Danielle Ratson [Mon, 20 Dec 2021 10:56:14 +0000 (12:56 +0200)]
mlxsw: core: Extend devlink health reporter with new events and parameters
Extend the devlink health reporter registered by mlxsw to report new
health events and their related parameters. These are meant to aid in
debugging of hardware / firmware issues.
Beside the test event ('MLXSW_REG_MFDE_EVENT_ID_TEST') that is triggered
following the devlink health 'test' sub-command, the new events are used
to report the triggering of asserts in firmware code
('MLXSW_REG_MFDE_EVENT_ID_FW_ASSERT') and hardware issues
('MLXSW_REG_MFDE_EVENT_ID_FATAL_CAUSE').
Each event is accompanied with a severity parameter and per-event
parameters that are meant to help root cause the detected issue.
Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Danielle Ratson [Mon, 20 Dec 2021 10:56:13 +0000 (12:56 +0200)]
mlxsw: reg: Extend MFDE register with new events and parameters
Extend the Monitoring Firmware Debug (MFDE) register with new events and
their related parameters. These events will be utilized by
devlink-health in the next patch.
Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Danielle Ratson [Mon, 20 Dec 2021 10:56:12 +0000 (12:56 +0200)]
mlxsw: core: Convert a series of if statements to switch case
Convert a series of if statements that handle different events to a
switch case statement. Encapsulate the per-event code in different
functions to simplify the code.
This is a preparation for subsequent patches that will add more events
that need to be handled.
Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Danielle Ratson [Mon, 20 Dec 2021 10:56:11 +0000 (12:56 +0200)]
mlxsw: Fix naming convention of MFDE fields
Currently, the MFDE register field names are using the convention:
reg_mfde_<NAME_OF_FIELD>, and do not consider the name of the MFDE
event.
Fix the field names so they fit the more accurate convention:
reg_mfde_<NAME_OF_EVENT>_<NAME_OF_FIELD>.
Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 17 Dec 2021 16:55:52 +0000 (08:55 -0800)]
bnx2x: Invalidate fastpath HSI version for VFs
Commit 0a6890b9b4df ("bnx2x: Utilize FW 7.13.15.0.")
added validation for fastpath HSI versions for different
client init which was not meant for SR-IOV VF clients, which
resulted in firmware asserts when running VF clients with
different fastpath HSI version.
This patch along with the new firmware support in patch #1
fixes this behavior in order to not validate fastpath HSI
version for the VFs.
Fixes: 0a6890b9b4df ("bnx2x: Utilize FW 7.13.15.0.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Alok Prasad <palok@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Fri, 17 Dec 2021 16:55:51 +0000 (08:55 -0800)]
bnx2x: Utilize firmware 7.13.21.0
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by: Alok Prasad <palok@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 19 Dec 2021 14:08:48 +0000 (14:08 +0000)]
Merge branch 'tc-action-offload'
Simon Horman says:
====================
allow user to offload tc action to net device
Baowen Zheng says:
Allow use of flow_indr_dev_register/flow_indr_dev_setup_offload to offload
tc actions independent of flows.
The motivation for this work is to prepare for using TC police action
instances to provide hardware offload of OVS metering feature - which calls
for policers that may be used by multiple flows and whose lifecycle is
independent of any flows that use them.
This patch includes basic changes to offload drivers to return EOPNOTSUPP
if this feature is used - it is not yet supported by any driver.
Tc cli command to offload and quote an action:
# tc qdisc del dev $DEV ingress && sleep 1 || true
# tc actions delete action police index 200 || true
# tc qdisc add dev $DEV ingress
# tc qdisc show dev $DEV ingress
# tc actions add action police rate 100mbit burst 10000k index 200 skip_sw
# tc -s -d actions list action police
total acts 1
Changes between v7 and v8:
* Rename enum offload_act_command as enum flow_offload_act_command
* Add a single patch to rename exts stats update function for readability.
* Fix the kernel test robot issue reported by Oliver Sang.
Changes between v6 and v7:
* Add a single patch to rename offload functions with offload for readability.
* Post 166b6a46b78b ("flow_offload: return EOPNOTSUPP for the unsupported mpls action type") as a bug fix to netdev.
* Rename enum flow_act_command as enum flow_offload_act_command
* Rename the new added action offload setup ops with offload instead of flow
* Rename the new added action offload function with offload instead of flow.
* Add more selftest cases for validate filter and actions.
Changes between v5 and v6:
* Fix issue reported by Dan Carpenter found using Smatch.
Changes beteeen v4 and v5:
* Made changes of code style according to the public review comments.
* Add a fix for unsupported mpls action type in flow action setup stage.
* Add ops to tc_action_ops for flow action setup to facilitate
adding a standalone action module.
* Add notification process when deleting action in reoffload process.
Changes between v3 and v4:
* Made changes according to the public review comments.
* Validate flags inside tcf_action_init() instead of creating new
tcf_exts_validate_actions() function.
* Exactly match when validating flags of actions and filters.
* Add index to flow_action_entry for driver to identify actions.
Changes between v2 and v3:
* Made changes according to the review comments.
* Delete in_hw and not_in_hw flag and user can judge if the action is
offloaded to any hardware by in_hw_count.
* Split the main patch of the action offload to three single patch to
facilitate code review.
Changes between v1 and v2:
* Add the skip_hw/skip_sw for user to specify if the action should be in
hardware or software.
* Fix issue of sleeping function called from invalid context.
* Change the action offload/delete from batch to one by one.
* Add some parameters to the netlink message for user space to look up
the offload status of the actions.
* Add reoffload process to update action hw_count when driver is inserted
or removed.
Changes between v1 and RFC:
* Fix robot test failure.
* Change actions offload process in action add function rather than action
init.
* Change actions offload delete process after tcf_del_notify to keep
undeleted actions.
* Add process to update actions stats from hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:29 +0000 (19:16 +0100)]
selftests: tc-testing: add action offload selftest for action and filter
Add selftest cases in action police with skip_hw.
Add selftest case to validate flags of filter and action.
These tests depend on corresponding iproute2 command support.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:28 +0000 (19:16 +0100)]
flow_offload: validate flags of filter and actions
Add process to validate flags of filter and actions when adding
a tc filter.
We need to prevent adding filter with flags conflicts with its actions.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:27 +0000 (19:16 +0100)]
flow_offload: add reoffload process to update hw_count
Add reoffload process to update hw_count when driver
is inserted or removed.
We will delete the action if it is with skip_sw flag and
not offloaded to any hardware in reoffload process.
When reoffloading actions, we still offload the actions
that are added independent of filters.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:26 +0000 (19:16 +0100)]
net: sched: save full flags for tc action
Save full action flags and return user flags when return flags to
user space.
Save full action flags to distinguish if the action is created
independent from classifier.
We made this change mainly for further patch to reoffload tc actions.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:25 +0000 (19:16 +0100)]
flow_offload: add process to update action stats from hardware
When collecting stats for actions update them using both
hardware and software counters.
Stats update process should not run in context of preempt_disable.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:24 +0000 (19:16 +0100)]
flow_offload: rename exts stats update functions with hw
Rename exts stats update functions with hw for readability.
We make this change also to update stats from hw for an action
when it is offloaded to hw as a single action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:23 +0000 (19:16 +0100)]
flow_offload: add skip_hw and skip_sw to control if offload the action
We add skip_hw and skip_sw for user to control if offload the action
to hardware.
We also add in_hw_count for user to indicate if the action is offloaded
to any hardware.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:22 +0000 (19:16 +0100)]
flow_offload: allow user to offload tc action to net device
Use flow_indr_dev_register/flow_indr_dev_setup_offload to
offload tc action.
We need to call tc_cleanup_flow_action to clean up tc action entry since
in tc_setup_action, some actions may hold dev refcnt, especially the mirror
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:21 +0000 (19:16 +0100)]
flow_offload: add ops to tc_action_ops for flow action setup
Add a new ops to tc_action_ops for flow action setup.
Refactor function tc_setup_flow_action to use this new ops.
We make this change to facilitate to add standalone action module.
We will also use this ops to offload action independent of filter
in following patch.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:20 +0000 (19:16 +0100)]
flow_offload: rename offload functions with offload instead of flow
To improves readability, we rename offload functions with offload instead
of flow.
The term flow is related to exact matches, so we rename these functions
with offload.
We make this change to facilitate single action offload functions naming.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:19 +0000 (19:16 +0100)]
flow_offload: add index to flow_action_entry structure
Add index to flow_action_entry structure and delete index from police and
gate child structure.
We make this change to offload tc action for driver to identify a tc
action.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:18 +0000 (19:16 +0100)]
flow_offload: reject to offload tc actions in offload drivers
A follow-up patch will allow users to offload tc actions independent of
classifier in the software datapath.
In preparation for this, teach all drivers that support offload of the flow
tables to reject such configuration as currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Baowen Zheng [Fri, 17 Dec 2021 18:16:17 +0000 (19:16 +0100)]
flow_offload: fill flags to action structure
Fill flags to action structure to allow user control if
the action should be offloaded to hardware or not.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 18 Dec 2021 12:22:17 +0000 (12:22 +0000)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-12-17
Brett Creeley says:
This patch series adds support in the iavf driver for communicating and
using VIRTCHNL_VF_OFFLOAD_VLAN_V2. The current VIRTCHNL_VF_OFFLOAD_VLAN
is very limited and covers all 802.1Q VLAN offloads and filtering with
no granularity.
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 adds more granularity, flexibility,
and support for 802.1ad offloads and filtering. This includes the VF
negotiating which VLAN offloads/filtering it's allowed, where VLAN tags
should be inserted and/or stripped into and from descriptors, and the
supported VLAN protocols.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mptcp: Miscellaneous changes for 5.17
These are three unrelated patches that we've been testing in the MPTCP
tree.
Patch 1 modifies the packet scheduler that picks which TCP subflow is
used for each chunk of outgoing data. The updated scheduler improves
throughput on multiple-subflow connections.
Patch 2 updates a selftest to verify recent TCP_ULP sockopt changes
on MPTCP fallback sockets.
Patch 3 cleans up some unnecessary comparisons with an 8-bit value.
====================
Florian Westphal [Fri, 17 Dec 2021 23:37:01 +0000 (15:37 -0800)]
selftests: mptcp: try to set mptcp ulp mode in different sk states
The kernel will crash without
'mptcp: clear 'kern' flag from fallback sockets' change.
Since this doesn't slow down testing in a noticeable way,
run this unconditionally.
The explicit test did not catch this, because the check was done
for tcp socket returned by 'socket(.. IPPROTO_TCP) rather than a
tcp socket returned by accept() on a mptcp listen fd.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 17 Dec 2021 23:37:00 +0000 (15:37 -0800)]
mptcp: enforce HoL-blocking estimation
The MPTCP packet scheduler has sub-optimal behavior with asymmetric
subflows: if the faster subflow-level cwin is closed, the packet
scheduler can enqueue "too much" data on a slower subflow.
When all the data on the faster subflow is acked, if the mptcp-level
cwin is closed, and link utilization becomes suboptimal.
The solution is implementing blest-like[1] HoL-blocking estimation,
transmitting only on the subflow with the shorter estimated time to
flush the queued memory. If such subflows cwin is closed, we wait
even if other subflows are available.
This is quite simpler than the original blest implementation, as we
leverage the pacing rate provided by the TCP socket. To get a more
accurate estimation for the subflow linger-time, we maintain a
per-subflow weighted average of such info.
Additionally drop magic numbers usage in favor of newly defined
macros and use more meaningful names for status variable.
Dan Carpenter [Fri, 17 Dec 2021 07:10:37 +0000 (10:10 +0300)]
net: ethernet: mtk_eth_soc: delete some dead code
The debugfs_create_dir() function never returns NULL. It does return
error pointers but in normal situations like this there is no need to
check for errors.
Gerhard Engleder [Thu, 16 Dec 2021 20:01:54 +0000 (21:01 +0100)]
tsnep: Fix s390 devm_ioremap_resource warning
The following warning is fixed with additional config dependencies:
s390-linux-ld: drivers/net/ethernet/engleder/tsnep_main.o: in function `tsnep_probe':
tsnep_main.c:(.text+0x1de6): undefined reference to `devm_ioremap_resource'
Brett Creeley [Tue, 30 Nov 2021 00:16:04 +0000 (16:16 -0800)]
iavf: Restrict maximum VLAN filters for VIRTCHNL_VF_OFFLOAD_VLAN_V2
For VIRTCHNL_VF_OFFLOAD_VLAN, PF's would limit the number of VLAN
filters a VF was allowed to add. However, by the time the opcode failed,
the VLAN netdev had already been added. VIRTCHNL_VF_OFFLOAD_VLAN_V2
added the ability for a PF to tell the VF how many VLAN filters it's
allowed to add. Make changes to support that functionality.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:03 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 offload enable/disable
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if
successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
Multiple changes were needed to support this new functionality.
1. Added new aq_required flags to support any kind of VLAN stripping and
insertion offload requests via virtchnl.
2. Added the new method iavf_set_vlan_offload_features() that's
used during VF initialization, VF reset, and iavf_set_features() to
set the aq_required bits based on the current VLAN offload
configuration of the VF's netdev.
3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2,
VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2,
and VIRTCHNL_OP_ENABLE_INSERTION_V2.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:02 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 hotpath
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows
the PF to set the location of the Tx and Rx VLAN tag for insertion and
stripping offloads. In order to support this functionality a few changes
are needed.
1. Add a new method to cache the VLAN tag location based on negotiated
capabilities for the Tx and Rx ring flags. This needs to be called in
the initialization and reset paths.
2. Refactor the transmit hotpath to account for the new Tx ring flags.
When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to
insert the VLAN tag in the L2TAG2 field of the transmit descriptor.
When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs
to use the l2tag1 field of the data descriptor (same behavior as
before).
3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify
transmit hardware VLAN offload functionality by only depending on the
skb_vlan_tag_present() function. This can be done because the OS
won't request transmit offload for a VLAN unless the driver told the
OS it's supported and enabled.
4. Refactor the receive hotpath to account for the new Rx ring flags and
VLAN ethertypes. This requires checking the Rx ring flags and
descriptor status bits to determine the location of the VLAN tag.
Also, since only a single ethertype can be supported at a time, check
the enabled netdev features before specifying a VLAN ethertype in
__vlan_hwaccel_put_tag().
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:01 +0000 (16:16 -0800)]
iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config
Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN
capabilities (i.e. 802.1AD offloads and filtering). In order to
communicate these capabilities to the netdev layer, the VF needs to
parse its VLAN capabilities based on whether it was able to negotiation
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of
these.
In order to support this, add the following functionality:
iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN
features that the underlying hardware supports and that can be toggled
off/on based on the negotiated capabiltiies. For example, if
VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked
with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If
VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or
stripping can be toggled on/off.
iavf_get_netdev_vlan_features() - This is used to determine the VLAN
features that the underlying hardware supports and that should be
enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was
negotiated, then any supported capability that has its ethertype_init
filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was
negotiated, then filtering, stripping, and insertion should be enabled
by default.
Also, refactor iavf_fix_features() to take into account the new
capabilities. To do this, query all the supported features (enabled by
default and toggleable) and make sure the requested change is supported.
If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no
need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told
the netdev layer which features can be toggled via netdev->hw_features
during iavf_process_config(), so only those features will be requested
to change.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:16:00 +0000 (16:16 -0800)]
iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation
In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the
VF driver needs to rework it's initialization state machine and reset
flow. This has to be done because successful negotiation of
VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second
capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before
configuring the adapter and its netdev.
Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the
VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either
support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or
neither. Both of these offloads should never be supported together.
Based on this, add 2 new states to the initialization state machine:
The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store
the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2
was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state.
The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the
adapter/netdev after the resource requests have finished. The VF will
move into this state regardless of whether it successfully negotiated
VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2.
Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set
it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully
negotiated then the VF will request its VLAN capabilities via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed
because the PF may change/modify the VF's configuration during VF reset
(i.e. modifying the VF's port VLAN configuration).
This also, required the VF to call netdev_update_features() since its
VLAN features may change during VF reset. Make sure to call this under
rtnl_lock().
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Brett Creeley [Tue, 30 Nov 2021 00:15:59 +0000 (16:15 -0800)]
virtchnl: Add support for new VLAN capabilities
Currently VIRTCHNL only allows for VLAN filtering and offloads to happen
on a single 802.1Q VLAN. Add support to filter and offload on inner,
outer, and/or inner + outer VLANs.
This is done by introducing the new capability
VIRTCHNL_VF_OFFLOAD_VLAN_V2. The flow to negotiate this new capability
is shown below.
1. VF - sets the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit in the
virtchnl_vf_resource.vf_caps_flags during the
VIRTCHNL_OP_GET_VF_RESOURCES request message. The VF should also set
the VIRTCHNL_VF_OFFLOAD_VLAN bit in case the PF driver doesn't support
the new capability.
2. PF - sets the VLAN capability bit it supports in the
VIRTCHNL_OP_GET_VF_RESOURCES response message. This will either be
VIRTCHNL_VF_OFFLOAD_VLAN_V2, VIRTCHNL_VF_OFFLOAD_VLAN, or none.
3. VF - If the VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability was ACK'd by the
PF, then the VF needs to request the VLAN capabilities of the
PF/Device by issuing a VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS request.
If the VIRTCHNL_VF_OFFLOAD_VLAN capability was ACK'd then the VF
knows only single 802.1Q VLAN filtering/offloads are supported. If no
VLAN capability is ACK'd then the PF/Device doesn't support hardware
VLAN filtering/offloads for this VF.
4. PF - Populates the virtchnl_vlan_caps structure based on what it
allows/supports for that VF and sends that response via
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS.
After VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is successfully negotiated
the VF driver needs to interpret the capabilities supported by the
underlying PF/Device. The VF will be allowed to filter/offload the
inner 802.1Q, outer (various ethertype), inner 802.1Q + outer
(various ethertypes), or none based on which fields are set.
The VF will also need to interpret where the VLAN tag should be inserted
and/or stripped based on the negotiated capabilities.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jakub Kicinski [Fri, 17 Dec 2021 15:30:06 +0000 (07:30 -0800)]
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Changcheng Deng [Thu, 16 Dec 2021 09:13:39 +0000 (09:13 +0000)]
net: dsa: microchip: remove unneeded variable
Remove unneeded variable used to store return value.
Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Dexuan Cui [Thu, 16 Dec 2021 00:17:48 +0000 (16:17 -0800)]
net: mana: Add RX fencing
RX fencing allows the driver to know that any prior change to the RQs has
finished, e.g. when the RQs are disabled/enabled or the hashkey/indirection
table are changed, RX fencing is required.
Remove the previous workaround "ssleep(1)" and add the real support for
RX fencing as the PF driver supports the MANA_FENCE_RQ request now (any
old PF driver not supporting the request won't be used in production).
Yinjun Zhang [Thu, 16 Dec 2021 01:37:01 +0000 (20:37 -0500)]
nfp: flower: refine the use of circular buffer
The current use of circular buffer to manage stats_context_id is
very obscure, and it will cause problem if its element size is
not power of two. So change the use more straightforward and
scalable, and also change that for mask_id to keep consistency.
Linus Torvalds [Thu, 16 Dec 2021 23:02:14 +0000 (15:02 -0800)]
Merge tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from mac80211, wifi, bpf.
Relatively large batches of fixes from BPF and the WiFi stack, calm in
general networking.
Current release - regressions:
- dpaa2-eth: fix buffer overrun when reporting ethtool statistics
Current release - new code bugs:
- bpf: fix incorrect state pruning for <8B spill/fill
- iavf:
- add missing unlocks in iavf_watchdog_task()
- do not override the adapter state in the watchdog task (again)
- mlxsw: spectrum_router: consolidate MAC profiles when possible
Previous releases - regressions:
- mac80211 fixes:
- rate control, avoid driver crash for retransmitted frames
- regression in SSN handling of addba tx
- a memory leak where sta_info is not freed
- marking TX-during-stop for TX in in_reconfig, prevent stall
- cfg80211: acquire wiphy mutex on regulatory work
- wifi drivers: fix build regressions and LED config dependency
- virtio_net: fix rx_drops stat for small pkts
- dsa: mv88e6xxx: unforce speed & duplex in mac_link_down()
Previous releases - always broken:
- bpf fixes:
- kernel address leakage in atomic fetch
- kernel address leakage in atomic cmpxchg's r0 aux reg
- signed bounds propagation after mov32
- extable fixup offset
- extable address check
- mac80211:
- fix the size used for building probe request
- send ADDBA requests using the tid/queue of the aggregation
session
- agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid
deadlocks
- validate extended element ID is present
- mptcp:
- never allow the PM to close a listener subflow (null-defer)
- clear 'kern' flag from fallback sockets, prevent crash
- fix deadlock in __mptcp_push_pending()
- inet_diag: fix kernel-infoleak for UDP sockets
- xsk: do not sleep in poll() when need_wakeup set
- smc: avoid very long waits in smc_release()
- sch_ets: don't remove idle classes from the round-robin list
- netdevsim:
- zero-initialize memory for bpf map's value, prevent info leak
- don't let user space overwrite read only (max) ethtool parms
- ixgbe: set X550 MDIO speed before talking to PHY
- stmmac:
- fix null-deref in flower deletion w/ VLAN prio Rx steering
- dwmac-rk: fix oob read in rk_gmac_setup
- ice: time stamping fixes
- systemport: add global locking for descriptor life cycle"
* tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits)
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
sit: do not call ipip6_dev_free() from sit_init_net()
net: systemport: Add global locking for descriptor lifecycle
net/smc: Prevent smc_release() from long blocking
net: Fix double 0x prefix print in SKB dump
virtio_net: fix rx_drops stat for small pkts
dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
sfc_ef100: potential dereference of null pointer
net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
net: usb: lan78xx: add Allied Telesis AT29M2-AF
net/packet: rx_owner_map depends on pg_vec
netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
dpaa2-eth: fix ethtool statistics
ixgbe: set X550 MDIO speed before talking to PHY
...
Linus Torvalds [Thu, 16 Dec 2021 22:48:57 +0000 (14:48 -0800)]
Merge tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of DT fixes, mostly for mistakes found through
static checking of the dts files again, as well as a couple of minor
changes to address incorrect DT settings.
For i.MX, there is yet another series of devitree changes to update
RGMII delay settings for ethernet, which is an ongoing problem after
some driver changes.
For SoC specific device drivers, a number of smaller fixes came up:
- i.MX SoC identification was incorrectly registered non-i.MX
machines when the driver is built-in
- One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work
properly
- a few compile fixes for warnings that get in the way of -Werror
- a string overflow in the scpi firmware driver
- a boot failure with FORTIFY_SOURCE on Rockchips machines
- broken error handling in the AMD TEE driver
- a revert for a tegra reset driver commit that broke HDA"
* tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
soc/tegra: fuse: Fix bitwise vs. logical OR warning
firmware: arm_scpi: Fix string overflow in SCPI genpd driver
soc: imx: Register SoC device only on i.MX boards
soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset
ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
arm64: dts: imx8mq: remove interconnect property from lcdif
ARM: socfpga: dts: fix qspi node compatible
arm64: dts: apple: add #interrupt-cells property to pinctrl nodes
dt-bindings: i2c: apple,i2c: allow multiple compatibles
arm64: meson: remove COMMON_CLK
arm64: meson: fix dts for JetHub D1
tee: amdtee: fix an IS_ERR() vs NULL bug
arm64: dts: apple: change ethernet0 device type to ethernet
arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
arm64: dts: rockchip: fix poweroff on helios64
arm64: dts: rockchip: fix audio-supply for Rock Pi 4
arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge
ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up
...
We've added 15 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 434 insertions(+), 30 deletions(-).
The main changes are:
1) Fix incorrect verifier state pruning behavior for <8B register spill/fill,
from Paul Chaignon.
2) Fix x86-64 JIT's extable handling for fentry/fexit when return pointer
is an ERR_PTR(), from Alexei Starovoitov.
3) Fix 3 different possibilities that BPF verifier missed where unprivileged
could leak kernel addresses, from Daniel Borkmann.
4) Fix xsk's poll behavior under need_wakeup flag, from Magnus Karlsson.
5) Fix an oob-write in test_verifier due to a missed MAX_NR_MAPS bump,
from Kumar Kartikeya Dwivedi.
6) Fix a race in test_btf_skc_cls_ingress selftest, from Martin KaFai Lau.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
selftest/bpf: Add a test that reads various addresses.
bpf: Fix extable address check.
bpf: Fix extable fixup offset.
bpf, selftests: Add test case trying to taint map value pointer
bpf: Make 32->64 bounds propagation slightly more robust
bpf: Fix signed bounds propagation after mov32
bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer
bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg
bpf, selftests: Add test case for atomic fetch on spilled pointer
bpf: Fix kernel address leakage in atomic fetch
selftests/bpf: Fix OOB write in test_verifier
xsk: Do not sleep in poll() when need_wakeup set
selftests/bpf: Tests for state pruning with u32 spill/fill
bpf: Fix incorrect state pruning for <8B spill/fill
====================
Martin KaFai Lau [Thu, 16 Dec 2021 19:16:30 +0000 (11:16 -0800)]
bpf, selftests: Fix racing issue in btf_skc_cls_ingress test
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae2217 ("bpf: selftest: Add test_btf_skc_cls_ingress") Reported-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com
selftest/bpf: Add a test that reads various addresses.
Add a function to bpf_testmod that returns invalid kernel and user addresses.
Then attach an fexit program to that function that tries to read
memory through these addresses.
This logic checks that bpf_probe_read_kernel and BPF_PROBE_MEM logic is sane.
Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The verifier checks that PTR_TO_BTF_ID pointer is either valid or NULL,
but it cannot distinguish IS_ERR pointer from valid one.
When offset is added to IS_ERR pointer it may become small positive
value which is a user address that is not handled by extable logic
and has to be checked for at the runtime.
Tighten BPF_PROBE_MEM pointer check code to prevent this case.
Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Reported-by: Lorenzo Fontana <lorenzo.fontana@elastic.co> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The prog - start_of_ldx is the offset before the faulting ldx to the location
after it, so this will be used to adjust pt_regs->ip for jumping over it and
continuing, and with old temp it would have been fixed up to the wrong offset,
causing crash.
Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 16 Dec 2021 19:48:59 +0000 (11:48 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"A single fix for the clk framework that needed some more bake time in
linux-next.
The problem is that two clks being registered at the same time can
lead to a busted clk tree if the parent isn't fully registered by the
time the child finds the parent. We rejigger the place where we mark
the parent as fully registered so that the child can't find the parent
until things are proper"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Don't parent clks until the parent is fully registered
Daniel Borkmann [Wed, 15 Dec 2021 22:28:48 +0000 (22:28 +0000)]
bpf: Make 32->64 bounds propagation slightly more robust
Make the bounds propagation in __reg_assign_32_into_64() slightly more
robust and readable by aligning it similarly as we did back in the
__reg_combine_64_into_32() counterpart. Meaning, only propagate or
pessimize them as a smin/smax pair.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann [Wed, 15 Dec 2021 22:02:19 +0000 (22:02 +0000)]
bpf: Fix signed bounds propagation after mov32
For the case where both s32_{min,max}_value bounds are positive, the
__reg_assign_32_into_64() directly propagates them to their 64 bit
counterparts, otherwise it pessimises them into [0,u32_max] universe and
tries to refine them later on by learning through the tnum as per comment
in mentioned function. However, that does not always happen, for example,
in mov32 operation we call zext_32_to_64(dst_reg) which invokes the
__reg_assign_32_into_64() as is without subsequent bounds update as
elsewhere thus no refinement based on tnum takes place.
Thus, not calling into the __update_reg_bounds() / __reg_deduce_bounds() /
__reg_bound_offset() triplet as we do, for example, in case of ALU ops via
adjust_scalar_min_max_vals(), will lead to more pessimistic bounds when
dumping the full register state:
Technically, the smin_value=0 and smax_value=4294967295 bounds are not
incorrect, but given the register is still a constant, they break assumptions
about const scalars that smin_value == smax_value and umin_value == umax_value.
Without the smin_value == smax_value and umin_value == umax_value invariant
being intact for const scalars, it is possible to leak out kernel pointers
from unprivileged user space if the latter is enabled. For example, when such
registers are involved in pointer arithmtics, then adjust_ptr_min_max_vals()
will taint the destination register into an unknown scalar, and the latter
can be exported and stored e.g. into a BPF map value.
Fixes: 3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking") Reported-by: Kuee K1r0a <liulin063@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Thu, 16 Dec 2021 18:44:20 +0000 (10:44 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix missing error code on kexec failure path"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec: Fix missing error code 'ret' warning in load_other_segments()
Linus Torvalds [Thu, 16 Dec 2021 18:05:49 +0000 (10:05 -0800)]
Merge tag 'for-5.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix use after free in DM btree remove's rebalance_children()
- Fix DM integrity data corruption, introduced during 5.16 merge, due
to improper use of bvec_kmap_local()
* tag 'for-5.16/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm integrity: fix data corruption due to improper use of bvec_kmap_local
dm btree remove: fix use after free in rebalance_children()
Return code is not set to an error code in load_other_segments() when
of_kexec_alloc_and_setup_fdt() call returns a NULL dtb. This results
in status success (return code set to 0) being returned from
load_other_segments().
Set return code to -EINVAL if of_kexec_alloc_and_setup_fdt() returns
NULL dtb.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com> Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()") Link: https://lore.kernel.org/r/20211210010121.101823-1-nramas@linux.microsoft.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
David Howells [Tue, 14 Dec 2021 09:22:12 +0000 (09:22 +0000)]
afs: Fix mmap
Fix afs_add_open_map() to check that the vnode isn't already on the list
when it adds it. It's possible that afs_drop_open_mmap() decremented
the cb_nr_mmap counter, but hadn't yet got into the locked section to
remove it.
Also vnode->cb_mmap_link should be initialised, so fix that too.
Fixes: 6e0e99d58a65 ("afs: Fix mmap coherency vs 3rd-party changes") Reported-by: kafs-testing+fedora34_64checkkafs-build-300@auristor.com Suggested-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: kafs-testing+fedora34_64checkkafs-build-300@auristor.com
cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/686465.1639435380@warthog.procyon.org.uk/ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Wed, 15 Dec 2021 20:24:49 +0000 (12:24 -0800)]
net: systemport: Add global locking for descriptor lifecycle
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
D. Wythe [Wed, 15 Dec 2021 12:29:21 +0000 (20:29 +0800)]
net/smc: Prevent smc_release() from long blocking
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e658 ("net/smc: rebuild nonblocking connect") Reported-by: Tony Lu <tonylu@linux.alibaba.com> Tested-by: Dust Li <dust.li@linux.alibaba.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bryan O'Donoghue [Tue, 14 Dec 2021 13:46:30 +0000 (13:46 +0000)]
wcn36xx: Implement beacon filtering
The prima driver facilitates the direct programming of beacon filter tables via
SMD commands.
The purpose of beacon filters is quote:
/* When beacon filtering is enabled, firmware will
* analyze the selected beacons received during BMPS,
* and monitor any changes in the IEs as listed below.
* The format of the table is:
* - EID
* - Check for IE presence
* - Byte offset
* - Byte value
* - Bit Mask
* - Byte reference
*/
The default filter table looks something like this:
Add in an equivalent filter set as present in the prima Linux driver.
For now omit the beacon filter "rem" command as the driver does not have an
explicit call to that SMD command. The filter mask should only count when
we are inside BMPS anyway.
Replicating the ability to program the filter table gives us scope to add and
remove elements in future. For now though this patch makes the rote-copy of the
downstream Linux beacon filter table, which we can tweak as desired from now
on.
Bryan O'Donoghue [Tue, 14 Dec 2021 13:46:29 +0000 (13:46 +0000)]
wcn36xx: Fix physical location of beacon filter comment
The comment in the header with respect to beacon filtering makes a
reference to "the structure above" and "the structure below" which would be
informative if the comment appeared in the right place but, it does not.
Fix the comment location so that it a least makes sense w/r/t the physical
location statements.
Bryan O'Donoghue [Tue, 14 Dec 2021 13:46:28 +0000 (13:46 +0000)]
wcn36xx: Fix beacon filter structure definitions
The beacon filter structures need to be packed. Right now its fine because
we don't yet use these structures so just pack them without marking it for
backporting.
Anilkumar Kolli [Tue, 14 Dec 2021 15:39:43 +0000 (17:39 +0200)]
ath11k: Use reserved host DDR addresses from DT for PCI devices
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2)
is reserved through DT entries for firmware usage. Send the base
address from DT entries.
If DT entry is available, PCI device will work with
fixed_mem_region else host allocates multiple segments.
IPQ8074 on HK10 board supports multiple PCI devices.
IPQ8074 + QCN9074 is tested with this patch.
Anilkumar Kolli [Tue, 14 Dec 2021 15:39:43 +0000 (17:39 +0200)]
dt: bindings: add new DT entry for ath11k PCI device support
Ath11k driver supports PCI devices such as QCN9074/QCA6390.
Ath11k firmware uses host DDR memory, DT entry is used to
reserve host DDR memory regions, send these memory base
addresses using DT entries.
Jakub Kicinski [Thu, 16 Dec 2021 15:18:39 +0000 (07:18 -0800)]
Merge branch 'fib-merge-nl-policies'
Florian Westphal says:
====================
fib: merge nl policies
v4: resend with fixed subject line. I preserved review tags
from David Ahern.
v3: drop first two patches, otherwise unchanged.
This series merges the different (largely identical) nla policies.
v2 also squashed the ->suppress() implementation, I've dropped this.
Problem is that it needs ugly ifdef'ry to avoid build breakage
with CONFIG_INET=n || IPV6=n.
Given that even microbenchmark doesn't show any noticeable improvement
when ->suppress is inlined (it uses INDIRECT_CALLABLE) i decided to toss
the patch instead of adding more ifdefs.
====================
Gal Pressman [Thu, 16 Dec 2021 09:28:25 +0000 (11:28 +0200)]
net: Fix double 0x prefix print in SKB dump
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc64 ("skbuff: increase verbosity when dumping skb data") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wenliang Wang [Thu, 16 Dec 2021 03:11:35 +0000 (11:11 +0800)]
virtio_net: fix rx_drops stat for small pkts
We found the stat of rx drops for small pkts does not increment when
build_skb fail, it's not coherent with other mode's rx drops stat.
Signed-off-by: Wenliang Wang <wangwenliang.1995@bytedance.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Eremeev [Wed, 15 Dec 2021 17:30:32 +0000 (20:30 +0300)]
dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED
Debug print uses invalid check to detect if speed is unforced:
(speed != SPEED_UNFORCED) should be used instead of (!speed).
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Andrey Eremeev <Axtone4all@yandex.ru> Fixes: 96a2b40c7bd3 ("net: dsa: mv88e6xxx: add port's MAC speed setter") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiasheng Jiang [Wed, 15 Dec 2021 14:37:31 +0000 (22:37 +0800)]
sfc_ef100: potential dereference of null pointer
The return value of kmalloc() needs to be checked.
To avoid use in efx_nic_update_stats() in case of the failure of alloc.
Fixes: b593b6f1b492 ("sfc_ef100: statistics gathering") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Volodymyr Mytnyk [Wed, 15 Dec 2021 10:07:30 +0000 (12:07 +0200)]
net: prestera: flower template support
Add user template explicit support. At this moment, max
TCAM rule size is utilized for all rules, doesn't matter
which and how much flower matches are provided by user. It
means that some of TCAM space is wasted, which impacts
the number of filters that can be offloaded.
Introducing the template, allows to have more HW offloaded
filters by specifying the template explicitly.
Example:
tc qd add dev PORT clsact
tc chain add dev PORT ingress protocol ip \
flower dst_ip 0.0.0.0/16
tc filter add dev PORT ingress protocol ip \
flower skip_sw dst_ip 1.2.3.4/16 action drop
NOTE: chain 0 is the default chain id for "tc chain" & "tc filter"
command, so it is omitted in the example above.
This patch adds only template support for default chain 0 suppoerted
by prestera driver at this moment. Chains are not supported yet,
and will be added later.
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
realtek-smi switch: phy mode gmii is unsupported on port 0
realtek-smi switch lan5 (uninitialized): validation of gmii with
support 0000000,00000000,000062ef and advertisement 0000000,00000000,000062ef failed: -22
realtek-smi switch lan5 (uninitialized): failed to connect to PHY:
-EINVAL
realtek-smi switch lan5 (uninitialized): error -22 setting up PHY
for tree 1, switch 0, port 0
I also noticed the same issue before with older versions but using
a MDIO interface driver, not realtek-smi.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Keeping [Tue, 14 Dec 2021 19:10:09 +0000 (19:10 +0000)]
net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup
KASAN reports an out-of-bounds read in rk_gmac_setup on the line:
while (ops->regs[i]) {
This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here. It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.
To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.
Fixes: 3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support") Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Dec 2021 10:41:54 +0000 (10:41 +0000)]
Merge branch 'gve-improvements'
Jeroen de Borst says:
====================
gve improvements
This patchset consists of unrelated changes:
A bug fix for an issue that disabled jumbo-frame support, a few code
improvements and minor funcitonal changes and 3 new features:
Supporting tx|rx-coalesce-usec for DQO
Suspend/resume/shutdown
Optional metadata descriptors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 16 Dec 2021 00:46:49 +0000 (16:46 -0800)]
gve: Add optional metadata descriptor type GVE_TXD_MTD
Allow drivers to pass metadata along with packet data to the device.
Introduce a new metadata descriptor type
* GVE_TXD_MTD
This descriptor is optional. If present it immediate follows the
packet descriptor and precedes the segment descriptor.
This descriptor may be repeated. Multiple metadata descriptors may
follow. There are no immediate uses for this, this is for future
proofing. At present devices allow only 1 MTD descriptor.
The lower four bits of the type_flags field encode GVE_TXD_MTD.
The upper four bits of the type_flags field encodes a *sub*type.
Introduce one such metadata descriptor subtype
* GVE_MTD_SUBTYPE_PATH
This shares path information with the device for network failure
discovery and robust response:
Linux derives ipv6 flowlabel and ECMP multipath from sk->sk_txhash,
and updates this field on error with sk_rethink_txhash. Allow the host
stack to do the same. Pass the tx_hash value if set. Also communicate
whether the path hash is set, or more exactly, what its type is. Define
two common types
GVE_MTD_PATH_HASH_NONE
GVE_MTD_PATH_HASH_L4
Concrete examples of error conditions that are resolved are
mentioned in the commits that add sk_rethink_txhash calls. Such as
commit 7788174e8726 ("tcp: change IPv6 flow-label upon receiving
spurious retransmission").
Experimental results mirror what the theory suggests: where IPv6
FlowLabel is included in path selection (e.g., LAG/ECMP), flowlabel
rotation on TCP timeout avoids the vast majority of TCP disconnects
that would otherwise have occurred during link failures in long-haul
backbones, when an alternative path is available.
Rotation can be applied to various bad connection signals, such as
timeouts and spurious retransmissions. In aggregate, such flow level
signals can help locate network issues. Define initial common states:
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
gve: Move the irq db indexes out of the ntfy block struct
Giving the device access to other kernel structs is not ideal.
Move the indexes into their own array and just keep pointers to
them in the ntfy block struct.
Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeroen de Borst [Thu, 16 Dec 2021 00:46:45 +0000 (16:46 -0800)]
gve: Correct order of processing device options
The legacy raw addressing device option was processed before the
new RDA queue format option. This caused the supported features mask,
which is provided only on the RDA queue format option, not to be set.
This disabled jumbo-frame support when using raw adressing.
Fixes: 255489f5b33c ("gve: Add a jumbo-frame device option") Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series allows phylink to include the PCS in its validation step.
There are two reasons to make this change:
1. Some of the network drivers that are making use of the split PCS
support are already manually calling into their PCS drivers to
perform validation. E.g. stmmac with xpcs.
2. Logically, some network drivers such as mvneta and mvpp2, the
restriction we impose in the validate() callback is a property of
the "PCS" block that we provide rather than the MAC.
This series:
1. Gives phylink a mechanism to query the MAC driver which PCS is
wishes to use for the PHY interface mode. This is necessary to allow
the PCS to be involved in the validation step without making changes
to the configuration.
2. Provide a pcs_validate() method that PCS can implement. This follows
a similar model to the MAC's validate() callback, but with some minor
differences due to observations from the various implementations.
E.g. returning an error code for not-supported and the way the
advertising bitmap is masked.
3. Convert mvpp2 and mvneta to this as examples of its use. Further
Conversions are in the pipeline, including for stmmac+xpcs, as well
as some DSA drivers. Note that DSA conversion to this is conditional
upon all DSA drivers populating their supported_interfaces bitmap,
since this is required before mac_select_pcs() can be used.
Existing drivers that set a PCS in mac_prepare() or mac_config(), or
shortly after phylink_create() will continue to work. However, it should
be noted that mac_select_pcs() will be called during phylink_create(),
and thus any PCS returned by mac_select_pcs() must be available by this
time - or we drop the check in phylink_create().
v2: fix kerneldoc typo in patch 1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvneta: convert to pcs_validate() and phylink_generic_validate()
Convert mvneta to validate the autoneg state for 1000base-X in the
pcs_validate() operation, rather than the MAC validate() operation.
This allows us to switch the MAC validate() to use
phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: convert to pcs_validate() and phylink_generic_validate()
Convert mvpp2 to validate the autoneg state for 1000base-X in the
pcs_validate() operation, rather than the MAC validate() operation.
This allows us to switch the MAC validate() to use
phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook for PCS to validate the link parameters. This avoids MAC
drivers having to have knowledge of their PCS in their validate()
method, thereby allowing several MAC drivers to be simplfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phylink: add mac_select_pcs() method to phylink_mac_ops
mac_select_pcs() allows us to have an explicit point to query which
PCS the MAC wishes to use for a particular PHY interface mode, thereby
allowing us to add support to validate the link settings with the PCS.
Phylink will also use this to select the PCS to be used during a major
configuration event without the MAC driver needing to call
phylink_set_pcs().
Note that if mac_select_pcs() is present, the supported_interfaces
bitmap must be filled in; this avoids mac_select_pcs() being called
with PHY_INTERFACE_MODE_NA when we want to get support for all
interface types. Phylink will return an error in phylink_create()
unless this condition is satisfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Dec 2021 10:23:34 +0000 (10:23 +0000)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/nex
t-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-12-15
This series contains updates to ice driver only.
Jake makes changes to flash update. This includes the following:
* a new shadow-ram region similar to NVM region but for the device shadow
RAM contents. This is distinct from NVM region because shadow RAM is
built up during device init and may be different from the raw NVM flash
data.
* refactoring of the ice_flash_pldm_image to become the main flash update
entry point. This is simpler than having both an
ice_devlink_flash_update and an ice_flash_pldm_image. It will make
additions like dry-run easier in the future.
* reducing time to read Option ROM version information.
* adding support for firmware activation via devlink reload, when
possible.
The major new work is the reload support, which allows activating firmware
immediately without a reboot when possible. Reload support only supports
firmware activation.
Jesse improves transmit code: utilizing newer netif_tx* API, adding some
prefetch calls, correcting expected conditions when calling ice_vsi_down(),
and utilizing __netdev_tx_sent_queue() call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Dec 2021 10:22:20 +0000 (10:22 +0000)]
Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-next branch 2021-12-15
Hi Dave, Jakub, Jason
This pulls mlx5-next branch into net-next and rdma branches.
All patches already reviewed on both rdma and netdev mailing lists.
Please pull and let me know if there's any problem.
1) Add multiple FDB steering priorities [1]
2) Introduce HW bits needed to configure MAC list size of VF/SF.
Required for ("net/mlx5: Memory optimizations") upcoming series [2].
wilc1000: Improve WILC TX performance when power_save is off
The wakeup and sleep commands need to be sent to the WILC chip only
when it is in power save mode (PSM, as controlled by "iw dev wlan0 set
power_save on/off"). The commands are relatively costly, so it pays
to skip them when possible.
iperf3 without this patch (no significant different with PSM on/off):
TX 0.00-120.01 sec 140 MBytes 9.82 Mbits/sec
RX 0.00-120.69 sec 283 MBytes 19.6 Mbits/sec
with this patch applied:
PSM off (TX is 46% improved, RX slightly improved; may not be significant):
TX 0.00-120.00 sec 206 MBytes 14.4 Mbits/sec
RX 0.00-120.48 sec 322 MBytes 22.4 Mbits/sec
PSM on (no significant change):
TX 0.00-120.00 sec 140 MBytes 9.78 Mbits/sec
RX 0.00-120.08 sec 257 MBytes 18.0 Mbits/sec
Merlijn Wajer [Sun, 12 Dec 2021 22:13:08 +0000 (23:13 +0100)]
wl1251: specify max. IE length
This fix is similar to commit 77c91295ea53 ("wil6210: specify max. IE
length"). Without the max IE length set, wpa_supplicant cannot operate
using the nl80211 interface.
This patch is a workaround - the number 512 is taken from the wlcore
driver, but note that per Paul Fertser:
there's no correct number because the driver will ignore the data
passed in extra IEs.
Kalle Valo [Thu, 16 Dec 2021 08:25:12 +0000 (10:25 +0200)]
Merge tag 'iwlwifi-next-for-kalle-2021-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
first set of iwlwifi patches for v5.17
* A few mei fixes;
* Some improvements in D3;
* Support for new FW API commands;
* Fixes and cleanups in device configurations;
* Support some new FW API command versions;
* Fix WGDS revision 3 reading bug;
* Some firmware debugging improvements;
* Fixes for in device configuration structures;
* Improvements in the session protection code;
* Support SAR GEO Offset Mapping (SGOM) via BIOS;
* Continued work on the new Bz device family;
* Some more firmware debugging improvements;
* Support new FW API version 68;
* Add some new device IDs;
* Some other small fixes, clean-ups and improvements.
projects / mirror_ubuntu-kernels.git / log