Petri Gynther [Thu, 9 May 2013 16:50:00 +0000 (16:50 +0000)]
emac: Fix EMAC soft reset on 460EX/GT
Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.
EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.
PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.
Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).
With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 9 May 2013 11:14:07 +0000 (11:14 +0000)]
3c59x: fix PCI resource management
The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address. Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `cfv_destroy_genpool':
drivers/net/caif/caif_virtio.c:364: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `cfv_create_genpool':
drivers/net/caif/caif_virtio.c:397: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `xgmac_xmit':
drivers/net/ethernet/calxeda/xgmac.c:1102: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
I'm using following script to trigger this:
<script>
while [ 1 ]
do
ip link add link e1 name macvtap0 type macvtap mode passthru
ip link set e1 up
ip link set macvtap0 up
IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
cat /dev/tap$IFINDEX >/dev/null &
ip link del dev macvtap0
done
</script>
I run this script while "ping -f" is running on another machine to send
packets to e1 rx.
Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.
I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.
Introduced by: commit eb06acdc85585f2 "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 May 2013 23:23:44 +0000 (16:23 -0700)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>
Rony Efraim [Wed, 8 May 2013 22:22:35 +0000 (22:22 +0000)]
net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
Make sure that the following steps are taken:
- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set
Use enum values for all the above instead of numerical bit offsets.
Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 8 May 2013 22:22:34 +0000 (22:22 +0000)]
net/mlx4_core: Add missing report on VST and spoof-checking dev caps
Commits e6b6a23 "net/mlx4: Add VF MAC spoof checking support" and 3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shawn Guo [Wed, 8 May 2013 21:08:22 +0000 (21:08 +0000)]
net: fec: enable hardware checksum only on imx6q-fec
Commit 4c09eed (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants. This is inappropriate, because some variants like imx5 have
no such support on hardware. Consequently, fec is broken on these
platforms. Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Jim Baxter <jim_baxter@mentor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 May 2013 23:01:23 +0000 (16:01 -0700)]
Merge branch 'qlcnic'
Shahed Shaikh says:
====================
This patch series has following bug fixes:
* Fix a bug in unicast MAC address setting in adapter.
Driver was not deleting older unicast MAC while adding new one.
* Fix an ethtool stats string array by adding missing string entry
and fix a typo.
* Fix module paramter description. Bracket ')' was missing.
* Fix port status provided though 'ethtool <device>' for 83xx adapter.
* Fix reset recovery path in case of transmit timeout.
* Fix reset recovery during diagnostic tests by preserving
current device status information.
* Fix mailbox response handling. Driver was not maintaining poll time properly.
* Fix validation of link event command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rajesh Borundia [Thu, 9 May 2013 09:25:15 +0000 (09:25 +0000)]
qlcnic: Fix mailbox response handling.
o Fix mailbox response poll time to maximum 5 seconds which
includes mailbox response time as well as time required for
processing AEN if any.
o Driver need to read firmware control mailbox register instead
of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 9 May 2013 09:25:14 +0000 (09:25 +0000)]
qlcnic: Fix bug in diagnostics test reset recovery path
o In order to perform reset recovery during diagnostics tests,
current device status information need to be preserved.
This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Thu, 9 May 2013 09:25:13 +0000 (09:25 +0000)]
qlcnic: Fix reset recovery after transmit timeout
o When transmit timeout happens, recovery attempt should start with
adapter soft reset. If soft reset fails to resume traffic, firmware
dump will be collected and driver will perform a hard reset of the
adapter. Reset recovery on 83xx was failing after a hard reset.
This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: Fix ethtool supported port status for 83xx
o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 9 May 2013 09:25:09 +0000 (09:25 +0000)]
qlcnic: Fix setting MAC address
o Delete previous unicast MAC which is already programmed
in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 May 2013 16:44:05 +0000 (09:44 -0700)]
Merge branch 'wireless'
John W. Linville says:
====================
Here is a batch of fixes intended for the 3.10 stream.
Amitkumar Karwar provides an mwifiex fix to plug a memory leak when
the driver is unloaded.
Bing Zhao brings an mwifiex fix for some flag handling that leads to
log spam and an unusable interface.
Daniel Drake offers an mwifiex fix for multicast filter setup, to
correctly implement wakeup behaviour for multicast WOL.
Felix Fietkau fixes an ath9k problem that produces logspam and keycache
errors due to a bad return code.
Stanislaw Gruszka produces an fix for a WARNING from ath5k, and an
iwl4965 workaround to stop advertising a feature that doesn't work with
the current mac80211 implementation.
Sujith Manoharan gives us an ath9k fix to reprogram the HW beacon timers
after a TSF update, and an initvals fix for the AR9565 device.
Thommy Jakobsson fixes an rx descriptor underrun on b43.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 9 May 2013 23:42:10 +0000 (16:42 -0700)]
Merge tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull trivial pstore update from Tony Luck:
"Couple of pstore cleanups"
It turns out that the kmemdup() conversion ends up being undone by the
fact that the memory block also needed the ecc information (see commit bd08ec33b5c2: "pstore/ram: Restore ecc information block"), so all that
remains after merging is the error return code change.
* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore/ram: fix error return code in ramoops_probe()
fs: pstore: Replaced calls to kmalloc and memcpy with kmemdup
Pull NVMe driver update from Matthew Wilcox:
"Lots of exciting new features in the NVM Express driver this time,
including support for emulating SCSI commands, discard support and the
ability to submit per-sector metadata with I/Os.
It's still mostly bugfixes though!"
* git://git.infradead.org/users/willy/linux-nvme: (27 commits)
NVMe: Use user defined admin ioctl timeout
NVMe: Simplify Firmware Activate code slightly
NVMe: Only clear the enable bit when disabling controller
NVMe: Wait for device to acknowledge shutdown
NVMe: Schedule timeout for sync commands
NVMe: Meta-data support in NVME_IOCTL_SUBMIT_IO
NVMe: Device specific stripe size handling
NVMe: Split non-mergeable bio requests
NVMe: Remove dead code in nvme_dev_add
NVMe: Check for NULL memory in nvme_dev_add
NVMe: Fix error clean-up on nvme_alloc_queue
NVMe: Free admin queue on request_irq error
NVMe: Add scsi unmap to SG_IO
NVMe: queue usage fixes in nvme-scsi
NVMe: Set TASK_INTERRUPTIBLE before processing queues
NVMe: Add a character device for each nvme device
NVMe: Fix endian-related problems in user I/O submission path
NVMe: Fix I/O cancellation status on big-endian machines
NVMe: Fix sparse warnings in scsi emulation
NVMe: Don't fail initialisation unnecessarily
...
Linus Torvalds [Thu, 9 May 2013 23:33:42 +0000 (16:33 -0700)]
Merge tag 'acpi-fixes-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA fixes from Rafael Wysocki:
- _INI regression fix from Tomasz Nowicki.
- Fix for a possible memory leak in _OSI support routine from Jung-uk
Kim.
- Fix for a possible buffer overflow during field unit read operation
from Bob Moore.
* tag 'acpi-fixes-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: ACPICA: Fix for _INI regression
ACPICA: _OSI support: Fix possible memory leak
ACPICA: Fix possible buffer overflow during a field unit read operation
Linus Torvalds [Thu, 9 May 2013 21:54:36 +0000 (14:54 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes and straggler patches from Olof Johansson:
"A collection of fixes for fall out from 3.10 merge window, some build
fixes and warning cleanups and a small handful of patches that were
small and contained and made sense to still include in 3.10 (some of
these have also been in -next since the merge window opened).
Largest continous series is for OMAP, but there's a handful for other
platforms.
For i.MX, one of the patches are framebuffer fixups due to fallout
during the merge window, and the other removes some stale and broken
code."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: dts: Fixed vbus-gpios
ARM: EXYNOS5: Fix kernel dump in AFTR idle mode
ARM: ux500: Rid ignored return value of regulator_enable() compiler warning
ARM: ux500: read the correct soc_id number
ARM: exynos: dts: cros5250: add cyapa trackpad
video: mxsfb: Adapt to new videomode API
ARM: imx: Select GENERIC_ALLOCATOR
ARM: imx: compile fix for hotplug.c
ARM: dts: don't assume boards are using twl4030 for omap3
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: dts: Configure and fix the McSPI pins for 4430sdp
ARM: dts: AM33XX: Add GPMC node
ARM: dts: OMAP4460: Fix CPU OPP voltages
ARM: dts: OMAP36xx: Fix CPU OPP voltages
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
...
Linus Torvalds [Thu, 9 May 2013 21:38:16 +0000 (14:38 -0700)]
Merge tag 'xtensa-next-20130508' of git://github.com/czankel/xtensa-linux
Pull xtensa updates from Chris Zankel:
"Support for the latest MMU architecture that allows for a larger
accessible memory region, and various bug-fixes"
* tag 'xtensa-next-20130508' of git://github.com/czankel/xtensa-linux:
xtensa: Switch to asm-generic/linkage.h
xtensa: fix redboot load address
xtensa: ISS: fix timer_lock usage in rs_open
xtensa: disable IRQs while IRQ handler is running
xtensa: enable lockdep support
xtensa: fix arch_irqs_disabled_flags implementation
xtensa: add irq flags trace support
xtensa: provide custom CALLER_ADDR* implementations
xtensa: add stacktrace support
xtensa: clean up stpill_registers
xtensa: don't use a7 in simcalls
xtensa: don't attempt to use unconfigured timers
xtensa: provide default platform_pcibios_init implementation
xtensa: remove KCORE_ELF again
xtensa: document MMUv3 setup sequence
xtensa: add MMU v3 support
xtensa: fix ibreakenable register update
xtensa: fix oprofile building as module
Linus Torvalds [Thu, 9 May 2013 21:36:27 +0000 (14:36 -0700)]
Merge tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC port updates from Vineet Gupta:
"Support for two new platforms based on ARC700:
- Abilis TB10x SoC [Chritisian/Pierrick]
- Simulator only System-C Model [Mischa]
ARC specific MM improvements:
- Avoid full TLB flush (ASID increment) on munmap (even single page)
- VIPT Cache Flushing improvements
+ Delayed dcache flush for non-aliasing dcache (big performance boost)
+ icache flush aliasing agnostic (no need to kill all possible aliases)
Others:
- Avoid needless rebuild of DTB files for every kernel build
- Remove builtin cmdline as that is already provided by DeviceTree/bootargs
- Fixing unaligned access emulation corner case
- checkpatch fixes [Sachin]
- Various fixlets [Noam]
- Minor build failures/cleanups"
* tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (35 commits)
ARC: [mm] Lazy D-cache flush (non aliasing VIPT)
ARC: [mm] micro-optimize page size icache invalidate
ARC: [mm] remove the pessimistic all-alias-invalidate icache helpers
ARC: [mm] consolidate icache/dcache sync code
ARC: [mm] optimise icache flush for kernel mappings
ARC: [mm] optimise icache flush for user mappings
ARC: [mm] optimize needless full mm TLB flush on munmap
ARC: Add support for nSIM OSCI System C model
ARC: [TB10x] Adapt device tree to new compatible string
ARC: [TB10x] Add support for TB10x platform
ARC: [TB10x] Device tree of TB100 and TB101 Development Kits
ARC: Prepare interrupt code for external controllers
ARC: Allow embedded arc-intc to be properly placed in DT intc hierarchy
ARC: [cmdline] Don't overwrite u-boot provided bootargs
ARC: [cmdline] Remove CONFIG_CMDLINE
ARC: [plat-arcfpga] defconfig update
ARC: unaligned access emulation broken if callee-reg dest of LD/ST
ARC: unaligned access emulation error handling consolidation
ARC: Debug/crash-printing Improvements
ARC: fix typo with clock speed
...
Linus Torvalds [Thu, 9 May 2013 21:34:58 +0000 (14:34 -0700)]
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull tile update from Chris Metcalf:
"The interesting bug fix is support for the upcoming "4.2" release of
the Tilera hypervisor, which by default launches Linux at privilege
level 2 instead of 1. The fix lets new and old hypervisors and
Linuxes interoperate more smoothly, so I've tagged it for
stable@kernel.org so that older Linuxes will be able to boot under the
newer hypervisor."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
usb: tilegx: fix memleak when create hcd fail
arch/tile: remove inline marking of EXPORT_SYMBOL functions
rtc: rtc-tile: add missing platform_device_unregister() when module exit
tile: support new Tilera hypervisor
Rik van Riel [Thu, 9 May 2013 20:59:59 +0000 (16:59 -0400)]
ipc,sem: fix semctl(..., GETNCNT)
The semctl GETNCNT returns the number of semops waiting for the
specified semaphore to become nonzero. After commit 9f1bc2c9022c
("ipc,sem: have only one list in struct sem_queue"), the semops waiting
on just one semaphore are waiting on that semaphore's list.
In order to return the correct count, we have to walk that list too, in
addition to the sem_array's list for complex operations.
Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Thu, 9 May 2013 20:53:28 +0000 (16:53 -0400)]
ipc,sem: fix semctl(..., GETZCNT)
The semctl GETZCNT returns the number of semops waiting for the
specified semaphore to become zero. After commit 9f1bc2c9022c
("ipc,sem: have only one list in struct sem_queue"), the semops waiting
on just one semaphore are waiting on that semaphore's list.
In order to return the correct count, we have to walk that list too, in
addition to the sem_array's list for complex operations.
This bug broke dbench; it works again with this patch applied.
Signed-off-by: Rik van Riel <riel@redhat.com> Reported-by: Kent Overstreet <koverstreet@google.com> Tested-by: Kent Overstreet <koverstreet@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doug Anderson [Wed, 8 May 2013 17:37:16 +0000 (10:37 -0700)]
ARM: exynos: dts: Fixed vbus-gpios
The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier. Fix the two
exynos5250 boards that use it.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Olof Johansson <olof@lixom.net>
The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.
This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Olof Johansson [Thu, 9 May 2013 20:14:02 +0000 (13:14 -0700)]
Merge tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap device tree fixes for issue discovered during the merge window:
- Fix triggering for GPIO interrupts that's needed for 4430sdp
Ethernet. Otherwise booting with nfsroot won't work.
- Fix CPU operating point values
- Fix wrong assumption that twl PMIC is always connected to omap3
- Add gpmc for am33xx so beaglebone users can use the bus
- Cosmetic fix for mcspi pin muxing to avoid confusion
* tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: don't assume boards are using twl4030 for omap3
ARM: dts: Configure and fix the McSPI pins for 4430sdp
ARM: dts: AM33XX: Add GPMC node
ARM: dts: OMAP4460: Fix CPU OPP voltages
ARM: dts: OMAP36xx: Fix CPU OPP voltages
ARM: dts: OMAP4: Fix ethernet IRQ for OMAP4 boards
Olof Johansson [Thu, 9 May 2013 20:12:31 +0000 (13:12 -0700)]
Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:
- Few GPMC fixes and binding doc updates noted after sending
pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
handling fixes
Then few minor things that are not strictly fixes but are good
to get out of the way:
- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig
* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
omap: mux: add AM/DM37x gpios
ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
ARM: OMAP2+: omap_device: use late_initcall_sync
ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
ARM: OMAP2+: only WARN if a GPMC child probe function fail
ARM: OMAP2+: only search for GPMC DT child nodes on probe
Documentation: dt: update properties in TI GPMC NAND example
Documentation: dt: update TI GPMC ethernet binding properties
Lee Jones [Thu, 2 May 2013 15:48:07 +0000 (16:48 +0100)]
ARM: ux500: Rid ignored return value of regulator_enable() compiler warning
arch/arm/mach-ux500/board-mop500.c: In function ‘mop500_prox_activate’:
arch/arm/mach-ux500/board-mop500.c:406:18: warning: ignoring return value of
‘regulator_enable’, declared with attribute warn_unused_result
[-Wunused-result]
Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Thu, 9 May 2013 20:07:40 +0000 (13:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs update from Chris Mason:
"These are mostly fixes. The biggest exceptions are Josef's skinny
extents and Jan Schmidt's code to rebuild our quota indexes if they
get out of sync (or you enable quotas on an existing filesystem).
The skinny extents are off by default because they are a new variation
on the extent allocation tree format. btrfstune -x enables them, and
the new format makes the extent allocation tree about 30% smaller.
I rebased this a few days ago to rework Dave Sterba's crc checks on
the super block, but almost all of these go back to rc6, since I
though 3.9 was due any minute.
The biggest missing fix is the tracepoint bug that was hit late in
3.9. I ran into problems with that in overnight testing and I'm still
tracking it down. I'll definitely have that fixed for rc2."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (101 commits)
Btrfs: allow superblock mismatch from older mkfs
btrfs: enhance superblock checks
btrfs: fix misleading variable name for flags
btrfs: use unsigned long type for extent state bits
Btrfs: improve the loop of scrub_stripe
btrfs: read entire device info under lock
btrfs: remove unused gfp mask parameter from release_extent_buffer callchain
btrfs: handle errors returned from get_tree_block_key
btrfs: make static code static & remove dead code
Btrfs: deal with errors in write_dev_supers
Btrfs: remove almost all of the BUG()'s from tree-log.c
Btrfs: deal with free space cache errors while replaying log
Btrfs: automatic rescan after "quota enable" command
Btrfs: rescan for qgroups
Btrfs: split btrfs_qgroup_account_ref into four functions
Btrfs: allocate new chunks if the space is not enough for global rsv
Btrfs: separate sequence numbers for delayed ref tracking and tree mod log
btrfs: move leak debug code to functions
Btrfs: return free space in cow error path
Btrfs: set UUID in root_item for created trees
...
Linus Torvalds [Thu, 9 May 2013 20:06:20 +0000 (13:06 -0700)]
Merge tag 'for-linus-v3.10-rc1-2' of git://oss.sgi.com/xfs/xfs
Pull xfs update (#2) from Ben Myers:
- add CONFIG_XFS_WARN, a step between zero debugging and
CONFIG_XFS_DEBUG.
- fix attrmulti and attrlist to fall back to vmalloc when kmalloc
fails.
* tag 'for-linus-v3.10-rc1-2' of git://oss.sgi.com/xfs/xfs:
xfs: fallback to vmalloc for large buffers in xfs_compat_attrlist_by_handle
xfs: fallback to vmalloc for large buffers in xfs_attrlist_by_handle
xfs: introduce CONFIG_XFS_WARN
Fabio Estevam [Wed, 8 May 2013 13:05:55 +0000 (21:05 +0800)]
video: mxsfb: Adapt to new videomode API
commit 6cd2c7db4 (videomode: videomode_from_timing work) changed the name of
the function from videomode_from_timing() to videomode_from_timings().
commit 32ed6ef1 (videomode: create enum for videomode's display flags) changed
the 'data_flags' field in videomode structure to 'flags'
Adapt to these changes in order to fix the following errors:
drivers/video/mxsfb.c:761:3: error: too many arguments to function 'videomode_from_timing'
drivers/video/mxsfb.c:761:7: error: void value not ignored as it ought to be
drivers/video/mxsfb.c:768:9: error: 'struct videomode' has no member named 'data_flags'
drivers/video/mxsfb.c:770:9: error: 'struct videomode' has no member named 'data_flags'
Also, select VIDEOMODE_HELPER instead of OF_VIDEOMODE, as this one is
deprecated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Fabio Estevam [Wed, 8 May 2013 13:05:54 +0000 (21:05 +0800)]
ARM: imx: Select GENERIC_ALLOCATOR
Since commit 657eee7 (media: coda: use genalloc API) the following build
error happens with imx_v4_v5_defconfig:
drivers/built-in.o: In function 'coda_remove':
clk-composite.c:(.text+0x112180): undefined reference to 'gen_pool_free'
drivers/built-in.o: In function 'coda_probe':
clk-composite.c:(.text+0x112310): undefined reference to 'of_get_named_gen_pool'
clk-composite.c:(.text+0x1123f4): undefined reference to 'gen_pool_alloc'
clk-composite.c:(.text+0x11240c): undefined reference to 'gen_pool_virt_to_phys'
clk-composite.c:(.text+0x112458): undefined reference to 'dev_get_gen_pool'
Select GENERIC_ALLOCATOR and get rid of the custom IRAM_ALLOC.
Shawn Guo [Wed, 8 May 2013 13:05:53 +0000 (21:05 +0800)]
ARM: imx: compile fix for hotplug.c
Commit bca7a5a (ARM: cpu hotplug: remove majority of cache flushing
from platforms) removes include of <asm/cacheflush.h> and hence
discovers a few indirect inclusion and declaration problems as below.
CC arch/arm/mach-imx/hotplug.o
In file included from arch/arm/mach-imx/hotplug.c:16:0:
arch/arm/mach-imx/common.h:100:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/common.h:100:29: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/arm/mach-imx/common.h:101:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_die’:
arch/arm/mach-imx/hotplug.c:53:2: error: implicit declaration of function ‘cpu_do_idle’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_kill’:
arch/arm/mach-imx/hotplug.c:58:26: error: ‘jiffies’ undeclared (first use in this function)
arch/arm/mach-imx/hotplug.c:58:26: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-imx/hotplug.c:58:2: error: implicit declaration of function ‘msecs_to_jiffies’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c:61:3: error: implicit declaration of function ‘time_after’ [-Werror=implicit-function-declaration]
Fix them by adding the needed inclusion and declaration.
Linus Torvalds [Thu, 9 May 2013 17:24:54 +0000 (10:24 -0700)]
Merge tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client bugfixes from Trond Myklebust:
- Ensure that we match the 'sec=' mount flavour against the server list
- Fix the NFSv4 byte range locking in the presence of delegations
- Ensure that we conform to the NFSv4.1 spec w.r.t. freeing lock
stateids
- Fix a pNFS data server connection race
* tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4.1 Fix data server connection race
NFSv3: match sec= flavor against server list
NFSv4.1: Ensure that we free the lock stateid on the server
NFSv4: Convert nfs41_free_stateid to use an asynchronous RPC call
SUNRPC: Don't spam syslog with "Pseudoflavor not found" messages
NFSv4.x: Fix handling of partially delegated locks
1) Propagate return error values properly in irda, spider_net, sfc, and
bfin_mac. From Wei Yongjun.
2) Fix fec driver OOPS on rapid link up/down, from Frank Li.
3) FIX VF resource allocation and chip message payload length errors in
be2net driver, from Sathya Perla.
4) Fix inner protocol inspection during GSO from Pravin B Shelar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
if_cablemodem.h: Add parenthesis around ioctl macros
gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()
net: fec: fix kernel oops when plug/unplug cable many times
bfin_mac: fix error return code in bfin_mac_probe()
sfc: fix return value check in efx_ptp_probe_channel()
net/spider_net: fix error return code in spider_net_open()
net/irda: fix error return code in bfin_sir_open()
net: of_mdio: fix behavior on missing phy device
sierra_net: keep status interrupt URB active
usbnet: allow status interrupt URB to always be active
qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN card
be2net: disable TX in be_close()
be2net: fix EQ from getting full while cleaning RX CQ
be2net: fix payload_len value for GET_MAC_LIST cmd req
be2net: provision VF resources before enabling SR-IOV
Linus Torvalds [Thu, 9 May 2013 17:21:44 +0000 (10:21 -0700)]
Merge tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"MSI:
PCI: Set ->mask_pos correctly
Hotplug:
PCI: Delay final fixups until resources are assigned
Moorestown:
x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"
* tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Delay final fixups until resources are assigned
x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
PCI: Set ->mask_pos correctly
arch/xtensa/platforms/iss/simdisk.c: In function 'proc_read_simdisk':
arch/xtensa/platforms/iss/simdisk.c:220:12: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
arch/xtensa/platforms/iss/simdisk.c: In function 'proc_write_simdisk':
arch/xtensa/platforms/iss/simdisk.c:241:38: error: 'buffer' undeclared (first use in this function)
arch/xtensa/platforms/iss/simdisk.c:241:38: note: each undeclared identifier is reported only once for each function it appears in
Linus Torvalds [Thu, 9 May 2013 17:15:46 +0000 (10:15 -0700)]
Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd
Pull MTD update from David Woodhouse:
- Lots of cleanups from Artem, including deletion of some obsolete
drivers
- Support partitions larger than 4GiB in device tree
- Support for new SPI chips
* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
mtd: omap2: Use module_platform_driver()
mtd: bf5xx_nand: Use module_platform_driver()
mtd: denali_dt: Remove redundant use of of_match_ptr
mtd: denali_dt: Change return value to fix smatch warning
mtd: denali_dt: Use module_platform_driver()
mtd: denali_dt: Fix incorrect error check
mtd: nand: subpage write support for hardware based ECC schemes
mtd: omap2: use msecs_to_jiffies()
mtd: nand_ids: use size macros
mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
mtd: add 4 Toshiba nand chips for the full-id case
mtd: add the support to parse out the full-id nand type
mtd: add new fields to nand_flash_dev{}
mtd: sh_flctl: Use of_match_ptr() macro
mtd: gpio: Use of_match_ptr() macro
mtd: gpio: Use devm_kzalloc()
mtd: davinci_nand: Use of_match_ptr()
mtd: dataflash: Use of_match_ptr() macro
mtd: remove h720x flash support
mtd: onenand: remove OneNAND simulator
...
Linus Torvalds [Thu, 9 May 2013 17:11:48 +0000 (10:11 -0700)]
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewure updates from Stefan Richter:
- fix controller removal when controller is in suspended state
- fix video reception on VIA VT6306 with gstreamer, MythTV, and maybe dv4l
- fix a startup issue with Agere/LSI FW643-e2
- error logging improvements and other small updates
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: dump_stack() for PHY regs read/write failures
firewire: ohci: Improve bus reset error messages
firewire: ohci: Alias dev_* log functions
firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8
firewire: ohci: fix VIA VT6306 video reception
firewire: ohci: Check LPS before register access on pci removal
firewire: ohci: Fix double free_irq()
firewire: remove unnecessary alloc/OOM messages
firewire: sbp2: replace BUG_ON by WARN_ON
firewire: core: remove an always false test
firewire: Remove two unneeded checks for macros
Linus Torvalds [Thu, 9 May 2013 17:11:08 +0000 (10:11 -0700)]
Merge tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull two small EDAC fixes from Borislav Petkov.
* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Don't give write permission to read-only files
EDAC, mc_sysfs.c: Fix string array pointer types
Linus Torvalds [Thu, 9 May 2013 16:59:16 +0000 (09:59 -0700)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
Linus Torvalds [Thu, 9 May 2013 16:46:45 +0000 (09:46 -0700)]
Merge branch 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine updates from Vinod Koul:
"This time we have dmatest improvements from Andy along with dw_dmac
fixes. He has also done support for acpi for dmanegine.
Also we have bunch of fixes going in DT support for dmanegine for
various folks. Then Haswell and other ioat changes from Dave and
SUDMAC support from Shimoda."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
dma: tegra: implement suspend/resume callbacks
dma:of: Use a mutex to protect the of_dma_list
dma: of: Fix of_node reference leak
dmaengine: sirf: move driver init from module_init to subsys_initcall
sudmac: add support for SUDMAC
dma: sh: add Kconfig
at_hdmac: move to generic DMA binding
ioatdma: ioat3_alloc_sed can be static
ioatdma: Adding write back descriptor error status support for ioatdma 3.3
ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
ioatdma: Adding support for 16 src PQ ops and super extended descriptors
ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
dw_dmac: add ACPI support
dmaengine: call acpi_dma_request_slave_channel as well
dma: acpi-dma: introduce ACPI DMA helpers
dma: of: Remove unnecessary list_empty check
DMA: OF: Check properties value before running be32_to_cpup() on it
DMA: of: Constant names
ioatdma: skip silicon bug workaround for pq_align for cb3.3
ioatdma: Removing PQ val disable for cb3.3
...
Linus Torvalds [Thu, 9 May 2013 16:40:49 +0000 (09:40 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
"The most important one is to build thermal core and governor and cpu
cooling code into one module. This fixes a regression that thermal
core does not work if it is built as module, since 3.7. I'll backport
them to stable kernel once those changes are in upstream.
The largest batch is the thermal kernel-doc & coding style
updates/cleanups from Eduardo.
Highlights:
- build all thermal framework code into one module to fix a
regression that thermal does not work if it is built as module.
Jason Cooper [Thu, 9 May 2013 16:06:57 +0000 (09:06 -0700)]
ARM: dts: don't assume boards are using twl4030 for omap3
If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi). Move the phy declaration to the dts
files.
Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered. Ergo, there will always be a valid struct device pointer for
any registered SoC device container. Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.
Simples. The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.
Fix it as noted by Russell.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
EDAC: Don't give write permission to read-only files
I get the following warning on boot:
------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name: -[8737R2A]-
Write permission without 'store'
...
</snip>
Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
batman-adv: reorder clean up routine in order to avoid race conditions
nc_worker accesses the originator table during its periodic
work, but since the originator table is freed before
stopping the worker this leads to a global protection fault.
Fix this by killing the worker (in nc_free) before freeing
the originator table.
Moreover tidy up the entire clean up routine by running all
the subcomponents freeing procedures first and then killing
the TT and the originator tables at the end.
Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batman-adv: make DAT drop ARP requests targeting local clients
In the outgoing ARP request snooping routine in DAT, ARP
Request sent by local clients which are supposed to be
replied by other local clients can be silently dropped.
The destination host will reply by itself through the LAN
and therefore there is no need to involve DAT.
Reported-by: Carlos Quijano <carlos@crqgestion.es> Signed-off-by: Antonio Quartulli <ordex@autistici.org> Tested-by: Carlos Quijano <carlos@crqgestion.es> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Marek Lindner [Tue, 7 May 2013 11:25:02 +0000 (19:25 +0800)]
batman-adv: check return value of pskb_trim_rcsum()
Reported-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Sat, 27 Apr 2013 08:22:28 +0000 (16:22 +0800)]
batman-adv: check proto length before accessing proto string buffer
batadv_param_set_ra() strips the trailing '\n' from the supplied
string buffer without checking the length of the buffer first. This
patches avoids random memory access and associated potential
crashes.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Chris Zankel [Thu, 9 May 2013 05:44:18 +0000 (22:44 -0700)]
xtensa: fix redboot load address
With the patch to support MMUv3, the base address for the loaded
binary image has changed, and a fix was applied to the U-Boot image.
This fixes the RedBoot image.
Max Filippov [Mon, 25 Mar 2013 22:51:43 +0000 (02:51 +0400)]
xtensa: disable IRQs while IRQ handler is running
IRQ handlers are expected to run with IRQs disabled.
See e.g. http://lwn.net/Articles/380931/ for a longer story.
This was overlooked in the commit 2d1c645 xtensa: dispatch medium-priority interrupts
Revert to old behavior and simplify interrupt entry and exit code.
Interrupt handler still honours IRQ priority.
do_notify_resume/schedule must be called with interrupts enabled, enable
interrupts if we return from user exception.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Chris Zankel <chris@zankel.net>
Max Filippov [Sun, 7 Apr 2013 21:29:19 +0000 (01:29 +0400)]
xtensa: provide custom CALLER_ADDR* implementations
Definition of CALLER_ADDR* through __builtin_return_address makes
compiler insert calls to __xtensa_libgcc_window_spill, which in turn
makes fast_syscall_spill_registers syscall that clobbers registers when
called from the kernel mode, leading to invalid opcode exceptions on
return to userspace.
Provide definition for CALLER_ADDR0 as MAKE_PC_FROM_RA(a0, a1) and in
case CONFIG_FRAME_POINTER is enabled extract CALLER_ADDR{1-3} from
stack.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Chris Zankel <chris@zankel.net>
Max Filippov [Mon, 15 Apr 2013 04:39:41 +0000 (08:39 +0400)]
xtensa: don't use a7 in simcalls
To support FRAME_POINTER avoid using a7 in __simc (none of the existing
simcalls needs it). Replace calls to __simc with more specific
simc_read, simc_write and simc_lseek calls.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Chris Zankel <chris@zankel.net>
Max Filippov [Sat, 30 Mar 2013 21:08:22 +0000 (01:08 +0400)]
xtensa: provide default platform_pcibios_init implementation
This fixes the following build error:
arch/xtensa/kernel/built-in.o:(.init.literal+0xe8): undefined reference
to `platform_pcibios_init'
arch/xtensa/kernel/built-in.o: In function `setup_arch':
(.init.text+0x20e): undefined reference to `platform_pcibios_init'
and allows platform to omit definition of platform_pcibios_init if it's
empty.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Chris Zankel <chris@zankel.net>
This patch adds remapping code at the reset vector or at the kernel
_start (depending on CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX) that
reconfigures MMUv3 as MMUv2:
Max Filippov [Sun, 3 Mar 2013 23:40:42 +0000 (03:40 +0400)]
xtensa: fix ibreakenable register update
Only set the register when there is at least one ibreak register,
otherwise the build fails:
arch/xtensa/kernel/head.S:105: Error: invalid register 'ibreakenable'
for 'wsr' instruction
arch/xtensa/platforms/iss/setup.c:67: Error: invalid register
'ibreakenable' for 'wsr' instruction
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Chris Zankel <chris@zankel.net>
A race condition exists when registering the first watchdog device.
Sequence of events:
- watchdog_register_device calls watchdog_dev_register
- watchdog_dev_register creates the watchdog misc device by calling
misc_register.
At that time, the matching character device (/dev/watchdog0) does not yet
exist, and old_wdd is not set either.
- Userspace gets an event and opens /dev/watchdog
- watchdog_open is called and sets wdd = old_wdd, which is still NULL,
and tries to dereference it. This causes the kernel to panic.
Seen with systemd trying to open /dev/watchdog immediately after
it was created.
Tony Lindgren [Wed, 8 May 2013 23:13:14 +0000 (16:13 -0700)]
ARM: dts: Configure and fix the McSPI pins for 4430sdp
The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
commit d16fb25 (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 3027e26 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
projects / mirror_ubuntu-kernels.git / log