Luciano Coelho [Tue, 28 Feb 2012 17:13:28 +0000 (19:13 +0200)]
wlcore: add a debugfs entry to allow changing the sleep mode by hand
For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want. To allow
this, a debugfs entry is added.
Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.
Arik Nemtsov [Wed, 6 Jun 2012 07:48:56 +0000 (10:48 +0300)]
wlcore: suppress error message on Rx BA session removal
The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.
Eliad Peller [Wed, 13 Jun 2012 17:29:16 +0000 (20:29 +0300)]
wlcore: declare interface combinations
Advertise to the stack that the wlcore driver
supports multiple interfaces for a single device.
This is required in order to be able to run
multirole with mac80211.
Yair Shapira [Wed, 13 Jun 2012 14:14:22 +0000 (17:14 +0300)]
wlcore: add print logs of radio_status in case of BIP calibration
FEM BIP calibration may fail with fw/phy radio status. In order to
recognize these failures a log is added to the calibration answer
(TEST_CMD_P2G_CAL)
Yair Shapira [Wed, 13 Jun 2012 14:14:21 +0000 (17:14 +0300)]
wlcore/wl12xx: add support for HP and SKW FEM radio manufacturers
Add support for HP (High Performance TQS fem type 3) and SKW
(fem type 2). This is done by increasing the number of FEM
manufacturers to 4.
Usually FEM parameters from ini file are read from nvs file and
passed to firmware using TEST_CMD_INI_FILE_RADIO_PARAM. Still,
because the nvs file has only place for 2 FEMs, we need to pass the
new FEM types information in one of the available entries.
This is done by mapping new fem types 2,3 to entry 0. This solution
works for manual FEM selection. AutoDetect-FEM still support only
fem types 0 and 1.
Eliad Peller [Tue, 12 Jun 2012 09:45:27 +0000 (12:45 +0300)]
wlcore: update basic rates on channel switch
On channel switch we have to update the basic rates, in
order to reflect possible band changes (otherwise, we
might start beaconing on 11a with the default rates
of 11g).
Eyal Shapira [Tue, 12 Jun 2012 09:39:55 +0000 (12:39 +0300)]
wlcore: send EAPOLs with basic rate policy
EAPOLs are sent at high rates as they are considered
data packets. Some APs like Motorola Symbol AP7131 and AP650
don't respond well to these rates and don't respond with
EAPOL 3/4 consistently. When sending EAPOL 2/4 at 54Mbps
we've seen approx 30% success rate in getting EAPOL 3/4 response
while using 11Mbps we got 100% success.
To increase the chances of successful 4-Way handshake with
such APs, send EAPOLs with basic rate policy in order to avoid
high rates.
Eyal Shapira [Mon, 11 Jun 2012 14:59:55 +0000 (17:59 +0300)]
wlcore: avoid using NET_IP_ALIGN for RX alignment
NET_IP_ALIGN can be overriden on different architectures
and therefore cannot be used in the RX path to account
for the 2 bytes added for alignment (either by the FW
in the case of 18xx or by the host for 12xx).
Instead use an internal define.
Arik Nemtsov [Tue, 29 May 2012 09:44:12 +0000 (12:44 +0300)]
wl18xx: clean up phy module parameters
Give all wl18xx phy module paramters -1 as a default value, indicating
the paramter was not set. Add previous default values to the default
18xx priv conf structure.
Remove the board_type field from wl18xx priv. The field with the same
name inside the phy conf is good enough for our purposes.
Arik Nemtsov [Tue, 29 May 2012 09:40:50 +0000 (12:40 +0300)]
wl18xx: align wl18xx_conf_phy with FW variant and remove it
wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params
structure. Remove it and replace the phy part of the wl18xx conf with the
FW bound structure. This allows us to set/override all members.
Increment the wlconf version to ensure compatibility with the new
structure
Luciano Coelho [Thu, 7 Jun 2012 20:39:28 +0000 (23:39 +0300)]
wl18xx: read configuration structure from a binary file
Instead of using the hardcoded configuration structure, try to read it
from a "firmware" file called wl18xx-conf.bin. If the file doesn't
exist, fall back to the hardcoded version. If the file exists but is
illegal, bail out.
Luciano Coelho [Thu, 7 Jun 2012 20:39:25 +0000 (23:39 +0300)]
wlcore: use u8 instead of enum for bcn_filt_mode
Since we will export the conf structure as a file, we need to use well
defined types. Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.
Luciano Coelho [Thu, 7 Jun 2012 20:39:24 +0000 (23:39 +0300)]
wlcore/wl18xx/wl12xx: use u8 instead of bool for host_fast_wakeup_support
The conf structure is going to be exported to a file, so we should use
only well defined types. bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Luciano Coelho [Thu, 7 Jun 2012 20:39:22 +0000 (23:39 +0300)]
wl18xx: add support to clear FW statistics
This patch calls ACX_CLEAR_STATISTICS to clear the firmware
statistics. The trigger is a new debugfs file called
clear_fw_statistics in the fw_stats directory.
Eyal Shapira [Thu, 7 Jun 2012 20:39:21 +0000 (23:39 +0300)]
wlcore: add debugfs control over rx interrupt pacing
Add control over several conf fields which combined
control the rx interrupt pacing mechanism, that is avoiding
getting an interrupt following a single frame rx but instead
have the FW trigger the interrupt only after a certain
amount of frames received or a timeout.
Eyal Shapira [Thu, 7 Jun 2012 20:39:20 +0000 (23:39 +0300)]
wlcore: add support macros to easily add conf debugfs entries
The current debugfs code contains too much code duplication
of bolierplate code. Add some macro magic to avoid this and
enable adding new debugfs entries by using just a few lines.
Ido Reis [Sun, 13 May 2012 11:53:40 +0000 (14:53 +0300)]
wl18xx: pad only last frame in aggregration buffer for PG2
In PG2 only the last frame in the aggregate buffer should be
aligned to the sdio block size. This frame's header msb should be
set to 0, while in all the previous frames in the aggregation
buffer, this bit should be set to 1.
[Add a HW op for setting the frame ctrl bit only for 18xx. Other minor
cleanups - Arik]
[Make the pre_pkt_send operation optional -- Luca]
Ido Reis [Mon, 23 Apr 2012 14:35:25 +0000 (17:35 +0300)]
wl18xx: PG2.0 HW Watch dog interrupt support
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and
the SW watchdog is relocated to bit9. We perform the relocation
globally, as there's only one watchdog bit on previous platforms (bit0).
[Only mask in the new bit9 for platforms supporting it. This avoids
spurious events on other platforms - Arik]
wlcore: set channels 12-14 as pactive for sched scan
Introduce “pactive” scan mode – which instructs the fw to
perform a passive scan until an activity/energy is detected
on these channels, once energy detected the channel becomes
active.
Signed-off-by: Victor Goldenshtein <victorg@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Yoni Divinsky [Wed, 16 May 2012 08:34:17 +0000 (11:34 +0300)]
wlcore: add role_id to all the sched_scan commands
Due to a need by the firmware when working in multirole
the role id needs to be added to the structs of the
following commands:
CMD_CONNECTION_SCAN_CFG, CMD_CONNECTION_SCAN_SSID_CFG,
CMD_START_PERIODIC_SCAN, CMD_STOP_PERIODIC_SCAN
Eliad Peller [Tue, 15 May 2012 13:35:20 +0000 (16:35 +0300)]
wl12xx/wl18xx: add erp protection IE to the beacon filter
We have to reconfigure the fw when erp protection should
be enabled/disabled. Pass beacons containing changes
in the ERP protection IE, so we could analyze them.
Yoni Divinsky [Wed, 16 May 2012 08:34:18 +0000 (11:34 +0300)]
wlcore: do not send stop fwlog cmd if fw is hanged
If the driver received a watchdog interrupt then the
assumption is that the fw is hanged. Avoid sending
the stop fwlog command in case of a watchdog recovey
to avoid waiting for the 2 seconds timeout of the command.
Arik Nemtsov [Fri, 18 May 2012 04:46:40 +0000 (07:46 +0300)]
wlcore/wl12xx/wl18xx: implement op_set_key per HW arch
The 12xx set_key just calls the common wlcore_set_key function, in order
to program the keys into the FW.
The 18xx variant changes the spare block count when a GEM or TKIP
key is set. Also modify the get_spare_blocks HW op for 18xx to return
the correct numbers of spare blocks, according to what is currently
set in FW.
Arik Nemtsov [Fri, 18 May 2012 04:46:38 +0000 (07:46 +0300)]
wlcore: add stop reason bitmap for waking/starting queues
Allow the driver to wake/stop the queues for multiple reasons. A queue
is started when no stop-reasons exist.
Convert all wake/stop queue calls to use the new API.
Before, a stopped queue was almost synonymous a high-watermark on Tx.
Remove a bit of code in wl12xx_tx_reset() that relied on it.
Internal packets arriving from mac80211 are also discarded when a queue
is stopped. A notable exception to this is the watermark reason, which
is a "soft"-stop reason. We allow traffic to gradually come to a halt,
but we don't mind spurious packets here and there. This is merely a flow
regulation mechanism.
Based on a similar patch by Eliad Peller <eliadWizery.com>.
Arik Nemtsov [Fri, 18 May 2012 04:46:37 +0000 (07:46 +0300)]
wlcore/wl12xx/wl18xx: handle spare blocks spacial cases per arch
Add a HW op for getting spare blocks.
12xx cards require 2 spare blocks for GEM encrypted SKBs, regardless
of VIFs or keys programmed into the FW.
18xx cards require 2 spare blocks when there are any connected TKIP or
GEM VIFs. For now always return 2 spare blocks, as this works with all
networks. The special case TKIP/GEM functionality is added at a later
patch.
Arik Nemtsov [Fri, 18 May 2012 04:46:36 +0000 (07:46 +0300)]
wlcore/wl12xx/wl18xx: introduce quirk to remove TKIP header space
18xx chips do not require extra space in the TKIP header. Introduce a
new HW quirk to allow us to make this feature arch-specific. 12xx chip
will now have this quirk.
wlcore: wait for roc complete only for the first roc command
In some multi role scenarios the driver might send multi
roc requests without sending a croc first, the fw queues
those requests and starts service the next roc request as
soon as the driver sends a croc for the previous one. So,
if the fw rocs on channel X and driver asks to roc also
on channel Y, the fw will not start service Y (and will
not send roc complete event for this request) until the
driver releases the fw with croc X.
Signed-off-by: Victor Goldenshtein <victorg@ti.com> Signed-off-by: Igal Chernobelsky <igalc@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Tue, 15 May 2012 13:46:58 +0000 (16:46 +0300)]
wlcore: remove duplicate BUG_ON during recovery
This BUG_ON also ignored the INTENDED_FW_RECOVERY flag. This would
result in a BUG() when using the bug_on_recovery module parameter during
multi-role.
Yoni Divinsky [Tue, 8 May 2012 11:02:12 +0000 (14:02 +0300)]
wl12xx: set the irq polarity before loading the fw
The polarity should be set before the firmware is loaded
since the firmware touches the same register. Access
of the firmware and driver to the same register will
cause a collision since there is no exclusion scheme.
Yoni Divinsky [Tue, 8 May 2012 11:02:11 +0000 (14:02 +0300)]
wlcore: use psd_type indexing according to spec
In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.
In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Eliad Peller [Tue, 15 May 2012 14:08:55 +0000 (17:08 +0300)]
wlcore: use correct link for bcast/multicast frames
Multicast management frames (e.g. global deauth)
should be sent out on the bcast link, rather than
the global, which should be used only for pre-added
stations (e.g. for auth/assoc resp).
Arik Nemtsov [Tue, 15 May 2012 14:08:54 +0000 (17:08 +0300)]
wlcore: fixes for connection_loss_work
We can't use cancel_delayed_work_sync() from functions that take the
wl->mutex, since connection_loss_work also takes the mutex. This might
result in a deadlock. Restructure the code so the work is synchronously
canceled before taking the mutex.
Avoid a bug where we would indefinitely delay the connection loss
indication by re-queuing the connection loss work on consecutive beacon
loss events.
Arik Nemtsov [Tue, 15 May 2012 14:08:53 +0000 (17:08 +0300)]
wlcore: fix dynamic_ps_timeout time regression
In patch d7b63b9fc7ee73e75a4c7fdb899 we have raised the dynamic
PS timeout to 200ms to improve user experience. Re-apply the change,
since it was reverted in the wlcore split.
Luciano Coelho [Mon, 4 Jun 2012 21:02:25 +0000 (00:02 +0300)]
wlcore/wl12xx/wl18xx: don't use TX align quirk for wl127x
Commit 4afc37 (wlcore: reorder identify_chip and get_hw_info) broke
support for wl127x chips.
When we moved the identify_chip operation to an earlier stage (ie. to
the probe function), we broke wl127x support because during HW init we
would set the WLCORE_QUIRK_TX_BLOCKSIZE_ALIGN.
To avoid this, set this quirk in the identify_chip operations and only
force it to be unset if the bus module doesn't support it. We were
doing the opposite and setting the flag if the bus module supports it.
Assaf Azulay [Thu, 10 May 2012 09:14:23 +0000 (12:14 +0300)]
wl18xx: change default tcp_checksum to false
as tcp check sum is going to be removed from firmware, and as
there is a problem with getting dns in security when checksum is
enabled, it was decided to disable it by default.
for none security modes it can be enabled by module paramenter.
Luciano Coelho [Thu, 10 May 2012 09:14:20 +0000 (12:14 +0300)]
wlcore: increase aggregation buffer size by one page
With 4 pages (16Kb), we can't fit 10 frames in the aggregation buffer
during iperf. This is the optimal for the firmware. Thus, increase
the buffer size by one page.
Luciano Coelho [Thu, 10 May 2012 09:14:19 +0000 (12:14 +0300)]
wlcore/wl12xx/wl18xx: move lower driver debugfs to a subdir
Instead of adding more files from the lower drivers into the same
directory in debugfs as wlcore, we now add a subdirectory for the
lower driver. This makes things a bit easier, because we can quickly
see where the debugfs entry is implemented and what is specific to the
lower driver.
Luciano Coelho [Thu, 10 May 2012 09:14:17 +0000 (12:14 +0300)]
wl18xx: export low/high band component values as module params
We use hardcoded values for the different board types. In some cases
we may need to override the defaults, so export the values as module
params. If not defined, the defaults for the specified board type
will be used.
Luciano Coelho [Thu, 10 May 2012 09:14:16 +0000 (12:14 +0300)]
wl18xx: add power limit reference value to mac_and_phy settings
With more recent PHY firmware versions (>8.1.0.0.116), we need to use
the correct value for the pwr_limit_reference_11_abg parameter when
setting the mac_and_phy options.
For now we use a hardcoded 0xc8 as the value. This will be moved to
the configuration binary when it gets implemented.
Luciano Coelho [Thu, 10 May 2012 09:14:15 +0000 (12:14 +0300)]
wl18xx: add module parameter to force SISO 20MHz
In some cases it may be useful to force narrow-band SISO channels.
Add a new value to the ht_mode module parameter to force the device to
operate in SISO 20MHz.
Luciano Coelho [Thu, 10 May 2012 09:14:14 +0000 (12:14 +0300)]
wlcore: use proper values for supported local rates
We were setting all the rates bits when starting the AP role. Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates). This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Luciano Coelho [Thu, 10 May 2012 09:14:13 +0000 (12:14 +0300)]
wl18xx: don't use MIMO when ht_mode is set to wide
If the wl18xx module is loaded with ht_mode=wide (the default), we
shouldn't use MIMO rates when the channel type is not HT40. Fix this
by checking the ht_mode before deciding which rates to used.
Additionally, set the ht_mode parameter explicitly to "wide" as the
default.
Luciano Coelho [Thu, 10 May 2012 09:14:12 +0000 (12:14 +0300)]
wlcore: print the interrupt status when recovery is triggered
In some cases it may be useful for debugging to check what is the
status of the interrupt register when a hardware recovery happens.
Print the contents of REG_INTERRUPT_NO_CLEAR (aka. HINT_STS_RAW) when
recovery starts.
Luciano Coelho [Thu, 10 May 2012 09:14:11 +0000 (12:14 +0300)]
wl18xx: print the PHY firmware version from the private static data
The wl18xx firmware writes the PHY firmware version in the static
data. Add an operation to parse the static data and print the PHY
firmware version when booting.
Luciano Coelho [Thu, 10 May 2012 09:14:10 +0000 (12:14 +0300)]
wlcore: create private static_data area and add operation to parse it
The wl18xx firmware has more information in the static_data than
wl12xx. To be able to parse that in an abstracted way, this patch
adds a priv area to the static data struct and an operation that
allows the lower driver to parse it if necessary.
Luciano Coelho [Thu, 10 May 2012 09:14:07 +0000 (12:14 +0300)]
wlcore: add debugfs macro to help print fw statistics arrays
Add a macro to make it easy to print arrays from the FW statistics
array in debugfs. At the same time, increase the buffer size so
arrays fit more easily.
Luciano Coelho [Thu, 10 May 2012 09:14:05 +0000 (12:14 +0300)]
wlcore: use all AP basic rates as default
Sometimes we get a BSS_CHANGED_BEACON_ENABLED event before the basic
rates have been properly set. To avoid problems with the firmware not
expecting to receive frames at rates that are not set during
CMD_START_ROLE, we now start with all basic rates by default.
Luciano Coelho [Thu, 10 May 2012 09:14:04 +0000 (12:14 +0300)]
wlcore: update beacon and probe_resp templates when rates change
When the data rates change, we get BSS_CHANGED_BASIC_RATES. At this
point, we should update all the templates to match the new rates. We
were changing some of the templates, but the beacon and the probe
response templates were missing.
Luciano Coelho [Thu, 10 May 2012 09:14:02 +0000 (12:14 +0300)]
wlcore: reorder identify_chip and get_hw_info
We can do get the HW information and identify the chip already at
probe time. This makes it easier to mangle with the parameters during
identify chip before registering the hardware with mac80211.
Luciano Coelho [Thu, 10 May 2012 09:14:01 +0000 (12:14 +0300)]
wl18xx: change low_band_component_type value for COM8
Like HDK, COM8 uses 0x06 for the low_band_component_type as well.
Hardcode the value for COM8 until this configuration can be done in
the external configuration binary (to be implemented).
Luciano Coelho [Thu, 10 May 2012 09:14:00 +0000 (12:14 +0300)]
wlcore: add space for private area when allocating fw_status
When allocating the fw_status structure, the space for the
lower-driver private area was missing. This was causing an illegal
write outside the allocated area, which was causing random oopses
around the kernel.
Luciano Coelho [Thu, 10 May 2012 09:13:58 +0000 (12:13 +0300)]
wl18xx: copy the default configuration before checking the board_type
We were changing the low_band_component_type in the private
configuration structure before copying the default values to it, so
the change was overwritten and only took effect after HW recovery.
Luciano Coelho [Thu, 10 May 2012 09:13:56 +0000 (12:13 +0300)]
wl18xx: add a module parameter to control 11a support
In wl18xx we don't have an NVS yet, so we need to control whether 11a
is supported with a module parameter for now. 11a support is enabled
by default and can be changed by setting enable_11a to false when
loading the module.
Arik Nemtsov [Thu, 10 May 2012 09:13:54 +0000 (12:13 +0300)]
wlcore/wl12xx/18xx: split fw_status struct into two
The number of RX packet descriptors may vary from chip to chip and
in different firmware versions. Unfortunately, the array that
contains the actual descriptors is in the middle of the fw_status
structure. To manage this, we split the struct into two so we can
calculate the offset of what comes after the array and access the last
elements more easily.
[Changed the STATUS_LEN macro to be placement agnostic - Arik]
Luciano Coelho [Thu, 10 May 2012 09:13:52 +0000 (12:13 +0300)]
wl18xx: add number of antennas and dc2dc type as module params
We need to specify the number of 2.4GHz and 5GHz antennas and whether
the board has an internal or external DC2DC. Add some module
parameters that allow changing that.
Luciano Coelho [Thu, 10 May 2012 09:13:51 +0000 (12:13 +0300)]
wl18xx: change the low_band_component_type for HDK boards
Currently, all HDK boards use low_band_component_type 0x06. In the
future this may change, but for now, we hardcode this value when the
board_type is set to HDK.
Luciano Coelho [Thu, 10 May 2012 09:13:49 +0000 (12:13 +0300)]
wlcore/wl12xx: add plt_init op and move the code to wl12xx
PLT mode needs to be initialized differently for each chip. This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Arik Nemtsov [Thu, 10 May 2012 09:13:47 +0000 (12:13 +0300)]
wl18xx: don't upload NVS to FW
In this chip family the NVS file should not be uploaded to FW. In fact,
we encounter strange bugs (sdio errors) when trying to upload it with
certain parameters.
Luciano Coelho [Thu, 10 May 2012 09:13:45 +0000 (12:13 +0300)]
wlcore/wl12xx: move rx_mem_pool_addr element to wl12xx
Only wl127x chips use the rx_mem_pool_addr values, which need to be
given to the firmware as part of the RX path. Move this from core to
the wl12xx driver.
projects / mirror_ubuntu-jammy-kernel.git / log