Eric Dumazet [Fri, 21 Sep 2018 17:58:07 +0000 (10:58 -0700)]
net/ipv4: avoid compile error in fib_info_nh_uses_dev
net/ipv4/fib_frontend.c: In function 'fib_info_nh_uses_dev':
net/ipv4/fib_frontend.c:322:6: error: unused variable 'ret' [-Werror=unused-variable]
cc1: all warnings being treated as errors
Fixes: 78f2756c5fc0 ("net/ipv4: Move device validation to helper") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Ahern <dsahern@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tcp: switch to Early Departure Time model
In the early days, pacing has been implemented in sch_fq (FQ)
in a generic way :
- SO_MAX_PACING_RATE could be used by any sockets.
- TCP would vary effective pacing rate based on CWND*MSS/SRTT
- FQ would ensure delays between packets based on current
sk->sk_pacing_rate, but with some quantum based artifacts.
(inflating RPC tail latencies)
- BBR then tweaked the pacing rate in its various phases
(PROBE, DRAIN, ...)
This worked reasonably well, but had the side effect that TCP RTT
samples would be inflated by the sojourn time of the packets in FQ.
Also note that when FQ is not used and TCP wants pacing, the
internal pacing fallback has very different behavior, since TCP
emits packets at the time they should be sent (with unreasonable
assumptions about scheduling costs)
Van Jacobson gave a talk at Netdev 0x12 in Montreal, about letting
TCP (or applications for UDP messages) decide of the Earliest
Departure Time, instead of letting packet schedulers derive it
from pacing rate.
Recent additions in linux provided SO_TXTIME and a new ETF qdisc
supporting the new skb->tstamp role
This patch series converts TCP and FQ to the same model.
This might in the future allow us to relax tight TSQ limits
(if FQ is present in the output path), and thus lower
number of callbacks to tcp_write_xmit(), thanks to batching.
This will be followed by FQ change allowing SO_TXTIME support
so that QUIC servers can let the pacing being done in FQ (or
offloaded if network device permits)
For example, a TCP flow rated at 24Mbps now shows a more meaningful RTT
A nice side effect of this patch series is a reduction of max/p99
latencies of RPC workloads, since the FQ quantum no longer adds
artifact.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:54 +0000 (08:51 -0700)]
net_sched: sch_fq: remove dead code dealing with retransmits
With the earliest departure time model, we no longer plan
special casing TCP retransmits. We therefore remove dead
code (since most compilers understood skb_is_retransmit()
was false)
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:52 +0000 (08:51 -0700)]
tcp: switch tcp and sch_fq to new earliest departure time model
TCP keeps track of tcp_wstamp_ns by itself, meaning sch_fq
no longer has to do it.
Thanks to this model, TCP can get more accurate RTT samples,
since pacing no longer inflates them.
This has the nice effect of removing some delays caused by FQ
quantum mechanism, causing inflated max/P99 latencies.
Also we might relax TCP Small Queue tight limits in the future,
since this new model allow TCP to build bigger batches, since
sch_fq (or a device with earliest departure time offload) ensure
these packets will be delivered on time.
Note that other protocols are not converted (they will probably
never be) so sch_fq has still support for SO_MAX_PACING_RATE
Tested:
Test showing FQ pacing quantum artifact for low-rate flows,
adding unexpected throttles for RPC flows, inflating max and P99 latencies.
The parameters chosen here are to show what happens typically when
a TCP flow has a reduced pacing rate (this can be caused by a reduced
cwin after few losses, or/and rtt above few ms)
MIBS="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
Before :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
19,82.78,5279,3825,482.02
After :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
20,49.94,128,63,3.18
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:50 +0000 (08:51 -0700)]
tcp: provide earliest departure time in skb->tstamp
Switch internal TCP skb->skb_mstamp to skb->skb_mstamp_ns,
from usec units to nsec units.
Do not clear skb->tstamp before entering IP stacks in TX,
so that qdisc or devices can implement pacing based on the
earliest departure time instead of socket sk->sk_pacing_rate
Packets are fed with tcp_wstamp_ns, and following patch
will update tcp_wstamp_ns when both TCP and sch_fq switch to
the earliest departure time mechanism.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:48 +0000 (08:51 -0700)]
net_sched: sch_fq: switch to CLOCK_TAI
TCP will soon provide per skb->tstamp with earliest departure time,
so that sch_fq does not have to determine departure time by looking
at socket sk_pacing_rate.
We chose in linux-4.19 CLOCK_TAI as the clock base for transports,
qdiscs, and NIC offloads.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 15:51:46 +0000 (08:51 -0700)]
tcp: switch tcp_clock_ns() to CLOCK_TAI base
TCP pacing is either implemented in sch_fq or internally.
We have the goal of being able to offload pacing on the NICS.
TCP will soon provide per skb skb->tstamp as early departure time.
Like ETF in commit 25db26a91364 ("net/sched: Introduce the ETF Qdisc")
we chose CLOCK_T as the clock base, so that TCP and pacers can share
a common clock, to get better RTT samples (without pacing artificially
inflating these samples).
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Fri, 21 Sep 2018 15:41:48 +0000 (16:41 +0100)]
net: hns3: Remove redundant hclge_get_port_type()
This patch removes hclge_get_port_type which is redundant.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix speed/duplex information loss problem when executing ethtool ethx cmd of VF
Our VF has not implemented the ops for get_port_type. So when we executing
ethtool ethx cmd of VF, hns3_get_link_ksettings will return directly. And
we can not query anything.
To support get_link_ksettings for VF, this patch replaces get_port_type
with get_media_type. If the media type is HNAE3_MEDIA_TYPE_NONE,
hns3_get_link_ksettings will return link information of VF.
Fixes: 12f46bc1d447 ("net: hns3: Refine hns3_get_link_ksettings()") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Fri, 21 Sep 2018 15:41:46 +0000 (16:41 +0100)]
net: hns3: Add get_media_type ops support for VF
This patch adds the ops of get_media_type support for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are already multiple types packets statistics for error packets,
it's unnecessary to print them, which may affect the rx performance if
print too many.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Add unlikely for dma_mapping_error check
For dma_mapping_error is unlikely happened, this patch adds unlikely for
dma_mapping_error check.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Add nic state check before calling netif_tx_wake_queue
When nic down, it firstly calls netif_tx_stop_all_queues(), then calls
napi_disable(). But napi_disable() will wait current napi_poll finish,
it may call netif_tx_wake_queue(). This patch fixes it by add nic state
checking.
Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few "switch-case" codes missed handle for default case. For
some abnormal case, it should return error code instead of return 0.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix of most functions for vf are hclgevf. This patch renames the
function with inconsistent prefix.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix tqp array traversal condition for vf
There are two tqp_num variables "hdev->tqp_num" and "kinfo->tqp_num"
used in VF. "hdev->tqp_num" is the total tqp number allocated to the
VF, and "kinfo->tqp_num" indicates the tqp number being used by the
VF. Usually the two variables are equal. But for the case hdev->tqp_num
larger than rss_size_max, and num_tc is 1, "kinfo->tqp_num" will be
less than "hdev->tqp_num".
In original codes, "hdev->tqp_num" is always used to traverse the
tqp array of kinfo. It may cause null pointer error when "hdev->tqp_num"
is larger than "kinfo->tqp_num"
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some prefix of tx/rx statistic names are redundant, this patch modifies
these names.
The new prefix looks like below:
rxq#1_ -> rxq1_
txq#1_ -> txq1_
tx_dropped -> dropped
tx_wake -> wake
tx_busy -> busy
rx_dropped -> dropped
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For desc.data is already point to the address of struct member "data[6]",
it's unnecessary to use '&' to get its address. This patch unifies all
the type convert for dest.data, using "req = (struct name *)dest.data".
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a defect in hclge_ets_validate(). If each member of tc_tsa is
not IEEE_8021QAZ_TSA_ETS, the variable total_ets_bw won't be updated.
In this case, the check for value of total_ets_bw will fail. This patch
fixes it by checking total_ets_bw only after it has been updated.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Biju Das [Fri, 21 Sep 2018 14:25:43 +0000 (15:25 +0100)]
dt-bindings: net: ravb: Add support for r8a7744 SoC
Document RZ/G1N (R8A7744) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Fri, 21 Sep 2018 13:52:26 +0000 (15:52 +0200)]
ravb: Disable Pause Advertisement
The previous commit to ravb had the side effect of making the PHY
advertise Pause and Asym Pause, which previously did not happen. By
default, phydev->supported has both forms of pause enabled, but
phydev->advertising does not. The new phy_remove_link_mode() copies
phydev->supported to phydev->advertising after removing the requested
link mode. These Pause configuration bits appears it stops the PHY
from completing Auto-Neg and the link remains down. Be explicit and
remove the Pause and Asym Pause modes, so restoring the old behavior.
Fixes: 41124fa64d4b ("net: ethernet: Add helper to remove a supported link mode") Reported-by: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: if_arp: use define instead of hard-coded value
Struct arpreq contains the name of the device. All other places in the
kernel, the define IFNAMSIZ is used to designate its size. But in
if_arp.h, a literal constant is used.
As it could be good reasons to use constants instead of the defines in
include files under uapi, it seems to be OK to use the define here,
without opening a can of worms in user-land.
This because if_arp.h includes netdevice.h, which also uses
IFNAMSIZ. For the distros I have checked, this also holds true for the
use-land side.
The series also fixes some incorrect indents.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/tls: Add support for async encryption of records for performance
In current implementation, tls records are encrypted & transmitted
serially. Till the time the previously submitted user data is encrypted,
the implementation waits and on finish starts transmitting the record.
This approach of encrypt-one record at a time is inefficient when
asynchronous crypto accelerators are used. For each record, there are
overheads of interrupts, driver softIRQ scheduling etc. Also the crypto
accelerator sits idle most of time while an encrypted record's pages are
handed over to tcp stack for transmission.
This patch enables encryption of multiple records in parallel when an
async capable crypto accelerator is present in system. This is achieved
by allowing the user space application to send more data using sendmsg()
even while previously issued data is being processed by crypto
accelerator. This requires returning the control back to user space
application after submitting encryption request to accelerator. This
also means that zero-copy mode of encryption cannot be used with async
accelerator as we must be done with user space application buffer before
returning from sendmsg().
There can be multiple records in flight to/from the accelerator. Each of
the record is represented by 'struct tls_rec'. This is used to store the
memory pages for the record.
After the records are encrypted, they are added in a linked list called
tx_ready_list which contains encrypted tls records sorted as per tls
sequence number. The records from tx_ready_list are transmitted using a
newly introduced function called tls_tx_records(). The tx_ready_list is
polled for any record ready to be transmitted in sendmsg(), sendpage()
after initiating encryption of new tls records. This achieves parallel
encryption and transmission of records when async accelerator is
present.
There could be situation when crypto accelerator completes encryption
later than polling of tx_ready_list by sendmsg()/sendpage(). Therefore
we need a deferred work context to be able to transmit records from
tx_ready_list. The deferred work context gets scheduled if applications
are not sending much data through the socket. If the applications issue
sendmsg()/sendpage() in quick succession, then the scheduling of
tx_work_handler gets cancelled as the tx_ready_list would be polled from
application's context itself. This saves scheduling overhead of deferred
work.
The patch also brings some side benefit. We are able to get rid of the
concept of CLOSED record. This is because the records once closed are
either encrypted and then placed into tx_ready_list or if encryption
fails, the socket error is set. This simplifies the kernel tls
sendpath. However since tls_device.c is still using macros, accessory
functions for CLOSED records have been retained.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: freescale: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: micrel: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Clang warns when a variable is assigned to itself.
drivers/net/fddi/skfp/pcmplc.c:1257:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
phy = phy ; on_off = on_off ;
~~~ ^ ~~~
drivers/net/fddi/skfp/pcmplc.c:1257:21: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
phy = phy ; on_off = on_off ;
~~~~~~ ^ ~~~~~~
2 warnings generated.
Turns out this entire function doesn't actually do anything since
SK_UNUSED is just casting the pointer to void. Remove it to silence
this Clang warning.
Clang warns when a variable is assigned to itself.
drivers/net/ethernet/brocade/bna/bna_enet.c:1800:9: warning: explicitly
assigning value of variable of type 'int' to itself [-Wself-assign]
for (i = i; i < (bna->ioceth.attr.num_ucmac * 2); i++)
~ ^ ~
drivers/net/ethernet/brocade/bna/bna_enet.c:1835:9: warning: explicitly
assigning value of variable of type 'int' to itself [-Wself-assign]
for (i = i; i < (bna->ioceth.attr.num_mcmac * 2); i++)
~ ^ ~
2 warnings generated.
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: warning:
equality comparison with extraneous parentheses [-Wparentheses-equality]
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: note: remove
extraneous parentheses around the comparison to silence this warning
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
~ ^ ~
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: note: use '='
to turn this equality comparison into an assignment
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
^~
=
1 warning generated.
David S. Miller [Fri, 21 Sep 2018 16:14:21 +0000 (09:14 -0700)]
Merge branch 'bnx2x-enhancements'
Shahed Shaikh says:
====================
bnx2x: enhancements
This series adds below changes -
- support for VF spoof-check configuration through .ndo_set_vf_spoofchk.
- workaround for MFW bug regarding unexpected bandwidth notifcation
in single function mode.
- supply VF link status as part of get VF config handling.
====================
bnx2x: Provide VF link status in ndo_get_vf_config
Provide current link status of VF in ndo_get_vf_config
handler.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Ignore bandwidth attention in single function mode
This is a workaround for FW bug -
MFW generates bandwidth attention in single function mode, which
is only expected to be generated in multi function mode.
This undesired attention in SF mode results in incorrect HW
configuration and resulting into Tx timeout.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for `ndo_set_vf_spoofchk' to allow PF control over
its VF spoof-checking configuration.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 20 Sep 2018 10:01:59 +0000 (13:01 +0300)]
vhost_net: add a missing error return
We accidentally left out this error return so it leads to some use after
free bugs later on.
Fixes: 0a0be13b8fe2 ("vhost_net: batch submitting XDP buffers to underlayer sockets") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net_sched: change tcf_del_walker() to take idrinfo->lock
Action API was changed to work with actions and action_idr in concurrency
safe manner, however tcf_del_walker() still uses actions without taking a
reference or idrinfo->lock first, and deletes them directly, disregarding
possible concurrent delete.
Change tcf_del_walker() to take idrinfo->lock while iterating over actions
and use new tcf_idr_release_unsafe() to release them while holding the
lock.
And the blocking function fl_hw_destroy_tmplt() could be called when we
put a filter chain, so defer it to a work queue.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
[xiyou.wangcong@gmail.com: heavily modify the code and changelog] Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 21 Sep 2018 03:01:53 +0000 (20:01 -0700)]
Merge branch 'net-wean-netfilter-from-fib_nh'
David Ahern says:
====================
net: wean netfilter from fib_nh
Two netfilter modules reference fib_nh. In both cases the code is
only checking if a nexthop in a fib_info uses a specific device.
Both instances essentially duplicate code from __fib_validate_source,
so move that code into a helper and flip the netfilter modules to
use it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 20 Sep 2018 20:50:47 +0000 (13:50 -0700)]
net/ipv4: Move device validation to helper
Move the device matching check in __fib_validate_source to a helper and
export it for use by netfilter modules. Code move only; no functional
change intended.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: Further MC-awareness configuration
Petr says:
Due to an issue in Spectrum chips, when unicast traffic shares the same
queue as BUM traffic, and there is congestion, the BUM traffic is
admitted to the queue anyway, thus pushing out all UC traffic. In order
to give unicast traffic precedence over BUM traffic, multicast-aware
mode is now configured on all ports. Under MC-aware mode, egress TCs
8..15 are used for BUM traffic, which has its own dedicated pool.
This patch set improves the way that the MC pool and the higher-order
TCs are integrated into the system.
In patch #1, shaper at the higher TCs is configured to the same value
that it has by default. It's better to have the corresponding artifact
in the code explicitly.
The 8 following patches gradually extend the devlink handling in mlxsw
to support the extra TCs and the new MC pool.
Patch #2 changes the way that pools are indexed in mlxsw. Instead of
using (FW index, direction) tuple to identify the pool and the
associated cache, mlxsw now uses devlink index. This change is necessary
because the new pool 15 is not contiguously adjacent to the
currently-used pools 0..3, and because it's only relevant on egress.
Using devlink index relaxes the requirement for symmetry and adjacency
imposed by using FW indexing.
In patch #3, the assumption that number of ingress TCs matches that of
egress TCs is relaxed to allow exposition of egress TCs 8..15.
In patches #4, #5 and #6, support for infinite quotas is introduced.
Infinite quotas are reported as taking all the memory in the system, but
actually use a mechanism where the infinity is configured explicitly.
In patches #7 and #8, support for configuring static pool sizes in
introduced. Statically-sized pools have been supported for a while now,
but during initialization, all pools have dynamic size. The patches
allow there to be a mix of by-default static and dynamic pools.
In patches #9 and #10, pool 15 resp. per-priority MC quotas are
explicitly configured to be in sync with the current recommendation for
handling BUM traffic in Spectrum chips.
In the following 3 patches, an mlxsw-specific selftest is added to test
the MC-awareness configuration.
First in patches #11 and #12, lib.sh is extended with functions to
collect ethtool stats, and to manage port MTU.
Then in patch #13 the selftest itself is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:36 +0000 (09:21 +0300)]
selftests: mlxsw: Add a test for UC behavior under MC flood
A so-called "MC-aware" mode has recently been enabled in mlxsw. In
MC-aware mode, BUM traffic is handled in a special way so that when a
switch is flooded with BUM, UC performance isn't unduly impacted.
Without enablement of this mode, a stream of BUM traffic can cause
sustained UC throughput drop in excess of 99 %.
Add a test for this behavior. Compare how much UC throughput degrades as
a stream of broadcast frames floods the switch. A minimal degradation is
tolerated to cover for glitches in traffic injection performance.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some selftests need to tweak MTU of an interface, and naturally should
at teardown restore the MTU back to the original value. Add two
functions to facilitate this MTU handling: mtu_set() to change MTU
value, and mtu_reset() to change it back to what it was before.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new service function to obtain ethtool counters.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:33 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Tweak SBMM configuration
The SBMM register configures shared buffer allocation and settings for
MC packets according to switch priority. The recommended values are no
reserved buffer and alpha of 1/4, which corresponds to buf_max of 6.
Update mlxsw_sp_sb_mms accordingly.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:32 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Configure MC pool
Pool 15 (indexed as 8) is dedicated to MC traffic. Its configuration has
been kept at default, because the table-based configuration wasn't
expressive enough to allow the explicit configuration.
Now that the configuration of pool 15 can be described, do so. The MC
pool should have infinite size, infinite per-TC quota, and per-port
limit of 90K.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:31 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Allow configuration of static pools
Some pools configured through the sb_pm entries may have by default
static size. The MC pool is now not explicitly configured, however it
gets configured as static implicitly by 0-initializing sb->prs, and a
follow-up patch adds an explicit configuration to the same effect.
To support this, pass max_buff taken from sb_pm and sb_cm entries
through cell conversion before handing it to mlxsw_sp_sb_pm_write(), if
the pool that the sb_pm entry configures is statically-sized.
To keep current behavior, update mlxsw_sp_sb_cms_egress[] to denote
buffer sizes in bytes (assuming Spectrum 1 cell sizes, which the
original code assumed as well) instead of cells. Note that a follow-up
patch changes this to infinite size.
Also tweak a comment at SBMM configuration to remain true now that
statically-sized pools exist.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:30 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Pass SBPM min_size in cells
The SBPM register configures the shared buffer allocation and
configuration per port and pool. The min_buff value is the buffer size
dedicated to this single function, and is configured in cells.
Currently, all sb_pm entries have 0 for min_buff, and therefore the
actual unit is immaterial. However, in a follow-up patch we want to add
entries with non-zero minimum.
Therefore pass the min_buff from the sb_pm table through the cell
conversion before handing it over to mlxsw_sp_sb_pm_write().
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:29 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Allow an infinite maximum for per-TC pool limit
The SBCM register configures the shared buffer configuration according
to port and TC. So far all pools have had a dynamic size, where the
infinite size is easy to express by using max_buff of 0xff. However the
MC pool should be configured with static size, and the infinite size
thus needs to be set using the field SBCM.infi_max.
Therefore add the field infi_max to the SBCM register and to
mlxsw_reg_sbcm_pack(). Extend mlxsw_sp_sb_cm_write() to handle infinite
sizes as well. Report infinite pool limits as if the limit actually were
the total shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:28 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Allow pools of infinite size
The MC pool should have an infinite size (i.e. no quota).
To that end, add infi_size to the SBPR register and extend
mlxsw_reg_sbpr_pack(). Also add MLXSW_SP_SB_INFI to denote
buffers that should have an infinite size.
Change mlxsw_sp_sb_pr_write() to take as parameter byte size,
instead of cell size, and add the special handling of infinite
buffers. Report pools with infinite size as if they actually
take the full shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:27 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Keep shared buffer size in mlxsw_sp_sb
Entities of infinite size will be reported as if they had the maximum
size allowed by the chip. To that end, keep track of maximum shared
buffer size in mlxsw_sp->sb.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:26 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Split TC_COUNT into ingress and egress
Current code assumes that ingress and egress has the same number of
traffic classes. Since the introduction of MC-aware mode that assumption
hasn't held anymore, and there have been 16 TCs on the egress as opposed
to 8 on ingress.
Break the assumption of symmetry by splitting the artifacts related to
shared-buffer TC counting to ingress and egress parts.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:25 +0000 (09:21 +0300)]
mlxsw: spectrum_buffers: Use devlink pool indices throughout
Currently, mlxsw assumes that each ingress pool has its egress
counterpart, and that pool index for purposes of caching matches the
index with which the hardware should be configured. As we want to expose
the MC pool, both of these assumptions break.
Instead, maintain the pool index as long as possible. Unify ingress and
egress caches and use the pool index as cache index as well. Only
translate to FW pool numbering when actually packing the registers. This
simplifies things considerably, as the pool index is the only quantity
necessary to uniquely identify a pool, and the pool/direction split is
not necessary until firmware is talked to.
To support the mapping between pool indices and pool numbers and
directions, which is not neatly mathematical anymore, introduce a pool
descriptor table, indexed by pool index, to facilitate the translation.
Include the MC pool in the descriptor table as well, so that it can be
referenced from mlxsw_sp_sb_cms_egress.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 20 Sep 2018 06:21:24 +0000 (09:21 +0300)]
mlxsw: spectrum: Init shaper for TCs 8..15
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when more than one set of parentheses are used for single
conditional statements:
drivers/isdn/hisax/w6692.c:627:30: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/isdn/hisax/w6692.c:627:30: note: remove extraneous parentheses
around the comparison to silence this warning
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
~ ^ ~
drivers/isdn/hisax/w6692.c:627:30: note: use '=' to turn this equality
comparison into an assignment
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
^~
=
1 warning generated.
Remove the parentheses to silence this warning.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atl1: remove set but not used variable 'advertising'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_set_link_ksettings':
drivers/net/ethernet/atheros/atlx/atl1.c:3280:6: warning:
variable 'advertising' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/intel/e1000/e1000_main.c: In function 'e1000_watchdog':
drivers/net/ethernet/intel/e1000/e1000_main.c:2436:9: warning:
variable 'txb2b' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 19 Sep 2018 21:42:50 +0000 (14:42 -0700)]
nfp: provide a better warning when ring allocation fails
NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 466271703867 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit. Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors. In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Shearman [Wed, 19 Sep 2018 12:56:53 +0000 (13:56 +0100)]
ipv6: Allow the l3mdev to be a loopback
There is no way currently for an IPv6 client connect using a loopback
address in a VRF, whereas for IPv4 the loopback address can be added:
$ sudo ip addr add dev vrfred 127.0.0.1/8
$ sudo ip -6 addr add ::1/128 dev vrfred
RTNETLINK answers: Cannot assign requested address
So allow ::1 to be configured on an L3 master device. In order for
this to be usable ip_route_output_flags needs to not consider ::1 to
be a link scope address (since oif == l3mdev and so it would be
dropped), and ipv6_rcv needs to consider the l3mdev to be a loopback
device so that it doesn't drop the packets.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com> Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix parameter type for q_id in hclge_tm_q_to_qs_map_cfg()
So far all the places calling hclge_tm_q_to_qs_map_cfg() are assigning
an u16 type value to "q_id", and in the processing of
hclge_tm_q_to_qs_map_cfg(), it also converts the "q_id" to le16.
The max tqp number for pf can be more than 256, we should use "u16" to
store the queue id, instead of "u8", which may cause data lost.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix client initialize state issue when roce client initialize failed
When roce is loaded before nic, the roce client will not be initialized
until nic client is initialized, but roce init flag is set before it.
Furthermore, in this case of nic initialized success and roce failed,
the nic init flag is not set, and roce init flag is not cleared.
This patch fixes it by set init flag only after the client is initialized
successfully.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Clear client pointer when initialize client failed or unintialize finished
If initialize client failed or finish uninitializing client, we should
clear the client pointer. It may cause unexpected result when use
uninitialized client. Meanwhile, we also should check whether client
exist when uninitialize it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix cmdq registers initialization issue for vf
According to hardware's description, the head pointer register should
be written before the tail pointer register while initializing the vf
command queue. Otherwise, it may trigger an interrupt even though there
is no command received.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Fix for setting speed for phy failed problem
The function of genphy_read_status is that reading phy information
from HW and using these information to update SW variable. If user
is using ethtool to setting the speed of phy and service task is calling
by hclge_get_mac_phy_link, the result of speed setting is uncertain.
Because ethtool cmd will modified phydev and hclge_get_mac_phy_link also
will modified phydev.
Because phy state machine will update phy link periodically, we can
just use phydev->link to check the link status. This patch removes
function call of genphy_read_status. To ensure accuracy, this patch
adds a phy state check. If phy state is not PHY_RUNNING, we consider
link is down. Because in some scenarios, phydev->link may be link up,
but phy state is not PHY_RUNNING. This is just an intermediate state.
In fact, the link is not ready yet.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:53 +0000 (18:29 +0100)]
net: hns3: Check hdev state when getting link status
By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: Set STATE_DOWN bit of hdev state when stopping net
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xi Wang [Wed, 19 Sep 2018 17:29:51 +0000 (18:29 +0100)]
net: hns3: Add support for hns3_nic_netdev_ops.ndo_do_ioctl
This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:50 +0000 (18:29 +0100)]
net: hns3: Remove packet statistics of public
All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.
This patch removes all packet statistics of public.
Signed-off-by: Junxin Chen <chenjunxin1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Wed, 19 Sep 2018 17:29:47 +0000 (18:29 +0100)]
net: hns3: Add default irq affinity
All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sun: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: amd: fix return type of ndo_start_xmit function
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / mirror_ubuntu-eoan-kernel.git / log