hence refresh-interval is not altered until an event that
causes registers latching happens.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Sat, 24 Nov 2018 21:13:46 +0000 (00:13 +0300)]
ARM: tegra: Fix missed EMC registers latching on resume from LP1 on Tegra30+
The memory interface configuration and re-calibration interval are left
unassigned on resume from LP1 because these registers are shadowed and
require latching after being adjusted.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Linus Torvalds [Mon, 7 Jan 2019 00:33:10 +0000 (16:33 -0800)]
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Linus Torvalds [Mon, 7 Jan 2019 00:30:14 +0000 (16:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
Linus Torvalds [Sun, 6 Jan 2019 01:50:59 +0000 (17:50 -0800)]
Change mincore() to count "mapped" pages rather than "cached" pages
The semantics of what "in core" means for the mincore() system call are
somewhat unclear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache" rather than "page is mapped in the mapping".
The problem with that traditional semantic is that it exposes a lot of
system cache state that it really probably shouldn't, and that users
shouldn't really even care about.
So let's try to avoid that information leak by simply changing the
semantics to be that mincore() counts actual mapped pages, not pages
that might be cheaply mapped if they were faulted (note the "might be"
part of the old semantics: being in the cache doesn't actually guarantee
that you can access them without IO anyway, since things like network
filesystems may have to revalidate the cache before use).
In many ways the old semantics were somewhat insane even aside from the
information leak issue. From the very beginning (and that beginning is
a long time ago: 2.3.52 was released in March 2000, I think), the code
had a comment saying
Later we can get more picky about what "in core" means precisely.
and this is that "later". Admittedly it is much later than is really
comfortable.
NOTE! This is a real semantic change, and it is for example known to
change the output of "fincore", since that program literally does a
mmmap without populating it, and then doing "mincore()" on that mapping
that doesn't actually have any pages in it.
I'm hoping that nobody actually has any workflow that cares, and the
info leak is real.
We may have to do something different if it turns out that people have
valid reasons to want the old semantics, and if we can limit the
information leak sanely.
Cc: Kevin Easton <kevin@guarana.org> Cc: Jiri Kosina <jikos@kernel.org> Cc: Masatake YAMATO <yamato@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 19:15:04 +0000 (11:15 -0800)]
Fix 'acccess_ok()' on alpha and SH
Commit 594cc251fdd0 ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net> Cc: Matt Turner <mattst88@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 20:19:23 +0000 (12:19 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Fix a number of ext4 bugs"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix special inode number checks in __ext4_iget()
ext4: track writeback errors using the generic tracking infrastructure
ext4: use ext4_write_inode() when fsyncing w/o a journal
ext4: avoid kernel warning when writing the superblock to a dead device
ext4: fix a potential fiemap/page fault deadlock w/ inline_data
ext4: make sure enough credits are reserved for dioread_nolock writes
Linus Torvalds [Sun, 6 Jan 2019 19:47:26 +0000 (11:47 -0800)]
Merge tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions introduced in this cycles:
- fix dma-debug tracking for the map_page / map_single
consolidatation
- properly stub out DMA mapping symbols for !HAS_DMA builds to avoid
link failures
- fix AMD Gart direct mappings
- setup the dma address for no kernel mappings using the remap
allocator"
* tag 'dma-mapping-4.21-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING for remapped allocations
x86/amd_gart: fix unmapping of non-GART mappings
dma-mapping: remove a few unused exports
dma-mapping: properly stub out the DMA API for !CONFIG_HAS_DMA
dma-mapping: remove dmam_{declare,release}_coherent_memory
dma-mapping: implement dmam_alloc_coherent using dmam_alloc_attrs
dma-mapping: implement dma_map_single_attrs using dma_map_page_attrs
Linus Torvalds [Sun, 6 Jan 2019 19:40:06 +0000 (11:40 -0800)]
Merge tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- Changes for EC_MKBP_EVENT_SENSOR_FIFO handling.
- Also, maintainership changes. Olofj out, Enric balletbo in.
* tag 'tag-chrome-platform-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
MAINTAINERS: add maintainers for ChromeOS EC sub-drivers
MAINTAINERS: platform/chrome: Add Enric as a maintainer
MAINTAINERS: platform/chrome: remove myself as maintainer
platform/chrome: don't report EC_MKBP_EVENT_SENSOR_FIFO as wakeup
platform/chrome: straighten out cros_ec_get_{next,host}_event() error codes
Eric Biggers [Sun, 6 Jan 2019 13:36:21 +0000 (08:36 -0500)]
fscrypt: add Adiantum support
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit 059c2a4d8e16 ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Sun, 6 Jan 2019 02:35:02 +0000 (18:35 -0800)]
Merge tag 'docs-5.0-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"
* tag 'docs-5.0-fixes' of git://git.lwn.net/linux:
doc: filesystems: fix bad references to nonexistent ext4.rst file
Documentation/admin-guide: update URL of LKML information link
Docs/kernel-api.rst: Remove blk-tag.c reference
Linus Torvalds [Sun, 6 Jan 2019 02:33:21 +0000 (18:33 -0800)]
Merge tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fixlet from Stefan Richter:
"Remove an explicit dependency in Kconfig which is implied by another
dependency"
* tag 'firewire-update' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: Remove depends on HAS_DMA in case of platform dependency
Linus Torvalds [Sun, 6 Jan 2019 02:29:13 +0000 (18:29 -0800)]
Merge tag 'for-linus-20190104' of git://git.kernel.dk/linux-block
Pull block updates and fixes from Jens Axboe:
- Pulled in MD changes that Shaohua had queued up for 4.21.
Unfortunately we lost Shaohua late 2018, I'm sending these in on his
behalf.
- In conjunction with the above, I added a CREDITS entry for Shaoua.
- sunvdc queue restart fix (Ming)
* tag 'for-linus-20190104' of git://git.kernel.dk/linux-block:
Add CREDITS entry for Shaohua Li
block: sunvdc: don't run hw queue synchronously from irq context
md: fix raid10 hang issue caused by barrier
raid10: refactor common wait code from regular read/write request
md: remvoe redundant condition check
lib/raid6: add option to skip algo benchmarking
lib/raid6: sort algos in rough performance order
lib/raid6: check for assembler SSSE3 support
lib/raid6: avoid __attribute_const__ redefinition
lib/raid6: add missing include for raid6test
md: remove set but not used variable 'bi_rdev'
Linus Torvalds [Sun, 6 Jan 2019 02:25:19 +0000 (18:25 -0800)]
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Linus Torvalds [Sun, 6 Jan 2019 02:20:51 +0000 (18:20 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Over the break a few defects were found, so this is a -rc style pull
request of various small things that have been posted.
- An attempt to shorten RCU grace period driven delays showed crashes
during heavier testing, and has been entirely reverted
- A missed merge/rebase error between the advise_mr and ib_device_ops
series
- Some small static analysis driven fixes from Julia and Aditya
- Missed ability to create a XRC_INI in the devx verbs interop
series"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
infiniband/qedr: Potential null ptr dereference of qp
infiniband: bnxt_re: qplib: Check the return value of send_message
IB/ipoib: drop useless LIST_HEAD
IB/core: Add advise_mr to the list of known ops
Revert "IB/mlx5: Fix long EEH recover time with NVMe offloads"
IB/mlx5: Allow XRC INI usage via verbs in DEVX context
Linus Torvalds [Sun, 6 Jan 2019 02:15:37 +0000 (18:15 -0800)]
Merge tag 'fbdev-v4.21' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"This time the pull request is really small.
The most notable changes are fixing fbcon to not cause crash on
unregister_framebuffer() operation when there is more than one
framebuffer, adding config option to center the bootup logo and making
FB_BACKLIGHT config option tristate (which in turn uncovered incorrect
FB_BACKLIGHT usage by DRM's nouveau driver).
Summary:
- fix fbcon to not cause crash on unregister_framebuffer() when there
is more than one framebuffer (Noralf Trønnes)
- improve support for small rotated displays (Peter Rosin)
- fix probe failure handling in udlfb driver (Dan Carpenter)
- add config option to center the bootup logo (Peter Rosin)
- make FB_BACKLIGHT config option tristate (Rob Clark)
- remove superfluous HAS_DMA dependency for goldfishfb driver (Geert
Uytterhoeven)
- misc fixes (Alexey Khoroshilov, YueHaibing, Colin Ian King, Lubomir
Rintel)
- misc cleanups (Yangtao Li, Wen Yang)
also there is DRM's nouveau driver fix for wrong FB_BACKLIGHT config
option usage (FB_BACKLIGHT is for internal fbdev subsystem use only)"
* tag 'fbdev-v4.21' of git://github.com/bzolnier/linux:
drm/nouveau: fix incorrect FB_BACKLIGHT usage in Kconfig
fbdev: fbcon: Fix unregister crash when more than one framebuffer
fbdev: Remove depends on HAS_DMA in case of platform dependency
pxa168fb: trivial typo fix
fbdev: fsl-diu: remove redundant null check on cmap
fbdev: omap2: omapfb: convert to DEFINE_SHOW_ATTRIBUTE
fbdev: uvesafb: fix spelling mistake "memoery" -> "memory"
fbdev: fbmem: add config option to center the bootup logo
fbdev: fbmem: make fb_show_logo_line return the end instead of the height
video: fbdev: pxafb: Fix "WARNING: invalid free of devm_ allocated data"
fbdev: fbmem: behave better with small rotated displays and many CPUs
video: clps711x-fb: release disp device node in probe()
fbdev: make FB_BACKLIGHT a tristate
udlfb: fix some inconsistent NULL checking
Linus Torvalds [Sun, 6 Jan 2019 02:13:35 +0000 (18:13 -0800)]
Merge branch 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has only driver updates for you this time.
Mostly new IDs/DT compatibles, also SPDX conversions, small cleanups.
STM32F7 got FastMode+ and PM support, Axxia some reliabilty
improvements"
* 'i2c/for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: Add Actions Semiconductor Owl family S700 I2C support
dt-bindings: i2c: Add S700 support for Actions Semi Soc's
i2c: ismt: Add support for Intel Cedar Fork
i2c: tegra: Switch to SPDX identifier
i2c: tegra: Add missing kerneldoc for some fields
i2c: tegra: Cleanup kerneldoc comments
i2c: axxia: support sequence command mode
dt-bindings: i2c: rcar: Add r8a774c0 support
dt-bindings: i2c: sh_mobile: Add r8a774c0 support
i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)
i2c: i2c-cros-ec-tunnel: Switch to SPDX identifier.
i2c: powermac: Use of_node_name_eq for node name comparisons
i2c-axxia: check for error conditions first
i2c-axxia: dedicated function to set client addr
dt-bindings: i2c: Use correct vendor prefix for Atmel
i2c: tegra: replace spin_lock_irqsave with spin_lock in ISR
eeprom: at24: add support for 24c2048
dt-bindings: eeprom: at24: add "atmel,24c2048" compatible string
i2c: i2c-stm32f7: add PM Runtime support
i2c: sh_mobile: add support for r8a77990 (R-Car E3)
...
Linus Torvalds [Sun, 6 Jan 2019 01:53:40 +0000 (17:53 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- high-resolution scrolling support that gracefully handles differences
between MS and Logitech implementations in HW, from Peter Hutterer
and Harry Cutts
- MSI IRQ support for intel-ish driver, from Song Hongyan
- support for new hardware (Cougar 700K, Odys Winbook 13, ASUS FX503VD,
ASUS T101HA) from Daniel M. Lambea, Hans de Goede and Aleix Roca
Nonell
- other small assorted fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (22 commits)
HID: i2c-hid: Add Odys Winbook 13 to descriptor override
HID: lenovo: Add checks to fix of_led_classdev_register
HID: intel-ish-hid: add MSI interrupt support
HID: debug: Change to use DEFINE_SHOW_ATTRIBUTE macro
HID: doc: fix wrong data structure reference for UHID_OUTPUT
HID: intel-ish-hid: fixes incorrect error handling
HID: asus: Add support for the ASUS T101HA keyboard dock
HID: logitech: Use LDJ_DEVICE macro for existing Logitech mice
HID: logitech: Enable high-resolution scrolling on Logitech mice
HID: logitech: Add function to enable HID++ 1.0 "scrolling acceleration"
HID: logitech-hidpp: fix typo, hiddpp to hidpp
HID: input: use the Resolution Multiplier for high-resolution scrolling
HID: core: process the Resolution Multiplier
HID: core: store the collections as a basic tree
Input: add `REL_WHEEL_HI_RES` and `REL_HWHEEL_HI_RES`
HID: input: support Microsoft wireless radio control hotkey
HID: use macros in IS_INPUT_APPLICATION
HID: asus: Add support for the ASUS FX503VD laptop
HID: asus: Add event handler to catch unmapped Asus Vendor UsagePage codes
HID: cougar: Add support for Cougar 700K Gaming Keyboard
...
Masahiro Yamada [Thu, 3 Jan 2019 01:10:39 +0000 (10:10 +0900)]
arch: remove redundant UAPI generic-y defines
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Thu, 3 Jan 2019 01:10:38 +0000 (10:10 +0900)]
kbuild: generate asm-generic wrappers if mandatory headers are missing
Some time ago, Sam pointed out a certain degree of overwrap between
generic-y and mandatory-y. (https://lkml.org/lkml/2017/7/10/121)
I tweaked the meaning of mandatory-y a little bit; now it defines the
minimum set of ASM headers that all architectures must have.
If arch does not have specific implementation of a mandatory header,
Kbuild will let it fallback to the asm-generic one by automatically
generating a wrapper. This will allow to drop lots of redundant
generic-y defines.
Previously, "mandatory" was used in the context of UAPI, but I guess
this can be extended to kernel space ASM headers.
Suggested-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Masahiro Yamada [Mon, 31 Dec 2018 08:24:09 +0000 (17:24 +0900)]
kbuild: change filechk to surround the given command with { }
filechk_* rules often consist of multiple 'echo' lines. They must be
surrounded with { } or ( ) to work correctly. Otherwise, only the
string from the last 'echo' would be written into the target.
Let's take care of that in the 'filechk' in scripts/Kbuild.include
to clean up filechk_* rules.
Masahiro Yamada [Mon, 31 Dec 2018 04:09:00 +0000 (13:09 +0900)]
kbuild: clean up rule_dtc_dt_yaml
Commit 3a2429e1faf4 ("kbuild: change if_changed_rule for multi-line
recipe") and commit 4f0e3a57d6eb ("kbuild: Add support for DT binding
schema checks") came in via different sub-systems.
Mathias Krause [Sun, 30 Dec 2018 12:36:00 +0000 (13:36 +0100)]
kallsyms: lower alignment on ARM
As mentioned in the info pages of gas, the '.align' pseudo op's
interpretation of the alignment value is architecture specific.
It might either be a byte value or taken to the power of two.
On ARM it's actually the latter which leads to unnecessary large
alignments of 16 bytes for 32 bit builds or 256 bytes for 64 bit
builds.
Fix this by switching to '.balign' instead which is consistent
across all architectures.
Julia Lawall [Sat, 29 Dec 2018 06:14:16 +0000 (07:14 +0100)]
scripts: coccinelle: boolinit: drop warnings on named constants
Coccinelle doesn't always have access to the values of named
(#define) constants, and they may likely often be bound to true
and false values anyway, resulting in false positives. So stop
warning about them.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linus Torvalds [Sun, 6 Jan 2019 00:07:28 +0000 (16:07 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Add locking for cooling device sysfs attribute in case the cooling
device state is changed by userspace and thermal framework
simultaneously. (Thara Gopinath)
- Fix a problem that passive cooling is reset improperly after system
suspend/resume. (Wei Wang)
- Cleanup the driver/thermal/ directory by moving intel and qcom
platform specific drivers to platform specific sub-directories. (Amit
Kucheria)
- Some trivial cleanups. (Lukasz Luba, Wolfram Sang)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/intel: fixup for Kconfig string parsing tightening up
drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir
drivers: thermal: Move various drivers for intel platforms into a subdir
thermal: Fix locking in cooling device sysfs update cur_state
Thermal: do not clear passive state during system sleep
thermal: zx2967_thermal: simplify getting .driver_data
thermal: st: st_thermal: simplify getting .driver_data
thermal: spear_thermal: simplify getting .driver_data
thermal: rockchip_thermal: simplify getting .driver_data
thermal: int340x_thermal: int3400_thermal: simplify getting .driver_data
thermal: remove unused function parameter
Linus Torvalds [Sun, 6 Jan 2019 00:01:16 +0000 (16:01 -0800)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC updates from Eduardo Valentin:
- Tegra DT binding documentation for Tegra194
- Armada now supports ap806 and cp110
- RCAR thermal now supports R8A774C0 and R8A77990
- Fixes on thermal_hwmon, IMX, generic-ADC, ST, RCAR, Broadcom,
Uniphier, QCOM, Tegra, PowerClamp, and Armada thermal drivers.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (22 commits)
thermal: generic-adc: Fix adc to temp interpolation
thermal: rcar_thermal: add R8A77990 support
dt-bindings: thermal: rcar-thermal: add R8A77990 support
thermal: rcar_thermal: add R8A774C0 support
dt-bindings: thermal: rcar-thermal: add R8A774C0 support
dt-bindings: cp110: document the thermal interrupt capabilities
dt-bindings: ap806: document the thermal interrupt capabilities
MAINTAINERS: thermal: add entry for Marvell MVEBU thermal driver
thermal: armada: add overheat interrupt support
thermal: st: fix Makefile typo
thermal: uniphier: Convert to SPDX identifier
thermal/intel_powerclamp: Change to use DEFINE_SHOW_ATTRIBUTE macro
thermal: tegra: soctherm: Change to use DEFINE_SHOW_ATTRIBUTE macro
dt-bindings: thermal: tegra-bpmp: Add Tegra194 support
thermal: imx: save one condition block for normal case of nvmem initialization
thermal: imx: fix for dependency on cpu-freq
thermal: tsens: qcom: do not create duplicate regmap debugfs entries
thermal: armada: Use PTR_ERR_OR_ZERO in armada_thermal_probe_legacy()
dt-bindings: thermal: rcar-gen3-thermal: All variants use 3 interrupts
thermal: broadcom: use devm_thermal_zone_of_sensor_register
...
Linus Torvalds [Sat, 5 Jan 2019 22:08:00 +0000 (14:08 -0800)]
Merge tag 'trace-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace sh build fix from Steven Rostedt:
"It appears that the zero-day bot did find a bug in my sh build.
And that I didn't have the bad code in my config file when I cross
compiled it, although there are a few other errors in sh that makes it
not build for me, I missed that I added one more"
* tag 'trace-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
sh: ftrace: Fix missing parenthesis in WARN_ON()
Linus Torvalds [Sat, 5 Jan 2019 22:05:06 +0000 (14:05 -0800)]
Merge tag '4.21-smb3-small-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
"Three fixes, one for stable, one adds the (most secure) SMB3.1.1
dialect to default list requested"
* tag '4.21-smb3-small-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: add smb3.1.1 to default dialect list
cifs: fix confusing warning message on reconnect
smb3: fix large reads on encrypted connections
Linus Torvalds [Sat, 5 Jan 2019 22:02:22 +0000 (14:02 -0800)]
Merge tag 'iomap-4.21-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap maintainer update from Darrick Wong:
"Christoph Hellwig and I have decided to take responsibility for the fs
iomap code rather than let it languish further"
* tag 'iomap-4.21-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: take responsibility for the filesystem iomap code
Linus Torvalds [Sat, 5 Jan 2019 21:58:08 +0000 (13:58 -0800)]
Merge tag 'ceph-for-4.21-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"A fairly quiet round: a couple of messenger performance improvements
from myself and a few cap handling fixes from Zheng"
* tag 'ceph-for-4.21-rc1' of git://github.com/ceph/ceph-client:
ceph: don't encode inode pathes into reconnect message
ceph: update wanted caps after resuming stale session
ceph: skip updating 'wanted' caps if caps are already issued
ceph: don't request excl caps when mount is readonly
ceph: don't update importing cap's mseq when handing cap export
libceph: switch more to bool in ceph_tcp_sendmsg()
libceph: use MSG_SENDPAGE_NOTLAST with ceph_tcp_sendpage()
libceph: use sock_no_sendpage() as a fallback in ceph_tcp_sendpage()
libceph: drop last_piece logic from write_partial_message_data()
ceph: remove redundant assignment
ceph: cleanup splice_dentry()
Olof Johansson [Sat, 5 Jan 2019 21:21:18 +0000 (13:21 -0800)]
lib/genalloc.c: include vmalloc.h
Fixes build break on most ARM/ARM64 defconfigs:
lib/genalloc.c: In function 'gen_pool_add_virt':
lib/genalloc.c:190:10: error: implicit declaration of function 'vzalloc_node'; did you mean 'kzalloc_node'?
lib/genalloc.c:190:8: warning: assignment to 'struct gen_pool_chunk *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
lib/genalloc.c: In function 'gen_pool_destroy':
lib/genalloc.c:254:3: error: implicit declaration of function 'vfree'; did you mean 'kfree'?
Fixes: 6862d2fc8185 ('lib/genalloc.c: use vzalloc_node() to allocate the bitmap') Cc: Huang Shijie <sjhuang@iluvatar.ai> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Skidanov <alexey.skidanov@intel.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 5 Jan 2019 21:25:58 +0000 (13:25 -0800)]
Merge branch 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs mount API prep from Al Viro:
"Mount API prereqs.
Mostly that's LSM mount options cleanups. There are several minor
fixes in there, but nothing earth-shattering (leaks on failure exits,
mostly)"
* 'mount.part1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (27 commits)
mount_fs: suppress MAC on MS_SUBMOUNT as well as MS_KERNMOUNT
smack: rewrite smack_sb_eat_lsm_opts()
smack: get rid of match_token()
smack: take the guts of smack_parse_opts_str() into a new helper
LSM: new method: ->sb_add_mnt_opt()
selinux: rewrite selinux_sb_eat_lsm_opts()
selinux: regularize Opt_... names a bit
selinux: switch away from match_token()
selinux: new helper - selinux_add_opt()
LSM: bury struct security_mnt_opts
smack: switch to private smack_mnt_opts
selinux: switch to private struct selinux_mnt_opts
LSM: hide struct security_mnt_opts from any generic code
selinux: kill selinux_sb_get_mnt_opts()
LSM: turn sb_eat_lsm_opts() into a method
nfs_remount(): don't leak, don't ignore LSM options quietly
btrfs: sanitize security_mnt_opts use
selinux; don't open-code a loop in sb_finish_set_opts()
LSM: split ->sb_set_mnt_opts() out of ->sb_kern_mount()
new helper: security_sb_eat_lsm_opts()
...
Linus Torvalds [Sat, 5 Jan 2019 21:18:59 +0000 (13:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull trivial vfs updates from Al Viro:
"A few cleanups + Neil's namespace_unlock() optimization"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
exec: make prepare_bprm_creds static
genheaders: %-<width>s had been there since v6; %-*s - since v7
VFS: use synchronize_rcu_expedited() in namespace_unlock()
iov_iter: reduce code duplication
Linus Torvalds [Sat, 5 Jan 2019 20:48:25 +0000 (12:48 -0800)]
Merge tag 'mips_fixes_4.21_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few early MIPS fixes for 4.21:
- The Broadcom BCM63xx platform sees a fix for resetting the BCM6368
ethernet switch, and the removal of a platform device we've never
had a driver for.
- The Alchemy platform sees a few fixes for bitrot that occurred
within the past few cycles.
- We now enable vectored interrupt support for the MediaTek MT7620
SoC, which makes sense since they're supported by the SoC but in
this case also works around a bug relating to the location of
exception vectors when using a recent version of U-Boot.
- The atomic64_fetch_*_relaxed() family of functions see a fix for a
regression in MIPS64 kernels since v4.19.
- Cavium Octeon III CN7xxx systems will now disable their RGMII
interfaces rather than attempt to enable them & warn about the lack
of support for doing so, as they did since initial CN7xxx ethernet
support was added in v4.7.
- The Microsemi/Microchip MSCC SoCs gain a MAINTAINERS entry.
- .mailmap now provides consistency for Dengcheng Zhu's name &
current email address"
* tag 'mips_fixes_4.21_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: OCTEON: mark RGMII interface disabled on OCTEON III
MIPS: Fix a R10000_LLSC_WAR logic in atomic.h
MIPS: BCM63XX: drop unused and broken DSP platform device
mailmap: Update name spelling and email for Dengcheng Zhu
MIPS: ralink: Select CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8
MAINTAINERS: Add a maintainer for MSCC MIPS SoCs
MIPS: Alchemy: update dma masks for devboard devices
MIPS: Alchemy: update cpu-feature-overrides
MIPS: Alchemy: drop DB1000 IrDA support bits
MIPS: alchemy: cpu_all_mask is forbidden for clock event devices
MIPS: BCM63XX: fix switch core reset on BCM6368
Linus Torvalds [Sat, 5 Jan 2019 19:48:44 +0000 (11:48 -0800)]
Merge tag 'powerpc-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A fix for the recent access_ok() change, which broke the build. We
recently added a use of type in order to squash a warning elsewhere
about type being unused.
A handful of other minor build fixes, and one defconfig update.
Thanks to: Christian Lamparter, Christophe Leroy, Diana Craciun,
Mathieu Malaterre"
* tag 'powerpc-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Drop use of 'type' from access_ok()
KVM: PPC: Book3S HV: radix: Fix uninitialized var build error
powerpc/configs: Add PPC4xx_OCM to ppc40x_defconfig
powerpc/4xx/ocm: Fix phys_addr_t printf warnings
powerpc/4xx/ocm: Fix compilation error due to PAGE_KERNEL usage
powerpc/fsl: Fixed warning: orphan section `__btb_flush_fixup'
Linus Torvalds [Sat, 5 Jan 2019 19:30:37 +0000 (11:30 -0800)]
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
Linus Torvalds [Sat, 5 Jan 2019 19:28:39 +0000 (11:28 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I'm safely chained back up to my desk, so please pull these arm64
fixes for -rc1 that address some issues that cropped up during the
merge window:
- Prevent KASLR from mapping the top page of the virtual address
space
Linus Torvalds [Sat, 5 Jan 2019 19:23:17 +0000 (11:23 -0800)]
Merge tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Included in this update:
- Florian Fainelli noticed that userspace segfaults caused by the
lack of kernel-userspace helpers was hard to diagnose; we now issue
a warning when userspace tries to use the helpers but the kernel
has them disabled.
- Ben Dooks wants compatibility for the old ATAG serial number with
DT systems.
- Some cleanup of assembly by Nicolas Pitre.
- User accessors optimisation from Vincent Whitchurch.
- More robust kdump on SMP systems from Yufen Wang.
- Sebastian Andrzej Siewior noticed problems with the SMP "boot_lock"
on RT kernels, and so we convert the Versatile series of platforms
to use a raw spinlock instead, consolidating the Versatile
implementation. We entirely remove the boot_lock on OMAP systems,
where it's unnecessary. Further patches for other systems will be
submitted for the following merge window.
- Start switching old StrongARM-11x0 systems to use gpiolib rather
than their private GPIO implementation - mostly PCMCIA bits.
- ARM Kconfig cleanups.
- Cleanup a mostly harmless mistake in the recent Spectre patch in
4.20 (which had the effect that data that can be placed into the
init sections was incorrectly always placed in the rodata section)"
* tag 'for-4.21' of git://git.armlinux.org.uk/~rmk/linux-arm: (25 commits)
ARM: omap2: remove unnecessary boot_lock
ARM: versatile: rename and comment SMP implementation
ARM: versatile: convert boot_lock to raw
ARM: vexpress/realview: consolidate immitation CPU hotplug
ARM: fix the cockup in the previous patch
ARM: sa1100/cerf: switch to using gpio_led_register_device()
ARM: sa1100/assabet: switch to using gpio leds
ARM: sa1100/assabet: add gpio keys support for right-hand two buttons
ARM: sa1111: remove legacy GPIO interfaces
pcmcia: sa1100*: remove redundant bvd1/bvd2 setting
ARM: pxa/lubbock: switch PCMCIA to MAX1600 library
ARM: pxa/mainstone: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/neponset: switch PCMCIA to MAX1600 library and gpiod APIs
ARM: sa1100/jornada720: switch PCMCIA to gpiod APIs
pcmcia: add MAX1600 library
ARM: sa1100: explicitly register sa11x0-pcmcia devices
ARM: 8813/1: Make aligned 2-byte getuser()/putuser() atomic on ARMv6+
ARM: 8812/1: Optimise copy_{from/to}_user for !CPU_USE_DOMAINS
ARM: 8811/1: always list both ldrd/strd registers explicitly
ARM: 8808/1: kexec:offline panic_smp_self_stop CPU
...
Linus Torvalds [Sat, 5 Jan 2019 17:50:07 +0000 (09:50 -0800)]
Merge tag 'csky-for-linus-4.21' of git://github.com/c-sky/csky-linux
Pull arch/csky updates from Guo Ren:
"Here are three main features (cpu_hotplug, basic ftrace, basic perf)
and some bugfixes:
Features:
- Add CPU-hotplug support for SMP
- Add ftrace with function trace and function graph trace
- Add Perf support
- Add EM_CSKY_OLD 39
- optimize kernel panic print.
- remove syscall_exit_work
Bugfixes:
- fix abiv2 mmap(... O_SYNC) failure
- fix gdb coredump error
- remove vdsp implement for kernel
- fix qemu failure to bootup sometimes
- fix ftrace call-graph panic
- fix device tree node reference leak
- remove meaningless header-y
- fix save hi,lo,dspcr regs in switch_stack
- remove unused members in processor.h"
* tag 'csky-for-linus-4.21' of git://github.com/c-sky/csky-linux:
csky: Add perf support for C-SKY
csky: Add EM_CSKY_OLD 39
clocksource/drivers/c-sky: fixup ftrace call-graph panic
csky: ftrace call graph supported.
csky: basic ftrace supported
csky: remove unused members in processor.h
csky: optimize kernel panic print.
csky: stacktrace supported.
csky: CPU-hotplug supported for SMP
clocksource/drivers/c-sky: fixup qemu fail to bootup sometimes.
csky: fixup save hi,lo,dspcr regs in switch_stack.
csky: remove syscall_exit_work
csky: fixup remove vdsp implement for kernel.
csky: bugfix gdb coredump error.
csky: fixup abiv2 mmap(... O_SYNC) failed.
csky: define syscall_get_arch()
elf-em.h: add EM_CSKY
csky: remove meaningless header-y
csky: Don't leak device tree node reference
Linus Torvalds [Sat, 5 Jan 2019 17:16:18 +0000 (09:16 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
dma-direct: fix DMA_ATTR_NO_KERNEL_MAPPING for remapped allocations
We need to return a dma_addr_t even if we don't have a kernel mapping.
Do so by consolidating the phys_to_dma call in a single place and jump
to it from all the branches that return successfully.
Fixes: bfd56cd60521 ("dma-mapping: support highmem in the generic remap allocator") Reported-by: Liviu Dudau <liviu@dudau.co.uk Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Liviu Dudau <liviu@dudau.co.uk>
In many cases we don't have to create a GART mapping at all, which
also means there is nothing to unmap. Fix the range check that was
incorrectly modified when removing the mapping_error method.
Fixes: 9e8aa6b546 ("x86/amd_gart: remove the mapping_error dma_map_ops method") Reported-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Michal Kubecek <mkubecek@suse.cz>
Linus Torvalds [Sat, 5 Jan 2019 01:52:49 +0000 (17:52 -0800)]
x86: re-introduce non-generic memcpy_{to,from}io
This has been broken forever, and nobody ever really noticed because
it's purely a performance issue.
Long long ago, in commit 6175ddf06b61 ("x86: Clean up mem*io functions")
Brian Gerst simplified the memory copies to and from iomem, since on
x86, the instructions to access iomem are exactly the same as the
regular instructions.
That is technically true, and things worked, and nobody said anything.
Besides, back then the regular memcpy was pretty simple and worked fine.
Nobody noticed except for David Laight, that is. David has a testing a
TLP monitor he was writing for an FPGA, and has been occasionally
complaining about how memcpy_toio() writes things one byte at a time.
Which is completely unacceptable from a performance standpoint, even if
it happens to technically work.
The reason it's writing one byte at a time is because while it's
technically true that accesses to iomem are the same as accesses to
regular memory on x86, the _granularity_ (and ordering) of accesses
matter to iomem in ways that they don't matter to regular cached memory.
In particular, when ERMS is set, we default to using "rep movsb" for
larger memory copies. That is indeed perfectly fine for real memory,
since the whole point is that the CPU is going to do cacheline
optimizations and executes the memory copy efficiently for cached
memory.
With iomem? Not so much. With iomem, "rep movsb" will indeed work, but
it will copy things one byte at a time. Slowly and ponderously.
Now, originally, back in 2010 when commit 6175ddf06b61 was done, we
didn't use ERMS, and this was much less noticeable.
Our normal memcpy() was simpler in other ways too.
Because in fact, it's not just about using the string instructions. Our
memcpy() these days does things like "read and write overlapping values"
to handle the last bytes of the copy. Again, for normal memory,
overlapping accesses isn't an issue. For iomem? It can be.
So this re-introduces the specialized memcpy_toio(), memcpy_fromio() and
memset_io() functions. It doesn't particularly optimize them, but it
tries to at least not be horrid, or do overlapping accesses. In fact,
this uses the existing __inline_memcpy() function that we still had
lying around that uses our very traditional "rep movsl" loop followed by
movsw/movsb for the final bytes.
Somebody may decide to try to improve on it, but if we've gone almost a
decade with only one person really ever noticing and complaining, maybe
it's not worth worrying about further, once it's not _completely_ broken?
Reported-by: David Laight <David.Laight@aculab.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's just one single store instruction, along with generating an
exception table entry pointing to the Efault label case in case that
instruction faults.
with the exception table generated for that 'mov' instruction causing us
to jump to a stub that set %edx to -EFAULT and then jumped back to the
'testl' instruction.
So not only do we now get rid of the extra code in the normal sequence,
we also avoid unnecessarily keeping that extra error register live
across it all.
Linus Torvalds [Sun, 22 May 2016 04:44:51 +0000 (21:44 -0700)]
x86 uaccess: Introduce __put_user_goto
This is finally the actual reason for the odd error handling in the
"unsafe_get/put_user()" functions, introduced over three years ago.
Using a "jump to error label" interface is somewhat odd, but very
convenient as a programming interface, and more importantly, it fits
very well with simply making the target be the exception handler address
directly from the inline asm.
The reason it took over three years to actually do this? We need "asm
goto" support for it, which only became the default on x86 last year.
It's now been a year that we've forced asm goto support (see commit e501ce957a78 "x86: Force asm-goto"), and so let's just do it here too.
[ Side note: this commit was originally done back in 2016. The above
commentary about timing is obviously about it only now getting merged
into my real upstream tree - Linus ]
Sadly, gcc still only supports "asm goto" with asms that do not have any
outputs, so we are limited to only the put_user case for this. Maybe in
several more years we can do the get_user case too.
Helge Deller [Fri, 4 Jan 2019 22:32:53 +0000 (23:32 +0100)]
parisc: Remap hugepage-aligned pages in set_kernel_text_rw()
The alternative coding patch for parisc in kernel 4.20 broke booting
machines with PA8500-PA8700 CPUs. The problem is, that for such machines
the parisc kernel automatically utilizes huge pages to access kernel
text code, but the set_kernel_text_rw() function, which is used shortly
before applying any alternative patches, didn't used the correctly
hugepage-aligned addresses to remap the kernel text read-writeable.
Jens Axboe [Thu, 3 Jan 2019 23:29:15 +0000 (15:29 -0800)]
mm/page_io.c: fix polled swap page in
swap_readpage() wants to do polling to bring in pages if asked to, but
it doesn't mark the bio as being polled. Additionally, the looping
around the blk_poll() check isn't correct - if we get a zero return, we
should call io_schedule(), we can't just assume that the bio has
completed. The regular bio->bi_private check should be used for that.
Link: http://lkml.kernel.org/r/e15243a8-2cdf-c32c-ecee-f289377c8ef9@kernel.dk Signed-off-by: Jens Axboe <axboe@kernel.dk> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/*
* This memory isn't freed when the device is put,
* I don't have a nice idea for that though. Conceptually
* dma_mask in struct device should not be a pointer.
* See http://thread.gmane.org/gmane.linux.kernel.pci/9081
*/
pdev->dev.dma_mask =
kmalloc(sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
Since this leak has existed for more than 8 years and it does not
reference other parts of the memory, let kmemleak ignore it, so users
don't need to waste time reporting this in the future.
Nikolay Borisov [Thu, 3 Jan 2019 23:29:02 +0000 (15:29 -0800)]
fs: don't open code lru_to_page()
Multiple filesystems open code lru_to_page(). Rectify this by moving
the macro from mm_inline (which is specific to lru stuff) to the more
generic mm.h header and start using the macro where appropriate.
No functional changes.
Link: http://lkml.kernel.org/r/20181129104810.23361-1-nborisov@suse.com Link: https://lkml.kernel.org/r/20181129075301.29087-1-nborisov@suse.com Signed-off-by: Nikolay Borisov <nborisov@suse.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Acked-by: Pankaj gupta <pagupta@redhat.com> Acked-by: "Yan, Zheng" <zyan@redhat.com> [ceph] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Android needs to mremap large regions of memory during memory management
related operations. The mremap system call can be really slow if THP is
not enabled. The bottleneck is move_page_tables, which is copying each
pte at a time, and can be really slow across a large map. Turning on
THP may not be a viable option, and is not for us. This patch speeds up
the performance for non-THP system by copying at the PMD level when
possible.
The speedup is an order of magnitude on x86 (~20x). On a 1GB mremap,
the mremap completion times drops from 3.4-3.6 milliseconds to 144-160
microseconds.
Before:
Total mremap time for 1GB data: 3521942 nanoseconds.
Total mremap time for 1GB data: 3449229 nanoseconds.
Total mremap time for 1GB data: 3488230 nanoseconds.
After:
Total mremap time for 1GB data: 150279 nanoseconds.
Total mremap time for 1GB data: 144665 nanoseconds.
Total mremap time for 1GB data: 158708 nanoseconds.
If THP is enabled the optimization is mostly skipped except in certain
situations.
[joel@joelfernandes.org: fix 'move_normal_pmd' unused function warning] Link: http://lkml.kernel.org/r/20181108224457.GB209347@google.com Link: http://lkml.kernel.org/r/20181108181201.88826-3-joelaf@google.com Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Acked-by: Kirill A. Shutemov <kirill@shutemov.name> Reviewed-by: William Kucharski <william.kucharski@oracle.com> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Cc: Michal Hocko <mhocko@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: treewide: remove unused address argument from pte_alloc functions
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
David Engraf [Thu, 3 Jan 2019 23:28:31 +0000 (15:28 -0800)]
initramfs: cleanup incomplete rootfs
Unpacking an external initrd may fail e.g. not enough memory. This
leads to an incomplete rootfs because some files might be extracted
already. Fixed by cleaning the rootfs so the kernel is not using an
incomplete rootfs.
Link: http://lkml.kernel.org/r/20181030151805.5519-1-david.engraf@sysgo.com Signed-off-by: David Engraf <david.engraf@sysgo.com> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Du Changbin [Thu, 3 Jan 2019 23:28:27 +0000 (15:28 -0800)]
scripts/gdb: fix lx-version string output
A bug is present in GDB which causes early string termination when
parsing variables. This has been reported [0], but we should ensure
that we can support at least basic printing of the core kernel strings.
For current gdb version (has been tested with 7.3 and 8.1), 'lx-version'
only prints one character.
(gdb) lx-version
L(gdb)
This can be fixed by casting 'linux_banner' as (char *).
(gdb) lx-version
Linux version 4.19.0-rc1+ (changbin@acer) (gcc version 7.3.0 (Ubuntu 7.3.0-16ubuntu3)) #21 SMP Sat Sep 1 21:43:30 CST 2018
Anders Roxell [Thu, 3 Jan 2019 23:28:24 +0000 (15:28 -0800)]
kernel/kcov.c: mark write_comp_data() as notrace
Since __sanitizer_cov_trace_const_cmp4 is marked as notrace, the
function called from __sanitizer_cov_trace_const_cmp4 shouldn't be
traceable either. ftrace_graph_caller() gets called every time func
write_comp_data() gets called if it isn't marked 'notrace'. This is the
backtrace from gdb:
#0 ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:179
#1 0xffffff8010201920 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:151
#2 0xffffff8010439714 in write_comp_data (type=5, arg1=0, arg2=0, ip=18446743524224276596) at ../kernel/kcov.c:116
#3 0xffffff8010439894 in __sanitizer_cov_trace_const_cmp4 (arg1=<optimized out>, arg2=<optimized out>) at ../kernel/kcov.c:188
#4 0xffffff8010201874 in prepare_ftrace_return (self_addr=18446743524226602768, parent=0xffffff801014b918, frame_pointer=18446743524223531344) at ./include/generated/atomic-instrumented.h:27
#5 0xffffff801020194c in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:182
Rework so that write_comp_data() that are called from
__sanitizer_cov_trace_*_cmp*() are marked as 'notrace'.
Commit 903e8ff86753 ("kernel/kcov.c: mark funcs in __sanitizer_cov_trace_pc() as notrace")
missed to mark write_comp_data() as 'notrace'. When that patch was
created gcc-7 was used. In lib/Kconfig.debug
config KCOV_ENABLE_COMPARISONS
depends on $(cc-option,-fsanitize-coverage=trace-cmp)
That code path isn't hit with gcc-7. However, it were that with gcc-8.
Link: http://lkml.kernel.org/r/20181206143011.23719-1-anders.roxell@linaro.org Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Co-developed-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Feng Tang [Thu, 3 Jan 2019 23:28:17 +0000 (15:28 -0800)]
panic: add options to print system info when panic happens
Kernel panic issues are always painful to debug, partially because it's
not easy to get enough information of the context when panic happens.
And we have ramoops and kdump for that, while this commit tries to
provide a easier way to show the system info by adding a cmdline
parameter, referring some idea from sysrq handler.
Link: http://lkml.kernel.org/r/1543398842-19295-2-git-send-email-feng.tang@intel.com Signed-off-by: Feng Tang <feng.tang@intel.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tigran Aivazian [Thu, 3 Jan 2019 23:28:14 +0000 (15:28 -0800)]
bfs: extra sanity checking and static inode bitmap
Strengthen validation of BFS superblock against corruption. Make
in-core inode bitmap static part of superblock info structure. Print a
warning when mounting a BFS filesystem created with "-N 512" option as
only 510 files can be created in the root directory. Make the kernel
messages more uniform. Update the 'prefix' passed to bfs_dump_imap() to
match the current naming of operations. White space and comments
cleanup.
Oleg Nesterov [Thu, 3 Jan 2019 23:28:11 +0000 (15:28 -0800)]
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
get_arg_page() checks bprm->rlim_stack.rlim_cur and re-calculates the
"extra" size for argv/envp pointers every time, this is a bit ugly and
even not strictly correct: acct_arg_size() must not account this size.
Remove all the rlimit code in get_arg_page(). Instead, add bprm->argmin
calculated once at the start of __do_execve_file() and change
copy_strings to check bprm->p >= bprm->argmin.
The patch adds the new helper, prepare_arg_pages() which initializes
bprm->argc/envc and bprm->argmin.
[oleg@redhat.com: fix !CONFIG_MMU version of get_arg_page()] Link: http://lkml.kernel.org/r/20181126122307.GA1660@redhat.com
[akpm@linux-foundation.org: use max_t] Link: http://lkml.kernel.org/r/20181112160910.GA28440@redhat.com Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
load_script() simply truncates bprm->buf and this is very wrong if the
length of shebang string exceeds BINPRM_BUF_SIZE-2. This can silently
truncate i_arg or (worse) we can execute the wrong binary if buf[2:126]
happens to be the valid executable path.
Change load_script() to return ENOEXEC if it can't find '\n' or zero in
bprm->buf. Note that '\0' can come from either
prepare_binprm()->memset() or from kernel_read(), we do not care.
Link: http://lkml.kernel.org/r/20181112160931.GA28463@redhat.com Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Ben Woodard <woodard@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yi Wang [Thu, 3 Jan 2019 23:28:03 +0000 (15:28 -0800)]
fork: fix some -Wmissing-prototypes warnings
We get a warning when building kernel with W=1:
kernel/fork.c:167:13: warning: no previous prototype for `arch_release_thread_stack' [-Wmissing-prototypes]
kernel/fork.c:779:13: warning: no previous prototype for `fork_init' [-Wmissing-prototypes]
Add the missing declaration in head file to fix this.
Also, remove arch_release_thread_stack() completely because no arch
seems to implement it since bb9d81264 (arch: remove tile port).
Link: http://lkml.kernel.org/r/1542170087-23645-1-git-send-email-wang.yi59@zte.com.cn Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carmeli Tamir [Thu, 3 Jan 2019 23:28:00 +0000 (15:28 -0800)]
fat: new inline functions to determine the FAT variant (32, 16 or 12)
This patch introduces 3 new inline functions - is_fat12, is_fat16 and
is_fat32, and replaces every occurrence in the code in which the FS
variant (whether this is FAT12, FAT16 or FAT32) was previously checked
using msdos_sb_info->fat_bits.
Link: http://lkml.kernel.org/r/1544990640-11604-4-git-send-email-carmeli.tamir@gmail.com Signed-off-by: Carmeli Tamir <carmeli.tamir@gmail.com> Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carmeli Tamir [Thu, 3 Jan 2019 23:27:56 +0000 (15:27 -0800)]
fat: move MAX_FAT to fat.h and change it to inline function
MAX_FAT is useless in msdos_fs.h, since it uses the MSDOS_SB function
that is defined in fat.h. So really, this macro can be only called from
code that already includes fat.h.
Hence, this patch moves it to fat.h, right after MSDOS_SB is defined. I
also changed it to an inline function in order to save the double call
to MSDOS_SB. This was suggested by joe@perches.com in the previous
version.
This patch is required for the next in the series, in which the variant
(whether this is FAT12, FAT16 or FAT32) checks are replaced with new
macros.
Link: http://lkml.kernel.org/r/1544990640-11604-3-git-send-email-carmeli.tamir@gmail.com Signed-off-by: Carmeli Tamir <carmeli.tamir@gmail.com> Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carmeli Tamir [Thu, 3 Jan 2019 23:27:53 +0000 (15:27 -0800)]
fat: remove FAT_FIRST_ENT macro
The comment edited in this patch was the only reference to the
FAT_FIRST_ENT macro, which is not used anymore. Moreover, the commented
line of code does not compile with the current code.
Since the FAT_FIRST_ENT macro checks the FAT variant in a way that the
patch series changes, I removed it, and instead wrote a clear
explanation of what was checked.
I verified that the changed comment is correct according to Microsoft
FAT spec, search for "BPB_Media" in the following references:
1. Microsoft FAT specification 2005
(http://read.pudn.com/downloads77/ebook/294884/FAT32%20Spec%20%28SDA%20Contribution%29.pdf).
Search for 'volume label'.
2. Microsoft Extensible Firmware Initiative, FAT32 File System Specification
(https://staff.washington.edu/dittrich/misc/fatgen103.pdf).
Search for 'volume label'.
Link: http://lkml.kernel.org/r/1544990640-11604-2-git-send-email-carmeli.tamir@gmail.com Signed-off-by: Carmeli Tamir <carmeli.tamir@gmail.com> Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carmeli Tamir [Thu, 3 Jan 2019 23:27:49 +0000 (15:27 -0800)]
include/uapi/linux/msdos_fs.h: use MSDOS_NAME for volume label size
The FAT file system volume label file stored in the root directory
should match the volume label field in the FAT boot sector. As
consequence, the max length of these fields ought to be the same. This
patch replaces the magic '11' usef in the struct fat_boot_sector with
MSDOS_NAME, which is used in struct msdos_dir_entry.
Please check the following references:
1. Microsoft FAT specification 2005
(http://read.pudn.com/downloads77/ebook/294884/FAT32%20Spec%20%28SDA%20Contribution%29.pdf).
Search for 'volume label'.
2. Microsoft Extensible Firmware Initiative, FAT32 File System Specification
(https://staff.washington.edu/dittrich/misc/fatgen103.pdf).
Search for 'volume label'.
3. User space code that creates FAT filesystem
sometimes uses MSDOS_NAME for the label, sometimes not.
Search for 'if (memcmp(label, NO_NAME, MSDOS_NAME))'.
I consider to make the same patch there as well.
https://github.com/dosfstools/dosfstools/blob/master/src/mkfs.fat.c
Link: http://lkml.kernel.org/r/1543096879-82837-1-git-send-email-carmeli.tamir@gmail.com Signed-off-by: Carmeli Tamir <carmeli.tamir@gmail.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: Jens Axboe <axboe@kernel.dk> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The immutable, append-only and no-dump attributes can only be retrieved
with an ioctl; implement the ->getattr() method to return them on statx.
Do not return the inode birthtime yet, because the issue of how best to
handle the post-2038 timestamps is still under discussion.
This patch is needed to pass xfstests generic/424.
Link: http://lkml.kernel.org/r/20181014163558.sxorxlzjqccq2lpw@eaf Signed-off-by: Ernesto A. Fernández <ernesto.mnd.fernandez@gmail.com> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Thu, 3 Jan 2019 23:27:43 +0000 (15:27 -0800)]
autofs: add strictexpire mount option
Commit 092a53452bb7 ("autofs: take more care to not update last_used on
path walk") helped to (partially) resolve a problem where automounts
were not expiring due to aggressive accesses from user space.
This patch was later reverted because, for very large environments, it
meant more mount requests from clients and when there are a lot of
clients this caused a fairly significant increase in server load.
But there is a need for both types of expire check, depending on use
case, so add a mount option to allow for strict update of last use of
autofs dentrys (which just means not updating the last use on path walk
access).
projects / mirror_ubuntu-hirsute-kernel.git / log