powerpc/powernv: Rename machine_check_pSeries_early() to powernv
The routine machine_check_pSeries_early() is only used on powernv, not
pseries. Hence rename machine_check_pSeries_early() to
machine_check_powernv_early().
Reported-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl: Check periodically the coherent platform function's state
In the PowerVM environment, the PHYP CoherentAccel component manages
the state of the Coherent Accelerator Processor Interface adapter and
virtualizes CAPI resources, handles CAPP, PSL, PSL Slice errors - and
interrupts - and provides a new set of hcalls for the OS APIs to utilize
Accelerator Function Unit (AFU).
During the course of operation, a coherent platform function can
encounter errors. Some possible reason for errors are:
• Hardware recoverable and unrecoverable errors
• Transient and over-threshold correctable errors
PHYP implements its own state model for the coherent platform function.
The state of the AFU is available through a hcall.
The current implementation of the cxl driver, for the PowerVM
environment, checks this state of the AFU only when an action is
requested - open a device, ioctl command, memory map, attach/detach a
process - from an external driver - cxlflash, libcxl. If an error is
detected the cxl driver handles the error according the content of the
Power Architecture Platform Requirements document.
But in case of low-level troubles (or error injection), the PHYP
component may reset the card and change the AFU state. The PHYP
interface doesn't provide any way to be notified when that happens thus
implies that the cxl driver:
• cannot handle immediatly the state change of the AFU.
• cannot notify other drivers (cxlflash, ...)
The purpose of this patch is to wake up the cpu periodically to check
the current state of each AFU and to see if we need to enter an error
recovery path.
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Fri, 6 May 2016 07:46:36 +0000 (17:46 +1000)]
cxl: Add kernel API to allow a context to operate with relocate disabled
cxl devices typically access memory using an MMU in much the same way as
the CPU, and each context includes a state register much like the MSR in
the CPU. Like the CPU, the state register includes a bit to enable
relocation, which we currently always enable.
In some cases, it may be desirable to allow a device to access memory
using real addresses instead of effective addresses, so this adds a new
API, cxl_set_translation_mode, that can be used to disable relocation
on a given kernel context. This can allow for the creation of a special
privileged context that the device can use if it needs relocation
disabled, and can use regular contexts at times when it needs relocation
enabled.
This interface is only available to users of the kernel API for obvious
reasons, and will never be supported in a virtualised environment.
This will be used by the upcoming cxl support in the mlx5 driver.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Wed, 4 May 2016 04:52:58 +0000 (14:52 +1000)]
cxl: Ensure PSL interrupt is configured for contexts with no AFU IRQs
In the cxl kernel API, it is possible to create a context and start it
without allocating any interrupts. Since we assign or allocate the PSL
interrupt when allocating AFU interrupts this will lead to a situation
where we start the context with no means to take any faults.
The user API is not affected as it always goes through the cxl interrupt
allocation code paths and will have the PSL interrupt allocated or
assigned, even if no AFU interrupts were requested.
This checks that at least one interrupt is configured at the time of
attach, and if not it will assign the multiplexed PSL interrupt for
powernv, or allocate a single interrupt for PowerVM.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Wed, 4 May 2016 04:48:32 +0000 (14:48 +1000)]
cxl: Remove duplicate #defines
These defines are not used, but other equivalent definitions
(CXL_SPA_SW_CMD_*) are used. Remove the unused defines.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Wed, 4 May 2016 04:46:30 +0000 (14:46 +1000)]
cxl: Handle num_of_processes larger than can fit in the SPA
num_of_process is a 16 bit field, theoretically allowing an AFU to
support 16K processes, however the scheduled process area currently has
a maximum size of 1MB, which limits the maximum number of processes to
7704.
Some AFUs may not necessarily care what the limit is and just want to be
able to use the maximum by setting the field to 16K. To allow these to
work, detect this situation and use the maximum size for the SPA.
Downgrade the WARN_ON to a dev_warn.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 26 Feb 2016 00:26:26 +0000 (11:26 +1100)]
powerpc/mm: Improve readability of update_mmu_cache()
The function is used to update the MMU with software PTE. It can
be called by data access exception handler (0x300) or instruction
access exception handler (0x400). If the function is called by
0x400 handler, the local variable @access is set to _PAGE_EXEC
to indicate the software PTE should have that flag set. When the
function is called by 0x300 handler, @access is set to zero.
This improves the readability of the function by replacing if
statements with switch. No logical changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The zone that contains the top of memory will be either ZONE_NORMAL
or ZONE_HIGHMEM depending on the kernel config. There are two functions
that require this information and both of them use an #ifdef to set
a local variable (top_zone). This is a little silly so lets just make it
a constant.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Cc: linux-mm@kvack.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a switch fallthough in instr_analyze() which can cause an
invalid instruction to be emulated as a different, valid, instruction.
The rld* (opcode 30) case extracts a sub-opcode from bits 3:1 of the
instruction word. However, the only valid values of this field are 001
and 000. These cases are correctly handled, but the others are not which
causes execution to fall through into case 31.
Breaking out of the switch causes the instruction to be marked as
unknown and allows the caller to deal with the invalid instruction in a
manner consistent with other invalid instructions.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit be96f63375a1 ("powerpc: Split out instruction analysis part of
emulate_step()") introduced ldarx and stdcx into the instructions in
sstep.c, which are not accepted by the assembler on powerpcspe, but does
seem to be accepted by the normal powerpc assembler even in 32 bit mode.
Wrap these two instructions in a __powerpc64__ check like it is
everywhere else in the file.
Fixes: be96f63375a1 ("powerpc: Split out instruction analysis part of emulate_step()") Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Mackerras [Wed, 13 Apr 2016 11:31:24 +0000 (21:31 +1000)]
powerpc/xmon: Fix SPR read/write commands and add command to dump SPRs
xmon has commands for reading and writing SPRs, but they don't work
currently for several reasons. They attempt to synthesize a small
function containing an mfspr or mtspr instruction and call it. However,
the instructions are on the stack, which is usually not executable.
Also, for 64-bit we set up a procedure descriptor, which is fine for the
big-endian ABIv1, but not correct for ABIv2. Finally, the code uses the
infrastructure for catching memory errors, but that only catches data
storage interrupts and machine check interrupts, but a failed
mfspr/mtspr can generate a program interrupt or a hypervisor emulation
assist interrupt, or be a no-op.
Instead of trying to synthesize a function on the fly, this adds two new
functions, xmon_mfspr() and xmon_mtspr(), which take an SPR number as an
argument and read or write the SPR. Because there is no Power ISA
instruction which takes an SPR number in a register, we have to generate
one of each possible mfspr and mtspr instruction, for all 1024 possible
SPRs. Thus we get just over 8k bytes of code for each of xmon_mfspr()
and xmon_mtspr(). However, this 16kB of code pales in comparison to the
> 130kB of PPC opcode tables used by the xmon disassembler.
To catch interrupts caused by the mfspr/mtspr instructions, we add a new
'catch_spr_faults' flag. If an interrupt occurs while it is set, we come
back into xmon() via program_check_interrupt(), _exception() and die(),
see that catch_spr_faults is set and do a longjmp to bus_error_jmp, back
into read_spr() or write_spr().
This adds a couple of other nice features: first, a "Sa" command that
attempts to read and print out the value of all 1024 SPRs. If any mfspr
instruction acts as a no-op, then the SPR is not implemented and not
printed.
Secondly, the Sr and Sw commands detect when an SPR is not
implemented (i.e. mfspr is a no-op) and print a message to that effect
rather than printing a bogus value.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On some architectures (powerpc in particular), the number of registers
exceeds what can be represented in an integer bitmask. Ensure we
generate the proper bitmask on such platforms.
Fixes: 71ad0f5e4 ("perf tools: Support for DWARF CFI unwinding on post processing") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With perf regs support enabled for powerpc, in commit ed4a4ef85cf5
("powerpc/perf: Add support for sampling interrupt register state"),
the support for obtaining perf user stack dump is already enabled. This
patch declares the support for same and also updates documentation to
mark the support for perf-regs and perf-stackdump.
Signed-off-by: Chandan Kumar <chandan.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/hash64: Fix subpage protection with 4K HPTE config
With Linux page size of 64K and hardware only supporting 4K HPTE, if we
use subpage protection, we always fail for the subpage 0 as shown
below (using the selftest subpage_prot test):
520175565: (4520111850): Failed at 0x3fffad4b0000 (p=13,sp=0,w=0), want=fault, got=pass ! 4520890210: (4520826495): Failed at 0x3fffad5b0000 (p=29,sp=0,w=0), want=fault, got=pass ! 4521574251: (4521510536): Failed at 0x3fffad6b0000 (p=45,sp=0,w=0), want=fault, got=pass ! 4522258324: (4522194609): Failed at 0x3fffad7b0000 (p=61,sp=0,w=0), want=fault, got=pass !
This is because hash preload wrongly inserts the HPTE entry for subpage
0 without looking at the subpage protection information.
Fix it by teaching should_hash_preload() not to preload if we have
subpage protection configured for that range.
It appears this has been broken since it was introduced in 2008.
Fixes: fa28237cfcc5 ("[POWERPC] Provide a way to protect 4k subpages when using 64k pages") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rework into should_hash_preload() to avoid build fails w/SLICES=n] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/hash64: Factor out hash preload psize check
Currently we have a check in hash_preload() against the psize, which is
only included when CONFIG_PPC_MM_SLICES is enabled. We want to expand
this check in a subsequent patch, so factor it out to allow that. As a
bonus it removes the #ifdef in the C code.
Unfortunately we can't put this in the existing CONFIG_PPC_MM_SLICES
block because it would require a forward declaration.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc: Update of_remove_property() call sites to remove null checking
After obtaining a property from of_find_property() and before calling
of_remove_property() most code checks to ensure that the property
returned from of_find_property() is not null. The previous patch moved
this check to the start of the function of_remove_property() in order to
avoid the case where this check isn't done and a null value is passed.
This ensures the check is always conducted before taking locks and
attempting to remove the property. Thus it is no longer necessary to
perform a check for null values before invoking of_remove_property().
Update of_remove_property() call sites in order to remove redundant
checking for null property value as check is now performed within the
of_remove_property function().
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[mpe: Unbreak some lines which are just >80 chars for readability] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
drivers/of: Add check for null property in of_remove_property()
The validity of the property input argument to of_remove_property() is
never checked within the function and thus it is possible to pass a null
value. It happens that this will be picked up in __of_remove_property()
as no matching property of the device node will be found and thus an
error will be returned, however once again there is no explicit check
for a null value. By the time this is detected 2 locks have already been
acquired which is completely unnecessary if the property to remove is
null.
Add an explicit check in the function of_remove_property() for a null
property value and return -ENODEV in this case, this is consistent with
what the previous return value would have been when the null value was
not detected and passed to __of_remove_property().
By moving an explicit check for the property paramenter into the
of_remove_property() function, this will remove the need to perform this
check in calling code before invocation of the of_remove_property()
function.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Add null property check to pseries_discover_pic()
The return value of of_get_property() isn't checked before it is passed
to the strstr() function, if it happens that the return value is null
then this will result in a null pointer being dereferenced.
Add a check to see if the return value of of_get_property() is null and
if it is continue straight on to the next node.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Reviewed-by: Chris Smart <chris@distroguy.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv/pci: Fix cfg_dbg() & replace with pr_devel()
When cfg_dbg() is enabled (i.e. mapped to printk()), gcc produces
errors as the __func__ parameter is missing (pnv_pci_cfg_read() has one);
this adds the missing parameter.
cfg_dbg() is just an inferior version of pr_devel() so use the latter
instead.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Chris Smart [Mon, 2 May 2016 03:51:38 +0000 (13:51 +1000)]
selftests/powerpc: Test cp_abort during context switch
Test that performing a copy paste sequence in userspace on P9 does not
result in a leak of the copy into the paste of another process.
This is based on Anton Blanchard's context_switch benchmarking code. It
sets up two processes tied to the same CPU, one which copies and one
which pastes.
The paste should never succeed and the test fails if it does.
This is a test for commit, "8a64904 powerpc: Add support for userspace
P9 copy paste."
Patch created with much assistance from Michael Neuling
<mikey@neuling.org>
Signed-off-by: Chris Smart <chris@distroguy.com> Reviewed-by: Cyril Bur <cyrilbur@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Chris Smart [Mon, 2 May 2016 06:00:58 +0000 (16:00 +1000)]
powerpc: Remove unnecessary CONFIG_SMP #ifdefs
The code in machine_restart/power_off/halt() includes #ifdefs around
calls to smp_send_stop(), however these are not required as
include/linux/smp.h includes an empty version of this function for
CONFIG_SMP=n builds.
Signed-off-by: Chris Smart <chris@distroguy.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Support for the A2 cpu was removed in commit fb5a515704d7 ("powerpc:
Remove platforms/wsp and associated pieces"), and the externs:
__setup_cpu_a2 and __restore_cpu_a2 are still around and unused, so
remove them.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The usage in mm mmu_context_nohash.c is bogus, because we set the
context.id value to MMU_NO_CONTEXT 4 lines previously in the same
function, meaning slice_mm_new_context() will always be true.
The book3s 64 usage was removed in the previous commit. So remove it as
unused.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/subpage: Initialise user psize correctly
As part of the radix support we switched Book3s64 to use a value of ~0
for MMU_NO_CONTEXT. That is because id 0 is special on radix.
However that broke the logic in init_new_context(). The code there needs
to differentiate between a newly allocated context and one inherited via
fork. Previously it worked because a newly allocated context has an id
of zero (because it was just memset() to zero), which used to match
MMU_NO_CONTEXT, and therefore slice_mm_new_context() did the right
thing.
Instead check against a context.id value of zero instead of using
slice_mm_new_context().
Without this patch we never call slice_set_user_psize(), and end up with
a slice psize value of zero and we always end up using 4K HPTE.
powerpc/mm/radix: Use firmware feature to enable Radix MMU
We use the existing "ibm,pa-features" device-tree property to enable
Radix MMU mode. This means we default to hash mode unless firmware tells
us it's OK to start using Radix mode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Add THP support for 4K linux page size
This adds THP support for 4K Linux page size config with radix. We still
don't do THP with 4K Linux page size and hash page table. Hash page
table needs a 16MB hugepage and we can't do THP with 16MM hugepage and
4K Linux page size.
We add missing functions to 4K hash config to get it to build and
hash__has_transparent_hugepage() makes sure we don't enable THP for 4K
hash config. To catch wrong usage of THP related with 4K config, we add
BUG() in those dummy functions we added to get it compile.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The deposited pgtable_t is a pte fragment hence we cannot use page->lru
for linking then together. We use the first two 64 bits for pte fragment
as list_head type to link all deposited fragments together. On withdraw
we properly zero then out.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In this patch we make the number of pte fragments per level 4 page table
page a variable. Radix level 4 table size is 256 bytes and hence we can
have 256 fragments per level 4 page. We don't update the fragment count
in this patch. We need to do performance measurements to find the right
value for fragment count.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: vmalloc abstraction in preparation for radix
The vmalloc range differs between hash and radix config. Hence make
VMALLOC_START and related constants a variable which will be runtime
initialized depending on whether hash or radix mode is active.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Fix missing init of ioremap_bot in pgtable_64.c for ppc64e] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Make 4K and 64K use pte_t for pgtable_t
This patch switches 4K Linux page size config to use pte_t * type
instead of struct page * for pgtable_t. This simplifies the code a lot
and helps in consolidating both 64K and 4K page allocator routines. The
changes should not have any impact, because we already store physical
address in the upper level page table tree and that implies we already
do struct page * to physical address conversion.
One change to note here is we move the pgtable_page_dtor() call for
nohash to pte_fragment_free_mm(). The nohash related change is due to
the related changes in pgtable_64.c.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Revert changes made to nohash pgalloc-64.h
This reverts pgalloc related changes WRT implementing 4-level page
table for 64K Linux page size and storing of physical address in higher
level page tables since they are only applicable to book3s64 variant
and we now have a separate copy for book3s64. This helps to keep these
headers simpler.
Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Make a copy of pgalloc.h for 32 and 64 book3s
This patch start to make a book3s variant for pgalloc headers. We have
multiple book3s specific changes such as:
* 4 level page table
* store physical address in higher level table
* use pte_t * for pgtable_t
Having a book3s64 specific variant helps to keep code simpler and remove
lots of #ifdef around code.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Pick the address layout for radix config
Hash needs special get_unmapped_area() handling because of limitations
around base page size, so we have to set HAVE_ARCH_UNMAPPED_AREA.
With radix we don't have such restrictions, so we could use the generic
code. But because we've set HAVE_ARCH_UNMAPPED_AREA (for hash), we have
to re-implement the same logic as the generic code.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to add asm changes in the follow up patches. Add the
feature bit now so that we can get it all build.
mpe: When CONFIG_PPC_RADIX_MMU=n we omit MMU_FTR_RADIX from the
MMU_FTRS_POSSIBLE mask. This allows the compiler to work out that those
checks will always be false and so the code can be elided completely.
Note we do *not* define MMU_FTR_RADIX to 0 in the RADIX_MMU=n case,
because that doesn't work with the ASM_FTR patching. In particular an
IF_SET section will result in a mask and value of zero, which is always
true, meaning the section *won't* be patched, which is the opposite of
what we want.
Michael Ellerman [Wed, 11 May 2016 05:30:47 +0000 (15:30 +1000)]
powerpc/mm: Add mask of possible MMU features
Follow the example of the cpu feature code, and add a mask of possible
MMU features, MMU_FTRS_POSSIBLE.
This is used in mmu_has_feature(), which allows the possible mask to act
as a shortcut for any features that are not possible, but still allows
the feature bit itself to be defined.
We will use this in the next commit to allow MMU_FTR_RADIX checks to be
elided when MMU_FTR_RADIX is not possible.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Core kernel doesn't track the page size of the VA range that we are
invalidating. Hence we end up flushing TLB for the entire mm here. Later
patches will improve this.
We also don't flush page walk cache separetly instead use RIC=2 when
flushing TLB, because we do a MMU gather flush after freeing page table.
MMU_NO_CONTEXT is updated for hash.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Abstraction for vmemmap and map_kernel_page()
For hash we create vmemmap mapping using bolted hash page table entries.
For radix we fill the radix page table. The next patch will add the
radix details for creating vmemmap mappings.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Add radix callbacks for early init routines
This adds routines for early setup for radix. We use device tree
property "ibm,processor-radix-AP-encodings" to find supported page
sizes. If we don't find the above we consider 64K and 4K as supported
page sizes.
We do map vmemap using 2M page size if we can. The linear mapping is
done such that we use required page size for that range. For example
memory of 3.5G is mapped such that we use 1G mapping till 3G range and
use 2M mapping for the rest.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Add radix callback for pmd accessors
This only does 64K Linux page support for now. 64K hash Linux config
THP needs to differentiate it from hugetlb huge page because with THP we
need to track hash pte slot information with respect to each subpage.
This is not needed with hugetlb hugepage, because we don't do MPSS with
hugetlb.
Radix doesn't have any such restrictions.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Move hugetlb and THP related pmd accessors to pgtable.h
Here we create pgtable-64/4k.h and move pmd accessors that are common
between hash and radix there. We can't do much sharing with 4K Linux
page size because 4K Linux page size with hash config doesn't support
THP. So for now it is empty. In later patches we will add functions that
does conditional hash/radix accessors there.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For those pte accessors, that operate on a different set of pte bits
between hash/radix, we add a generic variant that does a conditional
to hash linux or radix variant.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In this patch we add the radix Kconfig and conditional check.
radix_enabled() is written to always return 0 here. Once we have all
needed radix changes added, we will update this to an mmu_feature check.
We need to add this early so that we can get it all build in the early
stage.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds Power ISA 3.0 specific pte defines. We share most of the
details with hash Linux page table format. This patch indicates only
things where we differ.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix and hash MMU models support different page table sizes. Make
the #defines a variable so that existing code can work with variable
sizes.
Slice related code is only used by hash, so use hash constants there. We
will replicate some of the boundary conditions with resepct to TASK_SIZE
using radix values too. Right now we do boundary condition check using
hash constants.
Swapper pgdir size is initialized in asm code. We select the max pgd
size to keep it simple. For now we select hash pgdir. When adding radix
we will switch that to radix pgdir which is 64K.
BUILD_BUG_ON check which is removed is already done in hugepage_init()
using MAYBE_BUILD_BUG_ON().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/book3s: Rename hash specific PTE bits to carry H_ prefix
This helps to make following hash only pte bits easier.
We have kept _PAGE_CHG_MASK, _HPAGE_CHG_MASK and _PAGE_PROT_BITS as it
is in this patch eventhough they use hash specific bits. Using them in
radix as it is should be ok, because with radix we expect those bit
positions to be zero.
Only renames in this patch, no change in functionality.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerISA 3.0 adds a parition table indexed by LPID. Parition table
allows us to specify the MMU model that will be used for guest and host
translation.
This patch adds support with SLB based hash model (UPRT = 0). What is
required with this model is to support the new hash page table entry
format and also setup partition table such that we use hash table for
address translation.
We don't have segment table support yet.
In order to make sure we don't load KVM module on Power9 (since we don't
have kvm support yet) this patch also disables KVM on Power9.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Use generic version of ptep_clear_flush_young()
The radix variant is going to require a flush_tlb_range(). With
flush_tlb_range() added, ptep_clear_flush_young() is the same as the
generic version. So drop the powerpc specific variant.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Use generic version of pmdp_clear_flush_young()
The radix variant is going to require a flush_pmd_tlb_range(). With
flush_pmd_tlb_range() added, pmdp_clear_flush_young() is the same as the
generic version. So drop the powerpc specific variant.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PowerISA 3.0 introduces two pte bits with the below meaning for radix:
00 -> Normal Memory
01 -> Strong Access Order (SAO)
10 -> Non idempotent I/O (Cache inhibited and guarded)
11 -> Tolerant I/O (Cache inhibited)
We drop the existing WIMG bits in the Linux page table in favour of the
above constants. We loose _PAGE_WRITETHRU with this conversion. We only
use writethru via pgprot_cached_wthru() which is used by
fbdev/controlfb.c which is Apple control display and also PPC32.
With respect to _PAGE_COHERENCE, we have been marking hpte always
coherent for some time now. htab_convert_pte_flags() always added
HPTE_R_M.
NOTE: KVM changes need closer review.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PS3 had used a PPP bit hack to implement a read only mapping in the
kernel area. Since we are bolting the ioremap area, it used the pte
flags _PAGE_PRESENT | _PAGE_USER to get a PPP value of 0x3 there by
resulting in a read only mapping. This means the area can be accessed by
user space, but kernel will never return such an address to user space.
But we can do better by implementing a read only kernel mapping using
PPP bits 0b110.
This also allows us to do read only kernel mapping for radix in later
patches.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PTE_RPN_SHIFT is actually page size dependent. Even though PowerISA 3.0
expects only the lower 12 bits to be zero, we will always find the pages
to be PAGE_SHIFT aligned. In case of hash config, this also allows us to
use the additional 3 bits to track pte specific information. We need
to make sure we use these bits only for hash specific pte flags.
For both 4K and 64K config, pte now can hold 57 bits address.
Inorder to keep things simpler, drop PTE_RPN_SHIFT and PTE_RPN_SIZE and
specify the 57 bit detail explicitly.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Replace _PAGE_USER with _PAGE_PRIVILEGED
_PAGE_PRIVILEGED means the page can be accessed only by the kernel. This
is done to keep pte bits similar to PowerISA 3.0 Radix PTE format. User
pages are now marked by clearing _PAGE_PRIVILEGED bit.
Previously we allowed the kernel to have a privileged page in the lower
address range (USER_REGION). With this patch such access is denied.
We also prevent a kernel access to a non-privileged page in higher
address range (ie, REGION_ID != 0).
Both the above access scenarios should never happen.
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a common declaration in pte-common.h Add a book3s specific one
and switch to pte_user() in callchain.c. In a subsequent patch we will
switch _PAGE_USER to _PAGE_PRIVILEGED in the book3s version only.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Apr 2016 13:25:32 +0000 (23:25 +1000)]
powerpc/mm: Convert pte_user() to static inline
In a subsequent patch we want to add a second definition of pte_user().
Before we do that, make the signature clear, ie. it takes a pte_t and
returns bool.
We move it up inside the existing #ifndef __ASSEMBLY__ block, but
otherwise it's a straight conversion.
Convert the call in settlbcam(), which passes an unsigned long, to pass
a pte_t.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/subpage: Clear RWX bit to indicate no access
Subpage protection used to depend on the _PAGE_USER bit to implement no
access mode. This patch switches that to use _PAGE_RWX. We clear Read,
Write and Execute access from the pte instead of clearing _PAGE_USER
now. This was done so that we can switch to _PAGE_PRIVILEGED in a later
patch.
subpage_protection() returns pte bits that need to be cleared. Instead
of updating the interface to handle no-access in a separate way, it
appears simpler to clear RWX acecss to indicate no access.
We still don't insert hash ptes for no access implied by !_PAGE_RWX.
Hence we should not get PROT_FAULT with change.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Use _PAGE_READ to indicate Read access
This splits the _PAGE_RW bit into _PAGE_READ and _PAGE_WRITE. It also
removes the dependency on _PAGE_USER for implying read only. Few things
to note here is that, we have read implied with write and execute
permission. Hence we should always find _PAGE_READ set on hash pte
fault.
We still can't switch PROT_NONE to !(_PAGE_RWX). Auto numa depends on
marking a prot none pte _PAGE_WRITE. (For more details look at b191f9b106ea "mm: numa: preserve PTE write permissions across a NUMA
hinting fault")
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Acked-by: Ian Munsie <imunsie@au1.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Apr 2016 13:25:29 +0000 (23:25 +1000)]
powerpc/mm: Use pte_raw() in pte_same()/pmd_same()
We can avoid doing endian conversions by using pte_raw() in pxx_same().
The swap of the constant (_PAGE_HPTEFLAGS) should be done at compile
time by the compiler.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Use big endian Linux page tables for book3s 64
Traditionally Power server machines have used the Hashed Page Table MMU
mode. In this mode Linux manages its own tree of nested page tables,
aka. "the Linux page tables", which are not used by the hardware
directly, and software loads translations into the hash page table for
use by the hardware.
Power ISA 3.0 defines a new MMU mode, known as Radix Tree Translation,
where the hardware can directly operate on the Linux page tables.
However the hardware requires that the page tables be in big endian
format.
To accommodate this, switch the pgtable types to __be64 and add
appropriate endian conversions.
Because we will be supporting a single kernel binary that boots using
either radix or hash mode, we always store the Linux page tables big
endian, even in hash mode where they are not actually used by the
hardware.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Fix sparse errors, flesh out change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Apr 2016 13:25:27 +0000 (23:25 +1000)]
powerpc/mm: Add pte_xchg() helper
We have five locations in 64-bit hash MMU code that do a cmpxchg() of a
PTE. Currently doing it inline OK, but in a future patch we will be
converting the PTEs to __be64 in some configs. In that case we will need
casts at every cmpxchg() site in order to keep sparse happy.
So move the logic into a helper, this is a reasonably nice cleanup on
its own.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Apr 2016 13:25:25 +0000 (23:25 +1000)]
powerpc/mm: Always use STRICT_MM_TYPECHECKS
Testing done by Paul Mackerras has shown that with a modern compiler
there is no negative effect on code generation from enabling
STRICT_MM_TYPECHECKS.
So remove the option, and always use the strict type definitions.
Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IB/qib: Use cache inhibitted and guarded mapping on powerpc
The driver was requesting for a writethrough mapping. But with those
flags we will end up with an SAO mapping because we now have memory
conherence always enabled. ie, the existing mapping will end up with a
WIMG value 0b1110 which is Strong Access Order.
Update this to use cache inhibitted guarded mapping.
Cc: Doug Ledford <dledford@redhat.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: linux-rdma@vger.kernel.org Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ftrace: Match dot symbols when searching functions on ppc64
In the ppc64 big endian ABI, function symbols point to function
descriptors. The symbols which point to the function entry points
have a dot in front of the function name. Consequently, when the
ftrace filter mechanism searches for the symbol corresponding to
an entry point address, it gets the dot symbol.
As a result, ftrace filter users have to be aware of this ABI detail on
ppc64 and prepend a dot to the function name when setting the filter.
The perf probe command insulates the user from this by ignoring the dot
in front of the symbol name when matching function names to symbols,
but the sysfs interface does not. This patch makes the ftrace filter
mechanism do the same when searching symbols.
Fixes the following failure in ftracetest's kprobe_ftrace.tc:
.../kprobe_ftrace.tc: line 9: echo: write error: Invalid argument
That failure is on this line of kprobe_ftrace.tc:
echo _do_fork > set_ftrace_filter
This is because there's no _do_fork entry in the functions list:
projects / mirror_ubuntu-zesty-kernel.git / log