USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jon Mason <jon.mason@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.
I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:
==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address: ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
>ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Michael Ellerman [Thu, 22 Jun 2017 06:52:51 +0000 (16:52 +1000)]
powerpc/slb: Force a full SLB flush when we insert for a bad EA
BugLink: http://bugs.launchpad.net/bugs/1702118
[Note this patch is not upstream. The bug fix was fixed differently in
upstream prior to the bug being identified.]
The SLB miss handler calls slb_allocate_realmode() in order to create an
SLB entry for the faulting address. At the very start of that function
we check that the faulting Effective Address (EA) is less than
PGTABLE_RANGE (ignoring the region), ie. is it an address which could
possibly fit in the virtual address space.
For an EA which fails that test, we branch out of line (to label 8), but
we still go on to create an SLB entry for the address. The SLB entry we
create has a VSID of 0, which means it will never match anything in the
hash table and so can't actually translate to a physical address.
However that SLB entry will be inserted in the SLB, and so needs to be
managed properly like any other SLB entry. In particular we need to
insert the SLB entry in the SLB cache, so that it will be flushed when
the process is descheduled.
And that is where the bugs begin. The first bug is that slb_finish_load()
uses cr7 to decide if it should insert the SLB entry into the SLB cache.
When we come from the invalid EA case we don't set cr7, it just has some
junk value from userspace. So we may or may not insert the SLB entry in
the SLB cache. If we fail to insert it, we may then incorrectly leave it
in the SLB when the process is descheduled.
The second bug is that even if we do happen to add the entry to the SLB
cache, we do not have enough bits in the SLB cache to remember the full
ESID value for very large EAs.
For example if a process branches to 0x788c545a18000000, that results in
a 256MB SLB entry with an ESID of 0x788c545a1. But each entry in the SLB
cache is only 32-bits, meaning we truncate the ESID to 0x88c545a1. This
has the same effect as the first bug, we incorrectly leave the SLB entry
in the SLB when the process is descheduled.
When a process accesses an invalid EA it results in a SEGV signal being
sent to the process, which typically results in the process being
killed. Process death isn't instantaneous however, the process may catch
the SEGV signal and continue somehow, or the kernel may start writing a
core dump for the process, either of which means it's possible for the
process to be preempted while its processing the SEGV but before it's
been killed.
If that happens, when the process is scheduled back onto the CPU we will
allocate a new SLB entry for the NIP, which will insert a second entry
into the SLB for the bad EA. Because we never flushed the original
entry, due to either bug one or two, we now have two SLB entries that
match the same EA.
If another access is made to that EA, either by the process continuing
after catching the SEGV, or by a second process accessing the same bad
EA on the same CPU, we will trigger an SLB multi-hit machine check
exception. This has been observed happening in the wild.
The fix is when we hit the invalid EA case, we mark the SLB cache as
being full. This causes us to not insert the truncated ESID into the SLB
cache, and means when the process is switched out we will flush the
entire SLB. Note that this works both for the original fault and for a
subsequent call to slb_allocate_realmode() from switch_slb().
Because we mark the SLB cache as full, it doesn't really matter what
value is in cr7, but rather than leaving it as something random we set
it to indicate the address was a kernel address. That also skips the
attempt to insert it in the SLB cache which is a nice side effect.
Another way to fix the bug would be to make the entries in the SLB cache
wider, so that we don't truncate the ESID. However this would be a more
intrusive change as it alters the size and layout of the paca.
This bug was fixed in upstream by commit f0f558b131db ("powerpc/mm:
Preserve CFAR value on SLB miss caused by access to bogus address"),
which changed the way we handle a bad EA entirely removing this bug in
the process.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
With the S25FL127S nor flash part, each writing to the configuration
register takes hundreds of ms. During that time, no more accesses to
the flash should be done (even reads).
This commit adds a wait loop after the register writing until the flash
finishes its work.
This issue could make rootfs mounting fail when the latter was done too
much closely to this quad enable bit setting step. And in this case, a
driver as UBIFS may try to recover the filesystem and may broke it
completely.
Signed-off-by: Joël Esponde <joel.esponde@honeywell.com> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
An empty __dtb_start to __dtb_end section might result in
initial_boot_params being null for arch/mips/ralink. This showed that the
boot process hangs indefinitely in of_scan_flat_dt().
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14605/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When a kerberos 5 ticket is being decoded so that it can be loaded into an
rxrpc-type key, there are several places in which the length of a
variable-length field is checked to make sure that it's not going to
overrun the available data - but the data is padded to the nearest
four-byte boundary and the code doesn't check for this extra. This could
lead to the size-remaining variable wrapping and the data pointer going
over the end of the buffer.
Fix this by making the various variable-length data checks use the padded
length.
Reported-by: 石磊 <shilei-c@360.cn> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.c.dionne@auristor.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Fix up the root-hub descriptor to accommodate the variable-length
DeviceRemovable and PortPwrCtrlMask fields, while marking all ports as
removable (and leaving the reserved bit zero unset).
Also add a build-time constraint on VHCI_HC_PORTS which must never be
greater than USB_MAXCHILDREN (but this was only enforced through a
KConfig constant).
This specifically fixes the descriptor layout whenever VHCI_HC_PORTS is
greater than seven (default is 8).
Fixes: 04679b3489e0 ("Staging: USB/IP: add client driver") Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net> Cc: Valentina Manea <valentina.manea.m@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
[ johan: backport to v4.4, which uses VHCI_NPORTS ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Increase the default display clock on newer asics to
accomodate some high res modes with really high refresh
rates.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=93826 Acked-by: Chunming Zhou <david1.zhou@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
We were using the wrong structure which lead to an overflow
on some boards.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=101387 Acked-by: Chunming Zhou <david1.zhou@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
bug: https://bugs.freedesktop.org/show_bug.cgi?id=101491 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When iscsi WRITE underflow occurs there are two different scenarios
that can happen.
Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH
underflow is detected, the iscsi immediate data payload is the
smaller SCSI CDB TRANSFER LENGTH.
That is, when a host fabric LLD is using a fixed size EDTL for
a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual
SCSI payload ends up being smaller than EDTL. In iscsi, this
means the received iscsi immediate data payload matches the
smaller SCSI CDB TRANSFER LENGTH, because there is no more
SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH.
However, it's possible for a malicous host to send a WRITE
underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH,
but incoming iscsi immediate data actually matches EDTL.
In the wild, we've never had a iscsi host environment actually
try to do this.
For this special case, it's wrong to truncate part of the
control CDB payload and continue to process the command during
underflow when immediate data payload received was larger than
SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the
bogus payload as a defensive action.
Note this potential bug was originally relaxed by the following
for allowing WRITE underflow in MSFT FCP host environments:
target: allow underflow/overflow for PR OUT etc. commands
Cc: Roland Dreier <roland@purestorage.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED
when a fabric driver drops it's second reference from below the
target_core_tmr.c based callers of transport_cmd_finish_abort().
Recently with the conversion of kref to refcount_t, this bug was
manifesting itself as:
[705519.601034] refcount_t: underflow; use-after-free.
[705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs
[705539.719111] ------------[ cut here ]------------
[705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51
Since the original kref atomic_t based kref_put() didn't check for
underflow and only invoked the final callback when zero was reached,
this bug did not manifest in practice since all se_cmd memory is
using preallocated tags.
To address this, go ahead and propigate the existing return from
transport_put_cmd() up via transport_cmd_finish_abort(), and
change transport_cmd_finish_abort() + core_tmr_handle_tas_abort()
callers to only do their local target_put_sess_cmd() if necessary.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Tested-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Himanshu Madhani <himanshu.madhani@qlogic.com> Cc: Sagi Grimberg <sagig@mellanox.com> Tested-by: Gary Guo <ghg@datera.io> Tested-by: Chu Yuan Lin <cyl@datera.io> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This is called from the core timekeeping code via:
cycle_now = tkr->read(tkr->clock);
tkr->read is the cached tkr->clock->read() function pointer.
When the clocksource is changed then tkr->clock and tkr->read
are updated sequentially. The code above results in a sequential
load operation of tkr->read and tkr->clock as well.
If the store to tkr->clock hits between the loads of tkr->read
and tkr->clock, then the old read() function is called with the
new clock pointer. As a consequence the read() function
dereferences a different data structure and the resulting 'reg'
pointer can point anywhere including NULL.
This problem was introduced when the timekeeping code was
switched over to use struct tk_read_base. Before that, it was
theoretically possible as well when the compiler decided to
reload clock in the code sequence:
now = tk->clock->read(tk->clock);
Add a helper function which avoids the issue by reading
tk_read_base->clock once into a local variable clk and then issue
the read function via clk->read(clk). This guarantees that the
read() function always gets the proper clocksource pointer handed
in.
Since there is now no use for the tkr.read pointer, this patch
also removes it, and to address stopping the fast timekeeper
during suspend/resume, it introduces a dummy clocksource to use
rather then just a dummy read function.
Signed-off-by: John Stultz <john.stultz@linaro.org> Acked-by: Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Daniel Mentz <danielmentz@google.com> Link: http://lkml.kernel.org/r/1496965462-20003-2-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This fixes a crash when function_graph and jprobes are used together.
This is essentially commit 237d28db036e ("ftrace/jprobes/x86: Fix
conflict between jprobes and function graph tracing"), but for powerpc.
Jprobes breaks function_graph tracing since the jprobe hook needs to use
jprobe_return(), which never returns back to the hook, but instead to
the original jprobe'd function. The solution is to momentarily pause
function_graph tracing before invoking the jprobe hook and re-enable it
when returning back to the original jprobe'd function.
Fixes: 6794c78243bf ("powerpc64: port of the function graph tracer") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Thomas Gleixner wrote:
> The CRIU support added a 'feature' which allows a user space task to send
> arbitrary (kernel) signals to itself. The changelog says:
>
> The kernel prevents sending of siginfo with positive si_code, because
> these codes are reserved for kernel. I think we can allow a task to
> send such a siginfo to itself. This operation should not be dangerous.
>
> Quite contrary to that claim, it turns out that it is outright dangerous
> for signals with info->si_code == SI_TIMER. The following code sequence in
> a user space task allows to crash the kernel:
>
> id = timer_create(CLOCK_XXX, ..... signo = SIGX);
> timer_set(id, ....);
> info->si_signo = SIGX;
> info->si_code = SI_TIMER:
> info->_sifields._timer._tid = id;
> info->_sifields._timer._sys_private = 2;
> rt_[tg]sigqueueinfo(..., SIGX, info);
> sigemptyset(&sigset);
> sigaddset(&sigset, SIGX);
> rt_sigtimedwait(sigset, info);
>
> For timers based on CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID this
> results in a kernel crash because sigwait() dequeues the signal and the
> dequeue code observes:
>
> info->si_code == SI_TIMER && info->_sifields._timer._sys_private != 0
>
> which triggers the following callchain:
>
> do_schedule_next_timer() -> posix_cpu_timer_schedule() -> arm_timer()
>
> arm_timer() executes a list_add() on the timer, which is already armed via
> the timer_set() syscall. That's a double list add which corrupts the posix
> cpu timer list. As a consequence the kernel crashes on the next operation
> touching the posix cpu timer list.
>
> Posix clocks which are internally implemented based on hrtimers are not
> affected by this because hrtimer_start() can handle already armed timers
> nicely, but it's a reliable way to trigger the WARN_ON() in
> hrtimer_forward(), which complains about calling that function on an
> already armed timer.
This problem has existed since the posix timer code was merged into
2.5.63. A few releases earlier in 2.5.60 ptrace gained the ability to
inject not just a signal (which linux has supported since 1.0) but the
full siginfo of a signal.
The core problem is that the code will reschedule in response to
signals getting dequeued not just for signals the timers sent but
for other signals that happen to a si_code of SI_TIMER.
Avoid this confusion by testing to see if the queued signal was
preallocated as all timer signals are preallocated, and so far
only the timer code preallocates signals.
Move the check for if a timer needs to be rescheduled up into
collect_signal where the preallocation check must be performed,
and pass the result back to dequeue_signal where the code reschedules
timers. This makes it clear why the code cares about preallocated
timers.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Reference: 66dd34ad31e5 ("signal: allow to send any siginfo to itself")
Reference: 1669ce53e2ff ("Add PTRACE_GETSIGINFO and PTRACE_SETSIGINFO") Fixes: db8b50ba75f2 ("[PATCH] POSIX clocks & timers") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Downgrade the loglevel for SMB2 to prevent filling the log
with messages if e.g. readdir was interrupted. Also make SMB2
and SMB1 codepaths do the same logging during readdir.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values. To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task. If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.
If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash. To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.
Fixes: b005255e12a3 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When using get_options() it's possible to specify a range of numbers,
like 1-100500. The problem is that it doesn't track array size while
calling internally to get_range() which iterates over the range and
fills the memory with numbers.
Link: http://lkml.kernel.org/r/2613C75C-B04D-4BFF-82A6-12F97BA0F620@gmail.com Signed-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When limiting the argv/envp strings during exec to 1/4 of the stack limit,
the storage of the pointers to the strings was not included. This means
that an exec with huge numbers of tiny strings could eat 1/4 of the stack
limit in strings and then additional space would be later used by the
pointers to the strings.
For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721
single-byte strings would consume less than 2MB of stack, the max (8MB /
4) amount allowed, but the pointers to the strings would consume the
remaining additional stack space (1677721 * 4 == 6710884).
The result (1677721 + 6710884 == 8388605) would exhaust stack space
entirely. Controlling this stack exhaustion could result in
pathological behavior in setuid binaries (CVE-2017-1000365).
[akpm@linux-foundation.org: additional commenting from Kees] Fixes: b6a2fea39318 ("mm: variable length argument support") Link: http://lkml.kernel.org/r/20170622001720.GA32173@beast Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qualys Security Advisory <qsa@qualys.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1702104 Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The alarmtimer code has another source of potentially rearming itself too
fast. Interval timers with a very samll interval have a similar CPU hog
effect as the previously fixed overflow issue.
The reason is that alarmtimers do not implement the normal protection
against this kind of problem which the other posix timer use:
timer expires -> queue signal -> deliver signal -> rearm timer
This scheme brings the rearming under scheduler control and prevents
permanently firing timers which hog the CPU.
Bringing this scheme to the alarm timer code is a major overhaul because it
lacks all the necessary mechanisms completely.
So for a quick fix limit the interval to one jiffie. This is not
problematic in practice as alarmtimers are usually backed by an RTC for
suspend which have 1 second resolution. It could be therefor argued that
the resolution of this clock should be set to 1 second in general, but
that's outside the scope of this fix.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kostya Serebryany <kcc@google.com> Cc: syzkaller <syzkaller@googlegroups.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dmitry Vyukov <dvyukov@google.com> Link: http://lkml.kernel.org/r/20170530211655.896767100@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The code handling the pop76 opcode (ie. bnezc & jialc instructions) in
__compute_return_epc_for_insn() needs to set the value of $31 in the
jialc case, which is encoded with rs = 0. However its check to
differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately
backwards, meaning that if we emulate a bnezc instruction we clobber $31
& if we emulate a jialc instruction it actually behaves like a jic
instruction.
Fix this by inverting the check of rs to match the way the instructions
are actually encoded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 28d6f93d201d ("MIPS: Emulate the new MIPS R6 BNEZC and JIALC instructions") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16178/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Andrey reported a alartimer related RCU stall while fuzzing the kernel with
syzkaller.
The reason for this is an overflow in ktime_add() which brings the
resulting time into negative space and causes immediate expiry of the
timer. The following rearm with a small interval does not bring the timer
back into positive space due to the same issue.
This results in a permanent firing alarmtimer which hogs the CPU.
Use ktime_add_safe() instead which detects the overflow and clamps the
result to KTIME_SEC_MAX.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kostya Serebryany <kcc@google.com> Cc: syzkaller <syzkaller@googlegroups.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dmitry Vyukov <dvyukov@google.com> Link: http://lkml.kernel.org/r/20170530211655.802921648@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
memory_failure() chooses a recovery action function based on the page
flags. For huge pages it uses the tail page flags which don't have
anything interesting set, resulting in:
> Memory failure: 0x9be3b4: Unknown page state
> Memory failure: 0x9be3b4: recovery action for unknown page: Failed
Instead, save a copy of the head page's flags if this is a huge page,
this means if there are no relevant flags for this tail page, we use the
head pages flags instead. This results in the me_huge_page() recovery
action being called:
> Memory failure: 0x9b7969: recovery action for huge page: Delayed
For hugepages that have not yet been allocated, this allows the hugepage
to be dequeued.
Fixes: 524fca1e7356 ("HWPOISON: fix misjudgement of page_action() for errors on mlocked pages") Link: http://lkml.kernel.org/r/20170524130204.21845-1-james.morse@arm.com Signed-off-by: James Morse <james.morse@arm.com> Tested-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Punit Agrawal <punit.agrawal@arm.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Using the syzkaller kernel fuzzer, Andrey Konovalov generated the
following error in gadgetfs:
> BUG: KASAN: use-after-free in __lock_acquire+0x3069/0x3690
> kernel/locking/lockdep.c:3246
> Read of size 8 at addr ffff88003a2bdaf8 by task kworker/3:1/903
>
> CPU: 3 PID: 903 Comm: kworker/3:1 Not tainted 4.12.0-rc4+ #35
> Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
> Workqueue: usb_hub_wq hub_event
> Call Trace:
> __dump_stack lib/dump_stack.c:16 [inline]
> dump_stack+0x292/0x395 lib/dump_stack.c:52
> print_address_description+0x78/0x280 mm/kasan/report.c:252
> kasan_report_error mm/kasan/report.c:351 [inline]
> kasan_report+0x230/0x340 mm/kasan/report.c:408
> __asan_report_load8_noabort+0x19/0x20 mm/kasan/report.c:429
> __lock_acquire+0x3069/0x3690 kernel/locking/lockdep.c:3246
> lock_acquire+0x22d/0x560 kernel/locking/lockdep.c:3855
> __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
> _raw_spin_lock+0x2f/0x40 kernel/locking/spinlock.c:151
> spin_lock include/linux/spinlock.h:299 [inline]
> gadgetfs_suspend+0x89/0x130 drivers/usb/gadget/legacy/inode.c:1682
> set_link_state+0x88e/0xae0 drivers/usb/gadget/udc/dummy_hcd.c:455
> dummy_hub_control+0xd7e/0x1fb0 drivers/usb/gadget/udc/dummy_hcd.c:2074
> rh_call_control drivers/usb/core/hcd.c:689 [inline]
> rh_urb_enqueue drivers/usb/core/hcd.c:846 [inline]
> usb_hcd_submit_urb+0x92f/0x20b0 drivers/usb/core/hcd.c:1650
> usb_submit_urb+0x8b2/0x12c0 drivers/usb/core/urb.c:542
> usb_start_wait_urb+0x148/0x5b0 drivers/usb/core/message.c:56
> usb_internal_control_msg drivers/usb/core/message.c:100 [inline]
> usb_control_msg+0x341/0x4d0 drivers/usb/core/message.c:151
> usb_clear_port_feature+0x74/0xa0 drivers/usb/core/hub.c:412
> hub_port_disable+0x123/0x510 drivers/usb/core/hub.c:4177
> hub_port_init+0x1ed/0x2940 drivers/usb/core/hub.c:4648
> hub_port_connect drivers/usb/core/hub.c:4826 [inline]
> hub_port_connect_change drivers/usb/core/hub.c:4999 [inline]
> port_event drivers/usb/core/hub.c:5105 [inline]
> hub_event+0x1ae1/0x3d40 drivers/usb/core/hub.c:5185
> process_one_work+0xc08/0x1bd0 kernel/workqueue.c:2097
> process_scheduled_works kernel/workqueue.c:2157 [inline]
> worker_thread+0xb2b/0x1860 kernel/workqueue.c:2233
> kthread+0x363/0x440 kernel/kthread.c:231
> ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:424
>
> Allocated by task 9958:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:617
> kmem_cache_alloc_trace+0x87/0x280 mm/slub.c:2745
> kmalloc include/linux/slab.h:492 [inline]
> kzalloc include/linux/slab.h:665 [inline]
> dev_new drivers/usb/gadget/legacy/inode.c:170 [inline]
> gadgetfs_fill_super+0x24f/0x540 drivers/usb/gadget/legacy/inode.c:1993
> mount_single+0xf6/0x160 fs/super.c:1192
> gadgetfs_mount+0x31/0x40 drivers/usb/gadget/legacy/inode.c:2019
> mount_fs+0x9c/0x2d0 fs/super.c:1223
> vfs_kern_mount.part.25+0xcb/0x490 fs/namespace.c:976
> vfs_kern_mount fs/namespace.c:2509 [inline]
> do_new_mount fs/namespace.c:2512 [inline]
> do_mount+0x41b/0x2d90 fs/namespace.c:2834
> SYSC_mount fs/namespace.c:3050 [inline]
> SyS_mount+0xb0/0x120 fs/namespace.c:3027
> entry_SYSCALL_64_fastpath+0x1f/0xbe
>
> Freed by task 9960:
> save_stack_trace+0x1b/0x20 arch/x86/kernel/stacktrace.c:59
> save_stack+0x43/0xd0 mm/kasan/kasan.c:513
> set_track mm/kasan/kasan.c:525 [inline]
> kasan_slab_free+0x72/0xc0 mm/kasan/kasan.c:590
> slab_free_hook mm/slub.c:1357 [inline]
> slab_free_freelist_hook mm/slub.c:1379 [inline]
> slab_free mm/slub.c:2961 [inline]
> kfree+0xed/0x2b0 mm/slub.c:3882
> put_dev+0x124/0x160 drivers/usb/gadget/legacy/inode.c:163
> gadgetfs_kill_sb+0x33/0x60 drivers/usb/gadget/legacy/inode.c:2027
> deactivate_locked_super+0x8d/0xd0 fs/super.c:309
> deactivate_super+0x21e/0x310 fs/super.c:340
> cleanup_mnt+0xb7/0x150 fs/namespace.c:1112
> __cleanup_mnt+0x1b/0x20 fs/namespace.c:1119
> task_work_run+0x1a0/0x280 kernel/task_work.c:116
> exit_task_work include/linux/task_work.h:21 [inline]
> do_exit+0x18a8/0x2820 kernel/exit.c:878
> do_group_exit+0x14e/0x420 kernel/exit.c:982
> get_signal+0x784/0x1780 kernel/signal.c:2318
> do_signal+0xd7/0x2130 arch/x86/kernel/signal.c:808
> exit_to_usermode_loop+0x1ac/0x240 arch/x86/entry/common.c:157
> prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
> syscall_return_slowpath+0x3ba/0x410 arch/x86/entry/common.c:263
> entry_SYSCALL_64_fastpath+0xbc/0xbe
>
> The buggy address belongs to the object at ffff88003a2bdae0
> which belongs to the cache kmalloc-1024 of size 1024
> The buggy address is located 24 bytes inside of
> 1024-byte region [ffff88003a2bdae0, ffff88003a2bdee0)
> The buggy address belongs to the page:
> page:ffffea0000e8ae00 count:1 mapcount:0 mapping: (null)
> index:0x0 compound_mapcount: 0
> flags: 0x100000000008100(slab|head)
> raw: 0100000000008100000000000000000000000000000000000000000100170017
> raw: ffffea0000ed3020ffffea0000f5f820ffff88003e80efc00000000000000000
> page dumped because: kasan: bad access detected
>
> Memory state around the buggy address:
> ffff88003a2bd980: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff88003a2bda00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> >ffff88003a2bda80: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fb
> ^
> ffff88003a2bdb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff88003a2bdb80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ==================================================================
What this means is that the gadgetfs_suspend() routine was trying to
access dev->lock after it had been deallocated. The root cause is a
race in the dummy_hcd driver; the dummy_udc_stop() routine can race
with the rest of the driver because it contains no locking. And even
when proper locking is added, it can still race with the
set_link_state() function because that function incorrectly drops the
private spinlock before invoking any gadget driver callbacks.
The result of this race, as seen above, is that set_link_state() can
invoke a callback in gadgetfs even after gadgetfs has been unbound
from dummy_hcd's UDC and its private data structures have been
deallocated.
include/linux/usb/gadget.h documents that the ->reset, ->disconnect,
->suspend, and ->resume callbacks may be invoked in interrupt context.
In general this is necessary, to prevent races with gadget driver
removal. This patch fixes dummy_hcd to retain the spinlock across
these calls, and it adds a spinlock acquisition to dummy_udc_stop() to
prevent the race.
The net2280 driver makes the same mistake of dropping the private
spinlock for its ->disconnect and ->reset callback invocations. The
patch fixes it too.
Lastly, since gadgetfs_suspend() may be invoked in interrupt context,
it cannot assume that interrupts are enabled when it runs. It must
use spin_lock_irqsave() instead of spin_lock_irq(). The patch fixes
that bug as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When plugging an USB webcam I see the following message:
[106385.615559] xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[106390.583860] handle_tx_event: 913 callbacks suppressed
With this patch applied, I get no more printing of this message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659") Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586db4 ("usb: r8a66597-hcd: host controller driver for R8A6659") Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Flag the first and only port as removable while also leaving the
remaining bits (including the reserved bit zero) unset in accordance
with the specifications:
"Within a byte, if no port exists for a given location, the bit
field representing the port characteristics shall be 0."
Also add a comment marking the legacy PortPwrCtrlMask field.
Fixes: 1cd8fd2887e1 ("usb: gadget: dummy_hcd: add SuperSpeed support") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: Tatyana Brokhman <tlinder@codeaurora.org> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The driver uses a relatively large data structure on the stack, which
showed up on my radar as we get a warning with the "latent entropy"
GCC plugin:
drivers/media/usb/pvrusb2/pvrusb2-eeprom.c:153:1: error: the frame size of 1376 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
The warning is usually hidden as we raise the warning limit to 2048
when the plugin is enabled, but I'd like to lower that again in the
future, and making this function smaller helps to do that without
build regressions.
Further analysis shows that putting an 'i2c_client' structure on
the stack is not really supported, as the embedded 'struct device'
is not initialized here, and we are only saved by the fact that
the function that is called here does not use the pointer at all.
Fixes: d855497edbfb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
According to the datasheet the RCO must be recalibrated
on every power-on-reset. Also remove mutex locking in the
calibration function since callers other than the probe
function (which doesn't need it) will have a lock.
Fixes: 24ddb0e4bba4 ("iio: Add AS3935 lightning sensor support") Cc: George McCollister <george.mccollister@gmail.com> Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
The "len" could be as low as -14 so we should check for negatives.
Fixes: 9a7fe54ddc3a ("staging: r8188eu: Add source files for new driver - part 1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
bit the wrong way. The comments in the code are correct, but the inverted
use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be
enabled instead of disabled unlike what the comments say.
Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can
be only pinged few times before it stops responding.
Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver") Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
'__vmalloc_start_set' currently only gets set in initmem_init() when
!CONFIG_NEED_MULTIPLE_NODES. This breaks detection of vmalloc address
with virt_addr_valid() with CONFIG_NEED_MULTIPLE_NODES=y, causing
a kernel crash:
[mm/usercopy] 517e1fbeb6: kernel BUG at arch/x86/mm/physaddr.c:78!
Set '__vmalloc_start_set' appropriately for that case as well.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Laura Abbott <labbott@redhat.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: dc16ecf7fd1f ("x86-32: use specific __vmalloc_start_set flag in __virt_addr_valid") Link: http://lkml.kernel.org/r/1494278596-30373-1-git-send-email-labbott@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.
Fixes: 3afbd89c9639 ("serial/efm32: add new driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
When VHT IBSS support was added, the size of the extra elements
wasn't considered in ieee80211_ibss_build_presp(), which makes
it possible that it would overrun the allocated buffer. Fix it
by allocating the necessary space.
Fixes: abcff6ef01f9 ("mac80211: add VHT support for IBSS") Reported-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Add the missing IBSS capability flag during capability init as it needs
to be inserted into the generated beacon in order for CSA to work.
Fixes: cd7760e62c2ac ("mac80211: add support for CSA in IBSS mode") Signed-off-by: Piotr Gawlowicz <gawlowicz@tkn.tu-berlin.de> Signed-off-by: Mikołaj Chwalisz <chwalisz@tkn.tu-berlin.de> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Commit 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency
decrease checking) removed the 10 point substraction when comparing the
load against down_threshold but did not remove the related limit for the
down_threshold value. As a result, down_threshold lower than 11 is not
allowed even though values from 1 to 10 do work correctly too. The
comment ("cannot be lower than 11 otherwise freq will not fall") also
does not apply after removing the substraction.
For this reason, allow down_threshold to take any value from 1 to 99
and fix the related comment.
Fixes: 27ed3cd2ebf4 (cpufreq: conservative: Fix the logic in frequency decrease checking) Signed-off-by: Tomasz Wilczyński <twilczynski@naver.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This patch adds the missing kfree() in gs_cmd_reset() to free the
memory that is not used anymore after usb_control_msg().
Cc: Maximilian Schneider <max@schneidersoft.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
This patch closes a long standing race in configfs between
the creation of a new symlink in create_link(), while the
symlink target's config_item is being concurrently removed
via configfs_rmdir().
This can happen because the symlink target's reference
is obtained by config_item_get() in create_link() before
the CONFIGFS_USET_DROPPING bit set by configfs_detach_prep()
during configfs_rmdir() shutdown is actually checked..
This originally manifested itself on ppc64 on v4.8.y under
heavy load using ibmvscsi target ports with Novalink API:
To close this race, go ahead and obtain the symlink's target
config_item reference only after the existing CONFIGFS_USET_DROPPING
check succeeds.
This way, if configfs_rmdir() wins create_link() will return -ENONET,
and if create_link() wins configfs_rmdir() will return -EBUSY.
Reported-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Alex Hung [Thu, 6 Jul 2017 06:50:44 +0000 (23:50 -0700)]
dell-wmi: Add a WMI event code for display on/off
Some new Dell AIO systems have a button that generates a WMI event to
turn the LCD on/off.
BugLink: http://bugs.launchpad.net/bugs/1702541 Signed-off-by: Alex Hung <alex.hung@canonical.com> Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
(backported from commit ab9bb11ccbaa9e84be2534b677fe5350c2cc2014) Signed-off-by: Alex Hung <alex.hung@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: AceLan Kao <acelan.kao@canonical.com> Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Alexander Duyck [Tue, 27 Jun 2017 20:56:37 +0000 (13:56 -0700)]
i40e/i40evf: Limit TSO to 7 descriptors for payload instead of 8 per packet
BugLink: https://bugs.launchpad.net/bugs/1700834
This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet. Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)." It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.
I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.
Fixes: 2d37490b82af ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check") Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(cherry-picked from 3f3f7cb875c0f621485644d4fd7453b0d37f00e4 upstream) Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Netanel Belgazal [Fri, 23 Jun 2017 08:21:59 +0000 (11:21 +0300)]
net: ena: update driver's rx drop statistics
BugLink: http://bugs.launchpad.net/bugs/1701575
rx drop counter is reported by the device in the keep-alive
event.
update the driver's counter with the device counter.
Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 11a9a460199f35f6cbd9d65516a262060cba4fec net-next) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Fri, 23 Jun 2017 08:21:58 +0000 (11:21 +0300)]
net: ena: use lower_32_bits()/upper_32_bits() to split dma address
BugLink: http://bugs.launchpad.net/bugs/1701575
In ena_com_mem_addr_set(), use the above functions to split dma address
to the lower 32 bits and the higher 16 bits.
Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 3ae5907c61587ed8327484bfdda87de0257ea73f net-next) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Fri, 23 Jun 2017 08:21:54 +0000 (11:21 +0300)]
net: ena: add support for out of order rx buffers refill
BugLink: http://bugs.launchpad.net/bugs/1701575
ENA driver post Rx buffers through the Rx submission queue
for the ENA device to fill them with receive packets.
Each Rx buffer is marked with req_id in the Rx descriptor.
Newer ENA devices could consume the posted Rx buffer in out of order,
and as result the corresponding Rx completion queue will have Rx
completion descriptors with non contiguous req_id(s)
In this change the driver holds two rings.
The first ring (called free_rx_ids) is a mapping ring.
It holds all the unused request ids.
The values in this ring are from 0 to ring_size -1.
When the driver wants to allocate a new Rx buffer it uses the head of
free_rx_ids and uses it's value as the index for rx_buffer_info ring.
The req_id is also written to the Rx descriptor
Upon Rx completion,
The driver took the req_id from the completion descriptor and uses it
as index in rx_buffer_info.
The req_id is then return to the free_rx_ids ring.
This patch also adds statistics to inform when the driver receive out
of range or unused req_id.
Note:
free_rx_ids is only accessible from the napi handler, so no locking is
required
Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit ad974baef2a17a170fe837ad19f10dcab63e9470 net-next) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Fri, 23 Jun 2017 08:21:51 +0000 (11:21 +0300)]
net: ena: add hardware hints capability to the driver
BugLink: http://bugs.launchpad.net/bugs/1701575
With this patch, ENA device can update the ena driver about
the desired timeout values:
These values are part of the "hardware hints" which are transmitted
to the driver as Asynchronous event through ENA async
event notification queue.
In case the ENA device does not support this capability,
the driver will use its own default values.
Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 82ef30f13be0b4fea70a9c6215f7cff40bb3be63 net-next) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:50 +0000 (15:42 +0300)]
net: ena: bug fix in lost tx packets detection mechanism
BugLink: http://bugs.launchpad.net/bugs/1701575
check_for_missing_tx_completions() is called from a timer
task and looking for lost tx packets.
The old implementation accumulate all the lost tx packets
and did not check if those packets were retrieved on a later stage.
This cause to a situation where the driver reset
the device for no reason.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 800c55cb76be6617232ef50a2be29830f3aa8e5c) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:48 +0000 (15:42 +0300)]
net: ena: fix theoretical Rx hang on low memory systems
BugLink: http://bugs.launchpad.net/bugs/1701575
For the rare case where the device runs out of free rx buffer
descriptors (in case of pressure on kernel memory),
and the napi handler continuously fail to refill new Rx descriptors
until device rx queue totally runs out of all free rx buffers
to post incoming packet, leading to a deadlock:
* The device won't send interrupts since all the new
Rx packets will be dropped.
* The napi handler won't try to allocate new Rx descriptors
since allocation is part of NAPI that's not being invoked any more
The fix involves detecting this scenario and rescheduling NAPI
(to refill buffers) by the keepalive/watchdog task.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit a3af7c18cfe545a711e5df7491b7d6df71eba2ff) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Netanel Belgazal [Sun, 11 Jun 2017 12:42:46 +0000 (15:42 +0300)]
net: ena: fix race condition between submit and completion admin command
BugLink: http://bugs.launchpad.net/bugs/1701575
Bug:
"Completion context is occupied" error printout will be noticed in
dmesg.
This error will cause the admin command to fail, which will lead to
an ena_probe() failure or a watchdog reset (depends on which admin
command failed).
Root cause:
__ena_com_submit_admin_cmd() is the function that submits new entries to
the admin queue.
The function have a check that makes sure the queue is not full and the
function does not override any outstanding command.
It uses head and tail indexes for this check.
The head is increased by ena_com_handle_admin_completion() which runs
from interrupt context, and the tail index is increased by the submit
function (the function is running under ->q_lock, so there is no risk
of multithread increment).
Each command is associated with a completion context. This context
allocated before call to __ena_com_submit_admin_cmd() and freed by
ena_com_wait_and_process_admin_cq_interrupts(), right after the command
was completed.
This can lead to a state where the head was increased, the check passed,
but the completion context is still in use.
Solution:
Use the atomic variable ->outstanding_cmds instead of using the head and
the tail indexes.
This variable is safe for use since it is bumped in get_comp_ctx() in
__ena_com_submit_admin_cmd() and is freed by comp_ctxt_release()
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 661d2b0ccef6a63f48b61105cf7be17403d1db01) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
check_for_completion()
sleep()
}
So in case the sleep took more than the timeout
(in case the thread/workqueue was not scheduled due to higher priority
task or prolonged VMexit), the driver can detect a stall even if
the completion is present.
The fix changes the order of this function to first check for
completion and only after that check if the timeout expired.
Fixes: 1738cd3ed342 ("Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit a77c1aafcc906f657d1a0890c1d898be9ee1d5c9) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
Lino Sanfilippo [Sat, 18 Feb 2017 11:19:41 +0000 (12:19 +0100)]
net: ena: remove superfluous check in ena_remove()
BugLink: http://bugs.launchpad.net/bugs/1701575
The check in ena_remove() for the pci driver data not being NULL is not
needed, since it is always set in the probe() function. Remove the
superfluous check.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 90a6c997bd8bb836809eda5efb6406d8c58c0924) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com>
mm/mmap.c: expand_downwards: don't require the gap if !vm_prev
expand_stack(vma) fails if address < stack_guard_gap even if there is no
vma->vm_prev. I don't think this makes sense, and we didn't do this
before the recent commit 1be7107fbe18 ("mm: larger stack guard gap,
between vmas").
We do not need a gap in this case, any address is fine as long as
security_mmap_addr() doesn't object.
This also simplifies the code, we know that address >= prev->vm_end and
thus underflow is not possible.
Link: http://lkml.kernel.org/r/20170628175258.GA24881@redhat.com Signed-off-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Cc: Larry Woodman <lwoodman@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CVE-2017-1000364
(cherry picked from commit 32e4e6d5cbb0c0e427391635991fe65e17797af8) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Michal Hocko [Mon, 17 Jul 2017 12:53:28 +0000 (14:53 +0200)]
mm/mmap.c: do not blow on PROT_NONE MAP_FIXED holes in the stack
Commit 1be7107fbe18 ("mm: larger stack guard gap, between vmas") has
introduced a regression in some rust and Java environments which are
trying to implement their own stack guard page. They are punching a new
MAP_FIXED mapping inside the existing stack Vma.
This will confuse expand_{downwards,upwards} into thinking that the
stack expansion would in fact get us too close to an existing non-stack
vma which is a correct behavior wrt safety. It is a real regression on
the other hand.
Let's work around the problem by considering PROT_NONE mapping as a part
of the stack. This is a gros hack but overflowing to such a mapping
would trap anyway an we only can hope that usespace knows what it is
doing and handle it propely.
Fixes: 1be7107fbe18 ("mm: larger stack guard gap, between vmas") Link: http://lkml.kernel.org/r/20170705182849.GA18027@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Debugged-by: Vlastimil Babka <vbabka@suse.cz> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Willy Tarreau <w@1wt.eu> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CVE-2017-1000364
(cherry picked from commit 561b5e0709e4a248c67d024d4d94b6e31e3edf2f) Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Pavel Shilovsky [Mon, 17 Jul 2017 19:29:12 +0000 (16:29 -0300)]
CIFS: Fix null pointer deref during read resp processing
BugLink: https://bugs.launchpad.net/bugs/1704857
Currently during receiving a read response mid->resp_buf can be
NULL when it is being passed to cifs_discard_remaining_data() from
cifs_readv_discard(). Fix it by always passing server->smallbuf
instead and initializing mid->resp_buf at the end of read response
processing.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Acked-by: Sachin Prabhu <sprabhu@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
(cherry picked from commit 350be257ea83029daee974c72b1fe2e6f1f8e615) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
hv_utils: fix TimeSync work on pre-TimeSync-v4 hosts
BugLink: http://bugs.launchpad.net/bugs/1676635
It was found that ICTIMESYNCFLAG_SYNC packets are handled incorrectly
on WS2012R2, e.g. after the guest is paused and resumed its time is set
to something different from host's time. The problem is that we call
adj_guesttime() with reftime=0 for these old hosts and we don't account
for that in 'if (adj_flags & ICTIMESYNCFLAG_SYNC)' branch and
hv_set_host_time().
While we could've solved this by adding a check like
'if (ts_srv_version > TS_VERSION_3)' to hv_set_host_time() I prefer
to do some refactoring. We don't need to have two separate containers
for host samples, struct host_ts which we use for PTP is enough.
Throw away 'struct adj_time_work' and create hv_get_adj_host_time()
accessor to host_ts to avoid code duplication.
Fixes: 3716a49a81ba ("hv_utils: implement Hyper-V PTP source") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from linux-next commit 1d10602d306cb7f70545b5e1166efc9409e7d384) Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
hv_utils: drop .getcrosststamp() support from PTP driver
BugLink: http://bugs.launchpad.net/bugs/1676635
Turns out that our implementation of .getcrosststamp() never actually
worked. Hyper-V is sending time samples every 5 seconds and this is
too much for get_device_system_crosststamp() as it's interpolation
algorithm (which nobody is currently using in kernel, btw) accounts
for a 'slow' device but we're not slow in Hyper-V, our time reference
is too far away.
.getcrosststamp() is not currently used, get_device_system_crosststamp()
almost always returns -EINVAL and client falls back to using PTP_SYS_OFFSET
so this patch doesn't change much. I also tried doing interpolation
manually (e.g. the same way hv_ptp_gettime() works and it turns out that
we're getting even lower quality:
This fact wasn't noticed during the initial testing of the PTP device
somehow but got revealed now. Let's just drop .getcrosststamp()
implementation for now as it doesn't seem to be suitable for us.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from linux-next commit 4f9bac039a64f6306b613a0d90e6b7e75d7ab0c4) Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1676635
With TimeSync version 4 protocol support we started updating system time
continuously through the whole lifetime of Hyper-V guests. Every 5 seconds
there is a time sample from the host which triggers do_settimeofday[64]().
While the time from the host is very accurate such adjustments may cause
issues:
- Time is jumping forward and backward, some applications may misbehave.
- In case an NTP server runs in parallel and uses something else for time
sync (network, PTP,...) system time will never converge.
- Systemd starts annoying you by printing "Time has been changed" every 5
seconds to the system log.
Instead of doing in-kernel time adjustments offload the work to an
NTP client by exposing TimeSync messages as a PTP device. Users may now
decide what they want to use as a source.
I tested the solution with chrony, the config was:
refclock PHC /dev/ptp0 poll 3 dpoll -2 offset 0
The result I'm seeing is accurate enough, the time delta between the guest
and the host is almost always within [-10us, +10us], the in-kernel solution
was giving us comparable results.
I also tried implementing PPS device instead of PTP by using not currently
used Hyper-V synthetic timers (we use only one of four for clockevent) but
with PPS source only chrony wasn't able to give me the required accuracy,
the delta often more that 100us.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3716a49a81ba19dda7202633a68b28564ba95eb5) Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Drivers: hv: util: Use hv_get_current_tick() to get current tick
BugLink: http://bugs.launchpad.net/bugs/1676635
As part of the effort to interact with Hyper-V in an instruction set
architecture independent way, use the new API to get the current
tick.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 305f7549c9298247723c255baddb7a54b4e63050) Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
UBUNTU: SAUCE: hv: make clocksource available for PTP device supporting
BugLink: http://bugs.launchpad.net/bugs/1676635
Make the MSR and TSC clock sources available during the hv_init() and
export them via hyperv_cs in a similar way as the following upstream
commit does:
commit dee863b571b0 ("hv: export current Hyper-V clocksource")
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in BIOS
settings, those ports will be enabled anyway after you remove a device on
that port and re-plug it in again. It's a known limitation of the chip.
As a workaround we can clear the PORT_WAKE_BITS.
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw> Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Shih-Yuan Lee (FourDollars) <sylee@canonical.com> Suggested-by: Owen Lin <olin@rivetnetworks.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
(backported from commit 06e41d8a36689f465006f017bbcd8a73edb98109 linux-next) Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Sachin Prabhu [Fri, 3 Mar 2017 23:41:38 +0000 (15:41 -0800)]
Handle mismatched open calls
BugLink: http://bugs.launchpad.net/bugs/1670508
A signal can interrupt a SendReceive call which result in incoming
responses to the call being ignored. This is a problem for calls such as
open which results in the successful response being ignored. This
results in an open file resource on the server.
The patch looks into responses which were cancelled after being sent and
in case of successful open closes the open fids.
For this patch, the check is only done in SendReceive2()
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Cc: Stable <stable@vger.kernel.org>
(cherry-picked from commit 38bd49064a1ecb67baad33598e3d824448ab11ec) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Sachin Prabhu [Thu, 20 Oct 2016 23:52:24 +0000 (19:52 -0400)]
Call echo service immediately after socket reconnect
BugLink: http://bugs.launchpad.net/bugs/1670508
Commit 4fcd1813e640 ("Fix reconnect to not defer smb3 session reconnect
long after socket reconnect") changes the behaviour of the SMB2 echo
service and causes it to renegotiate after a socket reconnect. However
under default settings, the echo service could take up to 120 seconds to
be scheduled.
The patch forces the echo service to be called immediately resulting a
negotiate call being made immediately on reconnect.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com>
(cherry picked from commit b8c600120fc87d53642476f48c8055b38d6e14c7) Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Pavel Shilovsky [Wed, 1 Mar 2017 00:05:19 +0000 (16:05 -0800)]
CIFS: Fix possible use after free in demultiplex thread
BugLink: http://bugs.launchpad.net/bugs/1670508
The recent changes that added SMB3 encryption support introduced
a possible use after free in the demultiplex thread. When we
process an encrypted packed we obtain a pointer to SMB session
but do not obtain a reference. This can possibly lead to a situation
when this session was freed before we copy a decryption key from
there. Fix this by obtaining a copy of the key rather than a pointer
to the session under a spinlock.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <smfrench@gmail.com>
(cherry picked from commit 61cfac6f267dabcf2740a7ec8a0295833b28b5f5) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>