* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
connector: Delete buggy notification code.
be2net: use eq-id to calculate cev-isr reg offset
Bluetooth: Use the control channel for raw HID reports
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Bluetooth: Fix memory leak in L2CAP
Bluetooth: Remove double free of SKB pointer in L2CAP
cdc_ether: Partially revert "usbnet: Set link down initially ..."
be2net: Fix memset() arg ordering.
bonding: bond_open error return value
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
ixgbe: set the correct DCB bit for pg tx settings
igbvf: fix issue w/ mapped_as_page being left set after unmap
drivers/net: ks8851_mll ethernet network driver
be2net: Bug fix to support newer generation of BE ASIC
starfire: clean up properly if firmware loading fails
mac80211: fix NULL pointer dereference when ftrace is enabled
netfilter: ctnetlink: fix expectation mask dump
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
ath9k: fix eeprom INI values override for 2GHz-only cards
...
pktcdvd: removing device does not remove its sysfs dir
This is the counterpart to cba767175becadc5c4016cceb7bfdd2c7fe722f4
("pktcdvd: remove broken dev_t export of class devices"). Device is not
registered using dev_t, so it should not be destroyed using device_destroy
which looks up the device by dev_t. This will fail and adding the device
again will fail with the "duplicate name" error. This is fixed using
device_unregister instead of device_destroy.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Peter Osterlund <petero2@telia.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Röjfors [Tue, 2 Feb 2010 21:44:12 +0000 (13:44 -0800)]
uartlite: fix crash when using as console
Move the ulite_console_setup to the .devinit section since it might be
called on probe, which is in devinit. Fixes the crash below where the
uartlite hw is probed after the .init section is freed from the kernel.
uartlite: ttyUL0 at MMIO 0xc8000100 (irq = 30) is a uartlite
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c176720e>] ulite_console_setup+0x6f/0xa8
*pdpt = 0000000036fb0001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1f.1/host0/uevent
Modules linked in: puffin(+) serio_raw
imxfb: correct location of callbacks in suspend and resume
The probe function passes a pointer to a struct fb_info to
platform_set_drvdata(), so don't interpret the return value of
platform_get_drvdata() as a pointer to struct imxfb_info.
The original imxfb_info *fbi backlight_power was NULL but in imxfb_suspend
it was 4 resulting in an oops as imxfb_suspend calls
imxfb_disable_controller(fbi) which in turn has
if (fbi->backlight_power)
fbi->backlight_power(0);
Li Zefan [Tue, 2 Feb 2010 21:44:10 +0000 (13:44 -0800)]
cgroups: fix to return errno in a failure path
In cgroup_create(), if alloc_css_id() returns failure, the errno is not
propagated to userspace, so mkdir will fail silently.
To trigger this bug, we mount blkio (or memory subsystem), and create more
then 65534 cgroups. (The number of cgroups is limited to 65535 if a
subsystem has use_id == 1)
# mount -t cgroup -o blkio xxx /mnt
# for ((i = 0; i < 65534; i++)); do mkdir /mnt/$i; done
# mkdir /mnt/65534
(should return ENOSPC)
#
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Acked-by: Paul Menage <menage@google.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hui Zhu [Tue, 2 Feb 2010 21:44:09 +0000 (13:44 -0800)]
markup_oops.pl: fix $func_offset error with x86_64
When I use markup_oops.pl parse a x8664 oops, I got:
objdump: --start-address: bad number: NaN
No matching code found
This is because:
main::(./m.pl:228): open(FILE, "objdump -dS --adjust-vma=$vmaoffset --start-address=$decodestart --stop-address=$decodestop $filename |") || die "Cannot start objdump";
DB<3> p $decodestart
NaN
This NaN is from:
main::(./m.pl:176): my $decodestart = Math::BigInt->from_hex("0x$target") - Math::BigInt->from_hex("0x$func_offset");
DB<2> p $func_offset
0x175
There is already a "0x" in $func_offset, another 0x makes it a NaN.
I make a patch to change "(0x[0-9a-f]+)\/0x[a-f0-9]/)" to "0x([0-9a-f]+)\/0x[a-f0-9]/)".
Signed-off-by: Hui Zhu <teawater@gmail.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Kennedy [Tue, 2 Feb 2010 21:44:07 +0000 (13:44 -0800)]
get_maintainer.pl: teach git log to use --no-color
When git has been set to always use color in .gitconfig then I get the
warning message
Bad divisor in main::vcs_assign: 0
This is caused by vcs_file_signoffs not matching any commits due to the
pattern not understand the colour codes. Fix this by telling git log to
never use colour.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Acked-by: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wu Fengguang [Tue, 2 Feb 2010 21:44:06 +0000 (13:44 -0800)]
devmem: fix kmem write bug on memory holes
write_kmem() used to assume vwrite() always return the full buffer length.
However now vwrite() could return 0 to indicate memory hole. This
creates a bug that "buf" is not advanced accordingly.
Fix it to simply ignore the return value, hence the memory hole.
This also makes the kmem read/write implementation aligned with mem(4):
"References to nonexistent locations cause errors to be returned." Here we
return -ENXIO (inspired by Hugh) if no bytes have been transfered to/from
user space, otherwise return partial read/write results.
anfei zhou [Tue, 2 Feb 2010 21:44:02 +0000 (13:44 -0800)]
mm: flush dcache before writing into page to avoid alias
The cache alias problem will happen if the changes of user shared mapping
is not flushed before copying, then user and kernel mapping may be mapped
into two different cache line, it is impossible to guarantee the coherence
after iov_iter_copy_from_user_atomic. So the right steps should be:
flush_dcache_page(page);
kmap_atomic(page);
write to page;
kunmap_atomic(page);
flush_dcache_page(page);
More precisely, we might create two new APIs flush_dcache_user_page and
flush_dcache_kern_page to replace the two flush_dcache_page accordingly.
Here is a snippet tested on omap2430 with VIPT cache, and I think it is
not ARM-specific:
Randy Dunlap [Tue, 2 Feb 2010 21:44:01 +0000 (13:44 -0800)]
kfifo: fix kernel-doc notation
Fix kfifo kernel-doc warnings:
Warning(kernel/kfifo.c:361): No description found for parameter 'total'
Warning(kernel/kfifo.c:402): bad line: @ @lenout: pointer to output variable with copied data
Warning(kernel/kfifo.c:412): No description found for parameter 'lenout'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Stefani Seibold <stefani@seibold.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alberto Panizzo [Tue, 2 Feb 2010 21:43:59 +0000 (13:43 -0800)]
mx3fb: some debug and initialisation fixes
Fix the kernel oops when dev_dbg is called with mx3_fbi->txd == NULL
Fix the late initialisation of mx3fb->backlight_level. If not, in the
chain of function started by init_fb_chan(), in __blank() call
sdc_set_brightness(mx3fb, mx3fb->backlight_level) that will shut down the
CONTRAST PWM output.
Tejun Heo [Tue, 2 Feb 2010 21:43:58 +0000 (13:43 -0800)]
idr: fix a critical misallocation bug
Eric Paris located a bug in idr. With IDR_BITS of 6, it grows to three
layers when id 4096 is first allocated. When that happens, idr wraps
incorrectly and searches the idr array ignoring the high bits. The
following test code from Eric demonstrates the bug nicely.
int init_module(void)
{
int ret, forty95, forty96;
void *addr;
/* add 2 entries both with 4095 as the start address */
again1:
if (!idr_pre_get(&test_idr, GFP_KERNEL))
return -ENOMEM;
ret = idr_get_new_above(&test_idr, (void *)4095, 4095, &forty95);
if (ret) {
if (ret == -EAGAIN)
goto again1;
return ret;
}
if (forty95 != 4095)
printk(KERN_ERR "hmmm, forty95=%d\n", forty95);
again2:
if (!idr_pre_get(&test_idr, GFP_KERNEL))
return -ENOMEM;
ret = idr_get_new_above(&test_idr, (void *)4096, 4095, &forty96);
if (ret) {
if (ret == -EAGAIN)
goto again2;
return ret;
}
if (forty96 != 4096)
printk(KERN_ERR "hmmm, forty96=%d\n", forty96);
/* try to find the 2 entries, noticing that 4096 broke */
addr = idr_find(&test_idr, forty95);
if ((int)addr != forty95)
printk(KERN_ERR "hmmm, after find forty95=%d addr=%d\n", forty95, (int)addr);
addr = idr_find(&test_idr, forty96);
if ((int)addr != forty96)
printk(KERN_ERR "hmmm, after find forty96=%d addr=%d\n", forty96, (int)addr);
/* really weird, the entry which should be at 4096 is actually at 0!! */
addr = idr_find(&test_idr, 0);
if ((int)addr)
printk(KERN_ERR "found an entry at id=0 for addr=%d\n", (int)addr);
MODULE_AUTHOR("Eric Paris <eparis@redhat.com>");
MODULE_DESCRIPTION("Simple idr test");
MODULE_LICENSE("GPL");
This happens because when sub_alloc() back tracks it doesn't always do it
step-by-step while the over-the-limit detection assumes step-by-step
backtracking. The logic in sub_alloc() looks like the following.
restart:
clear pa[top level + 1] for end cond detection
l = top level
while (true) {
search for empty slot at this level
if (not found) {
push id to the next possible value
l++
A: if (pa[l] is clear)
failed, return asking caller to grow the tree
if (going up 1 level gives more slots to search)
continue the while loop above with the incremented l
else
C: goto restart
}
adjust id accordingly to the found slot
if (l == 0)
return found id;
create lower level if not there yet
record pa[l] and l--
}
Test A is the fail exit condition but this assumes that failure is
propagated upwared one level at a time but the B optimization path breaks
the assumption and restarts the whole thing with a start value which is
above the possible limit with the current layers. sub_alloc() assumes the
start id value is inside the limit when called and test A is the only exit
condition check, so it ends up searching for empty slot while ignoring
high set bit.
So, for 4095->4096 test, level0 search fails but pa[1] contains a valid
pointer. However, going up 1 level wouldn't give any more empty slot so
it takes C and when the whole thing restarts nobody notices the high bit
set beyond the top level.
This patch fixes the bug by changing the fail exit condition check to full
id limit check.
Based-on-patch-from: Eric Paris <eparis@redhat.com> Reported-by: Eric Paris <eparis@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 2 Feb 2010 20:54:37 +0000 (12:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Do not idle on async queues
blk-cgroup: Fix potential deadlock in blk-cgroup
block: fix bugs in bio-integrity mempool usage
block: fix bio_add_page for non trivial merge_bvec_fn case
drbd: null dereference bug
drbd: fix max_segment_size initialization
Nick Piggin [Mon, 1 Feb 2010 11:25:57 +0000 (22:25 +1100)]
mm: purge fragmented percpu vmap blocks
Improve handling of fragmented per-CPU vmaps. We previously don't free
up per-CPU maps until all its addresses have been used and freed. So
fragmented blocks could fill up vmalloc space even if they actually had
no active vmap regions within them.
Add some logic to allow all CPUs to have these blocks purged in the case
of failure to allocate a new vm area, and also put some logic to trim
such blocks of a current CPU if we hit them in the allocation path (so
as to avoid a large build up of them).
Christoph reported some vmap allocation failures when using the per CPU
vmap APIs in XFS, which cannot be reproduced after this patch and the
previous bug fix.
Cc: linux-mm@kvack.org Cc: stable@kernel.org Tested-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Nick Piggin <npiggin@suse.de>
-- Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Mon, 1 Feb 2010 11:24:18 +0000 (22:24 +1100)]
mm: percpu-vmap fix RCU list walking
RCU list walking of the per-cpu vmap cache was broken. It did not use
RCU primitives, and also the union of free_list and rcu_head is
obviously wrong (because free_list is indeed the list we are RCU
walking).
While we are there, remove a couple of unused fields from an earlier
iteration.
These APIs aren't actually used anywhere, because of problems with the
XFS conversion. Christoph has now verified that the problems are solved
with these patches. Also it is an exported interface, so I think it
will be good to be merged now (and Christoph wants to get the XFS
changes into their local tree).
Cc: stable@kernel.org Cc: linux-mm@kvack.org Tested-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Nick Piggin <npiggin@suse.de>
-- Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 2 Feb 2010 20:47:51 +0000 (12:47 -0800)]
Merge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix access to released memory in clk_debugfs_register_one()
sh: Fix access to released memory in dwarf_unwinder_cleanup()
usb: r8a66597-hdc disable interrupts fix
spi: spi_sh_msiof: Fixed data sampling on the correct edge
Linus Torvalds [Tue, 2 Feb 2010 20:37:44 +0000 (12:37 -0800)]
Fix 'flush_old_exec()/setup_new_exec()' split
Commit 221af7f87b9 ("Split 'flush_old_exec' into two functions") split
the function at the point of no return - ie right where there were no
more error cases to check. That made sense from a technical standpoint,
but when we then also combined it with the actual personality setting
going in between flush_old_exec() and setup_new_exec(), it needs to be a
bit more careful.
In particular, we need to make sure that we really flush the old
personality bits in the 'flush' stage, rather than later in the 'setup'
stage, since otherwise we might be flushing the _new_ personality state
that we're just setting up.
So this moves the flags and personality flushing (and 'flush_thread()',
which is the arch-specific function that generally resets lazy FP state
etc) of the old process into flush_old_exec(), so that it doesn't affect
any state that execve() is setting up for the new process environment.
This was reported by Michal Simek as breaking his Microblaze qemu
environment.
Reported-and-tested-by: Michal Simek <michal.simek@petalogix.com> Cc: Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vivek Goyal [Tue, 2 Feb 2010 19:45:46 +0000 (20:45 +0100)]
cfq-iosched: Do not idle on async queues
Few weeks back, Shaohua Li had posted similar patch. I am reposting it
with more test results.
This patch does two things.
- Do not idle on async queues.
- It also changes the write queue depth CFQ drives (cfq_may_dispatch()).
Currently, we seem to driving queue depth of 1 always for WRITES. This is
true even if there is only one write queue in the system and all the logic
of infinite queue depth in case of single busy queue as well as slowly
increasing queue depth based on last delayed sync request does not seem to
be kicking in at all.
This patch will allow deeper WRITE queue depths (subjected to the other
WRITE queue depth contstraints like cfq_quantum and last delayed sync
request).
Shaohua Li had reported getting more out of his SSD. For me, I have got
one Lun exported from an HP EVA and when pure buffered writes are on, I
can get more out of the system. Following are test results of pure
buffered writes (with end_fsync=1) with vanilla and patched kernel. These
results are average of 3 sets of run with increasing number of threads.
I also ran buffered writes along with some sequential reads and some
buffered reads going on in the system on a SATA disk because the potential
risk could be that we should not be driving queue depth higher in presence
of sync IO going to keep the max clat low.
With some random and sequential reads going on in the system on one SATA
disk I did not see any significant increase in max clat. So it looks like
other WRITE queue depth control logic is doing its job. Here are the
results.
Sathya Perla [Tue, 2 Feb 2010 15:48:40 +0000 (07:48 -0800)]
be2net: use eq-id to calculate cev-isr reg offset
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Damm [Wed, 27 Jan 2010 07:41:19 +0000 (07:41 +0000)]
usb: r8a66597-hdc disable interrupts fix
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Markus Pietrek [Tue, 2 Feb 2010 02:29:15 +0000 (11:29 +0900)]
spi: spi_sh_msiof: Fixed data sampling on the correct edge
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Herbert Xu [Sun, 31 Jan 2010 22:17:56 +0000 (09:17 +1100)]
crypto: padlock-sha - Add import/export support
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Matt Mackall [Fri, 29 Jan 2010 08:50:36 +0000 (21:50 +1300)]
random: drop weird m_time/a_time manipulation
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Manuel Lauss [Tue, 26 Jan 2010 19:39:33 +0000 (20:39 +0100)]
MIPS: Alchemy: Fix dbdma ring destruction memory debugcheck.
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org> Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Mon, 1 Feb 2010 18:57:12 +0000 (10:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: AM3517: ASoC driver not getting compiled
ASoC: AIC23: Fixing writes to non-existing registers in resume function
ALSA: hda - Add an ASUS mobo to MSI blacklist
Linus Torvalds [Mon, 1 Feb 2010 18:46:49 +0000 (10:46 -0800)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
Linus Torvalds [Mon, 1 Feb 2010 18:45:00 +0000 (10:45 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
hw_breakpoints: Release the bp slot if arch_validate_hwbkpt_settings() fails.
perf: Ignore perf.data.old
perf report: Fix segmentation fault when running with '-g none'
Linus Torvalds [Mon, 1 Feb 2010 18:44:36 +0000 (10:44 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Correct printk whitespace in warning from cpu down task check
sched: Fix incorrect sanity check
sched: Fix fork vs hotplug vs cpuset namespaces
Linus Torvalds [Mon, 1 Feb 2010 18:43:01 +0000 (10:43 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/documentation: Cover new frame pointer semantics
tracing/documentation: Fix a typo in ftrace.txt
ring-buffer: Check for end of page in iterator
ring-buffer: Check if ring buffer iterator has stale data
tracing: Prevent kernel oops with corrupted buffer
Linus Torvalds [Mon, 1 Feb 2010 18:42:35 +0000 (10:42 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
Mark Brown [Mon, 4 Jan 2010 15:30:54 +0000 (15:30 +0000)]
regulator: Specify REGULATOR_CHANGE_STATUS for WM835x LED constraints
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ince gfs2 writes the rindex file a block at a time, and releases the
exclusive lock after each block, it is possible that another process
will grab the lock in the middle of the write. Since rindex entries are
not an even divisor of blocks, that other process may see partial
entries. On grows, this is fine. The process can simply ignore the the
partial entires. Previously, the code withdrew when it saw partial
entries. Now it simply ignores them.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Michel Dänzer [Fri, 22 Jan 2010 08:20:00 +0000 (09:20 +0100)]
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 1 Feb 2010 01:35:47 +0000 (11:35 +1000)]
drm/radeon/kms: move radeon KMS on/off switch out of staging.
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Jerome Glisse [Fri, 22 Jan 2010 14:19:00 +0000 (15:19 +0100)]
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Peter Hanzel [Sat, 30 Jan 2010 03:38:07 +0000 (03:38 +0000)]
drm/vmwgfx: Request SVGA version 2 and bail if not found
This fixes the driver not loading on older versions of VMware.
Signed-off-by: Peter Hanzel <hanzelpeter@gmail.com> Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Richard Kennedy [Tue, 26 Jan 2010 17:10:48 +0000 (17:10 +0000)]
drm/ttm: remove padding from ttm_ref_object on 64bit builds
Re-order structure ttm_ref_object to remove 8 bytes of alignment padding
on 64 bit builds, so shrinking its size from 72 to 64 bytes allowing it
to fit into a smaller slab.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Acked-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
John Kacur [Sun, 31 Jan 2010 19:38:03 +0000 (20:38 +0100)]
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
First call drm_agp_acquire to check if agp has been acquired.
Second call drm_agp_info to fill in the info data struct, including aper_size.
Finally do the check to see if the aper_size makes sense.
Signed-off-by: John Kacur <jkacur@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.
This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.
V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.
V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.
Bastien Nocera [Wed, 20 Jan 2010 12:00:42 +0000 (12:00 +0000)]
Bluetooth: Use the control channel for raw HID reports
In commit 2da31939a42f7a676a0bc5155d6a0a39ed8451f2, support
for Bluetooth hid_output_raw_report was added, but it pushes
the data to the interrupt channel instead of the contol one.
This patch makes hid_output_raw_report use the control channel
instead. Using the interrupt channel was a mistake.
Mike Frysinger [Mon, 14 Sep 2009 17:43:49 +0000 (13:43 -0400)]
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Commit ac019360fe3 changed the irq handler logic to BUG_ON rather than
returning IRQ_NONE when the incoming argument is invalid. While this
works in most cases, it doesn't work when the IRQ is shared with other
devices (or when DEBUG_SHIRQ is enabled).
So revert the previous change and replace the warning message with a
comment explaining that we want this behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jason Wessel [Thu, 28 Jan 2010 23:04:43 +0000 (17:04 -0600)]
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
This patch fixes the regression in functionality where the
kernel debugger and the perf API do not nicely share hw
breakpoint reservations.
The kernel debugger cannot use any mutex_lock() calls because it
can start the kernel running from an invalid context.
A mutex free version of the reservation API needed to get
created for the kernel debugger to safely update hw breakpoint
reservations.
The possibility for a breakpoint reservation to be concurrently
processed at the time that kgdb interrupts the system is
improbable. Should this corner case occur the end user is
warned, and the kernel debugger will prohibit updating the
hardware breakpoint reservations.
Any time the kernel debugger reserves a hardware breakpoint it
will be a system wide reservation.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: kgdb-bugreport@lists.sourceforge.net Cc: K.Prasad <prasad@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-3-git-send-email-jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jason Wessel [Thu, 28 Jan 2010 23:04:42 +0000 (17:04 -0600)]
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
In the 2.6.33 kernel, the hw_breakpoint API is now used for the
performance event counters. The hw_breakpoint_handler() now
consumes the hw breakpoints that were previously set by kgdb
arch specific code. In order for kgdb to work in conjunction
with this core API change, kgdb must use some of the low level
functions of the hw_breakpoint API to install, uninstall, and
deal with hw breakpoint reservations.
The kgdb core required a change to call kgdb_disable_hw_debug
anytime a slave cpu enters kgdb_wait() in order to keep all the
hw breakpoints in sync as well as to prevent hitting a hw
breakpoint while kgdb is active.
During the architecture specific initialization of kgdb, it will
pre-allocate 4 disabled (struct perf event **) structures. Kgdb
will use these to manage the capabilities for the 4 hw
breakpoint registers, per cpu. Right now the hw_breakpoint API
does not have a way to ask how many breakpoints are available,
on each CPU so it is possible that the install of a breakpoint
might fail when kgdb restores the system to the run state. The
intent of this patch is to first get the basic functionality of
hw breakpoints working and leave it to the person debugging the
kernel to understand what hw breakpoints are in use and what
restrictions have been imposed as a result. Breakpoint
constraints will be dealt with in a future patch.
While atomic, the x86 specific kgdb code will call
arch_uninstall_hw_breakpoint() and arch_install_hw_breakpoint()
to manage the cpu specific hw breakpoints.
The net result of these changes allow kgdb to use the same pool
of hw_breakpoints that are used by the perf event API, but
neither knows about future reservations for the available hw
breakpoint slots.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Cc: kgdb-bugreport@lists.sourceforge.net Cc: K.Prasad <prasad@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: torvalds@linux-foundation.org
LKML-Reference: <1264719883-7285-2-git-send-email-jason.wessel@windriver.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Härdeman [Thu, 28 Jan 2010 20:02:54 +0000 (21:02 +0100)]
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
Commit 6aa542a694dc9ea4344a8a590d2628c33d1b9431 added a quirk for the
Intel DG45ID board due to low memory corruption. The Intel DG45FC
shares the same BIOS (and the same bug) as noted in:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: David Härdeman <david@hardeman.nu>
LKML-Reference: <20100128200254.GA9134@hardeman.nu> Cc: <stable@kernel.org> Cc: Alexey Fisher <bug-track@fisher-privat.net> Cc: ykzhao <yakui.zhao@intel.com> Cc: Tony Bones <aabonesml@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Hugh Dickins [Fri, 29 Jan 2010 17:46:34 +0000 (17:46 +0000)]
mm: fix migratetype bug which slowed swapping
After memory pressure has forced it to dip into the reserves, 2.6.32's 5f8dcc21211a3d4e3a7a5ca366b469fb88117f61 "page-allocator: split per-cpu
list into one-list-per-migrate-type" has been returning MIGRATE_RESERVE
pages to the MIGRATE_MOVABLE free_list: in some sense depleting reserves.
Fix that in the most straightforward way (which, considering the overheads
of alternative approaches, is Mel's preference): the right migratetype is
already in page_private(page), but free_pcppages_bulk() wasn't using it.
How did this bug show up? As a 20% slowdown in my tmpfs loop kbuild
swapping tests, on PowerMac G5 with SLUB allocator. Bisecting to that
commit was easy, but explaining the magnitude of the slowdown not easy.
The same effect appears, but much less markedly, with SLAB, and even
less markedly on other machines (the PowerMac divides into fewer zones
than x86, I think that may be a factor). We guess that lumpy reclaim
of short-lived high-order pages is implicated in some way, and probably
this bug has been tickling a poor decision somewhere in page reclaim.
But instrumentation hasn't told me much, I've run out of time and
imagination to determine exactly what's going on, and shouldn't hold up
the fix any longer: it's valid, and might even fix other misbehaviours.
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: check total number of devices when removing missing
Btrfs: check return value of open_bdev_exclusive properly
Btrfs: do not mark the chunk as readonly if in degraded mode
Btrfs: run orphan cleanup on default fs root
Btrfs: fix a memory leak in btrfs_init_acl
Btrfs: Use correct values when updating inode i_size on fallocate
Btrfs: remove tree_search() in extent_map.c
Btrfs: Add mount -o compress-force
H. Peter Anvin [Fri, 29 Jan 2010 06:14:43 +0000 (22:14 -0800)]
x86: get rid of the insane TIF_ABI_PENDING bit
Now that the previous commit made it possible to do the personality
setting at the point of no return, we do just that for ELF binaries.
And suddenly all the reasons for that insane TIF_ABI_PENDING bit go
away, and we can just make SET_PERSONALITY() just do the obvious thing
for a 32-bit compat process.
Everything becomes much more straightforward this way.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 29 Jan 2010 06:14:42 +0000 (22:14 -0800)]
Split 'flush_old_exec' into two functions
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anuj Aggarwal [Fri, 29 Jan 2010 10:19:22 +0000 (15:49 +0530)]
ASoC: AM3517: ASoC driver not getting compiled
Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes
CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the
Makefile. Whereas the config option defined in Kconfig is
SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517
was not getting compiled.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Anuj Aggarwal [Fri, 29 Jan 2010 08:28:55 +0000 (13:58 +0530)]
ASoC: AIC23: Fixing writes to non-existing registers in resume function
Commit e9ff5eb2 (Fixing infinite loop in resume path) uses wrong AIC23
register in resume function because of which register writes happen
on some non-existing registers.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Henrik Rydberg [Fri, 29 Jan 2010 06:28:27 +0000 (22:28 -0800)]
Input: add the ABS_MT_PRESSURE event
For pressure-based multi-touch devices, a direct way to send sensor
intensity data per finger is needed. This patch adds the ABS_MT_PRESSURE
event to the MT protocol.
Requested-by: Yoonyoung Shim <jy0922.shim@samsung.com> Requested-by: Mika Kuoppala <mika.kuoppala@nokia.com> Requested-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
David Härdeman [Fri, 29 Jan 2010 06:28:27 +0000 (22:28 -0800)]
Input: winbond-cir - remove dmesg spam
I missed converting one dev_info call to deb_dbg before submitting the driver.
Without this change, a message will be printed to dmesg for each button press
if a RC6 remote is used.
projects / mirror_ubuntu-hirsute-kernel.git / log