Ben Hutchings [Wed, 15 Apr 2009 02:48:34 +0000 (19:48 -0700)]
sfc: Use correct macro to set event bitfield
falcon_sim_phy_event() used EFX_OWORD_FIELD, which operates on
bitfields in 128-bit values, on an event, which is a 64-bit value.
This should be harmless - these macros always use little-endian
ordering, so it would read and write back the following 8 bytes
unchanged - but it is obviously wrong.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 15 Apr 2009 02:47:46 +0000 (19:47 -0700)]
sfc: Match calls to netif_napi_add() and netif_napi_del()
sfc could call netif_napi_add() multiple times for the same
napi_struct, corrupting the list of napi_structs for the associated
device and leading to a busy-loop on device removal. Move the call to
netif_napi_add() and add a call to netif_napi_del() in the obvious
places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
e1000/e1000e compile report a possible unused variable, fix
that for now. Shortly after this a small refactor and bug
fix will follow in the same code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Tue, 14 Apr 2009 22:16:55 +0000 (15:16 -0700)]
skge: fix occasional BUG during MTU change
The BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean) in skge_up()
was sometimes observed when setting MTU.
skge_down() disables the TX queue, but then reenables it by mistake via
skge_tx_clean().
Fix it by moving the waking of the queue from skge_tx_clean() to the
other caller. And to make sure start_xmit is not in progress on another
CPU, skge_down() should call netif_tx_disable().
The bug was reported to me by Jiri Jilek whose Debian system sometimes
failed to boot. He tested the patch and the bug did not happen anymore.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 14 Apr 2009 22:11:06 +0000 (15:11 -0700)]
gro: Restore correct value to gso_size
Since everybody has been focusing on baremetal GRO performance
no one noticed when I added a bug that zapped gso_size for all
GRO packets. This only gets picked up when you forward the skb
out of an interface.
Thanks to Mark Wagner for noticing this bug when testing kvm.
Reported-by: Mark Wagner <mwagner@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Mon, 13 Apr 2009 15:51:00 +0000 (15:51 +0000)]
ipv6:remove useless check
After switch (rthdr->type) {...},the check below is completely useless.Because:
if the type is 2,then hdrlen must be 2 and segments_left must be 1,clearly the
check is redundant;if the type is not 2,then goto sticky_done,the check is useless
too.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Reviewed-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 14 Apr 2009 09:09:43 +0000 (02:09 -0700)]
tun: Fix crash with non-GSO users
When I made the tun driver use non-linear packets as the preferred
option, it broke non-GSO users because they would end up allocating
a completely non-linear packet, which triggers a crash when we call
eth_type_trans.
This patch reverts non-GSO users to using linear packets and adds
a check to ensure that GSO users can't cause crashes in the same
way.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan acceleration is used on receive, the vlan tag is maintained
outside of the skb data. The existing vlan tag match only works on TX
path because it uses vlan_get_tag which tests for VLAN_HW_TX_ACCEL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 13 Apr 2009 04:41:01 +0000 (04:41 +0000)]
gro: Normalise skb before bypassing GRO on netpoll VLAN path
Hi:
gro: Normalise skb before bypassing GRO on netpoll VLAN path
When we detect netpoll RX on the GRO VLAN path we bail out and
call the normal VLAN receive handler. However, the packet needs
to be normalised by calling eth_type_trans since that's what the
normal path expects (normally the GRO path does the fixup).
This patch adds the necessary call to vlan_gro_frags.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks, Signed-off-by: David S. Miller <davem@davemloft.net>
phylib: Add interrupt source check function to M88E1121R driver
Add did_interrupt() function to check if a PHY port
really caused an interrupt. This is needed in the case
of shared PHY interrupt pin configuration to stop
interrupt event processing for PHY ports which didn't
cause an interrupt.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
phylib: Basic support for the M88E1121R Marvell chip
Add support for the Marvell M88E1121R Dual GigE PHY
Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
This might work on little endian machines, but it can't on big endian
ones. You have to use the original setting mechanism to be correct on
all architectures.
The attached patch fixes parisc.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
docbook: make cleandocs
kbuild: fix spurious initramfs rebuild
Documentation: explain the difference between __bitwise and __bitwise__
kbuild: make it possible for the linker to discard local symbols from vmlinux
kbuild: remove pointless strdup() on arguments passed to new_module() in modpost
kbuild: fix a few typos in top-level Makefile
kbuild: introduce destination-y for exported headers
kbuild: use git svn instead of git-svn in setlocalversion
kconfig: fix update-po-config to accect backslash in input
kbuild: fix option processing for -I in headerdep
PM/Hibernate: Wait for SCSI devices scan to complete during resume
There is a race between resume from hibernation and the asynchronous
scanning of SCSI devices and to prevent it from happening we need to
call scsi_complete_async_scans() during resume from hibernation.
In addition, if the resume from hibernation is userland-driven, it's
better to wait for all device probes in the kernel to complete before
attempting to open the resume device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add linux kernel support for YMM state
x86: fix wrong section of pat_disable & make it static
x86: Fix section mismatches in mpparse
x86: fix set_fixmap to use phys_addr_t
x86: Document get_user_pages_fast()
x86, intr-remap: fix eoi for interrupt remapping without x2apic
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/filters: return proper error code when writing filter file
tracing/filters: allow user input integer to be oct or hex
tracing/filters: fix NULL pointer dereference
tracing/filters: NIL-terminate user input filter
ftrace: Output REC->var instead of __entry->var for trace format
Make __stringify support variable argument macros too
tracing: fix document references
tracing: fix splice return too large
tracing: update file->f_pos when splice(2) it
tracing: allocate page when needed
tracing: disable seeking for trace_pipe_raw
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: continue lock debugging despite some taints
lockdep: warn about lockdep disabling after kernel taint
work_on_cpu(): rewrite it to create a kernel thread on demand
It seems that the kernel calls these acpi-cpufreq functions at a quite
high frequency.
Valdis Kletnieks also reports that this causes 70-90 forks per second on
his hardware.
Cc: Valdis.Kletnieks@vt.edu Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: Len Brown <len.brown@intel.com> Cc: Zhao Yakui <yakui.zhao@intel.com> Acked-by: Dave Jones <davej@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Tested-by: Mike Galbraith <efault@gmx.de> Cc: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ingo Molnar <mingo@elte.hu>
[ Made it use smp_call_function_many() instead of looping over cpu's
with smp_call_function_single() - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Let new-style drivers implement attach_adapter
i2c: Fix sparse warnings for I2C_BOARD_INFO()
i2c-voodoo3: Deprecate in favor of tdfxfb
i2c-algo-pca: Fix use of uninitialized variable in debug message
When POSIX capabilities were introduced during the 2.1 Linux
cycle, the fs mask, which represents the capabilities which having
fsuid==0 is supposed to grant, did not include CAP_MKNOD and
CAP_LINUX_IMMUTABLE. However, before capabilities the privilege
to call these did in fact depend upon fsuid==0.
This patch introduces those capabilities into the fsmask,
restoring the old behavior.
See the thread starting at http://lkml.org/lkml/2009/3/11/157 for
reference.
Note that if this fix is deemed valid, then earlier kernel versions (2.4
and 2.2) ought to be fixed too.
Changelog:
[Mar 23] Actually delete old CAP_FS_SET definition...
[Mar 20] Updated against J. Bruce Fields's patch
Reported-by: Igor Zhbanov <izh1979@gmail.com> Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Cc: stable@kernel.org Cc: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: unbreak alpha percpu
mutex: have non-spinning mutexes on s390 by default
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] omap_wdt.c: move probe function to .devinit.text
[WATCHDOG] ks8695_wdt.c: move probe function to .devinit.text
[WATCHDOG] at91rm9200_wdt.c: move probe function to .devinit.text
[WATCHDOG] remove ARM26 sections
[WATCHDOG] orion5x_wdt: Add shutdown callback, use watchdog ping function
[WATCHDOG] i6300esb.c: Restructure initialization of the device
[WATCHDOG] i6300esb.c: Fix the GETSTATUS and GETBOOTSTATUS ioctls.
[WATCHDOG] i6300esb.c: Cleanup
Jean Delvare [Mon, 13 Apr 2009 15:02:14 +0000 (17:02 +0200)]
i2c: Let new-style drivers implement attach_adapter
While it isn't the way the standard device binding model works, it is
OK for new-style drivers to implement attach_adapter. It may help
convert the renaming legacy drivers to new style drivers faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
Ben Hutchings [Mon, 13 Apr 2009 15:02:14 +0000 (17:02 +0200)]
i2c: Fix sparse warnings for I2C_BOARD_INFO()
Since the first argument to I2C_BOARD_INFO() must be a string constant,
there is no need to parenthesise it, and adding parentheses results in
an invalid initialiser for char[]. gcc obviously accepts this syntax as
an extension, but sparse complains, e.g.:
drivers/net/sfc/boards.c:173:2: warning: array initialized from parenthesized string constant
Therefore, remove the parentheses.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Brian Haley [Mon, 13 Apr 2009 07:11:30 +0000 (00:11 -0700)]
Bonding: fix zero address hole bug in arp_ip_target list
Fix a zero address hole bug in the bonding arp_ip_target list
that was causing the bond to ignore ARP replies (bugz 13006).
Instead of just setting the array entry to zero, we now
copy any additional entries down one slot, putting the
zero entry at the end. With this change we can now have
all the loops that walk the array stop when they hit a zero
since there will be no addresses after it.
Changes are based in part on code fragment provided in kernel:
bugzilla 13006:
http://bugzilla.kernel.org/show_bug.cgi?id=13006
by Steve Howard <steve@astutenetworks.com>
Signed-off-by: Brian Haley <brian.haley@hp.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
lockdep: continue lock debugging despite some taints
Impact: broaden lockdep checks
Lockdep is disabled after any kernel taints. This might be convenient
to ignore bad locking issues which sources come from outside the kernel
tree. Nevertheless, it might be a frustrating experience for the
staging developers or those who experience a warning but are focused
on another things that require lockdep.
The v2 of this patch simply don't disable anymore lockdep in case
of TAINT_CRAP and TAINT_WARN events.
lockdep: warn about lockdep disabling after kernel taint
Impact: provide useful missing info for developers
Kernel taint can occur in several situations such as warnings,
load of prorietary or staging modules, bad page, etc...
But when such taint happens, a developer might still be working on
the kernel, expecting that lockdep is still enabled. But a taint
disables lockdep without ever warning about it.
Such a kernel behaviour doesn't really help for kernel development.
This patch adds this missing warning.
Since the taint is done most of the time after the main message that
explain the real source issue, it seems safe to warn about it inside
add_taint() so that it appears at last, without hurting the main
information.
v2: Use a generic helper to disable lockdep instead of an
open coded xchg().
Marcin Slusarz [Fri, 10 Apr 2009 20:47:17 +0000 (22:47 +0200)]
x86: fix wrong section of pat_disable & make it static
pat_disable cannot be __cpuinit anymore because it's called from pat_init
and the callchain looks like this:
pat_disable [cpuinit] <- pat_init <- generic_set_all <-
ipi_handler <- set_mtrr <- (other non init/cpuinit functions)
WARNING: arch/x86/mm/built-in.o(.text+0x449e): Section mismatch in reference
from the function pat_init() to the function .cpuinit.text:pat_disable()
The function pat_init() references
the function __cpuinit pat_disable().
This is often because pat_init lacks a __cpuinit
annotation or the annotation of pat_disable is wrong.
Non CONFIG_X86_PAT version of pat_disable is static inline, so this version
can be static too (and there are no callers outside of this file).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <49DFB055.6070405@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
In arch/x86/kernel/mpparse.c, smp_reserve_bootmem() has been called
and also refers to a function which is in .init section. Thus causes
the first warning. And check_irq_src() also requires an __init,
because it refers to an .init section.
This reverts commit 5d38258ec026921a7b266f4047ebeaa75db358e5, since the
underlying problem got fixed properly in the previous commit ("async:
Fix module loading async-work regression").
Cc: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com> Cc: Vegard Nossum <vegard.nossum@gmail.com> Cc: Len Brown <len.brown@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several drivers use asynchronous work to do device discovery, and we
synchronize with them in the compiled-in case before we actually try to
mount root filesystems etc.
However, when compiled as modules, that synchronization is missing - the
module loading completes, but the driver hasn't actually finished
probing for devices, and that means that any user mode that expects to
use the devices after the 'insmod' is now potentially broken.
We already saw one case of a similar issue in the ACPI battery code,
where the kernel itself expected the module to be all done, and unmapped
the init memory - but the async device discovery was still running.
That got hacked around by just removing the "__init" (see commit 5d38258ec026921a7b266f4047ebeaa75db358e5 "ACPI battery: fix async boot
oops"), but the real fix is to just make the module loading wait for all
async work to be completed.
It will slow down module loading, but since common devices should be
built in anyway, and since the bug is really annoying and hard to handle
from user space (and caused several S3 resume regressions), the simple
fix to wait is the right one.
This fixes at least
http://bugzilla.kernel.org/show_bug.cgi?id=13063
but probably a few other bugzilla entries too (12936, for example), and
is confirmed to fix Rafael's storage driver breakage after resume bug
report (no bugzilla entry).
We should also be able to now revert that ACPI battery fix.
Reported-and-tested-by: Rafael J. Wysocki <rjw@suse.com> Tested-by: Heinz Diehl <htd@fancy-poultry.org> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Duyck [Thu, 9 Apr 2009 22:49:39 +0000 (22:49 +0000)]
igb: do not check for vf_data if we didn't enable vfs
The driver is currently dumping a message in the log about failing to
allocate vf data when max_vfs is equal to 0. This change makes it so the
error message is only displayed if we set max_vfs to a non zero value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 9 Apr 2009 22:49:20 +0000 (22:49 +0000)]
igbvf: fix unused external references
The igbvbf driver exposed several unused extrnal references due to the fact
that code was copied from igb and then some functionality was removed.
This changes that so that unused functions are either removed or made
static.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 9 Apr 2009 22:49:02 +0000 (22:49 +0000)]
igb: fix unused external references introduced with sr-iov changes
There were several unused external references added with the sr-iov
enablement changes. This patch changes all those references to static
local references.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Fix NULL pointer dereference with time-wait sockets
Commit b2f5e7cd3dee2ed721bf0675e1a1ddebb849aee6
(ipv6: Fix conflict resolutions during ipv6 binding)
introduced a regression where time-wait sockets were
not treated correctly. This resulted in the following:
Tested-by: Brian Haley <brian.haley@hp.com> Tested-by: Ed Tomlinson <edt@aei.ca> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 8 Apr 2009 13:20:50 +0000 (13:20 +0000)]
ixgbe: only allow WOL for 82599 KX4 NIC
All NICs were reporting WOL support when only the KX4 NIC is capable of
supporting WOL. This patch adds a function to check for and exclude all
non-WOL capable nics from enabling WOL in ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe: Move the LED blink code to common, since 82599 also uses it
The LED blink code is common for 82599 as well. It should be moved to
ixgbe_common.c so both devices can use it, and not have it duplicated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 8 Apr 2009 13:15:22 +0000 (13:15 +0000)]
net: netif_device_attach/detach should start/stop all queues
Currently netif_device_attach/detach are only stopping one queue. They
should be starting and stopping all the queues on a given device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Bizon [Mon, 9 Feb 2009 17:49:52 +0000 (18:49 +0100)]
kbuild: fix spurious initramfs rebuild
When gen_initramfs_list is used to generate make dependencies, it
includes symbolic links, for which make tracks the link target. Any
change to that target will cause an initramfs rebuild, even if the
symlink points to something outside of the initramfs directory.
If the target happens to be /tmp, the rebuild occurs for each kernel
build, since gen_initramfs_list uses mktemp...
Proposed way to fix it is to omit symbolic links from generated
dependencies, but this has a small drawback: changing perm/owner on a
symlink will go unnoticed.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
David Howells [Wed, 4 Mar 2009 19:59:07 +0000 (11:59 -0800)]
kbuild: make it possible for the linker to discard local symbols from vmlinux
Make it possible for the linker to discard local symbols from vmlinux as
they cause vmlinux to balloon when CONFIG_KALLSYMS=y and they cause
dump_stack() and get_wchan() to produce useless information under some
circumstances.
With this we add a config option (CONFIG_STRIP_ASM_SYMS) that will cause
the build to supply -X to the linker to tell it to strip temporary local
symbols.
This doesn't seem to cause gdb any problems.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sam Ravnborg [Fri, 10 Apr 2009 06:52:43 +0000 (08:52 +0200)]
kbuild: introduce destination-y for exported headers
xtensa and arm have asked for a possibility to export headers
and locate them in a specific directory when exported.
Introduce destiantion-y to support this.
This patch in additiona adds some limited
documentation for the variables used for exported headers.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Oskar Schirmer <os@emlix.com> Cc: Mikael Starvik <mikael.starvik@axis.com>
Sam Ravnborg [Wed, 8 Apr 2009 06:42:48 +0000 (08:42 +0200)]
kconfig: fix update-po-config to accect backslash in input
Massimo Maiurana reported (slightly edited):
=====
In latest 2.6.29 "make update-po-config" fails at msguniq invocation
with an "invalid control sequence" error.
The offending string is the following, and it's located in
drivers/staging/panel/Kconfig:72:
"'\e[L' which are specific to the LCD, and a few ANSI codes. The"
looks to me like gettext expects strings in printf format, so in
this case it thinks "\e" is a control sequence but doesn't recognise
it as a valid one.
A valid solution would be to tell kxgettext to automatically
escape this kind of strings in the */config.pot he produces, so that
msguniq would not complain.
=====
David Woodhouse [Sat, 11 Apr 2009 05:27:48 +0000 (22:27 -0700)]
intel-iommu: Avoid panic() for DRHD at address zero.
If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.
It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
projects / mirror_ubuntu-kernels.git / log