The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.
This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.
It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)
Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e58901 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We tried to revert commit d9c52fd17cb4 ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8bc ("ath9k: add back support for using active monitor interfaces for tx99") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
lpss_iosf_enter_d3_state() checks if all hw-blocks using the DMA
controllers are in d3 before powering down the DMA controllers.
But on devices, where the I2C bus connected to the PMIC is shared by
the PUNIT, the controller for that bus will never reach d3 since it has
an effectively empty _PS3 method. Instead it appears to automatically
power-down during S0i3 and we never see it as being in d3.
This causes the DMA controllers to never be powered-down on these devices,
causing them to never reach S0i3. This commit uses the ACPI _SEM method
to detect if an I2C bus is shared with the PUNIT and if it is, it removes
it from the mask of devices which lpss_iosf_enter_d3_state() checks for.
This fixes these devices never reaching any S0ix states.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c379d ("gre: Remove support for sharing GRE protocol hook.") Reported-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The terminating NUL byte is only there because the buffer is
allocated with kzalloc(PAGE_SIZE, GFP_KERNEL), but since the
range-check is off-by-one, and PAGE_SIZE==PATH_MAX, the
returned string may not be zero-terminated if it is exactly
PATH_MAX characters long. Furthermore also the initial loop
may theoretically exceed PATH_MAX and cause a fault.
During component_bind_all(), if bind() fails for any
particular component associated with a master, unbind()
should be called for all previous components in that
master's match array, whose bind() might have completed
successfully. As per the current logic, if bind() fails
for the component at position 'n' in the master's match
array, it would start calling unbind() from component in
'n'th position itself and work backwards, and will always
skip calling unbind() for component in 0th position in the
master's match array.
Fix this by updating the loop condition, and the logic to
refer to the components in master's match array, so that
unbind() is called for all components starting from 'n-1'st
position in the array, until (and including) component in
0th position.
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f17f ("mfd: max8998: Add support for Device Tree") Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
dtc has new checks for SPI buses. The meson dts files have a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dtb: Warning (spi_bus_bridge): /soc/periphs@c8834000/pinctrl@4b0/spi: incorrect #address-cells for SPI bus
Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: linux-amlogic@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To reduce latency for interactive and soft real-time applications, bfq
privileges the bfq_queues containing the I/O of these
applications. These privileged queues, referred-to as weight-raised
queues, get a much higher share of the device throughput
w.r.t. non-privileged queues. To preserve this higher share, the I/O
of any non-weight-raised queue must be plugged whenever a sync
weight-raised queue, while being served, remains temporarily empty. To
attain this goal, bfq simply plugs any I/O (from any queue), if a sync
weight-raised queue remains empty while in service.
Unfortunately, this plugging typically lowers throughput with random
I/O, on devices with internal queueing (because it reduces the filling
level of the internal queues of the device).
This commit addresses this issue by restricting the cases where
plugging is performed: if a sync weight-raised queue remains empty
while in service, then I/O plugging is performed only if some of the
active bfq_queues are *not* weight-raised (which is actually the only
circumstance where plugging is needed to preserve the higher share of
the throughput of weight-raised queues). This restriction proved able
to boost throughput in really many use cases needing only maximum
throughput.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sharing the same irqchip with multiple gpiochips is not a good
practice. For instance, when installing hooks, we change the state
of the irqchip. The initial state of the irqchip for the second
gpiochip to register is then disrupted.
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm/boot/dts/socfpga_cyclone5_de0_sockit.dtb: Warning (i2c_bus_reg): /soc/i2c@ffc04000/adxl345@0: I2C bus unit address format error, expected "53"
Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
while compiling an ipq4019 target, dtc will complain:
regulator@b089000 unit address format error, expected "2089000"
The saw0 regulator reg value seems to be
copied and pasted from qcom-ipq8064.dtsi.
This patch fixes the reg value to match that of the
unit address which in turn silences the warning.
(There is no driver for qcom,saw2 right now.
So this went unnoticed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.
There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "has_config" variable is either uninitialized or true. The
"num_pins" variable is unsigned and we verified that it is non-zero on
the lines before so we know "num_pines >= 1" is true. Really, we could
just check "num_configs" directly and remove the "has_config" variable.
The interrupt handler has to be acquired after the other resource
initialization when allocated with IRQF_SHARED. Otherwise it's
triggered before the resource gets ready, and may lead to unpleasant
behavior.
The VIDEO_GET_EVENT and VIDEO_STILLPICTURE was added back in 2005 but
it never worked because the command number is wrong.
Using the right command number means we have a better chance of them
actually doing the right thing, though clearly nobody has ever tried
it successfully.
I noticed these while auditing the remaining users of compat_time_t
for y2038 bugs. This one is fine in that regard, it just never did
anything.
Motion eye video4linux driver for Sony Vaio PictureBook desn't validate user-controlled parameter
'vma->vm_pgoff', a malicious process might access all of kernel memory from user space by trying
pass different arbitrary address.
Discussion: http://www.openwall.com/lists/oss-security/2018/07/06/1
If hv_synic_alloc() errors out, the state of the per-cpu context
for some CPUs is unknown since the zero'ing is done as each
CPU is iterated over. In such case, hv_synic_cleanup() may try to
free memory based on uninitialized values. Fix this by zero'ing
the per-cpu context for all CPUs before doing any memory
allocations that might fail.
Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Instead of calling BUG_ON(), if we find a kprobe in use on free kprobe
list, just remove it from the list and keep it on kprobe hash list
as same as other in-use kprobes.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: David S . Miller <davem@davemloft.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/153666126882.21306.10738207224288507996.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com> Signed-off-by: Viswas G <Viswas.G@microchip.com> Acked-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One of the Freescale recommended sequences for power off with external
PMIC is the following:
...
3. SoC is programming PMIC for power off when standby is asserted.
4. In CCM STOP mode, Standby is asserted, PMIC gates SoC supplies.
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com> Signed-off-by: George Kennedy <george.kennedy@oracle.com> Reviewed-by: Mark Kanda <mark.kanda@oracle.com> Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For userspace to tell the difference between an random signal
and an exception, the exception must include siginfo information.
Using SEND_SIG_FORCED for SIGSEGV is thus wrong, and it will result in
userspace seeing si_code == SI_USER (like a random signal) instead of
si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.
Therefore replace force_sig_info(SIGSEGV, SEND_SIG_FORCE, current)
with force_sig(SIG_SEGV, current) which gets this right and is shorter
and easier to type.
Fixes: 791eca10107f ("uretprobes/x86: Hijack return address") Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For userspace to tell the difference between a random signal and an
exception, the exception must include siginfo information.
Using SEND_SIG_FORCED for SIGILL is thus wrong, and it will result
in userspace seeing si_code == SI_USER (like a random signal) instead
of si_code == SI_KERNEL or a more specific si_code as all exceptions
deliver.
Therefore replace force_sig_info(SIGILL, SEND_SIG_FORCE, current)
with force_sig(SIG_ILL, current) which gets this right and is
shorter and easier to type.
Fixes: 014940bad8e4 ("uprobes/x86: Send SIGILL if arch_uprobe_post_xol() fails") Fixes: 0b5256c7f173 ("uprobes: Send SIGILL if handle_trampoline() fails") Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the first process started (aka /sbin/init) receives a SIGKILL it
will panic the system if it is delivered. Making the system unusable
and undebugable. It isn't much better if the first process started
receives SIGSTOP.
So always ignore SIGSTOP and SIGKILL sent to init.
This is done in a separate clause in sig_task_ignored as force_sig_info
can clear SIG_UNKILLABLE and this protection should work even then.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the set_txreq_header_agh() function returns an error, the exit path
is chosen.
In this path, the code fails to set the return value. This will cause
the caller to not realize an error has occurred.
Set the return value correctly in the error path.
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes: d9c52fd17cb48 ("ath9k: fix tx99 with monitor mode interface") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Acked-by: Eddie Huang <eddie.huang@mediatek.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Users of the mce_register_decode_chain() are called for every logged
error. EDAC drivers should check:
1) Is this a memory error? [bit 7 in status register]
2) Is there a valid address? [bit 58 in status register]
3) Is the address a system address? [bitfield 8:6 in misc register]
The sb_edac driver performed test "1" twice. Waited far too long to
perform check "2". Didn't do check "3" at all.
Fix it by moving the test for valid address from
sbridge_mce_output_error() into sbridge_mce_check_error() and add a test
for the type immediately after. Delete the redundant check for the type
of the error from sbridge_mce_output_error().
Func jz4780_dma_desc_residue() expects the index to the next hw
descriptor as its last parameter. Caller func jz4780_dma_tx_status(),
however, applied modulus before passing it. When the current hw
descriptor was last in the list, the index passed became zero.
The resulting excess of reported residue especially caused problems
with cyclic DMA transfer clients, i.e. ALSA AIC audio output, which
rely on this for determining current DMA location within buffer.
Combined with the recent and related residue-reporting fixes, spurious
ALSA audio underruns on jz4770 hardware are now fixed.
Signed-off-by: Daniel Silsby <dansilsby@gmail.com> Signed-off-by: Paul Cercueil <paul@crapouillou.net> Tested-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we make this driver depend on MACH_JZ4780, that means it can be
enabled only if we're building a kernel specially crafted for a
JZ4780-based board, while most GNU/Linux distributions will want one
generic MIPS kernel that works on multiple boards.
Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
include/trace/events/sched.h includes <linux/sched.h> (via
<linux/sched/numa_balancing.h>) and so knows about the TASK_* constants
used to interpret .prev_state. So instead of duplicating the magic
numbers make use of the defined macros to ease understanding the
mapping from state bits to letters which isn't completely intuitive for
an outsider.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kernel@pengutronix.de Link: http://lkml.kernel.org/r/20180905093636.24068-1-u.kleine-koenig@pengutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Vendor defined U-Boot has changed the partition scheme a while ago:
* kernel partition 6MB
* file system partition uses the remainder up to end of the NAND
* increased size of the environment partition (to get an OneNAND compatible base address)
* shrink the U-Boot partition
Let's be compatible (e.g. Debian kernel built from upstream).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is illegal to change MTU to a value lower than the minimum MTU
stated in ethernet spec. In addition to that we need to add 4 bytes
for encapsulation header (IPOIB_ENCAP_LEN).
Before "ifconfig ib0 mtu 0" command, succeeds while it obviously shouldn't.
Signed-off-by: Muhammad Sammar <muhammads@mellanox.com> Reviewed-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is done in order not to trig the below warning in
ieee80211_rx_napi:
WARN_ON_ONCE(softirq_count() == 0);
ieee80211_rx_napi requires that softirq's are disabled during
execution.
The High latency bus drivers (SDIO and USB) sometimes call the wmi
ep_rx_complete callback from non softirq context, resulting in a trigger
of the above warning.
Calling ieee80211_rx_ni with softirq's already disabled (e.g., from
softirq context) should be safe as the local_bh_disable and
local_bh_enable functions (called from ieee80211_rx_ni) are fully
reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
S5M8767 PMIC interrupt line on Exynos5250-based Arndale board has
external pull-up resistors, so disable any pull control for it in
in controller node. This fixes support for S5M8767 interrupts and
enables operation of wakeup from S5M8767 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We need to bail out if lan78xx_get_endpoints() fails, otherwise the
result is overwritten.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 4a69fcd3a10803 ("ARM: meson: Add DTS for Odroid-C1 and Tronfy MXQ boards") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The clock controller registers are not 0x460 wide because the reset
controller starts at CBUS 0x4404. This currently overlaps with the
clock controller (which is at CBUS 0x4000).
There is no public documentation available on the actual size of the
clock controller's register area (also called "HHI"). However, in
Amlogic's GPL kernel sources the last "HHI" register is
HHI_HDMI_PHY_CNTL2 at CBUS + 0x43a8. 0x400 was chosen because that size
doesn't seem unlikely.
Fixes: 2c323c43a3d619 ("ARM: dts: meson8: add and use the real clock controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Same SSI device may be used in different dai links,
by only having one dma struct in rsnd_ssi, after the first
instance's dma config be initilized, the following instances
can no longer configure dma, this causes issue, when their
dma data address are different from the first instance.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream] Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
imx6_pm_domain_power_off() reads iso and iso2sw from GPC_PGC_PUPSCR_OFFS
which stores the power up delays.
So use GPC_PGC_PDNSCR_OFFS for the correct delays.
Signed-off-by: Sven Schmitt <sven.schmitt@mixed-mode.de> Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In gcc8, when the 3rd argument (size) of a call to strncpy() matches the
length of the first argument, the compiler warns of the possibility of an
unterminated string. Using strlcpy() forces a null at the end.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The RTC controller is fed by an external fixed 32kHz clock. Yet the
driver wants to acquire this clock, even though it doesn't make any use
of it, ie. doesn't get the rate to make calculation.
Therefore, use the exported 32.768kHz clock in the PXA clock tree to
make the driver happy and working.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's no point in warning here, the user will just get an
error back to the debugfs file write, and warning just makes
it seem like there's an internal consistency problem when in
reality the user just happened to hit this at a bad time.
Remove the warning.
Fixes: f45f979dc208 ("iwlwifi: mvm: disable dbg data collect when fw isn't alive") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a read request is retried for the remaining partial
data, the response may restart from read response first
or read response only. So support those cases.
Do not advance the comp psn beyond the current wqe's last_psn
as that could skip over an entire read wqe and will cause the
req_retry() logic to set an incorrect req psn.
An example sequence is as follows:
Write PSN 40 -- this is the current WQE.
Read request PSN 41
Write PSN 42
Receive ACK PSN 42 -- this will complete the current WQE
for PSN 40, and set the comp psn to 42 which is a problem
because the read request at PSN 41 has been skipped over.
So when req_retry() tries to retransmit the read request,
it sets the req psn to 42 which is incorrect.
When retrying a read request, calculate the number of psns
completed based on the dma resid instead of the wqe first_psn.
The wqe first_psn could have moved if the read request was
retried multiple times.
Set the reth length to the dma resid to handle read retries for
the remaining partial data.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Caught by GCC 8. When we provide a length for strncpy, we should not
include the terminating null. So we must tell it one less than the size
of the destination buffer.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Regulators, which are marked as 'on-in-suspend' seems to be critical for
board operation, thus they must not be disabled anytime. This can be
only assured by marking them as 'always-on', because otherwise some
actions of their clients might result in turning them off. This patch
restores suspend/resume operation on Peach-Pit Chromebook board. It
partially reverts 'always-on' property removal done by the commit
mentioned in the Fixes tag.
Fixes: 665c441eea3d ("ARM: dts: exynos: Remove unneded always-on for regulators on Peach boards") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Tomasz Figa <tfiga@chromium.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In lio_enable_irq, the pkt_in_done count register was being cleared to
zero. However, there could be some completed instructions which were not
yet processed due to budget and limit constraints.
So, only write this register with the number of actual completions
that were processed.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch adds missing properties to the CODEC and sound nodes, so the
audio will work also on Snow rev5 Chromebook. This patch is an extension
to the commit e9eefc3f8ce0 ("ARM: dts: exynos: Add missing clock and
DAI properties to the max98095 node in Snow Chromebook")
and commit 6ab569936d60 ("ARM: dts: exynos: Enable HDMI audio on Snow
Chromebook"). It has been reported that such changes work fine on the
rev5 board too.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Fixed typo in phandle to &max98090] Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Setting GPIO 21 high seems to be required to enable power to USB ports
on the WNDR3400v3. As there is already similar code for WNR3500L,
make the existing USB power GPIO code generic and use that.
If the CPU DAI does not initialise rate_max, say if using
using KNOT or CONTINUOUS, then the rate_max field will be
initialised to 0. A value of zero in the rate_max field of
the hardware runtime will cause the sound card to support no
sample rates at all. Obviously this is not desired, just a
different mechanism is being used to apply the constraints. As
such update the setting of rate_max in dpcm_init_runtime_hw
to be consistent with the non-DPCM cases and set rate_max to
UINT_MAX if nothing is defined on the CPU DAI.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The GFS2_RDF_UPTODATE flag in the rgrp is used to determine when
a rgrp buffer is valid. It's cleared when the glock is invalidated,
signifying that the buffer data is now invalid. But before this
patch, function update_rgrp_lvb was setting the flag when it
determined it had a valid lvb. But that's an invalid assumption:
just because you have a valid lvb doesn't mean you have valid
buffers. After all, another node may have made the lvb valid,
and this node just fetched it from the glock via dlm.
Consider this scenario:
1. The file system is mounted with RGRPLVB option.
2. In gfs2_inplace_reserve it locks the rgrp glock EX, but thanks
to GL_SKIP, it skips the gfs2_rgrp_bh_get.
3. Since loops == 0 and the allocation target (ap->target) is
bigger than the largest known chunk of blocks in the rgrp
(rs->rs_rbm.rgd->rd_extfail_pt) it skips that rgrp and bypasses
the call to gfs2_rgrp_bh_get there as well.
4. update_rgrp_lvb sees the lvb MAGIC number is valid, so bypasses
gfs2_rgrp_bh_get, but it still sets sets GFS2_RDF_UPTODATE due
to this invalid assumption.
5. The next time update_rgrp_lvb is called, it sees the bit is set
and just returns 0, assuming both the lvb and rgrp are both
uptodate. But since this is a smaller allocation, or space has
been freed by another node, thus adjusting the lvb values,
it decides to use the rgrp for allocations, with invalid rd_free
due to the fact it was never updated.
This patch changes update_rgrp_lvb so it doesn't set the UPTODATE
flag anymore. That way, it has no choice but to fetch the latest
values.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.
This to avoid following warnings:
drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
dev_warn(ext->dev,
^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
case CHT_WC_USBSRC_TYPE_SDP:
^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Martin Lucina <martin@lucina.net> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>