drm/i915: Adjust CDCLK accordingly to our DBuf bw needs
According to BSpec max BW per slice is calculated using formula
Max BW = CDCLK * 64. Currently when calculating min CDCLK we
account only per plane requirements, however in order to avoid
FIFO underruns we need to estimate accumulated BW consumed by
all planes(ddb entries basically) residing on that particular
DBuf slice. This will allow us to put CDCLK lower and save power
when we don't need that much bandwidth or gain additional
performance once plane consumption grows.
v2: - Fix long line warning
- Limited new DBuf bw checks to only gens >= 11
v3: - Lets track used Dbuf bw per slice and per crtc in bw state
(or may be in DBuf state in future), that way we don't need
to have all crtcs in state and those only if we detect if
are actually going to change cdclk, just same way as we
do with other stuff, i.e intel_atomic_serialize_global_state
and co. Just as per Ville's paradigm.
- Made dbuf bw calculation procedure look nicer by introducing
for_each_dbuf_slice_in_mask - we often will now need to iterate
slices using mask.
- According to experimental results CDCLK * 64 accounts for
overall bandwidth across all dbufs, not per dbuf.
v4: - Fixed missing const(Ville)
- Removed spurious whitespaces(Ville)
- Fixed local variable init(reduced scope where not needed)
- Added some comments about data rate for planar formats
- Changed struct intel_crtc_bw to intel_dbuf_bw
- Moved dbuf bw calculation to intel_compute_min_cdclk(Ville)
v5: - Removed unneeded macro
v6: - Prevent too frequent CDCLK switching back and forth:
Always switch to higher CDCLK when needed to prevent bandwidth
issues, however don't switch to lower CDCLK earlier than once
in 30 minutes in order to prevent constant modeset blinking.
We could of course not switch back at all, however this is
bad from power consumption point of view.
v7: - Fixed to track cdclk using bw_state, modeset will be now
triggered only when CDCLK change is really needed.
v8: - Lock global state if bw_state->min_cdclk is changed.
- Try getting bw_state only if there are crtcs in the commit
(need to have read-locked global state)
v9: - Do not do Dbuf bw check for gens < 9 - triggers WARN
as ddb_size is 0.
v10: - Lock global state for older gens as well.
v11: - Define new bw_calc_min_cdclk hook, instead of using
a condition(Manasi Navare)
v12: - Fixed rebase conflict
v13: - Added spaces after declarations to make checkpatch happy.
Checking with hweight8 if plane configuration had
changed seems to be wrong as different plane configs
can result in a same hamming weight.
So lets check the bitmask itself.
v2: Fixed "from" field which got corrupted for some weird reason
drm/i915: Extract cdclk requirements checking to separate function
In Gen11+ whenever we might exceed DBuf bandwidth we might need to
recalculate CDCLK which DBuf bandwidth is scaled with.
Total Dbuf bw used might change based on particular plane needs.
Thus to calculate if cdclk needs to be changed it is not enough
anymore to check plane configuration and plane min cdclk, per DBuf
bw can be calculated only after wm/ddb calculation is done and
all required planes are added into the state. In order to keep
all min_cdclk related checks in one place let's extract it into
separate function, checking and modifying any_ms.
drm/i915: Decouple cdclk calculation from modeset checks
We need to calculate cdclk after watermarks/ddb has been calculated
as with recent hw CDCLK needs to be adjusted accordingly to DBuf
requirements, which is not possible with current code organization.
Setting CDCLK according to DBuf BW requirements and not just rejecting
if it doesn't satisfy BW requirements, will allow us to save power when
it is possible and gain additional bandwidth when it's needed - i.e
boosting both our power management and perfomance capabilities.
This patch is preparation for that, first we now extract modeset
calculation from modeset checks, in order to call it after wm/ddb
has been calculated.
v2: - Extract only intel_modeset_calc_cdclk from intel_modeset_checks
(Ville Syrjälä)
v3: - Clear plls after intel_modeset_calc_cdclk
v4: - Added r-b from previous revision to commit message
Chris Wilson [Thu, 21 May 2020 14:49:49 +0000 (15:49 +0100)]
drm/i915: Remove PIN_UPDATE for i915_vma_pin
As we no longer use PIN_UPDATE (since commit 7d0aa0db4375 ("drm/i915/gem:
Unbind all current vma on changing cache-level")) we can remove
PIN_UPDATE itself. The benefit is just in simplifing the vma bind.
Chris Wilson [Thu, 21 May 2020 14:06:17 +0000 (15:06 +0100)]
drm/i915: Avoid using rq->engine after free during i915_fence_release
In order to be valid to dereference during the i915_fence_release, after
retiring the fence and releasing its refererences, we assume that
rq->engine can only be a real engine (that stay intact until the device
is shutdown after all fences have been flushed). However, due to a quirk
of preempt-to-busy, we may retire a request that still belongs to a
virtual engine and so eventually free it with rq->engine being invalid.
To avoid dereferencing that invalid engine, we look at the
execution_mask which if it indicates it may be executed on more than one
engine, we know it originated on a virtual engine and may still be on
one.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1906 Fixes: 43acd6516ca9 ("drm/i915: Keep a per-engine request pool") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200521140617.30015-2-chris@chris-wilson.co.uk
Chris Wilson [Thu, 21 May 2020 14:06:16 +0000 (15:06 +0100)]
drm/i915: Disable semaphore inter-engine sync without timeslicing
Since the removal of the no-semaphore boosting, we rely on timeslicing to
reorder passed inter-dependency hogs across the engines. However, we
require preemption to support timeslicing into user payloads, and not all
machine support preemption so we do not universally enable timeslicing,
even when it would correctly preempt our own inter-engine semaphores.
Since timeslicing and semaphore priority deboosting is now disabled on
Broadwell/Braswell, we have to follow suite and not use semaphores.
Testcase: igt/gem_exec_schedule/semaphore-codependency # bdw/bsw Fixes: 18e4af04d218 ("drm/i915: Drop no-semaphore boosting") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200521140617.30015-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 21 May 2020 12:43:04 +0000 (13:43 +0100)]
drm/i915/selftests: Flush the submission, not cancel it!
Use intel_engine_flush_submission() when we want to ensure that the
tasklet is run. tasklet_kill(), while it may ensure that an ongoing
tasklet is completed, also prevents the tasklet from running if it's
already scheduled and hasn't yet been run.
Matt Roper [Mon, 4 May 2020 22:52:13 +0000 (15:52 -0700)]
drm/i915/rkl: Add power well support
RKL power wells are similar to TGL power wells, but have some important
differences:
* PG1 now has pipe A's VDSC (rather than sticking it in PG2)
* PG2 no longer exists
* DDI-C (aka TC-1) moves from PG1 -> PG3
* PG5 no longer exists due to the lack of a fourth pipe
Also note that what we refer to as 'DDI-C' and 'DDI-D' need to actually
be programmed as TC-1 and TC-2 even though this platform doesn't have TC
outputs.
Bspec: 49234 Cc: Imre Deak <imre.deak@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200504225227.464666-9-matthew.d.roper@intel.com
Matt Roper [Mon, 4 May 2020 22:52:12 +0000 (15:52 -0700)]
drm/i915/rkl: Limit number of universal planes to 5
RKL only has five universal planes, plus a cursor. Since the
bottom-most universal plane is considered the primary plane, set the
number of sprites available on this platform to 4.
In general, the plane capabilities of the remaining planes stay the same
as TGL. However the NV12 Y-plane support moves down to the new top two
planes and now only the bottom three planes can be used for NV12 UV.
Chris Wilson [Wed, 20 May 2020 07:30:48 +0000 (08:30 +0100)]
drm/i915/gt: Remove errant assertion in __intel_context_do_pin
This assertion was removed in commit b412c63f1cba ("drm/i915/gt: Report
context-is-closed prior to pinning"), but accidentally restored by a
cherry-pick into drm-next and now has percolated back to
drm-intel-next-queued.
Fixes: 2e46a2a0b014 ("drm/i915: Use explicit flag to mark unreachable intel_context") Fixes: 2b703bbda271 ("Merge drm/drm-next into drm-intel-next-queued")
References: b412c63f1cba ("drm/i915/gt: Report context-is-closed prior to pinning") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200520073048.2394034-1-chris@chris-wilson.co.uk
Chris Wilson [Tue, 19 May 2020 13:20:46 +0000 (14:20 +0100)]
drm/i915/gt: Incorporate the virtual engine into timeslicing
It was quite the oversight to only factor in the normal queue to decide
the timeslicing switch priority. By leaving out the next virtual request
from the priority decision, we would not timeslice the current engine if
there was an available virtual request.
Testcase: igt/gem_exec_balancer/sliced Fixes: 3df2deed411e ("drm/i915/execlists: Enable timeslice on partial virtual engine dequeue") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200519132046.22443-3-chris@chris-wilson.co.uk
Chris Wilson [Tue, 19 May 2020 13:20:45 +0000 (14:20 +0100)]
drm/i915/gt: Kick virtual siblings on timeslice out
If we decide to timeslice out the current virtual request, we will
unsubmit it while it is still busy (ve->context.inflight == sibling[0]).
If the virtual tasklet and then the other sibling tasklets run before we
completely schedule out the active virtual request for the preemption,
those other tasklets will see that the virtul request is still inflight
on sibling[0] and leave it be. Therefore when we finally schedule-out
the virtual request and if we see that we have passed it back to the
virtual engine, reschedule the virtual tasklet so that it may be
resubmitted on any of the siblings.
Chris Wilson [Tue, 19 May 2020 13:20:44 +0000 (14:20 +0100)]
drm/i915/selftests: Add tests for timeslicing virtual engines
Make sure that we can execute a virtual request on an already busy
engine, and conversely that we can execute a normal request if the
engines are already fully occupied by virtual requests.
Chris Wilson [Tue, 19 May 2020 06:31:15 +0000 (07:31 +0100)]
drm/i915/selftests: Check for an initial-breadcrumb in wait_for_submit()
When we look at i915_request_is_started() we must be careful in case we
are using a request that does not have the initial-breadcrumb and
instead the is-started is being compared against the end of the previous
request. This will make wait_for_submit() declare that a request has
been already submitted too early.
Chris Wilson [Tue, 19 May 2020 06:31:14 +0000 (07:31 +0100)]
drm/i915/selftests: Restore to default heartbeat
Since we temporarily disable the heartbeat and restore back to the
default value, we can use the stored defaults on the engine and avoid
using a local.
Chris Wilson [Tue, 19 May 2020 06:31:12 +0000 (07:31 +0100)]
drm/i915: Don't set queue-priority hint when supressing the reschedule
We recorded the execlists->queue_priority_hint update for the inflight
request without kicking the tasklet. The next submitted request then
failed to be scheduled as it had a lower priority than the hint, leaving
the HW running with only the inflight request.
Imre Deak [Thu, 14 May 2020 20:45:53 +0000 (23:45 +0300)]
drm/i915: Fix AUX power domain toggling across TypeC mode resets
Make sure to select the port's AUX power domain while holding the TC
port lock. The domain depends on the port's current TC mode, which may
get changed under us if we're not holding the lock.
This was left out from
commit 8c10e2262663 ("drm/i915: Keep the TypeC port mode fixed for detect/AUX transfers")
Ville Syrjälä [Thu, 14 May 2020 12:38:38 +0000 (15:38 +0300)]
drm/i915: Read out hrawclk on all gen3+ platforms
I've checked a bunch of gen3/4 machines and all seem to have
consistent FSB frequency information in the CLKCFG register.
So let's read out hrawclk on all gen3+ machines. Although
apart from g4x/pnv aux/pps dividers we only really need this
for for i965g/gm cs timestamp increment.
The CLKCFG memory clock values seem less consistent but we
don't care about those here.
For posterity here's a list of CLKCFG vs. FSB dumps from
a bunch of machines (only missing lpt for a full set):
machine CLKCFG FSB
alv1 0x00001411 533
alv2 0x00000420 400 (Chris)
gdg1 0x20000022 800
gdg2 0x20000022 800
cst 0x00010043 666
blb 0x00002034 1333
pnv1 0x00000423 666
pnv2 0x00000433 666
965gm 0x00004342 800
946gz 0x00000022 800
965g 0x00000422 800
g35 0x00000430 1066
0x00000434 1333
ctg1 0x00644056 1066
ctg2 0x00644066 1066
elk1 0x00012420 1066
0x00012424 1333
0x00012436 1600
0x00012422 800
elk2 0x00012040 1066
For the mobile parts the chipset docs generally have these
documented to some degree (alv being the exception).
The two settings w/o any evidence are 0x5=400MHz on desktop
and 0x7=1333MHz on mobile. Though the mobile 1333MHz case
probably doesn't even exist since ctg is only documented
to go up to 1066MHz.
v2: Fix 400mhz readout for Chris's alv/celeron machine
Do a clean mobile vs. dekstop split since that's really
what seems to be going on
Ville Syrjälä [Thu, 14 May 2020 12:38:37 +0000 (15:38 +0300)]
drm/i915: Document our lackluster FSB frequency readout
Document the fact that we aren't reading out the actual FSB
frequency but rather just the state of the FSB straps.
Some BIOSen allow you to configure the two independently.
So if someone sets the two up in an inconsistent manner
we'll get the wrong answer here and thus will end up with
incorrect aux/pps clock dividers. Alas, proper docs are no
longer around so we can't do any better.
Ville Syrjälä [Thu, 14 May 2020 12:38:36 +0000 (15:38 +0300)]
drm/i915: Fix 400 MHz FSB readout on elk
Looks like elk redefines some of the CLKCFG FSB values to
make room for 400 MHz FSB. The setting overlaps with one of
the 266MHz settings (which is even documented in the ctg docs,
and cofirmed to be correct on my ctg). So we limit the special
case to elk only.
Though it might also be that we have some kind of desktop vs.
mobile difference going on here as eg. both g35 and elk
use 0x0 for the 266 MHz setting, vs. 0x6 used by ctg). The
g35 doesn't let me select 400MHz for the FSB strap so can't
confirm which way it would go here. But anyways as it seems
only elk has the 400MHz option we shouldn't lose anything
by limiting the special case to it alone.
My earlier experiments on this appear to have been nonsense as
the comment I added claims that FSB strap of 400MHz results in
a value of 0x4, but I've now retested it and I definitely get a
value of 0x6 instead. So let's remove that bogus comment.
v2: s/_ELK/_ALT/ in the define in anticipation of a full
mobile vs. desktop CLKCFG split
Chris Wilson [Sat, 16 May 2020 19:09:40 +0000 (20:09 +0100)]
drm/i915/display: Return error from dbuf allocation failure
drivers/gpu/drm/i915/intel_pm.c:5920 skl_ddb_add_affected_pipes() error: uninitialized symbol 'ret'.
Fixes: 3cf43cdc63fb ("drm/i915: Introduce proper dbuf state") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200516190940.12675-1-chris@chris-wilson.co.uk
Ville Syrjälä [Mon, 18 May 2020 12:13:54 +0000 (15:13 +0300)]
drm/i915: Fix dbuf slice mask when turning off all the pipes
The current dbuf slice computation only happens when there are
active pipes. If we are turning off all the pipes we just leave
the dbuf slice mask at it's previous value, which may be something
other that BIT(S1). If runtime PM will kick in it will however
turn off everything but S1. Then on the next atomic commit (if
the new dbuf slice mask matches the stale value we left behind)
the code will not turn on the other slices we now need. This will
lead to underruns as the planes are trying to use a dbuf slice
that's not powered up.
To work around let's just just explicitly set the dbuf slice mask
to BIT(S1) when we are turning off all the pipes. Really the code
should just calculate this stuff the same way regardless whether
the pipes are on or off, but we're not quite there yet (need a
bit more work on the dbuf state for that).
Chris Wilson [Mon, 18 May 2020 10:29:11 +0000 (11:29 +0100)]
drm/i915/selftests: Refactor sibling selection
Tvrtko spotted that some selftests were using 'break' not 'continue',
which will fail for discontiguous engine layouts such as on Icelake
(which may have vcs0 and vcs2).
drm/i915: Mark check_shadow_context_ppgtt as maybe unused
When CONFIG_DRM_I915_DEBUG_GEM is not set, clang warns:
drivers/gpu/drm/i915/gvt/scheduler.c:884:1: warning: function
'check_shadow_context_ppgtt' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
check_shadow_context_ppgtt(struct execlist_ring_context *c, struct
intel_vgpu_mm *m)
^
1 warning generated.
This warning is similar to -Wunused-function but rather than warning
that the function is completely unused, it warns that it is used in some
expression within the file but that expression will be evaluated to a
constant or be optimized away in the final assembly, essentially making
it appeared used but really isn't. Usually, this happens when a function
or variable is only used in sizeof, where it will appear to be used but
will be evaluated at compile time and not be required to be emitted.
In this case, the function is only used in GEM_BUG_ON, which is defined
as BUILD_BUG_ON_INVALID, which intentionally follows this pattern. To
fix this warning, add __maybe_unused to make it clear that this is
intentional depending on the configuration.
Chris Wilson [Fri, 15 May 2020 20:00:31 +0000 (21:00 +0100)]
drm/i915/gem: Retry faulthandlers on ENOSPC
As we no longer use the shmemfs allocation directly, we do not expect to
receive -ENOSPC from a backing store allocation. The potential sources
for -ENOSPC are then our own internal eviction code, so the choice is
either to kill the potential application with SIGBUS or to retry the
faulthandler.
In this patch we retry the fault handler, but since this is a should
never happen condition, it is arguable that we gather up copious debug
and kill the application. At worst, we cause an interruptible busy-wait,
stalling the application -- all causes should be transient and the
system should eventually recover. A small stall is hopefully a better
outcome than random oomkiller.
Ville Syrjälä [Tue, 25 Feb 2020 17:11:16 +0000 (19:11 +0200)]
drm/i915: Clean up dbuf debugs during .atomic_check()
Combine the two per-pipe dbuf debugs into one, and use the canonical
[CRTC:%d:%s] style to identify the crtc. Also use the same style as
the plane code uses for the ddb start/end, and prefix bitmask properly
with 0x to make it clear they are in fact bitmasks.
The "how many total slices we are going to use" debug we move to
outside the crtc loop so it gets printed only once at the end.
Ville Syrjälä [Tue, 25 Feb 2020 17:11:15 +0000 (19:11 +0200)]
drm/i915: Move the dbuf pre/post plane update
Encapsulate the dbuf state more by moving the pre/post
plane functions out from intel_display.c. We stick them
into intel_pm.c since that's where the rest of the code
lives for now.
Eventually we should add a new file for this stuff at which
point we also need to decide if it makes sense to even split
the wm code from the ddb code, or to keep them together.
Ville Syrjälä [Tue, 25 Feb 2020 17:11:13 +0000 (19:11 +0200)]
drm/i915: Introduce proper dbuf state
Add a global state to track the dbuf slices. Gets rid of all the nasty
coupling between state->modeset and dbuf recomputation. Also we can now
totally nuke state->active_pipe_changes.
dev_priv->wm.distrust_bios_wm still remains, but that too will get
nuked soon.
Ville Syrjälä [Tue, 25 Feb 2020 17:11:11 +0000 (19:11 +0200)]
drm/i915: Polish some dbuf debugs
Polish some of the dbuf code to give more meaningful debug
messages and whatnot. Also we can switch over to the per-device
debugs/warns at the same time.
Ville Syrjälä [Tue, 25 Feb 2020 17:11:10 +0000 (19:11 +0200)]
drm/i915: Make skl_compute_dbuf_slices() behave consistently for all platforms
Currently skl_compute_dbuf_slices() returns 0 for any inactive pipe on
icl+, but returns BIT(S1) on pre-icl for any pipe (whether it's active or
not). Let's make the behaviour consistent and always return 0 for any
inactive pipe.
After the function is no longer marked 'inline', there
is now a new warning pointing out that the only caller
is inside of an #ifdef:
drivers/gpu/drm/i915/display/intel_panel.c:493:12: warning: 'scale_user_to_hw' defined but not used [-Wunused-function]
493 | static u32 scale_user_to_hw(struct intel_connector *connector,
| ^~~~~~~~~~~~~~~~
Move the function itself into that #ifdef as well.
Ville Syrjälä [Mon, 28 Oct 2019 11:30:35 +0000 (13:30 +0200)]
drm/i915: Enable pipe gamma for the overlay
We pass the plane data through the pipe gamma for all the other
planes. Can't see why we should treat the overlay differently,
so let's enable pipe gamma for it as well.
Ville Syrjälä [Mon, 28 Oct 2019 11:30:34 +0000 (13:30 +0200)]
drm/i915: Configure overlay cc_out precision based on crtc gamma config
Put the overlay color conversion unit into 10bit mode if the
pipe isn't using the 8bit legacy gamma. Not 100% sure this is
what the intention of the bit was but makes at least some sense to
me.
Ville Syrjälä [Mon, 28 Oct 2019 11:30:33 +0000 (13:30 +0200)]
drm/i915: Fix overlay colorkey for 30bpp and 8bpp
As with the video sprites the colorkey is always specified
as 8bpc. For 10bpc primary plane formats we just ignore the
two lsbs of each component. For C8 we'll replicate the same
key to each chanel, which is what the hardware wants.
Ville Syrjälä [Mon, 28 Oct 2019 11:30:32 +0000 (13:30 +0200)]
drm/i915: Fix max cursor size for i915g/gm
Apparently the 128x128 and 256x256 ARGB cursor modes were
only added on LPT/CST.
While the display section of bspec isn't super clear on the
subject, it does highlight these two modes in a different
color, has a few changlog entries indicating the 256x256 mode
was added for a LPT DCN, and that the 128x128 mode was also
added later (though no DCN/platform note there).
The "device dependencies" bspec section does list the 256x256x32
as a new feature for LPT/CST, and goes on to mention that current
hw only has the 64x64x32 mode (which reinforces the notion that
the 128x128 mode was also added at the same time).
Testing on actual hardware confirms all of this. CI shows all
the 128x128 and 256x256 tests failing on GDG, and my ALV
definitely doesn't like them.
So we shall limit GDG/ALV to 64x64 only. And while at it
let's adjust the mobile gen2 case to list the two platforms
explicitly so that the if-ladder looks reasonably uniform.
Joonas Lahtinen [Fri, 30 Aug 2019 10:50:53 +0000 (13:50 +0300)]
drm/i915: Document locking guidelines
To ensure cross-driver locking compatibility, document the expected
guidelines for implementing the GEM locking in i915. Note that this
is a description of how things should end up after being reworked,
and does not reflect the current state of things.
v2: Use rst note:: tag (Rodrigo)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Dave Airlie <airlied@redhat.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Cc: CQ Tang <cq.tang@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Acked-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190830105053.17491-1-joonas.lahtinen@linux.intel.com
Pull the code to do the CS timestamp ns<->ticks conversion into
helpers and use them all over.
The check in i915_perf_noa_delay_set() seems a bit dubious,
so we switch it to do what I assume it wanted to do all along
(ie. make sure the resulting delay in CS timestamp ticks
doesn't exceed 32bits)?
v3: Forbid simultaneous legacy SAGV PCode requests and
restricting qgv points. Put the actual restriction
to commit function, added serialization(thanks to Ville)
to prevent commit being applied out of order in case of
nonblocking and/or nomodeset commits.
v4:
- Minor code refactoring, fixed few typos(thanks to James Ausmus)
- Change the naming of qgv point
masking/unmasking functions(James Ausmus).
- Simplify the masking/unmasking operation itself,
as we don't need to mask only single point per request(James Ausmus)
- Reject and stick to highest bandwidth point if SAGV
can't be enabled(BSpec)
v5:
- Add new mailbox reply codes, which seems to happen during boot
time for TGL and indicate that QGV setting is not yet available.
v6:
- Increase number of supported QGV points to be in sync with BSpec.
v7: - Rebased and resolved conflict to fix build failure.
- Fix NUM_QGV_POINTS to 8 and moved that to header file(James Ausmus)
v8: - Don't report an error if we can't restrict qgv points, as SAGV
can be disabled by BIOS, which is completely legal. So don't
make CI panic. Instead if we detect that there is only 1 QGV
point accessible just analyze if we can fit the required bandwidth
requirements, but no need in restricting.
v9: - Fix wrong QGV transition if we have 0 planes and no SAGV
simultaneously.
v10: - Fix CDCLK corruption, because of global state getting serialized
without modeset, which caused copying of non-calculated cdclk
to be copied to dev_priv(thanks to Ville for the hint).
v11: - Remove unneeded headers and spaces(Matthew Roper)
- Remove unneeded intel_qgv_info qi struct from bw check and zero
out the needed one(Matthew Roper)
- Changed QGV error message to have more clear meaning(Matthew Roper)
- Use state->modeset_set instead of any_ms(Matthew Roper)
- Moved NUM_SAGV_POINTS from i915_reg.h to i915_drv.h where it's used
- Keep using crtc_state->hw.active instead of .enable(Matthew Roper)
- Moved unrelated changes to other patch(using latency as parameter
for plane wm calculation, moved to SAGV refactoring patch)
v12: - Fix rebase conflict with own temporary SAGV/QGV fix.
- Remove unnecessary mask being zero check when unmasking
qgv points as this is completely legal(Matt Roper)
- Check if we are setting the same mask as already being set
in hardware to prevent error from PCode.
- Fix error message when restricting/unrestricting qgv points
to "mask/unmask" which sounds more accurate(Matt Roper)
- Move sagv status setting to icl_get_bw_info from atomic check
as this should be calculated only once.(Matt Roper)
- Edited comments for the case when we can't enable SAGV and
use only 1 QGV point with highest bandwidth to be more
understandable.(Matt Roper)
v13: - Moved max_data_rate in bw check to closer scope(Ville Syrjälä)
- Changed comment for zero new_mask in qgv points masking function
to better reflect reality(Ville Syrjälä)
- Simplified bit mask operation in qgv points masking function
(Ville Syrjälä)
- Moved intel_qgv_points_mask closer to gen11 SAGV disabling,
however this still can't be under modeset condition(Ville Syrjälä)
- Packed qgv_points_mask as u8 and moved closer to pipe_sagv_mask
(Ville Syrjälä)
- Extracted PCode changes to separate patch.(Ville Syrjälä)
- Now treat num_planes 0 same as 1 to avoid confusion and
returning max_bw as 0, which would prevent choosing QGV
point having max bandwidth in case if SAGV is not allowed,
as per BSpec(Ville Syrjälä)
- Do the actual qgv_points_mask swap in the same place as
all other global state parts like cdclk are swapped.
In the next patch, this all will be moved to bw state as
global state, once new global state patch series from Ville
lands
v14: - Now using global state to serialize access to qgv points
- Added global state locking back, otherwise we seem to read
bw state in a wrong way.
v15: - Added TODO comment for near atomic global state locking in
bw code.
v16: - Fixed intel_atomic_bw_* functions to be intel_bw_* as discussed
with Jani Nikula.
- Take bw_state_changed flag into use.
v17: - Moved qgv point related manipulations next to SAGV code, as
those are semantically related(Ville Syrjälä)
- Renamed those into intel_sagv_(pre)|(post)_plane_update
(Ville Syrjälä)
v18: - Move sagv related calls from commit tail into
intel_sagv_(pre)|(post)_plane_update(Ville Syrjälä)
v19: - Use intel_atomic_get_bw_(old)|(new)_state which is intended
for commit tail stage.
v20: - Return max bandwidth for 0 planes(Ville)
- Constify old_bw_state in bw_atomic_check(Ville)
- Removed some debugs(Ville)
- Added data rate to debug print when no QGV points(Ville)
- Removed some comments(Ville)
v21, v22, v23: - Fixed rebase conflict
v24: - Changed PCode mask to use ICL_ prefix
v25: - Resolved rebase conflict
v27: - Use device specific drm_err(Ville)
- Fixed parenthesis ident reported by checkpatch
Line over 100 warns to be fixed together with
existing code style.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Cc: Ville Syrjälä <ville.syrjala@intel.com> Cc: James Ausmus <james.ausmus@intel.com>
[vsyrjala: Drop duplicate intel_sagv_{pre,post}_plane_update() prototypes
and drop unused NUM_SAGV_POINTS define] Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-3-stanislav.lisovskiy@intel.com
Starting from TGL we need to have a separate wm0
values for SAGV and non-SAGV which affects
how calculations are done.
v2: Remove long lines
v3: Removed COLOR_PLANE enum references
v4, v5, v6: Fixed rebase conflict
v7: - Removed skl_plane_wm_level accessor from skl_allocate_pipe_ddb(Ville)
- Removed sagv_uv_wm0(Ville)
- can_sagv->use_sagv_wm(Ville)
v8: - Moved tgl_crtc_can_enable_sagv function up(Ville)
- Changed comment regarding pipe_wm usage(Ville)
- Call intel_can_enable_sagv and tgl_compute_sagv_wm only
for Gen12(Ville)
- Some sagv debugs removed(Ville)
- skl_print_wm_changes improvements(Ville)
- Do assignment instead of memcpy in
skl_pipe_wm_get_hw_state(Ville)
v9: - Removed can_sagv variable(Ville)
- Removed spurious line(Ville)
- Changed u32 to unsigned int as agreed(Ville)
- Assign sagv only for gen12 in
skl_pipe_wm_get_hw_state(Ville)
Joonas Lahtinen [Thu, 14 May 2020 15:02:22 +0000 (18:02 +0300)]
Merge tag 'gvt-next-2020-05-12' of https://github.com/intel/gvt-linux into drm-intel-next-queued
gvt-next-2020-05-12
- Support PPGTT update via LRI cmd (Zhenyu)
- Remove extra kmap for shadow ctx update (Zhenyu)
- Move workload cleanup out of execlist handling code (Zhenyu)
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:32 +0000 (09:07 +0300)]
drm/i915/psr: Use new DP VSC SDP compute routine on PSR
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.
In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.
There are no changes to PSR mechanism.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
infoframes.enable.
It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:31 +0000 (09:07 +0300)]
drm/i915/dp: Add compute routine for DP PSR VSC SDP
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it adds a compute routine for PSR VSC SDP.
As PSR routine can not use infoframes.vsc of crtc state, it also adds new
writing of DP SDPs (Secondary Data Packet) for PSR.
PSR routine has its own scenario and timings of writing a VSC SDP.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: 1) Fix packing of VSC SDP where Pixel Encoding/Colorimetry Format is
not supported.
2) Change a checking of PSR state.
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:29 +0000 (09:07 +0300)]
drm/i915: Program DP SDPs on pipe updates
Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:28 +0000 (09:07 +0300)]
drm/i915: Fix enabled infoframe states of lspcon
Compared to implementation of DP and HDMI's encoder->infoframes_enabled,
the lspcon's implementation returns its active state. (we expect enabled
infoframe states of HW.) It leads to pipe state mismatch error
when ddi_get_config is called.
Because the current implementation of lspcon is not ready to support
readout infoframes, we need to return 0 here.
In order to support readout to lspcon, we need to implement read_infoframe
and infoframes_enabled. And set_infoframes also have to set an appropriate
bit on crtc_state->infoframes.enable
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:27 +0000 (09:07 +0300)]
drm/i915: Add state readout for DP VSC SDP
Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:25 +0000 (09:07 +0300)]
drm/i915: Program DP SDPs with computed configs
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:20 +0000 (09:07 +0300)]
drm/i915/dp: Read out DP SDPs
It adds code to read the DP SDPs from the video DIP and unpack them into
the crtc state.
It adds routines that read out DP VSC SDP and DP HDR Metadata Infoframe SDP
In order to unpack DP VSC SDP, it adds intel_dp_vsc_sdp_unpack() function.
It follows DP 1.4a spec. [Table 2-116: VSC SDP Header Bytes] and
[Table 2-117: VSC SDP Payload for DB16 through DB18]
In order to unpack DP HDR Metadata Infoframe SDP, it adds
intel_dp_hdr_metadata_infoframe_sdp_unpack(). And it follows DP 1.4a spec.
([Table 2-125: INFOFRAME SDP v1.2 Header Bytes] and
[Table 2-126: INFOFRAME SDP v1.2 Payload Data Bytes - DB0 through DB31])
and CTA-861-G spec. [Table-42 Dynamic Range and Mastering InfoFrame].
A naming rule and style of intel_read_dp_sdp() function references
intel_read_infoframe() function of intel_hdmi.c
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v5: Addressed review comments from Uma
- Polish commit message and comments
- Combine the if checks of sdp.HB2 and sdp.HB3
- Add 6bpc to unpacking of VSC SDP
Gwan-gyeong Mun [Thu, 14 May 2020 06:07:19 +0000 (09:07 +0300)]
video/hdmi: Add Unpack only function for DRM infoframe
It adds an unpack only function for DRM infoframe for dynamic range and
mastering infoframe readout.
It unpacks the information data block contained in the binary buffer into
a structured frame of the HDMI Dynamic Range and Mastering (DRM)
information frame.
In contrast to hdmi_drm_infoframe_unpack() function, it does not verify
a checksum.
It can be used for unpacking a DP HDR Metadata Infoframe SDP case.
DP HDR Metadata Infoframe SDP uses the same Dynamic Range and Mastering
(DRM) information (CTA-861-G spec.) such as HDMI DRM infoframe.
But DP SDP header and payload structure are different from HDMI DRM
Infoframe. Therefore unpacking DRM infoframe for DP requires skipping of
a verifying checksum.
v9: Add clear comments to hdmi_drm_infoframe_unpack_only() and
hdmi_drm_infoframe_unpack() (Laurent Pinchart)
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-2-gwan-gyeong.mun@intel.com
Chris Wilson [Wed, 13 May 2020 07:47:46 +0000 (08:47 +0100)]
drm/i915/gt: Transfer old virtual breadcrumbs to irq_worker
The second try at staging the transfer of the breadcrumb. In part one,
we realised we could not simply move to the second engine as we were
only holding the breadcrumb lock on the first. So in commit 6c81e21a4742
("drm/i915/gt: Stage the transfer of the virtual breadcrumb"), we
removed it from the first engine and marked up this request to reattach
the signaling on the new engine. However, this failed to take into
account that we only attach the breadcrumb if the new request is added
at the start of the queue, which if we are transferring, it is because
we know there to be a request to be signaled (and hence we would not be
attached).
In this attempt, we try to transfer the completed requests to the
irq_worker on its rq->engine->breadcrumbs. This preserves the coupling
between the rq and its breadcrumbs, so that
i915_request_cancel_breadcrumb() does not attempt to manipulate the list
under the wrong lock.
v2: Code sharing is fun.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1862 Fixes: 6c81e21a4742 ("drm/i915/gt: Stage the transfer of the virtual breadcrumb") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200513074809.18194-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 14 May 2020 06:29:05 +0000 (07:29 +0100)]
drm/i915: Show per-engine default property values in sysfs
By providing the default values configured into the kernel via sysfs, it
is much more convenient for userspace to restore those sane defaults, or
at least know what are considered good baseline. This is useful, for
example, to cleanup after any failed userspace prior to commencing new
jobs.
Chris Wilson [Wed, 13 May 2020 17:35:04 +0000 (18:35 +0100)]
drm/i915: Drop no-semaphore boosting
Now that we have fast timeslicing on semaphores, we no longer need to
prioritise none-semaphore work as we will yield any work blocked on a
semaphore to the next in the queue. Previously with no timeslicing,
blocking on the semaphore caused extremely bad scheduling with multiple
clients utilising multiple rings. Now, there is no impact and we can
remove the complication.
Chris Wilson [Wed, 13 May 2020 07:47:59 +0000 (08:47 +0100)]
drm/i915: Drop I915_RESET_TIMEOUT and friends
These were used to set various timeouts for the reset procedure
(deciding when the engine was dead, and even if the reset itself was not
making forward progress). No longer used.
Chris Wilson [Wed, 13 May 2020 16:59:32 +0000 (17:59 +0100)]
drm/i915: Mark the addition of the initial-breadcrumb in the request
The initial-breadcrumb is used to mark the end of the awaiting and the
beginning of the user payload. We verify that we do not start the user
payload before all signaler are completed, checking our semaphore setup
by looking for the initial breadcrumb being written too early. We also
want to ensure that we do not add semaphore waits after we have already
closed the semaphore section, an issue for later deferred waits.
Chris Wilson [Wed, 13 May 2020 12:28:26 +0000 (13:28 +0100)]
drm/i915/gt: Suspend tasklets before resume sanitization
It is possible for a residual tasklet to be pending execution as we
resume (whether that's some prior test kicking off the tasklet, or if we
are in a suspend/resume stress test). As such, we do not want that
tasklet to execute in the middle of our sanitization, such that it sees
the poisoned state. For example,
As part of the reset preparation, engine->reset.prepare() prevents the
tasklet from running, so pull the sanitization inside the critical
section for reset.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/1812 Fixes: 23122a4d992b ("drm/i915/gt: Scrub execlists state on resume") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200513122826.27484-1-chris@chris-wilson.co.uk
For future Gen12 SAGV implementation we need to
seemlessly alter wm levels calculated, depending
on whether we are allowed to enable SAGV or not.
So this accessor will give additional flexibility
to do that.
Currently this accessor is still simply working
as "pass-through" function. This will be changed
in next coming patches from this series.
v2: - plane_id -> plane->id(Ville Syrjälä)
- Moved wm_level var to have more local scope
(Ville Syrjälä)
- Renamed yuv to color_plane(Ville Syrjälä) in
skl_plane_wm_level
v3: - plane->id -> plane_id(this time for real, Ville Syrjälä)
- Changed colorplane id type from boolean to int as index
(Ville Syrjälä)
- Moved crtc_state param so that it is first now
(Ville Syrjälä)
- Moved wm_level declaration to tigher scope in
skl_write_plane_wm(Ville Syrjälä)
v4: - Started to use enum values for color plane
- Do sizeof for a type what we are memset'ing
- Zero out wm_uv as well(Ville Syrjälä)
v5: - Fixed rebase conflict caused by COLOR_PLANE_*
enum removal
v6: - Do not use skl_plane_wm_level accessor in skl_allocate_pipe_ddb
v7: - Get rid of wm_uv, which is not used in skl_plane_write_wm(Ville)
Chris Wilson [Wed, 13 May 2020 10:01:20 +0000 (11:01 +0100)]
drm/i915/gt: Reset execlists registers before HWSP
Upon gt resume, we first poison then sanitize the engine. However, our
testing shows that gen9 will very rarely retain the poisoned value from
the HWSP mappings of the execlists status registers. This suggests that
it is reading back from the HWSP, so rejig the register reset.
v2: Maybe RING_CONTEXT_STATUS_PTR is write masked. It is.
projects / mirror_ubuntu-jammy-kernel.git / log